As the field of nanoscience is rapidly evolving, interest for novel, upgraded nanomaterials with combinatory features is also inevitably increasing. Hybrid composites, offer simple, budget-conscious and environmental-friendly solutions that can cater multiple needs at the same time and be applicable in many nanotechnology-related and interdisciplinary studies. The physicochemical idiocrasies of dendritic polymers have inspired their implementation as sorbents, active ingredient carriers and templates for complex composites. Ceramics are distinguished for their mechanical superiority and absorption potential that render them ideal substrates for separation and catalysis technologies. The integration of dendritic compounds to these inorganic hosts can be achieved through chemical attachment of the organic moiety onto functionalized surfaces, impregnation and absorption inside the pores, conventional sol-gel reactions or via biomimetic mediation of dendritic matrices, inducing the formation of usually spherical hybrid nanoparticles. Alternatively, dendritic polymers can propagate from ceramic scaffolds. All these variants are covered in detail. Optimization techniques as well as established and prospected applications are also presented.

In this study, the changes in mass, compressive strength and length were analyzed to investigate sulfate resistance according to ground granulated blast furnace slag (GGBFS) blending ratio and type of sulfate solution. All alkali activated mortars showed excellent sulfate resistance when immersed in sodium sulfate (Na₂SO₄) solution. However, when immersed in magnesium sulfate (MgSO₄) solution, different sulfate resistance results were obtained depending on the presence of GGBFS. Alkali activated GGBFS blended mortars showed a tendency to increase mass, increase length and decrease compressive strength when immersed in magnesium sulfate solution, but the alkali activated FA mortars did not show any significant difference depending on the types of sulfate solution. The deterioration of alkali activated GGBFS blended mortars in the immersion of magnesium sulfate solution was confirmed by the decomposition of C-S-H which is the reaction product by magnesium ion and the formation of gypsum (CaSO₄·2H₂O) and brucite (Mg(OH)₂).

Layered two-dimensional (2D) graphene oxide (GO) films are integrated with micro-ring resonators (MRRs) to experimentally demonstrate enhanced nonlinear optics in the form of four-wave mixing (FWM). Both uniformly coated and patterned GO films are integrated on CMOS-compatible doped silica MRRs using a large-area, transfer-free, layer-by-layer GO coating method together with photolithography and lift-off processes, yielding precise control of the film thickness, placement, and coating length. The high Kerr nonlinearity and low loss of the GO films combined with the strong light-matter interaction within the MRRs results in a significant improvement in the FWM efficiency in the hybrid MRRs. Detailed FWM measurements are performed at different pump powers and resonant wavelengths for the uniformly coated MRRs with 1−5 layers of GO as well as the patterned devices with 10−50 layers of GO. The experimental results show good agreement with theory, achieving up to ~7.6-dB enhancement in the FWM conversion efficiency (CE) for an MRR uniformly coated with 1 layer of GO and ~10.3-dB for a patterned device with 50 layers of GO. By fitting the measured CE as a function of pump power for devices with different numbers of GO layers, we also extract the dependence of GO’s third-order nonlinearity on layer number and pump power, revealing interesting physical insights about the evolution of the layered GO films from 2D monolayers to quasi bulk-like behavior. These results confirm the high nonlinear optical performance of integrated photonic resonators incorporated with 2D layered GO films.

Metal-organic framework (MOF) is a porous hybrid material of metal ions connected by organic bridging ligands. The coordination bonds link the metal ions, metal-ion clusters, and organic ligands to create the MOFs, and the materials are a distinctive class of crystalline frameworks. These porous materials possess relatively large surface area, tunable pore sizes, various functionalities, and high thermal stability. Therefore, diverse area of research including electrochemical sensor development utilizes distinctive and engineered MOFs materials. The review critically analyzes the strategy adopted for synthesizing a variety of MOFs materials. The role of these engineered materials in the fabrication of a miniaturized device demonstrates the detection of various emerging water contaminants in an aqueous medium. The studies demonstrated an understanding of the insights of sensor and device development. Moreover, the challenges encountered utilizing the MOFs in the electrochemical sensor development are precisely included, along with future perspectives of these studies.

This study aims to model grinding of a Polish slag and evaluate the particle size distributions of the products obtained after different grinding times. Then, selected products were alkali activated in order to investigate the effect of particle size on the compressive strength of the produced alkali activated materials (AAMs). Other parameters affecting alkali activation, i.e. temperature, curing and ageing time were also examined. Among the different mathematical models used to simulate the particle size distribution, Rosin-Rammler (RR) was found to be the most suitable. When piecewise regression analysis was applied to experimental data it was found that the particle size distribution of the slag products exhibits multi fractal character. In addition, grinding of slag exhibits non-first-order behavior and the reduction rate of each size is time dependent. The grinding rate and consequently the grinding efficiency increases when the particle size increases, but drops sharply near zero after prolonged grinding periods. Regarding alkali activation, it is deduced that among the parameters studied, particle size (and the respective specific surface area) of the raw slag product and curing temperature have the most noticeable impact on the compressive strength of the produced AAMs.

We introduce a number of techniques in quantitative convergent-beam electron diffraction under development by our group and discuss the basis for measuring interatomic electrostatic potentials (and therefore also electron densities), localised at sub-nanometre scales, with sufficient accuracy and precision to map chemical bonds in and around nanostructures in nanostructured materials. This has never before been possible as experimental measurements of bonding in quantum crystallography have hitherto always been restricted to homogeneous single-phased crystals.

This paper focused on impact localization of composite structures, which possess more complexity in the guided wave propagation because of the anisotropic behavior of composite materials. In this work, a composite plate was manufactured by using a compression molding process with proper pressure and temperature cycle. Eight layers of woven composite prepreg were used to manufacture the composite plate. A structural health monitoring (SHM) technique is implemented with piezoelectric wafer active sensors (PWAS) to detect and localize the impact on the plate. There are two types of impact event are considered in this paper (a) low energy impact event (b) high energy impact event. Two clusters of sensors recorded the guided acoustic waves generated from the impact. The acoustic signals are then analyzed using a wavelet transform based time-frequency analysis. The proposed SHM technique successfully detect and localize the impact event on the plate. The experimentally measured impact locations are compared with the actual impact locations. An immersion ultrasonic scanning method was used to visualize the composite plate before and after the impact event. A high frequency 10 MHz 1-inch focused transducer was used to scan the plate in the immersion tank. Scanning results show that there is no visible manufacturing damage in the composite plate. However, clear impact damage was observed after the high-energy impact event.

The purpose of this study is to investigate the different types of bricks as a construction material. In this study, monitoring different technical specification or characteristics of the bricks. At the end of study, Brick Quality Index (BQI) evaluated. According to BQI, bricks were classified poor to excellent quality.

In two-dimensional materials research, oxidation is usually considered as a common source for the degradation of electronic and optoelectronic devices or even device failure. However, in some cases a controlled oxidation can open the possibility to widely tune the band structure of 2D materials. In particular, we demonstrate the controlled oxidation of titanium trisulfide (TiS₃), a layered semiconductor that attracted much attention recently thanks to its quasi-1D electronic and optoelectronic properties and its direct bandgap of 1.1 eV. Heating TiS₃ in air above 300 °C gradually converts it into TiO₂, a semiconductor with a wide bandgap of 3.2 eV with applications in photo-electrochemistry and catalysis. In this work, we investigate the controlled thermal oxidation of individual TiS₃ nanoribbons and its influence on the optoelectronic properties of TiS₃-based photodetectors. We observe a step-wise change in the cut-off wavelength from its pristine value ~1000 nm to 450 nm after subjecting the TiS₃ devices to subsequent thermal treatment cycles. Ab-initio and many-body calculations confirm an increase of the bandgap of titanium oxysulfide (TiO_2-xS_x) when increasing the amount of oxygen and reducing the amount of sulfur.

Abstract: This review presents current literature on different nanocomposites coatings and surface finishing for different substrates (such as textiles, concrete, plastics, stones, metals and so on). In particular, this study is focused on smart materials, drug delivery systems, and industrial, antifouling and nano/ultrafiltration membrane coatings. Each of these nanostructured coatings shows interesting properties for different fields of application. In this review, particular attention is paid to the synthesis and the consequent physico-chemical characteristics of each coating and, therefore, to the different parameters that influence the substrate deposition process. Several techniques used in the characterization of these surface finishing coatings are also described. In this review, the sol-gel and polymerization method for preparing stimuli-responsive coatings as smart sensor materials is described; functional polymers and nanoparticles sensitive to pH, temperature, phase, light and biomolecules are also treated. Finally, nanomaterials based on phosphorus, borates, hydroxy carbonates and silicones are used and described as flame retardant coatings; organic/inorganic hybrid sol-gel coatings for industrial applications are illustrated, together with functional nanofiller (carbon nanotubes, metallic oxides, etc.) and polymers employed for nano/ultrafiltration membrane and antifouling coatings. In the last decades, several research institutes and industries have collaborated for the advancement of nanotechnology by optimizing conversion processes of conventional materials into coatings with new functionalities for intelligent, innovative, eco-sustainable and advanced applications.

Composite materials are widely used in the dental field in clinics as biomaterials. For example, it has been used as a biomaterial to repair caries and restore masticatory function, and as a cement to adhere the restoration to the tooth substrate. In order to demonstrate its function, dental biomaterials are measured their mechanical strength. From such basic research, we explained the potential of dental biomaterials, especially flexural strength and modulus of elasticity. Mechanical properties of dental biomaterials similar to those of the tooth, thermal stimulation, and aesthetic elements in the oral cavity. In this part, we will introduce the commercialized products of composites suitable for the characteristics and tooth quality, and provide the reader with the characteristics from the flexural characteristics of the composite materials used in clinical dentistry. In clinical performance, it might be advisable to delay polishing when composite biomaterials are used for luting materials, filling materials and core build-up materials since improved the flexural strength and the flexural modulus of elasticity were displayed after 1-day storage. And it is thought that flexural strength or characteristics is a significant important mechanical property of oral biomaterials.

This paper presents a physical and mathematical model that has been developed in the framework of the approach used in the computational mechanics of materials. The model is designed to enable the study of the patterns of deformation and fracture of ceramic composites with a transformation-hardened matrix that are obtained by additive technologies at the mesoscopic and macroscopic levels under intense dynamic loading. The influence of the loading rate on the formation of the fracture and energy dissipation fronts for composite materials, based on the Al2O3 20%ZrO2 system, is shown. Nonlinear effects under intense dynamic loading in the considered composites are associated with the processes of self-organization of structural fragments at the mesoscopic level, as well as the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

Road markings play an important role in road safety because they provide significant information to drivers about the road. For that reason, they must be replaced when they are not correctly perceived by road users. To analyse which are the main factors that affect road marking perception over time, a test section was designed in a two-lane rural highway, running actual traffic over 18 different types of markings fabricated with different combinations of drop-on materials. Chromatic coordinates, luminance and retroreflectivity of each sample were measured during 18 months in order to study their evolution over time. The results obtained show different behaviours depending on the aggregates and application method used. An increment of the durability has been observed with the use of different layers and mixtures of glass microbeads with different sizes.

A novel effective vibrational mode was discovered in the conventional transducer with an array of orthogonal (square) regular piezoelectric rods in 1-3 piezocomposite, containing the damping backing and front matching layers. The operational resonance in the structure was determined as the Surface Acoustic Wave (SAW) on the backing boundary excited by the adjacent piezo-rods, with its frequency typically near 3 times lower the fundamental half-lambda conventional piezocomposite resonance. Pulse-echo sensitivity and transmitting sound-pressure-level (SPL) in air showed that the signal strength is roughly comparable to the industrial similar air transducers at the frequency range 100…700 kHz, where at these frequencies the lateral and longitudinal piezoelement dimensions in the conventional transducer design are typically close to each other causing interference with unwanted coupling modes. As was determined theoretically and proved in experiments, the backing SAW resonance effect in the transducer performance is inherent just to the regular periodic 1-3 piezocomposite structure, and does occur neither with randomly located/oriented piezo-rods, nor in the homogeneous piezo-plate at least with the same lateral cross-section as the connected to it backing. The purpose of the article is to investigate a newly discovered operational vibrational mode of a SAW type in 1-3 regular piezocomposite, other than piezoelectric resonance. The investigated phenomena can improve the transceiver sensitivity, bandwidth, providing lower drive voltage, and smaller and lighter weight ultrasonic transducers. Based on the piezocomposites with thickness’ 1…1.5 mm (rod resonance near 2…3 MHz), pillar width 0.2…0.8 mm, kerf width 0.1…0.4 mm, the transceivers with an operating frequency from 140 kHz to 650 kHz were designed and fabricated with a conventional backing of a mixture of high-density tungsten powder and epoxy, and a matching layer of a mixture of low-density glass bubbles and epoxy. Experimental evaluation of their acoustical performance showed expected characteristics suitable for practical applications.

