Coal-fired thermal plants (CTPP) are known to pollute the atmosphere with emission of many greenhouse gases and particulate matter. The power generation from these thermal plants cannot be stopped completely because it forms the backbone of the grid power supply. It is necessary to study the dispersion patterns of pollutants that affect the health of the people. The dispersion patterns are location specific since they depend on local meteorological conditions. In this study, the dispersion of particulate matter (PM) and sulphur dioxide (SO₂) from a CTPP with 275 m high stack are studied under different atmospheric boundary layer (ABL) of neutral, stable and unstable conditions up to a distance of 30 km from the stack. The plume of the PM spreads under all conditions. During some parts of the day, PM settles around the stack while at other times PM keeps suspending in the air for the full distance under study. Sulphur dioxide dilutes to concentrations below the detection limits in about 12-13 km from the stack for neutral and unstable ABL whereas for the stable ABL, the dispersion is up to 30 km. The 24 h weighted average concentration of sulphur dioxide, at 10 m height from the ground, is 14.2 mg/m³ at a distance of 25 kms from the CTPP, which is comparable with the value of 9.2 mg/m³ measured at the Air Quality Stations located around the same distance. Based on the results policy changes that need to be implemented are suggested.

In the case of a severe accident, natural convection plays an important role in the atmosphere mixing of nuclear reactor containments. In the previous study, to simulate the natural convection in the accident scenario within a nuclear reactor containment, the steady thermal boundary conditions (BCs) were prescribed on either cooled or heated wall. The present study, therefore, aims at the transient 3D numerical simulations of natural convection of air around a cylindrical containment with unsteady thermal BCs at the vessel wall. For that purpose, the experiment series was done in the CIGMA facility at Japan Atomic Energy Agency (JAEA). The upper vessel or both the upper vessel and the middle jacket was cooled by subcooled water, while the lower vessel was thermally insulated. A 3D model was simulated with OpenFOAM®, applying the Unsteady Reynolds-averaged Navier–Stokes equations (URANS) model. Different turbulence models were studied, such as the standard k-ε, standard k-ω, k-ω Shear Stress Transport (SST) and, low-Reynolds-k-ε Launder-Sharma. The results of the four turbulence models were compared versus the results of experimental data. The k-ω SST showed a better prediction compare to other turbulence models. Also, the accuracy of the predicted temperature and pressure were improved when the heat conduction on the internal structure, i.e., flat bar, was considered in the simulation. Otherwise, the predictions on both temperature and pressure were underestimated compared with the experimental results. Hence, the conjugate heat transfer in the internal structure inside the containment vessel must be modeled accurately.

In this manuscript, an automated framework dedicated to design space exploration and design optimization studies is presented. The framework integrates a set of numerical simulation, computer-aided design, numerical optimization, and data analytics tools using scripting capabilities. The tools used are open-source and freeware, and can be deployed on any platform. The main feature of the proposed methodology is the use of a cloud-based parametrical computer-aided design application, which allows the user to change any parametric variable defined in the solid model. We demonstrate the capabilities and flexibility of the framework using computational fluid dynamics applications; however, the same workflow can be used with any numerical simulation tool (e.g., a structural solver or a spread-sheet) that is able to interact via a command line interface or using scripting languages. We conduct design space exploration and design optimization studies using quantitative and qualitative metrics, and to reduce the high computing times and computational resources intrinsic to these kinds of studies, concurrent simulations and surrogate-based optimization are used.

High-Rise buildings with their particular features can affects on surrounding environment and makes new microclimates. In the windy conditions, the spaces that are between building blocks changes to passages and affects on the wind velocity, intensity and it’s other parameters.The importance of this effect is different in each level of building height. The Pedestrian-Level is the lowest and one of important areas. Markets, playgrounds and pedestrian access had located in this area and any unwanted microclimate changes like high velocity and turbulence in this level can makes discomfort and dangerous condition for residents. So this research tries to consider the pedestrian- level wind comfort in some High-Rise building complexes arrangement that had located in Tehran district 22 with Computational Fluid Dynamics (CFD) modeling and reaching to a suitable arrangement pattern. It had collected the required data through field study and librarian databases and then compared them with standard guidelines and analyzed them by comparative comparison method. As a result a linear arrangement that placed crossover to wind direction for providing wind comfort and preventing wind danger is been suggested in this region.

Intelligent algorithms are recently used in the optimization process in chemical engineering and application of multiphase flows such as bubbling flow. This overview of modeling can be a great replacement with complex numerical methods or very time-consuming and disruptive measurement experimental process. In this study, we develop the adaptive network-based fuzzy inference system (ANFIS) method for mapping inputs and outputs together and understand the behavior of the fluid flow from other output parameters of the bubble column reactor. Neural cells can fully learn the process in their memory and after the training stage, the fuzzy structure predicts the multiphase flow data. Four inputs such as x coordinate, y coordinate, z coordinate, and air superficial velocity and one output such as pressure gradient are considered in the learning process of the ANFIS method. During the learning process, the different number of the membership function, type of membership functions and the number of inputs are examined to achieve the intelligent algorithm with high accuracy. The results show that as the number of inputs increases the accuracy of the ANFIS method rises up to almost for all cases, while the increment in the number of rules has a effect on the intelligence of artificial algorithm. This finding shows that the density of neural objects or higher input parameters enables the moded for better understanding. We also proposed a new evaluation of data in the bubble column reactor by mapping inputs and outputs and shuffle all parameters together to understand the behaviour of the multiphase flow as a function of either inputs or outputs. This new process of mapping inputs and outputs data provides a framework to fully understand the flow in the fluid domain in a short time of fuzzy structure calculation.

Aerodynamic performance of a floating offshore wind turbine (FOWT) is significantly influenced by platform surging motions. Accurate prediction of the unsteady aerodynamic loads is imperative for determining the fatigue life, ultimate loads on key components such as FOWT rotor blades, gearbox and power converter. The current study examines the predictions of numerical codes by comparing with unsteady experimental results of a scaled floating wind turbine rotor. The influence of platform surge amplitude together with the tip speed ratio on the unsteady aerodynamic loading has been simulated through unsteady CFD. It is shown that the unsteady aerodynamic loads of FOWT are highly sensitive to the changes in frequency and amplitude of the platform motion. Also, the surging motion significantly influences the windmill operating state due to strong flow interaction between the rotating blades and generated blade-tip vortices. Almost in all frequencies and amplitudes, CFD, LR-BEM and LR-uBEM predictions of mean thrust shows a good correlation with experimental results.

This work deals with the numerical investigation of the delivery of potential therapeutic agents through dentinal discs (i.e. a cylindrical segment of the dentinal tissue) towards the dentin-pulp junction. The aim is to assess the main key features (i.e. molecular size, initial concentration, consumption rate, disc porosity and thickness) that affect the delivery of therapeutic substances to the dental pulp and consequently to define the necessary quantitative and qualitative issues related to a specific agent before its potential application in clinical practice. The CFD code used for the computational study is validated with relevant experimental data obtained using micro Laser Induced Fluorescence (μ-LIF) a non-intrusive optical measuring technique. As the phenomenon is diffusion dominated and strongly dependent on the molecular size, the time needed for the concentration of released molecules to attain a required value can be controlled by their initial concentration. Finally, a model is proposed which, given the maximum acceptable time for the drug concentration to attain a required value at the pulpal side of the tissue along with the aforementioned key design parameters, is able to estimate the initial concentration to be imposed and vice versa.

This study assesses the impact of incorporating an adaptive learning mechanism into an agent-based model (ABMS) simulating behavior on a university campus during the course of a pandemic outbreak, with a particular case on the COVID-19 pandemic. The aim is to reduce overcrowding and infections on campus through the use of Reinforcement Learning (RL). Our findings indicate that RL is a viable approach for effectively representing agents’ behavior within this context. The results reveal specific temporal patterns of overcrowding violations. While our study successfully mitigated campus crowding, it had limited influence on altering the course of the epidemic. This highlights the necessity for comprehensive epidemic control strategies that consider the role of individual decision-making influenced by adaptive learning, along with the implementation of targeted interventions. This research significantly contributes to our understanding of adaptive learning within complex systems and offers valuable insights for shaping future public health policies in similar community settings. Future research directions encompass exploring various parameter settings and updating representations of the disease’s natural history.

This study explored the feasibility of fluoride removal from simulated semiconductor industry wastewater and its recovery as calcium fluoride using fluidized bed crystallization. The continuous reactor showed best performance (>90% fluoride removal and >95% crystallization efficiency) at a calcium to fluoride ratio of 0.6 within first 40 days of continuous operation. The resulting particle size increased by more than double during this time along with a 36% increase in the seed bed height indicating deposition of CaF2 onto the silica seed. The SEM-EDX analysis showed the size and shape of the crystals formed along with high amount of Ca-F ions presence. The purity of the CaF2 crystals were determined to be 91.1% though ICP-OES analysis. Following the continuous experiment, different process improvement strategies are explored. The addition of excess amount of calcium resulted in an additional 6% fluoride removal, however, compared to this single stage process, a two-stage approach was found to be better strategy to achieve a low effluent fluoride concentration. The fluoride removal reached 94% with this two-stage approach under optimum condition of 4 + 1 h HRT combinations and a [Ca2+]/[F-] ratio of 0.55 and 0.7 for the two reactors, respectively. CFD simulation showed the impact of inlet diameter, bottom-angle shape and width and height ratio of the reactor on mixing inside reactor and possibility of further improvement in reactor performance by optimizing the FBR configuration.

This article presents a detailed examination of the methodology and modeling tools utilized to analyze gas flow in pipelines, rooted in the fundamental principles of gas dynamics. The methodology integrates numerical simulations with modern neural network techniques, particularly focusing on the Physics-Informed Neural Network (PINN) method. This innovative approach combines artificial neural networks (ANNs) with physical equations, offering a more efficient and accurate way to model various complex processes and phenomena. The proposed mathematical model, based on the Euler equation, has been meticulously implemented using the Python language. Verification with analytical solutions ensures the accuracy and reliability of the computations. In the research, a comprehensive comparative analysis was conducted between results obtained using the PINN method and those from conventional Computational Fluid Dynamics (CFD) approaches. The analysis highlighted the advantages of the PINN method, which produced smoother pressure and velocity fluctuation profiles while reducing computation time, demonstrating its potential as a transformative modeling tool. The data derived from this study are of paramount importance for ensuring ongoing energy supply reliability and can also be used to create predictive models related to gas behavior in pipelines. The application of modeling techniques for gas flow simulation has the potential to revolutionize the integrity of our energy infrastructure and utilization of gas resources. However, it is crucial to emphasize that the effectiveness of such models relies on continuous monitoring and frequent updates to ensure alignment with real-world conditions. This research not only contributes to a deeper understanding of compressible gas flows but also underscores the crucial role of advanced modeling methodologies in the sustainable management of gas resources for both current and future generations.

To establish simulated micro-gravity conditions, biological organisms are placed on a simulated microgravity system, which primarily rotate in two or three dimensions and rely on slow sedimentation with latency to detect gravity. Fluid dynamics arise as a consequence of rotation of the chambers with in which the cells are filled. To minimize the effects of centrifugal forces, it is necessary to position the samples as close to the center of rotation as possible. Strong shear forces and velocities within the vessel can have an adverse impact on cells, making this a critical topic in cell biology. During experimental investigation, this specific phenomenon is not apparent, but numerical modelling readily illustrates and is not widely analyzed in literature's. Furthermore, bulk flask are frequently employed on random positioning machines (RPM), not merely because they demand a substantial quantity of reagents. The flask presented in the study can be easily developed and fitted in conventional cell culture plates containing medium and reagents similar to those used in ground experiments, thus allowing it to remain close to the center of rotation. In the present study, a series of fluid dynamics simulations are performed to examine the impact of shear forces within the microvessel presented under varying conditions using a foreign medium condition, and these results are compared with existing vessels by observing the effects of shear forces and maximum velocity zones.

