This paper introduces a new adaptation of the enthalpic lattice Boltzmann method (LBM) tailored to simulate the intricate dynamics of conjugate heat transfer in non-homogeneous media, showcasing considerable potential for enhancing heat exchanger designs. This approach expands upon the conventional enthalpic LBM framework by seamlessly incorporating tailored source terms, enabling precise representation of local and transient variations in the medium’s thermophysical properties. The resulting LBM model comprehensively captures the energy conservation equation, with exceptions made only for flow compressibility and viscous dissipation, thereby significantly augmenting its versatility in analyzing heat exchanger configurations. Verification tests, comprising assessments of both transient and steady-state solutions, unequivocally validate the accuracy of the proposed model, further bolstering its reliability for analyzing heat exchange processes within intricate heat exchanger geometries. To demonstrate its efficacy, simulations of conjugate heat transfer processes involving fluid natural convection within structured cavities were performed, imposing both Dirichlet and Neumann boundary conditions to emulate scenarios encountered in practical heat exchanger operations. The findings yield compelling insights, particularly in the transient regime, revealing the beneficial impact of structured cavities on enhancing heat transfer processes. These insights inform potential design optimizations for heat exchangers. The results emphasize the potential of the modified enthalpic LBM approach to elucidate complex heat transfer phenomena in non-homogeneous media and structured geometries, offering valuable implications for heat exchanger engineering and optimization.

When considering implementation of shallow geothermal energy as a renewable source for heating and cooling of the building, special care should be taken in hydraulic design of borehole heat exchanger system. Laminar flow can occur in pipes due to usage of glycol mixture at low temperature or inadequate flow rate. This can lead to lower heat extraction and rejection rates of the exchanger because of higher thermal resistances. Furthermore, by increasing flow rate to achieve turbulent flow and satisfactory heat transfer rate can lead to increase the pressure drop of the system and oversizing of circulation pump which leads to impairment of seasonal coefficient of performance at the heat pump. Most frequently used borehole heat exchanger system in Europe is double-loop pipe system with smooth inner wall. Lately, development is focused on implementation of different configuration as well as with ribbed inner wall which ensures turbulent flow in the system, even at lower flow rates. At a location in Zagreb, classical and extended thermal response test was conducted on three different heat exchanger configurations in the same geological environment. With classic TRT test, thermogeological properties of the ground and thermal resistance of the borehole were determined for each smooth or turbulator pipe configuration. Extended Steady-State Thermal Response Step Test (TRST) was implemented, which incorporate series of power steps to determine borehole extraction rate at the define steady-state heat transfer conditions of 0/-3°C. Results show that heat exchangers with ribbed inner pipe wall have advantages over classic double-loop smooth pipe design, in terms of greater steady state heat extraction rate and more favorable hydraulic conditions.

In this paper, comprehensive analysis of combined effect of major influencing parameters on heat transfer in the single U-tube BHE (sBHE) and double U-tube BHE (dBHE) with two independent circuits was performed by using validated numerical heat transfer model. Geometrical parameters, such as shank spacing (with maximum, average and minimum values) and borehole diameter (large, medium and small borehole sizes) and borehole depth (shallow, average and deep borehole depths) as well as thermal conductivity of soil and grout which ranges from minimum to high value were considered. The combined impact of these parameters was included under four major cases: 1) combined effect of borehole depth, borehole size and shank spacing; 2) combined effect of borehole depth, and soil and grout thermal conductivity; 3) combined effect of soil and grout thermal conductivity and borehole size; and 4) combined effect of soil thermal conductivity, borehole size and shank spacing. Each of these major cases has nine different design options of both sBHE and dBHE. Series of results of heat transfer per unit borehole depth were generated for all the considered various cases. With the given parameters, the BHE case that provides highest heat transfer among the various cases of sBHE and dBHE were obtained.

As the demand of heating and air conditioning is increasing day by day due to getting a comfortable life, for that reason, the market for heat pump and air conditioning systems or both, is seeing a steady increase in low global warming potential. All researchers on heat pump and air conditioning systems are searching for environmentally friendly refrigerants. However, a significant number of contemporary refrigerants (HCFCs) have the potential to cause global warming and ozone depletion, such as those found in heat pump air conditioning systems. Using more environmentally friendly refrigerants, including hydrocarbon and blend refrigerant mixtures, is one way to lower GWP and Ozone depletion potential. This study examines the performance of several alternative refrigerants, including R32, R134A, R410A, R22, and R290. In order to examine the performance of R290, theoretical and simulation results are compared on various refrigerants while taking into account a number of performance parameters, including the refrigerant energy efficiency ratio, mass flow rate, coefficient of performance, cooling capacity, and compressor work for one ton of refrigeration (1TR) air conditioners. One player with a very low GWP is R290. However, the only drawback is that it can catch fire and is hazardous to use in split-type commercial heat pump air conditioning applications. The environmental and thermo physical properties of HC-290 are significantly better than those of other materials, according to theoretical and simulation studies utilizing Cool Pack software, hence it is a viable replacement.

Building roofs are sources of unwanted heat for buildings situated in zones with a warm climate. Thus, reflective coatings have emerged as an alternative to reject a significant fraction of solar energy received by roofs. In this research, the thermal behavior of concrete slab-type roofs with traditional and solar reflective coatings was simulated using a computational tool. Weather data from four cities in Mexico with a warm climate were used as boundary conditions. This tool is an in-house code based on the Finite Volume Method developed by the author to perform building components simulations. The code was validated with experimental data from previous work. A series of comparative simulations were developed, taking a gray roof as a control case. The results showed that for the roof without thermal insulation (single roof), the solar reflective coatings reduced the exterior surface between 11 and 16∘C. Consequently, the single roofs’ daily heat gain was reduced by a factor ranging between 41 and 54%. On the other hand, for the insulated roof, the reflective coatings reduced the exterior surface temperature between 17 and 21∘C. At the same time, the daily heat gain of composite roofs was reduced between 37 and 56%.

The aim of this paper is to expose the main involved physical phenomena underlying the alteration of convective heat transfer in a heat exchanger subjected to imposed vibrations. This technique seems to have interesting features and industrial applications, such as efficiency increase, heat transfer rate control and cleanliness action. However, a clear description and comprehension of how vibrations may alter the convective heat transfer coefficient in a heat exchanger is no still reached due to the complexity of the involved physical mechanisms. For this reason, after a presentation and a schematisation of the analyzed thermodynamic system, the fundamental alterations of the thermo-fluid dynamics fields are described. Then, the main involved physical phenomena are exposed for the three cases of gaseous, monophasic liquid and boiling liquid mediums. Finally, on the basis of the characteristics of these described phenomena, some considerations and indications of general validity are presented.

Medium-deep Borehole Heat exchanger (MBHE) has been widely paid attention for building heating. In order to avoid the thermal interference of adjacent MBHEs, temperature distribution characteristics of medium-deep rock-soil was investigated in this work. The evolution on maximum rock-soil thermal affected radius (MTAR) in full life cycle was further analyzed. The results showed that the rock-soil thermal affected area (RTAA) continuously expands in both radial and vertical directions during a heating season. Several factors of thermal extraction load, fluid velocity, geothermal gradient and pipe length have main impacts on the RTAA in vertical direction. Rock-soil thermal conductivity affects the RTAA in both radial and vertical directions. In non-heating season, temperature difference of rock-soil in radial direction dominates the temperature recovery in the first year while geothermal flow nearly dominates temperature recovery after 20 years. The thermal affected radius (TAR) in the 30 th year could be determined as an effective MTAR in full life cycle. In order to decrease installed distance of adjacent MBHEs, a new well layout form by deflecting borehole was proposed. The recommended deflection angle is equal to or larger than 4 times TAR angle. This work provides scientific reference for promoting application of multiple MBHE arrays.

A sintered wick was formed in a heat pipe through the process of sintering a mixture of copper powder with particle sizes of 100㎛ and 200㎛, mixed with a pore-forming agent. On application to the heat pipes. The thermal resistance of heat pipes containing a sintered wick was calculated for different tilting angles (0°, 45°, and 90°) according to the type of powder, thickness of the sintered wick, and the filling ratio of the working fluid. The heat transfer efficiencies were evaluated through temperature tests. The capillary force, which is closely related to heat transfer efficiency, is determined by the effective pore radius resulting from the sintering of the copper powder. Furthermore, it was observed that the heat transfer performance of the heat pipe was at its best when the working fluid filling ratio was 30%. Additionally, the width of the wick was found to have a direct correlation with the heat transfer performance.

The objective of this work is to analyze the improvement of heat transfer in trapezoidal fin heat exchangers using numerical simulation. Heat exchangers are essential components frequently used in contemporary electronic gadgets to effectively disperse heat produced by high-power components. Nevertheless, as electronic devices continue to advance and become more powerful, the heat transfer capacity of heat exchangers is facing more requirements, therefore requiring enhanced heat dissipation efficiency. Afterwards, various fin angles were adjusted, and the heat transmission efficiency was compared. Modifying the angles can significantly improve the effi-ciency of convective heat dissipation. Moreover, it has been found that employing an optimized trapezoidal fin structure can further enhance the efficiency of heat transfer. The results indicate that trapezoidal fin heat exchangers provide superior heat dissipation efficiency compared to conventional heat exchangers. This is important for enhancing the thermal dissipation capabili-ties of electrical gadgets, hence guaranteeing steady functionality and extending their longevity. Subsequent study might explore supplementary methods to boost heat transmission in different heat exchanger configurations in order to meet the growing requirements for heat dissipation.

In this research, a novel method to investigation the transient heat transfer coefficient in a channel is suggested experimentally, in which the water flow, itself, is considered both just liquid phase and liquid-vapor phase. The experiments were designed to predict the temporal and spatial resolution of Nusselt number. The inverse technique method is non-intrusive, in which time history of temperature is measured, using some thermocouples within the wall to provide input data for the inverse algorithm. The conjugate gradient method is used mostly as an inverse method. The temporal and spatial changes of heat flux, Nusselt number, vapor quality, convection number, and boiling number have all been estimated, showing that the estimated local Nusselt numbers of flow for without and with phase change are close to those predicted from the correlations of Churchill and Ozoe (1973) and Kandlikar (1990), respectively. This study suggests that the extended inverse technique can be successfully utilized to calculate the local time-dependent heat transfer coefficient of boiling flow.

Demand for development of the convergence industry, research studies on electrical conductivity, thermal characteristics, semiconductors, motors, and batteries using special materials have come to the fore. Meanwhile, molybdenum (Mo) exhibits relatively small inorganic qualities, and the thermal conductivity rate is applied to various fields. In this study, in-depth characteristics were considered regarding the concentration of thermal characteristics, IR car terminal characteristics, and IR ve-hicles. This study calculated each phase temperature of the molybdenum sputtered specimens in the steady state according to the heat transfer theory. When the molybdenum-sputtered fabric’s metal layer pointed to the outside air, the heat transfer rate (Q) was high at 5748.3W, In contrast, if the molybdenum sputtered film’s metal layer of the pointed toward the heat source, the heat transfer rate (Q) was low at 187.1W. As a result of measuring the IR transmittance, the infrared transmit-tance of the molybdenum sputtering-treated sample was significantly reduced compared to the untreated sample. In the case of untreated samples, the transmittance ranged from 92.7 to 42.0%. When only the cross part was treated with molybdenum sputtering and the molybdenum surface was directed toward the IR irradiator, the IR transmittance was 66.8~0.7%. It is believed that the molybdenum sputtering polyamide samples produced in this study can be applied to multifunc-tional military wear, biosignal detection sensors, semiconductor products, batteries, etc., by utilizing excellent electrical properties, stealth functions, IR blocking properties, and lightness for infrared thermal imaging detectors.

