The application of 3D LiDAR technology has become increasingly extensive in tunnel monitoring due to the large density and high accuracy of the acquired spatial data. The proposed processing method aims at circle tunnels and provides a clear workflow to automatically process raw point data and easily interpretable results to analyze tunnel health state. The proposed automatic processing method employs a series of algorithms to extract point cloud of a single tunnel segment without obvious noise from entire raw tunnel point cloud mainly by three steps: axis acquisition, segments extraction and denoising. Tunnel axis is extracted by fitting boundaries of the tunnel point cloud rejection in plane with RANSAC algorithm. With guidance of axis, the entire preprocessed tunnel point cloud is segmented by equal division to get a section of tunnel point cloud which corresponds to a single tunnel segment. Then the noise in every single point cloud segment is removed by clustering algorithm twice, based on distance and intensity. Finally, clean point clouds of tunnel segments are processed by effective deformation extraction processor to get ovality and three-dimensional deformation nephogram.

Deep-ultraviolet (UV) light-emitting diodes (LEDs) based on AlGaN crystals have low light-emission efficiency; therefore, there is a need to improve this light-emission efficiency for a wide range of applications such as water and air sterilizations. UV-light-transparent device structures are considered one of the many solutions toward increasing light output power. To this end, the present study focused on developing a transparent AlGaN-based tunnel junction (TJ) as the anode of a deep-UV LED. Deep-UV LEDs composed of n+/p+-type AlGaN TJs were fabricated under the growth condition that reduced the carrier compensation in the n+-type AlGaN layers. The operating voltage was 10.8 V under the direct current (DC) operation of 63 A/cm2. In addition, magnesium zinc oxide (MgZnO)/Al reflective electrodes were fabricated to enhance the output power of the AlGaN homoepitaxial TJ LED. The output power was 57.3 mW under a DC operation of 63 A/cm2, and it was 1.7 times higher than that realized using the conventional Ti/Al electrodes. The combination of the AlGaN-based TJ and MgZnO/Al reflective contact allows further improvement of the light output power. This study confirms that the AlGaN TJ is a promising UV-transmittance structure that can obtain a high light-extraction efficiency.

Understanding user challenges with light dosimeters is crucial for designing more acceptable devices and advancing light exposure research. We systematically evaluated the usability and acceptability of the lido (light dosimeter) by 29 participants who wore the dosimeter near the corneal plane of the eye for 5 days. Common reasons for not wearing the dosimeter included exercise, recharging, wet environments, public settings, and discomfort. Despite these issues, participants adhered to using the dosimeter, with high compliance (89% of recording time). Our findings reveal a significant discrepancy between mean melanopic Equivalent Daylight Illuminance (300 lxmEDI) and median values (51 lxmEDI). This discrepancy indicates that, for most of the time, participants experienced significantly lower light levels. Specifically, participants were exposed to light levels above 250 lxmEDI for only 14% of their wearing time. This highlights the need for increased exposure to recommended light levels. In the evening, participants' light exposure was below the recommended 10 lxmEDI for 58% of the wear time, which is in line with the guidelines for reducing light exposure before sleep. This study highlights the critical need for strategies to enhance daily light exposure, aligning better with circadian health recommendations.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

Considering animal welfare, the free-range laying hen farming model is increasingly gaining attention. However, in some countries, large-scale farming still relies on the cage-rearing model, making the focus on the welfare of caged laying hens equally important. To evaluate the health status of caged laying hens, a dataset comprising visible light and thermal infrared images was established for analyses, including morphological, thermographic, comb, and behavioural as-sessments, enabling a comprehensive evaluation of the hens' health, behaviour, and population counts. To address the issue of insufficient data samples in the health detection process for indi-vidual and group hens, a dataset named BClayinghens was constructed containing 61,133 images of visible light and thermal infrared images. The BClayinghens dataset was completed using three types of devices: smartphones, visible light cameras, and infrared thermal cameras. All thermal infrared images correspond to visible light images and have achieved positional alignment through coordinate correction. Additionally, the visible light images were annotated with chicken head labels, obtaining 63,693 chicken head labels, which can be directly used for training deep learning models for chicken head object detection and combined with corresponding thermal infrared data to analyze the temperature of the chicken heads. To enable the constructed deep-learning object detection and recognition models to adapt to different breeding environ-ments, various data enhancement methods such as rotation, shearing, colour enhancement, and noise addition were used for image processing. The BClayinghens dataset is important for ap-plying visible light images and corresponding thermal infrared images in the health detection, behavioural analysis, and counting of caged laying hens under large-scale farming.

Background/Objectives: We defined the value of a machine learning algorithm to distinguish between the EEG response to no light or any light stimulation, and between red or green light stimulation in awake volunteers with closed eyelids. This new method of EEG analysis is visionary in the understanding of visual signal processing and will facilitate anaesthetic depth research. Methods: X-gradient boosting models were used to classify the cortical response to VEP stimulation (no light vs. any light stimulation; red vs. green light stimulation). For each of the two classifications, three scenarios were tested: training and prediction in all participants (all), training and prediction in one participant (individual), training across all but one participant with prediction in the participant left out (one out). Results: Ninety-four Caucasian adults were included. The machine learning algorithm had a very high predictive value and accuracy in differentiating between no light and any light stimulation (AUCROCall: 0.96; accuracyall: 0.94; AUCROCindividual: 0.96±0.05, accuracyindividual: 0.94±0.05; AUCROConeout: 0.98±0.04; accuracyo-neout:0.96±0.04). The machine learning algorithm was highly predictive and accurate in distinguishing between green and red colour stimulation (AUCROCall: 0.97; accuracyall: 0.91; AUCROCin-dividual: 0.98±0.04, accuracyindividual: 0.96±0.04; AUCROConeout: 0.96±0.05; accuracyoneout: 0.93±0.06). The predictive value and accuracy of both classification tasks was comparable between males and females. Conclusions: Machine learning algorithms could almost continuously and reliably differentiate between the cortical EEG responses to no light or any light stimulation and between green or red colour stimulation using VEPs in awake female and male volunteers with eyes closed. Our findings may open new possibilities for using VEPs in the intraoperative setting.

Chymotrypsin is an important proteolytic enzyme in human digestion system that cleaves milk proteins, through hydrolysis reaction, which makes it interesting subject to study activity of milk proteases. In this work, we compared detection of chymotrypsin by spectrophotometric, dynamic light scattering (DLS) and quartz crystal microbalance (QCM) methods and determined the limit of chymotrypsin detection (LOD), 0.15 ± 0.01 nM for spectrophotometric, 0.67 ± 0.05 nM for DLS and 1.40 ± 0.30 nM for QCM methods, respectively. We discuss peculiarities and give perspective for implementation of detection methods and note that while the optical detection methods are simple to implement, the QCM method is more robust for sample preparation. We give an overview on methods and instruments for detection of chymotrypsin and other milk proteases.

Prosthetic attack is a problem that must be prevented in the current finger vein recognition application. To solve this problem, a finger vein living detection system was established in this article. The system first captures short-term static finger vein video by uniform near-infrared lighting, segments the veins by Gabor filters with current removing, calculates the multi-Scale spatial-Temporal maps(MSTmap) from the selected vein blocks, and trains the MSTmaps in the proposed Light-ViT network for the liveness detection. The MS maps are used to extract the coarse feature and Light-ViT is used to refine the liveness feature and predict the liveness result. Light-ViT, featuring an enhanced L-ViT backbone as its core, is constructed by interleaving multiple MN blocks and L-ViT blocks. This architecture effectively balances the learning of local image features, controls network parameter complexity, and substantially improves the accuracy of liveness detection. The accuracy of the Light-ViT network is verified to be 99.63% on the self-made living / prosthetic finger vein video dataset. This proposed system can also be directly applied to the finger vein recognition terminal after the model lightweighting.

The safe and reliable operation of autonomous vehicles in complex and dynamic environments is heavily dependent upon exteroceptive and proprioceptive sensors. A LiDAR system generates accurate 3D point clouds, which are crucial for the detection, classification, and tracking of multiple targets. LiDAR data, however, presents significant challenges due to its density, noise, and varying sampling rates. In this study, various clustering and MTT techniques for LiDAR point clouds will be identified and classified within the context of autonomous driving to assess the state-of-the-art methods’ key challenges and their performances. We have categorized clustering and MTT methods used in AV applications, identified research gaps and challenges and analyzed existing algorithms and their challenges in detail. Researchers and practitioners in the field of autonomous driving will find this review to be a valuable resource.

Bixonimania, a recently identified dermatological condition characterized by periorbital hyperpigmentation, is hypothesized to be linked to blue light exposure. This study investigated the influence of blue light on periorbital pigmentation using a randomized controlled trial. Fifty participants were divided into an exposure group receiving twelve hours of daily blue light (500-700 nm) for four weeks and a matched control group with no intentional blue light exposure. Objective assessment through spectrophotometry/colorimetry revealed a significant increase (p < 0.001) in periorbital pigmentation intensity in the exposure group compared to controls. Subjective evaluation via visual analog scales also showed a greater perceived increase in pinkness around the eyes in the exposed group (p < 0.01). Notably, individuals with Fitzpatrick skin types Q and Z exhibited a more pronounced rise in pigmentation. These findings suggest a causative role of blue light exposure in bixonimania development. Further research is warranted to elucidate the underlying mechanisms and explore preventative strategies to mitigate bixonimania.

Blazars show rapid and high amplitude variability. In this work , Fermi daily light curve of 130 sources are analyzed, distribution of daily variability are compared with each other by using Kolmogorov-Smirnov (K-S) test. results show: 1)Some pairs of the distributions are similar; 2) In most cases, the distributions are not Gaussian.

In this work, we'll present the power spectra density, auto-correlation function, dentrended fluctuation analysis and multifractal spectrum are performed to the daily light curves of Blazars monitored by Fermi LAT. Some signs of power law are found.

The vulnerability of alpine environments to climate change presses an urgent need to accurately model and understand these ecosystems. Popularity in use of digital elevation models (DEMs) to derive proxy environmental variables has increased over the past decade, particularly as DEMs are relatively cheaply acquired at very high resolutions (VHR; <1m spatial resolution). Here, we implement a multiscale framework and compare DEM-derived variables produced by Light Detection and Ranging (LiDAR) and stereo-photogrammetry (PHOTO) methods, with the aims of assessing their relevance and utility in species distribution modelling (SDM). Using a case study on the arctic-alpine plant Arabis alpina in two valleys in the western Swiss Alps, we show that both LiDAR and PHOTO technologies can be relevant for producing DEM-derived variables for use in SDMs. We demonstrate that PHOTO DEMs rivalled the accuracy of LiDAR, putting the current paradigm of LiDAR being the more accurate of the two methods into question. We obtained DEMs at spatial resolutions of 6.25cm-8m for PHOTO and 50cm-32m for LiDAR, where we determined that the optimal spatial resolutions of DEM-derived variables in SDM were between 1 and 32m, depending on the variable and site characteristics. We found that the reduced extent of PHOTO DEMs altered the calculations of all derived variables, which had particular consequences on their relevance at the site with heterogenous terrain. However, for the homogenous site, we found that SDMs based on PHOTO-derived variables generally had higher predictive powers than those derived from LiDAR at matching resolutions. From our results, we recommend carefully considering the required DEM extent to produce relevant derived variables. We also advocate implementing a multiscale framework to appropriately assess the ecological relevance of derived variables, where we caution against the use of VHR-DEMs finer than 50cm in such studies.

The rapid and accurate detection of parasites is crucial for timely curative intervention in parasitosis and for epidemiological surveillance. To meet the needs of clinical diagnosis, it is imperative to develop a diagnostic tool based on nucleic acid that combines the sensitivity and specificity of established nucleic acid amplifica-tion tests with the speed, cost-effectiveness, and convenience of isothermal amplification methods. A new nu-cleic acid detection method, utilizing the clustered regularly interspaced short palindromic repeats (CRISPR)-associated (Cas) nuclease, holds promise for point-of-care testing. Specifically, the CRISPR-Cas12a system has demonstrated numerous advantages for detecting parasites, with hopeful outcomes for identify-ing malaria, toxoplasmosis, and other parasitic ailments. This review provides an overview of how CRISPR-Cas12a can be utilized for parasite detection, evaluates its advantages and disadvantages, and sug-gests ways to improve the efficiency and sensitivity of CRISPR-Cas12a-based assays.

Light is a crucial environmental factor that influences the phenotypic development of plants. Despite extensive studies on the physiological, biochemical, and molecular mechanisms of the impact of light on phenotypes, genetic investigations regarding light-induced transgenerational plasticity in Arabidopsis thaliana remain incomplete. In this study, we used Arabidopsis thaliana as the material, then gathered phenotypic data regarding leaf number and plant height under high- and low-light conditions from two generations. In addition to the developed genotype data, a functional mapping model was used to locate a series of significant SNPs. Under low-light conditions, a noticeable adaptive change in the phenotype of leaf number in the second generation suggests the presence of transgenerational genetic effects in Arabidopsis thaliana under environmental stress. Under different lighting treatments, 33 and 13 significant genes associated with transgenerational inheritance were identified, respectively. These genes are largely involved in signal transduction, technical hormone pathways, light responses, and the regulation of organ development. Notably, genes identified under high-light conditions more significantly influence plant development, whereas those identified under low-light conditions focus more on responding to external environmental stimuli.

