Glass and ceramics have a fundamental and crucial role in our lives due to their properties and aesthetic decoration. However, they create serious environmental problems, mainly due to their high occupation of landfills and harmful emissions. Both wastes could be utilized to reduce the natural resources' adverse environmental effects and exhaustion. With increasing environmental concerns to reduce solid waste as much as possible, the concrete industry has adopted several methods to achieve this goal. Hence this study examines the performance of self-compacted concrete (SCC) utilizing various percentages of recycled waste materials such as those deposited from glass and ceramic industries. The idea of utilizing recycled waste materials in concrete manufacturing has gained massive attention due to their impressive results in rheological and mechanical state. Recycled glass (RG) and ceramic waste powder (CWP) were utilized to replace fine aggregate and cement, respectively. Five mixes were designed, including the control mix, and the other four mixes with different dosages of RG and CWP as fine aggregate and cement replacement ranging between 5 to 25%. Mixes were tested for both rheological and mechanical properties to evaluate their compilment with SCC requirements as per codes and guidelines. The results revealed that 20%CWP or less as cement replacement and 10% or less of RG as fine aggregate replacement would provide suitable rheological properties along with mechanical ones. Utilizing recycled glass and ceramic waste powder provides strength like the mix designed with natural resources, which helps us structure economically and environmentally friendly.

Involving industrial waste into economic circulation, in particular flotation waste from coal enrichment, is an urgent task. The coal preparation waste of ArcelorMittal Temirtau JSC was studied with a view to the possibility of using it as an alternative substitute for coke breeze in the sintering process. During a thermoanalytical study on a synchronous thermal analyzer STA 449 NETZSCH in dynamic mode with a heating rate of 10, 20, 30 °C/min in an air flow of 30 cm³/min in the temperature range 30–1000 °C, we determined the lower heat of combustion of carbon-containing material, change mass during calcination, change and rate of change in the mass of the sample, thermal effect of the process, the temperature of the beginning, end and maximum development of thermal effects. It has been established that the greatest mass loss is observed in the temperature range 580 °C- 610 °C, which is about 65–67% of the total mass of the organic component of coal. The maximum burnout rate corresponds to a temperature of 540–563 °C. The lowest calorific value of the studied waste was 15.9 MJ/kg. The results of thermal analytical research and technical analysis substantiate the possibility of using flotation waste in a mixture of up to 10% with coke breeze for combustion in the sintering layer for the production of sinter. Analysis of the composition of flotation waste showed that they have a high specific surface area (56.8∙10³ m²/kg), are highly dispersible, soggy, and capable of swelling, and the predominant amount of clay substance makes them a plastic material. The possibilities of using coal flotation waste as an alternative substitute for coke breeze have been studied after the regimes of its preparation for sintering have been developed and a rational regime of layer-by-layer combustion in the sintering layer has been established. The optimal ratio of coke and OPC in the fuel mixture of the sintering charge was determined.

In this work various sample of primary aluminum dross were investigated for composition and evaluation of hydrogen generation via hydrolysis in low concentration alkali solution. Composi-tion revealed low to moderate aluminium content and hydrolysis reactions showed low hydrogen generation volumes per sample mass as well as purity, where composition plays substantial role in the hydrogen evolution, yet showing that there is possible place for dross use in hydrogen generation. It was revealed that some dross samples in addition to hydrogen also release methane via hydrolysis. Rection rate was obtained by the shrinking core model, written for spherical solid particles. Sample composition on hydrogen generation volume is compared to known literature.

The eutrophication of open water bodies, especially in coastal water area, has received intensive public focuses in recent years. Biological treatment of organic pollutants in industrial and domestic wastewater requires microbial flora to participate. The environmental impact of these microbes, particularly in regard to the spread of antibiotic resistance genes and pathogenicity in coastal water, remains largely unknown. We initiate studies to examine antibiotic resistance genes (ARGs) in microbial flora and study the mode of antibiotic spread in the coastal waters of Bohai Bay, North China by using high performance liquid chromatography-mass spectrum analysis and quantitative polymerase chain reaction. The metabolic features of bacteria related to the presence of ARGs in the coastal area showed the enrichment of Pseudomonadale species with triple resistance properties (ampicillin, kanamycin and gentamycin) at the estuary site locating adjacent to a coastal sewage treatment plant where both type I and type II polyketide synthase genes and b-lactam type antibiotics are detected. Pseudomonadale order is phylogenetically belonged to Proteobacteria Phylum, Gamma-proteobacteria Class and contains Pseudomonadaceae family and Pseudomonas genus. QPCR analysis suggests that the percent occupation of Pseudomonadale species to total Proteobacteria in the examined stations is close to several sampling stations close to sewage treatment plants, where consistent release of organic wastes occurred.

Within the context of sustainable material development for the construction sector, this study explores the viability of panels composed of recycled newspaper-derived cellulose (9%), rice husk (14%), borax (15%), and polyvinyl acetate-based glue (62%). The methods employed involve water absorption and density tests, following ASTM C-1763 and C-303 standards. The fire resistance test conforming to the European standard UNE 23-725-90, and a mold growth test using AOAC 2002.11. The composite is prone to absorbing a significant amount of water when exposed to humid conditions. However, the incorporation of rice husk and borax can provide benefits such as improved moisture resistance compared to other cellulitic insulators, which may be advantageous in specific climates. Also, the developed composite has an intermediate density compared to other polymeric materials. This characteristic presents advantages in applications that demand a balance between strength and lightness. During the fire resistance tests, the samples with borax presented less fire propagation, and superficial damage compared with the specimens without borax. This is important, considering the fireproofing property, required in building materials. The presence of borax in the composite has an inhibitory effect on the growth of fungi and yeasts. These findings are consistent with previous research. Nevertheless, further research and testing are imperative to assess its viability and performance for commercial applications.

In the ongoing work, environmentally sound technologies for converting organic wastes into fertilizers, to improve soil sustainability and crop yield have been identified and assessed. Wet wastes were combined with 50% wood sawdust and 50% 50% wet wastes (Compost 1) or (10% Straw + 90% wet wastes) (Compost 2) to produce soil improvers with a balanced level of nutrients and their effectiveness on soil ecosystem functioning have been tested and compared to horse manure (HM) and nitrogen:phosphorous:potassium (NPK) fertilizers. Unfertilized soil was used as control. Soil chemical and biological properties, have been detected after the harvesting of broccoli and red cabbage (90 days from the initial treatments). Three independent experiments have been conducted in open field in a randomized complete block design with three replications (n=9). Results showed that Compost 1 had the highest C/N ratio and CSC, indicating a better humification of wet material. Compost 1 even if contained a minor amount of organic carbon, as well as a less activity of FDA and DHA than Compost 2, was the most effective in improving soil quality, significantly increasing the labile fraction of organic matter, the oxidative enzyme (DHA), microbial biomass and crop yield. Both composts increased crop productivity.

This article aimed to evaluate, using statistical tools, the generation and composition of urban solid waste (MSW) in the city of Belém, Pará, from nine urban collection sectors in the municipality, and the average nominal income of the population. Approximately 900kg of urban solid waste were col-lected from the municipality in the period from 2021 to 2022. Statistical tests were carried out on hypotheses with 5% significance in comparative evaluations, and their respective average nominal incomes. The results indicated that the organic fraction corresponds to 55.57% of the waste generated in the municipality, 14.26% is inert waste (potentially contaminating) and 0.67% is miscellaneous waste. It was observed that the waste generated by families with high purchasing power tends to contain higher percentages of recyclables, while in families with lower purchasing power the highest percentages tend to be organic. Knowledge of the generation of MSW is fundamental for the choice and dimensioning of operations and processes involved in the management chain at the municipal level. The decentralization of services offered based on solid waste management would enable greater success in serving the population.

This study aims to contribute to the characterization of Katangese Copperbelt's mining wastes and soils polluted with trace metals, using pollution indices and direct concentration measurements. The study also evaluated the use of these indices in assessing the success of remediation projects. Analytical data from previous studies and samples collected from six types of discharge and one polluted soil were used to address the first objective. Soil and plant samples were collected at Kipushi and Penga Penga for the second objective. The results revealed very high concentrations of As, Cd, Co, Cu, Mn, Pb, and Zn in all mine tailings and polluted soils, compared with local references. The degree of contamination (DC) values (from 72 to 5440) and potential ecological risk (RI) values (from 549 to 162 091) indicate very high-risk situations associated with polluted discharges and soils. Regarding revegetation trials, the results show lower concentrations and RIs in tree rhizospheres compared with unamended areas at both sites. However, trace metal concentrations are higher in tree rhizospheres compared with local references, and RI values are in the considerable risk range for Penga Penga (RI = 533) and very high (>1500) for Kipushi. Bioconcentration factor values are below 1, indicating low accumulation in roots, wood, and leaves, and low risk of contamination of the trophic chain. In this context, it seems that the pollution indices used are unsuitable for assessing the effectiveness of phytotechnology processes based on metal stabilization. Direct plant performance measurements combined with direct measurements of metals in substrates and plants to assess transfer and efficiency are more appropriate.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 98.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

This study provides a detailed investigation into the pathways through which microplastics from urban sources are transported to marine ecosystems, their distribution across different environments, and their impacts on marine life. Utilizing a combination of water and sediment sampling across urban, riverine, and marine environments, the research quantitatively assesses the concentration and types of microplastics present, and evaluates the ecological consequences of their accumulation in marine ecosystems. The findings reveal a significant concentration of microplastics in all examined environments, with the highest levels detected in urban areas, closely linked to industrial activities and inadequate waste management practices. The study documents a variety of microplastic polymers, with polyethylene (PE), polypropylene (PP), and polyethylene terephthalate (PET) being the most prevalent. A substantial impact on marine organisms was observed, including evidence of microplastic ingestion across a wide range of species and indications of stress and physical damage to coral reefs. Seasonal variations indicate that microplastic concentrations peak during periods of high rainfall, suggesting urban runoff as a critical pathway for microplastic transport. The study concludes with recommendations for improving waste management practices, enhancing public awareness and engagement in plastic recycling efforts, and implementing policies aimed at reducing the production and use of single-use plastics. This research underscores the urgent need for coordinated actions to mitigate the pervasive issue of microplastic pollution, highlighting the role of urban management and policy interventions in safeguarding marine ecosystems.

This research delves into a detailed exploration of the thermal decomposition behavior of bio-based polymers, specifically Thermoplastic Starch (TPS) and Poly(lactic acid) (PLA). The study focuses on the impact of three different heating rates under a nitrogen atmosphere, providing comprehensive insights into the thermal stability of these eco-friendly polymers. In particular, the TPS kinetic model is examined, encompassing the decomposition of three distinct fractions. In contrast, PLA exhibits a simplified kinetic behavior requiring only a fraction described by a zero-order model. The kinetic study involves a systematic investigation into the individual contributions of key components within TPS, including starch, glycerin, and polyvinyl alcohol (PVA). This nuanced analysis contributes to a comprehensive understanding of the thermal degradation process of TPS and PLA, enabling the optimization of processing conditions and the prediction of material behavior across varying thermal environments. Furthermore, the incorporation of different starch sources and calcium carbonate additives in TPS enhances our understanding of the polymer's thermal stability, offering insights into potential applications in diverse industries.

Modernizing the retail sector is essential to societal progress toward creating a smart city. The retail sector is crucial to the development of a smart city because of its adaptability and capacity for innovation. However, due to their perishability, supermarkets throw away a lot of fruits and vegetables. This article discusses the design of a sub-optimal process for processing sorted fruits using a reverse logistics approach, demonstrating how productivity can be increased despite constraints on processing capacity. This paper presents the results of a case study conducted in a Qatari supermarket that offers a variety of regular fruit processing techniques. In order to maximize output and cut down on waste, this project aimed to develop a reverse logistics system for imperfect fruit.

The “circular bioeconomy” offers numerous opportunities for the health, cosmetic, and nutrition sectors through the potential reuse of Castanea sativa by-products. This abundant and sustainable resource provides valuable bioactive secondary metabolites with antioxidants and anti-inflammatory properties. The transformation of these by-products into high-value products for human health can contribute to sustainable economic growth and reduce the environmental impact of traditional waste disposal practices, thus creating added value from previously underutilized resources. In the present study, we investigated the antioxidant capacity, phytochemical composition and in vitro antioxidant and anti-inflammatory activity of C. sativa burrs (CSB) aqueous extract. The spectrophotometric study yielded optimal total phenolic content (TPC) values, along with significant antioxidant and anti-radical properties. The utilization of UPLC-MS-MS techniques for phytochemical investigation resulted in the identification of a total of 56 metabolites, providing confirmation of the presence of phenolic compounds in CSB. In addition, CSB significantly downregulated pro-inflammatory mediators in LPS-stimulated RAW 264.7 macrophage cells without significant cell toxicity.

