In this paper, the power quality of interconnected microgrids is managed using a Model Predictive Control (MPC) methodology which manipulates the power converters of the microgrids in order to achieve the requirements. The control algorithm is developed for the microgrids working modes: grid-connected, islanded and interconnected. The results and simulations are also applied to the transition between the different working modes. In order to show the potential of the control algorithm, a comparison study is carried out with classical Proportional-Integral Pulse Width Modulation (PI-PWM) based controllers. The proposed control algorithm not only improves the transient response in comparison with classical methods but also shows an optimal behavior in all the working modes, minimizing the harmonics content in current and voltage even with the presence of non-balanced and non-harmonic-free three-phase voltage and current systems

High-penetration of Distributed Energy Resources (DER) in low voltage distribution grids, mainly photovoltaics (PV), might lead to overvoltage in the point of common coupling. Volt-VAr is one of the common control functions for DER power converters used to enhance the stability and the reliability of the voltage in the distribution system and, thus, fulfilling the network operator requirements. In this study, a centralized algorithm will provide local Volt-VAr control parameters to each PV inverter, based on the electrical grid characteristics where each equipment is installed. Since accurate information of grid characteristics is typically not available, the parametrization of the electrical grid is done using power meter data in DER location and a voltage sensitivity matrix. The algorithm has different optimization modes to both minimize voltage deviation and line current. In order to validate the effectiveness of the algorithm and its deployment in real infrastructure, it has been tested in an experimental setup with PV emulators in a set of 5-day tests. Volt-VAr control algorithm successfully adapted its parameters based on grid topology and PV inverter characteristics, achieving a voltage reduction up to 25% of the allowed voltage deviation.

Although different assessments and evaluations of Dual-Miller cycle performed, specified output power and thermal performance associated with engine determined. Besides, multi objective optimization of thermal efficiency, Ecological Coefficient of performance ( ) and Ecological function ( ) by the mean of NSGA-II technique and thermodynamic analysis performed. The Pareto optimal frontier obtaining the best optimum solution is chosen by fuzzy Bellman-Zadeh, LINMAP, and TOPSIS decision-making techniques. Based on the results, performances of dual-Miller cycles and their optimization are improved.

Learning disorders (LD) are diagnosed in children impaired in the academic skills of reading, writing and/or mathematics. Children with LD usually show a slower resting-state electroencephalogram (EEG), with EEG patterns corresponding to a neurodevelopmental lag. LD-children also show a consistent cognitive impairment in working memory (WM), including an abnormal task-related EEG with an overall slower EEG activity of more delta and theta power, and less gamma activity in posterior sites; task-related EEG patterns considered indices of an inefficient neural resource management. Neurofeedback (NFB) treatments aimed at normalizing the resting-state EEG of LD-children have shown improvements in cognitive-behavioral indices and diminished EEG abnormalities. Given the typical findings of a WM impairment in LD-children; we aimed to explore the effects of a NFB treatment in the WM of children with LD, by analyzing the WM-related EEG power-spectrum. We recruited 18 children with LD (8-10 years old). They performed a Sternberg-type WM-task synchronized with an EEG of 19 leads (10-20 system) twice in pre-post treatment conditions. They went through either 30 sessions of a NFB treatment (NFB-group, n= 10); or through 30 sessions of a placebo-sham treatment (Sham-group, n= 8). We analyzed the before-after treatment group differences for the behavioral performance and the WM-related power-spectrum. The NFB group showed faster response times in the WM-task post-treatment. They also showed an increased gamma power at posterior sites and a decreased beta power. We explain these findings in terms of NFB improving the maintenance of memory representations coupled with a reduction of anxiety.

Neuroscientists are able to detect physical changes in information entropy in available neurodata. However, the information paradigm is inadequate to fully describe nervous dynamics and mental activities such as perception. This paper provides an effort to build explanations to neural dynamics alternative to thermodynamic and information accounts. We recall the Banach–Tarski paradox (BTP), which informally states that, when pieces of a ball are moved and rotated without changing their shape, a synergy between two balls of the same volume is achieved instead of the original one. We show how and why BTP might display this physical and biological synergy meaningfully, making it possible to tackle nervous activities. The anatomical and functional structure of the central nervous system’s nodes and edges allows to perform a sequence of moves inside the connectome that doubles the amount of available cortical oscillations. In particular, a BTP-based mechanism permits scale-invariant nervous oscillations to amplify and propagate towards far apart brain areas. Paraphrasing the BPT’s definition, we could state that: when a few components of a self-similar nervous oscillation are moved and rotated throughout the cortical connectome, two self-similar oscillations are achieved instead of the original one. Furthermore, based on topological structures, we illustrate how, counterintuitively, the amplification of scale-free oscillations does not require information transfer.

Generator automatic voltage control device (AVC) is an automatic voltage and reactive power optimization control terminal on the power plant side. Aiming at improving the performance of generator automatic voltage control device, this paper introduces a detection method of AVC substation performance based on virtual dispatching terminal environment. During the testing, the upper computer of redundant power plant is connected to the virtual dispatching terminal environment to simulate the sending instructions of AVC master station, the behavior of AVC sub stations and the excitation system of generators. The performance of AVC substation is evaluated according to the feedback adjustment results, which can effectively detect the abnormal behavior of AVC substation in power plant.

The energy efficiency of grinding depends on the appropriate selection of cutting conditions, grinding wheel and workpiece material. Additionally, the estimation of specific energy consumption is a good indicator to control the energy consumed during the grinding process. Consequently, this study develops a model of material removal rate to estimate the specific energy consumption based on the measurement of active power consumed in a plane surface grinding of C45K with different thermal treatments and AISI 304. This model identifies and evaluates the power dissipated by sliding, ploughing and chip formation in a industrial-scale grinding process. Furthermore, the instantaneous positions of the abrasive grains during cutting are described to study the material removal rate. The estimation of specific chip formation energy is similar to that described by other authors in laboratory scale, which allows to validate the model and experiments. Finally, the results show that the energy consumed by sliding is the main phenomenon of energy dissipation in industrial-scale grinding process, where it is denoted that sliding energy by volume unity decreases as the depth of cut and speed of workpiece increase.

Finding out how cells with the same genome change fates in differentiation commitment is a challenge of biology. We used MCF-7 breast cancer cells treated with the ErbB2 ligand heregulin (HRG), which induces differentiation, to address if and how the constitutive pericentromere-associated domains (PADs) may be involved in this process. PAD-specific repressive heterochromatin (H3K9me3) and active euchromatin (H3K4me3) marking, centromere (CENPA) labelling, qPCR, acridine-orange-DNA structural test, and microscopic image analysis were applied. We found a two-step DNA unfolding, at 15-20 min and 60 min after HRG treatment, coinciding with bi-phasic activation of the early response genes (c-FOS family) and two steps of critical phase transition which were revealed in transcriptome studies. In control, the distribution of PAD number and size displays a power-law scaling with a boundary at the nucleolus. PADs’ clustering correlates with centromere numbers. 15 min after HRG treatment, the unravelling of PADs occurs, coinciding with the first step of euchromatin unfolding. The second step is associated with transcription of long-non-coding-RNA from satellite III DNA. We hypothesize that splitting of the PAD clusters under the critical size threshold of the silencing domain abrupts position effect variegation. It allows the first genome transcription avalanche to occur, starting differentiation commitment.

This paper aims at presenting an energy management strategy (EMS) based upon optimal control theory for a battery-supercapacitor hybrid power system. The hybrid power system consists of a Lithium-ion battery and a supercapacitor with associated bidirectional DC/DC converters. The proposed EMS aims at computing adaptive gains using salp swarm algorithm and load following control technique to assign the power reference for both the supercapacitor and the battery while achieving optimal performance and stable voltage. The DC-DC converter model is derived utilizing the first-principles method and compute the required gains to achieve the desired power. The fact that the developed algorithm takes disturbances into account increases the power ele-ments’ life expectancies and supplies the power system with the required power

The current revolution in communication and information technology is facilitating the Internet of Things (IoT) infrastructure. Wireless Sensor Networks (WSN) are a broad category of IoT applications. However, power management in WSN poses a significant challenge when the WSN is required to operate for a long duration without the presence of a consistent power source. In this paper, we develop a batteryless, ultra-low-power Wireless Sensor Transmission Unit (WSTx) depending on the solar-energy harvester and LoRa technology. We investigate the feasibility of harvesting ambient indoor light using polycrystalline photovoltaic (PV) cells with a maximum power of 1.4mW. The study provides comprehensive power management design details and a description of the anticipated challenges. The power consumption of the developed WSTx was 21.09µW during the sleep mode and 11.1mW during the operation mode. The harvesting system can harvest energy up to 1.2mW per second, where the harvested energy can power the WSTx for six hours with a maximum power efficiency of 85.714%.

Many Caribbean island nations have historically been heavily dependent on imported fossil fuels for both power and transportation, while at the same time being at an enhanced risk from the impacts of climate change, although their emissions represent a very tiny fraction of the global total responsible for climate change. Small island developing states (SIDS) are among the leaders in advocating for the ambitious 1.5°C Paris Agreement target and the transition to 100% sustainable, renewable energy systems. In this work we present three central results. First, we show through GIS mapping of all Caribbean islands the potential for near-coastal deep-water as a resource for Ocean Thermal Energy Conversion (OTEC) and couple these results with an estimate of the countries for which OTEC would be most advantageous due to a lack of other dispatchable renewable power options. Second, hourly data have been utilized to explicitly show the trade-offs between battery storage needs and dispatchable renewable sources such as OTEC in 100% renewable electricity systems, both in technological and economic terms. Finally, the utility of near-shore, open-cycle OTEC with accompanying desalination is shown to enable a higher penetration of renewable energy and lead to lower system levelized costs than those of a conventional fossil fuel system.

Purposely slow velocity resistance exercise (i.e., 10 s concentric and eccentric phases) is a popular training method, but limits the loads that can be lifted (e.g., <50% 1 RM). This study compared the biomechanical properties of purposely slow velocity (SLOW) and traditional resistance exercise (TRAD) that uses maximal lifting velocities. Healthy resistance-trained men (n=5) performed two testing sessions (barbell squat and bench press) in random-order; a SLOW session (1 set x 10 repetitions at 28% 1 RM, 10 s concentric & eccentric), and a TRAD session (3 x 10 at 70% 1 RM, controlled eccentric and maximal concentric). A force plate and linear position transducer were used to collect kinetic and kinematic data for every repetition of both protocols (α = 0.05). For both exercises, both concentric and eccentric mean force (N) and power (W) for each repetition was greater for TRAD. When the entire training session (squat + bench press) was examined, SLOW exhibited greater time under tension, while TRAD produced greater work (J) and impulse (N·s). Contrary to suggestions in both the lay and scientific literature, purposely slow resistance exercise produced less force, power, and work than traditional velocity resistance exercise.

