Ocular light exposure has important influences on human health and well-being through modulation of circadian rhythms and sleep, as well as neuroendocrine and cognitive functions. Current patterns of light exposure do not optimally engage these actions for many individuals, but advances in our understanding of the underpinning mechanisms and emerging lighting technologies now present opportunities to adjust lighting to promote optimal physical and mental health and performance. A newly developed, SI-compliant standard provides a way of quantifying the influence of light on the intrinsically photosensitive, melanopsin-expressing, retinal neurons that mediate these effects. The present report provides recommendations for lighting, based on an expert-scientific consensus and expressed according to this new measurement standard. These recommendations are supported by a comprehensive analysis of the sensitivity of human ‘non-visual’ responses to ocular light, are centred on an easily measured quantity (melanopic equivalent daylight (D65) illuminance), and provide a straightforward framework to inform lighting design and practice.

High electricity demand for consumption at current supply level in Indonesia led to the rising cost of electricity bills. This factor is compounded by the fact that many electric generators in Indonesia still use fossil fuels, which contributes to the high basic generation cost. UBL is one of the universities that aim to be a green campus. Our research explores the possibility of installing motion sensor to contribute on the energy efficiency. Although mostly common in developed countries, the use of motion sensor for energy efficiency is still rare, especially in Indonesia. despite rising cost and supply shortages, Indonesian buildings are still of high energy consumption. our experiment shows that simple installation of commercially available motion sensors can contribute to reduce the electricity bill from the increase of energy efficiency. One of the efforts to lower energy demand in consumer side is to use the electricity efficiently, such as turning off lights in a room when it's not in use. This method can be simply done by turning the light switches for office and classrooms, but difficult to do in public spaces such as toilets and corridors. Our experiment shows that simple installation of commercially available motion sensors can contribute to reduce the electricity bill from the increase of energy efficiency. Automatic light switches experimentally installed in sample toilet room prove that electricity consumption from the lamps can contribute to the reduction of total weekly energy that translates into Green House Gas emission reduction.

Acellular bacterial ghosts (BGs) are empty non-living bacterial cell envelopes, commonly generated by controlled expression of the cloned lysis gene E of bacteriophage PhiX174. In this study, Vibrio parahaemolyticus ghosts (VPGs) were generated by chemically induced lysis and the method is based on minimum inhibitory concentration (MIC) of sodium hydroxide (NaOH), acetic acid, boric acid, citric acid, maleic acid, hydrochloric acid and sulfuric acid. The MIC values of the respective chemicals were 3.125, 6.25, < 50.0, 25.0, 6.25, 1.56 and 0.781 mg/ml. Except boric acid, the lysis efficiency was reached more than 99.99% at 5 min after treatment of all chemicals. Among those chemicals, NaOH-induced VPGs showed completely DNA-free that was confirmed by quantitative real-time PCR. Besides, lipopolysaccharides (LPS) extracted from the NaOH-induced VPGs showed no distinctive band on SDS-PAGE gel after silver staining. On the other hand, LPS extracted from wild-type bacterial cells as well as the organic acids-induced VPGs showed triple major bands and LPS extracted from the inorganic acids-induced VPGs showed double bands. It suggests that some surface structures in LPS of the NaOH-induced VPGs may be lost, weakened or modified by the MIC of NaOH. Nevertheless, Limulus amoebocyte lysate assay revealed that there is no significant difference in endotoxic activity between the NaOH-induced VPGs and wild-type bacterial cells. Macrophages exposed to the NaOH-induced VPGs at 0.5 × 106 CFU/mL showed cell viability of 97.9%, however the MIC of NaOH did not reduce the cytotoxic effect of wild-type bacterial cells. Like Escherichia coli LPS, the NaOH-induced VPGs are an excellent activator of pro-inflammatory cytokines (IL-1β and iNOS), anti-inflammatory cytokine (IL-10) and dual activities (IL-6) in the stimulated macrophage cells. On the other hand, the induction of TNF-α mRNA was remarkable in the macrophages exposed with wild-type cells. Scanning electron microscopy showed the formation of trans-membrane lysis tunnel structures in the NaOH-induced VPGs. SDS-PAGE and agarose gel electrophoresis also confirmed that cytoplasmic proteins and genomic DNA released from the VPGs to culture medium through the lysis tunnel structures. Taken together, all these results indicated that the NaOH-induced VPGs show the potency of safe, economical and effective inactivated bacterial vaccine candidate.

Semiconductor materials have been shown to have better photocatalytic behavior and can be utilized for the photodegradation of organic pollutants. In this work, three-dimensional flower-like SnS₂ were synthesized by a facile hydrothermal method. Core-shell structured SiO₂@α-Fe₂O₃ nanocomposites were then deposited on the top of the SnS₂ flowers. The as-synthesized nanocomposites were characterized by X-ray diffraction (XRD), Raman spectroscopy, field emission scanning electron microscopy (FE-SEM), Brunauer-Emmett-Teller (BET) and photoluminescence spectroscopy (PL). The photocatalytic behavior of the SnS₂-SiO₂@α-Fe₂O₃ nanocomposites was observed by observing the degradation of methylene blue (MB). The results show an effective enhancement of photocatalytic activity for the degradation of MB especially for the 15 wt. % SiO₂@α-Fe₂O₃ nanocomposites on SnS₂ flowers.

More than 1.1 billion people lack access to electricity in the world, among them 600 million are in sub-Saharan African countries. The socio-economic life of the rural communities is highly affected by electricity supply. The demanding Interest for growth and development in developing countries led to a renewed interest in solar lights. Liter of the night light is a solar-powered light that is constructed from waste plastic bottles which light up the rural community. This paper is about experimental analysis of liter of night light for potential use in rural electrification. The technology uses environmentally friendly and locally available materials. The system is provided with battery storage, which allows it to operate for 13.5 hours continuously at full charge. Solar radiation is converted by PV solar panel to electric current. Circuit board is developed and fabricated to regulate and deliver a consumable amount of voltage by the rechargeable lead-acid battery. After testing five different solutions, the study found out that vinegar solution as the optimal solutions for the technology that can deliver 27lux of light to the surrounding. Simultaneously the study found out, that the light that is emitted from the bottle bulb is a function of volume, depth and solution type. And for this relationship curves are developed. And, the technology can be used for rural communities as it is.

The XChem facility at Diamond Light Source offers fragment screening by X-ray crystallography as a general access user program. The main advantage of X-ray crystallography as a primary fragment screen is that it yields directly the location and pose of the fragment hits, whether within pockets of interest or merely on surface sites: this is the key information for structure-based design and for enabling synthesis of follow-up molecules. Extensive streamlining of the screening experiment at XChem has engendered a very active user programme that is generating large amounts of data: in 2017, 36 academic and industry groups generated 35,000 datasets of uniquely soaked crystals. It has also generated a large number of learnings concerning the main remaining bottleneck, namely obtaining a suitable crystal system that will support a successful fragment screen. Here we discuss the practicalities of generating screen-ready crystals that have useful electron density maps, and how to ensure they will be successfully reproduced and usable at a facility outside the home lab.

Evidence has shown that the state of the patient care environment has a direct impact in heightening the risks of hospital acquired infections among patients admitted in hospitals. And in view of the sub-optimal standard of cleanings by housekeeping staff, the quest for a better approach to reliably disinfect environmental surfaces in healthcare facilities. The ultraviolet light has been known for its antimicrobial property, and have been used in water treatment, food processing and in-duct cleaning of ventilations. A recent introduction of its use for surface decontamination has raised interest among hospitals.However, studies have shown that, in spite of its relative success in other applications, there is doubt in its efficacy in decontaminating shadowed areas of the room, and therefore, would not be seen as justifying its capital intensiveness.

An experimental study is carried out in a cavitation tunnel on a propeller operating downstream of a non-uniform wake. The goal of this work is to establish quantitative correlations between the near pressure field and the cavitation pattern that takes place on the propeller blades. The pressure field is measured at the walls of the test section and in the near wake of the propeller, and is combined with quantitative high-speed image recording of the cavitation pattern. Through simple harmonic analysis of the pressure data and image processing techniques that allow to retrieve the cavitation extension and volume, we discuss the potential sources that generate the pressure fluctuations. Time correlations are unambiguously established between pressure peak fluctuations and cavitation collapse events, based upon the Rayleigh collapse time. Finally, we design a model to predict the cavitation-induced pressure fluctuations from the derivation of the cavitation volume acceleration. This simple model demonstrates a remarkable agreement with the actual pressure field.

Functional Near Infrared Spectroscopy (fNIRS) systems for e-health applications usually suffer of poor signal detection mainly due to a low end-to-end signal to noise ratio of the electronics chain. Lock-In Amplifiers (LIA) historically represent a powerful technique helping to improve performances in such circumstances. In this work it has been designed and implemented a digital LIA system, based on a Zynq® Field Programmable Gate Array (FPGA), trying to explore if this technique might improve fNIRS system performances. More broadly, FPGA based solution flexibility has been investigated, with particular emphasis applied to digital filter parameters, needed in the digital LIA, and it has been evaluated its impact on the final signal detection and noise rejection capability. The realized architecture was a mixed solution between VHDL hardware modules and software ones, running within a softcore microprocessor. Experimental results have shown the goodness of the proposed solutions and comparative details among different implementation will be detailed. Finally a key aspect taken into account throughout the design was its modularity, allowing an ease increase of the input channels while avoiding the growth of the design cost of the electronics system.

In this work, we'll present the power spectra density, auto-correlation function, dentrended fluctuation analysis and multifractal spectrum are performed to the daily light curves of Blazars monitored by Fermi LAT. Some signs of power law are found.

Due to the demands of personal travels and entertainments, light airplanes and small business aircrafts are developing rapidly. Light airplane structure is simple; however, it lacks crashworthiness design, especially the considerations on the impact of energy absorption. Therefore, in an event of accident, significant damage to passengers will be usually incurred. Airplanes made of composite materials structurally have high specific strength and good aerodynamic configuration. These materials have become the primary choice for new airplane development. This study mainly explores the topology optimization analysis of the light aircraft’s cockpit made of carbon fiber reinforced composites. This paper compares the compression amounts in the original models of composite material and aluminum alloy fuselages with the models after optimization during the crash-landing, in order to investigate the safety of fuselages made of different materials after structural optimization under the dynamic crashing. This study found that the energy absorbed by the aluminum alloy fuselage during crash-landing is still higher than that by the carbon fiber reinforced composites fuselage. On the other hand, the aluminum alloy fuselage after topology optimization could have an energy absorption capability enhanced by 40%, as compared to the that of the original model of aluminum alloy fuselage.

An increasing number of aircraft is equipped with wing tip devices, which either are installed by the aircraft manufacturer at the production line or are retrofitted after the delivery of the aircraft to its operator. Installation of wing tip devices has not been a popular choice for regional turboprop aircraft and the novelty of the current study is to investigate the feasibility of retrofitting the British Aerospace (BAe) Jetstream 31 with an appropriate wing tip device (or winglet) to increase its cruise range performance, taking also into account the aerodynamic and structural impact of the implementation. To the best of the knowledge of the authors, no previous study exists which has attempted to assess the winglet retrofit of an existing aircraft type of similar size and operating profile. The optimal winglet design achieved a 2.38% increase of the maximum range by reducing the total drag by 1.19% at a mass penalty of 3.25%, as compared with the baseline aircraft configuration. Other designs were found to be more effective in reducing the total drag, but the structural reinforcement required for their implementation outweighed the achieved performance improvements. Since successful winglet retrofit programs for typical short to medium range narrow body aircraft report even more than 3% of block fuel improvements, undertaking the project of installing an optimal winglet design to the BAe Jetstream 31, should also consider a Direct Operating Cost (DOC) assessment on top of the aerodynamic and structural aspects of the retrofit.

