Deep eutectic solvents (DESs) are known as tunable solvents. It is possible to prepare ternary deep eutectic solvent (TDES) are used for desired purpose by selecting the suitable molar ratio and components of mixture. Therefore, four DESs and two TDESs were prepared in this work. DESs and TDESs were prepared with potassium carbonate (PC) as a hydrogen bond acceptor (HBA) and three hydrogen bond donors (HBDs) such as glycerol (GL), ethylene glycol (EG) and 2-amino-2methyl-1-3-propanediol (AMPD) known as a hindered amine (HA). Binary DESs were PC-GL with molar ratios 1:10 and 1:16 and PC-EG with the same molar ratios. TDES were prepared by adding AMPD in binary DESs such as PC-GL-AMPD 1:16:1 and PC-EG-AMPD 1:10:1. The experimental density and refractive index of all DESs and TDESs were measured at the temperature of 293.15 to 343.15 K with an interval of 5 K. The effect of temperature, molar ratio and alkyl chain length on the properties was investigated. The molar volumes and isobaric thermal expansion were calculated using experimental density data. The experimental refractive index data was used to derive the specific refraction, molar refraction, free molar volume, electronic polarization, polarizability constant and internal pressure at several temperatures.

Nanographene oxide (GOn) constitutes a nanomaterial of high value in the biomedical field. However, large scale production of highly stable aqueous dispersions of GOn is yet to be achieved. In this work, we explored high-power ultrasonication as a method to reduce particle size of GO and characterized the impact of the process in the physico-chemical properties of the material. GOn was obtained with lateral dimensions of 99 ±43 nm and surface charge of −39.9 ± 2.2 mV. High-power ultrasonication enabled an improvement of stability features, particularly by resulting in a decrease of the average particle size, as well as zeta potential, in comparison to GO obtained by low-power exfoliation and centrifugation (287 ± 139 nm; −29.7 ± 1.2 mV). Re-markably, GOn aqueous dispersions were stable for up to 6 months of shelf-time, with a global process yield of 74%. This novel method enabled the production of large volumes of highly con-centrated (7.5 mg mL-1) GOn aqueous dispersions. Chemical characterization of GOn allowed the identification of characteristic oxygen functional groups, supporting high-power ultrasonication as a fast, efficient and productive process for reducing GO lateral size, while maintaining the material’s chemical features.

Background: Food waste has been a major social problem in recent years. Annually, 1.3 billion tons of food is wasted worldwide. It is recommended that food waste should be reduced at every stage of production. By-products from food processing have high nutritional value; therefore their use in the design of new products is advisable. Methods: By-products from tomato processing (tomato waste-TW) and pepper (defatted pepper seeds-DPS, pepper placenta-PP) were used at a level of 10-30% to produce extruded pasta. The farinographic characteristics, chemical composition, cooking quality, and color of the pasta were studied. Results: The results showed a significant up to 27% increase in the protein content in the TW30 samples, compared to the control. The TDF content increased over five times in DPS30 and TW30 (27.99% and 25.44%). The amino acid composition of the pasta improved with the fortification, but failed to achieve the complete protein by FAO. The DPS30, PP20, PP30, and all TW samples can be considered high-protein products according to the EU definition (min. 20% energy from protein). Conclusion: Vegetable waste can be a valuable additive for improvement of the nutritional value of food. Their addition is part of the zero-waste trend, which has a positive impact on the environment.

FPGA-based cards for data concentration and readout are often used in data acquisition (DAQ) systems for high-energy physics experiments. The DMA engines implemented in FPGA enable efficient data transfer to the processing system’s memory. This paper presents a versatile DMA engine. It may be used in systems with FPGA-equipped PCIe boards hosted in a server and MPSoC-based systems with programmable logic connected directly to the AXI system bus. The core part of the engine is implemented in HLS to simplify further development and modifications. The design is modular and may be easily integrated with the user’s DAQ logic, assuming it delivers the data via a standard AXI-Stream interface. The engine and accompanying software are designed with flexibility in mind. They offer a simple single-packet mode for debugging and a high-performance multi-packet mode fully utilizing the computational power of the processing system. The number of used DAQ cards and the amount of memory used for the DMA buffer may be modified in runtime without rebooting the system. That is particularly useful in the development and test setups. The paper also presents the development and testing methodology. The whole design is open-source and available in public repositories.

At present, failure definition and damage characteristic curve (DCC) analysis included in the framework to assess bitumen fatigue cracking performance have an inconsistency in ranking bitumen fatigue behaviour. This study utilized two types of self-healing polymers (STP and IPA1w) to modify the neat asphalt (NA), and research four different types of bitumens: NA, STP-modified bitumen, IPA1w-modified bitumen, and styrene-butadiene-styrene modified bitumen (SBSB), to evaluate the above-mentioned framework. All bitumens were subjected to short-term and long-term aging and tested utilizing the Linear amplitude sweep (LAS) test and simplified viscoelastic-continuum-damage (S-VECD) model. The results showed that the SBSB exhibited the highest numbers of loading cycles (in long-term aging analysis) to reach failure points at 25°C, 28°C, and 31°C which were 2290, 2340, and 2510, respectively. However, this bitumen failed to exhibit the best performance in terms of DCC assessment under the same conditions, confirming the above-mentioned inconsistency. Besides, the current failure criterion could not accurately predict bitumen fatigue behaviour under certain test conditions because two R2 values were below 0.1. As a result, this study proposed a new failure definition and failure criterion to overcome these issues. The proposed failure definition agreed with the DCC analysis to rank bitumen fatigue performance, and the proposed failure criterion showed R2 values higher than 0.9. The new framework presented the modified bitumen containing 0.5% of STP as the asphalt binder with the best fatigue cracking performance, according to the selected test conditions.

In-situ observation on the austenite grain growth and martensite transformation in a developed NM500 wear-resistant steel were conducted on a Confocal Laser Scanning High-temperature Microscope (CSLM). Results indicated that the martensite nucleation did not synchronously proceed during quenching process. The selective prenucleation dominated in martensite nucleation, which dividing untransformed austenite into several regions, and resulting in the larger size of fresh martensite. Martensite can not only nucleate at parent austenite grain boundaries, but also nucleate in the preformed martensite laths and twins. Smaller constraint in the martensite growth was achieved in a larger parent austenite grain size, leading to the longer fresh martensite and secondary martensite. Besides, the transformation kinetics of martensite was accelerated in a higher quenching temperature. Moreover, the martensitic laths presented in parallel laths (0~2°) based on the pre-formed lath or distributed in triangle, parallelogram or hexagon with an angle of 60° or 120°. Interestingly, martensitic lath also traversed the unstable new parent austenitic grain boundaries. In addition, the size of austenite grains increased with the quenching temperature, and austenite grains coarsened in a short time at a higher quenching temperature of 1160 ℃. Furthermore, a large amount fine dispersed particles redissolved and ripped at 1160 ℃, resulting in the many large and visible carbonitrides.

Guava is a vital fruit worldwide, especially in Pakistan, and due to its nutritional value famous in each age group. Due to a very short shelf life, the marketing and export of this fruit faced severe constraints. Therefore, in the current study, edible coating of chitosan (0, 0.5, 1.0, 1.5, and 2.0%) was evaluated on postharvest shelf life when guava fruits were stored (room temperature and 4 °C temperatures) for 12 days. The chitosan treated coating fruits have shown reduced total sugars and malondialdehyde levels compared to untreated control samples. However, a significant difference (p ≤ 0.05) in total sugar and malondialdehyde levels exists between samples stored in m compared to refrigerated temperature (4 °C). The chitosan-coated samples have shown a greater amount of vitamin C, quercetin, rutin, and total phenolic contents than control samples. However, these nutritional parameters' levels were significantly different (p ≤ 0.05) in samples stored at room than samples stored at refrigerated temperature. However, the levels of crude fiber, potassium, and sodium were found statistically nonsignificant (p ≥0.05) in control versus chitosan treated coating treatments. The findings have documented that the coatings of 1.5 and 2.0% were most effective for extension in shelf life and maintaining the nutritional attributes of guava fruit.

The high-resolution bistatic lidar developed at the Physikalisch-Technische Bundesanstalt (PTB) aims to overcome the limitations of conventional monostatic lidar technology which is widely used for wind velocity measurements in wind energy and meteorology applications. Due to the large measurement volume of a combined optical transmitter and receiver tilting in multiple directions, monostatic lidar generally has poor spatial and temporal resolution. It also exhibits large measurement uncertainty when operated in inhomogeneous flow, for instance, over complex terrain. In contrast, PTB’s bistatic lidar uses three dedicated receivers arranged around a central transmitter, resulting in an exceptionally small measurement volume. The coherent detection and modulation schemes used allow the detection of backscattered, Doppler shifted light down to the scale of single aerosols, realising the simultaneous measurement of all three wind velocity components. This paper outlines design details and the theory of operation of PTB’s bistatic lidar and provides an overview of selected comparative measurements. The results of these measurements have shown that the measurement uncertainty of PTB’s bistatic lidar is well within the measurement uncertainty of traditional cup anemometers, while being fully independent of its site and traceable to the SI units. This allows its use as a transfer standard for the calibration of other remote sensing devices. Overall, PTB’s bistatic lidar shows great potential to universally improve the capability and accuracy of wind velocity measurements, such as for the investigation of highly dynamic flow processes upstream and in the wake of wind turbines.

Acute high altitude illnesses are of great concern for physicians and people traveling to high altitude. High Altitude Pulmonary Edema (HAPE) can be better understood through the Oxygen Transport Triad which involves the Pneumo-Dynamic Pump (Ventilation), the Hemo-Dynamic Pump (Heart and circulation), and Hemoglobin. The two pumps are the first physiologic response upon initial exposure to hypobaric hypoxia. Hemoglobin is the balancing energy-saving time-evolving equilibrating factor. The increased hemoglobin at high altitude reduces the percentage of dissolved oxygen in the arterial oxygen content with respect to sea level. At high altitude, the acid-base balance must be adequately interpreted using the high altitude Van-Slyke correction factors. Pulse-oximetry measurements during breath-holding at high altitude allow for the evaluation of high altitude diseases. The Tolerance to Hypoxia Formula shows that, paradoxically, the higher the altitude the more tolerance to hypoxia. All organisms adapt physiologically and optimally to a high-altitude environment to survive. Reduction of pulmonary hypertension in HAPE through oxygen administration results in a favorable outcome.

An oxidation resistant coating on cemented tungsten carbides is characterised in this work. Cemented tungsten carbides (cWCs) are routinely used in mining and manufacturing but are also candidate materials for compact radiation shielding in fusion power generation. In both environments, cWCs will suffer significant degradation due to oxidation at relatively low temperatures. In a recent study, a Si-deposition coating method was demonstrated to improve the oxidation resistance of cWCs by up to a factor of 1,000. This work focusses on the growth kinetics, phase composition, and mechanical properties of these coatings. By combining quantitative X-ray diffraction, electron microscopy and nanoindentation, we show that the coating layer has a 20 % higher hardness than the substrate, which was explained on the basis of a previously-unknown presence of a fine distribution of very hard SiC laths. To interpret the coating stability, a coating growth map is developed. The map shows the structure is stable under a broad range of processing temperatures and composite compositions, demonstrating the potential application of these coatings in a variety of nuclear shielding cWCs.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

Keywords: Geobacillus thermocatenolatus; lipases; ethanolysis; ionic liquids; kinetic resolution; mandelic acid.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (>70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

Ultra-high temperature oxidation-resistant alloys (UTORAs) have received a lot of attention due to the increased research demand for deep space exploration around the world. But UTORAs have the disadvantages of easy oxidation and chalking. So, in this study, a UTORA was prepared by hot-press sintering on VZrHfNbTa (HEA) substrate coated with hafnium. The bonding mechanism, resistance to high-temperature oxidation, and hardness of the sample tests were carried out. The results show that zirconium in the matrix will diffuse into the hafnium coating during the high-temperature sintering process and form the HfZr alloy transition layer, the coating thickness of the composite is about 120 μm, and the diffusion distance of zirconium in the hafnium coating is about 60 μm, this transition layer chemically combines the hafnium coating and the HEA substrate into a monolithic alloy composite. The results of high-temperature oxidation experiments show that the oxidation degree of the hafnium-coated VZrHfNbTa composite material was significantly lower than that of the VZrHfNbTa HEA after oxidation in air at 1600 °C for 5 h. The weight gain of the coated sample after oxidation is 56.56 mg/cm2, which was only 57.7 % compared to the weight gain of the uncoated sample (98.09 mg/cm2 for uncoated), and the surface of the uncoated HEA showed obvious dents, oxidation, and pulverization occurred on the surface and interior of the sample. In contrast, the coated composite alloy sample mainly underwent surface oxidation sintering to form a dense HfO2 protective layer, and the internal oxidation of the hafnium-coated VZrHfNbTa composite alloy was significantly lower than that of the uncoated VZrHfNbTa HEA.