Let be a power function $f_{r,M}(s)$ defined for every $s$ within the finite set $M$ as follows $$f_{r,M}(s)= \begin{cases} s^r, \ &s\in M,\\ 0, \ &\mathrm{otherwise}. \end{cases} $$ Let a discrete convolution of $f_{r,M}(s)$ be denoted as follows $\mathrm{Conv}_{r,M}[n]=(f_{r,M}*f_{r,M})[n]$. Let a real coefficients $A_{m,j}$ be given by the following recurrence $$ A_{m,j} = \begin{cases} 0, & \mathrm{if } \ j<0 \ \mathrm{or } \ j>m, \\ (2j+1)\binom{2j}{j} \sum_{d=2j+1}^{m} A_{m,d} \binom{d}{2j+1} \frac{(-1)^{d-1}}{d-j} B_{2d-2j}, & \mathrm{if } \ 0 \leq j < m, \\ (2j+1)\binom{2j}{j}, & \mathrm{if } \ j=m. \end{cases} $$ In this paper we show that for every $n>0$ the following odd-power identities involving coefficients $A_{m,j}$ and convolution transform $\mathrm{Conv}_{r,M}[n]$ hold $$ \begin{split} n^{2m+1}+1&=\sum_{r=0}^{m}A_{m,r}\mathrm{Conv}_{r,\mathbb{N}}[n],\\ n^{2m+1}-1&=\sum_{r=0}^{m}A_{m,r}\mathrm{Conv}_{r,\mathbb{Z}_{>0}}[n],\\ n^{2m+1}&=\sum_{r=0}^{m}A_{m,r}\sum_{k=1}^{n} k^r(n-k)^r\\ &=\sum_{r=0}^{m}A_{m,r}\sum_{k=0}^{n-1} k^r(n-k)^r. \end{split} $$

The European Union Green Deal aims at curbing planet-warming greenhouse gas emissions and introducing clean energy production. But to achieve energy efficiency, the opportunity cost of different energies must be assessed. In this article, we analyse two different systems for the treatment of wastewater that, at the same time, produce energy for its own operation. On the one hand, high-rate algal ponds system (HRAP) is considered; on the other hand, we study a conventional activated sludge system which uses photovoltaic power (AS+PV). This paper offers a viability analysis of both systems based on the capacity to satisfy their energetic consumption. In order to assess this viability, the probability of not achieving the energy consumption threshold at least one day is studied. The results point that the AS+PV system self-sufficiency is achieved using much lesser surfaces than those of HRAP system (for the former, less than 6.500 m2, for the latter 40.000 m2). However, the important AS capital cost makes still the HRAP system more economic, although storage provides a great advantage for using the AS+PV in locations where we have a lot of irradiance. This viability analysis, along with the opportunity cost analysis, will be used to assess these two projects devoted to the treatment of wastewater.

Three-phase AC electric arc furnace (EAF) is a typical non-linear load, causing many power quality problems. Most of the researches on the voltage problems of EAF mainly focus on the voltage fluctuation, and less on the transient voltage problems caused by EAF short circuit and open circuit. In this paper, the relationship between voltage and current of EAF is obtained by combining hyperbolic function and exponential function, then the white noise and chaotic circuit are added to establish the EAF model which is suitable for the study of voltage fluctuation and transient voltage. This paper analyzes the causes of the transient voltage problem of the EAF, calculates the short-circuit current, reactive impact and the influence on voltage at the point of common coupling (PCC) in the three-phase short-circuit of the EAF, and compares the calculation results with the simulation results to prove the accuracy of this model. The results show that the reactive impact of three-phase short circuit is about twice as much as that of normal operation of EAF, resulting in about 30% voltage sag at the PCC, which is very unfavorable to the power grid. This paper provides reference for transient power quality evaluation and dynamic reactive power compensation of EAF.

In power systems, flow allocation (FA) methods allow to allocate usage and costs of the transmission grid to each single market participant. Based on predefined assumptions, the power flow is split into isolated generator specific or producer specific sub-flows. Two prominent FA methods, Marginal Participation (MP) and Equivalent Bilateral Exchanges (EBE), build upon the linearized power flow and thus on the Power Transfer Distribution Factors (PTDF). Despite their intuitive and computationally efficient concept, they are restricted to networks with \emph{passive} transmission elements only. As soon as a significant number of \emph{controllable} transmission elements, such as High-voltage direct current (HVDC) lines, operate in the system, they loose their applicability. This work reformulates the two methods in terms of Virtual Injection Patters (VIP) which allows to efficiently introduce a shift parameter $q$, tuning contributions of net sources and net sinks in the network. Major properties and differences of the methods are pointed out. Finally, it is shown how the MA and EBE algorithm can be applied to generic meshed AC-DC electricity grids: Introducing a \emph{pseudo-impedance} which reflects the operational state of controllable elements, allows to extend the PTDF matrix under the assumption of knowing the current system's flow. Basic properties from graph theory are used for solving the pseudo-impedance dependent on the position in the network. This directly enables \emph{e.g.} HVDC lines to be considered in the MP and EBE algorithm. The extended methods are applied to a low-carbon European network model (PyPSA-EUR) with a spatial resolution of N=181 and an 18\% transmission expansion. The allocations of VIP and MP, show that countries with high wind potentials profit most from the transmission grid expansion. Based on the average usage of transmission system expansion a method of distributing operational and capital expenditures is proposed. Further it is shown, how injections from renewable resources strongly drive country-to-country allocations and thus cross-border electricity flows.

Accurate forecasting of wind power generation plays a key role in improving the operation and management of a power system network and thereby its reliability and security. However, predicting wind power is complex due to the existence of high non-linearity in wind speed that eventually relies on prevailing weather conditions. In this paper, a novel hybrid deep learning model is proposed to improve the prediction accuracy of very short-term wind power generation for the Bodangora Wind Farm located in New South Wales, Australia. The hybrid model consists of convolutional layers, gated recurrent unit (GRU) layers and a fully connected neural network. The convolutional layers have the ability to automatically learn complex features from raw data while the GRU layers are capable of directly learning multiple parallel sequences of input data. The data sets of five-minute intervals from the wind farm are used in case studies to demonstrate the effectiveness of the proposed model against other advanced existing models, including long short-term memory (LSTM), GRU, autoregressive integrated moving average (ARIMA) and support vector machine (SVM), which are tuned to optimise outcome. It is observed that the hybrid deep learning model exhibits superior performance over other forecasting models to improve the accuracy of wind power forecasting, numerically, up to 1.59 per cent in mean absolute error, 3.73 per cent in root mean square error and 8.13 per cent in mean absolute percentage error.

History is often thought to be dull and boring – where large numbers of facts are memorized for passing exams. But the past informs the present and future, especially in delineating the context surrounding specific events that, in turn, help provide a deeper understanding of their causes and implications. Scientific progress (whether incremental or breakthroughs) is built upon prior work. Chronological examination of computational chemistry’s evolution reveals the existence of major “epochs” (e.g., transition from semi-empirical methods to first principles calculations), and the centrality of key ideas (e.g., Schrodinger equation and Born Oppenheimer approximation) in potentiating progress in the field. The longstanding question of whether computing power (both capacity and speed) or theoretical insights play a more important role in advancing computational chemistry was examined by taking into account the field’s development holistically. Specifically, availability of large amount of computing power at declining cost, and advent of graphics processing unit (GPU) powered parallel computing are enabling tools for solving hitherto intractable problems. On the other hand, this essay argues (using Born Oppenheimer approximation as an example) that theoretical insights’ role in unlocking problems through simple (but insightful) assumptions is often overlooked. Collectively, the essay should be useful as a primer for appreciating major development periods in computational chemistry, from which counterfactual questions illuminate the relative importance of theoretical insights and advances in computer science in moving the field forward.

Attackers are perpetually modifying their tactics to avoid detection and frequently leverage legitimate credentials with trusted tools already deployed in a network environment, making it difficult for organizations to proactively identify critical security risks. Network traffic analysis products have emerged in response to attackers’ relentless innovation, offering organizations a realistic path forward for combatting creative attackers. Additionally, thanks to the widespread adoption of cloud computing, Device Operators (DevOps) processes, and the Internet of Things (IoT), maintaining effective network visibility has become a highly complex and overwhelming process. What makes network traffic analysis technology particularly meaningful is its ability to combine its core capabilities to deliver malicious intent detection. In this paper, we propose a novel darknet traffic analysis and network management framework to real-time automating the malicious intent detection process, using a weight agnostic neural networks architecture. It is an effective and accurate computational intelligent forensics tool for network traffic analysis, the demystification of malware traffic, and encrypted traffic identification in real-time. Based on Weight Agnostic Neural Networks (WANNs) methodology, we propose an automated searching neural net architectures strategy that can perform various tasks such as identify zero-day attacks. By automating the malicious intent detection process from the darknet, the advanced proposed solution is reducing the skills and effort barrier that prevents many organizations from effectively protecting their most critical assets.

Increasing distributed generation and intermittency, along with the increasing frequency of extreme weather events, impose a serious challenge for the electric power supply security. Understanding the costs of interruption is vital in terms of enhancing the power system infrastructure and planning the distribution grid. On the other hand, customer rights and demand response techniques are further reasons to study the worth of power reliability. In this paper, the authors make use of directional distance function and shadow pricing method for a case study from Finland. The aim is to calculate the cost of one minute of power interruption from the distribution network operator perspective. The sample consists of 78 distribution network operators from Finland with cost and network information between 2013 and 2015.

In this paper, we investigate an analytical solution of a class of nonlinear fractional integro-differential equation base on a generalized fractional power series expansion. The fractional derivatives are described in the conformable's type. The new approach is a modified form of the well-known Taylor series expansion. The illustrative examples are presented to demonstrate the accuracy and effectiveness of the proposed method

The energy transfer process of laser selective melting is very complex. To study the effect of la-ser selective melting on the microstructure and properties of 18Ni-300 martensitic steel, ABAQUS was used to simulate the temperature of laser cladding 18Ni-300 martensitic steel at different time points and different laser power. The results show that the cross-section shape of the molten pool changes from round to oval With the increase of laser power, the higher the peak value of temperature time curve, the greater the temperature gradient; and the laser clad-ding experiment of 18Ni-300 martensitic steel was carried out, and the microstructure and me-chanical properties of the samples under different laser power were analyzed. The results show that with the increase of laser power, the grain size of the cladding layer becomes smaller and the microstructure becomes more compact; the hardness of the side surface of the sample is higher than that of the upper surface, and the tensile strength and elongation show a trend of first increasing and then decreasing.

Researchers have focused on collaborative governance as an effective measure to realise sustainable natural resource management through the participation of various stakeholders. However, the literature has indicated that issues such as power imbalances tend to undermine the effectiveness of collaborative governance. Powerful actors represented by the government tend to control collaborative processes and produce benefits for dominant groups, while less empowered local communities are often deprived of opportunities for livelihood improvement. Although numerous researchers have analysed the key factors that influence the processes and outcomes of collaborative governance, few have identified a concrete measure to reduce the risk of failure, particularly when managing power imbalances in developing countries. This study explored a methodology to address the power imbalances in collaborative governance based on a case study of a participatory peatland fire prevention project implemented in West Kalimantan Province, Indonesia. Semi-structured interviews and questionnaire surveys conducted with project participants suggested that measures such as establishing a joint team of government officers and villagers, providing a common facilitation training programme, training villagers as facilitators, promoting equal knowledge sharing, and allowing villagers to make their own decisions mitigated the power imbalances between the two groups.

Ultrasonic imaging & NDE applications can greatly improve their signal-to-noise ratios (SNR) by driving each transducer (composing piezoelectric arrays) with a spike giving pulsed power of k-Watts, repetitively at a PRF = 5000 spikes/s, by using a HV capacitive-discharge generator. However very-high levels, of pulsed intensities (3-10 A) and voltages (300-700 V) must be considered for a rigorous spike modeling. Even though the consumed "average" power will be small, the intensity through each transducer achieves several amperes, so the pulsed powers delivered by each HV generator can attain levels higher than in CW high-power ultrasonic applications: e.g., up to 5 kW / spike. This is concluded here from a transient modeling of the loaded generator. Then, unforeseen phenomena rise: intense brief pulses of driving power & emitted force in transducers, and non-linearities in driver semiconductors, because their characteristic curves only include linear ranges. But fortunately, piezoelectric devices working in this intense regime do not show serious heating problems, because the average power remains being moderate. Intensity, power and voltage, driving a broadband transducer from a HV capacitive pulser, are calculated to drastically improve (in ≅ 40 dB) the ultrasonic net dynamic range available, with emitted forces ≅ 250 Newtons pp and E/R received pulses of 70 V pp.