Extracellular vesicle (EV) release, which occurs in most eukaryotic cells, has recently been associated with peptidylarginine deiminase (PAD)-driven protein deimination. Evidence points to the involvement of deiminated cytoskeletal proteins and changes in histone deimination. Both PADs and EVs are associated with various pathologies including cancers, autoimmune and neurodegenerative diseases. The elevated PAD expression observed in cancers may contribute to increase in EV shedding observed from cancer cells, contributing to cancer progression. Similarly, elevated PAD expression observed in neurodegenerative diseases may cause increased EV shedding and spread of neurodegenerative EV cargo, contributing to disease progression and pathologies. Pharmacological inhibition of PAD-mediated deimination using pan-PAD inhibitor Cl-amidine, reduced cellular EV release in prostate cancer cells, rendering them significantly more susceptible to chemotherapeutic drugs. Studies on models of central nervous system damage have demonstrated critical functional roles for PADs and neuroprotective effects using PAD inhibitors in vivo, while human neurodegenerative iPSC in vitro models showed evidence of increased protein deimination. Besides using refined PAD inhibitors to selectively manipulate EV biogenesis for novel combination therapies in cancer treatment, we also speculate how EV biogenesis could be targeted via the newly identified PAD-pathway to ameliorate neurodegenerative disease progression.

Since the recent legalization of medical and recreational use of cannabis (Cannabis sativa L.) in many regions worldwide, there has been high demand for research to improve yield and quality. With the paucity of scientific literature on the topic, this study investigated the relationships between light intensity (LI) and photosynthesis, inflorescence yield, and inflorescence quality of cannabis grown in an indoor environment. After growing vegetatively for 2 weeks under a canopy-level photosynthetic photon flux density (PPFD) of ≈ 425 μmol·m-2·s-1 and an 18-h light/6-h dark photoperiod, plants were grown for 12 weeks in a 12-h light/12-h dark ‘flowering’ photoperiod under canopy-level PPFDs ranging from 120 to 1800 μmol·m-2·s-1 provided by light emitting diodes. Leaf light response curves varied both with localized (i.e., leaf-level) PPFD and temporally, throughout the flowering cycle. Therefore, it was concluded that the leaf light response is not a reliable predictor of whole- plant responses to LI, particularly crop yield. This may be especially evident given that dry inflorescence yield increased linearly with increasing canopy-level PPFD up to 1800 μmol·m-2·s-1, while leaf-level photosynthesis saturated well below 1800 μmol·m-2·s-1. The density of the apical inflorescence and harvest index also increased linearly with increasing LI, resulting in higher-quality marketable tissues and less superfluous tissue to dispose of. There were no LI treatment effects on cannabinoid potency, while there were minor LI treatment effects on terpene potency. Commercial cannabis growers can use these light response models to determine the optimum LI for their production environment to achieve the best economic return; balancing input costs with the commercial value of their cannabis products.

Phytophthora. infestans is a well known late blight causing oomycetes pathogen. It evolves and adapts to the host background and new fungicide molecules rapidly within a few years of their release, may be due to the predominance of transposable elements in its genome. Frequent and huge applications of fungicides cause environmental concerns. Here we developed target specific RNA interference based molecules, that are capable of effectively reducing the late blight infection. cDNA microarray expression data was used for the selection of genes involved in the early stage of infection process, sporulation etc. The in vitro synthesis of double stranded RNA molecule, targeting SDH, EF-1α, GPI-HAM344, PLD-3 and HSP-90 encoding genes revealed the reduction in growth, sporulation and symptom expression, which were subsequently assessed by culture bioassay, detached leaf assay and topical application methods. The multiple genes targeted dsRNA nano clay sprayed plants showed enhanced disease resistance (4% disease severity) and least sporulation (<1x103), compared to naked dsRNA spray. Use of nano clay was assumed to be involved in the effective delivery, protection and boosting the action of RNAi in potato plants. A significant difference in the growth, sporulation count, disease severity and reduced expression of the genes and confocal microscopy imaging authenticates the effects of SIGS on late blight disease progression. Our research demonstrated that topical dsRNA nano clay spray under the open-air environment could be an alternative to chemical fungicides and transgenic approaches as a novel plant protection strategy for late blight in an environmentally friendly manner.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

Mesoporous TiO2/reduced graphene oxide/Ag (TiO2/RGO/Ag) ternary nanocomposite with effective electrons transfer pathway is obtained by an electrostatic self-assembly method and photo-assisted treatment. Compared with bare mesoporous TiO2 (MT) and mesoporous TiO2/RGO (MTG), the ternary mesoporous TiO2/RGO/Ag (MTGA) nanocomposite exhibited superior photocatalytic performance for the degradation of MB under visible light, and the degradation rate reached 0.017 min-1, which was 3.4 times higher than that of MTG. It is proposed that Ag nanoparticles can form the local surface plasmon resonance (LSPR) to absorb the visible light and distract the electrons into MT, and RGO can accept the electrons from MT to accelerate the separation efficiency of carriers. The establishment of MTGA ternary nanocomposite make the three components act synergistic effect to enhance the photocatalytic performance.

In resettlement planning literature, much has been written on economic, land valuation and compensation, infrastructure and services aspects of the land. Psychological risks and stresses of resettled communities, however, have been under-researched. The current research looks at the psychological risks of resettlers in a Development-Induced Displacement and Resettlement (DIDR) project in Sri Lanka. Focusing on the stages of resettlement planning process discussed by Scudder and Colson four-stage model (1980) and the psychological risks discussed by Cernea’s (1990) impoverishment risks and reconstruction (IRR) model. This study evaluates the significant level of the psychological risks faced by the communities in DIDR projects in Sri Lanka relating to before and after resettlement. Moragahakanda Resettlement Project (MRP) was selected as the case study which is located in Naula DS division of Matale District, Central Province, Sri Lanka. A questionnaire survey, documents and field observations were used to evaluate the current psychological risks. The responses received from multiple choice questions were analyzed by Significant Point (SP) index. The research findings point that there are no conspicuous changes of psychological risks related to before/after resettlement has occurred in re-settlers. The findings highlight that the psychological risk levels in transition stage have remained the same level in the potential development stage. This research provides a systematic guidance enabling the physical planners to prioritize the most significant psychological risks which should be considered in the decision-making process of DIDR projects.

Blazars show rapid and high amplitude variability. In this work , Fermi daily light curve of 130 sources are analyzed, distribution of daily variability are compared with each other by using Kolmogorov-Smirnov (K-S) test. results show: 1)Some pairs of the distributions are similar; 2) In most cases, the distributions are not Gaussian.

We use earthquake ground motion modelling via Ground Motion Prediction Equations (GMPEs) and numerical simulation of seismic waves to consider the effects of site amplification and basin resonance in Jakarta, the capital city of Indonesia. While spectral accelerations at short periods are sensitive to near-surface conditions (i.e., Vs30), our results suggest that, for basins as deep as Jakarta’s, available GMPEs cannot be relied upon to accurately estimate the effect of basin depth on ground motions at long periods (>1 s). Amplitudes at such long periods are influenced by entrapment of seismic waves in the basin, resulting in longer duration of strong ground motion, and interference between incoming and reflected waves as well as focusing at basin edges may amplify seismic waves. In order to simulate such phenomena in detail, a basin model derived from a previous study is used as a computational domain for deterministic earthquake scenario modeling in a 2-dimensional cross-section. A M_w 9.0 megathrust, a M_w 6.5 crustal thrust and a M_w 7.0 instraslab earthquake are chosen as scenario events that pose credible threats to Jakarta, and the interactions with the basin of seismic waves generated by these events were simulated. The highest PGV amplifications are recorded at sites near the middle of the basin and near its southern edge, with maximum amplifications of PGV in the horizontal component of 200% for the crustal, 600% for the megathrust and 335% for the deep intraslab earthquake scenario, respectively. We find that the levels of ground motion response spectral acceleration fall below those of the 2012 Indonesian building Codes's design response spectrum for short periods (< 1 s), but closely approach or may even exceed these levels for longer periods.

We overview recent progress in growth aspects of group III-nitride heterostructures for deep ultraviolet (DUV) light-emitting diodes (LEDs), with particular emphasis on the growth approaches for attaining high-quality AlN and high Al-molar fraction AlGaN. The discussion commences with the introduction of the current status of group III-nitride DUV LEDs and the remaining challenges. This segues into discussion of LED designs enabling high device performance followed by the review of advances in the methods for the growth of bulk single crystal AlN intended as a native substrate together with a discussion of its UV transparency. It should be stated, however, that due to the high-cost of bulk AlN substrates at the time of this writing, the growth of DUV LEDs on foreign substrates such as sapphire still dominates the field. On the deposition front, the heteroepitaxial growth approaches incorporate high-temperature metal organic chemical vapor deposition (MOCVD) and pulsed-flow growth, a variant of MOCVD, with the overarching goal of enhancing adatom surface mobility, and thus epitaxial lateral overgrowth which culminates in minimization the effect of lattice- and thermal-mismatches. This is followed by addressing the benefits of pseudomorphic growth of strained high Al-molar fraction AlGaN on AlN. Finally, methods utilized to enhance both p- and n-type conductivity of high Al-molar fraction AlGaN are reviewed.

Fast neutron (FN) radiation mediated mutagenesis is a unique approach among the several induced mutagenesis methods being used in plant science in terms of impacted mutations. The FN mutagenesis usually creates deletions from a few bases to several million bases (Mb). A library of random deletion generated using FN mutagenesis lines can provide indispensable resources for the reverse genetic approaches. In this review, information from several efforts made using FN mutagenesis has been compiled to understand the type of induced mutations, frequency, and genetic stability. Concerns regarding the utilization of FN mutagenesis technique for a plant with different level of ploidy and genome complexity are discussed. We have highlighted the utility of next-generation sequencing techniques which can be efficiently utilized for the characterization of mutant lines as well as for the mapping of causal mutations. Pros and cons of Mut-map, MutChromSeq, exon capture, whole genome sequencing, MutRen-Seq, and different tilling approaches can be used for the detection of FN-induced mutation has also been discussed. Genomic resources developed using the FN mutagenesis have been catalogued wooing to meaningful utilization of the available resources. The information provided here will be helpful for the efficient exploration for the crop improvement programs and for better understanding of genetic regulations.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

A tailored model for the assessment of environmental benefits achievable by “light-weighting” in the automotive field is presented. The model is based on the Fuel Reduction Value (FRV) coefficient, which expresses the Fuel Consumption (FC) saving involved by a 100 kg mass reduction. The work is composed of two main sections: simulation and environmental modelling. Simulation modelling performs an in-depth calculation of weight-induced FC whose outcome is the FRV evaluated for a wide range of Diesel Turbocharged (DT) vehicle case studies. Environmental modelling converts fuel saving to impact reduction basing on the FRVs obtained by simulations. Results show that for the considered case studies, FRV is within the range 0.115–0.143 and 0.142–0.388 L/100 km × 100 kg, respectively, for mass reduction only and powertrain adaptation (secondary effects). The implementation of FRVs within the environmental modelling represents the added value of the research and makes the model a valuable tool for application to real case studies of automotive lightweight LCA.

In this study, the problem of overcoming the infinite energy barrier separating the bradyonic and tachyonic realms is investigated. Making use of the Majorana equation for particles with arbitrary spin and the Heisenberg uncertainty principle, it is proved that, under certain conditions of spatial confinement, quantum fluctuations allow particles with very small mass and velocity close to the speed of light to pass in the tachyonic realm, avoiding the problem of the infinite barrier (bradyon–tachyon tunnelling). This theoretical approach allows an avoidance of the difficulties encountered in quantum field theory when it is extended to particles with imaginary rest mass.

This work communicates results from optical emission spectroscopy following laser-induced optical breakdown at or near nanomaterial. Selected atomic lines of silver are evaluated for consistent determination of electron density. Comparisons are presented with Balmer series hydrogen results. Of particular interest are measurements free of self-absorption effects. For several silver lines, asymmetries are observed in the recorded line profiles. Electron densities of interest range from 0.5 to 3 × 10¹⁷ cm^-3, for 5 nanosecond Q-switched Nd:YAG radiation at wavelengths of 1064, 532, and 355 nm, and for selected silver emission lines including 328.0, 338.2, 768.7, and 827.3 nm, and the hydrogen alpha Balmer series line at 656.3 nm. Line asymmetries are presented for the 328.0 nm Ag I line that is measured following generation of the plasma due to multiple photon absorption. This work explores electron density variations for different irradiance levels, and reports spectral line asymmetry of resonance lines for different laser fluence levels.

