Grouting materials with good insulation and reinforcement performance are key factors in solving the temperature control problem of high temperature tunnels using curtain grouting, while existing grouting materials cannot balance their working performance and insulation performance in high-temperature environments. In response to the above issues, this article uses red mud to prepare high ground temperature red mud based grouting materials (RMGS), and conducts tests on the working performance (viscosity, setting time, compressive strength) and insulation performance (thermal conductivity, specific heat capacity) of grouting materials at different temperatures (20, 40, 60, and 80 ℃), and analyzes the variation patterns and micro mechanisms of various characteristics with temperature. The results indicate that an increase in temperature will accelerate the viscosity development and condensation of the grouting material, and lead to a decrease in thermal conductivity and specific heat capacity. In addition, an appropriate temperature can also improve the compressive strength of the material. The increase in temperature will accelerate the hydration reaction rate of the grouting material and the development of internal pores, which is the reason why temperature affects the performance of the grouting material. In engineering applications, cement slurry is suitable for static water grouting, cement-sodium silicate slurry is suitable for dynamic water grouting, and RMGS is suitable for high-temperature tunnel grouting.

This study investigated the efficacy of carvone, abscisic acid (ABA), gibberellin (GA3), and variable temperature in managing dormancy and sprouting in aeroponically grown mini-tuber potato seeds. Results showed that carvone treatment effectively reduced weight loss rate by 12.25% and decay rate by 3.33% at day 25, compared to control. ABA treatment significantly enhanced germination rate to 97.33%. GA3 treatment resulted in the longest sprouts of 14.24 mm and reduced MDA content by 23.08% at day 30, indicating its potential in shortening dormancy and maintaining membrane integrity. Variable temperature treatment showcased a balanced performance in reducing weight loss and maintaining a lower relative conductivity, indicating less cellular damage. Enzymatic activities of α-amylase, CAT, and SOD were modulated by the treatments, ensuring a balanced enzymatic environment for seed vitality. These findings provide a robust foundation for refining post-harvest management strategies to optimize germination uniformity and preserve the quality of aeroponic potato seeds during extended dormancy, promising enhanced yield and productivity in potato cultivation.

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

This study presents a comprehensive investigation of the formation, composition, and behaviour of oxide layers during the high-temperature oxidation of four different steel alloys (16Mo3, 13Cr, T24 and P91) at a uniform temperature of 650 °C. The research combines CALPHAD (CALculation of PHAse Diagrams) calculations, thermogravimetric analysis (TGA) and advanced microscopy techniques, including scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD), to elucidate the complex mechanisms controlling oxidation kinetics and oxide layer development. CALPHAD calculations were used to determine the thermodynamically stable phases for each steel type at 650 °C. The results showed different phase compositions, highlighting the importance of steel composition in the formation of oxide layers. Each steel grade exhibited different kinetics, with 16Mo3 steel showing the highest oxidation rate, followed by 13Cr, T24 and P91. This variability highlights the role of steel composition, particularly chromium content, in determining oxidation behaviour. These results have significant implications for temporary overheating in industrial applications and contribute to a deeper understanding of oxidation processes in steels.

Pressure-sensitive paint (PSP) has received significant attention for capturing surface pressure in recent years. One major source of uncertainty in PSP measurements, temperature dependency, stems from the fundamental photophysical process that allows PSP to extract pressure information. The motion-capturing PSP method, which involves two luminophores, is introduced as a method to reduce the measurement uncertainty due to temperature dependency. A theoretical model for the pressure uncertainty due to temperature dependency is proposed and demonstrated using a static pressure measurement with an applied temperature gradient. The experimental validation of the proposed model shows that the motion-capturing PSP method reduces the temperature dependency by 37.7% compared to the conventional PSP method. The proposed model also proves that a PSP with zero temperature dependency is theoretically possible.

Fibre reinforced concrete (FRC) has been used for decades in certain applications of the construction industry, such as tunnel linings and precast elements, but has experienced an important progress in recent times, boosted by the inclusion of guidelines for their use in some national and international standards. Traditional steel fibres have been studied in depth and their performance is well known although in recent years new materials have been proposed as possible alternatives. Polyolefin macro-fibres, for instance, have proven to enhance the mechanical properties of concrete and the parameters that define their behaviour (fibre length, fibre proportion or casting method, for instance) have been identified. These fibres overcome certain traditional problems related to steel fibres, such as corrosion or their interaction with magnetic fields, which can limit the use of steel in some applications. The behaviour of polyolefin fibre reinforce concrete (PFRC) has been numerically reproduced with success through an embedded cohesive crack formulation that uses a trilinear softening diagram to describe the fracture behaviour of the material. Furthermore, concrete behaves well under high temperatures or fire events, especially when it is compared with other construction materials, but the behaviour of PFRC must be analysed if the use of these fibres is to be extended. To this end, the degradation of PFRC fracture properties has been recently experimentally analysed under a temperature range between 20ºC and 200ºC. As temperature increases, polyolefin fibres modify their mechanical properties and their shape, which reduce their performance as reinforcement of concrete. In this work, those experimental results, which include results of low (3 kg/m3) and high (10 kg/m3) proportion PFRC specimens, are used as reference to study the fracture behaviour of PFRC exposed to high temperatures from a numerical point of view. The experimental load-deflection diagrams are reproduced by modifying the trilinear diagram used in the cohesive model, which helps to understand how the trilinear diagram parameters are affected by high temperature exposure. Finally, some expressions are proposed to adapt the initial trilinear diagram (obtained with specimens not exposed to high temperature) in order to numerically reproduce the fracture behaviour of PFRC affected by high temperature exposure.

We consider an $N$ fermion system at low temperature $T$ in which we encounter special particle number values $N_m$ exhibiting special traits. These values arise in focusing attention upon the degree of mixture (DM) of the pertinent quantum states. Given the coupling constant of the Hamiltonian, the DMs stay constant for all $N$-values, but experience sudden jumps at the $N_m$. For a quantum state described by the matrix $\rho$, its purity is expressed by $Tr \rho^2$ and then the degree of mixture is given by $1 - Tr \rho^2$, a quantity that coincides with the entropy $S_q$ for $q=2$. Thus, Tsallis entropy of index two faithfully represents the degree of mixing of a state, that is, it measures the extent to which the state departs from maximal purity . Macroscopic manifestations of the degree of mixing can be observed through various physical quantities. Our present study is closely related to properties of many-fermion systemsn that are usually manipulated at zero temperature. Here we wish to study the subject at finite temperature. Gibbs' ensemble is appealed to. Some interesting insights are thereby gained.

Nickel base superalloy GH4169 is a material with strong mechanical properties and is difficult to process. In order to reduce tool wear during material processing and improve workpiece surface processing quality, based on the finite element simulation software DEFORM, the influence of n, ap, and fz parameters on tool wear during carbide tool milling GH4169 was studied, and a simulation orthogonal experimental model was established, The prediction model of tool wear is obtained; The ultrasonic vibration milling is compared with ordinary milling, and the improvement degree of different coating materials on carbide tool wear is explored. The results show that the ultrasonic vibration signal is helpful to reduce tool wear, improve the surface quality of the workpiece, and improve the stability of the milling process. TIALN/TIN (WC) composite coated tools have good cutting performance, help to reduce tool temperature, reduce tool wear, and improve tool life.

With permafrost degenerating caused by climate change, water accumulation increases in permafrost regions during last decades. Water accumulation will deteriorate existing status of engineering in cold regions. Water accumulation can make a thermal effect on permafrost under construction, even result in failure of the subgrade. Moreover, the thermal effect is related to water temperature. However, temperature variation of water accumulation is complex, and its influence factors include air temperature, environment, scope of water accumulation and so on. In order to make analysis of the damage mechanism of water accumulation on permafrost, it is necessary to explore the internal temperature change of water accumulation. This paper proposes a review about temperature calculation method of water accumulation in cold environment. The thermal calculation method between air and water boundary of water accumulation is summarized. Water temperature change of water accumulation with various type is analyzed. The thermal calculation considering phase transformation in water accumulation is discussed, and heat transfer from the bottom of water accumulation to the underlying soil is further studied. Finally, the key factors which are advantageous to make research about the thermal effect of water accumulation in permafrost is proposed to optimize calculation method.

Low-temperature accumulation is one of the essential stages in the growth process of woody ornamental plants. In this study, two different low-temperature treatments, 6℃ and 10℃, were used to analyze the effects of different low-temperature treatments on dormancy release and flowering of the 'Gulihong' plant using artificial low temperatures. Based on the experimental results, four typical early-blooming Prunus mume cultivars widely planted in Yangling area of Henan Province, China, including 'Zaoyudie', 'Zaohualve', 'Nanjing gongfen', and 'Gulihong', were selected as the experimental materials. The effects of low-temperature accumulation on the flowering characteristics of different cultivars were analyzed using a 6℃ artificial low-temperature treatment. The suitable cultivation temperature for early-blooming P. mume cultivars was screened to provide a theoretical basis for further exploration of P. mume bonsai cultivation techniques. The results showed that the flowering rate, flower diameter, flowering quantity, flowering uniformity, and bud development in the 6℃ treatment were significantly better than those in the 10℃ treatment. The flowering rate and quality of different cultivars gradually increased with the accumulation of low-temperature. Therefore, chill accumulation plays a significant role in promoting flowering quality.

Abstract— In this paper, degradation effects such as the self-heating effect and the DIBL effect in 2D-MoS2-based MOSFETs are investigated through simulations. These are transistors with Al2O3 and HfO2 as the gate oxide and SiO2 and HfO2 as the back oxide (BOX). The self-heating effect (SHE) is simulated using the thermodynamic transport model. The dependence of the DIBL effect (Drain Induced Barrier Lowering) and the lattice temperature in the center of the channel on the gate length for transistors with different gate oxide and BOX materials is considered. Transistors are considered where the channel is fully and partially (just below the gate) covered by gate oxide. It is shown that the transistors with Al2O3 as gate oxide and SiO2 as BOX materials have higher immunity to DIBL effect and transistors with HfO2 as gate oxide and HfO2 as BOX materials have higher immunity to SHE.

(1) Background: This paper investigates the epidemiological risk related to temperature before and during COVID-19 in Italy; (2) Methods: Deaths in 2015-2019 and temperatures were correlated. Excess and COVID-19 deaths were examined to estimate the relationships with temperatures; (3) Results: Annual deaths were higher during the cold months (+45,000, SD = 4,700, S = 21). The scenario worsened during COVID-19. Mortality was higher during minimum temperature periods, although the curve moderately rose in the warmest months (r = -0.75, 95% CI = [-0.87; -0.56], S = 23). COVID-19 deaths showed a decreasing seasonality. Monthly excess deaths during COVID-19 were high (+4,200, IQR = [2,800; 8,000], S = 28) with a doubt of seasonality. COVID-19 mortality was correlated with regional latitude (r = 0.86, 95% CI = [0.68; 0.94], S = 20). Discrepancies between COVID-19 and excess deaths were found. The exposed population was subject to aging; (4) Conclusions: The epidemiological risk in Italy is seasonal and geographically dependent. Low and very high temperatures can lead to mortality peaks. Therefore, COVID-19 and any other epidemiological risk must be evaluated in light of this evidence. Health systems need to be strengthened during cold and extremely hot periods. Future research should investigate these phenomena at the causal level.

Lithium-ion batteries (LIBs) have become the preferred battery system for portable electronic devices and transportation equipment because of their high specific energy, good cycling performance, low self-discharge and no memory effect. However, too low ambient temperature will seriously affect the performance of LIBs, almost cannot discharge at -40~-60 ℃. There are many factors affecting the low temperature performance of LIBs, among which the electrode material is an important factor. Thus it is urgent to develop electrode materials or modify existing materials with excellent low temperature LIBs performance. Carbon-based anode is a kind of LIBs candidate. In recent years, it has been found that the diffusion coefficient of lithium ion in graphite anode decreases more obviously at low temperature, which is one of the important bottlenecks limiting its low temperature performance. However, the structure of amorphous carbon materials is complex, amorphous carbon materials have good ionic diffusion properties, and its grain size, specific surface area, layer spacing, structural defects, surface functional groups and doping elements may have a greater impact on the low temperature performance of the material. In this work, the low temperature performance of LIBs is obtained by modifying the carbon-based material from the perspective of electronic modulation and structural engineering.

