This paper investigates the influence of sample size and layer height on the elastic modulus of samples 3D printed by fused filament fabrication (FFF). Cubic samples of different sizes from either a stiff thermoplastic polymer (polycarbonate (PC)) or a soft polymer (thermoplastic polyurethane (TPU)) were printed at three different layer heights: 0.1 mm, 0.2 mm, and 0.4 mm. The samples were imaged using micro-computed tomography to visualize porosity and tested under compression. The results indicate that the elastic modulus of TPU varied with sample size, demonstrating size effects due to high porosity. In contrast, PC samples had a low void volume fraction and did not demonstrate statistically significant size effects on the elastic modulus. The variations in elastic modulus due to layer height were statistically significant for both materials. The highest elastic modulus was observed at 0.2 mm layer height for both materials across different sample sizes, which can be attributed to low void volume fractions. The study develops process-structure-property relations for PC and TPU samples manufactured by FFF. It provides new insights into the design guidelines for FFF based on the size effects. The results indicate that variations in mechanical properties due to size effects must be considered during the design stage for TPU to accurately predict the material’s behavior. Additionally, the locations of the printed parts that are subjected to higher loads should be printed closer to the heated print bed due to the lower void volume fraction observed in the section of the samples printed adjacent to the heated print bed.

The seismic events of 2015 in Nepal exposed the challenges associated with constructing earthquake-resistant 2-story self-built stone masonry structures in high-elevation rural regions, especially post-disaster. The Department of Urban Development and Building Construction (DUDBC) provided designs that failed to preserve the local architectural landscape and craftsmanship while adding unfamiliar knowledge and technology. To address the challenges related to architecture, structure, and socio-economic concerns in designing and implementing post-earthquake houses, a need-based building development framework is required for standardized practice. This study presents a novel framework to assess, design, and implement a self-built house after a disaster, consisting of five stages: 1) post-disaster problem assessment, 2) need identification, 3) material selection, 4) design development, and 5) validation and implementation. Based on this framework, we proposed a novel gabions building construction technology for two-story stone masonry structures that effectively mitigate post-disaster challenges such as logistic, resilience, and socioeconomic aspects while improving disaster resiliency specifically in the high-elevation rural areas of Nepal. The proposed two-story gabion building preserves architectural values, enhances structural integrity, and provides cost-effectiveness when compared with its DUDBC peer models while providing much-needed relief to the vulnerable community. The proposed resilient house, G- 2.1, utilizes locally sourced materials and craftsmanship, and innovative gabion technology that ensures affordability and facilitates knowledge transfer. The contribution of this study includes a development framework and a two-story gabions house that is most suitable for self-built post-disaster reconstruction and resilient to local architecture and socio-economic conditions while providing structural integrity and safety.

Wireless Sensor networks (WSNs) are gaining more and more research interest due to their ability to monitor large areas more or less independent. However, their reliability is an important issue, since their system reliability is influenced from a hardware, a data and an energetic point of view due to different factors like loading conditions, signal attenuation and battery lifetime. Regarding these issues, the positions of sensor nodes have to be chosen correctly to maximize the system reliability, which has to be considered during the development of new products equipped with WSNs. In this paper, an approach to estimate a WSNs system reliability during the development phase based on the analysis of the measurements on the example of strain measurements in finite elements (FE) models is presented. For that, the part under consideration is divided into regions with similar strains by the use of a Region Growing Algorithm (RGA). Afterwards, the WSN’s configuration is analyzed regarding its reliability in accordance to the data paths and measurement redundancy due to the sensor positions in the found measuring regions. This methodology is tested on an exemplary WSN configuration at an aircraft wing box under bending load and was found to work very well regarding the estimation of the hardware perspective on the system reliability. Therefore, the methodology and the developed algorithm show potentials for optimizations in sensor node positions for better reliability results.

This study examines the optimization of ground source heat pump (GSHP) systems and energy piles for sustainable urban development, with a focus on Southeast Asia. GSHPs, which utilize geothermal energy for indoor HVAC needs, offer a sustainable alternative to traditional systems by utilizing consistent subsurface temperatures for heating and cooling. The study highlights the importance of understanding thermal movement within the soil, especially in soft marine clays prevalent in Southeast Asia, to improve GSHP system efficiency. Using a one-dimensional finite-difference model, the study examines the effects of soil thermal conductivity and density on system performance. The results show that GSHP systems, especially when integrated with energy piles, significantly reduce electricity consumption and greenhouse gas emissions, underscoring their potential to mitigate the urban heat island effect in densely populated areas. Despite challenges posed by the region's hot and humid climate, which could affect long-term effectiveness, the study highlights the need for further study, including field experiments and advanced modeling techniques, to optimize GSHP configurations and fully exploit geothermal energy in urban environments. The study's insights into soil thermal dynamics and system design optimization contribute to the advancement of sustainable urban infrastructure development.

This paper studies the flexural behavior of the bridge deck link slabs made with the Polyvinyl Alcohol-Strain Hardening Cementitious Composites (PVA-SHCC). Tensile and flexural properties of the PVA-SHCC with four volume fractions, i.e., 0%, 1%, 1.5%, and 2%, were evaluated first. Next, using the similarity theory, composite models with a geometric similarity ratio of 1: 5 were designed to represent the bridge deck with the link slabs. The models considered three materials for link slabs, including concrete, cement mortar and self-compacting PVA-SHCC; and two different curing ages at 7 and 56 days. Bending tests were performed to investigate the flexural behavior of the models. Based on the fractal theory, cracking characteristics of the models with different types of link slabs were compared, and the relationship between Df and the flexural behavior of the models were studied. Numerical models were built to correlate with the results from the bending tests. It is illustrated that the flexural behavior of the self-compacting PVA-SHCC link slab is better than that of concrete and cement mortar link slabs, where the crack initiation and propagation can be postponed.

Accurate cloud quantification is essential in climate change research. In this work, we construct an automated computer vision framework by synergistically incorporating deep neural networks and finite sector clustering to achieve robust whole sky image-based cloud classification, adaptive segmentation, and recognition under intricate illumination dynamics. A bespoke YOLOv8 architecture attains over 95% categorical precision across four archetypal cloud varieties curated from extensive annual observations (2020) at a Tibetan highland station. Tailor-made segmentation strategies adapted to distinct cloud configurations, allied with illumination-invariant image enhancement algorithms, effectively eliminate solar interference and substantially boost quantitative performance even in illumination-adverse analysis scenarios. Compared with the traditional threshold analysis method, the cloud quantification accuracy calculated within the framework of this paper is significantly improved. Collectively, the methodological innovations provide an advanced solution to markedly escalate cloud quantification precision levels imperative for climate change research, while offering a paradigm for cloud analytics transferable to various meteorological stations.

This study explores the multifaceted influence of litter size, maternal care, exercise, and aging on rats' neurobehavioral plasticity and dentate gyrus microglia dynamics. Body weight evolution revealed a progressive increase until maturity, followed by a decline during aging, with larger litters exhibiting lower weights initially. Notably, exercised rats from smaller litters displayed higher body weights during mature and aged stages. Dentate gyrus volumes showed no significant differences among groups, except for aged sedentary rats from smaller litters, which exhibited a reduction. Maternal care varied significantly based on litter size, with large litter dams showing lower frequencies of caregiving behaviors. Behavioral assays highlighted the detrimental impact of a sedentary lifestyle and reduced maternal care/large litters on spatial memory, mitigated by exercise in aged rats from smaller litters. Microglial dynamics in the layers of dentate gyrus revealed age-related changes modulated by litter size and exercise. Exercise interventions mitigated microgliosis associated with aging, particularly in aged rats. These findings underscore the complex interplay between early-life experiences, exercise, microglial dynamics, and neurobehavioral outcomes during aging.

Although researchers have proposed various indentation size effect (ISE) models, these models often involve different form and number of parameters that can make our wonder which is the best in existed ISE models. Three types of ISE test data, namely, normal ISE, reverse ISE and transition of normal to reverse ISE, are used to evaluate the sixteen ISE models. The comparatively study indicates that H-J, N-G-Fs, N-G-H, N-G-A and N-G-Qs models can accurately predict the normal ISE. The reason for this is that the friction stress that is not related to dislocation activities or the indentation size effect of plastic zone has been introduced into these models. Therefore, these two factors should be considered in future ISE models. The sixteen ISE models are originally proposed to describe the normal ISE of different materials. However, to our surprise, some of these models are able to capture the reverse ISE and the transition of normal to reverse ISE of different materials. The determination coefficients (DC) of the sixteen ISE models are also determined for different materials. For reverse ISE, the highest DC value for NiCSi, TC4 and PED Ni are given by the EXP, N-G-Fs and N-G-A models, respectively. For the transition of normal to reverse ISE, the N-G-YC, N-G-Fs, and N-G-H models produce the maximum DC for ZrO2, Cu and Y2O3-ZrO2, respectively. Moreover, the mean DC of the N-G-Fs model is the maximum among the sixteen ISE models, followed by the N-G-H model, but they cannot accurately predict the reverse ISE. Therefore, the N-G-Fs and N-G-H models should be further modified to accurately predict the reverse ISE.

This paper presents a compartmental model aimed at investigating the pharmacokinetics of medical THC after oral administration. The model was developed to be multi-compartmental, describing the kinetics of THC and its metabolites in bodily tissues. Utilizing the law of mass action, the model was converted into ordinary differential equations (ODEs), illustrating the rate of concentration changes of THC and its metabolites in each compartment. Subsequently, we applied the nonstandard finite difference (NSFD) method to construct numerical solution schemes. These schemes were implemented in the MATLAB program, along with estimated pharmacokinetic rate constants. The results of the investigation demonstrate that the simulation curves depicting the plasma concentration-time profiles of THC and THC-OH closely resemble the actual data samples, indicating that this model accurately describes the pharmacokinetics of medical THC and its metabolites. Moreover, the model exhibits predictive capabilities regarding the pharmacokinetics of THC and its metabolites in various tissues. Consequently, the model serves as a valuable tool for enhancing our understanding of the pharmacokinetics of THC and its metabolites and for guiding adjustments to dosage and administration durations for oral medical THC products.

Abstract—The static and fatigue analysis of plates with holes, made of 2D woven roving composites, is conducted. The parametrization of convex holes is proposed. Experimental results of specimens without holes and with different shapes of notches are discussed. The fatigue behaviour is considered with the use of the low cycle fatigue method. The analysis is supplemented by the numerical finite element modeling. The present work is an extension of the results discussed in the literature. The finite element modeling of plates with holes is presented in details in Ref [1-3] including also the problems of the accuracy. The experimental results and the form of specimens are shown in Ref [4]. Two parametrical description of static and fatigue behaviour of plates with holes characterizes the goal and the novelty of the paper. The fuzzy approach is employed to reduce the number of experimental data [5].

Sample size using prevalence has been one of the most important medical research methodologies and has been used in original articles more often than any other statistical tool available. The simple formula consists of variables interdependent and it is as important to understand how they influence each other as it is to learn to use the formula to calculate the sample size. With the choice of different amounts of precision and levels of confidence available to a medical researcher, it should be of paramount importance to understand what a slight change in choosing the parameter would mean at the end of the research. Understanding of different Z values, Levels of precision, and ranging Prevalence is required to understand the effect on the sample size and subsequently on the research. Topological representation using parameter ranges can be used to demonstrate this relationship.

The rehabilitation of the road embankments alongside the irrigation canal, which is constructed on a Bangkok soft clay foundation, has resulted from land use growth for several decades. As a result, the embankment is always confronted with the problem of instability. Numerous articles have demonstrated that rapid drawdown of the water level in the canal could be one of the most significant reasons, whereas vehicle cyclic loading may potentially contribute to some effect of the embankment failure. To explore and assess the effects of the influence factors, the finite element method (FEM) and conventional and dynamic triaxial approaches were employed. The study also investigated the consequences of varying thicknesses of soft clay and cyclic loading with different magnitudes and frequencies. Consequently, cyclic loading can lead to an augmentation in strain distribution and excess pore water pressure. Likewise, more significant deformation and excess pore water pressure were induced by a lower frequency and deeper thickness of soft clay compared to a higher frequency and thinner thickness. In brief, vehicle repetitive loading is one of the primary factors contributing to embankment failure, with the threshold stress being approximately three-fourths of the undrained shear strength. In contrast, threshold strain is approximately one to two-fold of the monotonic strain condition.

