Aerated concrete, which is manufactured from binding material, sand, foaming agent and water, is currently being utilized in the construction industry because of its lightweight and durability. The binding material, cement, along with other materials used in the concrete produces huge carbon footprints during its fabrication. The utilization of natural aggregates name as coarse aggregates depletes the natural resources of the country. Therefore, huge amounts of agricultural wastes have led scholars to investigate the effectiveness of replacing conventional materials used in concrete with agricultural wastes. In the current study, rice husk ash (RHA) was used as supplementary cementing material, thereby reducing the amount of cement used in aerated concrete (AC) mixture will reduce carbon footprints. The experimental and numerical analysis were conducted to investigate structural behavior of reinforced RAC- B beams subjected to flexural load. Parametric study on structural performance of RAC- B beam under flexure were conducted using finite element analysis (FEA). From the experiment and FEA. Results from the parametric study showed that RAC-10%RHA-B with higher depth structurally performed better compared to RAC-B under flexure with greater load carrying capacity, lesser maximum deflection, and less cracks developing in the tension area.

Nine variants of regular lattice structures with different relative densities have been designed and successfully manufactured. The produced structures have been subjected to geometrical quality control, and the manufacturability of the implemented selective laser melting SLM technique has been assessed. It was found that the dimensions of the produced lattice struts differ from those of the designed struts. These deviations depend on the direction of geometrical evaluation. Additionally, the microstructures and phase compositions of the obtained structures were characterized and compared with those of conventionally produced 316L stainless steel. The microstructure analysis and X-Ray Diffraction XRD patterns revealed a single austenite phase in the SLM samples. Both a certain broadening and a displacement of the austenite peaks were observed due to residual stresses and a crystallographic texture induced by the SLM process. Furthermore, the mechanical behavior of the lattice structure material has been defined. It was demonstrated that under both quasi-static and dynamic testing, lattice structures with high relative densities are stretch-dominated, whereas those with low relative densities are bending-dominated. Moreover, the linear relationship between the energy absorption and relative density under dynamic loading conditions has been defined

The Sei Dareh Bridge is a cable-stayed bridge located in West Sumatra Province, Indonesia. The bridge, has a main span of 123 meters length and 9 meters wide, crosses the Batanghari River. Traffic load is transmitted through 4 prestressed cables to a 42.4 meter high pylon made of concrete. Bridge deck and traffic loads are directly supported by steel box girders as main beams that are reinforced laterally with cross beams IWF 800.300.16.24 and stringers IWF 350.350.12.19. This paper discusses static and dynamic testing on the bridge which aims to assess the feasibility before it is opened for public. Based on the test, it was concluded that the 73% static load could not be achieved because the deflection that occurred was beyond the allowable deflection. This is exacerbated by the sound of a loud clanging sound on the ST2-X1 prestressed cable when loading to 240 tons or 58% of the targeted load. In addition, this bridge is included in the "lazy bridge" category because it takes 24 hours to return to an undeformed condition after loading. As a recommendation for this bridge, it is necessary to carry out a structural health monitoring system (SHMS) regularly on the vehicle floor and cables.

Understanding the shoulder-specific load in handball is important for both prevention and rehabilitation of shoulder injuries. The shoulder-specific load is largely a result of the number and speed of throws. However, it is difficult to quantify number and speed of throws in handball due to limitations in the current technology. Therefore, the purpose of this study was to develop a novel method to estimate throwing speed in handball using a low-cost accelerometer-based device. Nineteen experienced handball players each performed 25 throws of varying types while we measured the acceleration of the wrist using the accelerometer and the throwing speed using 3D motion capture. Using cross-validation, we developed four prediction models using combinations of the logarithm of the peak total acceleration, sex and throwing type as the predictor and the throwing speed as the outcome. We found that all models were well-calibrated (mean calibration of all models: 0.0 m/s, calibration slope range: 0.99-1.00) and precise (R2 = 0.71-0.85, mean absolute error = 1.32-1.82 m/s). We conclude that the developed method appear to provide practitioners and researchers with a feasible and cheap method to estimate throwing speeds in handball.

This work aims to investigate the influence of reaction time and catalyst-to-residual fat ratio by catalytic upgrading from pyrolysis vapors of residual fat at 400 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, and acid value) and chemical composition of bio-oils, over a catalyst fixed bed reactor of activated carbon pellets impregnated with 10.0 M NaOH, in semi pilot scale. The experiments were carried out at 400 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 50, 60, 70, 80, 90, 100 and 120 minutes in order to investigate the process kinetics. The physicochemical properties (density, kinematic viscosity, and acid value) of bio-oils were determined by official methods. The chemical composition of bio-oils determined by GC-MS. The thermal catalytic cracking of residual fat show bio-oils yields from 55.55 to 30.22 (wt.%), aqueous phase yields between 2.83 and 3.19 (wt.%), solid phase yields between 13.56 and 9.75 (wt.%), and gas yields from 27.89 to 55.60 (wt.%). The yields of bio-oil decreases from 74.41 to 30.22% (wt.) with increasing catalyst-to-Tallow kernel oil ratio, while that of gaseous phase increases from 12.87 to 55.60% (wt.). For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of bio-oils decreases as the reaction time increases varying from 0.9266 to 0.8220 g/cm³, 8.10 to 2.24 mm²/s, and 144.14 to 2.37 mg KOH/g. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, ring-containing alkanes, ring-containing alkenes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the pyrolysis and catalytic cracking experiments, the hydrocarbon selectivity in bio-oil increases with increasing reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties density, kinematic viscosity, and acid value were 0.8220 g/cm³, 3.03 mm2/s, and 2.37 mg KOH/g, respectively, with a maximum hydrocarbon concentration of 97.194% (area.) and 2.806% ketones (area.) were obtained at 400 °C and 1.0 atmosphere, 80 minutes, without catalyst. For the catalytic cracking experiments, the maximum hydrocarbon content of 75.763% (area.) and 17.041% (area.) carboxylic acids, 4.702% (area.) ketones (area.), and 2.494% (area.) non-identified oxygenates was obtained at 400 °C and 1.0 atmosphere, 90 minutes, using a catalyst fixed bed reactor, with 10.0% (wt.) activated carbon pellets impregnated with 10.0 M NaOH as catalyst.

Commercial buildings are a significant consumer of energy worldwide. Logistics facilities, and specifically warehouses, are a common building type yet under-researched in the demand-side energy forecasting literature. Warehouses have an idiosyncratic profile when compared to other commercial and industrial buildings with a significant reliance on a small number of energy systems. As such, warehouse owners and operators are increasingly entering in to energy performance contracts with energy service companies (ESCOs) to minimise environmental impact, reduce costs, and improve competitiveness. ESCOs and warehouse owners and operators require accurate forecasts of their energy consumption so that precautionary and mitigation measures can be taken. This paper explores the performance of three machine learning models (Support Vector Regression (SVR), Random Forest, and Extreme Gradient Boosting (XGBoost)), three deep learning models (Recurrent Neural Networks (RNN), Long Short-Term Memory (LSTM), and Gated Recurrent Unit (GRU)), and a classical time series model, Autoregressive Integrated Moving Average (ARIMA) for predicting daily energy consumption. The dataset comprises 8,040 records generated over an 11-month period from January to November 2020 from a non-refrigerated logistics facility located in Ireland. The grid search method was used to identify the best configurations for each model. The proposed XGBoost models outperform other models for both very short load forecasting (VSTLF) and short term load forecasting (STLF); the ARIMA model performed the worst.

Many combinatorial optimization problems are hard to solve within the polynomial computational time or NP-hard problems. Therefore, developing new optimization techniques or improving existing ones still grab attention. This paper presents an improved variant of the Ant Colony Optimization meta-heuristic called Enhanced Hyper Cube Framework ACO (EHCFACO). This variant has an enhanced exploitation feature that works through two added local search movements of insertion and bit flip. In order to examine the performance of the improved meta-heuristic, a well-known structural optimization problem of laminate Stacking Sequence Design (SSD) for maximizing critical buckling load has been used. Furthermore, five different ACO variants were concisely presented and implemented to solve the same optimization problem. The performance assessment results reveal that EHCFACO outperforms the other ACO variants and produces a cost-effective solution with considerable quality.

In cross-country skiing the time difference between a race winner and the person coming second is typically very small. Since much of the energy is spent on overcoming resistive forces, a relatively small reduction of these can have a significant impact on the results. The resistive forces come partly from the friction in the tribological interface, between the ski and the snow, and as with many tribological applications the characterisation of its origin, plays an important role in determining the frictional properties. Also in cross-country ski friction, there are several scales impacting the frictional performance, with the major contributors being the ski-camber profile and ski-base structure. Macro-scale measurements of the ski's camber profile under load, are often used to determine how adequate the ski is for a specific condition. The characteristic properties usually obtained are, the force required to collapse the ski to a certain camber height, the topography of the kick-wax zone, and by simple means a determined lengths of the frictional interface, i.e., the apparent contact length. To this date, there are some mathematical models, but there is no robust way of determining the macro-scale contact properties between a cross-country ski and a counter surface using simulations. In the present paper an Artificial neural networks (ANN) is trained to predict the ski-camber profile for various loads placed at different positions, and a well established deterministic approach is used to simulate the contact between the ANN-predicted ski-camber profile and a linearly elastic body with a flat surface, representing the snow. The results suggest that this method is feasible for the determination of the apparent contact characteristics of different skis. Moreover, we show that the apparent contact area does not linearly depend on the load, and that the elastic properties of the counter surface also has a large impact on the apparent contact area and the average apparent contact pressure.

Internet of things (IoT) is a network of smart things. This indicates the ability of these physical things to transfer information with other physical things. The characteristics of these networks, such as topology dynamicity and energy constraint, challenges the routing problem in these networks. Previous routing methods could not achieve the required performance in this type of network. Therefore, developers of this network designed and developed specific methods in order to satisfy the requirements of these networks. One of the routing methods is utilization of multipath protocols which send data to its destination using routes with separate links. One of such protocols is RPL routing protocol. In this paper, this method is improved using composite metrics which chooses the best paths used for separate routes to send packets. We propose Energy and Load aware RPL (ELaM-IoT) protocol, which is an enhancement of RPL protocol. It uses a composite metric, calculated based on remaining energy, hop count, Link Expiration Time (LET), load and battery depletion index (BDI) for the route selection. In order to evaluate and report the results, the proposed ELaM-IoT method is compared to the ERGID and ADRM-IoT approaches with regard to average remaining energy, and network lifetime. The results demonstrate the superior performance of the proposed ELaM-IoT compared to the ERGID and ADRM-IoT approaches.

The area of Central and Eastern Europe, and thus Poland, is not exposed to effects of seismic actions. Any possible tremors can be caused by coal or copper mining. Wind, rheological effects, the impact of other objects or a non-uniform substrate are the predominant types of loading included in calculations for stiffening walls. The majority of buildings in Poland, as in most other European countries, are low, medium-high brick buildings. Some traditional materials, like solid brick (>10% of construction materials market) are still used. But autoclaved aerated concrete (AAC) and cement-sand calcium-silicate (Ca-Si) elements with thin joints are prevailing (>70% of the market) on the Polish market. Adding reinforcement only to bed joints in a wall is a satisfactory solution (in addition to confining) for seismic actions occurring in Poland that improves ULS and SLS. This paper presents results from our own tests on testing horizontal shear walls without reinforcement and with different types of reinforcement. This discussion includes 51 walls made of solid brick (CB) reinforced with steel bars and steel trusses, results from tests on 15 walls made of calcium-silicate (Ca-Si) and AAC masonry units reinforced with steel trusses and plastic meshes. Taking into account our own tests and those conducted by other authors, empirical relationships were determined on the basis of more than 90 walls. They are applicable to design and construction phase to determine the likely effect of reinforcement on cracking stress that damage shear deformation and wall stiffness.

Due to the rapid development and popularity of the Internet, cloud computing has become an indispensable application service. However, how to assign various tasks to the appropriate service nodes is an important issue. Based on the reason above, an efficient scheduling algorithm is necessary to enhance the performance of system. Therefore, a Three-Layer Cloud Dispatching (TLCD) architecture is proposed to enhance the performance of task scheduling. In first layer, the tasks need to be distinguished to different types by their characters. Subsequently, the Cluster Selection Algorithm is proposed to dispatch the task to appropriately service cluster in the secondly layer. Besides, a new scheduling algorithm is proposed to dispatch the task to a suitable server in a server cluster to improve the dispatching efficiency in the thirdly layer. Basically, the TLCD architecture can obtain better task completion time than previous works. Besides, our algorithm and can achieve load-balancing and reliability in cloud computing network.

