A technology for obtaining nanosized aluminum nitride powder by plasma-chemical synthesis is presented. Nitrogen gas (N2), melamine (C3H6N6) and ammonia (NH3) were used as a source of nitrogen. Aluminum powder of different fractions was used as a source of aluminum. The influence of the nitrogen source, the height of the injector, and the input power of the plasma equipment on the synthesized aluminum nitride powder is shown. The resulting aluminum nitride powder has a size d90=60 nm. The parameters of aluminum nitride synthesis did not in any way affect the granulometric composition of the synthesized powder materials. It was found that, due to the high binding energy, the nitrogen molecule (N2) reacts poorly with aluminum powder particles, as a result a mixture of nitrogen and ammonia gases was used in a ratio of 70/30 (mol.%) for aluminum nitride synthesis.

This article addresses the problem of formation control of a quadrotor and one (or more) marine vehicles operating at the surface of the water with the end goal of encircling the boundary of a chemical spill, enabling such vehicles to carry and release chemical dispersants used during ocean cleanup missions to break-up oil molecules. Firstly, the mathematical models of the Medusa class of marine robots and quadrotor aircrafts are introduced, followed by the design of single vehicle motion controllers that allow these vehicles to follow a parameterized path individually using Lyapunov based techniques. At a second stage, a distributed controller using event triggered communications is introduced, enabling the vehicles to perform cooperative path following missions according to a pre-defined geometric formation. In the next step, a real time path planning algorithm is developed that makes use of a camera sensor, installed on-board the quadrotor. This sensor enables the detection in the image of which pixels encode parts of a chemical spill boundary and use them to generate and update in real time a set of smooth B-spline based paths for all the vehicles to follow cooperatively. The performance of the complete system is evaluated by resorting to 3-D simulation software, making it possible to simulate visually a chemical spill. Results from real water trials are also provided for parts of the system, where two Medusa vehicles are required to perform a static lawn-mowing path following mission cooperatively at the surface of the water.

Peptide-based drugs are promising anticancer candidates due to their biocompatibility, and low toxicity. Particularly, tumor homing peptides (THPs) have the ability to bind specifically to can-cer cells receptors and tumor vasculature. Despite their potential to develop antitumor drugs, there are few available prediction tools to assist the discovery of new THPs. Two webservers based on machine learning models are currently active, the TumorHPD (https://webs.iiitd.edu.in/raghava/tumorhpd) and the THPep (http://codes.bio/thpep), and more recently the SCMTHP (SCMTHP (pmlabstack.pythonanywhere.com), based on scoring card method. Herein, a novel method based on network science and similarity searching implemented in the starPep toolbox (http://mobiosd-hub.com/starpep/) is presented for THPs discovery. The approach leverages from exploring the structural space of THPs with Chemical Space Networks (CSNs) and from applying centrality measures to identify the most relevant and non-redundant THPs sequences within the CSN. Such THPs were considered as queries (Qs) for multi-query similarity searches that applies a group fusion (MAX-SIM rule) model. The resulting multi-query similarity searching models (SSMs) were validated with three benchmarking datasets of THPs/non-THPs. Predictions achieved accuracies ranged from 92.64 to 99.18% and Matthews Correlation Coefficients between 0.894-0.98, outperforming state-of-the-art predictors. The best model was applied to repurpose AMPs from the starPep database as THPs, which were subse-quently optimized for the TH activity. Finally, 54 promising THP leads were discovered, and their sequences were analyzed to encounter novel motifs. These results demonstrate the potential of CSNs and multi-query similarity searching for a rapid and accurate identification of THPs.

The conversion of methane into chemicals is of interest to achieve a decarbonized future. Fuel cells are electrochemical devices commonly used to obtain electrical energy, but can be utilized either for chemicals production or both energy and chemicals cogeneration. In this work, the partial oxidation of methane in fuel cells for electricity generation and valuable chemicals production at the same time is reviewed. For this purpose, different types of methane-fed fuel cells, both low temperature fuel cells, such as PEMFCs and AAEMFCs, and high temperature fuel cells, such as SOFCs, have been used. Also if few works have been devoted to this topic, the promising results drive the development of fuel cells using methane as the source for the cogeneration of power and valuable chemicals.

The Covid‐19 pandemic, evolving needs of students & mentors, and the drive for global educational equality are collectively shifting how courses are packaged/distributed, ushering a more holistic approach and blending of fields. We recently created interdisciplinary courses in chemical biology aimed at massive open online and small private levels. These courses cover biology, chemistry, & physics, and concepts underlying modern chemical‐biology tools. We discuss what we learned while creating/overseeing these courses: content optimization and maintaining material freshness while fostering a stimulating learning environment. We outline mechanisms that help sustain student attention throughout rapidly‐moving courses, how to integrate adaptability to students’ needs in the short & long term, and speculate how we could have improved. We believe this will be an important guide for anyone wanting to develop online learning formats ideal for nurturing interdisciplinary scientists of tomorrow.

Light-addressable potentiometric sensor (LAPS) is an electrochemical sensor based on the field-effect principle of semiconductor. It is able to sense the change of Nernst potential on the sensor surface, and the measuring area can be controlled by the illumination. Due to the unique light-addressable ability of LAPS, the chemical imaging system constructed with LAPS can realize the two-dimensional image distribution detection of chemical/biomass. In this paper, the advantages of LAPS as sensing unit of microelectrochemical analysis system are summarized. Then, the greatest development of LAPS analysis system is explained and discussed. Especially, this paper focused on the research of ion diffusion, enzymatic reaction, microbial metabolism and droplet microfluidics by using LAPS analysis system. Finally, the development trends and prospects of LAPS analysis system are illustrated.

With heat treatments to control drywood termites (Blattodea: Kalotermitidae), the presence of heat sinks causes heat to be distributed unevenly throughout the treatment areas. Drywood termites may move to galleries in heat sink areas to avoid exposure to lethal temperatures. Our studies were conducted in Crytotermes brevis-infested condominiums in Honolulu, Hawaii to reflect real-world condominium scenarios; either a standard heat treatment performed by a heat remediation company or an improved heat treatment was used. For improved treatments, heated air was directed into the toe-kick voids of C. brevis infested cabinets to reduce heat sink effects and increase the heat penetration into these difficult-to-heat areas. Eight thermistor sensors placed inside toe-kick voids, treatment zone, embedded inside cabinets’ sidewalls, and in a wooden cube recorded target temperatures of above 46 °C or 50 °C for 120 minutes. A pretreatment and follow-up inspections were performed at 6 months posttreatment to monitor termite inactivity using visual observations and by recording the numbers of spiked peaks on a microwave technology termite detection device (Termatrac). In improved treatment condominiums, significantly higher numbers of spiked peaks were recorded at pretreatment as compared to 6 months posttreatment. Efficacious heat treatment protocols using the improved methods are proposed.

The chemical graph theory is a subfield of mathematical chemistry which applies classic graph theory to chemical entities and phenomena. Chemical graphs are main data structures to represent chemical structures in cheminformatics. Computable properties of graphs lay the foundation for (quantitative) structure activity and structure property predictions - a core discipline of cheminformatics. It has a historic relevance for natural sciences, such as chemistry, biochemistry and biology, and is in the heart of modern disciplines, such as cheminformatics and bioinformatics. This review first covers the history of chemical graph theory, then provides an overview of its various techniques and applications for CASE, and finally summarises modern tools using chemical graph theory for CASE.

For every three people on the planet there is approximately two Tonne (Te) of available plastic waste. We show that carbon recovery from polystyrene (PS) plastic is enhanced by the co-addition to solvents to grow carbon nanotubes (CNTs) by liquid injection chemical vapour deposition. Polystyrene was loaded up to 4 wt% in toluene and heated to 780 °C in the presence of a ferrocene catalyst and a hydrogen/argon carrier gas in a 1:19 ratio. High resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and Raman spectroscopy were used to identify multi-walled carbon nanotubes (MWCNTs). The PS addition in the range from 0 to 4 wt% showed improved quality and CNT homogeneity; Raman “Graphitic/Defective” (G/D) values increased from 1.9 to 2.3; mean CNT diameters increased from 43.0 to 49.2 nm; and maximum CNT yield increased from 11.3% to 14.2%. Since both the CNT diameters and the percentage yield increased with respect to polystyrene addition, we conclude that carbon from the PS contributes to the carbon within the MWCNTs. The electrical contact resistance of acid washed Bucky papers produced from each loading, ranged from 2.2 to 4.4 Ohm, with no direct correlation to PS loading. Due to this narrow range, the materials with different loading were mixed to create six wires of an Ethernet cable and tested using iPerf to give uplink and downlink speeds of ~99.5 Mbps, comparable to Cu wire of identical dimension (~99.5 Mbps). The lifecycle assessment (LCA) of CNT wire production was compared to copper wire production for the use case in a Boeing 747-400 over the lifespan of the craft. Due to their lightweight nature the CNT wires decreased the CO2 footprint by 21 kTonne (kTe) over the aircraft lifespan.

Reactive transport (RT) couples bio-geo-chemical reactions and transport. RT is important to understand numerous scientific questions and solve some engineering problems. RT is highly multidisciplinary, which hinders the development of a body of knowledge shared by RT modelers and developers. The goal of this paper is to review the basic conceptual issues shared by all RT problems, so as to facilitate advance along the current frontier: biochemical reactions. To this end, we review the basic equations to point that chemical systems are controlled by the set of equilibrium reactions, which are easy to model, but whose rate is controlled by mixing. Since mixing is not properly represented by the standard advection-dispersion equation (ADE), we conclude that this equation is poor for RT. This leads us to review alternative transport formulations, and the methods to solve RT problems using both the ADE and alternative equations. Since equilibrium is easy, difficulties arise for kinetic reactions, which is especially true for biochemistry, where numerous frontiers are open (how to represent microbial communities, impact of genomics, effect of biofilms on flow and transport, etc.). We conclude with the basic 10 issues that we consider fundamental for any conceptually sound RT effort.

The inherent value and use of hydrocarbon from waste plastics and solvents can be extended through open-loop chemical recycling as this process converts plastic to range of non-plastic materials. This process is enhanced by first creating plastic-solvent-combinations from multiple sources which are then streamlined through single process stream. We report on the relevant mechanics for streamlining industrially relevant polymers such as polystyrene (PS), polypropylene (PP), high-density polyethylene (HDPE) and acrylonitrile butadiene styrene (ABS) into chemical slurries mixed with various organic solvents such as toluene, xylene and cyclohexane. The miscibility of the polymer feedstock within the solvent was evaluated using the Relative Energy Difference method, and the dissolution process was evaluated using the “Molecular theories in a continuum framework” model. These models were used to design a batch process yielding 1 tonne/h slurry by setting appropriate assumptions including constant viscosity of solvents, disentanglement-controlled dissolution mechanism and linear increase of the dissolved polymer’s mass fraction over time. Solvent selection was found to be the most critical parameter for the dissolution process. The characteristics of the ideal solvent are high affinity to the desired polymer and low viscosity. This work serves as a universal technical guideline for open-loop chemical recycling of plastics avoiding the growth of waste plastic in a circular economy framework.

The large-scale processing of Cassava (Manihot esculenta Crantz.) generates significant quantities of solid wastes annually. Cassava peels (CP) account for 5 wt.% - 30 wt.% of wastes from the processing of cassava tubers. The poor disposal and management of CP pose risks to human health, safety and the environment. Therefore, there is an urgent need to identify and examine low cost, socially acceptable and environmentally friendly strategies to mitigate the immediate and long terms disposal and management challenges. Lack of such measures results in the accumulation of CP wastes, which are currently buried, combusted, or dumped in open fields. Therefore, this paper reviewed the potential routes for the biochemical, thermochemical, and plasma valorisation of CP. The literature reviewed revealed that biochemical technologies such as anaerobic digestion (AD) and fermentation are the most widely utilised approaches currently adopted for CP valorisation. AD produces biogas (methane 50-72 vol. % and carbon dioxide 25-45 vol. %), whereas fermentation yields bioethanol. However, the numerous challenges such as substrate-induced inhibition, associated with the biochemical processes hamper microbial degradation, methane formation, and process efficiency. Furthermore, the processes generate secondary wastes or digestate/sludge, which requires additional processing before disposal. Therefore, innovative thermal, thermochemical, and plasma technologies were proposed to valorise CP into syngas, biofuels, bioenergy, biochemicals, and fertilizers, among others. However, the waste products of fermentation cannot be effectively utilised as bio-fertilizers, whereas bioethanol causes corrosion in engines. Overall, the biochemical, thermal, thermochemical and plasma technologies can effectively valorise CP for effective net energy generation.

The water quality of the river is becoming deteriorated due to human interference. It is essential to understand the relationship between human activities and land-use types to assess the water quality of a region. GIS has the latest tool for analyzing the spatial correlation. Land use land cover and change detection is the best illustration to show the human interactions on land features. The study assessed water quality index of upper Ganga River near Haridwar, Uttarakhand and spatially correlated them with changing land use to reach a logical conclusion. At the upper course of Ganga along 78 Km long from Kaudiyala to Bhogpur, water samples were collected from five stations. For water quality index the physicochemical parameters like pH, EC, DO, TDS, CaCO3-, CaCO3, Cl¯, Ca++, Mg++, Na+, K+, F-, Fe2+ were considered. The result of the spatial analysis was evaluated through error estimation and spatial correlation. The root mean square error between spatial land use and water quality index of selected sampling sites was estimated as 0.1443. The spatial correlation between land-use change and site-wise differences in water quality index has also shown a high positive correlation with R² = 0.8455. The degree of positive correlation and root mean square error has strongly indicated that the water quality of the river at the upper course of Ganga is highly impacted through human activities.

