In this review, several cost-effective thin-film coating methods which include dip-coating, spin-coating, spray-coating, blade-coating, and roll-coating are presented. Each method has its set of advantages and disadvantages depending on the type of application. Not all of them are appropriate for large-scale production due to their certain limitations. That is why the coating method should be selected based on the type and size of substrate including the resolution of the required thin-films. The sol-gel method offers several benefits, such as simplicity in fabrication, excellent film uniformity, the capacity to cover surfaces of any size and over vast areas, and a low processing temperature. Nevertheless, these coating methods are somewhat economical and well managed in low-budget laboratories. Moreover, the produced thin-films are homogeneous and have low-surface roughness. Furthermore, some other thin-film deposition methods such as physical vapor deposition (PVD) and chemical vapor deposition (CVD) are also discussed. Since CVD is not restricted to line-of-sight deposition, a characteristic shared by sputtering, evaporation, and other PVD processes, many manufacturing methods favor it. However, these techniques require sophisticated equipment and cleanroom facility. We aim to provide the pros and cons of thin-film coating methods and let the readers decide the suitable technique for their specific application.

Photoluminescent (PL) layers and electroluminescent (EL) systems have been extensively explored for constructing flat panels, screen monitors, and lighting systems. Due to their optical properties, our group is interested in the relationship between optical properties and dielectric constant is converted due to thermal change. In this study, we prepared a zinc sulfide (ZnS) fluorescent film on barium-calcium zirconium titanate ceramics. BCZT0.85 (Ba0.85Ca0.15Zr0.1Ti0.9O3) and BCZT0.9 (Ba0.9Ca0.1Zr0.1Ti0.9O3) were prepared using the solid-state reaction method for the dielectric layer. The BCZT powders were calcined at 1200 and 1250 °C and dwell times of 2 and 4h. The phase formation and microstructure characteristics were then determined using X-ray diffraction and scanning electron microscopy, respectively. The dielectric behavior and optical properties rela-tionship was then studied to determine the composition and optimal conditions for further use as thermal detectors in electric vehicle battery packs. All BCZT powders exhibited the tetragonal phase, which was confirmed by JCPDS No. 01-079-2265. The dielectric constant increased with increasing calcining temperature or dwell time. The dielectric properties showed the BCZT0.85 ceramic sintered had the maximum dielectric constant of 15342 at calcine temperature of 1250 °C for 4h. Therefore, in this study, this condition was optimal for preparing the dielectric film. The maximum dielectric constant film is 42. The electroluminescence intensity of the samples increased in a temperature-dependent manner, with the highest EL intensity at 80 °C. Moreover, the electroluminescence intensity value was enhanced with the increase of the dielectric constant. Our results show promise for developing applications for Opto-thermal sensors.

In this study, we propose a solution process for realizing color glass for building integrated pho-tovoltaic (BIPV) systems by spin coating a color solution composed of a pearlescent pigment mixed in a norland optical adhesive (NOA) matrix. Color solutions are made from mixing pearlescent pigments in NOA63. Compared to a physical vapor deposition process, color coatings are achieved by spin coating in a relatively simple and inexpensive process at room temperature. The optical properties can be easily controlled by adjusting the spin coating speed and the concentra-tion of the pearlescent pigments. The produced color glasses achieved a high transmittance of 85% or more in the visible wavelength range, except the wavelength spectrum exhibiting the maxi-mum reflectance. In addition, we propose a one-step lamination process of color glass on a solar cell by leveraging on the adhesive property of the NOA matrix. This eliminates the cost and pro-cess of additional ethylene vinyl acetate (EVA) layer or other materials used in the conventional lamination process. The color glass produced through this study has stability that does not change its properties over time. Therefore, it is expected to be applied to the BIPV solar module market where aesthetics and energy efficiency are required.

We propose a method of cooling nuclear spin systems of solid-state nanostructures by application of a time-dependent magnetic field synchronized with spin fluctuations. Optical spin noise spectroscopy is considered as the method of fluctuation control. Depending on the mutual orientation of the oscillating magnetic field and the probe light beam, cooling might be either provided by dynamic spin polarization in an external static field or result from population transfer between spin levels without build-up of a net magnetic moment (“true cooling”).

The screen-printed carbon nanofibers electrodes (SPCNFE) represent an alternative with great acceptance due to their results, as well as their low impact for the environment. In order to improve their performance, in the present work they were modified with silver nanoparticles (Ag-NPs) and electrochemically characterized by using anodic stripping voltammetry. From the Ag-NPs synthesis, silver seeds (Ag-NS) and silver nanoprisms (Ag-NPr) were obtained. The Ag-NPs formation was confirmed by micrographs where Ag-NPs with diameters of 12.20±0.04 nm for Ag-NS, and 20.40±0.09 nm for Ag-NPr were observed. The electrodes were modified by using three different deposition methods: drop-casting, spin-coating and in-situ approaches. It was observed that the last methodology showed a low amount of Ag-NS deposited on the electrode surface and a deep alteration of this surface. Those facts suggested that the in situ synthesis methodology were not appropriate for the determination of heavy metals and it was discarded. The incorporation of the nanoparticles by spin-coating and drop-casting strategies showed different spatial distribution on the electrode surface as proved by scanning electron microscopy. The electrodes modified by these strategies, were evaluated for the cadmium(II) and lead(II) detection using differential pulse anodic stripping voltammetry, obtaining detection limit values of 2.1 and 2.8 µg L^-1, respectively. The overall results showed that the incorporation route does not change directly the electrocatalytic effect of the nanoparticles, but the shape of these nanoparticles (spherical for seeds and triangular for prisms) has a preferential electrocatalytical enhancement over Cd(II) or Pb(II).

Magneto-electrochemistry (MEC) is a unique paradigm in science, where electrochemical experiments are carried out as a function of an applied magnetic field, creating a new horizon of potential scientific and technological applications. Over the time, detailed understanding of this research domain was developed to identify and rationalize the possible effects exerted by a magnetic field on the various microscopic processes occurring in an electrochemical system, such as: electrolyte properties governed by charge-transfer process (electric conductivity, viscosity, and diffusivity), mass transfer, electrochemical kinetics and on the structure/quality of products formed either at the working electrode or in the electrochemical cell. Particularly, magnetic field controlled chiral architecture obtained from deposited metal, alloys and catalyst and their excellent enantio-recognition in experimental frame is highly appealing. Interestingly, Hall effect was also demonstrated in electrolytic medium via an impressive experimental technique which is being employed for further theoretical understanding in the field of magneto-electrochemical science. Later, a highly reproducible local temperature variation was observed in electrochemical electrolytes exposed to perpendicular magnetic and electric fields. However, until recent studies, none of the above mentioned reports considered the possibility of a spin-dependent related charge-transfer process. Recent experimental and theoretical studies reveal that electron’s transmission through chiral molecules is spin-selective and this effect has been referred to as chiral-induced spin-selectivity (CISS) effect. The CISS effect pave the way for the building up of a system characterized by a net magnetic moment exploiting the spin-filtering ability of chiral molecules. This interplay between chirality and magnetism may shed light on fundamental scientific aspects underlying the enantio-recognition and highly efficient electron-transfer that occurs in biological process.

Using the unique combination of atomically resolved atom probe tomography (APT) and volume averaged neutron (resonance) spin echo (NRSE and NSE) experiments, the influence of nano-scaled clusters on the spin relaxation in spin glasses was studied. For this purpose, the phase transition from the paramagnetic phase to the spin glass phase in a Fe-Cr spin glass with a composition of Fe_17.8Cr_82.2 was studied in detail by means of NRSE. The microstructure was characterised by APT measurements, which show local concentration fluctuations of Fe and Cr on a length scale of 2 to 5 nm, which lead i) to the coexistence of ferro- and anti-ferromagnetic clusters and ii) a change of the magnetic properties of the whole sample, even in the spin glass phase, where spins are supposed to be randomly frozen. We show that a generalized spin glass relaxation function, which was successfully used to describe the phase transition in diluted spin glasses, can also be used for fitting the spin dynamics in spin glasses with significant concentration fluctuations.

The kinetic analysis of octogen coating with a polyurethane base containing hydroxyl-terminated polybutadi-ene (HTPB) was investigated using infrared spectroscopy. The coating process involved a solvent method, where octogen and liquid polyurethane were mixed, the solvent was evaporated, and curing took place at an elevated temperature. The ratio of HTPB to diisocyanate was equimolar. Initially, the curing process occurred in the solvent system, followed by further curing in the bulk system. The kinetic analysis was performed using a modified diffusion-autocatalytic model, which includes non-catalytic, autocatalytic, and diffusion compo-nents. This model was compared with others during the bulk reaction and proved to be effective in correcting errors, particularly in the gel time region. Thermodynamic parameters were evaluated using the Arrhenius and Eyring equations. The reaction rate was initially controlled by chemical reactivity, but after the gel time, diffusion became the controlling factor. In the HTPB-TDI system, both the non-catalytic and autocatalytic parts decreased with increasing temperature, while diffusivity increased. It is worth noting that diffusivity is temperature-dependent. Different diisocyanates, namely toluene diisocyanate (TDI), isophorone diisocyanate (IPDI), and hexamethylene diisocyanate (HMDI), were studied, revealing that HMDI exhibited higher reactivi-ty than TDI and IPDI. The catalyst effect on reaction rate HTPB-TDI system is investigated. Catalysts adding (0.1%) to HTPB-TDI system is really decrease their activation energy by efectivity DBTL>FeAA>TPB. Catalyst not change their diffusivity.

In this study, a novel binary nanocomposite system based on TiO₂-SiO₂ was functionalized with trimethylolpropane triacrylate (TMPTA) and characterized by XPS and XRD. Results revealed that TiO₂-SiO₂ nanoparticles were covalently functionalized. Functionalized nanoparticles at low concentrations (0.1 wt% and 0.5 wt%) were dispersed in acrylic acid acting as a polymer matrix. Nanocomposite coatings analysis demonstrate to achieve superhydrophilic properties as well as very good optical characteristics. Water contact angle characterization showed the functionalization effect by achieving a superhydrophilic behavior with a contact angle less than 5°. UV-Vis measurements demonstrated high optical transmittance above 95% for the coatings. Based on the obtained results a mechanism describing the chemical interactions of the constituents responsible for the synergy in the nanocomposite as well as the morphological play role in the behavior are presented.

Intercalation of noble metals can produce giant Rashba-type spin-orbit splittings in graphene. The spin-orbit splitting more than 100 meV has not yet been achieved in graphene on a metallic or a semiconductor substrate. Here, we report the p-type graphene obtained by Pt intercalation of zero-layer graphene on SiC substrate. The spin splitting of ∼200 meV was observed at a wide range of binding energies. Comparing the results of theoretical studies of different models with the experimantal ones measured by spin-ARPES, XPS and STM methods, we came to the conclusion that inducing giant spin-orbit splitting requires not only a fairly close arrangement of graphene to Pt layer, but also the presence of graphene corrugation caused by non-flat Pt layer. This makes it possible to find a compromise between strong hybridization and increased spin-orbit interaction. In our case, this is achieved by forming Pt submonolayer ordered on a nanometer scale under graphene.