Hyperspectral imaging data holds great potential for the different stages of the mining life cycle in active and post-mining environments. However, the technology has yet to reach the stage of large-scale industrial implementation and acceptance. While hyperspectral satellite imagery can achieve high spectral resolution, signal-to-noise ratio (SNR) and global availability with break-through satellite systems like EnMAP, EMIT and PRISMA, limited spatial resolution poses chal-lenges for sectors like mining, which require decimetre to centimetre scale resolution for applica-tions such as reconciliation, ore/waste estimates, geotechnical assessments and environmental monitoring. Hyperspectral imaging from drones (referred to herein as Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the camp/ mine scale, with the capability for frequent, user-defined re-visit times. This has been made possible by the miniaturization of hy-perspectral imaging systems. Collection of data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions enables the detection of different minerals and surface altera-tion patterns potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we provide a review of relevant studies de-ploying hyperspectral imaging in or applicable to the mining sector, especially for the use of hy-perspectral VNIR-SWIR Uncrewed Aerial Systems. Where required, we draw on previous in-sights derived from satellite or ground-based systems. We also discuss UAS survey planning, and sampling considerations for validation and interpretation.

Sustainable manufacturing practices are becoming increasingly necessary due to the growing concerns regarding climate change and resource scarcity. Consequently, material recycling technologies have gradually become preferred over conventional processes. This study aimed to recycle waste polylactic acid (PLA) from household-disposed cups and lids to create 3D-printed parts and promote sustainable manufacturing practices. To achieve this, the current study utilised virgin and post-consumer PLA (sourced from household waste) blends. The PC-PLA wastes were shredded and sorted by size with the aid of a washing step, resulting in a filament with a 1.70 ± 0.5 mm diameter without fragmentation or dissolution. A 50:50 wt.% blend of virgin PLA (vPLA) and PC-PLA was selected as the standard recycling percentage based on previous research and resource conservation goals. The study investigated the impact of three 3D printing parameters (layer height (LH), infill density (I), and nozzle temperature (NT))on the quality of 3D-printed parts using a three-level L9 Taguchi orthogonal array. The findings revealed that blending PC-PLA with vPLA led to significant improvements in the tensile, flexural, and impact strengths by 18.40%, 8%, and 9.15%, respectively, compared to those of recycled PLA. This conclusion was supported by the investigation of the fracture surface area, which revealed fractographic features associated with printing parameters, such as plastic deformation and interfilament debonding. An ANOVA analysis revealed a positive influence of larger layer height and high nozzle temperature on the mechanical properties. Subsequently, the optimal printing parameters (LH: 0.3 mm, I: 100%, and NT: 215 °C) were determined using the S/N ratio, and a confirmation test using the optimum printing parameters exhibited a strong correlation with statistically predicted outcomes. Finally, the study used optimum printing parameters to fabricate 100% post-consumer recycled PLA 3D printed parts, demonstrating their potential for low-strength applications. Based on these findings, it can be concluded that virgin and post-consumer recycled PLA blended filament for fabricating 3D printed components is an effective way to support plastic recycling in the context of a circular economy.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

Food insecurity is an economic and social condition that involves individuals having limited or uncertain access to healthy food. Despite the well-intentioned efforts of both governmental and not-for-profit organizations in addressing food insecurity, well over one-in-ten households in the U.S., the wealthiest nation in the world, experience food insecurity every year. This literature review covered several government programs and research interventions designed to address food insecurity. Results from the review highlight how the Supplemental Nutrition Assistance Program (SNAP), The Emergency Food Assistance Program (TEFAP), and not-for profit food banks have demonstrated success in improving food insecurity. However, the prevalence of food insecurity among U.S. households has fluctuated without any sustained decreases that achieve a food insecurity rate that remains below 10 percent of the population. Food waste, which refers to food that is edible yet discarded at the retail or consumption phases, is rampant in the U.S., as approximately 30 percent (66.5 million tons) of edible food is wasted after leaving the farm every year. Food waste prevention efforts that involve rescuing edible, nutritious food and redistributing it to individuals who are food insecure can promote both environmental- and public health through simultaneous reductions in food waste and food insecurity.

Waste biogenic materials from seafood exploitation are valuable resources of new compounds exploitation within the blue bioeconomy concept. Here, we describe the effectiveness of Raman technology implementation as an in-line tool for demineralization process control of crustaceans or gastropods. We produced transparent chitin polymer foils from three waste crustacean shells (C. sapidus, S. mantis and M. squinado) using a slow, green chemical approach employing acetic acid, and showed the progressive process of biogenic carbonate dissolution and increasing the Raman characteristic signal of chitin, in a time dependence manner. It turned that chitin foils obtaining is species-specific, and the demineralization bath of waste shell mixture can be effectively tracked by Raman spectroscopy, for solvent control and the recovery of the calcium acetate as valuable by-product. Comparatively, calcium acetate drug, a compound widely used in kidney failure diseases, or as additive in nutraceuticals and food industry, has been obtained here, following a green demineralization path of the sea snail Rapana venosa intact shell, assisted by Raman tech-nology, using 9% acetic acid (vinegar) solution for 14 days. To validate the final products identity and quality, The process of waste shells demineralization and the final products of the treatment were investigated using various Raman techniques and technologies, cross-validating the results with FT-IR, XRD and SEM-EDX techniques. NIR Raman spectroscopy revealed chitin bands in a time-dependent manner, while Resonance Raman spectroscopy showed the preservation of ca-rotenoids after two weeks of acetic acid treatment. A hand-held flexible TacticID Raman system with a 1064 nm excitation demonstrated its effectiveness as a rapid, in-line decision making tool during process control and revealed excellent reproducibility of the lab-based instrument signal, suitable for in situ evaluation of the demineralization status and solvent saturation control. The calcium acetate recovered from residual treatment solutions was assessed regarding its hydration status, purity, and suitability as recrystallized material for further use as pharmaceutical product or ingredient in complex formulations.

The aim of this study was utilization of ground tea waste (GT) left after brewing the black tea as a biofiller of natural rubber (NR) composites. Ionic liquids (ILs), i.e., 1-ethyl-3-methylimidazolium lactate and 1-benzyl-3-methylimidazolium chloride, often used to extract phytochemicals from tea, were applied to improve the dispersibility of GT particles in elastomeric matrix. The influence of GT loading and ILs on curing characteristics, crosslink density, mechanical properties, thermal stability and resistance of NR composites to thermo-oxidative aging was investigated. The amount of GT did not significantly affect curing characteristics and crosslink density of NR composites, but had serious impact on tensile properties. Applying 10 phr of GT improved the tensile strength by 40% compared to unfilled NR. Further increasing in GT content worsened the tensile strength due to the agglomeration of biofiller in elastomer matrix. ILs significantly improved the dispersion of GT particles in elastomer and increased the crosslink density by 20% compared to the benchmark. Owing to the poor thermal stability of pure GT, it reduced the thermal stability of vulcanizates compared to unfilled NR. Most importantly, GT-filled vulcanizates showed improved resistance to thermo-oxidative aging, since the aging factor increased by 25% compared to the unfilled vulcanizate.

Plastic waste accumulation poses significant environmental challenges, underscoring the importance of closing the plastic life cycle by converting waste into valuable products. Pyrolytic char, a promising byproduct, offers diverse industrial applications. However, little attention has been given to converting hydrocarbon-based plastics into solid carbon due to their low fixed carbon content. This study compares sulfonation and thermal oxidation stabilization techniques for carbonizing waste polyethylene and polyvinyl chloride. Results indicate sulfonation yields higher pyrolytic char formation and improves surface properties, surpassing Al2O3 in catalyst support characteristics. Thermal oxidation increases fixed carbon content but adversely affects char yield and surface properties. Both methods effectively enhance fixed carbon content, but sulfonation emerges as more advantageous, suggesting potential use of plastic-derived char as a catalyst support material, contributing to circular economy development.

The global demand for rubber is on a steady rise, which is driven by the increasing production of automobiles and the growing need for industrial, medical, and household products. This surge in demand has led to a significant increase in rubber waste, posing a major global environmental challenge. End-of-life tire (ELT) is a primary source of rubber waste, which possesses significant environmental hazards due to its massive stockpiles. While landfilling is a low-cost and easy-to-implement solution, it is now largely prohibited due to environmental concerns. Recently, ELT rubber waste has garnered considerable attention for its potential applications in civil engineering and construction. These applications not only enhance sustainability but also foster a circular economy between ELT rubber waste and the civil engineering and construction sectors. This review article concentrates on the recent research progress and challenges in the civil engineering applications of ELT rubber waste. It also discusses commercially available recycled rubber-based construction materials, their properties, testing standards, and certification. To the best of the authors' knowledge, this is the first time such a discussion on commercial products has been presented.

Plastics play a pivotal role in the principles of a circular economy, where their effective recycling post-utilization, leading to economic value generation and minimal environmental harm, is crucial for achieving sustainable management. Extensive research has delved into the incorporation of waste plastics in concrete, showcasing promising outcomes with a myriad of advantages..The escalating volume of plastic waste is becoming a pressing issue, contributing to environmental pollution, particularly in densely populated cities and towns in Nigeria such as Delta, Aba, Port Harcourt, Onitsha, Enugu, Benue, and Ogun. These urban centers experience high consumption of goods packaged or sealed in plastic materials. Tourist destinations are also affected as large quantities of plastic waste are improperly disposed of or incinerated, resulting in environmental contamination and air pollution. Efforts to address this growing concern are crucial to safeguarding the environment and public health in these regions.Therefore, it is imperative to find effective ways to utilize these waste plastics. By cleaning low-density polyethylene bags and combining them with sand at specific proportions, high-strength bricks can be produced. These bricks not only exhibit thermal and sound insulation properties but also help in pollution control and cost reduction in construction projects. This innovative approach not only addresses the issue of accumulating plastic waste, a non-biodegradable pollutant, but also offers a sustainable solution to manage plastic waste while contributing to the construction industry's efficiency and environmental protection., By incorporating waste plastic and nylon into brick production, we not only reduce the amount of sand extracted from our natural resources like rivers and seas but also utilize the surplus plastic waste that is currently discarded. This research focuses on creating eco-friendly bricks by incorporating molten plastic, nylon, and plastic bottles in varying percentages (0 to 15% by weight) along with 5kg of fly ash. The experimental results from this study will shed light on the feasibility and benefits of using these materials in brick manufacturing, highlighting the potential of sustainable construction practices that minimize environmental impact and resource depletion, The experimental process involved utilizing cement and sand to complete the brick composition, with curing conducted underwater for 29 days followed by baking at temperatures between 100°C to 120°C for 2 hours. The resulting eco-friendly bricks exhibited key characteristics such as being lightweight, porous, having low thermal conductivity, and displaying appreciable mechanical strength. Interestingly, the compressive strengths of these bricks, post the addition of waste plastic and nylon, were found to be comparable to that of conventional bricks. Additionally, these eco-friendly bricks showcased reduced water absorption capacity compared to regular bricks, offering a promising alternative for sustainable and efficient construction practices.The eco-friendly bricks made from A, B, C, and D using 0%, 5%, 10%, and 15% plastic/nylon waste showed comprehensive strengths of 19.5 ,19.46, 20.3, and 21.1 respectively, with corresponding water absorption percentages of 0.34, 0.25, 0.22, 0.20, and 0.085. The efflorescence values were lower than those of normal bricks. These bricks are likely to enhance energy efficiency in buildings and provide economic value to manufacturers, thereby promoting a sustainable ecosystem for plastic waste management with the involvement of all stakeholders.

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

Sustainable supply chain management (SSCM) represents a critical strategy for the electronics industry to balance economic objectives with environmental and social responsibility across complex global production networks. This multiple case study analysis investigates SSCM integration within leading Korean electronics manufacturers Samsung, LG, and Hyundai. In-depth qualitative data, focus groups, and sustainability report analysis reveals the policies, practices, results and implementation barriers related to incorporating sustainability criteria across procurement, manufacturing, distribution and recycling functions. Findings show sustainability considerations increasingly driven by cost, risk, reputational and regulatory factors, with vertical coordination initiatives helping transfer knowledge to assist suppliers on compliance and emissions reductions. Yet substantial obstacles persist around monitoring, coordination, transparency and technical capabilities, especially amongst lower tiers. The paper discusses how common reporting standards, ethical sourcing certification and partnerships can accelerate electronics supply chain sustainability. By mapping integration achievements and gaps, this study informs managerial best practices and policy reforms toward promoting socially and ecologically responsible models for Korea's vital export industry as it navigates rising stakeholder pressures.