The ‘inverse problem’ of mass spectrometric molecular identification (‘given a mass spectrum, calculate/predict the 2D structure of the molecule whence it came’) is largely unsolved, and is especially acute in metabolomics where many small molecules remain unidentified. This is largely because the number of experimentally available electrospray mass spectra of small molecules is quite limited. However, the forward problem (‘calculate a small molecule’s likely fragmentation and hence at least some of its mass spectrum from its structure alone’) is much more tractable, because the strengths of different chemical bonds are roughly known. This kind of molecular identification problem may be cast as a language translation problem in which the source language is a list of high-resolution mass spectral peaks and the ‘translation’ a representation (for instance in SMILES) of the molecule. It is thus suitable for attack using the deep neural networks known as transformers. We here present MassGenie, a method that uses a transformer-based deep neural network, trained on ~6 million chemical structures with augmented SMILES encoding and their paired molecular fragments as generated in silico, explicitly including the protonated molecular ion. This architecture (containing some 400 million elements) is used to predict the structure of a molecule from the various fragments that may be expected to be observed when some of its bonds are broken. Despite being given essentially no detailed nor explicit rules about molecular fragmentation methods, isotope patterns, rearrangements, neutral losses, and the like, MassGenie learns the effective properties of the mass spectral fragment and valency space, and can generate candidate molecular structures that are very close or identical to those of the ‘true’ molecules. We also use VAE-Sim, a previously published variational autoencoder, to generate candidate molecules that are ‘similar’ to the top hit. In addition to using the ‘top hits’ directly, we can produce a rank order of these by ‘round-tripping’ candidate molecules and comparing them with the true molecules, where known. As a proof of principle, we confine ourselves to positive electrospray mass spectra from molecules with a molecular mass of 500Da or lower, including those in the last CASMI challenge (for which the results are known), getting 49/93 (53%) precisely correct. The transformer method, applied here for the first time to mass spectral interpretation, works extremely effectively both for mass spectra generated in silico and on experimentally obtained mass spectra from pure compounds. It seems to act as a Las Vegas algorithm, in that it either gives the correct answer or simply states that it cannot find one. The ability to create and to ‘learn’ millions of fragmentation patterns in silico, and therefrom generate candidate structures (that do not have to be in existing libraries) directly, thus opens up entirely the field of de novo small molecule structure prediction from experimental mass spectra.

Of the manifold concepts in drug discovery and design, covalent drugs have re-emerged as one of the most promising over the past 20-or so years. All such drugs harness the ability of a covalent bond to drive an interaction between a target biomolecule, typically a protein, and a small molecule. Formation of a covalent bond necessarily prolongs target engagement, opening avenues to targeting shallower binding sites, protein complexes, and other difficult to drug manifolds, amongst other virtues. This opinion piece discusses frameworks around which to develop covalent drugs. Our argument, based on results from our research program on natural electrophile signaling, is that targeting specific residues innately involved in native signaling programs are ideally poised to be targeted by covalent drugs. We outline ways to identify electrophile-sensing residues, and discuss how studying ramifications of innate signaling by endogenous molecules can provide a means to predict drug mechanism and function and assess on- versus off-target behaviors.

Mimosa bush (Vachellia farnesiana) is an invasive woody weed widely distributed in Australia. While it can be controlled using several mechanical and chemical techniques, this study evaluated a novel new herbicide delivery mechanism that minimizes the risk of spray drift and potential non-target damage. It was developed by Bioherbicides Australia and involves the implantation of encapsulated granular herbicides into the stem of intact plants or into the stump after cutting off plants close to ground level (cut stumped). Trials were implemented near Moree (NSW, Australia) on intact (two trials) plants and cut stumped (two trials) plants. For each trial, an untreated control plus the conventional basal bark application of a liquid formulation of triclopyr/picloram mixed with diesel was included for comparison. Encapsulated glyphosate, aminopyralid/metsulfuron-methyl, hexazinone and clopyralid were also tested in all trials. In addition, triclopyr/picloram, and metsulfuron-methyl were included in at least one of the whole plant trials. Aminopyralid/metsulfuron-methyl was consistently most effective at controlling intact plants, whilst aminopyralid/metsulfuron-methyl and clopyralid provided highest mortality when applied to cut stumps of mimosa bush. Overall, highest efficacy was achieved on single stemmed plants, but with some further refinement of the technique it should be possible to achieve similar results for multi-stemmed species.

The article reviews the constituent’s physico-chemical parameters in the water of the Mansagar Lake of the Jaipur City. The water quality is also investigated using evaluated physico-chemical parameters with in-depth study of their distribution as per sample location-wise and season-wise. A detailed discussion on the associationship among parameters (pH, Conductivity, turbidity, dissolved Oxygen, chemical and Biochemical Oxygen demand, etc.) using the Pearson’s analytical method is also presented. The strength of the article is the graphical presentation of evaluated physico-chemical parameters and the water quality indices for sample station-wise and the season-wise. To our best of understanding, first time such details have been clubbed together and discussion in brief for studied lake.

The advancement in the production and usage of the cerium oxide nanoparticles have diverted the attention of scientists towards their usage in medical field and therapeutic usage. The clinical usage of these Nano ceria is based on their ability to moderate the oxidative stress and this is only because of their ability to change their valent state from +3 to +4 which makes them ideal for scavenging radicals for use in a number of systemic and neurodegenerative disorders. This review aims to synthesize the basic methods used for the synthesis of nanoparticles along with the use of ligand, stabilizing agent and other components. This review also concludes that how various physical and chemical properties of nanoparticles effect the basic biological activities such as antimicrobial activity, cytotoxicity and many others. However, during the standardization, some of the physiochemical properties, methods used for preparation and catalytic abilities must be taken into account.

The minimum energy structures of the Si3C5 and Si4C8 clusters are planar and contain planar tetracoordinate carbons (ptCs). These species have been classified, qualitatively, as global () and local () aromatics according to the adaptive natural density partitioning (AdNDP) method, which is an orbital localization method. This work evaluates these species' aromaticity, focusing on confirming and quantifying their global and local aromatic character. For this purpose, we use an orbital localization method based on the partitioning of the molecular space according to the topology of the electronic localization function (LOC-ELF). In addition, the magnetically induced current density is analyzed. The LOC-ELF-based analysis coincides with the AdNDP study (double aromaticity, global and local). Besides, the current density analysis detects global and local ring currents. The strength of the global and local current circuit is significant, involving 4n+2 - and -electrons, respectively. The latter implicates the Si-ptC-Si fragment, which would be related to the 3c-2e -bond detected by the orbital localization methods in this fragment.

Restraint use in Australian residential aged care has been highlighted by the media, and investigated by researchers, government and advocacy bodies. In 2018, the Royal Commission into Aged Care selected ‘Restraint’ as a key focus of inquiry. Subsequently, Federal legislation was passed to ensure restraint is only used in residential aged care services as the ‘last resort’. To inform and develop Government educational resources, we conducted qualitative research to gain greater understanding of the experiences and attitudes of aged care stakeholders around restraint practice. Semi-structured interviews were held with 28 participants, comprising nurses, care staff, doctors, physiotherapists, pharmacists and relatives. Two focus groups were also conducted to ascertain the views of residential and community aged care senior management staff. Data were thematically analyzed using a pragmatic approach of inductive and deductive coding and theme development. Five themes were identified during the study: 1. Understanding of restraint; 2. Support for Legislation; 3. Restraint-free environments are not possible; 4. Low-level restraint, and 5. Restraint in the community is uncharted. Although most staff, health practitioners and relatives have a basic understanding of restraint, more education is needed at a conceptual level to enable them to identify and avoid restraint practice, particularly ‘low-level’ forms and chemical restraint. There was strong support for the new restraint regulations, but most interviewees admitted they were unsure what the legislation entailed. With regards to resources, stakeholders wanted recognition that there were times when restraint was necessary and advice on what to do in these situations, as opposed to unrealistic aspirations for restraint-free care. Stakeholders reported greater oversight of restraint in residential aged care but stated that community restraint use was largely unknown. Research is needed to investigate the extent and types of restraint practice in community aged care.

Clove (Syzygium aromaticum L. Myrtaceae) is an aromatic plant widely cultivated in tropical and subtropical countries, rich in volatile compounds and antioxidants such as eugenol, β-caryophyllene, and α-humulene. Clove essential oil has received considerable interest due to its wide application in the perfumery, cosmetic, health, medical, flavoring, and food industries. Clove essential oil has relevant biological activities to human health, including antimicrobial, antioxidant, and insecticide. This review describes the effect of the extraction method (hydrodistillation, steam distillation, ultrasound-assisted extraction, microwave-assisted extraction, cold pressing, and supercritical fluid extraction) on the chemical composition of essential oil and its correlation with their biological activities. Likewise, are summarized the main compounds and their reported biological activities. Furthermore, the main applications in clove essential oil in the food industry are presented. Finally, this review presents the new biological activities such as anti-inflammatory, analgesic, anesthetic, antinociceptive and anticancer, which are beneficial for human health. This review aims to compile the effect of different methods of extracting clove essential oil on chemical composition, food applications, as well as a current description of biological activities of interest to human health. Biological activities have increased interest in research into this essential oil and its future applications in the food or pharmaceutical industry.

Chemical flooding is one of the effective methods to recover large volumes of oil from sandstone formations after primary depletion. However, silica dissolution often occurs during Alkaline-Surfactant-Polymer (ASP) flooding, affecting the petro-physical properties of the formation. To address this issue, samples from Berea sandstone formations were treated with various brine solutions, through static tube tests and core flooding experiments. Analytical tests such as DR/2800 spectrophotometer and scanning electron microscope were used to evaluate the silica solubility and the alteration in mineral content. The results indicated that the silicate contents decreased after the saturation due to silica solubility in the solution. Increasing brine salinity to 40,000ppm and introducing Magnesium and Calcium ions to the solution, reduces the silicate contents by 5.03 % and 7.32 %. Moreover, saturating the samples with ASP solution, further reduced the silicate contents by 14.86 %. This reduction is associated with a relative increase in silica solubility and pH of the solution. Silica dissolution affects the pore microstructure, which resulted in increasing the porosity and pore volume after the core flooding. The injection of the ASP solution increased the porosity by 5.83%, thus the pore volume increased from 17.72 to 18.76cc. This is associated with the high silica solubility and the increase of solution pH in the ASP solution. The permeability of the samples generally reduced after the core flooding, due to the silica solubility. However, injecting the ASP solution, resulted in a major reduction of the permeability by more than 75%. These changes in the petro-physical properties can lead to severe formation damage, and affect hydrocarbon production. This study assists in understanding the impact of silica dissolution during ASP treatment and addresses the factors involved. Efficient utilization of chemical flooding can help mitigating silicate scaling within the formation, and extend field productivity.

Antimicrobial use (AMU) is one of the major drivers of emerging antimicrobial resistance (AMR). Surveillance of AMU, a pillar of AMR stewardship (AMS), helps devise strategies to mitigate AMR. This descriptive, longitudinal retrospective study quantified the trends in human antibiotic utilization between 2010 and 2016 using data on all antibiotics imported for systemic human use into Tanzania's mainland. Regression and time series analyses were used to establish trends in antibiotics use. A total of 12,073 records for antibiotics were retrieved, totaling 154.51Daily Defined Doses per 1,000 inhabitants per day (DID) with a mean (± standard deviation) of 22.07 (±48.85) DID. The private sector contributed 93.76%% of utilized antibiotics. The top-ranking antibiotics were amoxicillin, metronidazole, tetracycline, ciprofloxacin and cefalexin. The DDIs and percentage contribution of these antibiotics were 53.78 (34.81%), 23.86 (15.44), 20.53 (13.29), 9.27 (6.0) and 6.94 (4.49), respectively. The time series model predicted significant increase in utilization(p-value =0.002). The model forecasted that by 2022, the total antibiotics consumed would reach 89.6 DIDs, corresponding to a 13-fold increase compared to 2010. Government intervention to curb inappropriate antibiotic utilization to mitigate the rising threat of antibiotic resistance should focus on implementing AMS programs in pharmacies and hospitals in Tanzania.

Solving environmental odor issues can be confounded by many analytical, technological, and socioeconomic factors. Considerable know-how and technologies can fail to properly identify odorants responsible for the downwind nuisance odor and mitigate it for the affected citizenry. We propose enabling solutions to environmental odor issues by utilizing troubleshooting techniques developed for the food, beverage, and consumer products industries. We showed that the downwind odorant impact-priority ranking process can be definable and relatively simple. The initial challenge is the prioritization of environmental odor character from the perspective of the impacted citizenry downwind. In this research, we aim at summarizing three natural models of the rolling unmasking effect (RUE) and discuss them more systematically in the context of the proposed downwind environmental odor prioritization approach. Regardless of the size and reach of an odor source, a simplification of odor character and composition typically develops with downwind dilution. The extreme odor simplification-upon-dilution was demonstrated for two plant varieties, prairie verbena and Virginia pepperweed. Their downwind odor frontal boundaries were dominated by single, character-defining odorants; p-cresol-dominated ‘barnyard’ odor, and benzyl mercaptan-dominated ‘burnt match’ odor, respectively. The P.T. porcupine downwind odor frontal boundary was dominated by two potent, character-defining odorants: (1) ‘onion’/‘body odor’ odorant #1 and (2) ‘onion’/‘grilled’ odorant #2. In contrast with their downwind boundary simplicities, each odor source presented considerable compositional complexity and composite character difference near the source. The proposed RUE approach’s ultimate significance is the illustration of naturally occurring phenomena that explain why some environmental odors and their sources can be challenging to identify and mitigate using the analytical only approach (focused on compound identities and concentrations). These approaches rarely move beyond comprehensive lists of compounds being emitted by the source.