We present an experimental study of the coherence properties of a single heavy-hole spin qubit formed in one quantum dot of a gated GaAs/AlGaAs double quantum dot device. We use a modified spin-readout latching technique in which the second quantum dot serves both as an auxiliary element for fast spin-dependent readout within a 200ns time window and also as a register for storing the spin-state information. To manipulate the single-spin qubit we apply sequences of microwave bursts of various amplitudes and durations to make Rabi, Ramsey, Hahn-echo, and CPMG measurements. As a result of the qubit manipulation protocols combined with the latching spin readout, we determine and discuss the achieved qubit coherence times: T1, T_Rabi, T2*, and T_CPMG vs microwave excitation amplitude, detuning and additional relevant parameters

The electron of magnetic spin −1/2 is a Dirac fermion of a complex four-component spinor field. Though it is effectively addressed by relativistic quantum field theory, an intuitive form of the fermion still remains lacking. In this novel undertaking, the fermion is examined within the boundary posed by a recently proposed MP model of a hydrogen atom into 4D space-time. Such unorthodox process conceptually transforms the electron to the four-component spinor of non-abelian in both Euclidean and Minkowski space-times. Supplemented by several postulates, the relativistic and non-relativistic applications of the model are explored from an alternative perspective. The outcomes have important implications towards defining the spin-orbit coupling of particles from external light interactions. These findings, if considered could consolidate properly the fundamentals of the quantum state of matter from an alternative perspective using quantum field theory application and they warrant further investigations.

The quasi-two-dimensional organic charge-transfer salt κ-(BEDT-TTF)₂Cu₂(CN)₃ is one of the prime candidates for a quantum spin-liquid due the strong spin frustration of its anisotropic triangular lattice in combination with its proximity to the Mott transition. Despite intensive investigations of the material's low-temperature properties, several important questions remain to be answered. Particularly puzzling are the 6 K anomaly and the enigmatic effects observed in magnetic fields. Here we report on low-temperature measurements of lattice effects which were shown to be particularly strongly pronounced in this material (R. S. Manna et al., Phys. Rev. Lett. 104, 016403 (2010)). A special focus of our study lies on sample-to-sample variations of these effects and their implications on the interpretation of experimental data. By investigating overall nine single crystals from two different batches, we can state that there are considerable differences in the size of the second-order phase transition anomaly around 6 K, varying within a factor of 3. In addition, we find field-induced anomalies giving rise to pronounced features in the sample length for two out of these nine crystals for temperatures T < 9 K. We tentatively assign the latter effects to B-induced magnetic clusters suspected to nucleate around crystal imperfections. These B-induced effects are absent for the crystals where the 6 K anomaly is most strongly pronounced. The large lattice effects observed at 6 K are consistent with proposed pairing instabilities of fermionic excitations breaking the lattice symmetry. The strong sample-to-sample variation in the size of the phase transition anomaly suggests that the conversion of the fermions to bosons at the instability is only partial and to some extent influenced by not yet identified sample-specific parameters.

Positively charged polyelectrolytes hold significant potential as materials for creating antibacterial coatings. Water-soluble macromolecules can be easily deposited onto a treated surface through various techniques, forming a film that provides antimicrobial properties to the surface through electrostatic interactions with bacterial membranes. The structural and molecular weight characteristics of the polymers play a crucial role in the physical and mechanical properties of the coatings. In this study, we investigated the properties of branched polyethyleneimine (PEI) and linear polydiallyldimethylammonium chloride (PDADMAC) coatings with different molecular weights of polymer samples to determine their suitability as stable coatings with antibacterial properties against foodborne bacteria. Using thermogravimetric analysis, dynamometry, and dynamic light scattering, we examined the physicochemical and mechanical properties of the macromolecules in water solutions and in coatings. Microbiological study was conducted to analyze the biocidal activity of the polycations in solutions and on the surface of coatings. Our findings showed that the moisture saturation of the polycationic coatings did not significantly depend on the chemical nature of charged groups or the molecular weight or architecture of macromolecules. Moreover, biocidal activity was not found to depend on the molecular weights of PEI and PDADMAC. However, the lowering of the molecular weight of polymers resulted in the loss of cohesive forces in the coatings and to dramatically loss of the stability towards wash-off with water. The diffusion coefficient (D0) of macromolecules was identified as a key parameter for the wash-off mechanism. Films formed by molecules with D0 below 1×10-7 cm2/s demonstrated high resistance to wash-off procedures. We demonstrated that PEI and PDADMAC samples with high molecular weights showed high antimicrobial activity towards L. monocytogenes. Our results highlight the importance of macromolecule characteristics in the development of new biocidal coatings based on polycations.

State transition in the multiple-levels system has the great potential applications in the quantum technology. In this article we employ a deterministic approach in complex space to analyze the dynamics of the 1s-2p electron transition in the hydrogen atom. The electron’s spin motion is embodied in the framework of quantum Hamilton mechanics that allows us to examine the transition dynamics more precisely. The transition is driven by an oscillating electric field in the z-direction. The electron’s transition process can be visualized by monitoring its motion in the complex space. The quantum potential and the total energy proposed in this paper provide new indices to observe the dynamic changes of electrons in the transition process.

This review provides a systematic analysis of the literature data on the electrodeposition of composite coatings using plating baths based on a new generation of room-temperature ionic liquids, known as deep eutectic solvents (DESs). Such systems offer several advantages over traditionally used aqueous electrolytes and organic solvent-based electrolytes. The colloidal-chemical properties of suspension and colloidal electrolytes for composite deposition are thoroughly examined. New theories describing the kinetics of co-deposition of composite layers are characterized. The kinetics and mechanism of electrochemical deposition processes of composite coatings with metallic matrices are discussed. Case studies regarding the electrodeposition of composite coatings based on electrodeposited copper, silver, zinc, tin, nickel, cobalt, and chromium from DES-assisted electroplating baths are described and systematized. The main prospective directions for further research in the discussed scientific area are highlighted.

Guava is a vital fruit worldwide, especially in Pakistan, and due to its nutritional value famous in each age group. Due to a very short shelf life, the marketing and export of this fruit faced severe constraints. Therefore, in the current study, edible coating of chitosan (0, 0.5, 1.0, 1.5, and 2.0%) was evaluated on postharvest shelf life when guava fruits were stored (room temperature and 4 °C temperatures) for 12 days. The chitosan treated coating fruits have shown reduced total sugars and malondialdehyde levels compared to untreated control samples. However, a significant difference (p ≤ 0.05) in total sugar and malondialdehyde levels exists between samples stored in m compared to refrigerated temperature (4 °C). The chitosan-coated samples have shown a greater amount of vitamin C, quercetin, rutin, and total phenolic contents than control samples. However, these nutritional parameters' levels were significantly different (p ≤ 0.05) in samples stored at room than samples stored at refrigerated temperature. However, the levels of crude fiber, potassium, and sodium were found statistically nonsignificant (p ≥0.05) in control versus chitosan treated coating treatments. The findings have documented that the coatings of 1.5 and 2.0% were most effective for extension in shelf life and maintaining the nutritional attributes of guava fruit.

First, we examine how spin is treated in special relativity and the necessity of introducing spin supplementary conditions (SSC) and how they are related to the choice of a center-of-mass of a spinning particle. Next, we discuss quantum electrodynamics and the Foldy-Wouthuysen transformation which we note is a position operator identical to the Pryce-Newton-Wigner position operator. The classical version of the operators are shown to be essential for the treatment of classical relativistic particles in general relativity, of special interest being the case of binary systems (black holes/neutron stars) which emit gravitational radiation.

A structure-based view on mesons is given, based upon the concept of an archetype quark, described as a pointlike source producing an energy flux, the spatial description of which is derived from Dirac’s second dipole moment. This enables to conceive the archetype meson (pion) as a structure that behaves as a one-body anharmonic quantum mechanical oscillator. All mesons appear being excitations of the archetype, thereby allowing a calculation of the mass spectrum without the use of empirical parameters for the masses of the quark flavors. This includes a physically comprehensible analysis of the spin-spin interaction between quarks. It also provides a solution for the eta-etaprime puzzle. Next to this, it is shown that quite some particles that are presently regarded as elementary, have a common root and can be traced back to a few archetypes only.

In particle physics, spin is an intrinsic form of angular momentum carried by the elementary particles. It is believed that spin is a solely quantum-mechanical phenomenon, which does not have a counterpart in classical mechanics. We have derived the simplest equations of spin and magnetic moment of a charged elementary particle. These formulas enable us to understand the physical nature of the spin and the structure of elementary particles. It is shown that the electron and muon are in the shape of a thin ring with a circular cross section (torus), and the proton is in the form of a ring with a non-circular cross section (toroid). The connection between the photon’s spin of and the propagation of electromagnetic waves is considered.

In the present work, three different atmospheric plasma sprayed (APS) alumina coatings were fabricated using three fused and crushed alumina powders of different particle size fine, medium and coarse. The influence of the particle size on thermal properties and micro-structural features of the produced coating were investigated by thermal insulation test and detailed image analysis technique, respectively. The analyzed micro-structural features include the total porosity, pore size (fine, medium, and large) and cracks. All types of cracks were considered in calculations as voids and were evaluated according to their sizes as pores. All spray parameters except the particle size were fixed throughout the spraying process. The results revealed that the fine starting powder has produced the densest coating with the lowest total porosity and that the total porosity increases with an increasing particle size. This was expected as powders of smaller particle size will reach a higher in-flight temperature and velocity than powders of bigger particle sizes as long as the same spray parameters are applied. However, a detailed image analysis investigation on the three produced coatings showed that the fraction of fine pores and cracks versus the total porosity is substantially higher in coatings produced by using fine starting powders than those produced using medium and coarse powders. In this work, a connection between the thermal insulation and the porosity fraction, which includes fine pores and cracks, was revealed.

In this review, we trace the evolution of the quantum spin-wave theory treating non-collinear spin configurations. Non-collinear spin configurations are consequences of the frustration created by competing interactions. They include simple chiral magnets due to competing nearest-neighbor (NN) and next-NN interactions and systems with geometry frustration such as the triangular antiferromagnet and the Kagomé lattice. We review here spin-wave results of such systems and also systems with the Dzyaloshinskii-Moriya interaction. Accent is put on these non-collinear ground states which have to be calculated before applying any spin-wave theory to determine the spectrum of the elementary excitations from the ground states. We mostly show results from a self-consistent Green’function theory to calculate the spin-wave spectrum and the layer magnetizations at finite T in two and three dimensions as well as in thin films with surface effects. Some new unpublished results are also included. Analytical details and the validity of the method are shown and discussed.

Several coatings configurations of combined aluminizing and diffusion layered aluminide on 316 steel were produced and characterized. These coatings, typically employed as thermal barrier coating (TBC), can also be effective as vibration reduction elements at intermediate and high temperatures. This preliminary work has been focused on the microstructural design and processing effects of the coatings. The damping of the produced specimens was measured up to 450°C and compared with that of the steel substrate. The most performing coatings contain an Al-Si layer and exhibit a steep damping increase above 200 °C, reasonably due to dislocation movements by plastic straining of soft alloy layer and to the interface sliding between layers with different elastic moduli.

Abstract: An Al-Co-Y diffusion coating was prepared on a TiAl alloy by pack cementation process at a low temperature range of 650-720 ℃. The influence of different activators and co-deposition temperatures on the coating’s microstructure and formation process, and high temperature oxida-tion performance was studied. The results showed that NaF was a more suitable activator for preparing the Al-Co-Y diffusion coating on TiAl alloy compared to NH4Cl and AlCl3. A more compact coating structure can be obtained when deposition was performed at 680 ℃ using NaF as the activator. The coating was mainly composed of a TiAl3 outer layer, a TiAl2 inner layer, and a thin Al-rich TiAl inter-diffusion layer. The growth of the coating exhibited a positive linear correlation between coating thickness increase and the square root of deposition time. The high-temperature oxidation tests showed that a dense scale mainly composed of Al2O3 and a small amount of TiO2 formed on the coating after oxidation at 950 ℃ for 100 h. The scale possessed excellent high-temperature oxidation resistance, with a parabolic rate constant of the oxidation weight gain approximately 4.9×10-3 mg2/cm4 h, which is lower than that of the TiAl substrate by about three orders of magnitude, and lower than that of the pure Al diffusion coating more than one order of magnitude.