In Active Flow Control (AFC) applications, to activate the boundary layer the use of pulsating flow has notorious energy advantages versus constant blowing/suction jet injections. For a given AFC application, five parameters, jet location and width, inclination angle, frequency of injection and momentum coefficient need to be tuned. Two main devices are nowadays capable of injecting pulsating flow with the sufficient momentum coefficient to delay the boundary layer separation, these are the Zero Net Mass Flow actuators (ZNMFA) and the Fluidic Oscillators (FO). In the present research, a novel FO configuration is analyzed for the first time at relatively high Reynolds numbers, fluid is considered as incompressible. After obtaining the typical linear correlation between the incoming Reynolds number and the outlet flow oscillating frequency, the effect of outlet width and mixing chamber wedge inclination angle dimensional modifications is addressed, modifications of the outlet width are observed to create large variations on the FO performance. The origin of the self-sustained oscillations is also analyzed in the present manuscript and greatly helps in clarifying the forces acting on the jet inside the mixing chamber. In fact we can conclude saying that the current FO configuration is pressure driven although the mass flow forces appear to be a much more relevant than in previous FO configurations studied.

The cavitation behavior of cryogenic liquids in the field of cryogenic engineering is distinct, showcasing fundamental differences from the cavitation behavior observed in ambient temperature water. Cavitation occurrence imposes severe limitations on the operational stability of cryogenic media transportation equipment, leading to safety concerns and increased manufacturing costs. Investigating the spatiotemporal characteristics of cavitation in cryogenic fluids holds significant value for both academia and engineering. The complexity of cavitation in cryogenic fluids primarily manifests through the coupled effects of thermodynamics, vortices, and bubbles during the cavitation process. In order to further explore the coupling mechanism, numerical simulations employing the Delayed Detached Eddy Simulation (DDES) turbulence model and Sauer-Schnerr cavitation model are conducted to validate the accuracy of the numerical calculations using the Hord experiment hydrofoil as a benchmark. Subsequently, the unsteady cavitation flow of liquid nitrogen around the NACA 0015 hydrofoil is simulated by the same numerical calculation method. The results indicate that the simulated results best coincide with experimental results when the bubble number density in the Sauer-Schnerr cavitation model reaches 108. The upstream development of the re-entrant jet under the driving force of inverse pressure gradient is the fundamental reason for the detachment of the primary cavitation zone. Under the same inflow cavitation number, the thermodynamic effect significantly inhibits the generation of bubbles and changes the range of the inverse pressure gradient, thus affecting the separation behavior of the primary cavitation zone.

Seepage erosion is one of the main reasons for the local collapse or instability of embankments. To investigate the characteristics and mechanism of seepage erosion for cohesionless soils, the model tests by using an independently developed seepage erosion device and the numerical simulations based on the Discrete Element Method-Computational Fluid Dynamics (DEM-CFD) coupling model were carried out. The results show that the seepage erosion process of the cohesionless soil can be characterized by four stages: stable seepage stage, fine particles upward migration stage, sand samples boiling stage, and erosion damage stage. The skeleton structure of soil sample under seepage flow is continually changed due to the loss of fine soil particles, which results in a significant decrease in the sample strength and may ultimately lead to the failure of the sample. The results of this study can provide references and bases for the design, construction, and long-term service of embankments or earth dams under the complex seepage condition, reducing the risk of seepage erosion.

The four-way reversing valve is a key component determining whether a heat pump air conditioning system can work. Studying the four-way reversing valve is of great significance for improving the performance of the heat pump air conditioning system. In this paper, the control equation of the sliding block movement process is constructed to simulate the reversing process of the four-way reversing valve in fluid mechanics, and a detailed study is carried out from the sliding block speed, sliding block acceleration, sliding block force, refrigerant leakage, and other aspects. Research has shown that optimizing the structure of the slider can greatly improve the working performance of the four-way reversing valve. Increasing the height of the slider not only improves the pressure relief ability of the four-way reversing valve and prevents the slider from being damaged by high-pressure gas impact, but also reduces the leakage of refrigerant during the directional process; When reducing the length of the slider, although it will improve the pressure relief capacity of the four-way reversing valve, it also increases the amount of refrigerant leakage. The research results provide a theoretical basis and improvement direction for designers to improve the performance of four-way reversing valves.

The present study explores the effect of using two porous deflectors on the performance of the Savonius wind turbine compared to only one porous deflector. The numerical simulation is performed to solve the unsteady Navier-Stokes equations using the SST k-

The pulsating flow is one of the techniques which can enhance heat transfer, therefore leading to energy saving in tubular heat exchangers. This paper investigates the heat transfer and flow characteristics in a two-dimensional in-line tube bundle with the pulsating flow by a numerical method using the Ansys Fluent. Numerical simulation is performed for Reynolds number Re = 500 with different frequencies and amplitude of pulsation. Heat transfer enhancement was estimated from the central tube of the tube bundle. Pulsation velocity had an asymmetrical character with a reciprocating flow. The technique developed by the authors to obtain asymmetric pulsations was used. This technique allows simulating an asymmetric flow in heat exchangers equipped with a pulsation generation system. Increase in both the amplitude and the frequency of the pulsations has a significant effect on heat transfer enhancement. Heat transfer enhancement is mainly observed in the front and back of the cylinder. At a steady flow in these areas, heat transfer is minimal due to the weak circulation of the flow. The increase in heat transfer in the front and back of the cylinder is associated with increased velocity and additional flow mixing in these areas.

Calculation of the pressure field on and around solid bodies exposed to external flow is of paramount importance to a number of engineering applications. However, conventional pressure measurement techniques are inherently linked to problems principally caused by their point-wise and/or intrusive nature. In the present paper, we attempt to calculate the time-averaged two-dimensional pressure field by integrating PIV (Particle Image Velocimetry) velocity measurements into a CFD code and modifying them by the respective correction step of the SIMPLE algorithm. Boundary conditions are applied from the PIV data as a three-layer area of constant velocities, adjacent to the boundaries. A novel characteristic of the approach is the straightforward inclusion of the Reynolds Stresses into the source terms of the momentum equations, calculated directly from the PIV statistics. The methodology is applied to three regions of the symmetry plane parallel to the main boundary layer flow past a surface mounted cube. In spite of findings of deviations from the planar 2D flow assumption, the derived pressure fields and the adjusted velocity fields are found to be reliable, while the intrinsic turbulent nature of the flow is considered without modelling of the Reynolds stresses.

The present is a study of the CFD simulations intended to simulate the emissions of pollutants that are generated after the combustion of proposed alternative aircraft fuels (Hydrogen, Ethanol and Methane) to compare with the emissions generated after the combustion of Kerosene and Benzene in a 2D cylindrical combustion chamber. Given that air traffic is a main contributor to not only 3% of man-made greenhouse effects but also of the generation of smog over heavy air traffic urban areas generating an impact on the air quality and the population of those areas.

Given the documented wave-induced damage of elevated coastal decks during extreme natural hazards (e.g. hurricanes) in the last two decades, it is of utmost significance to decipher the wave-structure-interaction of complex deck geometries and quantify the associated loads. Therefore, this study focuses on the assessment of solitary wave impact on open-girder decks that allow the air to escape from the sides. To this end, an arbitrary Lagrangian-Eulerian (ALE) numerical method with a multi-phase compressible formulation is used for the development of three-dimensional hydrodynamic models, which are validated against a large-scale experimental dataset of a coastal deck. Using the validated model as a baseline, a parametric investigation of different deck geometries with a varying number of girders Ng and three different widths, was conducted. The results reveal that the Ng of a superstructure has a complex role and that for small wave heights the horizontal and uplift forces increase with the Ng, while for large waves the opposite happens. If the Ng is small the wave particles accelerate after the initial impact on the offshore girder leading to a more violent slamming on the onshore part of the deck and larger pressures and forces, however, if Ng is large then unsynchronized eddies are formed in each chamber, which dissipate energy and apply out-of-phase pressures that result in multiple but weaker impacts on the deck. The decomposition of the total loads into slamming and quasi-static components, reveals surprisingly consistent trends for all the simulated waves, which facilitates the development of predictive load equations. These new equations, which are a function of Ng and are limited by the ratio of the wavelength to the deck width, provide more accurate predictions than existing empirical methods, and are expected to be useful to both engineers and researchers working towards the development of resilient coastal infrastructure.

The dynamic development of electromobility poses challenges to designers regarding not only the efficiency of energy transformation but also the battery life, which is influenced by the stability of its operating temperature. Designing cooling systems is connected not only with the optimization of energy management but also with other environmental parameters, such as noise emission. The paper presents the numerical optimization of an innovative radiator for use in electric buses in terms of energy consumption and noise emission. The results of the numerical studies were verified in laboratory and field conditions, showing a very good convergence of the model with the results of the experiments.

Consumer products contain the chemical substances that threaten human health. The modeling methods and experimental methods have been used to estimate the inhalation exposure concentration by the consumer products. The model and measurement methods have the spatial property problem and time/cost consuming problem, respectively. For solving the problems due to the conventional methodology, this study performed the feasibility of applying CFD for evaluation of inhalation exposure by comparing the experiment results and the zero-dimensional results with CFD results. To calculate the aerosol concentration, the CFD was performed by combined the 3D Reynolds averaged Navier Stoke’s equation and discrete phased model using ANSYS FLUENT. As a result of comparing the three methodologies performed under the same simulation/experimental conditions, we found the zero-dimensional spray model shows approximately 5 times underestimated inhalation exposure concentration when compared with the CFD results and measurement results in near field. Also, the results of the measured concentration of aerosols at five locations and the CFD results at the same location were compared to show the possibility of evaluating inhalation exposure at various locations using CFD instead of experimental method. The CFD results according to measurement positions can predict rationally the measurement results with low error. In conclusion, in the field of exposure science, a guideline for exposure evaluation using CFD was found that complements the shortcomings of the conventional methodology, the zero-dimensional spray model and measurement method.

This paper deals with the characteristics of the cyclone separator from the Lagrangian perspective to design important dependent variables, develops a neural network model for predicting the separation performance parameter, and compares the predictive performance between the traditional surrogate model and the neural network model. In order to design the important parameters of the cyclone separator based on the particle separation theory, the force acting until the particles are separated was calculated using the Lagrangian-based CFD methodology. As a result, it was proved that the centrifugal force and drag acting on the critical diameter having a separation efficiency of 50% were similar, and the particle separation phenomenon in the cyclone occurred from the critical diameter, and it was set as an important dependent variable. For developing a critical diameter prediction model based on machine learning and multiple regression methods, Unsteady-RANS analyzes according to shape dimensions were performed. The input design variables for predicting the critical diameter were selected as four geometry parameters that affect the turbulent flow inside the cyclone. As a result of comparing the model prediction performances, the ML model showed the 32.5 % of improvement rate of R2 compared to the traditional MLR considering the nonlinear relationship between the cyclone design variable and the critical diameter. The proposed techniques have proven to be fast and practical tools for cyclone design.