Abstract Global marine fish harvest has reached a plateau over the last decade. Efforts to increase aquaculture tend to face limitations in water resources and contamination problems. Of the current fish harvest at least 50% is discarded as waste. The chemical and microbiological contaminations limit the utilization of harvested fish. There is a need to improve fish preservation to minimize spoilage and process them into more appealing products. Instead of resorting to individual food processing methods, the efficiency of processing could best be increased by a combination of conventional and modern processing methods, or combinations of modern processing methods. Fish waste is a rich source of oils containing essential fatty acids, polypeptides, and amino polysaccharides that could be utilized through upscaling of the current scientifically proven methods, to new processing technologies. Separation of collagens, gelatins, bioactive peptides, edible fish oils, and chitosan form the primary stages in the utilization of fish waste. The products need purification to meet food quality and safety standards, and desirable industrial characteristics. The diversity of information and products generated through new methods requires advanced data handling and prediction systems, such as artificial intelligence, to address food safety and get the best out of fish processing and utilization.

The global increase in population has placed significant pressure on food security, leading to the emergence of aquaculture as a vital source of aquatic foods. However, rising costs and the limited availability of fishmeal in aquafeeds have spurred the search for alternative protein sources. While plant-based ingredients have been integrated into commercial aquafeeds, they come with challenges, including low protein content, palatability issues, and the presence of antinutritional factors. In this context, fish silage, derived from fish waste and discarded fish, stands out as a promising alternative technology due to its cost-effectiveness and sustainability attributes. The production of fish silage involves the addition of organic/inorganic acids or lactic acid bacteria to homogenized fish waste. This process yields a valuable mixture rich in peptides, free amino acids, and partially hydrolyzed proteins, offering significant nutritional benefits for animal diets. Beyond its nutritional advantages, fish silage contributes to environmental sustainability by reducing the impact of waste disposal and enhancing the value of fish waste. The objective of this review is to promote sustainable practices in the aquaculture industry in response to the increasing demand for high-quality feed nutrients. To achieve this, it includes an analysis of research results related to silage technology, an appraisal of the advantages and disadvantages of using fish silage as a feed additive, and a focus on emerging trends in this field.

In the era of mounting water scarcity, particularly in arid regions, the agricultural sector is striving to optimize the water resource management practices. Treated wastewater (TWW) has emerged as a viable alternative to freshwater for irrigation, offering a sustainable solution to water conservation. However, ensuring the safety and quality of TWW is paramount to safeguard for both crop health and environmental integrity. Electrical conductivity (EC), a critical factor in assessing TWW suitability for irrigation, can significantly impact crop yields and soil health since it is directly linked to the concentration of dissolved salts and ions. Therefore, this study delves into the development of advanced predictive models for EC assessment by employing supervised machine learning (ML) techniques like the Support Vector Regression (SVR), Adaptive Network-based Fuzzy Inference System (ANFIS), and Multiple Linear Regression (MLR). The TWW samples collected from Al-Qatif area, Saudi Arabia were assessed in the lab through a sensor-based real-time monitoring system integrated with Internet of Things (IoT) network and a multiprobe device. The key water quality parameters assessed involved, temperature (T), pH, Oxidation Reduction Potential (ORP), Resistivity (RES), Total Dissolved Solids (TDS), Salinity and Turbidity which served as the foundation for these models, given their profound influence on and their anticipated impact on EC levels. Following feature selection, two distinct model combinations were identified for the SVR, ANFIS and MLR models. Furthermore, to evaluate prediction performance, four statistical criteria, including coefficient of determination (R²), correlation coefficient (R), mean square error (MSE), and root mean square error (RMSE), were employed. Overall, the comparative performance results proved that ANFIS-M2 indicated the strongest predictive capability with the R² value of 0.99572 and 0.75145 and the RMSE values of 0.00965 and 0.01134, respectively in both calibration and verification stages.

The consistent and continuous growth in the world’s population is creating many challenges for public policymakers in the different life areas, including dealing with the increasing amounts of waste that are generating problems involving air and land pollution and a shortage of land for waste disposal. This study presents the results of public policy on managing municipal waste, as manifested in the quantity and rate of waste collected throughout Israel in recent years and disposed of in the various landfills and in analysis of the political and economic factors affecting this policy. The study combines a quantitative and qualitative approach, where the quantitative study includes analysis of statistical data based on information from the Central Bureau of Statistics, the Ministry of Environmental Protection, the Ministry of Finance, and others, and the qualitative study relies on reading and analyzing primary documents of the different government ministries on Israel’s waste disposal policy and information in the media on this issue. The research findings attest to an increase in the amount of municipal waste dumped in Israel, a merely slight decrease in the rate of landfilling as a proportion of all municipal waste disposal, and a merely slight increase in the rate of municipal waste recycled in recent years. The research conclusions stress the effects of the landfill levy and the Cleanliness Maintenance Fund on one hand, and of the government instability in the Ministry of Environmental Protection, the positivist policy embraced by decision makers in the Ministry of Environmental Protection, and the power struggles between Israel’s different ministries on the other, as the respective economic and political factors affecting Israeli policy on municipal waste management.

Continuity of activities and projects are important for sustainably developing organizations, especially universities. The purpose of this research study is to find university development guidelines regarding waste management according to the green university ranking criteria for sustainable developments by studying and collecting the data covering the last five years (2019 - 2023) of Mahasarakham University. We also analyzed and synthesized lessons learned from the details of the operations and the factors involved in successes while comparing and providing suggestions for the operations in the next year. It was found that waste management that resulted in continuous developments that achieved the goals of Mahasarakham University consisted of the five guidelines. (1) Making green university policies and using them as the (key performance index) KPI of the divisions and also announcing the university's waste management policies by applying the principles of 3R (Reuse-Reduce-Recycle). (2) Allocating the budgets supporting the projects' activities according to the evaluation criteria. (3) Student and personnel participation as well as the mechanisms used by the committees from various administrative divisions such as Student Council, Student Association and clubs to drive the operations. (4) Identifying the main responsible individuals and committees for the green university who communicated and drove the operations while collecting, analyzing and preparing the data. (5) Follow-ups and evaluations of the project's activities with the Plan-Do-Check-Act (PDCA) processes for continuous and sustainable developments and improvements leading to the green university. With the above operations, Mahasarakham University's waste management scores of the six indices during 2019 - 3023 increased annually as follows: 900, 900, 1050, 1275 and 1350.

Anaerobic digestion of waste material to biogas, with the remaining digestate slurry used as agricultural biofertilizer, is already a route of sustainable fuel production and its uptake will grow further. However, the foam layer that forms on top of the reacting mixture impedes the process and leads to liquid and solid material contaminating the gas product. Ideally, any effective foam repression should be low-cost, and react fast. Therefore, methods of optimizing anaerobic digestion need foam repression as one of the parameters in increasing gas yield. Foam can be repressed by pre-treating substrate which destroys filamentous bacteria and adding trace elements. The drawback to this method is the high cost of pre-treatment, the trace elements not being biodegradable and being toxic at high concentration; this method does not completely repress foam and is only effective under moderate organic loading

A study was carried out in a Waste Sorting Plant (WSP) located in France and treating dry recyclable household waste (DRHW) as well as dry recyclable commercial and industrial waste (DRCIW). The aim was to investigate the exposure to bioaerosol and dust. The aim of the study was to assess the extent to which the measurement of concentration, species composition and particle size distribution can contribute to a better assessment of the biological risks associated with exposure. Both stationary and personal bioaerosol and dust samples were collect in the (WSP). The results confirm that waste and waste sorting activities are sources of airborne fungi. Indeed, ambient concentrations ranged from 7.3×103 to 8.5×105 CFU/m3 for culturable moulds and up to up to 4 mg/m3 for dust. Personal exposure to inhalable dust was found up to 3 mg/m3 for dust and ranged from 8.6×103 to 1.5×106 CFU/m3 for fungi. Airborne fungal communities were found to be dominated by the Penicillium genera in both bioaerosols and settled dust samples, followed by the Aspergillus, Cladosporium, Wallemia, Mucor, and Rhizopus genera. Fungi were carried by particles of aerodynamic diameters mainly between around 2.0 and 10.0 µm. The findings dealing with size distribution and biodiversity of bioaerosols suggest that employees are exposed to complex bioaerosols during their work and helps to make a finer diagnosis of the risks involved, which is often difficult in the absence of any OEL for bioaerosols in general.

Objective: The aim of this study is to explore what inside the lipid lump obtained from skin. Try to understand the reasons for these physiological functions. In this paper, the lipid droplets or lumps was aimed to shed light on, figuring out what kind of cracks from metabolism were embedded inside. Results: A novel method was introduced for the detection of pathogens within lipid droplets extracted from acne or inflamed pores, as well as normal pores, using microscopic analysis. Through this technique, the presence of cracks from our body within these lipid droplets were identified. Methods: Observations were conducted using a microscope, with samples placed on slides and grind like blood smear. To enhance the transparency of the samples, tween-20 was utilized. This reagent was first time to be used for observing such big lipid lump of skin secretion. The evidences were recorded using the DMi8 camera from Leica.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

The organic fraction of municipal solid waste (OFMSW) is a significant environmental threat, and an economic and social challenge to manage. As such, the efficient treatment of OFMSW is a significant key factor in achieving sustainable waste management. Decentralized Composting (DC) develops a new framework of waste management. The DC Analysis Model (DCAM), proposed in our previous study, provides a powerful tool for decision makers, based on the quantification of the DC project characteristics. In this paper, we focus on the qualitative analysis as a complementary tool to support decision making, in cases where quantitative analysis is unequivocal. The qualitative analysis identifies the main players in the field, the critical stakeholders and the potential conflicts between them. It also reveals the root problems and the core competencies for the project's implementation. DCAM qualitative analysis in Shefa-Amr (case study) indicates that unresolved root problems, such as the “lack of national regulation”, “clear ownership of the project” and “lack of ongoing budget” can result in an unsustainable composting system. Countering that, “the commitment of the municipality”, together with “economic viability” and securing “suitable areas for placing composters” are among the most important core competencies for the effective implementation of DC projects.

In this study on volume determination in waste sorting facilities, we evaluate the effectiveness of ultrasonic sensors and address waste-material-specific challenges. Although ultrasonic sensors offer a cost-effective automation solution, their accuracy is affected by irregular waste shapes, varied compositions, and environmental factors. Notable inconsistencies in volume measurements between storage bunkers and conveyor belts underscore the need for a comprehensive approach to standardize bale production. With prediction reliability being constrained by limited data sets, undocumented modifications to machine-settings and sensor failures, this task renders a challenging application area for Machine Learning. We explore related research and present dataset analyses from three distinct waste sorting facilities in Europe, addressing issues as sensor usability, data quality and material specifics. Our analysis suggests promising strategies and future directions for enhancing waste volume measurement accuracy, ultimately aiming to advance sustainable waste management.

The regional recycling of plant waste from municipal green space maintenance, private households and private gardens is traditionally carried out in partially open composting plants. In addition to climate-relevant gases, dust, germs and odours are emitted. Compared to aerobic rotting the pyrolysis at higher temperatures and/or reforming offers industrial utilisation of plant based biowaste, with additional availability of energetic by-products. A high-quality plant charcoal derived from a pilot plant is used in a one-year field trial to establish a theoretical comparability with substrates from composting. The advantages and disadvantages of composting and high-quality pyrolysis is shown for comparison, to foster further investigation in advanced technologies for production of plant charcoal aiming the sequester of biogenic Carbondioxide.

The global food system has three recognized challenges: (a)increasing the availability of food consumption, (b) reducing food loss, and (c) reducing food waste. The increasing demand for food consumption, increasing quantity of food loss, and corresponding increase in food waste are resulting in serious health, aesthetic, social, economic, and environmental problems due to a lack of appropriate planning and management. Despite its importance, there is no clear, concise, and comprehensive definition of food consumption, loss, and waste. Generally, food consumption, food loss, and food waste are dealt with separately. This article presents a logically constructed ontological framework of food consumption, loss, and waste. It gives equal importance to all three aspects of global food management. The systematic ontological framework is general, and the analysis can be applied to any country. The framework deconstructs the combinatorial complexity of the problem and explicates the pathways to manage the consumption, loss, and waste. The ontological framework encapsulates 19*8*7*4*5*6 = 25,536 possible components of the challenge. A critical analysis based on available data using the framework will help to develop strategies to deal with the problem. It can help to discover the gaps and to find ways to bridge the gaps. It is novel to conceptualize food consumption, loss, and waste together.