Mathematical literacy is a very hot issue in the development of mathematics learning, apart from mathematical literacy, another interesting thing is the entrepreneurial spirit that must be given from an early age, especially for vocational students. This research was conducted at SMK Rosma Karawang in the Department of Computer and Network Engineering, West Java Province with the XI grade students. The teaching materials developed by applying the principles of the development model developed with the ADDIE model consist of analysis, design, development, implementation and evaluation. This research and development model is considered suitable for developing teaching tools and materials which is used for the purposes of the learning process. Based on the results of data analysis and processing that have been carried out in this study, the development of teaching materials using the ADDIE model has met the appropriate and valid criteria by media, language and media expert valuators. Another result of developing this teaching material besides meeting the eligibility criteria is that the teaching materials developed are able to increase mathematical literacy and instill entrepreneurial spirit for students.

The interlaminar shear behavior of a [±45°] laminated carbon fiber reinforced plastic (CFRP) specimen was investigated utilizing microscale strain mapping in a wide field of view. A three-point bending device was developed under a laser scanning microscope, and the full-field strain distributions including normal, shear and principal strains of CFRP in a three-point bending test were measured using a developed sampling Moire technique. The microscale shear strain concentrations at interfaces between each two adjacent layers were successfully detected and found to be positive-negative alternately distributed before damage occurrence. The 45° layers slipped to the right relative to the -45° layers, visualized from the revised Moire phases and shear strain distributions of the angle-ply CFRP under different loads. The absolute values of the shear strain at interfaces gradually rose with the increase of the bending load, and the sudden decrease of the shear strain peak value implied the occurrence of interlaminar damage. The evolution of the shear strain concentrations is useful in the quantitative evaluation of the potential interlaminar shear failure.

Now-a-days, the thrust area of materials’ research is to develop multifunctional materials, which have multiple properties in a single functional material. We are interested to develop multifunctional polysilanes having special functional properties such as optical activity and photoluminescence (PL) properties. In this investigation, poly(methyl phenyl silane) (PMPS) was integrated with a chiral unit and a photoactive unit by in situ photopolymerization of (R)-N-(1-phenyl ethyl) methacrylamide (R-NPEMAM) and disperse red 1 methacrylate (DR1MA) monomer in the presence of PMPS. PMPS acted as a macrophotoinitiator and by UV exposure it produced macroradicals which initiated polymerization of chiral and photoactive monomers. Thus a block copolymer of PMPS-b-(R-NPEMAM-ran-DR1MA) was synthesized.The synthesized multifunctional organic inorganic hybrid polymer samples were characterized by FTIR and NMR spectroscopy. The molecular weights of the samples were measured by GPC analysis. The optical, chiroptical and photoluminescence properties were studied. The narrow band at about 1638 cm^-1 is due to C=O stretching vibration of -CONH- of the chiral unit. A wide absorption peaks at 3444 cm^-1 is the characteristic of NH trans stretching vibration of secondary amide group. The asymmetric stretching of NO₂ group appeared at 1481 cm^-1 and the characteristic peak at 1427 cm^-1 was observed due to azo (-N=N-) group stretching of DR1MA unit. The Si-Si band of PMPS appeared at about 462 cm^-1 in FTIR spectra. The optical absorbance observed at 272 nm is due to π-π* transition of aromatic ring and at 330 nm corresponds to σ-σ* transition of Si-Si bond. The other electronic absorption observed in the visible region at 475 nm corresponds to the combined contribution of n-π* and π-π* transition of DR1MA unit. The photoluminescence properties of such polymers were studied for the variation of concentration of the polymer solution and variation with excitation energy such as 275 nm, 325 nm and 475 nm in THF solvent. Such synthesized multifunctional photoactive organic-inorganic polymers having unusual optical, chiroptical and photoluminescence property may find novel optoelectronic (friend foe identification and secretive code identification) applications.

Demand for niobium and tantalum is increasing exponentially as these are essential ingredients for the manufacture of, among others, capacitors in technological devices and ferroniobium. Mine tailings rich in such elements could constitute an important source of Nb and Ta in the future and so alleviate potential supply risks. This paper evaluates the possibility of recovering niobium and tantalum from the slags generated during the tin beneficiation process of mine tailings from the old Penouta mine, located in Spain. To do so, a simulation of the processes that would be required to beneficiate and refine both elements is carried out. After tin carbothermic reduction, the slags are sent to a hydrometallurgical process where at the end niobium oxide and tantalum oxide are obtained. Reagents, water and energy consumption, in addition to emissions, effluents and product yields are assessed. Certain factors were identified as critical, and recirculation was encouraged in the model to maximize production and minimize reagents use and wastes. With this simulation, considering 3000 production hours per year, the metal output from the tailings of the old mine could cover around 1% and 7.4% of the world annual Nb and Ta demand, respectively.

With compact footprint, low energy consumption, high scalability, and mass producibility, chip-scale integrated devices are an indispensable part of modern technological change and development. Recent advances in two-dimensional (2D) layered materials with their unique structures and distinctive properties have motivated their on-chip integration, yielding a variety of functional devices with superior performance and new features. To realize integrated devices incorporating 2D materials, it requires a diverse range of device fabrication techniques, which are of fundamental importance to achieve good performance and high reproducibility. This paper reviews the state-of-art fabrication techniques for the on-chip integration of 2D materials. First, an overview of the material properties and on-chip applications of 2D materials is provided. Second, different approaches used for integrating 2D materials on chips are comprehensively reviewed, which are categorized into material synthesis, on-chip transfer, film patterning, and property tuning / modification. Third, the methods for integrating 2D van der Waals heterostructures are also discussed and summarized. Finally, the current challenges and future perspectives are highlighted.

In horses, there is an increasing interest in developing long-lasting drug formulations, with bi-opolymers as viable carrier alternatives in addition to their use as scaffolds, suture threads, screws, pins, and plates for orthopedic surgeries. This communication focuses on the prolonged biocompatibility and biodegradation of PLA, prepared by hot pressing at 180 ºC. Six samples were implanted subcutaneously on the lateral surface of the neck of one horse. The polymers remained implanted for 24 to 57 weeks. Physical examination, plasma fibrinogen, and the mechanical noci-ceptive threshold (MNT) were performed. After 24, 28, 34, 38, and 57 weeks, the materials were removed for histochemical analysis using hematoxylin-eosin and scanning electron microscopy (SEM). There were no essential clinical changes. MNT decreased after the implantation procedure, returning to normal after 48h. A foreign body response was observed by histopathologic evalua-tion up to 38 weeks. At 57 weeks, no polymer or fibrotic capsules were identified. SEM showed surface roughness suggesting a biodegradation process, with an increase in the average pore di-ameter. As in the histopathological evaluation, it was not possible to detect the polymer 57 weeks after implantation. PLA showed biocompatible degradation and these findings may contribute to future research in the biomedical area.

We improved a magnetic scanning microscope for measuring the magnetic properties of minerals in thin sections of geological samples at submillimeter scales. The microscope is comprised of a 200 µm diameter Hall sensor that is 142 µm from the sample; an electromagnet capable of applying to the sample up to 500 mT dc magnetic fields over a 40 mm diameter region; a second Hall sensor arranged in a gradiometric configuration to cancel the background signal applied by the electromagnet and reduce overall noise in the system; a custom-designed electronics to bias the sensors and provide adjustment for background signal cancelation; and a scanning XY stage with micrometer resolution. Our system achieves a spatial resolution of 220 µm with noise at 6.0 Hz of »300 nT_rms/(Hz)^1/2 in an unshielded environment. The magnetic moment sensitivity is 1.3 × 10⁻¹¹ Am².^1/2 We successfully measured the representative magnetization of a geological sample using an alternative model that takes into account the sample geometry and identified different micrometric characteristics in the sample slice.

Scattering of elastic waves in heterogeneous media has become one of the most important problems in the field of wave propagation due to its broad applications in seismology, natural resource exploration, ultrasonic nondestructive evaluation and biomedical ultrasound. Nevertheless, it is one of the most challenging problems because of the complicated medium inhomogeneity and the complexity of the elastodynamic equations. A widely accepted model for the propagation and scattering of elastic waves, which properly incorporates the multiple scattering phenomenon and the statistical information of the inhomogeneities is still missing. In this work, the author developed a multiple scattering model for heterogeneous elastic continua with strong property fluctuation and obtained the exact solution to the dispersion equation under the first-order smoothing approximation. The model establishes an accurate quantitative relation between the microstructural properties and the coherent wave propagation parameters and can be used for characterization or inversion of microstructures. Starting from the elastodynamic differential equations, a system of integral equation for the Green functions of the heterogeneous medium was developed by using Green’s functions of a homogeneous reference medium. After properly eliminating the singularity of the Green tensor and introducing a new set of renormalized field variables, the original integral equation is reformulated into a system of renormalized integral equations. Dyson’s equation and its first-order smoothing approximation, describing the ensemble averaged response of the heterogeneous system, are then derived with the aid of Feynman’s diagram technique. The dispersion equations for the longitudinal and transverse coherent waves are then obtained by applying Fourier transform to the Dyson equation. The exact solution to the dispersion equations are obtained numerically. To validate the new model, the results for weak-property-fluctuation materials are compared to the predictions given by an improved weak-fluctuation multiple scattering theory. It is shown that the new model is capable of giving a more robust and accurate prediction of the dispersion behavior of weak-property-fluctuation materials. Numerical results further show that the new model is still able to provide accurate results for strong-property-fluctuation materials while the weak-fluctuation model is completely failed. As applications of the new model, dispersion and attenuation curves for coherent waves in the Earth’s lithosphere, the porous and two-phase alloys, and human cortical bone are calculated. Detailed analysis shows the model can capture the major dispersion and attenuation characteristics, such as the longitudinal and transverse wave Q-factors and their ratios, existence of two propagation modes, anomalous negative dispersion, nonlinear attenuation-frequency relation, and even the disappearance of coherent waves. Additionally, it helps gain new insights into a series of longstanding problems, such as the dominant mechanism of seismic attenuation and the existence of the Mohorovičić discontinuity. This work provides a general and accurate theoretical framework for quantitative characterization of microstructures in a broad spectrum of heterogeneous materials and it is anticipated to have vital applications in seismology, ultrasonic nondestructive evaluation and biomedical ultrasound.

Layered two-dimensional (2D) GO films are integrated with silicon-on-insulator (SOI) nanowire waveguides to experimentally demonstrate an enhanced Kerr nonlinearity, observed through self-phase modulation (SPM). The GO films are integrated with SOI nanowires using a large-area, transfer-free, layer-by-layer coating method that yields precise control of the film thickness. The film placement and coating length are controlled by opening windows in the silica cladding of the SOI nanowires. Owing to the strong mode overlap between the SOI nanowires and the highly nonlinear GO films, the Kerr nonlinearity of the hybrid waveguides is significantly enhanced. Detailed SPM measurements using picosecond optical pulses show significant spectral broadening enhancement for SOI nanowires coated with 2.2-mm-long films of 1−3 layers of GO, and 0.4-mm-long films with 5−20 layers of GO. By fitting the experimental results with theory, the dependence of GO’s n₂ on layer number and pulse energy is obtained, showing interesting physical insights and trends of the layered GO films from 2D monolayers to quasi bulk-like behavior. Finally, we show that by coating SOI nanowires with GO films the effective nonlinear parameter of SOI nanowires is increased 16 fold, with the effective nonlinear figure of merit (FOM) increasing by about 20 times to FOM > 5. These results reveal the strong potential of using layered GO films to improve the Kerr nonlinear optical performance of silicon photonic devices.

Quasicrystals are a class of ordered solids made of typical metallic atoms but they do not exhibit the physical properties usually signaling the presence of metallic bonding and their electrical and thermal transport properties resemble a more semiconductor-like than metallic character. In this paper I first review a number of experimental results and numerical simulations suggesting that the origin of the unusual properties of these compounds can be traced back to two main features. For one thing, we have the formation of covalent bonds among certain atoms grouped into clusters at a local scale. Thus, the nature of chemical bonding among certain constituent atoms should play a significant role in the onset of non-metallic physical properties of quasicrystals bearing transition-metal elements. On the other hand, the self-similar symmetry of the underlying structure gives rise to the presence of an extended chemical bonding network due to a hierarchical nesting of clusters. This novel structural design leads to the existence of quite diverse wave functions, whose transmission characteristics range from extended to almost localized ones. Finally, the potential of quasicrystals as thermoelectric materials is discussed on the basis of their specific transport properties.

A new generation of nano-technologies is expanding solid propulsion capabilities and increasing their relevance for versatile and manoeuvrable micro-satellites with safe high-performance propulsion. We propose the innovative concept, connected with application of new synergistic effect of the energetic materials performance enhancement and reaction zones programming for the next generation small satellite multimode solid propulsion system. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon, by the properties of the energetic materials reaction zones and by localization of the energy release areas. This synergistic effect can be provided through application of the functionalized carbon-based nanostructured metamaterials as a nano-additives along with simultaneous manipulating by their properties through the electrostatic field. Mentioned effect will be controlled through predictive programming both by the spatial structure and physics-chemical properties of the functionalized carbon-based nano-additives and through the electromagnetic control of the self-organized wave pattern excitation and micro- and nano- scale oscillatory networks in the energetic material reaction zones. Suggested new concept makes it possible to increase the energetic material regression rate and increase the thrust of the solid propulsion system with minimal additional energy consumption.