In this research, the computational fluid dynamic (CFD) approach that has been used in wind power generation field was applied for the solution of the problems of local strong wind areas in railway fields, and the mechanism of wind generation was discussed. At the same time, the affectivity of the application of computational fluid dynamic approach to railway field was discussed. The problem of local wind that occurs on the railway line in winter was taken up in this research. A computational simulation for the prediction of wind conditions by LES was implemented and it was clarified that the local strong wind area is mainly caused by separated flows originating from the small‐scale terrain positioned at its upstream (at approximately 180.0 m above sea level). Meanwhile, the effects of the size of calculation area and spatial grid resolution on the result of calculation and the effect of atmospheric stability were also discussed. It was clarified that when the air flow characteristic of the separated flow originating from the small‐scale terrain (at altitude of approximately 180.0 m) targeted in this research is reproduced at high accuracy by computational simulation of wind conditions, approximately 10.0 m of spatial resolution of computational grid in horizontal direction is required. As a result of the computational simulation of wind conditions of stably stratified flow (Fr = 1.0), lee waves were excited at the downstream of the terrain over time. As a result, the reverse‐flow region lying behind the terrain that had been observed at a neutral time was inhibited. Consequently, local strong wind area was generated at the downstream of the terrain and the strong wind area passing through the observation mast was observed. By investigating the speed increasing rate of local strong wind area induced at the time of stable stratification, it was found that the wind was approximately 1.2 times stronger than what was generated at a neutral time.

Unmanned Aerial Vehicles (UAVs) have gained significant attention in recent times due to their suitability to a wide variety of civil, military and societal missions. Development of an unmanned amphibious vehicle integrating the features of a multi-rotor UAV and a hovercraft is focus of the present study. Components and subsystems of the amphibious vehicle are developed with due consideration on aerodynamic, structural and environmental aspects. Finite element analysis (FEA) on static thrust conditions and skirt pressure are performed to evaluate the strength of structure. For diverse wind conditions and angles of attack (AOA), computational fluid dynamic (CFD) analysis is carried out to assess the effect of drag and suitable design modification is suggested. A prototype is built with a 7 kg payload capacity and successfully tested for stable operations in flight and water-borne modes. Internet of Things (IoT) based water quality measurement is performed in a typical lake and water quality is measured using pH, dissolved oxygen (DO), turbidity and electrical conductivity (EC) sensors. The developed vehicle is expected to meet functional requirements of disaster missions catering to the water quality monitoring of large water bodies.

The Gurney flap (GF) is a miniature lift-enhancement device and is usually mounted at the trailing edge of an airfoil. The GF and has been successfully applied to isolated airfoils, multi-element airfoils, and aircraft wings as well as helicopter rotor due to its attractive features of simplicity, cost-effective and separation control. The GF also has aroused the attention of researchers in the turbomachinery industry. However, limited studies are currently available on the application of a GF to an axial fan.Hence, in this paper, we conduct a wind tunnel and computational fluid dynamic (CFD) investigation on an axial fan profiled with a NACA 65-(12)10 airfoil to evaluate the effect of the GF on the performance of the fan. We also present the detailed flow features of the fan with and without the GF after validating the simulation results with the experimental results. The experimental results show that as the GF is installed higher on the fan blade, it can produce a higher total pressure rise accompanied with a greater loss of efficiency. The installation of the GF also enlarges the work capacity of the fan. Detailed flow field analysis, including the surface pressure distribution, vorticity distribution at the trailing edge and streamline distribution of the fan, is carried out to understand the mechanisms of the effect of the GF on the performance of the fan.

In this paper, a two-phase model of air shock wave induced by rock-fall was described. The model was made up of the uniform motion phase (velocity was close to 0 m·s^-1) and the acceleration movement phase. The uniform motion phase was determined by experience, meanwhile the acceleration movement phase was derived by the theoretical analysis. A series of experiments were performed to verify the two-phase model and obtained the law of the uniform motion phase. The acceleration movement phase was taking a larger portion when height of rock-fall was higher with the observations. Experimental results of different falling heights showed good agreements with theoretical analysis values. Computational fluid dynamics (CFD) numerical simulation had been carried out to study the variation velocity with different falling height. As a result of this, the two-phase model could accurately and convenient estimating the velocity of air shock wave induced by rock-fall. The two-phase model could provide a reference and basis for estimating the air shock waves' velocity and designing the protective measures.

In this paper the attention is focused on the analysis and the optimization of energy flows in networked systems via a fluid-dynamic model. In particular, a cost functional that represents a term proportional to the kinetic energy of an energy system is studied. First, the functional is optimized for a simple network having a unique node, with an incoming arc and two outgoing ones. The optimization deals with distribution coefficients and explicit solutions are found. Then, the global optimization is obtained using the local optimal parameters at the various nodes of the system. Considering the case study of an energy hub, interesting results are obtained for the whole network, proving the correctness of the proposed approach.

We present a new model formulation for a class of capacitated lot-sizing problem considering setup costs, product returns, and remanufacturing (CLSP-RM). We investigate a broad class of instances that fall into two groups, in the first group we can reformulate the problem with a relaxation and test whether the original problem is solvable. The relaxation gives near optimal solutions and the solution of this class does not give any difficulty to known solvers such as Cplex, Gurobi or Xpress. The second group of instances are of category NP and will be solved with a simple period-by-period simulation

This paper presents the common methods and corresponding drawbacks concerning nonlinear analysis of fluxgate excitation circuits and emphasizes the importance of nonlinear analysis for these circuits. With regard to the nonlinearity of the excitation circuit, this paper proposes the use of the core-measured hysteresis curve for mathematical analysis and the use of a nonlinear model that considers the coupling effect of the core and winding and influence of the historical magnetic field on the core for simulation analysis. The feasibility of mathematical calculations and simulation for the nonlinear study of fluxgate excitation circuit is verified via experiments. The results demonstrate that, in this regard, the simulation is better than a mathematical calculation. The simulation and experimental results of the excitation current and voltage waveforms under different excitation circuit parameters and structures are essentially consistent with each other, thereby verifying the effectiveness of the nonlinear excitation analysis method.

A rehabilitation technique for asphalt pavements with geosynthetic is the application of impregnated nonwoven geotextiles between deteriorated and new asphalt overlays. The performance investigation of impregnated geotextiles proves that they are enhancing in mechanical and hydraulic properties. Although, the installation process may cause severe impacts on these materials’ performance. During the installation, the geotextile suffers damage due to the traffic of high load vehicles, as compactors and pavers, and the friction with granular materials found under its layer or poured above it. This paper aims to investigate how the damage caused by granular materials on nonwoven geotextiles impregnated with different asphalt emulsions effect on their strength resistance and permittivity. From two types of nonwoven geotextiles: polypropylene and polyethylene terephthalate, the comparison uses geotextiles in three conditions: not impregnated, impregnated with asphalt emulsion of rapid setting, and impregnated with asphalt emulsion changed by an elastomeric polymer. Part of the samples followed the damage according to ISO 10722 procedure, placed between three different scenarios of granular materials, applying gravel, sand, and clay. After the damage process, the samples were submitted to mechanical and hydraulic properties evaluations.

We introduce a mission design for an interstellar expedition to nearby earth-like exoplanets, which our analysis determined to be Tau Ceti and Gliese 667C, at the time of analysis in 2013. We review the research problems in propulsion and AGI that must be addressed to launch an AI guided interstellar probe within 100 years. We propose a new semi-autonomous agent approach for intelligent control of the spacecraft. We introduce the concept of a semi-autonomous agent as having built-in safety guarantees that constrain operation. An autonomous agent case study is presented formulating the objective, constraints, AGI implementation of the agent based on Solomono's Alpha architecture, and adding specicity. We discuss the training required to reach human-level and trans-sapient levels of intelligence which corresponds to an entire crew of AI experts specialized in elds such as astrophysics, astromechanics, astrobiology, quantum physics, computer science, molecular biology, and so forth. We project the feasibility of the human-level AI technology based on empirical ndings in neuroscience, and nd that it should be feasible by 2030. We analyze Solomono's innity point hypothesis in light of Koomey's law about energy eciency of computing and nd that the trends in 2013 indicated an early singularity by 2035, which implies that we might encounter physical bottlenecks which will decelerate computing technology improvements signicantly. We recommend thus year 2040 for launching the probe by which date other required technologies will have been developed. We discuss the scenario of a virtual crew made of brain simulations, which is a bio-information based AI approach. We detail the subsystems of command and control, communication, scientic instrumentation, power, propulsion, navigation, and shielding. We propose a variation of ICAN-II/AIMStar propulsion which uses a positron source instead of anti-protons to initiate micro-fusion reactions. We combine the positron initiated fusion pulse propulsion scheme with a miniaturized version of the Daedelus fusion thruster obtaining high performance. We derive two mission proles one for fusion pulse propulsion, and the yet hypothetical Q-Thruster. Fusion thruster requires 132.2 years for Tau Ceti, and 233.2 years for Gliese 667C, while Q-Thruster takes only 42.3 years for Tau Ceti, and 62.5 years for Gliese 667C. We also discuss extended roles for intelligent interstellar probes such as self-reproduction via nanotechnology, refueling, construction, robotic bodies, and transmission of brain simulations.

Whether evaluating gridded population dataset estimates (e.g. WorldPop, LandScan) or household survey sample designs, a population census linked to residential locations are needed. Geolocated census microdata data, however, are almost never available and are thus best simulated. In this paper, we simulate a close-to-reality population of individuals nested in households geolocated to realistic building locations. Using the R simPop package and ArcGIS, multiple realizations of a geolocated synthetic population are derived from the Namibia 2011 census 20% microdata sample, Namibia census enumeration area boundaries, Namibia 2013 Demographic and Health Survey (DHS), and dozens of publicly available spatial datasets. Realistic household latitude-longitude coordinates are manually generated based on public satellite imagery. Simulated households are linked to latitude-longitude coordinates by identifying distinct household types with multivariate kmeans analysis, and modelling a probability surface for each household type using Random Forest machine learning methods. We simulate five realizations of a synthetic population in Namibia's Oshikoto region, including demographic, socioeconomic and outcome characteristics at the level of household, woman, and child. Comparison of variables in the synthetic population were made with 2011 census 20% sample and 2013 DHS data by primary sampling unit/enumeration area. We found that synthetic population variable distributions matched observed observations and followed expected spatial patterns. We outline a novel process to simulate a close-to-reality microdata census geolocated to realistic building locations in a low- or middle-income country setting to support spatial demographic research and survey methodological development while avoiding disclosure risk of individuals.

Blazars show rapid and high amplitude variability. In this work , Fermi daily light curve of 130 sources are analyzed, distribution of daily variability are compared with each other by using Kolmogorov-Smirnov (K-S) test. results show: 1)Some pairs of the distributions are similar; 2) In most cases, the distributions are not Gaussian.

In this work, we'll present the power spectra density, auto-correlation function, dentrended fluctuation analysis and multifractal spectrum are performed to the daily light curves of Blazars monitored by Fermi LAT. Some signs of power law are found.

Intersections within urban centers do not allow all citizens to move in a fluid manner. In this sense, this paper proposes a queuing network model based on Kendall's notation for the intersection of two urban streets (East 53rd Street and East 56th Street) in Panama City. A set of traffic lights operating under a fixed time scheme controls the vehicular flow at the intersection. The objective is to optimize the vehicular flow at the intersection by minimizing the waiting time of the vehicles using mathematical models, Linear Regressor Model, and simulations performed in MATLAB evaluating the waiting time experienced by the vehicles. Based on the results obtained, the optimal signal timing of the traffic lights is determined to minimize the waiting time for both streets.