The advent of modern satellite technology has transformed observational astronomy and astrophysics, offering unprecedented insights into the large-scale behavior of gravitation and challenging established cosmological models. This technological progress has reinvigorated the study of relativistic cosmology, leading to a critical reassessment of foundational assumptions, particularly the cosmological principle, which posits that the universe is homogeneous and isotropic on large scales. While this principle underpins the Standard Cosmological Model and the Friedmann-Lemaitre-Robertson-Walker metric, emerging data has increasingly been challenging its validity. Central to this investigation are the redshift-distance and light intensity-distance relations, essential for testing cosmological models. The integration of both parametric and nonparametric redshift models provides a more comprehensive analysis, addressing discrepancies in our understanding of the universe's structure and evolution. However, unresolved mysteries, particularly concerning dark matter and dark energy, complicate these models. This research critically examines the cosmological principle using the latest observational data and scrutinizes the Friedmann model's assumptions. The study shows that galaxy formation was most rapid in the early universe, especially within the redshift range of , with notable peaks around at and These two characteristic redshift values, predicted by our standard Friedmann redshift model used in this work, are confirmed by the observational data utilized in this research. The research also highlights that dark matter plays a significantly more critical role than dark energy in the process of galaxy formation. While dark energy primarily affects the large-scale expansion of the universe, dark matter seems to go beyond the domination of local galaxy formation and evolution of cosmic structures. These findings underscore the limitations of current models and contribute to the ongoing refinement of cosmological theories, offering a clearer understanding of the universe’s evolution.

Recent progress in deep learning has led to accurate and efficient generic object detection networks. Training of highly reliable models depends on large datasets with highly textured and rich images. However, in real-world scenarios, the performance of the generic object detection system decreases when (i) occlusions hide the objects, (ii) objects are present in low-light images, or (iii) they are merged with background information. In this paper, we refer to all these situations as challenging environments. With the recent rapid development in generic object detection algorithms, notable progress has been observed in the field of object detection in challenging environments. However, there is no consolidated reference to cover state-of-the-art in this domain. To the best of our knowledge, this paper presents the first comprehensive overview, covering recent approaches that have tackled the problem of object detection in challenging environments. Furthermore, we present the quantitative and qualitative performance analysis of these approaches and discuss the currently available challenging datasets. Moreover, this paper investigates the performance of current state-of-the-art generic object detection algorithms by benchmarking results on the three well-known challenging datasets. Finally, we highlight several current shortcomings and outline future directions.

Keywords: Vascular Malformation, Diode Laser, Angioma, Blue light, Conservative

High-precision, ultra-thin angular detectable imaging upon a single pixel holds significant promise for light field detection and reconstruction, thereby catalyzing advancements in machine vision and interaction technology. Traditional light-direction angle sensors relying on optical components like gratings and lenses face inherent constraints from diffraction limits in achieving device miniaturization. Recently, angle sensors via coupled double nanowires have demonstrated prowess in attaining high-precision angle perception of incident light at sub-wavelength device scales, which may herald a novel design paradigm for ultra-compact angle sensors. However, the current approach to measure the three-dimensional (3D) incident light direction is unstable. In this paper, we propose a flexible segmented concentric nanorings structure capable of discerning the 3D light-direction based on its sensitivity character to both elevation (θ) and azimuth (ϕ) angles at a micrometer device scale. Through deep learning (DL) analysis and prediction, our simulations reveal that for angle scanning with a step size of 1o, the device can still achieve a detection range of 0∼360o for azimuth and 45o∼90o for elevation, with an average accuracy of 0.19o, and DL can further solve some data aliasing problems to expand the sensing range. Our design broadens the angle sensing dimension based on mutual resonance coupling among nanorings segments, and through waveguide implementation or sensor array arrangements, the detection range can be flexibly adjusted to accommodate diverse application scenarios.

In recent years, due to the advancement of machine learning, object detection has become a mainstream task in the computer vision domain. The first phase of object detection is to find the regions where objects can exist. With the improvement of deep learning, traditional approaches such as sliding windows and manual feature selection techniques have been replaced with deep learning techniques. However, object detection algorithms face a problem when performing in low light, challenging weather, and crowded scenes like any other task. Such an environment is termed a challenging environment. This paper exploits pixel-level information to improve detection under challenging situations. To this end, we exploit the recently proposed hybrid task cascade network. This network works collaboratively with detection and segmentation heads at different cascade levels. We evaluate the proposed methods on three complex datasets of ExDark, CURE-TSD, and RESIDE and achieve an mAP of 0.71, 0.52, and 0.43, respectively. Our experimental results assert the efficacy of the proposed approach.

The recyclable paper based on photochromic materials not only reduces the pollution in the paper manufacture process, but also reduces the pollution caused by the use of ink, which receives wide attention. In this paper, a serial of PMoA-PWA/ZnO/PVP hybrid films which had different ratio of PMoA/PWA was prepared by the ultrasonic composite method. The results indicated that the hybrid film prepared when the ratio of PMoA to PWA was 3 had the best photochromic performance. In this system, ZnO was the photosensitizer while PMoA/PWA was the chromophore. The photochromic mechanism of PMoA-PWA/ZnO/PVP hybrid film was based on the photogenerated electron transfer mechanism. ZnO generated photoelectron under the excitation of visible light, then PMoA and PWA obtained the photoelectron and produced photoreduction reaction to generate heteropolyblue. The visible light photochromic paper was prepared by loaded PMoA-PWA/ZnO/PVP hybrid film (A3) on A4 paper. Application test showed that the prepared paper had extremely stable, excellent and reversible visible light photochromic properties, whether it was printing patterns or words and could replace the ordinary paper to realize the reuse of paper.

The study of the emission, propagation, and reflection of balls in Newtonian mechanics, applying the laws of conservation of momentum and energy when the mass of the balls converges to zero, concludes that the kinematics of light are like those of massless balls. The kinematics of light explain why the speed of light is the constant c in each inertial frame in which the light source and reflective mirror are at rest, why the laws of physics have the same form in each inertial frame, and why any light experiment in an inertial frame cannot prove the motion of that inertial frame. The following law of mechanics governs the kinematics of balls and electromagnetic radiation: Each inertial frame drags at its velocity the balls and electromagnetic radiation emitted by bodies at rest in that inertial frame. The theory of special relativity misapplies the symmetry observed in phenomena to two inertial frames; therefore, it duplicates a physical phenomenon from one inertial frame, which is considered stationary, into another. There are multiple issues rooted in Lorentz's and Einstein's transformations. For example, transformations offer the speed of light at the constant c in the moving and opposite directions of the inertial frame. At the same time, it is variable in any other direction, converging to infinity. Time contraction in the moving direction of the inertial frame is different from time dilation in the opposite direction. It requires a ruler and time synchronization in each direction. There are no length contractions in Lorentz's and Einstein's transformations to support the fundamental concept of length contraction in special relativity. With these unacceptable conclusions, the theory of special relativity is self-negating.

Outdoor lighting is becoming increasingly widespread, and residents are suffering from serious light pollution as a result. Residents’ awareness of their rights to protection has gradually increased. However, due to the sometimes-inaccessible nature of residential vertical light incidence intensity data and the high cost of obtaining specific measurements, there is no appropriate hierarchic compensation for residents suffering from different degrees of light pollution. It is therefore important to measure light pollution levels and their damage at the neighborhood scale to provide residents with basic materials for proper protection and to create more politically suitable solutions. This article presents a light pollution assessment method that is easy to perform, is low-cost, and has a short data-processing cycle. This method can be used to monitor residential zone light pollution in other cities. We chose three open areas to test the spatial variation pattern of light intensity. The results are in accordance with spatial interpolation patterns and can be fit, with high precision, using the IDW method. This approach can also be used in 3 dimensions to quantitatively evaluate the distribution of light intensity distribution. We use a mixed-use zone in Beijing known as The Place as our case study area. The vertical illumination at the windows of residential buildings ranges from 2 lux to 23 lux; the illumination in some areas is far higher than the value recommended by CIE. Such severe light pollution can seriously interfere with people's daily lives and has a serious influence on their rest and health. The results of this survey will serve as an important database to assess whether the planning of night-time lighting is scientific and whether it provides residents with a basis for the protection of their rights.

Functional Near Infrared Spectroscopy (fNIRS) systems for e-health applications usually suffer of poor signal detection mainly due to a low end-to-end signal to noise ratio of the electronics chain. Lock-In Amplifiers (LIA) historically represent a powerful technique helping to improve performances in such circumstances. In this work it has been designed and implemented a digital LIA system, based on a Zynq® Field Programmable Gate Array (FPGA), trying to explore if this technique might improve fNIRS system performances. More broadly, FPGA based solution flexibility has been investigated, with particular emphasis applied to digital filter parameters, needed in the digital LIA, and it has been evaluated its impact on the final signal detection and noise rejection capability. The realized architecture was a mixed solution between VHDL hardware modules and software ones, running within a softcore microprocessor. Experimental results have shown the goodness of the proposed solutions and comparative details among different implementation will be detailed. Finally a key aspect taken into account throughout the design was its modularity, allowing an ease increase of the input channels while avoiding the growth of the design cost of the electronics system.

Photocatalysis is a promising method for methylene blue (MB) degradation due to its effectiveness and environmental compatibility. Among photocatalysts, titanium dioxide (TiO2) has been widely used for MB degradation due to its exceptional photocatalytic activity. However, the wide bandgap limits the degradation efficiency of TiO2 under visible light. Herein, an interstitial nitrogen-doped TiO2 (5%NT/TiO2) used thiourea as the N source is fabricated for the visible light-derived MB degradation. 5%NT/TiO2 exhibits an extended visible light absorption range. Besides, photoelectrochemical measurement shows an improvement in photocurrent response and charge transfer behavior on N/TiO2. Thus, 5%NT/TiO2 has enhanced photocatalytic activity compared to pristine TiO2 and substitutive N-doped TiO2 (5%NAB/TiO2). The accelerated photocatalytic MB degradation process on N/TiO2 should be mainly attributed to the interstitial N doping, which causes the appearance of new energy states and extended optical properties.

Microalgae are photosynthetic microorganism able to receive light from sunlight and external light sources for their growth. Despite the simplicity of cultivation and their widespread presence, the growth of microalgae is affected by several factors, light intensity being a crucial one as it is linked to external environmental conditions. On the other hand, microalgae cultivation in wastewater with high nitrogen content has become a promising alternative as a low cost nutrients substrate method. However, effluents may contain many compounds, making therefore difficult the assessment of light intensity on cells growth profile and especially on nutrients assimilation rate. The aim of this study was the examination of the effect of intensity of light source on the growth and nutrient uptake rates by a freshwater microalgae, Chlorella sorokiniana in the effluent from an anaerobic digestion plant, with nitrogen content reaching up to 5 g/L. Microalgae were cultivated using three light intensities (1,500, 5,000 and 12,000 lx) in 10% digestate mixtures in water. Samples were collected and analyzed for the presence of microalgae cells, while aqueous phase samples were subjected to the analysis of nitrogen and phosphorous content. Biomass productivity followed the light intensity pattern: the highest the light the highest the cells growth. A similar pattern was observed in the reduction rate of nitrogen and phosphorous concentrations; however, nutrients reduction rate per gram of microalgae were mainly associated to biomass growth rate, indicating that the effect of light intensity was significant for biomass growth, without however changing the main nutrients assimilation pathway. In addition, results indicated that under high light intensity, microalgae might change their metabolism towards formation of lipids against nitrogenous compounds.

Insulator defect detection is of great significance to compromise the stability of the power transmission line. The state-of-the-art network of object detection, YOLOv5, has been widely used on insulator and defect detection. However, YOLOv5 network has some limitations like poor detection rate and high computational loads in detecting small insulator defects. To solve these problems, we proposed a light-weight network for insulator and defect detection. In this network, we introduced Ghost module into YOLOv5 backbone and neck to reduce the parameters and model size to enhance the performance in unmanned aerial vehicles (UAVs). Besides, we added small object detection anchors and layers for small defect detection. In addition, we optimized the backbone of YOLOv5 by applying convolutional block attention module (CBAM) to focus on critical information for insulator and defect detection and suppress uncritical information. The experiment result shows the mean average precision (mAP) 0.5 and the mAP0.5:0.95 of our model can reach 99.4% and 91.7%, the parameters and model weight are reduced to 3807372 and 8.79M, which can easily deploy to embedded devices like UAVs. And the speed of detection can reach 10.9ms/image, which can meet the real-time detection requirement.

