The analysis and simulation of water quality in distribution networks is a complex issue of great concern today. The analysis of the evolution of water age, as a simple indicator of water quality in the network, is of great interest in both design and operation phases. Understanding the factors that have the strongest influence on water quality is key to developing adequate strategies aimed at preserving it. This paper firstly analyses the factors with biggest influence in the tanks water age, to support the selection of the most appropriate configuration from the point of view of water quality during design phases. Then, the main considerations when modelling tanks following the different mixing models considered in Epanet have been presented. Also, a real tank behaviour has been characterised through field measurements and Epanet simulations in order to determine the best fitted mixing model.

The analysis presented is based on actual GHU energy demand. The special feature of this load is the existence of strong daily fluctuations in energy consumption, especially during the summer months. This study presents a methodology for managing such loads with the main objective of maximizing the operating efficiency of MG.

Underground storage of natural gas has the characteristics of clean and low-carbon, and has the ability to provide sustainable and stable supply. It is a very high-quality green energy that can increase the storage efficiency of gas storage through fracturing, achieving the sustainable development goal of "Carbon Peaking and Carbon Neutrality". The accurate evaluation of the fracability of a reservoir is an important prerequisite for reservoir fracturing design and post fracturing productivity evaluation. At present, research on fracability is mainly based on qualitative characterization or quantitative evaluation based on rock mechanics and fracturing construction parameters, which cannot fully reflect the rock composition and structure of each stage. Firstly, based on logging data, this paper analyzes the evolution laws of strain energy such as elastic properties, pre-peak dissipation energy, and post-peak fracture energy during the transition of rock materials from plastic deformation to brittle fracture in an energy perspective, and determines the key energy that affects the brittle characteristics of rocks. Secondly, a brittleness index evaluation approach has been established that can comprehensively reflect the mechanical properties of rocks during pre-peak deformation and post-peak damage stages. In addition, this article focuses on the impact of reservoir stratigraphic environment by combining the influence of geo-stresses with the rock brittleness index, and proposes a new method for evaluating reservoir fracability. Finally, this paper conducts a study on the fracability evaluation of three wells in a gas storage facility in eastern China. The results indicate that low modulus and fracability coefficient are beneficial for fracturing, thereby improving the gas production and peak shaving ability of gas storage.

: The primary use of the potato is direct consumption. The classification of potatoes into consumption type is made on the basis of consumption evaluation of hydrothermally treated tubers. Nutrient deficiency in the soil, including Mg, contributes to the inhibition of potato growth and development and negatively affects the cooking characteristics of the tubers. Magnesium and biostimulants are responsible for plant nitrogen management. Thus, it is necessary to control the content of harmful nitrates and toxic nitrites in tubers. In potato production, it is also important to maintain appropriate conditions during storage. The purpose of this study was to determine the effect of mineral fertilization with magnesium and a biostimulant preparation during cultivation of edible potato and long-term storage on the traits determining utility-consumption type and the content of harmful nitrogen compounds in tubers. The study was conducted using the early potato variety Satina. In a three-year (2015-2017) three-factor experiment: evaluation date (immediately after harvest and after six months of storage), soil fertilization with mineral magnesium (0, 30, 60, 90 kg MgO ha-1), application of an amino acid biostimulant (0, 1.5, 3.0 l ha-1), five consumption traits of tubers after cooking determining the utility-consumption type of potato were determined. In addition, the consumer safety of the potato was determined based on the nitrate and nitrite content of the tubers. The tendency to overcook tubers significantly depended on all the factors used during potato cultivation. In contrast, the texture and structure of tuber flesh after cooking depended only on mineral fertilization with magnesium. The flesh of the tubers after cooking was most tender (1.0 pt) and firm (1.4 pt) after the application of 60 and 90 kg MgO ha-1, respectively. The moisture level of the flesh after cooking was significantly influenced by the interaction of magnesium fertilization with the biostimulant preparation. The factors of the experiment did not modify the utility-consumption type (B/A), while there was a change in the type in relation to that specified by the grower - general utility (B). The applied cultivation technology and long-term storage did not deteriorate the consumer safety of tubers (<200 mg kg-1) in terms of NO3 (max. 112.1 mg kg-1) and NO2 (max. 1.08 mg kg-1) contents. Organoleptic traits: mealiness, moisture and flesh structure were significantly positively related to nitrate and nitrite content of tubers immediately after harvesting and to nitrite concentration after long-term storage.

Seed quality is crucial for the success of crop production, as it affects germination capacity, emergence potential, and seedling growth. This study investigated the impact of extended stor-age on the germination capacity, oleoresin and essential oil contents of black cumin seeds from three black cumin varieties in Ethiopia: "Aden", "Dershaye", and "Darbera". Seeds were stored for up to three years, and germination studies were conducted using a Completely Randomized De-sign. Results showed that storage period significantly affected various germination parameters, with a decrease in germination percentage observed with increasing storage period. However, variety and the interaction between storage period and variety had no statistically significant effect on germination percentage. The study also provides valuable insights into the correlations between different germination indices. Additionally, as black cumin seeds age, their oleoresin and essential oil contents decrease across all three varieties. Proper seed storage practices are essential in maintaining the germination potential of black cumin seeds, particularly over ex-tended storage periods. Overall, this study provides insights into the impact of extended seed storage on black cumin seed quality and germination potential, highlighting the importance of proper seed management practices to support sustainable crop production.

The paper addresses the ongoing and continuous interest in photovoltaic energy systems (PESs). In this context, the study focuses on an isolated photovoltaic system with hybrid bat-tery-supercapacitor storage (HBSS). The integration of supercapacitors (SCs) in this system is of particular importance because of their high specific power density. In photovoltaic (PV) systems, multi-storage systems use two or more energy storage technologies to enhance system perfor-mance and flexibility. When batteries and supercapacitors are combined in a PV system, their benefits are maximized and offer a more reliable, efficient, and cost-effective energy storage op-tion. In addition, effective multi-storage power management in a PV system needs a solid grasp of the energy storage technologies, load power demand profiles, and the whole system architecture. In this work, battery-supercapacitor storage system (HBSS) is established by combining batteries and supercapacitors. The primary objective is to devise a novel management algorithm that ef-fectively controls the different power sources. The algorithm's purpose is to regulate the charge and discharge cycles of the HBSS, ensuring that the state of charge (SOC) of both batteries and supercapacitors remains within the desired range. The proposed management algorithm is de-signed to be simple, efficient, and light on computational resources. It efficiently handles the energy flow within the HBSS, optimizing the usage of both batteries and supercapacitors based on real-time conditions and energy demands. By maintaining the SOC of these energy storage components within the specified limits, the proposed method ensures their longevity and max-imizes their performance. Simulation results obtained from applying the management strategy are found to be satisfactory. These results show that the proposed algorithm maintains the SOC of batteries and supercapacitors within the desired range, leading to improved energy management and enhanced system efficiency.

A new study for CH4 reforming to hydrogen and hydrogen storage was performed using magnesium-based alloy. MgH2-12Ni (with the composition of 88 wt% MgH2 + 12 wt% Ni) was prepared in a planetary ball mill by milling in hydrogen atmosphere (reaction-involved milling). X-ray diffraction (XRD) analyses were performed for the samples after reaction-involved milling and after reactions with CH4. The variation of adsorbed or desorbed gas with time was measured by a Sieverts’ type high-pressure apparatus at 773 K. The microstructures of the powders were observed using scanning transmission microscope (STEM) with energy-dispersive X-ray spectroscopy (EDS). The synthesized samples were also characterized using Fourier Transform Infrared (FT-IR) spectroscopy. XRD pattern of MgH2-12Ni after reaction with CH4 of 12 bar at 773 K and decomposition under 1.0 bar at 773 K exhibited phases of MgH2 and Mg2NiH4. This shows that reforming of CH4 was occurred, hydrogen produced after reforming of CH4 was then adsorbed on the particles, and hydrides were formed during cooling to room temperature. Ni and Mg2Ni formed during heating up to 773 K are believed to have brought about catalytic effects for reforming CH4. MgH2-12Ni adsorbed 0.8 wt% reformed CH4 within 1 min in a reaction with CH4 of 12 bar at 773 K and then desorbed 0.8 wt% reformed CH4 (hydrogen-containing mixture) within 1 min under 1 bar at 773 K. Attenuated total reflectance FT-IR spectroscopy (ATR-FTIR) spectra of MgH2-12Ni after reactions under 12 bar CH4 at 723 K and 773 K showed peaks of C-H bending, C=C stretching, O-H stretching, O-H bending, and C-O stretching.

The manuscript presents the review of the impact of dormancy, seed storage, and pathogens on seed quality of perennial grasses and forage legumes. The outcomes of earlier studies to enhance the germination of seeds from these species are listed. Numerous studies around the world show that seed dormancy, environmental conditions, storage time after seed harvest, and the presence of pathogens on seeds, affecting the reduction of seed quality of these two groups of plants. This article discusses the possibility to partially or fully controlling impact of different factors on seed quality. Tests and experience of the presence of pathogens (especially Fusarium spp.) indicates a small percentage of infected seed of perennial grasses and legumes, which would not justify the cost of fungicides during seed processing. By applying the optimal concentration of acid in the seed, in combination with the time of exposure, it is possible to improve seed germination for more than 25% in forage grasses and legumes. Similar effects on the increase seed germination of both groups of plants can be achieving by optimal temperature treatments. Mechanical damage to the seed coat on the seeds of these crops can potentially increase germination, but new approaches are also being investigated.

Primary materials supply is the heart for engineering and sciences; depletion of natural resources and an increase in the human population by a billion in 13 to 15 years pose a critical concern on the sustainability of the materials. Therefore, functionalizing renewable materials, such as nanocellulose, possibly exploiting its properties for various practical applications, has been undertaken worldwide. Nanocellulose has emerged as a dominant green natural material with attractive and tailorable physicochemical properties, renewable, sustainable, biocompatibility, and tunable surface properties. Nanocellulose is derived from cellulose, the most abundant polymer in nature with remarkable properties of nanomaterials. This article provides a comprehensive overview of the methods used for nanocellulose preparation, structure-property and processing-property correlations, and the application of nanocellulose and its nanocomposite materials. This article differentiates the classification of nanocellulose, provides a brief account of the production methods that have been developed for isolating nanocellulose, highlights a range of unique properties of nanocellulose that have been extracted from different kinds of experiments and studies; and elaborates on nanocellulose potential applications in various areas. The present review is anticipated to provide the readers regarding the progress and knowledge related to nanocellulose. Pushing the boundaries of nanocellulose further into cutting edge applications will be of particular interest for the future, especially as cost-effective commercial sources of nanocellulose continue to emerge.

Recently, resistive random access memory (RRAM) has been an outstanding candidate among various emerging nonvolatile memories for high density storage and in-memory computing applications. However, the traditional RRAM, which accommodates two states depending on applied voltage, cannot meet the high density requirement in the era of big data. Many research groups have demonstrated that RRAM possesses the possibility of multi-level cell to overcome the demand of mass storage. Among numerous semiconductor materials, gallium oxide, as the fourth-generation semiconductor material, is highly-profile due to its excellent material proper-ties, and already be widely used in optoelectronics, high-power, resistive switching device and so on, due to its wide bandgap and transparent properties. In this study, we have successfully demonstrated the Al/GO/Ga2O3/ITO RRAM to achieve the possibility of two-bit storage. Compared to the single-layer counterpart, the bilayer structure has excellent electrical properties and stable reliability. The endurance characteristics could be enhanced above 100 switching cycles with an ON/OFF ratio of over 103. Moreover, the filament models are also described in this thesis to clarify the transport mechanisms.

The objective of this study was to compare the effect of different botanical powders and synthetic chemical in controlling Sitophilus zeamais in stored maize. A laboratory experiment was done to assess three botanicals, Zingiber officinale, Moringa oleifera, Xylopia aethiopica, in controlling the S. zeamais. The results of this study demonstrated the active potentials of these plant products as plant-derived insecticides against maize weevil. The synthetic chemical used showed both higher weevil mortality and higher grain loss than the botanicals (P< 0.05). The Botanicals also showed significance difference in the mortality rate (P < 0.05) as Z. officinale recorded the highest mortality rate (5.66%) while X. aethiopica recorded the lowest mortality rate (3.66%). The control attained the highest grain damage (7.33%) while amongst the botanicals, the highest was found in Z. officinale (7.33%) and lowest was on M. oliefera (5.33%). The exit holes made by the weevils at the end of the experiment were highest (2.66) in M. oliefera whereas lowest was recorded on X. aethiopica (1.00). Z. officinale, X. aethiopica and M. oleifera were efficacious against S. zeamais instead of synthetic chemical insecticides that have environmental health hazards and they can be used in integrated pest management by farmers and foods merchants. Therefore, since these botanicals have no any adverse effects on the seeds and safe to the environment, they are recommended for future usage in storage grains to control of S. zeamais.