The today competitive advantage of Ready-made garment industries depends on the ability to improve the efficiency and effectiveness of resource utilization. Ready-made garment industries have long historically adopted fewer technological and process advancement as compared to automotive, electronics and semiconductor industries. Simulation modeling of garment assembly line system has attracted a number of researchers as one way for insightful analysis of system behaviour and improving its performance. However, most of simulation studies have considered ill-defined experimental design which cannot fully explore the assembly line design alternatives and does not uncover the interaction effects of the input variables. Simulation metamodeling is an approach to assembly line design which has recently been of interest to so many researchers. However, its application in garment assembly line design has never been well explored. In this paper, simulation metamodeling of trouser assembly line with 72 operations has been demonstrated. The linear regression metamodel technique with resolution-V design was used. The effects of five factors: bundle size, job release policy, task assignment pattern, machine number and helper number on the production throughput of the trouser assembly line were studied. The increase of 28.63% of the production throughput was achieved for the best factors’ setting of the metamodel.

Polymerase chain reaction (PCR) technique is one of the molecular methods in amplifying DNA for the detection of malaria. However, the limitations of PCR especially when used for routine clinical practice can hamper its sensitivity and specificity. With that, this study focuses on designing a microfluidic device that will mimic the function of a conventional genus-specific PCR based on 18S rRNA gene to detect malaria parasites (Plasmodium falciparum) at low grade parasitemia. The design was drawn and simulated using ANSYS 14.5 Computational Fluid Dynamics (CFD). The simulation shows that adding loops to the design increases its relative deviation but to a minimal extent as compared to having only a straight path design, which indicates that looping is acceptable in designing a microfluidic device to minimize chip length. Also, increasing the cross-sectional area of the fluid path decreases the efficiency of the design, thus, the design with a relatively smaller cross-sectional area is favored. And lastly, among the three materials utilized, the chip made of polypropylene is the most efficient with a relative deviation of 0.94 as compared to polycarbonate and polydimethylsiloxane which have relative deviations of 2.78 and 1.92, respectively.

The Galleon was considered a masterpiece of shipbuilding in the sixteenth century, but from a modern point of view, the shape of her hull looks archaic and primitive. However, how accurate is this perception? Is the hull form of Galleon primitive? What were the reasons for its unique design features? This article investigates these questions by directly analysing the hull’s features from the point of view of modern ship’s theory, as well as from a historical perspective. A careful evaluation of specific design criteria of a typical Galleon, together with analysing a 3D model of its hull on modern software, with further insight for the seakeeping behaviour of Galleon with a comparison to more modern full-rigged ship (Barque of 19 CE), showed that these features were not random, but instead had a good rationale behind it, and served specific and carefully decided functions, required at the time.

Accurate prediction of the self-propulsion performance is one of the most important factors for energy-efficient design of a ship. In general, the hydrodynamic performance of a full-scale ship could be achieved by model-scale simulation or towing tank test with extrapolations. With the development of CFD methods and computing power, directly predict ship performance with full-scale CFD is an important approach. In this article, a numerical study on the full-scale self-propulsion performance with propeller operating behind ship at model- and full-scale is presented. The study includes numerical simulations using RANS method with double-model and VOF model respectively and scale effect analysis based on overall performance, local flow fields and detailed vortex identification. Verification study on grid convergence is also performed for full-scale simulation with global and local mesh refinements. And a series of sea trail tests were performed to collect reliable data for the validation of CFD predictions. The analysis of scale effect on hull-propeller interaction shows that the difference on hull boundary layer and flow separation is the main source of scale effect on ship wake. And the results of the fluctuations of propeller thrust and torque along with circulation distribution and local flow field show that propeller’s loading is significantly higher for model-scale ship. It is suggested that the difference on vortex evolution and interaction is more pronounced and have larger effects on ship’s powering performance at model-scale than full-scale according to the simulation results. From the study on self-propulsion prediction, it could be concluded that the simplification on free surface treatment does not only affect the wave-making resistance for bare hull but also the propeller performance and propeller induced ship resistance which can produced up to 5% uncertainty to the power prediction. Roughness is another important factor in full-scale simulation because it has up to approximately 7% effect on the delivery power. As a result of validation study, the numerical simulations of full-scale ship self-propulsion shows good agreement with the sea trail data especially for cases that have considered both roughness and free surface effects. This result will largely enhance our confidence to apply full-scale simulation in the prediction of ship’s self-propulsion performance in the future ship designs.

This study assesses the performance of the Weather Research and Forecasting (WRF) model using a high-resolution spatial grid (1 km) with various combinations of physical parameterization packages to simulate a severe event in August 2021 in the southeastern Brazilian coast. After determining the optimal set of physical parameterizations for representing wind patterns during this event, a year-long evaluation was conducted, covering forecast horizons of 24, 48, and 72 hours. The simulation results were compared with observational wind data from four weather stations. The findings highlight variations in the efficacy of different physical parameterization sets, with certain sets encountering challenges in accurately depicting the peak of the severe event. The most favorable results were achieved using a combination of Tiedtke (cumulus), Thompson (microphysics), TKE (boundary layer), Monin-Obukhov (surface layer), Unified-NOAH (land surface), and RRTMG (shortwave and longwave radiation). Over the one-year forecasting period, the WRF model effectively represented the overall wind pattern, including forecasts up to three days in advance (72-hour forecast horizon). Generally, the statistical metrics indicate robust model performance, even for the 72-hour forecast horizon, with correlation coefficients consistently exceeding 0.60 at all analyzed points. While the model proficiently captured wind distribution, it tended to overestimate northeast wind speed and gust intensities. Notably, forecast accuracy decreased as stations approached the ocean, exemplified by the ATPM station.

3D bioprinting, like 3D printing, is a process that builds structures by depositing material layer by layer. In the specific case of bioprinting, these layers are composed of a biocompatible material together with living cells, allowing the creation of three-dimensional structures that recreate functional tissues and organs. Bioprinting cell-laden structures is complicated by the high rate of cell damage and stress that occurs during the process, caused by the high pressures and stresses to which they are subjected. To minimise damage during the process, it is important to study and optimise certain bioprinting conditions beforehand and to analyse how they affect the cells by means of computational simulations. In this review, both quantitative and qualitative data are collected to improve the nozzle geometry through computational simulation studies. Optimal ranges for nozzle diameter (0.2-1mm) and length (8-10mm; 300-900μm) have been defined, and recommendations for improving nozzle performance during bioprinting, such as the provision of an inner angle of 20-30°, an inner EDTA coating and a shear stress of less than 10kPa, have been gathered. Finally, based on the data collected, a design of experiments is proposed to obtain an optimal bioprinting configuration for a particular bioink.

Given the problem of climate change caused by fossil fuels, there is a need to seek efficient alternative energies that have a lower impact on the environment and are obtained from renewable resources. Biomass gasification technology is attracting constant interest in sustainable energy research as an alternative to traditional combustion technology. Its numerous advantages include the availability of raw materials, reduction in harmful emission streams, performance, and costs. In gasification, thermochemical conversion of the raw material is carried out, obtaining a gaseous product of great interest known as synthesis gas. As this is a growing topic within the global energy framework, it is necessary to achieve the maturity of this technology by working on its weaknesses, mainly in terms of efficiency. The objective of this project was to study the hydrogen production process from the simulation of glucose gasification as a biomass model compound through a static model and a dynamic model, in order to determine the maximum concentration of the resulting components in each model studied. Since glucose is the most abundant component in biomass, it was used as a composite model, these models were built, and the basis for the adaptability of subsequent studies of optimization present one was laid. A H_2:CO ratio of 2.2 and molar fluxes were obtained for H_2,〖CO,CO〗_(2,) 〖CH〗_4 and H_2 O as would generally occur in an organic matter gasification process.

This paper starts with hypothesis (and presents some evidence) that anxiety in migrants is sufficiently important to be modelled. It presents a small (and very incomplete) review of emotion modelling in literature. It asks the question of how to translate these into agent-based modelling, and whether this can be orthogonal to specific modelling of goals and capabilities of agents. This short paper is offered as a motivator for discussion, rather than a discussion of results.

This study aims to understand the contents of debriefing performance in simulation education and its results by comprehensively examining the learning performance of the education ac-cording to the difference in the debriefing methods employed in domestic and overseas nursing simulation training. This is a literature review conducted to identify the effect of debriefing of simulation nursing practice education. The existing literature was found in electronic databases using Pubmed, Embase, MEDLINE complete, PsycINFO, Web of Science, CINAHL, the Cochrane Library, KoreaMed, National Discovery for Science Leaders, and Research Information Sharing Service and the key words were “nurse,” “nursing student,” “simulation,” “simulator,” “stand-ardized patient,” “debriefing.” Finally, 32 studies were analyzed. All the studies were conducted from 2012 to 2021. A total of 11 RCT, 17 quasi-experimental studies, 3 mixed method studies and 1 pilot study were identified. The debriefing process used media, structured questionnaires, and a method of teaching or peer-led debriefing. The outcome variables that were statistically significant were skill, performance, knowledge, problem-solving competency, critical thinking disposition, clinical judgement, self-confidence, satisfaction, and debriefing quality evaluation. It is necessary to educate the debriefers who are responsible for strategy development and meeting effective debriefing goals.

The aim of this paper is to examine the beneficial impact of feedback information in the dynamics of production-inventory control systems. Two production-inventory control system models are analyzed: APIOBPCS and 2APIOBPCS models. The simulation-based experiment designs were conducted by using the state-space equations of the two models. The bullwhip effect as measured by the variance ratio between the order rate and the consumption rate, and inventory responsiveness as measured by the Integral of Absolute Error between the actual and the target levels of inventory, are two metrics used to evaluate the performance of the production-inventory control system in response to a random customer demand. To ensure that both models work under optimal performance, multi-objective particle swarm optimization (MOPSO) is employed to address the problem of tuning the controller’s parameters. The simulation results show the 2APIOBPCS model outperforms the APIOBPCS model at achieving the desired bullwhip effect and being able to provide better inventory responsiveness. The improvement in the inventory responsiveness becomes more significant when the system operates under mismatched lead time and/or an initial condition.

Welded structures are subjected to internal residual stress after manufacturing that may affect the structural strength and normally are associated with an increase on initial geometrical imperfections. This study presents a simplified method to generate an adequate representation of residual stresses on Finite Element models for structural analysis of thin-walled structures and other applications. The results obtained shown that the methodology proposed to introduce residual stresses is simple, accurate and efficient on the modulation of post-welding stresses and their pattern, thus it may be used for simulation of the thermal process.

This publicly available simulation analysis compares baseline construction options versus sustainable options and evaluates both break-even costs as well as environmental effects. The simulation (https://rminator.shinyapps.io/sustain4/) provides users with comparative estimates based upon existing research on costs. This is the first simulation of its type that quantifies multiple sustainable construction options, associated break-even points, and environmental considerations for public use. Results estimate that a 100% solar solution for the baseline 3,000 square foot / 279 square meter house with 2 occupants results in a break-even of 9 years. The simulation includes options for rainwater harvesting or wells, Icynene foam, engineered lumber, Energy Star windows and doors, low flow water fixtures, aerobic / non-aerobic waste treatment or municipal services, and many other options. This is the first simulation of its type to provide publicly available sustainable construction analysis based on research, and it illustrates that sustainable construction might be both green for the environment and green for the pocketbook.

Several factors influence traffic congestion and overall traffic dynamics. Simulation modeling has been utilized to understand the traffic performance parameters during traffic congestions. This paper focuses on driver behavior of route selection by differentiating three distinguishable decisions, which are shortest distance routing, shortest time routing and less crowded road routing. This research generated 864 different scenarios to capture various traffic dynamics under collective driving behavior of route selection. Factors such as vehicle arrival rate, behaviors at system boundary and traffic light phasing were considered. The simulation results revealed that shortest time routing scenario offered the best solution considering all forms of interactions among the factors. Overall, this routing behavior reduces traffic wait time and total time (by 69.5% and 65.72%) compared to shortest distance routing.