Slot-die coatings are advantageous when used for coating large-area flexible devices; in particular, the coating width can be controlled, and simultaneous multi-layer coatings can be processed. Till date, the effects of ink widening and coating gap on the coating thickness have only been considered in a few studies. To this end, we developed two mathematical models to accurately estimate the coating width and thickness considering these two effects. We used root mean square deviation (RMSD) to experimentally verify the developed method. The coating width was seen to increase and the coating thickness was seen to decrease when the coating gap was increased. Experimental results showed that the estimation performances of the coating width and thickness models were as high as 98.46 % and 95.8 %, respectively. We believe that the developed models can be useful for determining the coating conditions according to the ink properties to coat a functional layer with user-defined widths and thicknesses in both lab- and industrial-scale roll-to-roll slot-die coating processes.

In previous papers we have shown how Schrödinger’s equation which includes an electromagnetic field interaction can be deduced from a fluid dynamical Lagrangian of a charged potential flow that interacts with an electromagnetic field. The quantum behaviour was derived from Fisher information terms which were added to the classical Lagrangian. It was thus shown that a quantum mechanical system is driven by information and not only electromagnetic fields. This program was applied also to Pauli’s equations by removing the restriction of potential flow and using the Clebsch formalism. Although the analysis was quite successful there were still terms that did not admit interpretation, some of them can be easily traced to the relativistic Dirac theory. Here we repeat the analysis for a relativistic flow, pointing to a new approach for deriving relativistic quantum mechanics.

Electrons moving at slow speeds much lower that the speed of light are described by a wave function which is a solution of Pauli’s equation. This is a low velocity limit of the relativistic Dirac equation. Here we compare two approaches, one which is the more conservative Copenhagen’s interpretation denying a trajectory of the electron but allowing a trajectory to the electron expectation value through Ehrenfest theorem. The said expectation value is of course calculated using a solution of Pauli’s equation. A less orthodox approach is championed by Bohm, and attributes a velocity field to the electron also derived from the Pauli wave function. It is thus interesting to compare the trajectory followed by the electron according to Bohm and its expectation value according to Ehrenfest. Both similarities and differences will be considered.

Spin crossover (SCO) complexes are in the forefront of image, memory and sensing devices, with applications already established since for thirty years. In order to reach magnetic multistability conditions, the high-spin (HS) and low-spin (LS) states have to be carefully balanced by ligand field stabilization and spin pairing energies. Both of these effects could be effectively modelled by electronic structure theory, if the description would be accurate enough to describe these concurrent influences to within a few kJ/mol. Such a milestone would allow for the in silico-driven development of SCO complexes. However, so far, the ab initio simulation of such systems has been dominated by general gradient approximation density functional calculations. The latter can only provide the right answer for the wrong reasons, given that the LS states are grossly stabilized. In this contribution, we explore different venues for the parameterisation of hybrid functionals. A fitting set is provided on the basis of explicitly correlated coupled cluster calculations, with single- and multi-dimensional fitting approaches being tested to selected classes of hybrid functionals (hybrid, range separated and local hybrid). Promising agreement to benchmark data is found for a rescaled PBE0 hybrid functional and a local version thereof, with a discussion of different atomic exchange factors.

We investigate on the plasmons of monolayer MoS₂ in the presence of spin-orbit interactions (SOIs) under the random phase approximation. The theoretical study shows that two new and novel plasmonic modes can be achieved via inter spin sub-band transitions around the Fermi level duo to the SOIs. The plasmon modes are optic-like, which are very different from the plasmon modes reported recently in monolayer MoS₂, and the other two-dimensional systems. The frequency of such plasmons increases with the increasing of the electron density or the spin polarizability, and decreases with the increasing of the wave vectors q. Our results exhibit some interesting features which can be utilized to the plasmonic and terahertz devices based on monolayer MoS₂.

K-Rb-83Kr based atomic co-magnetometer for measuring moving MEGs is theoretically studied in this paper. Parameters such as the spin exchange rates, the spin dephasing rates and the polarization of the nuclear spins are studied to configure the co-magnetometer. Results show that the nuclear spin could generate around 700 nT magnetic field under which the nuclear spin could compensate wide range of magnetic fields. We also showed the hybrid optical pumping vapor cell fabrication process in this paper. Alkali metals were mixed in a glove box and then was connected to the alkali vapor cell fabrication system. The vapor cell fabrication process is illustrated in this paper.

In this study, the efficiency of coating (alginate and carrageenan) and osmotic dehydration pre-treatment (NaCl and sucrose) on decreasing oil uptake of potato strips was assessed. It was examined how various pre-treatments affected the sample’s texture, morphology, color and density properties as well as their moisture content and effective moisture diffusion coefficient (Deff). Results showed that NaCl osmotic dehydration pre-treatment and sucrose solution decreased oil uptake by 30.76% and 41.75%. This is attributed to moisture removal increasing caused by improving dielectric properties. Osmotic dehydration and coating pre-treatment frequently enhanced product shrinkage, browning index, a* and ∆E. Conversely, density, lightness, breaking force, Deff and b* decreased. In control samples, SEM revealed a severely damaged internal structure in comparison to a tissue homogenous layer produced by coating. For moisture loss and oil uptake, the coefficient of determination (R2) and root mean square error (RMSE) of eight empirical models were compared. Finally, the Dehghannya and Krokida model (moisture loss) and the Movahhed and Naghavi model (oil uptake) were found the best fit to the experimental data. Although coating pre-treatment and osmotic dehydration can be used as an alternate de-oiling approach for potato chips, the mechanism of oil uptake reduction differ.

The powdered sorbents were applied in a batch system under "static" conditions and showed a much higher adsorption capacity than the granular one. These type of sorbents are more suitable for small quantities of water with a high concentration of arsenic. The possibilities of using all the tested methods for arsenic removal have been evaluated, and a scheme of the technological process has been proposed.

The surface plasmon resonance of gold nanoparticles causes visible light absorption and scattering effects that may be used in optical coatings for eliminating blue light emission from display monitors, blocking UV light and for decorative applications. This study examines the achievement of functional properties provided by gold nanoparticles in a commercially established C60 fullerene-coated eyewear product. The gold nanoparticles used were sourced from recycling rapid lateral flow tests (LFIA), which use gold nanoparticles as test markers. After the gold`s recovery Ultrasonic Spray Pyrolysis (USP) with freeze-drying was used for the synthesis of new gold nanoparticles, to be used in optical coatings. The gold nanoparticles were examined with SEM, TEM, DLS, zeta potential, BET, and Vis-NIR for characterising their shapes and sizes, required for determination of the surface plasmon resonance effect. After applying the newly produced gold nanoparticles with fullerene C60 in a combined coating for eyewear lenses, the absorption and transmission of the lenses was determined for establishing changes in the coating functionality. The results show that enhancing the fullerene C60 coating with gold nanoparticles improves light absorption and reflectance for blue and UV light further, which may be evaluated as beneficial for the eyewear user, as the reduction of eye strain is improved due to the coating.

Renewable nanocellulose materials received increased attention owing to their small dimensions, high specific surface area, high mechanical characteristics, biocompatibility, and compostability. Nanocellulose coatings are among many interesting applications of these materials to functionalize different by composition and structure surfaces, including plastics, polymer coatings, and textiles with broader applications from food packaging to smart textiles. Variations in porosity and thickness of nanocellulose coatings are used to adjust a load of functional molecules and particles into the coatings, their permeability, and filtration properties. Mechanical stability of nanocellulose coatings in a wet and dry state are critical characteristics for many applications. In this work, nanofibrillated and nanocrystalline cellulose coatings deposited on the surface of polymer films and textiles made of cellulose, polyester, and nylon are studied using atomic force microscopy, ellipsometry, and T-peel adhesion tests. Methods to improve coatings adhesion and stability using physical and chemical cross-linking with added polymers and polycarboxylic acids are analyzed in this study. The paper reports on the effect of the substrate structure and ability of nanocellulose particles to intercalate into the substrate on the coating adhesion.

We demonstrated a new approach to the production of three-dimensional-coated patterns using liquid route. Metallic perovskite oxides were coated onto three-dimensional (3D) microstructured substrates with different aspect ratios. The success of the method relies on the solution viscosity monitored by adding viscous liquid. The process of oxide thin films consists in three steps: preparing the precursor solution, coating the solution by spin-coating process onto three-dimensional-Si substrates and post-annealing. The chemical solution 3D-coating is conformal.

In this article, we show theoretically and experimentally the formation of spin-waves band gaps in a magnonic crystal that was implemented by the deposition of periodic micro-structured strips of magnetite nanoparticles. A theoretical model describing the spectra of the transmitted spin-waves bandgaps is proposed. This is achieved using a simple model based on microwave transmission line theory and considering the presence of micro-structured strips of magnetite nanoparticles on the surface. Such magnonic crystal of equally spaced micro-structured strips of magnetite nanoparticles on the surface of an yttrium iron garnet thin film has been implemented and measured. The periodic micro-structured nanoparticles are deposited on the surface of such yttrium iron garnet single-crystal film grown on a gallium-gadolinium garnet substrate via dip-coating technique. Propagation of magnetostatic surface spin-waves is studied and it is shown that the presence of such periodic structure leads to the formation of spin-wave band gaps in the transmission characteristics. The spin-wave detection has been carried out using a pair of microwave antennas and a vector network analyzer. The results show that the periodic structure formed by the magnetite strips modifies the spectra of the transmitted spin waves producing band gaps.

Biocidal coatings are of great interest to the healthcare system. In this work, the biocidal activity of coatings based on a complex biocide containing polymer and inorganic active antibacterial c omponents was studied. Silver oxide was distributed in a matrix of a positively charged interpolyelectrolyte complex (IPEC) of polydiallyldimethylammonium chloride (PDADMAC) and sodium polystyrene sulfonate (PSS) using ultrasonic dispersion, forming nanoparticles with an average size of 5-6 nm. The formed nanoparticles in the matrix are not subject to agglomeration and changes in morphology during storage. It was found that the inclusion of silver oxide in a positively charged IPEC allows a 4-fold increase in the effectiveness of the complex biocide against E. coli K12 in comparison with the biocidal effect of PDADMAC and IPEC. Polycation, IPEC and the IPEC/Ag2O ternary complex form coatings on the glass surface due to electrostatic adsorption. Adhesive and cohesive forces in the resulting coatings were studied on micron-scale coatings using dynamometry. It was found that the stability of the coating is determined primarily by adhesive interactions. At the macro level, it is not possible to reliably identify the role of IPEC formation on adhesion. On the other hand, the use of the optical tweezers method makes it possible to analyze macromolecules in submicron scale and to evaluate the multiple increase in adhesive forces when forming a coating from IPEC compared to coatings from PDADMAC. Thus, the application of ternary IPEC/Ag2O complexes makes it possible to obtain coatings with increased antibacterial action and improved adhesive characteristics.

According to research, we have learned that Mg and TiO2 are new types material of marine protective coatings. We found that the addition of Mg can improve the performance of Zn-Al coating passivation film, and TiO2 has excellent photocatalytic self-cleaning performance. In this paper Zn-Al pseudo alloy coating was prepared by cold spray technique, and Zn-Al-Mg-TiO2 pseudo alloy composite coating was prepared by adding Mg and nano-TiO2. The effects of Mg and TiO2 to the marine protective properties of Zn-Al coatings were studied by friction and wear test, dynamic salt water corrosion test, electrochemical test, scanning electron microscope(SEM), energy dispersive spectrometer(EDS) and super deep scene 3D microscope. The results show that the addition of Mg and nano-TiO2 not only fills the gap of the coating and improves the density of the coating, but also generates grid-like flocculent corrosion products on the surface of the coating which can gather other corrosion products to improve the density of corrosion products, reduce the friction coefficient and corrosion rate of the coating surface, effectively prevent the invasion of Cl- in solution, and improve the wear and corrosion resistance of the coating.