This study investigated the presence, distribution, and antimicrobial resistance profiles of extend-ed-spectrum beta-lactamase (ESBL)-producing Enterobacteriaceae in a dairy herd located in Northern Italy. A questionnaire was administered, and the feces of clinically healthy pre-weaned dairy calves, their mothers, and the cows treated for mastitis, waste milk, water, and environmental samples, were collected and inoculated on Chromagar ESBL™ medium. The questionnaire identi-fied several risk factors including administration of waste milk to male calves, lack of routine cleaning of calf feeding and housing equipment, and blanket dry cow therapy. Escherichia coli was identified by MALDI-TOF MS in the feces of 28 of 37 (75.67%) calves, 2 of 3 (66.67%) treated cows, 8 of 14 (57.15%) environmental samples, and the waste milk. Six of 14 (42.85%) environmental samples were also positive for ESBL Acinetobacter baumannii, while all fecal samples were negative. ESBL production was confirmed for all E. coli isolates based on the double disk susceptibility test (DDST), while none were carbapenemase producers. Upon minimal inhibitory concentration (MIC) analysis, all of them showed multiple resistances and were categorized as multi-drug resistant (MDR). This study confirms the widespread presence of MDR, ESBL-E. coli in dairy calves and highlights their diffusion in the farm environment.

Lavander distillation leads to huge quantities of solid waste produced yearly. This waste is usually discarded resulting in serious environmental issues. However, it still contains residual essential oil and other bioactive compounds. This research reports on the development and comparison of optimized solid-liquid separation methods, i.e. microwave (MAE) and ultrasound assisted extraction (UAE) of phenolic compounds from lavender distillation waste. Optimal pretreatment conditions, such as waste moisture content and particle size were also determined. The extracts were spray or freeze-dried and the resulting powders were characterized for their physicochemical properties. The majority of the original phenolic compounds in lavender were found in the leachate fraction after distillation (61%), while 43% in the solid waste. Drying of the solid waste before extraction affected the process efficiency. UAE led to higher phenolic content and antioxidant properties compared to MAE. Drying (spray or freeze) the extracts did not significantly affect their phenolic content, while the use of maltodextrin as a drying agent improved the drying process yield especially in the freeze-drying method. It is concluded that valorization of lavender distillation wastes can be achieved via an integrated process consisting of a green extraction method and a consequent drying process that result in a stable bioactive powder.

The purpose of this study is to assess the solid waste management status and practice in Sendafa town, Oromia regional state residents. In order to achieve this goal, the researcher intends to employ both primary and secondary data from the Sendafa town municipality. With the aid of multi-cluster sampling and a purposive sampling method, the researchers chose a sample size of 398 people and 10 interview responders. To utilize a systematic sampling technique at intervals of residences, individual samples were chosen. Quantitative data was cleaned and analysed using STATA software. A multiple linear regression model and logistic regression other descriptive statistics methods were then used to change the results. The qualitative data were imported, coded, and thematised using ATLAS.ti.9 in order to prepare respondents' interviews for analysis. The findings indicate that residents' poor solid waste management practices are a result of a lack of awareness, low family income transportation issues, issues with waste collectors, a lack of a sense of responsibility and belonging, and a failure to enforce current solid waste management laws. Solid waste accumulates near roads, bridges, and residential areas that are close to landfills, contaminating the area and leading to diseases like TB and Asthma (and other related health issues in children and adults who live there). Thus, researcher recommends that to have sustainable solid waste management the town administrators should have plan to develop awareness creation symposium or panel of discussion, resolve transportation issues, monitor and guide the routine activities of waste collectors, develop sense of belongingness for themselves and for the community, develop integrated solid waste land fill projects and working with all stakeholders like NGO and health institution will minimize the adverse effect of improper solid waste management. Keywords: Solid Waste, Status of Solid Waste Management, Land fill site suitability

Onion skin waste (OSW), the primary non-edible byproduct from onion processing, offers a renewable source of bioactive compounds. This study aims to valorize OSW through subcritical water extraction (SWE), aligning with circular economy and biorefinery principles. SWE was carried out at 145 °C, 50 bar and 50 min in a discontinuous reactor, producing a phenolic-rich extract (32 ± 3 mg/g), dominated by protocatechuic acid (20 ± 3 mg/g), quercetin-4´-O-glucoside (7.5 ± 0.2 mg/g), and quercetin (3.2 ± 0.6 mg/g). Additionally, it contains sugars (207 ± 20 mg sucrose-Eq/g), proteins (22.8 ± 1.6 mg BSA-Eq/g) and free amino acids (20.4 ± 1.2 mg arginine-Eq/g). Its phenolic richness determines its scavenging activity against ●NO and O2●- radicals, and its α-glucosidase and aldose-reductase inhibition without affecting α-amylase. Notably, the extract demonstrates significant α-glucosidase inhibition (IC50 = 76 ± 4 µg/mL), surpassing acarbose (IC50 = 129.5 ± 1.0 µg/mL), in both pure enzyme and cell culture tests without showing cytotoxicity on AGS, HepG2 and Caco-2 human cell lines. The extract’s bioactivity and nutritional content make it suitable for developing antioxidant and antidiabetic nutraceutical/food components, highlighting the SWE potential for OSW valorization without using organic solvents.

Hong Kong is the biggest consumer of eggs in the world and ranks on the top with an average consumption of 24.52kg/capita/year. The egg consumption trend in Hong Kong has been increasing specifically; a drastic increase of about 100% has been observed from 2008 to 2020. One of the reasons behind this significant increase is the increase in the gross national income of Hong Kong in addition to the population growth rate. However, there was a slight decline in egg consumption trend in the year 2020 amid the COVID-19 pandemic. It has been estimated that there was a bulk of 17,100 tons of recoverable waste eggshells in 2019 (pre-COVID-19 situation), having a daily yield of 47 tons per day. Based on the linear regression, it may be expected that if the pre-COVID-19 trend of egg consumption remains sustained, there will be a big bulk of more than 45,000 tons per year and up to 125 tons per day of waste eggshells till 2050. In addition, a public survey was conducted across the city targeting individuals, families, and restaurants majorly on egg consumption and reuse. The survey outcomes revealed that Chinese eggs have an extensive market in Hong Kong, and people have a positive attitude towards eggshell recycling. Also, a massive population disposes of the waste eggshells while only a trace population reuses them. Therefore, Hong Kong has a very high potential to improve the circular economy by reusing waste eggshells on a commercial level in cementitious products.

Red mud (RM), a bauxite residue, contains hazardous radioactive wastes and alkaline material and poses severe surface water and groundwater contamination risks, necessitating recycling. Pretreated RM can be used to make adsorbents for water treatment. However, its performance is affected by many factors, resulting in a nonlinear correlation and coupling relationship. This study aimed to identify the best formula for an RM adsorbent using a mathematical model that examines the relationship between 11 formulation types (e.g., pore-assisting agent, component modifier, and external binder) and nine properties (e.g., specific surface area, wetting angle, and Zeta potential, among others). This model was built using a back-propagation neural networks(BP) based on single-factor experimental data and orthogonal test data. The model trained and predicted the established network structure to obtain the optimal adsorbent formula. The RM particle adsorbents had a pH of 10.16, specific surface area(BET) of 48.92 m2·g−1, pore volume of 2.10 cm3·g−1, compressive strength(ST)) of 1.12 KPa, and 24-h immersion pulverization rate(η_m) of 3.72%. In the removal of total phosphorus in flotation tailings backwater, it exhibited a good adsorption capacity (Q)and total phosphorous removal rate(η) of 48.63 mg·g−1 and 95.13%, respectively.

The characteristics of excess aerobic granular sludge, related to its structure and chemical composition, limit the efficiency of anaerobic digestion. For this reason, pre-treatment methods and compositions with other organic substrates are used. The aim of the research was to determine the effects of co-digestion of pre-hydrodynamically cavitated aerobic granular sludge with waste fats on the efficiency of methane fermentation under mesophilic and thermophilic conditions. The addition of waste fats improved the C/N ratio and increased its value to 19. The greatest effects were observed in thermophilic anaerobic digestion at 55°C, where a 15% waste fat content in volatile soilds was ensured. This resulted in the production of 1278.2±40.2 mL/gVS biogas and 889.4±29.7 mL/gVS CH4. The CH4 content of the biogas was 69.6±1.3%. The increase in biogas and CH4 yield compared to pure AGS anaerobic digestion was 34.4% and 40.1%, respectively. An increase in the proportion of waste fats in the substrate had no significant effect on the efficiency of methane fermentation.

In the face of 21st-century environmental challenges, including climate change, migration pressures, and waste disposal issues, certain healthcare sectors, notably dentistry, pose a significant global environmental footprint with concerns about carbon emissions and waste production. This scoping review delves into the paradox that healthcare, while dedicated to safeguarding health, inadvertently contributes to environmental degradation through waste accumulation and disposal. The analysis of relevant pertinent literature emphasizes the imperative for an environmentally sustainable approach to dental waste measurement, disposal methods, and comprehensive education for stakeholders. Aligned with the World Conference on Sustainable Development and the United Nations' 2030 Agenda, the study adhered to PRISMA-ScR scoping review guidelines and Institute of Medicine's recommendations. The study utilized Medline/PubMed and international organization websites for data retrieval, employing Boolean operator queries in Medline. A systematic literature analysis identified six cross-sectional studies (2004-2018) highlighting variations in dental waste composition due to the lack of standardized identification methods. This heterogeneity underscores the need for a proposed research model, emphasizing comprehensive methodologies and healthcare staff training in waste management. The study advocates for environmentally conscious dental practices, contributing to broader sustainable healthcare goals through sharing of a research protocol for dental solid waste management.

The global focus on geopolymer binder production has increased due to the adoption of waste materials and industrial byproducts. Given the gradual decline of the availability of fly ash and ground granular blast furnace slag (GGBFS) resulting from the decarbonization process in electricity and steel productions, waste clay brick powder (WCBP), could be a viable substitute of these pozzolanic by-products. This research is dedicated to thoroughly investigate the techno-eco-efficiency performance of WCBP when utilized as a geopolymer precursor. The favorable mechanical characteristics exhibited by fly ash-GGBFS-WCBP-based geopolymer binder emphasize the importance of assessing its sustainability alongside its technical viability. The study employed life cycle analysis (LCA), following ISO 14040-44 standards, and using the Simapro software, to evaluate the environmental implications of the use of WCBP-based geopolymer mixtures. Human toxicity emerged as the primary impact. Moreover, the analysis of life cycle costs highlighted key financial factors, with around 65-70% attributed to alkaline activators of the total cost. The production of alkaline activators was identified as a critical point for both environmental impact and economic considerations due to energy consumption. While WCBP-rich samples exhibit a 1.7-0.7% higher environmental impact compared to the control mix (CM), their high mechanical strength and cost-effectiveness make them technologically and economically efficient geopolymer mixes. In conclusion, the portfolio analysis for techno-eco-efficiency affirms that mixes containing 40%, 30%, and 20% WCBP are more efficient than those using 10% and 0% WCBP, respectively.

Artificial intelligence (AI) has found extensive applications in the sustainability domain. The municipal solid waste incineration (MSWI) process can achieve waste-to-energy (WTE) goals through the assistance of automation and information technologies. In theory, AI can facilitate the intelligent operation of the MSWI process, simultaneously achieving low pollution emissions and high production efficiency. This study provides an overview of AI applications in the MSWI process. Addressing fundamental challenges, the optimal control of the MSWI process is categorized into four aspects: modeling, control, optimization, and maintenance. Subsequently, this study conducts a detailed analysis and discussion of AI applications in each of these technological domains. In conclusion, this paper outlines the future research directions and provides an outlook on the fundamental issues pertaining to AI applications in the optimal control of the MSWI process.

Electronic waste (e-waste), characterized by the widespread disposal of electronic devices, shows a growing environmental challenge. In this study, we explore the electrocatalytic potential of gold nanoparticles supported on Vulcan obtained from e-waste for their application as electrocatalysts for the methanol oxidation reaction in alkaline media. Gold nanoparticles are synthesized from gold coatings recovered from Intel Pentium 4 processor pins, highlighting their sustainability as electrocatalyst precursors. Comprehensive characterization, including UV-Vis spectroscopy, transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray dif-fraction, is performed to assess the electrocatalyst's structural properties. Electrochemical evalu-ation is carried out in 0.5 M KOH electrolyte employing the rotating disk electrode technique, us-ing cyclic voltammetry for the study of methanol oxidation. Remarkably, the gold nanoparticles show electrocatalytic activity on par with commercially synthesized counterparts, demonstrating the feasibility of this approach for sustainable electrocatalyst production. Thus, this research opens new routes for utilizing e-waste as a source of valuable catalyst materials, addressing en-vironmental and technological challenges in the field of alkaline fuel cells.