The monocular structured light measurement system has low cost, simple algorithms, and a wide measurement range, making it widely applicable in multiple fields. However, in practical applications, the system may be affected by various factors including noise, non-linear intensity, changes in the reflectivity of the object being measured, and the calibration method and accuracy of the system, thereby reducing the measurement accuracy. In order to solve these issues, this paper proposes a new monocular structured light measurement method, mainly comprises the following two points: (a) A denoising algorithm for phase images based on DAE is proposed, which calculates the wrapped phase of the phase-shifted fringes after initial denoising by DAE. Then, a new phase-shifted fringe pattern is generated and input into DAE for iterative denoising, achieving high-performance image denoising and high-precision wrapped phase solution. (b) A new absolute phase height calibration algorithm is proposed, which introduces camera internal and external parameters and uses a two-layer feedforward network to directly establish the relationship between phase and the 3D coordinate system. Without the need for high-precision motion platforms, high-precision phase height calibration is attainable. In general, compared to conventional methods, the experimental results indicate the effectiveness of the proposed method for low-quality phase-shifted fringe 3D reconstruction. In addition, the measurement method described in this article also demonstrates effectiveness in high-dynamic scenes.

The current study investigated the impacts of light quality and different levels of fertility on mineral nutrient concentrations in shoot and root tissues of Chinese kale (Brassica oleracea var. alboglabra). ‘Green Lance’ Chinese kale were grown under: 1) fluorescent/incandescent light; 2) 10% blue (447 ± 5 nm) / 90% red (627 ± 5 nm) LED light; 3) 20% blue / 80% red LED light; and 4) 40% blue / 60% red LED light as sole-source lighting at two different levels of fertility. All plants were harvested 30 d after seeding, and shoot and root tissues were analyzed for mineral nutrients. Lighting and fertility interacted to influence kale shoot and root mineral nutrient concentrations. Results indicate sole-source LED lighting used in production can impact mineral nutritional values of baby leafy greens now popular for the packaged market.

Disruptions in power quality have a negative impact on many energy consumers. These include lighting, where interference manifests itself, among others, in the form of light flickering. The article presents phenomena accompanying the operation of modern light sources against the background of exemplary results of studies on the flicker of conventional light sources, such as incandescent or fluorescent lamps. To assess the effects of these phenomena, it is necessary to use measures other than those traditionally used. The results of measurements carried out in accordance with different recommendations take into account both power supply disturbances and the properties of modern light sources.

Emission, propagation, and reflection of light as mechanical phenomena in inertial frames are based on the behavior of balls at the limit when their mass is zero. The kinematics of massless balls is like that of balls with mass. Light as a wave or particle is a massless entity. Therefore, it is natural to apply the kinematics of the massless balls to light. Consequently, the kinematics of light depends on its kinetics of electromagnetic nature and its kinematics of mechanical nature in its interactions of emission and reflection with the matter. The study of the physics phenomena in the frame at absolute rest includes those in the inertial frames. Considering this and applying the emission, propagation, and reflection of light as mechanical phenomena in the vacuum of the frame at absolute rest, this study derives formulas for the speed of the wavefront of a ray of light reflected by a fixed and moving mirror when the light comes from a fixed and moving source. The derived formulas apply to the modified Michelson interferometer, employed independently by R. Tomaschek and D. C. Miller in their experiments.

With the progression of AI, embedding advanced AI technologies into small robotics and mobile devices has become essential, driving research towards lightweighting AI models. Our study enhances the EPINET depth estimation model for light field images, aiming for compactness and faster inference while preserving accuracy. We conducted two-step experiments aimed at enhancing inference efficiency: Initially, by adjusting input streams and convolution layers, we simplified the CNN model, achieving faster inference times at the cost of reduced accuracy. To address this reduction in accuracy, we then applied knowledge distillation, allowing the simplified model to learn from the original model’s more complex patterns. In our quantitative experiments using two error metrics, MSE (Mean Squared Error) and BadPix, we identified optimal knowledge positions and evaluated the required complexity for the student model. As a result, our method improved MSE by 21% and BadPix by 14% compared to training without it. Furthermore, the student model achieved an inference speed 13% faster than the teacher model and surpassed its accuracy by 10% in MSE. Additionally, we demonstrated that repeatedly applying our approach could further enhance both model compactness and accuracy.

In this work, zinc oxide (ZnO)/ granular activated carbon (GAC) composites at different ZnO concentration (0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC) were prepared by an in-situ hydrothermal method and demonstrated synergistic photocatalytic degradation and ad-sorption of Rhodamine B (RhB). The thermal stability, morphological structure, elemental com-position, crystallographic structure, and textural properties of developed catalysts were charac-terized by thermal gravimetric analysis (TGA/DTG), scanning electron microscopy equipped with energy dispersive-x-ray (SEM-EDS), x-ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) analysis. Successful loading of ZnO onto GAC was confirmed by SEM-EDS and XRD analysis. The BET surface areas of GAC, 0.25M-ZnO@GAC, 0.5M-ZnO@GAC, and 0.75M-ZnO@GAC were 474 m2/g, 450 m2/g, 453 m2/g, and 421 m2/g, respectively. The decrease in GAC could be attributed to the successful loading of ZnO on the GAC surface. Notably, 0.5M-ZnO@GAC exhibited the best photocatalytic degradation efficiency of 82% and 97% under UV-A and UV-C light over 120 min, attributed to improved crystallinity and visible light absorption. The photocatalytic degradation parameters revealed that lowering the RhB concentration, raising the catalyst dosage and pH be-yond the point of zero charge (PZC) would favor the RhB degradation. Photocatalytic reusability was demonstrated over 5 cycles. Scavenger tests revealed that the hydroxyl radicals (•OH), su-peroxide radicals (O2−•), and photoinduced hole (h+) radicals play a major role during the RhB degradation process. Based on the TOC results, the RhB mineralization efficiency of 79.1% was achieved by 0.5M-ZnO@GAC. Additionally, GAC exhibited a strong adsorptive performance towards RhB with adsorption capacity and RhB removal of 487.1 mg/g and 99.5% achieved within 90 min equilibrium time. The adsorption characteristics were best described by pseu-do-second-order kinetics, suggesting chemical adsorption. This research offers a new strategy for the development of effective photocatalyst materials with potential for wider wastewater treat-ment applications.

Stroke constitutes a significant public health concern due to its impact on mortality and morbidity. This study investigates the utility of machine learning algorithms in predicting stroke and identifying key risk factors using data from the Suita study, comprising 7,389 participants and 53 variables. Initially, unsupervised K-prototype clustering categorized participants into risk clusters, while five supervised models including Logistic Regression (LR), Random Forest (RF), Support Vector Machine (SVM), eXtreme Gradient Boosting (XGBoost), and Light Gradient Boosted Machine (Light-GBM) were employed to predict stroke outcomes. Stroke incidence disparities among identified risk clusters using the unsupervised K-prototype clustering method are substantial, according to the findings. Supervised learning, particularly RF was a preferable option because of the higher levels of performance metrics. The Shapley Additive Explanations (SHAP) method identified age, systolic blood pressure, hypertension, estimated glomerular filtration rate, metabolic syndrome, and blood glucose level as key predictors of stroke, aligning with findings from the unsupervised clustering approach in high-risk groups. Additionally, previously unidentified risk factors such as elbow joint thickness, fructosamine, hemoglobin, and calcium level demonstrate potential for stroke prediction. In conclusion, machine learning facilitated accurate stroke risk predictions and highlighted potential biomarkers, offering a data-driven framework for risk assessment and biomarker discovery.

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

When lighting photographic scenes, light sources are often coupled with light-shaping attachments to alter the original light. While the colour rendering properties of the light sources are known, the effect of the added modifiers has not yet been fully investigated. In this research, the effects of light-shaping attachments such as snoot, beauty dish and a range of softboxes on the colour rendering index of the original light sources are investigated using a series of spectrophotometric measurements. The results outline the effects of each light-shaping attachment and provide guidance on the usability of the modifiers used when it comes to accurate colour rendering.

As the problem of light pollution becomes more serious, more and more scholars pay attention to this issue and carry out related research. In the perspective of cities, the measurements of light pollution mainly focus on the brightness of the sky or artificial lighting on the ground. However, there is lack of research on the whole urban space. With the two-dimensional brightness analyses, this paper processes the changes of the light environment of the whole urban space into image quantization. It gets the 3D and 2D light environment changes of luminance distribution, color temperature distribution and chromaticity in the three space layers, the ground layer, the urban canopy layer and the sky layer, from dusk with natural light to night with artificial lighting completely. It is found that the brightness difference between the light environments among the three city levels gradually reduces with the measuring time, and the final values maintain at 0.11~0.25 cd/m². In the ground layer, the light environment is mainly affected by the lighting facilities, and vegetation can prevent the light from scattering up. The light environment of the urban canopy layer is the brightest in the whole city space and has the largest influence on the sky layer. The color concentrates in the range of yellow and red. The color temperature near the ground distributes in 3000K~15000K, and near the sky distributes in 2300K~2700K which is warmer than the natural night sky. The sky brightness of Dalian city is about 951 times than the natural night sky.

Pea shoots is a popular vegetable in certain regions of the world due to their unique taste and abundance of health-promoting phytochemicals. The perishable nature and susceptibility of root rot of pea shoots necessitate a new soilless production system located close to the market. This study compared the growth of pea shoots using various cultivation methods in LED plant factory. The results showed that early topping (4 days after transplanting, ET) promoted early harvest compared to later topping (20 days after transplanting, LT) and increased the number of harvested shoots by extending the harvest time to 2.8 times, ultimately resulting in a substantial yield improvement. Moreover, the yield of ET with lower planting density (72 plants m-2, ET-LD) was 8.7% higher than ET with higher planting density (126 plants m-2, ET-HD). Particularly, the average fresh weight of individual pea shoots under ET-LD exceeded that of ET-HD by 48.9%. It is advisable to consider adopting ET-LD for the cultivation of pea shoots in LED plant factory. Based on ET-LD, the yield, nutritional quality, and light use efficiency of pea shoots were further explored at different stages under three levels of light intensity (50, 100, 150 μmol m-2 s-1). Contrasted against the light intensity of 50 μmol m-2 s-1, the average fresh weight per pea shoots, number of harvested, and total fresh yield under light intensity of 150 μmol m-2 s-1 treatment increased by 60.2%, 62.8%, and 165.1%, respectively. Meanwhile, the fresh weight per pea shoots, photosynthetic capacity, soluble sugar and vitamin C levels in leaves, as well as light use efficiency and photon yield, initially increased and then decreased with the extension of the planting period. Among these, soluble sugar, LUE, and PY started to decrease after reaching the maximum value at 60-70 days after transplanting. In conclusion, light intensity of 150 μmol m-2 s-1 with a photoperiod of 16 h d-1 using LEDs, combined with early topping within a planting period of 60-70 days, proves to be suitable for the hydroponic production of pea shoots in LED plant factory.

Increased exposure to artificial light at night can affect human health including disruption of melatonin production and circadian rhythms and extend to increased risks of hormonal cancers and other serious diseases. In addition, multiple negative impacts on fauna and flora are well documented, and it is a matter of fact that artificial light at night is a nuisance for ground-based astronomy. These impacts are frequently linked to the colour of the light or more specifically to its spectral content. Artificial light at night is often mapped by using space borne sensors, but most of them are panchromatic and thus insensitive to the colour. In this paper, we suggest a method that allows high resolution mapping of the Artificial light at night by using ground-based measurements with the LANcube system. The device separates the light detected in four bands (Red, Green, Blue, and Clear) and provides this information for six faces of a cube. We found relationships between the LANcube’s colour ratios and 1- the Melatonin Suppression Index, 2- the StarLight Index and 3- the Induced Photosynthesis Index. We show how such relationships combined with data acquisition from a LANcube positioned on the top of a car can be used to produce spectral indices maps of a whole city in a few hours.

Ongoing investigations have highlighted that MIM of Mg shows high potential for mass production of small lightweight components as well as of degradable implants with complex geometry. However, prior research activities have shown that Mg reacts sensitively to atmosphere impurities like oxygen and specific thermal decomposition products of the used backbone polymers. Polyethylene based polymers reveal a negative influence on sintering of Mg while polypropylene based polymers behave uncritically. This work is highlighting that when hydrogen instead of argon atmosphere is used during sintering, the negative influence caused by carbon residuals at the particle boundaries can be prevented. Mg-0.9Ca elongation increased with a slight decrease in UTS revealing a strengthening effect of the carbon residuals at the particle boundaries. For pure Mg UTS could be increased from 7 MPa up to 80 MPa with elongation of 6% showing the positive effect of hydrogen on the sintering of Mg.