Bacterial phylogenetics has largely been determined via 16S rRNA gene sequencing and phylogenetic tree reconstruction. Observed utility of this approach has driven the popularity of the 16S rRNA gene amplicon metagenomics method for profiling and identifying diverse microbes from specific habitats. This work sought to develop universal primers for amplifying the 16S rRNA gene from a consortium of disparate microbial species. Using multiple sequence alignment of the 16S rRNA gene of a variety of microbes, the resulting highly conserved region of the consensus sequence was used for design of universal polymerase chain reaction (PCR) primers for 16S rRNA gene. Application of the universal primers in simulated PCR reveals poor amplification efficiency where only 12 species out of 31 generated an amplicon. BLAST analysis of the resulting amplicons reveals a classification error of 50%. More significantly, analysis of the amplicon length indicates variable read length ranging from 81 to 122 base pair compared to the predicted read length of 100 base pairs. This suggests that the 16S rRNA gene harbours significant hitherto underappreciated sequence diversity, and may have unknown alternative splicing and recombination mechanisms. Overall, results from this study suggests that primer design for 16S rRNA amplicon metagenomics may be application and habitat specific, where it is difficult to design universal primers for all bacterial species. Conceptually, this meant that there may be sequence co-evolution in 16S rRNA gene for microbial species in the habitat where environmental and nutritional conditions impact on 16S rRNA gene structure and sequence. In essence, 16S rRNA gene may habour epigenetics signals at the gene level.

Diamond powders with inclusions of europium atoms were synthesized at high pressure (7.7 GPa) and temperature (1800oC) from a mixture of pentaerythritol, C(CH2OH)4, and pyrolyzate of diphthalocyanine (C64H32N16Eu) served as a special precursor. In prepared diamonds by X-ray fluorescence spectroscopy, we have found the concentration of Eu atoms of 51±5 ppm that is by two orders of magnitude greater than that in known natural and synthetic diamonds. X-ray diffraction, SEM, X-ray exited optical luminescence, Raman and IR spectroscopy have confirmed the formation of diamond monocrystals of high quality with em-bedded Eu atoms and a nitrogen content of ~500 ppm. Numerical simulation has allowed us de-termine the energy cost of 5.8 eV needed for the incorporation of a single Eu atom with adjacent vacancy into growing diamond crystal (528 carbons).

Despite significant advances in metallurgy and the potential to create high and very high-strength steel, all international specifications for steel design provided little information about the limits of slenderness for high-strength steel sections (HSSs) and didn’t give anything about the design of very high-strength steel sections (VHSSs). The American structural steel design specification covers circular hollow sections (CHS) of steel grades up to S690, while it isn't in ANSI/AISC 360-16 and ASTM A514/A514M. Euro code EN 1993-1-1 can be applicable only to steel grades up to S460. EN 1993-1-3 and EN 1993-1-12 contain supplementary rules for cold-formed members and HSS (S460- S700), respectively. Though ductility requirements for (HSS) are specifically established in EN 1993-1-12, it is largely a continuation of the normal-strength-steel design procedures standardized in EN 1993-1-1, where (HSSs) are largely treated as normal-strength steels in these rules, and the same design approaches are used. The behavior of high and very high-strength steel circular hollow sections under axial compression load is studied in this research. A total of 16 nonlinear finite-element (FE) models were generated to replicate stub column tests that were experimentally tested by others in previous research. Hence, a parametric study is conducted using forty FE models developed to investigate the local buckling behavior under various slenderness ratios comprehensively. The developed models cover slenderness ratios ranging from 20 to 1226 and steel grades S460 and S1100 with yield stress equal 460 MPa and 1152 MPa, respectively. The FE results were combined with 105 previously collected experimental results to assess the applicability of existing codified design methodologies in the Euro code and the North American codes of cold-formed CHS. Based on the results of this study, new cross-sectional slenderness limits and new design equations for more efficient simple designs were presented for high and very-high strength steel circular hollow sections and Compared with the results of experimental tests and FE models.

High temperatures (HT) and high hydrostatic pressures (HHP) are characteristic of deep-sea hydrothermal vents and other deep crustal settings. These environments host vast and diverse microbial populations, yet only a small fraction of those populations have been successfully cultured. This is due, in part, to the difficulty of sampling while maintaining these in situ conditions and also replicating those high-temperature and high-pressure conditions in the laboratory. In an effort to facilitate more HT-HHP cultivation, we present two HT-HHP batch culture incubation systems for cultivating deep-sea vent and subsurface (hyper)thermophilic microorganisms. One HT-HHP system can be used for batch cultivation up to 110 MPa and 121°C, and requires sample decompression during subsampling. The second HT-HHP system can be used to culture microorganisms up to 100 MPa and 160°C with variable-volume, pressure-retaining vessels that negate whole-sample decompression during subsampling. Here, we describe how to build cost effective heating systems for these two types of high-pressure vessels, as well as the protocols for HT-HHP microbial batch cultivation in both systems. Additionally, we demonstrate HHP transfer between the variable-volume vessels, which has utility in sampling and enrichment without decompression, laboratory isolation experiments, as well as HHP filtration.

In the present study, the effect of melatonin and sodium nitroprusside treatments on the improvement of high temperature tolerance in California Wonder green bell pepper plant was studied. For this purpose, a factorial experiment was conducted in a form of a completely randomized design in three replications at Zabol University's Faculty of Agriculture. In this research, green bell pepper plants of Wonder cultivar were exposed to different temperature treatments (25°C, 35°C and 40°C) for 24 hours after being sprayed (foliar application) with 0μM, 50μM and 100μM concentrations of melatonin and sodium nitroprusside. Results showed that Shoot dry weight without fruit (DWPWF) at 40°C in compared to 25°C, 21.54% decreased. Also, foliar application with 100μM melatonin in compared to control (0uM) caused a 13.26% an increased in dry weight of shoots without fruit (DWPWF). Also, leaf chlorophyll at 40°C temperature in compared to 25°C temperature 32.82% decreased and foliar application with 100μM melatonin and 100μM sodium nitroprusside improved leaf chlorophyll value in compared to other foliar application treatments. Foliar application with 50uM and 100uM sodium nitroperoxide at 40°C temperature caused decreased of 15.16% and 20.99% of leaf hydrogen peroxide in compared to 0uM foliar application treatment, respectively. Also, under 40°C temperature, foliar application with melatonin and sodium nitroprusside (50μM and 100μM) in compared to 0μM foliar application activity of leaf superoxide dismutase enzyme increased. Also, leaf nitrogen under with 50 μM and 100μM melatonin in compared to 0μM foliar application 9.61% and 23.72% increased. Leaf potassium in 40°C temperature, foliar application with 50uM melatonin, 100uM melatonin, 50uM sodium nitroprusside and 100μM sodium nitroprusside 55.20, 72, 25.60 and 70.40% in compared to 0uM foliar application increased respectively. leaf iron in foliar application with 100μM sodium nitroprusside in compared to 0μM foliar application 17.96% increased.

Delineating chilling and forcing periods is one of the challenging topics in understanding how temperatures drive the timing of budburst and bloom in fruit tree species. Here, we investigated this question on olive trees, using flowering data collected over six years on 331 cultivars in the worldwide collection of Marrakech, Morocco. Using a Partial Least Squares approach on a long-term phenology (29 years) of ‘Picholine Marocaine’ cultivar, we showed that the relevance of delineating the chilling and forcing periods depends more on the variability of inter-annual temperatures than on the long-term datasets. In fact, chilling and forcing periods are similar between those delineated by using datasets of 29 years and those of only 6 years (2014–2019). We demonstrated that the variability of inter-annual temperatures is the main factor explaining this pattern. We then used the datasets of six years to assess the chill and heat requirements of 285 cultivars. We classified Mediterranean olive cultivars into four groups according to their chill requirements. Our results, using the Kriging interpolation method, indicated that flowering dates of most of these cultivars (92%) were governed by both chilling and forcing temperatures. Our investigations provided first insights to select adapted cultivars to global warming.

So far, scientific studies on high frequency welding (HF) have observed the three main parameters: anode current, welding time and pressure of upper electrode. Some authors have also observed and studied the welding frequency, the power, and the values of the dielectric constants of the materials or the angle of dielectric losses. Due to the complex effects that the parameters have on the quality of the welded joint, it is necessary to extend the research and study the mutual relationships between a large numbers of process parameters on the welded joint in order to achieve satisfactory strength of the welded joint. In this research, the number of considered parameters is increased to 17, each of which is relevant to the processes of HF welding, and their mathematical equations are presented. The research is carried out on a HF welding machine improved with a linear pneumatic actuator for lowering the upper electrode and regulating the compressive force, and a measuring machine with the appropriate measuring method for determining the breaking forces with a tension gage and performing the „T“ test is made. Numerous researches were carried out on the functional changes of the process parameters of the percentage share of the values of the coupling capacitor, the anode current and the welding time on the values of the breaking forces of the welded joints. Based on the conducted research, it was concluded that the optimization of the process parameters of HF machine must be performed before the welding process, which is determined by a certain amount of energy that must be introduced into the material. These parameters are the capacity of the output capacitor, i.e., the value of the electric current flowing through the material and the time for the development of the operating power to produce welded joints with a certain strength and quality of welded joints for a specific material used in the process.

SiC is a material with excellent mechanical and thermal properties, but with a high production cost. Obtaining SiC by reactive infiltration is an attractive method and at a much lower cost than the traditional sintering process. However, the reactive infiltration process presents a serious problem, which is the high residual silicon content, which decreases its range of application. The replacement of silicon with silicides is a widely used alternative. The present investigation shows the good mechanical properties of the SiC/IrSi₃ composite material obtained by reactive infiltration of SiC/C preforms with Ir-Si alloys. The thermomechanical analysis shows a high compatibility of silicide with SiC. The presence of the silicide shows a substantial improvement against the oxidation of the SiC/Si composites.

Multi-board electronic cases with high density and high power modules are widely used in industrial power supply management. With the improvement of case performance and miniaturization requirements, heat dissipation becomes one of the important factors to be considered in the design process. First,The existing small electronic thermal design methods focus on heat dissipation structure or heat source layout optimization,and ignores on-load test for modeling analysis. Second,The selected power module has on-load power consumption, resulting in relatively low calorific value and the effectiveness of thermal design cannot be verified. Third, The thermal lacks Intelligent monitoring and feedback control mechanism. In order to solve these problems, this paper designs a kind of heat dissipation case with intelligent temperature control based on high-power and high-density power supply array. Based on the extremely miniaturization design principle, we adopt the composite heat dissipation mode based on conduction and supplemented by forced air cooling . The case is made of magnesium and aluminum alloy with a perforated design. Finally, we compare and analyze with the existing cooling design. The results show that the case is smaller in volume, and the cooling performance parameters are slightly better than the existing case. Under the condition of high-density and high-power design, The output power of the whole system is not less than 10kw and the lowest packing-level density is not less than 47w/cm2 with high reliability, portability and practicability. It also provides technical support and prototype support for the standardized design of similar power arrays.