The effect of transition metal substitution for Fe and the structural and magnetic properties of Gd2Fe16Ga0.5TM0.5 (TM=Cr, Mn, Co, Ni, Cu, and Zn) compounds were investigated. Rietveld analysis of X-ray diffraction indicates that all the samples crystallize in the hexagonal Th2Ni17 structure. The lattice parameters: a, c and unit cell volume show TM ionic radii dependence. Both Ga and TM atoms show preferred site occupancy for 12j and 12k sites. The saturation magnetization at maximum room temperature was observed for Co, Ni, and Cu of 69, 73, and 77 emu/g, respectively while minimum value was observed for Zn (62emu/g) doping Gd2Fe16Ga0.5TM0.5. Highest Curie temperature of 590 K was observed for Cu doping which is 15% and 5% and thesehigher than Gd2Fe17 and Gd2Fe16Ga compounds, respectively. The hyperfine parameters viz. hyperfine field and isomer shift, show systematic dependence on the TM atomic number. The observed magnetic and Curie temperature behavior in Gd2Fe16Ga0.5TM0.5 is explained on the basis of Fe(3d)-TM(3d) hybridization. The superior Curie temperature and magnetization value of Co, Ni, and Cu doped Gd2Fe16Ga0.5TM0.5 compounds as compared to pure Gd2Fe17 or Gd2Fe16Ga makes Gd2Fe16Ga0.5TM0.5 a potential candidate for high-temperature industrial magnet applications.

Graphene-based composites have been widely explored for electrode and electrocatalyst materials for electrochemical energy systems. In this paper, a novel composite material of the reduced graphene oxide nanosheets (rGON) with gold nanoparticles (NPs) (rGON-AuNP) is synthesized, and its morphology, structure and composition are characterized by SEM, HRTEM, XRD, EDX, FTIR, Raman, and UV-Vis techniques. To confirm this material’s electrochemical activity, a glucose oxidase (GOD) is chosen as the target reagent to modify the rGON-AuNP layer to form GOD/rGON-AuNP/glassy carbon (GC) electrode. Two pairs of distinguishable redox peaks, corresponding to the redox processes of two different conformational GOD on AuNP, are observed on the cyclic voltammograms of GOD/rGON-AuNP/GC electrode. Both cyclic voltammetry and electrochemical impedance spectroscopy are employed to study the mechanism of direct electron transfer from GOD to GC electrode on the rGON-AuNP layer. In addition, this GOD/rGON-AuNP/GC electrode shows catalytic activity toward glucose oxidation reaction.

An inter- and transdisciplinary concept has been developed, focusing on the scaling of industrial circular construction using innovative compacted mineral mixtures (CMM) derived from various soil types (sand, silt, clay) and recycled mineral waste. The concept aims to accelerate the systemic transformation of the construction industry towards carbon neutrality by promoting the large-scale adoption and automation of CMM-based construction materials, which incorporate natural mineral components and recycled aggregates or industrial by-products. In close collaboration with international and domestic stakeholders in the construction sector, the concept explores the integration of various CMM-based construction methods for producing wall elements in conventional building construction. Leveraging a digital urban mining platform, the concept aims to standardize the production process and enable mass-scale production. The ultimate goal is to fully harness the potential of automated CMM-based wall elements as a fast, competitive, emission-free, and recyclable alternative to traditional masonry and concrete construction techniques. To achieve this objective, the concept draws upon the latest advances in soil mechanics, rheology, and automation and incorporates open-source digital platform technologies to enhance data accessibility, processing, and knowledge acquisition. This will bolster confidence in CMM-based technologies and facilitate their widespread adoption. The extraordinary transfer potential of this approach necessitates both basic and applied research. As such, the proposed transformative, inter- and transdisciplinary concept will be conducted and synthesized using a comprehensive, holistic, and transfer-oriented methodology.

The use of high strength to weight ratio laminated composites is emerging in marine industry and applications as a very efficient solution for improving productivity. Nevertheless, delamination between the layers is a limiting factor for the wider application of laminated composites, as it reduces the stiffness and strengths of the structure. Interleaving nanofibrous mats between layers of composite laminates has been proved to be an effective method for improving composites delamination resistance. This paper aims to characterize the effect of interleaved nanofiber on mode I interlaminar properties and failure mechanisms when subjected to static and fatigue loadings. For this purpose, virgin and nanomodified woven laminates were subjected to Double Cantilever Beam (DCB) specimens. Static and fatigue tests were performed and the tests were monitored by acoustic emission technique. The mechanical results showed a 130% increase of delamination toughness for nanomodified specimens in the static loadings and more crack growth resistance in the fatigue loading. The AE results revealed that different type of failure mechanisms was the cause of these improvements for the modified specimens compared with the virgin ones.

In this article, the effect of substitution of Zr and Ga in Dy2Fe17 prepared by arc melting technique are studied. The substitution of Zr and Ga in Dy2Fe17 was found to have an important effect on their structure and magnetic properties. The Rietveld analysis conformed that the crystalline system wereTh2Ni17 structure. Lattice parameters a (Å) and c (Å), unit cell volume (Å3), bonding distance (Å) were calculated by using Rietveld analysis. The unit cell volume of Dy2Fe17-xZrx and Dy2Fe16Ga1-xZrx increase linearly with the Zr and Ga substitution. The substitution of Zr and Ga are limited up to x=1 in order to avoid the decrease in saturation magnetization. The Curie temperature (Tc) of Dy2Fe17-xZrx and Dy2Fe16Ga1-xZrx are found to be Zr content dependent. The Curie temperature is found to be increasing first and then decrease for higher Zr content. The maximum curie temperature was observed 510K at x = 0.75 for Dy2Fe17-xZrx and 505.1 K at x = 0.5 for Dy2Fe17-xZrx which are102 K and 97 K higher than Dy2Fe17. The room temperature Mössbauer analysis shows the decrease in average hyperfine field and increase in isomer shift with Zr doping.

The results of the bibliographic analysis show that the most explored nanomaterials in dentistry are graphene and carbon nanotubes, and their derivatives. A detailed analysis and a comparative study on their applications show that, although they are quite similar, graphene based materials seem to be more promising for most of the applications of interest in dentistry. The bibliographic study also demonstrated the potential of zeolite based materials, although the low number of studies on their applications shows that they have not been totally explored, as well as other porous nanomaterials that found important applications in medicine, such as metal organic frameworks, have not been explored. Subsequently, it is expected that the research effort will concentrate in graphene and zeolite based materials in the incoming years. Thus, present review paper presents a detailed bibliographic study, with more than 200 references, in order to describe briefly the main achievements that have been described in dentistry using nanomaterials, compare and analyze them in a critical way, with the aim of predicting the future challenges.

Sensing Technology (ST) plays a key role in Structural Health Monitoring (SHM) systems. ST focuses on developing sensors, sensory systems or smart materials that monitor a wide variety of materials properties aiming to create smart structures and smart materials, using Embedded Sensors (ESs), and allowing continuous and permanent measurements of the structural integrity. The integration of ESs is limited to the processing technology to embed the sensor due to its high-temperature sensitivity and the possibility of damage during its insertion into the structure. In addition, the technological process selection is dependent on the base material composition, either metallic or composite parts. The selection of smart sensors or the technology underlying them is fundamental to the monitoring mode. This paper presents a critical review of the fundaments and applications of sensing technologies for SHM employing ESs, focusing on the actual developments and innovation of these, as well as analysing the challenges that these technologies present, to build a path that allows a connected world through distributed measurement systems.

The space shuttle, a revolutionary spacecraft that has played a significant role in human space exploration, was composed of various advanced materials that were carefully selected to meet the extreme demands of spaceflight. This review paper provides a comprehensive examination of the materials historically employed in the construction of space shuttles and explores the latest trends shaping the field. The evolution of space shuttle materials is traced from the inception of the space program to contemporary missions, highlighting key milestones, challenges, and breakthroughs. Emphasis is placed on the critical role that materials play in the overall performance, safety, and sustainability of space shuttles. The paper begins by elucidating the diverse requirements that materials must fulfill in the harsh and complex environment of space, encompassing extreme temperatures, radiation exposure, and mechanical stresses. A detailed analysis of the materials utilized in the fabrication of various shuttle components, such as thermal protection systems, structural elements, and propulsion systems, is presented. Special attention is given to the challenges posed by re-entry and the strategies employed to mitigate heat-related issues. Furthermore, the review explores recent innovations and emerging materials that are reshaping the landscape of space shuttle design. Advancements in nanotechnology, composite materials, and additive manufacturing are discussed in the context of their potential applications for enhancing shuttle performance and reducing mission costs. The paper also addresses the importance of sustainability in space exploration, exploring materials with lower environmental impact and improved recyclability. The review concludes with a forward-looking perspective on the future of materials, considering ongoing research, development, and the potential incorporation of cutting-edge technologies. Insights are provided into how the evolving landscape of materials science may influence the design and manufacturing processes of the next generation of space vehicles. This paper provides an overview of the materials used in the construction of the space shuttle, including their properties, applications, and challenges. The materials used in the space shuttle are critical in ensuring the safety, performance, and longevity of the spacecraft, and understanding their characteristics and performance in space is crucial for the advancement of aerospace engineering.

The authors of this paper use an original method of diatomaceous earth fractionation, which allows for obtaining a filler with a specific particle size distribution. The method makes it possible to separate small, disintegrated and broken diatom frustules from those which maintained their original form in diatomaceous earth. The study covers a range of tests conducted to prove that such a separated diatomic fraction shows features different from the base diatomite used as an epoxy resin filler. We have examined mechanical properties of a series of diatomite/resin composites considering the weight fraction of diatoms and the parameters of the composite production process. The studied composites of Epidian 601 epoxy resin cross-linked with amine-based curing agent Z-1 contained 0 to 70% vol. of diatoms or diatomaceous earth. Samples were produced by casting into silicone moulds in vacuum degassing conditions and, alternatively, without degassing. The results have shown that the size and morphology of the filler based on diatomaceous earth affects mechanical and rheological properties of systems based on epoxy resin.

Steel reinforcement in concrete has the tendency to corrode and this process can lead to structural damage. FRP reinforcement represents a viable alternative for structures exposed to aggressive environments and has many possible applications where superior corrosion resistance properties are required. The use of FRP rebars as internal reinforcements for concrete, however, is limited to specific structural elements and does not yet extend to the whole structure. The reasons for this relate to the limited availability of curved or shaped reinforcing elements on the market and their reduced structural performance. Various studies, in fact, have shown that the mechanical performance of bent portions of composite bars is reduced significantly under a multiaxial combination of stresses and that the tensile strength can be as low as 25% of the maximum tensile strength that can be developed in the straight part. In a significant number of cases, the current design recommendations for concrete structures reinforced with FRP, however, were found to overestimate the bend capacity of FRP rebar. This paper presents the state-of-the art review of the research works on the strength degradation in curved FRP composites and highlighted the performance of exiting predictive models for the bend capacity of FRP reinforcement. Recent practical predictive model based on the Tsai-Hill failure criteria by considering the material at marcromechanical level is also discussed and highlighted. The review also identifies the challenges and highlights the future directions of research to explore the use of shaped FRP composites in civil engineering applications and the trends for future research in this area.

Immunoglobulin G (IgG), a type of antibody, represents approximately 75% of serum antibodies in humans, and is the most common type of antibody found in blood circulation Consequently, the development of simple, fast and reliable systems for IgG detection are of considerable interest which can be achieved using electrochemical sandwich-type immunosensors. In this study we have developed an immunosensor sub-strate using an inexpensive and very simple fabrication method based on ZnO nanorods obtained through the electrodeposition of ZnO. The ZnO nanorods were treated by electrodepositing a layer of reduced gra-phene oxide to ensure an easy immobilization of the antibodies. On this substrate, the sandwich configura-tion of the immunosensor was built through different incubation steps, that were all optimized. The im-munosensor is electrochemically active thanks to the presence of gold nanoparticles tagging the secondary antibody, therefore it has been used to measure the current density of the hydrogen development reaction which is indirectly linked to the concentration of H-IgG antigens. In this way the calibration curve was constructed obtaining a linear range of 1-100 ng / ml with a detection limit of few ng / mL and good sensi-tivity.

We show how the excitonic features of biaxial MoS₂ flakes are very sensitive to biaxial strain. We find a lower bound for the gauge factors of the A exciton and B exciton of (-41 ± 2) meV/% and (-45 ± 2) meV/% respectively, which are larger than those found for single-layer MoS₂. Interestingly, the interlayer exciton feature also shifts upon biaxial strain but with a gauge factor that is systematically larger than that found for the A exciton, (-48 ± 4) meV/%. We attribute this larger gauge factor for the interlayer exciton to the strain tunable van der Waals interaction due to the Poisson effect (the interlayer distance changes upon biaxial strain).