Global warming has been increasing heat stress threat in animals which can be monitored by Temperature Humidity Index (THI). The present study describes the relationship of THI, calculated using 35 years period weather station data, and production performances of dairy cattle in a se-lected area of Bangladesh. The month January and June were identified as the coolest and hottest, respectively. Based on this outcome, every year in the month of January and June production performances of 10 crossbred cows with homogenous characteristics were monitored for a period of 5 years. The average THIMEAN value was found 17% higher in June as compared to January, and with this increment of THIMEAN average milk production was decreased 24.4% (p<0.05). The milk fat and protein content were also reduced (p<0.05) by 14.5 and 15.2%, respectively suggesting negative correlation as like as milk production. However, ash content was increased 15.3% that indicates a positive correlation. In addition, multiple regression analysis revealed each point increase in THIMEAN and rectal temperature, there was a decrease in milk yield 0.04 and 1.17 kg ECM, respectively. In contrary, each point increase in THIMEAN resulted 0.059 C increase of rectal temperature. Taken together, THIMEAN value calculated using metrological station data has distinct relationship with the production performances of lactating crossbred dairy cows.

Silver iodide (AgI) is a system prototype allowing the flow of ions through its structure and has a phase transition at 420 K, characterized by an abrupt change in conductivity and a high ionic conductivity. Introducing low concentrations of graphite (C) into the AgI structure produces a new material with a mixed conductivity (ionic and electronic) which increases with increasing temperature. The experimental results of the logarithm of the ionic conductivity as a function of the inverse of temperature for the (AgI)x–C(1−x) system for low carbon concentrations 0.97 ≤ x ≤ 0.99 were well fitted using a phenomenological model with a probability distribution for the charge carriers based on the carrier density

How to effectively suppress thermal cracks in the metal laser additive manufacturing process is still one of the key issues to be solved in the field of laser additive manufacturing. Metal tin, with wide liquid phase working temperature range, high boiling point, low viscosity, high thermal conductivity and excellent electrical conductivity. The use of tin as an auxiliary thermal management material in the metal additive manufacturing process is expected to achieve effective regulation of the temperature field and stress field of the formed part, thereby inhibiting the initiation of cracks and obtaining formed parts with the target grain structure and high reliability. This paper presented a novel liquid metal-assisted laser additive manufacturing method (LMAAM). A numerical model for the laser additive manufacturing of tin-assisted titanium alloys was established. The differences of the flow field, temperature field and stress field of the formed parts with tin and without tin were compared and analyzed. The influence of the interaction position between the tin liquid level and the forming part on the temperature field and stress field of the forming part was deeply studied. The laser additive manufacturing experiment of tin-assisted titanium alloy was carried out, and the experimental results were basically consistent with the simulation results, which verified the validity of the model. LMAAM technology has proven to be an effective method for additive manufacturing of highly reliable formed parts.

As one of the most promising ablative fillers, multi-walled carbon nanotubes (MWCNTs) have been used to improve the ablative resistance of Ethylene-Propylene-Diene Monomer (EPDM) insulators by facilitating the carbothermal reduction reaction of silica. However, the contribution of MWCNTs to char layer structure of the insulators was unclear. In this work, the effects of MWCNTs on char layer structure and ablative resistance were investigated in different EPDM-based insulators with and without silica. The results showed that adding only 3 phr MWCNTs can reduce the linear ablation rate of EPDM-based insulators without silica by 31.7%, while 6 phr MWCNTs are required to obtain similar results in EPDM-based insulators with silica. Both the char layer morphology of the two insulators gradually evolved into dense porous structure as MWCNTs content increasing, but their formation mechanisms are different. The XRD and Raman spectrum showed that different physicochemical reactions occurred around MWCNTs under different charring components. The proposed ablation mechanism was further verified by designing alternating multilayer distribution of MWCNTs and silica. This work can guide the construction of desirable char layer structure for increasing ablative resistance of EPDM-based insulators.

An increase in air temperature leads to a significant transformation of the relief and landscapes of the Arctic. The rate of permafrost degradation, posing a profound change in the Arctic landscape, depends on air temperature, vegetation cover, type of soils, surface and ground waters. The existing international circumpolar programs dedicated to monitoring the temperature state of permafrost TSP (Thermal State Permafrost) and active layer thickness CALM (Circumpolar Active Layer Monitoring) are not sufficient for a comprehensive characterization of geocryological conditions. Yet, no standardized protocol exists for permafrost monitoring and related processes. Here, we propose a novel multi-parameter monitoring protocol and implement for two sites in the European part of the Russian Arctic: the Yary site along the coast of the Baydaratskaya Bay in the Kara Sea (68.9°N) within the continuous permafrost area and the Hanovey site in the Komi Re-public (67.3°N) within the discontinuous permafrost one. The protocol includes drilling boreholes, determining the composition and properties (vegetation cover and soils), snow cover measure-ment, geophysical imaging, active layer estimation and continuous ground temperature meas-urements. Ground temperature measured in 2014 – 2020 revealed that amplitudes of surface tem-perature fluctuation had no significant difference between the Yary and Hanovey sites, while that the mean annual temperatures between the areas had a considerable difference of greater than 3.0 °C. The period of the presence of the active layer changed with the year (e.g., ranging between 135 and 174 days in the Yary site), showing longer when the air temperatures in summer and the preceding winter were higher. Electrical resistivity tomography (ERT) allowed determining the permafrost distribution and active layer thicknesses. Thermometry results were consistent with our geophysical data. Analyzing the composition and properties of frozen soils helped better interpret the data of geophysical and temperature measurements. Our work by integrating the study of the soil properties, ground temperatures, and ERT allowed fully characterize these sites, suggesting that it helps better understand the thermal state in any other research sites in the European north of Russia. Our suggested monitoring protocol enables calibrating and verifying the numerical and analytical models of the heat transfer through the earth’s surface.

The Laser Thermal-Joule Heating Composite Process was studied by orthogonal tests based on an analysis of fabrication parameters such as the laser power, wire feeding speed, and electric current. Temperature profiles and the geometric morphology of deposited layers under different process parameters were analyzed, and the overlaps between the layers and the substrate were observed. Results show that when the temperature at the bottom layer of the additive manufacturing is higher than the melting point of the substrate, and the highest temperature at the top layer does not exceed the over-firing temperature, good morphology and close bonding with the substrate can be obtained. Finally, appropriate process parameters were identified and verified to print multiple layers continuously.

Recently, it was reported that the physical cross-linking exhibited by some biopolymers could provide multiple benefits to biomedical applications. In particular, grafting thermoresponsive polymers onto biopolymers may enhance the degradability or offer other features, as ther-mothickening behavior. Thus, different interactions will affect the different hydrogen bonds and interactions from the physical cross-linking of CMC, the lower critical solution temperatures (LCSTs), and the presence of the ions. This work focuses on the study of blends composed of poly(N-isopropylacrylamide), poly(N-ethylacrylamide), and carboxymethyl cellulose in water and water/methanol. The molecular features, the thermoresponsive behavior, and gelation phenomena are deeply studied. The ratio defined by both homopolymers will alter the final properties and the gelation of the final structures, showing that the presence of the hydrophilic groups modifies the number and contributions of the diverse hydrogen bonds.

Magnetic sensors are widely used in health management systems for turbomachinery, but their applications in the hot zone are limited due to the loss of magnetic properties by permanent magnets with increasing temperature. The paper presents and verifies models and design solutions aimed at improving the performance of an inductive sensor for measuring the motion of rotating objects operating at elevated temperatures (200-1000C), such as compressor and turbine blades. Physical, analog and mathematical models of the interaction of blades with the sensor were developed. A prototype of the sensor was made and its tests were carried out on the RK-4 rotor rig for the speed of 7000 rpm, in which the temperature of the sensor head was gradually increased to 1100C. The sensor signal level was compared to that of an identical sensor operating at room temperature. The heated sensor works continuously producing the output signal whose level does not change significantly. What is more, a set of six probes passed an initial engine test in an SO-3 turbojet. It was confirmed that the proposed design of the inductive sensor is suitable for blade health monitoring of the last stages of compressors, steam turbines as well as previous generation gas turbines operating below 1000C, even without a dedicated cooling system. In real-engine applications, sensor performance will depend on how the sensor is installed and the available heat dissipation capability

While the ongoing climate change is well documented, the impacts exhibit a substantial variability, both in direction and magnitude, visible even at regional and local scales. However, the knowledge of regional impacts is crucial for the design of mitigation and adaptation measures, particularly when changes in the hydrological cycle are concerned. In this paper we present hydro-meteorological trends based on observations from a hydrological research basin in Eastern Austria between 1979-2019. The analysed state variables include the air temperature, the precipitation, and the catchment runoff. Additionally, trends for the catchment evapotranspiration were derived. The analysis shows that while the mean annual temperature was decreasing and annual temperature minima remained constant, the annual maxima were rising. The long-term trends indicate a shift of precipitation to the summer with minor variations observed for the remaining seasons and at an annual scale. Observed precipitation intensities mainly increased in spring and summer between 1979-2019. The catchment evapotranspiration, computed based on catchment precipitation and outflow, showed an increasing trend for the observed time period.

Lack of due attention to the orientation of streets and establishment of urban blocks without regard for climatic characteristics and conditions of the environment have an adverse effect on thermal comfort in open urban spaces. Construction of new settlements without taking into account climatic requirements undermines thermal comfort for pedestrians and other users, especially in cold regions. Considering the coldness of the region under study and the significance of the orientation of streets in absorbing radiation and providing heat to outdoor urban spaces, this study investigates the effect of the orientation of streets on microclimatic comfort in one of the residential towns of Hamadan City in Iran. For this purpose, microclimate simulation was performed using ENVI-met software. A residential block with four different orientations (the most common orientations of its surrounding buildings) were simulated in the coldest day of winter and the hottest day of summer. The results suggest that streets have different thermal behavior in different orientations. Orientation affects mean radiant temperature (Tmrt), the duration of exposure to direct sunlight, wind speed, and physiological equivalent temperature (PET), which are all important factors in thermal comfort. Based on these findings, north-south streets in Hamedan receive more radiant temperature during winter compared to other simulated orientations and provide more desirable thermal comfort. The average PET value on a winter day at a point on the north-south passage was 4.5-8 °C warmer than other orientations. In summer, streets with intercardinal orientations (i.e., northeast-southwest and northwest-southeast) provided the lowest PET (about 2 °C cooler than other orientations) and better thermal comfort

High temperature (HT) significantly affects the crop physiological traits and reduces the 12 productivity in plants. To increase yields as well as survival of crops under HT, developing heat13 tolerant plants is one of the main targets in crop breeding programs. The present study attempted 14 to investigate the linkage of the heat tolerance between the seedling and the reproductive growth 15 stages of tomato cultivars ’Dafnis‘ and ’Minichal’. This research was undertaken to evaluate heat 16 tolerance under two experimental designs such as screening at seedling stage and screening from 17 reproductive traits in greenhouses. Survival rate and physiological responses in seedlings of 18 tomatoes with 4-5 true leaf were estimated under HT (40 °C, RH 70%, day/night, respectively) and 19 under two control and HT greenhouse conditions (day time 28 °C and 40 °C, respectively). Heat 20 stress significantly affected physiological-chemical (photosynthesis, electrolyte conductivity, 21 proline) and vegetative parameters (plant height, shoot fresh weight, root fresh weight) in all 22 tomatoes seedlings. The finding revealed that regardless of tomato cultivars the photosynthesis, 23 chlorophyll, total proline and electrical conductivity parameters were varied in seedlings during the 24 heat stress period. The heat tolerance rate of tomatoes in the seedling stage might not be associated 25 always with reproductive parameters. HT reduced the fruit parameters likeas fruit weight (31.9%), 26 fruit length (14.1%), fruit diameter (19.1%) and fruit hardness (9.1%) in compared to NT under HT 27 in heat susceptible tomato cultivar ‘Dafnis’, while in heat tolerant cultivar ‘Minichal’ fruit length 28 (7.1%) and fruit diameter (12.1%) was decreased by the affect of HT but on the contrary fruit weight 29 (3.6%) and fruit hardness (8.3%) were increased. In conclusion, screening and selection for tomatoes 30 should be evaluated at the vegetative and reproductive stages with consideration of reproductive 31 parameters.

The energy transfer process of laser selective melting is very complex. To study the effect of la-ser selective melting on the microstructure and properties of 18Ni-300 martensitic steel, ABAQUS was used to simulate the temperature of laser cladding 18Ni-300 martensitic steel at different time points and different laser power. The results show that the cross-section shape of the molten pool changes from round to oval With the increase of laser power, the higher the peak value of temperature time curve, the greater the temperature gradient; and the laser clad-ding experiment of 18Ni-300 martensitic steel was carried out, and the microstructure and me-chanical properties of the samples under different laser power were analyzed. The results show that with the increase of laser power, the grain size of the cladding layer becomes smaller and the microstructure becomes more compact; the hardness of the side surface of the sample is higher than that of the upper surface, and the tensile strength and elongation show a trend of first increasing and then decreasing.

