We compare photoaligning properties of polymer layers fabricated from the same constituents: polymethyl-methacrylate (PMMA) and azo-dye Disperse Red 1 (DR1), either chemically attached to the PMMA main-chain, or physically mixed with it. Photoaligning properties depend on the preparation method drastically. This finding is supported by atomic force microscope (AFM) scans monitoring the light-induced changes at the polymer−air interface, and revealing a photoinduced mass transfer.

At present, aeroponic control is mainly regulated according to the environmental factors of aeroponics, such as the temperature, humidity, light intensity, carbon dioxide concentration, pH, and electrical conductivity (EC) of the nutrient solution. There is a lack of knowledge available in the literature for an aeroponic control system for plant growth information as the primary feedback signal. Therefore, a fuzzy logic-controlled aeroponics system was developed for the growth of lettuce as a feedback signal. After designing, the effectiveness test of system was performed with experiment having three treatments T1 (180C), T2 (220C) and without control (CK). The results show an increasing trend in shoot length, root length, and shoot area over time in all treatments. In terms of shoot area, the maximum of 345 cm² was observed in the T1 treatment, while the CK treatment had a minimum of 241.8 cm². Statistical analysis indicated that the T1 and T2 treatments were not significantly different, but both were significantly different from the CK treatment. The study demonstrates the effectiveness of the fuzzy logic control system and an 18°C nutrient solution temperature, resulting in improved lettuce growth and reduced root-to-shoot ratio. The findings suggest the potential of using fuzzy logic control in aeroponics for optimized cultivation outcomes.

Structural health monitoring (SHM) is critical for ensuring the safety of infrastructures like bridges. This article presents a digital twin solution for SHM of railway bridges using low-cost wireless accelerometers and Machine Learning (ML). The system architecture combines edge on-premises computing and cloud analytics to enable efficient real-time monitoring and complete storage of relevant time-history datasets. After train crossings, accelerometers stream raw vibration data, which is processed in the frequency domain and analyzed via machine learning to detect anomalies indicating potential structural issues. The digital twin approach is demonstrated on an in-service railway bridge, where vibration data was collected over two years under normal operating conditions. By learning allowable ranges for vibration patterns, the digital twin model identifies abnormal spectral peaks, suggesting changes in structural integrity. The long-term pilot proves that this affordable SHM system can provide automated and real-time warning of bridge damage and also supports the use of in-house designed sensors of lower-cost and edge computing capabilities than those used in the demonstration. The successful on-premises-cloud hybrid implementation provides a cost effective and scalable model for expanding monitoring to thousands of railway bridges, democratizing SHM to improve safety by avoiding catastrophic failures.

A detailed literature review is performed in this study to address solutions for the full-body design and control of an aerial manipulator. Deep Reinforcement Learning methods are growing to be utilized recently to cope with various uncertainties. The pros and cons of these theories will be explained as well as introducing the advantages of Fuzzy Reinforcement Learning methods. State-of-the-Art, possible challenges, potential approaches, and a summary of desired precision devices are discussed in this study.

Microelectromechanical System (MEMS) vibrating gyroscope design considerations are always intriguing due to their microscale mechanical, electrical, and material behavior. MEMS vibrating ring gyroscopes have become important inertial sensors in inertial measurement units (IMU) for navigation and sensing applications. The design of a MEMS vibrating ring gyroscope incorporates an oscillating ring structure as a proof mass, reflecting unique design challenges and possibilities. This paper presents a comprehensive design analysis of the MEMS vibrating ring gyroscope from the mechanical, electrical, and damping perspectives. The mechanical design of the MEMS vibrating ring gyroscope investigates the various frame designs of the vibrating ring structure, as well as the various beam structures, including curved, rectangular, and semicircular beam structures, which are analyzed using mathematical models and finite element analysis (FEA) simulations that provide an in-depth analysis of the stiffness and deflection of the vibrating structures. The electrical designs of the MEMS vibrating ring gyroscope were analyzed using various electrode configurations, electrostatic actuation, and capacitive detection mechanisms, respectively. The design analysis of various forms of damping, including viscous, structural, thermoelastic, and anchor damping, has been discussed. The variety of design structures investigated for MEMS vibrating ring gyroscopes' mechanical, electrical, and damping performance.

The application of movement-detection sensors is crucial for understanding surface movement and tectonic activities. The development of modern sensors has been instrumental in earthquake monitoring, prediction, early warning, emergency commanding and communication, search and rescue, and life detection. There are numerous sensors currently being utilized in earthquake engineering and science. It is essential to review their mechanisms and working principles thoroughly. Hence, we have attempted to review the development and application of these sensors by classifying them based on the timeline of earthquakes, physical or chemical mechanisms of sensors, and location of sensor platforms. In this study, we analyzed all available sensor platforms that have been widely used in recent years, with satellites and UAVs being among the most used. The findings of our study will be useful for future earthquake response and relief efforts, as well as research aimed at reducing earthquake disaster risks.

The utilization of smart IoT devices, commonly referred to as digital twins, is aimed at the digitalization of human knowledge within aquaculture processes. This involves the incorporation of cutting-edge technologies, including information-based management with big data and modeling, to automate machinery and gain comprehensive insights into the aquaculture environment and fish farm conditions. The ultimate objective is to empower farmers to make informed decisions, furnishing them with objective data to enhance their capacity in monitoring and controlling the various factors impacting fish production. As a result, farming decisions can be fine-tuned to enhance fish health and optimize farm output. In the context of large and modern aquaculture farms, technological innovation becomes imperative to automate processes, minimize labor requirements, and streamline fish feeding operations. Remarkably, the literature currently offers limited discussions on the digital transformation of aquaculture through the application of digital twin methodologies. A prior study underscores the critical influence of factors such as market prices and fish survival rates on the profitability of offshore caging culture. In this study, we embark on an analysis of the prerequisites for establishing a digital twin infrastructure tailored to intelligent fish feeding management. This infrastructure is designed to facilitate the integration of technology and data-driven decision-making, ultimately enhancing the efficiency of fish feeding processes. The proposed architecture for the fish feeding digital twin encompasses various digital twin components, encompassing water quality forecasting, fish population assessment, fish metrics estimation, fish feed prediction, and evaluation of fish feeding intensity. Furthermore, we optimize the daily fish feeding process through reinforcement learning algorithms. Finally, we implement a cloud-based AIoT system that provides the runtime environment for executing digital twins and controlling our intelligent fish feeding machinery. Experimental findings underscore the efficacy of the proposed digital twin system in significantly improving traditional fish feeding processes, notably in terms of reducing food costs and labor requirements.

To monitor adherence to diets and to design and evaluate nutritional interventions it is essential to obtain objective knowledge about eating behavior. In most research, measures of eating behavior are based on self-reporting, such as 24-h recalls, food records (food diaries), and food frequency questionnaires. Self-reporting is prone to inaccuracies due to inaccurate and subjective recall and other biases. Recording behavior using non-obtrusive technology in daily life would overcome this. We here provide an up-to-date systematic overview encompassing all (close-to) publicly or commercially available technologies to automatically record eating behavior in real-life settings. 1328 studies were screened and after applying defined inclusion and exclusion criteria, 122 studies were included for in-depth evaluation. Technologies in these studies were categorized by what type of eating behavior they measure and which type of sensor technology they use. In general, we found that relatively simple sensors are often used. Depending on the purpose, these are mainly motion sensors, microphones, weight sensors, and photo cameras. While several of these technologies are commercially available, there is still a lack of publicly available algorithms that are needed to process and interpret the resulting data. We argue that future work should focus on developing robust algorithms and validating these technologies in real-life settings. Combining technologies (e.g., prompting individuals for self-reports at sensed, opportune moments) is a promising route toward ecologically valid studies of eating behavior.

In the field of embedded systems, energy efficiency is a critical requirement, particularly for battery-powered devices. RISC-V processors have gained popularity due to their flexibility and open-source nature, making them an attractive choice for embedded applications. However, not all RISC-V processors are equally energy-efficient, and it is important to evaluate their performance in specific use cases. This paper evaluates the energy consumption and resource utilization of a new RISC-V processor, RisCO2, and four existing processors - Zero-riscy, Micro-riscy, Ri5cy, and CV32E40P - in a signal demodulation application for NDIR CO2 sensors. The processors were implemented in the PULPino SoC and synthesized using Vivado IDE. The processor named RisCO2 is based on the RV32E_Zfinx instruction set and was designed from scratch by the authors specifically for low-power signal processing applications such as signal demodulation in CO2 NDIR sensors. The other processors are Ri5cy, Micro-riscy, and Zero-riscy, developed by the PULP Platform team, and CV32E40P (derived from Ri5cy) from the OpenHW Group, all of them widely used in the RISC-V community. Our experiments showed that RisCO2 had the lowest energy consumption among the five processors, with a 53.5% reduction in energy consumption compared to CV32E40P and a 94.8% reduction compared to Micro-riscy. Additionally, RisCO2 had the lowest FPGA resource utilization compared to the best-performing processors, CV32E40P and Ri5cy, with a 46.1% and a 59% reduction in LUTs, respectively. Our findings suggest that RisCO2 is a highly energy-efficient RISC-V processor for NDIR CO2 sensors that require signal demodulation. The results also highlight the importance of evaluating processors in specific use cases to identify the most energy-efficient option. This paper provides valuable insights for designers of energy-efficient embedded systems using RISC-V processors.

A 3D graphene foam made of interconnected multilayer graphene flakes was produced on optical fibres (OF) by laser-induced transformation of a polyimide (PI) film coated on the OF cladding. This material, known as la-ser-induced graphene (LIG), was explored in the electrochemical detection and quantification of dopamine (DA) at physiologically relevant concentrations in the presence of the most relevant interfering molecules in biological fluids, ascorbic acid (AA) and uric acid (UA). The measured limit of detection is 100 nM, the linear range is 0.1 to 5 μM and a maximum sensitivity of 5.0 µA µM−1 cm−2 was obtained for LIG decorated with Pt nanoparticles (NPs). Moreover, immunity to AA and UA interference and to fouling was attained by decorating the LIG elec-trode with Pt NPs and coating with Nafion. These figures of merit underlines the potential of these sensors for the quantification of physiologically relevant concentrations of DA in biological fluids, paving the way for the development of hybrid electrochemical/optical sensing actuating platforms in a lab-on-fibre configuration, with relevant applications in biomedical engineering. The advantages of this hybrid arrangement include the possi-bility of in-situ counterproofing, extended measuring ranges, photoelectrochemical detection and the probing of inaccessible places. This elegant approach can also provide a simple and cost-effective way to fabricate biomed-ical devices with extended functionality, such as medical optical probes with added electrochemical capabilities, optogenetics combined with local electrochemical detection, among others.

Glass has emerged as a highly versatile substrate for various sensor and MEMS packaging applications, including electromechanical, thermal, optical, biomedical, and RF devices, due to its exceptional properties such as high geometrical tolerances, outstanding heat and chemical resistance, excellent high-frequency electrical properties, and the ability to be hermetically sealed. In these applications, Through-Glass-Via (TGV) plays a vital role in manufacturing and packaging by creating electrical interconnections through glass substrates. This paper provides a comprehensive summary of the research progress in TGV fabrication along with their integrations, including through-via formation and metallization. The paper also reviews the significant qualification and reliability achievements obtained by the scientific community for TGV. Additionally, the paper summarizes the application of TGV technology in various sensors.

Near-neutral pH and low redox potentials (EH) are considered favorable conditions for radionuclides immobilization in deep repository systems in clay geological formations. Cigeo is a future Industrial Centre for Geological Disposal for Nuclear Waste (NW) for high-level and intermediate level long-lived radioactive waste, to be built in France, at 500 m depth within the Callovo-Oxfordian clay formation. Deep knowledge of the mechanisms and kinetics of corrosion occurring at the external surface of tubings made of API 5L X65 carbon steel (CS-X65) in contact with COx pore water, is essential for a reversible NW management of the Cigeo site. By using robust handmade electrodes and electrochemical and gravimetric techniques, this work aimed to determine the corrosion phenomenology and kinetics of CS-X65 in contact with COx pore water flowing continuously through a Multi-Parameter Probe (MPP) device, placed at 500 m depth, for more than 180 days. It also aimed at demonstrating the reliability and the robustness of the measurement methodology for the corrosion evaluation of the metallic liner of the future nuclear waste disposal site. Two iron oxidants were encountered, oxygen, who was depleted, and proton, who was accompanied by hydrogen sulfide. Corrosion mechanisms and kinetics were well established for two CS-X65, electrochemically perturbed and not. The corrosion thickness loss rates stand between 0.016 and 0.032 mm/y.