Estimating parameters for multiple datasets can be time consuming, especially when the number of datasets is large. One solution is to sample from multiple datasets simultaneously using Bayesian methods such as adaptive multiple importance sampling (AMIS). Here we use the AMIS approach to fit a von Misses distribution to multiple datasets for wind trajectories derived from a Lagrangian Particle Dispersion Model driven from a 3D meteorological data. The primary objective is to characterise the uncertainties in wind trajectories in a form that can be used as inputs for predictive models of wind-dispersed insect pests and pathogens of agricultural crops for use in evaluating risk and in planning mitigation actions. Our results show that AMIS can significantly improve the efficiency of parameter inference for multiple datasets.

Quantitative determination of the critical size of inclined coal pillar in old goaf water affected area is of great significance for water damage prevention and safe mining. The critical size of inclined waterproof coal pillar is derived by using theoretical analysis, numerical calculation and field engineering practice for the stability of the waterproof coal pillar in old goaf water affected area of 1303 working face of Dananhu I mine in Xinjiang region. Firstly, a force model of inclined waterproof coal pillar was established to reveal the law that the critical size of the coal pillar increases with the increase of coal seam inclination under the action of asymmetric load. Then, numerical simulation was applied to reveal the dynamic evolution process of plastic deformation-destabilization-destruction of section coal pillar under the influence of mining and single-side water pressure, and the critical size of waterproof coal pillar in study area was determined to be 19.09m. Finally, measures such as pumping and pressure relief and slurry reinforcement were adopted to reduce the deformation rate of the roadway on side of waterproof coal pillar, which ensured the stability of the coal pillar and roadway and the safe recovery of the working face.

Wind turbines (WTs) are clean a renewable energy source that has been growing in popularity in recent years. Gearboxes are complex, expensive, and critical components of WT, which are subject to high maintenance costs and several stresses including high loads and harsh environments that can lead to failure with significant downtime and financial losses. This paper focuses on the development of a digital twin-based approach for the modelling and simulation of WT gearboxes with the aim to improve their design, diagnosis, operation, and maintenance by providing insights into their behavior under different operating conditions. Pow-erful commercial computer-aided design tools (CAD) and computer-aided engineering (CAE) software are embedded into a computationally efficient multi-objective optimization framework (modeFrontier) with the aim of maximizing the power density, compactness, performance, and reliability of the WT gearbox. This entails minimizing its weight, volume, and maximum stresses and strains achieved without compromising efficiency. The 3D CAD model of the WT gearbox is carried out using SolidWorks, the Finite Element Analysis (FEA) to obtain the stresses and strains fields are modelled using Ansys Workbench, while the multibody kinematic and dynamic system is analyzed using MSC Adams. The method has been successfully applied to different case studies to find the optimal design and analyze the performance of the WT gearboxes. Simulation results can be used to identify potential failure modes and optimize gearbox design to improve performance, extend service life and relia-bility, thereby ensuring proper operation over its lifetime and reducing maintenance costs.

A novel compressible real gas 1D finite volume thermofluid network modelling methodology is proposed that can be applied in the analysis of supercritical CO₂ (sCO2) power cycles. It is applied to simulate centrifugal compressor performance via a mean line approach that directly solves the mass, energy, and momentum balance equations for the discretized flow channels within the machine along with the associated loss models, component characteristics, and applicable compressible real gas equation of state. This can be integrated seamlessly with the rest of the power cycle components like pipes, valves, heat exchangers, etc., thereby eliminating the need for static performance maps and the associated difficulties to ensure similarity over the whole range of operation. This direct simulation of the internal flows also makes it possible to do integrated cycle design optimization that includes the geometry of the compressors, and to simulate fast transients for dynamic analysis. The methodology was applied to simulate well-documented air and sCO2 centrifugal compressors and compared the generated results with that of conventional thermofluid network incompressible and compressible ideal gas approaches. The results indicate that the proposed compressible real gas approach can capture the stagnation pressure changes and isentropic efficiencies with good accuracy for both cases over the whole range of mass flow rates and shaft rotational speeds. In contrast, the conventional thermofluid network incompressible and compressible ideal gas approaches are only applicable in selected regions of the fluid property regime and suffer from discretization errors and inappropriate treatment of the relationship between stagnation and static pressures. Furthermore, comparative analyses between the newly proposed approach and the traditional mechanical energy balance method are performed, showing that the latter approach needs to be discretized more finely through the compression process to correctly capture the polytropic compression path shape, whereas the former more accurately captures the stagnation pressure changes through the analyzed compressors with only a single increment per compressor component.

This paper introduces a low-tech capacitive micromachined ultrasonic transducer (CMUT) designed with low environmental footprint materials. The fabrication process involves a copper plate as the fixed bottom electrode, a polymer-based adhesive as a dielectric material, and an aluminum foil as the top electrode.Finite element simulations include studies of displacement, mechanical stresses, and eigenfrequency. Experimental measurements validate the device's electromechanical behavior, showing an eigenfrequency of 88.6 kHz and a displacement of 22 pm. The low-tech CMUT demonstrates potential for applications such as ultrasonic actuation and energy harvesting, offering simplicity, biocompatibility, and low environmental impact. While not directly ready for applications, these transducers provide hands-on experience with technology similar to high-performance silicon-based implementations. These low-tech MUTs are perfect practical case studies for teaching purposes, combining simulation and experimental validation.

This study aims to examine the non-volatile Particle Number (PN) emissions of a retrofitted Heavy-Duty Spark-Ignition (HD-SI) engine powered by liquefied petroleum gas (LPG) under both steady-state and transient conditions. The engine was tested under seven steady-state operating points to investigate the PN behavior and Particle Size Distribution (PSD) upstream and down-stream of the Three-Way Catalyst (TWC). This analysis intends to assess the impact of including particles with diameters ranging from 10 nm to 23 nm in the total particle count, a consideration for future regulations. The study employed the World Harmonized Transient Cycle (WHTC) for transient conditions to encompass the same engine working region used in the steady-state analysis. A Dekati FPS-4000 diluted the exhaust sample to measure the PSD and PN for particle diameters between 5.6 nm and 560 nm using the TSI-Engine Exhaust Particle Sizer (EEPS) 3090. Findings indicate that PN levels tend to increase downstream of the TWC under steady-state conditions in operating points with low exhaust gas temperatures and flows (equal to or less than 500 °C and 120 kg/h). Furthermore, the inclusion of particles with diameters between 10 nm and 23 nm leads to an increase in PN emissions by 17.70% to 40.84% under steady conditions and by an average of 40.06% under transient conditions, compared to measurements that only consider particles larger than 23 nm. Notably, in transient conditions, most PN emissions occur during the final 600 seconds of the cycle, linked to the most intense phase of the WHTC.

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

The paper delves into the critical issue of damage detection within the guy cable of a truss steel mast, a pivotal component in structural integrity. It introduces a model wherein damage manifests as a localized cross-section reduction in a single element of the cable. Employing Discrete Wavelet Transform (DWT), a pioneering methodology, the study scrutinizes the behavior of the affected elements through static structural analyses. Signal decomposition via the Mallat pyramid algorithm facilitates comprehensive examination. Static displacements at the connection point between the cable and the truss mast serve as the measured variables. Through systematic investigation, the paper evaluates the impact of damage size and location, external loading force, and cable tension force on the efficacy of the proposed approach. Utilizing data derived from Finite Element Method (FEM) computations for wavelet analysis the authors substantiate the findings with numerical examples, thus offering valuable insights into damage detection strategies for structural health monitoring and engineering applications.

This study explores the significance of active suspension systems for vehicles with lower chassis compared to conventional ones, aiming at the development of future automobiles. Conventional linear MR (Magneto-Rheological) dampers were found inadequate in ensuring sufficient vibration control because the vehicle's chassis becomes lowered in the unmanned vehicles or purposed based vehicles. As an alternative, a rotary type of MR damper is proposed in this work. The proposed damper is designed based on pre-specified design parameters through mathematical modeling and magnetic field analyses. Subsequently, a prototype of the rotary MR damper identical to the design is fabricated, and effectiveness is shown through experimental investigations. In configuring the experiments, a proportional-integral (PI) controller is employed for current control to reduce the response time of the damper. The results presented in this work provides useful guidelines to develop a new type of MR damper applicable to various types of future vehicles’ suspension systems with low distance from the tire to the body floor.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

Leaf springs are suspension components constituted of several structural and assembly components. Once the leaves are assembled, a stress state due to the assembly process is developed. Thus, the quantification of the assembly stress level should be known in order to be accounted for in the structural design. The aim of this article is precisely to quantify the assembly stress level in parabolic leaf springs for railway freight wagons. An experimental method with the aid of extensometry is considered to evaluate elastic assembly stresses. Next, a numerical model of the leaf spring assembly process with the required boundary conditions is developed to support the experimental results and allow obtaining a distribution of surface stresses along the master leaf length. The development of this work resulted in a surface stress profile along the length of the master leaf generated by the assembly process, where the deviations of the numerical outcomes regarding the analysed spots with strain gauges are mostly of little relevance.

Implant-supported-screw-retained prostheses are really popular. Some of the most frequent complications have been mechanical complications. These include abutment screw loosening or even screw fracture. Using an intermediate abutment can offer several advantages. However, little literature has been found regarding how this affects the mechanical behavior of dental restorations. This study focuses on understanding the mechanical behavior of implant-supported restorations with a transepithelial component compared to those with a direct implant-supported restoration. It was carried out by using the Finite Element Method (FEM) and was experi-mentally validated. The results showed that in the case of transepithelial-supported restoration, the prosthetic screw mounted over the transepithelial component suffers higher stress than the one screwed directly to the implant. After applying a cyclic fatigue load, it is experimentally proven that, in the transepithelial-supported restorations, the fuse changes from being the screw that goes to the implant, to being the upper one. As a conclusion we can say that the use of an intermediate abutment in dental restoration not only provides better protection to the rest of the dental restoration but also allows easier repair in the event of a fracture. This can potentially lead to more efficient procedures and improved patient outcomes.

Recently perovskite solar cells have been paying attention of researchers. This comes from their high efficiency and stability. In this work, the change of some Optical and Electrical Properties of BaxFe(1-x)TiO4 thin films due to the change of the nanocrystal spacing and size were studied. A simple theoretical model based on the string theory was utilized to explain some of these empirical relations. The empirical results obtained indicated that an increase in the efficiency of the nano solar cell requires the energy gap to be narrow. Decreasing the nanocrystal size and spacing caused the energy gap to become narrower. The energy gap decreases also upon increasing the absorption coefficient and decreasing the transmission. This also requires increasing the conductivity and the magnetic permeability. The increase of the nanocrystal spacing decreases the absorption coefficient, electrical conductivity, and magnetic permeability, while it causes the transmission to increase. All these changes are explained using a simple string model beside Newton's laws. The capability of the string theory to explain this Nano quantum behavior comes from the fact that the string theory, like quantum theory, recognizes both the particle and the wave nature of the Nano system.

This investigation introduces an efficient method for assessing the reliability of semi-rigid steel frame connections in existing buildings, explicitly targeting the Top Angle and Seat Pad (TA-SP) semi-rigid connection commonly used in Australian cities' high-rise buildings. The moment capacity of these connections was examined through parameter power model testing, meticulously considering the bending, shear, and prying forces actions to determine the weakest elements in the connection system. A plastic hinge model was applied to ensure computational efficiency and accuracy in assessing the connections' ultimate strength. Comparatively, the finite element (F.E) method M−θ curves were introduced to scrutinise the nonlinear behaviour of the connection, providing validation for the predicted analytical approach. Further emphasis was placed on identifying the reliability of the weakest elements in the connection system, employing the First-Order and Second-Order Reliability Methods models to estimate their reliability index. The correlation between the model's failure probability and a percentile error was also explored, utilising Monte Carlo simulation reference for refined validation. Novel formulas and methodologies were introduced to compute the locked-chain-series system reliability, which accounts for the inherent material and geometric variability. The findings highlight the critical significance of the weakest element in determining the overall reliability of the existing TA-SP connection.

Keywords: liquid alloys, microstratification, dispersed particles, spontaneous dispersion, criteria for true (entropic) spontaneous dispersion, mechanisms of quasi-spontaneous dispersion, methods and results for assessing size of dispersed particles.