MPC (Magneto-Photonic Crystal) Optimisation is a feature-rich Windows software application designed to enable researchers to analyze the optical and magneto-optical spectral properties of multilayers containing gyrotropic constituents. A set of computational algorithms aimed at enabling the design optimization and optical or magneto-optical (MO) spectral analysis of 1D magnetic photonic crystals (MPC) is reported, together with its Windows software implementation. Relevant material property datasets (e.g., the optical spectra of refractive index, absorption, and gyration) of several important optical and MO materials are included, enabling easy reproduction of the previously published results from the field of MPC-based Faraday rotator development, and an effective demonstration-quality introduction of future users to the multiple features of this package. We also report on the methods and algorithms used to obtain the absorption coefficient spectral dispersion datasets for new materials, for which the film thickness, transmission spectrum, and refractive index dispersion function are known.

Techniques of stripping voltammetry (SV) determination of silver and gold in pyrites and carbonaceous matter were developed. The problem of quantitative transfer of the sample into the solution was solved. For this purpose, the ore matrix of carbonaceous shales was decomposed by mineral acids in autoclaves at high pressures. The element to be determined from the sample matrix was separated by extraction. Ag(I) ions from the solutions were extracted in the form of dithizonate complex in CCl₄. Au(III) ions were extracted by diethyl ether. The extracts were decomposed thermally. The dry residue was dissolved in the background electrolyte, and the element was determined by the SV method. The graphite electrode (GE) impregnated with polyethylene was used as a working electrode in SV–determination of silver. SV–determination of gold was carried out using GE modified by bismuth. The limits of detection (LOD) of Ag(I) and Au(III) contents were equal to 0.016 mg L^-1 and 0.0086 mg L^-1, respectively. The results of SV-determination of gold and silver in standard samples, pyrites and carbonaceous shales were presented. The silver content in the pyrite was 13.6 g t^-1, in carbon shale—0.34 g t^-1. The concentration of gold in the pyrite ore zone "Kirovsko–Kryklinskaya" was 1.15 g t^-1; in carbonaceous shales—2.66 g t^-1. The obtained data were consistent with the data of atomic emission spectroscopy (AES) and inductively coupled plasma mass spectrometry (ICP—MS). The error of determination of elements by stripping voltammetry was calculated when determining the silver content of 10...6 g t^-1 in pyrite and carbonaceous material, which was less than 12%, and when determining the gold content of 1...3 g t^{- 1} in pyrite and carbonaceous matter, which was less than 23%.

This study examines whether gas is emitted from the materials used in the fabrication of metal vacuum panels or not and if emitted, their degree as time goes by. As experimental materials, metal sheets, foamed concrete as a core material, and polymer materials as a sealing material between metal sheets were selected. Experiments on the type and the degree of bending of metal materials showed that aluminum’s vacuum reaching time of 0.001 torr was at least 40 sec to 90 sec in its flat plate, but its vacuum reaching time increased from 3 times to 4.5 times in case of 90 ° and 135 ° bending state. For this reason, it is judged that stainless steel or steel material is suitable because aluminum is inadequate in terms of processability at the time of fabricating the metal vacuum panel. Also, vacuum arrival times and weight changes with increasing foam content of inorganic foamed concrete increased from 22,000 sec to 42,000 sec with increasing foaming rate and also, the weight change increased from 1.7% to 8%. Also, the experimental results on the type of honeycomb materials, the PE (polyethylene) with a vacuum reaching time of 30,000 sec and with a weight change of 0.5% and the PTFE (Poly-tetrafluoro ethylene) with a vacuum reaching time of 29,000 sec and with a weight change of 2.2% showed the optimum value.

Pure orbital blowout fractures occur within the confines of the internal orbital wall. Restoration of orbital form and volume is paramount to prevent functional and esthetic impairment. The anatomical peculiarity of the orbit has encouraged surgeons to develop implants with customized features to restore its architecture. This has resulted in worldwide clinical demand for patient-specific implants (PSIs) designed to fit precisely in the patient's unique anatomy. Fused filament fabrication (FFF) three-dimensional (3D) printing technology has enabled the fabrication of implant-grade polymers such as Polyetheretherketone (PEEK), paving the way for a more sophisticated generation of biomaterials. This study evaluates the FFF 3D printed PEEK orbital mesh customized implants with a metric considering the relevant design, biomechanical, and morphological parameters. The performance of the implants is studied as a function of varying thicknesses and porous design constructs through a finite element (FE) based computational model and a decision matrix based statistical approach. The maximum stress values achieved in our results predict the high durability of the implants, and the maximum deformation values were under one-tenth of a millimeter (mm) domain in all the implant profile configurations. The circular patterned implant (0.9 mm) had the best performance score. The study demonstrates that compounding multi-design computational analysis with 3D printing can be beneficial for the optimal restoration of the orbital floor.

Integrated photonic devices operating via optical nonlinearities offer a powerful solution for all-optical information processing, yielding processing speeds that are well beyond that of electronic processing as well as providing the added benefits of compact footprint, high stability, high scalability, and small power consumption. The increasing demand for high-performance nonlinear integrated photonic devices has facilitated the hybrid integration of novel materials to address the limitations of existing integrated photonic platforms, such as strong nonlinear optical absorption or an inadequate optical nonlinearity. Recently, graphene oxide (GO), with its large optical nonlinearity, high flexibility in altering its properties, and facile fabrication processes, has attracted significant attention, enabling many hybrid nonlinear integrated photonic devices with improved performance and novel capabilities. This paper reviews the applications of GO to nonlinear integrated photonics. First, an overview of GO’s optical properties and the fabrication technologies needed for its on-chip integration is provided. Next, the state-of-the-art GO nonlinear integrated photonic devices are reviewed, together with comparisons of the nonlinear optical performance of different integrated platforms incorporating GO. Finally, the challenges and perspectives of this field are discussed.

In this research, Cellulose Nanofibers (NFC) modified with a eutectic of lauric acid (LA) was prepared as a new form-stable phase change material (NFC-LA). Thermal properties of this composite were investigated by Differential Scanning Calorimetry (DSC). The results revealed that the melting temperature and latent heat of NFC/LA were 21.56 °C and 88.5 J/g, respectively; and the super cooling degree for the NFC-LA composite decreased to 13.99 °C when compared to 20.28 °C of the pure lauric acid. Natural clay was purified and modified with Cetyltrimethyl ammonium bromide (CTAB) to prepare organoclay. Through FTIR spectra, we have confirmed that the clay was successfully modified. The PCM-composite was then added to the organoclay to obtain a new composite denoted NFC-LA-OC. this latter was added to cement and was investigated as a reinforcement material in cement mortars for thermal energy storage application. The prepared material can both solve the leakage problem associated to the phase change material, and reduce or even avoid the use of heating and air conditioning systems, which are energy-intensive systems, and therefore reduce energy consumption.

Tissue engineering, also called “regenerative medicine”, refers to attempt to create functional human tissue from cells in laboratory. This is a field that uses living cells, biocompatible materials, suitable biochemical and physical factors and their combinations, to create tissue-like structures.. To date, no tissue engineered skeletal muscle implants have been developed for clinical use, but it may represent a valid alternative to treat volumetric muscle loss in the near future. Herein, we reviewed the literature and showed different techniques to produce synthetic tissues with the same architectural, structural and functional properties of native tissues.

The emergence of various electronic devices and equipment such as electric vehicles and drones requires higher energy density energy storage devices. Lithium-sulfur batteries (LSBs) are considered as the most promising new generation energy storage system owing to high theoretical specific capacity and energy density. However, the severe shuttle behaviors of soluble lithium polysulfides (LiPSs) and the slow redox kinetics lead to low sulfur utilization and poor cycling stability, which seriously hinder the commercial application of LSBs. Therefore, various catalytic materials have been employed to solve these troublesome problems. High entropy materials (HEMs), as advanced materials, can provide unique surface and electronic structures that expose plentiful catalytic active sites, which opens new ideas for the regulation of LiPSs redox kinetics. Notwithstanding many instructive reviews in the land of LSBs, while this review aims to offer a complete and shrewd summary of the current progresses in HEMs-based LSBs, including in-depth interpretation of design principles and mechanistic electrocatalysis functions as well as pragmatic perspectives.

The bio-oil was largely produced by thermal pyrolysis of Jatropha-derived biomass wastes (denoted as Jatropha bio-oil) using a Pilot Plant with a capacity of 20 kg h-1 at Thailand Institute of Scientific and Technological Research (TISTR), Thailand. Jatropha bio-oil is an unconventional type of bio-oil, which is mostly composed of fatty acids, fatty acid methyl esters, fatty acid amides and derivatives, and consequently it contained large amounts of heteroatoms (oxygen ~ 20 wt.%, nitrogen ~ 5 wt.%, sulfur ~ 1000 ppm.). The heteroatoms, nitrogen especially, are highly poisonous to the metal or sulfide catalysts for upgrading of Jatropha bio-oil. To overcome this technical problem, we reported a stepwise strategy for hydrotreating of 100 wt% Jatropha bio-oil over mesoporous sulfide catalysts of CoMo/γ-Al2O3 and NiMo/γ-Al2O3 to produce drop-in transport fuels, such as gasoline- and diesel-like fuels. This study is very different from our recent work on co-processing of Jatropha bio-oil (ca. 10 wt%) with petroleum distillates to produce a hydrotreated oil as a diesel-like fuel (Chen et al., Catalysts 2018, 8, 59; http://dx.doi.org/10.3390/catal8020059). Jatropha bio-oil was pre-treated through a slurry-type high pressure reactor under severe condition, resulting in a pre-treated Jatropha bio-oil with relatively low amounts of heteroatoms (oxygen < 20 wt.%, nitrogen < 2 wt.%, sulfur < 500 ppm.). The light and middle distillates of pre-hydrotreated Jatropha bio oil was then separated by distillation at temperature below 240 oC, and the temperature of 240-360 oC. Deep hydrotreating of light distillates over sulfide CoMo/γ-Al2O3 catalyst was performed on a batch-type high pressure reactor at 350 oC and 7 MPa of H2 gas for 5 h. The hydrotreated oil was a gasoline-like fuel, which contained 29.5 vol.% of n-paraffins, 14.4 vol.% of iso-paraffins, 4.5 vol.% of olefins, 21.4 vol. % of naphthene compounds and 29.6 wt.% of aromatic compounds, and little amounts of heteroatoms (nearly no oxygen and sulfur, and less than 50 ppm of nitrogen), corresponding to an octane number of 44, and it would be suitable for blending with petro-gasoline. The hydrotreating of middle distillates over sulfide NiMo/γ-Al2O3 catalyst using the same reaction condition produced a hydrotreating oil with diesel-like composition, low amounts of heteroatoms (no oxygen and less than 50 ppm of sulfur and nitrogen), and a cetane number of 60, which would be suitable for use in drop-in diesel fuel.

One of the most burning topics in cybersecurity in 2023 will undoubtedly be the compliance with the Software Bill of Materials. Since the US president issued the Executive Order 14028 on Improving the Nation’s Cybersecurity, software developers have prepared and bills are transmitted to vendors, customers, and users, but they don’t know what to do with the reports they are getting. In addition, since software developers have identified the values of the Software Bill of Materials, they have been using the reports extensively. This article presents an estimate of 270 million requests per month, just from form one popular tool to one vulnerability index. This number is expected to double every year and a half. This simple estimate explains the urgency for automating the process. We propose solutions based on artificial intelligence and machine learning, and we base our tools on the existing FAIR principles (Findable, Accessible, Interoperable, and Reusable). This methodology is supported with a case study research and Grounded theory, for categorising data into axis, and for verifying the values of the tools with experts in the field. We showcase how to create, and share Vulnerability Exploitability eXchange data, and automate the Software Bill of Materials compliance process with AI models and a unified computational framework combining solutions for the following problems: (1) the data utilisation problem, (2) the automation and scaling problem, (3) the naming problem, (4) the alignment problem, (5) the pedigree, and provenance problem, and many other problems that are on the top of mind for many security engineers at present. The uptake of these findings will depend on collaborations with government and industry, and on the availability and the ease of use of automated tools.

Li-rich layered oxide cathode materials have become one of the most promising cathode materials for high-energy-density lithium-ion batteries owning to its high theoretical specific capacity, low cost, high operating voltage and environmental friendliness. Yet they suffer from severe capacity and voltage attenuation during prolong cycling, which blocks their commercial application. To clarify these causes, we synthesize 0.5Li2MnO3·0.5LiNi0.8Co0.1Mn0.1O2 (LL-811) with high-nickel-content cathode material by a solid-sate complexation method, and it manifests a lot slower capacity and voltage attenuation during prolong cycling compared to LL-111 and LL-523 cathode materials. The capacity retention at 1C after 100 cycles reaches to 87.5% and the voltage attenuation after 100 cycles is only 0.460 V. Combining X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscopy (TEM), it indicates that increasing the nickel content not only stabilizes the structure but also alleviates the attenuation of capacity and voltage. Therefore, it provides a new idea for designing of Li-rich layered oxide cathode materials that suppress voltage and capacity attenuation.