Modified structure along latent tracks and track formation process have been investigated in poly(allyl diglycol carbonate), PADC, which is well recognized as a sensitive etched track detector. This knowledge is essential to develop novel detectors with improved track registration property. The track structures of protons and heavy ions (He, C, Ne, Ar, Fe, Kr and Xe) have been examined by means of FT-IR spectrometry, covering the stopping power region between 1.2 to 12,000 eV/nm. Through a set of experiments on low-LET radiations – such as gamma ray -, multi-step damage process by electron hits was confirmed in the radiation-sensitive parts of the PADC repeat-unit. From this result, we unveiled for the first-time the layered structure in tracks, in relation with the number of secondary electrons. We also proved that etch pit was formed when at least two repeat-units were destroyed along the track radial direction. To evaluate the number of secondary electrons around tracks, a series of numerical simulations were performed with Geant4-DNA. Therefore, we are proposing new physical criterions to describe the detection thresholds. Futhermore, we propose a present issue of the definition of detection threshold for semi-relativistic C ions. And as a possible chemical criterion, formation density of hydroxyl group is suggested to express the response of PADC.

The aim of this study was to investigate succinic acid production from lactose concentrate, a by-product of cheese-making, using Actinobacillus succinogenes and Basfia succiniciproducens. Although the capability of these strains to metabolize different sugars is already known, their application in the conversion of lactose bears high potential for optimization. With regard to B. succiniciproducens this approach is completely novel. In particular the influence of the mediums sugar concentration and its supplementation with yeast extract to prevent a lack of proteins and vitamins were examined. Lactose based media containing sugar concentrations between 20 and 65 g L-1 and 5 g L-1 yeast extract were fermented, whereby both strains showed comparable performances. The best results in succinic acid yield and acid concentration, 0.57 g g-1 initial sugar and 23 g L1, were achieved at an initial sugar concentration of 43 g L-1. The necessity of yeast extract was demonstrated using the sugar optimized medium without supplementation. As a result, yield and concentration of succinic acid dropped to 0.34 g g-1 and 13 g L-1, the sugar consumption decreased from more than 99 to less than 55 %. Therefore the supplementation amount of 5 g L-1 yeast extract can be regarded as well-balanced.

In the search for new 2D materials beyond graphene with similar exemplary properties Stanene the new graphene relative was successfully synthesized and characterized in 2016 [14]. This new material which consists of atomically thin tin (Sn) atoms arranged in a hexagonal lattice has shown great promise in gas sensing applications in its pristine, doped and functionalized forms as evidenced by the recent research outputs following its discovery. Researchers have discovered that with its exotic properties it is highly efficient in the detection of the environmentally harmful gases like SO2, NO2, CO2, NH3 and can serve as a multifunctional gas sensor. In this focused and up-to-date review we aim to group the literature on first principles studies of stanene regards to its application for gas sensing and critically examine the success/failures of its multifunctional gas sensing properties as compared to graphene. We systematically present and discusses how structural deformations, defects and doping effect the gas sensing performance. Despite the impressive progress in the field of gas sensing with stanene shown by first principles calculations, many challenges in large scale synthesis, device fabrication and commercialization need to be addressed. The current review can help understand the current status and drawbacks of stanene and identify future directions in this field.

Most hair relaxers or straighteners used for Afro-textured hair have a pH above 11. This pH, according to international occupational health and safety guidelines, is corrosive to the skin. Further, relaxers are associated with a 3-6 times increased risk of alopecia. The skin also gets into contact with these hair straightening products during application resulting in skin irritation. Using animals as test subjects to determine these products' potential risk and safety margin is standard practice; however, with the European Union (EU) ban on animal testing, the testing method needs to be replaced by newer in vitro laboratory technologies. This study used previously and newly established in vitro cell-based technologies and human-skin derived cells as laboratory models to evaluate relaxer-induced cytotoxicity. These technologies include endpoint (MTT, CCK-8 and flow cytometry) and real-time assays (real-time cell analysis (RTCA) and extracellular flux analysis). Cellular toxicity was evident following treatment of keratinocytes and fibroblasts with acceptable concentrations of thioglycolic acid (TGA, HSCH2COOH), ammonium bisulphite (NH4HSO3), lithium hydroxide (LiOH) and sodium hydroxide (NaOH) based relaxers. Real-time assays showed significant reductions (P<0.001) in cell index and ATP production following treatment of keratinocytes with as little as one-tenth of the acceptable concentrations. Increased apoptosis (47.9%, 58.0%, 76.7% and 80.3%) also occurred in cells after treatment with TGA, NH4HSO3, NaOH and LiOH, respectively. In conclusion, this study demonstrated that using skin cells in conjunction with advanced cell-based technologies could serve as alternatives to laboratory animals for accessing the toxicity margin of hair relaxers, straighteners and other cosmetics.

Keywords: Chemical Intolerance, Drug Intolerance, Food Intolerance, QEESI, BREESI, Multiple Chemical Sensitivity, Toxicant-induced Loss of Tolerance, Prevalence

Transparent conducting oxides (TCO) with high electrical conductivity and at the same time high transparency in the visible spectrum are an important class of materials widely used in many devices requiring a transparent contact such as light-emitting diodes, solar cells and display screens. Since the improvement of electrical conductivity usually leads to degradation of optical transparency, a fine-tuning sample preparation process and a better understanding of the correlation between structural and transport properties is necessary for optimizing the properties of TCO for use in such devices. Here we report a structural and magnetotransport study of tin oxide (SnO₂), a well-known and commonly used TCO, prepared by a simple and relatively cheap Atmospheric Pressure Chemical Vapour Deposition (APCVD) method in the form of thin films deposited on soda-lime glass substrates. The thin films were deposited at two different temperatures (which were previously found to be close to optimum for our setup), 590 °C and 610 °C, and with (doped) or without (undoped) the addition of fluorine dopants. Scanning Electron Microscopy (SEM) and Grazing Incidence X-ray Diffraction (GIXRD) revealed the presence of inhomogeneity in the samples, on a bigger scale in form of grains (80–200 nm), and on a smaller scale in form of crystallites (10–25 nm). Charge carrier density and mobility extracted from DC resistivity and Hall effect measurements were in the ranges 1–3 × 10²⁰ cm⁻³ and 10–20 cm²/Vs, which are typical values for SnO₂ films, and show a negligible temperature dependence from room temperature down to -269 °C. Such behaviour is ascribed to grain boundary scattering, with the interior of the grains degenerately doped (i.e., the Fermi level is situated well above the conduction band minimum) and with negligible electrostatic barriers at the grain boundaries (due to high dopant concentration). The observed difference for factor 2 in mobility among the thin-film SnO₂ samples most likely arises due to the difference in the preferred orientation of crystallites (texture coefficient).

We introduce a number of techniques in quantitative convergent-beam electron diffraction under development by our group and discuss the basis for measuring interatomic electrostatic potentials (and therefore also electron densities), localised at sub-nanometre scales, with sufficient accuracy and precision to map chemical bonds in and around nanostructures in nanostructured materials. This has never before been possible as experimental measurements of bonding in quantum crystallography have hitherto always been restricted to homogeneous single-phased crystals.

To investigate this suitability of Black Mustard (Brassica Nigra L.) and Camelina (Camelina Sativa L.) for pulp manufacturing the nitrate-alkaline method was used. The non-wood plants were characterized by chemical analysis, especially lignin, cellulose, ash, extractives and alpha-, beta-, gamma-cellulose. The pulp was cooked in 6% nitric acid and then underwent the extraction by 5% sodium-hydroxide and neutralized by 1% acetic acid. The cooked pulp was characterized by delignification degree – Kappa number. The laboratory sheets were made from this cooked pulp and they were characterized by tensile index, breaking length, smoothness and compared with commonly available papers.

Abstract: Estimating regional soils Nitrogen and phosphorus balance in cropland is essential to improve management practices, reduce environmental risks and develop sustainable agriculture. In this study,spatial and temporal variations in crop layout, the impact on soil N and P nutrient balance were assessed from 2000 to 2015 in the West Liaohe River Basin between 2000 and 2015. The result shows that the area of cropland is on the rise, and the spatial distribution of arable land is consistent with the distribution of the main tributaries of the West Liaohe River basin. The change in planting layout for maize and soybeans has a significant impact on the nutrient balance of farmland, which plays a critical role in modifying surplus nutrients. Nutrient surpluses on farmland were mostly concentrated in areas where maize planting layout changed between 2000 and 2015. The N nutrient surplus rate decreased by 39.3%, N utilization efficiency, increased by 70.7%; P nutrient surplus rate decreased by 3.8%, and P utilization efficiency increased by 49.3%. The average utilization efficiencies of N and P nutrients were 27.8% and 9.1%, respectively, and the utilization efficiency was low. Chemical manure is the main source of nutrients. The risk of phosphorus pollution was higher than the risk of nitrogen pollution in the West Liaohe River Basin. The lower Liaohe River Basin (below the Sujiapu) was the region with the most violent changes in nitrogen and phosphorus nutrient balance. It is recommended that reduce the amount of chemical fertilizer application, especially, reduce the amount of P application, improve the ef-ficiency of nutrient use, and focus on strengthening pollution control in key areas such as the West Liaohe River lower reaches basin (below Sujiabao), reducing the risk of agricultural nonpoint source pollution.

In this tutorial review, we compare and contrast the chemical mechanisms of electrophile/oxidant sensing, and the molecular mechanisms of signal propagation. We critically analyze biological systems in which these different pathways are believed to be manifest and what the data really mean. Finally, we discuss applications of this knowledge to disease treatment and drug development.

Cotton is a potential and excellent candidate to balance both agricultural production and reme-diation of mercury-contained soil, as its main production fiber hardly involve into food chains. However, there is known rarely about the tolerance and response to Hg environments in cotton. In this study, The biochemical and physiological damages, in response to mercury (Hg), were investigated in upland cotton seedlings. The results on cottonseeds germination, indicated the germination rate were suppressed by high Hg levels, as the decrease of percentage was more than 10% at 1000 µM Hg. Shoots and roots’ growth were significantly inhibited above 10 µM Hg. The inhibitor rates (IR) in fresh weight were close between shoots and roots, whereas that in dry weight the root growth was more obviously influenced by Hg. In comparison of organs, the growth inhibition ranked as root > leaf > stem. The declining of translocation factor (TF) op-posed the Hg level even as low to 0.05 at 50 µM Hg. The assimilation of cotton plants was af-fected negatively by Hg toxicity, as evidenced from the performances on photosynthesis pig-ments (chlorophyll a and b) and gas exchange (Intercellular CO2 concentration (Ci), CO2 assimila-tion rate (Pn) and stomatal conductance (Gs)). Sick phenotypes on leaf surface included small white zone, shrinking and necrosis. Membrane lipid peroxidation and leakage were Hg dose-dependent as indicated by malondialdehyde (MDA) content and relative conductivity (RC) values in leaves and roots. More than 10 µM Hg damaged antioxidant enzyme system in both leaves and roots (P<0.05). Concludingly, 10 µM Hg post negative consequences to upland cotton plants in growth, physiology and biochemistry, whereas high phytotoxicity and damage ap-peared at more than 50 µM Hg concentration.

A brief review of the history of the problem is intended to trace the progress in the development of scientific views on the structure of water. The discoveries in this area made in the first half of the last century are considered in comparison with modern data. It is shown that due to the de facto ban on the study of the structure of water in 1971, work in this direction was frozen for a long time. The paradox is that many forgotten truths have been independently "rediscovered" in our time, which speaks of their authenticity. On the basis of scientific literature and their own research, the authors come to the conclusion that water under room conditions is a microdispersed system, one phase of which is represented by continuous water, and the other - by polywater, discovered in the 70s of the last century.

A multi-methodic analysis was performed on 5 samples of fly ashes coming from different biomasses. The aim of the study was to evaluate their possible re-use and their dangerousness for men and environment. Optical granulometric analyses indicate that the average diameter of the studied fly ashes is around 20 µm, whereas only ~1 vol% has diameter lower that 2.5 µm. The chemical composition, investigated with electron probe microanalysis, indicates that all the samples have a prevalent Ca composition, followed by Si and Al. A large content in K and P was observed in some samples, whereas the content in potentially toxic elements is always below the Italian law thresholds. Polycyclic aromatic hydrocarbons are completely absent in all the samples coming from combustion plants, whereas they are present in the fly ashes from the gasification center. Quantitative mineralogical content, determined by Rietveld analysis of X-ray powder diffraction data, indicates that all the samples have a large amorphous content, likely enriched in Ca, and several K and P minerals, such as sylvite and apatite. The results obtained from the performed chemo-mineralogical study allowed to point out that the biomass fly ashes could be interesting materials (1) as amending in clayey soils, in substitution to lime, to stimulating pozzolanic reaction and improve their geotechnical properties, on the one hand, avoiding to mine raw materials and, on the other hand, re-cycling wastes; (2) as agricultural fertilizes made by a new and ecological source of K and P.

Biomass is an attractive energy source that can be used for production of heat, power, and transport fuels, and when produced and used on a sustainable basis, can make a large contribution to reducing greenhouse gas (GHG) emissions. Anaerobic digestion (AD) is a suitable technology for reducing organic matter and generating bioenergy in the form of biogas. This study investigates the factors allowing the optimization of the process of biogas production from the co-digestion of wheat straw (WS) and bovine manure. The statistical analysis of the experiments carried out show that ultrasonic processing plays a fundamental role by sonication density and solids concentration leading to improved characteristics of WS by reducing particle size and increasing concentration of soluble chemical oxygen demand. The higher the sonicating power used, the more the waste particles are disrupted. The optimality obtained under mesophilic conditions for WS pretreated with 4% w/w (weight by weight) H2O2 at temperature 36 °C under 10 minutes of ultrasonication at 25 kHz improves the methane yield by 64%.