This article aims to serve as a guide for the construction of supply chain simulation models designed with a lean approach, using Promodel software. To achieve this, a supply chain was designed for a fictitious company located in the City of Celaya, Guanajuato and a set of suppliers located in different cities within the same State. It was used as a google tool to define the distances between each of the companies. As a final result, a representative model of a supply chain was obtained, as well as a methodology that allows the construction of lean supply chains regardless of the number of companies that comprise it. The effect of the variability in the delivery times between suppliers was incorporated into the simulation model, as well as an equation that calculates the pollution emissions of the vehicles that integrate the network that moves the products between the companies. With this work it is possible to represent networks of supply chains of real world companies, where the variability and contamination factor is included, to facilitate the decision making regarding the number of vehicles, inventory levels, quantities to be shipped, frequency in the shipments, etc. with the purpose of contaminating as little as possible and at the same time preventing interruptions in the supply chain using the least amount of resources possible.

Project logistics is one of the specific logistics operations. Compared to other logistics operations, it needs more efficient planning and engineering applications in each operational process. On the other hand, each project logistics operation can be defined as tailor-made operations, since it has no similarity with other operations. Consequently, each project logistics operation should be planned and carried out according to its own conditions and parameters. This study focuses on the simulation of project logistics operations under the light of computerized applications from start to finish of the logistics operation. In this study, transportation operations of 600 tons of autoclave from the Petkim port to the Gördes building site were selected as a case study.

An empirical model is presented for estimating discharge on the Ubombo Sugar Limited (USL) main gravity canal to enhance bulk water management and water use efficiency. It uses stage readings obtained from measuring flumes A, B, C, and UPS to simulate discharge. The rationale for the development of the mathematical flow simulation model is the significance of the UPS flume as it measures readings that influence the daily operations of the farm, and the experiences with the ultrasonic flow meter installed in the flume. The model also provides a first for the simulation of accurate flow rates for flumes A, B, and C. A spreadsheet program that enables express prediction of canal flow rates was developed to influence timely implementation of these water management decisions. Calibrations demonstrated that the model is capable of predicting discharge at high accuracy (p>95%), and can be reliably used as a decision support tool for bulk water management. It can also be expanded to include other water measuring structures along Canal 1 and Canal 2, as well as the development of a stand-alone water management application for desktop and mobile computers.

The hepatic sinusoids are lined by thin endothelium containing transcellular pores dubbed fenestra. These fenestrations are completely open channels connecting the sinusoidal lumen to the underlying Space of Disse (SoD) and the hepatocytes of the liver parenchyma. The fenestrations are in the size range 0.05-0.35µm in diameter and cover between 5-15% of the sinusoidal endothelial surface area depending on their location along the sinusoids. Motivation/Research Question: So far, the narrowness of the sinusoids prevented the direct measurement of hemodynamic features such as sinusoidal pressure and flow velocity. A better understanding of these parameters might help in better understanding the physiology of the hepatic niche and possible implications in liver diseases. Few simulations of liver blood flow focus on the level of the individual sinusoid, fewer still include the transcellular pores (fenestrations) of the sinusoidal endothelium, and none have included i) a porosity gradient along the sinusoid wall modelled with through-all pores rather than a porus medium, ii) the presence of the Space of Disse, iii) lymphatic drainage. Model: Computed fluid dynamic (CFD) simulations performed using a numerical model with relevant anatomical characteristics (length, diameter, porous size and porosity). Boundary conditions included physiological/pathological values of inlet/outlet pressure and lymphatic outflow from the portal region of the SoD. Results: The pressure and flow velocity of the sinusoidal lumen was entirely dependent on the shape, i.e. constant versus divergent radius and not dependent on porosity in the sinusoidal wall. The velocity through the space of Disse (SoD) was affected by the addition of lymphatic drainage and increases in porosity in the pericentral area of the model. Variations in porosity also affected flow velocity through the fenestrations. Conclusions: The flow velocity in the SoD was modified by differences in porosity, while the flow velocity in the lumen of the sinusoids was unaffected, even by the absence of fenestrations. The overall shape of the vessel is the singular most important factor in the pressure flow behavior of the sinusoidal lumen. The flow rate over the hepatocytes is the flow rate through the SoD, and is modestly affected by the distribution of porosity along the sinusoid, and by the addition of a lymphatic drainage, this parameter would be of interest for modelling blood exchange with the hepatic parenchyma, especially if accounting for zonation.

This study aims to investigate the impact of body heat loss on the thermal and aerodynamic conditions in a whole-body cryotherapy chamber. The underlying hypothesis is that the heat generated by the human body alters the thermal and aerodynamic environment inside the cabin. A numerical study was conducted to test this hypothesis to analyze the thermodynamic exchanges between the human body and the cabin during a 3-minute whole-body cryotherapy session. The computational fluid dynamics (CFD) approach was used to study the unsteady heat transfer between the human body and the interior of the cryotherapy cabin. A thermal boundary condition, based on a mathematical model developed from experimental data, was applied to simulate skin cooling kinetics over time. The post-processing of the 3D results, including temperature, velocity fields, and thermal flux maps at the body surface, provided insight into the thermo-convective mechanisms involved in a whole-body cryotherapy session. The study found that body heat loss significantly affects the temperature fields inside the cabin, leading to global modifications of the aeraulic and thermal conditions. These findings suggest that cryotherapy protocols may need to be adjusted or the cabin set temperature optimized to enhance the therapeutic benefits.

This paper presents some results from a computational fluid dynamics (CFD) model of a multi-megawatt crosswind kite spinning on a circular path in a straight downwind configuration. The unsteady Reynolds averaged Navier-Stokes equations closed by the k−ω SST turbulence model are solved in the three-dimensional space using ANSYS Fluent. The flow behaviour is examined at the rotation plane, and the overall (or global) induction factor is obtained by getting the weighted average of induction factors on multiple annuli over the swept area. The wake flow behaviour is also discussed in some details using velocity and pressure contour plots. In addition to the CFD model, an analytical model for calculating the average flow velocity and radii of the annular wake downstream of the kite is developed. The model is formulated based on the widely-used Jensen’s model (Technical Report Risø-M; No. 2411, 1983), which was developed for conventional wind turbines, and thus has a simple form. Expressions for the dimensionless wake flow velocity and wake radii are obtained by assuming self-similarity of flow velocity and linear wake expansion. Comparisons are made between numerical results from the analytical model and those from the CFD simulation. The level of agreement was found to be reasonably good. Such computational and analytical models are indispensable for kite farm layout design and optimization, where aerodynamic interactions between kites should be considered.

In this paper, an attempt has been made to analyze the effect of spool port/ groove geometry on the pressure drop and chamber pressures which effect the performance parameters of the flow distributor valve. The work mainly involves formulation of detailed mathematical model of the valve and compare them on the same platform. For mathematical modelling, Matlab has been used. The size of the orifices is considered same throughout the model for better comparison. Initially the construction and functioning of flow distributor valve along with working principles of hydrostatic motor (Rotary Piston) is shown. Next shown the analytical analysis of area change and pressure drops due to different geometry of the spool valve ports. After that the computational fluid dynamics (CFD) analysis has been shown. A complete mathematical model to describe such flow distributor valve is developed after having a comprehensive knowledge of orifice characteristics, flow interactions based on valve geometry. Equations of flow through different orifices (fixed and variable area) of the valve have been developed based on the relationships obtained earlier.

The paper proposed a modification of the GeoSER(D) model previously developed by us by detailing the age structure of the population, personal schedule on weekdays and working days, and individual health characteristics of the agents, this made it possible to build a more realistic model of the functioning of the city and its residents. The developed model made it possible to simulate the spread of 3 types of the strain of the COVID-19 virus, and to analyze the adequacy of this model in the case of unhindered spread of the virus among city residents. The paper showed that SARS COV 2 spreads mainly from contacts in workplaces and transport, and schoolchildren and preschool children are the consequence, not the initiator of the epidemic. Fluctuations in the dynamics of various indicators of the spread of SARS COV 2 associated with the difference in the daily schedule on weekdays and weekends. It has been shown that people's daily schedules strongly influence the spread of SARS COV 2. For the more contagious "rapid" strains of SARS COV 2 (omicron), immunocompetent people become a significant source of infection. For the less contagious "slow strains" (alpha) of SARS COV 2, the most active source of infection is immunocompromised individuals (pregnant women). The more contagious – "fast" strain of the SARS COV 2 virus (omicron) spreads faster in public transport. For less contagious – "slow" strains of the virus (alpha), the greatest infection occurs due to work and educational contacts.

This paper shows that by applying the Nyquist-Shannon sampling theorem, the spatial and temporal resolution of a simulation can be no more than half the resolution of the simulating reality. This has significant implications for not only the values of the observables in the simulation but also its physical laws. This progressive halving of nested simulations coupled with the minimum resolution compatible with the production of a simulation also sets a limit to the nestedness of a lineage of simulations (it is by no means infinite). The limit of nestedness is then used to calculate the probability that we are living in a simulation assuming a single base reality. This will be shown to be significantly lower than popular expectation. A Kardashev-like scale, with three variants, is also developed to gauge the technological advancement of a civilization in relation to the extent to which it can extract information from space and time.

A case of low level windshear at Beijing Daxing International Airport is studied in the present pa-per. It is related to the synoptic scale/mesoscale changes of the airflow pattern over northern China. The shear was captured well by the Doppler LIDAR at the airport and timely alerts had been issued. This study considers the technical feasibility of forecasting the shear feature using a high resolution numerical weather prediction model with a lead time of several hours. It turns out that the shear feature could be forecast well, and is generally consistent with the actual observations. However, there are still discrepancies between reality and the simulation, such as the strength of the shear and persistency of the feature. More cases of windshear at Daxing airport would be studied in the fu-ture in order to understand the nature of windshear over there.

The genus Flavivirus includes 53 members and poses a big threat to human health among worldwide. Diseases caused by flavivirus infections can be broadly classified into hemorrhagic diseases (Dengue, Yellow fever, etc) and neurological diseases (West Nile disease, Zika disease, etc). Many flaviviruses still lack specific treatments and effective vaccines. In this context, it becomes particularly important to thoroughly characterize the pathogenesis of flavivirus infection and develop animal models. Therefore, animal models that can accurately simulate human diseases are essential for evaluating the effectiveness of therapeutic drugs and preventive vaccines. In this paper, we provide a comprehensive review of the currently available animal models that support flavivirus infection and exhibit clinical manifestations related to flavivirus infection. Additionally, we discuss the strengths and limitations of each animal model, aiming to enhance researchers understanding of the use of animal models in flavivirus research. This insight is intended to facilitate further studies into the pathogenesis of flavivirus, as well as the development of antiviral agents and vaccines.

A systematic investigation of the dynamic clustering behavior of active particles under confinement, including the effects of both particle density and active driving force is presented based on a hybrid coarse-grained molecular dynamics simulation. First, a series of scaling laws were derived with power relationships for the dynamic clustering time as a function of both particle density and active driving force. Notably, the average number of clusters N ̅ assembled from active particles in the simulation system exhibits a scaling relationship with clustering time t described by N ̅∝t^(-m). Simultaneously, the scaling behavior of the average cluster size S ̅ is characterized by S ̅∝t^m. Our findings reveals the presence of up to four distinct dynamic regions concerning clustering over time, with transitions contingent upon the particle density within the system. Furthermore, as the active driving force increases, the aggregation behavior also accelerates, while an increase in density of active particles induce alterations in the dynamic procession of the system.