Buildings are rapidly becoming more digitized, to a large extent due to developments in IoT. This will provide many opportunities but also a number of challenges. One of the central challenges in the process of digitizing buildings is the ability to monitor the building’s status effectively. This monitoring is essential for various services that rely on information about the presence and activities of individuals within different areas of the building. Occupancy information, including people counting, occupancy detection, location tracking, and activity detection, plays a vital role in the management of smart buildings. In this article, our primary focus is on the use of Passive Infrared (PIR) sensors for gathering occupancy information. PIR sensors are among the most widely used sensors for this purpose due to their consideration of privacy concerns, cost-effectiveness, and low processing complexity compared to many others. Despite numerous literature review articles in the field of occupancy information, there currently isn’t a specialized literature review dedicated to occupancy information derived specifically from PIR sensors.Therefore, this study analyzes articles that specifically explore the application of PIR sensors for occupancy information. This article provides a comprehensive literature review of PIR sensor technology from 2015 to 2023, with a focus on applications in people counting, activity detection, and localization (traking and location). It consolidates findings from a number of articles that have explored and enhanced the capabilities of PIR sensors in these interconnected domains. This review thoroughly examines the application of various techniques, machine learning algorithms, and configurations for PIR sensors in indoor building environments, emphasizing not only the data processing aspects but also their advantages, limitations, and efficacy in producing accurate occupancy information.These developments are crucial for improving building management systems in terms of energy efficiency, security, and user comfort, among other operational aspects.These developments are crucial for improving building management systems in terms of energy efficiency, security, and user comfort, among other operational aspects. The paper seeks to offer a thorough analysis of the present state and potential future advancements of PIR sensor technology in efficiently monitoring and understanding occupancy information by classifying and analyzing improvements in these domains.

The paper presents the final results from the research project “Urban Abacus of Building Energy performances (Abaco Urbano Energeticodegli Edifci – AUREE)” aimed at supporting the renovation and energy efficiency enhancement of urban building heritage financed by the “Ricerca Sistema Elettrico (MISE) program”. The crux of AUREE project is a Web – GIS GeoBlog portal with customized semantic dashboards aimed at sharing information on urban built environment and promoting the participation of local stakeholders to its improvement. As the latest development of this research, a workflow integrating the AUREE portal with BIM authoring and an open source IoT platform has been implemented and applied to an experimental case study concerning a public building in Carbonia (Italy). The headquarters of the sustainable energy research center Sotacarbo was selected as case study. The presented results proved that it was possible to create an open system, which could be easily consulted by "non-expert" users as well, to make available real-time monitoring data obtained from IoT sensors measuring the energy consumption, the indoor environmental conditions and the usage profiles of public buildings. The proposed open system could also be suitable to be later used as an effective tool to support the rising “energy communities”.

Machine Learning can be used for social good. In this paper, we discuss how it can be used to combat climate change and facilitate land management and farming in developing countries and in particular in Côte d’Ivoire. This paper explores models that improve land and water management and agricultural farming cultivation to contrast climate change. Côte d’Ivoire is the largest producer of cocoa beans (43%) in the world, but deforestation, lack of rainfall, drought, and climate change threaten crops and the already fragile economy of Ivorian farmers. It is important to combat climate change with methods and techniques that are affordable to the local farmers and also induce positive effects in production. We discuss the use of low-cost sensors to collect data on the soil and open data and open source software to develop AI tools. We show that using deep neural networks (YOLOv5m) is effective for detecting healthy plants and pods of cocoa from damaged ones only using mobile phone images. Focusing on a single land is not enough to combat climate change, which has different causes and involves also knowledge at a higher scale. We propose a new method of forecasting for the analysis of remote sensors. Remote sensor data come from GRACE NASA Mission and ERA5 produced by the Copernicus Climate Change Service at ECMWF. We implement a new deep neural network architecture named CIWA-net. It is based on a Fully Convolutional Neural Network (FCN) [ 1] and it is a U-net like architecture [2]. The aim of CIWA-net is to forecast Total Water Storage Anomalies (TWSA). We show the quality of our model with a comparison to a vanilla Convolutional Neural Network. CIWA-net could be used also for the detection of lands that interfere with agricultural work and yields, such as deserted areas, water-soaking soil areas, zones at risk of desertification, and poor land use. The employment of AI at the service of agriculture can decrease crop losses and waste, lower the inputs onto the soil of fertilizers, responsible for the increase of Greenhouse Gases. It could be useful to help the small farmers (at a local scale) and also the policy-makers and farmers’ cooperatives (at the regional scale) to take valid and coordinated countermeasures to improve the correct use of the lands, helping to contrast and adapt to climate change.

In an era dominated by rapid digitalization of sensed data, the secure exchange of sensitive information poses a critical challenge across various sectors. Established techniques, particularly in emerging technologies like the Internet of Things (IoT), grapple with inherent risks in ensuring the confidentiality and integrity of transmitted data. Blockchain technology, known for its decentralized and tamper-resistant characteristics, stands as a reliable solution for secure data exchange. However, the persistent challenge lies in protecting sensitive information amidst evolving digital landscapes. This paper explores the potential of Non-Fungible Tokens (NFTs), a manifestation of blockchain technology, as dynamic carriers for diverse forms of sensitive information among businesses beyond their conventional association with art and collectibles. Our solution leverages the immutable NFT data to serve as a secure data pointer, while the mutable NFT data holds sensitive information protected by steganography. This dual approach ensures both data integrity and authorized access, even in the face of evolving digital threats. A performance analysis validates the efficacy of the approach, highlighting its reliability, robustness, and resistance to potential attacks on hidden information, ensuring secure data transmission across industries.

Multiple entities use unmanned underwater drones for various functions, but how can they navigate underwater at such depths without a pilot? It is essential to understand how different unmanned underwater drones, such as remotely operated and autonomous underwater vehicles, function with underwater sensing technology. As each unmanned underwater drone has its function, the combination or chief use of the sensors is equally essential to recognize. Different underwater drone designs can be more cost-effective when a human is not on board as it can lead to a smaller, streamlined design in which oxygen and pressure control need not be a factor. Without considering oxygen limitations, these underwater drones can remain submerged for extended periods. These underwater vehicles operate autonomously or in conditions that may leave the individuals controlling the trajectory relying upon these sensors. It is also necessary to review how these sensors work, how they are implemented, and how they can help the public. This review was performed to address these research questions and provide an overview of sensors employed by unmanned underwater vehicles.

The article presents the results of evaluating the possibility of conducting radio astronomy studies in the windows of atmospheric transparency ~100, ~230 and ~350 GHz using the optical Big Telescope Alt-Azimuthal (BTA) of the SAO RAS. A list of some promising astronomical tasks is proposed. The astroclimat conditions at the BTA site and possible optical, cryogenic and mechanical interfaces for mounting a superconducting radio receiver at the focus of the optical telescope are considered. As a receiving system, arrays of detectors cooled to ~0.3 K based on the Superconductor – Insulator – Normal metal – Insulator – Superconductor (SINIS) structure are proposed. The implementation of the project will make it possible to use the BTA site of the SAO RAS not only to solve some astronomical problems (it is possible to consider the implementation of a single observatory, the VLBI mode in the Suffa, EHT and Millimetron projects), but will also be used to test various cryogenic detectors in a real observatory.

Contaminants of Emerging Concern (CECs), a new category of contaminants in limelight, is a major issue of global concern. The pervasive nature of CECs and its harmful effects, such as cancer, reproductive disorders, neurotoxicity etc., make the situation alarming. The perilous nature of CECs lies in the fact that even very small concentration of CECs can cause great impacts on living beings. It also has a nature of bioaccumulation. Thus, it is the ultimate need to have efficient sensors for detection of CECs to ensure safe living environment. Electrochemical sensors are an efficient platform for CEC detection as they are highly selective, sensitive, stable, reproducible, and prompt, and can detect very low concentrations of analyte. Major classes of CECs are pharmaceuticals, illicit drugs, personal care products, endocrine disruptors, newly registered pesticides, and disinfection by-products. This review focusses on CECs, including their sources and pathways, health effects caused by them, and electrochemical sensors as reported in literatures under each category for the detection of major CECs.

Viral infections can endanger public health by causing serious illness, leading to pandemics and burdening healthcare systems. Moreover, in the situation of a global spread, disruptions occur in every aspect of life including business, education, and social life. Fast and accurate diagnosis of viral infections has huge implications for saving people’s lives, preventing spread of the diseases, and minimizing social and economic damages. In the last decades, polymerase chain reaction (PCR) based techniques have been frequently used to detect viruses in the clinic. However, in a situation where rapid virus detection is the primary measure in preventing the spread, as in the case of ongoing COVID-19 pandemic, disadvantages of PCR, such as long processing times and requirement of sophisticated laboratory instruments, have been faced. Due to the urgent need for accurate techniques for virus detection, biosensor systems involved in many applications in biological detection are being developed for rapid, real-time, and high-throughput detection of viruses. Among various sensing platforms, optical devices are of great interest due to their advantages such as high sensitivity and direct readout. In the current review, usability of sensing techniques depending on optical phenomena, such as fluorescence-based sensors, surface plasmon resonance (SPR), surface enhanced Raman scattering (SERS), optical resonators and interferometry-based platforms, is discussed for virus diagnostics applications. Then, we focus on an interferometric biosensor developed by our group, single-particle interferometric reflectance imaging sensor (SP-IRIS), which has the capability to visualize single nanoparticles, to demonstrate its application for digital virus detection.

A novel electrophoretic technique to improve the sensing capabilities of charged particles in solution is presented. The proposed technique may improve the ability of metasurfaces to sense charged particles in solution by forcing them to preferentially sediment within metasurface regions of greatest sensitivity. Such a technique may be useful in various sensing applications, such as in biological, polymer, or environmental sciences, where low concentration particles in solution are of interest. The electrophoretic technique was simulated and experimentally tested using latex nanoparticles in solution. The results suggest that, using this technique, one may theoretically increase the particle density within the metasurface regions of greatest sensitivity by nearly 1900% in comparison to random sedimentation due to evaporation. Such an increase in particle density within the regions of greatest sensitivity may facilitate more precise material property measurements and enhance identification and detection capabilities of metasurfaces to low concentration particles in solution. It was experimentally verified that the electrophoretic technique enabled the preferential gathering of latex nanoparticles within the most sensitive metasurface regions, resulting in 900% - 1700% enhancements in metasurface sensing capabilities.

This contribution shows the possibilities of a low-cost multipurpose data logger that was built around an Arduino Mega 2560 single board computer. To transform the Arduino Mega into such a data logger, a sensor shield was designed that contains an SD-card, real-time clock, and different kinds of connectors so that sensors can easily be attached to the device. The software considers a wide range of predefined sensors from which a user can choose. To assess the performance of such a device, short-term monitoring campaigns in relation to outdoor air quality, human activity in an office, motion of a journey on a bike, and exhaust gas monitoring of a diesel generator were realized. Besides the possibilities to apply the data logger in different kinds of applications, a method is proposed to assess the credibility of such a system. The assessment based on the various short-term campaigns showed that the system scores positively on most of the performance indicators, but that unexpected (black swan) events affect the assessment over the longer term. This makes the development of low-cost scientific instruments harder than expected. The stability and long-term performance of this type of design requires continuous evaluation and engineering correction.

The lab-on-a-chip concept, enabled by microfluidic technology, promises the integration of multi-ple discrete laboratory techniques into a miniaturised system. Research into microfluidics has generally focused on the development of individual elements of the total system (often with rela-tively limited functionality), without full consideration for integration into a complete fully opti-mised and miniaturised system. Typically, the operation of many of the reported lab-on-a-chip devices is dependent on the support of a laboratory framework. In this paper, a demonstrator platform for routine laboratory analysis is designed and built, which fully integrates a number of technologies into a single device with multiple domains such as fluidics, electronics, pneumatics, hydraulics, and photonics. This facilitates the delivery of breakthroughs in research, by incorpo-rating all physical requirements into a single device. To highlight this proposed approach, this demonstrator microsystem acts as a fully integrated biochemical assay reaction system. The re-sulting design determines enzyme kinetics in an automated process and combines reservoirs, three-dimensional fluidic channels, optical sensing, and electronics in a low-cost, low-power and portable package.

The study of the human microbiome is a multidisciplinary area that affects from the field of technology to that of personalized medicine. The possibility of using microbiota biomarkers for the improvement in the diagnosis and monitoring of diseases (e.g. cancer), health conditions (e.g. obesity) or clinical parameters (e.g. ageing) has aroused great expectations, also in the scope of bio-electroanalytical chemistry. The well-known advantages of electrochemical transduction: high sensitivity, rapid response and possibility of miniaturization, together with the potential of new nanomaterials to improve both the design of electrode platforms and the performance of the resulting electrochemical biosensors make presumably a huge development in the next few years providing a better understanding of human microbiome entities. In this review article, the recent applications of electrochemical (bio)sensors for monitoring microbial metabolites and biomarkers of diseases related to different types of the human microbiome, with a special focus on the gastrointestinal microbiome, are reviewed. Examples of electrochemical devices applied to real samples are critically discussed as well as the challenges and prospects to be faced.

Low-cost monitors make it possible now for the first time to collect long-term (months to years) measurements of potential indoor exposure to fine particles. Indoor exposure is due to two sources: particles infiltrating from outdoors and those generated by indoor activities. Calculating the relative contribution of each source requires identifying an infiltration factor. We develop a method of identifying periods when the infiltration factor is not constant, and searching for periods when it is relatively constant. From an initial regression of indoor on outdoor particle concentrations, a Forbidden Zone can be defined with an upper boundary below which no observations should appear. If many observations appear in the Forbidden Zone, they falsify the assumption of a single constant infiltration factor. This is a useful quality assurance feature, since investigators may then search for subsets of the data in which few observations appear in the Forbidden Zone. The usefulness of this approach is illustrated using examples drawn from the PurpleAir network of optical particle monitors. An improved algorithm is applied with reduced bias, improved precision, and a lower limit of detection than either of the two proprietary algorithms offered by the manufacturer of the sensors used in PurpleAir monitors.