By enhancing the bitumen properties with the additives produced from wastes not only can be improved the performance of flexible pavements but also can be contributed to the environment. This research aims to produce a novel pyrolytic char from different wastes and to investigate the usability of this char as an additive in bitumen. In this study, firstly, the pyrolytic char was produced from co-pyrolysis of three different wastes including waste paper cups, polypropylene (PP) and polyethylene terephthalate (PET) wastes. Properties of the char were determined by using CHN (carbon, hydrogen, nitrogen) and Fourier transform infrared spectroscopy (FTIR) analyses. The high temperature rheological properties of binders were evaluated by using DSR (dynamic shear rheometer), RV (rotational viscometer), softening point and penetration tests. Additionally, specific gravity, storage stability, high temperature performance grades (PG) and temperature susceptibilities of binders were determined. Test results showed that this pyrolytic char enhanced the high temperature properties of neat bitumen by increasing softening point, viscosity, rutting resistance and high temperature PG. And, it can be said that the bituminous binder modified with this pyrolytic char had a good storage stability when it was used at 8% ratio in neat bitumen.

The popularity of cloud computing is growing owing to its large data storage capacity and high computation power. It provides online, on-demand, scalable application solution, removes hardware and software barriers for non-specialist, rapidly integrates and deploys desired and necessary facilities, supports quick upgrading and addition of features. Users get benefitted with the selection of the appropriate cloud computing platform for their projects. Here, our paper provides a comprehensive overview of the services provided to the users by the most common cloud computing service providers. This paper could be used as a reference while selecting the best service provider based on the requirements of the projects.

The effect of capitalization premium in forest estate markets on forest management and climate change mitigation economics is investigated. It is shown that proportional goodwill in capitalization induces linear scaling of the financial return, without any contribution to sound management practices. However, there is a financial discontinuity as harvesting deteriorates goodwill. On the contrary, capitalization premium set on bare land as a tangible asset would increase timber storage and carbon sequestration. Observations indicate that the proportional goodwill is closer to reality within the Nordic Region, resulting in continuity problems but a reduced capital expense for carbon storage.

Seed viability is routinely measured on seeds that fail to germinate at the end of an experiment. Together with the number of germinants, this is used to estimate viability of the seeds at start of the experiment (i.e., initial viability) and provides the comparative basis on which germination success is determined. Perusal of the literature shows that sometimes (perhaps often, as the problem has yet to be recognized or reported) prolonged duration in the treatment, especially the control where little germination occurs, can lead to loss of viability. This results in underestimation of initial viability if that treatment is used. I caution against the routine use of end-of-trial germination and viability of ungerminated seeds as an estimate of initial viability in determining germination success of various treatments. I explore ways to deal with the problem but the preference is for estimates of initial viability to be undertaken on a separate sample of seeds concurrently with the experiment as this avoids the risk of seed death during the trial.

The structural, elastic, anisotropic elastic, electronic, vibrational and properties of the Perovskite type Hydrides RbXH3 (X = Be, Ca, Mg) were performed via Vienna Ab – initio Simulation Pac-kage (VASP) based on Density Functional Theory (DFT). Our results have exhibited a well-agreement with previous calculations and experiments for each compound. In order to de-termine physical properties of RbXH3 has been used the Generalized Gradient Approximation (GGA) with Perdew-Burke-Ernzerhof (PBE) functional at this study. Present compounds were found to be mechanically stable as well as their gravimetric hydrogen storage capacities has been investigated. The Perovskite type Hydrides RbBeH3 and RbMgH3 has an indirect bandgap of 0.274 eV and 2.209 eV while RbCaH3 has a direct bandgap of 3.274 eV respectively and therefo-re these compounds has shown a semiconductor behaviour at equilibrium. Besides directional dependence of anisotropic properties was visualized by representing them with maximum - mi-nimum points..

This review reports the available technologies for the flexible utilization of biomass towards negative CO₂ emissions and addresses the possibility to couple biogas production plants with the electrical grid converting excess electrical energy into storable chemical molecules. This changed mind-set towards biomass utilization can lead readily to the implementation of negative CO₂ emission along the entire bioenergy supply chain without limiting the potential for Power-to-X applications. First, the technologies for direct conversion of waste and wood into gaseous energy carriers are screened, to highlight the potential for the production of renewable fuels. Second, the processes for the removal of CO₂ from biogenic gas streams are analysed in terms of technological performance, cost and further potential for the CO₂ recovered. These technologies are the key to pre-combustion CO₂ capture and negative emissions. Third, the possibility of coupling biomass conversion and synthetic fuels production is explored, providing an overview on the technical maturity of the various energy storage processes. The flexible use of biomass can be an essential part of the future CO₂-free energy systems, as it can directly provide energy carriers all around the year and also large quantities of climate-neutral carbon for the production of synthetic fuels with renewable energy. In turn, when no additional renewable electricity is available, the CO₂ by-product from biofuel synthesis can be used for the negative emissions. This opens the way to an efficient strategy for the seasonal storage of electrical energy, realizing a carbon-neutral energy system coupled with the development of carbon-negative energy strategy.

This research project focuses on the optimization of the hybrid energy system together with the assistance of thin-film coatings aiming to achieve self-sustainable food and crop storage facilities which will run effectively with its own generated energy. An infrastructure will be designed and constructed that will comprise a hybrid power generation system accompanied by thin-film coated semitransparent and non-transparent construction materials for energy saving. Thin-film low emissivity (Low-E) type coatings will assist the transparent or semitransparent construction materials to reflect most of the infrared (IR-mostly heat) and UV spectra of sunlight without interrupting the visible spectrum and will lead to saving energy consumption by reducing the heat and lighting during day time

The Residential and Industrial zones as is, rely heavily, if not exclusively, on Hydrocarbons. Hydrocarbon thermal machinery such as Spark Ignition-Compression Ignition engines, Gasoline-Diesel generators, Coal-Lignite gasifiers, residential diesel-powered heating systems, Pyrolysis units and so on, are commonly met all around the planet. Such technology practically oxidizes Hydrocarbons to produce either heat, steam or useful mechanical work depending on the application, though energy losses are not, by any means, insignificant. Advanced material processing is an industrial sector who’s energy demand is significant and it is important for the general public to come to terms with the fact that by implementing Hydrogen technology to power such plant while at the same time improving the energy equilibrium of houses(advanced materials), communities would be taking major steps towards Climate Change effects debilitation. The downside of Hydrocarbon thermochemical exploitation can be described by the limited resources-reserves and the gaseous pollutant emissions (CO2, CO, NOx, SOx). In recent years, the Industrial zone as a whole has began taking a turn towards Electrification without having established the necessary infrastructure to support such a transition. Indicatively, at current rate of production, dead Lithium-Ion batteries are projected to reach as high as 11,000 metric tons by 2030, yet there is no recycling scheme in place, not to mention the prospect of that number rising even more, given the recent e-mobility trend. As it pertains to Electrification, such powertrains-machinery require electricity and a battery. Electricity production is mainly achieved through Coal-Lignite gasification, Batteries require metals, among others, for manufacturing, meaning that up-on mining, local water resources are contaminated, another very important ‘aspect’ of Lithium(per say) mining is that child labor is often associated with such processes, a truly despicable act. All of the above paint a crystal-clear picture as to how ‘environmentally friendly’ reckless-rushed Electrification really is. Climate Change is up-on us and it’s effects on the planet are obvious, the most important of which is glacier melting due to rising of the global Temperature. The COVID-19 crisis is a sign of what could come from glacier melting could as ice contains potentially harmful-toxic to humans, biological entities that are sure to be introduced to the general public if we were to continue exploiting mineral resources. Purpose of this paper is to provide a general overview of the technology around Hydrogen.

Smartphone has become one of the most revolutionary devices in the history of computing. With various kinds of applications, the scope of smartphone has been significantly broadened in the past few years including almost every aspect in our daily life. However, due to the limited on-board resources such as CPU, storage, network bandwidth and battery power, smartphones and the mobile network serving them bring new challenges that have not been encountered in the traditional computing and networking environments. This dissertation focuses on the research areas of improving the network architecture and enhancing the current applications on smartphones. It mainly investigates the areas in the following two directions for three representative categories of mobile services. - In the first direction, the dissertation aims to develop new communication models for smartphone Ad-Hoc networks to achieve efficient communication in the proximity. It is motivated by the fact that smartphone Ad-Hoc networks can help improve the current location-based services and propel new applications. Moreover, the new communication models provide complementary alternatives to the traditional infrastructure-based wireless networks. - In the second direction, the dissertation focuses on improving the other two categories of services, cloud storage services and real-time video streaming services for mobile devices. In the field of cloud storage, we introduce a cloud-assisted approach to provide a set of advanced file operations, such as encryption, decryption and compression, on smartphones. Furthermore, by utilizing the on-board Near Field Communication(NFC) module, we develop an algorithm to securely share the files between mobile devices. For the services of real-time video streaming, we propose approaches that identify a user’s status by analyzing the accelerometer data and then, dynamically adjust the buffer mechanism to save network bandwidth on smartphones.

Environmental and economic needs drive the increased penetration of intermittent renewable energy in electricity grids, enhancing uncertainty in market conditions prediction and network constraints. Thereafter, the importance of energy systems with flexible dispatch is reinforced, ensuring energy storage as an essential asset for these systems to be able to balance production and demand. In order to do so, such systems should participate in whole-sale energy markets, enabling competition among all players, including conventional power plants. Consequently, an effective dispatch schedule considering market and resource uncertainties is crucial. In this context, an innovative dispatch optimization strategy for schedule planning of renewable systems with storage is presented. Based on an optimization algorithm combined with a machine learning approach, the proposed method develops a financial optimum schedule with the incorporation of uncertainty information. Simulations performed with a concentrated solar power plant model following the proposed optimization strategy demonstrate promising financial improvement with a dynamic and intuitive dispatch planning method, emphasizing the importance of uncertainty treatment on the enhanced quality of renewable systems scheduling.

Mobile Cloud Computing(MCC) is a recent technology used by various users worldwide. In 2015, more than 240 million users used mobile cloud computing which gives a profit of $5.2 billion to service providers. MCC is a combination of Mobile computing and cloud computing. By the combination of these two, it gives various challenges like network access, elasticity, management, availability, security, privacy, etc. Here security issues are considered because both the security issues of mobile computing and cloud computing are considered as important like data security, virtualization security, partitioning security, Mobile cloud application security, Mobile device security. This paper gives a detailed study of security issues in mobile cloud computing and its prevention measures.

Thermophysical characterization of three paraffin waxes (RT27, RT21 and RT35HC) is carried out in this study using DSC, TGA and transient plane source technics. Then, a numerical study of their melting in a rectangular enclosure is examined. The enthalpy-porosity approach is used to formulate this problem in order to understand the heat transfer mechanism during the melting process. The analysis of the solid-liquid interface shape, the temperature field shows that the conduction is the dominant heat transfer mode in the beginning of the melting process. It is followed by a transition regime and the natural convection becomes the dominant heat transfer mode. The effects of the Rayleigh number and the aspect ratio of the enclosure on the melting phenomenon are studied and it is found that the intensity of the natural convection increases as the Rayleigh number is higher and the aspect ratio is smaller. In the second part of the numerical study, a comparison of the performance of paraffins waxes during the melting process is conducted. Results reveals that from a kinetically RT21 is the most performant but in term of heat storage capacity, it was inferred that RT35HC is the most efficient PCM.

Shale gas production is associated with significant usage of fresh water and discharge of wastewater. Consequently, there is a necessity to create the proper management strategies for water resources in shale gas production and to integrate conventional energy sources (e.g., shale gas) with renewables (e.g., solar energy). The objective of this study is to develop a design framework for integrating water and energy systems including multiple energy sources, cogeneration process, and desalination technologies in treating wastewater and providing fresh water for shale gas production. Solar energy is included to provide thermal power directly to a multi-effect distillation plant (MED) exclusively (to be more feasible economically) or indirect supply through a thermal energy storage system. Thus, MED is driven by direct or indirect solar energy, and excess or direct cogeneration process heat. The proposed thermal energy storage along with the fossil fuel boiler will allow for the dual-purpose system to operate at steady-state by managing the dynamic variability of solar energy. Additionally, electric production is considered to supply a reverse osmosis plant (RO) without connecting to the local electric grid. A multi-period mixed integer nonlinear program (MINLP) is developed and applied to discretize operation period to track the diurnal fluctuations of solar energy. The solution of the optimization program determines the optimal mix of solar energy, thermal storage, and fossil fuel to attain the maximum annual profit of the entire system. A case study is solved for water treatment and energy management for Eagle Ford Basin in Texas.

Energy storage has become a fundamental component in renewable energy systems, especially those including batteries. However, during the charging and the discharging process, there are some parameters that are not controlled by the user. That uncontrolled working leads to aging of the batteries and a reduction of their life cycle. Therefore, it causes an early replacement. Different control methods have been developed with the goal of protecting the battery and extending its life expectancy, being the most used the constant current-constant voltage. However, several studies show that charging time can be reduced by using Fuzzy Logic Control or Model Predictive Control. Other benefits are; temperature control and an extension of life expectancy. For all these reasons, FLC and MPC have proven to be more efficient than traditional charge control methods.