The use of different primary energy sources in human society has led to two major polluting emissions in the environment: energy (mostly heat), and chemical substances (mostly carbon dioxide). In this paper, the total global anthropogenic emissions of heat to the atmosphere during the industrial era (years 1850-2018) were determined and their effect on the change of global atmospheric temperature was calculated. The concept of a theoretical three-phase Earth reactor was introduced to estimate global atmospheric temperature increase caused by anthro-pogenic heat emissions. The resulting calculations closely approximated the actual atmospheric temperature change recorded during the last 170-year period. These results suggest that the temperature change of the atmosphere (global warming) is entirely due to anthropogenic heat emissions.

The efficacy of weed management depends on the correct control timing according to the seedling emergence dynamics. Since soil temperature and soil moisture are two main factors that determine weed germination, the hydrothermal time model can be used to predict their emergence. The aim of this study was to estimate the base temperature (Tb) and base water potential (Ψb) for germination of Chenopodium album, Amaranthus retroflexus, Setaria pumila and Panicum capillare collected from fields in continental Croatia and then to compare these values with those of Italian populations embedded in the AlertInf model. Germination tests were performed at seven constant temperatures (ranging from 4 to 27°C) and eight water potentials (0.00 to - 1.00 MPa). Estimated Tb and Ψb were 3.4°C, -1.38 MPa for C. album, 13.9°C, -0.36 MPa for A. retroflexus, 6.6°C, -0.71 MPa for S. pumila and 11.0°C, -0.87 MPa for P. capillare, respectively. According to the criterion of overlap of the 95% confidence intervals, only Tb of C. album, and Ψb of A. retroflexus were similar between Croatian and Italian populations. Further field experiments should be conducted in the Croatian field to monitor weed emergence patterns of C. album and to calibrate the AlerInf equation parameters.

When different strain hardening and strain rate sensitive materials are used for scaled model and prototype, the traditional pure geometrical similarity laws of solid mechanics will fail. Although correcting the basic scaling factors of velocity, density and geometry have been developed to compensate for the material distortion in recent non-geometric scaling works, it is difficult to be widely used because of its inherent indirect (depending on the structural strain and strain rate responses) and inexact (having significant prediction errors for prototype) defects. In this paper, a framework of material similarity, based on the new suggested material dimensionless numbers and the ‘Material number vs. strain/strain-rate’ function curves, are further developed, which represents the objective requirement of similarity theory for the basic mechanical properties of materials. It is demonstrated what is similitude materials of solid mechanics and how to use the best similitude materials to overcome the non-scalabilities of materials for identical or different materials. The direct and exact solution of the basic correction factors is further obtained and therefore overcomes the previous inherent indirect and inexact defects radically. Based on the similarity evaluation of different materials of the classical constitutive models, the impacted structures of circular plate and crooked plate with strain hardening and strain rate sensitive materials are verified numerically. The results show the completely different materials can be exact similitude for various structural behaviors (strain, strain rate, stress and displacement) of time and space fields after using the best similitude materials; and the basic correction factors do not depend on the structural strain and strain rate responses. As a contrast, when the non-similitude materials are used, the similarity results are very sensitive to the selection of strain/strain-rate and often leads to failed predictions. In addition, for the material elastic and temperature effects, the proposed method is also discussed to be valid.

It is common knowledge that increasing CO₂ concentration plays a major role in enhancement of the greenhouse effect and contributes to global warming. The purpose of this study is to complement the conventional and established theory that increased CO₂ concentration due to human emissions causes an increase of temperature, by considering the reverse causality. Since increased temperature causes an increase in CO₂ concentration, the relationship of atmospheric CO₂ and temperature may qualify as belonging to the category of “hen-or-egg” problems, where it is not always clear which of two interrelated events is the cause and which the effect. We examine the relationship of global temperature and atmospheric carbon dioxide concentration at the monthly time step, covering the time interval 1980–2019, in which reliable instrumental measurements are available. While both causality directions exist, the results of our study support the hypothesis that the dominant direction is T → CO₂. Changes in CO₂ follow changes in T by about six months on a monthly scale, or about one year on an annual scale. We attempt to interpret this mechanism by involving biochemical reactions, as at higher temperatures soil respiration, and hence CO₂ emission, are increasing.

The narrow process window during intercritical annealing and discontinuous yielding have limited the commercialisation of medium Mn steels. In this study, a double annealing process based on the commercial continuous annealing line is proposed. The cold-rolled medium Mn steels were first fully austenitized and quenched during the first annealing, followed by the intercritical annealing for reverted austenite transformation. The microstructure of duplex lath-shaped austenite and ferrite is produced and the steel exhibit a desirable continuous yielding during tensile deformation. Al is added into the medium Mn steel to enlarge the process window and to improve partitioning efficiency of Mn. The produced steel is more robust with temperature fluctuation during the industrial process due to the enlarged intercritical region. Mn partitioning is more efficient owing to elevated annealing temperature, which results in the improvement of ductility in the Al-added steel with increased austenite stability.

We investigated the characteristics of surface wind speeds and temperatures predicted by the local data assimilation and prediction system (LDAPS) operated by the Korean Meteorological Administration. First, we classified automated weather stations (AWSs) into four categories [urban flat (Uf), rural flat (Rf), rural mountainous (Rm), and rural coastal (Rc) terrains] based on the surrounding land cover and topography, and selected 25 AWSs representing each category. Then we calculated the mean bias error of wind speed (WE) and temperature (TE) using AWS observations and LDAPS predictions for the 25 AWSs in each category for a period of 1 year (January–December 2015). We found that LDAPS overestimated wind speed (average WE = 1.26 m s–1) and underestimated temperature (average TE = –0.63°C) at Uf AWSs located on flat terrain in urban areas because it failed to reflect the drag and local heating caused by buildings. At Rf, located on flat terrain in rural areas, LDAPS showed the best performance in predicting surface wind speed and temperature (average WE = 0.42 m s–1, average TE = 0.12°C). In mountainous rural terrain (Rm), WE and TE were strongly correlated with differences between LDAPS and actual altitude. LDAPS underestimated (overestimated) wind speed (temperature) for LDAPS altitudes that were lower than actual altitude, and vice versa. In rural coastal terrain (Rc), LDAPS temperature predictions depended on whether the grid was on land or sea, whereas wind speed did not depend on grid location. LDAPS underestimated temperature at grid points on the sea, with smaller TE obtained for grid points on sea than on land.

Ti-6Al-4V (TC4) titanium alloy parts were successfully fabricated by laser melting deposition (LMD)technology in this study. Proper normalizing temperatures were presented in detailed for bulk LMD specimens. Optical microscope, scanning electron microscopy, X-ray diffraction and electronic universal testing machine were used to characterize the microstructures, phase compositions, the tensile properties and hardness of the TC4 alloy parts treated using different normalizing temperature. The experimental results showed that the as-fabricated LMD speceimens microstructures mainly consisted of α-Ti phase with a small amount of β-Ti phase. After normalizing treatment, in the area of α-Ti phase, the recrystallized length and width of α-Ti phase both increased. When normalizing in the (α+β) phase field, the elongated primary α-Ti phase in the as-deposited state was truncated due to the precipitation of β-Ti phase and became a short rod-like primary α-Ti phase. In as-fabricated microstructure, the β-Ti phase was precipitated between different short rod-shaped α-Ti phases distributed as basketweave. After normalizing treatment at 990 for two hours with subsequent air cooling, the TC4 titanium alloy had significant different microstructures from original sample produced by LMD. Moreover, the mismatch of tensile and hardness property was mitigated in this heat treatment. So the normalizing treatment methods and temperature can be qualified as a prospective heat treatment of titanium alloy fabricating by laser melting deposition.

The physical environment plays an important role in the transmission of respiratory infections like Covid-19. To find relevant articles on environmental factors influencing respiratory infection outbreaks, we searched Pub med Central on the following topics: 1. Environmental pollution causing coronavirus fatality- 73 results, relevant 1 article, 2. Environmental factors affecting Covid-19, 149 results from which there were 6 relevant articles, 3. Impact of air pollution on Covid-19 fatality, 10 results, relevant 3 articles, 4. Environmental factors affecting respiratory viruses- 10646 results were obtained, 2 relevant articles. We searched Google scholar on environmental factors affecting Covid-19 transmission and found 7 relevant papers. We excluded the duplicates in each of the key words search. Date of search was on 20^th April 2020. All articles included in results were scrutinized and relevance of articles was based on their content that discussed meteorological and physical environment factors in the spread and severity of Covid-19. We have discussed factors like air pollution, smoking, air temperature, humidity and air velocity as contributing factors. If meteorological factors are conducive to spread in a particular area, we need protective measures way before a respiratory infection outbreak occurs. Covid-19 is a lesson learnt the hard way, and we must enable people to practice hygienic practices with limited resources but high level of protection that it provides. Air pollution control can prevent priming of respiratory system which shall further protect from pulmonary infections.

Estimating heat emission losses of heating systems is an important task of energy efficiency assessments in buildings. To this aim, the present international standards contain tabulated values for different emitter and control system configurations, without however explaining how to compute the effect of increased setpoint temperatures on the system losses. Moreover, the effects of each component are treated as independent, while e.g. vertical stratification and temperature control of the system are cross-related. In this paper we attempt to fill this gap by proposing a calculation method to calculate the product category specific setpoint variations for space heating emitters, accounting for the overall heat balance in the enclosure and including the cross-correlations of each component as well. The emission losses of a heating system are computed using a temperature setpoint variation method that is imposed on annual energy calculations. This complements the procedure presented in the Standard EN15316-2, also providing the possibility to use product-specific values of setpoint variations instead of tabulated values. As the main finding of the study, the calculation process is defined for a European Reference Room, namely for a specific enclosure that allows an accurate and transparent evaluation of the total setpoint variation. The product-specific values of setpoint variations are calculated from measured vertical stratification and control parameters with an annual simulation model of the European Reference Room. The total setpoint variations were simulated for a set of heat emitters and controllers in order to quantify and compare the energy performance of a new and an old type building located in Strasbourg. We find that the total setpoint variation required to overcome emission losses is up to 2.00 °C in the old building and 1.20 °C in the new building, corresponding respectively to an increase in total heating energy usage of up to 22% and 20%.

The improvement of the methane combustion activity was observed in cyclic temperature-programmed and isothermal reactions over Pd/ZrO2 catalysts by simple reduction/re-oxidation treatment. The catalytic activity increased during the initial stages of isothermal reaction, and the light-off temperature was lowered as the number of cycles increased in the cyclic temperature-programmed reaction. To reveal the origin of activation, variations in the reduction properties after the activation period were carefully investigated through CH4 temperature-programmed reduction (TPR) measurements. From the CH4-TPR results, it was confirmed that the reduction temperature decreased significantly after activation. The observation of the CH4-TPR peak at relatively low temperatures is directly proportional to the catalytic activity of CH4 combustion. It was therefore concluded that repeated reduction/re-oxidation occurred in the reactant stream, and this phenomenon allowed the combustion reaction to proceed more easily at lower temperatures.

Dengue hemorrhagic fever is an arboviral infectious disease that has occurred frequently as an extraordinary event due to its fast spread and lethal potential in Indonesia. The vector Aedes aegypti is sensitive to climate variability. This study determines the relationship between climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia from 2009 to 2017. This study used the monthly dengue hemorrhagic fever incidence obtained from the Surabaya Health Office and the monthly climate variability parameters (average temperature, rainfall, humidity) obtained from the Indonesian Agency for Meteorology, Climatology and Geophysics and website www.worldweatheronline.com. Data analysis was done using One-Sample Kolmogorov Smirnov Test and Spearman non-parametric correlation test. The results showed a correlation between all three climate variability parameters with dengue hemorrhagic fever incidence (average temperature p<0.05, r=-0.603; rainfall p<0.05, r=0.407; humidity p<0.05, r=0.7). Average temperature is negatively correlated to dengue hemorrhagic fever incidence, while rainfall and humidity are positively correlated to dengue hemorrhagic fever incidence. This study shows preliminary evidence on the correlation of climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia.

The water-rich liquid layer immobilized on the surface of the polar stationary phases is critical to the retention of polar compounds in hydrophilic interaction chromatography (HILIC). Although the presence of the adsorbed water layer has been investigated and confirmed by multiple techniques, there is a lack of quantitative measure that can be easily determined and linked to chromatographic parameters. This study proposes a simple measure termed volume ratio (the ratio of the adsorbed water layer volume and the mobile phase volume) that provides a relative, but quantitative information on the adsorbed water layer and may be linked to the phase ratio. The volume ratio can be easily determined using toluene elution volume. The volume ratio values are measured in 25 polar stationary phases in various mobile phase conditions. In addition to the acetonitrile content in the mobile phase, ammonium acetate concentration in the mobile phase and column temperature also have significant influences on the volume ratio and the adsorbed water layer.

