Analysis of 1382 measures of battery State of Health (SoH) from 283 Nissan Leafs (“Leaf/s”), manufactured between 2011 and 2017, has detected a faster rate of decline in this measure of energy-holding capacity for 30 kWh variants. At two years of age, the mean rate of decline of SoH of 30 kWh Leafs was 9.9% per annum (95% uncertainty interval of 8.7% to 11.1%; n = 82). This was around three times the rate of decline of 24 kWh Leafs which at two years averaged 3.1% per annum (95% uncertainty interval of 2.9% to 3.3%; n = 201). For both variants there was evidence for an increasing rate of decline as they aged, although this was much more pronounced in the 30 kWh Leafs. Higher use of rapid DC charging was associated with a small decrease in SoH. Additionally, while 24 kWh cars with greater distances travelled showed a higher SoH, in 30 kWh cars there was a reduction in SoH observed in cars that had travelled further. The 30 kWh Leafs sourced from United Kingdom showed slower initial decline than those from Japan, but the rate of decline was similar at two years of age. Improvements in the battery health diagnostics, continuous monitoring of battery temperatures and state of charge, and verification of a fundamental model of battery health are needed before causes and remedies for the observed decline can be pinpointed. If the high rate of decline in battery capacity that we observed in the first 2.3 years of a 30 kWh Leaf’s lifetime were to continue, the financial and environmental benefits of this model may be significantly eroded. Despite 30 kWh Leafs accounting for only 14% of all light battery electric vehicles registered for use on New Zealand roads at the end of February 2018, there is also the potential for the relatively poor performance of this specific model to undermine electric vehicle uptake more generally unless remedies can be found.

Since the Coronavirus disease (COVID-19) outbreak at the end of 2019, the past two month has seen an acceleration both in and outside China in the R&D of the diagnostics, vaccines and therapeutics for this novel coronavirus. As one of the molecular forces that determine protein structure, electrostatic effects dominate many aspects of protein behaviour and biological function. Thus, incorporating currently available experimental structures related to COVID-19, this article reports a simple python-based analysis tool and a LaTeX-based editing tool to extract and summarize the electrostatic features from experimentally determined structures, to strengthen our understanding of COVID-19's structure and function and to facilitate machine-learning and structure-based computational design of its neutralizing antibodies and/or small molecule(s) as potential therapeutic candidates. Finally, this article puts forward a brief update of the structurally observed electrostatic features of the COVID-19 coronavirus.

Complex systems exhibit critical thresholds at which they transition among alternative phases. Complex systems theory has been applied to analyze disease progression, distinguishing three stages along progression: (i) a normal non-infected state, (ii) a pre-disease state in which the host is infected and responds; therapeutic interventions could still be effective, (iii) an irreversible state, where the system is seriously threatened. The Dynamical Network Biomarker (DNB) theory sought for early-warnings of the transition from health to disease. Such DNBs might range from individual genes to complex structures in transcriptional regulatory or protein-protein interaction networks. Here we revisit transcriptomic data obtained during infection of tobacco plants with tobacco etch potyvirus to identify DNBs signaling the transition from mild/reversible to severe/irreversible disease. We identified genes showing a sudden transition in expression along disease. Some of these genes cluster in modules that show the properties of DNBs. These modules contain both genes known to be involved in response to pathogens (e.g., ADH2, CYP19, ERF1, KAB1, LAP1, MBF1C, PR1, or TPS5) and other genes not previously related to biotic stress responses (e.g., ABCI6, BBX21, NAP1, OSM34, or ZPN1).

The tobacco epidemic is one of the leading public health threats the world has ever faced and public health policy that seeks to limit the problem may not only have to target the price of tobacco but also the initiation stage in a smoker’s life – the adolescent stage. This research contributes to the health economics literature by using a Bayesian hierarchical logistic model, estimated using Hamiltonian Monte Carlo (HMC) methods to empirically identify what drives the intentions to quit smoking among adolescent smokers in Zambia. Results suggest that among the junior secondary school-going adolescent smokers in Zambia, about 63% have plans to quit smoking. We find socio-demographic characteristics and several tobacco-smoking-related factors as the main drivers of adolescent smokers’ plans to quit smoking. Most importantly, we provide insights that could be useful to help adolescent smokers realize their quitting plans.

With the increase of the Artificial Neural Network (ANN), machine learning has taken a forceful twist in recent times. One of the most spectacular kinds of ANN design is the Convolutional Neural Network (CNN). The Convolutional Neural Network (CNN) is a technology that mixes artificial neural networks and up to date deep learning strategies. In deep learning, Convolutional Neural Network is at the center of spectacular advances. This artificial neural network has been applied to several image recognition tasks for decades and attracted the eye of the researchers of the many countries in recent years as the CNN has shown promising performances in several computer vision and machine learning tasks. This paper describes the underlying architecture and various applications of Convolutional Neural Network.

The COVID-2019 disease caused by the SARS-CoV-2 virus (aka 2019-nCoV) has raised significant health concerns in China and worldwide. While novel drug discovery and vaccine studies are long, repurposing old drugs against the COVID-2019 epidemic can help identify treatments, with known preclinical, pharmacokinetic, pharmacodynamic, and toxicity profiles, which can rapidly enter Phase 3 or 4 or can be used directly in clinical settings. In this study, we presented a novel network based drug repurposing platform to identify potential drugs for the treatment of COVID-2019. We first analysed the genome sequence of SARS-CoV-2 and identified SARS as the closest disease, based on genome similarity between both causal viruses, followed by MERS and other human coronavirus diseases. Using our AutoSeed pipeline (text mining and database searches), we obtained 34 COVID-2019-related genes. Taking those genes as seeds, we automatically built a molecular network for which our module detection and drug prioritization algorithms identified 24 disease-related human pathways, five modules and finally suggested 78 drugs to repurpose. Following manual filtering based on clinical knowledge, we re-prioritized 30 potential repurposable drugs against COVID-2019 (including pseudoephedrine, andrographolide, chloroquine, abacavir, and thalidomide) . We hope that this data can provide critical insights into SARS-CoV-2 biology and help design rapid clinical trials of treatments against COVID-2019.

With the COVID-19 pandemic continuing and the resulting economic burden increasingly apparent, the Indonesian government began to prepare a "new normal" phase and make peace with COVID-19. From this new decision arises the question of the readiness of businesses and the industrial sector to resume operations amid COVID-19. This article aims to provide concise and precise information about the preparations that can be made by businesses to operate safely amid COVID-19 based on existing scientific studies and literatures. From the literature visits it can be concluded that transmission and danger of a COVID-19 pandemic can be prevented through: creation of infectious disease prevention and response plan, implementing basic infection prevention measures, policies and procedures for proper identification and isolation of sick people, applying flexibilities in policies, and protections in the workplace.

Mobile devices have become tools we spend our free time where we carry them with us every moment, they allow us to interact with the environment, we immortalize the moment when necessary. These devices which we spend most of our daily life become very common in recent years and even there are unique business areas emerged. It was announced that the number of people using smartphones is over than 2.5 billion in the first quarter of 2016. As people become more addicted to mobile technology, they become the target of malevolent people. A huge increase in the number of mobile malware is observed as the number of the users increase. Billions of users at risk day by day due to the development of the methods. We have addressed the recent methods used and the types of malware that target mobile devices in our study. We have mentioned the proxy server and reverse proxy server operation logic. We discuss the method of turning mobile devices into reverse proxy servers, risks involved and protection methods.

Cells respond to a myriad of stressors by senescing, acquiring stable growth arrest, morphologic and metabolic changes, and a senescence-associated-secretory-phenotype (SASP). The heterogeneity of senescent cells (SnCs) and their SASP is vast, yet poorly characterized. SnCs have diverse roles in health and disease and are therapeutically targetable, making characterization of SnCs and harmonization of their nomenclature a priority. The Cellular Senescence Network (SenNet), a NIH Common Fund initiative, will leverage emerging single cell and spatial-omics to identify and map SnCs in numerous organs across the lifespan of humans and mice. A common coordinate framework will integrate the data, using validated, standardized methods, creating public 4-dimensional SnC atlases. Key SenNet deliverables include development of innovative tools/technologies to detect SnCs, biomarker discovery, common annotations to describe SnCs and extensive public data sets. The goal is to comprehensively understand and map SnCs for diagnostic and therapeutic purposes to improve human health.

The coronavirus (covid-19) pandemic is putting healthcare systems across the world under unprecedented and increasing pressure according to the World Health Organization (WHO). With the advances in computer algorithms and especially Artificial Intelligence, the detection of this type of virus in the early stages will help in fast recovery and help in releasing the pressure off healthcare systems. In this paper, a GAN with deep transfer learning for coronavirus detection in chest x-ray images is presented. The lack of benchmark datasets for covid-19 especially in chest x-rays images is the main motivation of this research. The main idea is to collect all the possible images for covid-19 that exists until the writing of this research and use the GAN network to generate more images to help in the detection of the virus from the available x-rays images with the highest accuracy possible. The dataset used in this research was collected from different sources and it is available for researchers to download and use it. The number of images in the collected dataset is 307 images for four different types of classes. The classes are the covid-19, normal, pneumonia bacterial, and pneumonia virus. The dataset is divided into 90% for the GAN and the training and the validation phase, while 10% used in the testing phase. The GAN helps in generating more images from the original dataset to be 30 times larger than the originally collected dataset. The GAN also help in overcoming the overfitting problem and made the proposed model more robust. Three deep transfer models are selected in this research for investigation. The models are the Alexnet, Googlenet, and Restnet18. Those models are selected based on their small number of layers on their architectures, which will reflect in reducing the complexity of the models and the consumed memory and time. Using a combination of GAN and deep transfer models prove it is efficiency according to validation, testing accuracy, and performance measurements such as precision, recall, and F1 score. Three case scenarios are tested through the paper, the first scenario which includes 4 classes from the dataset, while the second scenario includes 3 classes and the third scenario includes 2 classes. All the scenarios include the covid-19 class as it is the main target of this research to be detected. In the first scenario, the Googlenet is selected to be the main deep transfer model as it achieves 80.6% in testing accuracy. In the second scenario, the Alexnet is selected to be the main deep transfer model as it achieves 85.2% in testing accuracy, while in the third scenario which includes 2 classes(covid-19, and normal), Googlenet is selected to be the main deep transfer model as it achieves 100% in testing accuracy and 99.9% in the validation accuracy. All the performance measurement strengthen the obtained results through the research. Finally, this research may be considered one of the first trails to use GAN and deep transfer models together to help in detecting coronaviruses (covid-19) within the absence of a benchmark dataset around the world, especially in x-rays chest images.

It has been a long time since the world has experienced a pandemic with such a rapid devastating impact as the current COVID-19 pandemic. The causative agent, the Severe Acute Respiratory Syndrome coronavirus 2 (SARS-CoV-2) is further unusual in that it appears capable of infecting many different mammal species. As a significant proportion of people worldwide are infected with SARS-CoV-2 and may spread the infection unknowingly before symptoms occur or without any symptoms ever occurring, there is a non-negligible risk of humans spreading SARS-CoV-2 to wildlife, in particular mammals. Because of SARS-CoV-2’s evolutionary origins in bats and reports of humans transmitting the virus to pets and zoo animals, regulations for prevention of human-to-animal transmission have so far focused mostly on these animal groups. Here, we summarize recent studies and reports that show that a wide range of distantly related mammals are likely susceptible to SARS-CoV-2 and that susceptibility or resistance to the virus is in general not predictable, or only to some extent, by phylogenetic proximity to known susceptible or resistant hosts. In the absence of solid evidence on the SARS-CoV-2 susceptibility/resistance for each of the >5,500 mammal species, we argue that sanitary precautions should be taken when interacting with any mammal species in the wild. Preventing human-to-wildlife SARS-CoV-2 transmission is important for protecting these (sometimes endangered) animals from disease, but also to avoid establishment of novel SARS-CoV-2 reservoirs in wild animals. The risk of repeated re-infection of humans from such a wildlife reservoir could severely hamper SARS-CoV-2 control efforts. For wildlife fieldworkers interacting directly or indirectly with mammals, we recommend sanitary precautions such as physical distancing, wearing face masks and gloves, and frequent decontamination, which are very similar to regulations currently imposed to prevent transmission among humans.