Nowadays, with the development of laser weapons, the primary power supply of laser weapons puts forward more and more high demand for its performance. The pulsed power supply based on conventional homopolar inductor alternator (HIA) cannot meet the requirements any more. In order to improve the power density and efficiency, this paper proposes applying the high-temperature superconducting (HTS) HIA with slotless stator core to this power supply. In this paper, the design considerations of it are presented, and the comparisons between the two power supplies are discussed. The calculation results show that the power supply based on HTS machine has much larger power density than the conventional HIA, and the efficiency is also larger than the conventional HIA. This can improve the performance of laser weapons dramatically.

In the present study, the effect of melatonin and sodium nitroprusside treatments on the improvement of high temperature tolerance in California Wonder green bell pepper plant was studied. For this purpose, a factorial experiment was conducted in form of a completely randomized design in three replications at Zabol University's Faculty of Agriculture. In this research, green bell pepper plants of Wonder cultivar were exposed to different temperature treatments (25°C, 35°C and 40°C) for 24 hours after being sprayed (foliar application) with 0μM, 50μM and 100μM concentrations of melatonin and Sodium nitroprusside. Results showed that Instantaneous leaf water consumption efficiency in 40°C temperature treatment with 50μM and 100μM melatonin increased. Also in 40°C temperature with 100µM melatonin, fruit dry weight in compared to control (0uM) 13.15% increased. Also, melatonin and sodium nitroprusside treatments in compared to control treatment improved fruit characteristics and reduced Appearance Characteristics of Fruit Marketability (ACFM) number. Under 40°C temperature treatment in compared to control temperature (25°C), fruit total soluble solids (TSS) 18.50% decreased also under 100μM melatonin treatment, fruit TSS 20.69% was increased compared to control treatment (0μM). Also fruit fructose at 40°C temperature in compared to 25°C temperature treatment 5.52% reduced. Fruit calcium at 35°C and 40°C temperature in compared to control temperature 6.96% and 15.65% decreased respectively. At temperature 35°C under foliar application of 100uM sodium nitroprusside, fruit copper in compared to control 28.93% increased.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

Our findings indicate that all five phytocannabinoids reduce HG-HL-induced -cell loss likely through reducing apoptosis and pyroptosis. The protective effects of CBD, THCV, CBC, and CBN were seen in the GSIS impairment by HG-HL. Although all five phytocannabinoids tested in this research demonstrated the capability to inhibit β-cell dedifferentiation induced by HG-HL, CBD seems to be more effective compared to the other phytocannabinoids, as indicated by the specific biomarker responses of β-cells and progenitor cells to CBD.

In order to create a smart mine, it is necessary to digitize the existing emulsion pumping station. Existing research does not achieve this task, this paper designs and manufactures a high-pressure, high-flow, high-water-based mining digital controlled unloading valve (abbreviated as HLHMDCUV), which achieves good results in both theoretical analysis and experimental testing. In order to obtain the accurate dynamic characteristics, this valve was analyzed by simulation using AMESim. Based on the dynamic performance analysis and the flow field analysis inside the valve body, the structure has been optimized to improve the performance of HLHMDCUV. The results show that the HLHMDCUV has a better dynamic characteristics, which were also demonstrated in the experiment. At the same time, the HLHMDCUV is easy to disassemble and maintain. This paper provides a theoretical basis for the design of such valves, which is conducive to the subsequent promotion of intelligent mine transformation.

High-quality rice (Oryza sativa L.) is increasingly widely planted in China with the improvement of people's living standards and the achievement of rice breeding efforts in recent years. However, the agronomic and physiological performances of high-quality indica rice (HQIR) under different nitrogen(N) application conditions in southern China are little known. Two-year consecutive field experiments were conducted with two HQIR and two ordinary-quality indica rice (OQIR) varieties under moderate and high N application rates, with yield and yield components, biomass, N up-take, and their related traits investigated. We found that grain yields of HQIR were slightly de-creased, but grain yields of OQIR were significantly increased by 6.60%-8.88% under high N rate compared with moderate N rate in both years. Thereby, OQIR produced 8.34%-11.87% and 22.00%-22.50% higher grain yield than HQIR under moderate and high N rates, respectively. The different responses of grain yield to N application rates were mainly due to decreased grain set-ting rate in HQIR and increased spikelets m-2 in OQIR under high N rate. Furthermore, high N rate significantly reduced pre-anthesis AE and improved grain-leaf area ratio, while did not in-crease post-anthesis DM compared with moderate N rate in HQIR, which might result in carbon metabolic deterioration and imbalance of source-sink relationship and subsequently lower supply of carbohydrate to panicle. Our results suggest that a moderate N rate (165 kg N ha-1) is beneficial for HQIR varieties to balance the maximum grain yield and high quality in southern China

Osteoarthritis of the hand (HOA) is one of the most common musculoskeletal diseases affecting health. Osteophytes, documented by imaging procedures are often used as diagnostic criteria. The gold standard is the radiographic image, however, more sensitive and saver methods such as ultrasound are gaining in importance. We investigated the prevalence, grade and pattern of osteophytes by high resolution ultrasound investigation (US) in a population-based cross-sectional study. Factory workers were recruited at work. 26 finger joints of each participant were examined with US with grading the occurrence of osteophytes in a semiquantitative score ranging 0-3, increasing scores indicated larger osteophytes. 427 participants (mean age 53.5 years, range. 20-79 years) were investigated, resulting in 11,000 scored joints. At least one osteophyte was found in 4,546/11,000 (41.3%) joints or 426/427 (99.8%) participants but grade 2 or 3 osteophytes were seen in only 553 (5.0%) joints. The number of os-teophyte sum score increased with age (0.18/year of age increase, p<0.001). Distal interphalange-al joints (DIP) were predominantly affected with 61%, followed by proximal interphalangeal joints (PIP) with 48%, carpometacarpal joint 1 (CMC1) with 39% and metacarpophalangeal joints (MCP) with 16%. In conclusion, US is a feasible screening tool for osteophytes and HOA. Grade 1 osteophytes are a common finding in the working population when assessed by ultrasound and their prevalence is increasing with age. Prevalence of grade 2 or 3 osteophytes is less common and reflects clini-cal presence of HOA. Follow up investigations are necessary to recognize the predictive rele-vance of early osteophytes.

Chitosan (CTS) is widely used in agriculture as a soil amendment, plant growth regulator and promoter of cold resistance. However, the effects of CTS on strawberry seedlings under the combined stress of high-temperature and high-light are unclear. In this study, Xuelixiang strawberry was used as a test material, and 100 mg·kg-1 CTS solution was sprayed onto the leaves. We measured the chlorophyll content, membrane peroxidation, reactive oxygen species content, antioxidant enzyme content, AsA-GSH cycle activity and other related indicators of strawberry seedling leaves under the combined stress of high-temperature and high-light and found that CTS can increase the contents of antioxidants, increase the contents of osmotic adjustment substances, increase the activity of antioxidant enzymes activity,; remove reactive oxygen species over time, reduce the damage of reactive oxygen species to photosynthetic organs and cell membranes, and improve the photosynthesis efficiency of leaves of strawberry plants under high-temperature and high-light stress, thereby reducing damage to strawberry seedlings caused by high-temperature and high-light.

Various types of electroconductive additives were evaluated for high C-rate capability in an attempt to extend practical application of high-areal-capacity lithium–sulfur batteries that employ an aluminum-foam current collector. Carbon nanofibers (CNFs) were found to be the most effective additive, with the ability to attain a high-sulfur-loading of 40 mg cm−2. A CNF-containing cell exhibited gravimetric capacities of 1094 and 758 mAh gsulfur−1 (46.8 and 32.4 mAh cm−2) at 0.05 and 0.1 C-rate, respectively, in an ether-based electrolyte. Because a CNF-containing slurry exhibits low viscosity even at a high solid ratio, it could be filled into the aluminum foam. Additionally, a lithium–sulfur battery with high-sulfur-loading had an energy density of ~120 Wh kg−1, a value that was calculated from the weight of the components of the cathode, anode, current collectors, electrolyte, and separator. Assuming that the amount of electrolyte decreases and that the energy density of cells accumulate, a theoretical energy density of 522 Wh kg−1 was estimated. Moreover, it was found that even if a high-areal-capacity was achieved, the discharge capacity converged at a high C-rate, unless there was an improvement in ion diffusion in the bulk electrolyte. This is considered a limitation of sulfur cathodes with high-sulfur-loading.

For 80 years high-intensity focused ultrasound (HIFU) has been a significant area for medical research. It is a non-invasive procedure which causes cell death in a highly localised area at a defined distance from the transducer. Since 2000, the clinical indications have broadened considerable as the technology has improved. This review looks back at the history of HIFU and the current clinical indications.

The objective was to estimate the correlation between VIs and grain yield and identify the optimal timing and VIs for precise corn grain yield estimation. Furthermore, the study aims to employ photographic quantification to measure corn ear traits and establish their correlation with corn grain yield. Ten corn hybrids were evaluated in CRB with three rep-lications at three locations. Vegetation indices and green leaf area were estimated throughout the cycle using an unmanned aerial vehicle (UAV) and subsequently corre-lated with grain productivity. In addition, photographs were taken of the corn ear to esti-mate their length, width and total number of kernels and compare these values with manual measurements. The experiments consistently demonstrated significant experi-mental quality across sites, with accuracy ranging from 79.07% to 95.94%. UAV flights carried out at the beginning of the crop cycle revealed a positive correlation between grain productivity and the evaluated indices (NGRDI, VARI, GLI). Regarding the phenotyping of corn ears, the regression coefficients for width, length and TNG were 0.92, 0.88 and 0.62, respectively, indicating an association with manual measurements. However, stage V5 in the localities of Lavras and Ijaci and stage V8 in the locality of Nazareno showed a posi-tive correlation with productivity. The use of images for ear phenotyping is promising as a method for measuring corn components.

Infrastructure and urban network operators, city users and industrialists are faced with complex issues to ensure the sustainability of the service, maintain, operate and develop their urban systems, while integrating environmental, economic and societal impacts and being resilient to unexpected geopolitical and climatic upheavals. Digital Twins are now recognized as the cornerstone of digital transformation. In the field of smart cities, they can enable all stakeholders to collaborate across disciplinary silos and foster digital transformation in urban and territorial projects to ensure sustainability, resilience and increased inventiveness. However, the application of the Digital Twin technology to Smart Cities lacks of standards. This paper proposes a high-level architecture for Digital Twins as an enabler of various levels of interoperation between key stakeholders of a Smart City. Such a technology-agnostic architecture, when implemented for a given Smart City, produces a middleware for large scale interoperability between actors involved in multiple supply chains of this territory.

Lunar seismology is a critical area of research, providing insights into the Moon's internal structure, composition, and thermal history, as well as informing the design of safe and resilient habitats for future human settlements. This paper presents the development of a state-of-the-art, three-axis broadband seismometer with a low frequency range of 0.001-1 Hz and a target sensitivity over an order of magnitude greater than previous Apollo-era instruments. The paper details the design, assembly, methodology and test results. We compare the acceleration noise of our prototype and commercial seismometers across all three axes. Increasing the test mass and reducing its natural frequency may further improve performance. These advancements in seismometer technology hold promise for enhancing our understanding of the Moon's and other celestial bodies' internal structures, and for informing the design of future landed missions to ocean worlds.