This study analyzes the efficacy of trapezius muscle electromyography (EMG) in discerning mental states, namely stress and meditation. Fifteen healthy participants were monitored to assess their physiological responses to mental stressors and meditation. Sensors were affixed to both the right and left trapezius muscles to capture EMG signals, while simultaneous electroencephalography (EEG) was conducted to validate cognitive states. Our analysis of various EMG features, considering frequency ranges and sensor positioning, revealed significant changes in trapezius muscle activity during stress and meditation. Notably, low-frequency EMG features facilitated enhanced stress detection. For accurate stress identification, sensor configurations can be limited to the right trapezius muscle. Furthermore, the introduction of a novel method for determining asymmetry in EMG features suggests that applying sensors on bilateral trapezius muscles can improve the detection of mental states. This research presents a promising avenue for efficient cognitive state monitoring through compact and convenient sensing.

Magnetoelectric (ME) sensor is a new type magnetic sensor with ultrahigh sensitivity, low power consumption, and suitable for the measurement of low frequency weak magnetic field. In this study, metglas/PZT-5B ME sensor with a mechanical resonance frequency f_res of 60.041 kHz was prepared. It is interesting to note that its magnetic field resolution reaches 0.20 nT at f_res and 0.34 nT for DC field, respectively. In order to measure the ultralow frequency AC magnetic fields, a frequency upconversion technique was employed. Under this technique, a limit of detection (LOD) of AC magnetic field lower than 1 nT at 8 Hz is obtained, and the minimum LOD of 0.51 nT is achieved at 20 Hz. The high resolution ME sensor with sub-pT level is promising in the field of low frequency weak magnetic field measurement technology.

In this paper, we propose a reconfigurable intelligent surface (RIS) that can dynamically switch the transmission and reflection phase of incident electromagnetic waves in real time to realize the dual-beam or quad-beam and convert polarization of the transmitted beam. Such surfaces can redirect a wireless signal at will to establish robust connectivity when the designated line-of-sight channel is disturbed, thereby enhancing the performance of wireless communication systems by creating an intelligent radio environment. When integrated with a sensing element, they are integral to performing joint detection and communication functions in future wireless sensor networks. In this work, we first analyze the scattering performance of a reconfigurable unit element and then design a RIS. The dynamic field scattering manipulation capability of the RIS is validated by full-wave electromagnetic simulations to realize six different functions. The scattering characteristics of the proposed unit element, which incorporates two p-i-n diodes, have been substantiated through practical implementation. This involved the construction of a simple prototype and the subsequent examination of its scattering properties via the free-space measurement method. The obtained transmission and reflection coefficients from the measurements are in agreement with the anticipated outcomes from simulations.

For technical or medical applications, the knowledge of the exact kinematics of the human hand is key to utilizing its capability to handle and manipulate objects and to communicate with other humans or machines. The optimal relationship between the number of measurement parameters, measurement accuracy as well as complexity, usability and cost of the measuring systems is hard to find. Biomechanic assumptions, the concepts of a biomechatronic system and the mechatronic design process as well as commercially available components are used to develop a sensorized glove. The proposed wearable can measure 14 of 15 angular values of a simplified hand model introduced in this paper. Additionally, five contact pressure values at the fingertips and inertial data of the whole hand with a degree of freedom of six are gathered. Due to the modular design and a hand size examination based on anthropometric parameters, the concept of the wearable is applicable for a large variety of hand sizes and adaptable to different use cases. Validations show a combined root-mean-square error of 0.99° to 2.38° for the measurement of all joint angles at one finger, surpassing the human perception threshold and the current state of the art in science and technology for comparable systems.

We report on the use of quartz-enhanced photoacoustic spectroscopy (QEPAS) for multi-gas detection. Photo-acoustic (PA) spectra of mixtures of water (H2O), ammonia (NH3) and methane (CH4) were measured in the mid-infrared (MIR) wavelength range using a MIR (mid-infrared) optical parametric oscillator (OPO) light source. Highly overlapping absorption spectra is a common challenge for gas spectroscopy. To mitigate this, we use a partial least-squares regression (PLS) method to estimate the mixing ratio and concentrations of the individual gasses. The concentration range explored in the analysis varies from a few parts-per-million (ppm) to thousands of ppm. Spectra obtained from HITRAN and experimental single-molecule reference spectra of each of the molecular species were acquired and used as training data sets. These spectra were used to generate simulated spectra of the gas mixtures (linear combinations of the reference spectra). Here in this proof-of-concept experiment we demonstrate that after an absolute calibration of the QEPAS cell, the PLS analyses could be used to determine concentrations of single molecular species with a relative accuracy within a few % for mixtures of H2O, NH3 and CH4 and with an absolute sensitivity of approximately 300(±50) ppm/V, 50(±5) ppm/V and 5(±2) ppm/V for water, ammonia and methane, respectively. Thus, demonstrating that QEPAS assisted by PLS is a powerful approach to estimate concentrations of individual gas components with considerable spectral overlap, which is a typical scenario for real-life adoptions and applications.

The fourth industrial revolution, also known as Industry 4.0, has led to an increased transition towards automation and reliance on data-driven innovations and strategies. Companies in the manufacturing sector are heavily integrating Industry 4.0 technologies, including cloud compu-ting, cyber-physical systems (CPS), big data analytics, horizontal and vertical system integration, the internet of things (IoT), and additive manufacturing (3d printing). The interconnected systems and processes have significantly increased operational efficiency, enhanced organizational capacity to monitor and control functions, reduced costs, and improved product quality. One significant way that companies have achieved these benefits is by integrating diverse sensor technologies within these innovations, allowing critical data collection on products, equipment performance, and maintenance. The sensors connect systems and machines, allowing them to communicate and track operations for enhanced operations. While numerous research has been conducted to show the role of sensors in industry 4.0, limited studies show how these innovations can leverage product design to maximize benefits and opportunities. Given the rapidly changing market conditions, Industry 4.0 requires new products and business models to ensure companies adjust to the current and future changes. These requirements call for the evolutions in product design processes to accommodate design features and principles applicable in the current dynamic business environment. This research paper employs a systematic bibliometric literature review (LRSB) methodology to explore and synthesize data on how Industry 4.0 and sensors can leverage product design. The results show that various product design features create opportunities to be leveraged to guarantee the success of Industry 4.0 and sensor technologies. However, the research also identifies numerous challenges that undermine the ongoing transition towards intelligent factories and products.

Reliable and accurate flood prediction is a challenging task in poorly gauged basins due to data scarcity. Data is an essential component of any AI/ML model today, and the performance of such models hugely depends on the availability of sufficient amount of trusted, representative data. However, unlike a few well-studied rivers, most of the rivers in developing countries are still insufficiently monitored, which significantly hinges the design and development of advanced flood prediction models and early warning systems. This paper presents a multi-modal, sensor-based and near-real time river monitoring system to produce a multi-feature data set for the Kikuletwa river in Northern Tanzania, an area that heavily suffers from frequent floods. Our deployed system, which gather information about river depth levels and weather at several locations, aims at widening the ground truth of the river characteristics and eventually improve the accuracy of flood predictions. We provide details on the monitoring system used to gather the data as well as report on the methodology and the nature of the data. Finally, we present the relevance of the data set in the context of flood prediction, discussing the most suitable AI/ML-based forecasting approaches, while also highlighting some applications of the data set beyond flood warning systems.

Pseudo-nitzschia spp. blooms are a recurrent problem in many coastal areas globally imposing some significant threats to the health of human, ecosystems and economy. Monitoring programmes have been established, where feasible, to mitigate the impacts caused by Pseudo-nitzschia spp. and other harmful algae blooms. The detection of such blooms from satellite data could really provide timely information on emerging risks but the development of taxa-specific algorithms from available multispectral data is still challenged by coupled optical properties with other taxa and water constituents, availability of ground data and generalisation capabilities of algorithms. Here, we developed a new set of algorithms (PNOI) for the detection and monitoring of Pseudo-nitzschia spp. blooms over the Galician coast (NW Iberian Peninsula) from Sentinel-3 OLCI reflectances using support vector machine (SVM). Our algorithm was trained and tested with reflectance data from 260 OLCI images and 4607 Pseudo-nitzschia spp. match up data points, of which 2171 were of high quality. The performance of no bloom/bloom model in the independent test set was robust, showing values of 0.80, 0.72 and 0.79 for area under the curve (AUC), sensitivity and specificity, respectively. Similar results were obtained by our below detection limit/presence model. We also present different model thresholds based on optimisation of true skill statistic (TSS) and F1-score. PNOI outperforms linear models, while its relationship with in-situ chlorophyll-a concentrations is weak demonstrating poor correlation with the phytoplankton abundance. We showcase the importance of PNOI algorithm and OLCI sensor for monitoring the bloom evolution between the weekly ground sampling and during periods of ground data absence, such as due to Covid-19.

The integration of Artificial Intelligence (AI) with Digital Twins (DTs) has emerged as a promising approach to revolutionize healthcare, particularly in the diagnosis and management of thoracic disorders. This study proposes a comprehensive framework, named Lung-DT, which leverages IoT sensors and AI algorithms to establish a digital representation of a patient’s respiratory health. Using the YOLOv8 neural network, the Lung-DT system accurately classifies chest X-Rays into five distinct categories of lung diseases, including "Normal," "Covid," "Lung Opacity," "Pneumonia," and "Tuberculosis". The system’s performance was evaluated on a chest X-Ray dataset, demonstrating an impressive average accuracy of 96.6% across all classes. Further tests (prediction) were conducted on the trained network using a third dataset available in the literature and completely unknown to the network, yielding an average accuracy of 98% across three classes. The proposed Lung-DT framework offers several advantages over conventional diagnostic methods. Firstly, it enables real-time monitoring of lung health through continuous data acquisition from IoT sensors, facilitating early diagnosis and intervention. Secondly, the AI-powered classification module provides automated and objective assessments of chest X-Rays, reducing dependence on subjective human interpretation. Thirdly, the twin digital representation of the patient’s respiratory health allows for comprehensive analysis and correlation of multiple data streams, providing valuable insights for personalized treatment plans. The integration of IoT sensors, AI algorithms, and DT technology within the Lung-DT system demonstrates a significant step towards improving thoracic healthcare. By enabling continuous monitoring, automated diagnosis, and comprehensive data analysis, the Lung-DT framework has enormous potential to enhance patient outcomes, reduce healthcare costs, and optimize resource allocation.

Organ-on-a-chip (OOC) is an emerging technology that simulates an artificial organ within a microfluidic cell culture chip. Current cell biology research focuses on in vitro cell culture due to various limitations of in vivo testing. Unfortunately, in vitro cell culture fails to provide an accurate microenvironment, and in vivo cell culture is expensive and has historically been a source of ethical controversy. OOC aims to overcome these shortcomings and provide the best of both in vivo and in vitro cell culture research. The key component of the OOC design is utilizing microfluidics to ensure a stable concentration gradient, dynamic mechanical stress modeling, and accurate reconstruction of a cellular microenvironment. OOC also has the advantage of complete observation and control of the system, which is impossible to recreate in in vivo research. Multiple throughputs, channels, membranes, and chambers are constructed in a polydimethylsiloxane (PDMS) array to simulate various organs on a chip. Various experiments can be performed utilizing OOC technology, including drug delivery research and toxicology. Current technological expansions involve multiple organ microenvironments on a single chip, allowing for studying inter-tissue interactions. Other developments in the OOC technology include finding a more suitable material as a replacement for PDMS and minimizing artefactual error and non-translatable differences.

Palpation is a simple but effective method to differentiate tumors from healthy tissues. Development of miniaturized tactile sensors embedded on endoscopic or robotic devices are the key toward precise palpation diagnosis and the subsequent timely treatment. This paper reports on the fabrication and characterization of a novel tactile sensor with mechanical flexibility and optical transparency that can be easily mounted on soft surgical endoscopes and robotics. Utilizing the pneumatic sensing mechanism, the sensor offers a high sensitivity of 1.25 mbar and negligible hysteresis, enabling the detection of phantom tissues with different stiffnesses ranging from 0 to 2.5 MPa. Our configuration combining pneumatic sensing and hydraulic actuating also eliminates electrical wiring from the functional elements located at the robot end-effector, thereby enhancing the system safety. The optical transparency path in the sensors together with its mechanical sensing capability open interesting possibility in early detection of solid tumor as well as in the development of all in-one soft surgical robots that can perform visual/mechanical feedback and optical therapy.