Brushless Direct Current Motors are significantly improved for using many electrical applications. The design investigation is increased year by year and most of the motor design researchers find out the superior efficiency of the BLDC motor. The traditional motor consumed more electrical power than BLDC motor. The design of BLDC motors that are compact, small, easy to control, save energy and light weight. Due to this fact, the design of BLDC motor should be analyzed to improve the motor characteristics performance. The research focuses on the design of BLDC motor performance using Taguchi Method and Response Surface Methodology (RSM) for Finite Element Method (FEM). Firstly, the Taguchi Method is applied to identify the optimization point of design parameters and consider using the reference model of actual BLDC electric fan motor with a rated power of 26Watts design. Based on the Taguchi Method to create the RSM is used to two-step optimization design performance using in FEM analysis. The performances of motor design proposed approach to provide the effeteness for motor design investigator. In this investigation aims the better structural performances in output power, torque, efficiency and torque ripple. The final design of proposed model achieved an energy efficiency is 10% higher than the reference design of prototype modes, the output power result is 10W higher this reference design. We can reduce the loss of the proposed motor design. Furthermore, the maximum torque can also increase the 0.032Nm of that design. The design simulation results were produced and studied by the FEM analysis of JMAG software. From the evaluation results, the configurations of reference model design are compared with the proposed design by using the three methods of motor design optimization showed the best characteristics for performance of motor investigation design.

As companies increasingly undergo digital transformation, the role of talent management pro-cesses becomes pivotal in enhancing overall organizational performance. The research addresses the significance of talent management in corporate digital transformation, examining whether variations in the digitalization of these processes can be attributed to company size. A qualitative approach was employed, utilizing a questionnaire, collecting responses from 202 organizations across diverse sectors. Findings reveal disparities in digitalization throughout the talent man-agement process, with pronounced presence in the attracting, selecting, and rewarding phases, but diminishing in deployment and development, further declining in planning. A positive cor-relation between company size and adoption of specific digital platforms was observed. Larger enterprises exhibit greater utilization of digital platforms in talent deployment and development. Moreover, corporate communication tools are consistently utilized in the rewarding phase, irre-spective of company size. These findings offer practical insights for organizations to optimize their digitalization strategies based on their scale, thereby contributing to more effective and tailored digitalization endeavors. The uniqueness of this research lies in its exploration of the in-fluence of company size on the digitalization of talent management processes and its potential to explain variations across different stages of these processes.

The ANSYS 2024R1 student edition was used to create a finite element model of a basketball rim and backboard. This finite element model included the use of steel for the rim and its mount, a tempered glass backboard, and an aluminum frame behind the backboard. After a mesh was created, fixed support boundary conditions were applied to the four corners of the aluminum frame. The subsequently calculated mode shapes and frequencies were compared to empirical modal analysis previously done at the United States Military Academy at West Point, New York. Four mode shapes and frequencies agreed rather well between the theoretical finite element analysis and previously published empirical modal analysis, specifically where the rim was vibrating in the vertical direction, which was the direction that the accelerometer was aligned for modal analysis. However, three mode shapes missed by the empirical modal analysis were found where the vibration of the rim was confined to the horizontal plane, which was orthogonal to the orientation of our accelerometer.

During the thinning process, in the semiconductor industry, residual stress from thin films can cause severe warpage in wafers, which can compromise their processability and packaging. This warpage can lead to bifurcation or buckling, making it important to understand this phenomenon for the manufacturing of large semiconductor wafers. We conducted a finite element analysis of the thinning process using ANSYS mechanical enterprise 2023/R2 to investigate the asymmetric curvatures resulting from bifurcation in a standard 300 mm Si (001) wafer. We induced an asymmetry in the system by applying a slight force on a point of the circumferential region perpendicularly to the substrate. We also simulated the compressive stress from the damaged layer formed during the thinning process and considered its influence on warpage and bifurcation in both linear and non-linear cases. We also included the influence of Earth's gravity induced deflection (GID) and investigated the influence of the compressive stress damaged layer on the grinding process of the whole wafer by adding a metal front layer to the ground back damaged wafer.

Parkinson’s disease (PD) is the second-most common neurodegenerative disorder worldwide and is diagnosed based upon motor impairments. Non-motor symptoms are well-recognized in PD, and peripheral neuropathy is a frequent but poorly appreciated non-motor sign. Study of how the central and peripheral sensory systems are affected can contribute to the development of targeted therapies and deepen the understanding of the pathophysiology of PD. Although the cause of sporadic PD is unknown, chronic exposure to the pesticide rotenone in humans increases the risk of development of PD. Here, we aimed to investigate whether peripheral neuropathy is present in a traditional model of PD. Mice receiving intrastriatal rotenone showed greatly reduced dopamine terminals in the striatum and reduction in tyrosine hydroxylase-positive neurons in the Substantia nigra pars compacta and developed progressive motor impairments in hindlimb stepping and rotarod but no change in spontaneous activity. Interestingly, repeated testing using gold-standard protocols showed no change in gut motility, a well-known non-motor symptom of PD. Importantly, we did not observe any change in heat, cold, or touch sensitivity, again based upon repeated testing with well-validated protocols that were statistically well-powered. Therefore, this traditional model fails to replicate PD, and our data again reiterate the importance of the periphery to the disorder that is PD.

Modal testing is a common step in aerostructure design, serving to validate the predicted natural frequencies and mode shapes obtained through computational methods. The strategic placement of sensors during testing is crucial to accurately measuring the intended natural frequencies. However, conventional methodologies for sensor placement are often time-consuming and involve iterative processes. This study explores the potential of machine learning techniques to enhance sensor selection methodologies. Three machine learning-based approaches are introduced and assessed, comparing their efficiency with established techniques. The evaluation of these methodologies is conducted using a numerical model of a beam to simulate real-world scenarios. The results offer insights into the efficacy of machine learning in optimizing sensor placement, presenting an innovative perspective on enhancing the efficiency and precision of modal testing procedures in aerostructure design.

This study employs Principal Component Analysis to examine cranial measurements obtained from both extant and fossil specimens spanning 38 species and comprising over 300 individuals within the subfamily Cervinae. Our findings elucidate craniometric distinctions among cervids characterized by varying body sizes and certain evolutionary adaptations. While our results generally corroborate previous assertions regarding the limited craniometric variability among plesiometacarpal deer, they also unveil specific cranial adaptations within certain genera and species. The Principal Component Analysis of craniometric data revealed that giant and large-sized deer display significantly broader ecomorphological diversity in cranial shape compared to small-sized deer. Secondly, small-sized deer exhibit greater uniformity in their cranial shape, appearing densely clustered on the factorial map. Thus, we conclude that body size imposes ecological constraints, limiting the available niches due to eco-physiological factors. The study demonstrates that endemic insular deer do not evolve consistent craniometric features attributable to insular isolation, while the cranial proportions of medium-to-small sized deer delineate a ubiquitous morphological archetype characteristic of numerous cervid taxa spanning diverse phylogenetic lineages and sharing comparable body sizes. This group of "Dama-like" deer, characterized by similar body size, metabolic rates, ecological needs, and cranial morphometry, is referred to here as the fundamental eco-physiological type, typical of warm regions within the Palearctic and Oriental biogeographic realms..

Traumatic Brain Injury represents a significant public health concern due to its role in traumatic death and disability, often caused by head impacts or rapid accelerations. Despite advancements in Finite Element Head Models, existing models primarily represent adult males, neglecting anatomical and physiological differences between genders and age groups. Additionally, the mechanistic roles of specific intracranial tissues, such as the dura mater, have conventionally been overlooked. To better understand the mechanical behavior of the brain and its injured regions in the context of TBI, including the dura mater, this study proposes the development of a Female Finite Element Head Model. This model, representative of a middle-aged female subject, was developed using medical image-derived geometry and finite element modeling techniques. The validation results demonstrate a similarity between the numerical displacement curves and those obtained experimentally. In the model with dura mater, the numerical results show analogous behavior to the experimental results, despite minimal variations in the amplitude of the curves. These advancements highlight the significance of including the dura mater in biomechanical brain modeling. Incorporating the dura mater in Finite Element Head Models produces more realistic results than models without it. This emphasizes the importance of enhancing biomechanical models to better represent anatomical complexity.

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

In this paper, comprehensive analysis of combined effect of major influencing parameters on heat transfer in the single U-tube BHE (sBHE) and double U-tube BHE (dBHE) with two independent circuits was performed by using validated numerical heat transfer model. Geometrical parameters, such as shank spacing (with maximum, average and minimum values) and borehole diameter (large, medium and small borehole sizes) and borehole depth (shallow, average and deep borehole depths) as well as thermal conductivity of soil and grout which ranges from minimum to high value were considered. The combined impact of these parameters was included under four major cases: 1) combined effect of borehole depth, borehole size and shank spacing; 2) combined effect of borehole depth, and soil and grout thermal conductivity; 3) combined effect of soil and grout thermal conductivity and borehole size; and 4) combined effect of soil thermal conductivity, borehole size and shank spacing. Each of these major cases has nine different design options of both sBHE and dBHE. Series of results of heat transfer per unit borehole depth were generated for all the considered various cases. With the given parameters, the BHE case that provides highest heat transfer among the various cases of sBHE and dBHE were obtained.

Currently, in some domestic and foreign mines, the backfill drilling pipeline experience a rupture phenomenon even when the wear degree is low. This results in a delay in production due to the filling becoming 'sick'. This paper presents, for the first time, the damage mechanism from a mechanical perspective and re-derives the anti-extrusion strength model of the backfill drilling pipeline. We investigate the influence of law on the anti-extrusion strength of pipelines from the perspective of stratum and cement ring. We then verify the theoretical and simulation results through engineering examples. The results demonstrate that the Mises stress criterion is a suitable modification principle for the anti-extrusion strength model of the backfill drilling pipeline. The anti-extrusion strength of the pipeline is related to the elastic modulus and Poisson's ratio of the stratum, and the thickness of the cement ring. It is negatively affected by the depth of the stratum. For hard strata, a cement ring with a smaller elastic modulus is suitable, while for soft stratum, a cement ring with a larger elastic modulus is recommended. When the missing angle of the cement ring is less than 60°, the stress concentration factor increases up to 2.2. The stress unloading capacity of the cement ring ranges from 32.7% to 37.8%, and optimal performance of the cement ring is achieved when it has high strength and low rigidity. The backfill filling pipeline of a copper mine abroad was destroyed due to external extrusion force exceeding its anti-extrusion strength value. The modified pipeline anti-extrusion strength model is 18.2% higher than the casing API strength value. This finding can inform the design of the backfill filling pipeline for China's kilometer-deep wells in the future.

Evaluation of structural behaviour of a masonry Venetian Church with pointed vault, is presented in this paper through an analysis following the neccessary steps of a monument study. Having a detailed geometric model and the material estimation, the finite element method was used in order the influence of specific structural parts of the structure like masonry butresses and walls connections to the structural behaviour are examined. The comparison of the eigenfrequencies which are estimated by in situ measurements and finite element modal analysis is used to model identification. The response spectrum analysis, the static analysis for subsidence of some parts and the transient analysis of a specific seismic excitation are used to evaluation of the church strength. Comparison of modal analysis results with the structural pathology is helpful to this research about the structural behaviour of the church.

The forest regeneration phase in Sweden commonly involves mechanical soil preparation followed by planting of Scots pine or Norway spruce seedlings. The prepared soil offers planting positions with different properties, including decreased damage by pine weevil (Hylobius abietis L.). Nitrogen fertilization can be applied at the time of planting to aid establishment of the seedlings. In this study we compared the effect of organic nitrogen-fertilization for different planting positions, and seedling sizes on early survival and growth of Scots pine and Norway spruce seedlings. The main planting positions were capped mound, hinge, and mineral soil. Seedlings planted close to organic material were categorized as “low quality positions”, since proximity to organic material increase pine weevil attraction. Higher mortality rates related to pine weevil damage were recorded for seedlings planted in the low-quality positions, regardless of seedling size or N-fertilization. Pine weevil attack rates increased with increasing seedling size. Growth was in general lowest in mineral soil positions. The effect of organic N-fertilization on growth was positive for spruce regardless of planting positions and seedling size, while depending on planting position and seedling size for pine, indicating that effects of organic N-fertilization depend on seedling species, -size and planting position.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional CAD models fail to fully represent bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTopology and Creo Parametric software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking into account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced finite element analysis (FEA) improves biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.