This paper presents a new method of preparing a coating on the Ti65 titanium alloy by a two-step procedure comprising hot-dipped aluminum and solid carburization. The effects of the carburization in the presence of NaCl deposit at 810oC have been systematically studied. In this article, the microstructure, morphology, phase composition of the coating, and the corrosion products were investigated by SEM, EDS, and X-ray diffraction. Results indicated that the corrosion resistance of hot dip aluminum/carburizing composite coating was not significantly enhanced by hot dip aluminum coating. This can be attributed to the formation of TiC and Ti3AlC after carburization, which promoted the formation of loose and unprotected TiO2 in the coating during molten salt corrosion. In addition, the oxidation of the carbon atom into CO2 /CO leaded to a high concentration of vacancy in the coating, creating channels for NaCl to penetrate the coating and accelerated the corrosion rate.

In roll-to-roll (R2R) processing, uniformity of the web is a crucial factor that can guarantee high coating quality. To understand web defects due to thermal deformation, we analyzed the effects of web unevenness on the coating quality of an yttria-stabilized zirconia (YSZ) layer, a brittle electrolyte of solid oxide fuel cells (SOFCs). We used finite element analysis to analyze the thermal and mechanical deformations at different drying temperatures. A YSZ layer was also coated using R2R slot-die coating to observe effects of web unevenness on the coating quality. It was seen that web unevenness was generated by thermal deformation due the conduction and convection heat from the dryer. Owing to varying web unevenness with time, the YSZ layer developed cracks. At higher drying temperatures, more coating defects having larger widths were generated. Results indicated that web unevenness at the coating section led to coating defects, which could damage the SOFC and decrease its yield in the R2R process. From this study, we suggest that coating defects, generated by the web unevenness owing to the convection and conduction heat, should be considered for the high-volume production of brittle electrolytes using the R2R process.

In this work, a generalized analogue to the Pauli spin matrices is presented and investigated. The proposed Hermitian spin matrices exhibit a general symmetry. The generalized spin projection operators are derived and the electrodynamics for hypothetical fermions are explored using the proposed spin matrices. The fermionic quantum Heisenberg model is constructed using the proposed spin matrices and comparative studies against simulation results using the Pauli spin matrices are conducted. Further analysis on key findings as well as discussions on extending the proposed spin matrix framework to describe hypothetical bosonic systems (spin-1) are provided.

Coating of organic molecules from the solution phase can result in directional crystal growth under certain conditions, even on a smooth isotropic surface and without the need of any kind of graphoexpitaxial preparation of the substrate. Based on reviewing the results from a variety of coating techniques and conditions, we identify the condition that the coating speed should equal the growth speed of the fastest growing crystal plane as crucial for achieving a high degree of directional crystallization.

Deformation behavior of the composite "hen's eggshell - polymer plomb" under bending is examined. Polymer coating does not change the type of behavior of the composite based on eggshell that continues to be brittle despite the mechanical characteristics of the composite could vary in wide limits for brittle structure. Joining "hen's eggshell – polymer plomb" never crack under loading and, hence, it exhibits the high cohesion strength under stresses applied in these experiments. It seems that the composite "hen's eggshell - polymer plomb" could apply as the substitution of the composite "tooth enamel - polymer plomb" under elaboration of novel restorative materials for dentistry, namely, for estimation of their mechanical properties including cohesive strength.

This study reports on the development of bio-based hydrophobic coatings for packaging papers through deposition of polyhydroxybutyrate (PHB) particles in combination with nanofibrillated cellulose (NFC) and plant wax. In a first approach, PHB particles in micrometer range (PHB-MP) were prepared through a phase-separation technique providing internally nanosized structures. The particles were transferred as a coating by dip-coating filter papers in the particle suspension, followed by sizing with a carnauba wax solution. This approach allowed partial to almost full surface coverage of PHB-MP over the paper surface resulting in static water contact angles of 105° to 122° and 129° to 144° after additional wax coating. In a second approach, PHB particles with submicron sizes (PHB-SP) were synthesized by an oil-in-emulsion (o/w) solvent evaporation method, and mixed in aqueous suspensions with 0 to 7 wt% NFC. After dip-coating filter papers in PHB-SP/NFC suspensions and sizing with a carnauba wax solution, static water contact angles of 112° to 152° were obtained. The intrinsic properties of the particles were analyzed by scanning electron microscopy, thermal analysis and infrared spectroscopy, indicating higher crystallinity for PHB-SP than PHB-MP. The chemical interactions between the more amorphous PHB-MP particles and paper fibers were identified as an esterification reaction, while the morphology of the NFC fibrillar network was playing a key role as binding agent in the retention of more crystalline PHB-SP at the paper surface, hence contributing to higher hydrophobicity.

In this study, the problem of overcoming the infinite energy barrier separating the bradyonic and tachyonic realms is investigated. Making use of the Majorana equation for particles with arbitrary spin and the Heisenberg uncertainty principle, it is proved that, under certain conditions of spatial confinement, quantum fluctuations allow particles with very small mass and velocity close to the speed of light to pass in the tachyonic realm, avoiding the problem of the infinite barrier (bradyon–tachyon tunnelling). This theoretical approach allows an avoidance of the difficulties encountered in quantum field theory when it is extended to particles with imaginary rest mass.

Bioactive surface coatings have retained the attention of researchers and physicians due to their versatility and range of applications in orthopedics, particularly in infection prevention. Antibacterial metal nanoparticles (mNPs) are a promising therapeutic, with vast application opportunities on orthopedic implants. The current research aimed to construct a polyelectrolyte multilayer on a highly porous titanium implant using alternating thin film coatings of chitosan and alginate via the layer-by-layer (LbL) self-assembly technique, along with the incorporation of silver nanoparticles (AgNPs) or titanium dioxide nanoparticles (TiO2NPs), for antibacterial and osteoconductive activity. These mNPs were characterized for their physicochemical properties using quartz crystal microgravimetry with dissipation system, nanoparticle tracking analysis, scanning electron microscopy, and atomic force microscopy. Their cytotoxicity and osteogenic differentiation capabilities were assessed by AlamarBlue and alkaline phosphatase (ALP) activity assays, respectively. The antibiofilm efficacy of the mNPs tested against Staphylococcus aureus. The LbL polyelectrolyte coating was successfully applied to the porous titanium substrate. A dose-dependent relationship between nanoparticle concentration and ALP as well as antibacterial effects was observed. TiO2NP samples were also less cytotoxic than AgNP counterparts, although similarly antimicrobial. Together, these data serve as a proof-of-concept for a novel coating approach for orthopedic implants with antimicrobial and osteoconductive properties.

A detailed review of the scientific literature was undertaken to examine the most recent developments in plasma processing in the field of medicine. The first part of the review includes a detailed breakdown of the different types of coatings that can be applied onto medical devices using plasma, with a specific focus on antimicrobial surfaces. The developments during 2023 in plasma deposited biocompatible, drug delivery and adhesive coatings are described and specific applications in additive manufacturing are highlighted. The use of plasma and plasma activated liquids as standalone therapeutics continues to evolve and pertinent advances in this field are described. In addition, the combination of plasma medicine with conventional pharmaceutical interventions was reviewed and key emerging trends were highlighted, including the use of plasma to enhance drug delivery directly into tissue. The potential synergies between plasma medicine and chemotherapeutics for oncology and infection treatment is a growing area and recent advancements are noted. Finally, the use of plasma to control excess antibiotics and to intentionally degrade such materials in waste streams is described.

We present an investigation on the fracture of a mold, comparing it with a normal part using specific techniques, such as EDX, SEM, and AES. The EDX analysis revealed that the composition of the normal part was consistent with that of low carbon steel, mainly comprising Fe and C. In contrast, the fractured part exhibited cracks due to nonconforming nonmetallic inclusions and reticular carbides, with fractures resulting from microporosity agglomeration and cleavage fracture. The SEM and AES analyses further presented the causes of mold fracture, highlighting the mechanism by which dimples on the specimen edge contributed to the fracture. The EDX analysis confirmed that the mold experienced thermal brittleness during use. To enhance mold durability and extend its lifespan, a double-pulse electrodeposition method was employed to create a NiCo alloy coating as a replacement for the Cr layer on the metal surface. The coating exhibited a smooth and scratch-free surface. The prepared NiCo special coating significantly increased the mold yield strength by approximately 313.8%, facilitated a 13% increase in plastic deformation, and reduced fracture strain by 25%, effectively preventing mold fracture and 3improving its service life.

The cape gooseberry (Physalis peruviana L.) is an exotic tropical fruit of great national and international importance due to its nutritional, and organoleptic properties. The objective of this study was to evaluate different postharvest treatments: Coating, Vacuum Impregnation, and Immersion, on the conservation of some quality characteristics of cape gooseberry fruit. Moreover, different conditions of the selected treatment were studied. The weight loss was assessed with gravimetric analysis for fresh and treated fruits. Firmness was determined by instrumental texture. The sensory analysis was conducted using a multidimensional profile approach. Of the treatments evaluated, the lowest weight loss was recorded with the use of coating and immersion. However, the immersion process resulted in the product with the highest overall quality according to the sensory analysis and presented the most appropriate texture according to the firmness values. Finally, in the evaluation of immersion, a significant influence of the CaCl2 immersion time (p<0.05) on the firmness values of the product was found, resulting in longer times leading to less firm products. Considering 10% as a commercial standard limit for weight loss, the fruit treated under immersion and coating processes can be stored for at least 12 days. The immersion process is highlighted because it improved the sensory characteristics with respect to the control (without treatment). Thus, it process gives added value to the fruit and is presented as a promising alternative for the postharvest treatment of cape gooseberries.

Strontium (Sr) is a trace element in human body that able to promote bone formation and inhibit bone absorption. The conversion coating of strontium phosphate (Sr-P) on the surface of titanium (Ti) can improve its biological properties, and has a wide application prospect in the fields of dentistry and orthopedics. In this present study, Sr-P coatings with SrHPO4 and Sr3(PO4)2 crystals on Ti are prepared by phosphate chemical conversion (PCC) treatment. And the effect of pH on the properties of Sr-P coatings is researched. The results prove that phase composition, morphology and corrosion resistance of coated Ti are different with the pH values in PCC solution. The morphologies of conversion deposition on Ti change from plat-like to cluster-like, and then homogeneous microcrystals, as pH value changed from 2.50 to 3.25. Only discrete SrHPO4 crystals are generating on substrate at lower pH value, while relative stable Sr3(PO4)2 and SrHPO4 crystals are growing and subsequently forming an integrated coating on Ti as pH is higher than 2.50. The corrosion resistance of coated Ti improves comparing with that of bare Ti because of forming Sr-P coatings with Sr3(PO4)2 phase. In addition, it is indicated that the Sr-P coatings can improve the adhesion and differentiation of BMSCs.

In this study, Ni50Ti50 powder was coated on the surface of graphite substrate (C) by plasma spraying process using a radio frequency inductively coupled plasma reactor. The coating was carried out by using 12- and 9-kW power under Ar atmosphere. The cross-section of coating layers and the surface were examined with SEM, EDX, XRD analysis and microhardness test. The thickness and quality of the coating increased with input power. Many pores were detected in the cross-sectional surface areas. Higher input power caused a better coating layer in NiTi alloy. The hardness of the coating layer decreases with higher input power.