This work mainly discusses an innovative teaching platform on Unmanned Aerial Vehicle digital mapping for Remote Sensing (RS) education at Wuhan University, underlining the fast development of RS technology. Firstly, we introduce and discuss the future development of the Virtual Simulation Experiment Teaching Platform for Unmanned Aerial Vehicle (VSETP-UAV). It includes specific topics such as the Systems and function Design, teaching and learning strategies, and experimental methods. This study shows that VSETP-UAV expands the usual content and training methods related to RS education, and creates a good synergy between teaching and research. The results also show that the VSETP-UAV platform is of high teaching quality producing excellent engineers, with high international standards and innovative skills in the RS field. In particular, it develops students' practical skills with technical manipulations of dedicated hardware and software equipment (e.g., UAV) in order to assimilate quickly this particular topic. Therefore, students report that this platform is more accessible from an educational point-of-view than theoretical programs, with a quick way of learning basic concepts of RS. Finally, the proposed VSETP-UAV platform achieves a high social influence, expanding the practical content and training methods of UAV based experiments, and providing a platform for producing high-quality national talents with internationally recognized topics related to emerging engineering education.

COVID-19 is a severe global problem, and AI can play a significant role in preventing losses by monitoring and detecting infected persons in early-stage. This paper aims to propose a high-speed and accurate fully-automated method to detect COVID-19 from the patient's CT scan images. We introduce a new dataset that contains 48260 CT scan images from 282 normal persons and 15589 images from 95 patients with COVID-19 infections. At the first stage, this system runs our proposed image processing algorithm to discard those CT images that inside the lung is not properly visible in them. This action helps to reduce the processing time and false detections. At the next stage, we introduce a novel method for increasing the classification accuracy of convolutional networks. We implemented our method using the ResNet50V2 network and a modified feature pyramid network alongside our designed architecture for classifying the selected CT images into COVID-19 or normal with higher accuracy than other models. After running these two phases, the system determines the condition of the patient using a selected threshold. We are the first to evaluate our system in two different ways. In the single image classification stage, our model achieved 98.49% accuracy on more than 7996 test images. At the patient identification phase, the system correctly identified almost 234 of 245 patients with high speed. We also investigate the classified images with the Grad-CAM algorithm to indicate the area of infections in images and evaluate our model classification correctness.

Deep neural networks (DNNs) have made a huge impact in the field of machine learning by providing unbeatable humanlike performance to solve real-world problems such as image processing and natural language processing (NLP). Convolutional neural network (CNN) and recurrent neural network (RNN) are two typical architectures that are widely used to solve such problems. Time sequence-dependent problems are generally very challenging, and RNN architectures have made an enormous improvement in a wide range of machine learning problems with sequential input involved. In this paper, different types of RNN architectures are compared. Special focus is put on two well-known gated-RNN’s Long Term Short Memory (LSTM) and Gated Recurrent Unit (GRU). We evaluated these models on the task of force estimation system in pouring. In this study, four different models including multi-layers LSTM, multi-layers GRU, single-layer LSTM and single-layer GRU) were created and trained. The result suggests that multi-layer GRU outperformed other three models.

The present grievous situation of the tuberculosis disease can be improved by efficient case management and timely follow-up evaluations. With the advent of digital technology this can be achieved by quick summarization of the patient-centric data. The aim of our study was to assess the effectiveness of the ODK Scan paper-to-digital system during testing period of three months. A sequential, explanatory mixed-method research approach was employed to elucidate technology use. Training, smartphones, application and 3G enabled SIMs were provided to the four field workers. At the beginning, baseline measures of the data management aspects were recorded and compared with endline measures to see the impact of ODK Scan. Additionally, at the end, users’ feedback was collected regarding app usability, user interface design and workflow changes. 122 patients’ records were retrieved from the server and analysed for quality. It was found that ODK Scan recognized 99.2% of multiple choice bubble responses and 79.4% of numerical digit responses correctly. However, the overall quality of the digital data was decreased in comparison to manually entered data. Using ODK Scan, a significant time reduction is observed in data aggregation and data transfer activities, however, data verification and form filling activities took more time. Interviews revealed that field workers saw value in using ODK Scan, however, they were more concerned about the time consuming aspects of the use of ODK Scan. Therefore, it is concluded that minimal disturbance in the existing workflow, continuous feedback and value additions are the important considerations for the implementing organization to ensure technology adoption and workflow improvements.

The development of low-cost, open-source Remotely Operated Vehicle (ROV) systems has provided almost unrestricted access for researchers looking to monitor the marine environment in ever greater resolution. Sampling microbial communities from the marine environment, however, still usually relies on Niskin-bottle sampling (ROV or CTD based), a method which introduces an inaccuracy and variability that is incompatible with metatranscriptomic analysis. Here, we describe a versatile, easily-replicated platform which achieves in situ mRNA preservation, via the addition of RNAlater to filtered microbial cells, to enhance ROV or CTD functionality.

Background: Access to rehabilitation is crucial for the realization of the right to health and a proper concern of global health. Yet, reliable information to guide rehabilitation service planning is unavailable in many countries in part due to the lack of appropriate indicators. To ensure universal health coverage and meet the central imperative of “leaving no one behind” countries must be able to assess key aspects of rehabilitation policy and provision and monitor how they have discharged their human rights responsibilities towards those most disadvantaged, including people with disability. This article describes the process of developing an expert guided indicator framework to assess governments’ efforts and progress in strengthening rehabilitation in line with the Convention on the Rights of Persons with Disabilities. Methods: A systems methodology - concept mapping - was used to capture, aggregate and confirm the knowledge of diverse stakeholders on measures thought to be useful for monitoring the implementation of the Convention with respect to health related rehabilitation. 56 individuals generated a list of 107 indicators through online brainstorming which were subsequently sorted by 37 experts from the original panel into non overlapping categories. 41 participants rated the indicators for importance and feasibility. Multivariate statistical techniques where used to explore patterns and themes in the data and create the indicators’ organizing framework which was verified and interpreted by participants. Results: A concept map of 11 clusters of indicators emerged from the analysis grouped into three broader themes: Governance and Leadership (3 clusters); Service Delivery, Financing and Oversight (6 clusters); and Human Resources (2 clusters). The RESYST was comprehensive and well aligned with the Convention. On average, there was a moderately positive correlation between importance and feasibility of the indicators (r=.58) with experts prioritizing the indicators contained in the clusters of the Governance and Leadership domain. Two of the most important indicators arose from the Service Delivery, Financing and Oversight domain and reflect the need to monitor unmet needs and barriers in access to rehabilitation. In total, 59 indicators achieved above average score for importance and comprised the two–tiered priority set of indicators. Conclusion: Concept mapping was successful in generating a shared model that enables a system’s view of the most critical legal, policy and programmatic factors that must be addressed when assessing country efforts to reform, upscale and improve rehabilitation services. The RESYST provides a data driven basis for the development of standardized data collection tools to facilitate comparative analysis of rehabilitation systems.

During the COVID-19 outbreak, most university courses have been offered on online platforms. A sudden shift from face-to-face classroom learning to online formats could influence the learning effectiveness of classes. This study aims to investigate differences in the learning effectiveness of online and face-to-face lecture courses. It also explores factors that impact the effectiveness of online instruction. These factors include interactions among learners, interactions between learners and the instructor, the quality of online platforms, learners’ ability to use devices and follow instructions, and learners’ situational challenges. The study participants were 261 university students at King Mongkut’s University of Technology Thonburi in Bangkok, Thailand. All participants were enrolled in at least one lecture course, such as history, humans and the environment, the environment and development, or general philosophy, during the 2019 academic year. A questionnaire was distributed to participants after they completed these courses in May 2020. Paired simple t-test analyses were used to compare the effectiveness of online and face-to-face classes, and a multiple regression analysis was used to identify factors that impact the learning effectiveness of online classes. The results show that online classes are less effective than face-to-face courses. The multiple regression analysis also revealed that the effectiveness of online learning was significantly impacted by learners’ ability to interact with classmates during class, their ability to interact with instructors after the class, the quality of online platforms, and disturbances or distractions in learners’ environments.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

The separation of sister chromatids during anaphase is the culmination of mitosis and one of the most strikingly beautiful examples of cellular movement. It consists of two distinct processes: Anaphase A, the movement of chromosomes toward spindle poles via shortening of the connecting fibers, and anaphase B, separation of the two poles from one another via spindle elongation. I focus here on anaphase A chromosome-to-pole movement. The chapter begins by summarizing classical observations of chromosome movements, which support the current understanding of anaphase mechanisms. Live cell fluorescence microscopy studies showed that poleward chromosome movement is associated with disassembly, or ‘melting’ of the kinetochore-attached microtubule fibers that link chromosomes to poles. Microtubule-marking techniques established that kinetochore-fiber disassembly often occurs through a ‘pac-man’ mechanism, where tubulin subunits are lost from kinetochore-attached plus ends and the kinetochore appears to consume its microtubule track as it moves poleward. In addition, kinetochore-fiber disassembly in many cells occurs partly through ‘flux’, where the microtubules flow continuously toward the poles and tubulin subunits are lost from minus ends. Molecular mechanistic models for how load-bearing attachments are maintained to disassembling microtubule ends, and how the forces are generated to drive pac-man and flux-based movements, are discussed.

Cronbach’s (1957) famous division of scientific psychology into two disciplines is still actual for the fields of cognition (general mechanisms) and intelligence (dimensionality of individual differences). The welcome integration of the two fields requires the construction of mechanistic models of cognition and cognitive development that explain key phenomena in individual differences research. In this paper we argue that network modeling is a promising approach to integrate the processes of cognitive development and (developing) intelligence into one unified theory. Network models are defined mathematically, describe mechanisms on the level of the individual, and are able to explain positive correlations among intelligence subtest scores - the empirical basis for the well-known g-factor - as well as more complex factorial structures. Links between network modeling, factor modeling and item response theory allow for a common metric, encompassing both discrete and continuous characteristics, for cognitive development and intelligence.

Physical distancing and wearing a face mask are key interventions to prevent COVID-19. While this remains difficult to practice for millions of firefighters in fire engines responding to emergencies, the delayed forthcoming of evidence on the physical effectiveness of such safety interventions in this setting presents a major problem. In this field experimental study, we provided initial evidence to close this gap. We examined total aerosol burden in the cabin of a fire engine whilst manipulating crew size, natural ventilation, use of FFP2 respirators and use of SCBA full-face masks during 15-minute driving periods. At the same time, we controlled for crew activity and speaking, vehicle speed, cabin air temperature, pressure and humidity. Limiting the crew size, using FFP2 respirators and not donning SCBA full-face masks was associated with a reduction of the arithmetic mean of total aerosol burden of up to 49%. Natural ventilation as tested in this study was associated with both an increase and a decrease of total aerosol burden. This study provided initial evidence on the physical effectiveness of safety interventions in fire engines to reduce potential airborne transmission of SARS-CoV-2 through aerosols. More research about the physical and clinical effectiveness of such safety interventions is needed.

Music has the innate potential to reach all parts of the brain, stimulates certain brain areas which are not achievable through other modalities. Music Therapy (MT) is being used for more than a century to treat individuals who needs personalized care. MT optimizes motor, speech and language responsibilities of the brain and improves cognitive performance. Pervasive developmentdisorder (PDD) is a multifaceted, neuro developmental disorder and autism spectrum disorder (ASD) comes under PDD, which is defined by deficiencies in three principal spheres: social connection with others, communicative and normal movement skills. The conventional imaging studies illustrate reduced brain area connectivity in people with ASD, involving selected parts of the brain cortex. People with ASD express much interest in musical activities which engages the brain network areas and improves communication and social skills.The main objective of this review is to analyze the potential role of MT in treating the neurological conditions, particularly ASD. Evidence based studies have reported the extensive therapeutic application of music on various part of the brain in a nonverbal child with autism through hearing or making music.Hence we hypothesized that MT intervention can improve the communication capacity in people with ASD, than customary neurorestoration therapy alone.