This study investigates the impact of specimen size on the mechanical properties of wood, specifically focusing on compression strength, elastic modulus, and Poisson's ratio. Compression tests were conducted using three different specimen sizes (20mm×20mm×30mm, 40mm×40mm×60mm, 60mm×90mm×90mm) in the longitudinal, radial, and tangential directions. Mechanical parameters, failure mechanisms, load-displacement curves, and stress-strain relationships were systematically analyzed for each size. The study also evaluated the influence of specimen size on the accuracy of finite element numerical simulations by utilizing the obtained mechanical parameters. The results reveal a significant correlation between compressive strength and specimen size, indicating a decrease in compressive strength with increasing specimen size. Conversely, elastic modulus and Poisson's ratio exhibit less sensitivity to variations in specimen size. Notably, parameters derived from small-sized specimens (20mm×20mm×30mm) exhibited substantial errors, while those obtained from medium-sized (40mm×40mm×60mm) and large-sized specimens (60mm×90mm×90mm) demonstrated greater reliability, providing precise results in finite element numerical simulations.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

A study was carried out in a Waste Sorting Plant (WSP) located in France and treating dry recyclable household waste (DRHW) as well as dry recyclable commercial and industrial waste (DRCIW). The aim was to investigate the exposure to bioaerosol and dust. The aim of the study was to assess the extent to which the measurement of concentration, species composition and particle size distribution can contribute to a better assessment of the biological risks associated with exposure. Both stationary and personal bioaerosol and dust samples were collect in the (WSP). The results confirm that waste and waste sorting activities are sources of airborne fungi. Indeed, ambient concentrations ranged from 7.3×103 to 8.5×105 CFU/m3 for culturable moulds and up to up to 4 mg/m3 for dust. Personal exposure to inhalable dust was found up to 3 mg/m3 for dust and ranged from 8.6×103 to 1.5×106 CFU/m3 for fungi. Airborne fungal communities were found to be dominated by the Penicillium genera in both bioaerosols and settled dust samples, followed by the Aspergillus, Cladosporium, Wallemia, Mucor, and Rhizopus genera. Fungi were carried by particles of aerodynamic diameters mainly between around 2.0 and 10.0 µm. The findings dealing with size distribution and biodiversity of bioaerosols suggest that employees are exposed to complex bioaerosols during their work and helps to make a finer diagnosis of the risks involved, which is often difficult in the absence of any OEL for bioaerosols in general.

A model of a single-server queuing-inventory system (QIS) with catastrophes and a finite waiting room for consumer customers (c-customers) has been developed. When a catastrophe occurs, all inventory in the system's warehouse is destroyed, but c-customers in the system are still waiting for restocking. In addition to c-customers, negative customers (n-customers) are also taken into account, which displaces one c-customers (if any). The policy (?, ?) is used to replenish stocks. If upon arrival of the c-customer the inventory level is zero, then according to Bernoulli’s scheme this c-customer is either lost or joining the queue. The mathematical model of the studied QIS is constructed in the form of a two-dimensional continuous-time Markov chain (2D CTMC). Exact and approximate methods for calculating the steady-state probabilities of constructed 2D CTMCs are developed and closed-form expressions are derived for calculating the performance measures. The results of numerical experiments are presented, demonstrating the high accuracy of the developed approximate formulas, as well as the behavior of performance indicators depending on the reorder point. In addition, an optimization problem is solved to obtain the optimal reorder point to minimize the expected total cost.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

To assess the impact of a deep learning (DL) denoising reconstruction algorithm applied to identical patient scans acquired with two different voxel dimensions, representing distinct spatial resolutions. This IRB approved prospective study was conducted at a tertiary pediatric center in compliance with the Health Insurance Portability and Accountability Act. We used a General Electric Signa Premier unit (GE Medical Systems, Milwaukee, WI) to acquire two DTI sequences of the left knee on each child at 3T: an in-plane 2.0 x 2.0 mm2 with section thickness of 3.0 mm and a 2 mm3 isovolumetric voxel, neither had an inter-section gap. We used a multi-band DTI acquisi-tion with fat-suppressed single-shot spin-echo echo-planar sequence (20 non-collinear directions; b-values of 0 and 600 sec/mm2). The MR vendor-provided a commercially available DL model applied with 75% noise reduction settings to same subject DTI sequences at different spatial res-olutions. We compared DTI tract metrics from both DL-reconstructed scans and non-denoised scans for femur and tibia, at each spatial resolution. Differences were evaluated using Wilcox-on-signed ranked test and Bland-Altman plots. When comparing DL versus non-denoised diffu-sion metrics in femur and tibia using the 2 mm x 2mm x 3 mm voxel dimension there were no significant differences between tract count (p = 0.1, p =0.14) tract volume (p = 0.14, p = 0.29), or tibial tract length (p=0.16); femur tract length exhibited a significant difference (p

Scaling up the production of power devices involves, in the semiconductor industry, the use of large semiconductor 8” and 12” wafers of Si or SiC. Their use implicates a successful an effective monitoring and control of wafer warpage, as the geometrical size of the substrate increases, as well as a command control on the degeneration of non-linear warpage into critical phenomena known as bifurcation or buckling.To mitigate the warpage, the use of taiko wafers, which consists of wafers having a thicker region on the rim region of the wafer, has been generally adopted in the production lines. In a previous work [1] we investigated the warpage of taiko wafers by introducing the concept of equivalent thickness, in the linear approximation, for the case of a front side metalized taiko wafer. However, as the thickness of the central semiconductor substrate region decreases the possibility that also the taiko wafer bifurcates emerges. For this reason, in this work we have investigated the occurrence of bifurcation or buckling in a taiko wafer. In particular, we implemented a finite element analysis method by using ANSYS Mechanical Enterprise 2023/R2 to investigate the phenomenon of bifurcation in a taiko wafer. The investigated system consisted of a 200 mm Si (001) front side metalized (FSM) taiko wafer, having a substrate thickness ranging from 100 µm to 400 µm, with a step height fixed to 450 µm. The FSM layer consisted of an Al layer of 4.5 µm thin. The system was subjected to a thermal load such that, getting cooled from a nominal temperature T to 25°C, the metal layer can develop a residual stress. To investigate the bifurcation, an asymmetry was induced in the system by applying a slight force on a point of the circumferential region perpendicularly to the substrate. The temperature investigated ranged from 30 °C to 170 °C. From this investigation, it results that also the bifurcation is mitigated by the taiko structure. Indeed, the bifurcation emerges at higher values of the stresses with respect to the case of flat wafers having the same size and thickness of the substrate. Moreover, the concept of equivalent thickness needs to be reformulated by taking into account of the bifurcation phenomenon. Indeed, from the warpage at the bifurcation point of the taiko wafer, we can determine an overall equivalent thickness of the taiko wafer.

Sustainable continuous cover forestry is defined and analyzed in several ways. The differential equation representing growth of the basal areas of individual trees, motivated by fundamental biological production theory by Lohmander (2017a), is analyzed and extended in different directions. From the solution of the differential equation, the basal area and the tree diameter are obtained as explicit functions of time. The diameter is a strictly increasing function of time. In the absence of competitors, the diameter increment is shown to be a strictly decreasing function of time. Hence, the diameter increment can also be interpreted as a strictly decreasing function of the diameter. Alternative forms of adjustment of the differential equation, with consideration of competition, are defined. If the competition is strong, with large trees in the vicinity of a particular tree, then the basal area increment, and the diameter increment, are reduced. The growth of a large tree is less sensitive than the growth of a small tree, to competition from other trees. Under strong competition, the basal area increment, and the diameter increment, are strictly concave functions of the size of the tree. The unique maximum of the diameter increment occurs at a higher diameter, if the competition increases. In dynamic equilibrium, the tree size frequency distribution is stationary. If natural tree mortality can be avoided via the harvest strategy, the tree size frequency distribution is a function of the size and competition dependent growth function, and the harvest strategy. Empirical tree size frequency data are used to simultaneously estimate parameters of a size and competition dependent growth function and the applied harvest strategy, via nonlinear optimization. The properties of the estimated growth function are consistent with the corresponding properties of the production theoretically motivated hypothetical function, and the properties of the estimated harvest strategy confirm the corresponding hypotheses. The R2 of the nonlinear regression exceeds 0.97. With access to an empirically estimated equilibrium tree size distribution, it is possible to: 1. Estimate size frequency relevant parameters of tree size and competition dependent growth functions for individual trees. 2. Estimate the applied harvest strategy. 3. Explain and reproduce the empirically estimated tree size equilibrium distribution.

Euler sums are alternating (or level two) extension of multiple zeta values (MZVs). Kaneko and Tsumura initiated the study of multiple T-values (MTVs), another level two generalization, by restricting the summation indices in the definition of MZVs to a fixed parity pattern. In this paper, we shall study finite MTVs and their alternating versions which are level two and level four variations of finite MZVs, respectively. We conjecture that all finite MZVs are in the Q-span of finite MTVs which in turn apparently lie in the span of finite Euler sums, and the inclusions are both proper. We shall first provide some structural results for Euler sums of small weights, guided by the author's previous conjecture that the finite Euler sum space of weight w is isomorphic to a quotient Euler sum space of weight w. Then, by utilizing some well-known properties of the classical alternating MTVs, we shall derive a few important Q-linear relations among the finite alternating MTVs, including the reversal, linear shuffle and sum relations. We then compute the upper bound for the dimension of the Q-span of weight w finite (alternating) MTVs for w<9, both rigorously using the newly discovered relations and numerically aided by computers.

Magnetic levitation vibration isolation platform are essential for testing space telescopes. This paper presents the design of a Large Air-Gap Voice Coil Motor (LAG-VCM) specifically for use in such platforms. The electromagnetic design of the voice coil motor begins with the Equivalent Magnetic Circuit Method, followed by the analysis and optimization of the motor design using Finite Element Analysis (FEA). Subsequently, a prototype was constructed and tested. The test results confirm that the prototype meets the design specifications and requirements.

The mushroom industry generates large amounts of stems, a co-product with valuable sensory and health characteristics. This work aimed to study the influence of particle size (L — &gt;0.510 mm; LI — 0.510-0.315 mm; SI—0.315-0.180 mm; S — &lt;0.180 mm) and species in the characterization and antioxidant activity of flours from stems of Agaricus bisporus (ABSF) and Pleurotus ostreatus (POSF). ABSF was rich in protein (14 g/100 g), calcium (428.23-700.77 mg/100 g), and sorbitol (22.57-26.60 g/100 g), while POSF in β-glucans (36.62-40.34 g/100 g) and linoleic acid (20.57-39.86 g/100 g of lipid). Both species were flush in amino acids with umami flavor. The highest hydration properties and oil holding capacity were exhibited in the S size of both species. ABSF showed elevated values for emulsifying activity than POSF. ABSF-S recorded the heightened antioxidant capacity in vitro, in consonance with the total phenolic compounds (0.91 mg/g). However, this antioxidant assays in POSF presented a positive correlation with β-glucans content. According to these results, there could be several food applications for these co-products, such as emulsifier stabilizer, sweetener or fortifier in the development of functional food.

Rebar cages form the skeletal framework of reinforced concrete structural members. They comprise longitudinal and transverse reinforcing bars, usually connected by tie wires. Past studies have identified tie-wire connections as the "weak links" in large, prefabricated rebar cages, leading to their failure during site handling and construction stages. Recent research has explored the use of mechanical U-bolt connectors to bolster stability and safety of rebar cages while reducing their vulnerability and risk of failure. This paper presents a comprehensive experimental and numerical investigation of a new type of mechanical connector, referred to as "Cage Clamp", to enhance rebar cage stability and safety. Component-level experimental tests are conducted to determine the force-displacement response of Cage Clamp connectors for crossbar connections in different degrees of freedom. The results highlight the remarkable strength and stiffness of Cage Clamp connectors, significantly outperforming traditional tie-wire connections. Furthermore, full-scale experimental tests are performed on a circular underground pile-shaft rebar cage with Cage Clamp connectors to assess its behavior under various site handling conditions. The data obtained from these experiments are used to construct and refine detailed 3D finite element models of the rebar cages, capable of capturing the complex behavior of rebar cages with Cage Clamp connectors. Using the numerical model, a sensitivity analysis is performed to assess the effect of the number of Cage Clamps on the deflection and stability of the rebar cage. The findings show that using cage clamps to connect pick-up rebar with lateral reinforcement at every 8 to 10 feet is sufficient to ensure the stability of the cage during typical site handling conditions. The results of this study serve as a basis for establishing analysis, design, fabrication, and handling guidelines for rebar cages, contributing to safe and efficient construction practices.

This study determines the equivalent stress intensity factor (SIF) model that best fits the experimental behavior of low-carbon steel under mixed mode (I and II). The study assessed Tanaka, Richard, and Pook's equivalent SIF models. The theoretical values used for comparison correspond to experimental results in a modified C(T) geometry by machining a hole ahead of the crack tip subjected to fatigue loads with a load ratio of R = 0.1. The comparison involved the SIF for six experimental points and the values computed through the numerical simulation. The Paris, Klesnil, and modified Forman-Newman crack growth models were used with each equivalent SIF to analyze the prediction in the estimated number of cycles. The Klesnil model showed the closest prediction since the error between the calculated and experimentally recorded number of cycles is the lowest. However, the material behavior reflects a reduced crack propagation rate attributed to plasticity in the crack tip. Results suggest that Asaro equivalent SIF conservatively estimates the element lifespan with increasing errors from 2.3% at the start of growth to 27 % at the end of the calculation.