Three-dimensional (3D) printing technology, also known as additive manufacturing (AM), has emerged as an attractive state-of-the-art tool for precisely fabricating functional materials with complex geometries, championing several advancements in tissue engineering, regenerative medicine, and therapeutics. However, this technology has an untapped potential for biotechnological applications, such as sensor and biosensor development. By exploring these avenues, the scope of 3D printing technology can be expanded and pave the way for groundbreaking innovations in the biotechnology field. Indeed, new printing materials and printers would offer new possibilities for seamlessly incorporating biological functionalities within the growing 3D scaffolds. Herein, we review the extrusion-based 3D printing modalities emphasizing biosensor applications. We highlighted the application of natural, synthetic, and composite biomaterials as 3D-printed soft hydrogels. Emphasis was placed on the approach by which the sensing molecules were introduced during the fabrication process. Finally, the future perspective was provided.

Autonomous driving vehicles rely on sensors for the robust perception of surroundings. Such vehicles are equipped with multiple perceptive sensors with a high level of redundancy to ensure safety and reliability in any driving condition. However, multi-sensor, such as camera, LiDAR and radar, systems bring up the requirements related to sensor calibration and synchronization, which are the fundamental blocks of any autonomous system. On the other hand, sensor fusion and integration have become important aspects of autonomous driving research and directly determine the efficiency and accuracy of advanced functions such as object detection and path planning. Classical model-based estimation and data-driven models are two mainstream approaches to achieving such integration. Most recent research is shifting to the latter, showing high robustness in real-world applications but requiring large quantities of data to be collected, synchronized, and properly categorized. To generalize the implementation of the multi-sensor perceptive system, we introduce an end-to-end generic sensor dataset collection framework that includes both hardware deploying solutions and sensor fusion algorithms. The framework prototype integrates a diverse set of sensors, such as cameras, LiDAR, and radar. Furthermore, we present a universal toolbox to calibrate and synchronize three types of sensors based on their characteristics. The framework also includes the fusion algorithms, which utilize the merits of three sensors , namely, camera, LiDAR and radar, and fuse their sensory information in a manner that is helpful for object detection and tracking research. The generality of this framework makes it applicable in any robotic or autonomous applications, also suitable for quick and large-scale practical deployment.

Recently, cobalt iron boron (CoFeB) thin films have been widely investigated to apply to magnetic sensors, due to their high magnetic moment, anisotropy, and stability. However, most of these studies are conducted on rigid silicon substrates. For more diverse applications of magnetic sensors and angle sensors, it is important to explore the properties of ferromagnetic thin films grown on non-rigid deformable substrates. Here, using representative deformable substrates such as polyimide (PI), polyethylene naphthalate (PEN) and polydimethylsiloxane (PDMS) that can be bent or stretched, we report experimental comparison of in-plane magnetic field angle-dependent properties of the amorphous Ta/CoFeB/MgO/Ta thin film which is grown on those deformable substrates. We investigate effects of substrate roughness, tensile stress, characteristics of deformable substrates, and sputtering process on the change of magnetic properties like coercive field (Hc), remanence over saturation magnetization (Mr/Ms), and their biaxial characteristics. This work presents unconventional foundations for exploring deformable magnetic sensors capable of detecting magnetic field angle.

The condition of surface transportation infrastructure directly affects the economic health of a nation. However, it is difficult to justify the large sums of money needed to extend current methods to monitor all the multimodal infrastructure. The convergence of connected vehicle and cloud computing technologies presents an opportunity to automate the collection of ride quality and imagery data to continuously assess the condition of all roadways and railways. This paper presents several perspectives to help policy and standardization initiatives promote adoption.

Osteoarthritis (OA) poses a growing challenge for the aging population, especially in hip and knee joints, contributing significantly to disability and societal costs. Conventional clinical evaluations, typically performed in controlled settings, face difficulties in capturing the dynamic characteristics of rehabilitation and functioning in real-life scenarios. The study assessed the use of automated unsupervised evaluations in the rehabilitation process for patients after hip and knee replacements. We analyzed data from 1144 individuals who used a digital application after surgery, activity data were collected using the Garmin Vivofit 4. Several parameters such as the Peak 6-Minute Consecutive Cadence (P6MC) and Peak 1-Minute Cadence (P1M) were computed and analyzed on a daily basis. The results indicated that cadence measurements, specifically, can effectively differ among individuals with hip and knee conditions as well as the recovery process. Moreover, these metrics demonstrated a high level of responsiveness in monitoring the progress of recovery, surpassing the effectiveness of simply measuring the total number of steps taken. The study highlighted the capacity of technology-driven, patient-centered rehabilitation to improve accuracy, tailor therapy to individual patients, and increased patient involvement. This research also highlighted the significance of automated, unsupervised assessments in enhancing rehabilitation results for OA patients following hip and knee replacement, as tele-rehabilitation becomes increasingly important.

Nanotechnology and polymer engineering are steering towards a new development to invade deleterious mysteries. In the last few decades, polymer engineering has grabbed researchers’ attention and similarly, polymeric network-engineered structures have been vastly studied. Prior to therapeutic application, early and quick detection analyses are critical. Therefore, developing nanoscale sensors to manage the acute expression of feeble states and malignancies to draw therapeutic lines demands advanced nanoengineering. In spite of nano-therapeutics have emerged as an alternative approach to tackling strenuous diseases. Also, studies have shown highly biocompatible biomedical engineering has emerged with sheer progression. Moreover, hydrogels have emerged as a three-dimensional (3D) polymeric network that consists of hydrophilic natural or synthetic polymers. The resemblance of hydrogels with tissue structure makes it more unique to study inquisitively. Preceding studies have shown a vast spectrum of synthetic and natural polymer deployment in the field of biotechnology and molecular diagnostics. This review explores recent studies on synthetic and natural polymer engineered hydrogel-based biosensors and their applications in multipurpose diagnostics and therapeutics. We reviewed the latest studies on hydrogel-engineered biosensors, exclusively DNA-based and DNA hydrogels fabricated biosensors.

A partial aperture onboard calibration method can solve the onboard calibration problems of some large aperture remote sensors, which is of great significance for the development trend of increasingly large apertures in optical remote sensors. In this paper, the solar diffuser reflectance degradation monitor (SDRDM) in the onboard calibration assembly (CA) of the FengYun-4 (FY-4) advanced geostationary radiance imager (AGRI) is used as the reference radiometer for measuring the partial aperture factor (PAF) for the AGRI onboard calibration. First, the linear response count variation relationship between the two is established under the same radiance source input. Then, according to the known bidirectional reflection distribution function (BRDF) of the solar diffuser (SD) in the CA, the relative reflectance ratio coefficient between the AGRI observation direction and the SDRDM observation direction is calculated. On this basis, the response count value of the AGRI and the SDRDM is used to realize the high-precision measurement of the PAF of the AGRI B1 ~ B3 bands by simulating the AGRI onboard calibration measurement under the illumination of a solar simulator in the laboratory. According to the determination process of the relevant parameters of the PAF, the measurement uncertainty of the PAF is analyzed; this uncertainty is better than 2.04% and provides an important reference for the evaluation of the onboard absolute radiometric calibration uncertainty after launch.

The rapid growth of the global wearable technologies market is projected to reach $61.30 billion by 2030 which reflects a shift towards personalised health monitoring embedded in everyday activities. This paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. Experimental results demonstrate the sensor’s capability to detect water droplets and glucose concentrations, showcasing promising applications for health monitoring. The embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

In this study on volume determination in waste sorting facilities, we evaluate the effectiveness of ultrasonic sensors and address waste-material-specific challenges. Although ultrasonic sensors offer a cost-effective automation solution, their accuracy is affected by irregular waste shapes, varied compositions, and environmental factors. Notable inconsistencies in volume measurements between storage bunkers and conveyor belts underscore the need for a comprehensive approach to standardize bale production. With prediction reliability being constrained by limited data sets, undocumented modifications to machine-settings and sensor failures, this task renders a challenging application area for Machine Learning. We explore related research and present dataset analyses from three distinct waste sorting facilities in Europe, addressing issues as sensor usability, data quality and material specifics. Our analysis suggests promising strategies and future directions for enhancing waste volume measurement accuracy, ultimately aiming to advance sustainable waste management.

Objective To measure, exposure to PM2.5 particles in outdoor smoking areas and changes in breathing rates in patients with asthma or chronic obstructive pulmonary disease (COPD). Setting Sixty venues in Czechia, Ireland and Spain, in an open, non-randomised, clinical trial. Participants We studied 60 patients-30 asthma patients (Female 63.3%), with a mean age (+/-standard deviation [SD]) of 47.4 (19.0 SD), and 30 COPD patients (Female 51.6%), mean age 63.5 (10.1 SD), smokers, non-smokers or ex-smokers, recruited through medical clinics. Intervention Patients wore a PM2.5 particle monitor (AirSpeck), and a breath monitor (RESpeck) for 24 hours to determine changes in breathing rates (Br) at rest and during a visit to an outside smoking area. Spirometry and breath CO were measured before and the day after visiting an outdoor smoking area. Results PM2.5 levels in the 60 venues were highly variable, in 1 premises levels of PM2.5 were sustained for at least 15 minutes at ≥ 2,000 µg/m3, in 4 premises, ≥ 500 (range 1,933-539) µg/m3, in 8 premises, ≥ 200(range 480-203) µg/m3, in 9 premises, ≥ 100 (range 170-108) µg/m3, in 8 premises, ≥ 40 (range 80.5- 40.1) µg/m3, in 9 premises, ≥ 25 µg/m3, in 10 premises, ≥ 10 µg/m3, in 8 premises, and ≤10 µg/m3 in only 3 premises, with a single wall. The overall breathing rates/minute (Br)did not change significantly but in 28 patients mean Br increased from 21.47 (1.74 SD) to 22.8 (2.29 SD), change of -1.35 (-1.80-0.91 C.I), p value 0.00 and mean in 29 patients Br decreased from 21.95(2.43 SD) to 20.38(2.79 SD), 1.57(1.03-2.12 C.I), p value 0.00. Conclusion Exposure to high levels of PM2.5, and associated alteration of patients’ breathing rates occurred in outdoor smoking areas despite national comprehensive smokefree laws. These exposure levels support the abolition of such areas. (Words 295) ClinicalTrials.gov ID: NCT03074734 Ethics: Approval Number: Ref: 15-103

Plants have acquired sets of highly regulated and complex signaling pathways to respond to unfavorable environmental conditions during evolution. Calcium signaling, as a vital mechanism, enables plants to respond to external stimuli, including abiotic and biotic stresses, and coordinate the basic processes of the growth and development. In the present study, the calcium sensor families, including CBL and CIPK, were investigated in the halophyte plant, Aeluropus littoralis, with a comprehensive analysis. Here, six AlCBL genes, and twenty AlCIPK genes were presented. The analysis of the gene structure and conserved motifs, as well as physicochemical properties, showed that these genes are highly conserved during evolution. The expression levels of AlCBL genes and AlCIPK genes were evaluated under salt stress in leaf and root tissue. Based on the real-time RT-PCR results, AlCIPK gene family had a higher variation in mRNA abundance compared to the AlCBL gene family. The AlCIPKs were found to have a higher abundance in leaves than in roots. The results suggest that the interaction pattern of AlCBL genes with AlCIPK is tissue-specific, and different interactions can be expected in leaves and roots. Based on these patterns AlCIPK3.1 - AlCBL4.1 and AlCIPK1.2 - AlCBL4.4 can interact in root tissue, while the AlCBL10 has the potential to interact with the AlCIPK5, AlCIPK26 and AlCIPK12.3 in the leaf tissue. These findings provide valuable information on the structure and function of calcium sensor families in Aeluropus littoralis a halophyte plant, for future research on the biological function of CBLs and CIPKs on salt stress resistance.

In recent years, the integration of sensors in agriculture has emerged as a pivotal catalyst for transforming conventional farming practices into precision agriculture. Sensor application is impacting the everyday objects that enhance human life. In this special issue, the main objective was to address recent advantages of sensor application in agriculture covering a wide range of topics in this field. This provides overview of diverse application of sensors in agriculture, highlighting their role in enhancing productivity, sustainability, and resource management. sensors are instrumental in monitoring various agriculture parameter such as soil condition, weather, crop health and livestock wellbeing. By collecting real-time data and providing valuable insight, sensors enable precision farming, optimize resource allocation, and minimize environmental impacts. we have to explore the key sensor types used in agriculture, their applications, benefits, and future prospects, emphasizing their crucial roles in the modernization of agriculture and global quest for food security and crop production.

Screening and early diagnosis of diseases are crucial for a patient's treatment to be successful and to improve their survival rate, especially in cancer. The development of non-invasive analytical methods able to detect biomarkers of pathologies is a critical point to define a successful treat-ment and a good outcome. This study extensively reviews electrochemical methods used for the development of biosensors in liquid biopsy, owing to their ability to provide rapid response, pre-cise detection, and low detection limits. We also discuss new developments in electrochemical biosensors, which can improve the specificity and sensitivity of standard analytical procedures. Electrochemical biosensors demonstrate remarkable sensitivity in detecting minute quantities of analytes, encompassing proteins, nucleic acids, and circulating tumor cells, even within challeng-ing matrices such as urine, serum, blood, and various other body fluids. Among the various de-tection techniques used for the detection of cancer biomarkers, even in the picogram range, volt-ammetric sensors are deeply discussed in this review because of their advantages and technical characteristics. This widespread utilization stems from their ability to facilitate quantitative de-tection of ions and molecules with exceptional precision. The comparison of each electrochemical technique is discussed to provide the selection of appropriate analytical methods.