Over the last decade, there has been a growing interest in the use of a wide range of phytoadditives to counteract the harmful effects of heat stress in poultry. Willow (Salix spp.) is a tree with a long history. Among various forms, willow bark is an important natural source of salicin, β-O-glucoside of saligenin, but also of polyphenols (flavonoids and condensed tannins) with antioxidant, antimicrobial and anti-inflammatory activity. In light of this, the current review presents some literature data aiming to: (1) describe the relationship between heat stress and oxidative stress in broilers, (2) present or summarize literature data on the chemical composition of Salix species, (3) summarize the mechanisms of action of willow bark in heat-stressed broilers, (4) present different biological effects of the extract of Salix species in different experimental models.

Increasing genetic diversity in crop plants has been used for chemical mutagenesis. Through the application of various mutagenic agents, over 430 new varieties have been derived as rice mutants (Oryza sativa L.) Chemical mutagens such as ethyl methane sulphonate (EMS), diepoxybutane derivative (DEB), sodium azide, and gamma ray, x-ray, and quick neutron irradiation have been commonly used to induce a large number of functional variations in rice and others crops. Among chemical mutagens, ethyl methane sulfonate (EMS) is the alkylating agent most widely used in plants because it induces nucleotide substitutions to be extremely frequent, as detected in various genomes. In this study, seeds of potential genotype of the popular variety, (Oryza sativa L. Super Basmati variety) were treated with EMS at concentrations of 0.25%, 0.50%, 0.75%, 1% and 1.5%. Various measurements on the M1 generation determined EMS sensitivity. As concentration of applied EMS increased, will decrease in germination, shoot length, root length, plant height, productive tillers, Panicle Length, Total Spikelet, sterile spikelet and fertility under field conditions were observed in M1 generation as compared to the non-treatment control. Emergence, shoot length, root length, plant height, productive tillers, Panicle Length, Total Spikelet, sterile spikelet and fertility also decreased with increases in EMS mutagenesis in an approximately linear fashion. The LD₅₀ values were observed based on growth reduction of seedlings after EMS treatment with 0.25% and 0.50% on the rice variety (Oryza sativa L. spp.).

The question of molecular similarity is core in cheminformatics, and is usually assessed via a pairwise comparison based on vectors of properties or molecular fingerprints. We recently exploited variational autoencoders to embed 6M molecules in a chemical space, such that their (Euclidean) distance within the latent space so formed could be assessed within the framework of the entire molecular set. However, the standard objective function used did not seek to manipulate the latent space so as to cluster the molecules based on any perceived similarity. Using a set of some 160,000 molecules of biological relevance, we here bring together three modern elements of deep learning to create a novel and disentangled latent space, viz transformers, contrastive learning, and an embedded autoencoder. The effective dimensionality of the latent space was varied such that clear separation of individual types of molecules could be observed within individual dimensions of the latent space. The capacity of the network was such that many dimensions were not populated at all. As before, we assessed the utility of the representation by comparing clozapine with its near neighbours, and did the same for various antibiotics related to flucloxacillin. Transformers, especially when as here coupled with contrastive learning, effectively provide one-shot learning, and lead to a successful and disentangled representation of molecular latent spaces that at once uses the entire training set in their construction while allowing ‘similar’ molecules to cluster together in an effective and interpretable way.

Trachymene incisa subsp. incisa is an Australian endemic taxon that varies greatly in the abundance and length of the leaf trichomes. The essential oil composition of five populations of this subspecies, three corresponding to the typical glabrous form and two of the particularly hairy variant, has been analyzed in an attempt to determinate if that variability is also reflected in their composition. The oils have been extracted by hydrodistillation and analysed by Gas Chromatography (GC) and Gas Chromatography coupled to Mass Spectrometry (GC-MS). The essential oils of T. incisa subsp. incisa were characterized by the high amount of sesquiterpenes that were the major fraction. The sesquiterepene hydrocarbons were significantly higher in the hairy variant in comparison to the glabrous one. According to the main compound three different chemotypes were found: I.- -selinene + bicyclogermacrene and II.- -bisabolene + -pinene for the typical glabrous variant and III.- bicyclogermacrene + -caryophyllene for the hairy variant.

Carbon capture and storage has gotten increased attention during the last decade, and several full-scale projects are currently being planned. This requires transportation of large quantities of CO2 from the capturing plant to the end point. From economic and public acceptance point of view it is important to ensure that the transportation system is operated in a safe manner. Thus, avoiding threats like corrosion or formation of particles are important. It is therefore required to monitor that the transported CO2 fulfils the required specifications, and in practice this means that the impurity content of the CO2 must be analysed. CO2 will in most cases be transported in the liquid or supercritical state (high pressure), which makes the practicalities around chemical analysis more difficult. Phase transition from liquid or supercritical state to gaseous state may also introduce several physiochemical effects that may affect the analysis. This paper discusses technical and practical challenges with such types of analysis. Most of this work is based on experience that was gained during development of analytical system for dense phase CO2 in a joint industry project that studied corrosion and chemical reactions in a simulated CO2 transport system.

In this paper, a novel synthesis for a chemical precursor for nanocrystalline VO2 coatings is elaborated. The compatibility of the precursor towards the substrate is optimized for spin coating. This is done by subjecting multiple solvents to contact angle measurements. A suitable thermal treatment is developed to densify the coating and to induce crystallization. Afterwards the microstructure of the coating is investigated using X-Ray diffraction, electron microscopy and ellipsometry techniques. To assess the thermochromic properties of the fabricated device, optical transmission experiments were conducted both at room temperature and at elevated temperature. A correlation between these thermochromic properties and coating thickness was investigated in order to obtain an optimized thermochromic device, where both high visual transparency and prominent thermochromic switching abilities are aimed for. In this work, an optimal coating thickness is proposed for a thermochromic coating with high switching ability and solar modulation.

This investigation was conducted to determine the chemical composition and nutritional value of five plant species commonly used as ruminant feeds namely: Artemisia herba-alba, Acer monspessulanum, Amygdalus lycoides, Amygdalus scoparia, and Atriplex leucoclada. After the collecting samples, the chemical compositions of plants included dry matter (DM), organic matter (OM), crude protein (CP), ether extract (EE), ash (CA), cell wall (NDF), and non-lignin cell wall (ADF) were determined according to standard methods. For degradation testing, the nylon bag technique was applied using three native Sistani fistula calves. Organic matter digestibility (OMD) and metabolisable energy (ME) were determined through the gas production technique. The CP value ranged from 5.30 (Amygdalus scoparia) to 11.72% (Atriplex leucoclada) while NDF value ranged from 52.62 (Amygdalus lycoides) to 69.05% (Amygdalus scoparia). The range of OMD, DOMD, and ME was from 36.67 to 53.27%, 34.67 to 49.11%, and 5.57 to 8.08 (MJ/kg), respectively. The results showed a positive correlation between cell wall composition and dry matter digestibility in plant species. The nutritional value of Amygdalus lycoides, Atriplex leucoclada, Acer monspessulanum, and Artemisia herba-alba was acceptable composition and digestibility.

Pseudomonas aeruginosa is a Gram-negative bacillus included among the six "ESKAPE" microbial species with an outstanding ability to "escape" currently used antibiotics and developing new antibiotics against it is of the highest priority. Whereas minimum inhibitory concentration (MIC) values against Pseudomonas aeruginosa have been used previously for QSAR model development, disk diffusion results (inhibition zones) have not been apparently used for this purpose in the literature, and we decided to explore their use in this sense. We developed multiple QSAR methods using several machine learning algorithms (Support vector classifier, K Nearest Neighbors, Random Forest Classifier, Decision Tree Classifier, AdaBoost Classifier, Logistic Regression, and Naive Bayes Classifier). The main descriptors used in building the models belonged to the families of adjacency matrix, constitutional descriptors, first highest eigenvalue of Burden matrix, centered Moreau-Broto autocorrelation, and averaged and centered Moreau-Broto autocorrelation descriptors. A total of 32 models were built, of which 28 were selected and stacked to create a meta-model. In terms of balanced accuracy, the best performance was provided by KNN, SVM and AdaBoost algorithms, but the ensemble method had slightly superior results in nested cross-validation.

By taking advantage of a stability criterion established recently, the critical temperature T_c is reckoned with help of the microscopic parameters, characterising the normal and superconducting electrons, namely the independent-electron band structure and a repulsive two-electron force. The emphasis is laid on the sharp T_c dependence upon electron concentration and inter-electron coupling, which might offer a practical route toward higher T_c values and help to understand why high-T_c compounds exhibit such remarkable properties.

The main bottleneck when performing computational fluid dynamics (CFD) simulations of combustion systems is the computation and integration of the highly non-linear and stiff chemical source terms. In recent times, machine learning has emerged as a promising tool to accelerate combustion chemistry, involving the use of regression models to predict the chemical source terms as functions of the thermochemical state of the system. However, combustion is a highly nonlinear phenomenon, and this often leads to divergence from the true solution when the neural network representation of chemical kinetics is integrated in time. This is because these approaches minimize the error during training without guaranteeing successful integration with ordinary differential equation (ODE) solvers. In this work, a novel neural ODE approach to combustion modeling, ChemNODE, is developed to address this issue. The source terms predicted by the neural network are integrated during training, and by backpropagating errors through the ODE solver, the neural network weights are adjusted accordingly to minimize the difference between the predicted and actual ODE solutions. It is shown that even when the dimensionality of the thermochemical manifold is trimmed to remove redundant species, the proposed approach accurately captures the correct physical behavior and reproduces the results obtained using the full chemical kinetic mechanism.

The innovation of the new psychoactive substances (NPS) market requires the rapid identification of new substances that can be a risk to public health, in order to reduce the damage due to their use. Twelve seized products suspected to contain illicit substances were analyzed by attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), gas chromatography coupled to mass spectrometry (GC-MS), and nuclear magnetic resonance spectroscopy (NMR). Synthetic cathinones (SCat) were found in all products, either as a single component or in mixtures. Infrared spectra of all products were consistent with the molecular structure of SCat, showing an intense absorption band at 1700–1674 cm‐1, corresponding to the carbonyl stretching, a medium/strong peak at 1605-1580 cm-1, indicating stretching vibrations in the aromatic ring (C=C) and bands with relative low intensity at frequencies near 2700–2400 cm-1, corresponding to an amine salt. It was possible to identify a total of eight cathinone derivatives by GC-MS and NMR analysis: 4’-methyl-α-pyrrolidinohexanophenone (MPHP), α-pyrrolidinohexanophenone (α-PHP), 3-fluoromethcathinone (3-FMC), methedrone, methylone, buphedrone, N-ethylcathinone, and pentedrone. Among the adulterants found in these samples, caffeine was the most frequently detected substance, followed by ethylphenidate. These results highlight the prevalence of SCat in seized materials of the Portuguese market. Reference standards are usually required for confirmation, but when reference materials are not available, the combination of complementary techniques is fundamental for a rapid and an unequivocal identification of such substances.

A plenty of theories on the origin of genetic codes have been proposed so far, yet all ignored the energetic driving force, its relation to the biochemical system, and most importantly, the missing “matchmaker” between proteins and nucleic acids. Here, a new hypothesis is proposed, according to which ATP is at the origin of the primordial genetic code by driving the coevolution of the genetic code with the pristine biochemical system. This hypothesis aims to show how the genetic code was produced e.g. by photochemical reactions in a protocell that derived from a lipid vesicle enclosing various life’s building blocks (e.g. nucleotides and peptides). At extant cell, ATP is the only energetic product of photosynthesis, and is at the energetic heart of the biochemical systems. ATP could energetically form and elongate chains of both polynucleotides and polypeptides, thus acting a “matchmaker” between these two bio-polymers and eventually mediating precellular biochemical innovation from energy transformation to informatization. ATP was not the only one that could drive the formation of polynucleotides and polypeptides, but favored by precellular selection. The protocell innovated a photosynthesis system to produce ATP efficiently and regularly with the aids of proteins and RNA/DNA. The completion of permanently recording the genetic information by DNA marked the dawn of cellular life operated by Darwinian evolution. The ATP hypothesis assumes or supports the photochemical origin of life, shedding light on the origins of both photosynthetic and biochemical systems, which remains largely unknown thus far. Based on ATP hypothesis, virus (like the new coronavirus) could not be the earliest life on Earth, as it has neither biochemical systems nor lipid bilayer membrane that provided relatively isolated environment for the development of protobiochemical reactions, although it owns the genetic code of a cellular life. Virus could not be a bridge between life and non-life, but is an anti-life substance, as it depletes cellular material for its own replication, and then spreads by destroying the host cells. It can be imagined that if cellular life are completely wiped out by the virus, the complete destruction of life on Earth would be inevitable.

The effectiveness of forest resources depends on the comprehensiveness and rationality of their consumption and processing into finished products. This article discusses a problem of utilising solid fir wood greenery residues generated during the industrial production of essential oils. Bioconversion is considered to be the most promising utilization method. The objective of this research was to study the chemical composition of bioconversion products of fir wood greenery-based substrates. The РР-3.2 strain of Pleurotus pulmonarius (Fr.) Quél was used as a biodestructor. In the process of bioconversion, the contents of polysaccharides and lignin substances is reduced to 38 and 28 % respectively. Up to 20 % of protein accumulates in bioconversion products of fir wood greenery. The amount of nucleic acids is not more than 1.5 g per 1 kg, the contents of heavy metals, such as mercury, cadmium, arsenic, lead, do not exceed maximum permissible concentration standards. The substrate weight loss reaches 15 %. When fallen leaves and post-extraction poplar bud residues are added to the substrate, the substrate-destroying activity of fungi rises, as well as the protein content increases by 3 %. The digestibility of products as a result of bioconversion increases 1.6–2.8 times depending on the substrate composition. The obtained data enable to recommend post-fermented substrates based on fir wood greenery and balsam poplar biomass for use as a protein feed additive.