Three-dimensional (3D) imaging has attracted more and more interests because of its widespread applications, especially in information and life science. These techniques can be broadly divided into two types: ray-based and wavefront-based 3D imaging. Issues such as imaging quality and system complexity of these techniques limit the applications significantly, and therefore many investigations have focused on 3D imaging from depth measurements. This paper presents an overview of 3D imaging from depth measurements, and provides a summary of the connection between these the ray-based and wavefront-based 3D imaging techniques.

Rice grassy stunt virus (RGSV) a member of Tenuivirus family, is very potent and destructive which effects rice crop in many countries, particularly China. Non coding RNAs have important functions in development and epigenetic regulation of gene expression in numerous organsisms. There is three type of small non coding RNAs have been found in eukaryotes, which are small interferring RNAs (siRNAs), microRNAs (miRNAs) and piwi interacting RNAs (piRNAs). Small RNAs (sRNAs) origination is from the infecting virus which is known as virus-derived small interfering RNAs (vsiRNAs), has responsibility for RNA silencing in plants. Virus-induced gene silencing (VIGS) is mainly dependent on RNA silencing (RNAi). Interestingly, RNA silencing happens in plants during viral infections. RNAi technique showed significant results in Nephotettix cincticeps. RNAi technique demonstrated the gene silencing of planthopper Nilaparvata lugens. The proteins P5, pcf4, Dnj, psn5, and pn6 act as potential movement proteins and serve as silencing suppressors for RGSV. VsiRNAs originate from dsRNA molecules which require Dicer-like (DCL) proteins, RNA dependent RNA polymerase (RdRP) proteins, and Argonaute (AGO) proteins. RdRP uses ssRNA for perfect RNA amplification process and can also be used for DCL dependent secondary vsiRNA formation. VSRs interfere with the movement of signals during silencing mechanism. Moreover, intercellular movement of viruses is facilitated by virus-encoded movement protein. RNAi is found in many eukaryotes which are related to transcriptional or post-transcriptional regulation by gene suppression. Transcription is bidirectional in ssDNA viruses which are originated from dsRNA molecules. In this review, we highlighted the biology of Rice grassy stunt virus and its insect vector and its silencing suppressors. This work will be helpful for plant virologists to understand the whole biogenesis mechanism for rice viruses especially RGSV.

In this study, we evaluated chlorophyll fluorescence (CF) under two extreme illumination conditions at plant scale with a passive spectroradiometer. Fluorescence (F) was estimated by reading directly from radiance spectra of a variety of plants illuminated with light-emitting diode (LED) grow lights in the laboratory. Solar-induced fluorescence (SIF) was estimated from spectral measurements of the same plants under sunlight using the Fraunhofer Line Depth (FLD) method. Chlorophyll fluorescence yield (F_yield) and solar-induced fluorescence yield (SIF_yield) were calculated by normalizing F and SIF with absorbed photosynthetically active radiation (APAR). Two approaches to estimating APAR were compared: utilizing white reference spectra and reflected spectra versus white reference spectra combined with the fraction of absorbed photosynthetically active radiation (fPAR) derived from literature. Average F and SIF were different by a factor of approximately twenty-four (F = 0.110 ± 0.038 Wm⁻²μm⁻¹sr⁻¹ versus SIF = 2.60 ± 1.87 Wm⁻²μm⁻¹sr⁻¹). In contrast, the average normalized values F_yield and SIF_yield were within the margin of error of one another (F_yield = 0.022 ± 0.008 μm⁻¹sr⁻¹ and SIF_yield = 0.030 ± 0.020 μm⁻¹sr⁻¹). This study highlights the influence of APAR on CF and the importance of properly accounting for it when estimating yield and demonstrates the ability of two simple and portable experimental setups with a passive instrument to obtain fluorescence metrics.

Outdoor lighting is becoming increasingly widespread, and residents are suffering from serious light pollution as a result. Residents’ awareness of their rights to protection has gradually increased. However, due to the sometimes-inaccessible nature of residential vertical light incidence intensity data and the high cost of obtaining specific measurements, there is no appropriate hierarchic compensation for residents suffering from different degrees of light pollution. It is therefore important to measure light pollution levels and their damage at the neighborhood scale to provide residents with basic materials for proper protection and to create more politically suitable solutions. This article presents a light pollution assessment method that is easy to perform, is low-cost, and has a short data-processing cycle. This method can be used to monitor residential zone light pollution in other cities. We chose three open areas to test the spatial variation pattern of light intensity. The results are in accordance with spatial interpolation patterns and can be fit, with high precision, using the IDW method. This approach can also be used in 3 dimensions to quantitatively evaluate the distribution of light intensity distribution. We use a mixed-use zone in Beijing known as The Place as our case study area. The vertical illumination at the windows of residential buildings ranges from 2 lux to 23 lux; the illumination in some areas is far higher than the value recommended by CIE. Such severe light pollution can seriously interfere with people's daily lives and has a serious influence on their rest and health. The results of this survey will serve as an important database to assess whether the planning of night-time lighting is scientific and whether it provides residents with a basis for the protection of their rights.

Background: The morbidity of myocardial infarction is keeping raise in this decade. Because of high safety and operability , percutaneous coronary intervention(PCI) has been used to conquer this disease for more than 20 years.An important complication of PCI is contrast induced nephropathy(CIN), which raises our attention. Previously, we started a study to explore the correlation between acute kidney injury and myonecrosis after scheduled percutaneous coronary intervention. Our study showed that the rate of CI-AKI in patients with post-procedural myocardial injury and undergoing elective PCI was higher than that in patients free of injury. Methods: In this study,forty male rats were randomly divided into four groups: control group (n=8), CM group (n=12), AMI group (n=8) and AMI+CM group (n=12), then velocity of renal artery blood flow (VRABF), computer tomography (CT), serum creatinine(Scr), reactive oxidative species (ROS), periodic acid-Schiff (PAS) and TUNEL were used to estimate the injury of kidney. We analyzed 327 non-ST-segment elevation acute coronary syndrome subjects undertaking elective PCI. Serum levels of creatinine (SCr) and the eGFR before coronary angiography, and 24–72 h after contrast administration were recorded to assess the renal function. Results: The data showed that VRABF was lower in AMI+CM group than CM group from 0 minute to 24h and CT number in cortex was higher in AMI+CM group than CM group at 4-hour. As well as the level of Scr in AMI+CM group displayed a significantly increase at 24-hour compared with CM group. The histopathologic scores and percentage of tubular cell apoptosis were higher in AMI+CM group at 24-hour. In 327 patients, we found that CI-AKI occurred more often in subjects with post-procedural myonecrosis (PMN) than in those without PMN (20.8% versus 5.8%, respectively, P=0.001). Conclusion: Compared to the elective patient, the injury of CIN exhibited a higher severity in AMI patient.

There is a growing interest in fibers supporting optoelectrical properties for textile and wearable display applications. Solution-processed electroluminescent (EL) material systems can be continuously deposited onto fiber or yarn substrates in a roll-to-roll process, making it easy to scale manufacturing. It is important to have precise control over layer deposition to achieve uniform and reliable light emission from these EL fibers. Slot-die coating offers this control and increases the rate of EL fiber production. Here, we report a highly adaptable, cost-effective 3D printing model for developing slot dies used in automatic coating systems. The resulting slot-die coating system enables rapid, reliable production of alternating current powder-based EL (ACPEL) fibers and can be adapted for many material systems. The benefits of this system over dip-coating for roll-to-roll production of EL fibers are demonstrated in this work.

The halotolerant microalga Dunaliella salina has been widely studied for natural β-carotene production. This work shows biochemical characterization of three newly isolated Dunaliella salina strains DF15, DF17 and DF40 compared with D. salina CCAP 19/30 (confirmed to be D. tertiolecta) and D. salina UTEX 2538 (also known as D. bardawil). Although all three new strains have been genetically characterized as Dunaliella salina strains, their ability to accumulate carotenoids and their capacity for photoprotection against high light stress are different. DF15 and UTEX 2538 reveal great potential for producing large amount of β-carotene and maintained a high rate of photosynthesis under light of high intensity; however, DF17, DF40 and CCAP 19/30 showed increasing photoinhibition with increasing light intensity, and reduced contents of carotenoids, in particular b-carotene, suggesting that the capacity of photoprotection is dependent on the cellular content of carotenoids, in particular β-carotene. Strong positive correlations were found between the cellular content of each of all-trans β-carotene, 9-cis β-carotene, all-trans α-carotene and zeaxanthin but not lutein in the D. salina strains. Lutein was strongly correlated with respiration in photosynthetic cells and strongly related to photosynthesis, chlorophyll and respiration, suggesting an important and not hitherto identified role for lutein in co-ordinated control of the cellular functions of photosynthesis and respiration in response to changes in light conditions, which is broadly conserved in Dunaliella strains. Statistical analysis based on biochemical data revealed a different grouping strategy from the genetic classification of the strains. The significance of these data for strain selection for commercial carotenoid production is discussed.

The monitoring of sick newborns is a challenging task that health care providers in Neonatal Intensive Care Units (NICU) must contend with each day. Conventionally, newborns are monitored via probes that are affixed to their skin and attached to processing monitors (Fig.1). However, an alternative exists in contactless imaging to record such physiological signals (Physio-Markers), surface changes and internal structures which can be used independently of, or in conjunction with conventional monitors. Advantages of contactless monitoring methods include: i) quick data generation; ii) lack of contact with skin, which reduces skin breakdown and decreases risk of infection; and iii) minimizing the number of probes and monitors affixed to the skin, which allows greater body surface-area for other care. This paper is an attempt to build a foundation for and to provide a vision of the potential neonatal clinical applications of technologies that use non-contact modalities such as Visible Light Imaging (VLI), Near InfraRed Spectrum (NIRS), and Thermal Imaging (TI) using InfraRed Spectrum (IRS).

Although the vegetative stage of indoor cannabis production can be relatively short in duration, there is a high energy demand due to higher light intensities (LI) than the clonal propagation stage and longer photoperiods than the flowering stage (i.e., 16 – 24 hours vs. 12 hours). While electric lighting is a major component of both energy consumption and overall production costs, there is a lack of scientific information to guide cultivators in selecting a LI that corresponds to their vegetative stage production strategies. To determine the vegetative plant responses to LI, clonal plants of ‘Gelato’ were grown for 21 days with canopy-level photosynthetic photon flux densities (PPFD) ranging between 135 and 1430 µmol·m^-2·s^-1 on a 16-hour photoperiod (i.e., daily light integrals of ≈ 8 to 80 mol·m^-2·d^-1). Plant height and growth index responded quadratically; the number of nodes, stem thickness, and aboveground dry weight increased asymptotically; and internode length and water content of aboveground tissues decreased linearly with increasing LI. Foliar attributes had varying responses to LI. Chlorophyll content index increased asymptotically, leaf size decreased linearly and specific leaf weight increased linearly with increasing LI. Generally, PPFD levels of ≈ 900 µmol·m^-2·s^-1 produced compact, robust plants that are commercially relevant, while PPFD levels of ≈ 600 µmol·m^-2·s^-1 promoted plant morphology with more open architecture – to increase airflow and reduce the potential foliar pests in compact (i.e., indica-dominant) genotypes.

The new coronavirus (2019-nCoV) in Wuhan has caused virus outbreaks in many provinces and cities in China, and several neighboring countries were also affected. In recent years, coronavirus several outbreaks around the world were reported, however researchers could not predict its onset. Coincidentally, the birthplace of another coronavirus (SARS-CoV) that causes serious public health problems is also in China. This review compares and analyzes the external environment, natural hosts, intermediate hosts, and susceptible populations when these two coronaviruses occurred. Based on the analysis results, we found that the 2019-nCov virus outbreak in Wuhan was not an accidental phenomenon, but a result of a combination of factors. At the same time, through the conclusions of these analyses, we will be able to get a glimpse of the trajectories of new coronaviruses and curb the virus outbreak in future.

Today, transit control systems go beyond simple controllers located at the intersections of our streets, involving large companies in the field, which with the implementation and use of sophisticated equipment encompass endless new and advanced technologies that manage to give control to the massive automotive park, thus ensuring fluidity and road safety. Many of these systems are used in the big world capitals, which is why the model used in Santiago, Chile is a system applied and brought directly by the SIEMENS Company of England (specifically the system used in the City of London). It is capable of transmitting the different control signals in a similar and digital way from the different interconnected devices in and out of the road infrastructure.