Wearable thermoelectric generators (w-TEGs) convert thermal energy into electrical energy to realize self-powering of intelligent electronic devices, thus reducing the burden of battery replacement and charging, and improving the usage time and efficiency of electronic devices. Through finite element simulation, this study successfully designed high-performance thermoelectric generator and made it into wearable thermoelectric module by adopting “rigid device - flexible connection” method. It was found that higher convective heat transfer coefficient on cold-end leads to larger effective temperature difference and better power generation performance of device in typical wearable scenario. Meanwhile, at same convective heat transfer coefficient on the cold-end, longer TE leg length leads to larger temperature difference established at both ends of device, larger device output power and open-circuit voltage. However, when the convective heat transfer coefficient increases to a certain level, optimization effect of increasing TE leg length on device power generation performance will gradually diminish. For devices with fixed temperature difference between two ends, longer TE leg length leads to higher resistance of TEG, resulting in lower device output power but slight increase in open-circuit voltage. Finally, sixteen 16×4×2 mm2 TEGs (L=1.38 mm, W=0.6 mm) and two modules were fabricated and tested. At hot end temperature Th=33 ℃ and cold end temperature Tc=30 ℃, the actual maximum output power Pout of TEG is about 0.2 mW, and the actual maximum output power Pout of TEG module is about 1.602 mW, which is highly consistent with the simulated value. This work brings great convenience to research and development of wearable thermoelectric modules and provides new, environmentally friendly and efficient power solution for wearable devices.

UHPC is a type of cement-based composite used in new construction and/or rehabilitation of existing buildings to extend service life. It is a novel composite material that can serve as an alternative to concrete construction in hostile climates. Following decades of study and production, a diverse variety of commercial UHPC compositions are now available globally to meet the rising number of applicants and demand for high-quality building materials. Although UHPC offers major benefits over normal concrete, its utilization is restricted due to restrictive design rules and exorbitant costs. As a result, a thorough examination of the durability properties of UHPC is required to give important information for material testing requirements and processes, as well as to broaden its practical uses. This report is aimed at increasing basic understanding of UHPC and supporting more UHPC research and applications.

One of the intriguing recent results in the field of high-entropy alloys is the discovery of single-phase equiatomic multi-component Laves intermetallics. However, there is no clear understanding that a combination of chemical elements will form such high-entropy compounds. Here we contribute to understanding this issue by modifying the composition of duodenary TiZrHfNbVCrMoMnFeCoNiAl (12x) alloy in which we recently reported the fabrication of hexagonal C14 Laves phase. We consider three alloys based on 12x: 7x=12x-VCrMoMnFe, 12x+Sc, 12x+Be and observe that all of them crystalize with the formation of C14 Laves phase as a dominant structure. We report that 12x+Be alloy reveals single-phase C14 structure with very high concentration of structural defects and ultra-fine dendritic microstructure with almost homogenous distribution of the constituted elements over the alloy matrix. The 7x and 12x+Sc alloys contain C14 as a main phase and unknown impurity phases. To characterize the materials, we examine their heat capacity, electrical conductivity and magnetic properties. The measurements reveal that the Laves phases are Curie-Weiss paramagnets, which demonstrate metallic conduction; 7x and 12x alloys also reveal a pronounced Kondo-like anomaly. Analysis of experimental data as well as ab initio calculations suggests that chemical complexity and compositional disorder cause strong s-d band scattering and thus the rather high density of d-states in the conduction band. Analysis of the results suggests that the mechanism of Laves phase formation in multicomponent multi-principal element metallic alloys is may be the same as in polydisperse hardspheres mixtures. Another important conclusion is that the configurational entropy is a negligible factor in the stabilization of multi-element Laves phases.

The interaction of electrons with strong laser fields is usually treated with semiclassical theory, where the laser is represented by an external field. There are analytic solutions for the free electron wave functions, which incorporate the interaction with the laser field exactly, but the joint effect of the atomic binding potential presents an obstacle for the analysis. Moreover, the radiation is a dynamical system, the number of photons changes during the interactions. Thus, it is legitimate to ask how can one treat the high order processes nonperturbatively, in such a way that the electron-atom interaction and the quantized nature of radiation be simultaneously taken into account? An analytic method is proposed to answer this question in the framework of nonrelativistic quantum electrodynamics. As an application, a quantum optical generalization of the strong-field Kramers-Heisenberg formula is derived for describing high-harmonic generation. Our formalism is suitable to analyse, among various quantal effects, the possible role of arbitrary photon statistics of the incoming field. The present paper is dedicated to the memory of Prof. Dr. Fritz Ehlotzky, who had significantly contributed to the theory of strong-field phenomena over many decades.

Many real complex systems present multilayer structure where high-order metadata on one layer refers to dyadic data on a lower layer. Significant progresses to analyse high-order metadata under the assumption of community organization have been done. However, there are no planted communities in real-world networks, and the necessity of new frameworks to analyze high-order metadata regardless of community organization has been raised.Here, we propose to adopt hyperedge organization. Predicting ‘entanglements’ between a hyperedge and nodes scattered in the rest of the network might suggest structural or functional liaisons, without assumption of any community organization. We introduce a novel concept: hyperedge entanglement (HE), which associates to each hyperedge an entangled hyperedge, by means of a network operator that predicts significant ‘interactions at distance’ between network nodes and existing hyperedges. We also introduce a new challenge termed hyperedge entanglement prediction (HEP), and an algorithm to perform this task. We evaluated HEP performance on social, biological and synthetic data where, given only topology and hyperedges (such as communities or functional modules), the goal is to predict whether nodes not connected to a certain hyperedge might be candidates for a significant entanglement. Finally, as real application in diseasome systems biomedicine, we perform HEP on the human protein interactome to predict unknown gene entanglements with the COPD disease gene hyperedge. HEP predictions are validated by biological experiments, enlarging our understanding of molecular mechanisms behind COPD/aneurysm comorbidity.

This paper presents a numerical algorithm for solving high-order BVPs. We introduce the construction method of multiscale orthonormal basis in W^m[0; 1] by multiscale orthonormal basis in W¹[0; 1]. We define approximate solution, and obtain the approximate solution of high-order BVPs by using the approximate theory. Moreover, the convergence and stability of the algorithm are improved. At last, several numerical experiments show the feasibility of the proposed method.

The nondestructive testing of reinforced concrete chimneys, especially the high ones, is an important element of the assessment of their condition, making it possible to forecast their safe service lifespan. Industrial chimneys are often exposed to the strong action of acidic substances – they are adversely affected by the flue gas condensate on the inside and by acid precipitation on the outside. Initially, this results in the corrosion of the shell concrete and then in the corrosion of the reinforcing steel. During the service life of such chimneys their condition should monitored in order to prevent structural failures and indicate the most endangered parts of the structure. Owing to thermographic surveys one can monitor the hazards leading to the degradation of the chimney structure, which is particularly vital when due to the character of the production process the chimney cannot be put out of operation. The methods for the interpretation of results from thermovision studies to determine the safety and durability of industrial chimneys are shown.

High throughput multiplex serological systems enable the small developer to set up tests at small cost, for microbes for which there are no commercial tests, and for aspects which have not been addressed by them. An example is testing for Zika and Tick Borne Encephalitis virus antibodies, where antigenic cross-reactions make diagnosis problematic. Our technique variant, Suspension Multiplex Immunoassay (SMIA) allows many samples to be tested for antibodies to many antigens in a short time. Computational compensation for cross-reactions is possible if a SMIA panel contains most of the potentially cross-reacting antigens. Using antibody avidity and pattern of reactivity to whole virus and nonstructural protein, antibodies due to vaccination and infection, respectively, as well as probable degree of protection, can be determined with high throughput. These multiplex techniques hold great promise for future diagnostic development. Theoretically, even large scale serological monitoring, like blood donor pathogen testing, could be done inexpensively and rationally with multiplex serology developed in house. However, the quality control demands are steep and in most cases out of scope for a single laboratory. There remain however a number of clinical applications where in house multiplex serology can be performed with adequate quality control under high throughput conditions.

Local air quality is a major concern for the population regularly exposed to high levels of air pollution. The airport, mainly due to its aircraft engines activities during taxiing and take off, is often submitted to heterogeneous but important concentrations of NOx and PM. The study suggests an innovative approach to determine the air traffic impact on air quality at the scale of the airport, its runways and terminals, in order to be able to locate the persistent high concentrations spots. The pollutants concentrations at 10 m resolution and 1 s time step are calculated in order to identify the most affected areas of an airport platform. A real day of air traffic on a regional airport is simulated, using real data as aircraft trajectories (from radar streams). In order to estimate the aircraft emissions, the Air Transport Systems Evaluation Infrastructure (IESTA) is used. Regarding local air quality, IESTA relies on the non-hydrostatic meso-scale atmospheric model Meso-NH using grid-nesting capabilities with 3 domains, for this study. The detailed cartography of the airport distinguishes between grassland, parking and terminals, allowing to compute exchanges of heat, water and momentum between the different types of surfaces and the atmosphere as well as the interactions with the building using a drag force. The dynamic parameters like wind, temperature, turbulent kinetic energy and pollutants concentration are computed at 10 m resolution over the 2 × 4 km airport domain. The pollutants are considered in this preliminary study as passive tracers, without chemical reactions. This preliminary study aims at proving the feasibility of high scale modelling over an airport with state of the art physical models.

Celecoxib as adjuvant therapy has been shown in a small randomized trial for Covid-19 to prevent clinical deterioration and rapidly improve thoracic computerized axial tomography (CT-chest)¹. Multiple descriptive trials of high dose famotidine (both inpatient and outpatient) have demonstrated clinical response^2,3,4. We describe the rapid clinical responses after increasing the celecoxib dosage to 400mg bid with high dose famotidine 80mg qid in both a critical inpatient who on baseline required 40 liters per minute high flow nasal insufflation and an outpatient who declined admission but had critical Covid-19 biomarkers.

Prolonged ethanol (EtOH) consumption is associated with male infertility with a decreased spermatogenesis rate as one cause. Defective maturation and development of sperm during their storage in the cauda epididymis and transit in the seminal vesicle can be another cause, possibly occurring before the drastic spermatogenesis disruption. Herein, we demonstrated that the cauda epididymis and seminal vesicle of rats, orally fed with EtOH under a regimen that spermatogenesis was still ongoing, showed histological damage, including lesion and decreased height of the epithelial cells, and increased collagen fibers in the muscle layer, which implicated fibrosis. Lipid peroxidation (shown by malondialdehyde (MDA) levels) was observed, indicating that reactive oxygen species (ROS) was produced along with acetaldehyde during EtOH metabolism by CYP2E1. MDA, acetaldehyde and other lipid peroxidation products could further damage cellular components of the cauda epididymis and seminal vesicle and this was supported by increased apoptosis (shown by TUNEL assay and caspase 9/caspase 3 expression) in these two tissues of EtOH-treated rats. Consequently, functionality of the cauda epididymis and seminal vesicle in EtOH-treated rats was impaired, as demonstrated by decreases in 1H NMR-analyzed metabolites (e.g., carnitine, fructose), which were important for sperm development, metabolism and survival in their lumen.

The gas-water relative permeability curve plays a crucial role in reservoir simulation and development for condensate gas reservoirs. In this study, we conducted a series of high temperature and high pressure analysis experiments on real gas cores from Wells A and B in Block L of the Yinggehai Basin to investigate the effects of temperature, pressure, and different types of gas media on gas-water seepage. The experimental results demonstrate that: Temperature has a significant impact on both gas and water relative permeability, particularly on the former. As temperature increases, gas relative permeability shows a substantial increase while water relative permeability remains relatively unchanged. Under the same effective stress, increasing pressure causes downward shifts in both the gas and water relative permeability curves; however, there is a more pronounced decrease in gas relative permeability. Gas type has minimal influence on phase permeability except at higher water saturation where differences become apparent. When water saturation ranges from 80% to 50%, there is no significant variation observed in the measured relative permeability of different displacement gases; however, as water saturation exceeds 80%, distinctions gradually emerge. At bound water saturation conditions, nitrogen exhibits lower relative permeability compared to simulated gases with approximately 92% similarity between them. This investigation into the characteristics of gas-water relative permeability in high temperature and high pressure condensate reservoirs within Yinggehai Basin provides valuable insights for efficient development strategies for similar reservoirs.