Suicidal behaviour remains difficult to predict and prevent, even for experienced mental health care professionals. The known distal risk factors for suicidal behaviour are not sufficiently specific to fully understand the complex dynamic processes that precede a suicide attempt. Real-time mobile monitoring data can be used to analyse proximal risk mechanisms within the suicidal process. At the same time smartphone-based safety planning and self-monitoring may enhance a patient’s self-management skills thereby increasing their capacity to respond to a suicidal crisis and to become more aware of crisis symptoms. The current paper describes the theoretical and conceptual rationale for the CASPAR study which applies an innovative approach to the study of suicidal processes. It uses basic science approaches to inform the implementation of an innovative suicide prevention intervention. We aim to develop and implement mobile safety plan in conjunction with real-time monitoring in order to both directly implement suicide prevention interventions and to study the ongoing dynamics of individual suicidal behaviour by applying network analysis.

Security has become a critical issue in today’s highly distributed and networked systems. Network intrusion detection systems (NIDSs), especially signature-based NIDSs, are being widely deployed in a distributed network environment with the purpose of defending against a variety of network attacks. Most of the commercially available NIDSs are software based and rely on pattern matching to extract the threat from network traffic. The increase in network speed and traffic may make existing algorithms to become a performance bottleneck. Therefore it is very necessary to develop faster and more efficient pattern matching algorithm in order to overcome the troubles on performance of NIDSs. Therefore, we propose a multi fusion pattern matching algorithm for Network Intrusion Detection Systems. The results obtained in percentages from the proposed fusion algorithm given better values in terms processing time in milliseconds than the existing algorithms when data English text are applied to evaluate the fusion performances.

Sustainable food consumption has attracted a widespread attention during last decades by scholars, policy makers and consumers. In line with this, farmers’ markets (FMs) have the potential to encourage sustainable agricultural production and consumption. By reducing the number of actors and distances along the food chain, these alternative food systems foster the reconnection between farmers and consumers and contribute to different social, economic and environmental sustainable goals. This paper provides insights on the role of consumers' sustainability concerns related to their motivation for shopping at FMs. By means of a choice experiment, we analyze the determinants of consumers’ WTP for buying apples at FMs. We are particularly interested in understanding how attitudes towards the three sustainability dimensions are related to consumer preferences in this context. We find that consumer attitudes towards direct contact with producers, contributing to farmers’ income, and environmental benefits can be directly related to product characteristics that are specific to FMs.

GaN ultraviolet photodetector with metal-semiconductor-metal structure is achieved by growing on a periodic trapezoid column-shape patterned sapphire substrate using metalorganic chemical vapor deposition. Under 5-V reverse bias, the photodetector fabricated on such patterned sapphire substrate exhibits a lower dark current, a higher photocurrent, and a 476 % enhancement in the maximum responsivity as compare with those of the photodetector fabricated on conventional flat sapphire substrate. It is also found that the much larger UV-to-visible rejection ratio and the fact that responsivity drops in a smaller cut-off region are observed from photodetector fabricated by using a periodic trapezoid column-shape patterned sapphire substrate. These phenomena may all be attributed to the reduction of threading dislocation density and the improved quality of GaN film, as well as the internal reflection and/or scattering effect on the interface between GaN film and the periodic trapezoid column-shape pattern of the substrate.

Wetlands benefits can be summarized but are not limited to their ability to store floodwaters and improve water quality, providing habitats for wildlife and supporting biodiversity, as well as aesthetic values. Over the past few decades, remote sensing and geographical information technologies has proven to be a useful and frequent applications in monitoring and mapping wetlands. Combining both optical and microwave satellite data can give significant information about the biophysical characteristics of wetlands and wetlands` vegetation. Also, fusing data from different sensors, such as radar and optical remote sensing data, can increase the wetland classification accuracy. In this paper we investigate the ability of fusion two fine spatial resolution satellite data, Sentinel-2 and the Synthetic Aperture Radar Satellite, Sentinel-1, for mapping wetlands. As a study area in this paper, Balikdami wetland located in the Anatolian part of Turkey has been selected. Both Sentinel-1 and Sentinel-2 images require pre-processing before their use. After the pre-processing, several vegetation indices calculated from the Sentinel-2 bands were included in the data set. Furthermore, an object-based classification was performed. For the accuracy assessment of the obtained results, number of random points were added over the study area. In addition, the results were compared with data from Unmanned Aerial Vehicle collected on the same data of the overpass of the Sentinel-2, and three days before the overpass of Sentinel-1 satellite. The accuracy assessment showed that the results significant and satisfying in the wetland classification using both multispectral and microwave data. The statistical results of the fusion of the optical and radar data showed high wetland mapping accuracy, with an overall classification accuracy of approximately 90% in the object-based classification. Compared with the high resolution UAV data, the classification results give promising results for mapping and monitoring not just wetlands, but also the sub-classes of the study area. For future research, multi-temporal image use and terrain data collection are recommended.

The use of Light Amplification by Stimulated Emission of Radiation (i.e., LASERs or lasers) by the U.S. Department of Defense is not new and includes laser weapons guidance, laser-aided measurements, even lasers as weapons (e.g., Airborne Laser). Lasers in support of telecommunications is also not new. The use of laser light in fiber optics shattered thoughts on communications bandwidth and throughput. Even the use of lasers in space is no longer new. Lasers are being used for satellite-to-satellite crosslinking. Laser communication can transmit orders-of-magnitude more data using orders-of-magnitude less power and can do so with minimal risk of exposure to the sending and receiving terminals. What is new is using lasers as the uplink and downlink between the terrestrial segment and the space segment of satellite systems. More so, the use of lasers to transmit and receive data between moving terrestrial segments (e.g., ships at sea, airplanes in flight) and geosynchronous satellites is burgeoning. This manuscript examines the technological maturation of employing lasers as the signal carrier for satellite communications linking terrestrial and space systems. The purpose of the manuscript is to develop key performance parameters (KPPs) to inform U.S. Department of Defense initial capabilities documents (ICDs) for near-future satellite acquisition and development. By appreciating the history and technological challenges of employing lasers rather than traditional radio frequency sources for satellite uplink and downlink signal carrier, this manuscript recommends ways for the U.S. Department of Defense to employ lasers to transmit and receive high bandwidth, large-throughput data from moving platforms that need to retain low probabilities of detection, intercept, and exploitation (e.g., carrier battle group transiting to a hostile area of operations, unmanned aerial vehicle collecting over adversary areas). The manuscript also intends to identify commercial sector early-adopter fields and those fields likely to adapt to laser employment for transmission and receipt.

The population’s mobility in urban areas is a necessary variable in the modeling of risk scenarios caused by atmospheric contamination. The inclusion of this concept makes static models more dynamic while considering people within a city to be an entity with complex mobility processes. We propose a conceptual and methodological tool to make the representation of the social, economic and territorial components, as well as the patterns in the population´s mobility to delimitate risk areas for human health by exposure of contaminants. In the volatile organic compounds (VOC), benzene, ethylbenzene, toluene and xylene (BTEX) are amongst the most dominant substances in fugitive vapor emissions in gas stations (GS). In urban areas, the exposure to BTEX by residential proximity and proximity to other facilities, which cause intra-urban agglomeration, can impact and affect human health. This model seeks to facilitate the focalization, identification and prioritization of risk areas by BTEX environmental contamination. This article goes beyond de conceptual framework. It suggests methodological and instrumental aspects to be applied in other cities. The government agencies must consider these results when establishing rules, permissions and procedures to reduce environmental pollution for managing the risk in a complex urban environment.

In 1990 the Malaysian Government launched Vision 2020 with the goal of Malaysia becoming a ‘fully developed country’ by the year 2020. In this drive for development the country has been examining many of its key natural assets, exploring how to both preserve them whilst ensuring that they make the maximum possible contribution to national development goals. Endau Rompin is one of these assets, being the second largest National Park in Peninsula Malaysia. The rich tropical rainforest flora and fauna of the Park and its hinterland, however, are threatened by various anthropogenic forces, most notably deforestation and poaching; both of which have taken the Park’s flagship species - the Tiger Panthera tigris jacksoni – towards the brink of local extinction. Malaysia’s statutory East Coast Economic Region Development Council commissioned a study to consider ways of increasing tourism revenues from the Park while at the same time reversing these threats. The key conclusion drawn is that a more holistic, landscape-scale approach should be adopted, with Endau Rompin forming part of a wider strategic economic zone based around sustainable tourism and land management. The proposed expanded zone extends eastwards beyond the confines of the Park, across the coastal plain to the South China Sea, and onwards to the neighbouring Mersing Islands. This expanded zone is referred to as Malaysia’s new ‘Rainforest to Reef Region’.

Lily tepals have a short lifespan. Once the tepals senesce, the ornamental value of the flower is lost. Some cultivars have attractive purple ovaries and fruits which greatly enhance the ornamental value of Asiatic hybrid lilies. However, little is known about the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries. To investigate the transcriptional network that governs purple ovary coloration in Asiatic hybrid lilies, we obtained transcriptome data from green ovaries (S1) and purple ovaries (S2) of Asiatic ‘Tiny Padhye’. Comparative transcriptome analysis revealed 4228 differentially expressed genes. Differential expression analysis revealed that nine unigenes including four CHS genes, one CHI gene, one F3H gene, one F3′H gene, one DFR gene, and one UFGT gene were significantly up-regulated in purple ovaries. One MYB gene, LhMYB12-Lat, was identified as a key transcription factor determining the distribution of anthocyanins in Asiatic hybrid lily ovaries. Further qPCR results showed unigenes related to anthocyanin biosynthesis were highly expressed in purple ovaries of Asiatic ‘Tiny Padhye’ at stages 2 and 3, while they showed an extremely low level of expression in ovaries of Asiatic ‘Yellow Pixels’ during all developmental stages. In addition, shading treatment significantly decreased pigment accumulation by suppressing the expression of several unigenes related to anthocyanin biosynthesis in ovaries of Asiatic ‘Tiny Padhye’. These results could further our understanding of the molecular mechanisms of anthocyanin biosynthesis in Asiatic hybrid lily ovaries.

In recent times, with the increase of Artificial Neural Network (ANN), deep learning has brought a dramatic twist in the field of machine learning by making it more Artificial Intelligence (AI). Deep learning is used remarkably used in vast ranges of fields because of its diverse range of applications such as surveillance, health, medicine, sports, robotics, drones etc. In deep learning, Convolutional Neural Network (CNN) is at the center of spectacular advances that mixes Artificial Neural Network (ANN) and up to date deep learning strategies. It has been used broadly in pattern recognition, sentence classification, speech recognition, face recognition, text categorization, document analysis, scene, and handwritten digit recognition. The goal of this paper is to observe the variation of accuracies of CNN to classify handwritten digits using various numbers of hidden layer and epochs and to make the comparison between the accuracies. For this performance evaluation of CNN, we performed our experiment using Modified National Institute of Standards and Technology (MNIST) dataset. Further, the network is trained using stochastic gradient descent and the backpropagation algorithm.

In cricket, particularly the twenty20 format is most watched and loved by the people, where no one can guess who will win the match until the last ball of the last over. In India, The Indian Premier League (IPL) started in 2008 and now it is the most popular T20 league in the world. So we decided to develop a machine learning model for predicting the outcome of its matches. Winning in a Cricket Match depends on many key factors like a home ground advantage, past performances on that ground, records at the same venue, the overall experience of the players, record with a particular opposition, and the overall current form of the team and also the individual player. This paper briefs about the key factors that affect the result of the cricket match and the regression model that best fits this data and gives the best predictions. Cricket, the mainstream and widely played sport across India which has the most noteworthy fan base. Indian Premier League follows 20-20 format which is very unpredictable. IPL match predictor is a ML based prediction approach where the data sets and previous stats are trained in all dimensions covering all important factors such as: Toss, Home Ground, Captains, Favorite Players, Opposition Battle, Previous Stats etc, with each factor having different strength with the help of KNIME Tool and with the added intelligence of Naive Bayes network and Eulers strength calculation formula.