Yellow nanorod Mg-MOF-74 was obtained by solvothermal synthesis method. XRD、N2 adsorption-desorption isotherms、SEM and TGA results suggest that the particle size of Mg-MOF-74 reaches 400 nm after the introduction of sodium acetate in the precursor of Mg-MOF-74. Besides, the morphology of Mg-MOF-74 was changed from cauliflower to rod particles. At the same time, the BET specific surface area and pore volume of Mg-MOF-74 were also increased a lot. Then the CO2 dynamic adsorption capacity of Mg-MOF-74 was measured by self-made fix bed under 30 ℃、0.1 bar CO2 partial pressure. The results show that the CO2 adsorption capacity of Mg-MOF-74-N2 reaches 3.67 mmol/g and its CO2 adsorption capacity remains unchanged after 10 times CO2 adsorption-desorption cycles.

Towards better understanding of factors controlling carbon (C) exchange between inland waters and atmosphere, we addressed inorganic carbon cycle in semi-arid lakes of Central Eurasia, subjected to strong impact of on-going climate change. For this, we assessed the hydrochemical vari-ability and quantified its control on formation of authigenic carbonate minerals, occurring within the upper layer of sediments in 43 semiarid lakes located in the southwest of Western Siberia (Central Eurasia). Based on measurements of pH, total dissolved solids (TDS), cationic and anionic composition, dissolved organic and inorganic C, as well as textural and mineralogical characterization of bottom sediments using X-ray diffraction and scanning electron microscopy, we demonstrate that lake water pH and TDS are primarily controlled by both lithological and climatic context of the lake watershed. We have not revealed any direct relationships between lake morphology and water chemistry. The most common authigenic carbonates scavenging atmospheric CO2 in the form of insoluble minerals in lake sediments were calcite, aragonite, Mg-calcite, dolomite and hydro-magnesite. The calcite was the most common component, aragonite mainly appears in lakes with sediments enriched in gastropod shells or artemia cysts, while hydromagnesite was most common in lakes with high Mg/Ca molar ratios, as well at high DIC concentrations. The relationships between mineral formation and water chemistry established in this study can be generalized to a wide suite of arid and semi-arid lakes in order to characterize current status of inorganic C cycle and predict its possible modification under on-going climate warming such as water temperature rise and change of hydrological connectivity, primary productivity and nutrient regime.

Due to increasing concerns about global warming and energy crisis, intensive efforts have been made to explore renewable and clean energy sources. Single-atom metals and two-dimensional (2D) nanomaterials have attracted extensive attention in the fields of energy and environment because of their unique electronic structures and excellent properties. In this review, we sum-marize the state-of-art progress on the single-atom metal supported at 2D MoS2 (single-atom metal/2D MoS2) for electrochemical CO2 reduction and water splitting. First, we introduce the advantages of single-atom metal/2D MoS2 catalysts in the fields of electrocatalytic CO2 reduction and water splitting, followed by the strategies for improving electrocatalytic performances of single-atom metal/2D MoS2 hybrid nanomaterials and the typical preparation methods. Further, we discuss the important applications of the nanocomposites in electrocatalytic CO2 reduction and water splitting via some typical examples, particularly focusing on their synthesis routes, modification approaches, and physiochemical mechanisms for improving their electrocatalytic performances. Finally, our perspectives on the key challenges and future directions of exploring high-performance metal single-atom catalysts are presented based on recent achievements in the development of single-atom metal/2D MoS2 hybrid nanomaterials.

In hydraulic systems, energy dissipation can be significant. The pressure drops that can occur in the hydraulic circuit, influenced by the adopted drive architecture, result in an absorbed power often significantly greater than that required by the mechanical system. In this paper, a comparative study of energy efficiency among five drive common architectures in industrial hydraulic axes is carried out. The analysis is applied to a hydraulic blanking press with variable speed and force, a fairly frequent industrial system, e.g. in the production of semi-finished brass products. Standard, regenerative, high-low, variable displacement pump and variable speed drive for a fixed displacement pump configurations have been analysed and compared. An adequate and optimized sizing of the various components of the system has been carried out in each case and subsequently the energy consumption has been estimated for a load cycle common to all the considered cases. The results show that the choice of power generation architecture of the hydraulic system has a very significant impact on energy efficiency and consequently operating costs and carbon footprint. The performed quantification of the potential energy efficiency of the considered drive architectures can be very useful in guiding energy-conscious choices.

As urban populations and transport demand expand, Pakistani metropolitan centers face traffic congestion and environmental challenges. This research aims to assess carpooling (CP) to alleviate traffic congestion, fuel demand, and pollution. This study was conducted in Islamabad, a fast-growing city with a high percentage of personal cars in Pakistan, to assess the travelers’ perceptions, and public acceptance of CP and determine the effects on traffic congestion, fuel consumption, and CO2 emissions. The investigation of travelers' perceptions towards CP was conducted through a stated preference questionnaire survey. A total of 700 responses from one million population of Islamabad were collected as per Sloven's Formula. SPSS and Smart PLS software were used for data analysis. Various factors influencing peoples’ travel perceptions, mode choice, and tendency to carpool, were categorized to evaluate the relationship between travelers’ perception and the tendency to carpool in the presence of mode choice as a mediating variable. Confirmatory factor analysis was conducted in SMART PLS to refine the number of scale items for each variable. One-way ANOVA, step-wise and mediated multiple regression analysis was conducted in SPSS to check the direct and mediating relationship between different variables. Moreover, the probability of reducing traffic congestion and assessing fuel reduction resulting from CP was also analyzed. The findings imply that travelers’ mode choice acts as a mediator between the relationship between travelers’ perception and tendency to carpool. Furthermore, results predicted that CP might reduce 0.25 million cars on the road, about 33.6% of the total private vehicles. Thereby, saving up to 546,810 barrels per year, about 3.42% of Pakistan's total petrol consumption. The findings of this study could be helpful for transport planners, environmentalists, and policymakers to implement carpool systems. Thus, reducing traffic congestion and harmful CO2 emissions and maintaining a sustainable environment.

Elevated indoor CO2 levels might have adverse effects on human health. However, the introduction of outdoor air to lower indoor CO2 concentrations results in significant HVAC energy consumption. Aligning with office hours and the natural light cycle, the utilization of photosynthesis in living walls offers an energy-efficient and sustainable solution for the mitigation of high CO2 levels in office spaces. This study experimentally investigates the impacts of the carbon fixation pathways, light intensity, and substrate moisture content on the CO2 removal rate of living walls at the room scale. Furthermore, the fresh air energy-saving effects of living walls under different scenarios are accurately simulated in EnergyPlus. The results demonstrate that choosing C3 plants over CAM plants in living walls yields higher CO2 removal efficiency. In a 30-m2 office room accommodating 2-3 occupants, living walls can reduce the demand for fresh air by 12.3%-27.8% and decrease fresh air energy consumption by 11.2%-28.2%. The city with the highest energy savings has energy savings that are 4.5 times greater than those of the city with the lowest energy savings. The findings of this research promote the application and development of living walls, thus providing a viable solution for improving indoor air quality.

Ce-promoted NiMgAl mixed-oxide (NiCex-C, x = 0, 1,5,10) catalysts were prepared from the quaternary hydrotalcite precursors for CO2 hydrogenation to methane. By engineering the Ce contents, NiCe5-C showed its prior catalytic performance in low-temperature CO2 hydrogenation, being about 3 times higher than that of Ce-free NiCe0-C catalyst (TOF of NiCe5-C and NiCe0-C: 1.19 h-1 vs 0.39 h-1 @ 250 oC). With extensive characterization, it was found that Ce dopants promoted the reduction of NiO by adjusting the interaction between Ni and Mg(Ce)AlOx support. The higest ratio of surface Ni0/(Ni2+Ni0) was obtained over NiCe5-C. Meanwhile, the surface basicity was tailored with Ce dopants. The strongest medium-strength basicity and highest capacity of CO2 adsorption was achieved on NiCe5-C with 5wt% Ce content. The TOF tests indicated a good correlation with medium-strength basicity over the NiCex-C samples. The results showed that the high medium-strength and Ce-promoted surface Ni0 species endows the enhanced low-temperature catalytic performance in CO2 hydrogenation to methane.

The reckless use of non-replenishable fuels by the growing population for energy and the resultant incessant emission of hazardous gases and waste products into the atmosphere insisted scientists to fabricate materials capable of managing these global threats at once. In recent studies, photo-catalysis employed focus on utilizing renewable solar energy to initiate chemical processes with the aid of semiconductors and highly selective catalysts. A wide range of nanoparticles have showcased promising photocatalytic properties. Ultrasmall metal nanoclusters (MNCs) with sizes below 2 nm, stabilized by ligands shows discrete energy levels, exhibits unique optoelectronic properties which are vital to photocatalysis. In this review, we intend to compile information on varying photocatalytic efficiency of metal NCs with respect to changes in their properties. Review discusses about the photocatalytic activity of atomically precise ligand-protected MNCs and its hybrids in the domain of in energy conversion processes like photodegradation of dyes, Oxygen Evolution Reaction (ORR), Hydrogen Evolution Reaction (HER) and CO2 Reduction Reaction (CO2RR), and photosensitizer in solar cell.

Natural ventilation in a building is an effective way to achieve acceptable indoor air quality. Ventilation dilutes contaminants such as bio-effluents generated by occupants, substances emitted from building materials, and water vapor generated by occupants' activities. In a building that requires heating and cooling, adequate ventilation is crucial to minimize energy consumption while maintaining healthy indoor air quality. However, measuring the actual magnitude of the ventilation rate, including infiltration through the building envelope and airflow through building openings, is not always feasible. In this study, the occupant-generated carbon dioxide (CO2) tracer gas decay method was applied to estimate the ventilation rates in an office room in Seoul, South Korea, from summer to winter. Using the method, real-time ventilation rates can be calculated by monitoring indoor and outdoor CO2 concentrations without injecting a tracer gas. 145mm-diameter circular openings on the fixed glass were used for natural ventilation in the test room. As a result, firstly, the indoor CO2 concentrations were used as an indicator to evaluate how much the indoor air quality deteriorated when all the windows were closed in an occupied office room compared to international standards for indoor air quality. Moreover, we found out the estimated ventilation rates varied depending on various environmental conditions, even with the same openings for natural ventilation. Considering the indoor and outdoor temperature differences and outdoor wind speeds as the main factors influencing the ventilation rates, we analyzed how they affected the ventilation rates in different seasons of South Korea. When the wind speeds were calm, the temperature difference played as a factor that influences the estimated ventilation rates. On the other hands, when the temperature differences were low, the wind speed was the primary factor. This study raises awareness about the risk of poor indoor air quality in office rooms that could lead to health problems or unpleasant working environments. This study presents an example of estimating the ventilation rates in an existing building. In the same way, the ventilation rate in an existing building can be simply estimated while using the building as usual, and appropriate ventilation strategies for the building can be determined to maintain desired indoor air quality.

Land’s basic metric is soil organic carbon (SOC) yet global estimates range 1,417–15,000 Gt C. Erosion of ancient topsoil and loss of soil taxa are most urgent of all context-triage concerns, and most ignored. Re-evaluation of topographical terrain on a non-flat Earth increases most soil dynamic inventories. Carbon credits of our neglected and disappearing SOC stocks are enumerated for mineral soils (~4,100 Gt C plus ca. 20–30% glomalin), Permafrost (>4,200 Gt C), peat (1,123 Gt C), plant roots (916 Gt C), litter (600 Gt C), microbes (200 Gt C), fungi (30 Gt C), biocrust (10–20 Gt C), earthworms (2.3–3.6 Gt C), termites (0.15 Gt C), nematodes (0.06 Gt C), ants (0.024 Gt C), and soil viruses (0.02–4.0 Gt C). Net contribution to atmospheric CO₂ is more from biotic topsoil loss (>10 Gt C/yr) than fossil fuels (<10 Gt C/yr). Although higher CO₂ results in a terrestrial greening effect with Net Primary Productivity (NPP) now ~220 Gt C/yr (cf. ~20 Gt C/yr Ocean NPP), this is arguably offset by topsoil erosion, desert expansion, plus fire at net ~16–20 Gt C/yr lost due, in part, to extravagant meat-eating with unsupportable, humus-depleting farm management. In particular, excess synthetic Nitrogen acidifies topsoil and destroys the natural SOC biota. Review shows critical topsoil loss up to 20,000 tonnes per second and, when soil microbes/invertebrates are properly considered, extinctions as high as 23 taxa per second. Sustainable Development Goals (SDGs) fail without solid soil foundation. Rather, heritage farm-data points to resolution in organic husbandry. Remedy via natural vermi-compost, 100% organic farming and practical Permaculture is under a simple premise that the Problem (i.e., SOC loss) is the Solution (viz., SOC restoration).