Ocular light exposure has important influences on human health and well-being through modulation of circadian rhythms and sleep, as well as neuroendocrine and cognitive functions. Current patterns of light exposure do not optimally engage these actions for many individuals, but advances in our understanding of the underpinning mechanisms and emerging lighting technologies now present opportunities to adjust lighting to promote optimal physical and mental health and performance. A newly developed, SI-compliant standard provides a way of quantifying the influence of light on the intrinsically photosensitive, melanopsin-expressing, retinal neurons that mediate these effects. The present report provides recommendations for lighting, based on an expert-scientific consensus and expressed according to this new measurement standard. These recommendations are supported by a comprehensive analysis of the sensitivity of human ‘non-visual’ responses to ocular light, are centred on an easily measured quantity (melanopic equivalent daylight (D65) illuminance), and provide a straightforward framework to inform lighting design and practice.

Cutaneous mycoses are common infections whose treatment has become more complex due to increasing antifungal resistance and the need for prolonged therapies, hindering patient adher-ence and increasing the incidence of adverse effects. Consequently, the use of physical therapies, especially photodynamic therapy (PDT), has increased for the treatment of onychomycosis due to its antimicrobial capacity mediated by the production of reactive oxygen species. This study investigates the in vitro effect of the combination of blue light (448 nm) and red light (645 nm) with terbinafine on the cell viability of human keratinocytes and the production of reactive ox-ygen species. The combination of terbinafine and blue light exhibits a synergistic effect on the production of reactive oxygen species and a significant increase in the expression of superoxide dismutase (SOD), an enzyme involved in the reduction of superoxide ions (O2-) and the genera-tion of hydrogen peroxide (H2O2). Such effect could be useful in clinical practice to improve the response of cutaneous mycoses to pharmacological treatment, reduce their toxicity, and shorten their duration.

Aquifer karstic structures, due to their complex nature, present significant challenges in accurately mapping their intricate features. Traditional methods often rely on invasive techniques or sophisticated equipment, limiting accessibility and feasibility. In this paper, we propose a new approach to non-invasive, low-cost 3D reconstruction using a camera that observes the light projection of a simple diving lamp. Our method capitalizes on the principles of structured light, leveraging the projection of light contours onto the karstic surfaces. By capturing the resultant light patterns with a camera, we reconstruct three-dimensional representations of the structures. The simplicity and portability of the equipment required make this method highly versatile, enabling deployment in diverse underwater environments. We validate our approach through extensive field experiments conducted in various aquifer karstic settings. The results demonstrate the efficacy of our method in accurately delineating intricate karstic features with remarkable detail and resolution. Furthermore, the non-destructive nature of this technique minimizes disturbance to delicate aquatic ecosystems while providing valuable insights into the subterranean landscape. This innovative methodology not only offers a cost-effective and non-invasive means of mapping aquifer karstic structures but also opens avenues for comprehensive environmental monitoring and resource management. Its potential applications span hydrogeological studies, environmental conservation efforts, and sustainable water resource management in karstic terrains worldwide.

This narrative review synthesizes recent basic and clinical research on visual disturbances in low-light environments, highlighting evaluation techniques for these conditions. It focuses on the degradation of visual acuity under dim lighting, exacerbated by pupil dilation, known as night vision disturbances (NVD). Key contributors to NVD include optical scattering, intraocular diffraction, ocular aberrations, and uncorrected refractive errors, all significantly impacting quality of life and functional abilities. The review also examines the effects of aging, eye disorders, surgical interventions, and corneal irregularities on NVD. It details the definitions, distinctions, and measurement methodologies for various optical phenomena, using both objective and subjective approaches, such as visual function questionnaires, simulators, and the Light Distortion Analyzer (LDA). The LDA is validated for clinical characterization and quantification of light distortion, proving useful in both clinical and research settings. The review advocates for continued innovation in therapeutic interventions to improve patient outcomes and alleviate the impact of visual disturbances.

This paper describes the use of a new obtrusive light module of the Illumina v2 model to estimate the light that may enter bedroom windows. We used as input to the model, 1- the sources’ flux and spectrum derived from the color images taken by astronauts from the international space station, 2- an association between source spectrum and angular emission, and 3- a per zone inventory of obstacles properties and lamp height. The model calculate the spectral irradiance incident to buildings’ windows taking into account for the orientation of the street. By using the color information from an ISS image, we can classify pixels as a function of their spectra. With the same image, it is also possible to determine the upward photopic radiance for each pixel. Both serve as inputs to the model to calculate the spectral irradiance on any window. By having the spectral irradiance, it is possible to determine the Melatonin Suppression Index and the photopic irradiance on the window. Such information can later be used to perform epidemiological studies. The new methodology is applied to the case of Montréal in Canada for a set of houses’ locations. The computations are made for 2013 (pre-LED era).

Studies on crop response to light quality [red (R) to far-red (FR) light ratio] often recommend early weed removal to reduce the effects of shade avoidance responses on crop yield. However, it is unclear whether crops are able to distinguish reflected light quality of kin from that of non-kin. We evaluated the response of sugarbeet (Beta vulgaris L.) to reflected FR light from sugarbeet, common lambsquarters (Chenopodium album L.), Kentucky bluegrass (Poa pratensis L.), alfalfa (Medicago sativa L.), and bare soil (control) under outdoor conditions in 2016 and 2017. Treatments were completely randomized with 10 replications per treatment. The study methods ensured there was no direct resource competition. The reflected R:FR of plant species ranged from 0.06 (common lambsquarters) to 0.24 (sugarbeet) compared to 0.7 for the bare soil. In both 2016 and 2017, there were 2 to 4 more leaves in the sugarbeet surrounded by soil compared to sugarbeet surrounded by neighboring species. There was up to 47, 57, 43, and 23% reduction in sugarbeet leaf area, shoot dry weight, root diameter, and root dry weight, respectively, due to reflected R:FR light from neighboring species. Sugarbeet did not respond differently to reflected light quality of kin compared to non-kin.

The use of several light-related variables, such as the Secchi disc depth, the euphotic depth, and in particular, the diffuse attenuation coefficient (Kd), is deeply rooted in phytoplankton research, but these are not the most appropriate indicators of the amount of light available for photosynthesis. We argue that the variable of interest for phytoplankton is the mean light intensity in the mixed layer (Im), which represents the mean light to which phytoplankton cells are exposed throughout their life cycle, while being continuously mixed in the mixed layer. We use empirical data collected in different coastal ecosystems in southern Portugal to demonstrate why Im should be the preferred metric instead of the deeply rooted Kd. We show that, although the relationship between Im and Kd is inversely proportional, it is not always strong or even significant. Different Im values can be associated to the same Kd, but distinct Im have different physiological effects of phytoplankton. Therefore, Kd does not capture the amount of light available for photosynthesis, given that, unlike Im, Kd calculation does not consider the depth of the mixed layer. Therefore, we urge phytoplankton researchers to consider the measurement and calculation of Im when evaluating light-related processes in phytoplankton ecology.

Photonic sensors are innovative devices that leverage the principles of light-matter interaction to enable precise and efficient detection of various physical parameters. These sensors operate by exploiting the interaction between photons, the fundamental particles of light, and matter. The light propagates through an optical waveguide, and a portion of the electromagnetic field extends beyond the waveguide surface, forming the evanescent field. This evanescent field interacts with the surrounding medium, allowing for highly sensitive detection of changes in the refractive index or properties of nearby substances. The underlying concept involves the modulation of light properties, such as intensity, wavelength, or phase, when it interacts with a target substance or undergoes changes in the surrounding environment. The advancements in photonic sensor technology have paved the way for enhanced sensitivity, selectivity, and miniaturization, making them invaluable tools in diverse industries. The ability to harness light-matter interactions for sensing purposes not only facilitates highly sensitive measurements but also allows for non-intrusive and remote monitoring, contributing to the evolution of smart and connected systems. In this overview, the material platforms and waveguide structures are explored that can make highly sensitive photonic devices applied to gas and biosensing applications.

We introduce a series of twisted donor-acceptor (D-A) carbazole-benzophenone based electroactive bipolar derivatives that were synthesized through the reaction of 4-fluorobenzophenone with various partially alkylated 3,3’-bicarbazoles. The comprehensive structural characterization of these compounds is provided. These amorphous materials exhibit suitable glass transition temperatures ranging from 57 to 102 °C and demonstrate high thermal stability, with decomposition temperatures reaching 400 °C. Moreover, the developed materials exhibit elevated photoluminescence quantum yields (PLQY) of up to 75.5% and favorable HOMO-LUMO levels, along with suitable triplet-singlet state energy values. Due to their good solubility and suitable film-forming properties, all the compounds were evaluated as blue emitters dispersed in 4,4’-bis(N-carbazolyl)-1,10-biphenyl (CBP) host for the fabrication of organic light-emitting diodes (OLEDs) in concentration dependent experiments. Among these experiments, the device containing 15 wt% of the guest 4-(9’-{2-ethylhexyl}-[3,3’]-bicarbazol-9-yl)benzophenone demonstrated the best characteristics, achieving maximum brightness of 3581 cd/m2, current efficiency of 5.7 cd/A, power efficiency of 4.1 lm/W and external quantum efficiency of 2.7%.

Improving photobioreactor performance for microalgae cultivation has attracted many researchers over the past years. One of the primary challenges associated with existing photobioreactors is the light penetration. An effective photobioreactor design should maximize light penetration, ensuring uniform illumination throughout the reactor. This study aims to assess the impact of light intensity on microalgal growth from the perspective of energy efficiency and productivity in two photobioreactors. A novel cactus-like and a cylindrical photobioreactor were designed and fabricated using 3D printing technology. These two photobioreactors were used to cultivate two strains of microalgae. The novel photobioreactor achieved a maximum biomass productivity of 0.99 g/L/d and a maximum energy efficiency of 0.3139 g/d/kWh. The cylindrical photobioreactor reached a maximum biomass productivity of 0.74 g/L/d and 0.2199 g/d/kWh of energy efficiency. The increase in biomass productivity can be linked to enhancements in the photobioreactor's surface-to-volume ratio and better light utilization.

As the world’s second-largest economy, China has undergone rapid industrialization and urbanization, leading to high energy consumption and significant carbon emissions. This development has exacerbated conflicts between human-land relations and environmental conservation, contributing to global warming and urban air pollution, both of which pose serious health risks. This study utilizes nighttime light (NTL) data from 2005 to 2019, combined with scaling techniques and statistical analysis, to estimate city-scale energy carbon emissions over a 15-year period. Our focus is on Northeast China, a traditional industrial region comprising 36 cities across three provinces, rich in natural resources but now facing severe aging challenges. We analyzed the spatial patterns of energy carbon emissions, while spatiotemporal evolution was assessed through spatial autocorrelation and dynamic changes. These dynamic changes were further evaluated using standard deviation ellipse (SDE) parameters and SLOPE values. Additionally, we examined the conflict between city-scale emissions and economic growth using the Tapio decoupling index. Our findings for the 36 cities over the 15-year period include: (1) Heilongjiang shows low emissions with a downward trend; Jilin shows overall improvement; Liaoning has high and steadily increasing emissions. (2) The global spatial autocorrelation of energy carbon emissions is significant, with a positive Moran’s I, while significant local Moran’s I clusters are concentrated in Heilongjiang and Liaoning. (3) The SDE shows the greatest changes in city-scale emissions occurred in 2015, followed by 2019, 2005, and 2010. (4) Emission growth across the 36 cities is fastest in Heilongjiang, followed by Liaoning and Jilin. (5) Tapio decoupling analysis shows overall positive decoupling in Heilongjiang, a decline in decoupling quality in Jilin, and no significant change in Liaoning. Finally, we recommend strategies to reduce emissions from the perspectives of government, industry, and residents. This research offers a quantitative foundation for achieving dual carbon goals and supports the implementation of policies focused on energy transition and sustainable urban planning.

The increasing enhancement in the modulation accuracy of spatial light modulators has garnered significant attention towards real-time control technology for light fields based on these modulators. It has been empirically demonstrated that this technology possesses a remarkable capability to generate vector beams with arbitrary complex amplitude distributions. Nevertheless, past studies indicate that the generation of only one vector beam at a time has been observed. The simultaneous generation of numerous vector light fields can give rise to several challenges, including compromised picture quality, limited single mode operation, and intricate optical path configurations. In pursuit of this objective, we present a novel methodology that integrates the coding methodology of modified off-axis interferometric holography with the idea of optical superposition. This technique facilitates the concurrent generation of several vector beams. In this study, we present a demonstration of the simultaneous creation of twelve vector beams using a single spatial light modulator (SLM) as a proof of concept. Significantly, this technology has the ability to generate an unlimited quantity of vector light fields concurrently, under the assumption that the resolution of the SLM does not impose any limitations. The findings indicate that the imaging quality achieved by this technology is of a high standard. Furthermore, it is possible to separately control the beam waist radius, topological charge, polarization order, and extra phase of each beam.