Multiple sensor nodes known as detection stations make the sensor networks; each node is light and portable. Every sensor node contains power source, microcomputer, transducer and transceiver. Power source provides power to each node. Micro-computer is used for storing and processing the output coming from the sensors. The transducer is used to generate the signals and the transceiver is used to receive and transmit data to the central computer. Eavesdropping gets facilitated with wireless communication, and it has many useful applications in military, homeland, hostile and uncontrolled environments. So it is prone to the high level of security. The process in which information is gathered to form a summarized type for analysis is known as data aggregation, as it is used to reduce the energy consumption in wireless sensor networks. The security issues have become crucial in data aggregation, especially when gets deployed in hostile and remote environment. In wireless sensor networks many secure aggregations have been proposed. It still faces some resource constrained that’s why new techniques are needed. In our survey we will discuss those approaches and their pros and cons.

The concept of a Social License to Operate (SLO) has become increasingly important in the sustainability literature in recent years. Having its origins in the business discourse of the mining industry with respect to limiting opposition to mining projects, the notion of a social contract above and beyond legal requirements has since become applied across a number of different industries. Despite the concepts adoption confusion exists over the practices and outcomes of SLO, and particularly the nature of engagement. Given this situation it is surprising that not more attention to the role of marketing, and social marketing in particular, in operationalizing the concept. The paper discusses the potential of social marketing to contribute to SLO. Economic, political and social relations are complex in SLO and exchange is intricate in such relational environments. A community-based social marketing orientation is proposed as a means to improve exchange relations and enhance engagement. Seven models of SLO related social marketing models are discussed with community-based social marketing and adaptive co-marketing models being regarded as the most positive for the achievement of an SLO. Potential barriers to adoption of these approaches are noted.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

Although suicide is a major public health issue worldwide, we understand little of the onset and development of suicidal behavior. Suicidal behavior is argued to be the end result of the complex interaction between psychological, social and biological factors. Epidemiological studies resulted in a range of risk factors for suicidal behavior, but we do not yet understand how their interaction increases the risk for suicidal behavior. A new approach called network analysis can help us better understand this process as it allows to visualize and quantify complex association between many different symptoms or risk factors. A network analysis of data contain information on suicidal patients can help us understand how risk factors interact and how their interaction is related to suicidal thoughts and behaviour. A network perspective has been successfully applied to the field of depression and psychosis, but not yet to the field of suicidology. In this theoretical article, I will introduce the concept of network analysis to the field of suicide prevention, and offer directions for future applications and studies.

Structure from Motion with Multi-View Stereo photogrammetry (SfM) is increasingly utilised in geoscience investigations as a cost-effective method of acquiring high resolution (sub-meter) topographic data, but has not been thoroughly tested in gullied savanna systems. The aim of this study was to test the accuracy of topographic models derived from aerial (via an Unmanned Aerial Vehicle, ‘UAV’) and ground-based (via a handheld digital camera, ‘Ground’) SfM in modelling a hillslope gully system in dry-tropical savanna, and to assess the strengths and limitations of the approach at different scales. A UAV survey covered an entire hillslope gully system (0.715 km²), whereas a Ground survey covered a single gully within the broader system (650 m²). SfM topographic models, including Digital Surface Models (DSM) and dense point clouds, were compared against RTK-GPS point data and a pre-existing airborne LiDAR Digital Elevation Model (DEM). Results indicate UAV SfM can deliver topographic models with a resolution and accuracy suitable to define gully systems at a hillslope scale (e.g., 0.1 m resolution with ~ 0.5 – 1.3 m elevation error), while ground-based SfM is more capable of quantifying gully morphology (e.g., 0.01 m resolution with ~ 0.1 m elevation error). Key strengths of SfM for these applications include: the production of high resolution 3D topographic models and ortho-photo mosaics, low survey instrument costs (< $AUD 3,000); and rapid survey time (4 and 2 hours for UAV and Ground survey respectively). Current limitations of SfM include: difficulties in reconstructing vegetated surfaces; uncertainty as to optimal survey and processing designs; and high computational demands. Overall, this study has demonstrated great potential for SfM to be used as a cost-effective tool to aid in the mapping, modelling and management of hillslope gully systems at different scales, in tropical savanna landscapes and elsewhere.

Recent advancement of deep learning has been elevated the multifaceted nature in various applications of this field. Artificial neural networks are now turning into a genuinely old procedure in the vast area of computer science; the principal thoughts and models are more than fifty years of age. However, in this modern computing era, 3rd generation intelligent models are introduced by scientists. In the biological neuron, actual film channels control the progression of particles over the layer by opening and shutting in light of voltage changes because of inborn current flows and remotely led to signals. A comprehensive 3rd generation, Spiking Neural Network (SNN) is diminishing the distance between deep learning, machine learning, and neuroscience in a biologically-inspired manner. It also connects neuroscience and machine learning to establish high-level efficient computing. Spiking Neural Networks initiate utilizing spikes, which are discrete functions that happen at focuses as expected, as opposed to constant values. This paper is a review of the biological-inspired spiking neural network and its applications in different areas. The author aims to present a brief introduction to SNN, which incorporates the mathematical structure, applications, and implementation of SNN. This paper also represents an overview of machine learning, deep learning, and reinforcement learning. This review paper can help advanced artificial intelligence researchers to get a compact brief intuition of spiking neural networks.

We study latching dynamics in the adaptive Potts model network, through numerical simulations with randomly and also weakly correlated patterns, and we focus on comparing its slowly and fast adapting regimes. A measure, Q, is used to quantify the quality of latching in the phase space spanned by the number of Potts states S, the number of connections per Potts unit C and the number of stored memory patterns p. We find narrow regions, or bands in phase space, where distinct pattern retrieval and duration of latching combine to yield the highest values of Q. The bands are confined by the storage capacity curve, for large p, and by the onset of finite latching, for low p. Inside the band, in the slowly adapting regime, we observe complex structured dynamics, with transitions at high crossover between correlated memory patterns; while away from the band latching transitions lose complexity in different ways: below, they are clear-cut but last so few steps as to span a transition matrix between states with few asymmetrical entries and limited entropy; while above, they tend to become random, with large entropy and bi-directional transition frequencies, but indistinguishable from noise. Extrapolating from the simulations, the band appears to scale almost quadratically in the p - S plane, and sublinearly in p - C. In the fast adapting regime the band scales similarly, and it can be made even wider and more robust, but transitions between anti-correlated patterns dominate latching dynamics. This suggest that slow and fast adaptation have to be integrated in a scenario for viable latching in a cortical system. The results for the slowly adapting regime, obtained with randomly correlated patterns, remain valid also for the case with correlated patterns, with just a simple shift in phase space.

COVID-19 has affected 212 countries around the world, killing nearly 300,000 and infecting more than 4.4 million by May 14, 2020. Bangladesh, a South Asian low-middle-income economy, has experienced a demographic and epidemiological transition with rapid urbanization and a gradual increase in life expectancy. It is the seventh most populous country in the world and population of the country is expected to be nearly double by 2050. The increasing burden of communicable diseases in Bangladesh can be attributable to rapid urbanization and nearly 50% of all slum dwellers of the country live in Dhaka division. In 2017, National Rapid Response Team of IEDCR investigated 26 incidents of disease outbreak. The joint survey of the Power and Participation Research Centre and BRAC Institute of Governance and Development reveals that per capita daily income of urban slum and rural poor drops by 80% due to present countrywide shutdown enforced by the government to halt the spread of Covid-19. 40%-50% of these population took loans to meet the daily expenses. However, the country has just 127,000 hospital beds, 91,000 of them in government-run hospitals. Researchers say, the country’s economy is economy is losing BDT 33 billion every day from its service and agriculture sectors during the nationwide shutdown.

Myocarditis is the form of an inflammation of the middle layer of the heart wall which is caused by a viral infection and can affect the heart muscle and its electrical system. It has remained as one of the most challenging diagnoses in cardiology. Myocardial is the prime cause of unexpected death in approximately 20% of adults less than 40 years of age. Cardiac MRI (CMR) has been considered as a noninvasive and golden standard diagnostic tool for suspected myocarditis and plays an indispensable role in diagnosing various cardiac diseases. However, the performance of CMR is heavily dependent on the clinical presentation and non-specific features such as chest pain, arrhythmia, and heart failure. Besides, other imaging factors like artifacts, technical errors, pulse sequence, acquisition parameters, contrast agent dose, and more importantly qualitatively visual interpretation can affect the result of the diagnosis. This paper introduces a new deep learning-based model called Convolutional Neural Network-Clustering (CNN-KCL) to diagnose the Myocarditis. The hybrid CNN-KCL method performs the early and accurate diagnosis of Myocarditis. To the best-of-our-knowledge, a Convolutional neural network has never been used before for the diagnosis of Myocarditis. In this study, we used 47 subjects to diagnose myocarditis patients from Tehran's Omid Hospital. The total number of data examined is 10425. Our results demonstrate that CNN-KCL achieves 92.3% in terms of diagnosis myocarditis prediction accuracy which is significantly better than those reported in previous studies.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

One of the most common and important destructive attacks on the victim system is Advanced Persistent Threats (APT)-attack. The APT attacker can achieve his hostile goals by obtaining information and gaining financial benefits regarding the infrastructure of a network. One of the solutions to detect a secret APT attack is using network traffic. Due to the nature of the APT attack in terms of being on the network for a long time and the fact that the network may crash because of high traffic, it is difficult to detect this type of attack. Hence, in this study, machine learning methods such as C5.0 decision tree, Bayesian network and deep neural network are used for timely detection and classification of APT-attacks on the NSL-KDD data set. Moreover, 10-fold cross validation method is used to experiment these models. As a result, the accuracy (ACC) of the C5.0 decision tree, Bayesian network and 6-layer deep learning models is obtained as 95.64%, 88.37% and 98.85%, respectively, and also, in terms of the important criterion of the false positive rate (FPR), the FPR value for the C5.0 decision tree, Bayesian network and 6-layer deep learning models is obtained as 2.56, 10.47 and 1.13, respectively. Other criterions such as sensitivity, specificity, accuracy, false negative rate and F-measure are also investigated for the models, and the experimental results show that the deep learning model with automatic multi-layered extraction of features has the best performance for timely detection of an APT-attack comparing to other classification models.

Sentinel-2 can provide multi-spectral optical remote sensing images in RGBN bands with a spatial resolution of 10m, but the spatial details provided are not enough for many applications. WorldView can provide HR multi-spectral images less than 2m, but it is a commercial paid resource with relatively high usage costs. In this paper, without any available reference images, Sentinel-2 images at 10m resolution are improved to a resolution of 2.5m through super-resolution (SR) based on deep learning technology. Our model, named DKN-SR-GAN, uses degradation kernel estimation and noise injection to construct a dataset of near-natural low-high-resolution (LHR) image pairs, with only low-resolution (LR) images and no high-resolution (HR) prior information. DKN-SR-GAN uses the Generative Adversarial Networks (GAN) combined of ESRGAN-type generator, PatchGAN-type discriminator and the VGG-19-type feature extractor, using perceptual loss to optimize the network, so as to obtain SR images with clearer details and better perceptual effects. Experiments demonstrate that in the quantitative comparison of the non-reference image quality assessment (NR-IQA) metrics like NIQE, BRISQUE and PIQE, as well as the intuitive visual effects of the generated images, compared with state-of-the-art models such as EDSR8-RGB, RCAN and RS-ESRGAN, our proposed model has obvious advantages.

Precision agriculture is a farm management technology that involves sensing and then responding to the observed variability in the field. Remote sensing is one of the tools of precision agriculture. The emergence of small unmanned aerial vehicles (sUAV) have paved the way to accessible remote sensing tools for farmers. This paper describes the comparison of two popular off-the-shelf sUAVs: 3DR Iris and DJI Phantom 2. Both units are equipped with a camera gimbal attached with a GoPro camera. The comparison of the two sUAV involves a hovering test and a rectilinear motion test. In the hovering test, the sUAV was allowed to hover over a known object and images were taken every second for two minutes. The position of the object in the images was measured and this was used to assess the stability of the sUAV while hovering. In the rectilinear test, the sUAV was allowed to follow a straight path and images of a lined track were acquired. The lines on the images were then measured on how accurate the sUAV followed the path. Results showed that both sUAV performed well in both the hovering test and the rectilinear motion test. This demonstrates that both sUAVs can be used for agricultural monitoring.