The biomimetic design of engineering structures is based on biological structures with excellent mechanical properties, which are the result of billions of years of evolution. However, current biomimetic structures, such as ordered lattice materials, are still inferior to many biological materials in terms of structural complexity and mechanical properties. For example, the structure of \textit{Euplectella aspergillum}, a type of deep-sea glass sponge, is an eye-catching source of inspiration for biomimetic design; however, guided by scientific theory, how to engineer structures surpassing the mechanical properties of \textit{E. aspergillum} remains an unsolved problem. The lattice structure of the skeleton of \textit{E. aspergillum} consists of vertically, horizontally, and diagonally oriented struts, which provide superior strength and flexural resistance compared with the conventional square lattice structure. Herein, the structure of \textit{E. aspergillum} was investigated in detail, and by using the theory of elasticity, a lattice structure inspired by the bionic structure was proposed. The mechanical properties of the sponge-inspired lattice structure surpassed the sponge structure under a variety of loading conditions, and the excellent performance of this configuration was verified experimentally. The proposed lattice structure can greatly improve the mechanical properties of engineering structures, and it improves strength without much redundancy of material. This study achieved the first surpassing of the mechanical properties of an existing sponge-mimicking design. This design can be applied to lattice structures, truss systems, and metamaterial cells.

Water splitting technology is an efficient approach to generate hydrogen (H2) energy, which can well address the problems of environmental deterioration and energy shortage, as well as establishment of a clean and sustainable hydrogen economy powered by renewable energy sources due to the green reaction of H2 with O2. While the efficiency of H2 production by water splitting technology is intimately related with the reactions on electrode. Nowadays, the efficient electrocatalysts in water splitting reactions are the precious metal-based materials, i.e., Pt/C, RuO2 and IrO2. Ni (Co, Fe)-based layered double hydroxides (LDH) 2D materials are the typical non-precious metal-based materials in water splitting with advantages of low cost, excellent electrocatalytic performance and simple preparation methods, which exhibits a great potential for the substitution for precious metal-based materials. This review summarizes the recent progress of Ni (Co, Fe)-based LDH 2D materials for water splitting, which mainly focuses on discussing and analyzing the different strategies to modify LDH materials towards high electrocatalytic performance. We also discuss the recent achievements including their electronic structure, electrocatalytic performance, catalytic center, preparation process and catalytic mechanism. Furthermore, the characterization progress in revealing electronic structure and catalytic mechanism of LDH is highlighted in this review. Finally, we put forward some future perspectives related to design and explore advanced LDH catalysts in water splitting.

In the past decade, under the background of the carbon peaking and carbon neutrality era, the rapid development of new energy vehicles has put forward higher requirements for the performance of strike forces such as battery cycle life, energy density and cost. Lithium-ion batteries have gradually become the mainstream of electric vehicle power batteries due to their excellent energy density, rate performance and cycle life. At present, the most widely used cathode materials for power batteries are lithium iron phosphate (LFP) and ternary nickel-cobalt-manganese (NCM). However, these materials exhibit the bottlenecks that limit the improvement and promotion of power battery performance. In this review, the performance characteristics, cycle life attenuation mechanism (including structural damage, gas generation and active lithium loss, etc.) and improvement methods (including surface coating and element-doping modification) of LFP and NCM batteries are reviewed. Finally, the development prospects of this field are proposed.

Oxide semiconductors are conventionally being used as sensing materials in gas sensors, limiting the detection of gases at room temperature (RT). In this work, a hybrid of copper oxide (CuO) with functionalized graphene (rGO) is proposed to achieve gas sensing at RT. The combination of high surface area and presence of many functional groups in CuO/rGO hybrid material makes it highly sensitive for gas absorption and desorption. To prepare the hybrid material, a copper oxide suspension synthesized using copper acetate precursor is added to the graphene oxide solution during its reduction using ascorbic acid. Material properties of CuO/rGO hybrid and its drop-casted thin films are investigated using Raman, FTIR, SEM, TEM, and four-point probe measurement systems. We find that the hybrid material is enriched with oxygen functional groups (OFGs) and defective sites along with electrical conductivity (~1.5 kΩ/□). The fabricated QCM (quartz crystal microbalance) sensor with a thin layer of CuO/rGO hybrid, demonstrates a high sensing response which is twice the response of the rGO-based sensor for CO₂ gas at RT. We believe that the CuO/rGO hybrid can be highly suitable for existing and future gas sensors used for domestic and industrial safety.

The statistics of grain displacements probability distribution function (pdf) during the shear of a granular medium displays an unusual dependence with the shear increment upscaling as recently evinced [Phys. Rev. Lett. 115 238301 2015]. Basically, the pdf of grain displacements has clear nonextensive ($q$-Gaussian) features at small scales but approaches to Gaussian characteristics at large shear window scales -- the granulence effect. Here, we extend this analysis studying a larger system (more grains considered in the experimental setup) which exhibits a severe shear band fault during the macroscopic straining. We calculate the pdf of grain displacements and the dependency of the $q$-statistics with the shear increment. This analysis have shown a singular behavior of $q$ at large scales, displaying a non-monotonic dependence with the shear increment. By means of an independent image analysis, we demonstrate that this singular non-monotonicity could be associated with the emergence of a shear band within the confined system. We show that the exact point where the $q$-value inverts its tendency coincides with the emergence of a giant percolation cluster along the system, caused by the shear band. We believe that this original approach using Statistical Mechanics tools to identify shear bands can be a very useful piece to solve the complex puzzle of the rheology of dense granular systems.

The paper describes problems with the current additive manufacturing chain before considering additive manufacturing as part of a modern manufacturing chain. Additive manufacturing can be used for near net-shape for finishing, for repair or for adding special features which cannot be made with traditional manufacturing. This paper describes how STEP-NC deals with these different scenarios in terms of accuracy, multi-material and variation of slice direction. The possibilities of multi-material objects also raises questions about the design of such objects and how these need to be handled by an advanced controller. The paper also describes non-planar slicing. Curved direction and cylindrical direction are shown to improve the accuracy of curved structure additive manufacturing. STEP-NC using boundary representation has better capability of depicting complex internal structures for additive processes. By using exact model of the final product represented by STEP-NC, the paper demonstrates improvements in data size reduction, slicing accuracy, and precise manipulation of internal structure.

Recently, several research groups have reported on anomalous enhancement of the self-field critical currents, Ic(sf,T), at low temperatures in superconductor/Dirac-cone material/superconductor (S/DCM/S) junctions. Some papers attributed the enhancement to the low-energy Andreev bound states arising from winding of the electronic wave function around DCM. In this paper, Ic(sf,T) in S/DCM/S junctions have been analyzed by two approaches: modified Ambegaokar-Baratoff and ballistic Titov-Beenakker models. It is shown that the ballistic model is an inadequate tool to analyze experimental data from S/DCM/S junctions. The primary mechanism for limiting superconducting current in S/DCM/S junctions is different from the conventional view that the latter is the maximum value within the order parameter phase variation. Thus, there is a need to develop a new model for self-field critical currents in S/DCM/S systems.

Bamboo is the building material of the past and future. It offers numerous properties that make it versatile for various applications, including construction. Its impressive strength-to-weight ratio enables it to bear substantial loads and stresses, while its good elasticity allows efficient energy absorption. However, its mechanical properties can vary based on factors such as species, age, locations, methods, and treatment. Treating bamboo is essential to enhance its properties and durability. The literature provides various natural and chemical treatments which enhanced some of the properties but also reported a drawbacks on higher temperature, content and duration. This paper reviewed 57 articles from Scopus database, specifically focusing on article-document type publications from the years 2003 to 2023. Additional references were also incorporated to address concerns in properties, treatment and standards to provide systematic understanding. MATLAB was utilized for data text analytics. With extensive assessment on the articles, the following gaps and concerns were observed and recommends for further study and assessment such as for bamboo properties, the development of centralized guidelines and procedures for the preparation and processing; exploration of alternative materials to reinforce bamboo without compromising its ductility; development of joint connections, and testing of mechanical properties considering seismic, wind and vibration. For treatment methods, the standardization of procedures using natural, chemical or combination. Lastly, for bamboo codes and standards, assessment of existing codes and standards for testing the mechanical properties of bamboo highlighting the potential limitations and areas, uniformity, differences with all existing similar standards. By filling these gaps, it can support the reliability and robustness of bamboo as a sustainable material, fostering its promotion and adoption in construction industry.

With superior optical properties, high flexibility in engineering its material properties, and strong capability for large-scale on-chip integration, graphene oxide (GO) is an attractive solution for on-chip integration of two-dimensional (2D) materials to implement functional integrated photonic devices capable of new features. Over the past decade, integrated GO photonics, representing an innovative merging of integrated photonic devices and thin GO films, has experienced significant development, leading to a surge in many applications covering almost every field of optical sciences. This paper reviews the recent advances in this emerging field, providing an overview of the optical properties of GO as well as methods for the on-chip integration of GO. The main achievements made in GO hybrid integrated photonic devices for diverse applications are summarized. The open challenges as well as the potential for future improvement are also discussed.

Gamma titanium aluminides (γ-TiAl) present an excellent behaviour under high temperature conditions, being a feasible alternative to nickel-based superalloy components in aeroengine sector. However, considered as a difficult to cut material, process cutting parameters require special study to guarantee components quality. In this work, developed drilling mechanistic model is a useful tool in order to predict drilling force (F_z) and torque (T_c) for optimal drilling conditions determination. The model is validated for three types of Gamma-TiAl alloys. Integral hard metal end-drilling tools and different cutting parameters (feeds and cutting speeds) are tested in three different sized holes for each alloy.

Nano-scale organofunctional silanes have been developed, tested and successfully applied to protect stone buildings in Europe against climatic effects since the 1860s. The same nanotechnologies can also be used in pavement engineering to create strong chemical bonds between a stabilising agent and the material substrata. The attachment of the organofunctional silane to a material also makes the surface of the material hydrophobic, reducing future chemical weathering. These properties allow naturally available materials to be used in any pavement layer at a low risk. In the built environment, scientists soon determined that the successful use of an organo-silane depends on the type and condition of the stone to be treated. The same principles apply to the implementation of applicable nanotechnologies in pavement engineering. Understanding the basic chemistry determining the properties of the stabilising agent and the organofunctional modifying agent and the chemical interaction with the primary and secondary minerals of the material are essential for the successful application of these technologies in pavement engineering. This paper explains some basic chemistry which fundamentally influences engineering outputs that can be achieved using New-age (Nano) Modified Emulsions (NME) stabilising agents with naturally available material in all road pavement TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back

Alkali-activated materials are alternative building binders, where secondary raw materials are processed. Possibility to use landfilled waste materials in their preparation, increases their potential application in construction practice, and therefore they are subject to extensive research, especially in recent years. This paper briefly summarizes interesting results of an experiment aimed at verifying the possibility of applying cement by-pass dust (CBPD) in the preparation of alkali-activated materials. The research work was focused on the possibilities of using these wastes for the preparation of small elements of garden architecture. The paper briefly evaluates in particular the results of X-ray diffraction, which were subjected to three types of binder pastes differing in the amount of used activator. In the experiment, a mixture of blast furnace granulated slag, fly ash and cement by-pass dust was alkali activated with sodium metasilicate.

Environmentally friendly and low-cost sensors are needed for the next generation disposable electronics applications. Given its low-cost, availability and biodegradability, paper-based devices are a very promising. Here we demonstrate the fabrication of a tungsten disulphide (WS2) strain sensor on standard copy paper. The WS2 is deposited through direct abrasion of WS2 powder against the paper surface making the fabrication of the device low-tech and cost effective. The fabricated strain gauge devices present gauge factors up to ~70 for strains in the ± 0.5 % range. These values are ~ 9 times larger than that obtained on devices with the same geometry but using a graphite film instead a WS2 as a sensitive material. We demonstrate the potential of these WS2-on-paper strain gauges by integrating them directly on a paper cantilever to sense mass and forces. We show how this very simple device can detect sub-milligram masses. Moreover, we also demonstrate the capability of transducing motion in mechanical resonators by gluing a WS2-on-paper strain gauge on their surface.

The modern material design aims to achieve multifunctionality by integrating structures in a diverse range, resulting in simple materials with embedded functions. Biological materials and organisms are typical examples of this concept, where complex functionalities are achieved through a limited material base. This review highlights the inspiration from multifunctional organisms and materials in nature, emphasizing their structural and functional integration. In particular, we discuss complex hierarchical architectures ranging from the nanoscale to the macroscale, to achieve multifunctional properties such as extreme pressure, impact and wear resistance, shape memory and self-healing, adhesiveness and anti-fouling, sensing-actuating and sensing-camouflage, and extreme environmental survival. These strategies of integrating structure and function are critical for promoting innovations and breakthroughs in the modern engineering materials and applications.