This paper reports a new control strategy to improve sharing of unbalanced currents in islanded LV microgrids. This technique provides fast and effective sharing of positive-, negative- and zero-sequence currents, and is the first example of zero-sequence current sharing in the literature. The controllers are designed in the stationary frame. The control structure consists of four loops; 1)~the current controller; 2)~the voltage controller; 3)~the droop controller and the 4)~negative and zero sequence current controllers. The output current is considered unknown for the controller and is added to the control system as a disturbance. The proposed controller features a high gain in fundamental and harmonic frequencies, hence a good voltage quality is obtained in the presence of unbalanced and nonlinear loads. To this aim, a proportional-resonant (PR) controller is adopted as the current controller. By using a multi-resonant controller as current controller, a unified control structure is obtained which is suitable for both grid-connected and islanded modes. The voltage controller is designed using a resonant controller so that the voltage can have low VUF and THD in the presence of unbalanced and nonlinear loads. Furthermore, in this paper droop method is applied to the control structure to share real and reactive powers. Simulation studies show that the conventional droop method cannot share the oscillatory part of the output power that is due to the presence of unbalanced loads in the microgrid. This paper relies on using zero and negative sequence virtual impedance controller to share the oscillatory part of output power. By using zero-sequence virtual impedance controller (ZSVIC) and negative-sequence virtual impedance controller (NSVIC), the zero and negative sequence currents in the microgrid are controlled and shared effectively. By compensating zero- and negative-sequence currents locally, the flow of these currents in the microgrid is minimized, and the overall power quality of the islanded LV microgrid is improved.

The present study shows a methodology for analyzing and designing a cylindrical packed-bed reactor considering stationary and dynamic models. The design comprises the reactor's stationary and dynamic governing differential equations for mass and heat transfer under multi-dimensional approaches. The results included simulation of concentration, temperature, and reaction rate profiles via the 1-D and 2-D differential equations solution with FlexPDE software. The analysis was complemented with a scaled 3-D dynamic model implemented in COMSOL Multiphysics. Both FlexPDE and COMSOL Multiphysics relied on the finite element technique to solve the governing differential equations. The simulated concentration and temperature profiles from both FlexPDE and COMSOL models were compared to experimental data gathered from literature (specifically from a Fischer-Tropsch process to produce low-molecular-weight hydrocarbons in a configuration of cylindrical packed-bed reactors). Simulated concentration and temperature profiles from the 2-dimensional dynamic model and the COMSOL model were in good agreement with the trend observed in experimental data. Finally, the predicted reaction rate profiles from the COMSOL model and the 2-dimensional dynamic model followed the temperature trend, thus reflecting the temperature dependence of the reaction.

Sediment plumes, released to the Bering Sea from the delta front of the Yukon River, Alaska, are initiated mainly by glacier-melt sediment runoffs in the glacierized regions of the Yukon River drainage basin. The surface sediment plumes are extended around the fan-shaped Yukon River delta, which is followed by the northwestward dispersion. During continuous measure-ments of the Yukon River discharge and sediment load, behaviors of the sediment plumes were explored by shipboard observations in the Bering Sea offshore from the Yukon delta. At the high river sediment load of ca. 3000 kg/s, the plume partially plunged into the sea bottom layer. The plunging probably originated in the nepheloid-layer formation from the flocculation of river-suspended sediment, of which more than 90 %wt. is silt and clay (grain size d < 0.063 mm). In order to numerically obtain the area of the surface sediment plumes, a satellite image analy-sis was performed by using three near-infrared bands in MODIS/Aqua or MODIS/Terra. The plume area was significantly correlated (R2=0.735, p<0.01) to the sediment load averaged for the two days with time lags of 20 days and 21 days to the date of a certain satellite image. Hence, the dispersion of plume-suspended sediment appears to be controlled by the sediment runoff events in the Yukon River rather than the northward “Alaskan Coastal Water”.

Based on the two-node Euler-Bernoulli beam, the tower system is discretized by finite element method, and the cubic Hermite polynomial is taken as the shape function of the beam element, and the structural characteristic matrix of the tower system is calculated, and the wind turbine-nacelle-tower multi-degree of freedom is established Finite element numerical model. The aerodynamic load calculation formula for any nacelle attitude angle is deduced. The influence of the vibration feedback of the flexible tower on the aerodynamic load of the wind turbine is studied. The results show that when the rigidity of the tower is large, the impact of tower vibration feedback on the aeroelastic load of the wind turbine is small. For a tower system with greater flexibility, the time-varying feedback of wind-induced vibration will cause greater aeroelastic load changes, especially the overturning moment of the tower top, which will cause a greater impact on the dynamic behavior of the tower in the downwind and crosswind directions. As the flexibility of the tower system increases, the interaction between tower vibration and aerodynamic load is gradually increasing. Taking the impact of the flexible tower on the aeroelastic load of the wind turbine into account, on the one hand, helps to predict the wind more accurately. The aerodynamic load of the wind turbine improves the efficiency of wind energy utilization. On the other hand, it can more accurately analyze the dynamic behavior of the flexible structure of the wind turbine, which is extremely beneficial to the structural optimization design of the wind turbine.

Dynamic visualizations have been developed to exchange information that transforms over time across a broad range of professional and academic contexts. However, these visual tools may impose substantial demands on the learner’s cognitive resources that are very limited in current knowledge. Cognitive load theory has been used to improve learning from dynamic visualizations by providing certain design techniques to manage learner cognitive load without adding any oral/written explanations. This systematic review examined a series of experimental studies assessing the roles of these design techniques in learning tactical scenes of play through dynamic visualizations. Electronic databases PubMed and Google Scholar were used to search relevant articles. Eleven studies were eventually included for the systematic review based on the eligibility criteria. The present review revealed that adapting design techniques to the level of learners’ expertise, type of depicted knowledge, and level of content complexity is a crucial part of effective learning.

The tiered laboratory framework for HIV viral load monitoring accommodates a range of HIV viral load testing platforms, with quality assessment critical to ensure quality patient testing. HIV plasma viral load testing is challenged by the instability of viral RNA. An approach using an RNA stabilizing buffer is described for the Xpert® HIV-1 Viral Load (Cepheid) assay and was tested in remote laboratories in South Africa. EDTA-plasma panels with known HIV viral titres were prepared in PrimeStore molecular transport medium for per-module verification and per-instrument external quality assessment. The panels were transported at ambient temperatures to 13 testing laboratories during 2017 and 2018, tested according to standard procedures and uploaded to a web portal for analysis. A total of 275 quality assessment specimens (57 verification panels and two EQA cycles) were tested. All participating laboratories met study verification criteria (n=171 specimens) with an overall concordance correlation coefficient (ρ_c) of 0.997 (95% confidence interval [CI]: 0.996 to 0.998) and a mean bias of -0.019 log cp/mL (95% CI: -0.044 to 0.063). The overall EQA ρ_c (n=104 specimens) was 0.999 (95% CI: 0.998 to 0.999), with a mean bias of 0.03 log cp/mL (95% CI: 0.02 to 0.05). These panels are suitable for use in quality monitoring of Xpert® HIV-1 VL and are applicable to laboratories in remote settings.

Powder bed fusion (PBF) process is a metal additive manufacturing process which can build parts with any complexity from a wide range of metallic materials. PBF process research has predominantly focused on the impact of only a few parameters on product properties due to the lack of a systematic approach for optimizing a large set of process parameters simultaneously. The pivotal challenges regarding this process require a quantitative approach for mapping the material properties and process parameters onto the ultimate quality; this will then enable the optimization of those parameters. In this study, we propose a two-phase framework for optimizing the process parameters and developing a predictive model for 316L stainless steel material. We also discuss the correlation between process parameters -- i.e., laser specifications -- and mechanical properties and how to achieve parts with high density (> 98%) as well as better ultimate mechanical properties. In this paper, we introduce and test an innovative approach for developing AM predictive models, with a relatively low error percentage of 10.236% that are used to optimize process parameters in accordance with user or manufacturer requirements. These models use support vector regression, random forest regression, and neural network techniques. It is shown that the intelligent selection of process parameters using these models can achieve an optimized density of up to 99.31% with uniform microstructure, which improves hardness, impact strength, and other mechanical properties.

This study aims to improve the shaft with hexagon joints to be a type not requiring welding or bolts in the static load test . In order to evaluate the bearing capacity of helical piles, two sites were selected to conduct pile installation for the field test and the pile load test. For the pile load test, the static pile load test and the dynamic pile load test were carried out, and torque was measured during pile installation for the field test to compare and analyze expected bearing capacity and thus assess the feasibility of the method for estimating the bearing capacity. The field pile load test revealed the bearing capacity of the gravity grout pile was the same or greater than 600kN in the static pile load test in accordance with AC 358 Code. The non-grout pile showed the bearing capacity the same or smaller than 600kN, suggesting gravity grouting is required. Moreover, the field pile load test was used to establish the bearing capacity equation considering the torque in pile installation, and a small number of samples were used to establish the equation which can be used as a basic data.

Medical Device Design process carries a high responsibility when defining the characteristics of the object for its correct interaction with users. This study presents a proposal for the improvement of the medical device design processes, in order to increase user acceptance, considering two key factors: the hierarchy of users and the relationship with the patient's health status. The goal of the study seeks to address this research gap and raise design factors with practical suggestions for the design of new medical devices. The results obtained will help medical device designers in the development stage to make more informed decisions about the functions and features required in the final product; As well, in the design process didactics, demonstrating the importance of the correct execution of the process, and how the factors considered can generate an impact on the final product. An experiment was carried out with Forty design engineering students, who designed birthing beds, with two design processes, the traditional product design process, and the new design process based on hierarchies (proposed in this study). The results showed that there is a significant increase in user acceptance with the new birthing bed that was developed with the hierarchical based design process.

In this study, the field measurement-based validation of a novel sediment transport calculation method is presented. River sections with complex bed topography and inhomogeneous bed material composition highlight the need for an improved sediment transport calculation method. The complexity of the morphodynamic features can result in the simultaneous appearance of the gravel and finer sand dominated sediment transport (e.g. parallel bed armoring and siltation) at different regions within a shorter river reach. For the improvement purpose of sediment transport calculation in such complex river beds, a novel sediment transport method was elaborated. The base concept of it is the combined use of two already existing empirical sediment transport models. The method was already validated against laboratory measurements. The major goal of this study is the verification of the novel method with a real river case study. The combining of the two sediment transport models is based on the implementation of a recently presented classification method of the locally dominant sediment transport nature (gravel or sand transport dominates). The results are compared with measured bed change maps. The verification clearly refers to the meaningful improvement in the sediment transport calculation by the novel manner in case of spatially varying bed content.

Abstract: Safety issues related to the electrification of more electric aircraft (MEA) need to be addressed because of the increasing complexity of aircraft electrical power systems and the growing number of safety-critical sub-systems that need to be powered. Managing the energy storage systems and the flexibility in the load-side plays an important role in preserving the system’s safety when facing an energy shortage. This paper presents a system-level centralized operation management strategy based on model predictive control (MPC) for MEA to schedule battery systems and exploit flexibility in the demand-side while satisfying time-varying operational requirements. The proposed online control strategy aims to maintain energy storage (ES) and prolong the battery life cycle, while minimizing load shedding, with fewer switching activities to improve devices lifetime and to avoid unnecessary transients. Using a mixed-integer linear programming (MILP) formulation, different objective functions are proposed to realize the control targets, with soft constraints improving the robustness of the model. Besides, an evaluation framework is proposed to analyze the effects of various objective functions and the prediction horizon on system performance, which provides the designers and users of MEA and other complex systems with new insights into operation management problem formulation.

Surface finishing is challenging for additively manufactured components with complex geometries. Magnetic abrasive finishing (MAF) is a promising surface finishing technology that can refine the surface quality of components with complex shapes produced by additive manufacturing. However, there is insufficient study regarding the impact of MAF on microstructure-property relationships for additively manufactured builds, which is critical for evaluating the mechanical performance. Furthermore, although MAF is usually used as the final step of post-processing, it remains unclear whether adjusting the sequence between MAF and other processes, e.g., heat treatment, can potentially improve the mechanical performance. In this work, the effects of MAF on the microstructure and mechanical property evolution of Inconel 718 superalloys made by laser powder bed fusion (LPBF) were studied. The application of MAF was found to significantly reduce the surface roughness of alloys and refine the grain size of aged samples. Moreover, MAF is able to increase the elongation of materials, which can be further influenced by the sequence of MAF and different heat treatments. The highest elongation can be achieved when MAF is performed between homogenization and aging processes. This work demonstrated a promising solution to improving the performance of LPBF Inconel 718 by combining MAF and heat treatment, which provides new perspectives on the post-processing development of additively manufactured alloys for advanced mechanical properties.

This work aims to investigate the effect of catalyst content and reaction time by catalytic upgrading from pyrolysis vapors of residual fat at 450 °C and 1.0 atmosphere, on the yields of reaction products, physicochemical properties (density, kinematic viscosity, refractive index, and acid value) and chemical composition of organic liquid products (OLP), over a catalyst fixed bed reactor, in semi pilot scale. Pellets of Red Mud chemically activated with 1.0 M HCl were used as catalysts. The experiments were carried out at 450 °C and 1.0 atmosphere, using a process schema consisting of a thermal cracking reactor of 2.0 L coupled to a catalyst fixed bed reactor of 53 mL, without catalyst and using 5.0, 7.5, and 10.0% (wt.) Red Mud pellets activated with 1.0 M HCl, in batch mode. Samples of liquid phase products were withdrawn during the course of reaction at 40, 50, 60, 70 and 80 min in order to analyze the process kinetics. The physicochemical properties (density, kinematic viscosity, acid value, and refractive index) of OLP were determined by official methods. The chemical functions present in OLP determined by FT-IR and the chemical composition by GC-MS. The thermal catalytic cracking of residual fat show OLP yields from 54.4 to 84.88 (wt.%), aqueous phase yields between 2.21 and 2.80 (wt.%), solid phase yields (coke) between 1.30 and 8.60 (wt.%), and gas yields from 11.61 to 34.22 (wt.%). The yields of OLP increases with increasing catalyst content while those of aqueous, gaseous and solid phase decreases. For all the thermal and thermal catalytic cracking experiments, the density, kinematic viscosity, and acid value of OLP decreases with increasing reaction time. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, and aldehydes). For all the thermal and thermal catalytic cracking experiments, the hydrocarbon content within OLP increases with reaction time, while those of oxygenates decrease, reaching concentrations of hydrocarbons up to 95.35% (area.). The best results for the physicochemical properties (density, kinematic viscosity, and acid value) and the maximum hydrocarbon content of OLP were obtained at 450 °C and 1.0 atmosphere, using a catalyst fixed bed reactor, with 5.0% (wt.) Red Mud pellets activated with 1.0 M HCl as catalyst.