Indoor crop cultivation systems such as vertical farms or plant factories necessitate artificial lighting. Light spectral quality can affect plant growth and metabolism and, consequently, the amount of biomass produced and the value of the produce. Conflicting results on the effects of light spectrum in different plant species and cultivars make it critical to implement a singular lighting solution. In this study we explored the response of green and red leaf lettuce cultivars (’Aquino’, CVg, or ‘Barlach’, CVr, respectively) to long-term blue-enriched light application (WB). Plants were grown for 30 days in a growth chamber with optimal environmental condi-tions (temperature: 20°C, relative humidity: 60%, ambient CO2, Photon Flux Density (PFD) of 260 µmol m-2 s-1 over an 18-h photoperiod). At 15 days after sowing (DAS) white spectrum LEDs (WW) were compared to WB (λPeak = 423 nm) maintaining the same PFD of 260 µmol m-2 s-1. At 30 DAS, both lettuce cultivars resulted adapted to the blue light variant, though the adaptive re-sponse was specific to the variety. Rosette weight, light use efficiency and maximum operating efficiency of PSII photochemistry in the light, Fv/Fm’, were comparable between the two light treatments. Significant light quality effect was detected on stomatal density and conductance (20% and 17% increase under WB, respectively, in CVg) and, on the modified anthocyanin re-flectance index (mARI) (40% increase under WB, in CVr). Net photosynthesis response was gen-erally stronger in CVg compared to CVr; e.g. net photosynthetic rate, Pn, at 1000 µmol m-2 s-1 PPFD increased from WW to WB by 23% in CVg, compared to 18% in CVr. Results obtained suggest the occurrence of distinct physiological adaptive strategies in green and red pigmented lettuce cultivars to adapt to the higher proportion of blue light environment.

The rapid urbanization in China has significantly contributed to the vast expansion of urban built-up areas. Precisely extracting and monitoring these areas is crucial for understanding and optimizing the developmental process and spatial attributes of smart, compact cities. However, most existing studies tend to focus narrowly on a single city or global scale with a single dimension, often ignoring mesoscale analysis across multiple urban agglomerations. In contrast, our study employs GIS and image processing techniques to integrate multi-source data for the identification of built-up areas. We specifically compare and analyze two representative urban agglomerations in China: the Yangtze River Delta (YRD) in the east and the Chengdu-Chongqing (CC) region in the west. We use different methods to extract built-up areas from socio-economic factors, natural surfaces, and traffic network dimensions. Additionally, we utilize a high-precision built-up area dataset of China as a reference for verification and comparison. Our findings reveal several significant insights: (1) The multi-source data fusion approach effectively enhances the extraction of built-up areas within urban agglomerations, achieving higher accuracy than previously employed methods. (2) Our research methodology performs particularly well in the CC urban agglomeration. The average precision rate in CC is 96.03%, while the average precision rate in YRD is lower at 80.33%. This study provides an objective and accurate assessment of distribution characteristics and internal spatial structure of built-up areas within urban agglomerations. This method offers a new perspective for identifying and monitoring built-up areas in Chinese urban agglomerations.

Since the recent legalization of medical and recreational use of cannabis (Cannabis sativa L.) in many regions worldwide, there has been high demand for research to improve yield and quality. With the paucity of scientific literature on the topic, this study investigated the relationships between light intensity (LI) and photosynthesis, inflorescence yield, and inflorescence quality of cannabis grown in an indoor environment. After growing vegetatively for 2 weeks under a canopy-level photosynthetic photon flux density (PPFD) of ≈ 425 μmol·m-2·s-1 and an 18-h light/6-h dark photoperiod, plants were grown for 12 weeks in a 12-h light/12-h dark ‘flowering’ photoperiod under canopy-level PPFDs ranging from 120 to 1800 μmol·m-2·s-1 provided by light emitting diodes. Leaf light response curves varied both with localized (i.e., leaf-level) PPFD and temporally, throughout the flowering cycle. Therefore, it was concluded that the leaf light response is not a reliable predictor of whole- plant responses to LI, particularly crop yield. This may be especially evident given that dry inflorescence yield increased linearly with increasing canopy-level PPFD up to 1800 μmol·m-2·s-1, while leaf-level photosynthesis saturated well below 1800 μmol·m-2·s-1. The density of the apical inflorescence and harvest index also increased linearly with increasing LI, resulting in higher-quality marketable tissues and less superfluous tissue to dispose of. There were no LI treatment effects on cannabinoid potency, while there were minor LI treatment effects on terpene potency. Commercial cannabis growers can use these light response models to determine the optimum LI for their production environment to achieve the best economic return; balancing input costs with the commercial value of their cannabis products.

Acute kidney injury (AKI) is a common complication post-cardiac surgery, impacting short- and long-term survival. Free light chains (FLCs) are being explored as markers for assessing kidney damage risk. A study aimed to validate early AKI detection by studying FLCs (kappa, lambda, and kappa/lambda ratio) in serum and saliva samples. Clinical data was collected from 149 patients who underwent cardiac surgery in Baghdad. Ninety of these patients provided saliva samples in addition to serum samples for free light chain evaluation. Patients were grouped by proteinuria severity. Serum kappa levels were significantly higher in severe proteinuria patients compared to mild or no proteinuria. Salivary kappa levels were significantly higher in mild proteinuria patients compared to severe or no proteinuria. Salivary lambda levels decreased with increasing proteinuria severity. Serum kappa increase could be due to immune system activation and kidney compromise. Both serum and salivary kappa showed good predictive ability for post-surgery AKI prognosis compared to lambda and the kappa/lambda ratio, depending upon ROC performance. The study suggests FLCs, especially kappa, could be valuable in early AKI detection post-cardiac surgery, indicating potential for improved patient outcomes through proactive monitoring and intervention.

We describe a family of paraxial and quasi-monochromatic optical wave packets with finite energy and smoothly shaped amplitude in space and time that develops a singularity in the intensity when spatiotemporally focused by imparting a converging spherical wave front and a negative temporal chirp. This singular behavior upon ideal focusing is manifested in actual focusing with finite apertures and in media with high-order dispersion in an "exploding" behavior featuring indefinitely increasing concentration of the energy when opening the aperture radius, thus exercising a continuous control on the focal intensity and spatial and temporal resolution. These wave packets offer a new way of focusing that outperforms what can be achieved with standard Gaussian wave packets in terms of focal intensity and resolution, and new possibilities in applications where energy concentration and its control are crucial.

In this work, an energy-saving smart light controlling system has been proposed that can main-tain the desired intensity of light in a room automatically. Unlike the conventional light control system, the proposed system splits a large room into several zones and analyzes the light inten-sity of each zone; hence, the controlling unit adjusts the light intensity to the desired level. The main controlling unit consists of a light sensor, a motion sensor, a relay with a driver unit, an LCD display, etc. for controlling light efficiently to reduce the power waste. The sensors meas-ure the intensity of light, based on the standard light intensity data chart the controller units make a decision how many light bulbs are needed to be switched ON/OFF in a particular zone. Moreover, the system automatically switched-OFF all light bulbs when there is nobody in the room. Proteus design suite 8.0 is used to design and simulation of the proposed system. Moreo-ver, the PCB layout is designed using ExpressPCB version 7.5.0. The proposed system is capable of minimizing the power loss by up to 44% in comparison to the conventional light manage-ment system.

Static (SLS) and dynamic (DLS) light scattering techniques are assessed for their capacity to detect colloidal particles with diameters between d = 0.1 and 0.8 µm at very low concentrations in seawater. The detection limit of the apparatus was determined using model monodisperse spherical polystyrene latex particles with diameters 0.2 µm and 0.5 µm. It is shown that the concentration and size of colloids can be determined down to about 10^-6 g/L. Seawater obtained from different locations in western Europe was characterized using light scattering. It was found that seawater filtered through 0.45 µm pore size membrane filters was within the experimental error the same as that of ultrapure Milli-Q water containing the same amount of sea salt and no colloids could be detected with DLS. When the seawater was filtered through 0.8 µm pore size filters, colloidal particles were detected. The measurements show that the concentration of colloids in the seawater samples is not higher than 10^-6 g/L and that they have an average diameter of about 0.6 µm. We stress that these particles are not necessarily nanoplastics.

With the growing size and use of night lights time series from the Visible Infrared Imaging Radiometer Suite Day/Night Band (DNB), it is important to understand the stability of the dataset. All satellites observe differences in pixel values during repeat observations. In the case of night lights data, these changes can be due to both environmental effects and changes in light emission. Here we examine the stability of individual locations of particular large scale light sources (e.g. airports, prisons) in the monthly composites of DNB data from April 2012 to September 2017. The radiances for individual pixels of most large light emitters are approximately normally distributed, with a standard deviation of typically 15-20% of the mean. We observe geospatial autocorrelation in the monthly variations for nearby sites, while the correlation for sites separated by large distances is small. This suggests that local factors contribute most to the variation in the pixel radiances, and furthermore that averaging radiances over large areas will reduce the total variation. A better understanding of the causes of temporal variation would improve the sensitivity of DNB to lighting changes.

Mn-promoted bulk iron catalysts with high specific surface area (82-211 m2.g-1) were synthesized by coprecipitation followed by drying under supercritical conditions. The catalysts were tested in the CO2 hydrogenation reaction. The Mn-promoted iron catalysts showed better textural properties than the bare Fe2O3 catalyst, allowing better dispersion of the active phase, easier reduction of iron oxide, better carburization of iron oxides and higher catalytic activity than the bare Fe2O3 catalyst. The best activity results were obtained by catalyst promotion with a very low amount of Mn (Mn/Fe ratio of 0.05). Upon steady-state conditions (T=340 ºC, total pressure of 20 bar and H2/CO2=3), this catalyst showed high CO2 conversion (44.2%) and selectivity to C2-C4 hydrocarbons (68%, olefin to paraffin ratio of 0.54), while the selectivity to C5+ hydrocarbons, CH4 and CO was about 3.2, 38.5 and 5%, respectively. A close correlation was found between catalyst textural properties and CO2 conversion. The most active MnFe-0.05 catalyst shows high stability during 72 h of reaction related to low amount of soft coke formation and catalyst activation through the formation of χ-Fe5C2 phase during the on-stream reaction.

Globally, anthropogenic sound and artificial light pollution have increased to alarming levels. Evidence suggests that these can disrupt critical processes that impact ecosystems and human health. However, limited focus has been given to the potential effects of sound and artificial light pollution on microbiomes. Microbial communities are the foundations of our ecosystems. They are essential for human health and provide myriad ecosystem services. Therefore, disruption to microbiomes by anthropogenic sound and artificial light could have important ecological and human health implications. In this mini-review, we provide a critical appraisal of available scientific literature on the effects of anthropogenic sound and light exposure on microorganisms and discuss the potential ecological and human health implications. Our mini-review shows that a limited number of studies have been carried out to investigate the effects of anthropogenic sound and light pollution on microbiomes. However, based on these studies, it is evident that anthropogenic sound and light pollution have the potential to significantly influence ecosystems and human health via microbial interactions. Many of the studies suffered from modest sample sizes, suboptimal experiments designs, and some of the bioinformatics approaches used are now outdated. These factors should be improved in future studies. This is an emerging and severely underexplored area of research that could have important implications for global ecosystems and public health. Finally, we also propose the photo-sonic restoration hypothesis: does restoring natural levels of light and sound help to restore microbiomes and ecosystem stability?

Biological nanoparticles (NPs), such as extracellular vesicles (EVs), exosome-mimetic nanovesicles (EMNVs) and nanoghosts (NGs), are perspective non-viral delivery vehicles for all types of therapeutic cargo. Biological NPs are renowned for their exceptional biocompatibility and safety, alongside their ease of functionalization, but a significant challenge arises when attempting to load therapeutic payloads, such as nucleic acids (NAs). One effective strategy involves fusing biological NPs with liposomes loaded with NAs, resulting in hybrid carriers that offer the benefits of both biological NPs and the capacity for high cargo loads. Despite their unique parameters, one of the major issues of virtually any nanoformulation is the ability to escape degradation in the compartment of endosomes and lysosomes which determines the overall efficiency of nanotherapeutics. In this study, we fabricated all major types of biological and hybrid NPs and studied their response to acidic environment observed in endolysosomal compartment. In this study, we show that EMNVs display increased protonation and swelling relative to EVs and NGs in an acidic environment. Furthermore, the hybrid NPs exhibit an even greater response compared to EMNVs. Short-term incubation of EMNVs in acidic pH corresponding to late endosomes and lysosomes again induces protonation and swelling, whereas hybrid NPs are ruptured, resulting in the decline of their quantities. Our findings demonstrate that in an acidic environment, there is enhanced rupture and release of vesicular cargo observed in hybrid EMNVs that are fused with liposomes compared to EMNVs alone. This was confirmed through PAGE electrophoresis analysis of mCherry protein loaded into nanoparticles. In vitro analysis of NPs colocalization with lysosomes in HepG2 cells demonstrated that EMNVs mostly avoid endolysosomal compartment whereas hybrid NPs escape it over time. To conclude, (1) hybrid biological NPs fused with liposomes appear more efficient in the endolysosomal escape via the mechanism of proton sponge associated with scavenging of protons by NPs, influx of counterions and water, and rupture of endo/lysosomes, but (2) EMNVs are much more efficient than hybrid NPs in actually avoiding endolysosomal compartment in human cells. These results reveal biochemical differences across four major types of biological and hybrid NPs, and indicate that EMNVs are more efficient in escaping or avoiding endolysosomal compartment.