Ti6Al4V samples obtained by selective laser melting were subjected to acid treatment, chemical oxidation in hydrogen peroxide solution and subsequent thermochemical treatment. The effect of temperature and time of acid etching of Ti6Al4V samples on surface roughness, morphology, topography and chemical and phase composition after the thermochemical treatment was studied. The surfaces were characterized using scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction and contact profilometry. Pore and protrusion sizes were measured. Acid etching modified the elemental composition and surface roughness of the alloy. Temperature had a greater influence on the morphology, topography and surface roughness of samples than time. Increases in roughness values were observed when applying successive chemical oxidation and thermochemical treatment compared to the values observed on surfaces with acid etching. After the thermochemical treatment, the samples with acid etching at a temperature of 80 °C showed a multiscale topography. In addition, a network-shaped structure was obtained on all surfaces, both on their protrusions and pores previously formed during the acid etching.

2,5-Di(hydroxymethyl)furan (DHMF) is a high-value chemical block than can be synthesized from 5-hydroxymethylfurfural (HMF), a platform chemical that results from the dehydration of biomass-derived carbohydrates. In this work, the HMF biotransformation capability of different Fusarium species was evaluated and F. striatum was selected to produce DHMF. The effects of the inoculum size, glucose concentration and pH of the media over DHMF production were evalu-ated by a 23 factorial design. A substrate feeding approach was found suitable to overcome the toxicity effect of HMF towards the cells when added at high concentrations (>75 mM). The pro-cess was successfully scaled-up at bioreactor scale (1.3 L) with excellent DHMF production yields (95%) and selectivities (98%). DHMF was purified from the reaction media with high recovery and purity by organic solvent extraction with ethyl acetate.

The ubiquity of amino acids in carbonaceous meteorites has suggested that amino acids are widespread in the Universe, serving as a common class of components for the emergence of life. However, parameters for modeling amino acid polymerization at mineral–water interfaces remain limited, although the interfacial conditions inevitably exist on planets with surface liquid water. Here, we present a set of extended triple-layer model parameters for aspartate (Asp) and aspartyl-aspartate (AspAsp) adsorptions on ferrihydrite, anatase, and γ-alumina determined based on the experimental adsorption data. By combining the parameters with the reported thermodynamic constants for amino acid polymerization in water, the impacts of these minerals on Asp dimerization are calculable over a wide range of environmental conditions. It was predicted, for example, that ferrihydrite strongly increases the AspAsp/Asp equilibrium ratio in neutral to acidic pH; the ratio in the adsorbed state reaches 40% even from a low Asp concentration (0.1 mM) at pH 4. This percentage is approximately 5 × 107 times higher than that attainable without mineral (8.5 × 10–6%). Our exemplified approach enables us to screen wide environmental settings for abiotic peptide synthesis from a thermodynamic perspective, thereby narrowing down the geochemical situations to be explored for life’s origin on Earth and Earth-like habitable planets.

The CARA program has been developed since 2008 by the French reference laboratory for air quality monitoring (LCSQA) and the regional monitoring networks to gain a better knowledge at the national level on the particulate matter (PM) chemistry and its diverse origins in urban environments. It results of strong collaborations with international-level academic partners, allowing to bring state-of-the-art, straightforward and robust results and methodologies within operational air quality stakeholders (and subsequently, decision makers). Here, we illustrate some of the main outputs obtained over the last decade thanks to this program, regarding methodological aspects (both in terms of measurement techniques and data treatment procedures) as well as acquired knowledge on the predominant PM sources. Offline and online methods are used following well-suited quality assurance and quality control procedures, notably including inter-laboratory comparison exercises. Source apportionment studies are conducted using various receptor modeling approaches. Overall, the results presented herewith underline the major influences of residential wood burning (during the cold period) and road transport emissions (exhaust and non-exhaust ones, all along the year), as well as substantial contributions of mineral dust and primary biogenic particles (mostly during the warm period). Long-range transport phenomena, e.g., advection of secondary inorganic aerosols from the European continental sector and of Saharan dust into the French West Indies, are also discussed in this paper. Finally, we briefly address the use of stable isotope measurements (δ15N) and of various organic molecular markers for a better understanding of the origins of ammonium and of the different organic aerosol fractions, respectively.

This paper describes the state of the art and future opportunities for process design and sustainable development. In the Introduction the main global megatrends and European Union's response to two of them, the European Green Deal, are presented. The organization of professionals in the field, their conferences and publications support the two topics. A brief analysis of the published documents in the two most popular databases shows that the environmental dimension predominates, followed by an economic one, while the social pillar of sustainable development is undervalued. The main design tools for sustainability are described. As an important practical case, the European chemical and process industries are analyzed and their achievements in sustainable development are highlighted; in particular, their strategies are presented in more detail. The conclusions cover the most urgent future development areas of the process industries, carbon capture with utilization or storage, process analysis, simulation, synthesis and optimization tools; zero waste, circular economy and resource efficiency already play an important role. However, more profound changes are needed in the coming decades, including a shift away from growth with changes in habits, lifestyles and business models. Lifelong education for sustainable development will play a very important role in the growth of democracy and happiness instead of consumerism and neoliberalism.

Various techniques have been used to “clean-up” industrial phosphoric acid: precipitation, flotation, activated charcoal or clay treatment. To address membrane processes potential in phosphoric acid clarification process, this study explores the advantage of membrane techniques as new route for phosphoric acid clarification in an eco-efficient way through the use of “regenerated spent membrane”. Regeneration of the spent membranes was performed on of 0.15 m2 active area regeneration. These membrane samples were used to study the phosphoric acid clarification at a laboratory scale. They were immersed in an oxidizer for at most seven days. The samples were characterized systematically before immersion in an oxidant media. In this study, the potential to regenerate spent membranes and application of this media to clarify the 29% P2O5 phosphoric acid was demonstrated. This study shows, by tests that the reverse osmosis (RO) membranes achieve an abatement of 70% and 65% for solids and organic materials, respectively. These positive results will pave the way for implementing these membranes phosphoric acid treatment process. Moreover, besides being economically advantageous, the use of the spent membrane is likely an environmentally friendly route (no waste, no organic solvent and effluent to be regenerated later on).

MXenes are two-dimensional nanomaterials isolated from MAX phases by the selective extraction of the A component —a p-block element. The MAX phase exfoliation energy, Eexf, is regarded as a chemical descriptor of the MXene synthesizability. Here we show, by density functional theory estimations of the Eexf values for 486 different MAX phases, that Eexf decreases i) when MAX is a nitride, ii) when going along a d series of the metal M component, iii) when going down a group of the p-block A element, as well as iv) when having thicker MXene phases. Furthermore, Eexf is found to bias, even to govern, the surface chemical activity, as evaluated here on the CO2 adsorption strength, so that more unstable MXenes, displaying larger Eexf values, display a stronger attachment of species upon.

Citrus essential oils (EOs) have various bioactivities like antioxidants, with many applications. Antioxidant activities depend on the chemical compositions of the EOs, which are affected by climate, soil, and geographical region. Thus, investigations on chemical compositions and antioxidant activities of Citrus EOs in different countries are valuable. In this study, we distilled EOs from peels of Indonesian-grown Citrus, including C. nobilis, C. limon, C. aurantifolia, C. amblycarpa, and Citrus spp.Chemical compositions of EOs were analyzed using Gas Chromatography-Mass Spectrometer (GC-MS), whereas the antioxidant activities were determined by employing 2,2-diphenyl-2-picrylhydrazyl (DPPH) method. Furthermore, principal component analysis (PCA) was applied to elucidate the main contributing compounds for antioxidant activity. The results show that all EOs possess unique chemical characteristics, with limonene as the majority constituent. For antioxidant activities, C. limon and C. amblycarpa EOs are the two strongest, IC50 values below 7.00 μL/mL. PCA approach suggests that -terpinene mainly contributes to the high antioxidant activities of C. limon and C. amblycarpa. Moreover, o-cymene, thymol, p-cymene, and α-pharnesene may also be responsible for the antioxidant activity of C. limon EO. These results are valuable information for the applications of Citrus EOs as antioxidant sources.

The coffee leaf miner (CLM) Leucoptera coffeella moth is a major threat to coffee production. Insect damage is related to the feeding behavior of the larvae on the leaf. During the immature life stages, the insect feeds in the mesophyll, triggering necrosis and causing loss of photosynthetic capacity, defoliation, and significant yield loss to coffee crops. Chemical control is mandatory to sustain the coffee production chain, though market requirements move towards conscious consumption, claiming for more sustainable methods. In this overview, we discuss aspects about the CLM concerning biology, history, geographical distribution, economic impacts, and the most relevant control strategies in progress. Insights to develop an integrate approach for a safer and eco-friendly control of the CLM are discussed, including bio-extracts, nanotechnology, pheromones, and tolerant cultivars.

According to the French Agency for Food, Environmental and Occupational Health & Safety, electromagnetic hypersensitivity affects more than 3 million people in France, and headaches are a very frequent cause of complaint in electrohypersensitive patients, to the point of dominating the clinical picture. These headaches share characteristics with migraine pathology, and clinical improvement with anti-migraine therapy has led us to consider that the headache in the electrohypersensitive patient may be a variant of the migraine disease mediated by the TRPA1 receptor, which if confirmed, would offer effective therapeutic possibilities to relieve the electrohypersensitive patient.

This review summarizes experimental and theoretical studies of transition metal complexes with two types of novel metal-carbon bonds. One type features complexes with carbones CL2 as ligands, where the carbon(0) atom has two electron lone pairs which engage in double (σ and π) donation to the metal atom [M] CL2. The second part of this review reports complexes which have a neutral carbon atom C as ligand. Carbido complexes with naked carbon atoms may be considered as endpoint of the series [M]-CR3 → [M]-CR2 → [M]-CR → [M]-C.

A methodology based on the concepts that arise from Density Functional Theory named Conceptual Density Functional Theory (CDFT) was chosen for the calculation of some global and local reactivity descriptors of the Discodermins A-H family of marine peptides through the consideration of the KID (Koopmans in DFT) technique that was successfully used in previous studies of this kind of molecular systems. The determination of active sites of the studied molecules for different kind of reactivities was achieved by resorting to some CDFT-based descriptors like the Fukui functions as well as the Parr functions derived from Molecular Electron Density Theory (MEDT). A few properties identified with their ability to behave as a drug and the bioactivity of the peptides considered in this examination were acquired by depending on a homology model by studying the correlation with the known bioactivity of related molecules in their interaction with various biological receptors. With the further object of analyzing their bioactivity some parameters of usefulness for future QSAR studies, their predicted biological targets and the the ADME (Absorption, Distribution, Metabolism, and Excretion) parameters related to the Discodermins A-H pharmacokinetics are also reported.

This paper examines whether classical extensional mereology is adequate for formalizing the whole-parts relation in quantum chemical systems. Although other philosophers have argued that classical extensional and summative mereology does not adequately formalize whole-parts relation within organic wholes and social wholes, such critiques often assume that summative mereology is appropriate for formalizing the whole-parts relation in inorganic wholes such as atoms and molecules. However, my discussion of atoms and molecules as they are conceptualized in quantum chemistry will establish that standard mereology cannot adequately fulfill this task, since the properties and behavior of such wholes are context-dependent and cannot simply be reduced to the summative properties of their parts. To the extent that philosophers of chemistry have called for the development of an alternative mereology for quantum chemical systems, this paper ends by proposing behavioral mereology as a promising step in that direction. According to behavioral mereology, considerations of what constitutes a part of a whole is dependent upon the observable behavior displayed by these entities. Thus, relationality and context-dependence are stipulated from the outset and this makes behavioral mereology particularly well-suited as a mereology of quantum chemical wholes. The question of which mereology is appropriate for formalizing the whole-parts relation in quantum chemical systems is relevant to contemporary philosophy of chemistry, since this issue is related to the more general question of the reducibility of chemical wholes to their parts and of the reducibility of chemistry to physics, which have been of central importance within the philosophy of chemistry for several decades. More generally, this paper puts contemporary discussions of mereology within the philosophy of chemistry into a broader historical and philosophical context. In doing so, this paper also bridges the gap between formal mereology, conceived as a branch of formal ontology, and ‘applied’ mereology, conceived as a branch of philosophy of science.

Keenjhar Lake is the main source of drinking water for the metropolitan city of Karachi. The release of untreated wastewater from Kotri industrial area and other sources have made the lake water polluted. This study was subjected to determine the impacts of such pollutant sources on the water quality of Keenjhar Lake. The study involves the analysis of water quality parameters of Keenjhar Lake and its Feeding source (KB Feeder). The sampling sites were selected based on the sources of contamination. The water samples are tested for physical, chemical and microbiological parameters. The result of water analysis indicates the contamination level of the lake is quite alarming for the sites of Kotri effluent and WAPDA colony where Total Dissolved Solids (TDS), Chloride and other ionic metals were quite higher in concentration than other sites. These sites are also contaminated with Fluoride and Arsenic which are carcinogenic elements. The study reveals that the contamination level of feeding source is causing big non-reversible damage to the lake if continued to be uncontrolled. This contamination is mainly due to the release of toxic metals and ions in the KB feeder caused by human carelessness.