Perovskite solar cells are an evolving technology owing to self-assembling and highly tunable bandgap properties of materials. In this context, thin films of perovskites have attracted immense attention and witnessed great advancement because of their low manufacturing cost. The key development in these devices is the conversion efficiency, which rose from 3.8% to 28%. The formulation of innovative materials with the proper replacement of lead in perovskites is imperative to mitigate lead toxicity. Here, we analyzed the challenges like material and structural stability, device stability under high temperature and humidity conditions, lifetime, manufacturing cost, etc. faced in the commercialization of perovskite devices. This review shows that challenges such as device engineering, performance stability against the harsh environment, cost-effectiveness, and environmental concern should be taken into consideration for the widespread acceptance of perovskite-based solar devices. In conclusion, we suggested that an enormous scope exists for exploring high-performance and long-lasting perovskites for energy applications.

All-optical signal processing based on nonlinear optical devices is promising for ultrafast information processing in optical communication systems. Recent advances in two-dimensional (2D) layered materials with unique structures and distinctive properties have opened up new avenues for nonlinear optics and the fabrication of related devices with high performance. This paper reviews the recent advances in research on third-order optical nonlinearities of 2D materials, focusing on all-optical processing applications in the optical telecommunications band near 1550 nm. First, we provide an overview of the material properties of different 2D materials. Next, we review different methods for characterizing the third-order optical nonlinearities of 2D materials, including the Z-scan technique, third-harmonic generation (THG) measurement, and hybrid device characterization, together with a summary of the measured n₂ values in the telecommunications band. Finally, the current challenges and future perspectives are discussed.

Interference fits are a very common shaft-hub connection due to their low manufacturing cost and excellent technical properties. Plastic Conditioning of this machine element is a new and not very well known method. By exploiting residual stresses and the associated increase in the yield point, these components can absorb operating loads such as rotating bending moments, torsion, temperature changes and centrifugal forces purely elastically and avoid plastic deformation during operation. Compared to conventionally joined interference fits, the load bearing capacity in the elastic range can be increased by almost 200% and a specifically defined additional safety against plastic deformation in the elastic-plastic range can be ensured. This paper examines the effects of Reverse Yielding on the technology of Plastic Conditioning of Interference Fits in Power Transmission Engineering. Based on the Shear Stress Hypothesis (SH), the Plane Stress State (PSS) and the ideal plastic behavior of materials, the stress-mechanical relationships are explained, the influencing parameters are examined and conclusions are drawn for the plastic conditioning process. Taking into account the theoretical knowledge according to the state of the art, modified material behavior assumptions (isotropic hardening) and the Von Mises Yield Criterion (VMYC) are also considered. In addition, the method of plastic conditioning of interference fits is introduced and its basic principles are briefly explained. Along with computational suggestions to avoid Reverse Yielding, open issues requiring further research are identified.

An ability of different molecular potentials to reproduce the properties of 2D molybdenum disulphide polymorphs is examined. Structural and mechanical properties, as well as phonon dispersion of the 2H, 1T and 1T’ single-layer MoS2 (SL MoS2) phases, were obtained using density functional theory (DFT) and molecular statics calculations (MS) with Stillinger-Weber, REBO, SNAP, and ReaxFF interatomic potentials. Quantitative systematic comparison and discussion of the results obtained are reported.

Recently, Kayyalha et al. (Phys. Rev. Lett., 2019, 122, 047003) reported on anomalous enhancement of the self-field critical currents, I_c (sf,T), at low temperatures in Nb/BiSbTeSe₂-nanoribbon/Nb Josephson junctions. The enhancement was attributed to the low-energy Andreev bound states arising from winding of the electronic wave function around the circumference of the topological insulator BiSbTeSe₂ nanoribbon. In this paper, we show that identical enhancement in I_c(sf,T) and in the upper critical field, B_c2(T), at approximately same reduced temperatures, were reported by several research groups in atomically thin junctions based on a variety of Dirac-cone materials (DCM) earlier. Our analysis shows that in all these S/DCM/S systems the enhancement is due to a new superconducting band opening. Taking in account that several intrinsic superconductors also exhibit the effect of new superconducting band(s) opening when sample thickness becomes thinner than the out-of-plane coherence length, we strength our previous proposal that there is a new phenomenon of additional superconducting band(s) opening in atomically thin films.

The carbonized elastomer-based composites (CECs) possess a number of attractive features in terms of thermomechanical and electromechanical performance, durability in aggressive media and facile net-shape formability, but their relatively low ductility and strength limit their suitability for structural engineering applications. Prospective applications such as structural elements of MEMS can be envisaged, since smaller principal dimensions reduce the susceptibility of components to residual stress accumulation during carbonization, and to brittle fracture in general. We report the results of operando in-SEM study of micro-deformation and fracture behavior of CECs based on NBR elastomeric matrices filled with carbon and silicon carbide. Nanostructured carbon composite materials were manufactured via compounding of elastomeric substance with carbon and SiC fillers using mixing rolling mill, vulcanization, and low-temperature carbonization. Double Edge Notched Tensile (DENT) specimens of vulcanized and carbonized elastomeric composites were subjected to in situ tensile testing in the chamber of the scanning electron microscope (SEM) Tescan Vega 3 using Deben Microtest 1 kN Tensile Stage. The series of acquired SEM images were analyzed by means of Digital Image Correlation (DIC) using Ncorr open source software to map the spatial distribution of strain. These maps were correlated with Finite Element Modelling (FEM) simulations to refine the values of elastic moduli. Besides, the elastic moduli were derived from unloading curve nanoindentation hardness measurements carried out using NanoScan-4D tester and interpreted using the Oliver-Pharr method. Carbonization causes significant increase of elastic moduli from 0.86 ± 0.07 to 14.12 ± 1.20 GPa for the composite with graphite and carbon black fillers. Nanoindentation measurements yield somewhat lower values, namely, 0.25 ± 0.02 GPa and 9.83 ± 1.10 GPa before and after carbonization respectively. The analysis of fractography images suggests that crack initiation, growth and propagation may occur both at the notch stress concentrator and relatively far from the notch. Possible causes of such response are discussed, namely, (1) residual stresses introduced by processing; (2) shape and size of fillers; and (3) the emanation and accumulation of gases in composites during carbonization.

As a novel layered noble metal dichalcogenide material, palladium diselenide (PdSe₂) has attracted wide interest due to its excellent optical and electronic properties. In this work, a strong third-order nonlinear optical response of 2D PdSe₂ films is reported. We conduct both open-aperture (OA) and closed-aperture (CA) Z-scan measurements with a femtosecond pulsed laser at 800 nm to investigate the nonlinear absorption and nonlinear refraction, respectively. In the OA experiment, we observe optical limiting behaviour originating from large two photo absorption (TPA) in the PdSe₂ film of β = 3.26 ×10^-8 m/W. In the CA experiment, we measure a peak-valley response corresponding to a large and negative Kerr nonlinearity of n₂ = -1.33×10^-15 m²/W – two orders of magnitude larger than bulk silicon. In addition, the variation of n₂ as a function of laser intensity is also characterized, with n₂ decreasing in magnitude when increasing incident laser intensity, becoming saturated at n₂ = -9.96×10^-16 m²/W at high intensities. Our results show that the extraordinary third-order nonlinear optical properties of PdSe₂ have strong potential for high-performance nonlinear photonic devices. Keywords: 2D materials, PdSe₂ films, Z-scan technique, Kerr nonlinearity, nonlinear photonics.

The hydrothermal synthesis of aluminophosphate molecular sieve type AlPO4-11 was processed from chemicals containing psueudobohemite, 85% phosphoric acid, water, and di-isopropylamine as templating agent. The crystallization of the samples was studied by taking samples in times from 2 to 74 hours. The obtained white powder products have been characterized by XRD patterns, FT-IR spectra, thermogravimetric data, scanning electron microscopy and pH measurement of the mother liquor. The pore volume, as determined from TG and DTG curves, was ca. 0.17 cm3g-1. The crystallization process of the aluminophosphate exhibited in its initial phase a behavior of first order reaction with a specific velocity constant of ca. 0.25 h-1, as determined from XRD and FT-IR data.

Lithium rich layered oxides (LRLO) are a wide class of innovative active materials for positive electrodes in lithium-ion (LIB) and lithium-metal secondary batteries (LMB). LRLOs are over-stoichiometric layered oxides rich in lithium and manganese, with general formula Li1+xTM1-xO2, where TM is a blend of transition metals comprising Mn (main constituent), Ni, Co, Fe and others. Due to the very variable composition and the extended defectivity their structural identity is still debated among researchers being likely an unresolved hybrid between a monoclinic (mC24) and a hexagonal lattice (hR12). Once casted in composite positive electrode films and assembled in LIBs or LMBs, LRLOs can delivery reversible specific capacities above 220-240 mAhg-1, thus beyond any other available intercalation cathode material for LIBs, with mean working potential above 3.3-3.4 V vs Li for hundreds of cycles in liquid aprotic commercial electrodes. In this review we critically outline the recent advancements in the fundamental understanding of the physico-chemical properties of LRLO as well as the most exciting innovations in their battery performance. We focus in particular on the elusive structural identity of these phases, on the complexity of the reaction mechanism in batteries as well as on practical strategies to minimize or remove cobalt from the lattice while preserving the outstanding performance upon cycling.

Eco-friendly betanin/clay minerals hybrid materials with good stability were synthesized combining natural betanin molecules extracted from beetroot with 2:1 type palygorskite (Pal) and 1:1 type halloysite (Hal), respectively. It was found that the adsorption, grinding and heating treatment played a key role to enhance the interaction between betanin and clay minerals during preparation process, which favored improving the thermal stability and solvent resistance of natural betanin. The L* and a* values of the betanin/Pal and betanin/Hal hybrid materials were 64.94 and 14.96, 62.55 and 15.48, respectively, indicating that betanin/Hal exhibited the better color performance. The structural characterizations confirmed that betanin was mainly adsorbed on the outer surface of Pal or Hal through hydrogen-bond interaction, and part of them also were entered into the inner surface of Hal via electrostatic interaction. Therefore, Hal preferred to improve the color properties, heating stability and solvent resistance of natural betanin due to its structural features compared with Pal.

Low-dimensional carbon-based (LDC) materials have attracted extensive research attentions in electrocatalysis because of their unique advantages such as structural diversity, low cost, and chemical tolerance. They have been widely used in a broad range of electrochemical reactions to relief environmental pollution and energy crisis. Typical examples include hydrogen evolution reaction (HER), oxygen evolution reaction (OER), oxygen reduction reaction (ORR), carbon dioxide reduction reaction (CO₂RR), and nitrogen reduction reaction (NRR). Traditional “trial and error” strategies seriously slowed down the rational design of electrocatalysts for these important applications. Recent studies show that the combination of density functional theory (DFT) calculations and experimental research is capable of accurately predicting the structures of electrocatalysts, thus could reveal the catalytic mechanisms. Herein, current well-recognized collaboration methods of theory and practice are reviewed. The history of modern DFT, commonly used calculation methods, and basic functionals are briefly summarized. Special attention is paid to descriptors that are widely accepted as a bridge links the structure and activity, and the breakthroughs for high-volume accurate prediction of electrocatalysts. Importantly, correlating multiple descriptors are used to systematically describe the complicated interfacial electrocatalytic processes of LDC catalysts. In addition, machine learning and high-throughput simulations are crucial in assisting the discovery of new multiple descriptors and reaction mechanisms. This review will guide the further development of LDC electrocatalysts for extended applications from the aspect of DFT computations.

This paper discusses the use of fly ash in concrete construction industry. Fly ash is incorporated as a supplementary cementitious material (SCM) in ordinary Portland cement (OPC) concrete in partial replacement of cement, and is recently used as a geopolymer cement in the development of geopolymer concrete (GPC) mixes. Class C and Class F fly ash high aluminosilicate content, and fine granular size contributes to concrete improved workability, lower permeability, and reduced heat of cement hydration. Due to its chemical properties, the use of fly ash in producing OPC and GPC results in increased compressive strength, higher tensile strength evaluated by measuring hardened concrete modulus of rupture (MOR), and higher modulus of elasticity (MOE). The fine size of fly ash particles increases the concrete mix packing order, and reduce the ingress of moisture, and mitigates the impact of aggressive environmental attacks through the reduction of sulfates and chlorides rate of concrete penetration. Thus, fly ash improves concrete resistivity to alkali-aggregate reactions (AAR), and reduces the corrosion of reinforcing steel, and prestressing strands. Fly ash as an economic byproduct of coal industry results in reduced material cost, increased durability, and a higher sustainability of concrete construction projects.