Recently, design of electric scooters (ESs) has commonly adopted brushless DC motors (BLDCMs) in place of brushed DC motors. This invention develops a new anti-lock braking system (ABS), based on a slip-ratio estimator, for ES utilizing the braking force generated by the BLDCM when electrical energy releases to the load yielding an analogous effect of ABS control in gas-engine vehicles. Comparing to mechanical ABS, the design possesses the advantages of rapid torque responses due to fast actuating response. The electrical ABS is realized by associating with kinematic and Short-circuit braking. A current controller is used to adjust the braking force, while the sliding mode control strategy is adopted to regulate the slip ratio for best road adhesion while braking. Real-world experiments have been conducted for functional and performance verification.

Electric vehicles (EV) are getting more commonplace in the transportation sector in recent times. As the present trend suggests, this mode of transport is likely to replace the internal combustion engine (ICE) vehicles in near future. Each of the main EV components has a number of technologies that are currently in use or can become prominent in the future. EVs can cause significant impacts on the environment, power system, and other related sectors. The present power system can face huge instabilities with enough EV penetration; but with proper management and coordination, EVs can be turned into a major contributor to the successful implementation of smart grid. There are possibilities of immense environmental benefits as well, as the EVs can extensively reduce the greenhouse gas emission from the transportation sector. However, there are some major obstacles for EVs to overcome before replacing the ICE vehicles totally. This paper is focused on reviewing all the useful data available on EV configurations, energy sources, motors, charging techniques, optimization techniques, impacts, trends, and possible directions of future developments. Its objective is to provide an overall picture of the current EV technology and ways of future development to assist in future researches in this sector.

This study sought to investigate steel frames’ performance with dual lateral loader system (Frame bending + bracings of divergent and convergent) in near and far filed to fault. In order to this, four categories of steel frame with dual system with 8, 10 and 12 story are designed with average formation based on existing seismic regulation in 2800 standard of Iran and tenth chapter of national regulations of construction (planning and performing steel construction). Time history non-linear dynamic analysis under the effect of near and far field earthquakes has been done on plan’s models. Then the maximum of floors’ dislocation, floors’ drift, roof dislocation, base shear and energy curves of frames are shown and compared with each other. All non-linear time history analyses have been accomplished using PERFORM 3D software.

The problem of quantifying the vulnerability of graphs has received much attention nowadays, especially in the field of computer or communication networks. In a communication network, the vulnerability measures the resistance of the network to disruption of operation after the failure of certain stations or communication links. If we think of a graph as modeling a network, the average lower 2-domination number of a graph is a measure of the graph vulnerability and it is defined by ${\gamma }_{2av}\left(G\right)=\frac{1}{\left|V\left(G\right)\right|}{\sum }_{v\in V\left(G\right)}{\gamma }_{2v}\left(G\right)$, where the lower 2-domination number, denoted by ${\gamma }_{2v}\left(G\right)$, of the graph G relative to v is the minimum cardinality of 2-domination set in G that contains the vertex v. In this paper, the average lower 2-domination number of wheels and some related networks namely gear graph, friendship graph, helm graph and sun flower graph are calculated. Then, we offer an algorithm for computing the 2-domination number and the average lower 2-domination number of any graph G.

Graph coloring is a manifestation of graph partitioning, wherein, a graph is partitioned based on the adjacency of its elements. Partitioning serves potentially as a compartmentalization for any structural problem. Vertex coloring is the heart of the problem which is to find the chromatic number of a graph. The fact that there is no general efficient solution to this problem that may work unequivocally for all graphs opens up the realistic scope for combinatorial optimization algorithms to be invoked. The algorithmic complexity of graph coloring is non-deterministic in polynomial time (NP) and hard. To the best of our knowledge, there is no algorithm as yet that procures an exact solution of the chromatic number comprehensively for any and all graphs within the polynomial (P) time domain. However, several heuristics as well as some approximation algorithms have been attempted to obtain an approximate solution for the same. Here, we present a novel heuristic, namely, the 'trailing path', which returns an approximate solution of the chromatic number within polynomial time, and, with a better accuracy than most existing algorithms. The ‘trailing path’ algorithm is effectively a subtle combination of the search patterns of two existing heuristics (DSATUR and Largest First), and, operates along a trailing path of consecutively connected nodes (and thereby effectively maps to the problem of finding spanning tree(s) of the graph) during the entire course of coloring, where essentially lies both the novelty and the apt of the current approach. The study also suggests that the judicious implementation of randomness is one of the keys towards rendering an improved accuracy in such combinatorial optimization algorithms. Apart from the algorithmic attributes, essential properties of graph partitioning in random and different structured networks have also been surveyed, followed by a comparative study. The study reveals the remarkable stability and absorptive property of chromatic number across a wide array of graphs. Finally, a case study is presented to demonstrate the potential use of graph coloring in protein design – yet another hard problem in structural and evolutionary biology.

HER2/neu positive breast tumors predict a high mortality and comprise 25-30% of breast cancer. We have shown that Flavokawain A (FKA) preferentially reduces the viabilities of HER2 overexpressing breast cancer cell lines (i.e. SKBR3 and MCF7/HER2) versus those with less HER2 expression (i.e. MCF7 and MDA-MB-468). FKA at cytotoxic concentrations to breast cancer cell lines also has minimal effect on the growth of non-malignant breast epithelial MCF10 cells. FKA induces G2M arrest in cell cycle progression of HER2 overexpressing breast cancer cell lines through inhibition of Cdc2 and Cdc25C phosphorylation and down-regulation of Myt1 and Wee1expression leading to increased Cdc2 kinase activities. In addition, FKA induces apoptosis in SKBR3 cells by increasing the protein expression of Bim and BAX and decreasing expression of Bcl₂, Bcl_x/L , XIAP and survivin. FKA also down-regulates the protein expression of HER-2 and inhibits AKT phosphorylation. Herceptin plus FKA treatment leads to enhanced growth inhibitory effect on HER-2 overexpressing breast cancer cell lines through down-regulation of Myt1, Wee1, Skp2, Survivin and XIAP. Our results suggest the promise of FKA as a novel apoptosis inducer and G2 checkpoint abrogating agent in combination with Herceptin for treatment of HER2 overexpressing breast cancer.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

This paper presents a review of cloud application architectures and its evolution. It reports observations being made during the course of a research project that tackled the problem to transfer cloud applications between different cloud infrastructures. As a side effect we learned a lot about commonalities and differences from plenty of different cloud applications which might be of value for cloud software engineers and architects. Throughout the course of the research project we analyzed industrial cloud standards, performed systematic mapping studies of cloud-native application related research papers, performed action research activities in cloud engineering projects, modeled a cloud application reference model, and performed software and domain specific language engineering activities. Two major (and sometimes overlooked) trends can be identified. First, cloud computing and its related application architecture evolution can be seen as a steady process to optimize resource utilization in cloud computing. Second, this resource utilization improvements resulted over time in an architectural evolution how cloud applications are being build and deployed. A shift from monolithic servce-oriented architectures (SOA), via independently deployable microservices towards so called serverless architectures is observable. Especially serverless architectures are more decentralized and distributed, and make more intentional use of independently provided services. In other words, a decentralizing trend in cloud application architectures is observable that emphasizes decentralized architectures known from former peer-to-peer based approaches. That is astonishing because with the rise of cloud computing (and its centralized service provisioning concept) the research interest in peer-to-peer based approaches (and its decentralizing philosophy) decreased. But this seems to change. Cloud computing could head into future of more decentralized and more meshed services.

The stromal vascular cell fraction (SVF) of visceral and subcutaneous adipose tissue (VAT and SAT) has increasingly come into focus in stem cell research, since these compartments represent a rich source of multipotent adipose-derived stem cells (ASCs). ASCs exhibit a self- renewal potential and differentiation capacity. Our aim was to study the different expression of embryonic stem cell markers NANOG, SOX2 and OCT3/4 and to evaluate if there exists a hierarchal role in this network in ASCs derived from both SAT and VAT. ASCs were isolated from SAT and VAT biopsies of 72 consenting patients (23 men, 47 women; age 45 ± 10; BMI between 25 and 30 range) undergoing elective open-abdominal surgery. Sphere-forming capability was evaluated by plating cells in low adhesion plastic. Stem cell markers CD90 and CD105 were analyzed by flow cytometry and stem cell transcription factors NANOG, SOX2 and OCT3/4 were detected by immunoblotting and Real-Time PCR. NANOG, SOX2 and OCT3/4 interplay was explored by gene silencing. ASCs from VAT and SAT confirmed their mesenchymal stem cell (MSC) phenotype expressing the specific MSC markers CD90, CD105, NANOG, SOX2 and OCT3/4. NANOG silencing induced a significant OCT 3/4 (70% ± 0.05) and SOX2 (75% ± 0.03) down-regulation whereas SOX2 silencing did not affect NANOG gene expression. Adipose tissue is an important source of MSC, and siRNA experiments endorse a hierarchical role of NANOG in the complex transcription network that regulates pluripotency and plasticity.

Small and micro hydropower represents an attractive solution for electricity generation, with low cost and low environmental impact. The pump-as-turbine (PAT) approach has promise in this application owing to its low purchase and maintenance costs. In this paper, a new method to predict the inverse characteristic of industrial centrifugal pumps is presented. This method is based on results of simulations performed with commercial three-dimensional CFD software. Model results have been first validated in pumping mode using data supplied by pump manufacturers. Then, results have been compared to experimental data for a pump running in reverse condition. Experimentation has been performed on a dedicated test bench installed in the Department of Civil Construction and Environmental Engineering of the University of Naples Federico II. Three different pumps, with different specific speeds, have been analyzed. Using the model results, the inverse characteristic and the best efficiency point have been evaluated. Finally, results of this methodology have been compared to prediction methods available in the literature.

A reinforcement learning algorithm is proposed to improve the accuracy of short-term load forecasting (STLF) in this article. The proposed model integrates radial basis function neural network (RBFNN), support vector regression (SVR), and adaptive annealing learning algorithm (AALA). In the proposed methodology, firstly, the initial structure of RBFNN is determined by using SVR. Then, an AALA with time-varying learning rates is used to optimize the initial parameters of SVR-RBFNN (AALA-SVR-RBFNN). In order to overcome the stagnation for searching optimal RBFNN, a particle swarm optimization (PSO) is applied to simultaneously find promising learning rates in AALA. Finally, the short-term load demands are predicted by using the optimal RBFNN. The performance of the proposed methodology is verified on the actual load dataset from Taiwan Power Company (TPC). Simulation results reveal that the proposed AALA-SVR-RBFNN can achieve a better load forecasting precision as compared to various RBFNNs.

This paper presents an overview of the smart electro-clothing systems (SeCSs) targeted at health monitoring, sports benefits, fitness tracking, and social activities. Technical features of the available SeCSs, covering both textile and electronic components, are thoroughly discussed and their applications in the industry and research purposes have been highlighted. In addition, it also presents the developments in the associated areas of wearable sensor systems and textile-based dry sensors. As it became evident during the literature research, such a review on SeCSs covering all relevant issues has not been presented before. This paper will be particularly helpful for new generation researchers investigating the design, development, function and comforts of the sensor integrated clothing materials.