This study mainly experimentally investigates and explores the effects of local low-frequency vibrations on the starting-up and heat transfer characteristics of the pulsating heat pipe. A micro motors with the vibration frequency of 200 Hz were imposed on the external surface of evaporation, condensation and adiabatic section of the pulsating heat pipe, respectively, and the starting-up temperature and the average temperatures along the evaporation section as well as the thermal performances of the vibrating heat pipe were experimentally scrutinized under the local vibrations of different positions. The following important conclusions can be achieved by the experimental study: 1) The effect of vibrations at the evaporation section and at the adiabatic section on the starting-up time of pulsating heat pipe is more significant than that at the condensation section. 2) The vibrations at different positions can reduce the starting-up temperature of the pulsating heat pipe. The effect of the vibrations at the evaporation section is the best as the heating power is lower, and the effect of the vibration at the adiabatic section is the best as the heating power is higher. 3) The vibrations at the evaporation section and at the adiabatic section can reduce the thermal resistance of the pulsating heat pipe. However, the vibrations at the condensation section have little effect on the thermal resistance of the pulsating heat pipe. 4) The vibrations at the evaporation section and at the adiabatic section can effectively reduce the temperature of evaporation section of the pulsating heat pipe, but the vibrations at the condensation section have no effect on the temperature of evaporation section of the pulsating heat pipe.

Introduction: Heat is a kinetic process whereby energy flows from between two systems; hot-to-cold objects. In oro-dental implantology, conductive heat transfer/(or thermal stress) is a complex physical phenomenon to analyze and consider in treatment planning. Hence, ample research has attempted to measure heat-production to avoid over-heating during bone-cutting and -drilling for titanium (Ti) implant-site preparation and insertion, thereby preventing/minimizing early (as well as delayed) implant-related complications and failure. Objective: Given the low bone-thermal conductivity whereby heat generated by osteotomies is not effectively dissipated and tends to remain within the surrounding tissue (peri-implant), increasing the possibility of thermal-injury; this work attempts to obtain an exact analytical solution of the heat equation under exponential thermal-stress, modeling transient heat transfer and temperature changes in Ti implants upon hot-liquid intake. Materials and Methods: We investigate the impact of the material, the location point along implant length, and the exposure time of the thermal load on temperature changes. Results: Despite its simplicity, the presented solution contains all the physics and reproduces the key features obtained in previous numerical analyses studies. To the best of knowledge, this is the first introduction of the intrinsic time, a “proper” time that characterizes the geometry of the dental implant, where we show, mathematically and graphically, how the interplay between “proper” time and exposure time influences temperature changes in Ti implants, under the suitable initial and boundary conditions. Conclusions: This work aspires to accurately complement the overall clinical diagnostic and treatment plan for enhanced bone-implant interface, implant stability and success rates, whether for immediate or delayed loading strategies.

This paper presents a comparative study of heat transfer performance of lattice structured heat sinks. 20 different unit cells were chosen and heat sinks were modelled in nTop with constant unit cell size. Al 6061 alloy was chosen for analysis due to its good thermal conductivity, low weight, low cost, and high strength. Steady state thermal analysis was performed using ANSYS with constant input parameters for all samples. Heat flux and temperature distribution within the heat sinks were analysed. The study aims to provide a comprehensive understanding of the thermal performance of lattice heat sink designs.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

This paper predict and effectively control the temperature distribution of the steady-state and transient states of anisotropic four-layer composite materials online, knowing the density, specific heat, heat conductivity and thickness of the composite materials. Based on the transfer function, a mathematical model was established to study the dynamic characteristics of heat transfer of the composite materials. First of all, the Fourier heat transfer law was used to establish a one-dimensional Fourier heat conduction differential equation for each composite layer, and the Laplace transformation was carried out to obtain the system function. Then the approximate second-order transfer function of the system was obtained by Taylor expansion, and the Laplace inverse transformation was carried out to obtain the transfer function of the whole system in the time domain. Finally, the accuracy of the simplified analytical solutions of the first, second and third order approximate transfer functions was compared with computer simulation. The results showed that the second order approximate transfer functions can describe the dynamic process of heat transfer better than others. The research on the dynamic characteristics of heat transfer in the composite layer and the dynamic model of heat transfer in composite layer proposed in this paper have a reference value for practical engineering application. It can effectively predict the temperature distribution of composite layer material and reduce the cost of experimental measurement of heat transfer performance of materials.

The plate fin heat exchanger is the compact heat exchanger applied in many industries because of its high thermal performance. To enhance the heat transfer of plate fin heat exchanger in further, three new kinds of wavy plate fins, namely perforated wavy fin, staggered wavy fin and discontinuous wavy fin are proposed and investigated by CFD simulations. The effects of key design parameters, including that of waviness aspect ratios, perforation diameters, stagger ratios and breaking distance are investigated, respectively, with the Reynolds number changes from 500 to 4500. It is found that due to the swirl flow and efficient mixing of fluid, the perforation, serration and breaking techniques are beneficial for the enhancement of heat transfer compared to the traditional wavy fin. At the same time, serration is beneficial to reduce the friction factor, and the breaking technique can reduce heat transfer area as well as enhance heat transfer performance. Through the performance evaluation criteria, the staggered wavy fin has an advantage over the small waviness aspect ratio compared to the perforated wavy fin. The maximum performance evaluation criteria (PEC), as high as 1.24, can be obtained for the perforated wavy fin at the largest waviness aspect ratio.

In this work, we experimentally investigate mass and heat transport phenomena in a modular device while converting a solution salinity difference into a temperature difference. Operations occur under fixed total ambient pressure and without mechanical moving parts, thus realizing a fully static conversion. Provided that a constant salinity gradient can be imposed, the proposed device is able to generate a steady cooling capacity. Here, we purposely operate with environmentally benign and easily accessible sodium chloride water solutions only. A numerical model is finally elaborated, validated and used to explore a wider range of possible device configurations and operating conditions.

Higher order femtoscopy measured to examine the heat exchanger characterization of the fluid debris produced in the collisions and investigated a remarkable suppression in the bosons interferences measurement. The analogous suppression can be analyzed to explore the coherence of boson thermal particle production sources at unprecedented energies. We illustrate the particles emissions from radiated sources with statistical coherence which induce the thermal particles interferences to probe the peculiarity of the heated sources as well as the distinctions about the heat exchangers in the collisions at higher temperature. We perspicacious that the bosons seem to the pertinent aspirant of heat exchanger, and the normalized three particles correlators evaluate the existence of such hybrid phases significantly. The key point of this research is that we analyze the three particles correlations with their normalized correlations by difference equations to determine the characteristics of heat exchanger and its applications. With such distinctive and efficient approach, we observe a significant difference in the correlation functions at higher temperature and momenta regimes.

The heritage of ancient buildings is an important part of the world's history and culture, which has an extremely rich historical-cultural value and artistic research value. Beijing has a large number of palace ancient buildings, and because of the age of their construction, many of them have problems of varying degrees of peeling and mold on the inner surfaces of the envelope. To solve the problems of the damp and moldy interior of palace buildings, a mathematical model of indoor heat and moisture transfer was established based on a wooden palace ancient building in Beijing. Through the indoor mold distribution validation model, the effects of outdoor humidity, soil moisture, wall humidity, and other factors on the indoor heat and moisture transfer of ancient buildings were simulated and analyzed by using the control variables method. The results showed that the molds were distributed at the indoor corners and floors, and the simulation of indoor humidity match the measured humidity. Thus, the simulation results were consistent with the actual situation. The variable trend of the relative humidity of the indoor environment with the outdoor humidity is inconsistent from plane to plane, i.e. it increases or remains constant with the increase of the outdoor humidity. The indoor ambient relative humidity increased with increasing the wall humidity. And the indoor average temperature is 23.3 ℃ and indoor relative humidity ranged between 90.9 % to 92.44 %. Soil moisture and wall humidity were the main factors affecting the indoor environmental relative humidity.

Heat exchangers play a vital role in numerous sectors like power generation and automotive manufacturing. Enhancing the energy efficiency of these exchangers stands as a significant hurdle. Utilizing nanofluids emerges as an optimal solution to augment heat transfer rates, leveraging their superior thermal conductivity while addressing economic constraints linked with traditional heat exchanger technologies. The motivation for this study is to consider the comprehensive synergistic features of MWCNTs, SiO₂, and hybrid MWCNTs–SiO₂ EG-based nanofluids in plate heat exchangers. This was achieved by simulating a plate heat exchanger using CFD (Fluent and Gambit softwares) considering the comparison of two SiO₂, MWCNTs, and their hybrid forms at different mass concentrations. The Reynolds-Averaged Navier-Stokes (RANS) method was employed to model turbulent flows, and the nanoparticles were compared in both single-phase and two-phase states, with their properties derived from experimental studies. Moreover, Nusselt number, convective heat transfer coefficient, and pressure drop variations were computed at different Reynolds numbers. The findings indicated an increase in the Nusselt number with the incorporation of the hybrid nanofluid, achieving a maximum enhancement of 11.19% in comparison to EG at a Reynolds number of 240 and a concentration of 0.86 wt.%. Noticeably, the pressure drop remained negligible at lower Reynolds numbers, exhibiting marginal variations up to 0.3% at higher Reynolds numbers. At a concentration of 0.86 wt.% and a Reynolds number of 480, the introduction of MWCNTs, hybrid, and SiO₂ nano-additives resulted in respective increases in the heat transfer coefficient by 21.02%, 10.76%, and 2.16% and corresponding alterations in pressure drop of 0.11%, 0.04%, and 0.02%.

In the paper the new, fractional order, state space model of a heat transfer in a one- 1 dimensional metallic rod is addressed. The fractional orders of derivative along space and time 2 are not exactly known and they are described by intervals. The proposed model is the interval 3 expanding of the state space fractional model of the one dimensional heat transfer. It is expected to 4 better describe the reality because interval order of each real process is hard to estimate. Elementary 5 properties of the proposed model are analysed. Theoretical results are experimentally validated using 6 data from real experimental laboratory system.

Turbine generator operates with complex cooling system due to the challenge in controlling the peak temperature of the stator bar caused by ohm loss, which is unavoidable. Therefore, it is important to characterise and quantifies the thermal performance of the cooling system. The focus of the present research is to investigate the heat transfer and pressure loss characteristics of typical cooling system, so-called stator ventilation duct. A real scale model was built at its operating conditions for the present study. The direction of cooling air is varied to consider its operation condition, so that there are (1) outward flow and (2) inward flow cases. In addition, the effect of (3) cross flow (inward with cross flow case) is also studied. The transient heat transfer method using thermochromic liquid crystals is implemented to measure full surface heat transfer distribution. A series of Computational Fluid Dynamics analysis is also conducted to support the observation from the experiment. For the inward flow case, the results suggest that the average Nusselt number of the 2nd duct is about 30% higher than the 3rd duct. The trend is similar with the effect of cross flow. The CFD results are in good agreement with the experimental data.

This study proposes parabolic dish-based toroidal structured fractal solar collectors. The potential of fractal geometry to increase heat transfer and the ability of the parabolic dish to concentrate solar rays form the basis of the proposed design for increasing the efficiency. In the study, the thermal and hydrodynamic behaviors of the proposed 3-row, 4-row and 5-row parabolic collectors were investigated comprehensively. Using theoretical modeling and experimental results, the performances of the proposed parabolic dish-based toroidal fractal solar collectors were evaluated and compared via numerical simulation methods. After the experimental studies of the 3-row toroidal fractal collector, the analysis studies were completed using the ANSYS-Fluent program. Then, simulations were carried out for other toroidal solar collectors using the results of these experimental studies. As a result of the converging numerical analyzes, the radiative, hydrodynamic and thermal analysis results of the toroidal absorbers in 3-row, 4-row and 5-row structures integrated with the parabolic dish were compared. In the temperature distribution analysis, it was observed that the parabolic dish effectively focuses on the sun rays and provides a gradual temperature increase of approximately 21 K for the fractal collector. It is observed that 96.84% convergence was achieved between the experimental and numerical results.