Seasonal oscillations in the partial pressure of carbon dioxide (pCO2) in the Earth’s atmosphere stronger in northern latitudes are assumed to show that terrestrial photosynthesis exceeds respiration in summer reducing the pCO2, but increasing in winter when respiration exceeds photosynthesis. We disagree, proposing that variations in the temperature of the surface mixing zone of seawater also regulate the atmospheric pCO2, thermodynamically. We show that carbonate (CO32-) concentrations will therefore increase in summer with CaCO3 (calcite or aragonite) becoming less soluble, so calcium and carbonate ions are predicted to aggregate more while CO2 concentration falls in warmer seawater, thermodynamically favoring lower atmospheric pCO2. In winter, these physical processes are reversed, redissolving suspended calcite thus increasing carbonate alkalinity; carbonate concentration lessens as bicarbonate and soluble CO2 increase, raising the pCO2 in air. Our numerical computation shows that thermal fluctuations in equilibria favor absorption from air of more than one mole of CO2 per square meter in summer, coinciding with calcite formation maximizing in warmer water, potentially augmenting limestone reefs if there is a trend for increasing temperature . Another assumption we challenge is that upwelling from deeper water is the sole cause of increases in dissolved inorganic carbon (DIC) and alkalinity in surface waters, particularly in the southern hemisphere. Instead, calcite dissolution is favored as water temperature falls near the surface. It is well established that the seasonal summer decline in atmospheric CO2 coincides in fertile seawater with higher rates of biotic calcification and acidity, allowing increased CO2 capture by photosynthesis. However, its reversal in winter is proposed to be also a result of the cyclic dissolution of calcite as temperature falls, facilitated by biogenic respiration now exceeding photosynthesis; this can mutually provide the CO2 needed to convert carbonate ion alkalinity from calcite dissolution with bicarbonate increasing. Physical reasons why this oscillation is more obvious in the northern hemisphere include greater seasonal variations in water temperature (ca. 7.1 oC) being almost twice that in the cooler southern hemisphere (ca. 4.7 oC) and the greater depth of the surface mixing zone of seawater in the southern oceans. Evidence from 13CO2 fluxes between surface seawater and air is also assessed to test this hypothesis but questions remain regarding the regional rates of inorganic precipitation and dissolution of CaCO3 in the mixing zone. In summary, rapid biogenic calcification is favored by summer photosynthesis, but slower abiogenic calcification is more likely in warmer water.

In this study, we analyzed the feasibility of various carbon neutrality methods based on the first principles of carbon sequestration, namely energy use efficiency and elemental stoichiometry. We believe that wood burial is the only currently feasible carbon neutrality method because this method has no theoretical uncertainties, can be implemented immediately on a large scale, has a long sequestration time, low cost, low technical requirements, and relatively little impact on agriculture.

Since people spend most of their time in indoor environments, the objective of this work was to study indoor air quality perception and its effects on users’ thermal comfort. Based on previous data from a building with a central air-conditioning system and two mixed-mode buildings located in the humid subtropical climate of Florianópolis, southern Brazil, statistical analyses were performed. Each user subjective answer obtained through a questionnaire was combined with the corresponding environmental conditions – measured using microclimate stations, a portable thermo-anemometer and a CO2 analyser. Results showed that improvement in air quality was associated with the reduction of air temperature and humidity ratio. Also, there was a significant influence of thermal, air movement and humidity sensation and acceptability of air quality perception. Users felt more satisfied or neutral with air quality for being in thermal comfort, and not because of the CO2 level – which means that air quality perception is influenced by factors other than CO2. This study recommends the implementation of an air exchange device in split air-conditioners with air recirculation used in mixed-mode buildings in Brazil. It is important to provide suitable indoor ventilation to reduce pollutants concentration, ensure good air quality and prevent respiratory diseases.

Many corporations aspire to become Net Zero Carbon Dioxide by 2030-2050. This paper examines what it will take. It requires understanding where energy is produced and consumed, the magnitude of CO2 generation, and the Carbon Cycle. Reviews are provided for prior technologies for reducing CO2 emissions from fossil to focus on their limitations and to show that none offer a complete solution. Both biofuels and CO2 sequestration reduce future CO2 emissions from fossil fuels. They will not remove CO2 already in the atmosphere. Planting trees has been proposed as one solution. Trees are a temporary solution. When they die, they decompose and release their carbon as CO2 to the atmosphere. The only way to permanently remove CO2 already in the atmosphere is to break the Carbon Cycle by growing biomass from atmospheric CO2 and sequestering biomass carbon. Permanent sequestration of leaves is proposed as a solution. Leaves have a short Carbon Cycle time constant. They renew and decompose every year. Theoretically, sequestrating a fraction of the world’s tree leaves can get the world to Net Zero without disturbing the underlying forests. This would be CO2 capture in its simplest and most natural form. Permanent sequestration may be achieved by redesigning landfills to discourage decomposition. In traditional landfills, waste undergoes several stages of decomposition, including rapid initial aerobic decomposition to CO2, followed by slow anaerobic decomposition to methane and CO2. The latter can take hundreds to thousands of years. Understanding landfill chemistry provides clues to disrupting decomposition at each phase.

It is important to distinguish between natural earthquakes and those induced by CO2 injection at carbon capture and storage sites. For example, the 2004 Mw 6.8 Chuetsu earthquake occurred close to the Nagaoka CO2 storage site during gas injection, but we could not quantify whether the earthquake was due to CO2 injection or not. Here we simulated changes of pore pressure during CO2 injection at the Nagaoka site and compared them with estimated natural seasonal fluctuations of pore pressure due to rainfall and snowmelt as well as estimated pore pressure increases related to remote earthquakes. We clearly distinguished changes of pore pressure due to CO2 injection from those due to rainfall and snowmelt. The simulated local increase in pore pressure at seismogenic fault area was much less than the seasonal fluctuations related to precipitation and increases caused by remote earthquakes, and the lateral extent of pore pressure increase was insufficient to influence seismogenic faults. We also demonstrated that pore pressure changes due to distant earthquakes are capable of triggering slip on seismogenic faults. The approach we developed could be used to distinguish natural from injection-induced earthquakes and will be useful for that purpose at other CO2 sequestration sites.

We used population reconstruction techniques to assess for the first time the population dynamics of a seagrass, Cymodocea nodosa, exposed to long-term elevated CO₂ near three volcanic seeps and compare them with reference sites away from the seeps. Under high CO₂, the density of shoots and of individuals (apical shoots), and the vertical and horizontal elongation and production rates, were higher. Nitrogen effects on rhizome elongation and production rates and on biomass, were stronger than CO₂ as these were highest at the location where the availability of nitrogen was highest. At the seep where the availability of CO₂ was highest and nitrogen lowest, density of shoots and individuals were highest, probably due to CO₂ effects on shoot differentiation and induced reproductive output, respectively. In all three seeps there was higher short- and long-term recruitment and growth rates around zero, indicating that elevated CO₂ increases the turnover of C. nodosa shoots.

Over the last 20 years, there has been a significant increase in the number of unexplained physiological events (UPEs) reported by pilots of fighter jets across different fleets. The UPEs have resulted in grounding some types of aircraft, loss of airplanes, and even loss of life. Despite considerable research, no single agreed-upon root cause has been found that explains UPEs, and therefore no reliable corrective actions exist. The purpose of this review was to analyze the literature related to other industries in which artificial hyperoxic gas mixes are employed and similar adverse reports have been reported. Based on analysis of the literature, it is hypothesized that UPEs are caused by unlimited delivery of high-dose oxygen in excess of officially approved oxygen schedules in the presence of inadequate airflow rates, at a time when the positive pressure breathing feature of their oxygen regulator system is not used. During flight maneuvers such as climbs, turns, and descents, pulmonary vital capacity is impaired by G-maneuvers and oxygen- and G-induced atelectasis. At the same time, tidal volume is reduced by flight gear, and effective gas exchange is not supported by adequate ventilation. These factors combine to produce hypercarbia, respiratory acidosis, acute respiratory distress syndrome, CO₂ narcosis, and coma. In fact, reports from field data related to incidents in F-18S/H, showing that emergency oxygen did not correct the hypoxia-like symptoms including long-lasting periods of incapacitation and prolonged headaches, lend support to this hypothesis.

It is widely discussed that growth of GDP has a vague impact on environmental pollution due to the emissions of carbon dioxide from consumed fossil fuels in production, transportation and power generation, and creation of required instruments to control environmental pollution as well. Due to the fact that environmental pollution can be a reason of mortality increase in a society, the main purpose of this study is to investigate the relationship between economic growth, fossil fuel consumption, mortality (from cardiovascular disease, cancer, diabetes and chronic respiratory disease) and environmental pollution using Generalized Method of Moments (GMM) estimation technique in the case of CIS member states over the period of 1993-2018. The major results revealed CO2 emissions in in the region of CIS have a positive effect on increase of mortality from cardiovascular disease, cancer, diabetes and chronic respiratory disease. In regards to fossil fuel consumption, the estimation proved that this variable affects mortality from cardiovascular disease, cancer, diabetes and chronic respiratory disease positively. In addition, we found effect of economic growth, population growth and inflation rate positively, while any improvement in human development index (HDI) has a negative effect on increase of mortality from cardiovascular disease, cancer, diabetes and chronic respiratory disease in the CIS region. It is recommended that the CIS member states carry out different policies to improve energy transition indicating movement from fossil fuel energy sources to renewable ones. Moreover, we recommend the CIS member states to enhance various policies for easy access to the electricity from green sources and increase of renewable supply through improved technologies, sustainable economic growth, and increase of using green source in daily social life.

In 2016, the global environmental impact of greenhouse gas (GHG) emissions was 49.3 gigatons CO₂ equivalent. Worldwide, the transportation sector is responsible for 14% of GHG. Electric vehicles (EV) powered by less-polluting energy sources are one way to reduce the environmental impact of the transportation sector, but immediate transportation demands cannot be met by existing EV technology. Use of less polluting biofuel in place of petroleum-based gasoline or diesel fuel to power the existing transportation fleet is a widely accepted transitional solution, including in the Republic of Korea. The purpose of this research is to investigate approaches to biofuels in the US and the UK in order to evaluate Korea’s current energy policies related to use of biofuels and to make recommendations for strengthening Korea’s energy policy. This article addresses only policies for use of biodiesel rather than ethanol (widely used in the US) because ethanol is not used in Korea. This research shows that Korea calculates GHG using the principle that biofuel is carbon neutral, but energy policies in the US and the UK treat biofuel as not entirely carbon neutral. Korea should examine how to calculate GHG from biodiesel according to the standard set by the UK in order to work toward a more environmentally sustainable energy policy.

Considering the high potential of hydrogen (H₂) as a clean energy carrier, the implementation of high performance and cost-effective biohydrogen (bioH₂) purification techniques is of vital importance, particularly in fuel cell applications. In this context, membrane technology is a potentially energy-saving solution to obtain high-quality biohydrogen. The most promising poly(ionic liquid) (PIL) - ionic liquid (IL) composite membranes previously studied by our group for CO₂/N₂ separation, containing pyrrolidinium-based PILs with fluorinated or cyano-functionalized anions, were chosen as starting point to explore the potential of PIL–IL membranes for CO₂/H₂ separation. The CO₂ and H₂ permeation properties at the typical conditions of biohydrogen production (T =308 K and 100 kPa of feed pressure) were measured and discussed. PIL–IL composites prepared with [C(CN)₃]^– anion showed higher CO₂/H₂ selectivities and H₂ diffusivities compared to those containing [NTf₂]^– anion. All the membranes revealed CO₂/H₂ separation performances above the upper bound for this specific separation, highlighting the composite incorporating 60 wt% of [C₂mim][C(CN)₃] IL.

Microporous organic polymers (MOPs) are promising materials for gas sorption because of the intrinsic and permanent porosity, designable framework and low density. The introduction of nitrogen-rich building block in MOPs will greatly enhance the gas sorption capacity. Here, we report the synthesis of MOPs from the 2,4,6-tris(4-ethynylphenyl)-1,3,5-triazine unit and aromatic azides linkers via click polymerization reaction. FTIR and solid state 13C CP-MAS NMR confirm the formation of the polymers. CMOP-1 and CMOP-2 exhibit microporous networks with BET surface area of 431 and 406 m2 g-1 and narrow pore size distribution under 1.2 nm. Gas sorption isotherms including CO2 and H2 were measured. CMOP-1 stores superior CO2 level of 8.2 wt% (1.88 mmol g-1) at 273 K/1.0 bar and H2 uptake up to 0.6 wt% at 77 K/1.0 bar, while CMOP-2 with smaller surface area shows lower CO2 adsorption capacity of 7.3 wt% (1.66 mmol g-1) and H2 uptake (0.5 wt%). In addition, I2 vapor adsorption was tested at 353 K. CMOP-1 shows higher gravimetric load of 160 wt%. Despite of the moderate surface area, the CMOPs display excellent sorption ability for CO2 and I2 due to the nitrogen-rich content in the polymers.