Online transactions are becoming more popular in present situation where the globe is facing an unknown disease COVID-19. Now authorities of Countries requested peoples to use cashless transaction as far as possible. Practically it is not always possible to use it in all transactions. Since number of such cashless transactions have been increasing during lockdown period due to COVID-19, fraudulent transactions are also increasing in a rapid way. Fraud can be analysed by viewing a series of customer transactions data that was done in his/her previous transactions. Normally banks or other transaction authorities warned their customers about the transaction If any deviation is noticed by them from available patterns. These authorities think that it is possibly of fraudulent transaction. For detection of fraud during COVID-19, banks and credit card companies are applying various methods such as data mining , decision tree, rule based mining, neural network, fuzzy clustering approach and machine learning methods. These approaches is try to find out normal usage pattern of customers based on their past activities. The objective of this paper is to find out such fraud transactions during such unmanageable situation.Digital payment schemes are often threatened by fraudulent activities. Detecting fraud transaction in during money transfer may save customers from financial loss. Mobile based money transactions are focused in this paper for fraud detection. A Deep Learning (DL) framework is suggested in this paper that monitors and detects fraudulent activities. Implementing and applying recurrent neural network on PaySim generated synthetic financial dataset, deceptive transactions are identified. The proposed method is capable to detect deceptive transactions with an accuracy of 99.87%, F1-Score of 0.99 and MSE of 0.01.

The Internet-of-Things (IoT) triggers new types of cyber risks. Therefore, the integration of new IoT devices and services requires a self-assessment of IoT cyber security posture. By security posture this article refers to the cybersecurity strength of an organisation to predict, prevent and respond to cyberthreats. At present, there is a gap in the state-of-the-art, because there are no self-assessment methods for quantifying IoT cyber risk posture. To address this gap, an empirical analysis is performed of 12 cyber risk assessment approaches. The results and the main findings from the analysis is presented as the current and a target risk state for IoT systems, followed by conclusions and recommendations on a transformation roadmap, describing how IoT systems can achieve the target state with a new goal-oriented dependency model. By target state, we refer to the cyber security target that matches the generic security requirements of an organisation. The research paper studies and adapts four alternatives for IoT risk assessment and identifies the goal-oriented dependency modelling as a dominant approach among the risk assessment models studied. The new goal-oriented dependency model in this article enables the assessment of uncontrollable risk states in complex IoT systems and can be used for a quantitative self-assessment of IoT cyber risk posture.

Considering characteristics of high river density, special underlying surface in plain river network region, and municipal drainage system function, river network drainage unit model is proposed, which is defined as a region surrounded by main river or embankment. Flood storage variety and control projects regulation of small rivers in each unit is simulated. With drainage catchment as an object, according to its drainage capacity, simplified municipal drainage model was developed. Coupling river network drainage unit model, simplified municipal drainage model and 2D flood routing model, urban flood analysis model for plain tidal river network region was developed, which could be applied to analyzing flood from upstream river, storm surge and local rainfall. Demonstration research was carried out in Puxi flood protected area in Shanghai.

The article’s goal is to overview challenges and problems on the way from the state of the art CUDA accelerated neural networks code to multi-GPU code. For this purpose, the authors describe the journey of porting the existing in the GitHub, fully-featured CUDA accelerated Darknet engine to OpenCL. The article presents lessons learned and the techniques that were put in place to make this port happen. There are few other implementations on the GitHub that leverage the OpenCL standard, and a few have tried to port Darknet as well. Darknet is a well known convolutional neural network (CNN) framework. The authors of this article investigated all aspects of the porting and achieved the fully-featured Darknet engine on OpenCL. The effort was focused not only on the classification with the use of YOLO1, YOLO2, and YOLO3 CNN models. They also covered other aspects, such as training neural networks, and benchmarks to look for the weak points in the implementation. The GPU computing code substantially improves Darknet computing time compared to the standard CPU version by using underused hardware in existing systems. If the system is OpenCL-based, then it is practically hardware independent. In this article, the authors report comparisons of the computation and training performance compared to the existing CUDA-based Darknet engine in the various computers, including single board computers, and, different CNN use-cases. The authors found that the OpenCL version could perform as fast as the CUDA version in the compute aspect, but it is slower in memory transfer between RAM (CPU memory) and VRAM (GPU memory). It depends on the quality of OpenCL implementation only. Moreover, loosening hardware requirements by the OpenCL Darknet can boost applications of DNN, especially in the energy-sensitive applications of Artificial Intelligence (AI) and Machine Learning (ML).

The ratio of males to females with ASD is generally quoted as 4:1 though it is believed that there are biases preventing females being diagnosed and that the true ratio is lower. These biases have not been clearly identified or quantified. Starting with a clinical dataset of 1711 children <18 years old four different methods were employed in an inductive study to identify and quantify the biases and calculate the proportion of females missed. A mathematical model was constructed to compare the findings with current published data. The true male to female ratio appears to be 3:4. Eighty per cent of females remain undiagnosed at age 18 which has serious consequences for the mental health of young women.

Corona virus disease (COVID-19) has infected over more than 10 million people around the globe and killed at least 500K worldwide by the end of June 2020. As this disease continues to evolve and scientists and researchers around the world now trying to find out the way to combat this disease in most effective way. Chest X-rays are widely available modality for immediate care in diagnosing COVID-19. Precise detection and diagnosis of COVID-19 from these chest X-rays would be practical for the current situation. This paper proposes one shot cluster based approach for the accurate detection of COVID-19 chest x-rays. The main objective of one shot learning (OSL) is to mimic the way humans learn in order to make classification or prediction on a wide range of similar but novel problems. The core constraint of this type of task is that the algorithm should decide on the class of a test instance after seeing just one test example. For this purpose we have experimented with widely known Generalized Regression and Probabilistic Neural Networks. Experiments conducted with publicly available chest x-ray images demonstrate that the method can detect COVID-19 accurately with high precision. The obtained results have outperformed many of the convolutional neural network based existing methods proposed in the literature.

This paper presents an optimized energy management strategy for Li-ion power batteries used on electric vehicles (EVs) at low temperatures. Under low-temperature environments, EVs suffer a sharp driving range loss resulted from the energy and power capability reduction of the battery. Simultaneously, because of Li plating, battery degradation becomes an increasing concern as temperature drops. All these factors could greatly increase the total vehicle operation cost. Prior to battery charging and vehicle operating, preheating battery to a battery-friendly temperature is an approach to promote energy utilization and reduce total cost. Based on the proposed LiFePO4 battery model, the total vehicle operation cost under certain driving cycles is quantified in the present paper. Then given a certain ambient temperature, a target temperature of preheating is optimized under the principle of minimizing total cost. As for the preheating method, a liquid heating system is also implemented on an electric bus. Simulation results show that the preheating process becomes increasingly necessary with a decreasing ambient temperature; however, the preheating demand declines as driving range grows. Vehicle tests verify that the preheating management strategy proposed in this paper is able to save total vehicle operation cost.

Intracellular aggregates of the alpha-synuclein protein result in cell loss and dysfunction in Parkinson’s disease and atypical parkinsonism, such as multiple system atrophy and dementia with Lewy bodies. Each of these neurodegenerative conditions, known collectively as alpha-synucleinopathies, may be characterized by a different suite of molecular triggers that initiate pathogenesis. The mechanisms whereby alpha-synuclein aggregates in turn mediate cytotoxicity also remain to be fully elucidated. However, recent studies have implicated the cell-to-cell spread of alpha-synuclein as the major mode of disease propagation between brain regions during disease progression. Here, we review the current evidence for different modes of alpha-synuclein cellular release, movement and uptake, including exocytosis, exosomes, tunnelling nanotubes, glymphatic flow and endocytosis. A more detailed understanding of the major modes by which alpha-synuclein pathology spreads throughout the brain may provide new targets for therapies that halt the progression of disease.

This project designed a set of network security mechanisms for cloud applications in VANETs. At present, cloud computing is one of the government’s development priorities in the industry. We divide cloud into public, private, and hybrid clouds in this project. Vehicles or passengers can access road conditions or public transport information through the public cloud; public transportation can access current driving records and users can access relevant enterprise information on the private cloud and hybrid cloud is a combination of public and private clouds. Both cloud computing or VANETs require network and information security. At present, many researches on VANETs security only focus on message communication, and neglect information storage. Researches on cloud computing security only focus on information protection, and neglect user privacy and anonymity. This project designed a set of network and information security mechanisms in line with the requirements of Confidentiality, Authentication, Non-repudiation, Conditional Anonymity, and Conditional Untraceability. This project primarily needs to achieve the following: 1.an authentication mechanism to verify the identity of each other between the passenger and the vehicle and to verify the identity with Single Sign-On; 2. vehicle or user privacy and anonymity, which need to be able to replace the anonymous ID and related parameters for the vehicle or the user; 3. a private communication mechanism, which enables any vehicle or user to communicate privately; and 4. an information security encryption method, which can encrypt the information on a cloud server to avoid unauthorized access by internal personnel or hackers.

M-polynomial of different molecular structures helps to calculate many topological indices. A topological index of graph G is a numerical parameter related to G which characterizes its molecular topology and is usually graph invariant. In the field of quantitative structure-activity (QSAR) quantitative structure-activity structure-property (QSPR) research, theoretical properties of the chemical compounds and their molecular topological indices such as the Zagreb indices, Randic index, Symmetric division index, Harmonic index, Inverse sum index, Augmented Zagreb index, multiple Zagreb indices etc. are correlated. In this report, we compute closed forms of M-polynomial, first Zagreb polynomial and second Zagreb polynomial of Octagonal network. From the M-polynomial we recover some degree-based topological indices for Octagonal network. Moreover, we give a graphical representation of our results.

A tailored model for the assessment of environmental benefits achievable by “light-weighting” in the automotive field is presented. The model is based on the Fuel Reduction Value (FRV) coefficient, which expresses the Fuel Consumption (FC) saving involved by a 100 kg mass reduction. The work is composed of two main sections: simulation and environmental modelling. Simulation modelling performs an in-depth calculation of weight-induced FC whose outcome is the FRV evaluated for a wide range of Diesel Turbocharged (DT) vehicle case studies. Environmental modelling converts fuel saving to impact reduction basing on the FRVs obtained by simulations. Results show that for the considered case studies, FRV is within the range 0.115–0.143 and 0.142–0.388 L/100 km × 100 kg, respectively, for mass reduction only and powertrain adaptation (secondary effects). The implementation of FRVs within the environmental modelling represents the added value of the research and makes the model a valuable tool for application to real case studies of automotive lightweight LCA.

This study used double-bounded dichotomous-choice to estimate and analyze the factors affecting households’ willingness to pay (WTP) for water quality improvement. This study notes that households with higher income, living near polluted water source, using tap water instead of natural water, who are handicraft producers, and who have more members are willing to pay more. However, households who rarely hear about environmental pollution issues and who are offered a higher bid are more likely to refuse to pay. Solutions to improve water quality are suggested such as to raise people's awareness through communication channels and social organizations; to increase income associated with environmental protection policies; to construct wastewater treatment plants; to encourage the relocation of production establishments to industrial parks and industrial complexes; to put regulations on collection, payment and sanctions in case of not declaring and paying fees into village conventions; to promulgate circulars, and bylaws to concretize and simplify regulations and policies of the Government, Ministry of Natural Resources and Environment.

Clock Network Design (CDN) is a critical step while designing any Integrated-Circuits (ICs). It holds vital importance in the performance of entire circuit. Due to continuous scaling, 3D ICs stacked with TSV are gaining importance, with an objective to continue with the Moore's law. Through-Silicon-Via (TSV) provides the vertical interconnection between two die, which allows the electrical signal to flow through it. 3D ICs has many advantages over conventional 2D planar ICs like reduced power, area, cost, wire-length etc. The proposed work is mainly focused on power reduction and obstacle avoidance for 3D ICs. Various techniques have already been introduced for minimizing clock power within specified clock constraints of the 3D CND network. Proposed 3D Clock Tree Synthesis (CTS) is a combination of various algorithms with an objective to meet reduction in power as well as avoidance of obstacle or blockages while routing the clock signal from one sink to other sink. These blockages like RAM, ROM, PLL etc. are fixed during the placement process. The work is carried out mainly in three steps- first is Generation of 3D Clock tree avoiding the blockages, then Buffering and Embedding and finally validating the results by SPICE simulation. The experimental result shows that our CTS approach results in significant 9% reduction in power as compare to the existing work.