There is increasing use of wood-based composites in industry not only because of the shortage of solid wood, but above all for their better properties such as: strength, aesthetic appearance, etc. compared to wood. Medium density fibreboard (MDF) is a wood-based composite that is widely used in the furniture industry. The goal of the research conducted was to determine the effect of the type of coating on the drill cutting blades on the value of thrust force (F_t), cutting torque (M_c), cutting tool temperature (T) and surface roughness of the hole in drilling MDF panels. In the tests three types of carbide drills (HW) were used: not coated, TiAlN coated and ZrN coated. The measurement of both the thrust force and the cutting torque was carried out using an industrial piezoelectric sensor. The temperature of the cutting tool in the drilling process was measured using an industrial temperature measurement system using a K-type thermocouple. It was found that the value of the maximum temperature of the tool in the drilling process depends not only on the cutting speed and feed rate, but also on the type of coating of the cutting tool. The value of both the cutting torque and the thrust force is significantly influenced by the value of the feed rate and the type of drill coating. The effect of varying plate density on the surface roughness of the hole and the variation of the value of the thrust force is also discussed. The results of the investigations were statistically analysed using a multi-factorial analysis of variance (ANOVA).

Dengue hemorrhagic fever is an arboviral infectious disease that has occurred frequently as an extraordinary event due to its fast spread and lethal potential in Indonesia. The vector Aedes aegypti is sensitive to climate variability. This study determines the relationship between climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia from 2009 to 2017. This study used the monthly dengue hemorrhagic fever incidence obtained from the Surabaya Health Office and the monthly climate variability parameters (average temperature, rainfall, humidity) obtained from the Indonesian Agency for Meteorology, Climatology and Geophysics and website www.worldweatheronline.com. Data analysis was done using One-Sample Kolmogorov Smirnov Test and Spearman non-parametric correlation test. The results showed a correlation between all three climate variability parameters with dengue hemorrhagic fever incidence (average temperature p<0.05, r=-0.603; rainfall p<0.05, r=0.407; humidity p<0.05, r=0.7). Average temperature is negatively correlated to dengue hemorrhagic fever incidence, while rainfall and humidity are positively correlated to dengue hemorrhagic fever incidence. This study shows preliminary evidence on the correlation of climate variability and dengue hemorrhagic fever in Surabaya, East Java, Indonesia.

This study presents a novel approach for the early detection of developing thunderstorms. To date, methods for the detection of developing thunderstorms usually rely on accurate atmospheric motion vectors (AMVs) for the estimation of cooling rate of convective clouds, which corresponds to the updraft strength of the cloud objects. In this study we present a method for the estimation of the updraft strength that does not rely on AMVs. The updraft strength is derived directly from the satellite observations in the SEVIRI water vapor channels. For this purpose the absolute value of the vector product of two vectors derived from the observed radiances emitted by the water vapor channels in 2 subsequent satellite images is calculated. The x and y components of the vectors consists of the temporal change of the spatial brightness temperature gradients in x- and y-direction, the z component consists of the temporal variation of the brightness temperature at pixel level. The absolute value of the vector product is referred to as normalized updraft strength (NUS). The performance of the method has been investigated for 2 summer periods in 2016 and 2017 by validation with lightning data. Values of the Critical Success Index (CSI) of about 66 % for the 2016 period and 62 % for the 2017 period demonstrate the good performance of the method. The POD values for the experiments with the highest CSI values are 90.3 for 2016 period and 87.6 for the 2017 period, respectively The corresponding FAR values are 28.2% (2016) and 32.5 % (2017), respectively. In summary, the method has the potential to reduce the forecast lead time significantly, and can be quite useful in regions without a well maintained radar network.

The relationship between city size, coastal land use and air temperature rise with distance from coast during summer day is analyzed using the meso-scale Weather Research & Forecasting (WRF) model in five coastal cities in Japan with different sizes and coastal land use (Tokyo, Osaka, Nagoya, Hiroshima and Sendai) and inland cities in Germany (Berlin, Essen and Karlsruhe). Air temperature increased as distance from the coast increased, reached its maximum, and then decreased slightly. In Nagoya and Sendai, the number of urban land use in coastal areas is less than the other three cities, where air temperature is a little lower. As a result, air temperature difference between coastal and inland urban area is small and the curve of air temperature rise is smaller than those in Tokyo and Osaka. In Sendai, air temperature in the inland urban area is the same as in the other cities, but air temperature in the coastal urban area is a little lower than the other cities, due to about one degree lower sea surface temperature influenced by the latitude. In three German cities, the urban boundary layer may not develop sufficiently because the fetch distance is not enough.

Recently Kawashima has reported that, when wetted with alkanes, several forms of graphite and single-layer graphene exhibit superconductor-like properties above room temperature under ambient pressure [AIP Adv. 2013, 3, 052132; arXiv:1612.05294; arXiv:1801.09376]. Under the assumption that these seemingly unlikely properties arise from the presence of paired electrons brought about by the alkane-wetting, we explored their implications to arrive at a probable mechanism for strong electron-pairing driven by Fermi surface nesting and acoustic phonon. This mechanism explains why alkane-wetting is essential for the graphene systems to become “superconductor-like” above room temperature and why the “T_c” of alkane-wetted pitch-based graphite fibers increases almost linearly from ~363 to ~504 K with increasing the molecular weight of alkane from heptane to hexadecane. It also provides a number of experimentally-verifiable predictions, the confirmation of which will provide a strong support for the superconductivity driven by Fermi surface nesting and acoustic phonon.

Different process parameters can alter the temperature during machining. Consequently, selecting process parameters that lead to a desirable cutting temperature would help to increase the tool life, decrease the tensile residual stress, and controls the microstructure evolution of the workpiece. An inverse computational methodology is proposed to design the process parameters for specific cutting temperature. A physics-based analytical model is used to predict the temperature induced by cutting forces. To calculate the temperature induced by the deformation in the shear zone, a moving point heat source approach is used. The shear deformation and chip formation model is implemented to calculate machining forces as functions of process parameters, material properties, and etc. The proposed model uses the analytical model to predict the cutting temperatures and applies a variance-based recursive method to guide the inverse analysis. In order to achieve the cutting process parameters, an iterative gradient search is used to adaptively approach the specific temperature by the optimization of process parameters such that an inverse reasoning can be achieved. Experimental data are used to illustrate the implementation and validate the viability of the computational methodology.

Metal-Organic Frameworks (MOFs) are a subclass of porous materials that have unique properties such as varieties of structures from different metals and organic linkers, tunable porosity from a structure or framework design, etc. Moreover, modification/functionalization of the material structure could optimize the material properties and demonstrate high potential for a selected application. MOF materials exhibit exceptional properties and make these materials widely applicable including in energy storage and heat transformation applications. This review aims to give a broad overview of MOFs and their development as adsorbent materials having the potential for heat transformation applications. We summarize current investigations, developments, and possibilities of metal-organic frameworks (MOFs) especially the tuning of the porosity and hydrophobic/hydrophilic design required for this specific application. These materials applied as adsorbent are promising in the thermal driven adsorption for heat transformation using water as working fluid and related application.

The accurate quantification of $\frac{F{e}^{3+}}{\Sigma Fe}$ ratios for Mössbauer spectroscopic room temperature measurements involves many steps and, when shown in a composite Mössbaur data table, does not allow enough space for more Mössbauer parameters to be presented in the composite table. So a simple formula is derived, (presented as a short communication) which users will find helpful when they have to determine corrected $\frac{F{e}^{3+}}{\Sigma Fe}$ ratios in their room temperature Mössbauer experiments.

The welding performance of shipbuilding steel under large heat input could be improved greatly by the Mg addition to the steel, but the impact toughness of the HAZ is not stable. According to the three different thickness steel plates obtained in the industrial experiment, the large heat input welding was carried out by different heat input, and the impact toughness analysis, impact fracture analysis, metallographic microstructure analysis and inclusions analysis were carried out. The results showed that, the HAZ of three kinds of thickness plates induced a lot of IAF, with Mg addition, the inclusion dimension had been reduced effectively, and the IAF induced ability of the inclusions had also been improved. The difference of HAZ impact toughness with different welding heat input and different impact temperature is significant, in consideration of the influence of welding heat input and metallographic microstructure on impact toughness of HAZ, the welding heat load had far greater effect than metallographic microstructure on ductile-brittle transition temperature. At the same time, if the original metallographic microstructure of steel was coarse, the pinning effect of the inclusions would be reduced significantly, and the microstructure of HAZ would be coarsened and the impact toughness of HAZ would be decreased, so there is a certain matching relationship between the metallographic microstructure and the inclusion dimension.

Despite the ecological importance of forest tree species, our study was motivated by scarce data on dendrochronology studies limited to the northwestern part of Tajikistan due to lack of access to such a part of the country which is difficult to access. Current studies on Junipers in the northwestern part of Tajikistan identified that tree ring-based climate reconstruction is possible. Cores of Juniperus Turkestanica from Taboshar area, Sogd province were developed into 176-year tree-ring width chronology. In the current study a summer (June-September) minimum temperature reconstruction spanning AD 1840–2016 was developed, which can explain 30.0% of the instrumental variableness for the period of 1940–2015. Five warmest (1856–1866, 1869–1871, 1907–1916, 1923–1935, 1988–2016) and four coldest time periods (1840–1855, 1872–1906, 1917–1922, 1940–1984) were identified. The developed reconstruction coincides with cold and warm periods with prior investigations from tree-rings in China, Mongolia, Kyrgyzstan, Kazakhstan and Tajikistan. Spatial correlation analysis with the gridded minimum temperature data shows that the temperature reconstruction covers geographical representation over High Asia. Significant correlation was found between temperature reconstruction with summer SST, which suggests strong linkages of regional temperature variability with Indian-Ocean climate system. The obtained spectral peaks from the spectral analysis of the summer temperature reconstruction were significantly at 84.7-year (90%), 2.9-year (99%), 2.6-year (99%), 2.5-year (99%), 2.4-year (99%) and 2.2-year (99%).

The effect of the acetylene and hydrogen gases mixture ratios in direct low-temperature vacuum carburization was investigated. The gas ratio is an important parameter for producing the free radicals in the carburization. The free radicals can remove the natural oxide film by the strong reaction of the hydrocarbons, and then thermodynamically activity can be increased. When the gas ratio was below 1, the supersaturation expanded austenite layers were formed on the surface of the AISI 316L stainless steel, which had the maximum carbon solubility up to 11.5 at.% at 743 K, were formed. On the other hand, when the gas ratio was above 1, the carbon concentration of them remained low even if the process time was enough increased to reach the maximum carbon solubility. As a result, the carbon concentration underneath the surface was determined to be highly dependent on the gas mixture ratio of acetylene and hydrogen. In conclusion, it is necessary to restrict the ratio of acetylene and hydrogen gases to total mixture gases to form the expanded austenite layer with the high carbon concentration in the direct low-temperature vacuum carburization.

This paper consists of the design and implementation of a simple conditioning circuit to optimize the electronic nose performance, where a temperature modulation method was applied to the heating resistor to study the sensor’s response and confirm whether they are able to make the discrimination when exposed to different volatile organic compounds (VOC’s). This study was based on determining the efficiency of the gas sensors with the aim to perform an electronic nose, improving the sensitivity, selectivity and repeatability of the measuring system, selecting the type of modulation (e.g., pulse width modulation) for the analytes detection (i.e., Moscatel wine samples (2% of alcohol) and ethyl alcohol (70%)). The results demonstrated that by using temperature modulation technique to the heating resistors, it is possible to realize the discrimination of VOC’s in fast and easy way through a chemical sensors array. Therefore, a discrimination model based on principal component analysis (PCA) was implemented to each sensor, with data responses obtaining a variance of 94.5% and accuracy of 100%.

This paper proposes a novel method for optimizing the Cauer-type thermal network model considering both the temperature influence on the extraction of parameters and the errors caused by the physical structure. In terms of prediction of the transient junction temperature and the steady-state junction temperature, the parameters of conventional Cauer-type are modified, and the general method for estimating junction temperature is studied by using the adaptive thermal network model. The results show that junction temperature estimated by adaptive Cauer-type thermal network model is more accurate than that of the conventional model.