Open Inertia Modelling (OpInMod) is a modelling framework designed to create unit commitment and economic inertia dispatch optimisation problems. Present energy system modelling generators do not consider power system inertia in unit commitment and economic dispatch modelling to assess future energy system pathways. However, maintaining sufficient power system inertia in power systems is the foundation for power frequency controllability. The work at hand describes the functionality and approaches of open source tool OpInMod. The softwares universal design approach increases reuse potential. OpInMod is distributed with a set of examples to test and understand OpInMod

A linear Cauchy problem with polynomial coefficients wich combines q-difference operators for q>1 and differential operators of irregular type is examined. A finite set of sectorial holomorphic solutions w.r.t the complex time is constructed by means of classical Laplace transforms. These functions share a common asymptotic expansion in the time variable which turns out to carry a double layers structure which couples q-Gevrey and Gevrey bounds. In the last part of the work, the problem of confluence of these solutions as q tends to 1 is investigated.

(1) Background: Due to the high proportion of disadvantaged students in a rural school in Taiwan and the gap between students’ concepts and practices of environmental protection and sustainable energy, four science and mathematics teachers in this school planned an engineering-centered PjBL of sustainable energy curriculum in a Makers Club to enhance students’ creativity, engineering skills, practices of environmental protection and sustainable energy, and learning attitudes; (2) Methods: This study is four-year action research. Teachers and students initiated the idea from rebuilding an old fan in a classroom; (3) Results: The students in the Makers Club improved their engineering skills and created various green-power generation devices (evolved from ventilation ball generator, hydropower, ocean current power generators to tiny, 3D-printing wind power generators). They turned environmental protection and sustainable energy concepts into actions during practices and won awards from science and engineering fairs every year. This creative and supportive atmosphere spread from the club to the whole school and improved the students’ practices of environmental protection and learning attitudes after long-term implementation; (4) Conclusions: The design principles of the engineering-centered PjBL of sustainable energy curriculum played a critical role and were outlined at the end of the study.

This research paper is part of the wider project concerning the very first detailed mapping of the overall Taiwanese hydro-power plants that took place from 2013 up to 2015 and it is currently in evaluation and finalization stage. The case of Shanping hydro-power plant has been carefully studied, photographed, documented and mapped in situ. It was one of the isolated hydro-power plant projects originally built to supply the remote area with the specific designation. Shanping hydro-power plant, as well as the other units from the early hydro-power generation era in Taiwan, are considered to be the technological heritage of civil and mechanical engineering that reflects later in all the further projects up to nowadays modern Taiwanese hydro-power plants. Unfortunately, most of the hydro-power houses from the older periods were severely damaged or destroyed by natural causes which were also the case of Shanping unit. The research is trying to reconstruct the original location of the powerhouse and its supporting structures based on available historical documents, previous studies, comparative methodology, and the current on-site observation.

Power system decentralization has been an emerging topic for the past decade in an effort to improve power quality and environment protection via increased integration of renewable energy sources. Towards these objectives, decentralized microgrids have been proposed and thoroughly investigated in terms of technical capabilities and economic performance. In fact, the planning and actual operation of small-scale, decentralized microgrids has started in countries such as Canada, Japan, USA, UK and other countries. It is expected that the research in this area will progress and eventually take over the existing paradigm of large-scale power generation in the future. These small-size decentralized microgrids could be connected with nearby microgrids under normal operating conditions, but under special events, such as natural or man-made disasters, they would be disconnected and run in islanded mode. Under such high impact – low probability events, the microgrid must have resiliency to successfully re-connect with other microgrids and the main grid. In this paper, an Energy Management System (EMS) for a microgrid having a resiliency function, allowing to operate under islanded mode after an accident, is proposed. The proposed tool, called Resilient Energy Management System (ResEMS), aims at procuring reserve power into the microgrid’s Battery Energy Storage System (BESS) effectively, by importing it from the nearby connected power system. The accident is assumed to be a predictable natural disaster, which means that the accident occurrence time, duration and level of damage can be estimated. The proposed ResEMS has been applied to a microgrid comprising of a BESS, a diesel generator and several photovoltaic devices. The simulation results verify its beneficial operation.

The increasing variability in power plant load, in response to a wildly uncertain electricity market and the need to to mitigate CO₂ emissions, lead power plant operators to explore advanced options for efficiency optimization. Model-based, system-scale dynamic simulation and optimization are useful tools in this effort, and the subject of the work presented here. In prior work, a dynamic model validated against steady-state data from a 605 MW subcritical power plant was presented. This power plant model is used as a test-bed for dynamic simulations, in which the coal load is regulated to satisfy a varying power demand. Plant-level control regulates plant load to match an anticipated trajectory of the power demand. The efficiency of the power plant operating at varying load is optimized through a supervisory control architecture that performs set point optimization on the regulatory controllers. Dynamic optimization problems are formulated to search for optimal time-varying input trajectories that satisfy operability and safety constraints during the transition between plant states. An improvement in time-averaged efficiency of up to 1.8% points is shown feasible with corresponding savings in coal consumption of 184.8 tons/day and carbon footprint decrease of 0.035 kg/kWh.

In light of the latest trends in global installed capacities, the importance of variable renewable energy sources (VRES) to future energy supply systems is evident. Despite this, the inherent intermittency of VRES remains an obstacle to their widespread adoption. Green hydrogen is often suggested as an energy carrier that can account for this in a sustainable manner. In the analysis, a robust European energy system in the context of 2050 and with 100% VRES energy supply is designed through an iterative minimal cost-optimization approach that ensures robust security of supply over 38 weather-year scenarios (1980-2017). The impact of spatial VRES variability is factored in by defining exclusive VRES groups within each optimization region and, from this, it can be seen that higher numbers of groups in each region offer cheap electricity generation locations to the optimizer and thus decrease the total annual cost of the system. Beyond this, the robust system design and impact of inter-annual variability is identified by iteratively combining the installed capacities of different system designs obtained by applying 38 historical weather years. The robust system design outlined here has significantly lower capacities in comparison to the maximum regional capacities obtained in the first round of optimization.

One of the most crucial and economically beneficial tasks for energy customer is peak load curtailment. On account of the fast response of renewable energy resources (RERs) such as photovoltaic (PV) units and battery energy storage system (BESS), this task is closer to be efficiently implemented. Depends on the customer peak load demand and energy characteristics, the feasibility of this strategy may warry. When adaptive neuro-fuzzy inference system (ANFIS) is exploited for forecasting, it can provide many benefits to address the above-mentioned issues and facilitate its easy implementation, with short calculating time and re-trainability. This paper introduces a data driven forecasting method based on fuzzy logic for optimized peak load reduction. First, the amount of energy generated by PV is forecasted using ANFIS which conducts output trend, and then, the BESS capacity is calculated according to the forecasted results. The trend of the load power is then decomposed in Cartesian plane into two parts, left and right from load peak, searching for BESS capacity equal. Network switching sequence over consumption is provided by a fuzzy logic controller (FLC) with respect to BESS capacity and PV energy output. Finally, to prove the effectiveness of the proposed ANFIS-based peak shaving method, offline digital time-domain simulations have been performed on a real-life practical test micro grid system in MATLAB/Simulink environment and the results have been experimentally verified by testing on a practical micro grid system with real-life data obtained from smart meter and also, compared with several previously-reported methods.

With the unceasing advancement in wide-bandgap (WBG) semiconductor technology, the minimal reverse-recovery charge Qrr and other more powerful natures of WBG transistors enable totem-pole bridgeless PFC to become a dominant solution for energy storage systems (ESS). This paper focuses on design and implementation of a control structure for a totem-pole boost PFC with newfangled enhancement-mode Gallium Nitride (eGaN) FETs, not only to simplify the control implementation, but also to achieve high power quality and efficiency. The converter is designed to convert a 90-264-VAC input to a 385-VDC output for a 2.6-kW output power. Lastly, to validate the methodology, an experimental prototype is characterized and fabricated. The uttermost efficiency at 230 VAC attains 99.14%. The lowest total harmonic distortion in the current (ITHD) at high line condition (230 V) reaches 1.52% while the power factor gains 0.9985.

The Brahmaputra is one of the largest rivers in the world, ranking fifth in average discharge. As a result, it is heavily braided with various intricate paths in order to dissipate its huge energy. Although this river is normally classed as a braided river, it has recently been classified as an anastomosing river due to its multi-channel features over alluvial plains. Additionally, the Brahmaputra river’s morphology is random in nature as a result of its high flow variability and bank erodibility. Its anastomosing planform changes in response to seasonal water and sediment waves, resulting in a morphology that is extremely complex. The purpose of this study is to examine the Brahmaputra river’s anastomosing planform entropy as a measure of complexity, power spectral density as a measure of fluctuation and their relationship to the energy expenditure as an imprint of flflow rate of river systems on alluvial landscapes.

We point out that field equations of general relativity are implied by a maximal force given by c⁴/4G, analogous to the way that special relativity is implied by a maximal speed given by c. We present some of the arguments for this equivalence. The maxi-mal force naturally plays the role of an elastic constant for space-time. Implications of the maximal force for gravitational wave measurements, cosmology and black holes are highlighted. Quantum aspects of the maximal force are discussed.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of simulation and statistical results of EO with other optimization techniques showed that EO is more effective and superior.

Intending to analyze the role of nuclear power in an integrated energy system, we used the IESA-Opt-N cost minimization model focusing on four key themes: system-wide impacts of nuclear power, uncertain technological costs, flexible generation, and cross-border electricity trade. We demonstrate that the Levelized Cost of Energy (LCOE) alone should not be used to demonstrate the economic feasibility of a power generation technology. For instance, under the default techno-economic assumptions, particularly the 5% discount rate and exogenous electricity trade potentials, it is cost-optimal for the Netherlands to invest in 9.6 GWe nuclear capacity by 2050. However, its LCOE is 34 €/MWh higher than offshore wind. Moreover, we found that nuclear power investments can reduce demand for variable renewable energy sources in the short term and higher energy independence (i.e., lower imports of natural gas, biomass, and electricity) in the long term. Furthermore, investing in nuclear power can reduce the mitigation costs of the Dutch energy system by 1.6% and 6.2% in 2040 and 2050, and 25% lower national CO₂ prices by 2050. However, this cost reduction is not significant given the odds of higher nuclear financing costs and longer construction times. In addition, this study has shown that lower financing costs (e.g., EU taxonomy support) considerably reduce the relevance of nuclear cost uncertainties on its investments. Furthermore, we demonstrate that the economic feasibility of national nuclear power investments can vary considerably depending on the cross-border electricity trade assumptions. Additionally, we found that lowering the cost of small modular reactors has more impact on their economic feasibility than increasing their generation flexibility. In conclusion, under the specific assumptions of this study, nuclear power can play a complementary role (in parallel to the wind and solar power) in supporting the Dutch energy transition from the sole techno-economic point of view.

Integrating large-scale wind energy in modern power systems is demanding more efficient mathematical models to properly address classical assumptions in power system problems. In particular, there are two main assumptions in power system problems with wind integration that have not been adequately studied yet; First, non-linear AC power flow equations have been linearized in most of the literature. Such simplifications can lead to inaccurate power flow calculations that may result in other technical issues. Second, wind power uncertainties are inevitable and have been mostly modelled using the traditional uncertainty modelling approaches, that may not be suitable for large-scale wind power integration. In this paper, we address both challenges: we present a tight second-order conic relaxation (SOCR) for optimal power flow (OPF) problem, and simultaneously, implement the new effective budget of uncertainty approach for uncertainty modelling that determines the maximum wind power admissibility first and then addresses the uncertainty in the model. To the best of our knowledge, this is the first study that proposes an effective robust second-order conic programming (ERSOCP) model that simultaneously addresses the issues of power flow linearization and wind power uncertainty with the new paradigm on the budget of uncertainty approach. Our numerical results show the merit of the proposed model against traditional linearized power flow equations as well as traditional uncertainty modelling approaches.