The power system vulnerability leads to faults and the severity of the fault may lead to prolonged load-shedding. The power system needs to be configured in extreme failure scenarios for protecting the network from further contingencies and prolonged load-shedding. Distributed generation resources (DGs) can be useful to form intentional islands after faults to maintain the continuity of power supply to loads based on their weightage during faulty periods and to reduce overall load shedding duration. Power system is bound to collapses and secondary collapse in the formed island is possible. This research represents a novel method of impedance based path finding for intentional islanding, which adapts itself with the changes in the demands, DGs outputs or further severities during restoration period. In this adaptive islanding approach, network adjusts itself with the changes in either the load demands or renewable DGs outputs and rearranges the restoration plan by curtailing or adding some of the loads through controllable switches. Further a secondary collapse in the existing island is studied by injecting multiple faults at various positions of the network to validate the system resilience to cope with severities. A short-term load forecasting approach is used to predict changes in load demands and variations in DG outputs during the islanding scheme. During the restoration period, these variations are tracked and the islands are modified accordingly. In order to minimize the overall generation cost by using less fuel, an economical approach is used in the selection of controllable DGs. The proposed approach is formulated as a multi-objective, that incorporates several operational constraints and simulation is carried out using the modified IEEE 69-bus distribution system to assess the efficacy of the proposed model.

Metal powder bed fusion (PBF) additive manufacturing (AM) builds metal parts layer by layer upon a substrate material. The strength of this interface between substrate and printed material is important to characterize, especially in applications where the substrate is retained and included in the finished part. This paper studied the tensile and torsional strengths of wrought and additively manufactured (through PBF) SS316L and compared them to specimens composed of half wrought material and half PBF material. The PBF specimens consistently exhibited higher strength and lower ductility than the wrought specimens. The hybrid PBF/wrought specimens performed similarly to the wrought material. In no specimens did any failure appear to occur at or near the interface between wrought substrate and PBF material. In addition, most of the deformation in the PBF/wrought specimens appeared to be limited to the wrought portion of the specimens. These results are consistent with microscopy showing smaller grain size in the PBF material, which often leads to increased strength in SS316L due to the Hall-Petch relationship.

Open-cell metallic foams used as catalyst supports exhibit excellent transport properties. In this work, a unique application of metallic foam, as pelletized catalyst in a packed bed reactor, is examined. By using a wall-segment Computational Fluid Dynamics (CFD) setup, parametric analyses are carried out to investigate the influence of foam morphologies (cell size ϕ=0.45-3 mm and porosity ε=0.55-0.95) and intrinsic conductivity on flow and heat transport characteristics in a slender packed bed (N=Ddp=6.78) made of cylindrical metallic foam pellets. The transport processes have been modeled using an extended version of conventional particle-resolved CFD, i.e., flow and energy in inter-particle spaces are fully resolved, whereas porous-media model is used for the effective transport processes inside highly-porous foam pellets. Simulation inputs include the processing parameters relevant to Steam Methane Reforming (SMR), analyzed for low (Rep~100) and high (Rep~5000) flow regimes. The effect of foam morphologies on packed beds has shown that the desired requirements contradict each other, i.e., increase in cell size and porosity favor the reduction in pressure drop, however lowering the heat transfer efficiency. A design study is also conducted to find the optimum foam morphology of a cylindrical foam pellet at higher Rep~5000, which yields ϕ = 0.45, ε = 0.8. Suitable correlations to predict the friction factor and the overall heat transfer coefficient in a foam packed bed have been presented, which considers the effect of different foam morphologies over a range of particle Reynolds number, 100≤Rep≤5000.

The main aim of this study is to investigate the optimization of the technological process for selective laser melting (SLM) additive manufacturing. The group of process parameters considered was selected from the first-stage parameters identified in preliminary research. Samples manufactured using three different sets of parameter values were subjected to static tensile and compression tests. The samples were also subjected to dynamic Split–Hopkinson tests. To verify the microstructural changes after the dynamic tests, microstructural analyses were conducted. Additionally, the element deformation during the tensile tests was analyzed using digital image correlation (DIC). To analyze the influence of the selected parameters and verify the layered structure of the manufactured elements, sclerometer scratch hardness tests were carried out on each sample. Basing on the research results it was possible to observe the porosity growth mechanism and its influence on the material strength (including static and dynamic tests). Parameters modifications that caused 20% lower energy density, elongation of the elements during tensile testing decreased twice, which was strictly connected with porosity growth. An increase of energy density by almost three times caused a significant reduction of force fluctuations differences between both tested surfaces (parallel and perpendicular to the building platform) during sclerometer hardness testing. That kind of phenomenon had been taken into account in the microstructure investigations before and after dynamic testing where it had been spotted a positive impact on material deformations based on fused material grains formation after SLM processing.

Tanning beds have been classified as carcinogenic to humans. As a result, many countries have enacted laws regulating the use of commercial tanning beds, including bans for minors. However, there is no international overview of the current legal status of access restrictions for minors that provides details on their specific design regarding age limits and possible exceptions to the statutory regulation. Therefore, we performed a comprehensive web search of current tanning bed legislation for minors on the three continents North America, Australia, and Europe. Our findings regarding existence and concrete design of access restrictions are presented graphically using maps. We found a wide variety of different legislations. In Australia, a total ban on tanning beds exists, while in New Zealand tanning bed use is banned for minors. In Europe about half of the countries have implemented a strict ban for minors. In North America we found differences in the age limit for access restrictions between the states, provinces and territories for those regions that implemented a ban for minors. In the United States, some states have rather ‘soft bans’ that allow use by minors with different types of parental consent. The patchwork in legislation calls for harmonization. Therefore, our comparison is an important starting point for institutions such as the World Health Organization or the European Commission to advance their goals towards a harmonization of tanning bed legislation in general and for minors in particular.

This work presents an alternative to harnessing wind energy with an Electromagnetic Frequency Regulator (EFR) coupled to a hydrostatic transmission and associated with a horizontal axis wind turbine, a bidirectional frequency inverter and a secondary energy source, in a hybridized system. The hydrostatic transmision is composed by a fixed displacement axial piston pump and a variable displacement, swash plate, axial piston motor. Feedback linearization was used as a technique to control the motor geometric displacement, and a prediction algorithm for the steady state rotations of the armature and the electromagnetic field has been developed. A 5\,kW project was simulated on a Scilab platform, with combinations of constant or variable load, and constant or variable wind speed. The results indicated that the system was able to supply the generator load, adapting to fluctuations in wind speed. The possibility of storing wind energy through the inverter has also been proven. The system can accumulate energy in batteries during the fastest wind regimes, to use it when the turbine power is lower than the load.

A theoretical nonlocal thermoelastic model for studying the effects of the thermal conductivity variability on a rotating nanobeam has been described in the present article. The theory of thermal stress is employed using the Euler–Bernoulli beam model and generalized heat conduction with phase lags. It is believed that the thermal conductivity of the current model varies linearly according to temperature. Due to variable harmonic heat, the considered nanobeam excited and was subjected to a time-varying exponential decay load. Using the Laplace transform process, the analytical solutions for displacement, deflection, thermodynamic temperature and bending moment of rotating nanobeams are provided in final forms and a numerical example has been taken to address the problem. A comparison of the stated results was displayed and additionally, the influences of non-local parameters and varying load were analyzed and examined. We also investigate how the linear changes in the temperature of physical properties can influence both the static and dynamic responses to the rotating nanobeam.

Abstract: A lower bed single row for pineapple cultivation could protect pineapple from soil erosion in rainy season and during drought, however, disease problem could arise due to water logging. Two experiments using a lower bed single row was done to understand the ability of gypsum providing soil calcium (Ca) available to pineapple plant, resistance to heart rot disease, and give better effect on crop growth and fruit quality of the pineapple in Ultisol soil. In the first trial, four level dosis of gypsum (0, 1.0, 1.5, 2.0 Mg ha-1) and dolomite 2 Mg ha-1 were applied by spreading and incorporated into the soil which have saturated with inoculums of Phytophthora nicotianae. In the second trial, gypsum treatments (0, 1.0, 1.5, 2.0, 2.5 Mg ha-1) were applied in the row between the single row beds as a basic fertilizer. The result showed that P. nicotianae attacked the pineapple plants in all treatments at 6 weeks after planting (WAP), and at 10 WAP, the mortality of dolomite treatment reached 63.8%, significantly different than that for gypsum treatments (3.3-14.3%). In the second experiment, gypsum increased plant weight significantly at 3 until 9 months after planting especially when it was applied 1.5-2.5 Mg ha-1. Fruit texture, total soluble solid (TSS), titratable acidity (TA) were not significant different among the treatment but all meet the standards for grades of canned pineapple. Result showed that soil applied gypsum before planting provides soil calcium and met the plant Ca requirement during a period of early and fast growth step and safe for heart rot disease.

A long-term forecast study on the electricity demand of Taoussa of Mali is conducted in this paper, with various scenarios of socioeconomic and technological conditions. The analysis tool, which is applied in scenarios simulation, is the Model for Analysis of Energy Demand from the International Atomic Energy Agency. The analysis results are annual electricity demand and peak load forecast for the electrification from the period 2020 to 2035. During the planning period, the analysis results show that the electricity demand will increase to 49.40 MW (332.57 GWh) for the low scenario (LS), 66.46 MW (472.61 GWh) for the reference scenario (RS), and 89.47 MW (635 GWh) for the high scenario (HS). In addition, the total electricity demand increased at an average rate of 8.13% in the LS, 10.31% in the RS and 12.56% in the HS in all sectors. The electricity peak demand is expected to grow at 7.92%, 10.53% and 12.91% corresponding to the three scenarios; in this case, the system peak demand in 2035 will increase to 64.88 MW for the LS, 92.2 MW for the RS and 126.22 MW, the days of peak load are between 17th -23rd in May. The Industry sector will be the biggest electricity consumer of Taoussa area.

Load Frequency Control (LFC) is essential to ensure the stability and performance of power systems. In this study, a novel optimization algorithm, the Sea Horse Optimizer (SHO) algorithm, was proposed for optimizing controller parameters in LFC problems of power system. The proposed SHO algorithm was tested on a two-area power system with photovoltaic system and reheat thermal units, under three different scenarios: a 10% load change in both area, large load disturbances, and varying solar radiation. The proposed algorithm optimizes the gain parameters of PI/PID controllers using performance metrics such as Integral of Absolute value of the Error (IAE), Integral of Square Error (ISE), Integral of Time multiplied by Square Error (ITSE), and Integral of Time multiplied by Absolute Error (ITAE). The study compared the performance of the SHO-optimized controller with other reported optimization algorithms such as Genetic Algorithm (GA), Firefly Algorithm (FA), Whale Optimization Algorithm (WOA), and Modified Whale Optimization Algorithm (MWOA). The study also evaluated the accuracy and effectiveness of the controllers using performance metrics such as Settling Time, Overshoot (M+), and Undershoot (M-). The results show that the SHO-tuned controller significantly reduces overshoot, undershoot, and settling time of the system oscillations compared to other algorithms. The study provides valuable insights into the optimization of LFC controllers and presents a significant contribution to the literature with its novel algorithm. The proposed SHO algorithm can be considered an effective alternative solution method for LFC in power systems.

The accurate prediction of heat load profiles with a daily resolution is required for a broad range of applications such as potential studies, design, or predictive operation of heating systems. If the heat demand of a consumer is mainly caused by (production) processes independent of the ambient temperature, existing load profile prediction methods fail. To close this gap, this study develops two ex post machine learning models for the prediction of the heat demand with a daily resolution. The selected input features are commonly available to each consumer connected to public natural gas and electricity grids or operating an energy monitoring system: Ambient temperature, weekday, electricity consumption, and heat consumption of the last seven days directly before the predicted day. The study’s database covers electricity and natural gas consumption load profiles from 82 German consumers over a period of two years. Electricity and heat consumption correlate strongly with individual patterns for many consumers. Both, shallow and deep learning algorithms are evaluated. The highest accuracy is achieved by a Long Short Term Memory (LSTM) model with a median of R² of 0.94. The ex post model architecture makes the model suitable for automated anomaly detection in energy monitoring systems.

In this work, we have developed a non-ordinary state-based peridynamic model for multiple crack initiation and propagation due to compression-compression fatigue load. In each loading cycle, the fatigue loading is redistributed among the peridynamic solid body, leading to the progressive fatigue damage initiation and propagation in an autonomous fashion. The proposed fatigue model parameters are firstly validated by 3D numerical benchmark tests, and then it is applied to simulate widespread fatigue damage evolution of the aircraft wing corner box. The modified constitutive damage model has been implemented into the peridynamics framework at finite strain. Furthermore, the criterion algorithm from multiple initiation to propagation is discussed. It is shown that the numerical results obtained from peridynamics simulations are in general agreement with those from the experiment data. The comparison of experimental and numerical results indicates that the proposed non-ordinary state-based peridynamics fatigue model has the ability to capture the multiple crack initiation and propagation and other features of the aluminium alloy material.