To design and optimize liquid-assisted processes such as reactive infiltration for fabricating refractory SiC/ZrSi₂ composites, basic investigations on the interfacial phenomena occurring when liquid Si-based alloys are in contact with C and SiC substrates, are key steps. Indeed, targeted wettability studies may provide helpful indications for finding the suitable set of operating conditions to succeed the fabrication of composites via the reactive infiltration and for predicting the key influencing mechanisms. The wettability of glassy carbon (GC) by two different Si-rich Si-Zr alloys as a function of the Si-content has been investigated by the sessile drop method at T = 1450°C. The more relevant results obtained in terms of equilibrium contact angle values, spreading kinetics, reactivity and developed interface microstructures are reported in the paper and compared with the behaviour previously observed in the Si-27Zr/GC system. The increase of Si-content only weakly affected the overall phenomena observed at the interface, which from the practical point of view means that even the Si-Zr alloys with higher Si-content, as respect to the eutectic alloy (Si-27Zr), could be potentially used as infiltrant materials.

Over the past few years, there has been an increasing fascination with electric unmanned aerial vehicles (UAVs) because of their capacity to undertake demanding and perilous missions, while also delivering advantages in terms of flexibility, safety, and expenses. These UAVs are revolutionizing various public services, encompassing real-time surveillance, search and rescue operations, wildlife assessments, delivery services, wireless connectivity, and precise farming. To enhance their efficiency and duration, UAVs typically employ a hybrid power system. This system integrates diverse energy sources, such as fuel cells, batteries, solar cells, and supercapacitors. The selection of an appropriate hybrid power arrangement and the implementation of an effective energy management system are crucial for the successful functioning of advanced UAVs. This article specifically concentrates on UAV platforms powered by batteries, incorporating innovative technologies like in-flight recharging via laser beams and tethering. It provides an all-encompassing and evaluative examination of the current cutting-edge power supply configurations, with the objective of identifying deficiencies, presenting perspectives, and offering recommendations for future consideration in this domain.

Miniaturization of electronics devices is often limited by the concomitant high heat fluxes (cooling load) and maldistribution of temperature profiles (hot spots). Thermal energy storage (TES) platforms providing supplemental cooling can be a cost-effective solution, that often leverages phase change materials (PCM). Although salt hydrates provide higher storage capacities and power ratings (as compared to that of the organic PCMs), they suffer from reliability issues (e.g., supercooling). ‘Cold Finger Technique (CFT)’ can obviate supercooling by maintaining a small mass fraction of the PCM in solid state for enabling spontaneous nucleation. Optimization of CFT necessitates real-time forecasting of the transient values of the melt-fraction. In this study artificial neural network (ANN) is explored for real-time prediction of the time remaining to reach a target value of melt-fraction based on the prior history of the spatial distribution of the surface temperature transients. Two different approaches were explored for training the ANN model, using: (1) transient PCM-temperature data; or (2) transient surface-temperature data. When deployed in a heat sink that leverages PCM based passive thermal management systems for cooling of electronic chips and packages, this maverick approach (using the second method) affords cheaper costs, better sustainability, higher reliability and resilience.

Geothermal energy is a weather-independent, permanently available renewable energy source. In addition to producing heat and electricity, geothermal energy can be used to extract critical raw materials dissolved in the heat-carrying fluid. Researchers working on the frontiers of geothermal energy utilisation may be able to transform ultra-deep metallic mineral formations into “orebody-Enhanced Geothermal Systems”. In the planned technology, the metal-containing geological formation would be manipulated in such a way that cogeneration of energy and metals is possible and can be optimised in the future according to market needs. The potential of geothermal energy for sustainable mineral extraction and energy production aligns with Sustainable Development Goal (SDG) 7, which aims to ensure access to affordable, reliable, sustainable, and modern energy for all. This new technology could substantially decrease Europe’s dependency on importing critical metallic minerals (such as lithium and tungsten) and energy; over and above, it has a small environmental footprint, including very low carbon emissions

The objective of this article: analysis of research trends on the topic "Materials Science for Energy Engineering" for the period 2012-2021. Materials and methods: bibliometric analysis of data from the Scopus abstract database.Results. It is shown that this topic is developing faster than the general energy topics.The key feature of the research trends is a significant increase in work on the development of materials for renewable energy and a decrease in the number of publications related to nuclear power.The primary goal of many studies is to increase the efficiency of renewable energy production through the use of new materials.The importance of the topic is evidenced by the emergence of new journals that quickly entered the first quartile of the abstract databases Scopus and Web of Science, for example: ACS Applied Energy Materials.There has been a significant increase of interest in perovskite solar cells, layered semiconductors, triboelectric nanogenerators, cobalt compounds, sulfur compounds, and oxygen and hydrogen evolution reaction during Electrolysis.Publications on electric batteries are well represented in all time intervals. The focus is on electrode materials and battery efficiency.

A novel stationary phase for affinity separations is presented. This material is based on sintered borosilicate glass readily available as semi-finished filter plates with defined porosity and surface area. The material shows fast binding kinetics and excellent long-term stability under real application conditions due to lacking macropores and high mechanical rigidity. The glass surface can be easily modified with standard organosilane chemistry to immobilize selective binders or other molecules used for biointeraction. In this paper, the manufacturing of the columns and their respective column holders by 3D printing is shown in detail. The model system protein A/IgG was chosen as an example to examine the properties of such monolithic columns under realistic application conditions. Several specifications, such as (dynamic) IgG capacity, pressure stability, long-term performance, productivity, non-specific binding, and peak shape, are presented. It could be shown that due to the very high separation speed, 250 mg antibody per hour and column can be collected, which surpasses the productivity of most standard columns of the same size. The total IgG capacity of the shown columns is around 4 mg (5.5 mg/mL), which is sufficient for most tasks in research laboratories. The cycle time of an IgG separation can be less than 1 minute. Due to the glass material's excellent pressure resistance, these columns are compatible with standard HPLC systems. This is usually not the case with standard affinity columns, limited to manual use or application in low-pressure systems. The use of a standard HPLC system also improves the ability for automation, which enables the purification of hundreds of cell supernatants in one day. The sharp peak shape of the elution leads to an enrichment effect, which might increase the concentration of IgG by a factor of 3. The final concentration of IgG can be around 7.5 mg/mL without the need for an additional nanofiltration step. The purity of the IgG was > 95% in one step and nearly 99% with a second polishing run.

: Medical gloves, along with masks and gowns, serve as the initial line of defense against poten-tially infectious microorganisms and hazardous substances in the health sector. During the COVID-19 pandemic, medical gloves played a significant role, as they were widely utilized by society in daily activities as a preventive measure. These products demonstrated their value as important personal protection equipment (PPE) and reaffirmed their relevance as infec-tion-prevention tools. This review describes the evolution of medical gloves since the discovery of vulcanization by Charles Goodyear in 1839, which fostered the development of this industry. Regarding the current market, a comparison of the main properties, benefits, and drawbacks of the most widespread types of sanitary gloves is presented. The most usual gloves are produced from natural rubber (NR), polyisoprene (IR), acrylonitrile butadiene rubber (NBR), polychloroprene (CR), polyethylene (PE), and poly(vinyl chloride) (PVC). Furthermore, the environmental impacts of the conventional natural rubber gloves manufacturing process and mitigation strate-gies, such as bioremediation and rubber recycling, are addressed. In order to create new smart medical gloves with improved properties, several biopolymers (e.g. poly(vinyl alcohol) and starch) and additives such as biodegradable fillers (e.g., cellulose and chitin), reinforcing fillers (e.g. silica and cellulose nanocrystals), and antimicrobial agents (e.g., biguanides and quaternary ammonium salts) have been evaluated. This paper covers these smart materials and describes different innovative prototypes of gloves and coatings designed with them.

The development of smart negative electrode materials with high capacitance for use in supercapacitors remains challenging. Although there have been several types of electrode materials with high capacitance used in energy storage, carbon-based materials are the most reliable electrodes due to their high conductivity, high power density and excellent stability. The most common complaint about general carbon materials is that these as-formed electrode materials can hardly ever be used as free-standing electrodes. Free-standing carbon-based electrodes are in high demand and are a passionate topic of energy storage research. Electrospun nanofibers are a potential candidate to fill this gap. However, the as-spun carbon nanofibers (ECNFs) have low capacitance and energy density on their own. To this end, several attempts have been made to improve these characteristics. In this review, we introduce negative electrode materials that have been developed. Moreover, this review places special attention to the advances of electrospun nanofiber-based negative electrode materials and their limitations. Based on the above information, we put forth a future perspective on how these limitations can be overcome to meet the demands of next-generation smart devices.

Cranio-maxillofacial structure is a region of particular interest in the field of regenerative medicine due to both its anatomical complexity and the numerous abnormalities affecting this area. However, this anatomical complexity is what makes possible the coexistence of different microbial ecosystems in the oral cavity and the maxillofacial region, contributing to the increased risk of bacterial infections. In this regard, different materials have been used for their application in this field. These materials can be obtained from natural and renewable feedstocks or by synthetic routes with desired mechanical properties, biocompatibility and antimicrobial activity. Hence, in this review, we have focused on bio-based polymers, which by their own nature, by chemical modifications of their structure, or by their combination with other elements, provide a useful antibacterial activity as well as the suitable conditions for cranio-maxillofacial tissue regeneration. This approach has not been reviewed previously, and we have specifically arranged the content of this article according to the resulting material and its corresponding application, reviewing guided bone regeneration membranes; bone cements; and devices and scaffolds for both soft and hard maxillofacial tissue regeneration, including hybrid scaffolds, dental implants, hydrogels and composites.

The non-linear analysis of hollow-core concrete slabs requires the use of advanced numerical techniques, proper constitutive models both for concrete and steel as well as particular computational skills. If prestressing, cracking, crack opening, material softening, etc. are also to be taken into account, then the computational task can far exceed the capabilities of an ordinary engineer. In order for the calculations to be carried out in a traditional design office, simplified calculation methods are needed. Preferably based on the linear finite element (FE) method with a simple approach that takes into account material nonlinearities. In this paper the simplified analysis of hollow-core slabs based on the generalized nonlinear constitutive law is presented. In the proposed method a simple decomposition of the traditional iterative linear finite element analysis and the non-linear algebraic analysis of the plate cross-section is used. Through independent analysis of the plate cross-section in different deformation states, a degraded plate stiffness can be obtained, which allows iterative update of displacements and rotations in the nodes of the FE model. Which in turn allows to update the deformation state and then correct translations and rotations in the nodes again. The results obtained from the full detailed 3D nonlinear FEM model and from the proposed approach are compared for different slab cross-sections. The obtained results from both models are consistent.

Metallic thin-film materials and nanoparticles (mainly Silver (Ag)-based) are recently being used in many nano-technological applications including sensors, reflective heat-mirror coatings, and antibacterial coatings as well. The physical vapor deposition technique attracts significant attention for Ag-based nanocomposites with tailoring the structural and optical properties of metallic thin films thus allowing further improvements and application possibilities in various existing fields namely electronics, catalysis, magnetics, optics in alongside the environment and health and new emergent fields in, particularly thin-film coatings. This study highlights the preparation, characterization, properties, and possible future application directions of several types of Silver (Ag)-based nanocomposite thin films prepared by using physical vapor deposition techniques.

This work focuses on analyzing acoustic emission (AE) signals as a means to predict failure in structures. Two main approaches are considered: (i) long-range correlation analysis using both the Hurst (H) and the Detrended Fluctuation Analysis (DFA) exponents, and (ii) natural time domain (NT) analysis. These methodologies are applied to the data collected from two application examples: a glass fiber reinforced polymeric plate and a spaghetti bridge model, where both structures were subjected to increasing loads until collapse. A traditional (AE) signal analysis is also performed to reference the study of the other methods. Results indicate that the proposed methods yield a reliable indication of failure in the studied structures.

In this work we explored how solvents can affect olefin oxidation reactions catalyzed by MCM-bpy-Mo catalysts and whether their control can be made with those players. The results of this study evidenced that polar and apolar aprotic solvents modulated the reactions in different ways. Experimental data showed that acetonitrile (aprotic polar) could hinder largely the reaction rate whereas toluene (aprotic apolar) did not. In both cases product selectivity at isoconversion was not affected. Further insights were obtained by means of neutron diffraction experiments, which confirmed the kinetic data allowing to propose a model based on substrate-solvent crosstalk by means of hydrogen bonding. In addition, the model was also validated in the ring-opening reaction (overoxidation) of styrene oxide towards benzaldehyde, which progressed when toluene was the solvent (reaching 31% styrene oxide conversion) but was strongly hindered when acetonitrile was used instead (reaching only 7% conversion), due to the establishment of H-bonds in the latter. Although this model was confirmed and validated for olefin oxidation reactions, it can be envisaged that it may also be applied to other catalytic reaction systems where reaction control is critical, while widening its use.