Organic Coatings have potential applications in the prevention of metal corrosion in an aqueous solution. The protective effect of SEBS coated copper corrosion in NaCl 3% solution was investigated by using electrochemical methods. The main objective of this work is to find the optimal conditions of the protocol immersion to evaluate the effects of SEBS ratio and two-immersion time on the anticorrosive behaviour of copper in 3 wt % NaCl solution in order to determine the best conditions to produce a protective SEBS film on the copper surface. Response Surface Methodology (RSM) is used as an optimization method. The study’s findings show the combination of three environmental factors that minimize corrosion rate. The Box-Behnken Design (BBD) is working perfectly for the statistical significance of the model (ANOVA test). This analysis calculates the contribution value of each parameter in changing the value of the corrosion rate (CR) in not only individual but also synergistic cases. The optimized parameters were found to be a 2.17% of SEBS ratio, 20 min of immersion 1, and 21 min of immersion 2. The electrochemical impedance spectroscopy tests confirmed the results.

Advanced Nano structural hard coatings are thin materials films that range in thickness from a few nanometers to a few micrometers and are applied to different surfaces to increase their hardness and wear resistance. Physical vapor deposition (PVD) or chemical vapor deposition (CVD) methods are frequently used to deposit these coatings. These coating’s distinctive characteristics result from their microstructure, which is made up of material columns or grains with a diameter of only a few nanometers. Increased hardness, higher wear resistance, and improved tribological properties result from these short dimensions. In applications with significant wear and/or high contact pressures, such as cutting tools, bearings, and engine parts, the usage of sophisticated Nano structural hard coatings is crucial. Advanced Nano structural hard coatings include, 1. Amorphous carbon coatings with high hardness, low friction, and exceptional wear resistance are known as diamond-like carbon (DLC) coatings. DLC coatings are frequently used in a variety of industries, including the automotive, aerospace, and biomedical ones. 2. Coatings made of titanium nitride (TiN): These metallic coatings have high hardness and wear resistance. Cutting tool, machining, and aerospace industries frequently use TiN coatings. 3. Chromium nitride (CrN) coatings: These coatings have great corrosion resistance, good wear resistance, and high hardness. Cutting tools, gears, and bearings are just a few of the objects that use CrN coatings. 4. Tungsten carbide (WC) coatings: These coatings, which have a high degree of hardness and wear resistance, are frequently employed in cutting tools and other applications that require wear resistance. Advanced Nano structural hard coatings provide many advantages over conventional coatings, including better hardness, increased wear resistance, and improved tribological qualities. The automotive, aerospace, and biomedical industries are just a few that could use these coatings. In this paper the author will explain about the design synthesis and applications of advanced Nano structural hard coating in aerospace and automotive applications.

Biocidal compositions based on interpolyelectrolyte complexes and a low molecular weight antibiotic can become a promising material for creating biocidal coatings, as they combine wash-off resistance and dual biocidal action due to the biocide and the polycation. Molecular mass characteristics of polymers play essential role in physics and mechanical properties of the coatings. In this work, the properties of polydiallyldimethylammonium chloride (PDADMAC) coatings of various molecular weights are investigated and assumptions are made about the optimal molecular weight needed to create antibacterial compositions. To study the resistance to washing off and moisture saturation of the coatings, the gravimetric method was used, the adhesive properties of the coatings were studied by dynamometry. It has been established that an increase in molecular weight affects the wash-off resistance of coatings, but does not affect moisture absorption and adhesion mechanics of coatings. All samples of PDADMAC were demonstrated to exhibit the same antibacterial activity. Thus, when developing systems for creating antibacterial coatings, it must be taken into account that in order to create stable coatings. The requirement to use PDADMAC with a high degree of polymerization is necessary for control the desorption of coating during wash off-but not mandatory for the control of mechanical and antibacterial properties of the coating.

Millions of people use public transportation daily worldwide and frequently touch surfaces, thereby producing a reservoir of microorganisms on surfaces increasing the risk of transmission. Constant occupation makes sufficient cleaning difficult to achieve. Thus, an autonomous, perma-nent antimicrobial coating (AMC) could keep down the microbial burden on such surfaces. A photodynamic AMC was applied to frequently touched surfaces in buses. The microbial burden (colony forming units, cfu) was determined weekly and compared to equivalent surfaces in buses without AMC (references). The microbial burden ranged from 0 – 209 cfu/cm² on references and from 0 – 54 cfu/cm² on AMC. The means were 13.4 ± 29.6 cfu/cm² on references and 4.5 ± 8.4 cfu/cm² on AMC (p<0.001). The difference of microbial burden on AMC and references was al-most constant throughout the study. Considering a hygiene benchmark of 5 cfu/cm², the data yield an absolute risk reduction of 22.6 % and a relative risk reduction of 50.7 %. In conclusion, photo-dynamic AMC kept down the microbial burden, reducing the risk of transmission of microor-ganisms. AMC permanently and autonomously contributes to hygienic conditions on surfaces in public transportation. Photodynamic AMC therefore are suitable for reducing the microbial load and closing hygiene gaps in public transportation.

Background: Mucoadhesive polymers represent a major part of site-specific and localized retention strategies in oral drug delivery. Present research was designed to synthesize and characterize a novel mucoadhesive carbohydrate polymer (thiolated gum ghatti; TGG) which was further employed to fabricate mucoadhesive tablets of domperidone using an industrially viable compression coating technique. Methods: Thiolation of gum ghatti was achieved by the ester formation (esterification) between hydroxyl group and carboxyl group of gum ghatti and thioglycolic acid. Results: TGG was characterized by various physico-chemical techniques such as FTIR, XRD, SEM and DSC techniques. In rheological studies, the observed viscosities of pure gum-mucin were 45.45 and 71.75 mPas and that of thiolated gum were 78.7 and 112.58 mPas respectively in water and simulated gastric fluid. Signifi-cant increase in viscosity for thiolated gum may be attributed to increased macromolecular interactions responsible for enhanced mucoadhesive potential of thiolated gum. In-silico studies corroborate the role of mucin gum interaction and energetic stabilization for en-hanced mucoadhesion properties of thiolated gum. Ex-vivo mucoadhesion strength of gum ghatti and thiolated gum ghatti coated tablets was found to be ranging between 4.67± 0.79 to 8.99± 0.75 g and 11.76± 1.34 to 18.83± 2.07 g respectively. Conclusion: Thiolated gum ghatti may be regarded as a promising polymer for developing different mucoadhesive drug delivery systems.

In order to develop waterborne silicate anticorrosive coatings to replace solvent-based anticorrosive coatings used widely in ship’s industry, epoxy modified silicate emulsions were synthesized with different content of epoxy resin, then aqueous silicate zinc-rich coatings were prepared with synthesized silicate emulsion, triethylamine and zinc powder. The influence of the content of epoxy on the properties and chemical structure of modified emulsion, mechanical properties of silicate coatings, and the corrosion behavior of silicate zinc-rich coatings in 3.5% NaCl solution were investigated. The coating samples on steel were measured by immersion test, Tafel polarization test and electrochemical impedance spectroscopy (EIS) test with different immersion time. The results showed that epoxy modified silicate emulsions were successfully synthesized. With the increase of epoxy content, the viscosity and the solid content of modified emulsion increases, the impact resistance of the silicate coating raises, the pencil hardness decreases, but the adhesion is not affected. Epoxy modification can reduce to s certain extent the corrosion driving force of zinc rich coating and increase the impedance of the zinc-rich coating decreases with the increase of immersion time in 3.5% NaCl solution. With the increase of the epoxy content, the resistance value of the zinc-rich coating increases, indicating the ability of the coating to resist corrosive media is enhanced.

The concept of friction damper is widespread technique and used to reduce the structural vibrations in many industrial applications. These friction dampers are generally coated with low wear rate materials to reduce the fretting wear. This paper investigates the use of physical vapor deposition (PVD) nitride based AlTiN coating material applied over the stainless steel friction damper to enhance the damping capacity and to reduce the fretting wear. A friction test rig has been developed to measure the dynamic hysteresis characteristics of friction damper at high temperature (700 °C). The damping capacity and fretting wear analysis is carried out at room temperature, 300 °C and 600 °C. The force versus displacment characterisitcs curve is used to predict the damping capacity and fretting wear analysis is carried out at microscopic level for the comparision. It is observed that at room temperature AlTiN coated friction damper has not much influence to improve the damping capacity and to reduce the fretting-wear. However, at high temperature it has better damping capacity and less wear in comparision to uncoated friction damper. Wear behaviour in coated and uncoated damper is different at room temperature and at elevated temperature.

Background/Aim: There is continuing interest in engineering esthetic labial archwires. The aim of this study was to coat nickel-titanium (NiTi) and beta-titanium (β-Ti), also known as titanium molybdenum (TMA), archwires by plasma electrolytic oxidation (PEO) and to analyze the characteristics of the PEO-surfaces. Materials and Methods: PEO-coatings were generated on 0.014-inch NiTi and 0.19x0.25-inch β-Ti archwires. The surfaces were analyzed by scanning electron microscopy and stereomicroscopy. Cytocombability testing was performed with ceramized and untreated samples according to EN ISO 10993-5 in XTT-, BrdU- and LDH-assays. The direct cell impact was analyzed using LIVE-/DEAD-staining. In addition, the archwires were inserted in an orthodontic model and photographs were taken before and after insertion. Results: The PEO coatings were 15 to 20 µm thick and esthetically pleasing. The cytocompatibility analysis revealed good cytocompatibility results for both ceramized NiTi and β-Ti archwires. In the direct cell tests, the ceramized samples showed improved compatibility as compared to those of uncoated samples. However, bending of the archwires resulted in loss of the PEO-surfaces. Nevertheless, it was possible to insert the β-Ti PEO-coated archwire in an orthodontic model without loss of the PEO-ceramic. Conclusion: PEO is a promising technique for the generation of esthetic orthodontic archwires. Since the PEO-coating does not resist bending, its clinical use seems to be limited so far to orthodontic techniques using straight or pre-bended archwires.

The present study aims at deposition of zinc phosphate coatings with the incorporation of nano Titanium dioxide particles by chemical phosphating method. Zinc phosphate coatings were developed on low carbon steel by using nano TiO2 in the standard phosphating bath. The Coated low carbon steel samples were assessed for corrosion studies using electrochemical impedance spectroscopy and potentiodynamic polarisation techniques in 3.5% NaCl solution. Chemical composition of the coatings was analysed by energy dispersive X-ray spectroscopy (EDX). Significant variations in the coating weight, porosity and corrosion resistance were observed with the addition of nano TiO2 in the phosphating bath. Corrosion rate of nano TiO2 incorporated chemical phosphate coated samples was found to be 3.5 mpy which was 4 times less than the bare uncoated low carbon steel (~14 mpy). Electrochemical impedance spectroscopy studies revels in the reduction of porosity in nano TiO2 phosphate coated samples. It was found that nano TiO2 particles in the phosphating solution yielded phosphate coatings of higher coating weight, greater surface coverage and enhanced corrosion resistance than the normal zinc phosphate coatings (developed using normal phosphating bath).

We examine here the conductance changes associated with the change in spin state in a variety of different structures, using the example of the spin crossover complex [Fe(H2B(pz)2)2(bipy)] (pz= (pyrazol-1-yl)-borate and bipy = 2,2’-bipyridine) and [Fe(Htrz)2(trz)](BF4)] (Htrz = 1H-1,2,4-triazole) thin films . This conductance change is highly variable depending on the mechanism driving the change in spin state, the substrate and the device geometry. Simply stated, the choice of spin crossover complex used to build a device is not the only factor in determining the change in conductance with the change in spin state.

We demonstrate, in the context of Loop Quantum Gravity, the Quantum Holographic Principle, according to which the area of the boundary surface enclosing a region of space encodes a qubit per Planck unit. To this aim, we introduce fermion fields in the bulk, whose boundary surface is the two-dimensional sphere. The doubling of the fermionic degrees of freedom and the use of the Bogoliubov transformations lead to pairs of spin network’s edges piercing the boundary surface with double punctures, giving rise to pixels of area encoding a qubit. The proof is also valid in the case of a fuzzy sphere.