The current pneumonia epidemic could evolve into a pandemic on a global scale if not effectively contained. The COVID-19 virus possesses a 61-amino acid open reading frame resembling SARS-CoV virulence factor - ORF6 peptide. The isoleucine content is 15.9% in ORF6 of SARS-CoV versus 16.4% of that in SARS-CoV-2. Given the proton affinity in the carbonyl oxygen in isoleucine, augmented proton traffic can enhance proton-ion antiport and prompt cell swelling. Calorie restriction has been confirmed in animal studies to extend lifespan, and its underlying mechanism is not fully known. As the content of essential amino acids in the open reading frame of SARS-CoV-2 reaches 57.4%, a starch/vitamin diet served for short period of time does not give rise to essential amino acids and halts virion production, which could be adopted as prophylactic approach of many viral infections. Plant-based diet or fasting/boiled rice water can also minimize the intake of essential amino acids or all amino acids respectively. Furthermore, several proteins of SARS-CoV-2 possess high valine plus glycine content which is implicated in heart disease, justifying the aforementioned approaches.

The present study examined and compared the effects of high- and low-molecular weight (MW) chitosan, a nutraceutical, on intestinal and liver lipid metabolism in rats fed with high-fat diet. Both high- and low-MW chitosan decreased liver weight, elongated small intestine, improved the dysregulation of blood lipids and liver fat accumulation, and increased fecal lipid excretion in high-fat diet-fed rats. Supplementation of both high- and low-MW chitosan significantly inhibited the decreased phosphorylated AMP-activated protein kinase (AMPK)α and peroxisome proliferator-activated receptor (PPAR)α protein expressions and the increased lipogenesis/cholesterogenesis-associated protein expressions (sterol regulatory element binding protein (SREBP)1c, SREBP2, and PPARγ) and the decreased apolipoprotein (Apo)E and microsomal triglyceride transfer protein (MTTP) protein expressions in the livers of high-fat diet-fed rats. Both high and low-MW chitosan supplementation could also suppress the increased MTTP protein expression and the decreased angiopoietin-like protein (Angptl)4 protein expression in the intestines of high-fat diet-fed rats. Comparison between high and low-MW chitosan, high-MW chitosan has a higher efficiency than low-MW chitosan on the inhibition of intestinal lipid absorption and the increase of hepatic fatty acid oxidation, which can improve liver lipid biosynthesis and accumulation.

Students have historically fared poorly on the West African Examinations Council’s (WAEC) mathematics exam. This study investigated senior high school students’ difficulties with studying Geometry in the Cape Coast Metropolis, Central Region, Ghana. Using the descriptive survey design, data were collected from 300 Senior High School Two (SHS 2) students using simple random sampling. Students responded to the questionnaire and a 30-item multiple-choice achievement test on geometry. Four geometry concepts students perceived difficult to study are Circle theorems, Perpendicularity of Tangent and radius of a circle, Angle between Tangent and a chord and Tangents from an external point. The reasons for the difficulty in studying geometry topics are the unavailability of instructional materials, the geometry topics being complex, and teachers not teaching geometry concepts to the students’ understanding. Students’ gender did not influence the learning of concepts in geometry at a 0.05 level of significance. There was an insignificantly weak positive correlation between the students’ performance and their perceived difficult geometry concepts. It was concluded that the Ministry of Education does not provide relevant instructional materials to the various schools to teach geometry concepts. Schools do not organise workshops and seminars for teachers on effectively teaching geometry concepts in mathematics.

This paper presents the experimental campaign conducted near the Condoroma dam at 4075 m a.s.l. in an experimental setup consisting of a series of standard profile spillways with a vertical upstream face of up to five different dimensionless heights (P/Hd). The experimental results indicate that for all P/Hd ratios studied, the discharge coefficients adjusted to the Condoroma altitude are lower than those reported by classical formulations used in conventional spillway design. As a result, a generalized equation is proposed to estimate the discharge coefficient for standard spillways located in dams at similar elevations above sea level.

Vibrations of plate structures placed in a supersonic flow is considered. The undisturbed fluid flow is parallel to the plate. Two specific problems are treated: in the first one the plate is in the form of an infinite strip and the flow is in the direction of its finite length. Rigid walls extend from the sides of the plate indefinitely. In the second problem, the plate is a finite rectangle and the flow is parallel to one of its sides. The first problem is a limiting case of the second problem. The flow is modeled by piston theory which assumes that the fluid pressure on the plate is proportional to local slope. This approximation is widely used at high speeds, and reduces the interaction between the fluid flow and the vibrations of the plate to an additional term in the vibration equation. The resulting problem can be solved by assumed mode methods. In this study, the solution is also carried out by using the collocation method. The main result is the flutter velocity of the free fluid flow under which the plate vibrations become unstable. Finally, simple expressions are proposed between the various non-dimensional parameters that allows quick estimation of flutter velocity.

For a comprehensive exploration of the Bimolecular Fluorescence Complementation (BiFC) approach, we critically assess whether protein pairs establish direct or indirect interactions within this context. Emphasizing the multifaceted nature of protein interactions, this review underscores the imperative of delineating macromolecular complex characteristics across five distinct levels: composition, stoichiometry, copy number, topology, and dynamics. A pivotal discussion revolves around the challenges introduced by the overexpression of target proteins and the potential artificial ramifications of fusion proteins. The significance of stoichiometry in protein interactions is illuminated, with the HOXA9/PBX1 interaction serving as a pertinent case study. The research identifies and elaborates on the inherent limitations of prevailing large-scale BiFC screenings, advocating for the incorporation of rigorous negative controls. A novel proposition is introduced in the form of a high-throughput multicolor BiFC strategy, exemplified using the HOXA9 and PBX1 proteins. The paper culminates with an insightful discourse on the implications of tags within the BiFC system, presenting the TriFC (Tripartite Fluorescence Complementation) assay as a promising alternative.

High-dimensional measurement error data are becoming more prevalent across various fields. Research on measurement error regression models has gained increasing attention due to the risk of drawing inaccurate conclusions if measurement errors are ignored. When the dimension p is larger than the sample size n, it is challenging to develop statistical inference methods for high-dimensional measurement error regression models due to the existence of bias, nonconvexity of objective function, high computational cost and many other difficulties. Over the past few years, some works have overcome the aforementioned difficulties and proposed several statistical inference methods. This paper mainly reviews the current development on estimation, hypothesis testing and variable screening methods for high-dimensional measurement error regression models and shows the theoretical results of these methods with some directions worthy of exploring for future research.

Sepsis is a major health problem and accounts for 20 per cent of deaths worldwide. It is the most expensive condition treated in United States hospitals at $27 billion per year or about $20,000 per patient. Treatment consisting largely of fluid resuscitation and antibiotics has only marginal impact. Mortality is about 27 per cent for hospitalized patients and about 42 per cent for patients in intensive care.There are two phases of sepsis – a hyper inflammatory phase and a subsequent hypo inflammatory phase.During the hyper inflammatory phase the metabolic rate increases associated with an increase in body temperature and a rapid escalation of immune system functioning including increased numbers of leucocytes and migration of those leucocytes to infected and damaged tissues and an increased supply and consumption of glucose to fuel this immune system.During the subsequent hypo inflammatory phase the metabolic rate declines and this is associated with a decrease in body temperature and a generalized decrease in the physiological activity of many organs including the immune system akin to hibernation. The activated immune system has priority for the available glucose over most other organs and physiological functions during such potentially life threatening circumstances. Thus adenosine triphosphate (ATP) production by mitochondria (the source of energy at the cellular level for the organism as a whole) also has a lower priority for the available glucose relative to the activated immune system. If glucose availability is threatened then mitochondrial production of ATP is partially or substantially suppressed in favor of glycolysis because glycolysis can rapidly produce large quantities of ATP that are necessary for immune cell function in infected, anaerobic, ischemic, or damaged tissues.However, glycolysis is only a temporary fix as it cannot produce the quantities of ATP necessary on an ongoing basis for the normal functioning of the healthy animal. Mitochondrial production of ATP must be recommenced for full recovery.It appears that the partial or substantial suppression of mitochondrial production of ATP by activation of the immune response becomes relatively fixated in some patients leading to a substantial ATP deficit. This is the fundamental issue of sepsis.This paper reviews the metabolism of glucose and insulin during sepsis and concludes that high dose insulin with mild hyper glycaemia in conjunction with the intravenous administration of thiamine, an inhibitor of the pyruvate dehydrogenase kinase enzymes, to re-establish physiological ATP production by mitochondria, administered early in the hypo metabolic (hypo inflammatory) phase of sepsis should significantly improve survival.

Abstract: The high entropy alloy (HEA) of equiatomic composition CrNiFeCoMn and with FCC 11 crystal structure was prepared by either induction melting and additive manufacturing with a se- 12 lective laser melting (SLM) process, starting from mechanically alloyed powders. Unlike induction 13 melting, the as-produced SLM alloy showed fine nitride and Cr-rich s phase precipitates. Mechan- 14 ical spectroscopy measurements were performed on specimens cold worked and/or recrystallized. 15 Young’s modulus values of (140±10) GPa and (90±10) GPa were measured at 300 K for induction 16 melted and SLM samples, respectively. The values increased to (160±10) GPa and (170±10) GPa for 17 recrystallized samples. Damping measurements as a function of temperature showed two peaks 18 which were attributed to dislocations bending and grain boundaries sliding. The peaks were super- 19 posed on a temperature increasing background.

Many studies in the field of robot navigation have focused on environment representation and localization. The goal of map representation is to summarize spatial information in topological and geometrical abstracts. By providing strong priors, maps improve the performance and reliability of automated robots. Due to the transition to fully automated driving in recent years, there has been a constant effort to design methods and technologies to improve the precision of road participants and the environment's information. Among these efforts is the High Definition (HD) Map concept. Making HD maps requires accuracy, completeness, verifiability, and extensibility. Because of the complexity of HD mapping, it is currently expensive and difficult to implement, particularly in an urban environment. In an urban traffic system, the road model is at least a map with sets of roads, lanes, and lane markers. While more research is being dedicated to mapping and localization, a comprehensive review of the various types of map representation is still required. This paper presents a brief overview of map representation, followed by a detailed literature review of HD Map for automated vehicles. The current state of AV mapping is encouraging, the field has matured to a point where detailed maps of complex environments are built in real-time and have been proved useful. Many existing techniques are robust to noise and can cope with a large range of environments. Nevertheless, there are still open problems for future research. AV mapping will continue to be a highly active research area essential to the goal of achieving full autonomy.

UHPC is a cement-based composite that is used in new construction and/or renovation of existing structures to increase their service life. It is a unique composite material that may be used as an alternative to concrete in harsh conditions. Following decades of research and development, a wide range of commercial UHPC compositions are now accessible across the world to fulfill the growing number of applications and demand for high-quality construction materials. Although UHPC has significant advantages over conventional concrete, its use is limited because of rigid design restrictions and excessive pricing. As a consequence, a detailed analysis of UHPC's durability qualities is necessary to provide critical information for material testing requirements and methods, as well as to widen its practical applications. The goal of this study is to learn more about UHPC and to encourage more research and use of UHPC.

Infective endocarditis remains an illness that carries a significant burden to healthcare resources. In recent times, there has been a shift from Streptococcus sp to Staphylococcus sp as the primary organism of interest. This has significant consequences given the virulence of Staphylococcus and its propensity to form a biofilm, rendering non-surgical therapy ineffective. In addition, antibiotic resistance has affected treatment of this organism. The cohorts at most risk for Staphylococcal endocarditis are the elderly patients with multiple comorbidities. The innovation of transcatheter technologies alongside other cardiac interventions such as implantable devices have contributed to the increased risk attributable to this cohort. We examine the role of the heart team for diagnosis and treatment of this condition. In addition, we examine the determinants of virulence of Staphylococcus aureus, the interaction with hosts immunity and the discovery and emergence of a potential vaccine. We also examine the potential role of prophylactic antibiotics during dental procedures. With increasing rates of transcatheter device implantations, there is a projected increment of endocarditis especially in this high-risk group. A high index of suspicion is needed alongside early initiation of therapy and referral to the heart time to improve outcomes.