The article delves into the crucial realm of compressing hydrogen in its gaseous state, a pivotal process for enhancing its viability in both civil and industrial sectors. The study initiates by providing a concise overview and comparison of diverse hydrogen storage methodologies, laying the groundwork with an in-depth analysis of hydrogen's thermophysical properties. It scrutinizes plausible configurations for hydrogen compression, aiming to strike a delicate balance between energy consumption, predominantly derived from the fuel itself, and the requisite number of compression stages. Notably, to render hydrogen storage competitive in terms of volume, pressures of at least 350 bar are deemed essential, albeit at an energy cost amounting to approximately 10% of the fuel's calorific value. Multi-stage compression emerges as a crucial strategy, not solely for energy efficiency, but also to curtail temperature rise, with an upper limit set at 200°C. This nuanced approach is underlined by the exploration of compression levels commonly cited in the literature, particularly 350 bar and 700 bar. Ultimately, the study advocates for a three-stage compression system as a pragmatic compromise, capable of achieving high-pressure solutions while keeping compression work below 10 MJ/kg, a threshold indicative of sustainable energy utilization.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

Nanoporous materials, such as Metal-Organic Frameworks (MOFs), are renowned for their high selectivity as gas adsorbents due to their specific surface area, nanoporosity, and active surface chemistry. A significant challenge for their widespread application is their behavior and reduced gas uptake in wet conditions, attributed to competitive adsorption between gas and water. The current understanding of gas adsorption in wet materials is constrained by studies that utilize only small amounts of powdered porous materials (in the milligram range) within very small reactors (1-5 mL). This leaves a significant gap in knowledge about gas adsorption behaviors in larger reactors and when MOF sample sizes are increased (to the gram scale) for scaling up the process. Additionally, there is a notable dearth of experimental research in situations where MOFs are heavily saturated with water. To address these gaps, this study measures CH4 adsorption in MOFs under conditions of high moisture content, using larger samples of MOFs (in grams) and a large volume reactor. We selected commercially available MOFs, including HKUST-1, ZIF-8, MOF-303, and activated carbon. A high-pressure isotherms (at T = 274.15 K) using volumetric approach were measured to qualitatively compare the moles of gas adsorbed under both dry and wet conditions across different MOFs and weights. Experimental results show that the presence of water led to a decrease in total CH4 mmol adsorption in MOFs, with a more significant decrease observed in hydrophilic MOFs compared to hydrophobic ones. For hydrophilic MOFs, presence of crossover isotherms at crossover pressure provided evidence of water's conversion to hydrate and its positive role in enhancing total gas uptake, which varied among different hydrophilic MOFs. Oversaturated MOFs showed a larger deviation between dry and wet cases at higher pressures. The high-pressure isotherm data confirm the positive role of hydrophilic MOFs in the conversion of water to hydrate in oversaturated MOFs when MOFs sample size is large.

This study investigated the impact of chitosan (CH, 1%) and aloe vera gel (AL, 30%) edible coatings on the preservation of blue honeysuckle quality during a 28-day storage at -1°C. Coating with CH, AL, and CH+AL led to notable enhancements in several key attributes. These included increased firmness, total soluble solids, acidity, pH, and antioxidant capacity (measured through DPPH, ABTS, and FRAP assays), as well as the preservation of primary (ascorbic acid) and secondary metabolites (TPC, TAC, and TFC). These coatings also resulted in reduced weight loss, respiration rate, color, abscisic acid, ethylene production, and malondialdehyde content. Notably, the CH+AL treatment excelled in preserving secondary metabolites and elevating FRAP-reducing power, demonstrating a remarkable 1.43-fold increase compared to the control after 28 days. Overall, CH+AL exhibited superior effects compared to CH or AL treatment alone, offering a promising strategy for extending shelf life and preserving quality of blue honeysuckle during storage.

Milled MgH2, NaAlH4, MgH2–10NaAlH4, MgH2–30NaAlH4, MgH2–50NaAlH4, and MgH2–2Ni-10NaAlH4 samples were prepared by milling in hydrogen atmosphere (reactive mechanical milling, RMM). Decomposition temperatures of milled MgH2, NaAlH4, MgH2–10NaAlH4, and MgH2–30NaAlH4 were examined in a Sieverts-type hydrogen-absorption and release apparatus, in which the hydrogen pressures were kept constant during hydrogen absorption or release. As the content of NaAlH4 in the sample increased, the temperature at the highest peak in the ratio of increase in Hr to increase in T, dHr/dT, versus T curve decreased. The higher content of NaAlH4 is believed to have made effects of reactive mechanical milling stronger. Effects of the NaAlH4 content on the temperatures of intermediate reactions were studied for MgH2 – NaAlH4 composites. Phase formation in the cycled MgH2–50NaAlH4 were investigated. The hydrogen-storage properties of MgH2–30NaAlH4 were compared with those of Mg-based alloys in which oxide, halides, or fluoride was added.

Soil nitrite (NO2‒) is an important reactive intermediate in many nitrogen transformation processes, but it is unstable under acidic conditions. Canonical extraction method of soil NO2‒ with potassium chloride (KCl) solution greatly underestimates its concentration. In order to reflect the concentration more accurately, we optimized the extraction method of soil NO2‒ in this study. Moreover, soil ammonium (NH4+) and nitrate (NO3‒) were also systematically investigated to achieve efficient extraction of soil inorganic nitrogen. The results showed that un-buffered KCl significantly underestimated soil NO2‒ concentration compared to DIW. The highest recovery of NO2‒ was obtained by extracting with DIW at 10 min of oscillation for three soils. Compared with DIW, the concentration of NH4+ and NO3‒ in soil extracted from KCl solution increased significantly. Furthermore, the soil inorganic nitrogen content of extracts stored at 4°C for one day were closer to directly measurements of fresh samples than the other storage methods. Overall, the recommend analysis method for soil NO2‒ was extracted by DIW, oscillated for 10 min, and filtered by a 0.45 µm filter, and soil NH4+ and NO3‒ were extracted with KCl solution and oscillated for 30 min. The extract should be stored at 4°C and analyzed within 24 hours.

Fresh-cut apple is commonly known as minimally processed agriculture products because of their convenience and ease of consumption. However, during storage, the quality of the apple rapidly changes after the cutting process due to enzymatic and non-enzymatic processes. This study aimed to monitor the quality changes of fresh-cut apples at various temperatures and different types of products in the application of a cold chain system during distribution and storage. The results showed that the total viable count in fresh-cut apples initially differed between apple only and mixed products (apple, orange, and tomato) during storage (p &lt; 0.05). Moreover, there are no significant differences (p &gt; 0.05) in physicochemicals except firmness, titratable acidity, and pH, which are highly correlated to microbial growth (total viable count and total coliform number). Furthermore, the optimal temperature for extending the shelf-life of fresh-cut apples was at 4°C.

More water utilities are adopting Aquifer Storage and Recovery (ASR) to balance long-term water supply and demand. Due to large implementation and operation costs, ASR projects need to be optimized, particularly for energy use, which is a major operating expense. This study examines the relationships among energy use, recharge, and recovery at two ASR projects in the western United States. The major finding is an economy of scale for recovery processes, but not for gravity-fed recharge processes. The economy of scale found is as follows: the energy intensity recovered decreases with volume. This suggests it is more energy-efficient to recover large volumes of water in one interval instead of recovering smaller volumes at more frequent intervals. The H2Oaks recovery process experienced a 78% decrease in energy intensity from 0 to 50,000 m3 recovered, while the Sand Hollow site experienced a 43% decrease in energy intensity from 0 to 50,000 m3 recovered. Statistical analyses of the recovery process showed p values lower than 0.0001, R2 values between 0.43 and 0.57, and a RMSE value between 0.55 and 2.1, indicating the presence of a moderate correlation between energy and volume. This economy of scale has been observed in multiple instances in water and wastewater treatment. This finding not only has applications to ASR but also all recovery or recharge wells, whether or not they are paired with each other. Furthermore, this study confirms the need for more reliable and accessible energy data to fully understand the implications of the energy–water nexus.

New ways of generating energy are currently being discussed, with a transition from traditional primary sources to more environmentally friendly options, particularly renewables. Energy storage is also closely related to this transition. Battery storage currently dominates this area. However, flywheel energy storage system (FESS) technology offers an alternative that uses stored kinetic energy to be transformed into mechanical energy and, using a motor-generator, electrical energy. FESS technology is thus flexible and can be applied in different industrial applications. The management of the technology of recycling W-MMC waste material from other products and the subsequent trial production of high-strength W-MMC material with a density of more than 17 500 kg/m3 from recycled powders allowed to test the limits of the so-called "heavy" flywheels used in rotor production. Materials with densities ≥ 7 800 kg/m3, and operating at lower to medium speeds up to 20 000 rpm. The results achieved lead to the conclusion that the developed recycled materials of the W-MMC type with a density ≥ 17 500 kg/m3, with a yield strength of 1 200 - 1 700 MPa depending on the production method, can be used as a substitute for the structural steels used today, without an enforced reduction of the maximum allowed rotor speed due to exceeding the maximum allowed stress.

To handle the huge amount of data generated by IoT devices, Big Data processing tools make it easier. This paper discusses the Big Data concept and its main V’s characteristics. It further describes IoT-enabling technologies; nominally cloud computing such as SaaS and PaaS. The centralization and infrastructure of Big Data systems, and how Cloud Computing gives a platform access to the data from anywhere. The paper explores IoT with big data architectural solutions for various use cases across the healthcare and transportation sectors.

Traditional lithium-ion batteries cannot meet the high flexibility and bendability requirements of modern flexible electronic devices due to the limitations of their electrode materials. Therefore, the development of high-performance flexible energy storage devices is of great significance for promoting flexible electronics. In recent years, one-dimensional flexible fiber lithium-ion batteries have been rapidly developed due to the advantages of high flexibility and bendability. However, it is still a big challenge to realize 1D flexible fiber lithium-ion batteries with excellent electro-chemical properties and good mechanical performance. In this work, a reduced graphene ox-ide-based printing ink is proposed to fabricate flexible Li4Ti5O12/graphene fiber electrodes through a 3D printing assembly strategy. It is noteworthy that the green reducing agent vitamin C was used to reduce graphene oxide in one step, which improved the conductivity of the fiber elec-trode. Furthermore, a 3D conductive network is constructed inside the fiber electrodes due to the high specific surface area of reduced graphene oxide, which enhances the electronic conductivity and ion mobility. The fiber electrode not only has good mechanical performance, but also has ex-cellent electrochemical properties. Equally important, the method is simple and efficient, and the working environment is flexible. It can precisely control the shape, size and structure of the one-dimensional fiber flexible electrode, which is of great significance for the development of fu-ture flexible electronic devices.

Introduction: Mucopolysaccharidosis type I (MPSI) is an autosomal recessive lysosomal storage disorder characterized by deficient or absent α-L-iduronidase (IDUA) enzyme activity due to pathogenic variants in IDUA gene. Early treatment with hematopoietic stem cell transplantation and/or enzyme replacement therapy is associated with improved outcomes in this progressive multisystem disease. The diagnosis is usually delayed due to late presentation and nonspecific symptoms resulting in high morbidity and mortality. The incidence of MPSI in US is estimated to be 0.26:100,000, however, it is unknown in Kuwait. This pilot study was undertaken to screen MPSI in all Kuwaiti neonates born at Farwaniya Hospital over a period of 12-months. This study examined the incidence of MPSI in a major center in Kuwait for inclusion in the national newborn screening program to enable its early detection and adequate treatment. Methods: All Kuwaiti neonates born at Farwaniya Hospital, Kuwait from December 2021 to December 2022, were screened for MPSI. The screening consisted of determining IDUA enzyme activity in dried blood spots (DBS)-derived samples by Tandem Mass Spectrometry. A follow-up genetic analysis of IDUA gene is planned to screen the cases with diminished IDUA enzyme activity as second-tier testing. Results: A total of 618 newborns, including 331 (54%) males and 287 (46%) females, were screened. Twenty of them had deficient IDUA enzyme activity but showed negative genetic testing for IDUA. However, we have diagnosed one additional female baby with MPSI, who belonged to Farwaniya Hospital, but the parents chose to deliver in a private hospital. She presented at age three months with recurrent upper airway infections, snoring and extensive Mongolian spots. The molecular study revealed previously reported pathogenic nonsense variant in IDUA c.1882C>T; p.(Arg628Ter), associated with severe phenotype. That being included, MPSI is estimated to be about 0.3% among tested females and 0.2% of all screened cases in Kuwait. Conclusion: Our study is the first to evaluate the incidence of MPSI in Kuwait. Given the single center, small number of screened babies and the short study duration thus far, it is premature to calculate the incidence of MPSI. It is anticipated that as the study continues and more infants are examined, we would be able to estimate the incidence of this disease in our population correctly. Further studies including screening newborns in all maternity hospitals in Kuwait are needed to calculate the actual incidence of MPSI. Our data supports including MPSI in national newborn screening program to allow early initiation of treatment and thus improve disease outcome.

The paper concludes that the choice of charging strategy depends on the specific requirements and limitations of the off-grid solar PV system, and that a careful analysis of the factors that affect performance is necessary to identify the most appropriate approach. Also provides valuable insights for designing and optimizing off-grid solar PV systems, which can help to improve the efficiency, reliability, and cost-effectiveness of these systems.

Hydrogen is believed to be the principal domain of sustainable energy drive as an alternative to fossil fuels. Unlike the existing standards and knowledge for other fuels, the integrity of sealing and storage materials under the hydrogen environment is not comprehensively studied due to the comparatively new technology and lack of standard laboratory protocols. Typically, storage and polymer materials used as sealing experience degradation and damage in different ways over time in the exposure of hydrogen at different operating conditions, called aging. Improved understanding of the physical and chemical mechanism of degradation due to gaseous hydrogen atmosphere; helps to select and develop the materials best suited to carrier and sealing for respective applications. Damage to materials from aging is inevitable in high-pressure hydrogen gas exposure. This review discusses the mechanism of different categories of aging of storage and sealing materials under the hydrogen environment. Also, the article approaches discussing different laboratory test methods for each type of aging simulation. It covers the limitation of current research on determining material integrity through existing techniques of aging experiments and also explores the latest development. Important improvements are suggested in terms of materials development and testing procedures to meet the existing knowledge in the literature.