Results are presented concerning the influence on the water splitting process of enantiopure tartaric acid present in bulk solution. Stainless steel and electrodeposited nickel are used as working electrode (WE) surface. The latter is obtained by electrodeposition on the two poles of a magnet. The influence and role played by the chiral compound in solution has been assessed by comparing the current values, in cyclic voltammetry (CV) experiments, recorded in the potential range at which oxygen evolution reaction (OER) occurs. In the case of tartaric acid and nickel WE a spin polarization of about 4 % is found. The use of the chiral environment (bulk solution) and ferromagnetic chiral Ni electrode allows for observing the OER at a more favourable potential: about 50 mV (i.e. a cathodic, less positive, shift of the potential at which the oxygen evolution is observed).

Spin-orbit coupling and nonparaxiality effects during propagation of vortex vector light beams in a cylindrical graded-index waveguide are investigated by solving the full three-component field Maxwell’s equations. Symmetry breaking effects for left- and right-handed circularly polarized vortex light beams propagating in a rotationally symmetric graded-index optical fiber are considered. The mode-group delay in a graded-index fiber due to spin-orbit interaction is demonstrated. It is shown that the relative delay times between vortex pulses of opposite circular polarizations of the order of 10 ps/km can be observed in graded-index fibers for high-order topological charges.

The severe volumetric expansion of silicon nanoparticles (~400 %) limits their practical application as an anode material for next-generation lithium–ion battery (LIB). Here, we describe the fabrication and characterization of conformal polydopamine carbon shell encapsulating rattle-type silica@silicon nanoparticles (PDA−PEI@PVP−SiO2@Si) with tunable void structure prepared following a dual SiO2 template using (3–aminopropyl)triethoxysilane (APTES) as a self-catalytic, structure-directing agent to tetraethyl orthosilicate (TEOS) pretreated with polyvinylpyrrolidone (PVP K30) via modified Stöber process. Polyethylene imine (PEI) crosslinking facilitated the construction of interconnected three-dimensional bubble wrap-like carbon matrix structure through hydrothermal treatment, pyrolysis, and subsequent surface-protected etching. The composite anode material delivered 539 mAh·g−1 capacity after 100 cycles at 0.1 A·g−1, and 453 mAh·g−1 rate performance at 5 A·g−1. The satisfactory electrochemical performance of the PDA−PEI@PVP−SiO2@Si was attributed to the following: the rattle-type structure providing void space for Si volume expansion, PVP K30-pretreated APTES/TEOS SiO2 seeds via catalyst-free, hydrothermal-assisted Stöber protecting Si/C spheres upon etching, carbon coating strategy increasing Si conductivity while stabilizing the solid electrolyte interface (SEI), and PEI carbon crosslinks providing continuous conductive pathways across the electrode structure. The present work realizes a promising strategy to synthesize the tunable yolk–shell C@void@Si composite anode materials for high power/energy-density LIB applications.

Quantum physics is intrinsically probabilistic. The entropy of a quantum state quantifies the amount of randomness (or information loss) of such state. The degrees of freedom of a quantum state are position and spin, and upon their specification Born's rule in phase space defines randomness. We focus on the spin degree of freedom and elucidate the spin entropy. Then, we present some of its properties and show how entanglement increases spin entropy. Some speculative predictions on the decay of the $Z^0,W^{+,-}$ gauge bosons conclude the paper.

The spin-1/2 quantum transverse Ising model, defined on a ladder structure, with nearest-neighbor and four-spin interaction on a plaquette, is studied by using exact diagonalization and finite-size-scaling procedures. The quantum phase transition between the ferromagnetic and paramagnetic phases has been obtained in the thermodynamic limit. The critical transverse field decreases as the antiferromagnetic four-spin interaction increases, and reaches a multicritical point. However, the exact diagonalization approach was not able to capture the essence of the dimer phase beyond the multicritical transition.

We propose an experimental method for the unidirectional excitation of spin waves. By structuring Au nanowires arrays within a coplanar waveguide onto a thin yttrium iron garnet (YIG) film, we observe a chiral coupling between the excitation field geometry of the nanowires grating and several well-resolved propagating magnon modes. We report a propagating spin wave spectroscopy study with unprecedented spectral definition, wavelengths down to 130 nm and attenuation lengths well above the 100 μm over the 20 GHz frequency band. The proposed experiment paves the way for future non-reciprocal magnonic devices.

1D spin crossover (SCO) solids which convert between the low-spin (LS) and the high-spin (HS) states are widely studied in the literature due to their diverse thermal and optical characters which allows obtaining many original behaviors, such as large thermal hysteresis, incomplete spin tran-sitions, as multi-step spin transitions with self-organized states. In the present work, we investigate the thermal behaviors of a system of two-elastically coupled 1D mononuclear chains, using the electro-elastic model, by including an elastic frustration in the nearest neighbors (nn) bond length distances of each chain. The chains are made of SCO sites that are coupled elastically through springs with their nn and next-nearest neighbors. The elastic inter-chain coupling includes diagonal springs, while the nn inter-chains distance is fixed to that of the high-spin state. The model is solved using MC simulations, performed on the spin states and the lattice distortions. When we only frustrate the first chain, we found a strong effect on the thermal-dependence of the HS fraction of the second chain, whose, by lowering its transition temperature which is also accompanied with the appearance of a significant residual HS fraction at low temperature. In the second step, we frustrate both chains by imposing different frustration rates and found that, for high frustration values, the thermal dependence of the total HS fraction exhibits three step and even four step spin transitions. The careful examination of the spin state structures in the plateau regions revealed the existence of special antiferro-elastic structure of type LSLS-HSHS-LSLS-HSHS along the first chain, and HSHS-LSLS-HSHS-LSLS along the second, also showing that the two chains seem to be antifer-ro-elastically coupled. This type of organization is interesting, because it anticipates the possible existence of periodic structures made of alternate 1D antiferro-like HS-LS strings coupled in the ferro-like fashion along the interchain direction in the 2D case.

We present the Lagrangian and Hamiltonian formulations of a theory for spin 2 fields. The construction is developed in flat space-time. The construction in curved space-time is conceptually straightforward, although it is not unique. The theory is based on a symmetric tensor $S_{\mu\nu}$, contains two degrees of freedom of radiation, is motivated by the teleparallel formulation of general relativity, and displays a certain resemblance with Maxwell's theory for the electromagnetic field.

Abstract: I present a generalization of quantum electrodynamics which includes Diracmagnetic monop oles and the Salam magnetic photon. This quantum electromagnetodynamics has many attractive features. (1) It explains the quantization of electric charge. (2) It describes symmetrized Maxwell equations. (3) It is manifestly covariant. (4) It describes local four-potentials. (5) It avoids the unphysical Dirac string. (6) It predicts a second kind of electromagnetic radiation which can be veried by a tabletop experiment. An eect of this radiation may have been observed by August Kundt in 1885. Furthermore I discuss a generalization of General Relativity which includes Cartan's torsion. I discuss the mathematical denition, concrete description, and physical meaning of Cartan's torsion. I argue that the electric-magnetic duality of quantum electromagnetodynamics is analogous to the spin-mass duality of Einstein-Cartan theory. A quantum version of this theory requires that the torsion tensor corresponds to a spin-3 boson called tordion which is shown to have a rest mass close to the Planck mass. Moreover I present an empirically satised fundamental equation of unied eld theory which includes the fundamental constants of electromagnetism and gravity. I conclude with the remark that the concepts presented here require neither Grand Unication nor supersymmetry.

The interest in random fiber lasers (RFLs), first demonstrated one decade ago, is still growing and their basic characteristics have been studied by several authors. RFLs are open systems that present instabilities in the intensity fluctuations due to the energy exchange among their non-orthogonal quasi-modes. In this work, we present a review of the recent investigations on the output characteristics of a continuous-wave erbium-doped RFL, with emphasis on the statistical behavior of the emitted intensity fluctuations. A progression from the Gaussian to Lévy and back to the Gaussian statistical regime was observed by increasing the excitation laser power from below to above the RFL threshold. By analyzing the RFL output intensity fluctuations, the probability density function of emission intensities was determined, and its correspondence with the experimental results was identified, enabling a clear demonstration of the analogy between the RFL phenomenon and the spin-glass phase transition. A replica-symmetry-breaking phase above the RFL threshold was characterized and the glassy behavior of the emitted light was established. We also discuss perspectives for future investigations on RFL systems.

The rationalization of single molecule magnets’ (SMMs) magnetic properties by quantum mechanical approaches represents a major task in the field of the Molecular Magnetism. The fundamental interpretative key of molecular magnetism is the phenomenological Spin Hamiltonian and the understanding of the role of its different terms by electronic structure calculations is expected to steer the rational design of new and more performing SMMs. This paper deals with the ab initio calculation of isotropic and anisotropic exchange contributions in the Fe(III) dimer [Fe₂(OCH₃)₂(dbm)₄]. This system represents the building block of one of the most studied Single Molecule Magnets ([Fe₄RC(CH₂O)₃)₂(dpm)₆] where R can be an aliphatic chain or a phenyl group just to name the most common functionalization groups) and its relatively reduced size allows the use of a high computational level of theory. Calculations were performed using CASSCF and NEVPT2 approaches on the X-ray geometry as assessment of the computational protocol, which has then be used to evinced the importance of the outer coordination shell nature through organic ligand modelization. Magneto-structural correlations as function of internal degrees of freedom for isotropic and anisotropic exchange contributions are also presented, outlining for the first time the extremely rapidly changing nature of the anisotropic exchange coupling.

The reduction in rheological parameters and dissolution rate of precursors in geopolymer coatings during early hydration significantly contributes to sagging. This study aims to improve the sag resistance of these coatings by incorporating diatomite filler. Rheological testing was conducted to assess the impact of diatomite and its concentration on yield stress, plastic viscosity, and thixotropy of the geopolymer coatings. The results indicated that diatomite's large specific surface area and high reactivity have a significant influence on the rheological parameters and early dissolution rate of precursors. With a diatomite concentration of 1.1%, the coating exhibited a yield stress of 2.749 Pa and a plastic viscosity of 0.921 Pa·s, maintaining stability, homogeneity, and no sagging at a thickness of 600 μm. Furthermore, the highly active SiO2 in diatomite participates in the secondary hydration reaction of the geopolymer materials, leading to the formation of substantial C-(A)-S-H gel. This gel enhances internal interconnectivity within the coating, thereby improving its rheological and mechanical properties.

(1) Background: The aim of this study was to investigate the circadian rhythms of tongue features according to the effects of physiological phases over a 24-hour period. (2) Methods: Fifteen healthy participants aged 20 to 69 years were recruited. The participants did not have current chronic diseases or past diseases and had to meet the inclusion and exclusion criteria. The participants stayed at the Gil Hospital for a duration of 2 nights and 3 days. On the first day, at 18:00, they consumed their allocated portions of food and water and then completed a questionnaire. At approximately 21:00, their tongue images were acquired using a computerized tongue image acquisition system, following which they slept for 8 hours, commencing at 23:00. Measurements were taken from 07:00 through 21:00 on the second day, and the final acquisition was taken at 07:00 on the following morning, resulting in a total of eight images. The circadian rhythm was authenticated and quantified utilizing the single cosinor analysis, a technique for periodic regression analysis for fitting a 24-hour cosine curve. (3) Results: Cosinor analysis revealed that all tongue features were significantly related to circadian rhythm. (4) Conclusions: The results of this study may be important for considering the time of day at which the tongue is observed and tongue status is evaluated.