The future power equipment tends to take hydrogen or middle/low heat-value syngas as fuel for low emission. The heat transfer of film cooled turbine blade shall be influenced more by radiation. Its characteristic of conjugate heat transfer is studied experimentally and numerically in the paper by considering radiation heat transfer, multi-composition gas and TBC. The Weighted Sum of Gray Gases spectral model and Discrete Transfer Model are utilized to solve the radiative heat transfer in the multi-composition field, while validated against the experimental data for the studied cases. It is shown that the plate temperature increases significantly when considering the radiation and the temperature gradient of the film cooled plate becomes larger. It is also shown that increasing percentage of steam in gas composition results in increased temperature on the film-cooled plate. The normalized temperature of the film-cooled plate decreases about 0.02, as the total percentage of steam in hot gas increases per 7%. As for the TBC effect, it can smooth out the the temperature distribution and insulate the heat to a greater extent when the radiative heat transfer becomes significant.

This paper studies the evaporative heat transfer characteristics of R744 at low temperatures in a horizontal smooth tube as a cascade refrigeration system (CRS) among hybrid cascade refrigeration systems (HCRSs). There is a lack of research on the low-temperature evaporative heat transfer characteristics of R744 under the operating conditions of evaporators used in actual CRSs used in supermarkets. Therefore, this study aims to provide basic data on the evaporative heat transfer characteristics of R744 in the evaporators of refrigerators used in supermarkets. The tube used in the evaporation experiment conducted herein was a smooth horizontal copper tube with an inner diameter and length of 11.46 mm and 8000 mm, respectively. The experimental pa-rameters were as follows: heat fluxes of 12–21.5 kW/m2, mass fluxes of 75–225 kg/(m2·s), and saturation temperatures of −50–−30 °C. The main results are summarized as follows. (1) When designing the R744 evaporator, the mass and heat fluxes must be maximized within the operating conditions, and the saturation temperature must be designed to be as low as possible. (2) The evaporative heat transfer coefficient of R744 can be predicted well by using the correlation formula of Chen at the evaporation temperature of −40 °C in the CRS.

To overcome the two-phase flow instability of traditional boiling heat dissipation technologies, a porous wick was used for liquid-vapor isolation, thus realizing efficient and stable boiling heat dissipation. A pump-assisted capillary phase-change loop with methanol as working medium was established to study the effect of liquid-vapor pressure difference and heating power on its start-up and steady-state characteristics. The results indicated that the evaporator undergoes four heat transfer modes including flooded, partial flooded, thin film evaporation and overheating. The thin film evaporation mode was the most efficient one with the shortest start-up period. Besides, the heat transfer modes were determined by liquid-vapor pressure difference and power. The heat transfer coefficient could be significantly improved and the thermal resistance could be reduced by increasing liquid-vapor pressure difference as long as it did not exceed 8 kPa. However, when the liquid-vapor pressure difference exceeded 8kPa, its influence on the heat transfer coefficient weakened. In addition, a two-dimensional heat transfer mode distribution diagram considering both liquid-vapor pressure difference and power was drawn through a great number of experiments. During engineering application, the liquid-vapor pressure difference can be controlled to maintain efficient thin film evaporation in order to achieve the optimum heat dissipation effect.

Chemical vapor deposition (CVD) is a vital process for depositing thin films of various materials with precise control over thickness, composition, and properties. Understanding the heat and mass transfer mechanisms during CVD is essential for optimizing process parameters and ensuring high-quality film deposition. This review provides an overview of recent advancements in the heat and mass transfer modeling for chemical vapor deposition processes. It explores innovative modeling techniques, recent research findings, emerging applications, and challenges in the field. Additionally, it discusses future directions and potential areas for further advancement in CVD modeling.

The study of the influence of the nanoparticle volume fraction and aspect ratio of microchannels on the fluid flow and heat transfer characteristics of nanofluids in microchannels is important in the optimal design of heat dissipation systems with high heat flux. In this work, the computational fluid dynamics method was adopted to simulate the flow and heat transfer characteristics of two types of water–Al2O3 nanofluids with two different volume fractions and five types of microchannel heat sinks with different aspect ratios. Results showed that increasing the nanoparticle volume fraction reduced the average temperature of the liquid–solid heat transfer surface and thereby improved the heat transfer capacity of the nanofluids. Meanwhile, the increase of the nanoparticle volume fraction led to a considerable increase in the pumping power of the system. Changing the aspect ratio of the microchannel effectively improved the heat transfer capacity of the heat sink. Moreover, increasing the aspect ratio effectively reduced the average temperature of the heating surface of the heat sink without significantly increasing the flow resistance loss. When the aspect ratio exceeded 30, the heat transfer coefficient did not increase with the increase of the aspect ratio. The results of this work may offer guiding significance for the optimal design of high heat flux microchannel heat sinks.

The shape memory alloys belong to the smart materials thanks to their thermomechanical proprieties' reply to thermal or to mechanical loading. These materials can change shape, stiffness, displacement, natural frequency, and many mechanical characteristics in response to stress or to heat such as conduction, convection or radiation. However, heating by convection or conduction are the most useful and studied methods unlike radiation. Therefore, this paper aims to study the radiation effect on the shape memory alloy behavior

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

Regeneratively cooled scramjet has already been successfully verified as propulsion device for hypersonic vehicle. As a result, dynamic process of flow and heat transfer in cooling channel is commonly occurred which may bring hazard and control difficulties for scramjet. To study transient flow and heat transfer process in cooling channel, a dynamic numerical model is established. Dynamic characteristics of flow and heat transfer under different conditions are calculated and discussed, which includes change of inlet fuel mass flow, heat flux and pressure working conditions. Results show that stable time of cooling channel outlet fuel temperature is related to the change rate of inlet mass flow and heat flux. The stable time of outlet fuel temperature under heat flux decreasing working conditions are about 12.5 s. The initial response of working pressure fluctuation will lead to fuel temperature fluctuation, which has little effect on wall temperature.

Space shuttle has been a hall mark of American space program since its inception. Despite its temporary shutdown few years ago, with the recent interest in space exploration which includes revitalizing human outpost in microgravity and transportation required to build it, realize other experiments (e.g. in space telescopes, in space manufacturing) and interplanetary voyages, it has regained attention. Its superior design, manufacturing, materials, performance, durability, and efficiency place it among the best, in fact, the only effort by mankind to build a reusable craft horizontally, launch vertically like a rocket and fly back like a plane. Various requirements emerge during its design (thermal, fluid, acoustics, vibration and structural) and design of its main engine (Aerojet Rocketdyne RS 25) which requires considerable attention, heat transfer being most important. This facilitated and necessitated use of various types of heat exchangers such as single coil, heat pipe, built in internal heat exchanger (IHEX), external heat exchanger (EHEX), condensing heat exchanger (CHEX), Interface heat exchangers (InHEX), regenerative heat exchanger (RHEX) and compact heat exchangers (CoHEX), change, manipulate and optimize their configurations in piping and instrumentation diagrams (PIDs). In this short narrative, an effort has been made to summarize them, and their developments over time with a focus on the application, design, manufacturing, materials, and performance (in service and final operation).

The study of turbulent heat transfer in liquid metal flows has gained interest because of applications in several industrial fields. The common assumption of similarity between the dynamical and thermal turbulence, namely the Reynolds analogy, has been proven to be not valid for these fluids. Many methods have been proposed in order to overcome the difficulties encountered in a proper definition of the turbulent heat flux, such as global or local correlations for the turbulent Prandtl number or four parameter turbulence models. In this work we assess a four parameter logarithmic turbulence model for liquid metals based on RANS approach. Several simulation results considering fluids with Pr = 0.01 and Pr = 0.025 are reported in order to show the validity of this approach. The Kays turbulence model is also assessed and compared with integral heat transfer correlations for a wide range of Peclet numbers.

The pulsating flow is one of the techniques which can enhance heat transfer, therefore leading to energy saving in tubular heat exchangers. This paper investigates the heat transfer and flow characteristics in a two-dimensional in-line tube bundle with the pulsating flow by a numerical method using the Ansys Fluent. Numerical simulation is performed for Reynolds number Re = 500 with different frequencies and amplitude of pulsation. Heat transfer enhancement was estimated from the central tube of the tube bundle. Pulsation velocity had an asymmetrical character with a reciprocating flow. The technique developed by the authors to obtain asymmetric pulsations was used. This technique allows simulating an asymmetric flow in heat exchangers equipped with a pulsation generation system. Increase in both the amplitude and the frequency of the pulsations has a significant effect on heat transfer enhancement. Heat transfer enhancement is mainly observed in the front and back of the cylinder. At a steady flow in these areas, heat transfer is minimal due to the weak circulation of the flow. The increase in heat transfer in the front and back of the cylinder is associated with increased velocity and additional flow mixing in these areas.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

This work probes the combined effects of magnetic field and viscous dissipation on heat field and examine the second law analysis (entropy generation) in an electrically conducting fluid under the effect of wall mass transfer over continuous stretched non-isothermal surface with variable viscosity. The viscosity of the fluid is assumed to be an inverse linear function of temperature. The governing equation for the problem are changed to dimensionless ordinary differential equations by using similarity transformation and solved numerically by using Rung Kutta and Shooting technique. Velocity, concentration and temperature distribution are obtained and used to compute the entropy generation and the Bejan number in the flow field. The effect of variable viscosity, Schmidt number, Hartman and Reynolds number on the velocity, concentration, temperature, entropy generation and Bejan number are studied and discussed.

Pool boiling heat transfer is recognized as one of the most effective heat transfer methods and has extensive applications in industry. The application of non-azeotropic binary mixtures can not only meet the environmental requirements of modern industrial development, but also improve the coefficient of performance (COP) of many systems. Therefore, studying the boiling heat transfer characteristics of non-azeotropic mixtures is important on improving their potential industrial application. This article selected ethylene glycol/deionized water (EG/DW) at varies concentration as the research working fluids, and conducted experimental research on the pool boiling performance. At the same time, the thermophysical parameters of the mixtures were studied and analyzed. The results showed that the concentration of EG in the mixture had a significant impact on the thermal properties and temperature glide of the mixture, where both affected the heat transfer deterioration. Based on experimental data, six widely used heat transfer coefficient prediction correlations were used for calculation, and two of them were modified. The deviation between the modified correlations and the experimental results remained within 20%.

New analytical solutions of the heat conduction equation are presented in cylindrical and spherical coordinates. Then these solutions are reproduced with high accuracy by recent explicit and unconditionally stable finite difference methods. After this, real experimental data from the literature regarding a heated cylinder are reproduced by the explicit numerical methods as well as by Finite Element Methods (FEM) ANSYS workbench. Convection and nonlinear radiation are also considered on the boundary of the cylinder, and it is shown that the explicit methods are much more accurate than the commercial software.

Nanofluids are a novel class of heat transfer fluid that plays a vital role in industries. In mathematical investigations, these fluids are modeled in terms of traditional integer-order partial differential equations (PDEs). It is recognized that traditional PDEs cannot decode the complex behavior of physical flow parameters and memory effects. Therefore, this article intends to study the mixed convection heat transfer in nanofluid over an inclined vertical plate via fractional derivatives approach. The problem in hand is modeled in connection with Atangana-Baleanu fractional derivatives without singular and local kernel having strong memory. The human blood is considered as base fluid dispersing carbon nanotube (CNTs) (single-wall carbon nanotubes (SWCNTs) and multi-wall carbon nanotubes(MWCNTs )) into it to form blood-CNTs nanofluid. The nanofluids are considered to flow in a saturated porous medium under the influence of an applied magnetic field. The exact analytical expressions for velocity and temperature profiles are acquired using the Laplace transform technique and plotted in various graphs. The empirical results indicate that the memory effect decreases with increasing fractional parameters in the case of both temperature and velocity profiles. Moreover, the temperature profile is higher for blood-SWCNTs by reason of higher thermal conductivity whereas, this trend is opposite in case of velocity profile due densities difference.