The load of power system changes with the development of economy, short-term load forecasting play a very important role in dispatching and management of power system. In this paper, the Ant Lion Optimizer (ALO) is introduced to improve the input weights and hidden-layer Matrix of extreme learning machine (ELM), after the parameters of ELM are optimized by ALO, then input nodes, hidden layer nodes and output nodes are determined, so a load forecasting model based on ALO-ELM combined algorithm is established. The proposed method is illustrated based on the historical load data of a city in China. The results show that the average absolute error of short-term load demand predicted by ALO-ELM model is 1.41, while that predicted by ELM is 4.34, the proposed ALO-ELM algorithm is superior to the ELM and meet the requirements of engineering accuracy, which proves the effectiveness of proposed method.

The use of commodity polymers such as polypropylene (PP) is key to open new market segments and applications for the additive manufacturing industry. Technologies such as powder-bed fusion (PBF) can process PP powder; however, much is still to learn concerning process parameters for reliable manufacturing. This study focusses in the process-property relationships of PP using laser-based PBF. The research presents an overview of the intrinsic and the extrinsic characteristic of a commercial PP powder as well as fabrication of tensile specimens with varying process parameters to characterize tensile, elongation at break, and porosity properties. The impact of key process parameters, such as power and scanning speed are systematically modified in a controlled design of experiment. The results were compared to the existing body of knowledge; the outcome is to present a process window and optimal process parameters for industrial use of PP. The computer tomography data revealed a highly porous structure inside specimens ranging between 8.46% and 10.08%, with porosity concentrated in the interlayer planes in the build direction. The results of the design of experiment for this commercial material show a narrow window of 0.122 ≥ Ev ≥ 0.138 J/mm³ led to increased mechanical properties while maintaining geometrical stability.

The chicken poultry business is becoming a crucial sector for our nation's sustainable food supply. To increase the health of chickens in coops and maybe increase the output of chicken meat and eggs, several innovations and inventions have been developed. Therefore, the creation of an automated chicken feeding device might be highly beneficial for the expansion of the poultry sector. This equipment may take the role of a worker in the chicken feeding process, solving the industry's labor shortage and introducing a semi-automatic procedure. The main processor of the automated chicken feeding system is a Raspberry Pi 3 Model B+. The machine consists of five main components: a Raspberry Pi with an amplifier that makes noise to draw the attention of free-range chickens, a Raspberry Pi with a pi camera that counts and detects the chickens, a Raspberry Pi with a servomotor that moves the food from storage to a container, a Raspberry Pi with a load cell that controls the number of feeds to avoid waste on foods, and a Raspberry Pi with a temperature sensor that monitors the food's freshness. This enhances the coop's atmosphere while lowering labor costs, conserving food, and ensuring that the chickens are fed on time. It also regulates the temperature sensor to ensure that the chicken food is fresh and prevents food from becoming polluted by insects and chicken excrement.

An adaptive control technique has been implemented for DSTATCOM for power quality enhancement in three phase four wires(3P4W) distribution system. The reference source currents are extracted from active components of load current for each phase by using this technique. It has also been used for load balancing, harmonic suppression, power factor improvement and reactive power compensation in distribution system. The adaptive control technique has been tested at varying load in steady state and dynamic conditions. This technique is developed using MATLAB/Simulink and source side harmonics are mitigated under different load conditions which are acceptable in accordance with IEEE standard.

Cumulative effects of landscape disturbance in forested source water regions can alter the storage of fine sediment and associated phosphorus in riverbeds, shift nutrient dynamics and degrade water quality. Here, we examine longitudinal changes in major element chemistry and particulate phosphorus (PP) fractions of river-bed sediment in an oligotrophic river during environmentally sensitive low flow conditions. Study sites along 50 km of the Crowsnest River were located below tributary inflows from sub-watersheds and represent a gradient of increasing cumulative sedi-ment pressures across a range of land disturbance types (harvesting, wildfire, and municipal wastewater discharges). Major elements (Si2O, Al2O3, Fe2O3, MnO, CaO, MgO, Na2O, K2O, Ti2O, V2O5, P2O5), loss on ignition (LOI), PP fractions (NH4CI-RP, BD-RP, NaOH-RP, HCI-RP and NaOH(85)-RP) and absolute particle size were evaluated for sediments collected in 2016 and 2017. While total PP concentrations were similar across all sites, bioavailable PP fractions (BD-RP, NaOH-RP) increased downstream with increased concentrations of Al2O3 and MnO and levels of landscape disturbance. This study highlights the longitudinal water quality impacts of increasing landscape disturbance on bioavailable PP in fine riverbed sediments and shows how the convergence of climate (wildfire) and anthropogenic (sewage effluent, harvesting, agriculture) drivers can produce legacy effects on nutrients.

Contact-based co-culture of fibroblasts and keratinocytes is important to study the structure and functions of the wound bed. Co-culture of these two cell types in direct contact with each other has been challenging, requiring high serum concentrations (up to 10%), feeder systems and a range of supplemental factors. These approaches are not only technically demanding, but also present scientific, cost and ethical limitations associated with high-serum concentrations. We have developed two reduced-serum approaches (1-2%) to support contact-based co-culture of human dermal fibroblasts (HDFa) and human epidermal keratinocytes (HaCaT). The two approaches include (1) Specialized cell culture media for each cell type mixed in a 1:1 ratio (KGM+FGM), and (2) Minimal media supplemented with cell-specific growth factors (MEM+GF). Co-culture could be successfully achieved by co-seeding (two cell types were introduced simultaneously), or in a layered fashion (keratinocytes seeded on top of confluent fibroblasts). With wound scratch assays, the co-cultured platforms could demonstrate cell proliferation, migration and wound closure. The reduced-serum conditions developed are simple, easy to formulate and adopt, and based on commonly-available media components. These contact-based co-culture approaches can be leveraged for wound and skin studies, and tissue bioengineering applications, potentially reducing concerns with high-serum formulations.

The diagnosis of a rolling bearing for monitoring its status is critical for maintaining industrial equipment using rolling bearings. The traditional method of diagnosing faults of the rolling bearing has low identification accuracy, which needs artificial feature extraction to enhance the accuracy. 1D-CNN method not only can diagnose bearing faults accurately but also overcome shortcomings of the traditional methods. Different from machine learning and other deep learning models, the 1D-CNN method does not need pre-processing one-dimensional data of rolling bearing’s vibration. Thus, it enhances the processing speed and improves the network structure to have a reasonable design for small sample data sets. This study proposes and tests a 1D-CNN method for diagnosing rolling bearings. By introducing the dropout operation, the method obtains high accuracy and improves the generalizing ability. The experimental results show 99.52% of the average accuracy under a single load and 98.26% under different loads.

In humans, age-associated degrading changes are observed in molecular and cellular processes underly the time-dependent decline in spatial navigation, time perception, cognitive and psy-chological abilities, and memory. Cross talk of biological, cognitive, and psychological clocks provides an integrative contribution to healthy and advanced aging. At the molecular level, ge-nome, proteome, and lipidome instability are widely recognized as the primary causal factors in aging. We narrow attention to the roles of protein aging linked to prevalent amino acids chirali-ty, enzymatic and spontaneous (non-enzymatic) post-translational modifications (PTMs SP), and non-equilibrium phase transitions. The homochirality of protein synthesis, resulting in the steady-state non-equilibrium condition of protein structure, makes them prone to multiple types of enzymatic and spontaneous PTMs, including racemization and isomerization. Spontaneous racemization leads to the loss of the balanced prevalent chirality. Advanced biological aging re-lated to irreversible PTMs SP has been associated with the nontrivial interplay between poor so-matic and mental health conditions. Through stress response systems (SRS), the environmental and psychological stressors contribute to the age-associated “collapse” of protein homochirality. The role of prevalent protein chirality and entropy of protein folding in biological aging is mainly overlooked. In a more generalized context, the time-dependent shift from enzymatic to the non-enzymatic transformation of biochirality might represent an important and yet un-der-appreciated hallmark of aging.

Considering the fault "N-1" checksum and the power flow, the single-phase power flow model is further transformed into a three-phase power flow model, and the asymmetry of the three-phase power flow is measured by the three-phase unbalance factor. The calculation model is linearized by the second-order cone relaxation and the Big-M method. At the same time, the load response and distribution network reconstruction are used to improve the reliability of the power supply network to cope with the power failure. The relationship between power supply capability and power flow constraints, main transformer capacity and distributed power parameters is analyzed by IEEE 33-node three-phase power distribution system. The feasibility of the proposed model and the accuracy of the second-order cone relaxation are verified by numerical examples, which provides a technical reference for distribution network planning.

In this paper, initially a mathematical model is formulated for transient frequency of power system considering time delays which occur while transmitting the control signals in open communication infrastructure. Time delay negligence in a power system leads to improper measurement of frequency variation in power system. The study of impact of time delays on the stability of power system is performed by estimating the decay rate of frequency wave form using Kalman Filter (KF). In power system, there is a possibility of multiple time delays. This paper also focusses on developing Interacting Multiple Model (IMM) Algorithm with multiple model space using Kalman Filter (KF) as state estimator tool. The multiple time delays in power system is considered as multiple model space. The result shows that KF provides better estimate of correct model for a particular input-set. The qualitative properties of Riccati difference equation (RDE) in terms of state error covariance of IMMKF are also analyzed and presented.

Sudden variation of aerodynamic loads is the potential source of safety accidents of high-speed train (HST). As a follow-up investigation on the aerodynamic response of a HST that enters a tunnel under crosswind environment, this paper focuses on the transient response of a HST’s safety indices based on the train–track coupling interaction model. Firstly, a wind–train–track coupling dynamic model is proposed by introducing transient aerodynamic loads into the vehicle–track system. Secondly, the temporal evolution of safety coefficients indicates that the train’s safety risk increases during tunnel entry with crosswind. Results show that the derailment coefficients and wheel load reduction rate during tunnel entry are not only larger than those in open air but also those inside the tunnel due to the sudden disappearance of wind excitation at the tunnel entrance. In addition, the characteristic wind curve, which is the wind velocity against the train speed, is presented for application based on the current specification of the safety criteria threshold. The investigation will be useful in assessing the safety risk of a running train subjected to other aerodynamic attacks, such as the coupling effect of infrastructure scenario and crosswind in windy area.

In the last years, the Distribution Grid Operators (DGOs) assumed transition strategies of the distribution grids towards an active area associated with the "Smart Grids" concept. They are considering the use of Artificial Intelligence techniques, combined with advanced technologies and real-time remote communication solutions of the enormous data amounts, to develop smart solutions into the small size distribution grids, also called microgrids (μGs). These solutions will provide support for the DGOs to ensure an optimal operation of the technical infrastructure of the μGs. In this context, a bi-level methodology for solving the phase load balancing problem in the μGs with complex topologies and a high number of single-phase consumers, considering a clustering-based selection criterion of the consumers for placement of the switching devices, was proposed in the paper. A real μG from a rural area, with 114 consumers integrated into the Smart Metering System (SMS), belonging to the DGO from Romania, was considered in testing the proposed methodology. An implementation degree of 17.5%, corresponding to the phase load balancing equipment installed to only 20 consumers from the μG, led to a faster computational time with 43% and reducing the number of switching operations by 92% than in the case of a full implementation degree (100%). The performance indicators related to the unbalance factor and energy-saving used in the evaluation of the technical benefits highlighted the efficiency of the proposed methodology.

Bedbug (Cimex spp.) are a nuisance public-health pest that is on the rise globally, particularly in crowded cities such as Hong Kong. To investigate the health impacts of bedbug infestations among bedbug victims, online surveys were distributed in Hong Kong between June 2019 to July 2020. Data on sociodemographics, self-rated health, average hours of sleep per day, and details of bedbug infestation were collected. Bivariate and multivariable analysis were performed using logistic regression. The survey identified 422 bedbug victims; among them, 223 (52.9%) experienced ≥5 bites in the past month, most bites occurred on the arms (n=202, 47.8%) and legs (n=215, 51%), and the most common reaction to bites were itchiness (n=322, 76.3%), redness, and swelling of the skin (n=246, 58.1%), and difficulties sleeping or restlessness (n=125, 29.6%). Bites usually occurred during sleep (n=230, 54.5%). For impact on daily life in the past month, most bedbug victims reported moderate to severe impact on mental and emotional health (n=223, 52.8%) and sleeping quality (n=239, 56.6%). Lower self-rated health (aOR&lt;1) was independently associated with impact to physical appearance (p=0.008), spending money on medication or doctor consultation (p=0.04), number of bites in the past month (p=0.023), and irregular time of bites (p=0.003). Lower average hours of sleep per day (aOR&lt;1) was independently associated with impact on mental and emotional health (p=0.016). This study brings attention to the neglected issue of bedbug infestation by considering bedbugs as an infectious agent instead of a vector and providing empirical evidence describing its health impacts.