A new sustainable polypropylene terephthalate (PPT) coating was synthesized from recycled polyethylene terephthalate (PET) and applied on hydraulic concrete substrate to improve its durability. First step, PET bottles wastes were grinded and depolymerized by glycolysis using propylene glycol (PG), in a Vessel-type reactor (20–180 °C) to synthesize bis(2-hydroxypropyl)-terephthalate (BHPT), which was applied as coating to one-three layers on hydraulic concrete substrate, by brushing technique and polymerized (150 °C for 15 h) to obtain PPT. PET, BHPT and PPT were characterized by FT-IR, PET and PPT by TGA, and the PPT coatings by SEM (thickness), by ASTM-D3359-17 (adhesion) and by water contact angle (wettability). The durability of hydraulic concrete coated with PPT was studied by resist chloride ion penetration (ASTM-C1202-17), carbonation depth at 28 days (RILEM-CPC-18), and absorption water ratio (ASTM-C1585-20). The results demonstrated that the BHPT and PPT were synthetized (FT-IR), PPT had a similar thermal behaviour to PET (TGA); the PPT coatings had good adhesion to the substrate, with thicknesses of micrometric units; hydrophilic (similar to PET coatings), and the durability of hydraulic concrete coated with PPT (2-3 layers) improved (migration of chloride ions decreased, carbonation depth was negligible, and the absorption water ratio decreased).

Laser heat treatment is applied after coating. Evaluation of the results was performed by studying the microstructures by metallographic, SEM/EDX microscopy and the mechanical properties were obtained by microscopic hardness and abrasion resistance. The objective of this study was to investigate the effect of laser heat treatment on the wear resistance of metal coatings. The results show the influence of the microstructure and chemical composition of the electrodes used on the micro-hardness and wear resistance of the metal coatings.

A detailed structural investigation of a promising bio-based polymer, polyglycerol citrate poly-ester, obtained by bulk polycondensation of glycerol (Gly) against citric acid (Cit) under mild reaction was performed. This polymer was suggested to be well suited for coating seeds or similar agricultural applications. The reaction in conditions with and without catalyst use (sulfuric acid, H2SO4) was investigated, showing evidence that it is possible to modify the polymer solubility according to the ratio and catalyst utilization. 13C and 1H NMR indicated that synthesis catalyzed with Cit excess leads to higher esterification degrees of citrates groups. In contrast, the Gly moi-eties are more prominent in catalyzed polymers regardless of the excess monomers. Overall, a successful conversion of Gly and Cit into polyesters was attained, even without catalysis, enabling a simple route for large-scale production of this green material to be used as coating material. Tests on soybean seed coating with a PGCit solution of 75% indicated that the seed quality and ger-mination rate was not affected by PGCit coating, concluding that this polymer is promising for this application.

In order to further reduce the emissivity of the hydrophobic low infrared emissivity composite coating and improve the mechanical properties of the coating, the dispersant, adhesion enhancer, and defoamer were used to improve the dispersion state of the fillers, the interface structure, and the surface state of the hydrogen silicone oil modified polyurethane/Al composite coating. The effects of dispersant, adhesion enhancer, and defoamer on the micro-structure, emissivity, glossiness, hydrophobic property, and mechanical properties of the coating were systematically studied. The results show that the polycarboxylate anionic dispersant can obviously improve the dispersion state of flake Al powder and nano-SiO2 in the coating, so that the infrared emissivity of the coating can be reduced, and the coating can have higher hydrophobic and mechanical properties. The bonding strength between the resin matrix and the metal substrate of the coating can be significantly improved by the adhesion enhancer through the bridging action, so that the adhesion strength and impact strength of the coating can be significantly improved. The defoamer can significantly reduce the pores in the coating, so that the surface state of the coating can be significantly improved, and the mechanical properties of the coating can be significantly improved. The coating has the best emissivity (0.527), glossiness (4.3), adhesion strength (grade 1), impact strength (40 kg.cm), and hydrophobic property (water contact angle (WCA) is 140o) when the amount of dispersant, adhesion enhancer, and defoamer is 5 wt%, 4 wt%, and 1 wt%, respectively.

In the present study, a nanostructured FeAl coating was prepared by cold spraying of ball milled powder. Annealing treatment was applied to the coating to investigate its effect on the microstructure, phase structure and microhardness of the cold-sprayed nanostructured FeAl coating. The results showed that the FeAl phase was kept unchangeable when the coating annealed at the temperature above 500oC. Annealing temperature significantly influenced the microstructure and microhardness of cold-sprayed FeAl coating. With raising annealing temperature, the lamellar structure in the as-sprayed coating disappeared and a dense coating microstructure with fully bonding of deposited particles at their interfaces was achieved after annealing at 950oC. Nanograin growth of the FeAl phase occurred at an annealing temperature higher than 800oC. The microhardness of cold-sprayed FeAl coating remained about 400 Hv0.1 at the annealing temperature below 800oC and decreased to 300 Hv0.1 at 1100oC.

In this paper, applicability of the modified water-based yttria stabilized zirconia (YSZ) suspensions, including different dispersants, to produce plasma sprayed coatings with “columnar microstructure” is investigated. The effects of processing parameters like suspension liquid phase ethanol content, change of substrate roughness, and spray distance on the resulting coatings morphologies are investigated. The results showed that increasing ethanol concentration, substrate surface roughness, and the spray distance promote formation of coatings with columnar structure. Moreover, application of modified water-based suspensions including α-Terpineol dispersant has led to deposition of columnar coatings with comparable morphologies of coatings deposited from ethanol-based suspensions.

Peri-implantitis occurs at a significant rate, which is the leading cause of implant failure. The main reason for this unwanted complication is bacterial invasion and biofilm formation. To reduce the incidence of peri-implantitis, we constructed a carboxymethyl dextran (CMD) based nanomicelles antibacterial coating on microarc-oxidized titanium (MAO-Ti) surface. After cross-linking, the drug-loaded nanomicelles were spherical with a particle size of 130nm and uniformly dispersed. Zeta potential was negative, and the absolute value was greater than 10 mV, effectively avoiding micelles aggregation. It was observed by dynamic light scattering (DLS) that the stability of nanomicelles was significantly improved after cross-linking. The hemolysis rate of micelles was less than 5%, and the overall survival rate of human umbilical vein endothelial cells was more than 90%. After being coated on MAO-Ti surface, the cumulative drug release rate of drug-loaded nanomicelles reached 86.6% after 360 hours. Fluorescence staining of immobilized bacteria showed more dead bacteria on the coating surface, and the number of live bacteria was significantly reduced. It was concluded that dextran-based nanomicelles, which showed long-term drug release properties and excellent biocompatibility, are potential drug carriers for fabricating antibacterial coating on titanium surfaces.

Metallic thin-film materials and nanoparticles (mainly Silver (Ag)-based) are recently being used in many nano-technological applications including sensors, reflective heat-mirror coatings, and antibacterial coatings as well. The physical vapor deposition technique attracts significant attention for Ag-based nanocomposites with tailoring the structural and optical properties of metallic thin films thus allowing further improvements and application possibilities in various existing fields namely electronics, catalysis, magnetics, optics in alongside the environment and health and new emergent fields in, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of Silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques.

A phosphate/molybdate and cerium-modified phosphate/molybdate conversion coatings were deposited on a carbon steel surface and their protective and self-healing abilities were evaluated. Surface morphology and inner structure of the coatings were examined using FE-SEM-FIB and TEM techniques, chemical composition and element distribution depth profiles in conversion layers were determined using EDX measurements, whereas XPS was applied for the analysis of Mo and Ce oxidation states. Voltammetric measurements and EIS were performed to assess the corrosion behavior of the samples. The higher protective and stronger self-healing abilities were found for phosphate/molybdate/cerium conversion coating deposited in a sulphate-containing solution. This was attributed to higher values of both: total cerium and Ce(IV) content in the conversion layer as well as to lower number of structural defects in the coating. It was demonstrated that the micro-structural characteristics of protective coatings are also important in determining self-healing abilities.

This research was conducted to manufacture thermally expandable microspheres (TEMs) for vehicles’ underbody coating and to apply them on an industrial scale. TEMs heat resistance was studied depending on the ratios of a cross-linking agent and an initiator. This research focused on the content of a cross-linking agent and how it affected the results. The TEMs’ outer shell was thickened to solve the problem of the foam expansion ratio’s reduction that occurred due to the shrinkage after the maximum expansion (Tmax) was reached. After foaming, the cross-sectional thickness and surface of the sample with thickened outer shell were observed. The TEMs with the thickened shell showed the least shrinkage, which indicated excellent shrinkage stability, even after prolonged exposure to heat.

Electrochemical impedance (EI) measurements were performed to evaluate the nylon 66/-tetra-(para-aminophenyl) porphyrin (H₂T(p-NH₂)PP)/graphene oxide (GO) film coating on stainless steel and compared to the nylon/H₂T(p-NH₂)PP and nylon/GO film samples using 1M H₂SO₄ as electrolyte. The nylon/H₂T(p-NH₂)PP and nylon/GO composite films showed high electrochemical impedance in the order of 109 ohm-cm² and a system controlled by mass transfer, product of a diffusion process at low frequencies with a resistance up to 5 orders of magnitude, indicating the diffusion of protons through the coating and a decrease in the metal dissolution. Otherwise, the nylon/H₂T(p-NH₂)PP/GO film compound evaluated show good ionic conductivity and electrochemical stability in the acid environment, acting porphyrin as a catalyst to the passage of protons through the film, reducing its electrochemical impedance up to 7 orders of magnitude with respect to the compounds nylon/H₂T(p-NH₂)PP and nylon/GO. Likewise, good capacitance values are also shown by modifying the concentrations of porphyrin and GO reinforcing materials. These properties are important for technological applications, such as anticorrosion coating for bipolar plates or membrane in a fuel cell type PEM, super-capacitors, etc.

One method of creating a brass coating is through electrodeposition, which is most often completed in cyanide galvanic baths. Because of the toxicity of cyanides, many are working on the development of cyanide-free baths, which are promising but not satisfactory to replace the classic methods. The purpose of the study was to explore a new generation of non-aqueous cyanide-free baths based on 1-ethyl-3-methylimidazolium acetate ionic liquids. The study involved the formation of copper, zinc, and brass coatings. The influence of the bath composition, cathodic current density, and temperature was determined. The obtained coatings were characterized by their morphology, chemical composition, roughness, and corrosion resistance. It was found that the structure of the obtained coatings is strongly dependent on the process parameters. The three main structures observed were fine-grained, porous, and olive-like. To the best knowledge of the authors, it is the first time the olive-like structure was observed in the case of an electrodeposited coating. The Cu-Zn coatings consisted of 19–96 at.% copper and exhibited relatively strong corrosion resistance. High improvement of corrosion properties was found in the case of copper and brass coatings with an olive-like structure.

Reactions of Fe(II) with the tris-(pyridin-2-yl)ethoxymethane (py3C-OEt) tripodal ligand in presence of the pseudohalide ancillary NCE- (E = S, Se, BH3) ligands led to a series of three mononuclear complexes formulated as [Fe(py3C-OEt)2][Fe(py3C-OEt)(NCE)3]2·2CH3CN, with E = S (1), BH3 (2) and Se (3). Single crystal characterizations (complexes 1-2) and X-ray powder diffraction (complexes 1-3) reveal monomeric isomorph structures formed by the spin crossover (SCO) anionic [Fe(py3C-OEt)(NCE)3] complex, associated with the low spin (LS) cationic [Fe(py3C-OEt)2]2+ complex and two solvent acetonitrile molecules. In the [Fe(py3C-OEt)2]2+ cation, the Fe(II) is coordinated by two py3C-OEt tridentate ligands, while the [Fe(py3C-OEt)(NCE)3] anion displays a hexacoordinated environment involving three N-donor atoms of one py3C-OEt ligand and three nitrogen atoms arising from of the three (NCE) coligands. The magnetic studies show the presence of gradual SCO behavior for the three complexes: a one-step transition around 205 K for 1 and two step-transitions for compounds 2 and 3, centred at 245 K and 380 K for 2, and at 170 K and 298 K for 3. The magnetic behaviors of complexes 1 and 2 remain unchanged when heating up to 500 K, while complex 3 shows significant changes which are caused by the crystallisation solvent loss above room temperature.