The hygrothermal transfer is very important for the design of a building envelope for thermal comfort and economic and energy analysis of the building envelope. The applications of various materials in building envelope have been studied extensively. The study presents several models for the hygrothermal transfer for various building walls. Several energy and mass conservation equations with different boundary conditions and input considerations were presented in this paper for concrete, bricks and wooden walls. The effect of hysteresis was ignored in developing most model equations, while few considered flow pattern of fluid through the wall surfaces. Due to the flexibility of Luikov models, it formed the basis for modelling the coupled heat and mass transfer for porous material independent of hygroscopic nature with different boundary conditions defined according to the geometry and orientations. The influence of type of wall, orientation, thickness, the density of the material and climatic variations on the temperature and moisture evolutions within the building materials was more pronounced. Literature, presenting imaging models using imagery software like COMSOL multi-physics, CFD etc. were scarce considering that microscopic imagery is now deployed to measure the heat and moisture evolution in materials. Future models should include shrinkage or expansion influence on the fibrous material like wood due to their behaviour under environmental condition.

This investigation aims to discuss the formation process of eddies and the heat transportation in plasma keyhole arc welding. In order to clarify this issue, the measurement of the convection inside the weld pool, the convection on the weld pool surface, also the temperature distribution on the weld pool surface were carried out. The results showed that two eddies were found in the weld pool, which is controlled mainly through the shear force by the plasma flow acting on the weld pool surface. The magnitude, extent and direction of the shear force are thought to be determined primarily by the variation of keyhole profile. The relative shape and strength of each eddy is largely changed depending on the change of the keyhole profile when nozzle diameter changed. These relative strengths of each eddy are considered to decisively govern the heat transport in the weld pool coinciding with the direction of eddies. A larger eddy near the lower part of the keyhole inside the weld pool was found out in the case of 1.6 mm, meanwhile a upward larger eddy was found out near the upper part of the keyhole inside the weld pool in the case of 2.4 mm.

A non-Newtonian fluid model is used to investigate the two-dimensional pulsatile blood flow through a tapered artery with a stenosis. The mixed convection effects of heat and mass transfer are also taken into account. By applying non-dimensionalization and radial coordinate transformation, we simplify the system in a tube. Under the finite difference scheme, numerical solutions are calculated for velocity, temperature concentration, resistance, impedance, wall shear stress and shearing stress at the stenosis throat. Finally, Quantitative analysis is carried out.

This study presents the comparison of heat transfer capacity and pressure drop characteristics between a basic fin-tube heat exchanger and a modified heat exchanger with the structural change of branch tubes and coiled turbulators. All experiments were carried out using an air-enthalpy type calorimeter based on the method described in ASHRAE standards, under heat exchanger experimental conditions. 14 different kinds of heat exchangers were used for the experiment. Cooling and heating capacities of the turbulator heat exchanger were excellent, compared to the basic one. As the insertion ratio of the coiled turbulator and the number of row increased, the heat transfer performance increased. However, the capacity per unit area was more effective in 4 rows than 6 rows, and the cooling performance of the 6 row turbulator heat exchanger (100% turbulator insert ratio) was down to about 6% than that of 4 row one. As the water flow rate and the turbulator insertion ratio increased, the pressure drop of the water side increased. This trend was more pronounced in 6 rows. In the cooling condition, the pressure drop on the air side was slightly increased due to the generation of condensed water, but was insignificant under the heating condition. The power consumption of the pump was more affected by the water flow rate than the coiled turbulator. The equivalent hydraulic diameter of a tube by the turbulator was reduced and then the heat transfer performance was improved. Thus, the tube diameter was smaller, the heat flux was better.

The steady-state, coupled heat and mass transfer from a fluid flow to a sphere accompanied by an exothermal catalytic chemical reaction on the surface of the sphere is analysed taking into consideration the effect of thermal radiation. The flow past the sphere is considered steady, laminar and incompressible. The radiative transfer is modeled by P₀ and P₁ approximations. The mathematical model equations were discretized by the finite difference method. The discrete equations were solved by the defect correction – multigrid method. The influence of thermal radiation on the sphere surface temperature, concentration and reaction rate was analysed for three parameter sets of the dimensionless reaction parameters. The numerical results show that only for very small values of the Prater number the effect of thermal radiation on the surface reaction is not significant.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Heat transfer enhancement and hydrodynamic characteristics of nanofluid use in a micro heat exchanger is investigated for cooling electronic components working in hot climatic conditions. The cooling fluid employed was water and TiO2 nanoparticles at concentrations of 1% and 5%, Reynolds numbers ranged from 400 to 2000, and inlet temperatures ranged between 35ºC and 65ºC. At a nanofluid inlet temperature of 55ºC and a nanoparticle concentration of 1%, the Nusselt number increased by 23% up to 54% as the Reynolds number varied between 400 and 2000. At a nanoparticle concentration of 5%, the percentages which correspondingly enhanced the Nusselt number were 32% and 63%. The temperature of the electronic heating component decreased by 4.6-5.2ºC when the nanofluid concentration was increased from 0 to 5% at a Reynolds number of 400 and a nanofluid inlet temperature of 35ºC. Small increments in pressure drop of about 6% and 13% were observed at nanofluid concentrations of 1% and 5%, respectively. With nanoparticle concentrations of 1% and 5%, a Reynolds number of 2000 and a nanofluid inlet temperature of 35ºC, performance evaluation criterion (PEC) values of 1.36 and 1.45 were obtained. When the nanofluid inlet temperature was increased to 65ºC, the PEC parameter decreased to 1.02-1.10 for both concentrations.

Theoretical approaches were applied to study the effect of magnetic field and heat transfer on the flow of blood plasma through an asymmetric arterial segment. The plasma was considered to be unsteady, laminar and an incompressible fluid through non-uniform arterial segment in a two-dimensional flow. Axial velocity, pressure gradient, stream function and pressure shift per wavelength were evaluated in blood plasma flow in arteries by use of coupled linear partial differential equations, solved with the help of Finite difference method. The corresponding initial and boundary conditions were obtained by discretizing the flow channel. The effect of magnetic field on blood plasma in arteries was determined by creating a magnetic field gradient through the application of a varying strength of magnetic field on the flow. Heat transfer characteristics due to applied magnetic field and viscosity of blood was obtained by use of linear partial differential equations to determine varying temperature conditions in heat transfer characteristics. Numerical results for velocity profiles, magnetic profiles and temperature profiles were obtained to characterize blood plasma viscosity by use of various non-dimensional parameters. The results were graphically presented using MATLAB software. The results obtained helped in analyzing theoretically the effects of magnetic field and heat transfer in arterial plasma flow.

The exact determination of radiative exchanges between solids and surfaces has been a long sought-for question in heat transfer science. Being the canonical equation that rules such phenomena, a fourfold integral, it is extremely difficult to obtain an accurate solution like a formula or abacus. Over the last thirty years, the author has tried to integrate the canonical expression by sundry procedures and they have published two books and a dozen of articles on the matter, recently by virtue of computational geometry and graphic algorithms as a new way to solve the finite-difference problems that arise on complex geometries. In architectural engineering curved radiant emitters are customary since antiquity, especially in domes and vaults and their oculus, However, a consistent procedure to handle them was not readily available. The principles that are described hereby based on Cabeza-Lainez’ first principle for spherical fragments offer a complete panorama on the manner in which surface sources related or contained in spheres can be interpreted and accounted for without resorting to integration. The main advance is that a variety of unexplained problems of radiative heat transfer, applicable to aerospace engineering, meteorological, architectural and medical sciences can be sorted out as exactly as quickly.

This study will present a comprehensive review of the two-phase flow boiling heat transfer coefficient of hydrocarbons such propane (R-290), butane (R-600) and iso-butane (R-600a) and ethanol at various experimental conditions. Studying the multiphase flow heat transfer coefficient has a crucial importance for many heat transfer equipment to achieve higher efficiency for more compact design and cost reduction. One reason behind choosing hydrocarbons as refrigerants in this study is because hydrocarbons have zero ozone depletion potential (ODP=0) and insignificant direct global warming potential (GWP = 3). Moreover, thermodynamic and thermophysical characteristics of hydrocarbons qualify them to be a strong candidate for more heat transfer applications. Initially, by constructing a database for the working fluids from various experimental work available in the literature. The current data that this study has collected for the flow boiling of spans wide ranges of parameters, such as: mass flux, heat flux, operating pressure, and saturation temperature, etc. Furthermore, by comparing the experimental multiphase heat transfer coefficient database with the anticipated values of each correlation, the prediction performance of 26 correlations found in the literature was assessed. This study leads to the selection of the best prediction method based on the minimum deviation of predicted results from the experimental database provided by calculated mean absolute error (MAE) from the assessed correlations. The findings of this study can also be useful in the development of more accurate correlation methods for these fluids and improve the prediction of their flow boiling characteristics.

In this chapter we study the unstudy effect on MHD preamble porous medium through with thermal absorption and heat generation in the oscillatory flow of visco-elastic fluid between two plates in the presence of Chemical reaction. The expressions for the velocity, temperature and concentration distributions are arthemitiaclly solved by perturbation method.

To study the heat and mass transfer characteristics of an evaporative cooler for cooling high-temperature working fluids such as supercritical carbon dioxide, an experimental device of the evaporative cooler was built, and a corresponding test system was constructed. Then, the experimental study was carried out based on the orthogonal test method, and the law and extent of the influence of water flow in the tube, spray water flow rate, inlet water temperature in the tube, and air flow rate on heat dissipation, cooling efficiency, and heat and mass transfer coefficients have been obtained. The correlation equations of the heat and mass transfer coefficients were obtained by fitting the orthogonal experimental data, and the validity of the correlation equations was confirmed by the verification experiment.

As a new kind of highly compact and efficient micro-channel heat exchanger, printed circuit heat exchanger (PCHE) is a promising candidate satisfying the heat exchange requirements of liquefied natural gas (LNG) vaporization at low and high pressure. The effects of airfoil fin arrangement on heat transfer an flow resistance were numerically investigated using supercritical liquefied natural gas (LNG) as a working fluid. The thermal properties of supercritical LNG were tested by utilizing a REFPROF software database. Numerical simulation was performed using FLUENT. The inlet temperature of supercritical LNG was 121 K,and its pressure was 10.5MPa. The reference mass flow rate of LNG was set 1.22 g/s for the vertical pitch L_v = 1.67 mm and the staggered pitch L_s = 0 mm, with the Reynolds number of about 3750. The SST k-ω model with enhanced wall treatment was selected by comparing with the experimental data. The airfoil fin PCHE had better thermal-hydraulic performance than that of the straight channel PCHE. Moreover, the airfoil fins with staggered arrangement displayed better thermal performance than that of the fins with parallel arrangement. The thermal-hydraulic performance of airfoil fin PCHE was improved with increasing L_s and L_v. Moreover, L_v affected on the Nusselt number and pressure drop of airfoil fin PCHE more obviously. In conclusion, a sparser staggered arrangement of fins showed a better thermal-hydraulic performance in airfoil fin PCHE.

Plate fin-tube heat exchangers are widely used in air conditioning and refrigeration systems and other industry fields. Various errors made in the manufacturing process can result in the formation of an air gap between the tube and fin. Several numerical simulations were carried out for a symmetric section of plate fin-tube heat exchanger to study the influence of air gap on heat transfer under periodic flow conditions. Different locations and sizes of an air gap spanning 1/2 circumference of the tube were considered for the range of airflow velocities. Velocity and temperature fields for cases with air gap were compared with ideal thermal contact cases. Blocking of heat flow by the gap leads to the reduction of heat transfer rate. Fin discontinuity in the front of the tube causes the smallest reduction of the heat transfer rate in comparison to the ideal tube-fin contact, especially for thin slits. The rear gap position is the worst in the smallest gap range. Therefore, reversing the flow direction can lead to up to a 15% heat transfer increase, if mainly the rear gaps are present. The introduction of a thin slit in the front of the tube leads to convective heat transfer enhancement, which should be further investigated.