The creep behaviors of TA2 and R60702 at low and intermediate temperature were presented and discussed in this paper. Experimental results indicated that an apparent threshold stress exhibited in the creep deformation of R60702. Meanwhile, the primary creep phase was found as the main pattern in the room temperature creep behavior of TA2. Compared with exponential law, the power law has been proved to be a proper constitutive model in the description of primary creep phase. It also showed that θ projection method had its significant advantage in the evaluation of accelerated creep stage. Thus, a composite model which combined power law with θ projection method was applied in the creep curves evaluation at low and intermediate temperature. Based on the multiaxial creep deformation results, the model was modified and discussed. A linear relationship existed between composite model parameters and applied load. Finally, the creep life could be accurately predicted and the composite model method is suitable for application in low and intermediate temperature creep life analysis.

This paper introduces a new destriping algorithm for remote sensing data. The method is based on combined Haar Stationary Wavelet transform and Fourier filtering. State-of-the-Art methods based on the discrete wavelet transform (DWT) may not always be effective and may cause different artifacts. Our contribution is three-fold: i) we propose to use the Undecimated Wavelet transform (UWT) to avoid as much as possible shortcomings of the classical DWT; ii) we combine a spectral filtering and UWT using the simplest possible wavelet, the Haar basis, for a computational efficiency; iii) we handle 2D fields with missing data, as commonly observed in ocean remote sensing data due to atmospheric conditions (e.g., cloud contamination). The performances of the proposed filter are tested and validated on the suppression of horizontal strip artifacts in cloudy L2 Sea Surface Temperature (SST) and ocean color snapshots.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r&gt;0.90) and peri-urban (HWM, HWA, r&gt;0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

In the present study we examine the relationship among sovereign yields, temperature and precipitation using a large monthly panel data set which consists of 20 eurozone members, over the period 1980M1 – 2023M4. To account for possible asymmetries along the distribution of the climate variables we assume a quadratic modelling specification and apply various mean panel estimation techniques of heterogeneous coefficients. At a next step, to consider possible nonlinearities in the distribution of the dependent variable (sovereign yields), we apply the quantile via moments methodology of Machado and Santos Silva (2019), which accounts for possible cross-sectional dependence and slope heterogeneity. We contribute to the existing literature in two main ways. First, by applying a quantile methodology that provides a more in-depth analysis of the climate effects along the distribution of the sovereign yields, especially in the presence of non-normally distributed data. Second, we find that climate change, as proxied by higher temperatures or lower precipitation (drought), will increase the sovereign risk of all countries, but the magnitude of the impact will be higher for countries that are already characterized by higher sovereign risk levels and/or face extreme weather conditions (hotter countries and/or countries with low levels of precipitation).

The surface velocity of the Amery Ice Shelf (AIS) is vital to assessing its stability and mass balance. Previous studies have shown that the AIS basin has a stable multi-year average surface velocity. However, spatiotemporal variations in the surface velocity of the AIS and the underlying physical mechanism remain poorly understood. This study combined offset tracking and DInSAR methods to extract the monthly average surface velocity of the AIS and obtained the inter-annual surface velocity from the ITS_LIVE product. An uneven spatial distribution in inter-annual variation of the surface velocity was observed between 2000–2022, although the magnitude of variation was small at less than 20.5 m/yr. The increase and decrease in surface velocity on the eastern and western-central sides of the AIS, respectively, could be attributed to the change in the thickness of the AIS. There was clear seasonal variation in monthly average surface velocity at the eastern side of the AIS between 2017–2021, which could be attributed to variations in the area and thickness of fast-ice and also to variations in ocean temperature. This study suggested that changes in fast-ice and ocean temperature are the main factors driving spatiotemporal variation in the surface velocity of the AIS.

Nonlocal theories are gaining prominence because they can solve problems which lead to unphysical conclusions in standard models. This study presents a novel fractional boundary element method (BEM) solution for nonlinear nonlocal thermoelastic problems of anisotropic fibrous polymer nanomaterials. This broad BEM solution combines two solutions: anisotropic fibrous polymer nanomaterials problem solution and nonlinear nonlocal thermoelasticity problem solution. The nonlinear nonlocal thermoelasticity problem solution divides the displacement field into complementary component and particular component. The overall displacement is generated using the boundary element technique, which is the solution to a Navier type problem, while the particular displacement is derived using local radial point. The New Modified Shift-Splitting (NMSS) approach, which reduces memory and processing time requirements, was used to solve linear systems created by BEM. Figures demonstrate the numerical findings, which show the effects of fractional and graded parameters on the thermal stresses of nonlinear nonlocal thermoelastic problems of anisotropic fibrous polymer nanomaterials. The numerical results indicate the consistency and efficiency of the proposed methodology.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (&gt;70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

Abstract: The YF3: (Eu3+, Nd3+) nanoparticles (orthorhombic phase, D ~ 130 nm)) were synthesized via the co-precipitation method with subsequent hydrothermal treatment and annealing. The Eu3+ τdecay linearly descends with the increase of temperature in the 80 - 320 K range. The τdecay (T) slope values of the annealed YF3: Eu3+ (2.5 and 5.0 mol. %) nanoparticles were the highest (110·10-4 and 67·10-4, μs/K in the whole 80 – 320 K range, respectively. Thus, these samples were chosen for further doping with Nd3+. The maximum Sa and Sr values based on the LIR (IEu/INd) function were 0.67 K-1 (at 80 K) and 0.86 %·K-1 (at 154 K), respectively. As it was mentioned above, the sin-gle-doped YF3: Eu3+ (2.5. %) nanoparticles showed the linearly decreasing τdecay (T) function (5D0 – 7F1 emission). The main idea of Nd3+ co-doping was to increase this slope value (as well as the sensitivity) by increasing the rate of τdecay (T) descent via the addition of one more tempera-ture-dependent channel of 5D0 excited state depopulation. Indeed, we managed to increase the slope (Sa) up to 180·10-4 K-1 at 80 K. This result is one of the highest compared to the world analogs.

Color centers in diamond and nanodiamonds can be utilized as quantum sensors for measuring various physical parameters, particularly magnetic and electric fields, as well as temperature. Due to its small size and possible surface functionalization, fluorescent nanodiamonds are attractive systems for biological and medical applications since they can be used for intracellular experiments. This review focuses on fluorescent nanodiamonds for thermometry with nanoscale spatial resolution for living systems. The current state of the art, possible further development, and potential limitations will be discussed here.

Heavy rains have created significant threats to human health and life. Floods and other natural disasters, which have a global impact annually, can be attributed to extended durations of intense precipitation. Accurate rainfall predictions are crucial in nations such as Bangladesh, where agriculture is the predominant occupation. The efficiency of machine learning (ML) methods is enhanced by the non-linearity of rainfall, surpassing the effectiveness of other alternative ways. Machine learning techniques show that individual classifiers exhibit worse accuracy than ensemble learning (EL) methodologies. Ensemble Learning techniques are utilized for rainfall prediction and estimating rainfall quantity and daily average temperature to enhance comprehension of the diverse Machine Learning algorithms. This research implements the machine learning techniques and ensemble-based classifier to predict the rainfall occurrence, along with the machine learning regressor models and ensemble-based regressor for the rainfall amount prediction and daily average temperature prediction, using Bangladesh Weather Dataset. The results of the machine learning and ensemble-based models are compared using the Accuracy and F1 score for rainfall occurrence prediction. In contrast, MAE and RMSE evaluation metrics are used for ensemble regressor and regression algorithms for the rainfall amount and daily average temperature prediction. With an accuracy of 83.41% and a recall of 78.17%, the Ensemble Classifier is the best at predicting when it will rain, but its precision of 51.16% stands in for the lowest. The Ensemble Regression model outperforms Linear Regression, Random Forest, and SVR in rainfall amount prediction, with the lowest MAE of 0.36 and RMSE of 0.90. The Ensemble Regression provides the most precise results for daily average temperature prediction with the lowest MAE 0.42 and RMSE 0.54 highlighting its superiority over the other regression models in forecasting temperature with less error. Ensemble approaches consistently lead task performance metrics.

Ralstonia solanacearum is the pathogen responsible for Ralstonia solanacearum, which is soil-borne, infests plant conduits to cause disease.They are not easy to control and are harmful.Therefore the development of a controlled-release agent responsive to the pathogen's soil temperature and moisture conditions could aid in its control. Corn kernel powder is used as a carrier for Tetramycin biopesticide, with various compounds tested for bonding.They were then made by extrusion moulding.Temperature and wetness responsive components, including Pentaerythritol Tetrastearate, Pentaerythritol Tetraoleate, Polyethylene Glycol Stearate, and Polyethylene Glycol Monooleate,are compounded and coated onto Tetramycin cores to form an intermediate shell layer. Finally, Ethyl cellulose(EC)and Hydroxypropyl methyl cellulose(HPMC) are dissolved and sprayed onto the outermost layer to complete the pellet's shell layer.After the evaluation of texture performance test,DSC analysis,TG test,temperature and humidity response performance test, as well as pellet cross-section SEM observation, field effectiveness test, etc., the preferred formulations were screened.The results showed that the preferred Core formulation:Corn kernel powder:Tetramycin aqueous:Xanthan gum mass ratio=13.5:23:2; Intermediate Shell layer:PETS: PETO: PEG400MO mass ratio=10:30:10; and Outer Shell layer: Ethyl cellulose (EC):Hydroxypropyl methyl cellulose (HPMC) mass ratio=5:1.Under soil conditions of high incidence of Ralstonia solanacearum, i.e., sustained warmth (30-35℃) and high humidity (30% moisture content), the formulated pills showed a release rate of 95.18% to 96.24% over a period of 35 days. Moreover, they showed a stepwise cyclic release process under alternating warm and humid-dry and cold conditions.In field tests on tobacco, a relative preventive efficacy of 54.74% was achieved 106 days post-transplanting. Soil bacterial community structure analysis revealed a significant decrease (2.28-2.84 times) in the abundance of Solanaceae Raelia under Tetramycin pellet treatment compared to the control. Additionally, fungal community structure showed highter consistency initially across various soil depths, with diversity differences between soil layers reestablished later (106 days), while the predominant categories of bacteria and fungi remained unchanged.In this study, we successfully developed a nucleoshell-type slow-controlled release pill embedded with Tetramycin. This pill effectively responded to temperature and humidity changes, resulting in high efficacy in disease prevention.This development holds significant promise for effectively improving drug utilization and easing application challenges, offering broad prospects for Ralstonia solanacearum prevention and control in agriculture.

UV-digital printing belongs to the commonly used method for custom large-area substrate decoration. Despite low surface energy and adhesion, transparent polymer materials, such as polymethylmethacrylate (PMMA) and polycarbonate (PC), represent an ideal substrate for such purposes. The diffuse coplanar surface barrier discharge (DCSBD) in a novel compact configuration was used for substrate activation to improve ink adhesion to the polymer surface. This industrially applicable version of DCSBD was prepared, tested, and successfully implemented for the UV-digital printing process. Furthermore, wettability and surface free energy measurement, X-ray photoelectron spectroscopy, atomic force and scanning electron microscopy evaluated the surface chemistry and morphology changes. The changes in adhesion of the surface and of ink were analyzed by a peel-force and a crosscut test, respectively. A short plasma treatment (1-5 s) enhanced the substrate's properties of PMMA and PC while providing the pre-treatment suitable for further in-line UV-digital printing. Furthermore, we did not observe damage or significant change of roughness affecting the substrate's initial transparency.

Coral reefs are one of the most productive yet vulnerable ecosystems on Earth. An important step in understanding the functioning of coral communities is studying the environmental impact on the state of reefs. The present study aimed to assess the impacts of the water temperature, precipitation, wave action and population density on the seasonal bleaching, partial and complete mortality of shallow-water branching corals of Pocillopora verrucosa species complex. The present study was conducted at the Dam Bay research station (Nha Trang Bay) from 26 April 2020 to 2 April 2021. Throughout the study the percentage of bleached coral colonies varied from 1 to 41.5% with two peaks, in autumn (October) and spring (April). Rates of the development of partial mortality varied from 0 to 10%, with a pronounced peak in December. At the end of the experiment, the percentage of coral colonies suffering from partial mortality reached 47%. Only 4,5% of experimental colonies died by the end of the study. Analysis revealed that water temperature and partial mortality are the drivers of bleaching, while wave action, temperature and bleaching are the factors with a significant impact on partial mortality. In the present study, the main cause of coral death was the development of algal fouling at the sites of colony lesions, which gradually spread over the entire surface of the colony. We showed also that the impact of individual stress on mortality prevailed over the impact of seasonal bleaching and partial mortality events.