The remote monitoring of clinical parameters plays a fundamental role in different situations, like pandemic health emergencies and post-surgery conditions. In these situations, the patients might be impeded in their movements and it could be difficult to have a specific health monitoring. In recent years, technological advancements in smartphones have opened up new possibilities in this landscape. The present work aims to propose a new method for respiratory kinematics monitoring via smartphone sensors. In particular, a specific application was developed to register Inertial Movement Unit (IMU) sensors data from the smartphone for respiratory kinematics measurement and to guide the user through a specific acquisition session. The session was defined to allow for the monitoring of the respiratory movement in five prescribed positions. The application and the sequence were successfully tested on a given population of 77 healthy volunteers. The resulting accelerometers and gyroscope signals were processed to evaluate the significance of differences according to participants sex, vector components and smartphone positioning and, finally, to estimate the respiratory rate. The emerged statistical differences revealed the significance of information in the different acquisition positions.

Machine learning (ML) systems that use sensors obtain observations from sensors and use them to recognize and interpret the current situation. These systems are susceptible to sensor-based adversarial example attacks (AEs); if some sensors are vulnerable and can be compromised by an attacker, the attacker can change the output of the system by changing the values of the sensors. The detection of compromised sensors is important to defend the system against sensor-based AEs, because we can check the sensors and replace them by detecting the sensors used by the attacker. In this paper, we propose a method to detect the sensors used in sensor-based AEs by utilizing the features of the attack that cannot be avoided. In this method, we introduced a model called the feature-removable model (FRM), which allows us to select the features used as inputs into the model. Our method detects the sensors used in sensor-based AEs by finding the inconsistencies between the outputs of the FRM obtained by changing the selected features. We evaluated our method using a human activity recognition model with sensors attached to the user’s chest, wrist, and ankle. We demonstrate that our method can accurately detect sensors used by the attacker and achieves an average Recall of Detection of 0.92, and the average Precision of Detection is 0.72.

This study presents a research plan that utilizes data obtained from wearable devices to identify human activities and gain insights into human behavior. We developed a model capable of classifying activities similar to human behavior and evaluated the effectiveness and generalization capabilities of this model. The data underwent initial preprocessing, including standardization and normalization. Additionally, recognizing the inherent similarities between human activity behaviors, we introduced a multi-layer classifier model. The first layer is a random forest model based on stepwise regression, which may encounter reduced accuracy for similar activities. The second layer employs a Support Vector Machine (SVM) model based on Kernel Fisher Discriminant Analysis (KFDA). KFDA is used to reduce the dimensionality of data points with potential confusion, followed by SVM for classification. The model was experimentally evaluated and applied to four benchmark datasets: UCI DSA, UCI HAR, WISDM, and IM-WSHA. The experimental results demonstrate that our approach achieved recognition accuracies of 99.71%, 98.71%, 99.12%, and 97.6% on these datasets, indicating excellent recognition performance. Furthermore, to assess the model's generalization ability, we performed K-fold cross-validation on the random forest model and utilized ROC curves for the SVM classifier. The results indicate that our multi-layer classifier model exhibits robust generalization capabilities.

The aim of this study was to adapt a treadmill-developed method for determination of inner-cycle parameters in cross-country roller ski skating for a field application. The method is based on detecting initial and final ground-contact of poles and skis during cyclic movements. Eleven athletes skied four laps of 2.5 km at low and high endurance-intensity, using two types of skis with different rolling coefficients. Participants were equipped with inertial measurement units (IMUs) attached to their wrists and skis, while insoles with pressure sensors and poles with force measurements were used as reference systems. The method based on IMUs was able to detect more than 97% of the temporal events compared to the reference system. The inner-cycle temporal parameters had a precision ranging from 49 to 59 ms, corresponding to 3.9% to 13.7% of the corresponding inner-cycle duration. Overall, this study showed good reliability of using IMUs on athlete’s wrists and skis to determine temporal events, inner-cycle parameters and the performed sub-techniques in cross-country roller ski skating in field-conditions.

The utilization of Fiber Bragg Grating (FBG) sensors in innovative optical sensor networks has displayed remarkable potential in providing precise and dependable thermal measurements in hostile environments on Earth. Multi-Layer Insulation (MLI) blankets serve as critical components of spacecraft and are employed to regulate the temperature of sensitive components by reflecting or absorbing thermal radiation. To enable accurate and continuous monitoring of temperature along the length of the insulative barrier without compromising its flexibility and lightweight, FBG sensors can be embedded within the thermal blanket, thereby enabling distributed temperature sensing. This capability can aid in optimizing the thermal regulation of the spacecraft and ensuring the reliable and safe operation of vital components. Furthermore, FBG sensors offer several advantages over traditional temperature sensors, including high sensitivity, immunity to electromagnetic interference, and the ability to operate in harsh environments. These properties make FBG sensors an excellent option for thermal blankets in space applications, where precise temperature regulation is crucial for mission success. Nevertheless, the calibration of temperature sensors in vacuum conditions poses a significant challenge due to the lack of an appropriate calibration reference. Therefore, this paper aims to investigate innovative solutions for calibrating temperature sensors in vacuum conditions. The proposed solutions have the potential to enhance the accuracy and reliability of temperature measurements in space applications, which can enable engineers to develop more resilient and dependable spacecraft systems.

The main objective of this work is the design and implementation of self-adaptive capabilities in wireless sensors by applying control engineering and model-based design methodologies. It has been addressed the problem related to the changes in the flow of data packets through the network connection and the excess energy consumption that this causes in these devices. To design the solution, a systemic characterization of the scheduling and execution process of embedded tasks on the device has been carried out. This means defining cause-effect relationships in the system and its modelling theoretically and/or experimentally. In turn, these models facilitate the design of control strategies to improve the dynamic behavior of the system. As a solution, a self-adaptation strategy based on feedforward control algorithm has been designed and developed, which has been applied to improve the dynamic behavior and resource consumption. The developed solution has been satisfactorily evaluated experimentally.

Low-cost particulate matter (PM) sensors offer an excellent opportunity to improve our knowledge about this type of pollution. Their size and their cost, which support multi-node network deployment, along with their temporal resolution, enable them to report fine spatio-temporal resolution for a given area. These sensors have known issues across performance metrics. Generally, the literature focuses on the PM mass concentration reported by these sensors but some models of sensors also report particle number concentrations (PNC) segregated into different PM size bins. In this study, 8 units of each Alphasense OPC-R1, Plantower PMS5003 and Sensirion SPS30 have been exposed, under controlled conditions, to short-lived peaks of PM generated using two different combustion sources of PM, exposing the sensors to different particle size distributions to quantify and better understand the low cost sensors performance across a range of relevant environmental ranges. The PNC reported by the sensors were analysed. This study showed that there is added value in directly using the PNC reported by the sensors instead of the mass concentrations, which could aid the efforts to calibrate these sensors to a known accuracy. It demonstrated that all sensors tested here could track the fine temporal variation of PNC, that the Alphasense OPC-R1 could closely follow the variations of size distribution between the two sources of PM, and it showed that particle size distribution and composition are more impactful on the sensors measurement than relative humidity.

A critical aspect of coronary heart disease (CHD) care and secondary prevention is ensuring patients have access to evidence-based information. The purpose of this review is to summarise the guiding principles, content, context and timing of information and education that is beneficial for supporting people with CHD and potential communication strategies including digital interventions. We conducted a scoping review involving searching four databases (Web of Science, PubMed, CINAHL, Medline) for articles published from January 2000 to August 2022. Literature was identified through title and abstract screening by expert reviewers. Evidence was synthesised according to the review aims. Results demonstrated that information-sharing, decision-making, goal-setting, positivity and practicality are important aspects of secondary prevention and should be patient-centred and evidenced based with consideration of patient need and preference. Initiation and duration of education is highly variable between and within people, but hence communication and support should be regular and ongoing. In conclusion, text messaging programs, smartphone applications and wearable devices are examples of digital health strategies that facilitate education and support for patients with heart disease. There is no one size fits all approach that suits all patients at all stages and hence flexibility and a suite of resources and strategies is optimal.

Seafood, especially from the ocean, is now seen as a greener and more sustainable source of protein causing an increase in its demand. This has also led to people making choices towards seafood as a replacement of carbon intensive protein sources. As a result, the demand for seafood is growing, and the Aquaculture industry is required to increase their produce while keeping the produce safe and sustainable. There are many challenges faced by the aquaculture industry in meeting these increased demands. One such challenge is the presence of harmful algal blooms (HAB) in the ocean which can have a major impact on aquatic life. In this paper we look at the impact of this challenge on aquaculture and the mitigating strategies. We will focus on Abagold Limited, a land-based marine aquaculture business that specializes in large scale production of abalone (Haliotis midae) based in Hermanus, South Africa. HABs are considered a threat to commercial scale abalone farming along the South-African coastline and requires continuous monitoring. The most recent HAB was in February-April 2019, the area experienced a severe red-tide event with blooms of predominantly Lingulodinium polyedrum. We present some of the mitigation strategies employing digital technologies for future proofing the industry.

The healthy function of the vestibular system (VS) is of vital importance for individuals to carry out their daily activities independently and safely. This study carries out Tsallis entropy (TE)-based analysis on insole force sensor data in order to extract features to differentiate between healthy and VS-diseased individuals. Using a specifically developed algorithm, we detrend the acquired data to examine the fluctuation around the trend curve in order to consider the individual’s walking habit and thus increase the accuracy in diagnosis. It is observed that the TE-value increases for diseased people as an indicator of the problem of maintaining balance. As one of the main contributions of this study, in contrast to studies in the literature that focus on gait dynamics requiring extensive walking time, we directly process the instantaneous pressure values, enabling to reduce the data acquisition period significantly. The extracted feature set is then inputted into fundamental classification algorithms, with the Support-Vector-Machine (SVM) demonstrating the highest performance, achieving an average accuracy of 95%. This study constitutes a significant step of a large project aiming to identify specific VS disease together with its stage. The performance achieved in this study provides a strong motivation to further explore this topic.

Unmanned aerial vehicle (UAV) usage is increasing drastically worldwide as UAVs are used in various industries for many applications, such as inspection, logistics, agriculture, and many more. This is because performing a task using UAV makes the job more efficient and reduces the workload needed. However, for a UAV to be operated manually or autonomously, the UAV must be equipped with proper safety features. An anti-collision system is one of the most crucial and fundamental safety features that UAVs must be equipped with. The anti-collision system allows the UAV to maintain a safe distance from any obstacles. The anti-collision technologies are of crucial relevance to assure the survival and safety of UAVs. Anti-collision of UAVs can be varied in the aspect of the use of sensors and the system’s working principle. This article provides a comprehensive overview of anti-collision technologies for UAVs. It also presents drone safety laws and regulations that prevent a collision at the policy level. The process of anti-collision technologies is studied from three aspects: Obstacle detection, collision prediction, and collision avoidance. A detailed overview and comparison of the methods of each element and an analysis of their advantages and disadvantages have been provided. In addition, the future trends of UAV anti-collision technologies from the viewpoint of fast obstacle detection and wireless networking are presented.

Studies at the molecular, systemic, and epidemiological levels have shown that chronic metal exposure is linked to significant health consequences, including cancer, affecting hundreds of millions worldwide. Subtle and convoluted mechanisms underline metals' toxicity and carcinogenicity. The use of sensors for carcinogenic metals' trace detection is on the rise due to their selectivity, simplicity, and affordability. Biotechnology and microelectronics in the development of sensors have grown complementarily in recent years. This study offers a comprehensive overview of current research and advancements in developing sensors for detecting carcinogenic metals. Here, we have focussed on the developed biosensor platforms for group 1 carcinogens, i.e., arsenic, nickel, cadmium, chromium, and beryllium, along with their brief roles in human carcinogenesis. This review also looks at the importance of sensing such metal exposure in humans from a larger perspective, hoping to influence future research toward early prevention and treatment of illnesses like cancer.

This paper presents the development of a cheap and rapid electrochemical sensor for ascorbic acid detection. In particular, the graphite ink working electrode of screen-printed cells was covered by a film of elecrosynthesized molecularly imprinted polypyrrole (e-MIP); differential pulse voltammetry (DPV) was the selected method for the analyte detection. The ascorbic acid molecules were suc-cessfully entrapped in the polypyrrole film, creating the recognition sites. The best results were obtained after polypyrrole overoxidation and performing the measurements in phosphate buffer solution 0.05 M/KCl 0.1M at pH 7.5. The comparison with the bare and the not imprinted polypyrrole-modified electrodes showed the highest selectivity and reproducibility of the e-MIP-based sensor. The developed method was applied to assess ascorbic acid in farmaceutical products obtaining values not significantly different from the declared content.