Abstract: In this study, a computational fluid dynamics (CFD) simulation was conducted to validate the CFD model with experimental data from Zimparov et.al (2012), which investigates the heat transfer performance in a spirally corrugated tube that has a twisted tape inserted. The heat transfer was then compared to a simple corrugated tube without the twisted tape and to a smooth tube with no corrugations and no twisted tape. This simulation is compared with a previous experimental study conducted by (Zimparov et al. 2012), which focuses on tubes with a height-to-diameter ratio e/Di > 0.04 and small relative pitches of the twisted tape, H/Di. The largest improvement was noticed in the tube with e/Di= 0.057 and ridge pitch-to-height ratio p/e=6.77 with a twisted tape of H/Di= 4.7. This tube is labeled 5035. Tube 5035 was found to have the most significant enhancement, hence the focus of the CFD simulation will be on this tube, and the simulation will range for Reynolds numbers, 3.5 x 103 < Re < 5.0 x 104. The focus of this simulation is the evaluation of heat transfer and friction factors; a metric was used to obtain an empirical representation of the tube’s performance. Keywords: Spirally corrugated tube; Twisted tape; Heat transfer enhancement; Friction factor; Nusselt number; Computational fluid dynamics (CFD); Star CCM+

Nonlinear thermal transport of non-Newtonian polymer flows is an increasingly important area in materials engineering. Motivated by new developments in this area which entail more re-fined and mathematical frameworks, the present analysis investigates the boundary layer ap-proximation and heat transfer persuaded by a symmetrical cylindrical surface positioned hori-zontally. To simulate thermal relaxation impacts the bioconvection cross nanofluid flow Buongiorno model is deployed. The impact of the magnetic field applied on the nanofluid using the heat generation and melting phenomena are inspected. The nonlinear effect of thermosolutal buoyant forces is incorporated into the proposed model. The novel mathematical equations comprise thermophoresis and Brownian diffusion effects. Via robust transformation techniques, the primitive resulting partial equations for momentum, energy, concentration, and motile living microorganism are rendered into nonlinear ordinary equations with convective boundary postulates. An explicit and efficient numerical solver procedure in Mathematica 11.0 programming platform is developed to engage the nonlinear equations. The consequence of multiple governing parameters on dimensionless fluid profiles is inspected through plotted visuals and tables. Finally, outcomes declared on the surface drag force, heat, and mass transfer coefficients are exhibited through 3D visuals via different influential parameters.

The amount of heat transfer in gas turbine blades depends on cooling techniques and various flow phenomena. The effect of eddies, passing shock waves and free flow turbulence has been noticed by many researchers since the beginning. The focus of the upcoming work is on the numerical investigation of the effects of turbulence intensity and Reynolds number on the amount of heat transfer from the blade surface with internal cooling. The SST model has been used to solve this problem, which has been compared with the experimental work to ensure the correctness of the numerical simulation. In this regard, by changing the free flow turbulence intensity with values of 1, 5, 7, and 10% and at three Reynolds numbers of 150,000, 350,000, and 750,000, the changes in heat transfer coefficients have been investigated. The results show that with the increase of the turbulence intensity at different Reynolds numbers, due to the positive effect of the flow turbulence on the suppression of separation and promotion of the boundary layer transition, the blade surface heat transferincreases and this increase is more evident at higher Reynolds numbers.

The heat and matter transfer during glucose catabolism in living systems and their relation with entropy production are a challenging subject of the classical thermodynamics applied to biology. In this respect, an analogy between mechanics and thermodynamics has been performed via the definition of the entropy density acceleration expressed by the time derivative of the rate of entropy density and related to heat and matter transfer in minimum living systems. Cells are regarded as open thermodynamic systems that exchange heat and matter resulting from irreversible processes with the intercellular environment. Prigogine’s minimum energy dissipation principle is reformulated using the notion of entropy density acceleration applied to glucose catabolism. It is shown that, for out-of-equilibrium states, the calculated entropy density acceleration is finite and negative and approaches as a function of time a zero value at global thermodynamic equilibrium for heat and matter transfer independently of the cell type and the metabolic pathway. These results could be important for a deeper understanding of entropy generation and its correlation with heat transfer in cell biology with special regard to glucose catabolism representing the prototype of irreversible reactions and a crucial metabolic pathway in stem cells and cancer stem cells.

The DNS of film boiling requires strong computational resources that are difficult to obtain for a daily CFD use by the practitioners of the industrial R&amp;D experts. On the other hand, the film boiling experiments are associated with the usage of the expensive and highly sophisticated apparatus, and the research to this end is found to be relatively difficult due to high heat flow rates that are present in the process itself. When combined with a transient heat conduction in a solid, the problem becomes significantly difficult. Therefore, a novel method in computation of conjugate heat transfer during film boiling in a quiescent liquid has been proposed in this paper. The method relies on the solution of mass, momentum and energy conservation equations in a two-fluid framework, supplemented with the appropriate closures. Furthermore, the turbulent flow has been found as an important parameter in obtaining the accurate solution of the temperature field evolution in a solid specimen, via the proper modeling of turbulent kinetic energy (TKE) value, that has been imposed as a constant value, i.e., the frozen turbulence approach. It was found, in addition, that the appropriate TKE value can be obtained by use of Kelvin-Helmholtz instability theory in conjunction with the boundary layer theory. The obtained results show excellent agreement with the experimental data within the first 15 s of the experiment, i.e., the first ca. 10 % of the total duration of the film boiling mode of heat transfer. Furthermore, the heat transfer coefficient has matched the error bands prescribed by the authors of the paper that has presented the correlations, whilst the averaged values are far beyond this band, i.e., are slightly more than 30 % higher. The further inspection has revealed a measure of similarity between the computational result of the volume fraction field distribution and the experiment, thus confirming the capability of the method to obtain realistic interface evolution in time. The method has shown full capability for further pursuing the industrial-scale film boiling problems that involve turbulent flow and the conjugate heat transfer approach.

The effect of thermal radiation on the two – dimensional, steady-state, conjugate heat transfer from a circular cylinder with an internal heat source in steady laminar crossflow is investigated in this work. P₀ (Rosseland) and P₁ approximations were used to model the radiative transfer. The mathematical model equations were solved numerically. Qualitatively, P₀ and P₁ approximations show the same effect of thermal radiation on conjugate heat transfer; the increase in the radiation – conduction parameter decreases the cylinder surface temperature and increases the heat transfer rate. Quantitatively, there are significant differences between the results provided by the two approximations.

Since the photocatalytic reaction is a surface reaction, enhancing the gas movement around photocatalyst would promote photocatalytic CO₂ reduction performance. A new approach to enhance the gas movement around the photocatalyst by the natural thermosiphon movement of gasses around photocatalyst using black body material was proposed and confirmed experimentally, but the heat transfer mechanism on the phenomena was not clarified yet. The purpose of this study is to clarify the heat transfer mechanism of it. This study calculated the temperature of mixed gases of CO₂ and NH₃ around P₄O₁₀/TiO₂ photocatalyst by the heat transfer formula. It is revealed that there was no difference between the increase temperature (T_g) from the temperature at the beginning of the CO₂ reduction experiment (T_ini) and the temperature of mixed gases of CO₂ and NH₃ measured by thermocouple in the experiment (T_e) under the illumination condition with a visible light (VIS) + an infrared light (IR) and IR only. The heat transfer model proposed by this study has predicted T_g well under the illumination condition with VIS + IR and IR only well. On the other hand, it is revealed that the difference between T_g and T_e was as large as 10 ℃ under the illumination condition with an ultra violet light (UV) + VIS + IR.

This article investigates the features of heat and mass transfer for the steady two-dimensional Williamson nanofluid flow across an exponentially stretched surface depending on suction/injection. The boundary conditions incorporate the impacts of the Brownian motion and thermophoresis boundary. The analysis of heat transfer is carried out for the two cases of prescribed exponential order surface temperature (PEST) and prescribed exponential order heat flux (PEHF). The ongoing flow problem is mathematically modeled under the basic laws of motion and heat transfer. The similarity variables are allowed to transmute the governing equations of the problem into a similarity ordinary differential equation (ODEs). The solution of this reduced non-linear system of ODEs is supported by the Homotopy analysis method (HAM). The combination of HAM arrangements is acquired by plotting the h-curve. In order to evaluate the influence of several emergent parameters, the outcomes are presented numerically and are plotted diagrammatically as a consequence of velocity, temperature and concentration proles.

Transient conjugate heat transfer measurements under varying temperature and velocity inlet boundary conditions at incompressible flow conditions were performed for flat plate and ribbed channel geometries. Therefrom local adiabatic wall temperatures and heat transfer coefficients are determined. Those data are analyzed using typical heat transfer correlations, e.g. Nu=CRe^mPr^n determining the local distribution of C and m. It is shown that they are closely linked. A relationship lnC=A−mB is observed with A and B as modeling parameters. They could be related to parameters in log law or power law representations for turbulent boundary layer flows. The parameter m is shown to have a close link to local pressure gradients and therewith near wall streamlines as well as friction factor distributions. A normalization of the C parameter allows to derive a Reynolds analogy factor and therefrom local wall shear stresses.

Circles, semicircles and its derived circular sectors are ubiquitous both in human creations and in the natural realm. However, mathematically speaking they have always represented a certain level of enigma or even mysticism since ancient times for being such a perfect shape that enclosed the irrational value that we now call π. Such figure was relatively unknown until the seventeenth century; polymaths like Guarini even equated it, after so many centuries, to the Archimedes fraction of 22/7 or sometimes 25/8 which, giving a value 3.125 introduces a considerable degree of error; Eventually, Lambert had to demonstrate, well advanced the eighteenth century that π was actually an irrational number. In recent years, the author has worked with sections of spheres and other curved bodies as related to radiative heat transfer and applied to the finding of form factors pertaining to such special geometries, to the point of defining new postulates. The main theorems so far enunciated refer to the radiative exchange between circles and half disks, but recently the possibility to treat circular sectors has arrived, thanks to the research already conducted in which, by virtue of Cabeza-Lainez first postulate, we are able to know the form factor of any spherical segment over itself, discarding in this way, the former uncertainties that appeared when dealing with the inner side of spherical surfaces. As it is known, to find the exact expression of the configuration factor by integration alone is mostly a tedious task and the results are not readily available as it has been frequently proved. In the said problem of the circular sectors, the author could integrate the first two steps of the basic formulation for radiant exchange. Subsequently, the novelty of the procedure lies in introducing a finite differences approximation for the third and fourth integrals which still remain unsolved, once that we have been able to find the first and second integrals of the form factor. This possibility had not been identified by former research. This sole output provides us with an ample variety of scenarios previously unforeseen. As a consequence, we would be able to analyze with more precision but freely, the spatial transference of radiant heat for figures composed of circular sectors such as spherical sectors like quarters or octaves of spheres. Many architectural, industrial or aircraft modules and objects fall into this category. We already know that spherical shapes cannot be discretized with any accuracy as there are no spherical tiles of the same size, therefore we hope to overcome with our finding a persistent extent of error. In this situation we are able to reduce a considerable amount of hindrances in the progress of thermal radiation science, due to the advances hereby presented. As the new formulations found can be adapted for algorithms, they will be integrated in simulation procedures with significant avail. Our achievement may be considered timely in the effort invested to square the elements of mathematics for radiative transfer. Important sequels are already being derived for radiation in the entrance to tunnels, aircraft design, low-energy building construction and also lighting and HVAC industries to cite just a few.

The Japanese Association for Acute Medicine Committee recently proposed a novel classification system for the severity of heat-related illnesses. The illnesses are simply classified into three stages based on symptoms and management or treatment. Stages I, II, and III broadly correspond to heat cramp and syncope, heat exhaustion, and heat stroke, respectively. Our objective was to examine whether this novel severity classification is useful in the diagnosis by healthcare professionals of patients with severe heat-related illness and organ failure. A nationwide surveillance study of heat-related illnesses was conducted between June 1 and September 30, 2012, at emergency departments in Japan. Among the 2130 patients who attended 102 emergency departments, the severity of their heat-related illness was recorded for 1799 patients, who were included in this study. In the patients with heat cramp and syncope or heat exhaustion (but not heat stroke), the blood test data (alanine aminotransferase, creatinine, blood urea nitrogen, and platelet counts) for those classified as stage III were significantly higher than those of patients classified as stage I or II. There were no deaths among the patients classified as stage I. This novel classification may avoid underestimating the severity of heat-related illness.