Signal-to-noise ratio (SNR) is an important index to evaluate radiation performance and image quality of optical imaging systems under low illumination background. Under the nighttime lighting condition, the illumination of remote sensing objects is low and varies greatly, usually ranging from several lux to tens of thousands of lux. Nighttime light remote sensing imaging requires high sensitivity and large dynamic range of detectors. Luojia 1-01 is the first professional nighttime light remote sensing satellite in the world. In this paper, we took the nighttime light remote sensing camera carried on the satellite as research object, proposed an in-orbit SNR test method based on time series images to overcome the problem of low spatial resolution. We first analyzed the process of luminous flux transmission between objects and satellite and established a radiative transfer model. By combining the parameters of large relative aperture optical system and high sensitivity CMOS device, we established SNR model and specially analyzed the effect of exposure time and quantization bits on SNR. Finally we used the proposed in-orbit test method to calculate SNR of lighting images acquired by satellite. And the measured result is in good agreement with the model predicted data. Under the condition of 10lx illumination, the SNR of typical objects can reach 27.02dB, which is much better than the requirement of 20dB for engineering application.

Cyanobacteria are extensively studied and cultured because they can produce many value-added substances among which are pigments, mainly the phycobiliproteins phycocyanin (PC), phycoerythrin (PE), allophycocyanin (APC) and chlorophyll-a and carotenoids as well. As numerous cyanobacterial species await optimization for maximizing pigment production, we examined here two local marine species, Phormidium sp. and Cyanothece sp. batch cultured under 18-19.5 oC, at 40 ppt salinity with Walne’s nutrient medium, using white LED light of low (2000 lux) and high (8000 lux) intensity and additionally blue, green and red LED light. Significant differences were found among the intensities and colors of light used. Maximum growth was induced by high white light in both species (2.15 g dw/L in Phormidium and 1.47 g/L in Cyanothece). Next to them was green light (1.25 g/L) in Cyanothece and low white and green (1.26 – 1.33 g/L) in Phormidium. Green light maximized phycocyanin content in Phormidium (0.45 mg/mL), while phycoerythrin was maximized (0.17 mg/mL) by blue light and allophycocyanin by all colors (~0.80 mg/mL). All colors maximized phycocyanin in Cyanothece (~0.32 mg/mL) while phycoerythrin and allophycocyanin were maximized under green light (~0.138 and 0.38 mg/mL respectively). In Phormidium maximization of chlorophyll-a (9.3 μg/mL) was induced by green light while total carotenoids and b-carotene (3.05 and 0.89 μg/mL respectively) by high white light. In Cyanothece both white light intensities along with green light maximized chlorophyll-a content (~9 μg/mL) while high white light and green maximized total carotenoids (2.6-3.0 μg/mL).

A metastable β-Ti alloy, Ti–10V–3Fe–3Al (wt.%), was subjected to thermos-mechanical processing including the compression test at 725°C, which is below the β transus temperature (780°C), and at strain rate of 10-3s-1. The presence of phases was determined using transmission electron microscopy and X-ray diffraction. Although the dynamic recovery took place together with slip, both deformation-induced α˝ martensite and ω were detected as other operating mechanisms for the first time in metastable-β Ti alloys deformed in α+β region. The volume fraction of stress-induced α˝ was higher than that of the same alloy deformed at room temperature due to higher strain applied. Stress-induced twinning was not operational, which could be related to the priority of slip mechanism at high temperature resulted from thermally-assisted nucleation and lateral migration of kink-pairs.

In this work, an energy-saving smart light controlling system has been proposed that can main-tain the desired intensity of light in a room automatically. Unlike the conventional light control system, the proposed system splits a large room into several zones and analyzes the light inten-sity of each zone; hence, the controlling unit adjusts the light intensity to the desired level. The main controlling unit consists of a light sensor, a motion sensor, a relay with a driver unit, an LCD display, etc. for controlling light efficiently to reduce the power waste. The sensors meas-ure the intensity of light, based on the standard light intensity data chart the controller units make a decision how many light bulbs are needed to be switched ON/OFF in a particular zone. Moreover, the system automatically switched-OFF all light bulbs when there is nobody in the room. Proteus design suite 8.0 is used to design and simulation of the proposed system. Moreo-ver, the PCB layout is designed using ExpressPCB version 7.5.0. The proposed system is capable of minimizing the power loss by up to 44% in comparison to the conventional light manage-ment system.

In order to reach the theoretical efficiency limits of lead-based metal halide perovskite solar cells, the voltage should be enhanced because it suffers from nonradiative recombination. Perovskite materials contain intrinsic defects that can act as Shockley-Read-Hall recombination centers. Several experimental and computational studies have characterized such defect states within the band gap. We give a systematic overview of compositional engineering by distinguishing the different defect reducing mechanisms. Doping effects are divided into influences on: (1) Crystallization; (2) Lattice properties. Incorporation of dopant influences the lattice properties by: (a) Lattice strain relaxation; (b) Chemical bonding enhancement; (c) Band gap tuning. The intrinsic lattice strain in undoped perovskite was shown to induce vacancy formation. The incorporation of smaller ions, such as Cl, F and Cd, increases the energy for vacancy formation. Zn doping is reported to induce strain relaxation but also to enhance the chemical bonding. The combination of computational studies using (DFT) calculations quantifying and qualifying the defect reducing propensities of different dopants with experimental studies is essential for deeper understanding and unraveling insights, such as the dynamics of iodine vacancies and the photochemistry of the iodine interstitials, and can eventually lead to a more rational approach in the search for optimal photovoltaic materials.

External quantum efficiency of industrial-grade green InGaN light-emitting diodes (LEDs) has been measured in a wide range of operating currents at various temperatures from 13 K to 300 K. Unlike blue LEDs, the efficiency as a function of current is found to have a multi-peak character, which could not be fitted by a simple ABC-model. This observation correlated with splitting of LED emission spectra into two peaks at certain currents. The characterization data are interpreted in terms of non-uniformity of the LED active region, which is tentatively attributed to extended defects like V-pits. We suggest a new approach to evaluation of temperature-dependent light extraction and internal quantum efficiencies taking into account the active region non-uniformity. As a result, the temperature dependence of light extraction and internal quantum efficiencies have been evaluated in the temperature range mentioned above and compared with those of blue LEDs.

This paper describe the influence of the Rift Molango during the mineralization of elements of the platinum group and some light rare earths elements in a sedimentary exhalative ore deposit.

Our previous in vitro reports showed that crude extract prepared with 50% ethanol (ethanol crude extract, ECE) from Mongolian oak cups possessed excellent antioxidant capacities as well as inhibitory activities against α-glucosidase, α-amylase and protein glycation caused by its enrichment in phenolics, including mainly ellagic acid, kaempferol and their derivatives. Nevertheless, few in vivo studies on antidiabetic activities of these phenolics were conducted. The present study investigated hypoglycemic effects with normal and diabetic rats being administrated orally without or with ECE at 200 and 800 mg/kg for 15 days. In normal rats, no significant differences were exhibited after ECE administration in body weight, fasting blood glucose level, levels of chelesterol, triglyceride, LDL and AST in serum, organ indexes, and levels of GSH and MDA in organs. In diabetic rats, the fasting blood glucose level, indexes of heart and liver, and levels of chelesterol and triglyceride in serum and MDA in heart tissue were significantly decreased. Moreover, HDL levels in serum and SOD activities in the four organs of diabetic rats were significantly improved after ECE administration at 800 mg/kg. Thus, in addition to inhibiting α-glucosidase, α-amylase and protein glycation reported previously, oak cups might contain novel dietary phytonutrients in preventing abnormal changes in blood glucose and lipid profile and attenuating oxidant stress in vivo. The results also implied that it is ellagic acid, kaempferol and their derivatives enriched in ECE that might play vital roles in managing type 1 as well as type 2 diabetes.

Traditional winglets are designed as fixed devices attached at the tips of the wings. The primary purpose of the winglets is to reduce the lift-induced drag, therefore improving aircraft performance and fuel efficiency. However, because winglets are fixed surfaces, they cannot be used to control lift-induced drag reductions or to obtain the largest lift-induced drag reductions at different flight conditions (take-off, climb, cruise, loitering, descent, approach, landing, and so on). In this work, we propose the use of variable cant angle winglets which could potentially allow aircraft to get the best all-around performance (in terms of lift-induced drag reduction), at different flight phases. By using computational fluid dynamics, we study the influence of the winglet cant angle and sweep angle on the performance of a benchmark wing at Mach numbers of 0.3 and 0.8395. The results obtained demonstrate that by adjusting the cant angle, the aerodynamic performance can be improved at different flight conditions.

It is important to distinguish between natural earthquakes and those induced by CO2 injection at carbon capture and storage sites. For example, the 2004 Mw 6.8 Chuetsu earthquake occurred close to the Nagaoka CO2 storage site during gas injection, but we could not quantify whether the earthquake was due to CO2 injection or not. Here we simulated changes of pore pressure during CO2 injection at the Nagaoka site and compared them with estimated natural seasonal fluctuations of pore pressure due to rainfall and snowmelt as well as estimated pore pressure increases related to remote earthquakes. We clearly distinguished changes of pore pressure due to CO2 injection from those due to rainfall and snowmelt. The simulated local increase in pore pressure at seismogenic fault area was much less than the seasonal fluctuations related to precipitation and increases caused by remote earthquakes, and the lateral extent of pore pressure increase was insufficient to influence seismogenic faults. We also demonstrated that pore pressure changes due to distant earthquakes are capable of triggering slip on seismogenic faults. The approach we developed could be used to distinguish natural from injection-induced earthquakes and will be useful for that purpose at other CO2 sequestration sites.

Ionizing radiation-induced bystander effects (RIBE) encompass a number of effects with potential for a plethora of damages in adjacent non-irradiated tissue. The cascade of molecular events is initiated in response to the exposure to ionizing radiation (IR), something that may occur during diagnostic or therapeutic medical applications. In order to better investigate these complex response mechanisms, we employed a unified framework integrating statistical microarray analysis, signal normalization and translational bioinformatics functional analysis techniques. This approach was applied to several microarray datasets from Gene Expression Omnibus (GEO) related to RIBE. The analysis produced lists of differentially expressed genes, contrasting bystander and irradiated samples versus sham-irradiated controls. Furthermore, comparative molecular analysis through BioInfoMiner, which integrates advanced statistical enrichment and prioritization methodologies, revealed discrete biological processes, at the cellular level. For example, negative regulation of growth, cellular response to Zn2+- Cd2+, Wnt and NIK/NF-kappaB signalling, which refine the description of the phenotypic landscape of RIBE. Our results provide a more solid understanding of RIBE cell-specific response patterns, especially in the case of high-LET radiations like α-particles and carbon-ions.

In this paper, we proposed a novel saddle type FinFET (S-FinFET) to effectively solve problems occurring under the capacitor node of dynamic random-access memory (DRAM) cell and showed how its structure was superior to conventional S-FinFETs in terms of short channel effect (SCE), subthreshold slope (SS), and gate-induced drain leakage (GIDL). The proposed FinFET exhibited 4 times lower Ioff than modified S-FinFET called RFinFET with more improved DIBL characteristics while minimizing Ion reduction compared to RFinFET. Our results also confirmed that the proposed device showed improved DIBL and Ioff characteristics as gate channel length decreased.

The variation of photonic orbital angular momentum at Compton scattering is characterized. We determine scattering matrix of a twisted light based on the fundamental conservation of orbital angular momenta. Numerical values for two different twisted light modes: Laguerre Gaussian and Bessel Gaussian, are generated and illustrated. Our analysis indicate that states of photonic orbital angular momentum are highly changeable at wide angle scattering but more consistent at small angle scattering.