Fleets of drones have attracted a lot of attention from the research community in recent years. One of the biggest challenges in deploying such systems is localization. While GNSS localization systems can only be effective in open outdoor environments, new solutions based on radio sensors (e.g., ultra-wideband) are increasingly being used for localization in various situations and environments. However, self-localization without prior knowledge of anchor positions remains an open problem which, for example, makes it impossible to track a moving target. In this article, we provide a comparison of different variants of gradient descent-based algorithms, with a new improved variant, for solving the localization problem using relative distance measurements and multilateration. It is applied to self-localization of anchors and tracking targets using ultra-wideband distance sensors. A realistic simulation of drone tracking and anchors’ localization is performed to demonstrate the robustness and accuracy of the proposed approach.

The paper presents the development of cheap and selective Paper-based Analytical Devices (PADs) for Pd(II) determination. The PADs were obtained with an azoic ligand, (2-(tetrazolylazo)-1,8 dihydroxy naphthalene-3,6,-disulphonic acid), termed TazoC, and filter paper as the substrate. The orange TazoC-PADs interact quickly with Pd(II) solutions by forming a complex purple-blue-colored already at a very acidic pH (lower than 2). The dye complexes no other metal ions at such an acidic media, making TazoC-PADs highly selective to Pd(II) detection. Besides, at higher pH values, other cations, for example, Cu(II) and Ni(II), can interact with TazoC through the formation of stable and pink-magenta-colored complexes; however, it is possible to quantify Pd(II) also in the presence of other cations using a multivariate approach. Indeed, by applying Partial Least Square regression (PLS), the spectra of the TazoC-PADs were related to the Pd(II) concentrations both when present alone in solution and also in the presence of Cu(II) and Ni(II). The PLS models correctly predicted Pd(II) concentrations in unknown samples and tap water spiked with the metal cation.

Polycyclic aromatic hydrocarbons (PAHs) have emerged as promising materials for organic electronics, including organic photovoltaics (OPVs), organic field-effect transistors (OFETs), and organic light-emitting diodes (OLEDs). Particularly, non-hexagonal ring-fused PAHs are highly desirable due to their unique optoelectronic properties. Herein, a new redox-active azulene-perylene diimide triad 1 and its ring-fused counterpart, diazulenocoronene diimide 2, were synthesized and fully characterized by a combination of NMR, cyclic voltammetry, spectroelectrochemistry, and UV-visible absorption spectroscopy. Density functional theory (DFT) and time-dependent DFT (TD-DFT) calculations were performed to gain further insight into various electronic transitions. Interestingly, we found that the adaptive response to acids and bases manifests itself in a reversible two-color-change that can be attributed to changes in the chemical structures.

This paper presents the design and implementation of a versatile IoT testbed utilizing the openHab platform along with various wireless interfaces, including Z-Wave, ZigBee, WiFi, 4G-LTE, and IR, and an array of sensors for motion, temperature, luminance, humidity, vibration, UV, and energy consumption. First, the testbed architecture, setup, basic testing, and collected data results are described. Then, by showcasing a typical day in the laboratory, we illustrate the testbed's potential through the collection and analysis of data from multiple sensors. The study also explores the capabilities of the openHab platform, including its robust persistence layer, event management, real-time monitoring, and customization. The significance of the testbed in enhancing data-collection methodologies for energy assets and unlocking new possibilities in the realm of IoT technologies is particularly highlighted.

The increase and diversity of low-cost Air Quality (AQ) sensors, as well as their flexibility and low power consumption, offers us the opportunity to integrate them into a broad AQ wireless sensor networks with the aim of enabling real-time monitoring and higher spatial sampling density of pollution in all parts of the cities. Considering that the vast majority of the population lives in these cities and the increase in respiratory/allergic problems in a large part of the population, it is of great interest to offer services and applications to improve their quality of life. In the ECO4RUPA project we focus on this kind of service, proposing an inclusive and intelligent routing ecosystem carried out by using a network of low-cost AQ sensors with the support of 5G communications along with official AQ monitoring stations, assisted with artificial intelligence to improve the AQ monitoring data and by spatial interpolation techniques to enhance its spatial resolution. The goal of this service is to calculate healthy walking and/or cycling routes according to the particular citizen’s profile and needs. We provide and analyse the results of the proposed route planner under different scenarios (different time tables, congestion road traffic and routes) and different user’s profiles, with special interest on citizens with asthma and pregnant women, since both require special needs. In summary, our approach can lead to an approximately average reduction in pollution exposure of 17.82%, while experiencing an approximately average increase in distance travelled of 9.8 %.

During the last decades the quantitative description of electrical and magnetotransport properties of solid-state materials has been a remarkable challenge in materials science. Recently, the discovery of a novel class of materials, the topological semimetals, has led to a growing interest for the full understanding of their magnetotransport properties. In this review, the strong interplay among topology, band structure and carrier mobility in recently discovered high carriers mobility topological semimetals is discussed and their effect on their magnetotransport properties is outlined. The huge magnetoresistance effect, especially in the Hall transverse configuration, and a new version of a three-dimensional quantum Hall effect observed in high-mobility Weyl and Dirac semimetals are reviewed. The design of novel quantum sensors based on solid-state semimetals is also encouraged.

The process of blood coagulation, wherein circulating blood transforms into a clot in response to internal or external injury, is a critical physiological mechanism. Monitoring this coagulation process is vital to ensure that blood clotting occurs neither too rapidly nor too slowly. Anticoagulants, a category of medications designed to prevent and treat blood clots, require meticulous monitoring to optimise dosage, enhance clinical outcomes, and minimise adverse effects. This review article delves into the various stages of blood coagulation, explores commonly used anticoagulants and their targets within the coagulation enzyme system, and emphasises the electrochemical methods employed in anticoagulant testing. Electrochemical sensors for anticoagulant monitoring are categorised into two types. The first type focuses on assays measuring thrombin activity via electrochemical techniques. The second type involves modified electrode surfaces that either directly measure the redox behaviour of anticoagulants or monitor the response of standard redox probes in the presence of these drugs. The review provides a comprehensive list of different electrode compositions and their detection and quantification limits. Additionally, it discusses the potential of employing a universal calibration plot to replace individual drug-specific calibrations. The insights presented are anticipated to significantly contribute to the sensor community's efforts in this field.

In the context of improving aircraft safety, this study focuses on the development and evaluation of a graphene-based ice detection system using an environmental chamber. The research is driven by the need for more accurate and efficient ice detection methods, crucial in mitigating in-flight icing hazards. The methodology employed involves testing flat graphene-based sensors in a controlled environment, simulating a variety of climatic conditions that could be experienced in an aircraft during its entire flight. The environmental chamber enabled precise manipulation of temperature and humidity levels, thereby providing a realistic and comprehensive test bed for sensor performance evaluation. The results were significant, revealing the graphene sensors’ heightened sensitivity and rapid response to the subtle changes in environmental conditions, especially the critical phase transition from water to ice. This sensitivity is the key to detecting ice formation at its onset, a critical requirement for aviation safety. The study concludes that graphene-based sensors, tested under varied and controlled atmospheric conditions, exhibit a remarkable potential in enhancing ice detection systems for aircraft. Their lightweight, efficient and highly responsive nature makes them a superior alternative to traditional ice detection technologies, paving the way for more advanced and reliable aircraft safety solutions.

The existence of low-cost and accurate tools that can equip the First Responders (FRs) to detect trapped victims and provide insights about their health condition in the aftermath of a disaster, is imperative. To address the problem of detecting trapped victims behind walls or debris, we have developed a tool that exploits an Ultra-Wide Band (UWB) radar sensor for data collection and Machine Learning (ML) algorithms for data analysis. To evaluate the efficacy of our approach, we collected data from nine humans, both in standing and lying down positions. Next, we applied various ML algorithms to the collected dataset for two discrete sub-tasks that are of interest from an FR’s perspective. The first task is the detection of the victim’s presence, where the algorithms attained more than 95% accuracy and F1-Score. The second task is the estimation of the distance between the radar sensor and the victim, where the tool showed an average error of less than 40 cm.

This article describes a novel electrochemical on-chip biosensor that utilizes anti-PSA antibody (Ab) and silver nanoparticles (AgNPs) to enhance the sensing and detection capability of prostate specific antigen (PSA) in the blood. The AgNPs are prepared, characterized, and applied onto a silicon photonic on-chip biosensing receptor platform designed to enhance the accurate detection of PSA. The AgNPs were synthesized by a chemical reduction method using silver nitrate (AgNO₃) as the precursor. Transmission electron microscopy (TEM), selected area electron diffraction (SAED), energy dispersion X-ray spectroscopy (EDS), small angle X-ray scattering (SAXS), X-ray diffraction (XRD), and light microscopy were among the methods used in the characterization and analysis of the AgNPs. Each stage of the immunosensor fabrication was characterized using cyclic voltammetry. The proposed immunosensor was applied in the detection of PSA, a prostate cancer biomarker, with a high sensitivity and a limit of detection of 0.17 ng/mL over a linear concentration range of 2.5 to 11.0 ng/mL. The immunosensor displayed good stability and was selective in the presence of interfering species like immunoglobulin (Ig) in human serum, ascorbic acid (AA), and diclofenac (Dic). The detectivity and sensitivity are significantly higher than previous reports on similar or related technologies.

Multiwalled Carbon Nanotubes (MWCNTs) is more efficient for fabrication modern design of silicone rubber (SR) that used in industrial engineering applications; it has been embedded in room temperature vulcanization silicone rubber (RTV-SR) matrix for controlling in dielectric characterization. Frequency dielectric measurements were performed for multiwalled carbon nanotubes SR/MWCNT nanocomposites. Hence, the dielectric properties of modern design SR/MWCNT nanocomposites has been deduced as experimental work done to clarify the benefit of filling MWCNT with different patterns inside dielectrics. In variant thermal conditions (up to 40oC), it has been investigated that the new behaviors of SR/MWCNT nanocomposites dealing with nanotechnology techniques for designing new dielectric behaviors of insulation materials. Finally, this research succeeded to characterize dielectric constant, electric modulus and dielectric loss of SR/MWCNT nanocomposites with respect to traditional silicon rubber under variant thermal conditions and frequency response analysis (FRA) according to using certain types and concentrations of MWCNTs.

A sensitive electrochemical sensor based on AuPtPd trimetallic nanoparticles functionalized multi-walled carbon nanotubes coupled with chitosan modified glassy carbon electrode (GCE/CS/MWCNTs-AuPtPd) for the rapid detection of bisphenol A (BPA) was proposed. AuPtPd trimetallic nanoparticles were first assembled on MWCNTs to obtain MWCNTs-AuPtPd nanocomposite. Then the MWCNTs-AuPtPd was further dispersed on the surface of chitosan modified electrode surface to fabricate the GCE/CS/MWCNTs-AuPtPd sensor. Due to the superior catalytic properties of MWCNTs-AuPtPd and the good film formation of chitosan, the constructed sensor displayed good performances for BPA detection. The structural morphology of CS/MWCNTs-AuPtPd was characterized by many methods, such as SEM, UV-vis and TEM. Under the optimal conditions, the designed sensor showed a linear range from 0.05 to 100 µM for BPA detecting with a low detection limit of 1.4 nM. The designed sensor was further used to realize the determination of BPA in real samples and the recoveries ranged from 94.4% to 103.6%. The results demonstrated that the electrochemical sensor designed by CS/MWCNTs-AuPtPd nanocomposites was reliable and could be a useful tool for the monitoring of food safety.

Drones are being used more and more frequently and in various ways to attack people and critical infrastructures, which increases their level of danger and makes early detection and risk assessment even more difficult. There is no ultimate drone sensor. Rather, drones can only be effectively detected, if suitable sensor technologies are integrated within a system. Among the best suited sensorics for this purpose are radar and optical sensors, because the advantage of the radar, given by the long detection range, can be well combined with the additional visual-based information gained from a camera in the mid- and short-range, where usually the radar fails detecting micro drones. In this paper, a modular drone detection and assistance system MODEAS is presented, which can be used to automatically detect and track drones within a range up to some kilometers on the sky, but also in complex urban environments, where buildings and vegetation offer a perfect background for camouflage. The system provides an early detection of flying objects as potential drones, when those are not at all or only as small dots visible for the human eye. Main strengths of the system are the robust AI detection to differentiate such an object against clutter (birds, clouds) and its further classification by model and payload recognition, the latter aspect being considered as an indication of dangerousness. Moreover, once a drone is detected, the system follows it automatically, precisely and smoothly with a high-resolution pan-tilt-camera, measuring the distance to the sensor station with a laser rangefinder, compute the geocoordinates and visualize them live on a map. To improve the precision of the detection, a multisensorial fusion of all sensor detections is performed. Furthermore, alarms may be generated when a drone enters a restricted area.

Objective: The aim of this study was to provide a new machine learning method to determine temporal events and inner-cycle parameters (e.g., cycle, poles and skis contact and swing time) in cross-country roller ski skating on the field, using a single deported inertial measurement unit (IMU). Methods: The developed method is based on long short-term memory neural networks to detect poles and skis initial and final contact with the ground during the cyclic movements. Eleven athletes skied four laps of 2.5 km at low and high intensity using skis with two different rolling coefficients. They were equipped with IMUs attached to the upper back, lower back and to the sternum. Data from force insoles and force poles were used as reference system. Results: The IMU placed on the upper back provided the best results, as the LSTM network was able to determine the temporal events with an accuracy ranging from 49 to 55 ms and the corresponding inner-cycles parameters were calculated with a precision of 63 to 68 ms. The method detected 95% of the events for the poles and 87% of the events for the skis. Conclusion: The proposed LSTM method provides a promising tool for assessing temporal events and inner-cycle phases in roller ski skating showing the potential of using a deported IMU to estimate different spatio-temporal parameters of human locomotion.