We communicate the theoretical results in the study of utilizing the quantum phenomena in optical current for quantum computation in the context of high precision voltage measurements. These results can be used around computation by quantum sampling and quantum communication as the basis for further research and physical implementations. We propose a Main Optical Setup (MOS) for such computation which allows to make a superstructure to implement specific computations and algorithms. To create MOS we used the nonlinear units (e.g., beta- barium borate crystal), arranged in series, powered with pulsed laser pump, and ended with the beam splitter to generate the output state of a number of entangled photon pairs. The computation is made by propagation of entanglement with beam splitters applied crossword and adjustable phase shifters that are tools for parameter steering. We show how to implement the series of cosine-based components on the example of two-component case. The results opens a broad area for future research in the area of building quantum optimizer using the quantum sampling methods and in the area of high precision temporal measurement of voltage, which is the important process for building high-fidelity devices.

Selective laser melting (SLM) is a commonly used laser powder bed technique where the final properties are influenced by many different powder related properties, such as particle size distribution, chemical composition and flowability. In applications where high hardness, wear resistance, strength and good heat properties are required, high speed steels (HSS) are widely used today. HSS has high carbon content and are therefore considered as unweldable. The rapidly growing implementation of AM technologies has led to a growing range of new applications and demands for new alloys and properties. The interest in being able to manufacture HSS by SLM without cracking is therefore increasing. In SLM, it is possible to preheat the base plate to a few hundred degrees Celsius which has been used for HSS and proved successful due to reduced thermal gradients. In this study, the properties of SLM produced high speed steel PEARL Micro®2012 with a carbon content of 0.61 wt.-% have been investigated and compared to those of a forged and rolled PM-HIP counterpart ASP®2012.

Optical artificial neural networks (ONNs) — analog computing hardware tailored for machine learning [1,2] — have significant potential for ultra-high computing speed and energy efficiency [3]. We propose a new approach to architectures for ONNs based on integrated Kerr micro-comb sources [4] that is programmable, highly scalable and capable of reaching ultra-high speeds. We experimentally demonstrate the building block of the ONN — a single neuron perceptron — by mapping synapses onto 49 wavelengths of a micro-comb to achieve a high single-unit throughput of 11.9 Giga-FLOPS at 8 bits per FLOP, corresponding to 95.2 Gbps. We test the perceptron on simple standard benchmark datasets — handwritten-digit recognition and cancer-cell detection — achieving over 90% and 85% accuracy, respectively. This performance is a direct result of the record small wavelength spacing (49GHz) for a coherent integrated microcomb source, which results in an unprecedented number of wavelengths for neuromorphic optics. Finally, we propose an approach to scaling the perceptron to a deep learning network using the same single micro-comb device and standard off-the-shelf telecommunications technology, for high-throughput operation involving full matrix multiplication for applications such as real-time massive data processing for unmanned vehicle and aircraft tracking.

Methods of path integrals are used to develop multi-factor probabilities of bid-ask variables for use in high-frequency trading (HFT). Adaptive Simulated Annealing (ASA) is used to fit the nonlinear forms so developed to a day of BitMEX tick data. Maxima algebraic code is used to develop the path integral codes into C codes, and sampling code is used for the fitting process. After these fits, the resultant C code is very fast and useful for forecasting upcoming ask, bid, midprice, etc., when narrow and wide windows of incoming data are used. A bonus is the availability of canonical momenta indicators (CMI) useful to forecast direction and strengths of these variables.

The expression "Follow the water" is used in order to recognize inside the universe, life as it exists on Earth. It is shown here that the expression "Follow the water in its high-subcritical state" can be used in order to recognize the components of life which form prior to the emergence of life. This specific state of water leaves signatures inside the minerals which are produced during high-subcritical water/rock interaction.

Polymer-derived SiC-polycrystalline fiber (Tyranno SA) shows excellent heat-resistance up to 2000^oC, and relatively high strength. Up to now, through our research, the relationship between the strength and residual defects of the fiber, which were formed during the production processes (degradation and sintering), has been clarified. In this paper, we addressed the relationship between the production condition and the surface roughness of the obtained SiC-polycrystalline fiber, using three different raw fibers (Elementary ratio: Si₁Al_0.01C_1.5O_0.4~0.5) and three different types of reactor (Open system, Partially-open system, and Closed system). With increase in the oxygen content in the raw fiber, the degradation during the production process easily proceeded. In this case, the degradation reactions (SiO+2C=SiC+CO and SiO₂+3C=SiC+2CO) in the inside of each filament become faster, and then the CO partial pressure on the surface of each filament is considered to be increased. In consequence, according to Le Chatelier’s principle, the surface degradation reaction and grain growth of formed SiC crystals would be considered to become slower. That is to say, using the raw fiber with higher oxygen content and closed system (highest CO content in the reactor), much smoother surface of the SiC-polycrystalline fiber could be achieved.

In this paper, a novel integrated high precision vacuum microelectronic accelerometer is put forward based on the theory of field emission, the accelerometer consists of sensitive structure and interface ASIC. The sensitive structure has a mass of a cathode cone tips array, a folded beam, an emitter electrode and a feedback electrode. The sensor is fabricated on a double side polished (1 0 0) N-type silicon wafer, the tips array of cathode are shaped by wet etching with HNA (HNO3, HF and CH3COOH) and metalized by TiW/Au thin film. The structure of sensor is released by ICP process finally. The interface ASIC was designed and fabricated based on the P-JFET high voltage bipolar process. The accelerometer is tested through static field rollover test, and the test results show the integrated vacuum microelectronic accelerometer has good performances, which sensitivity is 3.081V/g and non-linearity is 0.84% in the measuring range of −1g~1g.

High redshift blazars are among the most powerful objects in the Universe. Although they represent a significant fraction of the extragalactic hard X-ray sky, they are not commonly detected in gamma-rays. High redshift (z>2) objects represent <10 per cent of the AGN population observed by Fermi so far, and gamma-ray flaring activity from these sources is even more uncommon. The characterization of the radio-to-gamma-ray properties of high redshift blazars represents a powerful tool for the study of the energetics of such extreme objects and the Extragalactic Background Light. This contribution will present results of multi-band campaigns, from radio to gamma-rays, on PKS 0836+710, PKS 2149-306, and TXS 0536+145. The latter is the highest redshift detection of a flaring gamma-ray blazar so far. At the peaks of their respective flares these sources reached an apparent isotropic gamma-ray luminosity of about 10^50 erg/s, which is comparable with the luminosity observed from the most powerful blazars. The physical properties derived from the multi-wavelength observations of these sources are then compared with those shown by the high redshift population.

Aqueous Zinc ion batteries (ZIBs) possess significant potential in large energy storage systems due to their cost-effectiveness and environmental protection. However, the limited voltage window and poor reaction kinetics of the cathode material are still bottlenecks, restricting the further development of ZIBs. In this work, we rationally design Ni-doped V2O5@3D Ni core/shell composite on carbon cloth electrode (Ni-V2O5@3D Ni@CC) by growing Ni-V2O5 on the free-standing 3D Ni metal nanonets for high-voltage and high-capacity ZIBs. Impressively, the embedded Ni doping increases the interlayer spacing of V2O5, extending the working voltage and improving the Zn2+ kinetics reaction of the cathode materials, at the same time the 3D structure with high specific surface area and superior electronic conductivity benefits to fast Zn2+ transport. Consequently, the as-designed Ni-V2O5@3D Ni@CC cathodes can operate within a wide voltage window from 0.3 to 1.8 V vs. Zn/Zn2+ and deliver a high capacity of 270 mAh g-1 at a high current density of 0.8 A g-1. In addition, the reversible Zn2+ (de)-incorporation reaction mechanisms in the Ni-V2O5@3D Ni@CC cathodes are investigated by multiple characterization methods. As a result, we achieve a big step toward the practical applications of commercial ZIBs.

The poor oxidation resistance of refractory high-entropy alloys (RHEAs) is a major obstacle for their use in high-temperature engineering applications. Anti-oxidation coating technology is an effective method for improving the oxidation resistance. In this paper, the Si-20Cr-20Fe coating was prepared on MoNbTaTiW RHEA by a fused slurry method. The microstructural evolution and compositions of the silicide coating under high-temperature oxidation environment were studied. The results show that the silicide coating could effectively prevent the oxidation of the MoNbTaTiW RHEA. The initial silicide coating had a double-layer structure; a high silicon-content layer mainly composed of MSi2 as the outer layer and a low silicon-content layer mainly contained M5Si3 as the inner layer. Under high-temperature oxidation conditions, the silicon element diffused from the silicide coating to the RHEA substrate while the oxidation of the coating occurred. After oxidation, the coating was composed of an outer oxide layer and an inner silicide layer. The silicide layer moved toward the inside of the substrate, led to the increase of its thickness. Compared with the initial silicified layer, its structure did not change significantly. The structure and compositions of the oxide layer on the outer surface strongly depended on the oxidation temperature. This paper provides a strategy for protecting RHEAs from oxidation at high-temperature environments.

In this paper, the stabilization and high efficiency of an unstable Second Harmonic Generation (SHG) of a Nd : YVO4 laser with a KTP intracavity is carried out by using a passive Q-switching crystal and a parametric modulation method (harmonic modulation) is shown. The harmonic modulation was defined as um(t) = Amsin(2π fmt), with modulation amplitude as Am(Vpp), and modulation frequency as fm(Hz), applied to the pumping of the Nd : YVO4 -KTP laser to control the amplitude and frequency of the emission, thus stabilizing the dynamic states of this laser. The promising application of this green light source is materialized when such light is necessary for high-density optics, such as in the treatment materials industry or in some aesthetic applications.

The use of renewable fuels for internal combustion engines marks a significant stride towards sustainability in transportation and power generation. Ensuring the compatibility of these fuels with existing diesel engines and infrastructure is paramount for a smooth transition. Diesel engines ca-pable of harnessing the advantages of alternative fuels without extensive modifications offer a pragmatic approach to sustainable power for vehicles and industries. This article investigates the impact of carbon neutral renewable fuel types (HVOs and biodiesel) on the operation of the high-pressure injection pump, focusing on rotational speed and delivery pressure as key parame-ters. Investigations, based on pump operating cycle analysis and volumetric efficiency measure-ments, reveals that while speed dependence is moderate, fuel type significantly influences pump performance. Hydrogenated carbon-neutral fluids (HVOs) demonstrate adequate capabilities compared to conventional fossil fuels, offering promising prospects for reducing environmental impact. The findings underscore the importance of considering fuel properties, particularly com-pressibility modulus. These insights provide valuable guidance for the advancement of sustainable transportation and industrial systems.

High temperature (HT) geothermal wells can provide green power 24h a day 7 days a week. Harsh environmental and operational conditions, long-term durability requirements of such wells require special cementitious composites for well construction. This paper reports a comprehensive assessment of geothermal cement composites in cyclic pressure function laboratory tests, field exposures in an HT geothermal well (300-350oC) as well as a numerical model to complement the experimental results. Performances of calcium-aluminate-cement (CAC)-based composites and calcium free cement were compared against reference Ordinary Portland Cement (OPC)/silica blend. The stability and degradation of the tested materials was characterized by crystalline composition, thermo-gravimetric, and elemental analyses, morphological studies, water-fillable porosity, and mechanical properties measurements. All CAC-based formulations outperformed the reference blend both in the function and exposure tests. The reference OPC/silica lost its mechanical properties during the 9-month well exposure through extensive HT carbonation, while properties of the CAC-based blends improved over that period. The Modified Cam-Clay (MCC) plasticity parameters of several HT cement formulations were extracted from triaxial and Brazilian tests and verified against the experimental results of function cyclic tests. These parameters can be used in well integrity models to predict field-scale behavior of the cement sheath under geothermal well conditions.