The simultaneous evaluation of heat/mass transference procures momentous significance in the polymer industry and engineering activities. Extensive utilization of such aspects includes propylene flares, heat exchangers, energy transfiguration in chilling towers, and amputation of post fortuitous heat in nuclear reactors. Owing to such prospective demands, we interpreted the Jeffrey liquid reactive flow under non-linear convection. We scrutinized the transference of heat/mass under generalized Fourier-Fick relations. Thermal conductivity depends on temperature while mass diffusivity is dependent on concentration. Besides, heat source along with first-order chemical reaction aspects are accounted for. Relevant transformations are exerted to achieve non-linear differential systems that are solved through the homotopy scheme. Influences of divers factors are exhibited via graphical benchmark.

The aim of the present study was to assess the efficacy of All Cosmos Industries (ACI) bio-organic and bio-chemical fertilizers and ACI N-Fixer (N-Bio Booster) on the paddy yields based on the field trial plots at Langkat, Medan, Indonesia. This application of ACI bio-organic fertilizer (NPK 5/5/5) and ACI bio-chemical (NPK 15/15/15) fertilizer and ACI N-Fixer tests were conducted at the paddy farm at Langkat from May-October 2018. This study employed a factorial randomized complete block design which consisted of two factors, namely: Factor I with four types of fertilizers while Factor II consisted of two paddy varieties (Inpari 30 and Inpari 32). Overall, the filled grains in the ACI treatments are significantly (P< 0.05) higher than those in the control treatments that used Normal Chemical Compound NPK. Overall, total weight per meter² (368-617g) in ACI treatments are also significantly (P< 0.05) higher than those (319-371g) in the control treatments. At harvesting time at 105 days after transplanting, significantly higher (P< 0.05) colony counts (13-15 x 10⁶ CFU/mL) (for ACI treatments), than those (8 x 10⁶ CFU/mL) in the controls positively indicated higher total yields of paddy grains per hectare. It was found that the application of ACI bio-organic and bio-chemical fertilizers and ACI N-Fixer can improve paddy yields of the two rice varieties, between 16.4-38.2% (up to 5.75 MT/ha), in the field trial plots at Langkat. These commercial fertilizers play an imperative role in refining the soil fertility and thereby can increase the yield of rice production. Therefore, it is highly recommended that ACI bio-organic and ACI bio-chemical fertilizers and ACI N-Fixer (N-Bio Booster) can be employed to increase the paddy yield in this region.

An elevated level of endoplasmic reticulum (ER) stress is considered an aggravating factor for inflammatory bowel disease (IBD). To develop an ER stress attenuator that is effective against colitis, 4-phenylbutyric acid (4-PBA), a chemical chaperone that alleviates ER stress, was conjugated with acidic amino acids to yield a 4-PBA-glutamic acid conjugate (PBA-GA) and a 4-PBA-aspartic acid conjugate (PBA-AA). The PBA derivatives were converted to 4-PBA in the cecal contents, where the conversion was greater with PBA-GA. After oral administration of PBA-GA (oral PBA-GA), millimolar levels of PBA were accumulated in the cecum, whereas 4-PBA was not detected in the blood, indicating the targeting of PBA-GA to the large intestine. At concentrations in the cecum achievable by oral PBA-GA, 4-PBA effectively attenuated ER stress in human colon epithelial cells. In 2,4-dinitrobenzenesulfonic acid-induced colitis in rats, oral PBA-GA alleviated the damage and inflammation in the colon. Moreover, oral PBA-GA substantially reduced the elevated levels of ER stress marker proteins in the inflamed colon. Moreover, PBA-GA was as effective as the currently used anti-IBD drug, sulfasalazine. In conclusion, PBA-GA is a colon-targeted prodrug of 4-PBA and is effective against rat colitis probably through the attenuation of ER stress in the inflamed colon.

Around the World, the number of compound databases of natural products in the public domain is rising. This is in line with the increasing synergistic combination of natural product research and chemoinformatics. Towards this global endeavor, countries in Latin America are assembling, curating, and analyzing the contents and diversity of natural products available in their geographical regions. In this manuscript we collect and analyze the efforts that countries in Latin America have made so far to build natural product databases. We further encourage the scientific community in particular in Latin America, to continue their efforts to building quality natural product databases and, whenever possible, to make them publicly accessible. It is proposed that all compound collections could be assembled into a unified resource called LANaPD: Latin America Natural Products Database. Opportunities and challenges to build, distribute, and maintain LANaPD are also discussed

We have conducted a comprehensive year-long sampling campaign for particulate matter (PM) pollutants at a site near a major highway, following standard protocols. Total mass, and elemental and chemical composition of the fine fractions (PM2.5) of traffic-related pollutants are determined utilizing several complementary techniques. These complementary techniques included gravimetric analysis, X-ray fluorescence (XRF), scanning electron microscopy and energy dispersive spectroscopy, X-ray diffraction (XRD) and black carbon multi-wavelength absorption. The results show that the PM2.5 mass concentrations are within or slightly above international standards and include natural dust and anthropogenic pollutants such as black carbon, sulfates and other traffic-related elements. Anthropogenic sources include the secondary pollutants Mascagnite and Koktaite, traffic emissions such as exhaust emissions and tires, brakes and road erosions. It was found that the sulfates are the highest contributors to PM2.5 (~40%), as evident from XRD results and the S content in the XRF analysis.

Among other species, Black Soldier Fly (Hermetia illucens, HI, Diptera, Stratiomydae) has the great potential as food and feed ingredient in the EU, particularly thanks to its preference for organic waste as growth substrate. The production of insects as livestock feed or as food ingredient requires a strict monitoring of heavy metal content in the growth substrate in order to secure its safe. This study aims to investigate the presence of toxic metals cadmium, lead, mercury, arsenic, and nickel in HI prepupae and their growth substrates based on coffee roasting by-product and microlagae Schizochytrium sp. and Isochrysis sp. Analyses were carried out via graphite furnace atomic absorption spectrophotometry for Cd, Pb, Ni, and As, and via Direct Mercury Analyzer for Hg. All metal concentrations found in growth substrates were below the legal limit of undesirable substances in animal feed (2002/32/EC). Metals concentrations in HI prepupae were in the range (mg kg-1 wet weight): Cd 0.072–0.084, Pb 0.018–0.026, Hg 0.010–0.032, As 0.036–0.047, Ni 0.18–0.76. HI prepupae accumulate Cd, Pb and Hg, but our results indicate that the risk of exposure to metals from consumption of HI prepupae is relatively low and in compliance with European Union regulations.

The New Zealand brushtail possum (Trichosurus vulpecula), introduced from Australia in the 1850s, is an invasive species that is widespread throughout New Zealand and forms the largest self-sustained reservoir of bovine tuberculosis (Mycobacterium bovis) in the wild. Conservation and agricultural authorities regularly apply a series of population control measures to suppress brushtail possum populations. The evolutionary consequence of more than half a century of intensive population control operations on the species genomic diversity and population structure is hindered by a paucity of available genomic resources for the species. This study is the first to characterise the functional content and diversity of brushtail possum liver and brain cerebral cortex transcriptomes. Raw sequences from hepatic cells and cerebral cortex were assembled into 58,001 and 64,735 transcripts in hepatic cells and cerebral cortex, respectively. Functional annotation and polymorphism assignment of the assembled transcripts demonstrated a considerable level of variation in the core metabolic pathways that represent potential targets for selection pressure exerted by chemical toxicants. This study suggests that the brushtail possum population in New Zealand harbours considerable levels of variation in metabolic pathways that could potentially promote the development of tolerance against chemical toxicants.

In order to obtain makhwean (MK) fruit essential oil of constant aromatic profile during raw material sourcing, evaluation of relationship between genotype, phenotype and chemical profiles are necessary. Three specimens of the MK (MK1-3) distributed in Northern Thailand were genetically and morphologically compared with other Zanthoxylum spices known locally as mamaad (MM) and makwoung (MKO), respectively. MM was taxonomical confirmed as Z. armatum based on plant structure and leaf characteristic (Odd-pinnately compound leaf). MKO and MK were identified as Z. rhetsa and Z. myriacanthum using number of petals and anthers. Genetic sequencing by Internal Transcribed Spacer (ITS) sequence and Random Amplified Polymorphic DNA moreover, divided these Zanthoxylum spps. into three groups accordingly to their species viz., MM, MKO and MK. Essential oil of the dried fruits from these samples was extracted and analysed for physical and chemical profiles. Cluster analysis (PCA-biplot) of volatile compositions was able to separate 1) MK1 and MK3 with limonene as leading component, 2) MK2 and MKO related with sabinene and β-philandrene, 3) MM with linalool. By using odour attribute representatives, the essential oil of MKO and MK1-3 were closely related possessing fruity, woody and citrus aromas, while the MM was sweet/ floral. In summary for MK raw material sourcing, plant genotyping played the most important role to odour characteristics than growing locations, thus plant species confirmation should be first considered.

Henry’s constants for different existing compounds in water have great importance in transfer calculations. Measurement of these constants face different difficulties including high costs of experiment and low accuracy of measurement apparatus. Due to these facts, proposing a low cost and accurate approach becomes highlighted. To this end, adaptive neuro-fuzzy inference system (ANFIS) and least squares support vector machine (LSSVM) have been used as Henry’s constant predictor tools. The molecular structure of compounds has been used as inputs of models. After training the models, the visual and mathematical studies of outputs have been done. The coefficients of determination of LSSVM and ANFIS algorithms are 0.999 and 0.990 respectively. According to the comprehensiveness of databank and accurate prediction of algorithms, it can be concluded that LSSVM and ANFIS algorithms are accurate methods for prediction of Henry’s constant in wide range of chemical structure of compounds in water.

An improved method for Fluctuation Enhanced Sensing (FES) is introduced. We enhanced the old binary fingerprinting method, where the fingerprint bit values were ± 1, by introducing ternary fingerprints utilizing a reference odor. In the ternary method, the fingerprint bit values are -1, 0, and +1 where the 0 value stands for the situation where the slope of the spectrum is identical to that of the reference odor. The application of the reference odor spectrum makes the fingerprint relative to the reference. This feature increases the information entropy of the fingerprints. The method is briefly illustrated by sensing bacterial odor in cow manure isolates.

A novel coronavirus, named 2019-nCoV, is responsible for current epidemic outbreaks in China and also other countries that cause acute pneumonia that was primarily linked to a seafood wholesale market in Wuhan, China. To control and prevent the existing epidemic outbreaks of coronavirus in China, a precise and easy disinfection/sterilization technique is important to disinfect/sterilize the mass-level peoples and their ambient environments (e.g. atmospheric air/aerosols). Among the disinfection techniques, control fire/flame (CF) could be applied. Large-size CF (LSCF) can be generated by using gas burner, gas cylinder that used in restaurant, coals, kerosene (petroleum), dried straws, dried woods) at entry and exit points of big gathering locations (e.g. hospital, airport, rail stations, seaports, apartments, streets/roads, etc. Additionally, small-size CF (SSCF) can be produced by using gas burner of kitchen, electric heater, kindle or waste papers at individual home and ward/room at hospital. Individual person can be soaked/immersed their hands and their belongings nearby CF for a moment, likely followed sterilization during quantification of the number of bacteria in experimental observation, that can rapidly sterilize the person perfectly. Correspondingly, the ambient air/aerosols moved towards CF due to water evaporation by fire that subsequently refresh all ambient air/aerosols by killing all viruses. Such CF could certainly reach the temperature higher than 56 degree C that could effectively disinfect/sterilize/kill the coronavirus. Therefore, CF could be effectively applied to control and prevent the epidemic outbreaks of coronavirus across China and worldwide.

The combination of chemical cross-linking and mass spectrometry is currently a progressive technology for deriving structural information of proteins and protein complexes. In addition, chemical cross-linking is a powerful tool for stabilizing macromolecular complexes for single particle cryo-electron microscopy. Broad pallets of cross-linking chemistry, currently available for the majority of cross-linking experiments, still rely on the amine-reactive N-hydroxysuccinimide esters targeting mainly N-termini and lysine side chains. These cross-linkers are divided into two groups: water soluble and water insoluble; and research teams prefer one or another speculating on the benefits of their choice. However, the effect of cross-linker polarity on the outcome of cross-linking reaction has never been studied. Herein, we use both polar (bis(sulfosuccinimidyl) glutarate) and non-polar (disuccinimidyl glutarate) cross-linkers and systematically investigated the impact of cross-linker hydrophobicity on resulting distance constraints, using bovine serum albumin as a model protein.

Fatty acids (FAs) represent an important class of metabolites, impacting on membrane building blocks and cellular regulatory networks. In nature, prokaryotes are characterized with the most impressing FA structural diversity and the highest relative contents of free fatty acids (FFAs). Thereby, nitrogen-fixing bacteria (order Rhizobiales), often found in symbiosis with legumes, attract a special interest. Indeed, FAs impact on the structure of rhizobial nodulation factors, required for successful infection of plant root. Although the FA patterns can be addressed by GC- and LC-MS, these methods are time-consuming and suffer from compromised sensitivity, low stability of derivatives and artifacts. In contrast, MALDI-TOF-MS represents an excellent platform for high-efficient metabolite fingerprinting, also applicable to FFAs. Therefore, here we propose a simple and straightforward protocol for high-throughput relative quantification of FFAs in rhizobia by the combination of Langmuir technology and MALDI-TOF-MS, which is featured with high sensitivity, accuracy and precision of quantification. Here we propose a step by step procedure comprising rhizobia culturing, pre-cleaning, extraction, sample preparation, mass spectrometric analysis, data processing and post-processing. To demonstrate the analytical potential of the protocol we illustrate it by a case study – comparison the FFA metabolomes of two rhizobia species - Rhizobium leguminosarum and Sinorhizobium meliloti.