This work is concerned with studying the change of some Optical and Electrical Properties of Ba_xFe_(1-x)TiO₄ thin films due to the change of the nano crystal size. Simple theoretical explanation based on the string theory was developed. The empirical results obtained indicated that the absorption coefficient, electrical conductivity, and the magnetic permeability increase upon decreasing the nano crystal size. However, the transmission coefficient, and the refractive index increase upon increasing the nano crystal size. All these changes are explained using a simple string model with the aid of Newton's laws. The capability of the string theory to explain this nano quantum behavior comes from the fact that the string theory recognize both the particle and the wave nature of the nano system. This is similar of course to the quantum approach which is based mainly on the dual wave particle nature of atomic systems and entities.

In the paper, a study of the performance of unmanned ground vehicle (UGV), establishes numerical simulation model of the chassis system by three-dimensional software and finite element analysis software. Based on the numerical modelling and analysis, the work focuses on study of the strength and stiffness of the vehicle's chassis and researched the distribution of stress and deformation under the extremal condition. The paper also presents an autopilot design with new cascade control system for an autonomous motion of an unmanned ground vehicle based on Proportional-Integral-Derivative (PID) and Feed-Forward (FF) control. The PID-FF controller is a part of dedicated for presented UGV used in a hybrid control system for precise control and stabilization, necessary to increase the vehicle motion stability and maneuvers precision. The hybrid PID-FF control system proposed for the ground vehicle model gives a satisfactory quality of control, while maintaining the simplicity of the control system. Presented tests performed in area of mechanical design and control analysis gives good results and proves usefulness of designed unmanned device.

In the process of use and manufacture, carbon fiber foam sandwich structures were often damaged by low-energy impact, resulting in performance degradation. Therefore, it was necessary to study the damage caused by low-speed impact of composite sandwich structures. In this paper, based on Hashin failure criterion, an equivalent finite element model of carbon fiber foam sandwich panel under low velocity impact was established. The model was used to simulate the damage of foam sandwich panel with [±45°/±45°/ (core) /±45°/±45°] ply structure under the impact energy of 10.58J, 21.17J, 31.75J and 42.34J. The simulation results of impact damage depth were compared with the experimental results. The error was less than 10%, which proved the rationality of the impact equivalent model. The model was used to predict and analyze the damage of foam sandwich panels with [±45°/ (core) /±45°], [±45°/ (0°, 90°) / (core) /±45°] and [±45°/ (0°, 90°) (core) / (0°, 90°) /±45°] ply structures under 21.17J impact energy. By comparing and analyzing the damage situation, impact force response time and impact velocity response time, the low energy impact resistance was analyzed. The results showed that increasing the number of ply structure of [±45°] can reduce the impact damage degree and improve the bearing capacity of sandwich panels.

Single-particle inductively coupled plasma mass spectrometry (spICP-MS) has been used for particle size measurement of diverse types of individual nanoparticles and micrometer-sized carbon-based particles, such as microplastics. However, its applicability to the measurement of micrometer-sized non-carbon-based particles such as silica (SiO2) is unclear. In this study, the applicability of spICP-MS to particle size measurement of non-porous/mesoporous SiO2 micro-spheres with a nominal diameter of 5.0 µm or smaller was investigated. Particle sizes of these microspheres were measured using both spICP-MS based on a conventional calibration approach using an ion standard solution and scanning electron microscopy (SEM) as a reference technique and the results were compared. The particle size distributions obtained using both techniques were in agreement within analytical uncertainty. The applicability of this technique to the detection of metal-containing protein-binding mesoporous SiO2 microspheres was also investigated. Bound iron (Fe)-containing proteins (i.e., lactoferrin and transferrin) of mesoporous SiO2 microspheres were detected using Fe as a presence marker for the proteins. Thus, spICP-MS is applicable to the particle size measurement of large-sized and non-porous/mesoporous SiO2 microspheres; it has considerable potential for element-based detection and qualification of bound proteins of mes-oporous SiO2 microspheres in a variety of applications.

This paper introduces an innovative approach to numerically model Structure-Soil-Structure Interaction (SSSI) by integrating the Boundary Element Method (BEM) and the Finite Element Method (FEM) in a coupled manner. To assess the accuracy of the proposed method, a comparative study is undertaken, comparing its outcomes with those generated by the conventional FEM technique. Alongside accuracy, the computational efficiency aspect is crucial for the analysis of large-scale SSSI problems. Hence, the computational performance of the coupled BEM-FEM method undergoes a thorough examination and is compared with that of the standalone FEM method. The results from these comparisons illustrate the superior capabilities of the proposed method in comparison to the FEM method. The novel approach provides more reliable results compared to traditional FEM methods, serving as a valuable tool for engineers and researchers involved in structural analysis and design.

It is commonly recognized that a ship’s ability to maintain stability is dependent upon the way its loads are distributed. This means making sure the center of gravity is sufficiently low and evenly distributed. Yet when a ship encounters turbulent water with extremely large wave amplitudes, load distribution is a critical factor in determining how stressed the ship becomes. In particular, this article examines several methods for increasing the ship's longitudinal strength to prevent ship structural damage during hogging and sagging. This research presents a number of proposed techniques to enhance the longitudinal strength of cargo ships in order to guarantee minimal stress and deformation during sagging and hogging. The first method is the stern-to-bow use of curved support structures to increase the longitudinal strength of a cargo ship. And another way to stiffen the lateral plate is the proposed use of different designs of the side plate, such as wavy curves, stars, etc. To further boost the strength, the lateral plate upper part is suggested to curve upward. A numerical simulation using ANSYS of the stiffened plate when subjected to uniform load distribution and fixed support on either end shows that there is a decrease in deformation of the plate when we use wavy curved plates compared with those of the other plate stiffening methods used, and furthermore, curving the plate on top increases its strength during sagging as well as hogging. Finally, the use of a curved support structure further enhanced the overall longitudinal strength of the vessel.

Abstract Background Context Pelvic ring fractures are becoming more common in the aging population and can prove to be fatal, having mortality rates between 10% and 16%. Stabilization of these fractures is challenging and often require immediate internal fixation. Therefore, it is necessary to have a biomechanical understanding of the different fixation techniques for pelvic ring fractures. Methods A previously validated three-dimensional finite element model of the lumbar spine, pelvis, and femur was used for this study. A unilateral pelvic ring fracture was simulated by resecting the left side of the sacrum and pelvis. Five different fixation techniques were used to stabilize the fracture. A compressive follower load and pure moment was applied to compare different biomechanical parameters including range of motion (contralateral sacroiliac joint, L1-S1 segment, L5-S1 segment), and stresses (L5-S1 nucleus stresses, instrument stresses) between different fixation techniques. Results Transiliac -trans sacral screw fixation at S1 and S2 showed the highest stabilization for horizontal and vertical displacement at the sacral fracture site and reduction of contralateral sacroiliac joint for bending and flexion range of motion by 165% and 121%, respectively. DTSF (Double transiliac rod and screw fixation) model showed highest stabilization in horizontal displacement at the pubic rami fracture site, while the L5_PF_W_CC (L5-Ilium posterior screw fixation with cross connectors) and L5_PF_WO_CC ( L5-Ilium posterior screw fixation without cross connectors) showed higher rod stresses, reduced L1-S1 (approximately 28%), and L5-S1 (approximately 90%) range of motion. Conclusions Longer sacral screw fixations were superior in stabilizing sacral and contralateral sacroiliac joint range of motion. Lumbopelvic fixations displayed a higher degree of stabilization in the horizontal displacement compared to vertical displacement of pubic rami fracture, while also indicating the highest rod stresses. When determining the surgical approach for pelvic ring fractures, patient-specific factors should be accounted for to weigh the advantages and disadvantages for each technique.

In this study, a new structure is proposed based on the body-centered cubic (BCC) lattice structure: adding a cubic truss in the center of the BCC structure, which is denoted by TLC (Truss-lattice-cube). The different dimensions of the central cube can affect the mechanical properties of the lattice structure notably. With a fixed length (15mm) of a unit cell, the optimal size for the central cube is determined to be 5 mm. Quasi-static compressive tests are performed on specimens made of Polylactic Acid (PLA) using additive manufacturing technology. The deformation characteristics of the new structure is analyzed in detail by experiments and numerical simulations. Compared to the BCC structure, the mechanical properties of the TLC structure are significantly improved. The initial flow stress of the TLC has been increased by 122% at a strain of 0.1; the specific strength has been enhanced by 293% at a strain of 0.5; and the specific energy absorption has been improved by 312% at the strain of 0.6. Printing defects in the lattice structure could deteriorate the mechanical property remarkably. In this work, incorporation of microcracks into the finite element model makes the simulation capture the influence of printing defects and improve the predictive accuracy of simulation significantly.

In the present paper, we efficiently solve the two-body problem for extreme cases such as those with high eccentricities. The use of numerical methods, with the usual variables, cannot maintain the perihelion passage accurately. In previous articles, we have verified that this problem is treated more adequately through temporal reparametrizations related to the mean anomaly through the partition function. The biparametric family of anomalies, with an appropriate partition function, allows a systematic study of these transformations. In the present work, we consider the elliptical orbit as a meridian section of the ellipsoid of revolution, and the partition function depends on two variables raised to specific parameters. One of the variables is the mean radius of the ellipsoid at the secondary, and the other is the distance to the primary. One parameter regulates the concentration of points in the apoapsis region, and the other produces a symmetrical displacement between the polar and equatorial regions. The three most used geodesy latitude variables are also studied, resulting in one not belonging to the biparametric family. However, it is in the one introduced now, which implies an extension of the biparametric method. The results obtained by the method presented here now allow a causal interpretation of the operation of numerous reparametrizations used in the study of orbital motion.

In this paper we address the approximation of the coupling problem for the wave equation and Maxwell's equations of electromagnetism in the time domain in terms of the electric field, by means of a nodal linear finite-element discretization in space, combined with a classical'explicit finite-difference scheme for the time discretization. Our study applies to the particular case where the dielectric permittivity has a constant value outside a sub-domain, whose closure does not intersect the boundary of the domain where the problem is defined. Inside this sub-domain Maxwell's equations hold. Outside this sub-domain the wave equation holds, which may correspond to the Maxwell's equations with a constant permittivity under certain conditions. We consider as a model the case of first order absorbing boundary conditions. Optimal error estimates that hold in natural norms under reasonable assumptions are given, among which lies a typical CFL condition for hyperbolic equations.

High temperature (HT) geothermal wells can provide green power 24h a day 7 days a week. Harsh environmental and operational conditions, long-term durability requirements of such wells require special cementitious composites for well construction. This paper reports a comprehensive assessment of geothermal cement composites in cyclic pressure function laboratory tests, field exposures in an HT geothermal well (300-350oC) as well as a numerical model to complement the experimental results. Performances of calcium-aluminate-cement (CAC)-based composites and calcium free cement were compared against reference Ordinary Portland Cement (OPC)/silica blend. The stability and degradation of the tested materials was characterized by crystalline composition, thermo-gravimetric, and elemental analyses, morphological studies, water-fillable porosity, and mechanical properties measurements. All CAC-based formulations outperformed the reference blend both in the function and exposure tests. The reference OPC/silica lost its mechanical properties during the 9-month well exposure through extensive HT carbonation, while properties of the CAC-based blends improved over that period. The Modified Cam-Clay (MCC) plasticity parameters of several HT cement formulations were extracted from triaxial and Brazilian tests and verified against the experimental results of function cyclic tests. These parameters can be used in well integrity models to predict field-scale behavior of the cement sheath under geothermal well conditions.