High gravity brewing (HGB) and adjunct use are common practices in industrial breweries. This work studied the impact of HGB and wheat adjuncts on beer characteristics. Parameters were evaluated in full-malt beer and beers prepared with 30 % wheat grits (WG) and wheat flakes (WF) in the grist and the effect of HGB was examined. Five beers were prepared; one control, two with different original gravity (OG) with WF and two with WG. Beers with higher OG were diluted to a lower OG and control beer was prepared too. The application of wheat adjuncts increased foam stability but HGB did not affect the beer foam. HGB beers had a remarkably higher ester concentration than other samples, and beers with WG also had a significantly higher ester content. Decreased higher alcohols to esters ratio in HGB beers affected the balanced flavour profile of the lager beer. There was a significantly lower content of unwanted volatiles such as vicinal diketones and dimethyl sulphide in HGB beers. The application of HGB mostly did not affect the beer ageing characteristics such as carbonyl compounds and thiobarbituric acid number.

Significant advances in Penning trap measurements of atomic masses and mass ratios of the proton, deuteron, triton, helion, and alpha-particle have occurred in the last five years. These include a measurement of the mass of the deuteron against 12C with 8.5 x 10-12 fractional uncertainty; resolution of vibrational levels of H2+ as mass and the application of a simultaneous measurement technique to the H2+/D+ cyclotron frequency ratio, yielding a deuteron-proton mass ratio at 5 x 10-12; new measurements of HD+/3He+, HD+/T+ and T+/3He+ leading to a tritium beta-decay Q-value with an uncertainty of 22 meV, and atomic masses of the helion and triton at 13 x 10-12; and a new measurement of the mass of the alpha-particle against 12C at 12 x 10-12. Some of these results are in strong disagreement with previous literature values. Their impact in determining a precise proton/electron mass ratio and electron atomic mass from spectroscopy of the HD+ molecular ion is also discussed.

For both conventional and renewable energy conversion processes, computational fluid dynamics (CFD) has been used to address more energy-related challenges in recent decades. Using CFD to investigate vertical-axis wind turbines has become more common in recent years. The main goals of this application have been to more accurately predict the turbine's performance and to comprehend the complicated nature of the complex turbulent flow. The Vertical Axis Wind Turbine (VAWT) simulation for energy-generating applications has several intricate components. One of them is being aware of the chaotic flow that occurs during the first stages of the starting process, which influences overall effectiveness. In this article, the performance of the wind turbine was increased by using a passive flow control approach. The numerical research was carried out using Large Eddy Simulation for four alternative tip speed ratios in both cases, the classic and the optimized, equipped with a vortex trap on the exterior of the blades. The power and torque coefficient variations, as well as the velocity magnitude contours, show that the starting process may begin with a significant improvement in efficiency when flow control is used.

Spray technology is widely used in various industries, including medicine, food production, mechanical engineering, and nanopowder manufacturing. Achieving high dispersion and a narrow particle size distribution is crucial for many applications. Ultrasonic spraying is commonly used to achieve this. On other hand, hydraulic nozzles provide high atomization performance. Combining these two technologies promises to offer significant benefits, but the complex processes that occur simultaneously in such a device require careful study. This work proposes a fundamental design for an acoustic-hydraulic nozzle and investigates the physical processes when a liquid is sprayed using this nozzle, both theoretically and experimentally. The study identifies the critical modes of spraying and confirms that the simultaneous use of ultrasound and hydraulic pressure can produce a fine spray (droplet size less than 50 μm) with high productivity (5-10 ml/s). This approach has significant potential for modern industries and technologies.

This study presents a comprehensive investigation of the formation, composition, and behaviour of oxide layers during the high-temperature oxidation of four different steel alloys (16Mo3, 13Cr, T24 and P91) at a uniform temperature of 650 °C. The research combines CALPHAD (CALculation of PHAse Diagrams) calculations, thermogravimetric analysis (TGA) and advanced microscopy techniques, including scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), to elucidate the complex mechanisms controlling oxidation kinetics and oxide layer development. CALPHAD calculations were used to determine the thermodynamically stable phases for each steel type at 650 °C. The results showed different phase compositions, highlighting the importance of steel composition in the formation of oxide layers. Each steel grade exhibited different kinetics, with 16Mo3 steel showing the highest oxidation rate, followed by 13Cr, T24 and P91. This variability highlights the role of steel composition, particularly chromium content, in determining oxidation behaviour. These results have significant implications for temporary overheating in industrial applications and contribute to a deeper understanding of oxidation processes in steels.

Germanium (Ge) nanostrip is embedded in polymer and studied as a waveguide. Measurement reveals that this new type of semiconductor/polymer heterogeneous waveguide exhibits strong absorption for the TE mode from 1500 nm to 2004 nm, while the propagation loss for the TM mode declines from 20.56 dB/cm at 1500 nm to 4.89 dB/cm at 2004 nm. The transmission characteristics serves as an essential tool to verify the optical parameters (n-κ) of the thin strips, addressing to the ambiguity raised by spectroscopic ellipsometry regarding highly absorbing materials. Furthermore, the observed strong absorption for the TE mode at 2004 nm is well beyond the cut-off wavelength of the crystalline bulk Ge (~1850 nm at room temperature). This redshift is modeled to manifest the narrowing of the Tauc-fitted bandgap due to the grain order effect in the amorphous Ge layer. The accurate measurement of the nanometer-scale light-absorbing strips in a waveguide form is a crucial step toward the accurate design of integrated photonic devices that utilize such components.

AgW materials exhibit excellent properties and are widely used as contact materials in low- and medium-voltage switches. In this study, a pre-sintering and infiltration method was employed to pre-sinter W powder with Cu, Ni, and (Cu+Ni) addition in the low temperature range of 950–1050 °C. The low-temperature sintering behaviours of W skeletons with different additives were investigated. Subsequently, AgW70, AgW75, AgW80, and AgW85 materials were prepared through infiltration at 1050 °C. The microstructure morphology and physical properties of high-W contact materials were investigated using a metallographic microscope and scanning electron microscope. The mechanism of low-temperature sintering-infiltration of high-W contact materials was elucidated. The results indicated that pure W and 1% Cu-added W skeletons experience minimal linear shrinkage within the temperature range of 950–1050 °C. The linear shrinkage curves of W skeletons with different additives coincided under the conditions of 950–1000 °C/90 min. At 1050 °C, after sintering for 150 min, the particle boundaries in the W skeleton were fully spheroidised, with a dihedral angle of 120°. At 1050 °C and after 150 min of infiltration, cross-sectional micrographs of the AgW material revealed the presence of irregular Ni layers, where Ni spatially enveloped/encapsulated Ag. With an increase in the W content, the electrical conductivity and relative density of AgW(70–85) materials decreased, whereas the hardness of the materials increased.

Co-Zr amorphous alloys exhibit soft magnetic properties, whereas Co-rich crystalline magnetic phases in this alloy system display hard magnetic behaviour. In this study, an initial two-phase Co-Zr composite with an overall composition of 75 at.% Co and 25 at.% Zr was processed by high pressure torsion (HPT) and the effects of severe plastic deformation and subsequent thermal treatment on the structural evolution and its magnetic properties have been investigated. HPT processing allowed us to achieve an amorphous microstructure in the as-deformed state with low coercivity. To further tune magnetic properties and study the alloys’ crystallization behaviour, various annealed states are investigated. Microstructural properties are correlated to the magnetic properties and a decreasing coercivity with increasing annealing temperature is observed despite the onset of crystallization in the amorphous alloy. At higher annealing temperatures, coercivity increases again. The results appear promising to obtain tuneable rare-earth free magnetic materials by severe plastic deformation.

With the rapid and continuous advancement and deployment of advanced energy storage de-vices, there has been significant interest in aqueous capacitors that possess non-flammable properties and high safety features. Consequently, extensive research efforts have focused on investigating zinc anodes and low-cost carbonaceous cathode materials. Despite these efforts, the development of high-performance zinc-ion capacitors (ZICs) still faces challenges such as limited cycling stability and low energy densities. In this study, we present a novel approach to address these challenges. We demonstrate the utilization of a three-dimensionally (3D) grown conductive porous carbon framework cathode coupled with zinc anode cells, which exhibit exceptional sta-bility and durability in ZICs. Our experiments reveal a remarkable cycling performance, with a capacity retention of approximately 97.3% and a coulombic efficiency of nearly 100% even after 10,000 charge-discharge cycles. These findings signify significant progress in enhancing the performance of ZICs.

Clinching is a manufacturing method of mechanical joining two or more materials without the use of heat or additional components. This process relies on high plastic deformation to create a secure bond. Clinching technology is widely used for joining various grades and thickness of materials. Especially in the automotive industry, clinching is an alternative to spot resistance welding. However, the load-bearing capacity of clinched joints is comparatively lower when compared to resistance spot welded joints. This research aimed to enhance the load-carrying capacity of clinched joints. Experimental tests were conducted on clinched joints with locally modified microstructures to optimize their placement within the joint. The microstructure distribution in the clinched joint region was analysed using light and scanning electron microscopy, as well as microhardness measurements. Two material grades, micro-alloyed steels HX420LAD+Z and dual-phase ferritic-martensitic steels HCT600X+Z, were tested. Each grade underwent five groups of ten samples, subject to identical experimental conditions of local heating by resistance spot welding (RSW) and clinching. The application of RSW to the clinched joint area resulted in increase of load-bearing capacity for both joined types of materials.

This paper presents a comprehensive study and the analysis of a topology of a no isolated DC-DC intituled Double Quadratic Boost converter with high static gain. This converter has the main advantage of high static gain and low voltage stress on its switches. The article will first present the theoretical analysis of the converter operating in an open loop. The objective of the work is the mathematical modeling and the control strategy of the converter, as well as the validation through closed-loop experimental results. Besides, we presented the practice test results to demonstrate the operation of the converter, such as the static gain experimental curve, the practice efficiency of the converter, and the control of the output voltage, as well as the capacitor voltage balance control. The authors designed a prototype for 1 kW, with a switching frequency of fs=50kHz, with FPGA-based command and modulation.

Supplementary cementitious materials (SCMs) are increasingly used in precast concrete industry to enhance concrete strength and durability. SCMs of large market share in precast concrete in-dustry include silica fume, also known as micro-silica and class C fly ash. The main objective of this research is to develop non-proprietary high strength concrete mixes for precast/prestressed concrete industry. Two SCMs are used simultaneously in partial replacement of portland cement to develop ternary mixes. Class c fly ash and silica fume incorporation in the mix design, in ad-dition to low water-to-powder ratio resulted in the successful development of high strength mixes with minimum 24-hour strength in excess of 70 MPa and a final compressive strength ex-ceeding 100 MPa at 28 days. Mechanical properties testing of developed concrete mixes showed that SCMs incorporation resulted in increased values for hardened concrete modulus of elasticity (MoE) and modulus of rupture (MoR). The enhanced concrete properties, mainly high early strength, are highly required in precast concrete industry as it allows for increased productivity of precast facilities and the possibility of pouring high strength slender sections for prestressed concrete applications

Nowadays the practice of developing algorithms to maintain the confidentiality of data shows that there is a lack of some features, such as velocity, predictability, etc. Generating pseudorandom numbers is one such problem that lies in the basement of many algorithms, even in hardware microprograms. An unreliable generator can cause cyberattacks on it, despite the security in the upper layers. At the same time, the algorithm should be fast enough to provide uninterrupted circuit work for the entire system. The paper presents a new algorithm generating pseudorandom numbers on cellular automata, which is not only fast and easy-repeating, but unpredictable enough and can be used in cryptographic systems. Using the NIST statistical test suite for random and pseudorandom number generators (PRNG), it is shown that the presented algorithm is more than three times superior to the state-of-the-art methods and algorithms in terms of ? − ?????. A high level of the presented algorithm’s parallelization allows for implementation it effectively on calculators with parallel structure. CPU-based architecture, FPGA-based architecture, CUDA- based architecture of PRNG and different PRNG implementations are presented to confirm high performance of the proposed solution.

SiC ceramics are excellent materials applied at high temperatures because of their light weight, excellent high temperature strength, and high thermal shock resistance. For better engineering properties, we made SiC with fractal lattices. Stress-strain behavior and modulus changes from room temperature to 1,250oC were analyzed using LAMMPS S/W, a molecular dynamics program. As a result of this study, it was confirmed that the modulus of elasticity of SiC crystals changed in the range of about 475 GPa to 425 GPa as it increased from room temperature to 1,250 oC, The stress-displacement characteristics of SiC crystals, which could not be measured at a high temperature of 1,000 oC or higher, could be ensured.