The aspirated hypersonic air-breathing propulsion system requires a large amount of power generation, but its special structure makes it impossible to adopt common power generation methods. The high-temperature gaseous hydrocarbon fuel thermal power generation (TPG) system was developed to solve the power generation problem for hypersonic air-breathing propulsion system. But off-design operating conditions of the hypersonic propulsion system results in a more complex process for both propulsion system and the TPG system. To better analyzing the dynamic thermos-physical characteristics of hypersonic airbreathing propulsion system considering thermal-mechanical coupling process among cooling/TPG system, a dynamic analytical model was developed, and the dynamic thermos-physical characteristics of TPG system under different off-design working conditions were conducted. It can be concluded from the analytical results that the dynamic process of thermos-physical characteristics shows a complex trend under the flight Mach number and fuel equivalence ratio off-design working conditions. Such complexity of dynamic characteristics brings difficulties in fuel supply for the propulsion system.

HybridAC/DC microgrids(HMG) are emerging as an attracting method for integrating the AC/DC distributed energy resources(DERs) with the features of high-performance and low-cost. In the isolated hybrid AC/DC microgrid (IHMG), the key problem is how to balance the power variation and regulate the voltage and frequency. Various energy storage systems (ESS)and interlinking converter (IC) technologies are viable for this application. The present study proposes a novel unified power flow model to evaluate and compare the abilities of the ESS with different connection topologies and ICs with different control approaches to maintain the voltage and frequency stability of the IHMG. In order to investigate the performance of the proposed scheme, five operation modes of the IHMG are defined and explained. The classification is based on the connection topologies and control modes of the ESS/IC in the IHMG. Then, a set of generic PF equations are derived. Moreover, three binary matrices are applied in the construction of the unified power equations. These matrices are used for describing the running state of the IHMG. Finally, in order to verify the proposed scheme, it is applied to several case studies of the IHMG. The operation characteristics of multi-DC subgrids IHMG in different modes, particularly when an external disturbance occurs, are investigated.

The central limit theorem (CLT) and its generalization to stable distributions have been widely described in literature. However, many variations of the theorem have been defined and often their applicability in practical situations is not straightforward. In particular, the applicability of the CLT is essential for a derivation of heterogeneous ensemble of Brownian particles (HEBP). Here, we analyze the role of the CLT within the HEBP approach in more detail and derive the conditions under which the existing theorems are valid.

Following a recent proof of Shannon's entropy power inequality (EPI), a comprehensive framework for deriving various EPIs for the Rényi entropy is presented that uses transport arguments from normal densities and a change of variable by rotation. Simple arguments are given to recover the previously known Rényi EPIs and derive new ones, by unifying a multiplicative form with constant c and a modification with exponent α of previous works. In particular, for log-concave densities, we obtain a simple transportation proof of a sharp varentropy bound.

In this paper, we derive and prove, by means of Binomial theorem and Faulhaber's formula, the following identity between $m$-order polynomials in $T$ $$\sum_{k=1}^{\ell}\sum_{j=0}^m A_{m,j}k^j(T-k)^j=\sum_{k=0}^{m}(-1)^{m-k}U_m(\ell,k)\cdot T^k=T^{2m+1}, \ \ell=T\in\mathbb{N}.$$

This contribution considers an improved control scheme for three-phase two-stage grid-tied photovoltaic (PV) power system based on integral sliding mode control (ISMC) theory. The proposed control scheme consists of maximum power point tracking (MPPT), DC-Link voltage regulation and grid currents synchronization. A modified voltage-oriented maximum power point tracking (VO-MPPT) method based on ISMC theory is proposed for design of an enhanced MPPT under irradiation changes. Moreover, a novel DC-Link voltage control based on ISMC theory is proposed in order to achieve good regulation of DC-Link voltage over its reference. To inject the generated PV power into the grid with high quality, a voltage oriented control based on space vector modulation (SVM) and ISMC (VOC-ISMC-SVM) has been developed to control the grid currents synchronization. Numerical simulations are performed in Matlab/SimulinkTM environment in order to evaluate the proposed control strategy. In comparison with conventional control scheme, the developed control strategy provides an accurate MPP tracking with less power oscillation as well as a fast and an accurate DC-Link regulation under climatic conditions variations. Moreover, the transfer of the extracted power into the grid is achieved with high quality.

Solar power innately has issues with weather, grid demand and time of day, which for the case of concentrating solar power (CSP) can be mitigated through use of thermal energy storage. Nuclear reactors, including lead-cooled fast reactors (LFRs), can load follow, but have high fixed and low operating costs which can make this economically unattractive. We investigate potential synergies through coupling CSP and LFR together in a single supercritical CO$_2$ Brayton cycle and/or using the same thermal energy storage. Combining these cycles allows for the LFR to thermally charge the salt storage in the CSP cycle during low demand periods to be dispatched when grid demand increases. The LFR/CSP coupling into one cycle is modeled to find the preferred location of the LFR heat exchanger, CSP heat exchanger, sCO$_2$-to-salt heat exchanger (C2S), turbines, and recuperators within the supercritical CO$_2$ Brayton cycle. Three cycle configurations have been studied: two-cycle configuration, which uses CSP and LFR heat for dedicated turbocompressors, has the highest efficiencies but with less component synergies; a combined cycle with CSP and LFR heat sources in parallel is the simplest with the lowest efficiencies; and a combined cycle with separate high temperature recuperators for both the CSP and LFR is a compromise between efficiency and component synergies. Additionally, four thermal energy storage charging techniques are studied: the turbine positioned before C2S, requiring a high LFR outlet temperature for viability; the turbine after the C2S, reducing turbine inlet temperature and therefore power; the turbine parallel to the C2S producing moderate efficiency; and a dedicated circulator loop. While all configurations have pros and cons, use of a single cycle offers component synergies with limited efficiency penalty. Using a turbine in parallel with the C2S heat exchanger is feasible but results in a low charging efficiency, while a dedicated circulator loop offers flexibility and near perfect heat storage efficiency but increasing cost with additional cycle components.

Combined systems for power production and thermally activated cooling have a high potential for improving the efficiency and utilisation of thermal systems. In this regard, various configurations have been proposed and are comprehensively reviewed. They are primarily based on absorption systems and the implementation of multiple levels of complexity and flexibility. The configuration of the absorption power and cooling combined cycle proposed herein has wide commercial applicability owing to its simplicity. The configuration of the components is not new. However, the utilisation of aqueous salt solutions, the comparison with ammonia chiller and with absorption power cycles, the focus on parameters that are important for real-life applications, and the comparison of the performances for constant heat input and waste heat recovery are novel. The proposed cycle is also compared with a system based on the organic Rankine cycle and vapour compression cycle. An investigation of its performance proves that the system is suitable for a given range of boundary conditions from a thermodynamic standpoint, as well as in terms of system complexity and technical feasibility. New possibilities with regard to added power production have the potential to improve the economics and promote the use of absorption chiller systems.

The induced draft (ID) fan is important auxiliary equipment in the thermal power plant. It is of great significance to monitor the operation of the ID fan for safe and efficient production. In this paper, an adaptive warning model is proposed to detect early faults of ID fans. First, a non-parametric monitoring model is constructed to describe the normal operation states with the multivariate state estimation technique (MSET). Then, an early warning approach is presented to identify abnormal behaviors based on the results of the MSET model. As the performance of the MSET model is heavily influenced by the normal operation data in the historic memory matrix, an adaptive strategy is proposed by using the samples with a high data quality index (DQI) to manage the memory matrix and update the model. The proposed method is applied to a 300 MW coal-fired power plant for early fault detection, and it is compared with the model without an update. Results show that the proposed method can detect the fault earlier and more accurately.

The overrun of transient power quality index caused by the large-capacity electric arc furnace (EAF) has become a prominent problem affecting the safe and stable operation of the power system. (1) In this paper, the relationship between arc furnace volt-age and current is derived based on the different stages of arc combustion, and the random variation of chaotic phenomenon of the arc voltage are simulated. Established an EAF model suitable for the study of transient power quality problems. (2) Take 50t AC EAF as an example to analyze the reactive power impact and the influence on the point of common coupling (PCC) voltage caused by the three-phase short circuit of the electrode. The results show that the experimental results are consistent with the theoretical analysis, verifying the correctness and effectiveness of the model. (3) When the three-phase short-circuit occurs, the reactive power impact is nearly 6 times that of normal operation, the short-circuit current is 2.66 times that of normal operation, and the effective value of the PCC voltage has dropped by 40.37%, which provides a theoretical basis for real-time compensation of impulsive reactive power and improvement of the transient power quality of the EAF.

Quantum cell automata (QCA) is a nanotechnology that uses a transistor-free structure to design digital circuits and overcome the limitations listed for CMOS circuits. The computing circuits that make up the bulk of computers can be designed and using this technology. Subtractors are a big part of computational circuits. This research deals with the design of a subtractor that due to the innovation in the design of this circuit and the novel arrangement of quantum cells of its kind has caused the number of cells used in the design of the circuit to reach its lowest value compared to previously designed circuits. The size of the circuit as well as the loss power are minimized compared to the circuits designed by the subtractors. Another trait clears of this circuit compared to many previous designs is its single-layer design, which reduces latency and noise in the output waveform. The circuit designed by the QCADesigner simulator is tested and simulated inadition the results are displayed in the simulated waveform. Also, the results of calculations for power dissipation in each QCA cell were evaluated by QCAPro software, which is a powerful tool for estimating power loss simulation. It has less implementation and level (single layer) than Previous designs.

We consider a control problem for a diffusive PDE model of heterogeneous population of thermostatically controlled loads (TCLs) aiming to balance the aggregate power consumption within a given amount of time. Using the Green’s function approach, the problem is formulated as an approximate controllability problem for a residue depending on control parameters nonlinearly. A sufficient condition for approximate controllability is derived in terms of initial temperature distribution, operation time of TCLs and threshold value of the aggregate power consumption. Case studies allow to reveal the advantages of the proposed solution from numerical calculations point of view.

The extrusion of food for human and animal consumption is a unit operation that includes mixing, shearing and force to the materials related to the rheological properties of the materials in the extruder. The present work aims to study the rheological behavior of an extruded fish diet incorporating hydrolyzed protein flour processed by extrusion. The measurement was carried out online with a slit die rheometer, defining the rheological models and parameters that fit the process. During the extrusion process, the raw materials used were hydrolyzed protein meal, fish meal and cassava starch. For the results, the evaluated treatments were adjusted to the Power Law, where an increase in the shear rate decreases the viscosity of the material, corresponding to a pseudoplastic behavior. The incorporation of hydrolyzed protein flour presented a significant effect on the value of n and Klp, increasing the viscosity with the increase in the percentage of inclusion of HPH. The models obtained for the prediction of the viscosity are adjusted to the changes in shear rate, temperature and humidity of the system.

In this paper we review dynamics and roughness of bonds in proteins on example of albumin, that is important from the physiological point of view. We have performed computer simulations of albumin chain. Statistics were collected by performing many simulations realizations for each experimental setting. We concentrate on hydrogen bonds, cation-π and π- π interactions and NP contacts. Histograms of hydrogen bonds length are positively skewed in contrary to histograms of interactions and HP contacts that are negatively skewed. Scaling exponents of power spectra of energies of bonds / interactions /contacts are in range -0.2 to -0.5 and significantly differ between various hydrogen bonds or interactions. Varying scaling of such spectra can be used to classify between distinct bonds or contacts. Concerning particular amino-acids, largest amount of HBO H20 bonds are between Glutamate (GLU) amino-acids and water particle, while large amount of HBO bonds are formed with Lysine (LYS). For HP contacts the mayor role plays Phenylalanine (PHE) and Leucine (LEU) amino-acids. From decay curves HBO H2O bonds decays in fastest rate, while HBO bonds and HP contacts at slowest rate. We present as well decay curves of bonds formed by particular amino-acids, that gives interesting results.