Complex systems can be described as the network of interactions between their components. In directed networks, information, energy and matter flow in dominant directions. Undirected networks, on the other hand, cannot easily capture these asymmetries. The local flow of information depends on the node spin, which is a function of the number of incoming and outgoing links attached to it. And yet, how the heterogeneous association between in-degree and out-degree constraints global dynamics remains poorly understood. Here, we develop a new theoretical model to study the relationship between node directionality and global flow dynamics. Our computational analysis of random and scale-free directed networks indicates that structural diversity constrains the dimensionality of reachable dynamical space. These results suggest how local directionality might be an universal driver of global dynamics in many systems, from social networks, to technological systems to the connectome.

An analysis is presented of the possible existence of a second anomalous dipole moment of Dirac’s particle next to the angular one. It includes a discussion why, in spite of his own derivation, Dirac has doubted about its relevancy. It is shown why since then it has been overlooked and why it has vanished from leading textbooks. A critical survey is given on the reasons of its reject, including the failure of attempts to measure and the perceived violations of time reversal symmetry and chargeparity symmetry. It is emphasized that the anomalous electric dipole moment of the pointlike electron (AEDM) is fundamentally different from the quantum field type electric dipole moment of an electron (eEDM) as defined in the standard model of particle physics and that its measurement requires different instrumentation. A proposal has been described how to prove or disprove its existence by experiment. Moreover, by reference from literature, the possible impact is discussed in the nuclear domain and in the gravitational domain.

The structural, electronic and magnetochemical properties of the star-shaped polyoxopalladate [Pd₁₅O₁₀(SeO₃)₁₀]¹⁰⁻ (POPd) and its lanthanide functionalized derivatives have been investigated on the basis of density functional theory followed by a ligand field analysis using the Radial Effective Charge (REC) model. Our study predicts that heteroPOPd is a robust cryptand that enforces D_5h symmetry around the encapsulated Ln³⁺ centers. This rigid coordination environment favors interesting potential magnetic behavior in the Er and Ho derivatives, which may be of interest for molecular spintronics and quantum computing applications.

Due to the high temperature limitation associated with silicon, SiC, Si₃N₄, TiC, TiN, TiB₂, cBN, CNx, SiO₂, Al₂O₃ and novel multicomponent nanocomposites polymer derived ceramics (PDC) based thin films like Si-C-N, Ti-Si-B-C-N and Si-O-CN that are compatible with silicon and have a wider range of operation in ambient conditions are being investigated. Apart from small scale electro-mechanical devices like N/MEMS, sensors, areas like metallurgical protection, water purification, energy storage, bio medical implants and aerospace have been benefited. The cross-sectional study involving the role of oxygen and nitrogen dissolution at different interfacial configurations has been presented.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

Tungsten carbide (WC) was well known as a wear-resistant material. Iron-based pow-der was suitable for remanufacturing of cast iron engine parts. To improve the wear resistance of the remanufactured iron-based cast iron engine parts, WC-Co was intro-duced into iron-based powders to prepare composite coatings for cast iron engine components. In this work, FeAlC-x(WC-Co) composite coatings were prepared by plasma transfer arc on compacted graphite cast iron. The influences of WC-Co con-tents in the Fe-AlC-x(WC-Co) composite coatings on the microstructure and properties of the composite coatings were investigated. The composite coatings contained γ-Fe, α-Fe, WC and Fe3W3C mainly. The microhardness of FeAlC-x(WC-Co) composite coatings had the highest hardness of 814 HV0.2, the-lowest coefficient of 0.5 and the lest wear mass loss of 1.3mg when the weight content of WC-Co in the composite coating was 20wt%. As compared with the FeAlC coating, FeAlC-x(WC-Co) composite coating achieved the effect of reducing friction and wear resistance simultaneously, which resulted from the self-lubricating effect of graphite and high wear-resistance of carbides in the claddings.

Electroluminescence (EL) is an innovative technology in the lighting area. The EL device's main structure consists of a phosphor layer sandwiched by two electrodes. In this work, several alternating current EL devices have been developed by applying a set of sequential layers with combinations of in-house prepared inks and commercially available ink as a phosphor layer. A flexible polyester textile substrate was functionalized with inks by spray coating technique, after knife-coated an interfacial layer directly on the surface. A thorough study was carried out on the phosphor layer composition to optimize the EL device performance, more precisely the illuminance intensity and the illuminance homogeneity. The developed phosphor layer was composed of zinc sulphide doped with copper (between 30.0 to 38.1 wt%) and diluted by using a diluent at different ratios (28.0 to 35.5 wt%). The best peak illuminance intensity of 61 lux was obtained when the phosphor ink presented 35.4% ZnS:Cu and was diluted with 33.0% diluent. The aim of this study to determine the best formulation of the phosphor layer, which can be highly promising for further developments of EL devices, taking in account different applications in market.

The (Ti, Nb)(C, B)/IN625 composite coating with both homogeneous and defect-free microstructure were successfully prepared by in situ on the surface of 42CrMo steel using the coupling of the ultra-high-speed laser cladding (EHLA in German) technology with the direct reaction synthesis (DRS) technology, and were comparatively analyzed with the IN625 coating prepared by the EHLA. The microstructure of the fused cladding layer was investigated by selected scanning electron microscopy (SEM), energy dispersive spectrometer (EDS) and double spherical aberration transmission electron microscopy (DSA-TEM). The residual stress distribution on both sides of the fused cladding interface was characterised by nanoindentation stress test based on the modified O&P method and the G&S energy method. The results show that the interface of (Ti, Nb)(C, B)/IN625 composite coatings is affected by about 670 kJ Joule heat released from the in-situ reaction, and the interfacial width reaches 24 μm, so that it is 6 times higher than that of IN625 coating prepared by EHLA, which effectively reduces the stress gradient in the interfacial region and alleviates the stress mismatch on both sides of the interface. However, the surface hardness of (Ti, Nb)(C, B)/IN625 composite coating is lower than that of the IN625 coating, with a value of about 240 HV0.2, and the average wear weight loss was only 10% of that of the IN625 coating, which is on the one hand attributed to the in-situ authigenic TiCB, TiC, NbMo3B4, and NbMo2B2 phases supporting the (Ti, Nb)(C, B)/IN625 composite coating substrate to achieve the abrasion reduction and wear resistance. On the other hand, it is attributed to the formation of nano-equiaxial ultrafine grains in the depth range of 250 nm below the wear surface area by the coupling of the three fields of plastic rheology-heat-force, which dynamically strengthens the wear surface.

Tablets are the most used solid dosage form in medical treatments. The realistic modeling 1 of such specific object shapes in computer simulations has been demonstrated already by the author 2 for bi-convex round tablets but needs to be extended for a wider range of tablet shapes. Moreover, 3 the number of tablets must be large enough to simulate industrial drum coaters, which are typically 4 used for film coating processes. Whilst this long lasting process where tablets flow continuously, 5 tablets are loaded by frequent changes of individual contacts. Using a tailored simulation tool named 6 pharmAssist , written for GPUs (modern massively parallel processors in graphics cards and HPC 7 accelerators), we implemented the widely used oblong tablet shape. We are able to simulate flows 8 involving industrial scale number of such tablets. Data mining allows for statistical analyzis of 9 pair-wise contacts of different geometric features. Our simulation results serves as an observation 10 space, which cannot be addressed by experimental analyzis and will help to avoid degradation of 11 tablets like chipping or other defect phenomena. This paper reflects current development work in 12 order to extend the DEM with a new shape class, which comprises the modelling of compacted or 13 extruded objects, which have a smooth exterior, a flat band and sharp contour edges

In recent years, there has been growing interest in thermal spray techniques using suspension or solution-based coatings. These techniques offer precise control over particle size and microstructure, improving feedstock flowability and allowing for high-quality coatings customization. Spray parameters, such as stand-off distance (SOD) and feedstock flow rate, can alter the performance and characteristics of these coatings. Geothermal power plant heat exchangers often face issues like corrosion, scaling, and fouling. These issues could be mitigated, at least in part, by the use of spray coatings. In this study, TiO2 coatings were applied to a carbon steel substrate using suspension plasma spray (SPS) to enhance the performance of geothermal heat exchanger materials. The impact of SOD (50, 75, and 100mm) and feedstock flow rate (10, 20, and 30 ml/min) on these coatings was examined through various techniques, including SEM, profilometry, XRD, and adhesion testing. The results demonstrated that coatings deposited using 10ml/min feedstock flow rate were well-adhered to the substrate due to efficient melting of coating material but as the SOD and feedstock flow rate increase due to poor thermal and kinetic energy exchange between the torch and feedstock particles, adhesion between coating and substrate decreases. smaller SODs led to more compact coatings, while higher feedstock flow rates increased coating porosity. Smaller SODs and lower flow rates resulted in well-adhered coatings, offering valuable insights for advancing geothermal heat exchanger coatings.

The process of Thermal spray is effective for creating a metal matrix composite (MMC) by embedding zirconium diboride reinforcement into a molybdenum matrix. This allows for the combination of beneficial properties in a new composite, as both materials have a high The materials Mo and ZrB2 possess different characteristics. For example, Mo has a melting point of 2622 ◦C while ZrB2 has a higher melting point of 3246 ◦C. Additionally, Mo has a high thermal conductivity of 139 W/m◦C compared to ZrB2's thermal conductivity of 24 W/m◦C. However, both materials have good thermal shock resistance, and Mo has a low coefficient of thermal expansion of 5.35 µm/m◦C while ZrB2 has a coefficient of thermal expansion of 5.8 × 10−6 K−1., as well as the ability to maintain strength at elevated temperatures and stability in extreme environments. The study focused on creating Mo/Zrb2 composites using a thermal spray coating technique, varying the parameters of spraying distance, number of passes, and gas pressure, and testing the resulting castings to evaluate their hardness and Young's Modulus. The primary objective of the research was to use the Taguchi technique for identifying the optimal parameters for generating the highest Young's Modulus and hardness for the castings. The Taguchi method integrates experimental and analytical principles to identify the most significant parameter affecting the response, which can significantly enhance overall performance. The study found that the optimal parameters were a spraying distance of 20 cm, gas pressure of 6 bar, and the number of passes of 18. The Taguchi method accurately predicted the parameters that produced the highest properties for the composite coatings, which demonstrated good surface formation without hot cracks and fewer pores, with well-formed metallurgical bonding between the coating and the substrate.

Microcrystalline and near nanocrystalline AlCrFeCoNi high-entropy alloy (HEA) coatings were applied on Inconel 718 superalloy using air plasma spraying (APS) process. High-temperature oxidation behavior of the microcrystalline and near nanocrystalline AlCrFeCoNi HEA coated superalloy were examined at 110°C under the air atmosphere for 50 cycles under cyclic heating and cooling (1 h for each cycle). The oxidation kinetics of both nanocrystalline and microcrystalline coated superalloy was accordingly analyzed by weight change measurement. It was noticed that the uncoated and coated followed the parabolic rate law of the oxidation. X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive X-ray analysis (EDS), and elemental mapping techniques were used to analyze the oxidized coated and uncoated samples. In the HEA coated superalloy, Fe, Ni, Co, and Al were oxidized in the inter-splat region, whereas the splats which consist mainly of Ni and Cr remained unoxidized. Because of the formation of compact and adhesive thin NiO, CoO oxides, and spinels together with the Al2O3 oxide scale on the surface of the coating during oxidation, the developed nanocrystalline HEA coating shows better oxidation resistance than the microcrystalline HEA coating.