The predominant management approach for municipal solid waste (MSW) remains disposal, given significant increases in generation and disposal rates of MSW in recent decades. In addition to the well-documented carbon emissions from disposal sites, these sites accumulate numerous elements, the masses of which are substantial globally yet inadequately quantified. The unique combinations of waste constituents, elements, diverse environments, and confined spaces in disposal sites create distinct biogeochemical conditions, setting them apart from any other infrastructure or geological feature on Earth. This review first presents a global summary of the cumulative masses and disposal rates of MSW constituents and associated elements. The five dominant transformation and transport processes influencing disposed elements are examined: biochemical degradation, physicochemical transformation, gas migration, leachate migration, and solid spillage. The magnitudes and rates of the processes corresponding to major disposed elements, including carbon, nitrogen, sulfur, chlorine, and several metals, are systematically summarized. We examine and quantify the potential environmental impacts and health risks associated with element transformation and transport. We also explore the existing knowledge and techniques for resource recovery and site remediation of disposal sites. The distilled compilation of measurements and insights herein serves as a valuable primer for researchers, practitioners, and decision-makers involved in MSW management.

This research explores the depolymerization of waste polymethyl methacrylate (PMMAW) from dental material in fixed-bed semi-batch reactors, focusing on three production scales: laboratory, technical, and pilot. The study investigates the thermal degradation mechanism and kinetics of PMMAW through thermogravimetric (TG) and differential scanning calorimetry (DSC) analyses, revealing a two-step degradation process. The heat flow during PMMAW decomposition is measured by DSC, providing essential parameters for designing pyrolysis processes. The results demonstrate the potential of DSC for energetic analysis and process design, with attention to standardization challenges. Material balance analysis across the production scales reveals a temperature gradient across the fixed bed negatively impacting liquid yield and methyl methacrylate (MMA) concentration. Reactor load and power load variables are introduced, demonstrating decreased temperature with increased process scale. The study identifies the influence of temperature on MMA concentration in the liquid fraction, emphasizing the importance of controlling temperature for efficient depolymerization. Furthermore, the research highlights the formation of aromatic hydrocarbons from the remaining char, indicating a shift in liquid composition during the depolymerization process. The study concludes that lower temperatures below 450 °C favor liquid fractions rich in MMA, suggesting the benefits of lower temperatures and slower heating rates in semi-batch depolymerization. The findings contribute to a novel approach in analyzing pyrolysis processes, emphasizing reactor design and economic considerations for recycling viability. Future research aims to refine and standardize the analysis and design protocols for pyrolysis and similar processes.

Clothing consumers mostly purchase, use, and dispose of clothing products in a linear business model. This approach pollutes the environment and causes economic and social crises in the ecosystems. This study evaluates the amount of generated postconsumer clothing waste (PCCW) and proposes recycling as a sustainable waste management approach. Data were collected to understand disposal behavior of consumers with 474 respondents selected from households in Bahir Dar city. The findings show that all the determinant factors on the PCCW generation level except religion were significant. The most frequently disposed type of clothing waste is jeans-trouser (51%). The CEBM was used to develop alternative products from a jeans-based clothing waste. The jean's fiber and fabric-reinforced composite materials were developed using unsaturated polyester resin as a sustainable way of PCCW management strategy. The shredded form fiber-reinforced composite was found to have a smoother surface than that of the chopped or cut fabric-reinforced composite. The product was characterized by physical and mechanical properties. The study can be further extended to the scope of the entire consumers in Ethiopia and alternative recyclable products can be studied.

The construction sector is considered as a major consumer of virgin materials and contributor to waste generation. Therefore, it is essential to rethink current waste management practices, for example, by applying circular economy principles to building demolition, such as deconstruction. Deconstruction involves dismantling a building with the aim of maintaining the highest possible value for its materials and maximize their recovery potential. This study aims to guide the construction sector towards deconstruction to support its efforts to transform itself toward a more sustainable industry. It focuses on a regional case study in the province of Québec (Canada) presenting five buildings to be deconstructed. First, the study presents the outcomes of our analysis of the current situation. Second, it identifies the issues and obstacles encountered and proposes avenues to improve the current process based on solutions identified in the literature and the recommendations of the manager, the contractor involved in the deconstruction process, as well as experts in the construction industry. Finally, it proposes an improved deconstruction process. Our research approach is inspired from Lean thinking and follows Action Research methodology.

In this paper, a 100CMM regenerative thermal oxidizer (RTO) system based on a high heating device for low-emission combustion is implemented at a volatile organic compound (VOCs) gas generation workplace. Existing RTO has a structure that repeats the inflow and discharge of VOCs gas into a cylindrical drum-type rotating disk and has excellent energy efficiency with a heat recovery rate of 95% or more. However, when used for a long time, there is a problem that rotation stops or explodes due to the discharge of pollutants due to dust and thermal expansion due to high temperature of 800℃. To overcome this, a RTO based on a high heating device was developed to reduce low-emission combustion emissions and energy use. Through 177 hours of demonstration time, the oxidation efficiency of VOCs was 97.87%; the waste heat recovery rate was reduced by 95.78%, the fuel consumption was reduced by 21.95%, and the nitrogen oxide concentration was 3.9 ppm

In response to the growing need for efficient energy conversion technologies, this pa-per introduces an innovative Tubular Thermoelectric Generator (TTEG), specifically de-signed for high-efficiency conversion of waste heat into electrical energy. Unlike conven-tional flat plate thermoelectric generators (FTEGs), the TTEG incorporates full-ring ther-moelectric elements within a tubular layout, offering a novel approach to thermal energy recovery from fluid-based systems. This design significantly enhances the heat transfer capabilities, thereby improving the efficiency of energy conversion. Comprehensive simulations and analyses form the core of this study, where the per-formance of the TTEG is rigorously compared with traditional FTEGs. These comparisons highlight the advantages of the tubular design in terms of energy conversion efficiency and practical applicability in various scenarios. The findings reveal that the TTEG not only outperforms its flat plate counterparts but also presents a scalable and adaptable so-lution for waste heat recovery in a wide range of industrial and automotive applications. This research contributes to the field of energy science and technology by presenting a detailed experimental setup, complete with reproducible procedures and results. It opens new pathways for the development of more sustainable and efficient energy conversion systems, aligning with the goal of harnessing renewable and sustainable energy sources. The potential applications of this technology in enhancing energy efficiency and reducing environmental impact are vast, making it a significant step forward in the quest for clean and sustainable energy solutions.

Global food waste has a huge impact on the environment, as it is a source of greenhouse gas (GHG) emissions and wasted natural resources. Across the world, over 30% of food is lost or wasted each year. Aside from this, food industry, as well, is one of the biggest sources of agro-industrial waste and by-products, which can be valorized and used for different purposes. Such waste is a good source of bioactive organic compounds which can be extracted without al-tering their properties, where deep eutectic solvents (DESs) can serve as green solvents and excel-lent replacement for volatile organic solvents. Isolated compounds can be used in innovative food production, chemical production, cosmetics and other industries. DESs have attracted extraordi-nary attention due to their advantages such as environmental friendliness, availability and easy preparation, easy handling and utilization of non-toxic components for their formation. Due to those properties, they are a greener alternative to classic organic solvents for many processes, in-cluding extractions. In this paper, we review the utilization of deep eutectic solvents as potential green media for the extraction of organic compounds such as polyphenols, carbohydrates, pro-teins, alkaloids from by-products of the food industry and agro-industrial-waste.

The size of the population and the need for residential spaces are increasing. One possible solution is to add new floors to existing buildings. The positive aspects of such a solution with respect to its socio-economic impact and impact on the environment is that large amounts of carbon dioxide release will be avoided, waste and its treatment will be reduced, and agricultural land and green spaces will be preserved. However, adding floors to existing structures might be structurally challenging, especially in terms of the behavior under seismic actions. This paper presents a numerical study of a reinforced concrete frame in an old building to which new floors are subsequently added. The analysis shows that the frame does not behave as a whole with the old part of the structure, nor does it behave the same as if it were made with rigid joints compared to additional ones connected using hinge joints. The change from the corner (knee) joint to the external joint has its own effect on the distribution of internal forces in the structure as a whole and in the joint in particular.

Printed circuit boards (PCBs) make up 3 to 5% of all electronic waste. The metal content of spent PCBs can reach 40%. They usually contain valuable metals - Ag, Au, Pd, as well as other metals such as Cu, Sn, Pb, Cd, Cr, Zn, Ni and Mn. However metallic part of whole PCB is 40-60% including Cu layers between the fiberglass-polymer layers. The paper describes economics of the the valuable metals (Ag, Au, Pd) containing concentrate preparation from raw PCB. Considered the influence of pre-treatment method of PCB before the extraction of valuable metals on the extraction self-cost change. The disintegration method is based on the high-energy impact of the particles of the material to be ground, thus causing the separation of the metallic components of the PCB. In the course of the work, single and double direct grinding by the method of disintegration was studied. For the calculation the test batch 10’000 kg of two types of PCB were taken for estimation of the self costs and potential profit in case of complete valuable metals (Ag, Au, Pd) plus Cu extraction. Is shown that from 10’000 kg of studied PCB is possible to obtain 1144 and 1644 kg of metal-rich concentrate, which further should be subjected to electro-hydrochlorination for metals leaching. The main findings shows, that despite of high content of Cu in studied PCB, the commercial value is insignificant in total income from the Ag, Au and Pd sale. Was established correlation of the self-cost decrease after separative disintegration of PCB by metal content increase (by specific metals such as Au, Ag, Pd and also Cu) with the metal potential yield after extraction.

Annotation. The experience of using coal flotation waste (CFW) as a weakly exothermic insulating backfill for insulating the head part of forging dead-melted steel ingots is presented.It has been shown that when using weakly exothermic fills based on single-component fills in the form of CFW, it is possible to reduce the chemical heterogeneity of the ingot by producing a closed shrinkage cavity, which allows halving heat loss and depth of penetration of shrinkage looseness into the body of the ingot, reducing the segregation of impurities, compacting the head part of the ingot and increasing the yield; moreover, the profitable part of the ingot is more dense and less contaminated with nonmetallic inclusions.The studied patterns of the formation of a closed shrinkage cavity with a dense “bridge” in the head part of a dead-melted steel ingot made it possible to develop and implement a technology for casting large forging ingots of sufficiently high quality using weakly exothermic heat-insulating materials based on metallurgical waste (coke screenings, coal flotation waste)

New composite with core-shell structure based on magnesium hydride and finely dispersed aluminum powder with aluminum oxide shell was mechanically synthesized. We used magnesium chips to produce magnesium hydride and aluminum wire after exploitation to produce nano-sized aluminum powder. The beginning of the hydrogen release from composite occurred at the temperature of 117°C. The maximum desorption temperature from the MgH₂-EEWAl composite (10 wt.%) is 336°C compared to pure magnesium hydride – 417°C. The mass content of hydrogen in the composite is 5.5 wt.%. The positive effect of aluminum powder produced by the electric explosion of wires method on reducing the activation energy of desorption was demonstrated. Calculations showed that the activation energy of desorption for the composite is 106±1 kJ/mol, compared with pure magnesium hydride, whose activation energy was 155±2 kJ/mol. The results obtained make it possible to expand the possibility of using magnesium and aluminum waste for hydrogen energy.

The Indorama Eleme Petrochemical Limited (IEPL) is found in the southern part of Nigeria more specifically on the Rivers State southern religion Nigeria. It consists of five distinct units, each of which generates its own unique trash at a rate of around 3115.98 tonnes per year. This study had the goal of concentrating on the management of the processing wastes in order to minimize the negative effects that they have on the environment. It is necessary to have an understanding of the number, nature, and make-up of IEPL's industrial wastes in order to effectively manage and regulate the development of waste there. As a result, we decided to collect data through the use of questionnaires. The classification of industrial wastes was accomplished by doing a comparative study and synthesis of research that were relevant to the management of petrochemical waste. Because an individual coding system is required for the integrated management of industrial waste, we gave each type of trash a code that consists of thirteen digits. The primary components of trash were catalysts (9.58 percent), metallic materials (7.62 percent), plastic barrels (35.77 percent), coke (12.66 percent), wood (4.47%), oil (4.15%), glass (0.028 percent), cooling tower packaging (6.7 percent), and other material (18.83 percent). According to the findings of the investigation into the physical qualities of the wastes, only 11.81% of these residues were liquid, while 88.19% were solid. The current handling of these wastes has been experiencing significant difficulties as of late. garbage management at IEPL was particularly challenging due to the wide variety of wastes produced there and the dangerous nature of the wastes themselves (88.19% of garbage was hazardous waste). Recycling and reuse of garbage may have been the greatest decision in some situations; yet, incineration and disposal of waste are also necessary options.