This paper proposes an approach to estimate the parameters of an AC-DC boost power factor corrector converter which includes an EMI filter. To this end, once the topology is known, measurements at the input and output terminals of the converter are done to identify the values of the passive elements. The proposed methodology is based on the trust-region nonlinear least squares algorithm to identify the parameters of the converter. The steady-state and the transient signals of the converter at the input/output terminals are acquired non-intrusively without any internal modification of the circuitry. The accuracy of the parameter identification carried out is determined by comparing the estimated values with the actual values provided by the manufacturer, and by contrasting the measured signals with the ones obtained with a simulation model with the estimated values of the parameters. The results presented in this paper prove the accuracy of the proposed approach, which can be extended to other power converters and filters.

Learning disorders (LD) are diagnosed in children whose academic skills of reading, writing or mathematics are impaired and lagged according to their age, schooling and intelligence. Children with LD experience substantial working memory (WM) deficits, even more pronounced if more than one of the academic skills is affected. We compared the task-related EEG power spectral density of children with LD (n= 23), with a control group of children with good academic achievement (n= 22), during the performance of a WM task. sLoreta was used to estimate the current distribution at the sources, and 18 brain regions of interests (ROIs) were chosen with an extended version of the eigenvector centrality mapping technique. In this way, we lessen some drawbacks of the traditional EEG at the sensor space by an analysis at the brain sources level over data-driven selected ROIs. Results: The LD group showed fewer correct responses at the WM task, an overall slower EEG with more theta activity in all ROIs, less upper-alpha power at posterior areas, and less high-frequency beta activity in frontal areas. We explain these EEG patterns in LD children as indices of an inefficient neural resource management related with a delay in the neural development.

The power-generation capacity of grid-connected photovoltaic (PV) power systems is increasing. As output power forecasting is required by electricity market participants and utility operators for the stable operation of power systems, several methods have been proposed using physical and statistical approaches for various time ranges. A short-term (30 min ahead) forecasting method has been previously proposed by our laboratory for geographically distributed PV systems using motion estimation. This study focuses on an important parameter for estimating the proposed motion and optimizing the parameter. This parameter is important because it is associated with the smoothness of the vector field, which is the result of motion estimation and influences the forecasting accuracy. In the periods with drastic power output changes, the evaluation was conducted on 101 PV systems located within a circle of 15-km radius in the Kanto region of Japan. The results indicate that the absolute mean error of the proposed method with the optimized parameter is 10.3%, whereas that of the persistent prediction method is 23.7%. Therefore, the proposed method is effective in forecasting for periods when PV output changes drastically in a short time.

Modern exchange theories model a large market, but do not explain single exchange. The paper considers the phenomenon of single exchange and formulates the general exchange problem in the form of a system of two equations, subjective and objective. Subjective equilibrium is given by the Walras-Jevons marginal utility equation. Objective equilibrium equations by Walras and Jevons are averaged over all transactions in the market and can only give a rough general picture without explaining the specific price of an individual exchange. An exchange micro-condition must be found that, when averaged, will give the Walras market equilibrium macro-condition. The study of the internal structure of exchange leads to the need to consider power. The concept of generalized power is introduced. It is generalized power that serves as the primary comparable and measurable objective basis of exchange. The power theory of exchange provides the objective price-equation. It is demonstrated that money is a measure of generalized power in exchange and a certification of generalized power in subsequent exchanges. The proposed theory is able to uniformly explain any exchange, including a single one, which is impossible with the existing theories of exchange.

Low-frequency audible noise generated by the magnetostriction effect inherent to the operation of power transformers has become a major drawback, especially in cases where the electrical substation is located in urban areas subject to strict environmental regulations that imposes sound pressure limits, differing for day and night periods. Such regulations apply a +5 dB penalty if a tonal component of noise is present, which is clearly the case of magnetostriction noise, typically concentrated at twice the industrial frequency (50 Hz or 60 Hz, depending on the country). The strategy used to eliminate the tonal characteristics, therefore contributing to establish compliance with the applicable regulation and to alleviate the discomfort it causes to the human ear, consisted in superimposing to the substation noise a masking sound synthesized from “sounds of nature” with suitable intensities, to flatten the noise spectrum while enhancing the soundscape. The masking system (heavy-duty speakers powered by a microprocessor platform) was validated at an already judicialized urban scenario. Measurement results confirmed that the masking solution was capable of flattening the tonal frequencies, whose beneficial effect yielded the cancellation of the public civil action filed by the neighbors. The proposed solution is ready to be replicated to other scenarios.

The microgrid is a small-scale, autonomous decentralized power plant with its own distributed generation, storage capacity and multiple loads, with the capacity to function in grid interconnected and an island mode. The decentralized control of microgrids with parallel operated voltage source converters (VSCs) is proposed in this paper to improve power quality using a machine learning approach. The DNN based MPPT controller is proposed and its best performance is presented. The SRF-PLL is utilized for AC side synchronization in VSC control. The proposed microgrid involves two PV arrays fed to two voltage source converters along with their independent controls, connected in parallel through LC filters and line coupling transformers and serves the loads at PCC. The proposed model is simulated using MATLAB/Simulink. The dq-framed inner loop control is employed to individually regulate the real and reactive power at the point of common coupling. Furthermore, the proposed model is analyzed and compared by employing a mathematical model of AC system dynamics, inner loop control, output voltage quality, AC harmonic spectrum analysis, and total harmonic distortion (THD) in both grid interconnected and island mode. In island mode, AC harmonic spectrum and THD are accomplished within the permissible range.

Molten salt reactors have gained substantial interest in the last years due to their flexibility and their potential for simplified closed fuel cycle operation for massive net-zero energy production. However, a zero-power reactor experiment will be an essential first step into the process delivering this technology. The choice of the optimal reflector material is one of the key issues for such experiments since on the one hand it offers huge cost saving potential due to reduced fuel demand, on the other hand an improper choice of the reflector material can have negative effects on the quality of the experiments. The choice of the reflector material is for the first time introduced through a literature review and a discussion of potential roles of the reflector. The 2D study of different potential reflector materials has delivered a first down selection with SS 304 as representative for stainless steel, lead, copper, graphite, and beryllium oxide. A deeper look identified in addition iron-based material with high Si content. The following evaluation of the power distribution has shown the strong influence of the moderating reflectors creating a massively disturbed power distribution with a peak at the core boundary. This effect has been confirmed through a deeper analysis of the 2D multi-group flux distribution which lead to the exclusion of the BeO and the graphite reflector. The most promising materials identified have been SS 304, lead, and copper. The final 3D Monte-Carlo study demonstrated that all three materials have the potential to reduce the required amount of fuel by up to 60% compared NaCl which has been used in previous studies and is now taken as reference A first cost analysis has identified the SS 304 reflector as the most attractive solution. The results of the 2D multi group deterministic study and the 3D multi group Monte-Carlo study have been confirmed through a continuous energy Monte-Carlo reference calculation showing only minor differences.

In this article, there's an effort to make sense about the new versions of matroid. I believe that there's new idea on the background of. matroid. Two styles of matroid is defined in the background of fixed graphs and after that the attributes of these new notion on the graph and its parameters have been studied. The focus of this article is on the version of matroid which has the basis on the cycles as if there's gentle discussion on the results which are based on the set of independent vertices as matroid-x. The relation amid fundamental parameters and specific set like independent set and minimal set in the terminology of graph theory have been considered. Matroid is the word to use in the study on the parameters of graph theory as if set theory and its terminology are also recorded. The terms of word in various terminology have been relatively used. There are open ways to use hypergraphs or some serious relations amid these two types.

There is a potential for synergy effects in utilizing CO2 for both enhanced gas recovery (EGR) and geothermal energy extraction (CO2-plume geothermal, CPG) from natural gas reservoirs. This “combined CO2-EGR–CPG system” has been introduced as a feasible approach that constitutes a CO2 Capture double-Utilization and Storage (CCUUS) system. In this study, we carry out reservoir simulations, using TOUGH2, to evaluate the sensitivity of the natural gas recovery, pressure buildup, and geothermal power generation performance of the combined system to various key reservoir and operational parameters. The reservoir parameters include horizontal permeability, permeability anisotropy, reservoir temperature, and pore-size-distribution index; while the operational parameters include wellbore diameter and ambient surface temperature. Using an example of a natural gas reservoir model, we also investigate the effects of different strategies of transitioning from the CO2-EGR stage to the CPG stage on the energy-recovery performance metrics and on the two-phase fluid-flow regime in the production well. The simulation results show that overlapping the CO2-EGR and CPG stages and having a relatively brief period of CO2 injection but no production (which we call the CO2-plume establishment stage) achieves the best overall energy (natural gas and geothermal) recovery performance. Permeability anisotropy and reservoir temperature are the parameters the natural gas recovery performance of the combined system is most sensitive to. The geothermal power generation performance is most sensitive to the reservoir temperature and the production wellbore diameter. The results of this study pave the way for future CPG-based geothermal power-generation optimization studies. For a CO2-EGR–CPG project, the results can be a guide regarding the required accuracy of the reservoir parameters during exploration and data acquisition.

The testing of high-dimensional normality has been an important issue and has been intensively studied in literatures, it depends on the Variance-Covariance matrix of the sample, numerous methods have been proposed to reduce the complex of the Variance-Covariance matrix. The principle component analysis(PCA) was widely used since it can project the high-dimensional data into lower dimensional orthogonal space, and the normality of the reduced data can be evaluated by Jarque-Bera(JB) statistic on each principle direction. We propose two combined statistics, the summation and the maximum of one-way JB statistics, upon the independency of each principle direction, to test the multivariate normality of data in high dimensions. The performance of the proposed methods is illustrated by the empirical power of the simulated data of normal data and non-normal data. Two real examples show the validity of our proposed methods.

This review reports the available technologies for the flexible utilization of biomass towards negative CO₂ emissions and addresses the possibility to couple biogas production plants with the electrical grid converting excess electrical energy into storable chemical molecules. This changed mind-set towards biomass utilization can lead readily to the implementation of negative CO₂ emission along the entire bioenergy supply chain without limiting the potential for Power-to-X applications. First, the technologies for direct conversion of waste and wood into gaseous energy carriers are screened, to highlight the potential for the production of renewable fuels. Second, the processes for the removal of CO₂ from biogenic gas streams are analysed in terms of technological performance, cost and further potential for the CO₂ recovered. These technologies are the key to pre-combustion CO₂ capture and negative emissions. Third, the possibility of coupling biomass conversion and synthetic fuels production is explored, providing an overview on the technical maturity of the various energy storage processes. The flexible use of biomass can be an essential part of the future CO₂-free energy systems, as it can directly provide energy carriers all around the year and also large quantities of climate-neutral carbon for the production of synthetic fuels with renewable energy. In turn, when no additional renewable electricity is available, the CO₂ by-product from biofuel synthesis can be used for the negative emissions. This opens the way to an efficient strategy for the seasonal storage of electrical energy, realizing a carbon-neutral energy system coupled with the development of carbon-negative energy strategy.

Power law relationships, which describe scaling relationships of data, are powerful information theoretic descriptive tools in many empirical contexts, including that of music. Zipf’s law (pink noise) describes the optimum case of a power law relation where observations are exactly inversely proportional to their rank. Descriptions that approximate a pink noise signature can be said to maximize the amount of information in a signal, and is thus suggestive of a richness of an understanding. This information density of pink noise signatures is not, however, necessarily a desirable quality for explanations in general, which, by definition, “flattens out” some data while highlighting others, ideally those most relevant to an interpretation. The privileging of data most relevant to comprehension corresponds to a red noise relationship, as opposed to the pink noise of Zipf’s law or the white noise of a description that highlights nothing in particular. Here, I explore and evaluate this concept of red noise explanations in the form of analyses of three comparable short piano works: Robert Schumann’s “Von fremden Ländern und Menschen” (no.1 from Kinderszenen op. 15, 1838), Frédéric Chopin’s Prelude op. 28 no. 20 (1838-9), and Felix Mendelssohn’s “Venetianisches Gondellied” (no. 6 from Lieder ohne Worte op. 19b, 1829-30).