We investigated new anodic coloring materials that are used as ion storage layers in complementary energy storage electrochromic devices (ESECDs) to enhance their electrochromic storage performance. In this study, we fabricated counter electrodes (ion storage layers) using IrO2 doping NiO (Ir: NiO) film through cathodic arc plasma (CAP) with varying surface charge capacities. We investigated the influence of MoO3-doped WO3 (Mo: WO3) film by various Ar/O2 gas flow ratios (1/4, 1/5, and 1/6). The ESECDs used in the demonstration were 10×10 cm2 in size. They achieved optical transmittance modulation of Ir: NiO- ESECDs (glass/ITO/ Mo: WO3/gel-polymer electrolytes/ Ir: NiO /ITO/glass), ΔT=53.3% (from Tbleaching (66.6%) to Tcoloration (13.1%)). The ESECDs had a quick coloration time of 3.58 seconds, a rapid bleaching time of 1.24 seconds, and high cycling durability. It remained at 45% transmittance modulation even after 3000 cycles. New anodic materials can provide an alternative to traditional active materials for bi-functional electrochromic batteries.

Compared to other 2D materials, MBenes are at an early stage in both experimental and theoretical approaches. However, the wide range of possible 2D structures leads to novel and challenging properties and their consequent applications. From all the possible stoichiometries, we have performed a theoretical study of orthorhombic and hexagonal M2B2 MBenes in the framework of the Density Functional Theory. We have found that both symmetries of Cr2B2, Fe2B2, and Zr2B2 show a metallic behavior and could be grown under certain conditions, as they are demonstrated to be dynamically stable. Moreover, the values of the magnetic moment, in specific ferromagnetic cases exceeding 2.5 μB/M2B2, make them suitable as robust 2D magnets. All our findings represent an important step in the understanding of MBenes and open several windows to future research in fields like energy conversion and storage, sensing, catalysis, biochemistry, or nanotechnology, among others.

Olive mill wastewater (OMW) has serious environmental problems considering its high organic matter, especially its phenolic compounds. The OMW application in crop protection is an alternative environmentally eco-friendly method reducing the chemicals pesticides impact on human health and environment. The present work aimed to study the antifungal activity of fresh and stored OMW and its ethyl acetate extract against phytopathogenic fungi: Syncephalastrum racemosum (S. racemosum), Paramyrothecium roridum (P. roridum), Fusarium oxysporum (F. oxysporum) and Verticilium dahlia (V. dahlia). The OMW was stored at 25 and 45 °C for 3 months. Fresh and stored OMW were used non-sterile, sterile and centrifuged. Phenolic and flavonoid compounds were extracted and identified by HPLC analysis. High inhibition of studied fungi was shown by fresh OMW and its derivative compounds, while OMW storage, sterilization, and centrifugation increased mycelium growth of studied fungi, especially S. racemosum that showed a relative resistance against stored OMW effect and its ethyl acetate extract. Under storage conditions, some phenolic and flavonoid compounds disappeared (resorcinol and vanillic acid), while the concentration of other compounds increased (gallic acid, chlorogenic acid and quercetin). This work highlighted the ability to use fresh OMW as a bio-agent to protect plants from fungi diseases.

Energy storage systems (ESSs) are the key elements to improve the operation of power systems. On the other hand, these elements challenge the power system planners. The difficulties arise as a result of the ESSs' economic and technological features. The cycle life of ESSs is a critical aspect that influences the choices made during expansion planning processes. In this manuscript, we have focused on a new model for the expansion planning of ESSs considering the impacts of technical properties, such as the cycle life and depth of discharge. For this purpose, the proposed model consists of the hourly operation planning of ESSs in the sample days of year. A new indicator is proposed to determine the daily charging/discharging cycles of ESSs. Numerical results show the ability of the proposed model to determine the optimal technology and capacity of ESSs.

Transportation, environmental conditions, quality of human life within smart cities, and system infrastructure have all needed practical and dependable smart solutions as urbanization has accelerated in recent years. In addition, the emerging Internet of Things (IoT) provides access to a plethora of cutting-edge, all-encompassing apps for smart cities, all of which contribute significantly to lowering energy consumption and other negative environmental impacts. For smart cities to meet the challenge of using less energy, the authors of this research article suggest planning and implementing an integrated power and heat architecture that puts renewable energy infrastructure and energy-storage infrastructure at the top of the list. To address these issues, we describe a smart proposed NEOSRD architecture that uses a distributed smart area domain to optimize renewable demand energy in a smart city across a wide area network. The energy requirements of desalination procedures are negligible when compared to the total local energy consumption and transportation, a feat accomplished by the proposed NEOSRD system. Here, the computational model shows how the established system is a valuable response to our problems and a cost-effective strategy for creating smarter structural elements that cut down on overall smart cities' energy costs.

In this research, Cellulose Nanofibers (NFC) modified with a eutectic of lauric acid (LA) was prepared as a new form-stable phase change material (NFC-LA). Thermal properties of this composite were investigated by Differential Scanning Calorimetry (DSC). The results revealed that the melting temperature and latent heat of NFC/LA were 21.56 °C and 88.5 J/g, respectively; and the super cooling degree for the NFC-LA composite decreased to 13.99 °C when compared to 20.28 °C of the pure lauric acid. Natural clay was purified and modified with Cetyltrimethyl ammonium bromide (CTAB) to prepare organoclay. Through FTIR spectra, we have confirmed that the clay was successfully modified. The PCM-composite was then added to the organoclay to obtain a new composite denoted NFC-LA-OC. this latter was added to cement and was investigated as a reinforcement material in cement mortars for thermal energy storage application. The prepared material can both solve the leakage problem associated to the phase change material, and reduce or even avoid the use of heating and air conditioning systems, which are energy-intensive systems, and therefore reduce energy consumption.

Carbon Capture and Storage (CCS) is a new technology considered to have the potential to decarbonise economies. However, nationally and internationally the use of CCS has also been raising concerns about its potential global risks and adverse impacts on the environment. CCS was part of the discussions at the 4th United Nations Environment Assembly (UNEA) in March 2019 and in side-events in the 26th UN Climate Change Conference which took place in Glasgow in November 2021. The UK Government aims to deploy CCS at scale during the 2030s, subject to cost reduction. At the same time the UK Government has recently enacted the Environment Act 2021 which provides a set of five environmental principles: the integration principle, the principle of preventative action, the precautionary principle, the rectification at source principle and the polluter pays principle. This work seeks to analyse the application of the UK environmental law principles to carbon capture and storage policies in the UK and its balance with other considerations. Given the concerns surrounding the use of CCS, the debate about its legality may arise in the UK and in other countries. To this end, this paper initially carries out a systematic review of CCS policy documents to discover the policy considerations which support the development of CCS. It then examines the application of the UK environmental law principles to CCS initiatives and its balance with other considerations, such as reduction of carbon emissions, security of energy supply, economic growth and technological leadership. In doing so, this paper aims at contributing to the debate surrounding recent technological developments which have been utilised to help address climate change and some of the legal challenges emerging through the use of CCS under UK environmental law.

Water scarcity is a significant challenge facing Jordan today. It is a challenge in all areas that use water, and it has become certain that water is the critical factor in the population/resources equation. The water resources in Jordan have become limited with the noticeable increase in the population, mostly resulting from forced migrations in neighboring countries because of the wars and until our time. The rising natural population growth rate, along with the massive influx of refugees, has turned into a state of disproportion between the daily consumption of the population and the amount of water available. That Jordan shares most of its surface water resources with neighboring countries has exacerbated the situation. The current use of water already exceeds its renewable supply. Excessive withdrawal from aquifers, which leads to a lowering of the water table and deterioration in water quality, covered the deficit. This paper focuses on assessing the water situation in Jordan, mainly evaluating this problem and the solution being considered, the true basis for a sustainable water solution requires awareness by the population, and several governmental and non-governmental organizations are actively involved in educating residents about water shortages. The most important and 'actionable' elements of comprehensive water solutions are discussed in this paper, and these elements exist, develop extra water supplies, water harvesting, water desalination, proper wastewater reuse in the agricultural sector, and reduce the demand for drinking water. This research provides specific recommendations to address the shortage of water resources in the Kingdom and highlights the importance of water conservation and optimal use.

Two sets of initial conditions are used in the investigation of capital return rate and carbon storage in boreal forests. Firstly, a growth model is applied in young stands as early as the inventory-based model is applicable. Secondly, the growth model is applied to observed wooded stands. Four sets of thinning schedules are investigated in either case. First, the capital return rate is aspired without any restriction. Second, the number of thinnings is restricted to at most one. Third, thinnings are restricted to the removal of only trees thicker than 237 mm. Fourth, commercial thinnings are omitted. The two sets of initial conditions yield similar results. The capital return rate is a weak function of rotation age, which results in variability in the optimal number of thinnings. Reducing the number of thinnings to one increases timber stock but induces a capital return rate deficiency. The deficiency per excess volume unit is smaller if the severity of any thinning is restricted by the removal of large trees only. Omission of thinnings best applies to spruce-dominated stands with stem count less than 2000/ha. Restricted thinning intensity applies to deciduous stands and dense pine stands. The albedo effect increases the benefits of restricted thinnings and increased clearcuttings instead of contradicting the carbon storage.

Traditionally Moringa is known as mystical miracle tree or the tree of life. Soup can be classified as an appetizer, warm food during cold and sick. Moringa oleifera pods have been procured from College of Agriculture, JNKVV, Jabalpur. The present investigation is planned with objectives to standardize best combination of for the development of instant soup mix, to evaluate various quality parameters, to evaluate the storage stability and cost estimation of product. Protein in instant soup is ranged from 9.76 to 11.89 percent in different formulations of instant soup mix. Formulation MPP4 (11.89) had significantly maximum protein content followed by MPP3, MPP2, MPP1 and Control with the minimum protein content. The original instant soup mix (control) exhibited highest carbohydrate content (61.52%) followed by MPP1, MPP3, MPP4, and MPP2 with lowest content. The evaluated scores of control for colour and appearance, taste, flavour, consistency, after taste and overall acceptability are 8.36, 8.50, 8.60, 8.90, 8.76 and 8.63 respectively

The zebrafish Danio rerio is suitable to study gametes as a model organism. There were &gt; 70% of zebrafish spermatozoa activated, because they were contaminated with urine or excrement. The movement of spermatozoon in water was propagated along the flagellum at 16 s after sperm activation, then damped from the end of the flagellum for 35 s and fully disappear at 61 s after activation. For artificial fertilization, milt must be added to an extender, which stops the movement of sperm and keeps the sperm motionless until fertilization. E400 was shown to be the most suitable extender as it allows to store sperm for fertilization for 6 to 12 h at 0-2oC. Sperm motility decreased only to 36% at 12 h post stripping (HPS) for E400 extender and to 19% for Kurokura extender. To achieve an optimal level of fertilization and hatching, a test tube with a well-defined amount of 6,000,000 spermatozoa in E400 extender per 100 eggs and 100 µl of activation solution has proved to be more successful than using a Petri dish. The highest fertilization and hatching rates reached 80% and 40-60%, respectively, with milt stored for 1.5 h in E400 extender at 0-2oC.

Following an updated outlook of global energy production and utilization, we show through selected examples from both developing and developed countries how distributed generation from renewable energy sources, and from solar energy in particular, is the key solution to ending energy poverty across the world. Guidelines aimed at policy makers suggest a systems view of energy that will be instrumental in guiding the transition from fossil fuels to combustion-free renewable energy for all energy end uses.

Phase Change Materials (PCMs) are latent heat storage media with high potential of integration in building structures and technical systems. Their solid-liquid transition is commonly utilized for thermal energy storage in building applications. It also means that some kind of encapsulation is necessary. This is often solved with metal containers that also have high thermal conductivity and resistance to mechanical damage enhancing the performance these so called latent heat thermal energy storage (LHTES) systems. However selection of suitable metal is rather challenging. It depends, among other things, on the elimination of undesirable interaction between storage medium and surrounding metal. Heat storage medium must be reliably sealed in metal container especially when the storage system is integrated in systems like domestic hot water storage tanks, where PCM leaks can negatively affect human health. The aim of this study was evaluation of interaction between selected commercially available organic and inorganic PCMs and metals. The evaluation is based on the calculation of corrosion rate and use gravimetric method for determination of the weigh variations of the metal samples. Results show that aluminium is the most suitable container material with lowest mass loss and suffered only minimal visual changes on the surface after prolonged exposure to PCMs.

The theoretical limits of water sorbate based chemical sorption heat storage are investigated in this study. First, a classification of \textit{thermochemical heat storage} is proposed based on bonding typology. Then, thermodynamics of chemical solid/gas sorption is introduced. The analysis of the reaction enthalpy from the literature indicates that this value is only slightly varying for one mole of water. Using this observation, and with the help of thermodynamical considerations, it is possible to derive conclusions on energy efficiency of closed and open heat storage systems. Whatever the salt, the main results are 1) the energy required for evaporation of water is, at least, 65% of the available energy of reaction and 2) the maximum theoretical energy efficiency of the system is about 1.8.