Cerebrospinal fluid (CSF) viral escape has been poorly described among people with HIV-associated cryptococcal meningitis. We determined the prevalence of CSF viral escape and HIV-1 viral load (VL) trajectories in individuals treated for HIV-associated cryptococcal meningitis. A retrospective longitudinal study was performed using paired CSF and plasma collected prior to and during the antifungal treatment of 83 participants recruited at the Botswana site of the phase-3 AMBITION-cm trial (2018-2021). HIV-1 RNA levels were quantified then CSF viral escape (CSF HIV-1 RNA ≥ 0.5 log10 higher than plasma) and HIV-1 VL trajectories were assessed. CSF viral escape occurred in 20/62 (32.3%; 95% confidence interval [CI]: 21.9%-44.6%), 13/52 (25.0%; 95% CI: 15.2%-38.2%) and 1/33 (3.0%; 95% CI: 0.16%-15.3%) participants at days 1, 7 and 14 respectively. CSF viral escape was significantly lower on day 14 compared to days 1 and 7, p=0.003 and p=0.02, respectively. HIV-1 VL de-creased significantly from day 1 to day 14 post antifungal therapy in the CSF but not in the plasma (OR, 0.56; 95% CI: 0.41-0.77; p<0.001). CSF viral escape is high among individuals presenting with HIV-associated cryptococcal meningitis; however, antifungal therapy may reverse this, highlighting the importance of rapid initiation of antifungal therapy in these patients.

In this paper, an offshore airborne wind energy (AWE) farm consisting of three non-reversing pumping mode AWE systems is modelled and simulated. The AWE systems employ permanent magnet synchronous generators (PMSG). A direct interconnection technique is developed and implemented for AWE systems. This method is a new approach invented for interconnecting offshore wind turbines with the least number of required offshore-based power electronic converters. The direct interconnection technique can be beneficial in improving the economy and reliability of marine airborne wind energy systems. The performance and interactions of the directly interconnected generators inside the energy farm internal power grid are investigated. The results of the study conducted in this paper, show the directly interconnected AWE systems can exhibit a poor load balance and significant reactive power exchange which must be addressed. Power control strategies for controlling the active and reactive power of the AWE farm are designed, implemented, and promising results are discussed in this paper.

A novel effective vibrational mode was discovered in the conventional transducer with an array of orthogonal (square) regular piezoelectric rods in 1-3 piezocomposite, containing the damping backing and front matching layers. The operational resonance in the structure was determined as the Surface Acoustic Wave (SAW) on the backing boundary excited by the adjacent piezo-rods, with its frequency typically near 3 times lower the fundamental half-lambda conventional piezocomposite resonance. Pulse-echo sensitivity and transmitting sound-pressure-level (SPL) in air showed that the signal strength is roughly comparable to the industrial similar air transducers at the frequency range 100…700 kHz, where at these frequencies the lateral and longitudinal piezoelement dimensions in the conventional transducer design are typically close to each other causing interference with unwanted coupling modes. As was determined theoretically and proved in experiments, the backing SAW resonance effect in the transducer performance is inherent just to the regular periodic 1-3 piezocomposite structure, and does occur neither with randomly located/oriented piezo-rods, nor in the homogeneous piezo-plate at least with the same lateral cross-section as the connected to it backing. The purpose of the article is to investigate a newly discovered operational vibrational mode of a SAW type in 1-3 regular piezocomposite, other than piezoelectric resonance. The investigated phenomena can improve the transceiver sensitivity, bandwidth, providing lower drive voltage, and smaller and lighter weight ultrasonic transducers. Based on the piezocomposites with thickness’ 1…1.5 mm (rod resonance near 2…3 MHz), pillar width 0.2…0.8 mm, kerf width 0.1…0.4 mm, the transceivers with an operating frequency from 140 kHz to 650 kHz were designed and fabricated with a conventional backing of a mixture of high-density tungsten powder and epoxy, and a matching layer of a mixture of low-density glass bubbles and epoxy. Experimental evaluation of their acoustical performance showed expected characteristics suitable for practical applications.

Load forecasting is an important component of power system and resource planning for electrical grids. The adoption of electric vehicles (EVs), behind-the-meter (BTM) solar, and heat pumps will significant change the amount and variability of loads. Electrification adoption and load forecasting in arctic regions and Alaska is limited. This paper provides the first load and electrification adoption forecast for the Alaska Railbelt transmission system, including yearly adoption rates of EVs, BTM solar, and heat pumps and hourly load data. Adoption rates are based on available historical data and compared to other regional and national trends. Two forecasts are created: 1) a moderate adoption forecast based on projections from current adoption rates and comparisons to other projections, and 2) an aggressive forecast, which provides a bookend comparison at the high adoption rate of 90% for all technologies. The results of these forecasts demonstrate a significant increase in both energy, 80% and 116% for moderate and aggressive, respectively and peak load demand, 113% and 219% for moderate and aggressive, respectively. Additionally, the results indicate a maximum hourly load change of 260% and 381% for the moderate and aggressive forecasts, respectively. These findings highlight a need for resource planning, which accounts for increases in demand and suggests that significant demand management is needed to smooth and control the load fluctuations as a result of the adoption of EVs, BTM solar, and heat pumps.

Overcrowding in the emergency department is a problem that generates several implications for bed management, which is deemed one of a hospital's most critical processes. Effective management of hospital production capacity includes bed management processes, which can be improved in order to leverage hospital performance. Thus, this study sought to understand how bed management works and identify the main factors that influence its management. The study was performed through a case study, with data collected from semi-structured interviews and bibliographic research, which were triangulated. Thematic content analysis of the interviews and cross-analysis were performed. As a result, the main factors that influence hospital Bed management were identified: communication between teams and units; definition of performance goals; decisions shared between units; occupation and discharge planning by the teams; length of stay; the role of the nurses; and COVID-19. The greatest difficulties in the management process are related to these factors. Additionally, suggestions are provided to mitigate such reported difficulties.

The work presents an approach to instrument the load sensing bearings for automotive applications for estimation of the loads acting on the wheels. The system comprises fiber-optic sensors based on addressed fiber Bragg structures (AFBS) with two symmetrical phase shifts. A mathematical model for load-deformation relation is presented, and the AFBS interrogation principle is described. The simulation includes (i) modeling of vehicle dynamics in a split-mu braking test, during which the longitudinal wheel loads are obtained, (ii) the subsequent estimation of bearing outer ring deformation using a beam model with simply supported boundary conditions, (iii) the conversion of strain into central wavelength shift of AFBS, and (iv) modeling of the beating signal at the photodetector. The simulation results show that the estimation error of the longitudinal wheel force from the strain data acquired from a single measurement point was 5.44% with root-mean-square error of 113.64 N. A prototype load sensing bearing was instrumented with a single AFBS sensor and mounted in a front right wheel hub of an experimental vehicle. The experimental setup demonstrated comparable results with the simulation during the braking test. The proposed system with load-sensing bearings is aimed at estimation of the loads acting on the wheels, which serve as input parameters for active safety systems, such as automatic braking, adaptive cruise control, or fully automated driving, in order to enhance their effectiveness and safety of the vehicle.

Silty clay modified by fly ash and crumb rubber is a kind of sustainable subgrade filler which has good anti-freeze-thaw resistance stability but wake vibration isolation performance. The objective of this study was to improve the vibration isolation of the modified soil and investigate the vibration isolation effect of the composite subgrade structure of XPS plates and the modified soil by indoor impact test. First, the vibration isolation performance of silty clay, modified soil and composite subgrade structure was respectively evaluated. Second, the effect of XPS plate’s thickness and vibration intensity on the vibration performance of the composite subgrade structure were evaluated. Third, the vibration isolation performance of the test groups under the condition of freeze-thaw cycles was assessed. The results show that the vibration isolation performance of subgrade can be effectively improved by setting XPS plates. The composite subgrade structure has certain vibration isolation effect, especially in vertical direction. Considering vibration isolation performance and costs, 5cm is the optimum XPS plates thickness. The composite subgrade structure has great vibration isolation performance under the condition of freeze-thaw cycles, so it is suitable to be applied in road subgrade in seasonal frozen regions.

The work is devoted to the study of the mechanisms of damage accumulation in a polymer composite material (PCM) during fatigue loading. Mechanical testing of a fiberglass sample was carried out by cyclic tension accompanied by registration of acoustic emission (AE). For the recorded AE signals, the Fourier spectra were calculated and used for clustering with Kohonen self-organizing map. Relations between clusters and types of damage in the PCM structure were established. The analysis of the peak frequencies of the Daubechies D14-wavelet components of AE signals was carried out. Obtained results has allows one to describe the processes of destruction in the PCM sample. It has been established that, on the base of local formation of microdamages in the matrix and the fracture of the fibers detected during recording of the AE data, it is possible to predict the destruction of the polymer composite material, while the beginning of a material destruction can be registered if the damage identified as an adhesion failure is observed. Perspectives of application of adaptive fiber-optic AE sensors for structural monitoring of PCMs on the base of preliminary experimental results are considered and discussed.

Introduction- The dynamics of SARS-CoV-2 shedding and replication in humans remain incompletely understood. Methods- We analyzed SARS-CoV-2 shedding from multiple sites in individuals with an acute COVID-19 infection by weekly sampling for five weeks in 98 immunocompetent and 25 immunosuppressed individuals. Samples and culture supernatants were tested by RT-PCR for SARS-CoV-2 to determine viral clearance rates and in vitro replication. Results- A total of 2447 clinical specimens were evaluated, including 557 nasopharyngeal swabs, 527 saliva samples, 464 urine specimens, 437 anal swabs and 462 blood samples. The SARS-CoV-2 genome sequences at each site were classified as belonging to the B.1.128 (ancestral strain) or Gamma lineage. SARS CoV-2 detection was highest in nasopharyngeal swabs regardless of the virus strain involved or the immune status of infected individuals. The duration of viral shedding varied between clinical specimens and individual patients. Prolonged shedding of potentially infectious virus varied from 10 days up to 191 days, and primarily occurred in immunosuppressed individuals. Virus was isolated in culture from 18 nasal swab or saliva samples collected 10 or more days after onset of disease. Conclusions-Our findings indicate that persistent SARS-CoV-2 shedding may occur in both competent or immunosuppressed individuals, at multiple clinical sites and in a minority of subjects is capable of in vitro replication.

Joints between walls are very important for structural analysis of each masonry building at the global and local level. This issue was often neglected in case of traditional joints and relatively squat walls. Nowadays the issue of wall joints is becoming particularly important due to the continuous strive for simplifying structures, introducing new technologies and materials. Eurocode 6 and other standards (USA, Canadian, Chinese, and Japanese) recommend inspecting joints between walls, but no detail procedures have been specified. This paper presents our own tests on joints between walls made of autoclaved aerated concrete (AAC) masonry units. Tests included reference models composed of two wall panels joined perpendicularly with a masonry bond (6 models), traditional steel and modified connectors (12 models). A shape and size of test models and structure of a test stand were determined on the basis of the analysis of the current knowledge, pilot studies and numerical analyses of FEM. The analysis referred to the morphology and failure mechanism of models. Load-displacement relationships for different types of joints were compared and obtained results were referred to results for reference models. A mechanism of cracking and failure was found to vary, and clear differences in behaviour and load capacity of each type of joints were observed. Individual working phases of joints were determined and defined, and the empirical approach was suggested to determine forces and displacement of wall joints.

Understanding how the deformed bed topography induced by near-bank vegetation impacts the hydrodynamics is significant for understanding the maintenance condition of bed morphology and further fluvial evolution. This issue has rarely been addressed by current studies. This study with a 2D hydro-morphological model investigates the hydrodynamics over flat and deformed beds with a near-bank vegetation patch. By varying the patch density, the generalized results show that the hydrodynamics for the deformed bed differs a lot from those for the flat bed. It is found that deformed bed topography leads to an apparent decrease in longitudinal velocity and bed shear stress in the open region and longitudinal surface gradient for the entire vegetated reach. However, the transverse flow motion and transverse surface gradient in the region of the leading edge and trailing edge is enhanced or maintained, suggesting the strengthening of secondary flows. Interestingly, the deformed bed topography tends to alleviate the turbulent effect caused by the junction-interface horizontal coherent vortices, indicating that the turbulence-induced flow mixing is highly inhibited by the deformed bed. Alternatively, the enhanced secondary flows might provide compensation for the flow mixing for the deformed bed, confirmed by a faster recovery of the redistributed water discharge for the vegetated and open regions to the normal value (50%). The interior flow adjustment through the patch for the deformed bed requires a shorter distance, which links the vegetative drag length with a logarithmic relation. The tilting bed topographic effect in the open region to accelerate the flow may account for the faster flow adjustment.

This work presents the results of three connection types in double-shear with dowel fasteners, using the simplified equations from the Eurocode 5. All design parameters were established and compared using three different wood strength and density properties, which constitute the members connections. Eighty-one connections were obtained, allowing to conclude about the number of fasteners needed to the applied tensile load. An increase in the number of dowels was obtained with the increased applied tensile load, lower dowel diameter, lower wood density, and lower strength material in all connection types in the study. The design characteristic load-carrying capacity per shear plane and fastener also decrease with the previously considered parameters.