The fifth Industrial revolution (I5.0) prioritizes resilience and sustainability, integrating cognitive cyber-physical systems and advanced technologies to enhance machining processes. Numerous research studies have been conducted to optimize machining operations by identifying and reducing the sources of uncertainty and estimating the optimal cutting parameters. Virtual modeling and Tool Condition Monitoring (TCM) methodologies have been developed to assess the cutting states during machining processes. With a precise estimation of cutting states, the safety margin necessary to deal with the uncertainties can be reduced, resulting in improved process productivity. This paper reviews the recent advances in high-performance machining systems with a focus on the cyber-physical models developed for the cutting operation of difficult-to-cut materials using cemented carbide tools. An overview of the literature and background on the advances in the offline and online process optimization approaches have been presented. Process optimization objectives such as tool life utilization, dynamic stability, enhanced productivity, improved machined part quality, and reduced energy consumption and carbon emissions are independently investigated for the offline and online optimization methods. Addressing the critical objectives and constraints prevalent in industrial applications, the paper explores the challenges and opportunities inherent in developing a robust cyber-physical optimization system

Due to the ongoing global warming on the Earth, permafrost degradation has been extensively taking place, which poses a substantial threat to civil and industrial facilities and infrastructure elements, as well as to the utilization of natural resources in the Arctic and high-latitude regions. In order to prevent the negative consequences of permafrost thawing under the foundations of constructions, various geophysical techniques for monitoring permafrost have been proposed and applied so far: temperature, electrical, seismic and many others. At the same time, non-stationary electromagnetic methods seem to have significant potential and a number of important practical advantages. We propose a cross-borehole exploration system for the highest localization of target objects in the cryolithozone. A novel mathematical apparatus for three-dimensional modeling of transient electromagnetic (TEM) signals by the vector finite element method has been developed. The original combination of the latter, the Sumudu integral transform and artificial neural networks makes it possible to examine spatially heterogeneous objects of the cryolithozone with a high contrast of geoelectric parameters, significantly reducing computational costs. We have studied the sensitivity of the TEM signals to the boundary between thawed and frozen rocks depending on the inter-borehole distance and spatial orientations of the transmitters and receivers. Numerical simulation results of the TEM monitoring of industrial facilities located on permafrost are considered. The formation of a talik has been shown to significantly manifest itself in the measured electromagnetic responses, which enables timely prevention of industrial disasters and environmental catastrophes.

There are different ways to analyse energy absorbance (EA) in the human auditory system. In previous research, we developed a complete finite element model (FEM) of the human auditory system. In this mentioned work, the external auditory canal (EAC), middle ear, and inner ear (spiral cochlea, vestibule, and semi-circular canals) were modelled based on human temporal bone histological sections. Multiple acoustic, structure and fluid-coupled analyses were conducted using the FEM to perform harmonic analyses in the 0.1–10 kHz range. Once the FEM had been validated with published experimental data, the FEM numerical results were used to calculate the EA or energy reflected (ER) by the tympanic membrane. This EA was also measured in clinical audiology tests which were used as a diagnostic parameter. A mathematical approach was developed to calculate the EA and ER, with numerical and experimental results showing adequate correlation up to 1 kHz. Another published FEM had adapted its boundary conditions to replicate experimental results. Here, we recalculated those numerical results by applying the natural boundary conditions of human hearing and found that the results almost totally agreed with our FEM. This boundary problem is frequent and problematic in experimental hearing test protocols: the more invasive they are, the more the results are affected. One of the main objectives of using FEMs is to explore how the experimental test conditions influence the results. Further work will still be required to uncover the relationship between the middle ear structure and EA to clarify how to best use FEMs. Moreover, the FEM boundary conditions must be more representative in future work to ensure their adequate interpretation.

Background: Nowadays, the prevalence of digital device usage has shifted the demands for multifocal intraocular lenses. To accurately capture outcomes, clinical practice must evaluate digital reading performance. We aimed to assess the digital reading performance using a digital device in patients with diffractive multifocal intraocular lenses. Methods: Patients with bilateral diffractive multifocal intraocular lens implantation were included in the study. Monocular and binocular uncorrected and corrected visual acuity was measured using the LogMAR chart and the MNREAD application. Binocular uncorrected defocus curves were obtained using the LogMAR chart at 4m. The reading acuity was measured using the MNREAD application with positive and negative display polarities. The mean digital critical print size (CPS) was recorded using the MNREAD application at 40cm. Results: Our study reported uncorrected distance, intermediate, and near visual acuity were -0.084 ± 0.079, -0.014 ± 0.078, and 0.040 ± 0.081, respectively. The mean reading acuity at three months postoperatively with positive display polarity at 60cm and 40cm was -0.115 ± 0.102 and -0.008 ± 0.083, respectively. The mean digital CPS at three months postoperatively was 0.238 ± 0.100 logMAR. Conclusions: Incorporating digital reading performance measurements provides additional advantages in assessing the effectiveness of bilateral diffractive multifocal intraocular lens implantation.

Biochar is a carbon-rich material that recently received attention due to its increasing agronomical potential. The agricultural utilization of biochar relates to its potential to act in the soil as a soil conditioner, nevertheless, the complex information on the direct dependence of biochar physical properties (texture, particle size) and corresponding leaching and availability of organic molecules (e.g. the polycyclic and heterocyclic organic compounds) and inorganic mineral salts (based on micro– and macroelements) are still not consistent. These aspects were addressed in our study. A multi-elemental analysis (ICP-OES) was used to access the information on the aqueous-extractable and total contents of inorganic macro- and macroelements in used commercial biochar samples (purchased from Sonnenerde GmbH, Novoterrra Sonnenerde GmbH, Biouhel.cz, s.r.o.). Potassium (K) was identified as the major macroelement, responsible for alkaline pH and the conductivity of biochar extract. Our results indicate an indirect relation between the size fraction of biochar and the content of extractable K, sodium (Na), and calcium (Ca) and a direct relation with the contents of phosphorus (P) and magnesium (Mg). As the total determined amounts of inorganic elements were significantly higher compared to aqueous-extractable amounts, we believe it could indicate the potential for repeated release to the surrounding soil. These findings were also confirmed by the analysis of biochar samples obtained after the cultivation (duration of 2 years) in selected representative soil samples from the Czech Republic (Cambisol, Fluvisol, Regosol, Chernozem). Moreover, gas chromatography (GC) coupled with mass spectroscopy (MS) was further used to reveal the concentrations of available polycyclic aromatic and heterocyclic compounds in biochar samples. The detected concentration of these types of organic compounds were far below the certified limits. We believe our in-depth analysis could provide the necessary insight into the description of biochar mineral content, its connection to biochar texture, corresponding physicochemical properties and potential availability to leach nutrients to the soil. These findings could help in further assessment of the potential applications of biochar in modern agriculture as a soil conditioner.

In Korea, the underground silo structure for low- and intermediate-level radioactive waste disposal facilities has been constructed and operated since 2014. Large-scale earthquakes occurred in 2016 and 2017, respectively, in Gyeongju and Pohang areas near the underground silo structures, and interest in the stability of the underground silo increased significantly. In this paper, one-dimensional free field analyses have been carried out before the three-dimensional silo dynamic analyses subjected to earthquake loadings. As an additional study, a new form of finite element equilibrium equation is derived in terms of relative motions, which is essentially the same equation as that expressed in terms of total motions where the base shear force is applied for earthquake load. The accuracy of conventional finite element solutions is evaluated by directly comparing them with closed-form solutions by frequency domain analysis such as SHAKE91.

Transcutaneous nerve stimulation has several neuromodulatory applications, including pain management, sensory restoration, and motor recovery. Transcutaneous stimulation delivered via electrode arrays offers ease of use and reconfigurability through non-invasive means. Also, employing electrode arrays allows regulation of the permeated electric fields for greater control over the stimulation performance. Field shaping involves the regulation of permeated electric fields and is a well-established practice for deep brain stimulation; however, its applicability to peripheral nerve stimulation still needs exploration. Adopting such techniques can help to overcome current limitations with transcutaneous stimulation, like poor targetability, early onset of fatigue, and perceived discomfort. This article provides a perspective on the applicability of field-shaping techniques in improving the overall stimulation outcome.

The study delves into the critical examination of the Size of Loss distribution patterns in the context of auto insurance during pre- and post-pandemics, emphasizing their profound influence on insurance pricing and regulatory frameworks. Through a comprehensive analysis of the historical Size of Loss data, insurers and regulators gain essential insights into the probabilities and magnitudes of insurance claims, informing the determination of precise insurance premiums and the management of case reserving. This approach aids in fostering fair competition, ensuring equitable premium rates, and preventing discriminatory pricing practices, thereby promoting a balanced insurance landscape. The research further investigates the transformative impact of the COVID-19 pandemic on these Size of Loss patterns, given the substantial shifts in driving behaviors and risk landscapes. Also, the research contributes to the literature by addressing the need for more studies focusing on the implications of the COVID-19 pandemic on pre- and post-pandemic auto insurance loss patterns, thus offering a holistic perspective encompassing both insurance pricing and regulatory dimensions.

This study aimed to investigate the interactions between corn particle size (PS) and conditioning temperature (CT) on the performance, carcass traits, intestinal morphology, and immune responses in broilers fed a corn-soybean meal-based diet. A total of 360, one-day-old male broiler chicks (Ross 308) were randomly allocated into six dietary treatments in a 2×3 factorial arrangement, consisting of two corn PS (finely ground with geometric mean diameter (GMD) of 357 µm (PSF) vs. coarsely ground corn with GMD of 737 µm (PSC), and three CT [unconditioned (CTU), conditioned at 75◦C (CT75) and 90◦C (CT90)]. Birds accommodated in 30 pens with five replicates and 12 chicks per each. There was no interaction between corn PS and CT on growth performance and immune response of broilers at any growth phases. However, during the starter (0-10d) period, the average daily weight gain (ADWG) and feed conversion ratio (FCR) of PSF-fed birds were significantly improved compared to those fed PSC (P<0.05). During the starter (0-10d) and grower (11-24d) periods, increasing the conditioning temperature of corn increased the ADWG, while in the starter phase only the CT75 caused a lower FCR (P<0.05). Broilers fed PSF corn showed lowest FCR during the finisher (25-42d) period compared to those fed PSC (P<0.05). Conditioning corn at 75ºC reduced FCR during the finisher (25-42d) period compared to the birds fed CTU and CT90 corn (P<0.05). In whole experimental periods (1-42d), PSF and CT75 treatment increased the ADWG compared to the PSC and CTU (P<0.05). The CT75 treatment improved primary total anti-sheep red blood cell (SRBCs) titer (IgT) and IgM and secondary IgT and IgG responses compared to the other experimental groups (CTU and CT90) (P<0.05). No significant PS × CT interaction was found on Newcastle disease (ND) antibody titer of broiler chickens (P>0.05). Feeding CT75 corn reduced duodenum and jejunum relative length compared to the birds fed diets containing CTU corn. Significant PS×CT interactions (P<0.05) were observed for villus height, villus height to crypt depth, crypt depth, muscle thickness, and absorption surface area of jejunum. The highest carcass yield observed in PSF-CT75-group (P<0.05). In conclusion, the use of finely ground corn (PSF) conditioned at 75℃ (CT75) was beneficial to growth performance, development of the digestive tract, jejunum histomorphometry and the immune responses of broilers.

The influence of applied loads on free vibrations analysis of plates and shells panels made of functionally graded materials is analyzed in the present work. Formulations for the static analysis considering geometrically nonlinear behavior, as well as linear buckling and free vibrations analyses are considered. The calculation of the through-thickness stress distribution is also performed. A finite element model based on a higher order shear deformation theory and using a non-conforming triangular flat plate/shell element with 3 nodes, and 8 degrees of freedom per node is used in the numerical implementation. The results obtained with this numerical model are presented, discussed, and compared with alternative solutions published by other authors in some benchmark applications.

This paper presents a numerical study on the laser shock wave propagation in a 3D woven CFRP material by means of detailed and homogenized FE models. The aim of the study is to numerically characterize the shock wave response of the 3D woven CFRP in terms of back face velocity profiles and the induced damage and to investigate whether the detailed FE models could be replaced by homogenized FE models. The 3D woven geometry was designed using the TexGen software, while the numerical analyses were executed using the LS-Dyna explicit FE software. A high-strain rate behavior was considered for the matrix. The fiber bundles in the detailed models were modeled as a high fiber content unidirectional composite laminate, with its mechanical properties calculated by micromechanical equations. Both for the fiber bundles of the detailed model and the homogenized models a progressive damage material model was applied. The results of the detailed model reveal a considerable effect of material’s architecture on the shock wave propagation and the sensitivity of the back face velocity profile to the spot location. Consequently, the homogenized model is not capable of accurately simulating the shock wave response of the 3D woven composite. Moreover, the detailed predicts with high accuracy matrix cracking in the resin-rich areas and in the bundles as well as fiber failure. On the contrary, the homogenized model predicts matrix cracking at the same areas and no fiber failure.

The Internet of Things (IoT) is a technological paradigm that has gained significant momentum that last decade and, among others, enables the development of intelligent and interoperable device networks. In this respect, it has triggered the creation and evolution of VANETs (Vehicular Ad Hoc Networks), which are initially implemented in order to guarantee the safety of the drivers and the avoidance of traffic accidents. The drawback is that this fast evolution flags serious concerns as far as the privacy of users is concerned, while the population of attackers or entities that try to eavesdrop and intercept information has significantly increased. This imposes a serious risk for drivers moving across a Smart City. The research presented in this paper aims to evaluate privacy protection mechanisms in VANET environments, based on their efficiency and security level ensured, considering the fact that VANETs provide limited resources to users/drivers. Moreover, the usage of the elliptic curve cryptography in reduced resources environments is discussed. Finally, this paper compares the performance of three cryptographic algorithms, i.e., Elliptic Curve Cryptography (ECC), Hyperelliptic Curve Cryptography genus 2 (HECC-2) and HECC genus 3 (HECC-3), employed for an efficient authentication and safe message transmission mechanism in VANETs, targeting to extract conclusions related to the implementation of each cryptographic scheme in this specific application area.