In this study, the effects of food waste (FW) compost, vermicompost, and chemical fertilizers on the growth of organic red radish and soil quality are investigated to promote sustainable agriculture. Utilizing a comparative approach, it assesses the impacts of these fertilizers on various plant growth metrics and soil characteristics, highlighting the potential of converting FW into nutrient-rich amendments as a sustainable alternative to chemical fertilizers. The results indicate a significant variation in fresh weight among different treatments. For example, the FV 25% treatment demonstrated a relatively high mean fresh weight of 7.9664, while the CO 50% treatment yielded a much lower mean fresh weight of 0.2589. These numbers underscore the potential efficacy of specific FW treatments in enhancing plant growth, with VC 50% and FV 25% showing considerable promise in increasing crop yield. The study concludes that FW compost and vermicompost significantly enhance plant growth and soil quality, advocating for their use as sustainable and environmentally friendly alternatives to chemical fertilizers. The findings emphasize the importance of selecting appropriate fertilizer types and concentrations to optimize agricultural productivity and environmental sustainability, supporting the incorporation of FW into agricultural systems as a beneficial resource.

The increasing importance of batteries in the 21st century and the challenges posed by the anticipated growth in end-of-life batteries, particularly in Europe, are addressed. Projections indicate a significant increase in battery waste, with a specific focus on the recycling of black mass (BM)—a complex and hazardous byproduct of the battery recycling process. The research employs the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) methodology to systematically analyze the hazardousness of BM derived from various types of batteries. The findings reveal the inherently hazardous nature of BM, classifying it under multiple hazardous properties (HPs) according to European regulations. The urgent need for a definitive legislative classification of the hazardousness of BM is emphasized, and the potential of innovative technologies and strategies to improve recycling performance while mitigating risks is highlighted. The research significantly contributes to understanding the complexities of BM recycling, providing a foundation for future advancements in this area and emphasizing the need for further exploration and economic feasibility analysis of recycling technologies.

In the last ten years, plasma waste treatment has gained increasing prominence as a technology in response to growing challenges in waste disposal and the recognition of opportunities for generating valuable by-products. The efficiency and outcomes of this process are intricately linked to the characteristics of the plasma involved, such as plasma enthalpy and heat flux. We employed an experimental radio frequency inductively coupled plasma (RF-ICP) torch operating at atmospheric pressure to generate plasma. Utilizing optical emission spectroscopy (OES), we measured plasma parameters, specifically the effective electron temperature (Teff) and plasma density (ne), while varying argon gas flow rates and RF powers. Our investigations revealed that both flow rate and RF power exert significant control over plasma parameters, and we observed an unusual phenomenon within this range of discharge pressures. Consequently, both the plasma's enthalpy and the heat flux it generates are influenced by variations in both flow rate and RF power.

The construction of reinforced concrete (RC) structures inevitably consumes an excessive number of rebars, leading to significant cutting waste and carbon emissions. Extensive research has been conducted to minimize this issue and its consequences; however, these methods consistently consume a substantial number of rebars. This includes a previous study that utilizes the lap splice position optimization and special-length rebar concept without considering the lapping zone regulation. Moreover, conventional lap splices pose inherent drawbacks that could jeopardize the structural integrity of RC members. In contrast, mechanical couplers eliminate the need for rebar lapping, effectively reducing rebar consumption. This research aims to evaluate the impact of an integrated mechanical coupler and special-length-priority minimization algorithm on the reduction in rebar consumption and cutting waste in RC columns, achieving near-zero cutting waste. To validate the effectiveness of the proposed algorithm, it was applied to the column rebars of an RC building. The results revealed a significant reduction in ordered rebar consumption by 18.25%, accompanied by substantial reductions in cutting waste (8.93%), carbon emissions (12.99%), and total costs (10.81%) compared with a previous study. The outcomes provide the industry with insights into further reducing rebar consumption and its related consequences. Applying the proposed algorithm to various construction projects will further amplify the corresponding benefits.

The treatment, disposal, and resource utilization of waste mud are challenges for engineering construction. This study investigates the road performance of waste mud–solidified soil and reveals the mechanism of how solidifying materials influence the strength and deformation characteristics of waste mud. Waste mud, collected from a highway reconstruction project, was mixed with ordinary Portland cement as a solidifying material. Unconfined compressive strength tests, consolidated undrained triaxial shear tests, resonant column tests, and consolidation compression tests were conducted to evaluate the solidification effect. The test results show that with an increase in cement content from 5% to 9%, the unconfined compressive strength of the waste mud–solidified soil increased by over 100%, the curing time was extended from 3 days to 28 days, and the unconfined compressive strength increased by approximately 70%. However, an increase in initial water content from 40% to 60% reduced the unconfined compressive strength by 50%. With the increase of cement content from 5% to 9%, the cohesion and friction angles increased by approximately 78% and 24%, respectively. The initial shear modulus under dynamic shear increased by approximately 38% and the shear strain corresponding to a damping ratio decay to 70% of the initial shear modulus decreased by nearly 11%. The compression coefficient decreased by approximately 55%. Scanning electron microscopy and X-ray diffraction tests showed that a higher cement content led to the formation of more hydration reaction products, especially an increase in the content of AlPO4. The bonding material between soil particles significantly increased, exerting a bonding and filling effect on soil particles and firmly adhering them together. Consequently, the strength of the waste mud–solidified soil increased significantly while its compressibility decreased.

The influence of aluminosilicate pozzolanic waste, specifically spent fluid catalytic cracking catalyst (FCCW) and metakaolin waste (MK) from expanded glass industry, on the properties of hardened Portland cement paste were analysed. The study involved replacing part of cement with FCCW and MK and observing their impact on hydration, microstructure, density and compressive strength of hardened cement paste. Various analysis methods were employed, including X-ray diffraction (XRD), thermogravimetric analysis (TG), and scanning electron microscopy (SEM), to understand the changes in the structure of hardened cement paste during hydration. The findings revealed that FCCW tends to accelerate cement hydration process due to its high surface area and pozzolanic activity. Notably, the formation of portlandite crystals was observed on FCCW particle surfaces in a specific direction. These crystals appeared smaller and developed in different directions in compositions containing a composite binder with mixture of FCCW and MK in a ratio 1:1. This could be influenced by pozzolanic reactions activated by fine particles of MK and the formation of calcium silicate hydrates (CSH) and calcium alumino silicate hydrates (CASH) in the presence of portlandite. XRD and TG results indicated that the specimens containing a composite binder exhibited the least amount of portlandite. The compressive strength of these specimens increased compared to control specimens, although the amount of cement was 9% lower.

This paper aims to propose improvements for plastic waste management in Salvador – the Brazilian third most populated metropolis – via Partial Least Squares Structural Equation Modeling (PLS-SEM). All indicators, constructs, and hypotheses regarding collection, sorting, recycling, and disposal in the proposed PLS model were derived from the literature review, and the dependence of the performance construct on efficiency, effectiveness, municipality's socioeconomic aspects and municipality infrastructure is evaluated. Academic and practitioner publics were surveyed, and after analysis in both SmartPLS and RStudio software, suggestions for improvement regarding plastics recycling rate, market maturity, and infrastructural aspects for optimized reverse logistics were made. Since almost double the minimum number of respondents answered the survey questionnaire and the PLS-SEM statistics showed that the modeling presents consistency, the discussion is relevant. The model can and will evolve, but examples of suggested improvement are the installation of Deposit-Return Systems (DRS) in parks, streets, and avenues for increasing selective collection and the direct purchasing of waste from residents by municipal administration, compensating them with vouchers for food. The model can be a basis for other cities worldwide sharing analogous characteristics. By considering it, organizations can contribute to both reduced Greenhouse Gas (GHG) emissions and reduced terrestrial pollution.

Recent years have experienced an increase in construction and demolition waste (C&DW), which is the most significant solid waste stream. C&DW is contributing to exceeding all planetary boundaries and presents a range of other issues. In order to better understand the existing research on C&DW, a global bibliographic analysis was undertaken through seven groups of keyword searches and the results visualised using VOCviewer. The results show that C&DW receives only a modest research attention compared to other areas of waste, and this is despite an exponential increase in C&DW research since 2016. The analyses also show that concrete is the most researched material in terms of C&DW, and that reuse, recycling, and circular economy are so far attracting only proportionally modest research attention. This signals a need for further acceleration of the C&DW research, and specifically for more research on reuse, recycling, and circular economy for materials other than concrete.

Aquaculture by-products can be compromised an important liming material of increasing soil pH and soil fertility. The aim of this research was to assess the effect of mussel shells on soil pH, on organic matter and on soil nutrients. In this study a pot experiment was carried out at the De-partment of Ichthyology and Aquatic Environment (University of Thessaly, Greece). A acidic soil (pH 4.26) amended with 6 different proportions of mussel shell (0.0, 0.1, 0.3, 0.5, 1, 3 and 6%) in two different grain sizes (Fine powder (>1 mm) and Coarse powder (1-2 mm)), resulting in 13 treatments. According to the results, it was observed that pH, organic matter, Available P and Exchangeable K increased. Specifically, the highest pH values observed at 6% rate. Available P and Exchangeable K achieved the highest content at 6% Fine powder treatment, 46.2 and 190.1 mg kg-1, respectively. Similarly, organic matter had the highest value in 6% Fine powder pots (2.27%). Moreover, Total N concentration varied from 0.11 to 0.14 but no statistically significant different was noticed between the treatments. In conclusion, mussel shells can compose a promising liming material in the agriculture section.

Printed Circuit Boards (PCBs) are essential to most electronic devices. Digitalization and upgradation of gadget generates lots of PCB-containing electronic waste. Conserving resources and protecting the environment requires recycling such e-waste. The present paper is focused on the recovery of metals from PCBs by physical pretreatment and hydrometallurgical processes. Initially, the waste PCBs were pre-treated to separate metallic and non-metallic fractions. The metallic concentrate was leached using nitric acid (strong oxidative agent) for dissolution of metals. The system was fully jacketed with scrubber and condenser so that no emission of toxic gases to the environment. The process parameters viz. effect of acid concentration, pulp density, temperature, time, etc. were optimized and the obtained data were scientifically validated. Kinetics leaching fitted well with the Shrinking core model, XB = kc.t for Cu, (1-(1-XB)1/2) for Ni and 1-3(1-XB)2/3 + 2(1-XB) for Pb. The optimized conditions derived from these studies will be useful for recovery of metals from waste PCBs, and tin left in the residue could be further treated for the purpose of safe disposal or the utilization in an environmentally friendly manner. The developed process provides environmental benefits and has potential to be commercialized after scale-up studies.

Information and telecommunications technology (ITT) have expanded into many aspects of modern life and have positively affected human life even in the most remote areas of developing countries. The rapid growth in ITT has led to an improvement in the capacity of computers but simultaneously to a decrease in the product’s lifetime as a result of which increasingly large quantities of e-waste are generated annually. It contains hazardous components that if it is not properly managed, can have adverse environmental and health effects. The management of e-waste poses significant challenges in developing countries. Due to the lack of adequate infrastructure, e-waste is burned or dumped in open areas. Informal and inefficient recycling practices are generally employed which further exacerbate pollution and health risks. So, the implementation of e-waste management, adequate recycling, and waste disposal facilities have become crucial concerns. This article reviews the concept of e-waste generation, challenges, disposal, and its impact on human health & environment in detail.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

The recycling of common soda-lime glass (SLG) is far from being complete, since the material may contain small polymeric, metallic and ceramic contaminations. This has a negative impact on the quality of new glass articles prepared via re-melting. Alternatively, the full reuse of contaminated cullets could be achieved by low-temperature consolidation into geopolymer-like materials. SLG powders, used either as received or pre-washed in acid solution, were added to a sodium aluminate solution at the room temperature for 3 h, under low-speed mechanical stirring. Microporous semi-crystalline monoliths were formed by the casting of suspensions in plastic molds and cured at 75°C overnight. The monoliths featured hydrosodalite as the main crystalline phase for as received SLG and LTA zeolite in the case of pre-washed SLG. The mechanical properties compared well with those of cementitious materials. Moreover, by addition of coarse glass particles as fillers, the methodology successfully yielded Venetian terrazzo-like samples, which could lead to significant material and energy savings in their manufacture. The proposed approach could also be extended to other difficult-to-reuse glass formulations and provide attractive and versatile up-cycled materials.

Within the past few decades, thousands of experiments have been performed to characterize waste and biomass to estimate the bioenergy potential and product identification. There is a need to develop an integrated process model based on experimental literature, and simulation to obtain suitable products. In this study municipal solid waste (MSW) characterization and integrated process model have been developed to optimize final products in a reactor system. The process model has two modes R&D and reactor control (RC) to obtain suitable products including bio-oil, char, and gases. A database was integrated based on thermokinetics, machine learning and simulation models to optimize product efficiency. The experimental data includes thermogravimetric analysis, Fourier transform Infrared Spectroscopy, Gas chromatography, and Mass spectrometry, which are linked with pyrolysis experimental setup. Feedstock-product mapping models were incorporated into the database along with the temperature, heating rates, elemental analysis, and final product concentration, which are utilized for pyrolysis reactor setup. Product feasibility is conducted based on lifecycle cost, affordability, and product efficiency. The present work will bridge the gap between experimental study and decision making based on obtained products at several experimental conditions around the world.