Abstract: In the past years, lithium-ion solid-state batteries demonstrated significant advancements regarding such properties as safety, long-term endurance, and energy density. The properties of these depend on solid-state electrolytes and especially ionic transport interfacial transport with cathode or anode materials. Solid-state electrolytes based on lithium halides offer new opportunities due to their unique features such as broad electrochemical stability window, high lithium-ion conductivity, and elasticity at close to melting point temperatures that help to improve lithium-ion transport at interfaces. A comparative study of lithium indium halide (Li3InCl6) electrolytes syn-thesized by a mechano-thermal method using different optimization parameters revealed a signif-icant effect of ball-milling time, temperature, and pressure on lithium-ion transport. Based on the Electrochemical Impedance Spectroscopy (EIS) data in the temperature range of 25-100 °C, the optimized Li3InCl6 electrolyte phase demonstrates high ionic conductivity reaching 0.98 mS cm−1 at room temperature. However, at 70 °C, phase transformation was observed leading to significant changes in the activation energy for lithium-ion transport. In-situ X-ray diffraction and in-situ/operando X-ray photoelectron spectroscopy techniques confirmed the tempera-ture-dependent behavior of Li3InCl6 synthesized. These observations provide critical information for practical applications of solid-state electrolytes and nanocomposites based on Li3InCl6 within the broad temperature range for lithium-ion solid-state batteries with improved morphology, chemical interactions, and structural integrity.

The effects of rare earth Y content on the microstructure and high-temperature oxidation properties of 47Fe-36Ni-15Cr-1.5Mn alloy at 1000°C were investigated. The results show that 47Fe-36Ni-15Cr-1.5Mn alloy oxidizes at 1000°C under laboratory atmospheric pressure to form an oxide film layer dominated by Cr2O3 and (Fe, Ni, Mn) Cr2O4 spinel, and the oxidation curve of the alloy follows the parabolic law. After the addition of rare earth Y, rare earth phases precipitated along the grain boundaries in the alloy, and the more Y content, the more precipitated phases in the grain boundaries. The alloy with added rare earths was oxidized at a high temperature of 1000 °C for 2160 min, the oxidation law still followed the parabolic law, while the rare earth phase at the grain boundary reacted with the oxygen atoms infiltrated from the outside to generate a rare earth Y-rich oxide residing at the boundary between the grain boundary and the precipitated phase of the alloy. Add 0.5 wt.% rare earth Y 47Fe-36Ni-15Cr-1.5Mn-0.5Y alloy 1000 ° C high temperature oxidation of the formation of spinel oxide crystalline particles, dense and complete oxide film layer, the surface of the addition of a small amount of (0.5 wt.%) rare earth Y after the refinement of the oxide particles, and in the alloy grain boundaries in the form of oxides reside in the alloy to inhibit the cations in the matrix and the oxygen negative ions. and oxygen-negative ions in the alloy matrix, improving the antioxidant performance of the alloy. With the further increase of rare earth Y, during the oxidation of the alloy at high temperature, the precipitation phase at the grain boundary promotes the inward diffusion of oxygen, resulting in the deterioration of the antioxidant property of the alloy.

Carbonization of a biopolymer (lignin) in self-propagating high-temperature synthesis (SHS) led to the production of 2D graphene structures. With the help of modern analytical methods (Raman spectroscopy, X-ray diffraction) and electron microscopy, the resulting product was confirmed to have a few-layer 2D graphene structure. The predicted photovoltaic properties of the resulting few-layer graphene were implemented for laser ignition of a model pyrotechnic composition based on porous silicon. A phenomenological model of the formation mechanism of 2D graphene structures under the conditions of the SHS process is proposed.

Hafnium is a metal with rare properties, such as a low superconducting transition temperature slightly above 100 mK, which makes it attractive for a lot of applications, especially for design and fabrication of microcalorimeters with high energy resolution. In this paper we describe the results of fabrication and experimental investigation of superconducting properties of hafnium thin films in a dilution refrigerator. The considered Hf films, whose thickness is in the range from 60 to 115 nm, are deposited on substrates by electron beam evaporation. The combinations with thin layers of normal metals to decrease the critical temperature of superconducting hafnium films by proximity effect, are also considered. The critical temperature of the studied films varies from 56 to 302 mK. Also, significant increase of the critical temperature of some films over time was observed and investigated.

Abstract: An Al-Co-Y diffusion coating was prepared on a TiAl alloy by pack cementation process at a low temperature range of 650-720 ℃. The influence of different activators and co-deposition temperatures on the coating’s microstructure and formation process, and high temperature oxida-tion performance was studied. The results showed that NaF was a more suitable activator for preparing the Al-Co-Y diffusion coating on TiAl alloy compared to NH4Cl and AlCl3. A more compact coating structure can be obtained when deposition was performed at 680 ℃ using NaF as the activator. The coating was mainly composed of a TiAl3 outer layer, a TiAl2 inner layer, and a thin Al-rich TiAl inter-diffusion layer. The growth of the coating exhibited a positive linear correlation between coating thickness increase and the square root of deposition time. The high-temperature oxidation tests showed that a dense scale mainly composed of Al2O3 and a small amount of TiO2 formed on the coating after oxidation at 950 ℃ for 100 h. The scale possessed excellent high-temperature oxidation resistance, with a parabolic rate constant of the oxidation weight gain approximately 4.9×10-3 mg2/cm4 h, which is lower than that of the TiAl substrate by about three orders of magnitude, and lower than that of the pure Al diffusion coating more than one order of magnitude.

Microemulsions with excellent properties have shown significant potential for enhancing oil recovery from tight formations through spontaneous imbibition. This work present a high-temperature-tolerant lower-phase microemulsion (HTLP-ME) using a microemulsion dilution method. The properties and morphological characteristics of HTLP-ME were evaluated and proposed a enhanced spontaneous imbibition oil recovery mechanism using imbibition tests and CT scanning technology. The results show that the optimum concentration of HTLP-ME is 0.2wt% has a superior thermal stability, small particle size, lower IFT, good wettability alteration ability, and minimum adsorption loss. Imbibition and CT experiments showed that the longer the imbibition distance, the better is the effect on spontaneous imbibition oil recovery. Furthermore, the solubilization coefficient and self-driving force were defined and calculated to quantitatively analyze the imbibition mechanisms. The imbibition mechanisms demonstrate that the reduction of oil/solid adhesion is due to the synergistic effect of IFT reduction and wettability alteration, and the ability to increase the imbibition distance through a larger self-driving force.

In order to study the acoustic emission characteristics of sandstone under the action of the high temperature-water cooling cycle, the RMT-150B electro-hydraulic servo rock test system and the DS-5 acoustic emission detection and analysis system were used to conduct a single analysis of the sandstone after the high temperature-water cooling cycle. Experimental study on acoustic emission characteristics under axial compression, analyzing the deformation, strength and acoustic emission characteristics of sandstone under different temperatures and cycles. The results of the study show that the high temperature-water cooling action causes changes in the physical properties of the sandstone. The expansion rate of the rock sample decreases first and then increases when the temperature rises, and the strength first increases and then decreases. The number of cycles has little effect on the physical properties of the rock sample; sandstone acoustic emission ringing count increases with the increase of temperature and cycle times, acoustic emission activities become more frequent with the loading process; with the increase of cycle times and temperature, acoustic emission ringing counts and accumulative acoustic emission energy appear earlier The rock sample enters the elastic deformation stage ahead of schedule, the yielding period increases, and the rock sample presents a trend of transition from brittle failure to ductile failure; the ringing count and cumulative energy increase with the increase in temperature and cycle times, and the high-energy ringing count and cumulative energy increase. The simultaneous sharp increase of the rock sample is the harbinger of the failure and instability of the rock sample.

This study investigates the frequency dependence of the correlation or anticorrelation of ozone and temperature in the middle atmosphere. The anticorrelation of ozone and temperature plays a role for the expected recovery or superrecovery of upper stratospheric ozone in presence of manmade cooling of the middle atmosphere due to increasing carbon dioxide emissions. The correlation between lower stratospheric ozone and temperature indicates the dependence of lower stratospheric temperature trends on the ozone evolution in addition to greenhouse gas emissions. Ozone and temperature measurements of the microwave limb sounder (MLS) on the satellite Aura from 2004 to 2021 are utilized for Bern (46.95∘N, 7.44∘E) at middle latitudes and for the equator region. The time series are bandpass filtered for periods from 2 days to 5 years. The correlation coefficient depends on the period of the oscillation in temperature and ozone. The strongest correlation and anticorrelation are found for the annual oscillation. The anticorrelation between ozone and temperature in the upper stratosphere is about −0.7 at a period of 2 days and −0.99 at a period of one year. Thus, the temperature dependence of the ozone reaction rates also leads to an anticorrelation of ozone and temperature at short periods so that ozone can be considered as a tracer of planetary waves. At the equator, a dominant semiannual oscillation and an 11 year solar cycle are found for nighttime ozone in the upper mesosphere. The SAO in ozone and temperature show a strong correlation indicating a dynamical control of the ozone SAO in the upper mesosphere. The SAO in the equatorial nighttime values of ozone and temperature is due to a semiannual modulation of vertical advection by the diurnal tide.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

Chronic heat stress (CHS) has been exerting great pressure on the poultry industry due to the global warming. CHS-induced negative impacts deeply change the physiology, metabolism, egg production and meat quality of ducks. To reduce the increasing economic loss, different environmental strategies have been adopted. Here, we comprehensively compared three rearing modes for Cherry-Valley ducks (CVds) mainly by changing the environmental temperature. Plus, the transcriptome analysis and physiological anatomy were implied to investigate the underlying molecular biology and pneumonocyte dynamics. It turns out that the CVds affected by CHS have poor growth performance and bad carcass traits. In addition, the irreversible damage caused by CHS in the lung tissue of CVds was observed. Furthermore, several potential genes related to CHS have been found, such as HSPA8, IGF1, FGFR1, ACSL3, ACSL6, NR1H3 and GAPDH. This study strongly indicates the severe injury of CHS from the high-temperature environment and points out one of the adopting directions for duck rearing.

In this paper, the quality change of scallop (Patinopecten yessoensis) in the process of anhydrous storage and transportation after cold-acclimation and induced dormancy was studied, and the regulation mechanism of quality degradation in the storage and transportation in the process of gradient chilling stress and drying exposure was further explored. The results show that while being transferred from anhydrous storage and transportation from hydrous storage and transportation, the breathing pattern of scallops were changed from aerobic to anaerobic. Their gill filaments were altered, and the apparent vitality was constantly declining, which was reflected by the edge shrinkage of pallium and the direct proportion between the edge reduction rate and the stimulus response period. After being in the anhydrous state for 4d, the AEC value dropped to 67.59%. At this time, if they were under hydration again, they would resume a nice growth state. By virtue of proteomics, it was revealed from the analysis that cold acclimation and dry exposure mainly led to changes in biological functions and pathways such as mitochondrial inner membrane and ATP hydrolysis activity. In addition, it can be seen from the functional annotation and enrichment analysis of the metabolite KEGG that cold acclimation promoted the purine metabolism of scallops, while dry exposure inhibited the metabolism of saturated fatty acids. Besides, in this study, the infrared sensing mode was used for the first time to record the heart rate changes of the scallops during circulation, which provides feasibility for the nondestructive vitality monitoring of Lamellibranchia.

As shown previously, a relation between the superconducting transition temperature and some characteristic distance in the crystal lattice holds, which enables the calculation of the superconducting transition temperature, Tc, based only on the knowledge of the electronic configuration and of some details of the crystallographic structure. This relation was found to apply for a large number of superconductors, including the high-temperature superconductors, the iron-based materials, alkali fullerides, metallic alloys, and element superconductors. When applying this scheme called Roeser-Huber formula to Moiré-type superconductivity, i.e., magic-angle twisted bi-layer graphene (tBLG) and bi-layer WSe2, we find that the calculated transition temperatures for tBLG are always higher than the available experimental data, e.g., for the magic angle 1.1∘, we find Tc≈ 4.2–6.7 K. Now, the question arises why the calculation produces larger Tc’s. Two possible scenarios may answer this question: (1) The given problem for experimentalists is the fact that for electric measurements always substrates/caps are required to arrange the electric contacts. When now discussing superconductivity in atomically thin objects, also these layers may play a role forming the Moiré patterns. The consequence of such substrate-induced super-Moiré patterns is that the resulting Moiré pattern always will show a larger cell size, and thus, a lower Tc of the final structure will result. (2) A correction factor to the Roeser-Huber formalism may be required to account for the low charge carrier density of the tBLG. Here, we test both scenarios and find that the introduction of a correction factor η enables a proper calculation of Tc, reproducing the experimental data. We find that η depends exponentially on the value of Tc.