Power system decentralization has been an emerging topic for the past decade in an effort to improve power quality and environment protection via increased integration of renewable energy sources. Towards these objectives, decentralized microgrids have been proposed and thoroughly investigated in terms of technical capabilities and economic performance. In fact, the planning and actual operation of small-scale, decentralized microgrids has started in countries such as Canada, Japan, USA, UK and other countries. It is expected that the research in this area will progress and eventually take over the existing paradigm of large-scale power generation in the future. These small-size decentralized microgrids could be connected with nearby microgrids under normal operating conditions, but under special events, such as natural or man-made disasters, they would be disconnected and run in islanded mode. Under such high impact – low probability events, the microgrid must have resiliency to successfully re-connect with other microgrids and the main grid. In this paper, an Energy Management System (EMS) for a microgrid having a resiliency function, allowing to operate under islanded mode after an accident, is proposed. The proposed tool, called Resilient Energy Management System (ResEMS), aims at procuring reserve power into the microgrid’s Battery Energy Storage System (BESS) effectively, by importing it from the nearby connected power system. The accident is assumed to be a predictable natural disaster, which means that the accident occurrence time, duration and level of damage can be estimated. The proposed ResEMS has been applied to a microgrid comprising of a BESS, a diesel generator and several photovoltaic devices. The simulation results verify its beneficial operation.

Thermal energy storage (TES) is a key technology to enhance the efficiency of energy systems as well as to increase the share of renewable energies. In this context, the present paper reports a literature review of the recent advancement in the field of adsorption TES systems. After a first introduction about different heat storage technologies, the adsorption TES working principle is explained and compared to the other technologies. Subsequently, promising features and critical issues at material, component and system levels are deeply analyzed and the ongoing activities to make this technology ready for marketing are introduced.

Nickel nitrate diammine, Ni(NH₃)₂(NO₃)₂, can be synthesised from the thermal decomposition of the nickel nitrate hexammine, Ni[(NH₃)₆](NO₃)₂. The hexammine decomposes in 2 distinct steps; the first releases 4 equivalents of ammonia while the second involves the release of NO_x, N₂ and H₂O to yield NiO. The intermediate diammine compound can be isolated following the first deammoniation step or synthesised as a single phase from the hexammine under vacuum. Powder X-ray diffraction (PXD) experiments have allowed the structure of Ni(NH₃)₂(NO₃)₂ to be solved for the first time. The compound crystallises in orthorhombic space group Pca2₁ (a = 11.0628 (5) Å, b = 6.0454 (3) Å, c = 9.3526 (4) Å; Z = 4) and contains 11 non-hydrogen atoms in the asymmetric unit. Fourier Transform Infrared (FTIR) spectroscopy demonstrates that the bonding in the ammine is consistent with the structure determined by PXD.

A temperate deep lake, Lake Kuttara, Hokkaido, Japan (148 m deep at maximum) was completely frozen every winter in the 20th century. However, unfrozen conditions of the lake over winter occurred four times in the 21st century, which is probably due to global warming. In order to understand how thermal regime of the lake responds to climate change, its heat storage change was calculated by estimating heat budget of the lake and monitoring water temperature at the deepest point for September 2012–June 2016. As a result, temporal change of the heat storage from the heat budget was very consistent with that from the direct temperature measurement (determination coefficient R² = 0.827). The 1978–2017 data at a meteorological station near Kuttara indicated that there are significant (less than 5% level) long-term trends for air temperature (0.024 °C/yr) and wind speed (−0.010 m/s/yr). A sensitivity analysis for the heat storage from the heat budget estimate and an estimate of return periods for mean air temperature in mid-winter allow us to conclude that the lake could be unfrozen once per about two year in a decade.

Energy storage systems (ESS) are penetrating into various sections of power system through different applications. ESS can be used either as a buffer for intermittent renewable energy sources or as a stand-alone distributed storage for load shifting. ESS use different types of storage devices such as lead-acid batteries, lithium ion batteries, flow batteries, and super-capacitors. Hybrid ESS consisting of few types of storage devices are also common in practice. Determining the load demand of such ESSs at various instances (charging profile) accurately is indispensable in most of the cases. Capacity loss is common phenomenon that occurs in all types of storage devices because of ageing. Capacity loss has to be accounted while determining the charging profile of storage devices for better accuracy. Data-driven modeling is an attractive approach for determining the load demand of ESS due to the availability of valuable data from smart grid technologies. In this paper, the application of different types of data-driven models to predict the current charging profile of the ESS based on previous charging profiles is examined. The proposed method can leverage on the existing data from smart grid and is a black box modeling approach.

The expansion of renewable energies is progressing strongly. The influence on the power supply networks by the volatility of the infeed must be met with new concepts. In this paper we investigate the possibilities of integrating microgrids as a cooperating unit in the power supply network to support further expansion of RES power plants. In this paper a differentiation of microgrids from similar network structures is established, a classification of proposed groups is made. Then, after the description of simulation of components in a microgrid, with practical advice, an example model is shown, which aids the dimensioning of the components within a microgrid to achieve a specified goal.

This study aims to provide empirical evidence on whether using renewable and non-renewable energy, CO₂ emissions and the resulting changes in temperature and precipitation can alter cereal yields in European Union countries. To this end, a panel data set covering 1992-2021 has been used to analyse the impact of climate change and economic factors on cereal production in European Union countries. The study employed various analytical techniques to understand better the relationship between climate change, energy consumption, and economic growth. These included using annual average temperature and rainfall to measure climate change and energy consumption and economic growth to analyse the economic aspects. To achieve the objective, feasible generalised least squares (FGLS) models with robust standard errors and bootstrap and a quantile regression (QR) model with marginal analysis were employed. The Westerlund cointegration test confirmed the presence of cointegration between cereal production and climate variables, economic growth, and energy consumption. The results indicate that increases in temperature and precipitation may contribute to increased cereal production in European Union countries. In contrast, energy consumption, including renewable energy and CO₂ emissions, may have a nonlinear effect on cereal production. Quantile regression analysis suggests climate change may impact crop yields most in countries with low and moderate cereal production per hectare. Increased CO₂ emissions may increase yields in the initial period, but excessive CO₂ may negatively impact cereal production in the long term. It would be advisable for countries with low and moderate crop productivity to consider implementing technological advances and combating global warming by modernising cultivation methods and making greater use of renewable energy sources.

This study aims to evaluate the climate-change response of greening persistently vacant houses and barren sites in deteriorated high-density residential areas in old downtown metropolitan areas. The current status of building demolition sites in Ami-dong and Chojang-dong, Busan Metropolitan City, was examined. In this area, of the 340 vacant houses from 2017, 246 (72.35%) remained persistently vacant till 2020. In 2020, 213 barren sites were neglected after building demolition. Amongst these sites, 177 (83.10%) were paved with concrete. Persistently vacant houses and barren sites were afforested, and the climate-change response was quantified in terms of flood reduction and CO2 mitigation in four scenarios (current, concrete, ground cover plants, and trees). Runoff analysis was performed using the Korea low-impact development model (K-LIDM) to assess flood mitigation. The tree scenario showed average runoff mitigations of 1.71%, 2.38%, and 3.06% in the long-term, 30-year, and 2-year rainfall scenarios, respectively. Additionally, 3058 deciduous broadleaf trees may be planted in the study area to promote CO2 mitigation. Thus, an additional annual carbon fixation of 62,123.78 kg CO2 may be expected. The greening of vacant houses and demolished sites was effective in all aspects of the climate-change response, and tree-based greening exhibited the most significant effect.

Due to the severe environmental impact of the CO2 emissions associated with the production of Ordinary Portland Cement (OPC) and the increasing demand for this commodity material, the development of alternative products has become a global concern. One alternative to OPC, or alitic-based clinkers, are amorphous-wollastonitic low calcium hydraulic binders (AWLCs). This new class of hydraulic binders, described in the literature for the first time in 2015, may significantly reduce the CO2 emissions associated with its production, resulting from its lower calcium content, but also from the fact that its production technology can be fully electrified. In this paper it is provided a state-of-the-art review, providing a comprehensive description on the latest research, summarizing both the physico-chemical and mechanical characteristics for this type of hydraulic binders, as well as possible routes for its production at an industrial scale.

In the field of embedded systems, energy efficiency is a critical requirement, particularly for battery-powered devices. RISC-V processors have gained popularity due to their flexibility and open-source nature, making them an attractive choice for embedded applications. However, not all RISC-V processors are equally energy-efficient, and it is important to evaluate their performance in specific use cases. This paper evaluates the energy consumption and resource utilization of a new RISC-V processor, RisCO2, and four existing processors - Zero-riscy, Micro-riscy, Ri5cy, and CV32E40P - in a signal demodulation application for NDIR CO2 sensors. The processors were implemented in the PULPino SoC and synthesized using Vivado IDE. The processor named RisCO2 is based on the RV32E_Zfinx instruction set and was designed from scratch by the authors specifically for low-power signal processing applications such as signal demodulation in CO2 NDIR sensors. The other processors are Ri5cy, Micro-riscy, and Zero-riscy, developed by the PULP Platform team, and CV32E40P (derived from Ri5cy) from the OpenHW Group, all of them widely used in the RISC-V community. Our experiments showed that RisCO2 had the lowest energy consumption among the five processors, with a 53.5% reduction in energy consumption compared to CV32E40P and a 94.8% reduction compared to Micro-riscy. Additionally, RisCO2 had the lowest FPGA resource utilization compared to the best-performing processors, CV32E40P and Ri5cy, with a 46.1% and a 59% reduction in LUTs, respectively. Our findings suggest that RisCO2 is a highly energy-efficient RISC-V processor for NDIR CO2 sensors that require signal demodulation. The results also highlight the importance of evaluating processors in specific use cases to identify the most energy-efficient option. This paper provides valuable insights for designers of energy-efficient embedded systems using RISC-V processors.

CO2 has characteristic properties and reactions at converter smelting temperature, and the chemical reaction between CO2 and elements such as C and Si in the molten pool has bubble proliferation and cooling effects, which can effectively improve the kinetic and thermodynamic conditions of converter smelting. Here, an experimental study and industrial test on the application of CO2 in converter smelting were carried out. The smelting effects of Mode-1 and Mode-2 with total CO₂ injection amounts of 229 Nm³ and 196 Nm³, respectively, were compared, and the changes in molten steel and slag compositions, dust removal, and gas are analyzed. The test results show that converter top and bottom blowing CO₂ technology (COMI-B)technology had significant metallurgical advantages over the N-Mode; the dephosphorization rate increased by 4.2%, slag (FeO) content was reduced by 2.04%, end point nitrogen content of molten steel was reduced by 20%, gas recovery increased by 8.29 Nm³/t, and soot production reduced by 14.7%. The results of the study provide reference for the application of COMI-B technology in converters in the iron and steel industry and develop a new path for resource utilization of CO₂.

MXenes are two-dimensional nanomaterials isolated from MAX phases by the selective extraction of the A component —a p-block element. The MAX phase exfoliation energy, Eexf, is regarded as a chemical descriptor of the MXene synthesizability. Here we show, by density functional theory estimations of the Eexf values for 486 different MAX phases, that Eexf decreases i) when MAX is a nitride, ii) when going along a d series of the metal M component, iii) when going down a group of the p-block A element, as well as iv) when having thicker MXene phases. Furthermore, Eexf is found to bias, even to govern, the surface chemical activity, as evaluated here on the CO2 adsorption strength, so that more unstable MXenes, displaying larger Eexf values, display a stronger attachment of species upon.

The paper presents the results of energy and environmental analysis of geothermal CHP plant operation in Polish conditions. As the most favorable, for the geothermal conditions prevailing in Poland, the variant of CHP plant based on Organic Rankine Cycle (ORC) has been taken into consideration. As the case study the existing geothermal well located in the town of Konin in the Wielkopolska voivodship has been chosen. The conceptual design of CHP plant has been proposed and evaluated from energy and environmental point of view. As energy performance criteria the non-renewable primary energy consumption has been chosen. In case of environmental performance carbon dioxide emission has been taken as evaluation criteria. The analysis has been performed for different operating conditions and three working fluids.

Electric vehicles, being able to reduce pollutant and greenhouse gas emissions and shift the economy away from oil products, can play a major role in the transition towards low-carbon energy systems. However, the related increase in electricity demand inevitably affects the strategic planning of the overall energy system as well as the definition of the optimal power generation mix. With this respect, the impact of electric vehicles may vary significantly depending on the composition of both total primary energy supply and electricity generation. In this study, Italy and Germany are compared to highlight how a similarity in their renewable shares not necessarily leads to a CO₂ emissions reduction. Different energy scenarios are simulated with the help of EnergyPLAN software assuming a progressive increase in renewable energy sources capacity and electric vehicles penetration. Results show that, for the German case, the additional electricity required leads to a reduction in CO₂ emissions only if renewable capacity increases significantly, whereas the Italian energy system benefits from transport electrification even at low renewable capacity. Smart charging strategies are also found to foster renewable integration; however, power curtailments are still significant at high renewable capacity in the absence of large-scale energy storage systems.