SDG target 12.3 calls for halving food waste at retail, food service, and household by 2030. The food waste index for this purpose includes parts attached to food that are usually removed intentionally ("unavoidable food waste") and allows counting the conversion to animal feed and utilisation as biomaterial as means of reduction. In Japan, the "Food Waste Recycling Law" which has been in effect since 2001, promotes the recycling of food waste generated from businesses, designating feed conversion as top priority. On the other hand, based on the more recent "Food Loss Reduction Promotion Act" of 2019, the government is currently promoting the reduction of avoidable food waste, as to meet the SDG target. Based on statistical sources and interviews with Ministry officers, this paper explains the history and achievements of Japan's 23-year policy based on the Food Recycling Law, as well as the tension between the two legislations.

Plant waste biomass is the most abundant renewable energy resource on Earth. The main problem of utilising this biomass in anaerobic digestion is the long and costly stage of degrading its complex structure into simple compounds. A promising solution to this problem are fungi of the Trichoderma genus, which show a high capacity to produce hydrolytic enzymes capable of degrading lignocellulosic biomass. This article discusses the structure of plant waste biomass and the problems resulting from its structure in the digestion process. It presents the methods of pre-treatment of lignocellulose with a particular focus on biological solutions. Based on the latest research findings, key parameters related to the application of Trichoderma sp. as a pre-treatment method are discussed. In addition, the possibility of using the digestate from agricultural biogas plants as a carrier for the multiplication of the Trichoderma sp. fungi, which are widely used in many industries, was discussed.

Quarry waste fines and eggshells are unavoidable wastes which relentlessly contribute to environmental load and pollution. Although a number of studies have suggested various methods for recycling, these wastes remain underutilized due to some technical constraints. In addition, no study has yet been explored on the possibility of combining quarry waste fines (QWF) and eggshell powder (ESP) for tobermorite synthesis. Tobermorite is the main component which primarily provides strength to the autoclaved aerated concrete products. For this purpose, this study seeks to evaluate the potential of QWF- ESP mix at 10%, 15% and 20% amounts of cement, respectively. The XRF, XRD, and TGA–DTA techniques were used to characterize the waste materials while physical and mechanical property tests and XRD analysis were performed on the autoclaved samples. It was found that QWF contains 53.77% SiO2, while ESP contains 97.8% CaO which are key components for tobermorite synthesis. This study also revealed that the mixture with only 10% cement has the highest compressive strength among the QWF-ESP samples. Furthermore, the formation of tobermorite in the samples was confirmed through XRD analysis. Hence, the hydrothermal curing of QWF –ESP can be further developed to produce functional tobermorite – bearing materials.

Natural fibers have attracted increasing interest as an alternative to produce environmentally friendly and sustainable materials. Particularly, hemp fibers have revealed to be widely used in various industrial applications due to their extremely unique properties. However, hemp can generate a large amount of agro-waste, and results in an attractive source of biopolymers for the development of low-cost materials in alternative to the raw materials and conventional petroleum-based plastics. In addition, deep eutectic solvents (DESs), a new type of truly green solvents, have been tested to remove gums, lignin, and other non-cellulosic components from hemp fibers. Reusing these components dissolved into the DESs to fabricate new materials directly by electrospinning is a very attractive but still unexplored endeavor. Thus, this innovative research to venture new upcycling pathways is focused on the fabrication of composite nanofibers by electrospinning of a gel-based blend of Poly(vinyl alcohol) (PVA) and hemp agro-waste (HW) dissolved into choline chloride (ChCl) : Glycerol (1:2) and ChCl : Urea (1:2) DES mixtures. The results obtained revealed that the produced nanofibers displayed uniform appearance with diameters ranging from 257.72 ± 65.63 nm to 380.78 ± 133.98 nm. In addition, the mechanical properties of the electro-spun composite nanofibers produced from the gel-based blends of HW dissolved in DESs and PVA (HW-DESs_PVA) were found to be superior, resulting in an enhanced tensile strength and Young’s modulus. Furthermore, the incorporation of HW into the nanofibers was able to provide bioactive antioxidant and antibacterial properties. Overall, this study demonstrated a promising, more sustainable, and eco-friendly way to produce electrospun composite nanofibers using HW in a circular economy perspective.

Enzymes are biological molecules produced by living entities for carrying out biological processes. The application of enzymes for waste treatment has been gaining pace commercially to solve concerns related to agricultural residues, wastewater, replacement of synthetic processes with natural ones, etc. The application of enzymes for waste management has been an environmentally reliable and sustainable process. Treatment of waste with enzymes such as xylanase, proteases, hydrolases, cellulose, peroxidases, chitinases, laccases, etc. has been studied to be effective. These enzymes act upon the waste products and transform them into biodegradable forms that can be recycled, reused and converted to value-added products. They have wide applications and utility as it has been an effective approach, economically cheaper and sustainable techniques. Application of such enzymes for waste management would be beneficial for reducing the quantity of waste, diminishing the negative effects of waste and pollution on the environment, and would be beneficial in bio-converting the waste products into alternate sources of energy. The current chapter focuses on different types of enzymes, their applications for waste management, and their limitations. This chapter also emphasizes the usage of some prominent microorganisms, their secreted enzymes and their proposed mechanisms of action involved with the degradation of the waste products.

To ensure sustainable production and consumption in the agricultural sector, it is necessary to assess the contribution of each element of the nexus in the agricultural production chain. The aim of this study is to make a quantitative and qualitative analysis of the contributions of each element of the energy, water, waste and land nexus to agricultural products. A composite method approach combining aspects based on input-output model, Location Quotient (LQ) as well as competitive position is adopted. A database of nexus elements over a period from 2009 to 2018 is used for Cameroon, with ten regions considered. The results show proportions of around 0.42% energy, 67.88% water withdrawal, 11.91% harvested area, 97.81% waste for agricultural products. The geolocation of harvested areas shows that the largest portion is in the far north (1,373,829 ha) and the smallest in Adamawa (224,038 ha). Maximum production is in the central region (4,334,095 tons) and minimum in the Adamawa region (915,841 tons). The central, littoral and west regions are more representative of agricultural products. The analysis of the competitive position of agricultural products contributes to a better orientation of national strategies for agricultural sustainability according to existing potentials.

E-waste is considered the fastest-growing global waste stream and has become an emerging environmental challenge. The widespread usage of digital devices has generated a large amount of e-waste. According to the Ministry of Commerce, India annually generates ~14.5 lakh metric tons of e-waste and recycles only ~5 % of e-waste. Annually, the global production of e-waste has been expected to increase by 4–5 %. Advancements in IT and communication divisions have improved the usage of electronic equipment. Heavy metals such as (Pb), mercury (Hg), arsenic (As), tin (Sn), and organic chemicals such as polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs), polybrominated biphenyls (PBBs), polybrominated dibenzo-p-dioxins (PBDDs), polybrominated diphenyl ethers (PBDEs) are subsequently released from e-wastes and contaminates soil and water sources. These toxic compounds are hazardous to human health and the environment. They are capable of entering various biological systems and causing alterations in respiratory functions of the lungs, DNA damage, impaired functioning of the thyroid, and increased risk of chronic diseases such as cancer and cardiovascular ailments. Such concerns raise the quintessential need to manage e-waste to prevent future hazards. This manuscript critically reviews the sources, health and environmental impact, disposal techniques, recycling, and regulation of e-waste.

Slags and ashes generated in thermal waste treatment facilities require proper management. In line with the principles of the circular economy, new, more economical and ecological possibilities for utilizing these substances are sought. These waste materials exhibit characteristics similar to rocks in many aspects. This study focuses on analyzing the similarities and differences between nine selected rocks and three samples of slags and ashes obtained from municipal waste incineration. The main research device used was a polarizing microscope, using reflected, transmitted and fluorescent light. Additionally, low-pressure gas adsorption equipment, as well as helium and quasi-liquid pycnometers, were used for complementary analysis. The parameters analyzed mainly covered broadly defined petrographic properties of rocks and slags, with a particular emphasis on porosity, porous structure and the spatial distribution of pores and fractures. The conducted analyses confirmed a significant similarity between slags and ashes and clastic sedimentary rocks such as sandstones and mudstones. The research results underscore the importance of petrographic microscopic studies for analyzing materials other than rocks. They also allow for exploring applications for slags and ashes in areas traditionally reserved for natural rock resources. The findings also indicate the necessity of using methods other than microscopic ones to describe the pore space of rocks. The lower measurement range of the optical microscope is limited to approximately 1 μm, covering only macropores. Other methods extend this characteristic to micro- and mesopores. Therefore, a combination of different methods is often employed to obtain a more comprehensive characterization of rock porosity.

Although the potential of natural minerals for purification of liquid radioactive wastes (LRW) from radionuclides has been widely studied, the use of hybrid polymer composites made of zeolite is still rather scarce. This article reports on the preparation of zeolite based hybride polymer composites using the in-situ polymerization technique in the body of mineral matrix and its intercalated with copper ferrocyanide (CuFC) forms. This hybrid polymer composites have shown unique and enhanced properties as compared to the individual mineral. The change in conventional properties of two mixed minerals such as zeolite and bentonite and their intercalated with CuFC forms were probed using technics such as scanning electron microscopy (SEM), X-ray diffraction (XRD), Mossbauer spectroscopy (MS) and FT-IR analysis. The totality of analysis showed a coexistence of intercalated and percolated zeolite phases. The hybrid polymer composites exhibited both adsorption and ion-exchangr properties in removal of radionuclides from LRW.

Municipal Solid Waste Management (MSWM) struggles with significant policy and operational challenges, particularly concerning recyclables collection routes and fleet composition. Within the European Union, phasing out traditional fuel-based vocational vehicles, like garbage trucks, in favor of zero-emission alternatives is mandatory to achieve sustainable development objectives. Integrating electric solid waste collection vehicles into municipal fleets presents challenges due to differences in range, capacity, and noise levels. The emission is even more crucial in the systems where recyclables are collected separately, which requires a greater number of trips to be performed. This study addresses MSWM’s strategic aspect by minimizing the total cost of replacing waste collection vehicles while meeting emission constraints. The Fleet Transition Problem (FTP) was formulated and solved using a MARKAL-based approach. The objective of the FTP and a mixed integer linear program used to solve it is minimizing the overall cost of fleet modernization throughout a multi-phase planning horizon so that the sustainable transition of the fleet can be assured. Computational experiments affirmed the model’s effectiveness in strategizing fleet transition. This research outlines a multi-period model for transitioning to a zero-emission fleet and demonstrates the FTP’s potential for strategic decision-making. Notably, the study observes a consistent reduction in permissible emissions across the planning horizon.

Industries are required to utilize treatment technologies to reduce contaminants in wastewater prior discharge and valorize by-products to increase sustainability and competitiveness. Most acid leaching gypsum purification studies have obviated the treatment of the highly acidic wastewater produced. In this work, acidic wastewater from acid leaching purification of post-consumer gypsum was treated to recover a valuable solid product and reusable water. The main aims of this work were to determine the impact of recirculating acidic and treated wastewaters on the efficiency of the acid leaching purification process and to valorize the impurities in the wastewater. Samples were characterized through X-ray fluorescence and X-ray diffraction. SimaPro 9.5 and ReCiPe 2016 midpoint method were used for the life cycle assessment of three wastewater management approaches. The reuse of the acidic wastewater did not improve the chemical purity of gypsum. Soluble impurities were precipitated at pH 10.5 as a magnesium-rich gypsum that could be commercialized as fertilizer or soil ameliorant. The alkaline treated water was reused for 6 acid leaching purification cycles without impacting the efficiency of the purification process. An acid leaching-neutralization-filtration-precipitation approach demonstrated superior overall environmental performance. Barriers and enabling measures for the implementation of an in-house wastewater treatment were identified.