Demand-Side Management (DSM) is an essential tool to ensure power system reliability and stability. In future smart grids, certain portions of a customer’s load usage could be under the automatic control of a cyber-enabled DSM program, which selectively schedules loads as a function of electricity prices to improve power balance and grid stability. In this scenario, the security of DSM cyberinfrastructure will be critical as advanced metering infrastructure and communication systems are susceptible to cyber-attacks. Such attacks, in the form of false data injections, can manipulate customer load profiles and cause metering chaos and energy losses in the grid. The feedback mechanism between load management on the consumer side and dynamic price schemes employed by independent system operators can further exacerbate attacks. To study how this feedback mechanism may worsen attacks in future cyber-enabled DSM programs, we propose a novel mathematical framework for (i) modeling the nonlinear relationship between load management and real-time pricing, (ii) simulating residential load data and prices, (iii) creating cyber-attacks, and (iv) detecting said attacks. In this framework, we first develop time-series forecasts to model load demand and use them as inputs to an elasticity model for the price-demand relationship in the DSM loop. This work then investigates the behavior of such a feedback loop under intentional cyber-attacks. We simulate and examine load-price data under different DSM-participation levels with three types of random additive attacks: ramp, sudden, and point attacks. We conduct two investigations for the detection of DSM attacks. The first studies a supervised learning approach, with various classification models, and the second studies the performance of parametric and nonparametric change point detectors. Results conclude that higher amounts of DSM participation can exacerbate ramp and sudden attacks leading to better detection of such attacks, especially with supervised learning classifiers. We also find that nonparametric detection outperforms parametric for smaller user pools, and random point attacks are the hardest to detect with any method.

This paper, we examined the technology to maximize the use of renewable energy. The passive ventilation system is expected to reduce the energy consumption of the fan power and the maintenance burden. In addition, the wall-mounted solar air heater can supply thermal energy without using any energy at all. Therefore, we propose a "passive ventilation system with a solar air heater" that combines a passive ventilation system with solar air heater to preheat the air supply and reduce the ventilation load. To evaluate the solar air heater performance in a real environment, we developed a simulation for calculating the heat collection capacity of the solar air heater, and then implemented the system in a real building for verification. Based on the measurement results, the effects of heating load reduction and prediction methods are presented.

A thermal load dispatch problem minimizes the number of objectives viz operating cost and emission of gaseous pollutants together while allocating the power demand among the committed generating units subject to physical and technological system constraints. A stochastic thermal load dispatch problem is undertaken while taking into consideration, the uncertainties, errors in data measurements and nature of load demand which is random. Owing to uncertain load demand, variance due to mismatch of power demand termed as risk, is considered as another conflicting objective to be minimized. Generally multiobjective problems generate a set of non-inferior solutions are generated and supplied to a decision maker to select the best solution from the set of non-inferior solutions. This paper proposes opposition-based greedy heuristic search (OGHS) method to generate a set of non-inferior solutions. Opposition-based learning is applied to generate initial population to select good candidates. Migration to maintain diversity in the set of feasible solutions is also based on opposition-based learning. Mutation strategy is implemented by perturbing the genes heuristically in parallel and better one solution is sought for each member. Feasible solutions are achieved heuristically by modifying the generation-schedules in such a manner that violation of operating generation limits are avoided. The OGHS method is simple to implement and provides global solutions derived from the randomness of the population generated without tuning of parameters. Decision maker exploits fuzzy membership functions to decide the final decision. Validity of the method has been demonstrated by analysing systems in different scenarios consisting of six generators and forty generators.

White Spot Syndrome Virus (WSSV) has emerged as one of the most prevalent and lethal viruses globally, and infects both shrimps and crabs in the aquatic environment. This study aimed to investigate the occurrence of WSSV in different ghers of Bangladesh and the virulence of the circulating phylotypes. We collected 360 shrimp (Penaeus monodon) and 120 crab (Scylla sp.) samples from the South-East (Cox’s Bazar) and South-West (Satkhira) coastal regions of Bangladesh. The VP28 gene-specific PCR assays and sequencing revealed statistically significant (p < 0.05, Kruskal Wallis test) differences in the prevalence of WSSV in shrimps and crabs between the study areas (Cox’s Bazar and Satkhira), and over the study periods (2017-2019). The mean Log load of WSSV varied from 8.40 (Cox’s Bazar) to 10.48 (Satkhira) per gram of tissue. The mean values for salinity, dissolved oxygen, temperature and pH were 14.71±0.76 ppt, 3.7±0.1 ppm, 34.11±0.38˚C and 8.23±0.38, respectively in the WSSV-positive ghers. The VP28 gene-based phylogenetic analysis showed an amino-acid substitution (E→G) at 167th position in the isolates from Cox’s Bazar (referred to as phylotype BD2) compared to the globally circulating one (BD1). Shrimp PL artificially challenged with BD1 and BD2 phylotypes with filtrates of tissue containing 0.423 X 109 copies of WSSV per mL resulted a median LT50 value of 73 hrs and 75 hrs, respectively. The in-vivo trial showed higher mean Log WSSV copies (6.47±2.07 per mg tissue) in BD1 challenged shrimp PL compared to BD2 (4.75±0.35 per mg tissue). Crabs infected with BD1 and BD2 showed 100% mortality within 48 hrs and 62 hrs of challenge, respectively with mean Log WSSV copies of 12.06±0.48 and 9.95±0.37 per gram tissue, respectively. Moreover, shrimp antimicrobial peptides (AMPs) penaeidin and lysozyme expression was lower in BD1 challenged group compared to BD2 challenged shrimps. These results collectively demonstrated that relative virulence properties of WSSV based on mortality rate, viral load and expression of host immune genes in artificially infected shrimp PL could be affected by single aa substitution in VP28.

Selective Paste Intrusion (SPI) is an additive manufacturing (AM) process in which thin layers of aggregates are selectively bonded by cement paste only where the structure is to be produced. In this way, concrete elements with complex geometries and structures can be created. Reinforcement is required to increase the flexural strength of the concrete elements and, thus, enable their applicability in practice. Integrating the reinforcement is a difficult task, particularly in the case of SPI due to the layer-wise printing method. Especially with respect to possible complex structures, the production of the reinforcement needs to be adapted to SPI, thereby offering a high degree of freedom. One concept for a reinforcement integration is combining the two additive manufacturing processes SPI and Wire and Arc Additive Manufacturing (WAAM). However, since the two processes serve different fields of application, their compatibility is not necessarily given. Ongoing investigations show that the temperatures caused by WAAM adversely affect both, the cement paste rheology required for sufficient paste penetration into the particle bed and the overall concrete strength. This paper provides an overview of ongoing research focusing on different cooling strategies and their effects on the compressive strength of SPI-printed concrete parts.

Hydrostatic bearings for liquid rocket engine turbopumps provide distinctive advantages including high load capacity even with low viscosity cryogenic fluid and extending a life span by minimizing friction and wear between rotor and bearing surfaces. Application of hydrostatic bearings into turbopumps demands reliable test data base with well-quantified operating parameters and experimentally validated accurate performance predictive tools. The present paper shows the comprehensive experimental data and validation of predicted static load characteristics of hydrostatic journal bearings lubricated with air, water, and liquid nitrogen. Extensive experiments for static load characteristics of hydrostatic bearings are conducted using a turbopump rotor-bearing system simulator while increasing supply pressure (Ps) into the test bearings. The test results demonstrate notable effects of the test fluids and their temperatures, as well as Ps, on the bearing performance. In general, the measured bearing flow rate, rotor displacement, and stiffness of the test bearings steadily increase with Ps. The static load bearing characteristics predictions considering flow turbulence and compressibility matched well with the experimental results. The work with an independent test data and engineering computational programs will further the implementation of hydrostatic bearings in high performance turbopump shaft systems with improved efficiency and enhanced reusability of liquid rocket engine sub-systems.

Maritime transport has become very important due to its ability to internationally unite all continents. In turn, during the last two years, we have observed that the increase of consumer goods has resulted in global shipping deadlocks. In addition, the future goes through the role of ports and efficiency in maritime transport, with the aim of decarbonizing its impact on the environment. In order to improve the economy and people's lives, in this work, we propose to enhance services offered in maritime logistics. To do this, a communications system is designed on the deck of ships to transmit data through a constellation of satellites using interconnected smart devices based on IoT. Among the services, we highlight the monitoring and tracking of refrigerated containers, the transmission of geolocation data from GPS, and security through AIS. This information will be used for a fleet of ships to make better decisions and help guarantee the status of the cargo, as well as maritime safety on the routes. The system design, network dimensioning, and a communications protocol for decision-making will be presented.

Weaving technology can convert two-dimensional structures such as ribbons into three-dimensional structures by specific connections. However, most of the 3D structures fabricated by conventional weaving methods using straight ribbons have some topological defects. In order to obtain smoother continuous 3D surface structures, Baek et al. proposed a novel weaving method using naturally curved (in-plane) ribbons to fabricated three-dimensional curved structures and using this method to weave new spherical weave structures that are closer to perfect spheres. We believe that this new spherical weave structure with smooth geometric properties must correspond to new mechanical properties. To this end, we investigated the buckling characteristics of different types of spherical weave structures by the combination of test and finite element method. The results of calculations and experiments show that the failure mode of the spherical weave structure under vertical loading can be divided into two stages: a flat contact region forms between the spherical weave structure and the rigid plate and inward dimple of ribbons. The spherical weave structures using naturally curved (in-plane) ribbon weaving have better buckling stability than those woven with straight ribbons. The vertical buckling load of spherical weave structures using naturally curved ribbon increases with the width and thickness of the ribbon. In addition, this paper combines test, theoretical and finite element analysis to propose the buckling load equation and buckling correction factor equation for the new spherical weave structure under vertical compression load.

The relaxation process of lithium batteries caused by load variation is considered. It is shown that such processes have strong dependence on internal physical and chemical processes and battery technical conditions. Theoretical expressions of the relaxation process caused by a step-like load variation have been obtained for 1^st and 2^nd order equivalent electrical circuits. The experimental investigations show that the obtained models fit the real relaxation processes and the behavior of the identified parameters could be explained by specific features of physical and chemical processes within the lithium battery. It should be noted that the obtained results can be generalized for a different type of electrochemical power source. The proposed approach makes it possible to provide means for electrochemical power source characterization and diagnostic, the main advantages of which are good time localization of measurement procedures and inexpensive apparatus implementation.

E-commerce platforms created to meet the needs of digital consumers, who are the leading actors of digital-oriented consumption, are increasing rapidly. Revolutionizing our daily lives by offering the digital equivalent of real-world experiences, e-commerce now offers a comfortable shopping experience that transcends the limitations of time and space. This phenomenon has been embraced by individuals spanning all age groups, from young children to the elderly. Structural equation modeling was used in this study, in which the factors affecting online shopping addiction were determined. In this direction, the causal and correlational relationships between the variables of fear of missing out (FoMO), cognitive load, personality types, some socio-demographic characteristics (gender and monthly shopping amount) and online shopping addiction in online shopping were revealed structurally. Since the purposive sampling was used, the study was carried out on 488 people. The goodness-of-fit indices included in the created model were found at an “acceptable” level (χ2/df= 2.248, p=0.000; RMSEA=0.051; GFI=0.878; AGFI=0.856; CFI=0.950; NFI=0.914). These results show that the final version of the model meets the necessary criteria for a good fit, its validity and accuracy. The study revealed the causal and correlational relationship between online shopping addiction and cognitive load, personality types, FoMO, gender, and monthly online shopping amount.

Cellular substructure has been widely observed in the sample fabricated by laser powder bed fusion, while its growth direction and the crystallographic orientation have seldom been studied. This research tries to build a general model to construct the substructure from its two-dimensional morphology. All the three Bunge Euler angles to specify a unique growth direction are determined, and the crystallographic orientation corresponding to the growth direction is also obtained. Based on the crystallographic orientation, the substructure in the single track of austenitic stainless steel 316L is distinguished between the cell-like dendrite and the cell. It is found that, with the increase of scanning velocity, the substructure transits from cell-like dendrite to cell. When the power is 200 W, the critical growth rate of the transition in the single track can be around 0.31 ms^-1.

Background/Objectives: Endometriosis represents substantial direct and indirect healthcare costs impacted by absent accurate, non-invasive uniformly diagnostic tools. We endeavored to demonstrate gastrointestinal myoelectrical activity (GIMA) biomarkers unique to endometriosis allow noninvasive, uniformly accurate diagnosis or exclusion of endometriosis. Methods: Prospective open-label comparative study of 154 patients, age &gt;18, with or without diagnosed endometriosis. Population included 62 non-endometriosis controls (Cohort 1), 43 subjects with surgically histologically-confirmed endometriosis (Cohort 2), and 49 subjects with abdominal pain and negative imaging (Cohort 3). Electroviscerography (EVG) recorded GIMA biomarkers from three abdominal electrodes before and 30-minutes post water-load protocol. Cohort 2 had postoperative EVG and Cohort 3 had preoperative EVG. Calculated specificity, sensitivity, NPV, PPV and predictive probability or C-Statistic used univariate, multivariate, linear and logistical regression analyses of the area under the curve (AUC) at all frequency and time points, including age and pain covariants. Results: Non-endometriosis cohort differed significantly from endometriosis cohorts (p&lt;0.001) for median (IQR), and AUC percent frequency distribution of power at baseline, 10-minute, 20-minute, and 30-minute post water-load at all frequency ranges 15-20cpm, 30-40cpm and 40-50cpm. Endometriosis cohorts were statistically similar (p&gt;0.05). GIMA biomarker threshold scoring demonstrated 95%/91% sensitivity and PPV, 96%/95% specificity and NPV and C-statistic of &gt;99%/98% respectively for age subsets. GIMA biomarkers in Cohort 3 predicted 47/49 subjects positive and 2/49 negative for endometriosis, confirmed surgically. Hormonal therapy, surgical stage, nor pain score affected diagnostic accuracy. Conclusions: Non-invasive electroviscerography with GIMA biomarker detection distinguished participants with and without endometriosis based upon endometriosis specific GIMA biomarkers threshold scoring.