In 2007, the excavation of the M-30 ring road located in Madrid and the creation of a green corridor either side of the Manzanares river brought significant change to the metropolitan area. The corridor and linear park which it provided were designed to contribute to the regeneration of the fluvial ecosystem, establish links among residents on each side of the river and promote cultural and leisure activities. This paper provides a sustainability analysis of the excavation of the M-30 (involving the socio-economic and environmental impact) 14 years after its construction. In order to show such an impact, an analysis of the area both prior to the project and after completion, as well as a hypothetical solution that uses improved materials, has been performed. This entails use of the multi-criteria decision-making model named MIVES (initials in Spanish, modelo integrado de valor para una evaluación sostenible). The MIVES method is based on the application of value functions of sustainability indicators selected by socio-economic and environmental criteria, chosen by experts. Results from analysis showed that the excavation of the M-30 considerably improved the sustainability of the area (sustainable index 3.43 and 6.26 both before and after the excavation works). However, use of improved materials in contrast with the application of conventional materials slightly improved the sustainability of the work (Sustainability Index 6.26 and 6.74, respectively, of the conventional materials).

Concrete, as one of the essential construction materials is responsible for a vast amount of emissions. Using recycled materials and gray water can considerably contribute to the sustainability aspect of concrete production. Thus, finding a proper replacement for fresh water, in the production of concrete, is significant. The usage of industrial wastewater, instead of water in the concrete can is considered in this paper. In this study, 450 concrete samples are produced with different amounts of wastewater. The mechanical parameters such as slump, compressive strength, water absorption, tensile strength, electrical resistivity, rapid freezing, half-cell potential, and appearance are investigated. The results showed that the usage of industrial wastewater does not significantly change the main characteristics of concrete. Although, increasing the concentration of the wastewater can decrease durability and strength features nonlinearly.

This article is a scoping review analyzing advances in experimental studies on bacterial self-healing of concrete. From Scopus, ScienceDirect, Web of Science and Google Scholar search engine databases, 54 studies were selected for analysis, and an increasing trend of publications since 2015 was found, with India as the country with the largest research presence. Different ma-terials are used as replacement or admixture in concrete, such as fibers, particles and recycled material from construction waste. It was found that the most commonly used bacteria are Bacillus subtilis and Bacillus sphaericus, which can improve the strength of concrete by generating calcite and sealing cracks. In addition, it was found that the presence of materials such as fibers, ashes and construction recyclates can protect bacteria in an alkaline environment. The designs usually in-clude more than two experimental groups and a control. In summary, this study highlights the importance of bacterial self-healing in concrete and provides information on advances in this field of research.

The use of naturally available materials not conforming to traditional specifications or standards, in the base and sub-base layers of road pavement structures, stabilised with New-age (Nano) Modified Emulsions (NME), have been tested, implemented and successfully verified through Accelerated Pavement Testing (APT) in South Africa. This was made possible through the development and use of a design procedure addressing fundamental principles and based on scientific concepts, which are universally applicable. The understanding of and incorporation of the chemical interaction between the mineralogy of the materials and a NME stabilising agent (compatibility between the chemistry of the reactive agents and material mineralogy) into the design approach is key to achieving the required engineering properties. Stabilised materials evaluation is done using tests indicative of the basic engineering properties (physics) of compressive strengths, tensile strengths and durability. This article describes the basic materials design approach developed to ensure that organofunctional nano-silane modified emulsions can successfully be used for pavement layer construction utilising naturally available materials, at a low risk. The enablement of the use of naturally available materials in all pavement layers can have a considerable impact on the unit cost and life-cycle costs of road transportation infrastructure. TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back

Transparent, flexible, biaxially oriented polyethylene terephthalate (PET) sheets were modified by bioactive polymer-fibronectin top layers for the attachment of cells and growth of muscle fibers. Towards this end, PET sheets were grafted with 4-(dimethylamino)phenyl (DMA) groups from the in situ generated corresponding diazonium compound. The arylated sheets served as macro-hydrogen donors for benzophenone and the growth of poly(2-hydroxy ethyl methacrylate) (PHEMA) top layer by surface-confined free radical photopolymerization. The PET-PHEMA sheets were further grafted with fibronectin (FBN) through the 1,1-carbonyldiimidazole coupling procedures. The bioactive PET-PHEMA-I-FBN was then employed as a platform for the attachment, proliferation and differentiation of eukaryotic cells which after a few days gave remarkable muscle fibers, of ~120 µm length and ~45 µm thickness. We demonstrate that PET-PHEMA yields a fast growth of cells followed by muscle fibers of excellent levels of differentiation compared to pristine PET or standard microscope glass slides. The positive effect is exacerbated by crosslinking PHEMA chains with ethylene glycol dimethacrylate at initial HEMA/EGDMA concentration ratio = 9/1. This works conclusively shows that in situ generated diazonium salts provide aryl layers for the efficient UV-induced grafting of biocompatible coating that beneficially serve as platform for cell attachment and growth of muscle fibers. Beyond this work, diazonium coupling agents constitute the corner stone of next generation processes for building flexible platforms for cell adhesion and uses thereof.

The article discusses the issues related to the safety of transport of dangerous goods by road. Research on accidents in transport unambiguously points to the human factor, which is most responsible for causing the accident. Determining the causes of driver unreliability in the hu-man-vehicle-environment system requires thorough research. Unfortunately, in this case, experimental research with human involvement is limited in scope. This leaves modeling and simulation of the behavior of the human factor, i.e., the driver transporting dangerous goods. The human being, due to its complexity, is a challenging element to parameterize. The literature presents various attempts to model human actions. In their work, the authors used heuristic methods, specifically fuzzy set techniques, to build a human factor model. In these models, human actions were specified using a verbal or linguistic description. The specificity of fuzzy sets allows to "naturally" limit the "precision" in describing human behavior. The model was built based on the author's questionnaire and expert research, based on which individual features were selected. Then, the traits were assigned appropriate states. The output parameter of the model is λL - the intensity of human error. The obtained values of the intensity of the accident caused by the driver's error were implemented into the author's method of risk assessment. They constituted one of the factors determining the probability of an accident in the transport of dangerous goods, which allowed to determine the optimal route of transport of these goods characterized by the lowest risk of an undesirable event on the route. The article presents the model's assumptions, structure, and features included in the model, which have the most significant influence on shaping the intensity of human error. The results of the simulation studies showed a diversified effect of the analyzed characteristics on the driver's efficiency.

In the field of metallurgy, there are many factors that influence the final quality of cast iron. These are mainly charge materials, chemical composition, metallurgical preparation up to the final casting process. Even small deviations from metallurgical processing lead to fluctuations in melt quality and the occurrence of casting defects. Charge materials has a significant impact on the quality of cast iron, especially steel scrap, which is increasingly used from an economic and ecological point of view, especially when melting cast iron in electric furnaces. Cast iron produced from a higher proportion of steel scrap in the charge has higher hardness and tensile strength. On the other side, these cast irons has a higher tendency to chillout, brittleness, shrinkage, pearlitic microstructure, stresses and higher purity due to the difference in hardness at different wall thicknesses of the castings. It is the high hardness that is the problem in the final machining of castings. These negative properties are recorded mainly in heavy thick-walled castings with higher tensile strength and hardness. This negative effect is mainly due to the nitrogen content in the steel scrap. Based on these knowledges, operating melts were realized in the foundry's operating conditions. The influence of steel scrap in the charge and the possibility of eliminating its negative effects on the properties of cast iron were investigated.

Hypergolic materials synthesis is a new preparative technique in materials science that allows a wide range of carbon or inorganic solids with useful properties to be obtained. Previously we have demonstrated that metallocenes are versatile reagents in the hypergolic synthesis of inorganic materials, such as γ-Fe2O3, Cr2O3, Co, Ni and alloy CoNi. Here, we take one step further by using metallocene dichlorides as precursors for the hypergolic synthesis of additional inorganic phases, such as photocatalytic titania. Metallocene dichlorides are closely related to metallocenes, thus expanding the arsenal of organometallic compounds that can be used in hypergolic materials synthesis. In the present case, we show that hypergolic ignition of the titanocene dichloride-fuming nitric acid pair results in the fast and spontaneous formation of titania nanoparticles at ambient conditions in the form of anatase-rutile mixed phases. The obtained titania shows good photocatalytic activity towards Cr(VI) removal (100 % within 9 h), the latter being dramatically enhanced after calcination of the powder at 500 °C (100 % within 3 h). Worth noting, this performance was found to be comparable to that of commercially available P25 TiO2 under identical conditions. The cases of zirconocene, hafnocene and molybdocene dichlorides are complementary discussed in this work, aiming to show the wider applicability of metallocene dichlorides in the hypergolic synthesis of inorganic materials (ZrO2, HfO2, MoO2).

We theoretically investigate and optimize the performance of four-wave mixing (FWM) in microring resonators (MRRs) integrated with two-dimensional (2D) layered graphene oxide (GO) films. Owing to the interaction between the MRRs and the highly nonlinear GO films as well as to the resonant enhancement effect, the FWM efficiency in GO-coated MRRs can be significantly improved. Based on previous experiments, we perform detailed analysis for the influence of the GO film parameters and MRR coupling strength on the FWM conversion efficiency (CE) of the hybrid MRRs. By optimizing the device parameters to balance the trade-off between the Kerr nonlinearity and loss, we achieve a high CE enhancement of ~18.6 dB relative to the uncoated MRR, which is ~8.3 dB higher than previous experimental results. The influence of photo-thermal changes in the GO films as well as variations in the MRR parameters such as the ring radius and waveguide dispersion on the FWM performance is also discussed. These results highlight the significantly improved FWM performance that can be achieved in MRRs incorporating GO films

Clinical outcomes of dental restorations depends primarily on the choice of materials used and their fabrication processes. The spectrum of dental CAD-CAM (Computer-Aided Design Computer-Aided Manufacturing) materials presents a wide range of variables on what may be the most suitable material for the clinical case. This narrative review focuses on CAD-CAM dental materials based on their mechanical properties and in relation to their clinical applications. A literature review was performed on PubMed, Scopus, Web of Knowledge, and Cochrane Library. Articles addressing at least one of the following topics regarding dental materials for CAD-CAM systems: manufacturers, mechanical features, materials ’composition optical properties, clinical indications and / or outcomes were included in the review. A flowchart was performed as de-scribed in the PRISMA guidelines. Among the 564 articles found, 63 were analyzed and evaluated. Within the limitation of this narrative review, it can be concluded that all CAD-CAM materials presents a wide range of clinical applications due to their improved mechanical properties. Specifically, in addition to materials that have been in use for a long time (such as feldspathic ceramics), resin block composites can also be used for permanent restorations.

Lead-free ferroelectric perovskite N-methyl-N'-diazabicyclo[2.2.2]octonium)–ammonium triio-dide, MDABCO-NH₄I₃, nanocrystals are embedded in three different polymer fibers fabricated by the electrospinning technique. The nanofibers, which are very flexible and have a high Young modulus, behave as active piezoelectric energy harvesting sources that produce a piezoelectric voltage coefficient up to geff = 3.6 VmN-1 and show a blue intense luminescence band at 325 nm. In this work, the pyroelectric coefficient is reported for the MDABCO-NH₄I₃ perovskite inserted in electrospun fibers. At the ferroelectric-paraelectric phase transition, the embedded nanocrystals display a pyroelectric coefficient as high as 194×10-6 Cm-2k-1, within the same order of magnitude as that reported for the state-of-the-art bulk ferroelectric triglycine sulfate (TGS). The perovskite nanocrystals embedded into the polymer fibers remain stable, and no degradation is caused by oxidation.

The main goal of this study was to evaluate sugarcane bagasse ash as a partial cement replacement material. Sugarcane bagasse ash is a by-product of fuel blending in the sugar industry. Yet all economic sugar is obtained after extraction from the cane. The disposal of the discharged waste in agriculture causes environmental problems in the sugar industry. The cement industry also creates environmental problems due to carbon dioxide emissions during cement manufacturing. Initially, bagasse ash samples were collected from the rubble of the Arjo Didessa sugar factory. The crude bagasse ash was sieved with a sieve size of 250µm. The strength of grade C-25 concrete was designed using five different concrete mixture proportions ranging from 5 to 20% cement by weight, including a water-cement ratio of 0.45. Impact strength tests were conducted at 7, 14, 21, and 28 days of age for each replacement ratio. For the experimental work, a total of 60 cubic concrete specimens were cast for compressive strength tests, and 15 cylindrical concrete specimens were cast for water absorption tests. Working compressive strength results indicated that bagasse ash could replace up to 5% of ordinary Portland cement concrete.

Wounds are breaks in the continuity of the skin and the underlying tissues, due to external causes, such as cuts, blows and impacts, or even, during surgical interventions. Millions of people suffer minor or serious injuries, sometimes ending in death. Today, there are many commercially available products that promote healing from wounds. The high demand from the healthcare industry has created a huge market that continues to grow, fueling research and development of new wound healing products. In the present article, we review recent advances in wound healing products based on natural biopolymers, stem cells, and microRNAs. We analyze the advances of both, the commercial products and the products that are still in research phase, and we also include an overview of the opportunities, barriers, and regulatory issues for the commercialization of these products in the European, American, and Asian markets.