Exposure to extreme heat is a known risk factor that is associated with increased heat-related illness (HRI) outcomes. The relevance of heat wave definitions could change across the health conditions and geographies due to the heterogenous climate profile. This study compared the sensitivity of 28 heat wave definitions associated with HRI emergency department visits over five summer seasons (2011-2016), stratified by two physiographic regions (Coastal and Piedmont) in North Carolina. The HRI rate ratios associated with heat waves were estimated using the generalized linear regression framework assuming a negative binomial distribution. We compared the Akaike Information Criterion (AIC) values across the heat wave definitions to identify an optimal heat wave definition. In the Coastal region, heat wave definition based on daily maximum temperature with a threshold >90^th percentile for two or more consecutive days had the optimal model fit. In the Piedmont region, heat wave definition based on the daily minimum temperature with a threshold value >90^th percentile for two or more consecutive days was optimal. Additionally, we observed that the optimal heat wave definitions from this study captured moderate and frequent heat episodes than the national weather service (NWS) heat products that worked best for extreme heat episodes. This study compared the HRI morbidity risk associated with epidemiologic-based heat wave definitions and with NWS heat products. Our findings could be used for public health education and suggest recalibrating NWS heat products.

This study examines the effects of particle size and heat pipe angle on the thermal effectiveness of a cylindrical screen mesh heat pipe using silver nanoparticles as the test substance. The experiment investigates three different particle sizes (30nm, 50nm, and 80nm) and four different heat pipe angles (0°, 45°, 60°, and 90°) on the heat transmission characteristics of the heat pipe. The results show that the thermal conductivity of the heat pipe increased with an increase in heat pipe angle for all particle sizes, with the highest thermal conductivity attained at a 90° heat pipe angle. Furthermore, the thermal resistance of the heat pipe decreased as the particle size decreased for all heat pipe angles. The thermal conductivity measurements of the particle sizes - 30, 50, and 80 nm - were 250 W/mK, 200 W/mK, and 150 W/mK, respectively. The heat transfer coefficient values for particle sizes 30nm, 50nm, and 80nm were 5500 W/m2K, 4500 W/m2K, and 3500 W/m2K, respectively. The study also found that the heat transfer coefficient increased with increased heat pipe angle for all particle sizes, with the highest heat transfer coefficient obtained at a 90° heat pipe angle.

Proteins possess complex three-dimensional structures, and these structures are stable only within specific ranges of temperature which mostly correspond to the temperature ranges of the host organisms. However, few exceptional proteins, called heat-stable proteins, are stable at temperatures that are substantially higher than those tolerated by the host organisms themselves. Most of the heat-stable proteins possess heat stability to perform their functions at high temperatures, but some of them are intrinsically heat-stable due to their structure. Heat-stable proteins are usually divided into three or four groups depending upon the intricacies of their structures and thermal behaviors. Their peculiar property, i.e. heat-stability, makes them very valuable in applications such as polymerase chain reaction, industrial processes requiring high temperature, and protein engineering. Heat-stability also makes it feasible to purify such proteins, from the rest of the heat-labile proteins, using a simple heat-treatment method. Moreover, heat treatment can be used as a combined cell-lysis and protein purification step which, as compared to conventional methods, can result in a higher yield of heat-stable proteins. Furthermore, some special heat-stable proteins, i.e. intrinsically disordered proteins (which include the proteins involved in important neurodegenerative diseases), need heat-treatment step, in some cases, as the only way for their successful purification and study. Hence, this paper provides a first-ever comprehensive review of all major aspects of heat-stable proteins, i.e., their structure, evolution, classification, significance, and heat-treatment mediated purification.

Extreme heat is a climate, public health, and environmental justice issue. This case study examined public transit exposure and vulnerability to extreme heat by investigating the microenvironment, land cover characteristics, and social vulnerability of heat-vulnerable bus stops in Knoxville, Tennessee. The community’s temperature and Heat Index information, bus stop point data, land cover characteristics data, and the microenvironment of bus stops (i.e., trees and shelters) were processed and mapped with ArcGIS Pro. The pictures of the microenvironment of the bus stop were collected from Google Maps, and the social vulnerability of the area where the bus stops are located was investigated by analyzing the Center for Disease and Prevention's Social Vulnerability Index. Results found that the most heat-vulnerable bus stops were concentrated in West Knoxville, South, North, Northeast, and Northwest Knoxville. In addition, the most heat-vulnerable bus stops were concentrated in commercial complexes and areas a large number of systematically marginalized populations reside.

Maintaining the optimal microclimate in broiler houses is crucial for bird productivity, yet enabling efficient temperature control remains a significant challenge. This study developed and validated a computational fluid dynamics (CFD) model to predict temporal changes in indoor air temperature in response to variable ventilation operations in a commercial broiler house. The model accurately simulated air velocity and airflow distribution for different numbers of tunnel fans in operation, with air-velocity errors ranging from -0.22 to 0.32 m s-1. The predicted airflow rates through inlets and cooling pads showed good agreement with measured values with an accuracy of up to 108.1%. Additionally, the CFD model effectively predicted temperature dynamics, accounting for chicken heat production and ventilation effect. The model successfully predicted the longitudinal temperature gradients and their variations during ventilation cycles, validating its reliability through comparison with experimental data. The study also explored different variable inlet configurations to mitigate the temperature gradient. The variable inlet adjustment showed the potential to relieve the high temperatures but may reduce overall ventilation efficiency or intensify temperature gradients, which confirms the importance of optimising ventilation strategies. This CFD model provides a valuable tool for evaluating and improving ventilation systems and contributes to enhanced indoor microclimates and productivity in poultry houses.

High in reliability, multi in function, strong in tracking and detecting, active phased array antennas have been widely applied in radar system. Heat dissipation is a major technological barrier preventing the realization of next-generation high-performance phased array antennas. As a result of the advancement of miniaturization and the in-tegration of microelectronics technology, the study and development of embedded di-rect cooling or heat dissipation has significantly enhanced the heat dissipation effect. In this paper, a novel swept-back fishnet embedded microchannel topology (SBFEMCT) is designed, and various microchannel models with different fishnet runner mesh den-sity ratios and different fishnet runner layers are established to characterize the chip Tmax, runner Pmax, and Tmax and analyze the thermal effect of SBFEMCT under these two operating conditions. The Pmax is reduced to 72.37% and 57.12% of the original at mesh density ratios of 0.5, 0.25, and 0.125, respectively. The maximum temperature reduction figures are average with little change in maximum velocity and a small increase in maximum pressure drop for the number of fishing mesh runner layers of 0-4. This paper provides a study of the latest embedded thermal dissipation from the dimension of a single chip to provide a certain degree of new ideas and ref-erences for solving the thermal technology bottleneck of next-generation high-performance phased array antennas.

The condensing heat exchanger is commonly applied in various heat exchange systems. It can efficiently recover moisture and heat from the flue gas that contains water vapor. However, the convective-condensation heat transfer process is so complicated that no mature thermal calculation model is available. This study develops a thermal calculation model for the widely employed tubular condensing heat exchanger in industry. To characterize the degree of the heat and mass transfer, this study introduces two parameters, namely the sensible and latent heat transfer efficiencies of fin. The thermal calculations are conducted for the condensing heat exchangers reported in the literature to verify the proposed model by comparing it with the experimental data. The results show that the absolute error of the calculated sensible and latent heat transfer efficiencies is 0.0365 and 0.0268, respectively. Under the working conditions in this study, a maximum difference of 5.2 K has been acquired between the measured and calculated values of the outlet temperature. The relative error of the condensate water flowrate is mostly within ±5.0% and ±10.0% under the bare-tube and finned-tube conditions, respectively, with a maximum deviation of 0.7 and 1.4 kg h-1. This study provides a general model for designing and optimizing various tubular condensing heat exchangers accurately.

To achieve the required mechanical properties in the heat treatment of steel, it is necessary to have an adequate cooling rate and to achieve the desired final temperature of the product. This should be achieved with one cooling unit for different product sizes. In order to provide high variability of the cooling system, different types of nozzles are used in modern cooling systems. Designers often use simplified, inaccurate correlations to predict the heat transfer coefficient, resulting in oversizing of the designed cooling or failure to provide the required cooling regime. This typically results in longer commissioning times and higher manufacturing costs of the new cooling system. Accurate information about the required cooling regime and the heat transfer coefficient of the designed cooling is critical. This paper presents a design approach based on laboratory measurements. Firstly, the way to find or validate the required cooling regime is presented. The paper then focuses on nozzle selection and presents laboratory measurements that provide accurate heat transfer coefficients as a function of position and surface temperature for different cooling configurations. Numerical simulations using the measured heat transfer coefficients allow the optimum design to be found for different product sizes.

Abscisic acid (ABA) is a conserved “stress hormone” in unicellular organisms, plants and animals. In mammals, ABA and its receptors LANCL1 and LANCL2 stimulate insulin-independent cell glucose uptake and oxidative metabolism: overexpression of LANCL1/2 increases, and their si-lencing conversely reduces, mitochondrial number, respiration and proton gradient dissipation in muscle cells and in brown adipocytes. We hypothesized that the ABA/LANCL hor-mone/receptors system could be involved in thermogenesis. Heat production by LANCL1/2-overexpressing vs. double-silenced cells was compared in rat H9c2 cardiomyocytes with two different methods: differential temperature measurements using sensitive thermistor probes, and differential isothermal calorimetry. Results indicate that overexpressing cells generate an approx. double amount of thermal power compared with double-silenced cells, and that addition of ABA further doubles heat production in overexpressing cells. With the temperature probes, we find a time-scale of approx. 4 min for thermogenesis to “turn on” after nutrient addition. These results identify the ABA/LANCL hormone receptors system as a hitherto unknown regu-lator of cell thermogenesis. Pharmacologic means of increasing metabolic energy dissipation are considered a promising strategy to reduce oxidative stress and lipid accumulation at a cellular and organismic level: from this study, LANCL1-2 proteins emerge as targetable controllers of ther-mogenesis through their natural ligand ABA.

Chiral interactions play a crucial role in both chemistry and biology. Understanding the behavior of chiral molecules and their interactions with other molecules is essential, and chiral interactions in solutions are particularly important for studying chiral compounds. Chirality influences the physical and chemical properties of molecules, including solubility, reactivity, and biological activity. In this work, we used Isothermal Titration Calorimetry (ITC), a powerful technique for studying molecular interactions, including chiral interactions in solutions. We conducted a series of ITC measurements to investigate the heat of dilution and the heat of racemization of several amino acids (Asn, His, Ser, Ala, Met, and Phe). We also performed ITC measurements under different solute concentrations and temperatures to examine the effects of these parameters on chiral interactions, as well as the heat of dilution and racemization. The results of our measurements indicated that the heat of dilution, specifically the interactions between the solvent (water) and solute (chiral molecules), had a significant impact compared to the chiral interactions in the solution, which were found to be negligible. This suggests that the interactions between chiral molecules and the solvent play a more dominant role in determining the overall behavior and properties of the system. By studying chiral interactions in solutions, we can gain valuable insights into the behavior of chiral compounds, which can have implications in various fields, including drug design, chemical synthesis, and biological processes.

Abstract: The paper compares and analyses the effects of correctly and excessively executed heating cycles on flame straightening, far above the limits recommended by the steel manufacturer. The paperwork emphasizes the microstructural changes induced by overheating in the flame straightening process. Flame straightening is a flame heating process of metal constructions in which very limited areas of the construction are heated to the straightening temperature with the aim of inducing geometrical changes.The flame straightening process is used in most of metallic structure manufacturing companies. In many cases, it is not possible to carry out under economic conditions of metal structures without flame straightening.