The radiosensitivity of biological systems is strongly affected by the system oxygenation. On the nanoscopic scale and molecular level, this effect is considered to be strongly related to the indirect damage of radiation. Even though particle track radiolysis has been the object of several studies, still little is known about the nanoscopic impact of target oxygenation on the radical yields. We present here an extension of the chemical module of the Monte Carlo particle track structure code TRAX, taking into account the presence of dissolved molecular oxygen in the target material. The impact of the target oxygenation level on the chemical track evolution and the yields of all the relevant chemical species is studied in water under different irradiation conditions: different linear energy transfer (LET) values, different oxygenation levels, and different particle types. Especially for low LET radiation, a large production of two highly toxic species (HO₂^• and O₂^•− ), which are not produced in anoxic conditions, is predicted and quantified in oxygenated solutions. The remarkable correlation between the HO₂^• and O₂^•− production yield and the oxygen enhancement ratio observed in biological systems suggests a direct or indirect involvement of HO₂^• and O₂^•− in the oxygen sensitization effect. The results are in agreement with available experimental data and previous computational approaches. An analysis of the oxygen depletion rate in different radiation conditions is also reported.

Edible coating gels developed from the Aloe vera plant have been used as a traditional medicine for about 3000 years. Aloe vera contains 110 potentially active constituents from six different classes: chromone and its glycoside derivatives; anthraquinone and its glycoside derivatives; flavonoids; phenylpropanoids and coumarins; phenylpyrone and phenol derivatives; and phytosterols and others. Apart from medicinal uses, Aloe gels have an important role in food preservation as edible coatings. They provide an edible barrier for atmospheric gases and moisture, and help to reduce the respiration and transpiration of fresh produce, which helps to preserve its postharvest quality. To date, numerous studies have been conducted on the postharvest use of Aloe vera gel. The present review article summarizes and discusses existing available information about the chemical constituents, antimicrobial activity, and food preservative characteristics of Aloe vera.

Alkali-containing submicron particles were measured continuously during three months, including late winter and spring seasons in Gothenburg, Sweden. The overall aims were to characterize the ambient concentrations of combustion-related aerosol particles and to address the importance of local emissions and long-range transport for the atmospheric concentrations in the urban background environment. K and Na concentrations in the PM1 size range were measured by an alkali aerosol mass spectrometer (Alkali-AMS) and a cluster analysis was conducted. Local meteorological conditions and some other data sets were obtained, and back trajectory analyses and chemical transport model (CTM) simulations were included for the evaluation. The Alkali-AMS cluster analysis indicated three major clusters: 1) biomass burning origin, 2) mixture of other combustion sources, and 3) marine origin. Low temperatures and low wind speed conditions correlated with high concentrations of K-containing particles, mainly due to regional emissions from residential biomass combustion; transport of air masses from continental Europe also contribute to cluster 1. The CTM results indicate that open biomass burning in the eastern parts of Europe may have contributed substantially to high PM2.5 concentrations (and to cluster 1) during an episode in late March. According to the CTM results the mixed cluster (2) is likely to include particles emitted from different source types and no single geographical source region seems to dominate for this cluster. The back trajectory analysis and meteorological conditions indicated that the marine origin cluster was correlated with westerly winds and high wind speed; this cluster had high concentrations of Na-containing particles, as expected for sea salt particles.

Background: Reducing the impact of malaria is a key to achieving the sustainable development goals which are geared towards eradicating the disease. The main objective of this study was to synthesize, determine the efficacy and safety of antiplasmodial hybrid drug comprising of sarcosine and aniline derivative for management of plasmodial infections. Results: The hybrid drug was synthesized by adding thionyl chloride to sarcosine in order to form acyl chloride which was then added to aniline to form sarcosine-aniline hybrid molecule. The IC50 of sarcosine-aniline hybrid was 44.80 ± 4.70 ng/ml compared to that of aniline derivative which was 22.86 ± 1.26 ng/ml. The IC50 of control drugs were 2.63 ± 0.38 ng/ml, 5.69 ± 0.39 ng/ml for artesunate and chloroquine respectively. There was a significant difference between IC50 of sarcosine-aniline hybrid and aniline derivative (P<0.05). There was also a significant difference between sarcosine-aniline hybrid and standard drugs used to treat malaria including artesunate and chloroquine (P<0.05). The ED50 of sarcosine-aniline hybrid drug was 6.49mg/kg compared to that of aniline derivative which was 3.61mg/kg. The ED50 of control drugs were 3.56 mg/kg, 2.94mg/kg and 1.78 mg/kg for artesunate-aniline hybrid, artesunate and chloroquine respectively. There was a significant difference (P<0.05) between ED50 of sarcosine-aniline hybrid and both controls such as aniline derivative, artesunate, artesunate-aniline hybrid and chloroquine. Cytotoxicity results revealed that sarcosine-aniline hybrid was safe to vero cells with a CC50 of 50.18±3.53µg/ml. Sarcosine-aniline hybrid was significantly less toxic compared to artesunate, chloroquine and doxorubicin. Sarcosine-aniline hybrid was also safe to mice. Conclusion: Therefore, covalent bitherapy should be used in drug development for drug resistance mitigation.

Different aspects in applying the nucleation theorem to the description of crystallization of liquids are analyzed. It is shown that, by employing the classical Gibbs' approach in the thermodynamic description of heterogeneous systems and assuming that the basic assumptions of classical nucleation theory commonly employed in application to crystallization hold, a general form of the nucleation theorem can be formulated valid not only for one-component but generally for multi-component systems. This result is taken then as the starting point for the derivation of particular forms of this theorem for the cases that the deviation from equilibrium is caused by variations of either composition of the liquid phase, temperature, or pressure. In this procedure, recently developed by us expressions for the curvature dependence of the surface tension, respectively, the dependence of the surface tension on pressure and/or temperature are employed. It is shown that the formulation of the nucleation theorem as proposed by Kashchiev [J. Chem. Phys. 76, 5098-5102 (1982)] holds also for multi-component systems as far as mentioned above assumptions are fulfilled. In the application of classical nucleation theory to crystallization processes it is assumed as one of its basic ingredients that the bulk properties of the critical clusters are widely identical to the properties of the newly evolving crystal phase. This assumption is, however, in general, it is not true. This limitation of the theoretical description can be overcome by the application of the generalized Gibbs approach for the specification of the dependence of the properties of critical crystal clusters on the degree of metastability of the liquid phase. Applying this method, it is demonstrated that a similar formulation of the nucleation theorem as derived based on classical nucleation theory holds true also in cases when a dependence of the state parameters of the critical clusters on the degree of deviation from equilibrium is appropriately accounted for.

An amorphous silicon carbide (SiC) membrane with H2 permeance of 1.2E-7 mol･m^-2･s^-1･Pa^-1 and excellent H₂/CO₂ selectivity of 2600 at 673 K was successfully synthesized on a Ni-gamma-alumina-coated alpha-alumina porous support by counter diffusion chemical vapor deposition (CDCVD) using silacycrobutane (SCB) at 788 K. The dominant permeation mechanism for He and H₂ in the temperature range 323-673 K was activated diffusion. The SiC active layer was formed in Ni-gamma-Al₂O₃ intermediate layer. The thermal expansion coefficients mismatch between SiC active layer and Ni-gamma-Al₂O₃-coated alpha-Al₂O₃ porous support was eased by the low decomposition temperature of SiC source and membrane structure.

The kinetics of biogas production from biomass depends on several factors such as: carbon to nitrogen ratio (C/N), reactor temperature (T), and retention time (RT). The purpose of this study was to obtain a new model for predicting biogas production. Spent Mushroom Compost (SMC) was used to produce biogas in a batch type reactor. The experiments were carried out with different C/N ratios (12.1, 20, 30 and 40) and in both mesophilic (35°C) and thermophilic (55°C) temperatures. The results showed that the Maximum biogas production at 35°C, C/N=20 was equal to 41.9 mL/gVS and 55°C, C/N=30 was equal to 51.6 mL/gVS. By using experimental data, a new kinetic model was proposed to predict biogas production. Comparing the values of the results indicate that the total values of RMSE for Logistics, Gampartz and new kinetic models was 0.1906, 0.1830 and 0.1617, respectively. Therefore, the process of anaerobic digestion of biomass can be assumed to be just a chemical reaction, and the new kinetic model is an appropriate alternative to microbial growth models.

Mammalian cells maintain the complex glycerophospholipid (GPL) class compositions of their various membranes within close limits because this is essential to their well-being or viability. Surprisingly, however it is still not understood how those compositions are maintained except that GPL synthesis and degradation closely coordinated. Here, we hypothesize that abrupt changes in the chemical activity of the individual GPL classes coordinate the synthesis and degradation, as well other homeostatic processes. A previously proposed model proposed that in cellular membranes only a limited number of “allowed” or optimal GPL glass compositions exist because they are energetically more favorable than the other compositions, i.e. they represent local free energy minima (Somerharju et al. 2009). This model, however, could not satisfactorily explain how the optimal compositions are sensed by the key homeostatic enzymes i.e., the rate-limiting synthetizing enzymes and the degrading enzymes (i.e., homeostatic phospholipases). We now propose that when the mole fraction of a GPL class exceeds an optimal one, its chemical activity abruptly increases, which (i) increases its propensity to efflux from the membrane thus making it susceptible for hydrolysis by homeostatic phospholipases, (ii) increases its potency to inhibit its own biosynthesis via a feedback mechanism, (iii) enhances its conversion to another GPL class via a novel process termed “head group remodeling” or (iv) enhances its translocation to other subcellular membranes. Accordingly, abrupt changes in the chemical activity of the individual GPL classes is proposed to regulate and coordinate those four processes maintaining GPL class homeostasis in mammalian cells.

The purpose of this study was to recommend to the government about the appropriate land use based on geoelectric and hydrochemical works. The results were supposed to be used as models for effective land use. During the study, a groundwater survey using a geoelectrical method was conducted and was used to map an aquifer flow. In general, Solok groundwater mapping was meant to provide information necessary to optimize follow-up activities for the use of clean water. It was also intended to minimize the negative impacts of exploitation and utilization of groundwater. This research aimed to provide information on groundwater conditions in Solok. It focused on the survey of groundwater sources, the inversion of measurement data on Sclumberger electrode configuration geoelectric in thirteen districts, and chemical analysis of pH, Fe, Nitrite, and DHL. The results show there was a great potential for groundwater-unconfined aquifers.

Adaptive radiations occur mostly in response to environmental variation through the evolution of key eco-morphological innovations that allow emerging species to occupy new ecological niches. However, rapid phenotypic evolution and the evolution of key novelties are likely to also occur when a couple or few species are engaged into narrow ecological interactions. To demonstrate coevolution is a difficult task; only elusive evidences confirm that coevolution is a driver of speciation and diversification. Here we propose that the adaptive radiation of the Mediterranean orchid genus Ophrys, which gave rise to ca. 350 species since the apparition of the genus is due to the particular co-evolutionary dynamics between these plants and their pollinators. We suggest that the pollination by sexual swindle used by Ophrys orchids is the main driver of this coevolution. Flowers of each Ophrys species mimic sexually receptive females of one particular insect species, mainly bees. Male bees are attracted by pseudo-pheromones emitted by Ophrys flowers that are similar to the sexual pheromones of their females. Males lured by the flower shape, color and hairiness attempt to copulate with the flower, which glues pollen on their bodies. Pollen is eventually transferred to the stigma of another flower of the same Ophrys species during similar copulation attempts. Three observations led us to propose the scenario of an asymmetric co-evolutionary relationship between Ophrys and their pollinators. Firstly, there is a strong intra-specific competition among Ophrys individuals for the attraction of their species-specific pollinators, which is due to the high learning and memorization abilities of bees that record the pheromone signatures of kin or of previously courted partner to avoid (further) copulation attempts. Mnemonic pollinators induce thus a strong selective pressure for variation in the pseudo-pheromones emitted by individual flowers, which will potentially generate shifts in pollinator species, and hence Ophrys speciation. These pollinator shifts are adaptive for new Ophrys species because they may benefit from a competitor-free space. Secondly, such shifts in pollinator species are due to the random crossing of peaks in the olfactory landscape of the pollinator guild that is syntopic to each particular Ophrys population. This selective process on individual, random variation in pseudo-pheromone bouquets is followed by directional selection on flower phenotypes that will reinforce the attraction of the new pollinator. Thirdly, pollinators use the pseudo-pheromones emitted by Ophrys to locate suitable habitats from a distance within complex landscapes. Pollinators stay fixed for a while in these habitats by the local diversity of pseudo-pheromones, which increases their probability of encounter with a receptive female and hence the reproduction probability of both sexes. Conversely, pollinators disperse out of small suitable habitats once they have memorized the local diversity of sexual pseudo-pheromone bouquet or if fecundated Ophrys flowers repel pollinators, which decreases the probability of geitonogamy (plant advantage) but limit pollinator mating with locally emergent insect females, thus limiting inbreeding and favoring gene flow (pollinator advantage). Finally, we propose several research avenues that emerged according to this scenario of adaptive radiation by assymetric coevolution between Ophrys species and their pollinators.