Fatigue fractures in materials are the main cause of approximately 80% of all material failures, and it is believed that such failures can be predicted and mathematically calculated in a reliable manner. It is possible to establish prediction modalities in cases of fatigue fracture, according to three fundamental variables in fatigue, such as volume, number of fracture cycles, as well as applied stress, with the integration of Weibull constants (length characteristic). This investigation was carried out mechanical fatigue tests on specimens smaller than 4 mm2 in section of different industrial materials for their subsequent analysis through precision computed tomography in search of microfractures. The measurement of these microfractures, along with their metrics and classifications, was recorded. A convolutional neural network trained with deep learning was used to achieve the detection of microfractures in image processing. The detection of microfractures in images with 480x854 or 960x960 pixels is the primary objective of this network, and its accuracy is above 95%. Images that have microfractures and those that do not are classified by the network. Subsequently, by means of image processing, the microfracture is isolated. Finally, the images that do contain this feature are interpreted by image processing to obtain their area, perimeter, characteristic length, circularity, orientation, and type microfracture metrics. All values will be obtained in pixels and converted to metric units (μm) through a conversion factor based on image resolution.

The article presents the method of identification of dynamic models for different flight states of a rotary-wing UAV. Experimental flights were conducted to obtain data necessary for the identification process. Such models can later be implemented in simulations to represent the behavior of real-life objects. Simulation of UAV swarms is the first stage of developing a swarm system, where prototyping with physical models is problematic. Therefore, obtaining accurate models is crucial for the simulation process to be reliable. Also, verification of obtained models was performed to make sure that they were identified correctly. In particular, the presented method was proven effective and successfully used in some applications.

Deciding when to replace dairy bulls presents a complex challenge for artificial insemination (AI) companies. These decisions encompass multiple factors, including a bull's age, predicted semen production, and estimated genetic merit. This study's purpose was to provide a practical, objective tool to assist in these decisions. We utilized a Markov Chain model to calculate the economic valuation of dairy bulls, incorporating key factors such as housing costs, collection and marketing expenses, and the bull's probable tenure in the herd. Data from a leading AI company were used to establish baseline values. The model further compared a bull's net present value to that of a potential young replacement, establishing a relative valuation (BullVal$). The range of BullVal$ observed spanned from -$316,748 to $497,710. Interestingly, the model recommended culling for 49% of the bulls based on negative BullVal$. It was found that a bull's net present value was primarily influenced by market allocation and pricing, coupled with the interaction of semen production and genetic merit. This study offers a robust, data-driven model to guide bull replacement decisions in AI companies. Key determinants of a bull's valuation included market dynamics, semen production rates, and genetic merit.

In this study, the Bohler K 190 steel was used. The steel was manufactured by the powder metallurgy (PM) process. The boronizing process was carried out in the range of 1173 to 1323 K, for 1-10 h. The samples were boronized in solid medium, called the Durborid powder mixture. For the microstructural observations, the scanning electron microscopy was utilized for determining the morphology of interfaces and measuring the layers’ thicknesses. The phase composition of boride layers was also determined with X-ray diffraction analysis. To investigate the redistribution of chemical elements redistribution during the boronizing process, the EDS mapping and EDS point analysis were used. The boride layers were constituted by FeB and Fe2B phases except for 1173 K for 1 h. The values of Vickers microhardness of Fe2B, FeB and transition zone were estimated. Finally, to assess the boron activation energies in FeB and Fe2B, the so-called integral method was applied and the results in terms of activation energies were confronted with the literature data.

The annual energy matrix has been changing in the last years because of the necessity of less dependence on fossil fuels, which are running out on the planet. Therefore, a study was started to simulate the most efficient production of H2 through COMSOL Multiphysics®, as it is a gas that in the future will be essential to supply the world's energy necessities, due to its easy to get and insert in piped gas pipes. From this study, we were able to present an optimization of parameters that presents good indications of how to obtain efficient hydrogen production in an idealized reactor.

The current theories of consciousness do not address the two major problems:What is the solution to the hard problem of consciousness or What is the experience of self-existence? and How is conscious perception computed? We address these questions using our hypothesized theory:The Self Simulation theory and propose a model of computation of consciousness.The components of the model are an interconnected network of auxiliary processors or Auxiliary Neural Networks(AN) which receives input from the external sensory modalities,computes a representation of the information and relays it to the NCC(Neural Correlates of Consciousness), the NCC – a processing unit which can be neuro anatomically distributed in location but computationally connected to each other and to the Auxiliary Networks,and a working memory which the NCC references for further computation of information.Computation of conscious perception is achieved via the decoding of the content of the memory by the NCC.The self simulation theory accounts not only for the various phenomenal experiences but also experimentation paradigms conducted in the past.

Although train simulation research is vast, most available network simulators do not track the instantaneous movements and interactions of multiple trains for the computation of energy/fuel consumption. In this paper, we introduce the NeTrainSim simulator for heavy long-haul freight trains on a network of multiple intersecting tracks. Trains are modeled as a series of moving mass points (each car/locomotive is modeled as a point mass) while ensuring safe following distances between them. The simulator considers the motion of the train as a whole and neglects the relative movements between the train cars/locomotives. Furthermore, the powers of the different locomotives are transferred to the first locomotive as such a simplification result in a reduced simulation time without impacting the accuracy of energy consumption estimates. While the different tractive forces are combined, the resistive forces are calculated at their corresponding locations. The output files of the simulator contain pertaining information to the train trajectories and the instantaneous energy consumption levels. A summary file is also provided with the total energy consumed for the full trip and the entire network of trains. Two case studies are conducted to demonstrate the performance of the simulator. The first case study validates the model by comparing the output of NeTrainSim to empirical trajectory data using a basic single-train network. The results confirm that the simulated trajectory is precise enough to estimate the electric energy consumption of the train. The second case study demonstrates the train-following model considering six trains following each other. The results showcase the model’s ability in relation to maintaining safe-following distances between successive trains. Finally, the NeTrainSim is demonstrated to be scalable with computational times of O(n) for less than 50 trains (n) and O(n²) for higher number of trains.

The oncogenic potential of high-risk HPVs is focused on producing the E6 and E7 oncoproteins responsible for disrupting the control of the cell cycle. Epidemiological studies propose the presence of the N29S and H51N variants of the HPV16 E7 protein as a significant association with cervical cancer. It has been suggested that changes in the amino acid sequence of E7 variants may affect the oncoprotein 3D structure; however, this remains unknown. Analysis of the structural differences of the HPV16 E7 protein and its variants (N29S and H51N) was performed through homology modeling and structural refinement by molecular dynamics simulation. We propose for the first time a 3D structure of the E7 reference protein and two of its variants (N29S and H51N) and conclude that the mutations induced by the variants in N29S and H51N have a significant influence on the 3D structure of the E7 protein of HPV16, which could be related to the oncogenic capacity of this protein.

Metallic glass matrix composites are unique new materials which have superior mechanical properties as compared to existing conventional materials. Owing to this, they are potential candidates for various future structural applications. However, they suffer from disadvantages of brittleness, poor ductility and little or no toughness and they manifest catastrophic failure on application of force. Their behavior is dubious and require extensive experimentation to draw conclusive results. In present study, which is continuation of previous study by author, an effort has been made to overcome this pitfall by simulation. A quantitative mathematical model based on KGT theory has been developed to describe nucleation and growth of crystalline phase dendrites in glassy matrix during solidification. It yields information about numerical parameters to understand the behavior of each individual element in a phase in multicomponent sluggish slurry and their effect on final microstructural evolution. Model is programmed and simulated in MATLAB®. Its validation is done by comparison with identical curves reported in literature previously for similar alloys. Results indicate that effect of incorporating all heat transfer coefficients at macroscopic level and diffusion coefficients at microscopic level play a vital role in refining the model and bringing it closer to actual experimental observations. Two types of hypoeutectic and eutectic systems namely Zr₆₅Cu₁₅Al₁₀Ni₁₀ and Zr_47.5Cu_45.5Al₅Co₂ respectively were studied. Simulation results were found to be in good agreement with prior simulated and experimental values

Susceptible, infective, recovered, and hospitalized/isolated individuals are placed on the cells of a nxn square lattice, where each cell is occupied by a single individual or is vacant. At discrete time units (typically one day each) all susceptibles and infectives execute a random movement and when a coincidence of the two types occurs the susceptible is converted to infective status according to some probability. Infectives are labelled by the number of days since originally infected. At each time increment the age label of the infectives is increased by one unit. When the label reaches a number like 15 or 20 days the susceptibles recover with some probability or become isolated/hospitalized. Upon reaching some age the latter types either recover or die. Probabilities for the movements and conversions from one status to another are implemented by random numbergeneration. Simulations were carried out to investigate the effect of several probability and age parameters, the size of population (proportional to nxn) and density (related to fraction of occupied cells), and the size of the movements. Mid-term gradual conversion of susceptibles to isolated was explored as intervention policy.

The novel Coronavirus (COVID-19) is spreading and has caused a large-scale infection in China since December 2019. Thefirst infected person was declared on March 18, 2020 in Djibouti. This has led to a signicant impact on the lives and economy in Djibouti and other countries. In this study, we propose a double compartment stochastic model which describes the evolution of the infection rate and the evolution of the number of infected in the period from May 20 to June 23, 2020. We will also propose the evolution of people infected in two states, recovered and deceased.

Molecular dynamics simulations were carried out to investigate the atomic structure of a model Cu64Zr36 bulk metallic glass (BMG). It is found that the amount of icosahedral content of the system is significantly increased in a well relaxed structure. While we considered four connection types of vertex-, edge-, face-, and volume-sharing, the huge cluster in the relaxed samples mainly involve volume-type connection and exhibits a remarkable athermal plasticity that great stiffness and great yield strength compared to the as-quenched samples. In addition, the bond-angle distribution of annealed sample shows sharp peaks at specific bond angles which is an evidence of crystallized Laves-phase formed by icosahedral atoms, however the peaks are to be broaden after loading, which indicates decreasing amount of icosahedral content and their shape distortion. These results suggest that icosahedral content in a bulk metallic glasses plays a key role to determine the mechanical properties such as rigidity and maximum stress carrying capacity.

Network Simulators is typically used to study services and applications in complex scenarios due to the infeasibility of deploying real testbeds. Many problems can be solved by using network simulators such as NS-3. With this in mind, the aim of this article is to introduce new NS-3 users through detailed information. It is sometimes difficult to handle by new users the traditional manuals developed by NS-3 project official website. In this article, NS-3 for communication network and Eclipse Integrated Development Environment (IDE) for powerful programming language are integrated step-by-step, explaining the main features of these open source software packages and concluding with an example simulation. Our effort is to make it easy for a beginner to be part of the NS-3 research community and to maintain an open environment of knowledge.

In this report we have discussed the important role of molecular modeling, especially the use of the molecular dynamics method, in investigating transport processes in nanoporous materials such as membranes. With the availability of high performance computers, molecular modeling can now be used to study rather complex systems at a fraction of the cost or time requirements of experimental studies. Molecular modeling techniques have the advantage of being able to access spatial and temporal resolution which are difficult to reach in experimental studies. For example, sub-Angstrom level spatial resolution is very accessible as is sub-femtosecond temporal resolution. Due to these advantages, simulation can play two important roles: Firstly because of the increased spatial and temporal resolution, it can help understand phenomena not well understood. As an example, we discuss the study of reverse osmosis processes. Before simulations were used it was thought the separation of water from salt was purely a coulombic phenomenon. However, by applying molecular simulation techniques, it was clearly demonstrated that the solvation of ions made the separation in effect a steric separation and it was the flux which was strongly affected by the coulombic interactions between water and the membrane surface. Additionally, because of their relatively low cost and quick turnaround (by using multiple processor systems now increasingly available) simulations can be a useful screening tool to identify membranes for a potential application. To this end, we have described our studies in determining the most suitable zeolite membrane for redox flow battery applications. As computing facilities become more widely available and new computational methods are developed, we believe molecular modeling will become a key tool in the study of transport processes in nanoporous materials.