Undisturbed ground temperature (UGT), thermal conductivity (TC) and heat capacity (HC) are essential parameters for the design of borehole heat exchanger (BHE) and borehole thermal energy storage systems. However, field methods to assess the thermal state and properties of the sub-surface are costly and time consuming. Moreover, HC is often not evaluated but arbitrarily selected from literature considering the geological materials intercepted by boreholes. Therefore, this work aims at proposing a field heat tracing method to infer the thermal diffusivity (TD) and HC with assumption of natural transient heat conduction in the subsurface. Empirical equations were developed to reproduce a UGT profile measured along a BHE. Experimental coefficients are found with a non-linear least square solver optimization and used to calculate the damping depth and TD. Subsequently, the TD is used to evaluate HC considering TC obtained from a thermal response test (TRT). Results from this proposed heat tracing method were verified and validated against a set of TRT results and oscillatory TRT analysis using a field dual probe concept to infer HC. The example here described highlights the advantages and novelty of this fast and simple field method relying only on a single UGT profile measured before a TRT.

Heat stress on workers wearing PPE(Personal protective equipment) in hot outdoor environments is of rising concern, especially in cases when rest breaks and clothing changes are impractical. Mist fan evaporative cooling could provide low-energy continuous cooling even during work activity. The cooling effect of a misting fan was compared to that of a fan alone, as well as natural convection. A thermal mannequin with heat flux sensors at 8 body locations was exposed to an outdoor misting fan while clothed in typical work clothes and PPE. Work clothes were dry or saturated with water to simulate sweat. The distance from the misting fan ranged from 4m (wetting common) to 7m (wetting unlikely). On average, the misting fan had a cooling effect of 0.31met (18.3W/m²) higher than natural convection when PPE with wet work clothes are worn, and 0.35met (10.63W/m²) higher when dry work clothes with PPE were worn. This equates to reducing thermal metabolic load from light industrial work to walking about in office work, or from standing to reclining. Under international standards for workers in hot environments based on metabolic rate and WBGT(wet bulb globe temperature), such as ISO 7243, this equate to an average of about a 0.35ºC (dry clothes with PPE) to 0.61ºC (wet clothes with PPE) increase in acceptable WBGT.

Cross flow heat exchangers are commonly used in the thermal industry to transfer heat from hot tubes to cooling fluid. To protect the heat exchanger tubes from corrosion and dust accumulation, microscale coatings are often applied. In this study, we present machine-learning models for predicting heat transfer from hot tubes with different micro-sized coatings to cooling fluid in a turbulent flow using computational fluid dynamics simulations. A dataset of approximately 1000 cases was generated by varying the coating coverage thickness of each tube, the inlet Reynolds number, fluid flow inlet temperature, and wall temperature of tubes. The machine-learning models were generated to predict the overall heat flow rate in the heat exchanger, and it was found that combining the features based on their importance preserved the accuracy of the models while maintaining all the relevant information. The simulation results demonstrate that the proposed method increases the coefficient of determination (R2) for the models. The R2 values for unseen data for Random Forest, K-Nearest Neighbors, and Support Vector Regression were 0.9810, 0.9037, and 0.9754, respectively, indicating the usefulness of the proposed model for predicting heat transfer in various types of heat exchangers.

Motivated by the well-known contradiction of special relativity and the heat equation, a wave equation for temperature scalar field is presented that also resolves the old controversy of (Lorentz) transformation of temperature and entropy. After showing that the current dogma of temperature and entropy being emergent concepts is based on but a logical fallacy, it is proposed that single particles posses entropy. This principle of fundamentality of entropy is then shown to be compatible with the equipartition theorem by yielding corrections in the quantum gravity regime.

A temperate deep lake, Lake Kuttara, Hokkaido, Japan (148 m deep at maximum) was completely frozen every winter in the 20th century. However, unfrozen conditions of the lake over winter occurred four times in the 21st century, which is probably due to global warming. In order to understand how thermal regime of the lake responds to climate change, its heat storage change was calculated by estimating heat budget of the lake and monitoring water temperature at the deepest point for September 2012–June 2016. As a result, temporal change of the heat storage from the heat budget was very consistent with that from the direct temperature measurement (determination coefficient R² = 0.827). The 1978–2017 data at a meteorological station near Kuttara indicated that there are significant (less than 5% level) long-term trends for air temperature (0.024 °C/yr) and wind speed (−0.010 m/s/yr). A sensitivity analysis for the heat storage from the heat budget estimate and an estimate of return periods for mean air temperature in mid-winter allow us to conclude that the lake could be unfrozen once per about two year in a decade.

The air side thermal hydraulic performance of multi-louvered aluminium fin heat exchangers is investigated. A detailed study was performed to analyse the thermal performance of air over a wide range of Reynolds number i.e. from 30 to 250. Air-side heat transfer coefficient and air pressure drop were calculated and validated over the mentioned band of Reynolds numbers. Critical Reynolds number was determined numerically and the variation in flow physics along with the thermal and hydraulic performance of microchannel heat exchanger associated with R_cri has been reported. Moreover, a parametric study of the multi-louvered aluminium fin heat exchangers was also performed for 36 heat exchanger configurations with the louver angles (19-31°), fin pitches (1.0, 1.2, 1.4 mm) and flow depths (16, 20, 24 mm); and the geometric configuration exhibiting the highest thermal performance was reported. The air-side heat transfer coefficient and pressure drop results for different geometrical configurations were presented in terms of Colburn j factor and Fanning friction factor f, as a function of Reynolds number based on louver pitch.

Background: Numerous risk factors have been recognized as significant contributors to outdoor workers' heat stress and the risk of heat-related conditions, impacting their health, well-being, and productivity. However, the specific effects of these factors on construction workers' safety, health, and well-being remain under-researched. With climate change increasing temperatures, assessing heat stress among construction workers is imperative. Objective: To identify the barriers and facilitators influencing the safety of natural gas construction workers and evaluate an implemented heat stress intervention. Methods: In the summer of 2023, two semi-structured interviews and six focus groups were conducted with twenty-one stakeholders at a Texas natural gas construction site. Results: Key facilitators include employee preparedness, use of employer-provided resources, hydration logs, and real-time communication tools. Contrarily, the barriers include daily work schedules, access to dehydrating beverages, and generational differences with the non-implementation of mandatory rest breaks. The heat stress program was perceived as effective, surpassing recommended guidelines. Conclusion: To advance construction workers’ safety, health, and well-being, both employee involvement and employer management are needed, along with no-cost accessible resources. Additionally, implementing a required routine rest break and comprehensive heat stress education, particularly for older workers, will significantly promote safety and safe work practices in hot environments.

Ocean surface heat fluxes play a significant role in the genesis and evolution of various marine-based atmospheric phenomena, from the synoptic scale down to the microscale. While in-situ measurements from buoys and flux towers will continue to be the standard in regards to surface heat flux estimates, they commonly have significant gaps in temporal and spatial coverage. Previous and current satellite missions have filled these gaps; though they may not observe the fluxes directly, they can measure the variables needed (wind speed, temperature, and humidity) to estimate latent and sensible heat fluxes. However, current remote sensing instruments have their own limitations, such as infrequent coverage, signals attenuated by precipitation, or both. The Cyclone Global Navigation Satellite System (CYGNSS) mission overcomes these limitations over the tropical and subtropical oceans by providing improved coverage in nearly all weather conditions. While CYGNSS (Level 2) primarily estimates surface winds, when coupled with observations or estimates of temperature and humidity from reanalysis data, it can provide estimates of latent and sensible heat fluxes along its orbit. This paper describes the development of the Surface Heat Flux Product for the CYGNSS mission, its current results, and expected improvements and changes in future releases.

Under the increasingly severe global heat threat, continuous high temperature has far-reaching effects on plant growth and development and become a major constraint to crop production. The development of heat-resistant varieties has become research hotspot in many fields, and it is also necessary to establish effective identification methods. In this study, twenty Brassica rapa varieties were selected to to investigate the physiological and biochemical characteristics under heat stress, explore the relationship between physiological response and the heat resistance mechanism, select some typical heat-resistant and heat-sensitive varieties. The effects of photosynthetic electron transfer and antioxidant pathway on heat resistance of Brassica rapa were identified. These findings will providing an important reference for the physiological regulation and identification method of high-temperature stress in plants.

Increasing wind speed alleviates physiological heat strain, however, health policies have advised against using ventilators or fans under heat wave conditions with air temperatures above the typical skin temperature of 35 °C. Recent research, mostly with sedentary participants, suggests mitigating effects of wind at even higher temperatures depending on the humidity level. Our study aimed at exploring and quantifying, whether such results are transferable to moderate exercise levels, and whether the Universal Thermal Climate Index UTCI reproduces those effects. We measured heart rates, core and skin temperatures and sweat rates in 198 laboratory experiments completed by five young, semi-nude, heat-acclimated, moderately exercising males walking the treadmill with 4 km/h on the level for three hours under widely varying temperature-humidity combinations and two wind conditions. We quantified the cooling effect of increasing wind speed from 0.3 to 2 m/s by fitting generalized additive models predicting the physiological heat stress responses depending on ambient temperature, humidity and wind speed. We then compared the observed wind effects to the assessment performed by UTCI. Increasing wind speed lowered physiological heat strain for air temperatures below 35 °C, but also for higher temperatures with humidity levels above 2 kPa water vapour pressure concerning heart rate and core temperature, and 3 kPa concerning skin temperature and sweat rate, respectively. UTCI assessment of wind effects correlated positively with the observed changes in physiological responses, showing the closest agreement (r=0.9) for skin temperature and sweat rate, where wind is known for elevating the relevant convective and evaporative heat transfer. These results demonstrate the potential of UTCI for adequately assessing sustainable strategies for heat stress mitigation involving fans or ventilators depending on temperature and humidity for moderately exercising individuals.

The Laser Thermal-Joule Heating Composite Process was studied by orthogonal tests based on an analysis of fabrication parameters such as the laser power, wire feeding speed, and electric current. Temperature profiles and the geometric morphology of deposited layers under different process parameters were analyzed, and the overlaps between the layers and the substrate were observed. Results show that when the temperature at the bottom layer of the additive manufacturing is higher than the melting point of the substrate, and the highest temperature at the top layer does not exceed the over-firing temperature, good morphology and close bonding with the substrate can be obtained. Finally, appropriate process parameters were identified and verified to print multiple layers continuously.

Metal-Organic Frameworks (MOFs) are a subclass of porous materials that have unique properties such as varieties of structures from different metals and organic linkers, tunable porosity from a structure or framework design, etc. Moreover, modification/functionalization of the material structure could optimize the material properties and demonstrate high potential for a selected application. MOF materials exhibit exceptional properties and make these materials widely applicable including in energy storage and heat transformation applications. This review aims to give a broad overview of MOFs and their development as adsorbent materials having the potential for heat transformation applications. We summarize current investigations, developments, and possibilities of metal-organic frameworks (MOFs) especially the tuning of the porosity and hydrophobic/hydrophilic design required for this specific application. These materials applied as adsorbent are promising in the thermal driven adsorption for heat transformation using water as working fluid and related application.

With heat treatments to control drywood termites (Blattodea: Kalotermitidae), the presence of heat sinks causes heat to be distributed unevenly throughout the treatment areas. Drywood termites may move to galleries in heat sink areas to avoid exposure to lethal temperatures. Our studies were conducted in Crytotermes brevis-infested condominiums in Honolulu, Hawaii to reflect real-world condominium scenarios; either a standard heat treatment performed by a heat remediation company or an improved heat treatment was used. For improved treatments, heated air was directed into the toe-kick voids of C. brevis infested cabinets to reduce heat sink effects and increase the heat penetration into these difficult-to-heat areas. Eight thermistor sensors placed inside toe-kick voids, treatment zone, embedded inside cabinets’ sidewalls, and in a wooden cube recorded target temperatures of above 46 °C or 50 °C for 120 minutes. A pretreatment and follow-up inspections were performed at 6 months posttreatment to monitor termite inactivity using visual observations and by recording the numbers of spiked peaks on a microwave technology termite detection device (Termatrac). In improved treatment condominiums, significantly higher numbers of spiked peaks were recorded at pretreatment as compared to 6 months posttreatment. Efficacious heat treatment protocols using the improved methods are proposed.