The use of biodiesel fuels in compression ignition engines leads to decrease CO, PM, HC and smoke opacity. However, NOx emissions increase importantly. Various methods to reduce NOx are used namely the EGR, the water injection method and the steam injection method. In this study, the steam injection method has been used instead of the other methods because of its benefits. This study examines the effects of steam injection on combustion products of diesel and biodiesel fuels by considering chemical equilibrium in order to determine the equilibrium combustion products involving 10 combustion products. A developed simulation code determing the equilibrium mole fractions and thermodynamic properties of combustion products is used for diesel and biodiesel fuels. It can be used for any fuel consisting of carbon, hydrogen or any oxygenated fuel. The results show that the mole fraction of CO2 and CO decrease with the steam injection ratios. NO mole fractions decrease with steam injection for lean mixtures but they increase slightly in the case of rich mixtures. The specific heat of combustion products increase with the steam injection ratios. Thus, the engine performance can be improved using the method. The model has been validated by comparing model results with the ones of NASA CEA software and GASEQ software using the methane as fuel. The relative errors of equilibrium mole fractions and thermodynamic properties of combustion products are less than 0.98 %.

The slate aggregate has long been perceived as a substandard, low quality waste material with its physical and chemical properties not being competitive with those of the primary aggregates. It is assumed that the slate aggregate particles are not strong, that is not durable and will not compact. This research aims to address those claims and review the available literature on the performance of the slate aggregate. The review inaugurates by analysing the physical, chemical and mechanical properties of slate, before expanding into a literature review of laboratory testing’s on the effect of moisture content on density, compaction and layer thickness of slate aggregate.The paper reviews case studies of construction projects in North Wales, where the slate aggregate has been used for general fill and road building for many years. Some of the case studies include the A55 coastal road and duelling of the A5 in Anglesey (WRAP, 2004), where slate aggregate was successfully used as sub-base. The paper also investigates why many civil engineers are reluctant to use the slate aggregate and regard the material as sub-standard, flaky aggregate. The research paper reviews the potential usages and various products the slate aggregate is suitable for and satisfies the requested standards. The final topic reviewed is the cost of transporting slate aggregate compared with the cost of transport for primary aggregate and the introduction of the Primary Aggregates Tax (Parliament of the United Kingdom, 2011). The last topic includes a critical analyses of the claims that the slate aggregate a commercially viable construction material despite its remote location (Woodward et al, 2004). The transportation cost and the supply chain complexities must be evaluated prior to considering the long-term sustainability of the product (Radanliev et al^1-6, 2014, 2015, 2016).

A portable urea sensor for use in the fast flow condition was fabricated using porous polytetrafluoroethylene (PTFE) membranes coated with amine-functionalized parylene, parylene-A, by vapor deposition. To generate a specific electrochemical sensor signal from urea, the urea-hydrolyzing enzyme urease was immobilized on the parylene-A-coated PTFE membranes via chemical crosslinking using glutaraldehyde. The urease-immobilized membranes were assembled in a polydimethylsiloxane (PDMS) fluidic chamber, and a screen-printed carbon three-electrode system was used for electrochemical measurements. The success of urease immobilization was confirmed using fluorescence microscopy, scanning electron microscopy, and Fourier-transform infrared spectroscopy. The optimum concentration of urease for immobilization on the parylene-A-coated PTFE membranes was determined to be 48 mg/mL, and the optimum number of membranes in the PDMS chamber was found to be 8. Using these optimized conditions, we fabricated the urea biosensor and monitored urea samples under various flow rates ranging from 0.5 to 10 mL/min in the flow condition using chronoamperometry. To test the applicability of the sensor for physiological samples, we used it for monitoring urea concentration in the waste peritoneal dialysate of a patient with chronic renal failure, at a flow rate of 0.5 mL/min.

Heavy metals and organic pollutants are ubiquitous environmental pollutants affecting the quality of soil, water and air. Over the past 5 decades, many strategies have been developed for the remediation of polluted water. Strategies involving aquatic plant use are preferable to conventional methods. In this study, an attempt was made to provide a brief review on recent progresses in research and practical applications of phytoremediation for water resources with the following objectives: (1) to discuss the toxicity of toxic chemicals pollution in water to plant, animals and human health (2) to summarise the physicochemical factors affecting removal of toxic chemicals such as heavy metals and organic contaminants in aqueous solutions by aquatic plants; (3) to summarise and compare the removal rates of heavy metals and organic contaminants in aqueous solutions by diverse aquatic plants; and (4) to summarise chemometric models for testing aquatic plant performance. More than 20 aquatic plants specie have been used extensively while duckweed (L. minor), water hyacinth (Eichhornia crassipes), water lettuce (P. stratiotes) are the most common. Overall, chemometrics for performance assessment reported include: Growth rate (GR), Growth rate inhibition (% Inhibition), Metal uptake (MU), translocation/transfer factor (TF), bioconcentration factor (BCF), Percent metal uptake (% MU), Removal capacity (RC) and Tolerance index (TI) while absorption rate have been studied using the sorption kinetics and isotherms models such as pseudo-first-order (PFO), pseudo-second-order (PSO), Freundlich, Langmuir and Temkin. Using modeling and interpretation of adsorption isotherms for performance assessment is particularly good and increases level of accuracy obtained from adsorption processes of contaminant on plant. Conclusion was drawn by highlighting the gap in knowledge and suggesting key future areas of research for scientists and policymakers.

The ability to predict the skin sensitization potential of small organic molecules is of high importance to the development and safe application of cosmetics, drugs and pesticides. One of the most widely accepted methods for predicting this hazard is the rodent local lymph node assay (LLNA). The goal of this work was to develop in silico models for the prediction of the skin sensitization potential of small molecules that go beyond the state of the art, with larger LLNA data sets and, most importantly, a robust and intuitive definition of the applicability domain, paired with additional indicators of the reliability of predictions. We explored a large variety of molecular descriptors and fingerprints in combination with random forest and support vector machine classifiers. The most suitable models were tested on holdout data, on which they yielded competitive performance (Matthews correlation coefficients up to 0.52; accuracies up to 0.76; areas under the receiver operating characteristic curves up to 0.83). The most favorable models are available via a public web service at https://nerdd.zbh.uni-hamburg.de/skinDoctor/ that, in addition to predictions, provides assessments of the applicability domain and indicators of the reliability of the individual predictions.

Quasicrystals are a class of ordered solids made of typical metallic atoms but they do not exhibit the physical properties usually signaling the presence of metallic bonding and their electrical and thermal transport properties resemble a more semiconductor-like than metallic character. In this paper I first review a number of experimental results and numerical simulations suggesting that the origin of the unusual properties of these compounds can be traced back to two main features. For one thing, we have the formation of covalent bonds among certain atoms grouped into clusters at a local scale. Thus, the nature of chemical bonding among certain constituent atoms should play a significant role in the onset of non-metallic physical properties of quasicrystals bearing transition-metal elements. On the other hand, the self-similar symmetry of the underlying structure gives rise to the presence of an extended chemical bonding network due to a hierarchical nesting of clusters. This novel structural design leads to the existence of quite diverse wave functions, whose transmission characteristics range from extended to almost localized ones. Finally, the potential of quasicrystals as thermoelectric materials is discussed on the basis of their specific transport properties.

White and three types of black garlic (13, 32 and 45 days of fermentation, named 0C1, 1C2 and 2C1 respectively) were selected in order to check possible differences in their nutraceutic potential. For this purpose, garlic were physico-chemically characterised, and both in vivo and in vitro assays were carried out. Black garlic showed higher polyphenol content and antioxidant capacity than white garlic. The biological studies have shown that only white garlic was not safe showing toxicity effect. Furthermore, none garlic exert protective effects against H₂O₂, except the 0C1 black garlic. Moreover, garlic was non-genotoxic with the exception of the highest concentration of white garlic. On the other hand, 0C1 was the most antigenotoxic substance. The in vivo longevity assays yielded significant extension of lifespan results in some concentrations of white and 0C1and 1C2 black garlic. The in vitro experiments showed that all studied garlic induced a decrease in leukaemia cells growth. However, none type of garlic was able to induce proapoptotic internucleosomal DNA fragmentation. Taking into account the physicochemical and biological data, black garlic could be considered as a potential functional food and used in preventive treatment of age-related diseases. In addition, our findings could be relevant for the black garlic processing agrifood companies as the economical and timing costs are significantly reduced to 13 days aging.

Food preservatives are compound that are used for the treatment of food to improve the shelf life. In the food industry, is necessary to monitor all processes, for both safety and quality of the product. An electronic nose (or e-nose) is a biomimetic olfactory system that could find numerous industrial applications, including food quality control. Commercial electronic noses are based on sensor arrays composed by a combination of different sensors, which include conductometric metal oxide devices. Metal oxide nanowires are considered among the most promising materials for the fabrication of novel sensing devices, which can enhance the overall performances of e-noses in food applications. In the present work, is reported the fabrication of a novel sensor array based on SnO2, CuO and WO₃ nanowires deposited on top of commercial μHPs, provided by ams Sensor Solutions Germany GmbH. The array was tested for the discrimination of four typical compounds added to food products or used for their treatment to increase the shelf life: ethanol, acetone, nitrogen dioxide and ozone. Results are very promising: the sensors array was able to operate for long time consuming less than 50mW for each single sensor, and PCA analysis confirms that the device was able to discriminate between different compounds.

In extant biology, biopolymers perform multiple crucial functions. The biopolymers are synthesized by enzyme-controlled biosystems that would not have been available at the earliest stages of chemical evolution and consist of correctly sequenced and/or linked monomers. Some of the abiotic “messy” polymers approximate some functions of biopolymers. Condensation polymers are an attractive search target for abiotic functional polymers since principal polymers of life are produced by condensation and since condensation allows for the accurate construction of high polymers. Herein the formation of hyperbranched polyesters that have been previously used in the construction of enzyme-like catalytic complexes is explored. The experimental setup compares between the branched polyesters prepared under mild continuous heating and the wet-dry cycle conditions. The results reveal that period wetting during which partial hydrolysis of the polyester occurs, helps control the chain growth and retards the gel transition. It is significant to the origin of life studies that environmental, prebiotically plausible conditions could achieve such control without enzymes or a skilled chemist. As expected in marginally controlled systems, the identification of each component of the heterogeneous system has proved challenging, but it is not crucial for drawing the conclusions.

The current study focused on reviewing the rapid growing of using magnetic water in different fields of science and measure the influence of several intensities of magnetization on the chemical and electrical properties of tap water treated by reverse osmosis. The work includes circulation of water for 24 h. in magnetic fields of intensity 500, 1000, 1500, and 2000 G. The magnetization of water causes increasing some positive and negative ions in water such as (Mg, K, Na, Cl¯, Alkaline and SiO₂) and decreasing some positive and negative ions (Ca and SO₃). In the near future, the application of concepts of sustainability development in civil engineering have the to produce structures in harmony with these concepts through using of high-performance materials with less impacts on the environmental and have low cost. The main application of using magnetic water is improvement the geotechnical properties of soil through precipitation of calcite which increases the bond between soil particles and then strength of soil.

Cornea severe inflammation produces opacity or even perforation, scarring, and angiogenesis, resulting in blindness. The cornea can be used to study the effect of new anti-angiogenic chemopreventive agents. We researched the anti-angiogenic effect of two extracts, Methanol (Met) and Hexane (Hex), from the seed of Cucurbita argyrosperma, in the inflamed corneas. The corneas of Wistar rats were alkali-injured and treated intragastrically for seven successive days. Clinical manifestation as opacity score, corneal neovascularization (CNV) area, re-epithelialization percentage, and histological evaluation were performed. Inflammatory (COX-2, NF-κB, and IL-1β), and angiogenic (VEGF-A, VEGFR1, VEGFR2) markers were assessed by immunohistochemistry. Cox-2, Il-1β, and Vegf-a mRNA levels were also determined. After treatments, we observed slim corneal thickness with lower opacity scores and low cell infiltration compared to untreated rats. Treatment also accelerated wound healing and decreased CNV area. The staining of inflammatory and angiogenic factors was significantly decreased. These effects are related to a down-expression of Cox-2, Il-1β, and Vegf. These results suggest that intake of C. argyrosperma seed can be used to attenuate the angiogenesis secondary to inflammation in corneal chemical damage.

Cyanobacteria are photosynthetic microorganisms that colonize diverse environments worldwide, ranging from ocean to freshwaters, soils, and extreme environments. Their adaptation capacities and the diversity of natural products (molecules, metabolites, or compounds) that they synthesize support the cyanobacterial success for the colonization of their respective ecological niches. Although cyanobacteria are well-known for their toxin production and their relative deleterious consequences, they also produce a large variety of molecules that exhibit beneficial properties with high potential for various fields of application (e.g., synthetic analog of the dolastatin 10 used against Hodgkin lymphoma). The present review specially focuses on the beneficial activities of cyanobacterial molecules described so far. Based on an analysis of 670 papers, it appears that more than 90 genera of cyanobacteria have been found to produce compounds with potential beneficial activities, most of them belonging to the orders Oscillatoriales, Nostocales Chroococcales, and Synechococcales. The rest of the cyanobacterial orders (i.e., Pleurocapsales, Chroococcidiopsales, and Gloeobacterales) remain poorly explored in terms of their molecular diversity and relative bioactivity. The diverse cyanobacterial molecules presenting beneficial bioactivities belong to 10 different chemical classes (alkaloids, depsipeptides, lipopeptides, macrolides/lactones, peptides, terpenes, polysaccharides, lipids, polyketides, and others) that exhibit 14 major kinds of bioactivity. However, no direct relation between the chemical class and the bioactivity of these molecules has been demonstrated. We further selected and specifically described 50 molecule families according to their specific bioactivities and their potential uses in pharmacology, cosmetology, agriculture, or other specific fields of interest. This up-to-date review takes advantage of the recent progresses in genome sequencing and biosynthetic pathway elucidation, and presents new perspectives for the rational discovery of new cyanobacterial metabolites with beneficial bioactivity.