Microvascular self-healing composite materials have significant potential for application and their mechanical properties need in-depth investigation. In this paper, tensile and compressive properties of woven fabric carbon fiber reinforced polymers (CFRP) laminates containing three-dimensional microvascular channels were investigated experimentally. Several detailed finite element (FE) models were established to simulate the mechanical behavior of the laminate and the effectiveness of different models were examined. The damage propagation process of the microvascular laminates and the influence of microvascular parameters were studied by the validated models. The results show that microvascular channels arranged along the thickness direction (z-direction) of the laminates are critical locations under the loads. The channels have minimal effect on the stiffness of the laminates but causing a certain reduction in strength, which varies approximately linearly with the z-direction channel diameter within its common design range of 0.1~1mm. It is necessary to consider the resin-rich region formed around microvascular channels in the warp and weft fiber yarns of the woven fabric composite when establishing the FE model. And the layers in model should be assigned with equivalent unidirectional ply material in order to calculate the mechanical properties of laminates correctly.

We extend Ziv and Lempel's model of finite-state encoders to the realm of lossy compression of individual sequences. In particular, the model of the encoder includes a finite-state reconstruction codebook followed by an information lossless finite-state encoder that compresses the reconstruction codeword with no additional distortion. We first derive two different lower bounds to the compression ratio that depend on the number of states of the lossless encoder. Both bounds are asymptotically achievable by conceptually simple coding schemes. We then show that when the number of states of the lossless encoder is large enough in terms of the reconstruction block-length, the performance can be improved, sometimes significantly so. In particular, the improved performance is achievable using a random-coding ensemble that is universal, not only in terms of the source sequence, but also in terms of the distortion measure.

This study investigates the elastic buckling behaviour of skew Functionally Graded Material (FGM) thin plates featuring a circular opening. FGM materials, known for their unique property gradients, have gained prominence in structural engineering due to their mechanical performance and durability. Including a circular opening introduces a critical geometric consideration, influencing the structural stability and load-carrying capacity of FGM plates. The study examines the effects of the skew angle, plate’s aspect ratio, opening position, and size on the critical buckling load, normalized buckling load, and various buckling failure modes through computer modelling and finite element analysis. The results offer valuable insights into the interplay between material heterogeneity, geometric configuration, and structural stability. For instance, the critical buckling load increases by 29%, 82%, and 194% with the increment of skew angle from 0° to 30°, 45°, and 60°, respectively. Moreover, as the opening shifts from the plate’s edge closer to the center, the critical buckling load decreases by 26%. This research contributes to the advancement of understanding FGM thin plates’ behaviour under skew loading conditions, with implications for the design and optimization of innovative structures. The findings presented provide a foundation for further exploration of advanced composite materials and their applications in structural engineering.

Digital twin, an innovative technology propelled by data and models, plays a seminal role in the digital transformation and intelligent upgrade of ships. This study introduces a digital twin methodology for real-time monitoring of ship structure deformation fields, based on finite discrete strain data, and a visualization tool framework is developed using virtual reality technology. First, the inverse Finite Element Method (iFEM) is employed to derive the deformation field of the ship structure in real time via sensor strain data. Secondly, the deformation field data obtained based on the iFEM algorithm is converted into general visualization data conducive to interpretation within VR applications. Lastly, a digital twin software tool is built to enable synchronous response and interaction between the virtual scene and the physical scene, directly superposing particular virtual objects (data acquired by sensors, CAD virtual models, and deformation field cloud images) onto the physical scene in real-time. The digital twin tool embodies a virtual reality visualization system framework integrating physical data measurement, reconstruction, analysis, expression, storage, rendering and interaction of deformation field data. Through practical application, the flexibility, effectiveness and compatibility of the developed prototype tool are verified. According to the results, the system can enhance the efficiency of scientific communication, model validation, and interdisciplinary sharing during the analysis and evaluation of mechanical properties of ship structures.

Phytoplankton guilds are commonly characterised by dominance effects, while the main contribution to biological diversity is given by rare species. Here, we analysed the influence of rare species on taxonomic and functional diversity, described by taxa richness and composition, cell size and size abundance relationships in phytoplankton guilds. We explore these relationships at global and regional scales by analysing phytoplankton guilds from five biogeographical regions: Northern Atlantic Ocean (Scotland), South-Western Atlantic Ocean (Brazil), South-Western Pacific Ocean (Australia), Indo-Pacific Ocean (Maldives) and Mediterranean Sea (Greece and Turkey). We have comparatively analysed the phytoplankton taxonomic diversity of the whole dataset and with the datasets obtained by progressively subtracting taxa occurring in the last 1%, 5%, 10% and 25% of both numerical abundance and overall biomass. Globally 306 taxa were identified across five ecoregions with only 27 taxa accounting for the 75% of overall numerical abundance and biomass; almost the 50% of taxa were lost on every step. The removal of 1% most rare taxa significantly affected the phytoplankton size-abundance relationships and body-size structure, strongly impacting on small taxa. The progressive removal of additional rare taxa did not further affect phytoplankton size-abundance relationships and size structure.

Lightweight component design is effectively achievable through the sandwich structures, many past research studies in the aerospace and racing sectors (since 1920s) has proven it. To extend their application into automotive and other transport industries, the manufacturing cycle times must be reduced. This can be achieved by thermoplastic sandwich materials of continuous fibre-reinforced thermoplastic (CFRTP) cover layers and thermoplastic honeycomb cores. To widespread the application of flat thermoplastic-based sandwich panels into complex parts, a novel forming technology was developed by the Fraunhofer Institute of Microstructure of Materials and Systems (IMWS). For an increase in reproducibility of the sandwich component production and a decrease in manufacturing defects, numerical modelling methods and experimental validation are needed. The finite element (FE) modelling of this thermoforming process is a thermo-mechanical assignment with all three: material, geometry, and boundary non-linearities. In the scope of this work, the material behavior of different sandwich components (cover layers, honeycomb core, interface) under thermo-mechanical loads is characterized in detail, and a complex numerical model is developed to describe the thermoforming process of thermoplastic-based sandwich laminate. The critical forming condition like wrinkling that occurs due to friction in a sandwich or poor intra-ply shear in cross-ply studied, validated, and optimized. A thermoplastic sandwich made of polypropylene (PP) honeycomb core and polypropylene glass fibre (PP/GF) cross-ply as cover layers was used for this study, and numerical modelling was executed in LS-DYNA software.

The object of study is a transversely bent triangular plate made of orthotropic material fixed along the edges of the plate under the action of a uniformly distributed load. Fourth-order differential equilibrium equations with variable orthotropy parameters were used. The equations were approximated by finite differences for a grid of scalene triangles. This type of mesh accurately describes the boundary contour of the triangular-shaped plates. The boundary conditions for the mesh consider the orthotropy of the plate material. Seven standard finite-difference equations have been developed considering the boundary conditions along the three edges of the plate and the presence of three angles of an irregularly shaped triangle. A finite difference matrix is obtained. The matrix structure makes calculating a triangular plate at different base angles possible. The boundary conditions were varied in the form of rigid or hinged support of triangular plates. The calculation method considers the orthotropic parameters of the material in two mutually perpendicular planes. The adaptation of the numerical method to the calculation of orthotropic plates of arbitrary shape is described. Relationships are given for determining the rigidity characteristics of orthotropic materials. An algorithm for simple engineering calculation of triangular orthotropic plates is proposed, which makes it possible to perform accurate calculations in variant design.

One of the most widely available and extensively produced varieties of industrial hemp, which generates a substantial amount of consumer-increasing waste in the form of hemp cellulose. In this study, recycling with a compressed and high-speed method that combines crushing and alkali treatment effectively converts leftover hemp fiber into ultrafine powder. SEM (Scanning Electron Microscopy), AFM (Atomic Force Microscope), FTIR (Fourier-transform Infrared Spectroscopy), and XRD (X-ray Diffraction) examined the original morphology of hemp fiber treated with alkali, fiber heated to 200 ℃, and crushed powder. Particle size, crystallinity, fiber surface, and strength increased and decreased. It became apparent that fiber strength decreased and fiber roughness significantly increased after alkali treatment. Fiber increased significantly, and crystallinity decreased after crushing. It was simple and effective for converting the leftover hemp fiber into micron-sized powder. In about 3 to 5 minutes, approximately 1 kg of dry ultrafine powder with a particle size of 10.44 μm was produced. This production method will significantly enhance future industrial applications of waste hemp fiber.

This paper proposes an analytical model of the double-stator spoke-type permanent-magnet vernier machine (DSSTVM) using the subdomain model (SDM), which can be used to calculate the mag-netic field distribution and corresponding electromagnetic parameters of the DSSTVM. The whole field domain is divided into several subdomains according to the magnetic characteristics of each region, within which Laplace's and Poisson's equations are solved accordingly in terms of magnetic vector potential (MVP). Then, the magnetic flux density distribution, back electromotive force (EMF), and electromagnetic torque of the DSSTVM can be obtained correspondingly. Ultimately, finite element analysis (FEA) is adopted to validate the proposed analytical model's effectiveness for quickly predicting the no-load and on-load performances of the DSSTVM.

Chromosome segregation in female germ cells and early embryonic blastomeres is known to be highly prone to errors. The resulting aneuploidy is therefore the most frequent reason for termination of early development and embryo loss in mammals. And when compatible with embryonic and foetal development, aneuploidy leads into severe developmental disorders. The main surveillance mechanism, essential for protection of cells against aneuploidy, is the Spindle Assembly Checkpoint (SAC). And although all eukaryotic cells are perhaps able to mount SAC response, it is not clear, whether this pathway is active in all cell types, including blastomeres of early embryos. In this review, we will summarize and discuss the published literature with regards to mechanisms controlling chromosome segregation in early embryos. Our conclusion is that early embryos show limited capabilities to react to chromosome segregation defects, which might, at least partially, explain the widespread problem of aneuploidy during early development.

The extreme environmental issues and the resulting needs to save energy have turned the attention to electrification of energy applications. One of the key components involved in energy efficiency improvements is the appropriate conception and manufacturing of electric machines. This paper overviews the electromagnetic analysis governing the behavior of permanent magnets that enabled substantial efficiency gains in recent electric machine developments. Particular emphasis is given to model the properties and losses developed in permanent magnets in the emerging high speed applications. In addition, the investigation of properties and harmonic losses related to ferromagnetic materials constituting the machine magnetic circuits are equally analyzed and discussed. The experimental validation of the implemented methodologies and developed models with respect to the obtained precision is reported. The introduction of mixed numerical techniques based on the finite element method intended to appropriately represent the different physical phenomena encountered is outlined and discussed. Finally, fast and accurate simulation techniques including aggregated lumped parameter models considering harmonic losses associated with inverter supplies are commented.

Cavitation resulting from underwater explosions in compressible multiphase or multicomp-onent flows presents significant challenges due to the dynamic nature of shock-cavitation-structure interactions, as well as the complex and discontinuous nature of the involved interfaces. Achieving accurate resolution of interfaces between different phases or components, in the presence of shocks, cavitating regions, and structural interactions, is crucial for modeling such problems. Furthermore, pressure convergence in simulations involving shock-cavitation-structure interactions requires accurate algorithms. In this research paper, we employ the diffuse interface method, also known as the interface capturing scheme, to investigate cavitation in various underwater explosion test cases near different surfaces; free surface and a rigid surface. The simulations are conducted using the Unstructured Compressible Navier-Stokes (UCNS3D) finite volume framework employing central-weighted essentially non-oscillatory (CWENO) reconstruction schemes, utilising the five-equation diffuse interface family of methods. Quantitative comparisons are made between the performance of both models. Additionally, we examine the effects of cavitation as a secondary loading source on structures, and evaluate the ability of the CWENO schemes to accurately capture and resolve material interfaces between fluids with minimal numerical dissipation or smearing. The results are compared with existing high-order methods and experimental data, where possible, to demonstrate the robustness of the CWENO schemes in simulating cavitation bubble dynamics, as well as their limitations within the current implementation of interface capturing.