This paper presents an alternative constraint handling approach within a specialized genetic algorithm (SGA) for the optimal reactive power dispatch (ORPD) problem. The ORPD is formulated as a nonlinear single-objective optimization problem aiming to minimize power losses while keeping network constraints. The proposed constraint handling approach is based on a product of sub-functions that represents permissible limits on system variables and that includes a specific goal on power loss reduction. The main advantage of this approach is the fact that it allows a straightforward verification of both feasibility and optimality. The SGA is examined and tested with the proposed constraint handling approach and the traditional penalization of deviations from feasible solutions. Several tests are run in the IEEE 30, 57, 118 and 300 bus test power systems. The results obtained with the proposed approach are compared to those offered by other metaheuristic techniques reported in the specialized literature. Simulation results indicate that the proposed genetic algorithm with the alternative constraint handling approach yields superior solutions when compared to other recently reported techniques.

The ubiquitous diffusion of Power Electronic Converters (PECs) in many fields of application including traction and energy conversion is suggesting the possibility of new and better integration of advanced power conversion and ICT services. This work investigates the possible advancements in the use of optical fibers for control of PECs, using Plastic Optical Fiber. The optical communication link connects the switching control to the converter control, following the line of separation between the expertises of the power electronic engineer and the control engineer. Control wise, the PEC becomes a black box compatible with any off-board controller, now immune from the Electromagnetic Interference (EMI) produced by the power switches. The redundant optical link is ready for the high switching (and sampling) frequencies possible with the use of SiC power semiconductor devices (100 kHz+). Distributed control of multiple PEC units and advanced telemetry for diagnostics and prognostics are targeted. A proof-of-concept demonstrator is presented and tested. Moreover, the possible evolution towards a power electronic cloud with remote management and orchestration is described.

The world is moving to the next phase of the energy transition with high penetrations of renewable energy. Flexible and scalable redox flow battery (RFB) technology is expected to play an important role in ensuring electricity network security and reliability. Continuous performance improvements will further enhance their value by reducing parasitic losses and maximizing available energy conversion over broader operating conditions. Concentration overpotentials from poor internal reactant distribution at high and low states of charge (SOC) limit power densities and are thus an important area of investigation. However, efforts to address these coupled electrochemical phenomena can compromise mechanical performance. Modelling and simulation of cell design innovations have shown it is possible to reduce losses from pump energy while increasing the availability of active species where required. The combination of wedge-shaped cells with static mixers investigated in this paper can reduce pressure drop and improve energy efficiency. Toroidal vanadium redox flow battery (VRB/VRFB) designs incorporating this innovation are presented for further development to improve community engagement with the technology.

This paper reports a new control strategy to improve sharing of unbalanced currents in islanded LV microgrids. This technique provides fast and effective sharing of positive-, negative- and zero-sequence currents, and is the first example of zero-sequence current sharing in the literature. The controllers are designed in the stationary frame. The control structure consists of four loops; 1)~the current controller; 2)~the voltage controller; 3)~the droop controller and the 4)~negative and zero sequence current controllers. The output current is considered unknown for the controller and is added to the control system as a disturbance. The proposed controller features a high gain in fundamental and harmonic frequencies, hence a good voltage quality is obtained in the presence of unbalanced and nonlinear loads. To this aim, a proportional-resonant (PR) controller is adopted as the current controller. By using a multi-resonant controller as current controller, a unified control structure is obtained which is suitable for both grid-connected and islanded modes. The voltage controller is designed using a resonant controller so that the voltage can have low VUF and THD in the presence of unbalanced and nonlinear loads. Furthermore, in this paper droop method is applied to the control structure to share real and reactive powers. Simulation studies show that the conventional droop method cannot share the oscillatory part of the output power that is due to the presence of unbalanced loads in the microgrid. This paper relies on using zero and negative sequence virtual impedance controller to share the oscillatory part of output power. By using zero-sequence virtual impedance controller (ZSVIC) and negative-sequence virtual impedance controller (NSVIC), the zero and negative sequence currents in the microgrid are controlled and shared effectively. By compensating zero- and negative-sequence currents locally, the flow of these currents in the microgrid is minimized, and the overall power quality of the islanded LV microgrid is improved.

Of all the renewable energy sources, solar photovoltaic (PV) power is estimated to be a popular source due to several advantages such as its free availability, absence of rotating parts, integration to building such as rooftops, and less maintenance cost. The nonlinear current-voltage (I–V) characteristics and power generated from a PV array primarily depend on solar insolation/irradiation and panel temperature. The extracted PV output power is influenced by the accuracy with which the nonlinear power–voltage (P–V) characteristic curve is traced by the maximum power point tracking (MPPT) controller. In this paper, a bio-inspired roach infestation optimization (RIO) algorithm is proposed to extract the maximum power from the PV system (PVS). To validate the usefulness of the RIO MPPT algorithm, MATLAB/Simulink simulations are performed under varying environmental conditions, for example, step changes in solar irradiance, and partial shading of the PV array. Furthermore, the search performance of the RIO algorithm is examined on different unconstrained benchmark functions, and it is that realized that the RIO algorithm has improved convergence characteristics in terms of finding the optimal solution than Particle swarm optimization (PSO). The results demonstrated that the RIO-based MPPT performs remarkably in tracking with high accuracy as the PSO-based MPPT.

Integrated photovoltaic-fuel cell (IPVFC) systems, amongst other integrated energy generation methodologies are renewable and clean energy technologies that have received diverse research and development attentions over the last few decades due to their potential applications in a hydrogen economy. This article systematically updates the state-of-the-art of IPVFC systems and provides critical insights into the research and development gaps needed to be filled/addressed to advance these systems towards full commercialisation. The design methodologies, renewable energy-based microgrid and off-grid applications, energy management strategies, optimisations and the prospects as self-sustaining power source were covered. IPVFC systems could play an important role in the upcoming hydrogen economy since they depend on solar hydrogen which has almost zero emissions during operation. Highlighted herein are the progresses as well as the technical challenges requiring research efforts to solve to realise numerous potential applications of IPVFC systems such as in unmanned aerial vehicles, hybrid electric vehicles, agricultural applications, telecommunications, desalination, synthesis of ammonia, boats, buildings, and distributed microgrid applications.

Harmonic resonances are part of the Power Quality (PQ) problems of electrified railways and have serious consequences for the continuity of service and integrity of components in terms of overvoltage stress. The interaction between Traction Power Stations (TPSs) and trains that causes line resonances is briefly reviewed showing the dependence on infrastructure conditions. The objective is real-time monitoring of resonance conditions seen first of all from the onboard panto-graph interface, but it is equally applicable at TPS terminals. Voltage and current spectra, and de-rived impedance and power spectra, are analyzed proposing compact and efficient methods based on Short-Time Fourier Transform, suitable for real-time implementation with the hardware avail-able for energy metering and harmonic interference monitoring. The methods are tested by sweeping long recordings taken at some European railways, covering cases of longer and shorter supply sections, with a range of resonance frequencies of about one decade. They give insight into the spectral behavior of resonances, their dependency on position and change over time, and criteria to recognize genuine infrastructure resonances from rolling stock emissions.

This study shows the application of self-organizing maps (SOMs) to probabilistic forecasts of wind power generation and ramps in Japan. SOMs are applied to atmospheric variables obtained from atmospheric reanalysis over the region, thus deriving classified weather patterns (WPs). Probabilistic relationships are established between the synoptic-scale atmospheric variables over East Japan and the generation of regionally integrated wind power in East Japan. Medium-range probabilistic wind power predictions are derived by SOM, as analog ensembles based on the WPs of the multi-center ensemble forecasts. As this analog approach handles stochastic uncertainties effectively, probabilistic wind power forecasts are rapidly generated from a very large number of forecast ensembles. The use of a multi-model ensemble provides better results than a one-forecast model. The hybrid ensemble forecasts further improve the probabilistic predictability skill of wind power generation, as compared with non-hybrid methods. It is expected that long-term wind forecasts will provide better guidance to transmission grid operators. The advantage of this method is that it can include an interpretative analysis of meteorological factors for variations in renewable energy.

Relying on the United Arab Emirates (UAE) extract from the cross-national data sample on the environmental affection and cognition of adolescent students, and seemingly unrelated bivariate weighted ordered probit regression modeling, this study adopts a national perspective to investigate the determinants of adolescent students' awareness and expectations about nuclear power technology and nuclear waste in the UAE. Identification of model parameters is achieved through maximum simulated likelihood estimation. The findings show that each level increase in UAE youth's interest in ecosystem services and sustainability raises their awareness of nuclear electrical power and nuclear waste by 13.5%, while reducing by 2.4% their level of optimism towards the technology. Furthermore, we find significant heterogeneity in youth awareness and expectations about nuclear power technology across the seven Emirates. Accounting for all other factors (including interest in ecosystem services), UAE youth awareness about nuclear electrical power technology appears to not significantly influence their expectations about the evolution of this technology for the next 20 years. Given that the UAE first nuclear power plant ``Barakah'' is scheduled to start operations end of 2019 beginning 2020, and the typical long life-span of nuclear wastes, our results provide important insights for developing sustainable nuclear energy policies and establishing a long-term nuclear energy program in the UAE.

A foundational model has been developed based on trends built from empirical data of space exploration and computing power through the first six plus decades of the Space Age which projects earliest possible launch dates for human-crewed missions from cis-lunar space to selected Solar System and interstellar destinations. The model uses computational power, expressed as transistors per microprocessor, as a key broadly limiting factor for deep space missions’ reach and complexity. The goal of this analysis is to provide a projected timeframe for humanity to become a multi-world species through off-world colonization, and in so doing all but guarantees the long-term survival of the human race from natural and human-caused calamities that could befall life on Earth. Be-ginning with the development and deployment of the first nuclear weapons near the end of World War II, humanity entered a ‘Window of Peril’ which will not be safely closed until robust off-world colonies become a reality. Our findings suggest the first human-crewed missions to land on Mars, selected Asteroid Belt objects, and selected moons of Jupiter and Saturn can occur before the end of the 21^st century. Launches of human-crewed interstellar missions to exoplanet destinations within roughly 40 lightyears of the Solar System are seen as possible during the 23^rd century and launch of intragalactic missions by the end of the 24^th century. An aggressive and sustained space exploration program, which includes colonization, is thus seen as critical to the long-term survival of the human race.

Abstract: Power generation using dielectric elastomer (DE) artificial muscle is attracting attention because of its light weight, low cost, and high efficiency. Since this method is a system that produces electricity without emitting carbon dioxide nor using rare earths, it would contribute to the goal of environmental sustainability. In this paper, the background of DEs, the associated high-efficient wave energy generation (WEG) systems that we developed using DEs, as well as the latest development of its material are summarized. By covering the challenges we face and the achievements that we’ve reached, we can discuss the opportunities to build the foundation of a recycled energy society through the usage of these WEGs. On the other hand, to make these possibilities commercially successful, the advantages of DEs need to be integrated with traditional technologies. To achieve this, we also consider the method of using DEs alone and a system used in combination with an oscillating water column. Finally, the current status and future of DEGs are discussed.

The goal of this paper is to present a low-cost, low-power prototype of a pulsed Ultra Wide Band UWB) oscillator and an UWB elliptical dipole antenna integrated on the same Radio Frequency (RF) Printed Circuit Board (PCB) and its digital control board for Real Time Locating System (RTLS) applications. The design is compatible with IEEE 802.15.4 high rate pulse repetition UWB standard being able to work between 6 GHz and 8.5 GHz with 500 MHz bandwidth and with a pulse duration of 2 ns. The UWB system has been designed using the CST Microwave Studio transient Electro-Magnetic (EM) circuit co-simulation method. This method integrates the functional circuit simulation together with the full wave (EM) simulation of the PCB’s 3D model allowing fast parameter tuning. The PCB has been manufactured and the entire system has been assembled and measured. Simulated and measured results are in excellent agreement with respect to the radiation performances as well as the power consumptions.