MCrAlX (M: Ni or Co or both, X: minor elements) coatings have been widely used to protect hot components in gas turbines against oxidation and hot corrosion at high temperatures. Understanding the influence of the X-elements on oxidation behaviour is important in the design of durable MCrAlX coatings. In this study, NiCoCrAlX coatings doped with Y+Ru and Ce, respectively, were deposited on Inconel-792 substrate by HVOF. The samples were subjected to isothermal oxidation test in laboratory air at 9000, 1000, 1100 ºC and cyclic oxidation test between 100 ºC and 1100 ºC with 1 hour dwell time at 1100 ºC. It was observed that the coating with Ce shows a much higher oxidation rate than the coating with Y+Ru under both isothermal and cyclic oxidation tests. Besides, β-depletion due to interdiffusion between coating and substrate was significantly lower with Ru addition. Simulations results using both a moving phase boundary model and an established oxidation-diffusion model show that Ru stabilize β grains which reduces β-depletion of coating due to substrate interdiffusion. This paper presents a comprehensive study of the influence of Ce and Ru on oxidation behaviour including investigation of the microstructure evolution influenced by oxidation time at coating surface and coating-substrate interface combining experiment and simulation results.

In the present paper, laminar forced convection nanofluid flows in a uniformly heated horizontal tube were revisited by direct numerical simulations. Single and two-phase models were employed with constant and temperature-dependent properties. Comparisons with experimental data showed that the mixture model performs better than the single-phase model in the all cases studied. Temperature-dependent fluid properties also resulted in a better prediction of the thermal field. A particular attention was paid to the grid arrangement. The two-phase model was used then confidently to investigate the influence of the nanoparticle size on the heat and fluid flow with a particular emphasis on the sedimentation process. Four nanoparticle diameters were considered: 10, 42, 100 and 200 nm for both copper-water and alumina/water nanofluids. For the largest diameter dnp = 200 nm, the Cu nanoparticles were more sedimented by around 80 %, while the Al₂O₃ nanoparticles sedimented only by 2.5 %. Besides, it was found that increasing the Reynolds number improved the heat transfer rate, while it decreased the friction factor allowing the nanoparticles to stay more dispersed in the base fluid. The effect of nanoparticle type on the heat transfer coefficient was also investigated for six different water-based nanofluids. Results showed that the Cu-water nanofluid achieved the highest heat transfer coefficient, followed by C, Al₂O₃, CuO, TiO₂, and SiO₂, respectively. All results were presented and discussed for four different values of the concentration in nanoparticles, namely φ = 0, 0.6, 1 and 1.6%. Empirical correlations for the friction coefficient and the average Nusselt number were also provided summarizing all the presented results.

In systems biology, biological phenomena are often modeled by ODE and distributed in the de facto standard file format SBML. The primary analyses performed with such models are dynamic simulation, steady-state analysis, and parameter estimation. These methodologies are mathematically formalized, and libraries for such analyses have been published. Several tools exist to create, simulate, or visualize models encoded in SBML. However, setting up and establishing analysis environments is a crucial hurdle for non-modelers. Therefore, easy access to perform fundamental analyses of ODE models is a significant challenge. We developed SBMLWebApp, a web-based service to execute SBML-based simulations, steady-state analysis, and parameter estimation directly in the browser without the need for any setup or prior knowledge to address this issue. SBMLWebApp visualizes the result and numerical table of each analysis and provides a download of the results. SBMLWebApp allows users to select and analyze SBML models directly from the BioModels Database. Taken together, SBMLWebApp provides barrier-free access to an SBML analysis environment for simulation, steady-state analysis, and parameter estimation for SBML models. SBMLWebApp is implemented in Java™ based on an Apache Tomcat® web server using COPASI, the SBSCL, and LibSBMLSim as simulation engines. SBMLWebApp is licensed under MIT with source code available from https://github.com/TakahiroYamada/SBMLWebApp. The program runs online at http://simulate-biology.org.

Efficient implementation of clean energy technologies, including pioneering solutions like mobile solar PV systems mounted on trailers (MSPT), is pivotal for addressing energy challenges, especially in regions with constrained power grid access. This endeavour is vital for meeting escalating elec-tricity demands and aligning with the UN Sustainable Development Goal (SDG) aimed at ensuring dependable and sustainable energy provision in developing countries. This paper investigates the aerodynamic behaviour of a designed MSPT using numerical and experimental approaches. Spe-cifically, the study focuses on the effects of wind velocity and tilt angels on the drag and lift forces, as well as drag and lift coefficients on the panel used in the MSPT system. Additionally, the overall wind force acting on the entire MSPT (including 9 large solar PV panels) was examined, considering the combined effects of wind flow and the system's geometry. The simulations were conducted using ANSYS-Fluent software and experimental testing was performed utilizing scaled-down models to validate the accuracy of the simulation. The insights and the knowledge from this study can be utilized to optimize the design, installation, and operation of such systems, ultimately enhancing their performance, reliability, and paving ways for further improvements in mobile solar PV technology.

This work presents a design and model of the thermo-hydrodynamic behavior applying CFD for pin-fin heat sink with square shape (rectangular fin profile), through a novel pin arrangement that improves heat removal in the system. The novelty consist in the insertion of a deflector row that will help to direct the flow, so it hits the rectangular cross-sectional fins the presents in the system. The heat sink model is placed in channel designed in which air flows as suitable medium, and its overall performance is investigated. In addition, a constant heat flux is applied to the bottom wall of the heat sink model, equal values and amounts that​ correspond to the heat fluxes generated by current electronic equipment and devices. The numerical results of the global thermal resistance, the pressure drop and the Nusselt number are reported. The results allow determining best arrangement or geometry configuration, location and functionality of the fin-deflectors were collocated for evaluate thermal-hydraulic efficiency of system.

new subsonic blower wind tunnel design has been studied both numerically and experimentally, it is also referred to as “blower” wind tunnel. This paper, is initially aimed to address each sequential stage of the wind tunnel design process. Rather than applying the standard method of modelling solely the flow in the test section, a large-scale CFD model of the whole wind tunnel was employed. The loss of every constituent element was calculated and then all the losses are added up to determine the power needed for the wind tunnel operation which is used as “intake fan” boundary conditions in the CFD model. Then, flow uniformity and turbulent intensity measurements in an empty test section using a Pitot-static tube and hot wire anemometer (HWA) were introduced to validate the CFD results. The results showed that flow quality was significantly affected by boundary layer controllers (honeycomb and mesh screens) in the settling chamber and wide-angle diffuser. Investigations were also conducted to evaluate the flow deficit in the wake area behind a convex hump model using HWA. This was additional experimental tests carried out to validate the suitability of the wind tunnel flow aerodynamic research.

A general procedure is described, to generate material parameter sets to simulate fire propagation in horizontal cable tray installations. Cone Calorimeter test data is processed in an inverse modelling approach. Here, parameter sets are generated procedurally and serve as input for simulations conducted with the Fire Dynamics Simulator (FDS). The simulation responses are compared with the experimental data and ranked based on their fitness. The best fitness was found for a test condition of \SI{50}{\kilo\watt\per\meter^2}. Low flux conditions \SI{25}{\kilo\watt\per\meter^2} and less exhibited difficulties to be simulated accurately. As a validation step, the best parameter sets are then utilised to simulate fire propagation within a horizontal cable tray installation and are compared with experimental data. It is important to note, the inverse modelling process is focused on the Cone Calorimeter and not aware of the actual validation step. Despite this handicap, the general features in the fire development can be reproduced, however not exact. The fire in the tray simulation extinguishes earlier and the total energy release is slightly higher as compared to the experiment. The responses of the material parameter sets are briefly compared with a selection of state of the art procedures.

In order to be able to face competition, thriving corporations have to be compelled to maintain an awfully smart relationship with their existing customers and additionally to be able to anticipate their future wants. Thus, corporations do not target customers as teams, however they’re attempting to focus on them as individuals. However, to be able to use this information, corporations have to be compelled to use promoting automation tools. Marketing Automation was an idea first introduced in 2001 by John D.C. Little in his presentation at the 5th Invitational Choice Symposium UC Berkeley 2001. This survey paper assesses prominent research on Marketing Automation and suggests how it can be modified to adapt to the current marketing scenario.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

This study presents an extensive collection of data on the aerodynamic behavior at a low Reynolds number and geometric coefficients for 2900 airfoils obtained through the class shape transformation (CST) method. By employing a verified OpenFOAM-based CFD simulation framework, lift and drag coefficients were determined at a Reynolds number of 10^5. Considering the limited availability of data on low Reynolds number airfoils, this dataset is invaluable for a wide range of applications, including unmanned aerial vehicles (UAVs) and wind turbines. Additionally, the study offers a method for automating CFD simulations that could be applied to obtain aerodynamic coefficients at higher Reynolds numbers. The breadth of this dataset also supports the enhancement and creation of machine learning (ML) models, further advancing research into the aerodynamics of airfoils and lifting surfaces.

Abstract：Ballast pick-up velocity is a crucial parameter in the design of a slurry system in excavating devices, it influences transportation stability, safety, and economy of the system. In this study, a vertical pipe hydraulic experiment with different ballast sizes under water condition was conducted to investigate the ballast pick-up velocity in the shield slurry system. Thereafter, the coupling method of computational fluid dynamics and the discrete element method (CFD-DEM) was employed to establish a numerical model of the ballast pick-up velocity in the shield slurry system, and its applicability was verified by comparing the experiment results. Additionally, the ballast pick-up process under actual working conditions was studied, and the influence of ballast size and concentration on pick-up velocity was investigated. Overall, the primary findings of the study are as follows: 1) The numerical method can be applied to predict both the single ballast and ballast group pick-up velocity. 2) The pick-up process of the ballast group can be divided into four stages. 3) The conveying velocity of the ballast should be higher than the pick-up velocity of the single ballast to facilitate smooth discharge. 4) For a certain increase in ballast concentration, the pick-up velocity tends to be stable.

This paper analyses the health and performance of 12-stage axial compressor of the TV3-117VM/VMA turboshaft operated in a desert environment. The results of the dimensional control of 4,800 worn blades are analysed to model the wear process. Operational experience and numerical simulations are used to assess the effectiveness of an Inlet Particle Separator. Numerical modal analysis is performed to generate the Campbell diagram of worn blades and identify resonant blade vibration which can lead to high cycle fatigue (HCF). It is shown that the gradual loss of the stall margin over time determines the serviceability limits of compressor blades. Recommendations setting out go / no-go criteria are made to maintenance and repair organisations.

This work studied the corrosion of welded pipes and how welding destroyed surface film of pipes. Surface reaction of a welded pipe is key to understanding phenomena and important factors during the corrosion. This paper presents experiment and CFD modeling approaches of a welded pipe corrosion under salt vapor condition. The pipes were welded at currents of 60 A,70 A and 80 A to observe the effect of welding current on corrosion. A welded pipe is a stainless-steel ASTM A312 grade 304L and period of experiment about 0-600 hours that they are tested in vertical and horizontal alignments. In CFD software, there is not direct model of corrosion but it can use surface reaction and create add-on species and chemical reaction technique for imitating the corrosion mechanism. The modeling approaches of corrosion have presented in 3-dimensional transient times in CFD simulation. Surface reactions were performed by Species Model which involve site species. Site species in Species Model took place at gas-solid interfaces and in this case are salt vapor and surface pipe. Chemical reaction rate on the surface controls lost weight of a welded pipe and the model can be validated with experiment. In conclusion, in period 0-600 hours error between CFD modeling and experiment have error trend decreased. The error at 600 hours is 6% both of vertical pipe and horizontal pipe test. The modeling approaches closely with the performed experiment and can be accepted. Moreover, the model is able to predict corrosion of a welded pipe of different sizes and their lost weight after 600 hours without experiment. Also the model can predict lifetime of pipe.