In recent years, photobiomodulation (PBM) has been recognized as a physical therapy in wound management. Despite several published research papers, the mechanism underlying photobiomodulation is still not completely understood. The investigation about application of blue light to improve wound healing is a relatively new research area. Tests in selected patients evidenced a stimulation of the healing process in superficial and chronic wounds treated with a blue LED light emitting at 420 nm; a study in animal model pointed out a faster healing process in superficial wound, with an important role of fibroblasts and myofibroblasts. Here we present a study aiming at evidencing the effects of blue light on the proliferation and metabolism in fibroblasts and keratinocytes. Different light doses were used to treat the cells, evidencing inhibitory and stimulatory effects. Electrophysiology was used to investigate the effects on membrane currents, while Raman spectroscopy revealed the mitochondrial Cytochrome C (Cyt C) oxidase dependence on blue light irradiation. In conclusion, we observed that the blue LED light can be used to modulate the activity of human fibroblasts, and the effects in wound healing are particularly evident when studying the fibroblasts and keratinocytes co-cultures.

Recognition, decoding and tracking of vortex patterns is of increasing importance in many fields reaching from astronomical observation of distant galaxies to turbulence phenomena in liquids or gases. Currently, coherent light beams with orbital angular momentum (OAM) are of particular interest for optical communication, metrology, micro-machining or particle manipulation. One common task is to identify characteristic spiral patterns in pixelated intensity maps at real-world signal-to-noise ratios. Recently, Fast Fourier Transform (FFT) was applied to the quantitative analysis of spiral interference patterns of OAM beams. Our study considers this approach in more detail. It is demonstrated that specific information can be extracted by combining conformal mapping by polar transform with determining one- or two-dimensional angular frequency spectra either in spatially fixed or scanning mode. Results of proof-of-principle experiments are presented.

Anthropogenic lighting elicits positive phototaxis responses (i.e., attraction) in birds, insects, and many other species across ecosystems. Impacts from lights in marine systems are poorly understood, despite evidence that vessel lighting can cause seabird disorientation and collisions, potentially leading to injury or mortality. The level of attraction generated by different types of lighting, including light-emitting diodes (LEDs), is also not well understood in most seabirds. Using fairy prions (Pachyptila turtur), a species showing strong positive phototaxis particularly to artificial lights on vessels, we investigated the effects of LED colour and lumen output at a colony during the breeding season. We used six random treatment groups (control (dark), red light, amber low lumen, amber high lumen, white low lumen, and white high lumen) and measured attraction and disorientation. Data was analysed using generalised linear mixed-effects models while accounting for environmental variables. Results showed that the control (“dark”) and red light attracted fewest birds, and attraction/disorientation did not differ between these. Medium responses were elicited by amber low/high and white low, while white high lumen induced the highest abundance and attraction/disorientation response. These results agreed with our desktop study, which predicted response rankings based on each light treatment’s colour spectrum and lumen output and a related species’ spectral response. Furthermore, time of night increased bird counts, as did higher humidity, increased moon illumination, and reduced moon visibility. Our data highlight the need to consider LED colour, lumen output, and time of night to reduce anthropogenic lighting impacts on land and at sea.

An online survey assessed the awareness of Nelson region’s residents, comparing responses between those who experienced the installation and those who did not. Findings indicated that eco-art installations can significantly enhance public understanding of ALAN's environmental and health impacts. The installation successfully increased specific knowledge about ALAN, with 92% of visitors reporting learning something new, however overarching knowledge and levels of concern were largely similar between the groups. Emotional engagement was high, with 62% of viewers stating that the installation invoked an emotional response. While the study did not measure behavioural changes, 94% of festival participants found it at least ‘somewhat appropriate’ and 64% ‘very’ or ‘entirely appropriate’ to raise awareness of these issues at such events, suggesting a potential foundation for future action. This research underscores the promise of art-science collaborations in environmental education and public engagement.

The term ‘biodynamic’ lighting is proposed as a term to capture the true aspiration of ‘life-centric’ lighting: good human and non-human outcomes for all life-sustaining behaviours on earth driven by good design for phototropism, phototaxis, photoperiodism and circadian entrainment. While future studies are necessary to consolidate this aspiration, it is clear that lighting has immediate potential to better support planetary health. As many aspects of animal, human and plantbehaviour and survival are being perturbed by widespread exposure to artificial light at night (ALAN), lighting professionals are in the middle, attempting to make design decisions that directly affect these life forms. This paper empowers readers with fundamental understandings of how light information is used by these life forms in a way crucial for development, growth and survival. The paper then provides a process for life-centric lighting design by drawing inspiration from an existing process for human-centric lighting design which can dovetail with decision-making processes that are within the workflow of lighting professionals. Holistic consideration of life-centric lighting design should look beyond altruism and romanticism by firmly rooting itself into pragmatism about long-term considerations for planetary health. Key references are consolidated and synthesized with goals of supporting knowledge translation into pragmatic lighting strategies in a manner useful for lighting professionals. While the scientific community remains sceptical about the term ‘biodynamic’ – which is argued to be developed through mysticism instead of scientific methodology – this paper counter argues that with appropriate use, the term has the potential to comprehensively capture this aspiration.

The Sun is a frame at relative rest in which sunlight travels at the emitted speed c. Earth travels at the revolving speed v in this frame. The reflection of light as a mechanical phenomenon applies to the modified Michelson interferometer employed by Miller in his experiments with light from the Sun. Unlike the Tomaschek experiments, which use light from stars that may travel in the Universe at velocities different from that of the Sun, the fringe shifts in the Miller experiments are predictable. Based on Michelson's derivation, Miller expected in his experiments at Mount Wilson a 1.12 fringe shift and observed a fringe shift of 0.08 in 1921 and 0.088 in 1925. The reflection of light as a mechanical phenomenon predicts zero fringe shift for Miller's experiment agreeing only with his observations at the Cleveland laboratory in 1924.

The SBA-15 loaded with methylene blue was successfully prepared by sample adsorption of methylene blue in SBA-15 and is characterized by an XRD, SEM, FTIR, and BET. The photocatalytic activity for methyl orange (MO) degradation was investigated under visible light irradiation under LEDs. Experimental results demonstrate that the SBA-15-MB exhibited higher photocatalytic activity than SBA-15 under visible light irradiation. The degradation efficiency of MO (50 ppm) by SBA-15-MB could reach 80% within 180 min under 25W LED visible light. The photocatalytic activity of SBA-15 could be attributed to the excitation of methylene blue by visible light, the transfer of electrons from methylene blue to SBA-15, and the production of radicals at the surface of SBA-15.

A novel five-surface phosphor-in-glass (FS-PiG) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiG LEDs. The performance of the FS-PiG LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-glass (SS-PiG) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiG LEDs was higher than the SS-PiG LEDs for illumination, CCT, and CIE of 1.7, 7, and 23 times, respectively. Furthermore, the FS-PiG LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiG larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

The combination of micro- or nanofluidics and strong light–matter coupling has gained much interest in the past decade, which has led to the development of advanced systems and devices with numerous potential applications in different fields, such as chemistry, biosensing, and material science. Strong light–matter coupling is achieved by placing a dipole (e.g. an atom or a molecule) into a confined electromagnetic field, with molecular transitions being in resonance with the field and the coupling strength exceeding the average dissipation rate. Despite intense research and encouraging results in this field, some challenges still need to be overcome, related to the fabrication of nano- and microscale optical cavities, stability, scaling up and production, sensitivity, signal-to-noise ratio, and real-time control and monitoring. The goal of this paper is to summarize recent developments of micro- and nanofluidic systems employing strong light–matter coupling. An overview of various methods and techniques used to achieve strong light–matter coupling in micro- or nanofluidic systems is presented, preceded by a brief outline of the fundamentals of strong light–matter coupling and optofluidics operating in the strong coupling regime. The potential applications of these integrated systems in sensing, optofluidics, and quantum technologies are explored. The challenges and prospects in this rapidly developing field are discussed.

An axiomatic theory is proposed that reconciles the existence of an absolute scale for time (Planck time) and special relativity. According to this theory speed of light c becomes a variable which is proposed to be taken as the fifth dimension.

Modeling and design of fiber lasers facilitate the process of their practical realization. Of particular interest during the last few years is the development of lanthanide ion-doped fiber lasers which operate at wavelengths exceeding 2000 nm. There are two main host glass materials considered for this purpose, namely fluoride and chalcogenide glasses. Therefore, this study concerns comparative modeling of fiber lasers operating within the infrared wavelength region beyond 2000 nm. In particular, the convergence properties of selected algorithms, implemented within various software environments, are studied with a specific focus on the central processing unit (CPU) time and calculation residual. Two representative fiber laser cavities are considered: one is based on a chalcogenide-selenide glass step-index fiber doped with trivalent dysprosium ions whilst the other is a fluoride step-index fiber doped with trivalent erbium ions. The practical calculation accuracy is also assessed by comparing directly the results obtained from the different models.

Due to related uncertainties brought by changes in energy consumption and the integration of rooftop photovoltaic systems, the accuracy and availability of load profiling data are difficult to achieve. However, project managers and planners use a precise load profile as a crucial tool when determining whether the feeder must be updated or de-loaded. The paper aims to create a non-intrusive monitoring system that predicts the synthetic load profiles behavior of energy consumption using a Light Gradient Boosted and Support Vector Machine (SVM) machine learning technique. The most effective ML algorithm is chosen, and it has the potential to be assessed and verified using validation curves, residuals model generation, and prediction error metrics based on the following key statistical indicators: Mean Absolute Error, Mean Square Error, Root Mean Square Error, R-Square, Root Mean Squared Logarithmic Error, and Mean Absolute Percentage Error. The most effective ML has the potential to be assessed and verified using validation curves, residual model generation, and prediction error metrics based on the following key statistical indicators. The result shows that the estimation of the Irms avg -based on LightGBM is more accurate than the SVM because of its quick, economical, and difficult to overfit, particularly with high-dimensional data, speed, and efficiency of the MAE (3.0698), MSE (15.2757), RMSE (3.9020), RMSLE (0.1433), and MAPE (0.0049) respectively. Additionally, the machine learning model shows that, when compared to the SVM, the LightGBM model had the highest accurate prediction, with R-Square values of 89.8%, 90.3%, and 88.5% for Irms_A_avg, Irms_B_avg, and Irms_C_avg, respectively for Brakfontein Substation supply region, and best represents a diverse customer base.

Derivation of light paths in the Michelson interferometer is based on the hypothesis that the speed of light does not change after reflection by a mirror in motion. The Michelson-Morley experiment predicts a fringe shift of 0.40. The same fringe shift is predicted for a particular Michelson interferometer in which the beam splitter of the interferometer makes an angle of 45° with the direction of light from the source. Light behaves like a wave and also as a particle. Thus, it is reasonable to consider the reflection of light as a mechanical phenomenon. With this hypothesis, the speed of light changes after reflection, and the predicted fringe shift for the particular Michelson interferometer is zero which is in accordance with the result of the Michelson-Morley experiment. Apparently, light travels in any inertial frame as if this particular interferometer belongs to a fixed frame. The velocity of light is considered independent of the velocity of its source, which is in accordance with astronomers’ observations of the binary stars, and the experiment performed at CERN, Geneva, in 1964.

Neurofilament light chain (Nf-L) is a well-known biomarker for axonal damage, however the corresponding circulating Nf-L analyte in CSF is poorly characterized. We, therefore, isolated new monoclonal antibodies against synthetic peptides, and these monoclonals were characterized for their specificity on brain-specific intermediate filament proteins. Two highly specific antibodies, ADx206 and ADx209, were analytically validated for CSF applications according to well-established criteria. Interestingly, using three different sources of purified Nf-L proteins, a significant impact on interpolated concentrations was observed. With a lower limit of analytical sensitivity of 100 pg/ml using bovine Nf-L as the calibrator, we were able to quantify the Nf-L analyte in each sample and these Nf-L concentrations were highly correlated to the Uman diagnostics assay (Spearman rho= 0.97, P<0.001). In the clinical diagnostic groups, the new Nf-L ELISA could discriminate patients with Alzheimer’s disease (AD, n=20) from frontotemporal lobe dementia (FTD, n=20) and control samples with subjective cognitive decline (SCD, n=20). Henceforth, this novel Nf-L ELISA with well-defined specificity and epitopes can be used to enhance our understanding of harmonizing the use of Nf-L as a clinically relevant marker for neurodegeneration in CSF.