In this study we discuss critical issues in modelling the structure and function of lymph nodes (LNs), with emphasis on how LN physiology is related to its multi-scale structural organization. In addition to macroscopic domains such as B-cell follicles and the T cell zone, there are vascular networks which play a key role in the delivery of information to the inner parts of the LN, i.e., the conduit and blood microvascular networks. We propose object-oriented computational algorithms to model the 3D geometry of the fibroblastic reticular cell (FRC) network and the microvasculature. Assuming that a conduit cylinder is densely packed with collagen fibers, the computational flow study predicted that the diffusion should be a dominating process in mass transport than convective flow. The geometry models are used to analyze the lymph flow properties through the conduit network in unperturbed- and damaged states of the LN. The analysis predicts that elimination of up to 60–90 % of edges is required to stop the lymph flux. This result suggests a high degree of functional robustness of the network.

Smart buildings concept aims at the use of the smart technology to reduce energy consumption as well as improvement of the comfort conditions and users’ satisfaction. It is based on the use of smart sensors to follow both outdoor and indoor conditions as well as software for the control of comfort and security devices. The optimal control of the energy devices requires software for indoor temperature forecasting. This paper presents an ANN – based model for the indoor temperature forecasting. The model is developed using data recoded in an old building of the engineering school Polytech’Lille. Data covered both indoor and outdoor conditions. Analysis of the relevance of the input parameters allowed to develop a simplified forecasting model of the indoor temperature that uses only the outdoor temperature as well as the history of the façade temperature as input parameters. The paper presents successively, data collection, the ANN concept used in the temperature forecasting, and finally the ANN model developed for the façade and indoor forecasting. It shows that an ANN-based model using outdoor and façade temperature sensors provides a good forecasting of the indoor temperature. This model could be used for the optimal control of buildings energy devices.

Vehicle to vehicle (V2V) and Vehicle to infrastructure (V2I) or briefly V2X communications are the one of hot topics in automotive industry. Therefore, this situation is providing many advantages of connected vehicles and infrastructures which bring to human life. For instance, vehicles and road infrastructures which shares information with each other, provides a neat flow regulation, more ordered traffic flow and therefore jammed traffic dependent accident’s percentage will be decreased. On the other hand, security is the most important issue for these systems because the operation of V2X networks is completely dependent on uninterrupted and accurate information sharing. In the light of these information, in this paper we review security issues and current solution architectures. We also propose some open problems in this lively field.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

The purpose of this study is to check out the involvement of entropy in Mpemba effect. Provided that preheating of the water the cooling duration is reduced, we theoretically show that water gains more entropy when warmed and re-cooled to the original temperature.

In the era when the market segment of Internet of Things (IoT) tops the chart in various business reports, it is apparently envisioned that the field of medicine expects to gain a large benefit from the explosion of wearables and internet-connected sensors that surround us to acquire and communicate unprecedented data on symptoms, medication, food intake, and daily-life activities impacting one’s health and wellness. However, IoT-driven healthcare would have to overcome many barriers, such as: 1) There is an increasing demand for data storage on cloud servers where the analysis of the medical big data becomes increasingly complex; 2) The data, when communicated, are vulnerable to security and privacy issues; 3) The communication of the continuously collected data is not only costly but also energy hungry; 4) Operating and maintaining the sensors directly from the cloud servers are non-trial tasks.This book chapter defined Fog Computing in the context of medical IoT. Conceptually, Fog Computing is a serviceoriented intermediate layer in IoT, providing the interfaces between the sensors and cloud servers for facilitating connectivity, data transfer, and queryable local database. The centerpiece of Fog computing is a low-power, intelligent, wireless, embedded computing node that carries out signal conditioning and data analytics on raw data collected from wearables or other medical sensors and offers efficient means to serve telehealth interventions. We implemented and tested an fog computing system using the Intel Edison and Raspberry Pi that allows acquisition, computing, storage and communication of the various medical data such as pathological speech data of individuals with speech disorders, Phonocardiogram (PCG) signal for heart rate estimation, and Electrocardiogram (ECG)-based Q, R, S detection. The book chapter ends with experiments and results showing how fog computing could lessen the obstacles of existing cloud-driven medical IoT solutions and enhance the overall performance of the system in terms of computing intelligence, transmission, storage, configurable, and security. The case studies on various types of physiological data shows that the proposed Fog architecture could be used for signal enhancement, processing and analysis of various types of bio-signals.

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

Deep learning (DL), which is originated from an artificial neural network (ANN), is one of the major technologies of today's smart cybersecurity systems or policies to function in an intelligent manner. Popular deep learning techniques, such as Multi-layer Perceptron (MLP), Convolutional Neural Network (CNN or ConvNet), Recurrent Neural Network (RNN) or Long Short-Term Memory (LSTM), Self-organizing Map (SOM), Auto-Encoder (AE), Restricted Boltzmann Machine (RBM), Deep Belief Networks (DBN), Generative Adversarial Network (GAN), Deep Transfer Learning (DTL or Deep TL), Deep Reinforcement Learning (DRL or Deep RL), or their ensembles and hybrid approaches can be used to intelligently tackle the diverse cybersecurity issues. In this paper, we aim to present a comprehensive overview from the perspective of these neural networks and deep learning techniques according to today's diverse needs. We also discuss the applicability of these techniques in various cybersecurity tasks such as intrusion detection, identification of malware or botnets, phishing, predicting cyber-attacks, e.g. denial of service (DoS), fraud detection or cyber-anomalies, etc. Finally, we highlight several research issues and future directions within the scope of our study in the field. Overall, the ultimate goal of this paper is to serve as a reference point and guidelines for the academia and professionals in the cyber industries, especially from the deep learning point of view.

Integration of multi-view datasets which are comprised of heterogeneous sources or different representations is challenging to understand the subtle and complex relationship in data. Such data integration methods attempt to combine efficiently the complementary information of multiple data types to construct a comprehensive view of underlying data. Nonnegative matrix factorization (NMF), an approach that can be used for signal compression and noise reduction, has aroused widespread attention in the last two decades. The Kullback–Leibler divergence (or relative entropy) information distance can be used to measure the loss function of NMF. In this article, we propose a fast and robust framework (RSNMF) based on symmetric nonnegative matrix factorization (SNMF) and similarity network fusion (SNF) for clustering human microbiome data including functional, metabolic and phylogenetic profiles. Many existing methods typically utilize all the information provided by each view to create a consensus representation, which often suffers a lot from noise in data and cannot provide a precise representation of the latent data structures. In contrast, RSNMF combines the strength of SNMF and the advantage of SNF to form a robust clustering indicator matrix thus can reduce the noise influence. We conduct experiments on one synthetic and two real dataset (microbiome data, text data) and the results show that the proposed RSNMF has better performance over the baseline and the state-of-art methods, which demonstrates the potential application of RSNMF for microbiome data analysis.

Since the beginning of 2020, tetracycline (TC), such as minocycline (MINO), has been used to inhibit coronavirus disease 2019 (COVID-19). Traditional Japanese Kampo medicine, such as Saiko-keishi-to (SKT), has recently received a lot of attention for its anti-severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) effects. We describe a COVID-19 patient treated with MINO and SKT in anticipation of their anti-SARS-CoV-2 properties. A 90-year-old male patient with Alzheimer’s disease was referred to a medical clinic due to fever, appetite loss, and general malaise. Based on positive SARS-CoV-2 rapid antigen tests, he was diagnosed with COVID-19. He did not have COVID-19 pneumonia, but he had difficulty in eating on his own. As a result, he was referred to a hospital for admission. After admission, he was treated with molnupiravir to avoid aggravation. Seven days after his admission, he was discharged. After his discharge, he was referred to our hospital as an outpatient due to a prolonged mild fever and general malaise. As a precaution, a real-time reverse transcription-polymerase chain reaction (RT-PCR) test was performed, which yielded a positive result. Therefore, the aforementioned symptoms were thought to be caused by prolonged COVID-19. He was treated with MINO and SKT due to the anti-viral properties of these two drugs. The RT-PCR test became negative 7 days after receiving this treatment, and the fever and general malaise subsided.

UAV photogrammetry development during the last decade has allowed to catch information at a very high spatial and temporal resolution from terrains with very difficult or impossible human access. This paper deals with the application of these techniques to study and produce information of very extreme topography which is useful to plan works on this terrain or monitoring it over the time to study its evolution. The methodology stars with the execution of UAV flights on the cut slope studied, one with the cam vertically oriented and other at 45º respect that orientation. Ground control points (GCPs) and check points (CPs) were measured for georeference and accuracy measurement purposes. Orthophoto was obtained projecting on a fitted plane to a studied surface. Moreover, since a digital surface model (DSM) is not able to represent faithfully that extreme morphology, information to project works or monitoring it has been derived from the point cloud generated during the photogrammetric process. An informatics program was developed to generate contour lines and cross sections derived from the point cloud, which was able to represent all terrain geometric characteristics, like several Z coordinates for a given planimetric (X, Y) point. Results yield a root mean square error (RMSE) in X, Y and Z directions of 0.053 m, 0.070 m and 0.061 m respectively. Furthermore, comparison between contour lines and cross sections generated from point cloud with the developed program on one hand and those generated from DSM on other hand, shown that the former are capable of representing terrain geometric characteristics that the latter cannot. The methodology proposed in this work has been shown as an adequate alternative to generate manageable information, as orthophoto, contour lines and cross sections, useful for the elaboration, for example, of projects for repairing or maintenance works of cut slopes with extreme topography.

The critical hypoxia in COVID-19 patients during this pandemic, has taken away many lives all around the globe. The mechanism has been poorly understood and initially, word got around that it was a SARS (Severe Acute Respiratory Syndrome) pneumonia. The atypical images in lung computerized axial tomography (CAT) scans were alarming. This immediately alerted everyone including poor countries to purchase lacking sophisticated ventilator equipment. However, in some countries, even 88% of the patients on ventilators lost their lives. New observations and pathological findings are gradually clarifying the disease. What seems evident is that it is not only one disease but several, with different responses in different countries and different altitudes. The critical hypoxia and «gasping» present in some patients are not totally understood. It was mentioned that it could be like a High-Altitude Pulmonary Edema (HAPE). Hereby, as high-altitude medicine and hypoxia physiology specialists, we compare the pathophysiology with that of high-altitude exposure in order to understand the mechanisms involved. Some differences in lung radiological images along with transmission and viral attack mechanisms are discussed. The oxygen transport triad used at high-altitude can be applied on this pathology in order to propose even the use of erythropoietin (EPO) early in the treatment. The immune system is the most important long-term survival tool, so we suggest a short-term strategy: the use of special Earth open-circuit astronaut-resembling suits with effective outside air filtering re-breathing mechanisms in order to return to work and daily activities, without contamination risk. Thereby, the curve can be flattened without quarantine and the economy could recover.