Ce-promoted NiMgAl mixed-oxide (NiCex-C, x = 0, 1,5,10) catalysts were prepared from the quaternary hydrotalcite precursors for CO2 hydrogenation to methane. By engineering the Ce contents, NiCe5-C showed its prior catalytic performance in low-temperature CO2 hydrogenation, being about 3 times higher than that of Ce-free NiCe0-C catalyst (TOF of NiCe5-C and NiCe0-C: 1.19 h-1 vs 0.39 h-1 @ 250 oC). With extensive characterization, it was found that Ce dopants promoted the reduction of NiO by adjusting the interaction between Ni and Mg(Ce)AlOx support. The higest ratio of surface Ni0/(Ni2+Ni0) was obtained over NiCe5-C. Meanwhile, the surface basicity was tailored with Ce dopants. The strongest medium-strength basicity and highest capacity of CO2 adsorption was achieved on NiCe5-C with 5wt% Ce content. The TOF tests indicated a good correlation with medium-strength basicity over the NiCex-C samples. The results showed that the high medium-strength and Ce-promoted surface Ni0 species endows the enhanced low-temperature catalytic performance in CO2 hydrogenation to methane.

To study the anti-cracking performance of cast-in-place concrete inner shaft lining structure under the combined effects of temperature and constraint, this paper first developed a novel temperature stress test machine suitable for the shape of the inner shaft lining structure and with adjustable endpoint constraint, providing specialized experimental equipment for subsequent cast-in-place concrete inner shaft lining temperature stress simulation experiments. Then, this paper preliminarily studied the temperature, strain, and stress changes of the cast-in-place inner shaft lining under the condition of 100% endpoint constraint by simulating the internal hydration heating and cooling process of the cast-in-place inner shaft lining and using the temperature stress test machine to accurately control the endpoint constraint conditions of the inner shaft lining scaled model.

The main goal of this work is to develop a novel boundary element method (BEM) model for analyzing ultrasonic wave propaga-tion in three-temperature anisotropic viscoelastic porous media. Because of strong nonlinearity of ultrasonic wave propagation in three-temperature porous media problems, the analytical or numerical solutions to the problems under consideration are always challenging, necessitating the development of new computational techniques. As a result, we use a new BEM model to solve such problems. A time stepping procedure based on the linear multistep method is obtained after solving the discretized boundary in-tegral equation with the quadrature rule. The calculation of a double integral is required to obtain fundamental solutions, but this increases the total BEM computation time. Our proposed BEM technique is used to solve the current problem and improve the formulation efficiency. The numerical results are graphed to demonstrate the effects of viscosity and anisotropy on the nonlinear ultrasonic stress waves in three-temperature porous media. The validity, accuracy, and efficiency in the proposed methodology were demonstrated by comparing obtained results to the corresponding solution obtained from finite difference method (FDM).

Selective Paste Intrusion (SPI) is an additive manufacturing (AM) process in which thin layers of aggregates are selectively bonded by cement paste only where the structure is to be produced. In this way, concrete elements with complex geometries and structures can be created. Reinforcement is required to increase the flexural strength of the concrete elements and, thus, enable their applicability in practice. Integrating the reinforcement is a difficult task, particularly in the case of SPI due to the layer-wise printing method. Especially with respect to possible complex structures, the production of the reinforcement needs to be adapted to SPI, thereby offering a high degree of freedom. One concept for a reinforcement integration is combining the two additive manufacturing processes SPI and Wire and Arc Additive Manufacturing (WAAM). However, since the two processes serve different fields of application, their compatibility is not necessarily given. Ongoing investigations show that the temperatures caused by WAAM adversely affect both, the cement paste rheology required for sufficient paste penetration into the particle bed and the overall concrete strength. This paper provides an overview of ongoing research focusing on different cooling strategies and their effects on the compressive strength of SPI-printed concrete parts.

As shown previously, a relation between the superconducting transition temperature and some characteristic distance in the crystal lattice holds, which enables the calculation of the superconducting transition temperature, Tc, based only on the knowledge of the electronic configuration and of some details of the crystallographic structure. This relation was found to apply for a large number of superconductors, including the high-temperature superconductors, the iron-based materials, alkali fullerides, metallic alloys, and element superconductors. When applying this scheme called Roeser-Huber formula to Moiré-type superconductivity, i.e., magic-angle twisted bi-layer graphene (tBLG) and bi-layer WSe2, we find that the calculated transition temperatures for tBLG are always higher than the available experimental data, e.g., for the magic angle 1.1∘, we find Tc≈ 4.2–6.7 K. Now, the question arises why the calculation produces larger Tc’s. Two possible scenarios may answer this question: (1) The given problem for experimentalists is the fact that for electric measurements always substrates/caps are required to arrange the electric contacts. When now discussing superconductivity in atomically thin objects, also these layers may play a role forming the Moiré patterns. The consequence of such substrate-induced super-Moiré patterns is that the resulting Moiré pattern always will show a larger cell size, and thus, a lower Tc of the final structure will result. (2) A correction factor to the Roeser-Huber formalism may be required to account for the low charge carrier density of the tBLG. Here, we test both scenarios and find that the introduction of a correction factor η enables a proper calculation of Tc, reproducing the experimental data. We find that η depends exponentially on the value of Tc.

This paper presents a calibration and thermal compensation method that aims to minimize cost and processing time while maintaining high accuracy. First, the number of positions to perform the calibration procedure is optimized, and then, based on this optimized calibration number, thermal compensation is performed, which is necessary for environments with large temperature variations, since calibration parameters change at different temperatures. The calibration procedures and algorithms were experimentally validated on marketed accelerometers. Based on the optimized calibration method, the calibrated results have been obtained nearly 100 times improvement. Thermal drift calibration experiments on the triaxial accelerometer show that the thermal compensation scheme in this paper can effectively reduce drift in the temperature range of -40°C to 60°C. The temperature drifts of x- and y-axes are reduced from -13.2 and 11.8 mg to -0.9 and -1.1 mg, respectively. The z-axis temperature drift is reduced from -17.9 to 1.8 mg. We have conducted various experiments on the proposed calibration method and demonstrated its capacity to calibrate the sensor frame error model (SFEM) parameters. Therefore, the MEMS sensors calibrated in this paper have certain engineering application values for tilt measurement.

Canola is the major oilseed crop of Canada. The de-oiled material is an important by-product due to its rich phenolic profile and high protein content. This co-processing stream from canola is primarily utilized as animal feed but represents an invaluable source of nutraceuticals. Microwave-assisted solvent extraction (MAE), as a green extraction method, has received considerable attention in recent times. The ease of use and application of many solvents at the same time makes the MAE one of the best methods for studying multiple solvents at the same time. The formation of canolol, from sinapine and sinapic acid, is primarily dependant on temperature which favors the decarboxylation reaction. Hence, MAE using green extractants can be used to enhance the yield of canolol. This study examined the effects of different pre-treatment temperature-time combinations of 140, 150, 160, and 170℃ for 5, 10, 15, 20 and 30 minutes on the extraction of canolol and other canola endogenous phenolic compounds. Three antioxidant assays assessed the antioxidant activity of the different extracts obtained by MAE confirming the microwave as a novel and versatile instrument for enhancing the yield of canolol. Improvements in the antioxidant activity of the different extracts further established the efficacy of the current method for isolating important natural phenolic derivatives for utilization by the nutraceutical industry.

Drought and high temperature often occur simultaneously will eventually affect rice (Oryza sativa L.) yield and seed quality. The objective of the study was to compare the effects of high temperature (HT) and water limitation (WL) during seed development and maturation on yield component, seed quality, and amylose content in aerobic rice cv. MRIA. Two experiments were conducted concurrently in greenhouse with ⁓35/26℃ subjected to elevated HT and/or WL; 5 days 38/28°C at 10, 15, 29 DAA and/or HT; 7 days at 40/28℃ at 8 and 21 DAA with 12h photoperiod in control environment growth chamber. Both experiments were respectively harvested at physiological maturity of 31 and 35 DAA. Grain yielded from the irrigated plant declined from over 27% to below 18% between 15 and 29 DAA. Combination stresses resulted in greater reduction of grain yield than single stress. Late seed development (29 DAA) had no effect either on yield component or seed quality as well as produce a high concentration in amylase content (16.7%) with greater germination capacity (91%). The non-stress plant harvested at 21 DAA resulted the highest percentage of germinated seeds (97%) whereas the vigour index (VI) was reduced to 70.3% and 58.9% at 8 and 21 DAA respectively. Extended plant stress to 7 consecutive days incurred the highest VI with low concentration of amylose content. There was a linear relationship incurred between seed amylase content with germination capacity and VI, however, there was an inverse relationship (R2 = 0.19) between amylase content with VI from plant treated with (HT and/or WL) for 7 days. The present results confirmed that the avoidance HT and WL during early (10 DAA) and mid (15 DAA) seed development with short duration of stress (5 days) obtained better in yield component, enhanced the seed quality and amylose concentration. The combined HT and WL damaged seeds’ quality were more than each stress alone. Therefore, avoiding HT and WL can be practically applied by farmers by irrigating throughout the rice plant during histodifferentiation to save water usage during seed maturation.

Glass fibers slowly dissolve and age when exposed to water molecules. Such a phenomenon also occurs when glass fibers are inside fiber-reinforced composites protected by the matrix. This en-vironmental aging results in the deterioration of the mechanical properties of the composite. In structural applications, GFRPs are continuously exposed to water environments for decades (typically design lifetime is around 25 years or even more). During their lifetime, these materials are affected by various temperatures, pH acidity levels, mechanical loads, and the synergy of these factors. The rate of the degradation process depends on the nature of glass, sizing, fiber orientation, and environmental factors such as acidity, temperature, and mechanical stress. In this work, degradation of typical industrial grade R-glass fibers, when inside an epoxy fiber-reinforced composite, is studied experimentally and computationally. A Dissolving Cylinder Zero-Order Kinetic (DCZOK) model was applied and could describe the long-term dissolution of glass composites, considering the influence of fiber orientation (hoop vs transverse), pH (1.7, 4.0, 5.7, 7.0, and 10.0), and temperature (20, 40, 60, and 80 °C). The limitations of the DCZOK model and effects of sizing protection, accumulation of degradation products inside the composite, and water availability were discussed. Experimentally dissolution was measured using ICP-MS. Like for the fibers, for GFRPs also, the temperature showed an Arrhenius-type influence on the ki-netics, increasing the rate of dissolution exponentially with increasing temperature. Similar to fibers, GFRPs showed a hyperbolic dependence on pH. The model was able to capture all of these effects, and the limitations were addressed.

Oxide semiconductors are conventionally being used as sensing materials in gas sensors, limiting the detection of gases at room temperature (RT). In this work, a hybrid of copper oxide (CuO) with functionalized graphene (rGO) is proposed to achieve gas sensing at RT. The combination of high surface area and presence of many functional groups in CuO/rGO hybrid material makes it highly sensitive for gas absorption and desorption. To prepare the hybrid material, a copper oxide suspension synthesized using copper acetate precursor is added to the graphene oxide solution during its reduction using ascorbic acid. Material properties of CuO/rGO hybrid and its drop-casted thin films are investigated using Raman, FTIR, SEM, TEM, and four-point probe measurement systems. We find that the hybrid material is enriched with oxygen functional groups (OFGs) and defective sites along with electrical conductivity (~1.5 kΩ/□). The fabricated QCM (quartz crystal microbalance) sensor with a thin layer of CuO/rGO hybrid, demonstrates a high sensing response which is twice the response of the rGO-based sensor for CO₂ gas at RT. We believe that the CuO/rGO hybrid can be highly suitable for existing and future gas sensors used for domestic and industrial safety.

The construction field uses up over one-third of the global energy consumption and contribute to 40% of CO2 emissions according to the International Energy Agency (IEA) and the 2020 annual reporter of United Nation, Goal 11 (Make cities inclusive, safe, resilient and sustainable) which discusses sustainable, safe and efficient buildings. Therefore, Morocco has a commitment to this program by publishing the law 47-09 of energy efficiency. This work aims to study the energy efficiency of two types of building, a conventional and a natural building. Conventional building is constructed using concrete, while the natural one uses sand clay and straws. As for the technique of making the natural building, it perpetually follows the same approach accustomed in rural zones of Atlas Mountains in Morocco. In this research we also simulate, temperature and humidity variation inside these buildings using TRNSYS software. Sketch Up software was employed to design these houses. The weather database is used for a typical meteorological year (TMY). In the case of natural building, many building configurations were simulated: roof insulation, floor insulation, different types of glazing and sun protection. What's more, the thermal comfort is revealed to be more conspicuous in the case of natural building.