This study empirically analyzes how R&D expenditures affect firm value using a regression model for listed firms in Shandong Province, China. The dependent variable is measured by To-bin Q, which measures firm value, and the experimental variable among the independent varia-bles is R&D expenditure. In addition, financial leverage and firm size, which have been found to have a significant impact on firm value in previous studies, were selected as control variables. The study sample consisted of 554 data points analyzed over a nine-year period from 2010 to 2018. Without controlling for variables that affect firm value, the correlation analysis shows that R&D expenditures of listed firms in Shandong Province, China have a significant positive impact on firm value at the 1% level. For a more precise analysis, we ran a multivariate regression analysis controlling for other variables that affect firm value and found that R&D expenditure has a significant positive impact on firm value at the 1% level. These findings suggest that man-agers of listed companies in Shandong Province, China, need to actively engage in R&D activi-ties to increase firm value. Companies in Shandong Province, China, are currently experiencing very strong growth, and this study, which shows that R&D is the key to increasing the value of these companies, can help companies in Shandong formulate their business strategies.

Recent studies have shown that the mechanical properties of bioinspired periodic composite materials can be strongly influenced by finite deformation effects, leading to highly nonlinear static and dynamic behaviors at multiple length scales. For instance, in porous periodic nacre-like microstructures, microscopic and macroscopic instabilities may occur for a given uniaxial loading process and, as a consequence, wave attenuation properties may evolve as a function of the microstructural evolution, giving it the designation of metamaterials. The numerical outcomes provide new opportunities to design bioinspired soft composite metamaterials characterized by high deformability and enhanced elastic wave attenuation capabilities given by the insertion of voids and lead cores.

Starting from the analysis of the lack of positivity of the Cattaneo heat equation, the article addresses the thermodynamic relevance of the positivity constraint in irreversible thermodynamics, than is at least as important as the entropic constraints. The fulfillment of this condition in hyperbolic models leads to the parametrization of the concentration fields with respect to internal variables associated with the microscopic dynamics. Using Brownian motion theory as a landmarking example for deriving macroscopic transport equations from the equations of motion at the particle/molecular level, we discuss two typical problems involving hydrodynamic interactions at microscale: surface chemical reactions at a solid interface of a diffusing reactant, and mass-balance equations in a complex viscoelastic fluid, in which the physics of the interaction leads either to the overcome the parabolic diffusion model or to consider the parametrization of the concentration with respect to the degrees of freedom associated with the relaxation dynamics of the solvent fluid.

The article presents a technology for producing nitrogen-containing nanoporous biocarbon with high degree of elemental composition homogeneity, confirmed by electron spectroscopy. The research explores the relationship among the electronic characteristics of supramolecular nanoporous carbon, its porous structure, and the capacitance at its interface with the electrolyte. The obtained biocarbon is characterized by micro and mesopores, as evidenced by the results of studies by the method of nitrogen adsorption/desorption. The specific area of the available porous surface was found to be 1247 m2/g. Comparing this result with the data of small-angle X-ray scattering, we conclude that micropores are open while mesopores remain closed. This material was found to have a saturation magnetization σs of 1.4 A∙m2∙kg-1 and a coercive force Hc of 10 kA/m. The impedance studies of electrochemical cells of supercapacitors made of the experimental biocarbon were carried out. Equivalent electrical circuits of the studied electrochemical processes were constructed and characterized.

New or in-service truss bridges, with or without upper bracing systems, may display instability phenomena such as general lateral torsional buckling of the upper chord. The buckling of structural elements, particularly in the case of steel bridges, can be associated with the risk of collapse or temporary/permanent withdrawal from service. Buckling poses a significant danger as it often occurs at lower load values compared to those considered during the design phase. Additionally, this phenomenon can manifest suddenly, without prior warning, rendering intervention for its prevention impossible or futile. In contemporary times, most research and design calculation software offer the capability to establish preliminary values for buckling loads, even for highly intricate structures. This is typically achieved through linear eigenvalue buckling analyses, often followed by significantly more complex large displacement nonlinear analyses. However, interpreting the results for complex bridge structures can be challenging, and their accuracy is difficult to ascertain. Consequently, the objective of this paper is to introduce an original method for a more straightforward estimation of the buckling load of the upper chord in steel truss bridges. The method utilizes the theory of beams on an elastic foundation. The buckling load of the upper chord was determined using both the finite element method and the proposed methodology, yielding highly consistent results.

Thermoplastic composites are continuously replacing thermosetting composites in lightweight structures. However, the accomplished work on the fatigue behavior of thermoplastics is quite limited. In the present work, we propose a numerical modeling approach for simulating fatigue delamination growth and predicting the residual tensile strength of quasi-isotropic TC 1225 LM PAEK thermoplastic coupons. The approach is supported and validated by tension and fatigue (non-interrupted and interrupted) tests. Fatigue delamination growth is simulated using a mixed-mode fatigue crack growth model, which is based on the cohesive zone modeling method. All interfaces between the thermoplastic plies were modelled using cohesive elements. Quasi-static tension analyses on pristine and fatigued coupons were performed using a progressive damage model implementing a set of Hashin-type strain-based failure criteria and a damage mechanics-based material property degradation module. Using the fatigue model, delamination growth was predicted as a function of number of cycles at all interfaces. The results agree well with C-scan images taken on fatigued coupons during interruptions of fatigue tests. An unequal and unsymmetric delamination growth was predicted due to the quasi-isotropic lay-up. Moreover, the combined models capture the decrease in the residual tensile strength of the coupons. In the quasi-static tension analysis of the fatigued coupons, the driving failure mechanisms are the fast propagation of the pre-existing delamination and the severe matrix cracking.

This article introduces a new physically based Lyapunov function difinition, which can be used as acoustic energy for finite amplitude pressure oscillations in reacting systems especially in combustion chambers. Reacting flow is seen as an open, non-equilibrium (parameters are distributed unevenly locally) thermodynamic system. This Lyapunov function is defined as the maximum mechanical work, which could be extracted by a heat engine from studied system, if this system would be disconnected from inlet and outlet and from any other surrounding environment, and the engine could transfer to the surrounding environment only mechanical work.

To follow the growth and development of each tree (N = 1200) Pinus sylvestris L., var. Negorelskaya starting from the seed and continuing at the juvenile (or even generative) stage is the goal of an ambitious project to create a plant passport if possible. Five datasets of replenished empirical (tab-ular and file) and systematic data reflect the early results of a unique ongoing experiment conducted with families moved along a climatic gradient from the collection area (1731 degree days, 722 mm) to the experimental area (2326 degree days; 786 mm). Datasets of morphometric, VIS-spectrometric, and germination seed data, combined with the first results of biometric data (including the Dickson quality index) of seedlings produced from these seeds, will allow scientists in the future to conduct correlation and other statistical analysis, or train a neural network to determine the presence of connections between a seed and a plant. These data contribute to the early non-destructive diag-nosis and grading of seeds according to VIS-spectrometric properties. This dataset structure can complement the FLR-Library. In the future, by tracing seedlings in their early growth (for example, over three growing seasons at the site being restored), it will be possible to determine the degree of intensification of FRM production depending on the initial properties of the seed.

‘Inner mitochondrial membrane peptidase 2 like’ (IMMP2L) is a nuclear encoded mitochondrial peptidase that has been conserved through evolutionary history as has its target enzyme ‘mitochondrial glycerol phosphate dehydrogenase 2’ (GPD2). IMMP2L is known to cleave the mitochondrial transit peptide from GPD2 and another nuclear encoded mitochondrial respiratory related protein cytochrome C1 (CYC1). However, it is not known whether IMMP2L peptidase activates or alters the activity or respiratory related functions of GPD2 or CYC1. Previous investigations found compelling evidence of behavioural change in the Immp2lKD-/- KO mouse and in this study EchoMRI analysis found that many organs of the Immp2lKD-/- KO mouse were smaller and that the KO mouse had significantly less lean mass and overall body weight compared with wildtype littermates (p&lt;0.05). Moreover, all of the organs analysed from the Immp2lKD-/- KO had lower relative levels of mitochondrial reactive oxygen species (mitoROS). The kidneys of the Immp2lKD-/- KO mouse displayed the greatest decrease in mitoROS levels that were over 50% less compared with wildtype litter mates. Mitochondrial respiration was also lower in the kidney of the Immp2lKD-/- KO mouse compared with other tissues when using succinate as the respiratory substrate, whereas respiration was similar to wildtype when glutamate was used as substrate. When glycerol-3-phosphate (G3P) was used as the substrate for Gpd2 we observed ~20% and ~7% respective decreases in respiration in female and male Immp2lKD-/- KO mice over time. Together these findings suggest that the respiratory related functions of mGpd2 and Cyc1 have been compromised to different degrees in different tissues in the Immp2lKD-/- KO mouse. Structural analyses using AlphaFold2-Multimer further predicted that the interaction between Cyc1 and mitochondrial encoded cytochrome b (Cyb) in Complex III had been altered as had the homodimeric structure of the mGpd2 enzyme within the inner mitochondrial membrane of the Immp2lKD-/- KO mouse. mGpd2 functions as an integral component of the glycerol phosphate shuttle (GPS) which positively regulates both mitochondrial respiration and glycolysis. Interestingly, we found that nonmitochondrial respiration (NMR) was also dramatically lowered in the Immp2lKD-/- KO mouse. Primary mouse embryonic fibroblast (MEF) cell lines derived from the Immp2lKD-/- KO mouse displayed a ~27% decrease in total respiration comprised of a ~50% decrease in NMR and a ~12% decrease in total mitochondrial respiration where the latter was consistent with the decreases in substrate specific mitochondrial respiration reported here. This study is the first to report the role of Immp2l in enhancing Gpd2 structure and function, mitochondrial respiration, nonmitochondrial respiration, organ size and homeostasis.

This work aims at improving surface integrity and LCF life of machined Inconel 718. The correlation between the LCF life of Inconel 718 and various states of machined surface integrity is explored. In this paper, the surface integrity of Inconel 718 specimens is enhanced by low plasticity burnishing (LPB). The LCF life with different surface integrity specimens is predicted by micro-macro finite element method (FEM). Firstly, the LCF specimens with different surface integrity are machined by turning (turned specimen), polishing (matrix specimen) and LPB process (LPBed specimen). Secondly, the LCF experiment is carried out to reveal the effect of surface integrity on LCF life. Finally, the LCF micro-macro FEM model is proposed to predict the LCF of machined Inconel 718 specimens. The representative volume element (RVE) model is established based on the measured surface integrity and microstructure of Inconel 718 specimens. The effect of surface integrity on LCF life is transformed to equivalent load. The micro-macro FEM model combined with Tanaka-Mura dislocation crack initiation theory and extended finite element method (XFEM) is applied to predict the LCF life the machined specimens. The study results show that the LCF life of LPBed specimens can be improved by 90.5% and 36.1% compared with that of turned specimens and polished matrix specimens, respectively. The errors between FEM prediction results and experimental results are 13.1%, 9.2% and 12.2%, respectively. The proposed micro-macro FEM model could be utilized to predict the LCF life of Inconel 718 with different surface integrity, and further to apply the LCF life prediction in industry.

Aedes aegypti is the main vector of various arboviruses including dengue, yellow fever, Zika and chikungunya virus. This mosquito species originated in Africa but has a wide range of distribution, colonising various ecological zones. The transmission dynamics of arboviruses depends on environmental factors, but also on mosquito life history traits including development time, fecundity, and longevity. The objective of the current study was to assess the Aedes aegypti immature development time, adult longevity, fecundity and body variation from different sampling localities. Aedes aegypti mosquitoes were collected as eggs from different geographical zones and cohorts of mosquitoes were reared in standardized laboratory conditions to assess the life history traits parameters. Emerged adults were discriminated into morphotypes according to the density of white scales on the first abdominal tergite. The means of fecundity, longevity, development time and body size were assessed, and linear models were fitted to the traits parameters to assess the effects of other covariables. Average Aedes aegypti development time was estimated to 7.35 days; 7.40 days; 6.98 days and 7.40 days respectively for Dori, 1200 logements, Bobo-Dioulasso and Toudweogo. The fecundity did not vary across study sites and was not associated with the body size. The longevity varied according to the study sites with the mosquitoes from Bobo-Dioulasso having the longest longevity while the shortest longevity was found at Dori. Fed mosquitoes had longer longevity compared to unfed ones. Morphological identification showed that Aedes aegypti aegypti-like mosquitoes were more predominant than Aedes aegypti formosus-like mosquitoes in all the study sites, suggesting the predominance of Aedes aegypti in the urban environment. Our data suggest that the geographical origin of Aedes aegypti mosquitoes in Burkina Faso has a little effect on its life history traits.