The application of the sensors optical fiber in the areas of scientific instrumentation and industrial instrumentation is very attractive due to its numerous advantages. In the industry of civil engineering for example, quasi-distributed sensors made with optical fiber are used for reliable strain and temperature measurements. Here, a quasi-distributed sensor in the frequency domain is discussed. The sensor consists of a series of low-finesse Fabry-Perot interferometers where each Fabry-Perot interferometer acts as a local sensor. Fabry-Perot interferometers are formed by pairs of identical low reflective Bragg gratings imprinted in a single mode fiber. All interferometer sensors have different cavity length, provoking the frequency-domain multiplexing. The optical signal represents the superposition of all interference patterns which can be decomposed using the Fourier transform. The frequency spectrum is analyzed and sensor´s properties were defined. Following, a quasi-distributed sensor was numerically simulated. Our sensor simulation considers sensor properties, signal processing, noise system and instrumentation. The numerical results show the behavior of resolution vs. signal-to-noise ratio. From our results, the Fabry-Perot sensor has high resolution and low resolutions. Both resolutions are conceivable because the FDPA algorithm elaborates two evaluations of Bragg wavelength shift

Geospatial Information Systems (GIS) can provide a great environment for using machine learning algorithm for spatial data such as satellite images. Integrating this functionality with artificial intelligence algorithms for analyzing spatial data enables us to predict challenging disasters such as deforestation. Deforestation as an environmental problems has been recorded the most serious threat to environmental diversity and one of the main components of land-use change. In this paper, we investigate spatial distribution of deforestation using artificial neural networks and satellite imagery. We modeled deforestation process using various factors in determining the relationship between deforestation and environmental and socioeconomic factors. Hence, for this purpose, the proximity to roads and habitats, fragmentation of the forest, height from sea level, slope, and soil type are considered in the model. In this research, we modeled land cover changes (forests) to predict deforestation using an artificial neural network due to its significant potential for the development of nonlinear complex models. The procedure involves image registration and error correction, image classification, preparing deforestation maps, determining layers, and designing a multi-layer neural network to predict deforestation. The satellite images for this study are of a region in Hong Kong which are captured from 2012 to 2016. The results of the study demonstrate that neural networks approach for predicting deforestation can be utilized and its outcomes show the areas that destroyed during the research period.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

Multi-stakeholder based construction projects are subject to various risk factors due to dynamic business environments. These risks affect project activities which indirectly impact construction costs, resulting in delays and poor building quality. So, managing these project risks requires suitable risk mitigation strategies to evaluate and analyse their severity. Hence, risk evaluation and assessment of construction projects is a multi-criteria decision making (MCDM) problem. In present real-life problems, evaluation of project risks is often uncertain and even incomplete, and the prevailing methodologies fail to handle such situations. To address the problem, this paper extends the analytical network process (ANP) methodology in the D number domain to handle three types of ambiguous evaluations, viz. complete, uncertain, and incomplete, and assesses the weight of risk criteria. The D number based approach overcomes the deficiencies of the exclusiveness hypothesis and completeness constraint of Dempster-Shafer (D-S) theory. Here, preference ratings of the decision matrix for each decision-maker are determined using a D number extended consistent fuzzy preference relation (D-CFPR). An extended multi-attributive border approximation area comparison (MABAC) method in D number is then developed to rank and select the best alternative risk response strategy. Finally, an illustrative example from construction sector is presented to check the feasibility of the proposed approach. For checking the reliability of alternative ranking, a comparative analysis is performed with different MCDM approaches (D-COPRAS, D-ARAS, D-MABAC, and D-TOPSIS). Based on different criteria weights, a sensitivity analysis of obtained ranking of the hybrid D-ANP-MABAC model is performed for verify the robustness of the proposed method.

We propose the traditional goal of cancer therapists to develop a single drug or drug combination that can, by itself, eliminate all cancer cells within a host has neglected potential treatments that may achieve curative outcomes by strategically combining agents that are individually effective but non-curative. We derive basic principles for such an approach from the eco-evolutionary dynamics of background extinctions in which a “first strike” reduces the size and heterogeneity of the initial population and is followed immediately by demographic and ecological “second strikes” that push the population below an extinction threshold. This proposed strategy appears identical to the empirically-derived curative therapy in childhood Acute Lymphocytic Leukemia.

Timely detection of surface damages on wind turbine blades is imperative for minimising downtime and avoiding possible catastrophic structural failures. With recent advances in drone technology, a large number of high-resolution images of wind turbines are routinely acquired and subsequently analysed by experts to identify imminent damages. Automated analysis of these inspection images with the help of machine learning algorithms can reduce the inspection cost, thereby reducing the overall maintenance cost arising from the manual labour involved. In this work, we develop a deep learning based automated damage suggestion system for subsequent analysis of drone inspection images. Experimental results demonstrate that the proposed approach could achieve almost human level precision in terms of suggested damage location and types on wind turbine blades. We further demonstrate that for relatively small training sets advanced data augmentation during deep learning training can better generalise the trained model providing a significant gain in precision.

Food waste is one of the greatest challenge to sustainability in developed and developing countries. In the former, food waste is concentrated in the final part of the chain. Too Good To Go is a digital platform aimed to prevent food waste, where consumers can buy magic boxes from different outlets containing food products that are approaching their end-of-life. However, the mechanism of the platform enable the outlets to publish their offering much in advance of the pick-up time, raising the question whether the food sold on the platform is effectively a leftover or a planned production. Our empirical study gathers data from over 1200 outlets in Rome on the Too Good To Go platform.

The emerging use of visualization techniques in pathology and microbiol- ogy has been accelerated by machine learning (ML) approaches towards image preprocessing, classification, and feature extraction in an increasingly complex series of datasets. Modern Convolutional Neural Network (CNN) architectures have developed into an umbrella of vast image reinforcement and recognition methods, including a combined classification-localization of single/multi-object featured images. As a subtype neural network, CNN cre- ates a rapid order of complexity by initially detecting borderlines, edges, and colours in images for dataset construction, eventually capable in mapping intricate objects and conformities. This paper investigates the disparities between Tensorflow object detection APIs, exclusively, Single Shot Detector (SSD) Mobilenet V1 and the Faster RCNN Inception V2 model, to sample computational drawbacks in accuracy-precision vs. real time visualization capabilities. The situation of rapid ML medical image analysis is theoretically framed in regions with limited access to pathology and disease prevention departments (e.g. 3rd world and impoverished countries). Dark field mi- croscopy datasets of an initial 62 XML-JPG annotated training files were processed under Malaria and Syphilis classes. Model trainings were halted as soon as loss values were regularized and converged.

This paper presents a microgrid distributed energy resources (DERs) for a rural standalone system. It is made up of solar photovoltaic (solar PV) system, battery energy storage system (BESS), and wind turbine coupled to permanent magnet synchronous generator (WT-PMSG). The DERs are controlled by maximum power point tracking (MPPT) based proportional intergral (PI) controllers for both maximum power tracking and error feedback compensation. The MPPT uses the perturb and observe (P&O) algorithm for tracking the maximum power point of the DERs. The PI gains are tuned using the Ziegler-Nichol’s method. The developed system was built and simulated in MATLAB/Simulink under two conditions - constant load, and step load changes. The controllers enabled the BESS to charge even during conditions of varying load and other environmental factors such as change of irradiance and wind speed. The reference was tracked very well by the output voltage of the DC grid. This is a useful research for electrifying the rural islanded areas, too far from the grid.

This paper deals with the environmental characterization of a large and densely populated area, with a poor reputation for contamination, considering the contribution of environmental features (air, soil, soil hydraulic and groundwater) and the potential effects on human health. The use of Geographic Information System (GIS) has made possible a georeferenced inventory and, by overlaying environmental information, an operational synthesis of comprehensive environmental conditions. The cumulative effects on environmental features were evaluated, taking into account superposition effects, by means of the spatial multicriteria decision analysis (S-MCDA). The application of the S-MCDA for converging the combination of heterogeneous factors, related to soil, land and water, deeply studied by heterogeneous groups of experts, constitutes the novelty of the paper. The results confirmed an overall higher potential of exposure to contaminants in the environment and higher mortality rates in the study area for some tumours, but hospital admissions for tumours were generally similar to the regional trend. Besides, mortality data may be strictly dependent on the poor socioeconomic conditions, quality of therapy and a lack of welfare in the area relative to the rest of Italy. Finally, as regards the possible relationship between presence of contaminants in the environment and health conditions of the population no definite conclusions can be drawn, although the present study encourages the use of the new proposed methods, that increase the possibilities for studying the combined effect of more environmental factors.

1) Background: It has been more than a decade since the concern about addictive use of the Internet and mobile phones was first expressed and its possible inclusion into the lists of mental disorders has been a popular topic of discussion recently, thus it seems to be a fitting moment to investigate the evolution of this issue over time. The aim of the present study was to analyze the evolution of the perception of problematic Internet and smartphone use in young people over the period 2006–2017; 2) Methods: To this end, a questionnaire on Internet use habits and the CERI and CERM questionnaires on negative consequences of Internet and smartphone use were administered to a sample of 792 university students and compared with data from former studies over the period 2006–2017; 3) Results: The perception of problematic Internet and mobile phone use has increased over the last decade, social networks are considered responsible for this increase, and females are the ones perceived to be more affected than males. The degree to which participants agree with the statement “I am addicted to the Internet” can be used as a screening item for problematic use.

In networked driving simulation, two or more human drivers participate interactively within a shared virtual environment. Thereby, typical applications of driving simulation can be extended to consider multi-driver scenarios, where a much closer approximation of reality with its unpredictability is achieved. However, the utilized network is typically prone to a considerable amount of message traffic. In addition to restricted system scalability, the resulting degradation of network performance leads to invalid simulation outcomes or unacceptable system behavior. High-level architecture (HLA) is an IEEE standard for networked simulation. Data distribution management (DDM) is one of the service groups provided by HLA standard. The aim of the DDM service is to reduce network traffic and to save effort required to process unnecessary received data. However, different approaches for current DDM implementations show major drawbacks in terms of utilization complexity, inefficiency, and yet added network overhead. This paper presents a concept of an interest manager that takes over the DDM functionality and avoids these drawbacks. Simulation data is exchanged between the participating driving simulators only when it is necessary according to the driving situations. The concept is validated by analyzing the network load of two driving maneuvers with and without the interest manager.

Recent methodological advances have enabled researchers to track the network structure of the human brain over time. Together, these studies provide novel insights into effective brain function, highlighting the importance of the systems-level perspective in understanding the manner in which the human brain organizes its activity to facilitate behavior. Here, we review a range of recent fMRI and electrophysiological studies that have mapped the relationship between inter-regional communication and network structure across a diverse range of brain states. In doing so, we identify both behavioral and biological axes that may underlie the tendency for network reconfiguration. We conclude our review by providing suggestions for future research endeavors that may help to refine our understanding of the functioning of the human brain.

HPV vaccine induces a herd immunity effect in genital warts when a large number of the population is vaccinated. That aspect should be taken into account when devising new vaccine strategies, like vaccination at older ages or male vaccination. Therefore it is important to develop mathematical models with good predictive capacities. We devised a sexual contact network that was calibrated to simulate the Spanish epidemiology of different HPV genotypes. Through this model we simulated the scenario that occurred in Australia in 2007, where 12-13 year-old girls where vaccinated with a three-dose schedule of a vaccine containing genotypes 6 and 11, that protect against genital warts, and also a catch-up program in women up to 26 years of age. Vaccine coverage were 73 % in girls with three doses and with coverage rates decreasing with age until 52 % for 20-26 year-olds. A fast 59 % reduction in the genital warts diagnoses occurred in the model in the first years after the start of the program, similar to what was described in the literature.

Whereas waste management research has focused on mostly urban municipalities in South Africa, not much is known about the current performance of waste management services from the perspective of community residents in rural municipalities. This study reports on the status and effectiveness of waste management practices from the perspective of community residents in the Umkhanyakude and Zululand Districts in the rural areas of the KwaZulu-Natal province of South Africa. Making use of structured questionnaires, primary data was obtained by interviewing 333 respondents representing households in the study area. Results have revealed several shortfalls in the provision of municipal waste management services, except for solid waste removal from households (66%), and management of landfill sites (41%). The degree of dissatisfaction for waste management services rendered was very high (97.3%). Furthermore, the majority (61.4%) of respondents were not willing to participate in waste segregation due to lack of appropriate knowledge and infrastructure. The study also pinpointed some benefits associated with waste minimization, as well as barriers constraining effective waste recycling. Based on these findings, there is a dire need for transforming current waste management practices toward increased recycling rates by creating more environmental awareness and a supporting infrastructure.

This study uses data from the pilot project "Community Monitoring for Better Health and Education Services Delivery Project'' in Burkina Faso, to model the joint impact of generic essential drugs and nursing staff supplies constraints on access to primary health care in the country. The results show that statistical endogeneity of supply side constraints are present in the standard univariate probit specification of access to care. However, when accounted for, the resulting Trivariate Probit model shows that although shortages of generic essential drugs supply do not seem to constitute a significant barrier to access in Burkina Faso, shortages in nursing staff supply do. In fact, the likelihood of primary care access is reduced by 85.5% among those that reported having experienced a shortage in nursing staff, while paradoxically increasing by 60.3% among those that reported having experienced a shortage in generic essential drugs. A potential explanation for these findings is that overall the health care needs in the three surveyed regions in the country were more linked to primary health care services consumption from nurses, although further research would be important to clearly elucidate the position of health goods such as generic essential drugs.