During the COVID-19 pandemic face masks grew in importance as their use by the general population was recommended by health officials in order to minimize the risk of infection and prevent further spread of the virus. To ensure health protection of medical personal and other system relevant staff, it is of considerable interest to quickly test if a certain lot of filtering facepiece masks meets the requirements or if the permeability changes under different conditions. As certified penetrometers are rather expensive and were difficult to obtain during the COVID-19 pandemic, we describe two quite simple and cheap methods to quickly test the filter permeability based on an electronic cigarette. The first method uses a precision scale, the second method uses a light scattering detector to measure the filter penetration. To make sure these two methods yield reliable results, both were tested with freshly cut filter samples covering the range of approx. 7% to 60% permeability and compared to the results of a certified penetrometer. The comparison of the two methods with the certified penetrometer showed a good correlation and therefore allow a quick and rather reliable estimation of the permeability. Several examples about the use of faulty masks and the resulting health risks show that simple, fast, cheap and broadly available methods for filter characterization might be useful in these days.

The transmission of light is one of the key optical processes in the terrestrial environment (the atmosphere and underlying surfaces). The dependence of light transmittance on the illumination/observation conditions and optical properties of the atmosphere–underlying system can be studied using the integro-differential radiative transfer equation. However, for numerous applications a set of analytical equations is needed to describe the transmitted light intensity and flux. In this paper, we describe various analytical techniques to study light transmittance through light scattering and absorbing media. A physical significance and improved mathematical accuracy of approximations are provided using the analytical models for the diffusion exponent, average cosine of the light field, spherical and plane albedos. The accuracy of various approximations is studied using exact radiative transfer calculations with various scattering phase functions, single-scattering albedos, observational conditions, and optical depths.

Background: Drug incorporated in hair are exposed to the environment and to cosmetic and chemical treatments, with possible decrease of their content. Knowledge concerning the effect of sun light on drug content in hair can be helpful to the forensic toxicologist, in particular when investigating on drug concentrations above or below pre-determined cut-offs. Materials and Methods: Twenty authentic positive hair samples were selected that had previously tested positive for amphetamines and/or ketamine. Washed hairs were divided into two identical strands: the former was exposed at 765 W/m² (310–800 nm spectrum of irradiance) for 48 hours in a solar simulator, the latter was kept in the dark. Hair samples were extracted and analyzed by LC-HRMS detection. The percent photodegradation was calculated for each analyte (amphetamine, methamphetamine, methylendioxyamphetamine methylendioxymethamphetamine, ketamine, norketamine). In parallel, photodegradation processes of standard molecules dissolved in aqueous and organic solutions were studied. Results: In 20 hair samples positive for the targeted analytes, exposure to artificial sun light induced an appreciable decrease of drug concentrations. The concentration ranges in the non-irradiated hair samples were 0.01–24 ng/mg; 65% of samples exhibited a decrease in post-irradiation samples, with reduction from 3% to 100%. When more drugs were present in the same hair sample (e.g, MDMA and ketamine) the degradation yields were compound dependent. A degradation product induced by irradiation of ketamine in aqueous and methanol solutions was identified; it was also found to be present in a true positive hair sample after irradiation. Conclusions: Ketamine, amphetamines and their metabolites incorporated in hair of drug users undergo degradation when irradiated by artificial sunlight. Only for ketamine a photoproduct was identified in irradiated standard solutions and in true positive irradiated hair. When decisional cut-offs are applied to hair analysis, photodegradation must be taken into account since sunlight may produce false negative results. Moreover, new markers could be investigated as evidence of illicit drug use.

Uniform illumination is a key requirement in different research fields. However, this requirement is often difficult to achieve when high intensity is required at the same time. Recent advancements in LED lamps allow nowadays for compact and economical solutions. In this work we present a suitable solution for various laboratory purposes requiring stable, uniform and high intensity illumination. The system is composed of four identical high power white LED arrays of 30 mm diameter each, placed on a supporting and cooling structure having a minimum volume of 26 cm x 26 cm x 8 cm. A numerical model has been developed, based on a ray tracing software, in order to simulate the performances. These have then been experimentally validated with measurements of the power density map, carried out with a 1% uncertainty pyranometer. Data show that the built system is very stable over time and provides an illumination uniformity higher than 98%, on a surface of 50 mm radius, which reduces to 95% on a surface of 75 mm radius. The power density can be adjusted in the 390-1360 W m-2 range, not affecting uniformity.

Almost all modern inorganic light-emitting diode (LED) designs are based on double heterojunctions (DHJs) whose structure and current injection principle have remained essentially unchanged for decades. Although highly efficient devices based on the DHJ design have been developed and commercialized for energy-efficient general lighting, the conventional DHJ design requires burying the active region (AR) inside a pn-junction. This has hindered the development of emitters utilizing nanostructured ARs located close to device surfaces such as nanowires or surface quantum wells. Modern DHJ III-N LEDs also exhibit resistive losses which arise from the DHJ device geometry. The recently introduced diffusion-driven charge transport (DDCT) emitter design offers a novel way to transport charge carriers to unconventionally placed ARs. In a DDCT device, the AR is located apart from the pn-junction and the charge carriers are injected into the AR by bipolar diffusion. This device design allows the integration of surface ARs to semiconductor LEDs and offers a promising method to reduce resistive losses in high power devices. In this work, we present a review of the recent progress in gallium nitride (GaN) based DDCT devices, and an outlook of potential DDCT has for opto- and microelectronics.

Transferring in vitro-cultured Eustoma seedlings to an ex vitro condition (acclimation) is a big challenge that may expose the seedlings to biotic and abiotic stresses, and affect the internal and external structure of the plants. In addition, in vitro-cultured seedlings of Eustoma are difficult to handle and phenotype and physiological traits such as survival and rosette rate may have altered in the acclimation stage. Therefore, the present study aims to examine the effects of blue, red, and white LED light on the growth and development ex vitro of in vitro-cultured seedlings of Eustoma. The results showed that blue LEDs resulted in greater plant height, internode length, and leaf number, increased upper and lower fresh biomass, and higher chlorophyll content compared with treatment by the other LED lights. Higher stomatal density on the abaxial leaf surface was also observed in the blue LED-treated plants, which also showed a higher survival rate and lower rosette rate. In contrast, the white LED-treated plants had the highest leaf width and internode diameter. Acclimation of the Eustoma plants ex vitro suggests that a combination of blue and white LEDs may be advantageous for better growth and development for large-scale production in a controlled environment.

The Munich ChronoType Questionnaire (MCTQ) has now been available for more than 15 years; its original publication has been cited 1,240 times (Google Scholar, May 2019); its online version, which was available until July 2017, has produced almost 300,000 entries from all over the world (MCTQ database). The MCTQ has gone through several versions, has been translated into 13 languages and has been validated against other more objective measures of daily timing in several independent studies. Besides being used as a method to correlate circadian features of human biology with other factors – ranging from health issues to geographical factors – the MCTQ gave rise to quantifying old wisdoms, like “teenagers are late” and has produced new concepts, like social jetlag. Some like the MCTQ’s simplicity and some view it critically; it is time to have a self-critical view on the MCTQ, to address some misunderstandings and give some definitions about MCTQ-derived chronotype and the concept of social jetlag.

Backward electromagnetic waves are extraordinary waves with contra-directed phase velocity and energy flux. Unusual properties of the coherent nonlinear optical coupling of the phase-matched ordinary and backward electromagnetic waves with contra-directed energy fluxes are described which enable greatly-enhanced frequency and propagation direction conversion, parametrical amplification, as well as control of shape of the light pulses. Extraordinary transient processes that emerge in such metamaterials in pulsed regimes are described. The results of the numerical simulation of particular plasmonic metamaterials with hyperbolic dispersion are presented, which prove the possibility to match phases of such coupled guided ordinary and backward electromagnetic waves. Particular properties of the outlined processes in the proposed metamaterial are demonstrated through numerical simulations. Potential applications include ultra-miniature amplifiers, frequency changing reflectors, modulators, pulse shapers, and remotely actuated sensors.

Various tissue resident stem cells are receiving attention from basic scientists and clinicians as they hold certain promise for regenerative medicine. This paper is intended to clarify and facilitate the understanding, development and adoption of regenerative medicine in general and specifically of therapies based on unmodified, autologous adipose-derived regenerative cells (UA-ADRCs). To this end, results of landmark experiments on stem cells and stem cell therapy performed in the labs of the authors are summarized, the most intriguing of which are the following: (i) vascular associated mesenchymal stem cells (MSCs) can be isolated from different organs (adipose tissue, heart, skin, bone marrow and skeletal muscle) and differentiated into ectoderm, mesoderm and endoderm, providing significant support for the hypothesis of the existence of a small, ubiquitously distributed, universal vascular associated stem cell with full pluripotency; (ii) the orientation and differentiation of MSCs are driven by signals of the respective microenvironment; and (iii) these stem cells irrespective of the tissue origin exhibit full pluripotent differentiation potential without any prior genetic modification or the need for culturing. They can be obtained from a small amount of adipose tissue when using the appropriate technology for isolating the cells, and can be harvested from and re-applied to the same patient at the point of care without the need for complicated processing, manipulation, culturing, expensive equipment, or repeat interventions. These findings demonstrate the potential of UA-ADRCs for triggering the development of an entire new generation of medicine for the benefit of patients and of healthcare systems.

This study measures the noise levels in a baseball stadium and analyzes baseball fans’ attitude of effect of recreational noise exposure on their hearing. In the baseball stadium, noise levels were measured in four seating sections using a sound level meter during the games. The LAeq average of the 16 measures produced 91.7 dBA, showing a significantly high noise level in the red and navy sections. As a function of frequency by LZeq analysis, the noise levels were significantly higher in low frequencies than other frequencies. For the survey sample, 688 randomly selected participants completed a 16-question survey on their noise exposure during the game and on the potential risk of hearing loss. Despite the very high noise levels, 70% of the respondents preferred sitting in either the red or the navy section to be closer to the cheerleaders and to obtain a good view. Most respondents reported that they did not consider wearing earplugs, and one-third experienced hearing muffled speech after the game. We conclude that the noise levels in baseball stadiums are high enough to cause hearing damage and/or tinnitus later, but expect these results to improve public education regarding safe noise exposure during popular sports activities.

We have developed an unsteady and non-linear wind synopsis simulator called RIAM-COMPACT (Research Institute for Applied Mechanics, Kyushu University, COMputational Prediction of Airflow over Complex Terrain) in order to simulate the airflow on a microscale, i.e., a few tens of km or less. In RIAM-COMPACT, the large-eddy simulation (LES) has been adopted for turbulence modeling. LES is a technique in which the structures of relatively large eddies are directly simulated and smaller eddies are modeled using a sub-grid scale model. In the present study, we have conducted the numerical wind diagnoses for Taikoyama Wind Farm nacelle separation accident in Japan. The simulation results suggest that all six wind turbines at the Taikoyama Wind Farm are subject to significant influence from separated flow (terrain-induced turbulence) which is generated due to the topographic irregularities in the vicinity of the wind turbines. A proposal has been also made on reconstruction of the wind farm.

Photosynthetic activities of the sago palm (Metroxylon sagu Rottb.) were studied to find out its sensitivity to changes in ambient air temperature. The minimum ambient air temperature designed for the experiment was 25–29⁰C, while the higher end was 29–33⁰C. Several photosynthetic parameters were studied to support our analysis in sago photosynthetic activity, including diurnal leaf gas exchange, assimilation rate vs. CO₂ concentration, leaf greenness, leaf chlorophyll content, and photosynthetic rate vs. irradiance. We found that sago palm photosynthetic activity tends to be more sensitive to minimum than to maximum ambient air temperature. The plants exposed to higher air temperatures had dark green leaf color associated with higher rates of diurnal photosynthesis, chlorophyll content, and rubisco limited photosynthetic activity. They also exhibited higher trend in optimum irradiance absorption level. Consequently, maximum light energy dissipation occurred at higher temperatures.

The excitation of the visual system increases with increasing retinal illumination. At the same time, the sensitivity of the system decreases (light adaptation). Higher excitation automatically results in a lower sensitivity. This study investigates whether this parallelism between the excitation and the sensitivity also applies in the dynamic case, that is, during the transition to a higher excitation level after an increase in the retinal illuminance. For this purpose, the courses of the subjective and the electroretinographic threshold during the transitional phase after a step of the adaptation illumination was determined by means of a special light-stimulation apparatus. As a measure of the course of the excitation during this time, the response ERG on the adaptation step was recorded with a special amplifier. The threshold curve always has an overswing, which shows subjectively very strong differences. It can be concluded that the glare caused by a sudden increase in illuminance is subjectively very different. The comparison between the response ERG on the adaptation step and the course of the electroretinographic increment threshold during this time shows a broad agreement between the two courses. It can thus be assumed that the sensitivity of the visual system follows the course of the excitation also in the dynamic case. In addition, the investigation shows that the glare experienced after a step in the illuminance clearly shows great subjective differences.