Techniques and tools meant to aid fire management activities in the Cerrado, such as accurately determining fuel load and composition spatially and temporally, are pretty scarce. The need to have fuel information for more efficient management in a considerably heterogeneous, biodiverse, and fire-dependent environment makes a constant search for the improvement of the use of remote sensing techniques in determining fuel characteristics. This study presents the following objectives: (1) to assess the use of data from Landsat 8 OLI images to estimate the fine surface fuel load of the Cerrado during the dry season by adjusting multiple linear regression equations; (2) to estimate fuel load through Random Forest and k-Nearest Neighbor (k-NN) algorithms in comparison with re-gression analyses; and (3) to evaluate the importance of predictor variables from satellite images. Therefore, 64 sampling units were collected, and the pixel values associated with the field plots were extracted in a 3 x 3 pixel window surrounding the reference pixel. For the multiple linear regression analyses, the R² values ranged from 0.63 to 0.78, and the models fitted by the Random Forest al-gorithm ranged from 0.52 to 0.83, while those fitted by k-NN ranged from 0.30 to 0.68. Adopting the Random Forest algorithm resulted in improvements in the statistical metrics of evaluation of the fuel load estimates for Cerrado grassland relative to the multiple linear regression analyses.

The growing number of the accessed energy-efficient frequency conversion air conditioners is likely to generate a large number of harmonics on the power grid. The following shortage in the reactive power of peak load may trigger voltage collapse. Hence, this conflicts with people’s expectations for a cozy environment. Concerning the problems mentioned above, an active management scheme is put forward to balance the electricity use and the normal operation of air conditioning systems. To be specific, schemes to suppress the low voltage ride through (LVRT) and harmonic are designed firstly. Then to deaden the adverse effects caused by nonlinear group load running on the grid, and to prevent the unexpected accidents engendered from grid malfunction, the dynamic sensing information obtained by an online monitor is analyzed, which can be seen as an actively supervise mechanism. The combined application of active and passive filtering technology is studied as well. Thirdly, the new energy storage is accessed reliably to cope with peak-cutting or grid breaking emergencies, and the fuzzy control algorithm is researched. Finally, system feasibility is verified by functional modules co-operation simulation, and active management target is achieved under scientific and reasonable state-of-charge (SOC) management strategy.

Nonlinear catastrophes caused by geological fluids are a fundamental issue in rock mechanics and the geoengineering hazard field. For the consideration of hydrodynamic force on red-bed mudstone softening damage, X-ray visualization test on the fissure flow in mudstone block failure under hydrodynamic force was performed in this study based on block scale and the physical phenomena of fissure seepage and nonlinear diffusion were further explored. A new method for evaluating the hydro-damage degrees of rocks using an X-ray image analysis was proposed, and the quantitative relation of diffusion coefficients of hydro-damage and seepage was established. The research results revealed that the hydrodynamic force promoted the fluid-filled fissure behavior in mudstone specimen failure. Also, the seepage and diffusion phenomena of fluid in rocks during failures were indicated using X-ray imaging. A dual mechanical behavior was presented in the nonlinear seepage and abnormal diffusion of a red mudstone geological body under hydrodynamic conditions. The damaged degree of mudstone was aggravated by the effect of hydrodynamic force, and the initial seepage–diffusion coefficient with respect to lower hydro-damage was larger than the final seepage–diffusion coefficient with respect to higher hydro-damage of rocks with a decreasing nonlinear trend.

The integration of spray drying and agglomeration offers significant advantages, such us continuous production with lower energy consumption. However, it is a knife-edge process with a narrow operating window and limited degrees of freedom that decide between successful agglomeration and fluidized bed blockage due to excessive moisture. In this contribution, factors influencing the spray-through agglomeration process of skim milk powder as a model system were investigated via a design of experiments. Three in-line monitoring methods were applied and tested to observe the most important parameters in the agglomeration process: product moisture and particle size distribution. Regarding the moisture content, a capacitive moisture sensor was calibrated with linear regression and a near-infrared sensor with partial least squares regression. Near-infrared spectroscopy was found to be the suitable method for determining moisture content, while the capacitive moisture sensor mainly provides information on the bulk density, the filling level or fluidization state in the fluidized bed. Additionally, particle size distribution data was extracted from the spectral data using in-line data of a spatial filter velocimetry probe in the fluidized bed. This opens the potential to monitor both parameters in real-time with a single non-invasive sensor.

VHF Data Exchange System (VDES) is considered as an important component of the future maritime communication system by the International Maritime Organization (IMO). On the basis of existing Automatic Identification System (AIS), VDES adds the other two higher capacity subsystems: Application Specific Message (ASM) and VHF Data Exchange (VDE). The Random Access Channel (RACH) of VDE was first introduced in the International Telecommunication Union (ITU) Recommendation M.2092-0. As the slot planning of RACH in VDE is interval, which is significantly different from the continuous slot map for access algorithms in AIS, the existing slot access algorithms cannot meet the requirements of VDE. The simulation results show that the VDE slot map can reduce the normalized throughput of the existing algorithm by 39%. A novel random access algorithm called Adaptive Traffic Load Contention Resolution Diversity Slotted ALOHA (ATL-CRDSA) is proposed in this paper. The algorithm combines the load control strategy and contention resolution scheme to overcome the challenges of the new RACH of VDE. Simulation results show that ATL-CRDSA has remarkable improvement on RACH, and makes RACH very efficient and provides low latency of the packets. The insights gained from this study may be of assistance to the Media Access Control (MAC) layer design for upcoming versions of VDES standard.

The unsteady flow around the monopile under the influence of wave and vibration is studied by numerical method. Based on VOF model and SST Turbulence model, combined with Intermittent Transition model and dynamic mesh method, wave generation and pile vibration in numerical flume are simulated. The flow field around vibrating monopile in a calm water flume and a wave flume is simulated and the simulation results are compared. The calculation results show that the monopile vibration has a great disturbance to the unsteady flow around the pile, and the disturbance degree intensifies with the increase of the vibration amplitude of the monopile: Under the action of inertia, the vibration of the monopile leads to the reattachment of the shedding vortices; Under the influence of the reattachment vortices, the asymmetry of the vorticity on the side wall of the monopile intensifies; The intensification of the disturbance causes the reduction of the phase lead angle of the bed shear stress on the side of the single pile, and an additional high bed shear stress appears on the side of the monopile. In addition, the vortex structure formed alternately around the monopile during the vibration process leads to the periodic change of the high bed shear stress.

Newcastle disease (ND) is a highly contagious and usually causes severe illness that affects Aves all over the world, including domestic poultry. Depending on the virus's virulence, it can impact the nervous, respiratory, and digestive systems and causes up to 100% mortality. The chIFITM genes are activated in response to viral infection. The current study was conducted to quantify the mRNA of chIFITM genes in vitro in response to ND viral infection. It also examined its ability to inhibit ND virus replication in Chicken Embryo Fibroblast (CEF) cells of Aseel and Kadaknath breeds. Results from the study showed that the expression of all chIFITM genes was significantly upregulated throughout the period in the infected CEF cells of both breeds compared to uninfected CEF cells. In CEF cells of the Kadaknath breed, elevated levels of expression of the chIFITM3 gene dramatically reduced the ND viral growth and the viral load was 60% lower than in CEF cells of the Aseel breed. The expression level of the chIFITMs in Kadaknath ranged from 2.39 to 11.68 log2 folds higher than that of control CEFs, and was consistently (p<0.01) higher than Aseel CEFs. Similar to this, IFN-γ gene expresses strongly quickly and peaks at 13.9 log2 fold at 48 hpi. The result suggests that the Kadaknath chicken breed may have a higher level of disease tolerance compared to the Aseel chicken.

Additive manufacturing (AM) technologies show potential for the development of functionally integrated lightweight designs, biomimetic structures and material savings. Typically, as-built surfaces show powder particle agglomerations and re-entrant features, leading to rough surfaces, which are associated with poor fatigue performance. To benefit from the full range of advantages with special focus on aerospace applications, critical features for crack initiation when subjected to fatigue loading need to be identified and mitigated. A first step toward achieving this goal is the surface texture characterisation based on the quantification of surface features. In this paper, selected areal height, functional and feature parameters from ISO 25178-2:2022 are generated and process-specific features are examined for as-built AlSi7Mg0.6 from laser powder bed fusion (PBF-LB). A connection with the particle size distribution of the used powder is demonstrated. It is shown that surface feature analysis opens up opportunities to use physically meaningful surface characteristics in future quality assurance and part qualification processes.

Metal additive manufacturing technologies have large potential for future use in load bearing aerospace applications, requiring a deeper understanding of mechanical performance and influencing factors. The objective of this study is to manufacture fatigue specimens by laser powder bed fusion with comparable bulk and different as-built surface quality (without post-processing). This goal was pursued by using identical bulk/hatch scan parameters while varying contour scan parameters. The bulk quality was evaluated by density measurements according to Archimedes’ principle and tensile testing. The surfaces were investigated using the optical fringe projection method and surface quality was assessed by the areal surface texture parameters Sa (arithmetic mean height) and Sk (core height, derived from material ratio curve). The resulting mean values of max (ultimate tensile strength) were between 375 and 405 MPa, which is a variation of roughly 8%, for seven different surface conditions. It could be confirmed that the influence of contour scan variation on bulk quality is insignificant for the assessed samples.

The Selective Paste Intrusion (SPI) method is a layer-by-layer additive manufacturing technique that allows for the production of complex geometries in concrete elements by selectively bonding aggregates with cement paste in a particle bed. To create reinforced concrete, the Wire and Arc Additive Manufacturing (WAAM) process shall be integrated into SPI. This technique allows the production of almost free-formed reinforcement and thus complements the advantage of SPI to produce free-formed structures of almost any geometry. However, integration of WAAM into SPI poses a considerable challenge, as high temperatures are generated during the welding process. These temperatures can negatively affect the rheological properties of the cement paste, in turn the penetration behavior of the paste in the particle bed and, subsequently, the mechanical properties of the hardened concrete. A possible passive cooling strategy is to increase the protruding length of the reinforcement bars out of the particle-bed. This requires that the distance of the print nozzle to the particle bed is as well increased, since it must be possible to move it across the reinforcement. The objective was thus to investigate the effect of that distance on print quality and to quantify a maximum allowable distance for an adequate print quality (for the printer setting used) in terms of shape accuracy and concrete strength. Compressive and flexural strength tests as well as geometrical measurements using a 3D scanning method were performed on specimen, printed with varying print nozzle to particle bed distances. It can be stated that for the used SPI print-heads, nozzle-types and parameter settings, the distance between the nozzle and the particle bed should not exceed 50 mm to ensure sufficient print quality in both shape accuracy and mechanical strength.

Surfaces of additively manufactured metal parts from powder-based processes typically show powder particle agglomerations and other features, resulting in high surface roughness. Proper characterization of those surfaces is necessary in order to assess part quality with respect to coatability, mechanical performance or corrosion resistance for use in aerospace, automotive, medical and more industrial applications. Optical surface texture measurement allows for collection of areal surface data, while the established contact stylus method only captures line profile data. When applying optical methods for surface topography measurements, proper data acquisition and post-processing in order to assess surface texture may be complex. A number of variables can be adjusted, such as different measurement settings, approaches to outlier removal, evaluated area size or form removal. This work shows the influence of selected z-range prior to measurement and the influence of choosing pre-defined outlier removal settings in MountainsMap 9.2 on selected ISO 25178-2:2022 parameters calculated from data obtained from confocal microscopy for as-built Ti6Al4V from laser powder bed fusion. The aim is to show the influence of variation in measurement and post-processing on calculated surface texture parameters and stress the importance of proper documentation in order to achieve reproducibility of data for quality management.

The Kuznetsk Basin (Kuzbass) is one of the largest coal basins in Siberia and a reference area for the ancient Angaraland continent. The proximity of the Kuzbass and Siberian platform caused their biotic similarities in the Late Palaeozoic. However, due to biota endemism, the Kuzbass Upper Palaeozoic does not correlate directly with the International Chronostratigraphic Chart (ICC). This paper discusses radioisotopic (CA-ID-TIMS) dating of zircons from a volcanic tuff located in the Starokuznetsk Formation. This level matches the interval of the Balakhonka/Kolchugino (B/K) floral change in Kuzbass, i.e. the gradual replacement of cordaitoid-dominated wet forests (Balakhonka flora) by more arid fern-pteridosperm-cordaitoid assemblages (Kolchugino flora). New age (276.9 ± 0.4 Ma) directly correlates the Starokuznetsk Fm with the Upper Kungurian of the ICS. We compared the Kuzbass data with data of the Western Verkhoyanie, where Middle Permian ammonoids (Sverdrupites assemblage) occur in strata recording the B/K floral change. Available (ICC) and new datings indicate the lag between the B/K floral change in low (Kuzbass) and high (Verkhoyanie) latitudes of Angaraland. The B/K floral change in the Kuzbass began in the early Late Kungurian and was completed by the end of this age. In contrast, the B/K floral change in Verkhoyanie began at the end of the Late Kungurian and was completed in the Late Wordian. The delay in the floral changes at different latitudes of Angaraland suggests that existing interregional correlations need further improvement.