Biochar application to soil has been proposed as a means for reducing soil greenhouse gas emissions and mitigating climate change. The effects, however, of interactions between biochar, moisture and temperature on soil CO₂ and N₂O emissions, remain poorly understood. Furthermore, the applicability of lab-scale observations to field conditions in diverse agroecosystems remains uncertain. Here we investigate the impact of a mixed wood gasification biochar on CO₂ and N₂O emissions from loess-derived soils using: (1) controlled laboratory incubations at three moisture (27, 31 and 35%) and three temperature (10, 20 and 30°C) levels, and (2) a field study with four cropping systems (continuous corn, switchgrass, low diversity grass mix, and high diversity grass-forb mix). Biochar reduced N₂O emissions under specific temperatures and moistures in the laboratory and in the continuous corn cropping system in the field. However, the effect of biochar on N₂O emissions was only significant in the field, and no effect on cumulative CO₂ emissions was observed. Cropping system also had a significant effect in the field study, with soils in grass and grass-forb cropping systems emitting more CO₂ and less N₂O than corn cropping systems. Observed biochar effects were consistent with previous studies showing that biochar amendments can reduce soil N₂O emissions under specific, but not all, conditions. The disparity in N₂O emission responses at the lab and field scales suggests that laboratory incubation experiments are not reliable for predicting the impact of biochar at the field scale.

Decomposition of natural and synthetic polymeric materials (peat, humates, biochar, strongly swelling hydrogels and other soil conditioners) in a biologically- and chemically- active soil environment inevitably leads to their degradation and ability to improve the structure, water-retention, absorptive capacity and actual fertility of artificial soil constructions in urbanized ecosystems and agro landscapes (constructozems). Quantitative assessment of the biodegradation process using field and laboratory incubation experiments, as well as mathematical modeling, showed the possibility of significant (up to 30-50% per year) losses of organic matter of constructozems and a corresponding deterioration in their quality. Incubation experiments with the analysis of carbon dioxide emission for polymeric materials under given thermodynamic conditions allow to estimate the potential rates of their decomposition (half-life) and their dependence on the dose of inhibitors of microbial activity. Special nomographs provide an opportunity to determine the optimum depth of the arrangement of organic components in soil constructions to ensure their stable functioning during a fixed operating time in urban conditions. The results of the study are useful for geo-engineers and landscaping practitioners.

Developing high performance HVAC system using natural refrigerants including carbon dioxide (CO₂) has been important in respect of environmental preservation and associated technologies. Thus studies to optimize the HVAC (heating ventilation air conditioner) system using natural refrigerants through clarifying the cycle performance characteristics are necessary. The CO₂ heat pump system using air and water sources was consisted to examine its performance characteristics, and by varying conditions of several factors that affect or characterize the system performance like the amount of refrigerant charge, EEV (electronic expansion valve) opening, and internal heat exchanger under cooling mode. The performance characteristics of CO₂ heat pump system were tested by using an air enthalpy calorimeter. In the case of the CO₂ heat pump system without internal heat exchanger, the opening of #3 EEV and #4 EEV was 60% and refrigerant charge amount was 5,600g. However, in the case of that with internal heat exchanger, the best performance was obtained when the opening of #2 EEV is 20%. From the present studies, it was observed that the performance variation and operational characteristics of the CO₂ heat pump system were affected by design factors like refrigerant charge amount, EEV opening, and internal heat exchanger and thereby, the configuration on an optimal operation conditions of the system was enabled.

Incorporating renewables in the power grid presents challenges for stability, reliability, and operational efficiency. Integrating Energy Storage Systems (ESS) offers a solution by managing unpredictable loads, enhancing reliability, and serving the grid. Hybrid storage solutions have gained attention for specific applications, suggesting higher performance in some respects. This paper compares the performance of hybrid energy storage systems (HESS) to single battery, evaluating their energy supply cost and environmental impact through optimization problems. The model generates an optimized dispatch, minimizing cost or environmental impact of supplying energy to a generic load while considering battery degradation. Seven technologies are assessed, with an example applied to an industrial site contrasting vanadium redox flow (VRFB) and lithium batteries considering the demand of a local load (building). The results also indicates that efficiency and degradation curves have the highest impact in the final costs and environmental functions on the various storage technologies assessed. For the simulations of the example case, a single system only outperforms the hybrid system in cases where lithium efficiency is higher than approximately 87% and vanadium is lower approximately 82%.

The benefits of cycling as a sustainable transportation mode are widely recognized. Cycling to work offers numerous advantages for individuals, employers, the environment, and society, ranging from improved physical health, wellbeing, and productivity to enhanced public health and reduced carbon emissions. Many governments around the world have implemented various policy measures, interventions, and initiatives to promote cycling. Some cities and towns have encouraged workplaces to provide bike-friendly amenities, such as secure bike parking/storage and shower and changing facility (referred to as end-of-trip facilities), to accommodate cyclists and motivate more employees to embrace sustainable transportation options. However, the presence or absence of such amenities has been found to both positively influence cycling behavior or deter some individuals from cycling to work. Despite the desirability of these amenities, the number of office buildings equipped with bike storage and shower/changing facility remains small, and their economic value is not well understood. In this paper, we aim to investigate whether the presence of cycling-supportive facilities could add value to office buildings. Specifically, we conduct a study using data from office buildings across England as of the end of 2021. We employ hedonic techniques to examine whether office buildings with bike storage and/or shower facility command a rent premium and whether the existence of a rent premium for bike storage and/or shower facility vary by location and across regions in England, independently from any premium associated with BREEM certification. We find that the buildings with bike storage and shower facility secure rent premiums respectively. The level of rent premiums varies with location and regions. The variations of premium are driven by the shortage of the supply of these facilities.

In an IoT system, the sheer volume of data generated by numerous sensing devices necessitates a well-designed scheme for storing and retrieving data efficiently, enabling streamlined data processing and analytics. One promising storage architecture involves utilizing solid-state drives (SSDs) to cache data from hard disk drives (HDDs), thereby creating an SSD-based caching storage system. To further enhance access performance, it is possible to employ readahead techniques to minimize data access latency. However, the existing Linux readahead scheme falls short in fully leveraging SSD-based caching storage systems. We address this limitation by introducing a novel cross-layered readahead architecture that effectively communicates with the VFS layer, the file system layer, and the block I/O layer. This communication facilitates the acquisition of readahead timing, readahead data continuity, and readahead data location, respectively. To guide prefetching decisions, our architecture analyzes the degree of data access sequentiality, the performance model of the target storage device, and the access patterns of the I/O workload on the corresponding storage device. The implementation of this new architecture in the Linux kernel yields promising experimental results, demonstrating its robustness by consistently outperforming the stock Linux kernel. Notably, our architecture reduces the total execution time of the stock Linux kernel by up to 49%, except in cases of random workloads where both the stock Linux kernel and our architecture exhibit similar performance.

Ni-rich layered cathodes are regarded as a potential candidate for high energy-density lithium-ion batteries, but their high sensitivity to air during storage and poor thermal stability are a vital challenge for large-scale applications. In this paper, an effective solid-solution strategy was proposed to improve the surface and structural stability of Ni-rich layered cathodes by introducing Li2MnO3. The structural analysis results indicate that the formation of Li2CO3 inert layers on Ni-rich layered cathodes during storage in air is responsible for the increased electrode interfacial impedance, thereby resulting in the severe deterioration of electrochemical performance. The introduction of Li2MnO3 can reduce the surface reactivity of Ni-rich cathode materials, playing a certain suppression effect on the formation of surface Li2CO3 layer and the deterioration of electrochemical performances. Additionally, the thermal analysis results show that the heat release of Ni-rich cathodes strongly depends on the charge of states, and Li2MnO3 can suppress oxygen release and significantly improves the thermal stability of Ni-rich layered cathodes. This work provide a method to improve the storage performance and thermal stability of Ni-rich cathode materials.

As for their large surface area and pore volume, three-dimensional covalent organic frameworks (3D COFs) have emerged as competitive porous materials. However, due to the structural dynamic behavior particularly for imine-linked 3D COFs, potentially unlock their potential for gas storage application. Herein, we showed a pre-locked linker strategy introduces breaking dynamic behavior in 3D COFs. A predesigned planar linker based 3,8-diamino-6-phenylphenanthridine (DPP) was prepared to produce non-dynamic 3D JUC-595, as benzylideneamine moiety in DPP locked the linker flexibility and restrict the molecular-bond rotation of the imine linkages. Upon solvent inclusion and release, the PXRD profile of JUC-595 remained intake, while JUC-594 with flexible benzidine linker experienced crystal transformation due to framework contraction-expansion. As a result, the activated JUC-595 achieved higher surface areas (754 m² g-1) than that of JUC-594 (548 m² g-1). Furthermore, improved CO2 and CH4 storages were also seen in JUC-595 compared with JUC-594. Impressively, JUC-595 recorded high normalized H2 storage capacity that surpass other reported high surface area 3D COFs. This works shows important insight on manipulating structural properties of 3D COF to tune the gas storage performance.

Saudi Arabia is a prominent producers of dates, with 1.6 million tons annually. There is a need to evaluate physical properties and quality of fruits non-destructively and then be modeled and predicted throughout the storage period. The aim of the current study was to generate a quality index (Qi) and Near-infrared spectra (NIR) models non-destructively to predict properties of Barhi dates fruits including objective and sensory evaluations. The engineering properties of Barhi dates were measured and modeled with quality index (Qi) based on NIR of fresh Barhi fruits (hardness, color, TSS, pH, and sensory evaluations) and during storage in cold, ambient, and controlled at-mosphere (CA) for up to four months. The prediction of Qi is non- destructively based on NIR utilizing PLSR and ANN data analysis. The results showed that the Qi generated corresponds with high precision to the characteristics of the examined fruits through the duration of the storage period with R2 of 0.96. The NIR spectrum proves to be an efficient method to evaluate the Barhi fruits' quality index. where ANN was found to be more suitable than PLSR analysis. Thus, NIR can be utilized to accurately predict the Qi of fruits quality effectively throughout the handling, processing, transporting, storage, and retail sector supply chain.

Accurate determination of the concentration of alcohols and their metabolites is important in forensics and in several life science areas. A new method has been developed to quantify alcohols and their oxidative products using a headspace gas chromatography- mass spectrometer and isotope-labelled internal standards. This work demonstrates the application of this method, specifically in quantifying the concentration of oxidative products of alcohol and other minor alcohols found in hand sanitizers, which have become an essential household item since the COVID-19 pandemic. Apart from the major component, the minor alcohols found in hand sanitizers include methanol, isopropanol, and n-propanol. In ethanol-based hand sanitizers, a significant amount of acetaldehyde was observed as an oxidation product, while in isopropanol-based hand sanitizers, acetone was observed. The concentration of acetaldehyde in ethanol-based hand sanitizers significantly increased with storage time and temperature, whereas no such increase of acetone concentration was observed in isopropanol-based hand sanitizers with storage time and temperature.

The Limpopo estuary mangrove forest covers about 928 ha, however 382 ha remain intact and 546 ha were degraded after the 2000 floods. Mangrove replanting campaigns have been carried out at the site. This article aims to evaluate the structure and carbon pool of aboveground and belowground living biomass and soil carbon in natural and replanted mangrove forests (2016, 2014 and 2010). The methodology consisted of selecting 40 strata where structural data were collected. Living biomass above and below ground and soil carbon was obtained based on the methodology described by Kauffman and Donato (2012). The results showed that A. marina was the most observed species in all study areas. The carbon reserve of living biomass above and below ground in the natural forest was 67.9±100.9 MgCha -1 and 65.0±77.1MgC ha -1 , respectively; and in the planted forests (2016, 2014, 2010) it was 1.1±0.5MgCha-1 and 2.1±1.0MgCha-1, 1.8±1.0MgCha-1 and 3.6±2.0MgCha-1, 3.7±2.0MgCha-1 and 5.3±2.5MgCha-1 . Soil carbon reserve was 229.4±119.4 MgCha-1 in natural forest and 230.3±134.8 MgCha-1 , 234.8±132.7MgC ha-1, 229.4±119.4 MgCha-1 in planted forests (2016, 2014, 2010). The total carbon reserve in the natural forest was 362.3 MgCha-1 and in the planted forestsn(2016, 2014, 2010) it was 233.5 MgCha-1 , 240.2 MgCha-1, 246.4 MgCha-1. Natural and restored forests had similar anoumts of soil carbon, which reinforces the idea that soil is a stabel carbon pool. Morever, restored forests failed to store the same amount of live biomass (an carbon), which supports the idea that it is better to prevent habitat degradation than to restore it.

Increasing of renewable energy share in total energy production is a direction that leads towards European Union’s aims of carbon neutrality by 2050, as well as increases energy self-sufficiency and independence. Some of the main challenges to increase renewable energy share while providing efficient and secure energy supply are related to optimization and profitability of de-centralized energy production systems. Integration of energy storage systems in addition to decentralized renewable energy production, for example, by solar panels, leads to more effective electricity supply and smart energy solutions. The modelling of such complex dynamic system can be performed using system dynamics method. The aim of the article is to forecast the practice of electricity storage in Latvia in the coming decades. A system dynamics model predicting the implementation of battery storage in private households was created for the case study of Latvia. Modelling results reveal that under the right conditions for electricity price, investment costs and with the right policy interventions battery storage technologies combined with PV panels have high potential for utilization in household sector. Model results show that in baseline scenario with no additional policies up 21 422 households or 10.8 % of Latvian households could have combined PV and battery system installed in 2050. Moderate subsidy policy can help to increase this number up to 25 118.