Low night temperature (LNT) can be a practical and economical target in tomato breeding programs in terms of energy saving in greenhouses. This study was conducted to investigate the physiological responses to LNT using four tomato accessions of cherry and large fruit types with LNT tolerance and sensitivity grown in two greenhouses with night temperature set-points of 10 and 15°C for heating. LNT significantly reduced plant height regardless of fruit types and LNT tolerance. The number of flowers were significantly reduced in 10°C in cherry but not in large fruit types. Fruit set in 10°C was significantly lower in LNT sensitive accessions than tolerant ones regardless of fruit types, which was due to abnormal flower morphology in 10°C. Proline accumulation patterns between 10 and 15°C significantly differed between fruit types as well as between LNT tolerant and sensitive accessions. Chlorophyll content in 10 °C was significantly higher at later growth stages in LNT tolerant accessions than sensitive ones in both fruit types. No clear difference in photosynthetic parameters was observed between fruit types or tolerance and sensitive accessions except for photosynthetic rate, which was significantly lower in tolerant than sensitive accessions during early growing period. These results suggest that different tomato fruit types may have different mechanisms for LNT tolerance.

The rearing temperature of the immature stages can have a significant impact on the life-history traits and the ability of adult mosquitoes to transmit diseases. This review assessed published evidence of the effects of temperature on the immature stages, life-history traits, insecticide susceptibility, and expression of enzymes in the adult Anopheles mosquito. Original articles published through 31 March 2021 were systematically retrieved from Scopus, Google Scholar, Science Direct, PubMed, ProQuest and Web of Science databases. After applying eligibility criteria, 29 studies were included. The review revealed that immature stages of Anopheles arabiensis were more tolerant (in terms of survival) to a higher temperature than An. funestus and An. quadriannulatus. Higher temperatures resulted in smaller larval size and decreased hatching and pupation time. The development rate and survival of Anopheles stephensi were significantly reduced at a higher temperature than a lower temperature. Increasing temperatures decreased the longevity, body size, length of the gonotrophic cycle and fecundity of Anopheles mosquitoes. Anopheles mosquitoes exposed at 18° or 30 °C had a higher risk of dying compared to those exposed at 25 °C. Increasing temperature also significantly increased NOS expression and decreased insecticide toxicity. Both extreme low and high temperatures affect Anopheles mosquito development and survival. Climate change could have diverse effects on Anopheles mosquitoes. There seems to be inconclusive evidence of the effects of temperature on the development and survival of Anopheles species, and more studies are needed to clarify this relationship.

Season plays a key role in the development of outdoor spaces for pedestrians in hot humid cities. This research studies the influence of seasonal variations on pedestrian thermal comfort on the pedestrian level by means of meteorology and field observations of selected footpaths in the major tourist area of Malacca. This experiment was carried out on selected clear calm days indicative of each season during the development of a research project, and hourly meteorological transects from 10:00 am to 6:00 pm and questioned 200 respondents on their thermal awareness, comfort, and preferences were conducted. Adaptation, thermal comfort vote, thermal preference, age, season and hour of the day were significant non-meteorological factors, apart from meteorological information. The findings of analyzes showed that the thermal experience and expectation existed and in different seasons people changed perceptions for the outside thermal environment. Almost 80% local tourist and 55 % international tourist was accepted Physiologically Equivalent Temperature (PET) range affected by the local climate and thermal adaptation. The subjective thermal sensation on physiological equivalent temperature generated an acceptable physiological equivalent temperature of 32.6°C to 36.8°C based on the seasonal variations for Malacca tourist zone in Malaysia. These findings shed light on the optimal design of outdoor spaces for increasing the utilization rate. The seasonal variation must be taken into account so that the outdoor landscape design provides more opportunities for different seasons to communicate with the atmosphere and so enhance thermal comfort and utilization.

The primary purpose of the study was the determination of the spatial day-to-day variability of extreme temperatures in Poland and the dependency of large temperature changes on atmospheric circulation in accordance with the Grosswetterlagen (GWL) classification. The goal was implemented based on data from 1966 to 2015, made available by the Institute of Meteorology and Water Management – National Research Institute. Day-to-day changes in maximum and minimum temperatures were designated with a rate of ≥ 6 °C (large) and with a rate of ≥ 12 °C (very large) and their spatial distribution was presented. Finally, the analysis of the dependency of considerable temperature changes on atmospheric circulation in accordance with the Grosswetterlagen (GWL) classification was conducted. The obtained results showed that in Poland in the period 1966-2015 the number of large changes in both Tmax and Tmin slightly increased, although the fluctuations show spatial variability. Large changes in Tmax occur more frequently in spring, and in Tmin in winter. Large changes in Tmax and Tmin are mainly recorded during cyclonic circulation, however, the anticyclonic circulation types favour especially large decreases in Tmin.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

A galvalume corrugated sheet was utilized as formwork for a reinforced concrete beam in flexure. A numerical model was validated to the experimentally obtained data, and further adopted to simulate the behavior of this composite structure under elevated temperatures. The properties and constitutive stress-strain data of the basic materials were obtained from experiments, and superimposed into the finite element model. The study concluded that the load carrying capacity of the member decreased as a direct function on temperature increase, and the cracking moment was very sensitive to the temperature fluctuation. The elevated temperatures also altered the failure mode.

This empirical study investigates large urban park cooling effects on the thermal comfort of occupants in the vicinity of the main central park, located in Madrid, Spain. Data were gathered during hot summer days, using mobile observations and a questionnaire. The results showed that the cooling effect of this urban park of 140 ha area at a distance of 150 m is able to reduce temperature by an average of 0.63°C and 1.28°C for distances of 380 m and of 665 meters from the park. Moreover, the degree of the Physiological Equivalent Temperature (PET) index at a distance of 150 meters from the park is on average 2°C PET and 2.3°C PET less compared to distances of 380 m and 665 m, respectively. Considering distance from the park, the correlation between occupant Perceived Thermal Comfort (PTC) and PET is inverse. That is, augmenting the distance from park increases PET, while the extent of PTC reduces accordingly. The correlation between these two factors at the nearest and furthest distances from the park is meaningful (P-value <0/05). The results also showed that large-scale urban parks generally play a significant part in creating a cognitive state of high-perceived thermal comfort spaces for residents.

Temperature field is an essential attribute of metal additive manufacturing in view of its bearings on the prediction, control, and optimization of residual stress, part distortion, fatigue, balling effect, etc. This work provides an analytical physics-based approach to investigate the effect of scan strategy parameters including time delay between two irradiations and hatching space on thermal material properties and melt pool geometry. This approach is performed through the analysis of the distribution of material properties and temperature profile in three-dimensional space. The moving point heat source approach is used to predict the temperature field. To predict the temperature field during the additive manufacturing process some important phenomena are considered. 1) Due to the high magnitude of temperature in the presence of the laser, the temperature gradient is usually high which has a crucial influence on thermal material properties. Consequently, the thermal material properties of stainless steel grade 316L are considered to be temperature-dependent. 2) Due to the repeated heating and cooling, part usually undergoes several melting and solidification cycles. This physical phenomenon is considered by modifying the heat capacity using the latent heat of melting. 3) The multi-layer aspect of metal AM process is considered by incorporating the temperature history from the previous layer since the interaction of the successive layers has an impact on heat transfer mechanisms. 4) Effect of heat affected zone on thermal material properties is considered by the superposition of material properties in regions where the temperature fields of two consecutive irradiations have an overlap since the consecutive irradiations change the behavior of the material properties. The goals are to 1) investigate the effects of temperature-sensitive material properties and constant material properties on the temperature field. 2) Study the behavior of thermal material properties under different scan strategies. 3) Study the importance of considering the effect of heat affected zone on thermal material through the prediction of melt pool geometry. 4) Investigate the effect of hatching space on melt pool geometry. This work is purely employed physics-based analytical models to predict the behavior of material properties and temperature field under different process conditions, and no finite element modeling is used.

Water hyacinth (Eichhornia crassipes) is an invasive species that has modified ecosystem functioning in the Sacramento-San Joaquin Delta (Delta), California, USA. Studies in lakes and rivers have shown that water hyacinth alters water quality. In tidal systems, such as the Delta, water moves back and forth through the water hyacinth patch so water quality directly outside the patch in either direction is likely to be impacted. In this study, we asked whether the presence or treatment of water hyacinth with herbicides resulted in changes in water quality in this tidal system. We combined existing datasets that were originally collected for permit compliance and long-term regional monitoring into a dataset that we analyzed with a before-after control-impact (BACI) framework. This approach allowed us to describe effects of presence and treatment of water hyacinth, while accounting for seasonal patterns in water quality. We found that although effects of treatment were not detectable when compared with water immediately upstream, dissolved oxygen and turbidity became more similar to regional water quality averages after treatment. Temperature became less similar to the regional average after treatment, but the magnitude of the change was small. Taken together, these results suggest that tidal hydrology exports the effects of water hyacinth upstream, just as river flow is known to transport the effects downstream, creating a buffer of altered water chemistry around patches. It also suggests that although water hyacinth has an effect on dissolved oxygen and turbidity, these parameters recover to regional averages after treatment.

Surface urban heat island (SUHI) depicts the deteriorating thermal environment in high-density cities and local climate zone (LCZ) classification provides a universal protocol for SUHI identification. In this study, taking the central urbanized area of Guangzhou in the humid subtropical region of China as the study area, the maps or images of LCZ, land surface temperature (LST), SUHI and urban design factors were achieved by using Landsat satellite data, GIS database and a series of retrieval and classification algorithms, and the urban design factors influencing SUHI were investigated based on 625 samples of LCZs. The results show that in the summer daytime under the clear sky condition, the LST varied greatly from 26 °C to 40 °C and the SUHI changed in a wide range of -6 °C to 8 °C in the LCZs of the study area. Seven and five urban design factors influencing the summer daytime SUHI were identified for the two dominant LCZ of LCZs 1-5 (LCZ 1 to LCZ 5) and the mixed LCZ (containing at least three types of LCZs), respectively. The summer daytime SUHI prediction models were obtained by using the step-wise multiple linear regression, with the performance of R2 of 0.697, RMSE of 1.21 °C, and the d value of 0.81 for the model of LCZs 1-5, and the values of 0.666, 1.66 °C, and 0.76 for the model of the mixed LCZ, indicating that the models can predict the changes of SUHI with LCZs to a large and satisfactory extent. This study presents a methodology to efficiently achieve a large sample of SUHI and urban design factors of LCZs in the largely urbanized cities, and provides information beneficial to the urban designs and regenerations in the humid subtropical region.

Ultra Low Temperature Process (ULTP) involve the material cooling in temperatures close to the liquid nitrogen (-196 °C), which is different from the cold-treatment (CT) made in temperatures close to -80 °C. ULTP treatments could raise the tool steel wear resistance through microstructural change that occurs on the material, enhancing, that way, the tools and dies lifetime. To investigate the impact on the wear resistance of tool steel AISI D2, micro abrasive wear tests were carried out and an analysis based on the Archard’s law was considered, evaluating specimen mass loss by laser interferometry. Micro hardness tests, X-ray diffractometry, scanning and optical microscopy and quantitative evaluation of carbides with image analysis were carried out aiming material characterization. Micro-scale abrasion tests shown a wear coefficient k about 1.73E-7 e 2.61E-7 mm3/N.mm to the specimens that received the ULTP phase and 3.12E-7 mm3/N.mm to the conventional thermal treatment, representing a wear resistance increase of 16.3 – 44.5% to cryogenically treated specimens. The results demonstrated a micro hardness improvement, ranging from 0.9 - 4.7% for the cryogenically treated specimens, when compared to the bulk material. This effect is related, mainly, to the retained austenite transformation in martensite and to the increase in the amount of fine secondary carbides dispersed in the martensitic matrixes of cryogenically treated specimens with ULTP. The best wear resistance improvements, on micro-scale, were achieved when the ULTP step is performed immediately after tempering.

In this paper a novel type of a highly sensitive gas sensor device based on the surface photovoltage effect is described. The developed surface photovoltage gas sensor is based on a reverse Kelvin probe approach. As the active gas sensing electrode the porous ZnO nanostructured thin films are used deposited by the direct current (DC) reactive magnetron sputtering method exhibiting the nanocoral surface morphology combined with an evident surface nonstoichiometry related to the unintentional surface carbon and water vapor contaminations. Among others, the demonstrated SPV gas sensor device exhibits a high sensitivity of 1 ppm to NO₂ with a signal to noise ratio of about 50 and a fast response time of several seconds under the room temperature conditions.