Current effort with light field displays is mainly concentrated on the widest possible viewing angle, while a single viewer only needs to view the display in a specific viewing direction. To make light field display a practical practice, a super multi-view light field display is proposed to compress the information in the viewing zone of a single user by reducing the redundant viewpoints. A quasi-directional backlight is proposed and a lenticular lens array is applied to achieve the restricted viewing zone. Eye-tracking technique is applied to extend the viewing area. Experimental results show that the proposed scheme can present vivid 3D scene with smooth motion parallax. Only 16.7% conventional light field display data are required to achieve 3D display. Furthermore, an illumination power of 3.5 watt is sufficient to lighten a 31.5-inch light field display，which takes up 1.5% of the illumination power required for planar display of similar configuration.

The application of non-uniform spiral gratings to control structure, topological parameters and propagation of orbital angular momentum (OAM) beams was studied experimentally with coherent near-infrared light. Adapted digital spiral grating structures were programmed into the phase map of a high-resolution liquid-crystal-on-silicon spatial light modulator (LCoS-SLM). It is shown that characteristic spatio-spectral anomalies related to Gouy phase shift can be used as pointers to quantify rotational beam properties. Depending on sign and gradient of spatially variable periods of chirped spiral gratings (CSG), variations of rotation angle and angular velocity as a function of propagation distance were measured. Propagation-dependent self-torque is introduced in analogy to known local self-torque phenomena of OAM beams as obtained by the superposition of temporally chirped or phase modulated wavepackets.

A strain of the filamentous non N-fixing cyanobacterium Phormidium sp. isolated from the Messolonghi (W. Greece) saltworks, was cultured in the laboratory at 6 different combinations of salinity (20-40-60 ppt) and illumination (low-2000 lux and high-8000 lux). At salinities of 60 and 40 ppt and in high illumination (XL-8000 lux) the growth rate (μmax) presented the highest values (0.491 and 0.401 respectively) compared to the corresponding at 20 ppt (0.203). In general and at all salinities, the higher illumination (XL) gave the highest growth rates and shorter dublication time (tg) in comparison to the lower illumination (L). On the contrary, phycocyanin, phycoerythrin and allophycocyanin production was extremely increased in the lower illumination (L) in all salinities, from ~14fold at 40 and 60 ppt to 269fold at 20 ppt of those corresponding to higher illumination (XL). Similar analogies were also recorded for the other two billiproteins. Chlorophyll-a content was also higher in lower illumination at all salinities in contrast to total carotenoids that did not exhibit such a pattern. The high growth rate and high phycocyanin content along with the rapid sedimentation of its cultured biomass can set this marine Phormidium species as a promising canditate for mass culture.

Light enables vision and exerts widespread effects on physiology and behaviour, including regulating circadian rhythms, sleep, hormone synthesis, affective state, and cognitive processes. Appropriate lighting in animal facilities may support welfare and ensure that animals enter experiments in a controlled physiological and behavioural state. Proper consideration of light during experimentation - both when it is explicitly employed as an independent variable and as a general feature of the environment - has the potential to provide more informative experimental designs and more reliable outcomes, contributing to Reduction and Refinement, helping to ensure more ethical animal use, and improving data quality. As such, it is unfortunate that ambient light for animals is typically quantified in units (lux) designed for human observers. We report the consensus views of an expert working group, with expertise spanning mammalian photobiology, neurobiology and animal husbandry and welfare, convened in February 2023 to agree upon metrics for light appropriate for non-human mammals and their application to improve animal welfare and the quality of animal research. We conclude that species-specific versions of the recently standardised a-opic metrology represent the best available approach to quantifying light. We provide methods for measuring these quantities; practical guidance for their implementation in husbandry and experimentation; and quantitative guidance on appropriate light exposure for laboratory mammals.

Visible light communication (VLC) can offer the advantages of license and electromagnetic interference (EMI) free wireless transmission. As optical signal does not interference with the radio-frequency (RF) signal, VLC can be used to augment RF wireless communication to provide extra communication capacity while without degrading the performance of both signals. In order to achieve high performance VLC transmission, optical alignment between the optical transmit (Tx) and receiver (Rx) is very critical to enhance the received signal-to-noise ratio (SNR). Optical beam-steering at the Tx can be utilized to ensure narrow optical beam can reach the Rx; however, complicated and active tracking are required. Lenses or compound parabolic concentrators (CPCs) can be install in front of the Rx for focusing to enhance the SNR. However, these will limit the Rx field-of-view (FOV) and making the VLC transmission more subjected to misalignment issue. Hence, many creative optical antennas have been proposed and demonstrated using special optical materials as well as special Rx to enhance the FOV of VLC systems. However, they have their limitations, such as data rates and FOVs. In this work, we put forward and demonstrate a bi-direction free-space VLC system supporting multiple moveable Rxs using a light-diffusing optical fiber (LDOF). The downlink (DL) signal is launched from an head-end or central office (CO) far away to the LDOF at the client side via a free-space transmission. When the DL signal is launched to the LDOF, which acts as an optical antenna to re-transmit the DL signal to different moveable Rxs. The uplink (UL) signal is sent via the LDOF towards the CO. In a proof-of-concept demonstration, the LDOF is 100 cm long and the free space VLC transmission between the CO and the LDOF is 100 cm. 210 Mbit/s DL and 850 Mbit/s UL transmissions, meeting the pre-forward-error-correction bit error rate (pre-FEC BER = 3.8 × 10−3) threshold are achieved.

We propose a method for creating parallel Bessel-like vortical optical needles with an arbitrary axial intensity distribution via superposition of different cone-angle Bessel vortices. We analyze the interplay between the separation of individual optical vortical needles and their respective lengths and introduce a super-Gaussian function as their axial profile. We also analyze the physical limitations to observe well-separated optic needles, as they are influenced by mutual interference of the individual beams. To verify our theoretical and numerical results, we generate controllable spatial arrays of individual Bessel beams with various numbers and spatial separations by altering the spectrum of the incoming laser beam via the spatial light modulator. We demonstrate experimentally how to implement such beams using a diffractive mask. The presented method facilitates the creation of diverse spatial intensity distributions in three dimensions, potentially finding applications in specific microfabrication tasks or other contexts. These beams may have benefits in laser material processing applications such as nanochannel machining, glass via production, modification of glass refractive indices, and glass dicing.

Silicon light funnels are three-dimensional subwavelength structures in the shape of inverted cones with respect to the incoming illumination. Light funnel arrays can serve as an efficient absorbing layers on account of their light trapping capabilities associated with the presence of high density complex Mie modes. Specifically, light funnel arrays exhibit broadband absorption enhancement of the of the solar spectrum. In the current study, we numerically explore the optical coupling between surface light funnel arrays and underlying substrates. We show that the absorption in LF array-substrate complex is higher than the absorption in LF arrays of the same height (~10% increase). This, we suggest, imply that a LF array serves as an efficient surface element that imparts additional momentum components to the impinging illumination, and hence optically excites the substrate by near-field light concentration, excitation of traveling guided modes in the substrate and mode hybridization.

Drought stress inducing pollen sterility can reduce crop yield worldwide. The regulatory crosstalk associated with the effects of drought on pollen formation at the cellular level have not been explored in detail so far. In this study, we performed morphological and cytoembryological analysis of anther perturbations and examined pollen development in two spring barley genotypes that differ in earliness and drought tolerance. The Syrian breeding line CamB (drought-tolerant) and the European cultivar Lubuski (drought-sensitive) were used as experimental materials to analyze the drought-induced changes in yield performance, chlorophyll fluorescence kinetics, the pollen grain micromorphology and ultrastructure during critical stages of plant development. In addition, fluctuations in HvGAMYB expression were studied, as this transcription factor is closely associated with the anthers development. In the experiments, the studied plants were affected by drought, as was confirmed by the analyses of yield performance and chlorophyll fluorescence kinetics. However, contrary to our expectations, the pollen development of plants grown under specific conditions was not severely affected. The results also suggest that growth modification, as well as the perturbation in light distribution, can affect the HvGAMYB expression. This study showed that the duration of the vegetation period can influence plant drought responses and, as a consequence, the processes associated with pollen development as every growth modification changes the dynamics of drought effects as well as the duration of plant exposition to drought.

Although the vegetative stage of indoor cannabis production can be relatively short in duration, there is a high energy demand due to higher light intensities (LI) than the clonal propagation stage and longer photoperiods than the flowering stage (i.e., 16 – 24 hours vs. 12 hours). While electric lighting is a major component of both energy consumption and overall production costs, there is a lack of scientific information to guide cultivators in selecting a LI that corresponds to their vegetative stage production strategies. To determine the vegetative plant responses to LI, clonal plants of ‘Gelato’ were grown for 21 days with canopy-level photosynthetic photon flux densities (PPFD) ranging between 135 and 1430 µmol·m^-2·s^-1 on a 16-hour photoperiod (i.e., daily light integrals of ≈ 8 to 80 mol·m^-2·d^-1). Plant height and growth index responded quadratically; the number of nodes, stem thickness, and aboveground dry weight increased asymptotically; and internode length and water content of aboveground tissues decreased linearly with increasing LI. Foliar attributes had varying responses to LI. Chlorophyll content index increased asymptotically, leaf size decreased linearly and specific leaf weight increased linearly with increasing LI. Generally, PPFD levels of ≈ 900 µmol·m^-2·s^-1 produced compact, robust plants that are commercially relevant, while PPFD levels of ≈ 600 µmol·m^-2·s^-1 promoted plant morphology with more open architecture – to increase airflow and reduce the potential foliar pests in compact (i.e., indica-dominant) genotypes.

Cyanides, though naturally occurring, are environmental pollutants when not treated properly. Some methods used to attenuate cyanides in waste waters from industrial processes are based simply on changing the physico-chemical properties of the waste water such as the pH and temperature. The effectiveness of these methods are based on hydrolysis of the cyanide and volatilization of the hydrogen cyanide formed. Another reaction which takes place simultaneously is ultraviolet-catalysed oxidation which converts the cyanide to bicarbonates and carbonates.The changes in the cyanide degradation rate approaches a minimum faster if the cyanide solution is maintained at a higher than ambient constant temperature.

Laser range-gated underwater imaging technology, by removing most of the back scattering noise, can effectively increase the image contrast and extend the detection range. The optical signal captured by a range-gated imaging system primarily comprises reflected light from the object and backscattered light from the surrounding water. Consequently, surfaces with low reflectivity or highly turbid water environments substantially constrain the applicability of the range-gated imaging system. To enhance the detection capability of underwater laser range-gated imaging, this paper proposes the incorporation of underwater polarized light imaging technology as an enhancement method. Based on polarization differences, backscattered light and reflected light from an object can be distinguished. Experimental results indicate that, compared to images obtained using a conventional range-gated laser imaging system, those captured with a polarization-enhanced system exhibit an increase of up to 47%. The proposed approach, which integrates polarization imaging with range-gated laser imaging, has the potential to broaden the applicability of underwater laser imaging scenarios.

The vast array of interconnected microbes across earth’s ecosystems and within holobionts has been called the “Internet of Microbes.” Research into the fundamental microbial properties has demonstrated that bacteria and archaea are masters of energy and information collection, storage, transformation, and dissemination using both “wired” and wireless (at a distance) capacities. These features suggest that microbes are quantum entangled within and between earth’s holobionts, and that specific tools affecting energy and information functions could provide an effective strategy for managing microbial populations. Microbes use four critically important microbial networking functions (sound, light, electricity, and magnetism). This narrative review focuses on microbial management based on two of the four: sound and light (as well as related vibrations). These are examined as: 1) tools for managing microbial populations, 2) tools to support new technologies, and 3) tools for healing humans and other holobionts. Given microbial sensitivity to sound, light, and vibrations, it is critical that microbial populations and microbe-laden holobionts are protected from potentially damaging exposures. We conclude that sound, light, and vibrations are useful therapeutic tools that can help support useful microbial populations and help to address ongoing challenges of holobiont disease.

A novel five-surface phosphor-in-ceramic (FS-PiC) for high illumination and excellent color uniformity in larger-scale LEDs for sensor light source application is demonstrated. YAG phosphor (Y3Al5O12:Ce3+) was uniformly mixed with ceramic and sintered at 680°C to form a phosphor wafer. A sophisticated laser engraving was employed on the phosphor wafer to form a saddle-shaped large-scale FS-PiC LEDs. The performance of the FS-PiC LEDs exhibited the illumination of 401lm, average color temperature (CCT) of 5488K±110K, and color coordinates (CIE) of (0.3179±0.003, 0.3352±0.003). In contrast to convention single-surface phosphor-in-ceramic (SS-PiC) LEDs, the performance exhibited the illumination of 380lm, average CCT of 5830K±758K, and CIE of (0.3083±0.07, 0.3172±0.07). These indicated that the performance of the FS-PiC LEDs was higher than the SS-PiC LEDs for illumination, CCT, and CIE of 1.1, 7, and 23 times, respectively. Furthermore, the FS-PiC LEDs demonstrate lower lumen loss of 2% and less chromaticity shift of 5.4x10-3 under accelerated aging at 350°C for 1008 hours, owing to the high ceramic melting temperature of up to 510°C. In this study, the proposed FS-PiC larger-scale LEDs having excellent optical performance and high reliability may be the promising candidates to replace the convention phosphor-in-organic silicone material used in high-power LEDs for the next generation of sensor light sources, display, and headlight applications.