We examine a family of nonlinear q-difference-differential Cauchy problems obtained as a coupling of linear Cauchy problems containing dilation q-difference operators, recently investigated by the author, and quasi-linear Kowalevski type problems that involve contraction q-difference operators. We build up local holomorphic solutions to these problems. Two aspects of these solutions are explored. One facet deals with asymptotic expansions in the complex time variable for which a mixed type Gevrey and q-Gevrey structure is exhibited. The other feature concerns the problem of confluence of these solutions as q tends to 1.

Abstract. This article proposes new fuzzy controller to regulation the voltage, damp the oscillations and limit the overshoot behavior in single-machine infinite-bus power system. Two different independent MISO fuzzy controllers are designed. First controller, is voltage stabilizer and it composes of two adaptive fuzzy modules and proportional gain AVR. The voltage stabilizer is designed to regulate the terminal voltage, damp the voltage oscillation and limit the voltage overshoot to the industrial maximum allowable limit. The input signals of this stabilizer is are taken from the terminal voltage and the imposed voltage disturbance that can be read from any smart relay. The fuzzy output is used as feedback signal to control the AVR in order to achieve stabilized voltage equal to the reference voltage. The second fuzzy controller is designed with two input signals; “mechanical angle” and its derivative, and one output which is used as feedback signal to adapt the damping torque in order to damp the mechanical oscillation fast and with maximum overshoot not exceeding 10%, and hence damp the power angle oscillation that is important in the PSS improvement. MATLAB-SIMULINK was used for modelling and the test cases simulation. The results show very good performance for the proposed fuzzy controllers.

Energy transitions are reshaping the global energy system. Such shift has taken the power system to become a critical infrastructure for achieving economic development of every nation in the planet, therefore, guaranteeing its security is crucial, not only for energy purposes but as a part of a national security strategy. This paper presents a multi-dimensional index developed to assess energy security of electrical systems in the long term. This tool, named Power System Security Index (PSIx), and which has been previously used for the evaluation of a country in two different time frames, is applied to evaluate the member countries of the Latin American Energy Organization, located within the Latin America and the Caribbean region, in order to measure their performance on energy security. Mixed results were obtained from the analysis, with clear top performers in the region such as Argentina, while there are others with broad areas of opportunity, as it is the case of Haiti.

Purpose – Extend the Blade Element Momentum Theory (BEMT) such that rotors with pronounced cone and axis angle (tilt or yaw) can be calculated. Derive an equation for the speed ratio (lambda) as a function of Tip Speed Ratio (TSR), radius, blade, cone and axis angle. This converts the BEMT into an Unsteady BEMT or UBEMT. Present the Wagner rotor as one such rotor geometry. --- Methodology – Literature review and calculations. --- Findings – The UBEMT can be used to calculate highly unconventional rotor geometries. --- Research Limitations – Although the aerodynamic coefficients used in the UBEMT are from measurements in steady flow conditions, they can be used with success. --- Practical Implications – Also conventional Horizontal Axis Wind Turbines (HAWT) with noticeable cone and axis angle should be calculated with the UBEMT. The accuracy of power calculations of these HAWTs can be slightly improved. --- Originality – Analytic equations for rotors with cone and axis angle have barely been discussed.

This paper presents an optimal design for the inner current control loop of the continuous current conduction mode (CCM) power factor correction (PFC) stage, which it can be used as the front stage of the two stages alternating current-direct current (AC-DC) telecom power supply. Conventional single-phase CCM-PFC boost converter usually implemented with using of the proportional-integral (PI) controllers in both of the voltage and current control loops, to regulate the output DC voltage to the specified value, moreover to maintains the input current follows the input voltage which offers converter with high power factor (P.F) and low current total harmonic distortion (THD). However, due to the slow dynamic response of the PI controller at the zero-crossing point of the input supply current, input current can’t fully follow the input voltage which leads to high THD. Digitally controlled PFC converter with an optimal design of the inner current control loop using doubly control loops IP controller to reduce the THD and to offer input current with unity P.F was performed in this paper. Furthermore, for the economic design of the digitally control PFC converter, two isolated AC and DC voltage sensors are proposed and designed for the interfacing with the microcontroller unit (MCU). PSIM software was used to test the converter performance with using the proposed designed current controllers and isolated voltage sensors. High power density digitally controlled telecom PFC stage with P.F of about 99.93%, full load efficiency of about 98.70% and THD less 5.50% is achieved in this work.

Cognitive deterioration caused by illness or aging often occurs before symptoms arise, and their timely diagnosis is crucial to reducing its medical, personal, and societal impacts. Brain-Computer Interfaces (BCIs) stimulate and analyze key cerebral rhythms, enabling reliable cognitive assessment that can accelerate diagnosis. The BCI system presented analyzes Steady-State Visually Evoked Potentials (SSVEPs) elicited in subjects of varying age to detect cognitive aging, predict its magnitude, and identify its relationship with SSVEP features (band power and frequency detection accuracy), which were hypothesized to indicate cognitive decline due to aging. The BCI system was tested with subjects of varying age to assess its ability to detect aging-induced cognitive deterioration. Rectangular stimuli flickering at theta, alpha, and beta frequencies were presented to subjects, and frontal and occipital EEG responses were recorded. These were processed to calculate detection accuracy for each subject and calculate SSVEP band power. A neural network was trained using the features to predict cognitive age. The results showed potential cognitive deterioration through age-related variations in SSVEP features. Frequency detection accuracy declined after age group 20–40 and band power, throughout all age groups. SSVEPs generated at theta and alpha frequencies, especially 7.5 Hz, were the best indicators of cognitive deterioration. Here, frequency detection accuracy consistently declined after age group 20-40 from an average of 96.64% to 69.23%. The presented system can be used as an effective diagnosis tool for age related cognitive decline.

The differential gear train and speed regulating motor constitute the variable ratio transmission for grid-connected wind turbine with differential speed regulation. The synchronous generator in the system can accessing the power grid without frequency converter. The transmission can realize the mode of variable speed constant frequency that the wind rotor speed is varying and the generator rotor speed is constant. The power control method is studied under the different wind speed which is lower or higher than rated wind speed with using the relational expression of utilization rate of wind energy Cp, pitch angle β and the tip speed ratio λ. The SIMULINK software is used to build the 1500 kW wind turbine model with differential speed regulation. Some different wind speed is made as input. The feasibility of power control method for grid-connected wind turbine with differential speed regulation is verified by the comparison between the simulation results and the theoretical value of the key parameters.

The VLSI industry is facing parasitic effects that trouble development in the nanoscale domain. However, instead of replacing the traditional MOSFET design, it would be more advantageous to apply different doping profiles and discerning which deal with specific parasitic effects the best. With a review of Gaussian doping, Uniform doping, and Delta doping profiles and analysis of the FET technology characteristics that use these doping profiles, a comparison can be made among them for integrated circuit design engineers. These doping profiles are compared based on how well they perform against non-ideal and ideal environments. Also, both digital and analog performance are measured to ensure the uniqueness of each doping profile that is present. After getting a list of benefits from each doping profile, it is derived to determine which doping profile works best against a host of parasitic effects and what type of application do these doping profiles have

Molten salt reactors have gained substantial interest in the last years due to their flexibility and their potential for simplified closed fuel cycle operation for massive net-zero energy production. However, a zero-power reactor experiment will be an essential first step into the process of delivering this technology. The topic of the control and shut down for a zero power reactor is for the first time introduced through a literature review and the reduction of the control approaches to a limited number of basic functions with different variations. In the following, the requirements for the control and shutdown system for a reactor experiment are formulated, and based on these assessments, an approach for the shutdown – splitting the lower part of the core with reflector, and an approach for the control – a vertically movable radial reflector are proposed. Both systems will be usable for a zero-power system with a liquid as well as with as a solid core and even more importantly, both systems somehow work on the integral system level without disturbing the central part of the core which will be the essential area for the experimental measurements. Both approaches have been investigated as a singular system as well as their interactions with one another and the sensitivity of the control system. The study has demonstrated that both proposed systems are able to deliver the required characteristics with sufficient shutdown margin and a sufficiently wide control span. The interaction of the system has been shown to be manageable and the sensitivity is on a very good level. The multi-group Monte-Carlo approach has been cross evaluated by a continuous energy test leading to good results, but they also demonstrate that there is room for improvement.

This article introduces new method using ANN to control SVC in order to correct the source power factor of low voltage network. Two ANN approaches are investigated to design accurate and fast power factor correction (PFC) controller. First approach uses simple ANN (SANNA). Second approach uses cascaded ANN (CANNA). ANN regression, performance and the calculated error for both approaches are investigated to select between the two approaches. CANNA is selected as a better solution and it used to build the ANN PFFC controller using database, generated by MATLAB-Simulink, for standard three low voltage levels (240V, 220V and 110V). Nine test cases are carried out to validate the performance of proposed ANN PFC controller with a network has variable loads and low power factor (0.6 approximately). In order to extend the use of the controller to other voltage levels not included in the training process of the cascaded ANN, only the SVC is resized. Another nine cases are carried out with the same loads using the same ANN controller, as it is, to test its performance with the extended voltage level range (415V, 230V and 120V). The results show accurate and fast response in all test cases.

The power converter is the significant device in a wind power system. Wind turbine will be shut down and off grid immediately with the occurrence of the IGBT module open-circuit fault of power converter, which will seriously impact the stability of grid and even threaten personal safety. However, in the existing diagnosis strategies of power converter, there are few single and double IGBT modules open-circuit fault diagnosis methods producing negative results including erroneous judgment, omissive judgment and low accuracy. In this paper, a novel method to diagnose the single and double IGBT modules open-circuit faults of the permanent magnet synchronous generator (PMSG) wind turbine grid-side converter (GSC) is proposed. Above all, collecting the three-phase current varying with wind speed of 22 failure states including a normal state of PMSG wind turbine GSC as the original signal data. Afterward, the original signal data are decomposed by using variational mode decomposition (VMD) to obtain the mode coefficient series, which are analyzed by the proposed method base on fault trend feature for extracting the trend feature vectors. Finally, the trend feature vectors are used as the input of deep belief network (DBN) for decision-making and obtaining the classification results. The simulation and experimental results show that the proposed method can diagnose the single and double IGBT modules open-circuit faults of GSC, and the accuracy is higher than the benchmark models.

Large power transformers are generally associated with a maximum capacity rating of 100 MVA or higher. These large liquid dielectric power transformers are a custom-built piece of equipment, thus very expensive, and a backbone element of the power grid. In extreme cases as, for example, severe geomagnetic disturbances, permanently monitoring their condition will enhance their electrical reliability and resilience to guarantee efficient management of its life cycle. However, some traditional monitoring/diagnosis techniques have singular features when applied to large power transformers and their interlinked subsystems. In this context, and since that information is hardly put in evidence and compiled in the literature, this paper reviews the particularities of monitoring and diagnosing those assets.