Due to the complexity of the microstructure of porous media, it is of great significance to explore the heat transport mechanism in porous media in many engineering applications. In this study, an expression for effective thermal conductivity（ETC） of porous media with randomly distributed damaged tree-like bifurcation networks is derived based on the theory of thermodynamics and fractal features of tree-like bifurcation networks. We investigate the effect of heat conduction and heat convection in porous media with randomly distributed damaged tree-like bifurcation networks on the ETC of the porous media. It is found that our fractal model is in good consistency with the existing available experimental data. In addition, the influence of the micro-structural parameters of the model on heat transfer in the porous media have been analyzed in detail. The research results can provide significant theoretical guidance for the development and design of heat transfer systems.

Testicular heat stress is a well described phenomenon that occurs in mammals that possess a scrotum. Different models to induce testicular hyperthermia, such as surgical cryptorchidism, hot water bath, scrotal insulation or increased environmental temperature have all shown that spermatocytes and spermatids are unambiguously affected by high temperature, resulting in poor sperm production weeks later. Furthermore, a body of evidence suggest the involvement of oxidative stress is either a major or contributory pathway, which gives rise to the potential to overcome this condition. Whilst experimental models conclusively show the deleterious effect of testicular heat on sperm quality, the physiological relevance of the work is still debated. Herein we summarise a cohort of studies that report the effect of “season” on sperm quality. The data show season can affect sperm production, motility and morphology depending on where the work was performed. In countries where temperatures drop below zero, there is evidence showing summer conditions tend to improve semen quality. However, in sub-tropical countries, some studies show a decrease in summer, whilst others show no change. Herein we offer a reasonable explanation for this apparent controversy and present a range of antioxidant supplements that may offer some protection against testicular hyperthermia.

Heat using behavior has a large impact on in heating energy in heat metering system, and therefore a better understanding can assist in behavior guidance to reduce energy. To understand the current situation of indoor thermal environment and heat using behavior for heat metering households in northern China, including adjusting heating end valves and operating windows, 30 households were measured and surveyed. The factors influencing heat using behavior, including outdoor and indoor environmental parameters and time of the day, were analyzed. The results are :1) Thermal neutral temperature for heat metering households is relatively high, up to 24.5℃; 2) The heat using behavior of households is lack of rationality: low proportion of active households; high indoor temperature setting; more frequency of window opening. Improving indoor comfort is the main reason for households to adjust the heating end valve, and only 7.15% of households have considered the economic benefits brought by adjusting the valve. " Thermostat control valve does not work" is the main reason for households without adjustment; 3) Time of the day and indoor temperature affect active households’ willingness to adjusting heating end valve. Time of the day, indoor temperature and outdoor temperature have impacts on opening window during heating period.

A solid structure, such as a road, building wall or envelop, used as a solar collector is considered an effective and new way to use renewable energy. This paper focused on the temperature characteristics of four structures exposed to sunshine: asphalt, red brick, composite cement and concrete road slab. Furthermore, the collected heat based on a hydraulic system was investigated experimentally. For the four structure slabs, their temperature differences are due to solar radiation absorption varied greatly by the material’s heat absorptance and color. Through the test, asphalt slab attained the highest temperature and had the weakest reflection among the structures. Compared with the others, the temperature of the asphalt slab was greater by 8.1%, 14.9% and 16.4% than the brick, composite cement and concrete, respectively. The reflection intensity growth ratio was defined and indicates the growth potential for absorbing radiation in the solid slab surface. From the experiments, it was concluded that a suitable selection of road materials can greatly improve the thermal absorption, conduction and penetration into the solid slab. The collected heat capability was approximately 250 W/m2 to 350 W/m2 in the natural summer condition. A black coating or a surface modification can collect more heat, reaching greater than 250 W/m2. The solar collecting heat efficiency with a surface configuration of the road slab can reach above 30% in the summer time.

Three-temperature heating systems consist of a heat engine and a heat pump, enabling thus maximum usage of the primary thermal source for the heating of buildings. This analysis has revealed obvious advantages and disadvantages that the combining of thermodynamic systems has in future development, also with respect to environmental and economic issues. It appears that the combination of a Stirling engine or a similar heat drive with a heat pump is especially suitable. In order to analyze the effectiveness of such a system, a comprehensive calculation procedure is used: its basis lies in accounting for all types of energy and their relationship to the original natural resource. The present paper aims to point out that the combination of Stirling engine and a heat pump is a useful solution thanks to the most favorable resultant economic impact if compared to the usage of a diesel, four-stroke gas, or, most commonly used, electric drive.

Enhancing the Efficiency of Natural Gas Liquid (NGL) Extraction and Fractionation Trains: An Integrated Approach of Simulation Analysis, Advanced Modifications, and Technological Advancements. Through comprehensive research, innovative solutions such as the heat pump aided distillation (HPAD) system and self-heat recuperation technology (SHRT) have been developed to significantly reduce the energy consumption associated with conventional distillation systems. To identify a practical system for NGL fractionation trains, this study extensively examined and compared various HPAD and SHRT options to retrofit a single column. The objective was to find the most suitable and efficient solution for the fractionation process of natural gas liquids (NGLs). The retrofit options analyzed in this study encompassed a range of techniques, including vapor compression (VC), mechanical vapor re-compression (MVR), thermal vapor re-compression (TVR), bottom flashing (BF), side heat exchanger (SHE), intermediate heating and cooling (IHC), self-heat recuperative (SHR), and modified self-heat recuperative (MSHR) distillation. These methods were carefully examined to determine their suitability and effectiveness in improving the performance of NGL fractionation trains.In this study, a depropanizer column, typically employed in conventional NGL plants, was selected as a case study. The simulation software Aspen HYSYS V7.3 was employed to model and analyze eight retrofit designs based on predefined criteria. The simulation data was carefully evaluated to identify the most efficient design for minimizing energy consumption. Among the retrofit options, the mechanical vapor re-compression (MVR) technique demonstrated the most significant energy cost reduction, with a remarkable 68.11 percent improvement compared to the base case conventional column. These findings highlight the potential of MVR as an effective solution for lowering energy costs in NGL fractionation trains.Following the MVR retrofit option, the study found that vapor compression (VC) achieved a considerable energy cost reduction of 66.65 percent, closely followed by modified self-heat recuperative (MSHR) at 64.02 percent, bottom flashing (BF) at 62.88 percent, self-heat recuperative (SHR) at 55.85 percent, side heat exchanger (SHE) at 54.23 percent, intermediate heating and cooling (IHC) at 39.54 percent, and thermal vapor re-compression (TVR) also at 39.54 percent. These findings highlight the significant potential for energy savings offered by these retrofit options, with VC being the most popular choice, closely followed by MSHR, BF, SHR, SHE, IHC, and TVR.

Battery-powered electric vehicles (EVs) have emerged as an environmentally friendly and efficient alternative to traditional internal combustion engine vehicles, while their single-charge driving distances under cold conditions are significantly limited due to the high energy consumption of heating systems. Heat pumps can provide an effective heating solution for EVs, but their coefficient of performance (COP) is hampered by heat transfer deterioration due to frost accumulation. This study proposes a solution to this issue by introducing a microchannel heat exchanger (MHE) with superhydrophobic surface treatment (SHST) as a heat pump evaporator. A computational-fluid-dynamics MHE model and a dynamic heat pump model are developed and rigorously validated to examine the detrimental impact of frost accumulation on heat transfer, airflow resistance, and heat pump performance. When the frost layer thickness is 0.8 mm at a given air-side velocity of 1.0 m/s, the air-side heat transfer coefficient can be reduced by about 75%, and the air-side pressure drop sharply increases by 28.4 times. As frost thickness increases from 0 to 0.8 mm, the heating effect drops from 3.97 to 1.82 kW, and the system COP declines from 3.17 to 2.30. Experimental results show that the frost thickness of the MHE with SHST reaches approximately 0.4 mm after 30 minutes, compared to that of 0.8 mm of the MHE without SHST, illustrating the defrosting capability of the superhydrophobic coating. The study concludes by comparing the performance of various heating methods in EVs to highlight the advantages of SHST technology. As compared to traditional heat pumps, the power consumption of the proposed system is reduced by 48.7% due to the defrosting capability of the SHST. Moreover, the single-charge driving distance is extended to 327.27 km, an improvement of 8.99% over the heat pump without SHST.

Economic expedience of waste heat recovery systems (WHRS), especially for low temperature difference applications, is often questionable due to high capital investments and long pay-back periods. By its simple design isobaric expansion (IE) machines could provide a viable pathway to utilize otherwise unprofitable waste heat streams for power generation and particularly for pumping liquids and compression of gases. Different engine configurations are presented and discussed. A new method of modelling and calculation of the IE process and efficiency is used on IE cycles with various pure and mixtures as a working fluid. Some interesting cases are presented. It is shown in this paper, that the simplest non-regenerative IE engines are efficient at low temperature differences between a heat source and heat sink. Efficiency of non-regenerative IE process with pure working fluid can be very high approaching Carnot efficiency at low pressure and heat source/heat sink temperature differences. Regeneration permits to increase efficiency of the IE-cycle to some extent. Application of mixed working fluids in combination with regeneration permits to significantly increase the range of high efficiencies to much larger temperature and pressure differences.

The research examines the relationship between self-rated health situation and personal percep-tion of heat waves, and how social linkage of communities would be a moderator variable in residents’ perception of heat waves in Taiwan. This study uses the questionnaire conducted by Sinica “Responsive Capacity under Heat Wave: The Perspectives of the Locals”(2019), using OLS method for estimating the unknown parameters in multiple regression model. The author finds that the correlation of self-rated health situation and perception toward heat is significantly posi-tive. Also, social linkage in communities affects strongly as a moderator variable: While the sat-isfaction to with their community could reduce negative reaction to heat, contacts with neighbors could increase possibility people feel uncomfortable in high-temperature situation. This study ex-hibits the effects of social environment on community, and expects further related researches or practices to strengthen capability to resist heat wavesƒ for Taiwanese residents.

This paper shares some new information on the ambient temperature profile and the heat stress occurrences directly underneath ground-mounted Solar Photovoltaic (PV) Arrays (monocrystalline-based) focusing on different temperature levels. A common ground for this work lies on the fact that 10C increase of PV cell temperature results in reduction of 0.5% energy conversion efficiency thus any means of natural cooling mechanism would gain much benefit especially to the Solar Farm operators. Transpiration process plays an important role in the cooling of green plants where in average it could dissipate around 32.9% of the total solar energy absorbed by the leaf making it a good natural cooling mechanism. This condition is relatively applied for herbs specifically for this project, Orthosiphon Stamineus or generally known as Java Tea are used as the high value crops. The thermal process via convective heat and mass exchange of leaves with the environment is relevant for a better understanding of plant physiological processes in response to environmental conversion factors for a wide range of applications. An important fact for plant heat stress with respect to the Ambient temperature is that the range lies between 10 C to 15 C above the surrounding value. This heat stress condition is relatively important and should be modelled in crops-energy integration. Agrivoltaic concept is a system that combines commercial agriculture and photovoltaic electricity generation in the same space. The concept is in line with the Kyoto Protocol and the United Nation Sustainable Development Goals (UN-SDG) which highlights the clean energy and sustainable urban living. The integration of agrivoltaic systems would optimize the yield, improving clean system efficiency and solving the issue of land resource sustainability. The PV bottom surface temperature are the main source of dissipated heat as shown in the thermal images recorded at 5 minutes interval at 3 sampling time. Statistical analysis shows that the Thermal correlations for transpiration process and heat stress occurrences between PV bottom surface and plant height will be an important finding for large scale plant cultivation in agrivoltaic farms.

Flying-fox populations are increasingly threatened by heat events, starvation events and other stressors due to habitat clearing and human/flying-fox conflict.These factors are unlikely to resolve, meaning that a well-coordinated and timely approach to flying-fox disasters is imperative for the mitigation of further flying-fox population impacts.