Electrically conductive polymer composites are in high demand for modern technologies, however, the intrinsic brittleness of conducting conjugated polymers and the moderate electrical conductivity of engineering polymer/carbon composites have highly constrained their applications. In this work, super high electrical conductive polymer composites were produced by a novel hot embossing design. The polydimethylsiloxane (PDMS) composites containing short carbon fiber (SCF) exhibited an electrical percolation threshold at 0.45 wt%, and reached a saturated electrical conductivity of 49 S/m at 8 wt% of SCF. When reduced the sample thickness from 1.0 mm to 0.1 mm by the hot embossing process, a compression-induced percolation threshold occurred at 0.3 wt%, while the electrical conductivity was further enhanced to 378 S/m at 8 wt% SCF. Furthermore, the additional of a second nanofiller of 1 wt%, such as carbon nanotube or conducting carbon black further increased the electrical conductivity of the PDMS/SCF (8 wt%) composites to 909 S/m and 657 S/m, respectively. The synergy of the densified conducting filler network by the mechanical compression and the hierarchical micro-/nanoscale filler approach has realize super high electrical conductive yet mechanical flexible polymer composites for modern flexible electronics applications.

Background and objectives: Contrast-induced nephropathy (CIN), is an acute renal damage due to contrast agents. This study is conducted to determine the potential diagnostic value of hypoxia-inducible factor 2-alpha (HIF2-α) and to evaluate the renal protective effects of N-acetyl cysteine (NAC) and sildenafil in a rat CIN model. Material/Methods: This randomized, controlled, interventional animal study was conducted on Wistar rats. Totally, rats (n = 36) were randomly assigned to four groups: control (n = 9), CIN group (n = 9), CIN+NAC group (n = 9), and sildenafil (n = 9). The rat model was used to form iohexol-originated CIN. During the modelling, prophylactic treatment was performed at 24th and 48th hours. After 48 hours of the modelling; blood, urine, tissue samples were obtained for biochemical analyses. HIF-2-α levels were measured in renal tissue, serum and urine samples. Renal sections were performed in order for histopathologic and immunohistochemical evaluations. Results: In the CIN model, HIF-2α levels and other biochemical parameters were significantly increased (p < 0.01). Both sildenafil and NAC, efficiently decreased the renal damage due to contrast agents (p < 0.05). Similarly, after treatment with sildenafil and NAC, HIF-2α levels were significantly decreased (p < 0.05). Conclusions: The current study constructs an experimental base for the use of HIF-2α for clinical prevention and treatment of CIN. Several mechanisms may be postulated for the changes in HIF-2α levels. Besides, the increased HIF-2α levels with CIN and decreased HIF-2α levels after treatment may be used for the treatment and follow-up of patients with CIN.

This paper provides an overview of the new CPAM Project on Additive Manufacturing (AM) in design and simulation, focusing on topology & lattice structure optimization for a light-weighting advantage. This industry/academia collaboration project aims to utilize existing hardware and software tools, and investigate the practical limits of the technologies, providing eventual guidelines for general use. This will provide a solid foundation for the practical use of metal AM optimized solid and latticed structures especially for Ti6Al4V parts. Two case studies are demonstrated here, one a purely topology optimized design, and one also incorporating lattice optimized design, both from Ti6Al4V and load-bearing components, to be utilized in the Nelson Mandela University (NMU) Eco-Car Project in competition, late in 2018. This paper presents the Design for Additive Manufacturing (DfAM) process, the challenges met iro applying a DfAM design mindset, and a unique final voxel-based smoothing step finishing off the design process. Detailed structural integrity assessment of these parts are included - the question remains: can Additive Manufacturing help win the race?

Silicon light funnels are three-dimensional subwavelength structures in the shape of inverted cones with respect to the incoming illumination. Light funnel arrays can serve as an efficient absorbing layers on account of their light trapping capabilities associated with the presence of high density complex Mie modes. Specifically, light funnel arrays exhibit broadband absorption enhancement of the of the solar spectrum. In the current study, we numerically explore the optical coupling between surface light funnel arrays and underlying substrates. We show that the absorption in LF array-substrate complex is higher than the absorption in LF arrays of the same height (~10% increase). This, we suggest, imply that a LF array serves as an efficient surface element that imparts additional momentum components to the impinging illumination, and hence optically excites the substrate by near-field light concentration, excitation of traveling guided modes in the substrate and mode hybridization.

Static (SLS) and dynamic (DLS) light scattering techniques are assessed for their capacity to detect colloidal particles with diameters between d = 0.1 and 0.8 µm at very low concentrations in seawater. The detection limit of the apparatus was determined using model monodisperse spherical polystyrene latex particles with diameters 0.2 µm and 0.5 µm. It is shown that the concentration and size of colloids can be determined down to about 10^-6 g/L. Seawater obtained from different locations in western Europe was characterized using light scattering. It was found that seawater filtered through 0.45 µm pore size membrane filters was within the experimental error the same as that of ultrapure Milli-Q water containing the same amount of sea salt and no colloids could be detected with DLS. When the seawater was filtered through 0.8 µm pore size filters, colloidal particles were detected. The measurements show that the concentration of colloids in the seawater samples is not higher than 10^-6 g/L and that they have an average diameter of about 0.6 µm. We stress that these particles are not necessarily nanoplastics.

The development of 3D cerebral brain organoids which accurately resemble aspects of the human brain permits a more accurate characterization of physiological processes and neurological diseases. Cerebral organoids can be grown from stem cell lines with various genetic backgrounds allowing multiple neurodegenerative diseases to be modeled. While dysfunction in neurotransmission of patients with neurodegenerative diseases is expected, the impact of chronic neurodegeneration on the response to viral infection of the CNS is poorly understood. For instance, several mosquito-borne viruses like Dengue virus and West Nile Virus cause post-viral parkinsonism. How CNS infection might impact a host with inherent CNS dysfunction such as Parkinson’s Disease in poorly understood. This preliminary, observational study aimed to understand dysfunction in intrinsic and innate expression of a patient with a neurodegenerative disease and a non-affected individual in relation to potential viral infection in the CNS. Cerebral organoids were generated from human induced pluripotent stem cells with a normal genetic background or with idiopathic Parkinson’s Disease. After differentiation and maturation, organoid size, gene expression and immunofluorescence were evaluated to assess neurotransmission and innate immunity. While there was no significant difference in size of the organoids with a normal or Parkinson’s genetic background, gene expression studies identified multiple differences in innate immunity and neurotransmission. Immunofluorescence also identified differences in protein expression related to neurotransmission and innate immunity. Of note, organoids derived from a Parkinson’s patient exhibited endogenous up-regulation of dopamine and muscarinic acetylcholine receptors, GABA, glycine, and glutamate targets, and the majority of cytokines. This expression pattern suggests a chronic state of neuroexcitation and neuroinflammation in this population of organoids.

We report on the study of energy-harvesting performance in medium-size (400 cm²) glass-based semitransparent solar concentrators employing edge-mounted photovoltaic modules. Systems using several different types of glazing system architecture and containing embedded diffractive structures are prepared and characterized. The technological approaches to the rapid manufacture of large-area diffractive elements suitable for use in solar window-type concentrators are described. These elements enable the internal deflection and partial trapping of light inside glass-based concentrator windows. We focus on uncovering the potential of pattern-transfer polymer-based soft lithography for enabling both the improved photon collection probability at solar cell surfaces, and the up-scaling of semitransparent solar window dimensions. Results of photovoltaic characterization of several solar concentrators employing different internal glazing-system structure and diffractive elements produced using different technologies are reported and discussed.

Fibrillin (FBN) is a plastid lipid-associated protein found in photosynthetic organisms from cyanobacteria to plants. In this study, 10 CsaFBN genes were identified in genomic DNA sequences of cucumber (Chinese long and Gy14) through database searches using the conserved domain of FBN and the 14 FBN genes of Arabidopsis. Phylogenetic analysis of CsaFBN protein sequences showed that there was no counterpart of Arabidopsis and rice FBN5 in the cucumber genome. FBN5 is essential for growth in Arabidopsis and rice; its absence in cucumber may be because of incomplete genome sequences or that another FBN carries out its functions. Among the 10 CsaFBN genes, CsaFBN1 and CsaFBN9 were the most divergent in terms of nucleotide sequences. Most of the CsaFBN genes were expressed in the leaf, stem, and fruit. CsaFBN4 showed the highest mRNA expression levels in various tissues, followed by CsaFBN6, CsaFBN1, and CsaFBN9. High-light stress combined with low temperature decreased photosynthetic efficiency and highly induced transcript levels of CsaFBN1, CsaFBN6, and CsaFBN11, which decreased after 24 h treatment. Transcript levels of the other seven genes were changed only slightly. This result suggests that CsaFBN1, CsaFBN6, and CsaFBN11 may be involved in photoprotection under high-light conditions at low temperature.

The ANFC/ABPE-10 composite film was prepared by ABPE-10 impregnating into ANFC films under negative pressure. And the composite film had meted high performance FOLED substrate requirement even when ANFC dosage was high for approximately 70%, which was consistent with for low cost efficiency, recyclability, and environmentally friendly. The enhanced properties of ANFC films were mainly because of the nature of ABPE-10 itself and the IPN structure formed between ABPE-10 and ANFC film. The transparency of composite films with different ANFC dosage was significantly increased from 67% to 88% by UV-Vis analysis. The composite film inherited the properties of AFNC, obtaining low CTE characteristics and ductile compact structure. The contact angles of ANFC films increased by 102% from 49.2° to 102.9°after dipping ABPE-10. Additionally, the composite films had outstanding mechanical properties such as tensile strength 173.72 MPa, Young’s modulus 4.06 GPa, and elongation at break 5.81%.

Duchenne muscular dystrophy (DMD) is a fatal X-linked recessive neuromuscular disease prevalent in 1 in 3500 to 5000 males worldwide. As a result of mutations that interrupt the reading frame of the dystrophin gene (DMD), DMD is characterized by a loss of dystrophin protein which leads to decreased muscle membrane integrity, which increases susceptibility to degeneration. CRISPR/Cas9 technology has garnered interest as an avenue for DMD therapy due to its potential for permanent exon skipping, which can restore the disrupted DMD reading frame in DMD and lead to dystrophin restoration. An RNA-guided DNA endonuclease system, CRISPR/Cas9 allows for the targeted editing of specific sequences in the genome. The efficacy and safety of CRISPR/Cas9 as a therapy for DMD has been evaluated by numerous studies in vitro and in vivo, with varying rates of success. Despite the potential of CRISPR/Cas9-mediated gene editing for the long-term treatment of DMD, its translation into the clinic is currently challenged by issues such as off-targeting, immune response activation, and sub-optimal in vivo delivery. Its nature as being mostly a personalized form of therapy also limits applicability to DMD patients, who exhibit a wide spectrum of mutations. This review summarizes the various CRISPR/Cas9 strategies that have been tested in vitro and in vivo for the treatment of DMD. Perspectives on the approach will be provided, and the challenges faced by CRISPR/Cas9 in its road to the clinic will be briefly discussed.

Nanoparticles -- regularly patterned or randomly dispersed -- are a key ingredient for emerging technologies in photonics. Of particular interest are scattering and field enhancement effects of metal nanoparticles for energy harvesting and converting systems. An often neglected aspect in the modeling of nanoparticles are light interaction effects beyond classical electrodynamics stemming from electron dynamics in confined and accelerated systems. We give a detailed account on free electron phenomena in metal nanoparticles and discuss analytic expressions, stemming from microscopic and semi-classical theories. These can improve standard computational schemes to produce more reliable results on the optical properties of metal nanoparticles. We combine these solutions into a single framework and study their joint impact on isolated Au, Ag, and Al nanoparticles as well as dimer structures.