Accurate and reliable measurement of real-world walking activity is clinically relevant, particularly for people with mobility difficulties. Insights on walking can help understand mobility function, disease progression, and fall risks. People living in long-term residential care environments have heterogeneous and often pathological walking patterns, making it difficult for conventional algorithms paired with wearable sensors to detect their walking activity. We designed two walking bout detection algorithms for people living in long-term residential care. Both algorithms used thresholds on the magnitude of acceleration from a 3-axis accelerometer on the lower back to classify data as “walking” or “non-walking”. One algorithm had generic thresholds, while the other used personalized thresholds. To validate and evaluate the algorithms, we compared the classifications of walking/non-walking from our algorithms to the real-time research assistant annotated labels and the classification from an algorithm validated on a healthy population. Both the generic and personalized algorithms had acceptable accuracy (0.83 and 0.82 respectively). The personalized algorithm showed the highest specificity (0.84) of all tested algorithms, meaning it was the best suited to determine input data for gait characteristic extraction. The developed algorithms were almost 60% quicker than the previously developed algorithms, suggesting they are adaptable for real-time processing.

Electrochemical sensors have been used for many decades. Yet, modeling of such sensors used in electrolysis mode is poorly documented, especially in the case parallel action of multiple gases. Those ones are of great interest since they constitute the first brick to bring information on natures and concentrations of a gaseous mixture composition thanks to grey box modeling of sensors array for example. Based on Butler Volmer’s equations, a model assuming parallel reactions at gold cathode has been introduced in this article and confronted to experimental results. Establishment of the model is based on the extraction of 3 variables: the charge transfer coefficient “α”, the reaction order γ, and the reaction constant rate k0. Tests performed without pollutants and with different concentrations of oxygen could be nicely fitted by the model. Then, the influence of polarization current on the 3 variables of the model has been evaluated showing a clear influence on the constant rate and the reaction order. Also, increasing the polarization current enabled us to get selectivity to oxidant gases. Similarly, the effect of the oxygen concentration was evaluated. Results showed that, in this case, the charge transfer coefficients “α” obtained for oxidant gases is quite different that the ones obtained in the polarization current varying conditions. Therefore, the model will be interesting in situations where polarization current and oxygen content are not varied together. Variation of polarization current can be quite interesting to get increased information for multivariate analysis purpose in constant oxygen content situations. Besides, other parameters have are required for applications in which the oxygen content is bound to change like exhaust gases or combustion.

Porous structures and micropatterning surfaces play a crucial role in the development of highly sensitive force sensors. However, achieving these two conductive architectures typically requires complex materials synthesis and expensive manufacturing processes. In this study, we introduce a novel conductive composite film featuring a porous/micropyramid hybrid conductive architecture, which is achieved through a straightforward process of materials mixing and one-step screen printing. By utilizing a deep eutectic solvent in the ink component, micropores are induced in the printed composite, while the mesh of the screen mask acts as a template, resulting in a micropyramid film surface. We have successfully realized highly sensitive flexible force sensors with multifunctional capabilities for perceiving normal force and shear force.

Multiple Gateways (GWs) provide network connectivity to Internet of Things (IoT) sensors in a Wide Area Network (WAN). The End Nodes (ENs) can connect to any GW by discovering and acquiring its periodic beacons. This provides GW diversity and hence improves coverage. If the GWs are within vicinity to each other, and they keep sending periodic beacons to be discovered, the result is interference and collisions. In this study, the impact of such intra-network interference is analyzed to determine the maximum number of GWs that can co-exist within a given urban neighborhood. The paper shows the relationship between beacon collisions and the resulting packet loss rates in a given urban environment. The expected collision rates are calculated for the Medium Access Control (MAC) layer. The eventual packet loss rates are calculated with the MAC and Physical (PHY) layers combined. For this purpose, a new co-channel interference model is presented. The model calculates the average Carrier to Interference ratio (C/I) averaged across all the colliding events. It takes into account the partial overlap durations and the relative power of each colliding signal. The model shows that a collision does not always cause a packet loss. Packet losses occur if there is a collision and if the C/I is below a threshold. The performance evaluation is presented using a combination of analytical and simulation methods. The analytical methods provide the theoretical foundation, and have been used to validate the simulation results. Furthermore, the system models are developed from experimental data obtained from measurements with real hardware. Numerical results are provided with a low bit rate Gaussian Frequency Shift Keying (GFSK) modulation at the PHY layer, which is derived from the IEEE 802.15.4 standard specification. This paper provides guidance on selecting the right GFSK modulation parameters for such low bit-rate and narrow bandwidth IoT applications. The analysis and simulation results show that larger beacon intervals help in reducing beacon loss rates, at the cost of larger beacon acquisition latency. On the flip side, the gateway discovery latency reduces with increasing GW density thanks to abundance of beacons.

This study introduces an innovative integration of hyperbolic metamaterials (HMMs) and photonic crystals (PtCs), each possessing unique dispersion properties that effectively manipulate the propagation of light. We present a PtC waveguide consisting of arrays of HMM nanorods, denoted as HMM PtCs. This waveguide configuration enables the realization of a high figure of merit (FOM) nano-sensor. By modifying the refractive indices of the surrounding materials, the PtC waveguide exhibits alterations in absorption and transmission, allowing for the detection of temperature, pressure, and material variations. Numerical methods were employed to demonstrate the remarkable efficiency of this proposed system, achieving a sensitivity of 324.16 nm/RIU (refractive index unit) and an impressive FOM of 469.58 RIU−1. These results signify a substantial improvement over surface plasmonic sensors, which typically exhibit limited FOMs. As a consequence, the HMM PtC waveguide sensor emerges as an exceptionally appealing option for photonic sensing applications. The proposed HMM PtC waveguide holds vast potential across diverse fields, including biology, medicine, and clinics, representing an exciting advancement for both industry and scientific research.

Turbidity is an important water quality parameter, especially for drinking water. The ability to actively monitor the turbidity level in Drinking Water Distribution Systems is of critical importance to the safety and wellbeing of the public. Traditional turbidity monitoring methods involve manual collection of water samples at set locations and times followed by laboratory analysis, which are labor intensive and time consuming. Fiber-optic measurement permits real-time, in-situ turbidity monitoring. But the current technology is based on plastic fibers, which suffer from high optical attenuation and hence are unsuitable for large-scale remote monitoring. In this paper, we report the demonstration of a fiber-optic turbidity sensor based on multi-mode glass fibers. The system uses a single fiber to both deliver laser light into the water sample and collect the back-scattered light for detection. A balanced-detection scheme is utilized to remove the common-mode noise to enhance the turbidity sensitivity. Highly linear turbidity responses are obtained and a turbidity resolution as low as 0.1 NTU is achieved. The test unit is also shown to have excellent reproducibility against repeated measurements and good stability against temperature changes. Turbidity measurement in real environmental matrices such as tap water and pond water is also reported with an assessment of the impact of flow rate. This work demonstrates the feasibility of future large scale distributed fiber-optic turbidity monitoring networks.

In this study, Silicon Carbide (SiC) nano-particle based serigraphic printing inks were formulated to fabricate highly sensitive and wide temperature range SiC printed thermistors. Initially, commercial silver ink was screen printed to fabricate inter-digitated electrodes (IDE’s) onto flexible Kapton® substrate via screen printing. Thermistor inks with different weight ratios of SiC nano- particles dispersed in polyimide resin matrix were fabricated. The SiC-polyimide temperature sensing inks were screen printed atop the IDE structures to form fully printed thermistors and encapsulated with a adhesive backed polyimide film for humidity inhibition. The high temperature tolerance of the Kapton® allowed the the sensors to be tested over a wide temperature range form 25◦C to 170◦C. The printed SiC thermistors exhibit excellent repeatability and stability over 15 hours of continuous operation. Optimal device performance was achieved with 30 wt.% SiC-polyimide ink. We report highly sensitive devices with a temperature coefficient of Resistance (TCR) of -0.556 %/◦C, a thermal coefficient of 502 K (β-index) and an activation energy of 0.08 eV which are comparable with printed thermistors previous reported. Further, the thermistor demonstrates an accuracy of ±1.35◦C which is well within the range offered by commercially available high sensitivity thermistors. SiC thermistors exhibit a small 6.5% drift due to changes in relative humidity between 10-90 %RH and a 4.2 % drift in baseline resistance after 100 cycles of aggressive bend testing at a 40°angle. The use of commercially available low cost materials, simplicity of design and fabrication techniques coupled with the chemical inertness of the Kapton® substrate and SiC nanoparticles paves the way to use all-printed SiC thermistors towards a wide range of applications where temperature monitoring is vital for optimal system performance.

The recently explored synergistic combination of graphene-based materials and deep eutectic solvents (DESs) is opening novel and effective avenues for developing sensing devices with optimized features. In more detail, remarkable potential in terms of simplicity, sustainability, and cost-effectiveness have been demonstrated for sensors, resulting in the creation of hybrid devices with enhanced signal-to-noise ratio, linearity, and selectivity. Therefore, this review aims to provide a comprehensive overview of the currently available scientific literature discussing investigations and applications of sensors that integrate graphene-based materials and deep eutectic solvents, with an outlook for the most promising developments of this approach.

The increasing regulatory pressure to monitor and reduce GHG emissions and air pollutants requires cost-effective methods for their surveillance. The most common technique used for scientific investigations on gas concentration monitoring in barns are accurate but expensive and with a complex maintenance. This research study analysed the potential use of a low-cost portable measurement devices for the measurement of ammonia (NH3) and carbon dioxide (CO2) concentrations in an open dairy barn. A comparison between gas concentrations acquired at different heights from the floor by using portable devices and those acquired by a photoacoustic infrared multigas spectroscope (i.e., reference measurement) in the same sampling locations was carried out to determine the precision of the low-cost portable devices. The performance of low-cost portable devices was statistically analysed by the application of the one-way analysis of variance, correlation analysis and regression analysis. The results showed a significant difference between gas concentration values at various heights from the floor for both NH3 and CO2. The correlations between concentrations acquired by the low-cost portable device and the INNOVA were statistically significant (r=0.83; P<0.001) for gas concentrations monitored at 0.4 m from the floor. Compared with the reference measurement device, the low-cost devices were effective in the monitoring of NH3 concentrations at 0.40 m from the floor though it underestimated them in the barn at increasing of the height from the floor, whereas the device was not adequate for CO2 concentrations. In detail, the relative measurement error of the low-cost devices compared to INNOVA was reduced close to the floor during NH3 concentration measurements. Within these limitations, this device could be useful for monitoring NH3 concentration in the barn and to assess variation in NH3 concentrations mainly related to the animal occupied zone. Further efforts are needed in this field of research to identify low-cost device that could simplify emission estimation from open dairy barns.

Through the use of Smart Sensor Networks (SSN), Marine Observatories (MO) provide continuous ocean monitoring. Deployed sensors may not perform as intended due to the heterogeneity of SSN devices’ hardware and software when combined with the Internet. Hence, SSN are regarded as complex distributed systems. As such, SSN designers will encounter challenges throughout the design phase related to time, complexity, sharing diverse domain experiences (viewpoints), and ensuring optimal performance for the deployed SSN. To this end, we describe in this article how we extended our previously proposed ArchiMO meta-model and design tool by extending an Enterprise Architecture Framework based on the ArchiMate Modeling Language. This extension proposes the incorporation of new Underwater Environmental Constraints (UEC) for SSN in ArchiMO which is coupled with the fusion of sensors with Artificial Intelligence. This serves as the basis for generating a new version of our ArchiMO design tool, which incorporates the new added constraints and invokes the AI created Database. To illustrate our proposal, we use the newly generated ArchiMO to create a model in the MO domain. Furthermore, we use our self-developed domain-specific model compiler to produce the relevant simulation code. Throughout the design phase, our approach contributes to handle and control the uncertainties and variances of the provided quality of service that may occur during the performance of the SSN, hence reducing the design activity’s complexity and time. It provides a way to share the different viewpoints of the designers in the domain of SSN.

A reduced order model is developed to monitor aeroengines condition (defining their degradation from a baseline state) in real-time, by using data collected in specific sensors. This reduced model is constructed by applying higher order singular value decomposition plus interpolation to appropriate data, organized in tensor form. Such data are obtained using a detailed engine model that takes the engine physics into account. Thus, the method synergically combines the advantages of data-driven (fast online operation) and model-based (the engine physics is accounted for) condition monitoring methods. Using this reduced order model as surrogate of the engine model, two gradient-like condition monitoring tools are constructed. The first tool is extremely fast and able to precisely compute `on the fly’ the turbine inlet temperature, which is a paramount parameter for the engine performance, operation, and maintenance, and can only be roughly estimated by the engine instrumentation in civil aviation. The second tool is not so fast (but still reasonably inexpensive) and precisely computes both, the engine degradation and the turbine inlet temperature at which sensors data have been acquired. These tools are robust in connection with random noise added to the sensors data and can be straight forwardly applied to other mechanical systems.