Exploring the effect of the sample size on the estimation accuracy of airborne LiDAR forest attributes in a large-scale area can help in optimizing the technical application scheme of operational ALS-based large-scale forest stand inventories. In our study, sample datasets composed of different sample plots were constructed by repeated sampling from 1003 sample plots in a subtropical study area covering 2376 × 103 km2. Sixteen multiplicative power models were built in each forest type consisting of four forest attributes. Through these models, the variations of standard deviation (SD) and coefficient of variation (CV) of R2 and rRMSE of forest attribute estimation models for different quantity levels of sample plots were also analyzed. The results showed that, first, when the sample size increased from 30 to the top limit, the SD of the forest attributes and LiDAR variables showed a decreasing trend. Second, as the sample size increased, the rRMSE of the 16 forest attribute estimation models gradually decreased, while the R2 gradually increased. Third, when the sample size was small, both the SD of R2 and rRMSE of the models were large, and the SD of R2 and rRMSE gradually decreased as the sample size increased. In 50 models conducted for each attribute at the same sample size, for the mean standard deviations of forest attributes, the ten best performing models were lower than those of the total 50 models, and the worst ten models were the opposite. When the sample size increased, the accuracy of each forest attribute estimation model for each forest type gradually improved. The variation of forest attributes and the LiDAR variable of the construction model are critical factors that affect the model’s accuracy. To efficiently apply airborne LiDAR in order to survey large-scale subtropical forest resources, the sample size of the Chinese fir forest, pine forest, eucalyptus forest, and broad-leaved forest should be 110, 80, 85, and 70, respectively.

The goal of clustering is to identify common structures in a data set by forming groups of homogeneous objects. The observed characteristics of many economic time series motivated the development of classes of distributions that can accommodate properties such as heavy tails and skewness. Thanks to its flexibility, the Skewed Exponential Power Distribution (also called Skewed Generalized Error Distribution) ensures a unified and general framework for clustering possibly skewed and heavy tailed time series. This paper develops a clustering procedure of model-based type, assuming that the time series are generated by the same underlying probability distribution but with different parameters. Moreover, we propose to optimally combine the estimated parameters to form the clusters with an entropy weighing $k$-means approach. The usefulness of the proposal is showed by means of application to financial time series, demonstrating also how the obtained clusters can be used to form portfolio of stocks.

A quantitative description of the second law of thermodynamics in small scale systems and over short time scales comes from various fluctuation theorems. The applicability of the transient fluctuation theorem in particular to small scale systems perturbed from an initial equilibrium steady-state distribution has been demonstrated both theoretically and experimentally in several works over the past few decades. In addition, some experimental works in the past have also made successful attempts to demonstrate the applicability of the fluctuation theorem to small scale systems evolving from a certain nonequilibrium steady-state distribution over relatively long time scales. To this end, this paper seeks to demonstrate the transient fluctuation theorem for a Brownian particle confined within a power-law trapping potential by following the trajectory of the particle that itself is translating linearly along one dimension with constant acceleration in a viscous fluid. Considered herein is an idealized version of this model, in that it is assumed that the force of the trapping potential is only felt by the translating Brownian particle confined within the trap, and that this Brownian particle moves relative to the fluid molecules that are held stationary. The results presented herein show that the transient fluctuation theorem applies not only to equilibrium steady-state distributions but also to nonequilibrium steady-state distributions of an ideal colloidal system in an accelerated frame of reference in the asymptotic (long-time) limit.

Molten salt reactors have gained substantial interest in the last years due to their flexibility and their potential for simplified closed fuel cycle operation for massive net-zero energy production. The importance of a zero-power reactor for the process of developing a new, innovative rector concept like molten salt fast reactor is described here. It is based on historical developments as well as the current demand for experimental results and key factors that are relevant to the success of the next step in the development process of all innovative reactor types. In the systematic modelling & simulation of a zero-power molten salt reactor, the radius and the feedback effects are studied for a eutectic based system, while a heavy metal rich chloride-based system are studied depending on the uranium enrichment accompanied with the effects on neutron flux spectrum and spatial distribution. These results are used to support the relevant decision for the narrowing down of the configurations supported by considerations on cost and proliferation for the follow up 3D analysis to provide for the first time a systematic modelling & simulation approach for a new reactor physics experiment. The expected core volumes for these configurations have been studied using multi-group and continuous energy Monte-Carlo simulations identifying the 35% enriched systems as the most attractive and finally leading to the choice of the heavy metal rich compositions 35% enrichment as the reference system for future studies of the next steps in the zero power reactor investigation. The inter-comparison of the different applied codes and approaches available in the SCALE package has delivered a very good agreement between the results creating trust into the developed and used models and methods.

Colombia has one of the largest numbers of internally displaced populations in the world and recently entered a period of post-conflict. These socio-political processes and trends have increased the migration of people towards cities and accordingly are affecting the distribution and occurrence of tropical diseases in its urban and peri-urban areas. Studies have suggested that many human phenomena such as urbanization scale according to the size of human populations regardless of cultural context. But other studies show that health epidemics such as malarial and human immunodeficiency virus infections, follow a scale-free distribution in terms of population size and density. We explore these relationships and dynamics in a tropical context using statistical analyses and available geospatial data to identify the scale dynamics between urbanization processes and disease transmission in Colombia. We found that rural populations and certain disease dynamics were described by power-laws that are frequently mentioned in urbanization studies. However, we found that malaria presented higher intensity of infection in human settlements of less than 50,000 individuals, particularly for ethnic indigenous populations. Results indicate that epidemics and urbanization dynamics do indeed follow scales in Colombia; findings that differ from previous epidemiological studies such as those for malarial infection. Additionally, we identified trends showing that malarial infections become endemic in peri-urban areas. Targeting such peri-urban locations and certain demographic groups are key for managing public health issues in the urbanizing tropics.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

This study aims to determine the optimal configuration (position and operation duration) for wall mounted mechanical mixers based on the comparison of three-dimensional computational fluid dynamics (CFD) modelling results and physical data collected from the treatment plant. A three-dimensional model of anoxic zone 1, 2 and 3 of Northern Wastewater Treatment Plant (WWTP) located at Cairns Regional Council, Cairns, Queensland, Australia was developed and validated. The model was used to simulate the flow pattern of the WWTP and the simulation results are in good agreement with the physical data varying between 0% to 15% in key locations. The anoxic zones were subject to velocities less than the desired 0.3 metres per second however results for suspended solids concentration indicate that good mixing is being achieved. Results for suspended solids concentrations suggest that the anoxic zones are towards the upper limits recommended by literature for specific power dissipation. The duration for operation of mechanical mixers was investigated and identified that the duration could be reduced from 900 seconds down to 150 seconds. Alternative mixer positioning was also investigated and identified positioning which would increase the average flow velocity with decreased duration (150 seconds). The study identified that Council may achieve savings of $24,000 per year through optimisation of the mechanical mixers.

This work presents a control scheme to control the grid-connected single-phase photovoltaic (PV) system. The considered system has four 250W solar panels, a non-inverting buck-boost DC-DC converter, and DC-AC inverter with LCL filter. The control system aims to track and operate at the maximum power point (MPP) of PV panels, regulate the voltage of DC link, and supply the grid with a unity power factor. To well achieve these goals, the proposed control system consists of three parts, that are MPP tracking controller module with a fuzzy-based modified incremental conductance (INC) algorithm, a DC-link voltage regulator with a hybrid fuzzy proportional-integral (PI) controller, and a Current Controller module using the linear quadratic regulator (LQR) for grid-connected power. Based on fuzzy control and LQR, this work introduces a full control solution for grid-connected single-phase PV systems. The key novelty of this research is to analyze and prove that the newly proposed method is more successful in numerous aspects by comparing and evaluating the previous and present control methods. The designed control system settles quickly, which is critical for output stability. In addition, as compared to backstepping approach used in our past study, the LQR technique is more resistant to sudden changes and disturbances. Furthermore, backstepping method produces the larger overshoot, which has a detrimental impact on efficiency. Simulation findings under various weather conditions were compared to theoretical ones to indicate that the system can deal with variations in weather parameters.

Abstract: Currently, thermal power is the largest source of power in the world. Although the impacts of climate change on cooling water sufficiency in thermal power plants have been extensively assessed globally and regionally, their economic consequences have seldom been evaluated. In this study, the Asia-Pacific Integrated Model Computable General Equilibrium model (AIM/CGE) was used to evaluate the economic consequences of projected future cooling water insufficiency on a global basis, which was simulated using the H08 global hydrological model. This approach enabled us to investigate how the physical impacts of climate change on thermal power generation influence economic activities in regions and industrial sectors. To account for the uncertainty of climate change projections, five global climate models and two representative concentration pathways (RCPs 2.6 and 8.5) were used. The ensemble-mean results showed that the global gross domestic product (GDP) loss in 2070–2095 due to cooling water insufficiency in the thermal power sector was −0.21% (−0.12%) in RCP8.5 (RCP2.6). Among the five regions, the largest GDP loss of −0.57% (−0.27%) was observed in the Middle East and Africa. Medium-scale losses of −0.18% (−0.12%) and −0.14% (−0.12%) were found in OECD90 (the member countries of the Organization for Economic Co-operation and Development as of 1990) and Eastern Europe and the Former Soviet Union, respectively. The smallest losses of −0.05% (−0.06%) and −0.09% (−0.08%) were found in Latin America and Asia, respectively. The economic impact of cooling water insufficiency was non-negligible and should be considered as one of the threats induced by climate change.

This article presents a unique set of voltage and current data from a public building and acquired using a hybrid measurement solution that combines Python and Grafana. The transversal purpose consists of contributing to the community with a vision of the quality of the supply more oriented to the monitoring of the state of the network, providing a more realistic vision, which allows a better understanding, and the adoption of the best decisions to achieve the efficient energy management and thus optimize the operation and maintenance of power systems. The work focuses on higher order statistical estimators that, combined with exploratory data analysis techniques, improve the characterization of the shape of the stress signal. These techniques and data, together with the acquisition and monitoring system, present a unique combination in the line of low-cost measurement solutions. It also incorporates the underlying benefit of the contribution to industrial benchmarking. The paper also includes a computational comparison between Python and LabVIEW to elicit the performance of the measurement solution.

Partial shading on solar photovoltaic (PV) arrays is a prevalent problem in photovoltaic systems that impair the performance of PV modules and is responsible for reduced power output as compared to that in standard irradiance conditions thereby resulting in the appearance of multiple maximas on panel output power characteristics. These maxims contribute to mismatch power losses among PV modules. The mismatch losses depend on shading characteristics together with different interconnected configuration schemes of PV modules. The research presents a comparative analysis of partial shading effects on a 4 x4 PV array system connected in series(S), parallel (P), serries-parallel (SP),total-cross-tied (TCT),central-cross-tied(CCT),bridge-linked(BL),bridge-linked total cross-tied (BLTCT) ,honey-comb(HC), honey-comb total-cross-tied (HCTCT) and ladder (LD) configurations using MATLAB/Simulink. The PV module SPR-X20-250-BLK was used for modeling and simulation analysis. Each module is comprised of 72 number of PV cells and a combination of 16 PV modules was employed for the contextual analysis. Accurate mathematical modeling for the HCTCT configuration under partial shading conditions (PSCs) is provided for the first time and is verified from the simulation. The different configuration schemes were investigated under short-narrow,short-wide,long-narrow,long-wide, diagonal, entire row distribution, and entire column distribution partial shading condition patterns with mathematical implementation and simulation of passing clouds. The performance of array configurations is compared in terms of maximum power generated ), mismatch power loss (∆), relative power loss ) and the fill factor (FF). It was inferred that on average, TCT configuration yielded maximum power generation under all shading patterns among all PV modules interconnection configurations with minimum mismatch power losses followed by hybrid and conventional PV array configurations respectively.

In this study, the external magnetic field emitted by a wireless power transfer (WPT) system and the internal electric field induced into human body models during recharging operations of a compact electric vehicle (EV) are evaluated. To this aim an ad-hoc formulation for the source modeling is coupled with a commercial software that performs numerical dosimetry. Specifically, two realistic anatomical models both in a driving position and in a standing posture are considered, and the chassis of the EV is modeled either as a currently employed aluminum alloys and as a futuristic carbon fiber composite panel. Aligned and misaligned coil configurations of the WPT system are considered as well. The analysis of the obtained results shows that the ICNIRP reference levels are exceeded in the driving position, especially for the carbon fiber chassis, whereas no exceedance is observed in terms of basic restrictions, at least for the considered scenarios.