This work examines atomic and molecular signatures in laser-induced plasma in standard ambient temperature and pressure environments, including background contributions to the spectra that depend on the laser pulse-width. Investigations include solids, gases, and nano-particles. Abel inversions of measured line-of-sight data reveal insight into the radial plasma distribution. For nominal 6 nanosecond laser pulses and for pulse-energies in the range of 100 to 800 milli-Joules, expansion dynamics and turbulence due to shock phenomena are elucidated to address local equilibrium details that are frequently assumed in spatially averaged emission spectroscopy. Chemical equilibrium computations reveal temperature dependence of selected plasma species. Specific interests include atomic hydrogen (H) and cyanide (CN). The atomic H spectra, collected following optical breakdown in ultra-high-pure hydrogen and 9:1 mixtures of ultra-pure hydrogen and nitrogen gases, indicate spherical shell structures and isentropic expansion of the plasma kernel over and above the usual shockwave. The recombination radiation of CN emanates within the first 100 nanoseconds for laser-induced breakdown in a 1:1 CO₂:N₂ gas mixture when using nanosecond laser pulses to create the micro-plasma. The micro-plasma is generated using 1064 nm, 150 mJ, 6 ns Q-switched Nd:YAG laser radiation. Measurements of the optical emission spectra utilize a 0.64 m Czerny-Turner type spectrometer and an intensified charge-coupled device.

In this work, the parameters of plasma (electron temperature (T_e), electron density n_e, plasma frequency (f_p) , Debye length (λ_D) and Debye number (N_D)) have been studied by using the spectrometer that collect the spectrum of Laser produce Cadmium telluride plasma at different energies. The results of electron temperature for CdTe range 0.93-1.18 eV also the electron density 5 × 10¹⁰ – 3.8 × 10¹¹ cm^-3 have been measured under vacuum reaching 2.5 × 10^-2 mbar .Optical properties of CdTe were determined through the optical transmission method using ultraviolet visible spectrophotometer within the range 190 – 1100 nm.

This work communicates a review on Balmer series hydrogen beta line measurements and applications for analysis of white dwarf stars. Laser-induced plasma investigations explore electron density and temperature ranges comparable to white dwarf star signatures such as Sirius B, the companion to the brightest star observable from the earth. Spectral line shape characteristics of the hydrogen beta line include width, peak separation, and central dip-shift, thereby providing three indicators for electron density measurements. The hydrogen alpha line shows two primary line-profile parameters for electron density determination, namely, width and shift. Both Boltzmann plot and line-to-continuum ratios yield temperature. The line-shifts recorded with temporally- and spatially- resolved optical emission spectroscopy of hydrogen plasma in laboratory settings can be larger than gravitational redshifts that occur in absorption spectra from radiating white dwarfs. Published astrophysical spectra display significantly diminished Stark or pressure broadening contributions to red-shifted atomic lines. Gravitational redshifts allow one to assess the ratio of mass and radius of these stars, and subsequently, the mass from cooling models.

The human degenerative cartilage has low regenerative potential. Chondrocyte transplantation offers a promising strategy for cartilage treatment and regeneration. Currently chondrogenesis using human pluripotent stem cells are accomplished using human recombinant growth factors. Here, we differentiated human induced pluripotent stem cells (hiPSCs) into chondrocytes and cartilage pellet using minicircle vectors. Minicircles are used as a non-viral gene delivery system for gene therapy in various diseases. Non-viral gene delivery can produce growth factors without integrating into the host genome. Minicircle vectors containing bone morphogenetic protein 2 (BMP2) and transforming growth factor, beta 3 (TGFβ3) were successfully generated and delivered to hiPSC-derived outgrowth (OG) cells. Cell pellets generated using minicircle-transfected OG cells successfully differentiated into chondrogenic lineage. Chondrogenic pellets transfected with growth factor-encoding minicircles effectively recovered osteochondral defect in rat models. Taken together, this work shows the potential application of minicircles in cartilage regeneration using hiPSCs.

Type 1 diabetes affects millions of people globally and requires careful management to avoid serious long-term complications, including heart and kidney disease, stroke, and loss of sight. The present standard-of-care for type 1 diabetes is exogenic insulin substitutional therapy. The most advanced stretegies in this area is the development of hybrid-closed loop system and the producing of long-acting insulins. Progresses in stem cell therapies have started to revolutionize the care of patients with type 1 diabetes; however, significant challenges remain including the limited islets availability, difficulties in maintaining the viability, the heterogeneity within a complex pathology and in patients’ responses to treatment. On the way, a considerable amount of efforts in maximizing the islet transplantation effectiveness by controlling the advantageous of different stem cell approaches. With the availability and the use of big data, the concept of precision medicine is gaining wide attention worldwide and could bring the dream of “presonlaized” therapies as a reality in the near future. Here we review the current range of treatments available as well as recent pre-clinical breakthroughs in the field of personlaized medicine for type 1 diabetes.

Pre-existing fracture and secondary cracks in rock mass are formed by natural power, such as magma condensed to igneous rocks and tectonic movement. The orientation and inclination of these fractures obey certain laws relating to the stress, temperature, minerals, water and so on. Therefore, cracks react differently under the same external loading on the condition of various inclination, fissure apertures, stiffness and joint roughness. To simulate the crack propagation, experiments on hollow cylinder cut by one oblique interface mimicking single fracture accumulated numerous data discovering the failure criterion in accordance with the Mohr-Coulomb criterion. And theory on the Terzaghi’s effective principle take an essential role in controlling the behavior of triggering fault. This paper introduced a series of oblique plane cutting the cylinder regarded as fractures at different inclination to concentrate on how the fracture characteristics effect the stress and strain distribution inside the specimen, especially, the relationship between displacement and water head. The key point of this numerical simulation is coupling the solid phase and the fluid phase, specifically, the mechanic and seepage field. According to the statics, curves referring to deformation and water head could be described as increasing lines. Besides, simulation on coupling solid phase and fluid phase can supply crucial evaluation on activating existing fault, and thus predicting induced seismicity in reservoirs or estimating damage in shale gas exploration.

Wildlands are increasingly lost to human development. Conservation scientists repeatedly call for protecting the remaining wildlands and expanding the land area protected in reserves. Despite these calls, conservation reserves can be eliminated through legislation that demotes their conservation status. For example, legislation introduced to the Congress of the United States recently would demote 29 Wilderness Study Areas (WSAs) from the protections afforded by their existing status. The legislation suggests that the 29 areas are not suitable for a promotion and future inclusion in the National Wilderness Preservation System based on decades-old local evaluations. Local evaluations, notwithstanding, it may be important to consider the value of lands from a national perspective. Without a national perspective, local evaluations alone may overlook the national significance of lands. With this in mind, I used five qualities of wildland value (wildness, light pollution, noise pollution, intactness of mammals, and intactness mammal carnivores of conservation concern) to compare the 29 WSAs to all national parks and wilderness areas located within the contiguous United States. The pool of 29 WSAs were similar to the pool of national parks and wilderness with respect to the five qualities assessed, and some of the WSAs were characterized by higher values than most of national parks and wilderness areas. This analysis demonstrates the national significance of the WSAs targeted for conservation status demotion. Such an approach could be used in future land management legislation and planning to ensure that a national perspective on conservation value is brought to bear on decisions facing federally-managed lands.

Physics behind collimated highly directional nature of lasers, and factors that keep the seven coloured waves that form white light together during their journey from Sun to Earth, in the face of the natural disruptive forces, is not fully understood. Energy levels were measured, in terms of alterations in induced current and voltage, in beams from a red laser, white LED light and the Sunlight before and during their disruption by diffusers (frosted glass for the lasers) and diffractors (diffraction grating for the white light) using a photovoltaic solar cell panel attached to a digital multimeter. Results show that disruption of the beams results in release of extra energy named as ‘Latent Light Binding’ Energy’. It is hypothesized that the ‘binding’ energy keeps laser waves firmly bound together both end-on and side-on enabling laser beams to travel long distances in collimated manner. Likewise, the 7 coloured waves that constitute white light are kept together, probably side-on, in their journey from the Sun to the Earth. The observation that diffraction of sunbeam is associated with increased power generation provides a new lead to improve harnessing of solar energy, where, currently, the focus is mainly on improving efficiency of photovoltaic cell.

The growing awareness of the biological effects of artificial light on humans has stimulated ample research. It is now widely accepted that asynchrony between artificialand natural light-dark cycles can elicit severe detrimental health effects. New research has been devoted to lighting solutions that dynamically change their color to mimic spectral changes of daylight and to account for human needs. However, in some situations, the visual properties of light must be preserved: For example professional TV video editors and shift workers who must work under standardized lighting conditions to do color correction in post-production. We have investigated the possibility to tune circadian effects using white lights that are spectrally different but nonetheless have similar color coordinates thus appear as a similar white tone. Our simulation results indicate that it is possible to modulate circadian light effects by combining LEDs for neutral white (4000 K), a widely used white tone for indoor lighting in europe. The results also show that the solutions combining single-color LEDs do however not meet the quality criteria from the visual point of view because their color rendering ability decays to unacceptable low levels. Combining narrowband LEDs with a broadband white LED improves the color rendering quality and we show how far circadian light effects can be tuned according to common theoretical models. The aim is to reflect daylight situations with artificial lighting, thus having a high melatonin suppression in the morning and low melatonin suppression in the evening. As a consequence our aim is to show what maximum and minimum circadian effect is possible with the same set of LEDs.

The color changes corresponding to chromophore structures in lignin caused by exposure of Eucalyptus（Eucalyptus grandis and E. urophylla）to heat were investigated. Eucalyptus wood samples were heated in saturated steam atmospheres for 10 h at 110℃, 130℃, and 150℃. The lignin was isolated before and after heat treatment. The physicochemical properties of the lignin and changes in chromophore structures during heat treatment was evaluated through wet chemical analysis, FTIR, UV-Vis, GPC, XPSand 13C-NMR. The color of the wood became darker and redder with the increase in pressure and temperature. Depolymerization and dehydration reactions occurred via demethoxylation with heat treatment in saturated steam at 110℃ or 130℃. Lignin condensed to form insoluble compounds after heat treatment in saturated steam at 150℃. G units increased and S units decreased through demethylation during heat treatment, as revealed by FTIR and 13C-NMR analysis.

Background: Alzheimer’s disease (AD), the most threatening neurodegenerative diseases, is characterized by the loss of memory and language function, an unbalanced perception of space and other cognitive and physical manifestations. Pathology of the AD is characterized by neuronal loss, and the extensive distribution of senile plaques and neurofibrillary tangles (NFTs). The role of environment and the diet in the AD is being studied actively, and nutrition is certainly one of the main factors playing a prominent role in the prevention of neurodegenerative diseases. In this context, the relationship between dementia and wine use/abuse has received increased research interest in recent times, with varying and often conflicting results. Scope and approach: This review aims to critically summarize the most recent studies conducted to clarify the relationship between wine drinking and AD, as well as whether effects are influenced by quantity and/or frequency of drinking. Key findings and Conclusion: Overall, based on the interpretation of various studies, it can be concluded that there is no indication that light to moderate alcohol drinking is detrimental to cognition and dementia, and it is not possible to define whether alcohol could be used as a means to reduce risk of developing AD.

Direct reprogramming of fibroblasts into induced cardiomyocytes (iCMs) holds a great promise for regenerative medicine and has been studied in several major directions. However, cell-cycle regulation, a fundamental biological process, has not been investigated during iCM-reprogramming. Here, our time-lapse imaging on iCMs, reprogrammed by Gata4, Mef2c, and Tbx5 (GMT) monocistronic retroviruses, revealed that iCM-reprogramming was majorly initiated at late-G1- or S-phase and nearly half of GMT-reprogrammed iCMs divided soon after reprogramming. iCMs exited cell cycle along the process of reprogramming with decreased percentage of EdU⁺/αMHC-GFP⁺ cells. S-phase synchronization post-GMT-infection could enhance cell-cycle exit of reprogrammed iCMs and yield more GFP^high iCMs, which achieved an advanced reprogramming with more expression of cardiac genes than GFP^low cells; however, S-phase synchronization didn’t enhance the polycistronic-MGT reprogramming, in which cell-cycle exit had been accelerated. In conclusion, post-infection synchronization of S-phase facilitated the early progression of GMT-reprogramming through a mechanism of enhanced cell-cycle exit.