Three-dimensional flexible piezoresistive porous sensors have been used in health diagnosis and wearable devices. By utilizing 3D printed sacrificial mold casting with highly conductive polymer composites, porous sensors with high conductivity and complex structures were achieved. Traditional conductive polymer composites are usually heated using external heat sources, which are time and energy consuming. However, in this study, conductive porous sensors with triply periodic minimal surface (TPMS) structures were manufactured using self-resistance electric heating by utilizing the conductive nature of the polymers. The porous structures were designed based on Diamond (D), Gyroid (G), and I-WP (I) unit cells of the TPMS. The use of self-resistance electric heating has improved the compression performance and piezoresistive response of the structures. Among these structures, the D-based structure exhibited the maximum response strain (61 %), with a corresponding resistance response value of 0.97, which increased by 10.26 % compared to that of the structures heated by using the external heat sources. This study offers a new perspective on designing and optimizing porous materials with specific functionalities, particularly in the realm of flexible and portable piezoresistive sensors.

This paper presents a study about the integration of Piezoelectric Energy Harvesting Systems (PE-EHS) in building envelopes for powering Fiber Bragg Grating (FBG) sensors, enabling efficient and low-consumption monitoring with the objective to leverage Structural Health Monitoring (SHM). The research includes preliminary tests conducted in a real environment to validate the PE-EHS when fully integrated into the façade, capturing mechanical vibrations generated mainly by wind loads. Based on these activities, the final configuration of PE-EHS is defined to provide a complete system for façade monitoring. This integrated system includes the Piezoelectric Generator (PEG), Supercapacitor (SC), Power Conditioner Circuit (PCC), Fibre Optic Sensing (FOS) Interrogator, and the IoT Gateway trans-mitting measurement data within an Internet of Things (IoT) monitoring platform. This configuration is tailored to address the challenges related to the structural integrity of building envelopes. Results demonstrate a potential for a stand-alone solution in the façade sector, but, raising issues for certain limitations, requiring further investigation. In particular, the study emphasizes constraints related to the energy production of PE-EHS for façade integration. It highlights the necessity to carefully consider these limitations within the broader context of their applicability, providing insights for the informed deployment of Piezoelectric Energy Harvesting technology in building envelope monitoring.

This work demonstrates that microbial fuel cells (MFCs), optimized for energy recovery, can be used as an effective tool to detect the presence of antibiotics in water-based environments. MFCs directly convert chemical energy of organic matter in electrical energy thanks to electroactive biofilms. The efficiency of the conversion process can be significantly affected by the presence of contaminants acting as toxicants for the biofilm. In the present work, we demonstrate that MFCs can successfully detect the presence of antibiotic residues in water and water-based electrolytes associated to the food industry, especially using honey as a new and more complex electron donor. The effectiveness of MFCs to sense antibiotics is here demonstrated for tetracycline that was added to both water and water/honey electrolytes with a minimum concentration close to 3.5 μg⁄kg. MFCs not only efficiently detect the presence of tetracycline in both the electrolytes, but also recover the same performance after each cycle of exposure, showing to a be very robust and reliable technology for both biosensing and energy recovery.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

In recent years, strain sensors have penetrated various fields. The capability of sensors to convert physical signals into electrical signals is of great importance in healthcare. However, it is still challenging to obtain sensors with high sensitivity, large operating range and low cost. In this paper, a stretchable strain sensor made of a double-layer conductive network, including a biomimetic multilayer graphene-Ecoflex (MLG-Ecoflex) substrate and a multilayer graphene-carbon nanotubes (MLG-CNTs) composite up-layer was developed. The combined action of the two layers led to an excellent performance with an operating range of up to 580% as well as a high sensitivity (gauge factor (GFmax) of 1517.94). In addition, a pressure sensor was further designed using the bionic vein-like structure with a multi-layer stacking of MLG-Ecoflex/MLG-CNTs/MLG-Ecoflex to obtain a relatively high deformation along the direction of thickness. The device presented a high sensing performance (up to sensitivity of 0.433 kPa-1), capable of monitoring small movements of the human body such as vocalisations and gestures. The good performance of the sensors together with a simple fabrication procedure (flip-molding) make it potential for some applications, for example, human health monitoring and other areas of human interaction.

Monitoring the quality of stored bulk grain is generally done using temperature cables hung from silo roofs. Little investigation has been done into the effects of number of sensors and their placement in terms of reliability of the monitoring system with regard to making stored grain quality management decisions. A previously developed 3D finite element simulation model was verified and used to investigate these aspects. In the first study, a silo was loaded with about 228.6 Mg (9000 bushels) of maize and six temperature cables were placed in the grain mass. The maize was aerated continuously for a period of two weeks, and the cable sensor temperatures were compared to the predicted temperatures which were in close agreement with the observed readings. The standard error of prediction ranged from 2.0 to 3.7°C. In the second study, 15 and 30 sensors were placed at manufacturer recommended depths and horizontal locations in the grain mass of three silo sizes (i.e., 11x11, 14.6x14.6 and 14.6x18.3 m diameter by eave height). The average grain temperatures predicted by the 15 and 30 sensors over a one-year simulation period were compared to the average grain temperatures predicted for the entire grain mass (1968, 3052, and 3204 mesh nodes). The number of sensors needed to monitor stored grain temperatures reliably in the three silo sizes investigated heavily depended on whether the aeration control strategy achieved a sufficiently low temperature by the time the aeration fans were turned off and sealed ahead of the non-aerated storage period. Fifteen or 30 sensors were sufficient to monitor grain temperatures during the aeration cooling period but for the two larger silo sizes more than 30 sensors would be needed during the storage period. As silo size increased, and surface-to-volume ratio decreased, grain temperatures remained lower during the storage period. Results support the best management practice recommendation of leaving cooled grain cold and not warming it up in the spring ahead of storage into the summer.

In urban areas like Chicago, daily life extends above ground level due to prevalence of high-rise buildings where residents and commuters live and work. This study examines the variation in fine particulate matter (PM2.5) concentrations across building stories. PM2.5 levels were measured using PurpleAir sensors, installed between April 8 and May 7, 2023, on floors one, four, six, and nine of an office building in Chicago. Additionally, data were collected from a public outdoor PurpleAir sensor on the fourteenth floor of a condominium located 800 meters away. Results show that outdoor PM2.5 concentrations peak at 14 meters height, then decline by 0.11 μg/m3 per meter elevation, especially noticeable from midnight to 8 AM under stable atmospheric conditions. Indoor PM2.5 concentrations increase steadily by 0.02 μg/m3 per meter elevation, particularly during peak work hours, likely caused by greater infiltration rates at higher floors. Both outdoor and indoor concentrations peak around noon. We find that indoor and outdoor PM2.5 are positively correlated, with indoor levels consistently remaining lower than outside levels. These findings align with previous research suggesting decreasing outdoor air pollution concentrations with increasing height. The study informs decision-making by community members and policymakers regarding air pollution exposure in urban settings.

This review delves into the growing field of flexible and stretchable strain sensors utilized in human gait analysis, focusing on determining knee bending angle and muscle activities when a human subject walks. Recent advancements have enabled these sensors to accurately capture biomechanical parameters while accommodating the body's natural movements. We examine the principles underlying these sensors' design and fabrication techniques, emphasizing their flexibility, stretchability, and biocompatibility for seamless integration into wearable systems. Through critical evaluation of existing methodologies, we assess the reliability and validity of these sensors in quantifying gait parameters. Furthermore, we discuss this technology's clinical and research implications, highlighting its potential in personalized rehabilitation and sports performance optimization. We provide an overview of flexible strain sensors and their application for analyzing human walking gait, especially for observing walking gait in rehabilitation programs. First, we present the basic working principles of various flexible strain sensors. Second, by the application of flexible strain sensors as walking gait monitoring. Finally, current challenges and future opportunities in this research area are discussed. By synthesizing current knowledge and outlining future directions, this review aims to provide insights for researchers and practitioners seeking to leverage flexible and stretchable strain sensors for comprehensive human gait analysis.

The substrate N1, N3, N5 -tris(2-hydroxyphenyl)benzene-1,3,5-tricarboxamide (Sensor A) was prepared in the reaction of 1,3,5-benzenetricarboxylic acid (trimesic acid) and o-aminophenol in ethanol. The prepared organic sensor fulfills the chemiluminescent requirements including luminophore, spacer, and suitable binding receptor that distress the probe's luminescent features, providing selective and sensitive detection of mercury and iron ions in aqueous solutions. The sensor selectively detects mercury and iron ions in a water matrix containing various metal ions including sodium, calcium, magnesium, zinc, and nickel. Strong and immediate binding was observed between mercury ions and the substrate at pH 7.0 with a binding affinity toward Hg (II) enhanced by nine folds higher than that observed for iron sensor binding affinity, which makes the substrate a distinctive luminescence sensor for mercury detection at ambient conditions. The sensor shows a linear response toward Hg (II) in the concentration range from 4.2 x 10-5 to 2.0 x 10-8 M with a limit of detection of 1.0 x 10-8 M. Further, Sensor A provides linear detection for iron ions in the range from 1.5 x 10-3 to 1.5 x 10-8 M. The measured adsorption capacity of Sensor A toward mercury ions ranged from 1.25 to 1.97 mg/g and the removal efficiency from water samples reached 98.8% at pH 7.0. The data demonstrate that Sensor A is an excellent probe for detecting and removing mercury ions from water bodies.

The method for quantitative analysis is based on the direct measurement of the analyte using differential pulse voltammetry (DPV), exploiting its oxidation peak. Calibration curves are set up to evaluate the figures of merit of the analytical method (LOD, LOQ, linear range). The application of the sensor for the dosing of GA in real matrices is carried out by analyzing non-alcoholic and alcoholic beverages and comparing the results with those reported in the literature and with the content of total polyphenols determined by the Folin-Ciocalteu method. In all cases, concentrations of GA align with those previously found in the literature for the beverages examined. Moreover, the values are always lower than the total polyphenols content; this demonstrates the good selectivity of the sensor that can discriminate the target molecule from other polyphenols present.

This review delves into the critical role of automation and sensor technologies in optimizing parameters for thermal treatments within electricity power generation. The demand for efficient and sustainable power generation has led to a significant reliance on thermal treatments in power plants. However, ensuring precise control over these treatments remains challenging, necessitating the integration of advanced automation and sensor systems. This paper evaluates the pivotal aspects of automation, emphasizing its capacity to streamline operations, enhance safety, and optimize energy efficiency in thermal treatment processes. Additionally, it highlights the indispensable role of sensors in monitoring and regulating crucial parameters such as temperature, pressure, and flow rates. These sensors enable real-time data acquisition, facilitating immediate adjustments to maintain optimal operating conditions and prevent system failures. It explores the recent technological advancements, including machine learning algorithms and IoT integration, which have revolutionized automation and sensor capabilities in thermal treatment control. Incorporating these innovations has significantly improved the precision and adaptability of control systems, resulting in heightened performance and reduced environmental impact. This review underscores the imperative nature of automation and sensor technologies in thermal treatments for electricity power generation, emphasizing their pivotal role in enhancing operational efficiency, ensuring reliability, and advancing sustainability in power generation processes.

Telemonitoring and telerehabilitation have shown promise in delivering individualized healthcare remotely. We introduce STASISM, a Sensor-Based Telerehabilitation and Telemonitoring System, in this work. This platform has been created to facilitate individualized telerehabilitation and telemonitoring for those who need rehabilitation or ongoing monitoring. To gather and analyze pertinent and validated physiological, kinematic, and environmental data, the system combines a variety of sensors and data analytic methodologies. The platform facilitates customized rehabilitation activities based on individual needs, allows for remote monitoring of patients' progress, and offers real-time feedback. To protect the security of patient data and to safeguard patient privacy, STASISM also provides secure data transmission and storage. The platform has the potential to significantly improve the accessibility and efficacy of telerehabilitation and telemonitoring programs, enhancing patients' quality of life and allowing healthcare professionals to provide individualized care outside of traditional clinical settings/

As formally is known, nanozymes are the nanomaterials or nanoscale materials which reveal enzyme-like properties. These nanomaterilas can be utilzied instead of the natural enzymes for simulation of enzymatic reactions in harsh environmental conditions. Among different nanoscale enzyme-like materials, the majority of them reveal peroxidase-like activity, due to the high catalytic efficiency and stability of peroxidase-like nanozymes, they had been widely utilized for sensing and detection via constructing the colorimetric and fluorescence-based analytical and bioanalytical sensors. There are several high impact nanozymatic sensors which reported in the literature. Although the review articles published in this field, however, the current reviews focus on the introducing nanozyme field not description on the best articles published in this filed. Hence, this article aimed to present a brief introduction on the nanozyme-based chemistry with emphasizing on the historical overview of recent nanozymatic sensors. In this regard the best nanozymatic sensors which published over 2016-2023 were briefly described and overviewed.