The global predicament of solid waste generation looms as a mounting crisis, profoundly impacting the world, particularly in developing nations. Each day, the world's population contributes millions of tonnes of municipal solid waste, with projections pointing toward further escalation in the coming years. This surge in waste, predominantly composed of cellulose-rich materials, correlates directly with heightened pollution, a threat that transcends borders and imperils humanity as a whole.To confront this ever-growing issue, cellulase, a potent hydrolytic enzyme capable of digesting cellulose, a chief component of solid waste, is explored as a potential solution. In this study, we harness cellulase enzymes derived from the digestive tracts of both Archachatina marginata and Oryctes rhinoceros larvae, employing them as biodegradation agents for cellulose-based waste materials.The cellulase enzymes are methodically isolated and partially purified via ammonium sulfate precipitation at 65% saturation. Their efficacy in breaking down a variety of waste categories, encompassing kitchen waste, leaves, paper, wood, and industrial waste, is meticulously assessed and benchmarked against carboxymethyl cellulose (CMC), a well-established laboratory substrate. The study also ascertains the specific activity of these enzymes.Spectrophotometric analyses of the cellulase enzymes' actions on the diverse waste materials unveil intriguing results. Archachatina marginata and Oryctes rhinoceros larvae exhibit distinct performance metrics, registering percentage ranges of (11.04% - 28.31%) and (33.69% - 189.11%) on wood waste, (76.52% - 196%) and (108.56% - 567.01%) on paper waste, (78.57% - 148.14%) and (163.33% - 436.76%) on leaf waste, (57.16% - 179.95%) and (63.38% - 457.05%) on kitchen waste, and (59.95% - 77.51%) and (117.26% - 155.23%) on industrial waste, respectively. This study underscores the substantial biodegradation potential inherent in cellulase enzymes from both Oryctes rhinoceros larvae and Archachatina marginata when applied to diverse waste materials. While the rates and impacts of waste degradation vary between these sources, their promising contributions to waste management come into focus, offering sustainable and innovative approaches to tackle the pressing global challenge of solid waste proliferation.

Currently, with the rapid growth of the population, the demand for metals has increased, especially for the manufacture of electronic devices such as cell phones, computer equipment, among others. Once these devices stop working, most are sent to landfills, which represents a danger since these wastes contain metals and other materials that must be properly managed to prevent them from having a negative effect on the environment and the human being. On the other hand, e-waste contains valuable metals such as copper, gold, and silver, the concentration of which in these materials makes it cost-effective to recover. This paper presents a review of the extraction and recovery of valuable metals from electronic waste by hydrometallurgical methods, as well as patents and industrial processes related to the management and treatment of this waste.

The paper presents a thorough examination of the burgeoning field of utilizing manufacturing waste for sustainable energy generation, aligning with the global imperative for resource efficiency and clean energy solutions. With the manufacturing sector being a significant contributor to waste generation, this study explores innovative approaches to transform waste materials into valuable resources, thereby mitigating environmental impacts and contributing to a circular economy. This work critically reviews current trends, emphasizing technological advancements, policy interventions, and market dynamics shaping the manufacturing waste utilization landscape. Noteworthy developments, such as advanced sorting technologies and the integration of digital solutions, are discussed in detail, showcasing their role in enhancing the efficiency of waste management processes. The study outlines future trends in the field, anticipating a shift towards closed-loop systems guided by circular economy principles. This comprehensive review aims to contribute to the discourse on sustainable waste management and energy generation by providing a holistic perspective on the field's current state and offering insights into the future trajectories that will propel manufacturing waste toward a more sustainable and circular future. The synthesis of technological innovation, collaborative efforts, and evolving regulatory frameworks presents a compelling case for the continued exploration of manufacturing waste as a valuable resource in the pursuit of a more sustainable and energy-efficient world.

Humification is a promising strategy to reduce the amount of animal waste generated in agriculture. This makes it possible to accumulate products with artificially obtained humic substances (HS) as analogues of natural HS, usually extracted from fossil sources (coal, peat). The review examines the main characteristics of various biological and physical-chemical methods (composting, anaerobic digestion, pyrolysis, hydrothermal carbonation, acid or alkaline hydrolysis, subcritical water ex-traction) used to form HS in animal waste humification products. A comparative analysis of the humification rates and yields of HS in these processes, the characteristics of artificial HS in products (humification index, polymerization index, degree of aromaticity, etc.) is carried out in connection with the use of certain methods of humification and types of animal waste. The main factors (ad-ditives, process conditions, waste pretreatment, etc.) that can increase the efficiency of humification and the properties of HS resources artificially obtained by various methods are highlighted. A generalizing analysis of the content of chemical elements in artificial HS obtained from various animal husbandry wastes in comparison with natural HS was carried out. Based on the results of the chemical composition analysis, the main trends and preferences regarding the most useful ap-plications of humification products as complex biomimetics are discussed.

There are four categories of medical waste that cannot be mixed as this will cause serious problems such as environmental pollution or infection. In the past, the classification of medical waste often involved a lot of human and material resources to process, with workers at risk of exposure to infectious substances. Therefore, an augmented reality (AR) and artificial intelligence (AI) medical waste classification system and method were developed. This innovative medical waste classification system and method combines AR and AI identification technology to reduce the risk of manual judgment errors by clinical staff when handling medical waste.

The accurate classification of landfill waste diversion plays a critical role in efficient waste management practices. Traditional approaches, such as visual inspection, weighing and volume measurement, and manual sorting, have been widely used but suffer from subjectivity, scalability, and labour requirements. In contrast, machine learning approaches, particularly Convolutional Neural Networks (CNN), have emerged as powerful deep learning models for waste detection and classification. This paper analyses VGG-16, InceptionResNetV2, DenseNet121, Inception V3, and MobileNetV2 models to classify real-life waste when trained on pristine and unadulterated materials, versus samples collected at a landfill site. When training on DiversionNet, the unadulterated material dataset with labels required for landfill modelling, classification accuracy was limited to 49.69% in the real environment. Using real-world samples in the newly formed RealWaste dataset showed that practical applications for deep learning in waste classification is possible, with Inception V3 reaching 89.19% classification accuracy on the full spectrum of labels required for accurate modelling.

Rice cultivation is the main agricultural activity in Asia, and it results in an enormous amount of agricultural waste, that are usually disposed-off by burning, causing serious environmental health and climate problems. Pakistan is the tenth largest producer in the world and the fourth exporter of rice in the world. To date, there are no studies targeting Pakistan’s profile monitoring its contribution in open burning emissions from rice straw waste. This study presents the characterization of PCDD/Fs, PCBs and PAHs emissions from three samples of rice straw collected from the main rice cultivation regions of Pakistan (Punjab, Sindh and Azad Jammu and Kashmir) in relation to the role of metal-based agricultural additives. PCDD/Fs, PCBs and PAHs emissions were quantified using a fixed grid system biomass plant and measuring the macro-pollutants online and sampling the organic micro-pollutants and metals in isokinetic mode, followed by ISO and CEN standards methods. In addition, role of agrochemicals was monitored in terms of metal catalysis resulted in POPs emissions. This study provides the characterization of most relevant group of pollutants (metals, PCDD/Fs, PCBs and PAHs) as a result of agricultural waste combustion. The rice straw samples from AJK showed high values of organochlorine micro-pollutants compared to the values followed by samples from Punjab and Sindh, i.e., respectively, ∑PCDD/F (2594>1493>856 pg/Nm³) and ∑PCB (41>38>30 pg/Nm³). Whereas the organic micro-pollutants ∑PAH, indicators of incomplete combustion (PICs), were recorded high in the samples from Sindh followed by Punjab and AJK. This study supports the idea that the phenomena that lead to the formation of PCDD/F and PCB are influenced not only by poor combustion but also by the presence of metal catalysts or precursors in the burned fuel.

In this study, the objective is to analyze the economic viability of municipal household solid waste (organic matter + paper) for the production of gas, coke and biofuel through the pyrolysis and distillation process. The waste was collected in the city of Belém do Pará-Brazil and pre-treated at UFPA. The analyzed fraction (organic matter + paper) was subjected to pre-treatment of drying, crushing, sieving and was subsequently subjected to proximate characterization and finally pyrolysis of the organic fraction (organic matter + paper) in a fixed bed reactor. Initially, it was necessary to review the literature and with the yields obtained by pyrolysis of the frac-tion, economic feasibility analyzes were carried out. The economic indicators for evaluating the most viable pyrolysis process were: simple payback, discounted payback, net present value (NPV), internal rate of return (IRR), and profitability index (IL). The analysis of the indicators showed the economic viability considering an analysis horizon of 10 years, of materials based on organic material and paper. The break-even point obtained was 0.96 US$/L and the minimum biofuel sales price (MFSP – “Minimum Fuel Sale Price”) obtained in this work was 1.30 US$/L. The sensitivity analysis demonstrated that material costs (organic matter + paper), bio-oil yield, total project investment and electricity, respectively, are the variables that most affect the mini-mum biofuel sales price (MFSP).

In recent years, the use of solid waste fillers to partially replace natural fillers in asphalt mixtures to produce high-performance asphalt mixtures has received widespread attention. However, differences in the material properties of solid waste fillers remain a problem for this recycling method. To address this issue, limestone powder in asphalt mixtures was replaced by three solid waste fillers (steel slag powder, tailings powder and calcium carbide slag powder) in this study. The chemical composition of the fillers was first characterized to assess the homogeneity of the material. Then, AC and SMA asphalt mixtures were designed and produced and characterized for wet stability. The results showed that asphalt mixtures with solid waste fillers were superior to LP asphalt mixtures in terms of resistance to water damage, and steel slag powder showed the best improvement in moisture stability of asphalt mixtures. The optimum substitution of solid waste filler for limestone filler was 25%. In addition, the moisture stability of asphalt mixture with limestone filler was significantly improved with the addition of anti-stripping agents. In contrast, the moisture stability of asphalt mixtures with solid waste filler was slightly improved. Solid waste fillers could be used in asphalt mixtures and have a similar function as the anti-stripping agent. In summary, the use of solid waste fillers to replace mineral fillers in asphalt mixtures is a reliable, value-added, recycling option.

The use of plastic in agriculture has become so omnipresent within the industry that it has acquired it own lexicon to become known as ‘plasticulture’. However, since, compared to other industries the quantities consumed are low, little attention is granted to this waste stream. This is the case both with local and international policies even though it bears a close connection to soil health and therefore is a prerequisite to improve the sustainability of food production processes including food security. Using Malta as a case study, the research utilises quantitative and qualitative tools to identify and quantify the most common types of agricultural plastic waste generated and determines the attitudes of farmers towards a collection and recycling scheme. While it identifies that incineration and ploughing of plastic waste as regular practices, it also ascertains the willingness of farmers to acquire more knowledge about more appropriate methods to dispose of this waste stream thus guiding policy makers towards the need to initiate educational measures for farmers to prevent these harmful practices. Through stakeholder interviews the research highlights that the present lack of data is a major hindrance for policy to take account of this waste stream.

Solid waste management is challenging in many countries, especially developing economies. The impacts of the pandemic continue to be felt and have indicated secondary impacts on waste management. This work draws on data on household solid waste (HSW), healthcare waste (HCW), and recyclables collected in the Rio de Janeiro municipality, analyzed from January 2018 to December 2022. As expected, the collection of HCW in Rio de Janeiro municipality experienced a noticeable increase in 2020 and 2021, with an average of 46.9 tons and 54.3 tons collected, respectively. Notably, 2021 saw a significant 30% increase compared to 2019 (p-value<0.001). No significant difference was observed in recyclables collected from 2018 to 2021. The average recyclable amount was 3,638 and 3,747 tons per month in 2020 and 2021. In contrast, the monthly amount was equal to 4,819.5 tons in 2022, representing an increase higher than 32% compared to previous years (p-value<0.05). Our findings can be used to adapt and improve waste systems to cope with similar emergency scenarios in the future, serving as a template for municipalities with similar challenges.

Any Hospital’s primary goal is to restore human health and save lives through health services provided to patients, but at the same time, hazardous wastes are produced. Inconsistent management of unsafe wastes might cause adverse effects and other issues to workers, the environment and public health. Segregation is considered the critical stage for a successful Healthcare Waste Management. Mixing hazardous waste with non-hazardous waste will be avoided by correctly applying practices at the segregation stage. This study aimed to assess personnel’s knowledge about Infectious Medical Waste and segregation practices used at six wards in Nicosia General Hospital. An analytical cross-sectional study was conducted, and data were collected through a structured self-administered questionnaire. The Statistical Package of Social Science (SPPS) version 25 was used with a minimum statistical significance α=0.05. The study population was nurses, nurse assistants, ward assistants and cleaners working at the study wards. Out of 191 questionnaires, 82 were received, with a response rate of 42.93%. Most participants were female (72%) and nurses (85,4%). Participants had medium to good knowledge about Infectious Medical Waste management and good knowledge regarding segregation practices applied in their ward. Segregation was not carried out as it should have since most participants stated that Infectious Medical Wastes were mixed with non-hazardous waste. Correct answers given by the participants regarding color-coding of different Healthcare Waste categories was 67.5%, and only four answered correctly to all questions. Although participants knew segregation practices and the colour-coding process applied for Healthcare Waste, they didn’t use them satisfactorily. They applied methods regarding segregation without specific training, knowledge and guidance. Due to the issue's importance, training programs must be implemented and performed.