Bioprocesses for the production of renewable energies and materials lack efficient separation processes for the utilized microorganisms such as algae and yeasts. Dissolved air flotation (DAF) and microflotation are promising approaches to overcome this problem. The efficiency of these processes depends on the ability of microorganisms to aggregate with microbubbles in the flotation tank. In this study, different new or adapted aggregation models for microbubbles and microorganisms are compared and investigated for their range of suitability to predict the separation efficiency of microorganisms from fermentation broths. The complexity of the heteroaggregation models range from an algebraic model to a 2D population balance model (PBM) including the formation of clusters containing several bubbles and microorganisms. The effect of bubble and cell size distributions on the flotation efficiency is considered by applying PBMs, as well. To determine the impact of the model assumptions, the modeling approaches are compared and classified for their range of applicability. Evaluating computational fluid dynamics (CFD) of a DAF system shows the heterogeneity of the fluid dynamics in the flotation tank. Since analysis of the streamlines of the tank show negligible backmixing, the proposed aggregation models are coupled to the CFD data by applying a Lagrangian approach.

Subgrid scale models for unresolved turbulent fluxes are investigated with a focus on combustion for space propulsion applications. An extension to the gradient model is proposed, introducing a dependency on the local burning regime. The dynamic behavior of the model's coefficients is investigated, and scaling laws are studied. The discussed models are validated using a DNS database of a high-pressure turbulent fuel-rich methane-oxygen diffusion flame. The operating point and turbulence characteristics are selected to resemble those of modern combustors for space propulsion applications to support the future usage of the devised model in this context.

The rapid integration of Information and Communication Technology (ICT) is transforming the traditional electrical grid into a {\em Smart Grid}. Smart grids enable two-way communication and improved monitoring and control between utilities and customers. However, due to its heterogeneous nature, public exposure, and weak security at low-powered devices, the Smart Grid has vulnerabilities to various malicious threats, adversaries, and cyber attacks, which may affect cost and service availability. Additionally, when the systems' confidentiality, integrity, or availability are compromised, the resulting fallout can threaten national security and have cascading effects on human lives. Given the extreme consequences of an attack, smart-grid technology must be thoroughly tested for correct operation and security {\em before} it is deployed. As a result, vulnerability testing of smart grids, not only for correctness but for security purposes, has been the subject of numerous studies by academics, government agencies, and private companies. This paper reviews the vulnerabilities associated with the smart grid and spotlights simulation as the vulnerability testing methodology conducted in recent pertinent research works. It also presents various security aspects of the smart grid, including grid applications, system and network infrastructure and components, cyber threats and attacks, simulation, and different mitigation techniques. Finally, we analyze the gaps in the current research works, focusing on simulation. We briefly present a real-time simulation testbed that mimics customer behaviour and integrates hardware in the loop to apply attack methods, analyze vulnerabilities and risk mitigation associated with the smart grid system, and propose future work to improve the current framework.

The paper outlines a methodology for developing a model to estimate energy consumption in electric vehicles (EVs). The most robust validation indicators were exhibited by an artificial intelligence method, specifically neural networks. Within this framework, two predictive models for EV energy consumption were developed for winter and summer conditions, based on actual driving cycles. Such models hold particular significance for microscale road analyses. The resultant model for test data in summer conditions demonstrates validation indicators with an R2 of 86% and an MSE of 1.4, while for winter conditions, the values are 89% and 2.8, respectively, confirming its high precision. The paper also presents exemplary applications of the developed models, utilizing both real and simulated microscale data. The results obtained and the presented methodology can be especially advantageous for decision-makers in city road management and infrastructure planners, aiding both cognitive understanding and better planning of charging infrastructure networks.

Daylighting has been widely adopted in recent years due to its potential to improve the indoor environment in terms of visual comfort and energy-saving. One of the energy-saving techniques for energy-efficient buildings is the integration of louver systems. Louvers are considered more efficient for providing daylight in the interior as compared to other daylighting systems. Here, this paper presents the design of a louver system for conducting energy simulations for lighting and cooling requirements in office spaces. The simulation results indicate that the use of louvers in different opening configurations can lead to energy savings, particularly in the lighting aspect. The louver system in office spaces with a 50% louver opening leads to 27.0% energy savings. Further, the results are presented for different louver openings to calculate the lighting and cooling energy savings. The overall performance of the system is better in terms of providing consistent daylight, which eventually improves energy saving.

Matrix asphalt material has poor road performance, which is improved by adding polymer modified agents. The original asphalt material experiment research has a certain limitation in that it cannot truly expose the mechanism and influence of modifiers on asphalt materials. To explore the gain effect of the modified agent on the asphalt material's road performance, the molecular dynamic simulation technology is used to explain its mechanism in the micro dimension. The three parameters of the free volume score, radial distribution function and average directional shift diffusion coefficient are analysed to improve the performance of the modifier on asphalt material, an exploration of the microdimension shows that the amount of SBS modifiers is 6% and the amount of rubber modified asphalt material is 22%. The improvement of materials is better than that of rubber modifiers.

Compressed gas storage of hydrogen has emerged as the preferred choice for fuel cell vehicle man- ufacturers, as well as for various applications like road transport, and aviation. However, designers face increasing challenges in designing safe and efficient composite overwrapped pressure vessels (COPVs) for hydrogen storage. One challenge lies in the development of precise software that con- sider a multitude of factors associated with the filament winding process. These factors include layer thickness, stacking sequence, and the development of particularly robust models for the dome region. Another challenge is the formulation of predictive behavior and failure models to ensure that COPVs have optimal structural integrity. The present study offers an exploration of numerical methods used in modeling COPVs, aiming to enhance our understanding of their performance characteristics. The methods examined include finite element analysis in Abaqus, involving conventional shell elements, continuum shell elements, three-dimensional solid elements, and specialized homogenization tech- niques for multilayered composite pressure vessels. Through rigorous comparisons with type-III pressure vessels from the literature, the research highlights the most suitable choice for simulating COPVs and their practicality. Finally, we propose a new design for type-IV hydrogen composite pressure vessels using one explored method, paving the way for future developments in this critical field.

Using metaheuristics, such as the Evolutionary Algorithm (EA), within control structures is a realistic approach for certain optimal control problems. Their role is often predicting the optimal control values over a prediction horizon using a process model (PM). The big computational effort sometimes causes problems. Our work addresses a new issue: whether a machine learning (ML) algorithm could “learn” the optimal behaviour of the couple (EA, PM). A positive answer is given by proposing datasets apprehending this couple's optimal behaviour and appropriate ML models. Following a design procedure, a number of closed-loop simulations will provide the sequences of optimal control and state values, which are collected and aggregated in a data structure. For each sampling period, datasets are extracted from the aggregated data. The ML algorithm experiencing these datasets will produce a set of regression functions. Replacing the EA predictor with the ML model, new simulations are carried out, proving that the state evolution is almost identical. The execution time decreases drastically because the PM’s numerical integrations are totally avoided. The performance index equals the best-known value. In different case studies, the ML models succeeded in capturing the optimal behaviour of the couple (EA, PM) and yielded efficient controllers.

This paper proposes a metaphysical framework for distinguishing between human and machine intelligence. By drawing an analogy from Kant’s incongruent counterparts, it posits two identical deterministic worlds -- one comprising a human agent and the other comprising a machine agent. These agents exhibit different types of information processing mechanisms despite their apparent sameness in a causal sense. By postulating the distinctiveness of human over machine intelligence, this paper resolves what it refers to as “the vantage point problem” – namely, how to legitimize a determinist’s assertion of determinism by placing the determinist within the universe.

Abstract: The population issue has been increasingly urgent in China in recent years. Fertility desire is an essential component of fertility research. Studies on fertility desire mainly contain two aspects: socio-economic structure and individual family[1]. The psychological structure of individuals in individual families is the primary factor of fertility desire. Based on the parasocial relationship theory, this study analyzed the changes in real behavioral intention achieved by players through the identification and attachment to avatars while constructing parasocial relationships[2]. The results indicate that character attachment can significantly enhance the variables of game concentration and player self-identity, actively mediates parasocial emotions and parasocial cognition, and ultimately increases fertility desire. As a theoretical contribution, this study provides a comprehensive interpretation of the psychology of Chinese players in a Simulation Game and explores the theoretical connections among role attachment, role identity, and parasocial relationships in virtual game players.

With an explosion of data in the nearly every domain, from physical and environmental sciences to econometrics and even social science, we have entered a golden era of time-domain data science. In addition to ever increasing data volumes and varieties of time-series, there's a plethora of techniques available to analyses them. Unsurprisingly, machine learning approaches are very popular. In environmental sciences (ranging from climate studies to space weather/solar physics), machine learning (ML )and deep learning (DL) approaches complement the traditional data assimilation approaches. In solar and astrophysics, multiwavelength time-series or lightcurves along with observations of other messengers like gravitational waves provide a treasure trove of time-domain data for ML/DL approaches for modeling and forecasting. In this regard, deep learning algorithms such as recurrent neural networks (RNNs) should prove extremely powerful for forecasting as it has in several other domains. Such methods agnostic of the physics can only predict transient flares that are represented in the original distribution trained on (eg. coloured noise fluctuations) and not special, isolated episodes (eg. a one-off outburst like a major coronal mass ejection) potentially distinguishing them. Therefore it is vital to test robustness of these techniques ; here we attempt to make a small contribution to this by exploring sensitivity of RNNs with some rudimentary experiments. We test the performance of a very successful class of RNNs, the Long Short Term Memory (LSTM) algorithms with simulated lightcurves. As an example, we focus on univariate forecasting of time-series (or lightcurves) characteristic certain variable astrophysical objects (eg. active galactic nuclei or AGN). Specifically, we explore the sensitivity of training and test losses to key parameters of the LSTM network and data characteristics namely gaps and complexity measured in terms of number of Fourier components. We find that typically, the performances of LSTMs are better for pink or flicker noise type sources. The key parameters on which performance is dependent are batch size for LSTM and the gap percentage of the lightcurves. While a batch size of $10-30$ seems optimal, the most optimal test and train losses are under $10 \%$ of missing data for both periodic and random gaps in pink noise. The performance is far worse for red noise. This compromises detectability of transients. Thus, we show that generative models (time-series simulations) are excellent guides for use of RNN-LSTMs in building forecasting systems

Plasmonics is the study of resonant oscillations of free electrons in metals caused by incident electromagnetic radiation. Surface plasmons can focus and steer light on the subwavelength scale. Apart from metals, plasmonic phenomena can be observed in soft matter systems such as electrolytes where resonant charge oscillations can be induced for ions in solution. Due to their larger mass, they are plasmon-active in a lower frequency regime and on a larger wavelength scale. Spatial confinement allows increasingly strong charge interactions and gives rise to nonlocality or spatial dispersion effects. These effects manifest as additional longitudinal propagation modes and are known to cause plasmonic broadening and resonance shifts in metal nanostructures. We derive and discuss the nonlocal optical response of ionic plasmons using a hydrodynamic, two-fluid model in a planar homogeneous three-layer system with electrolyte-dielectric interfaces. Studying such systems enables us to identify and understand plasmonic phenomena in biological and chemical systems.