During the few years, various algorithms have been developed to extract features from high-resolution satellite imagery. For the classification of these extracted features, several complex algorithms have been developed. But these algorithms do not possess critical refining stages of processing the data at the preliminary phase. Various satellite sensors have been launched such as LISS3, IKONOS, QUICKBIRD, and WORLDVIEW etc. Before classification and extraction of semantic data, imagery of the high resolution must be refined. The whole refinement process involves several steps of interaction with the data. These steps are pre-processing algorithms that are presented in this paper. Pre-processing steps involves Geometric correction, radiometric correction, Noise removal, Image enhancement etc. Due to these pre-processing algorithms, the accuracy of the data is increased. Various applications of these pre-processing of the data are in meteorology, hydrology, soil science, forest, physical planning etc. This paper also provides a brief description of the local maximum likelihood method, fuzzy method, stretch method and pre-processing methods, which are used before classifying and extracting features from the image.

As a critical transmitter, the compact 532 nm lasers operating on high repetition and narrow pulse widths have been used widely for airborne or space-borne laser active remote sensing. We developed a free space pumped TEM₀₀ mode sub-nanosecond 532 nm laser that occupied a volume of less than 125 mm × 50 mm × 40 mm (0.25 liters). The fundamental 1064 nm laser consists of a passively Q-switched composite crystal microchip laser and an off-axis, two-pass power amplifier. The pump sources were two single-emitter semiconductor laser diodes (LD) of 808 nm with a maximum continuous wave (CW) power of 10 W each. The average power of fundamental 1064 nm laser was 1.26 W with the laser operating at 16 kHz repetition rates, and 857ps pulse widths. Since the beam distortion would be severe in microchip lasers in terms of the increase in heat load, for obtaining a high beam quality of 532 nm, the beam distortion was compensated by adjusting the distribution of pumping beam in our experiment of fundamental amplification. Furthermore, better than 0.6 W average power, 770 ps, beam quality of M² ＜1.2, and 16 kHz pulse output at 532 nm was obtained by a Type I LiB₃O₅ (LBO) crystal in the critical phase matching (CPM) regime for second harmonic generation (SHG).

This work is driven by a practical question, corrections of Artificial Intelligence (AI) errors. Systematic re-training of a large AI system is hardly possible. To solve this problem, special external devices, correctors, are developed. They should provide quick and non-iterative system fix without modification of a legacy AI system. A common universal part of the AI corrector is a classifier that should separate undesired and erroneous behavior from normal operation. Training of such classifiers is a grand challenge at the heart of the one- and few-shot learning methods. Effectiveness of one- and few-short methods is based on either significant dimensionality reductions or the blessing of dimensionality effects. Stochastic separability is a blessing of dimensionality phenomenon that allows one-and few-shot error correction: in high-dimensional datasets under broad assumptions each point can be separated from the rest of the set by simple and robust linear discriminant. The hierarchical structure of data universe is introduced where each data cluster has a granular internal structure, etc. New stochastic separation theorems for the data distributions with fine-grained structure are formulated and proved. Separation theorems in infinite-dimensional limits are proven under assumptions of compact embedding of patterns into data space. New multi-correctors of AI systems are presented and illustrated with examples of predicting errors and learning new classes of objects by a deep convolutional neural network.

In this research paper, a high gain transformer less inverter modeling which is used for the smart grid technology or as the stand alone for home appliances is proposed. The proposed transformer less topology provides a higher voltage gain, low cost, small size and simple control stand alone transformer less inverter for home appliances. The above inverter is modeled by using software which is known as MATLAB/ Simulimk.

Background: global longitudinal strain (GLS) measures myocardial deformation and is a sensitive modality for detecting subclinical myocardial dysfunction and predicting cardiac outcomes. The accuracy of speckle-tracking echocardiography (STE) is dependent on temporal resolution. A novel software enables relatively high frame rate (Hi-FR) (~200 fps) echocardiographic images acquisition which empowers us to investigate the impact of Hi-FR imaging on GLS analysis. The goal of this pilot study was to demonstrate the feasibility of Hi-FR for STE. Methods: In this prospective study, we acquired echocardiographic images using clinical scanners on patients with normal left ventricular systolic function using Hi-FR and conventional frame rate (Reg-FR) (~50 FPS). GLS values were evaluated on apical 4-, 2- and 3-chamber images acquired in both Hi-FR and Reg-FR. Inter-observer and intra-observer variabilities were assessed in Hi-FR and Reg-FR. Results: There were 143 resting echocardiograms with normal LVEF included in this study. The frame rate of Hi-FR was 190 ± 25 and Reg-FR was 50 ± 3, and the heart rate was 71 ± 13. Strain values measured in Hi-FR were significantly higher than those measured in Reg-FR (all p < 0.001). Inter-observer and intra-observer correlations were strong in both Hi-FR and Reg-FR. Conclusions: We demonstrated that strain values were significantly higher using Hi-FR when compared with Reg-FR in patients with normal LVEF. It is plausible that higher temporal resolution enabled the measurement of myocardial strain at desired time point. The result of this study may inform clinical adoption of the novel technology. Further investigations are necessary to evaluate the value of Hi-FR to assess myocardial strain in stress echocardiography in the setting of tachycardia.

Abstract: Abstract: The objective of this article is to analyze the dimensions of creativity concerning students with high abilities. Firstly a review of the most relevant scientific contributions on creativity is carried out. Next the dimensions of creativity in secondary school students who have been previously identified as high- ability students are analyzed. Those abilities associated to di-vergent thinking were assessed by means of the Torrance Test of Creative Thinking [19]. The flu-ency, flexibility and originality dimensions were assessed with the Scientific-Creative Thinking Test (TPCC, [7]). The results obtained evidence that high-ability students achieve greater scores in both the figurative creativity and scientific-creativity dimensions. A significant relationship between creativity and high ability can therefore be established. This study is of an exploratory nature and the results obtained contribute to develop future studies in application of its findings in the teaching-learning process..

Over two years (2012-2014), 719 nasopharyngeal samples were collected from 6 weeks to 12 months old infants presenting at emergency department with moderate to severe acute bronchiolitis. Viral testing was performed and we found 98% positive samples including 90% Respiratory Syncytial Virus, 34% Human Rhino Virus, and 55% viral co-detections with predominance of RSV/HRV co-infections (30%). Interestingly, we found that the risk of being infected by HRV is higher in the absence of RSV, suggesting interferences or exclusion mechanisms between these two viruses. Conversely, Coronavirus infection had no impact on the likelihood of co-infection involving HRV and RSV. Bronchiolitis is the leading cause of hospitalizations in infants before 12 months of age, and many questions about its role in the later chronic respiratory diseases (asthma and chronic obstructive pulmonary disease) do exist. Role of virus detection and burden of viral codetections need to be further explored, in order to understand the physiopathology of chronic respiratory diseases, a major public health issue.

Due to the high solar irradiance or energy price, certain regions in the U.S. may reach 100% PV penetration and experience degradation of frequency response greater than the interconnection as a whole. Therefore, in this section, the 100% PV penetration region in each interconnection is simulated to study the local high PV penetration effects. The study was performed by quantifying RoCoF, frequency nadir, and settling frequency at different regional PV penetration levels. The impact of high regional PV penetration on the compliance of grid code on frequency response is also studied.

To improve the voltage gain of step-up converters, cascaded technique is considered as a possible solution in this paper. By considering the concept of cascading two Z-source networks in a conventional boost converter, the converter takes the advantages of both impedance source and cascaded converters. However, by applying some modifications, the proposed converter provides high voltage gain while the voltage stress of switch and diodes are still low. Moreover, the low input current ripple of the converter makes it absolutely appropriate for photovoltaic applications in order to expand the lifetime of PV panels. After analyzing the operation principles of the proposed converter, simulation and experimental results of a 100W prototype are presented to verify the proposed converter performance.

New hybrid nanostructured electrodes for supercapacitors made by combination of electrical double layer and faradaic supercapacitors based-nanomaterials within a single hybrid composite has a great potential on expanding the range of use of these devices and increase their electrochemical performance. In this work, we developed several hybrid nanostructured composites with combinations of such types of materials with potential applicability as electrodes in supercapacitors. In particular, these composites were obtained by easy, cost-effective and scalable procedures, and were composed by NiCo2O4 nanocores as the main faradaic-based nanomaterial and either the conductive polymer polyaniline (PANI), multiwall carbon nanotubes (MWCNTs), or reduced graphene oxide (r-GO) as the electrical double layer-based carbonaceous-based nanomaterials in order to enable the combination of both type of energy storage processes within a single nanostructured device. These constructions allowed us to obtain specific capacitance as large as 1760 F/g, 900 F/g and 734 F/g at a current density of 1 A/g for NiCo2O4/PANI, NiCo2O4/MWCNT, and NiCo2O4/r-GO hybrid nanocomposite electrodes, respectively. Besides, the stability of NiCo2O4/MWCNTs and NiCo2O4/r-GO-based electrodes was outstanding, with capacity losses below 10% after long periods of operation (> 500 cycles).

In this work we present the results obtained with an artificial neural network (ANN) which we trained to predict the expected output of high-order harmonic generation (HHG) process, while exploring a multi-dimensional parameter space. We argue on the utility and efficiency of the ANN model and demonstrate its ability to predict the outcome of HHG simulations. In this case study we present the results for a loose focusing HHG beamline, where the changing parameters are: the laser pulse energy, gas pressure, gas cell position relative to focus and gas cell length. The physical quantity which we predict here using ANN is directly related to the total harmonic yield in a specified spectral domain (20-40 eV). We discuss the versatility and adaptability of the presented method.

Micro-plasma is generated in ultra-high-pure hydrogen gas filled inside a cell at a pressure of (1.08 ± 0.033) × 10⁵ Pa (810 ± 25 Torr) by using a Q-switched Nd:YAG laser device operated at 1064 nm wavelength and 14 ns pulse duration. Micro-plasma emission spectra of the hydrogen Balmer alpha line, H_α, are recorded with a Czerny-Turner type spectrometer and an intensified charge-coupled device. The spectra are calibrated for wavelength and corrected for detector sensitivity. During the first few tens of nanoseconds after initiating optical breakdown, significantly Stark-broadened and Stark-shifted H_α lines mark the well-above hypersonic outward expansion. The vertical diameters of the spectrally resolved plasma images are measured for time delays of 10 ns to 35 ns to determine expansion speeds of the order of 100 km/s to 10 km/s. For time delays of the order of 0.5 µs to 1 µs, the expansion decreases to the speed of sound of 1.3 km/s in the near ambient temperature and pressure hydrogen gas.

We demonstrate for the first time efficient mechanical to electrical energy conversion using InGaN/GaN nanowires (NWs). Using an atomic force microscope equipped with a modified Resiscope module, we analyse the piezoelectric energy generation of GaN NWs and demonstrate an important enhancement when integrating in their volume a thick In-rich InGaN insertion. The piezoelectric response of InGaN/GaN NWs can be tuned as a function of the InGaN insertion thickness and position in the NW volume. The energy harvesting is favoured by the presence of a PtSi/GaN Schottky diode which allows to efficiently collect the piezo-charges generated by InGaN/GaN NWs. Average output voltages up to 330 ± 70 mV and a maximum value of 470 mV per NW has been measured for nanostructures integrating 70 nm-thick InGaN insertion capped with a thin GaN top layer. This latter value establishes an increase of about 35% of the piezo-conversion capacity in comparison with binary p-doped GaN NWs. By considering these output signals, we estimate a maximum power density generated by one layer of dense InGaN/GaN-based NW of about 3.3 W/cm². These results settle the new state-of-the-art for piezo-generation from GaN-based NWs and offer a promising perspective for extending the performances of the piezoelectric sources.