The resonance spectra of neutral silver indicate self-absorption for the studied Ag I lines at the wavelengths of 327.9 nm and 338.2 nm. The center dip is associated with self-reversal due to self-absorption in the plasma. The Q-switched radiation of 355 nm, 532 nm, or 1064 nm from a Nd:YAG laser device generates the plasma at the surface of silver nano-material targets, with experiments conducted in standard ambient temperature and pressure laboratory air. Procedures for recovery of the spectral line shapes confirm that over and above the effects of self-reversal, line shape distortion are important in the analysis. The work discusses parameters describing self-absorption when using fluence levels of 2 to 33 J/cm² to generate the plasma. Furthermore, subsidiary calibration efforts that utilize the hydrogen alpha line of the Balmer series show that the Ag I lines at 827.35 nm and 768.7 nm are optically thin.

Globally 30% of landslides occur in the northeastern part of India [1]. One of the major earthquake events in Sikkim, India occurred on 18th September 2011 (Mw 6.9) led to over 300 landslides and 122 human deaths [2]. These landslides not only controlled by natural disasters but initiated due to human activities. The present study considered Lungchok landslide occurred in south district of Sikkim due to 2011 seismic event. The study focused on the failure mechanism of the landslide based on finite element analysis by adopting eight different cases. The deformation characteristic was investigated for dry and saturated slope conditions under static and dynamic behavior considering vehicle loads using GeoStudio software. The FEM analysis has been carried out using load deformation and linear elastic. The analysis shows that the failure of the slope was not sudden due to the 2011 earthquake event, but progressive failure was observed with time and construction activity. The paper demonstrates that, an increase in infrastructure development including construction by hill cutting increased the initiation of landslide with soil erosion. The cracks developed after 2011 earthquake event led to further deformations during future disasters required effective stabilization measures.

Amorphous silicon (α-Si) film present an inexpensive and promising material for optoelectronic and nanophotonic applications. Its basic optical and optoelectronic properties are known to be improved via phase transition from amorphous to polycrystalline phase. Infrared femtosecond laser radiation can be considered as a promising nondestructive and facile way to drive uniform in-depth and lateral crystallization of α-Si films that are typically opaque in UV-visible spectral range. However, so far only a few studies reported on utilization of near-IR radiation for laser-induced crystallization of α-Si providing no information regarding optical properties of the resultant polycrystalline Si films. The present work demonstrates efficient and gentle single-pass crystallization of α-Si films induced by their direct irradiation with near-IR femtosecond laser pulses coming at sub-MHz repetition rate. Comprehensive analysis of morphology and composition of laser-annealed films by atomic-force microscopy, optical, micro-Raman and energy-dispersive X-ray spectroscopy, as well as numerical modeling of optical spectra, confirmed efficient crystallization of α-Si and high-quality of the obtained films. Moreover, we highlight localized laser-driven crystallization of α-Si as a promising way for optical information encryption, anti-counterfeiting and fabrication of micro-optical elements.

A fast calculation method for the full parallax high-resolution hologram is proposed based on the elemental light field image (EI) rendering. A 3D object located near the holographic plane is firstly rendered as multiple EIs with a pinhole array. Each EI is interpolated and multiplied by a divergent sphere wave and interfered with a reference wave to form a hogel. Parallel acceleration is used to calculate the high-resolution hologram because calculation of each hogel is independent. A high-resolution hologram with the resolution of 20,0000×20,0000 pixels is calculated only within 8 minutes. Full parallax high-resolution 3D displays are realized by optical reconstructions.

In the literature of Low-Energy Nuclear Reactions (LENR), particle tracks in photographic emulsions (and other materials) associated with certain electrical discharges have been reported. Some Russian and French researchers have considered these particles to be magnetic monopoles. These tracks correspond directly to tracks created with a simple uniform exposure to photons without an electrical discharge source. This simpler method of producing tracks supports a comprehensive exploration of particle track properties. Out of 750 exposures with this method, elliptical particle tracks were detected, 22 of which were compared to Bohr-Sommerfeld electron orbits. Ellipses fitted to the tracks were found to have quantized semi-major axis sizes with ratios of ≈n²/α² to corresponding Bohr-Sommerfeld hydrogen ellipses. This prompts inquiry relevant to magnetic monopoles due to the n²/α² force difference between magnetic charge and electric charge using the Schwinger quantization condition. A model using analogy with the electron indicates that the elliptical tracks could be created by a bound magnetically charged particle with mass m_m = 1.45 × 10^-3 eV/c², yet with superluminal velocities. Using a modified extended relativity model, m_m becomes the relativistic mass of a superluminal electron, with m₀ = 5.11 × 10^-3 eV/c², the fine structure constant becomes a mass ratio and charge quantization is the result of two states of the electron.

The study of neurodegenerative diseases using pluripotent stem cells requires new methods to assess neurodevelopment and neurodegeneration of specific neuronal subtypes. The cholinergic system, characterized by its use of the neurotransmitter acetylcholine, is one of the first to degenerate in Alzheimer’s disease and is also affected in frontotemporal dementia. We developed a differentiation protocol to generate basal forebrain cholinergic neurons (BFCNs) from induced pluripotent stem cells (iPSCs) aided by the use of small molecule inhibitors and growth factors. Ten iPSC lines were successfully differentiated into BFCNs using this protocol. The neuronal cultures were characterised through RNA and protein expression, and functional analysis of neurons was confirmed by whole-cell patch clamp. We have developed a reliable protocol using only small molecule inhibitors and growth factors, while avoiding transfection or cell sorting methods, to achieve a BFCN culture that expresses the characteristic markers of cholinergic neurons.

With the growing size and use of night lights time series from the Visible Infrared Imaging Radiometer Suite Day/Night Band (DNB), it is important to understand the stability of the dataset. All satellites observe differences in pixel values during repeat observations. In the case of night lights data, these changes can be due to both environmental effects and changes in light emission. Here we examine the stability of individual locations of particular large scale light sources (e.g. airports, prisons) in the monthly composites of DNB data from April 2012 to September 2017. The radiances for individual pixels of most large light emitters are approximately normally distributed, with a standard deviation of typically 15-20% of the mean. We observe geospatial autocorrelation in the monthly variations for nearby sites, while the correlation for sites separated by large distances is small. This suggests that local factors contribute most to the variation in the pixel radiances, and furthermore that averaging radiances over large areas will reduce the total variation. A better understanding of the causes of temporal variation would improve the sensitivity of DNB to lighting changes.

Silybum marianum L. is a well-known medicinal herb, primarily used in liver protection. Light strongly affects several physiological processes along with secondary metabolites biosynthesis in plants. Herein, S. marianum was exploited for in vitro potential under different light regimes in the presence of melatonin. The optimum callogenic response occurred in combination of 1.0 mg/L α-naphthalene acetic acid and 0.5 mg/L 6-Benzylaminopurine under photoperiod. Continuous light associated with melatonin treatment increased total flavonoid content (TFC), total phenolic content (TPC) and antioxidant potential, followed by photoperiod and dark treatments. The increased level of melatonin has a synergistic effect on biomass accumulation under continuous light and photoperiod, while adverse effect was observed under dark condition. More detailed phytochemical analysis showed maximum total silymarin content (11.92 mg/g DW) when placed under continuous light + 1.0 mg/L melatonin. Individually, the level of silybins (A and B), silydianin, isolsilychristin and silychristin was found highest under continuous light. Anti-inflammatory activities were also studied and highest percent inhibition was recorded against 15-LOX for cultures cultivated under continuous light (42.33%). The current study helps to better understand the influence of melatonin and different light regimes on silymarin production as well as antioxidant and anti-inflammatory activities in S. marianum callus extracts.

Ongoing investigations have highlighted that MIM of Mg shows high potential for mass production of small lightweight components as well as of degradable implants with complex geometry. However, prior research activities have shown that Mg reacts sensitively to atmosphere impurities like oxygen and specific thermal decomposition products of the used backbone polymers. Polyethylene based polymers reveal a negative influence on sintering of Mg while polypropylene based polymers behave uncritically. This work is highlighting that when hydrogen instead of argon atmosphere is used during sintering, the negative influence caused by carbon residuals at the particle boundaries can be prevented. Mg-0.9Ca elongation increased with a slight decrease in UTS revealing a strengthening effect of the carbon residuals at the particle boundaries. For pure Mg UTS could be increased from 7 MPa up to 80 MPa with elongation of 6% showing the positive effect of hydrogen on the sintering of Mg.

Spherical microparticles of TiO₂ were synthesized by the ionic liquid-assisted solvothermal method at different reaction time (3, 6, 12 and 24h). The properties of the prepared photocatalysts were investigated by means of UV-vis diffuse-reflectance spectroscopy (DRS), BET surface area measurements, scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), and X-ray photoelectron spectroscopy (XPS). The results indicated that the efficiency of phenol degradation was related with a time of the solvothermal synthesis as determined for TiO₂_EAN(1:1)_24h sample. Microparticles of TiO₂_EAN(1:1)_3h formed during the only 3h of synthesis time revealed really high photoactivity under visible irradiation – 75%. This value increased to 80% and 82% after 12h and 24h, respectively. The photoactivity increase was accompanied by the increase of the specific surface area thus pores size, as well as ability to absorb UV-vis irradiation. The high efficiency of phenol degradation of IL-TiO₂ photocatalysts was ascribed to the interaction between the surface of TiO₂ and ionic liquid components (carbon and nitrogen).

The presence of azo dyes in textile effluents is an issue of major concern due to their potential impact on the environment and human health. In this study we investigate the photocatalytic degradation under visible light of Reactive Violet 5 (RV5), an azo dye widely used in the textile industry. A preliminary screening of different titania-based catalysts was carried out to identify the best candidate for RV5 removal. The selected catalyst was then tested in a stirred and aerated lab-scale reactor illuminated with a light LED source (λmax = 460 nm). The effects of pH, catalyst load and hydrogen peroxide additions on the efficiency of dye removal were evaluated. Under the best conditions (pH 10, 3 g/L of catalyst and 60 mM hydrogen peroxide), the dye solution was completely decolorized in about 2 h. Overall, the results obtained suggest that the proposed process may represent a suitable method for the removal of RV5 from textile effluents.

This work reports measurements of calcified gallstone elemental compositions using laser-induced optical emission spectroscopy. The experimental results support the importance of the magnesium concentration in gallstone growth. Granular stones reveal an increased magnesium concentration at the periphery of the granules, suggesting the inhibition of further growth. Non-granular gallstones reveal lower overall magnesium concentrations but with higher values near the center.

In table tennis competitions the rule violation judgment with the greatest controversy is the height of the ball serve. This is because inaccuracy in the ball height judgment, which results in erroneous judgment, is unavoidable. Thus, we designed an automatic image judgment auxiliary system for table tennis ball height during service in this study. We used a high-speed camera to record the ball toss in the table tennis service. The designed algorithm architecture can automatically search for the ball and the position of the hand action under low light source conditions. The algorithm is mainly divided into hue-saturation-value color space processing and morphology processing using Hough transform to search for the circular ball. Experiment result shows that color segmentation can successfully and accurately determine the ball position under low light conditions. The morphology method can find the position of the hand and help determine the moment when the ball leaves the hand during the service ball toss. Finally, the actual size of the target is used to estimate the actual distance unit represented by the image pixel.

Plants grown under fluctuating light impact plant developments compared with those grown under non-fluctuating light conditions. However, our knowledge on the underlying regulatory mechanisms is still quite limited, particularly from the transcriptional perspective. In order to investigate the influence of different light intensity distributions on tomato plant development, we designed three fluctuating light intensity distributions with the non-fluctuating light intensity as control and compared the transcriptional differences after five weeks of treatment. We found plant height and aerial/root weight were significantly reduced under all fluctuating light treatments. Transcriptome analysis revealed that the number of up and down regulated genes had a distinct distribution pattern between different treatments and control. The largest difference between the numbers of down and up regulated genes was found between treatment 1 and 3, reaching to a total of 416 genes. The number and type of the top 20 enriched pathways differed between treatments and control. The largest number of genes enriched was involved in the biosynthesis of secondary metabolites. These results provide insights into the transcriptional regulations of tomato under different light intensity distributions.