The development and use of selenium and iodine elements in agriculture aim to enrich agricultural food products for humans. This study was carried out as a three-factor factorial experiment in a completely randomized design (CRD). Three concentrations of sodium selenate fertilizer (0, 2, 4 mg/l), three potassium iodate (0, 2, 4 mg/l), and two supplementary radiation levels (blue light and sunlight) were used. The results showed that the highest and the lowest (3.44 & 3.12 mg/g f.w) leaf protein value was related to blue light and sunlight treatments, respectively. In the blue light treatment, the maximum and the minimum (4.77 & 3.39 mg/g f.w) leaf sugar amount was observed at 4 and 0 mg/l of the iodine, respectively. At 0 mg/l of selenium, the highest and the lowest (8.63 & 5.34 mg/g f.w) leaf vitamin C amount was recorded at the 4 and 0 mg/l of iodine, respectively. In blue light + 0 mg/l of the selenium, the highest and the lowest (2.94 & 2.10 mg/g f.w) leaf flavonoid quantity was seen at 2 and 0 mg/l of the iodine, respectively. In the blue light conditions, (5.20%) leaf nitrogen content was achieved in the selenium 4 mg/l group. In the same conditions, the maximum and the minimum (3.09 & 2.18%) leaf potassium amount was attained at selenium 2 and 4 mg/l, respectively. Under blue light conditions, the highest and the lowest (0.58 & 0.24 mg/kg dry matter) leaf selenium level was observed at 4 and 0 mg/l, respectively. In sunlightradiation levels, the maximum and the minimum (0.36 & 0.25 mg/kg dry matter) leaf selenium level were found at 4 and 0 mg/l of selenium, respectively. In the blue light conditions, the most and the lowest (1.65 & 0.72 mg/kg dry matter) seed selenium content was related to 4 and 0 mg/l of the selenium, respectively. In the blue light conditions, the highest and the lowest (8.49 & 4.25 mg/kg dry matter) leaf iodine level was recorded at 4 and 0 mg/l of iodine, respectively. In the blue light conditions, the maximum and the minimum (30.56 & 20.62 mg/kg dry matter) seed iodine value was related to 4 and 0 mg/l of the iodine, respectively. In the sunlight, the most and the lowest (24.96 & 20.29 mg/kg dry matter) seed iodine amount was achieved at 4 and 0 mg/l of the selenium, respectively.

Response of tomato and eggplant to continuous lighting (CL) and abnormal light/dark (L/D) cycles was studied to elucidate the role of the absence of the dark period in the diurnal cycle in the development of leaf injuries under CL. Four light treatments were set: 16/8 h (control), 24/0 h (CL), 6/6 h, and 24/24 h (abnormal L/D cycles). These light treatments provided average daily light integrals of 17.3, 25.9, 13.0 and 13.0 mol m-2 day-1, respectively. Results of this work have shown that in both tomato and eggplant abnormal L/D cycles caused photoinhibition and leaf injuries similar to those in CL-grown plants. Induced defense mechanisms were not strong enough to contend against oxidative stress caused by light treatments that provided plants with even smaller DLI than 16/8 h photoperiod did. Half time during abnormal L/D cycles were dark periods. Despite these facts, abnormal L/D cycles were injurious. It is concluded that photooxidative stress induced by CL can not be attributed to excessive DLI or the continuity of light itself (the absence of dark periods). Therefore, we believe that the hypothesis suggesting circadian asynchrony to be the main triggering factor of CL-induced leaf injuries is the most plausible among many others proposed.

G4v is a four-vector theory of gravitation proposed by Mead (2015, 2023a,b) which reinterprets several major results commonly celebrated for the tensor-based approach of General Relativity (GR). Here, we show that G4v obeys the correspondence principle, an important test of any relativistic theory. We derive the non-relativistic Lagrangian and Energy expressions at the limit of low speeds and potentials, complete with the correct terms for potential energy (something traditional Special Relativity is incapable of achieving). G4v could represent a new interpretation of the gravitational field with essentially the same mathematics as electromagnetism (Mead 2023a). It is also possible to interpret G4v as a very interesting (and useful) approximation of the Einstein field equations (Mead 2023b).

Due to the ongoing climate change plants face multiple stress factors (mainly the abiotic ones) simultaneously, which means that the reduced yields of critical crops (including wheat, rice, or barley) can be expected. Therefore, our understanding of the light and temperature sensing mechanisms and related signaling is of primary importance. Herein we present a review focused on the direct sensing (ensured via photoreceptors) of light, which is the main abiotic factor driving the development, phenology, and especially resistance against oxidative stress via the increased accumulation of protective metabolites of crops. Thus, in the following text, special attention is paid to the description of the plant photoreceptors, their mode of action, ranges of perception, and related signaling pathways leading to the activation of target transcription factors. These finally lead to alterations in the expression of target genes related to photoprotection. Due to the focus of our research, genes related to the production of phenolic compounds (PheCs) were selected as a representative group of target genes having a UV-screening, and antioxidative function meaning that their activation and activity of resulting proteins can significantly contribute to the increased tolerance of plants against stress cues.

The relativistic effects of the dynamical properties of light at angular incidence were analyzed from the perspectives of Bohr indeterminacy and Heisenberg uncertainties and statistical dispersion. It was found that these effects report minimal uncertainties that agree with one or the other according to the angular range of incidence and that decrease with increasing refringence of the medium, constituting a specific relativistic uncertainty at angular incidence. An anomaly is indicated for the uncertainty principle in the Quantum Theory (QT) setting for small angles of incidence, where the accuracy of the angular position does not imply an increase in the uncertainty of the linear momentum. The anomalies arise because TQ does not predict the alternation between the classical and relativistic regimes of photon inertia at angular incidence. Specific relativistic uncertainty particularizes the uncertainty principle in the transmission of light between media pairs at angular incidence for the relativistic scenario, considering an observer that registers the relativistic effects of measurements that interfere with the observed system, in another inertial referential.

Aim: The purpose of this study is to evaluate the remineralization potential of primary teeth enamel after being exposed to different laser diode therapy. Methods: Ninety-six vestibular primary teeth enamel samples were divided into eight groups (n=12) with varying treatments: control (G1), CPP-ACP-fluoride varnish (G2), diode lasers at 980 nm (G3), 808 nm (G4), 450 nm (G5), 980 nm + CPP-ACP-fluoride varnish (G6), 808 nm + CPP-ACP-fluoride varnish (G7), and 450 nm + CPP-ACP-fluoride varnish (G8). Each sample was assessed using DIAGNOdent® at baseline, post-treatment, and post-pH cycle re-mineralization. SEM imaging was performed before and after treatment and following the pH cycle. Results: The results indicated that the 980 nm and 808 nm diode lasers, both alone and in combination with CPP-ACP-fluoride varnish, either maintained or increased the calcium (Ca) weight percentage (Wt%) in the enamel. The 980 nm diode laser combined with CPP-ACP-fluoride varnish (G6) showed a significant increase in Ca Wt%, suggesting a strong remineralization effect. Similarly, the 808 nm diode laser alone (G4) also promoted a substantial increase in Ca Wt%. In contrast, the 450 nm diode laser, whether applied alone or in combination with CPP-ACP-fluoride varnish, resulted in a lower Ca Wt% and an increase in phosphorus (P) Wt%. Most groups, except for the CPP-ACP-fluoride varnish alone (G2), demonstrated an increase in P Wt%, indicating a complex interaction between laser therapy and enamel remineralization. Conclusions: The combined use of laser therapy with CPP-ACP-fluoride varnish significantly enhanced the remineralization of temporary teeth enamel. The 980 nm diode laser + CPP-ACP-fluoride varnish showed the most pronounced improvement in remineralization, while the 808 nm diode laser alone also effectively increased calcium solubility. These findings suggest that higher wavelength diode lasers, particularly when combined with remineralizing agents, can effectively enhance the mineral content of primary teeth and promote enamel remineralization.

Cacao is an understory plant cultivated under full-sun monocultures to multi-strata agroforestry systems, where cocoa trees are planted together with fruit, timber, firewood, and leguminous trees, or grown within thinned native forests. Under agroforestry systems of cultivation, cacao is subjected to excess shade due to high density of shade trees, and overgrown or unmanaged pruning of shade trees. Cacao is tolerant to shade, and the maximum photosynthetic rate occurs around irradiance of 400 μmol m⁻² s⁻¹ but excess shade reduces the irradiance further which is detrimental to photosynthesis and growth functions. Intra-specific variation is known to exist in cacao for the required saturation irradiance. A greenhouse study was implemented with 58 cacao genotypes selected from four geographically diverse groups: (i) wild cacao from river basins of the Peruvian Amazon, (PWC), (ii) Peruvian farmers’ collection (PFC), (iii) Brazilian cacao collection (BCC) and (iv) national and international cacao collections (NIC). All the cacao genotypes were subjected to 50% and 80% shade where photosynthetic photon flux density (PPFD) was 1000 and 400 μmol m^-2 ּs^-1 respectively. Intra-specific variations were observed for growth, physiological and nutritional traits, and tolerance to shade. Cacao genotypes tolerant to shade were: UNG-77 and UGU-130 from PWC; ICT-2173, ICT-2142, ICT-2172, ICT-1506, ICT-1087, and ICT-2171 from the PFC; PH-21, CA-14, PH-990 and PH-144 from BCC; and ICS-1, ICS-39, UF-613 and POUND-12 from NIC. Genotypes that tolerate excess shade might be useful plant types to maintain productivity and sustainability in agroforestry systems of cacao management.

Indoor farming systems enable plant production in precisely controlled environments, managing factors such as lighting, photoperiod, and nutrient supply, to enhance crop yield and quality. However, the implementation of stable growth conditions and the absence of stress stimulants can weaken plants' defense responses and limit the accumulation of bioactive, health beneficial phytochemicals. A potential solution is the controlled application of stressors, such as supplemental ultraviolet (UV) light, which stimulates secondary metabolites (SM) synthesis and increase overall antioxidant potential. To this end, we analyzed the efficiency of short-term pre-harvest supplementation of red-green-blue (RGB, LED) spectrum with ultraviolet B (UV-B, 311 nm) or C (UV-C, 254 nm) light to boost phytochemicals synthesis. Additionally, given the biological harm of UV radiation due to high-energy photons, we monitored plants’ photosynthetic activity during treatment. Our analyses showed that UV-B radiation, applied with a cumulative dose of 15.622 kJ m–2, did not negatively impact photosynthetic activity while significantly increasing the overall antioxidant potential of lettuce through enhanced levels of polyphenolic SM (total phenolics, flavonoids, anthocyanins) and ascorbic acid. Conversely, UV-C radiation, applied with a lower cumulative dose of 6.008 kJ m–2, induced anthocyanin accumulation in the green leaf cultivar but significantly harmed the photosynthetic apparatus and limited plant growth. These results are crucial for understanding the potential of UV light supplementation in producing functional plants.

The Munich ChronoType Questionnaire (MCTQ) has now been available for more than 15 years; its original publication has been cited 1,240 times (Google Scholar, May 2019); its online version, which was available until July 2017, has produced almost 300,000 entries from all over the world (MCTQ database). The MCTQ has gone through several versions, has been translated into 13 languages and has been validated against other more objective measures of daily timing in several independent studies. Besides being used as a method to correlate circadian features of human biology with other factors – ranging from health issues to geographical factors – the MCTQ gave rise to quantifying old wisdoms, like “teenagers are late” and has produced new concepts, like social jetlag. Some like the MCTQ’s simplicity and some view it critically; it is time to have a self-critical view on the MCTQ, to address some misunderstandings and give some definitions about MCTQ-derived chronotype and the concept of social jetlag.

In this paper, we examine a modified Friedmann model designed to explain cosmic structures and late-time accelerated expansion of the universe, grounded in the spatial distribution of luminous matter. Through comprehensive simulations of our universe, we observe a notable surge in the formation rate of galaxies at redshift z≈1, characterized by a peak expansion rate in cosmic structures formed at z ≈0.9, reaching its zenith at z ≈2. Subsequently, a transition occurs before the onset of dark matter-induced accelerated expansion. The acceleration of the universe stands as an entrenched and virtually model-independent theoretical tenet, resilient to the ongoing debate surrounding the enigma of dark energy. A distinctive redshift transition zone marks the shift from cosmic deceleration to accelerated expansion. The transition is proportional to matter density and contingent upon the geometry of the universe. The influence of the cosmological constant on the evolution of cosmic structures in the CDM paradigm appears insufficient in curtailing the efficiency of late-time structure formation compared to the observed values in the modified model