Significant design efforts were undertaken during the Pre-Concept Design (PCD) phase of the European DEMO programme to optimize the Helium Cooled Pebble Bed (HCPB) breeding blanket. A gate review was conducted for the entire European DEMO programme at the conclusion of the PCD phase. This article presents a summary of the design evolution and the rationale behind the HCPB breeding blanket concept for the European DEMO. The main performance metrics, including nuclear, thermal hydraulics, thermal mechanical, and tritium permeation behaviors, are reported. These figures demonstrate that the HCPB breeding blanket is a highly effective tritium-breeding and robust driver blanket concept for the European DEMO. In addition, three alternative concepts of interest were explored. Furthermore, this article outlines the upcoming design and R&D activities for the HCPB breeding blanket during the Concept Design phase (2021-2027).

This work discusses the relationship between foreign direct investment (FDI) and pollution in Spain using an autoregressive distributed lag regression model (ARDL) from 1961 to 2018. The authors apply the theoretical context of pollution haven/halo and conclude that FDI in Spain does not contribute to the transfer of green technologies for cleaner production, despite being included within the European environmental regulatory framework. The authors also verify the adequacy of the environmental Kuznets curve (EKC) and the Load Capacity Curve hypothesis (LCC) in the Spanish environmental context and find that income per capita has a positive effect on environmental sustainability and quality. In this sense, the further development of an efficient renewable energy infrastructure could efficiently drive to a better standards all pollution indexes in Spain, including nuclear energy production, contributing the emissions neutrality aimed by the EU by 2050.

Conventional sensors used to measure properties such as deformation or pressure, etc. often make use of metals, ceramics, piezos, and other materials. Many of those materials are very hard, so if they are used as sensors, when the object is deformed, or when the pressure on the object changes from time to time, it is necessary to prepare a variety of sensors with different properties. In this experiment, a dielectric elastomer (DE) pressure sensor was fabricated using a hydrogenated nitrile rubber (HNBR) film with improved hardness and elongation. With this, even very thin film (0.2mm) can be measured at any pressure between 1gf and 20kgf. Previously developed film was harder and less stretchy than the current one, with a pressure detection width from 4 kgf to 120 kgf. This time, however, the pressure sensitivity of the finger has been made more sensitive, making it possible to measure even smaller values. A DE stretch sensor was also developed using single-walled carbon nanotube (SWCNT) electrodes with larger stretchability and flexibility, utilizing this HNBR. This greatly improved the mechanical flexibility and stretchability of the DES. Using this stretch sensor, it became possible to sense the motion of the robot's fingers, and to sense the force (pressure) when the fingertip touched the target object with the DE pressure sensor. In addition, it was confirmed that the sensation of the robot's finger touching an object can be fed back to a human finger by using a small diaphragm type vibrator DE actuator.

The emergence of new SARSCoV-2 variants can affect vaccine efficacy, laboratory diagnosis and therapies already available, triggering interest in the search for antiviral agents for SARSCoV-2 infections. Ribavirin (RBV) is a broad-spectrum antiviral with demonstrated in vitro activity against multiple viruses, including SARSCoV-2. Methods. This retrospective study evaluated the dynamic and viral clearance of SARSCoV-2 in hospitalized adult participants (PTs) with COVID-19 pneumonia who received RBV aerosol within a compassionate use study. Was also assessed the impact of RBV on the clinical outcome and the mutational profile of SARSCoV-2. Results. The median RNA values measured in nine PTs included in the study de-creased from baseline to discharge (at BL, threshold cycle (Ct)=22.4, IQR 19.84-5.07; at discharge, Ct=27.92, IQR 26.43-36.11). Seven/9 PTs experienced a clinical improvement, while two PTs deceased during hos-pitalization. In PTs with a favorable outcome the virus clearance rate at discharge was 28.6%. The cumulative clearance rate was 71.4% within day 14th from discharge. A mutational pattern after RBV was detected in 3/5 PTs in whom was available whole genome sequencing. Conclusions. RBV may limit SARSCOV-2 replication resulting in a favorable clinical outcome. Ribavirin may also contribute to the mutational spectrum of SARSCoV-2.

There are two basic methods for radial external load distribution calculation on rolling elements in a rolling element bearing: the discrete method and the integral method. Solving the discrete equilibrium quasi-static equation using the Newton-Raphson scheme, more accurate results are derived than those based on the integral method, with small theoretical and computational efforts. The Sjövall’s radial integral factors, as well as some approximations proposed in the literature, for line- and point-contacts, are revisited. Numerical approximations for the Sjövall's radial integrals are proposed. The approximations’ errors with respect to the Sjövall’s radial integral’s numerical integration are shown. The numerical results of the displacement between inner and outer rigid rings, maximum hertzian contact deflection and the most loaded element load are shown for some ball and roller bearings, for radial external load ranging from 0 to 10,000 N, and for positive, negative and zero radial clearance, solving the discrete equilibrium quasi-static equation using the Newton-Raphson method. A total of 16 figures is shown in this work, many of which are made up of sub-figures. A total of 58 figures and sub-figures is shown.

The increased demand for resources and energy that is developing with rising global consumption represents a key challenge for our generation. Biogas production can contribute to sustainable energy production and closing nutrient cycles using organic residues or as part of a utilization cascade in the case of energy crops. Compared to hydrogen (H2), biogas with a high methane (CH4) content can be fed into the gas grid without restrictions. For this purpose, the CH4 content of the biogas must be increased from 52 to 60 % after anaerobic digestion to more than 96 %. In this study, biological hydrogen methanation (BHM) in trickling-bed reactors (TBR) is used to upgrade biogas. Design of experiments (DoE) is used to determine the optimal process parameters. The performance of the reactors is stable under all given conditions, reaching a “low” gas grid quality of over 90 %. The highest CH4 content of 95.626 ± 0.563 % is achieved at 55 °C and 4 bar, with a methane formation rate (MFR) of 5.111 ± 0.167 m³/(m³·d). The process performance is highly dependent on the H2:CO2 ratio in the educts, which should be as close as possible to the stochiometric ratio of 4. In conclusion, BHM is a viable approach to upgrade biogas to biomethane quality and can contribute to a sustainable energy grid.

Bridge load testing is crucial in evaluating bridge load-carrying capacity and construction quality. However, conventional techniques have many limitations such as the need for direct contact and low acquisition frequency. This study provides a comprehensive examination of the static and dynamic load tests of a multi-span cable-stayed bridge utilizing a ground-based radar inter-ferometer (GB-radar). The case study was conducted at the Fifth Nanjing Yangtze River Bridge (FNYRB), which is recognized as the world's first lightweight steel-concrete composite cable-stayed bridge, with two spans measuring 600 m. To enhance measurement accuracy, a method was proposed to detect and recover radar phase jumps caused by vehicle motion. Furthermore, precise geometry projection was employed to acquire vertical displacements from GB-radar which were taken along the line-of-sight (LOS) direction. Moreover, during the static load test, a continuous deformation was observed with a maximum pace of 0.31 mm/min, indicating a post-construction settlement caused by soft soil consolidation. This case study highlights the high sampling frequency, high measurement accuracy, and exceptional weatherproof ability of GB-radar, thereby demonstrating its potential to be an alternative to the structural health monitoring (SHM) system.

Floating Offshore Wind Turbine (FOWT) is an innovative technology with little industry guidance for its hull design. Various FOWT floaters with different hull shapes claim to support the same turbines. Structural integrity and material expense analyses of different pontoon shapes were conducted, and it was found that some configurations, such as those with every two columns connected by both pontoon and bracing, have advantages over others. However, it is important to note that the choice of pontoon shape should be based on the wave loading conditions the floater will be exposed to. While a T-shaped pontoon provides a cost-effective solution under certain wave loading scenarios, it may not be the best option for all conditions. Specifically, ring pontoon designs with full bracing were found to be necessary for withstanding certain wave loads. Therefore, it is important to consider different Dominant Load Parameters (DLP) and ensure that a FOWT floater can withstand all applicable DLPs. An uneven hexahedral column shape, which combines the best attributes of square and round shapes, is proposed as a better alternative to cylindrical columns. It offers ease of manufacture and reasonably low drag. Bracing is found to be necessary for withstanding the wind turbine’s incurred moment and forces. The conclusion is that platform design should prioritize manufacturing costs and strength over maximizing hydrodynamic performance.

The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.

In the course of SARS-CoV-2 infection, the 3CL or nsp5 protease plays a pivotal role as the most important viral protease required for the maturation of viral proteins during host infection. Herein, we simulated for 500 ns 3CLproWT, 3CLproH41A, , 3CLproBeta, and 3CLproOmicron, in complex with the substrates nsp 4|5 and nsp 5|6. Our results show that mutations in the 3CLpro present in the SARS-CoV-2 variant of concerns (VOCs) did not lead to significant conformational changes or changes in substrate binding affinities. However, significantly high cleavage rates for the boundary between nsp4 and nsp5 were obtained for 3CLproBeta and 3CLproOmicron and may play a key role in the viral replication and virus fitness gain. Our molecular dynamics data suggest that the cleavage rate of nsp4|5 may be related to the increased amount of viral load observed for these VOCs, releasing more nsp4 than other non-structural proteins. Based on our hydrogen bonding analyses, we also discovered that Gly143 and Glu166 are key residues in substrate recognition, suggesting that these residues may be incorporated as pharmacophoric centers for Beta and Omicron variants in drug design. Our results suggest that Gly143 and Glu166 are essential residues to interact with Gln6 of the different substrates and, therefore, are potential broad-spectrum pharmacophoric centers of SARS-CoV-2 3CLpro.

Based upon 30-years of research by the author a new approach to hospital bed planning and international benchmarking is proposed. The number of hospital beds per 1000 population is commonly used to compare international bed numbers. This method is flawed because it does not consider population age structure or the effect of nearness-to-death on hospital utilization. Deaths are also serving as a proxy for wider bed demand arising from undetected outbreaks of 3000 species of human pathogens. To remedy this problem a new approach to bed modelling has been developed which plots beds per 1000 deaths against deaths per 1000 population. Lines of equivalence can be drawn on the plot to delineate countries with higher or lower bed supply. This method is extended to attempt to define the optimum region for bed supply in an effective health care system. England is used as an example of a health system descending into operational chaos due to too few beds and manpower. The former Soviet bloc countries represent a health system overly dependent on hospital beds. Several countries also show evidence for over-utilization of hospital beds. The new method is used to define a potential range for bed supply and manpower where the current most effective health systems currently reside. The method is applied to total curative beds, medical beds, psychiatric beds, critical care, geriatric care, etc., and can also be used to compare different types of healthcare staff, i.e., nurses, physicians, surgeons. Issues surrounding the optimum hospital size and the optimum average occupancy will also be discussed. The role of poor policy in the English NHS is used to show how the NHS has been led into a bed crisis. The method is also extended beyond international benchmarking to illustrate how it can be applied at a local or regional level in the process of long-term bed planning. Issues regarding the volatility in hospital admissions are also addressed to explain the need for surge capacity and why an adequate average bed occupancy margin is required for an optimally functioning hospital.

Due to related uncertainties brought by changes in energy consumption and the integration of rooftop photovoltaic systems, the accuracy and availability of load profiling data are difficult to achieve. However, project managers and planners use a precise load profile as a crucial tool when determining whether the feeder must be updated or de-loaded. The paper aims to create a non-intrusive monitoring system that predicts the synthetic load profiles behavior of energy consumption using a Light Gradient Boosted and Support Vector Machine (SVM) machine learning technique. The most effective ML algorithm is chosen, and it has the potential to be assessed and verified using validation curves, residuals model generation, and prediction error metrics based on the following key statistical indicators: Mean Absolute Error, Mean Square Error, Root Mean Square Error, R-Square, Root Mean Squared Logarithmic Error, and Mean Absolute Percentage Error. The most effective ML has the potential to be assessed and verified using validation curves, residual model generation, and prediction error metrics based on the following key statistical indicators. The result shows that the estimation of the Irms avg -based on LightGBM is more accurate than the SVM because of its quick, economical, and difficult to overfit, particularly with high-dimensional data, speed, and efficiency of the MAE (3.0698), MSE (15.2757), RMSE (3.9020), RMSLE (0.1433), and MAPE (0.0049) respectively. Additionally, the machine learning model shows that, when compared to the SVM, the LightGBM model had the highest accurate prediction, with R-Square values of 89.8%, 90.3%, and 88.5% for Irms_A_avg, Irms_B_avg, and Irms_C_avg, respectively for Brakfontein Substation supply region, and best represents a diverse customer base.

Clinching is a manufacturing method of mechanical joining two or more materials without the use of heat or additional components. This process relies on high plastic deformation to create a secure bond. Clinching technology is widely used for joining various grades and thickness of materials. Especially in the automotive industry, clinching is an alternative to spot resistance welding. However, the load-bearing capacity of clinched joints is comparatively lower when compared to resistance spot welded joints. This research aimed to enhance the load-carrying capacity of clinched joints. Experimental tests were conducted on clinched joints with locally modified microstructures to optimize their placement within the joint. The microstructure distribution in the clinched joint region was analysed using light and scanning electron microscopy, as well as microhardness measurements. Two material grades, micro-alloyed steels HX420LAD+Z and dual-phase ferritic-martensitic steels HCT600X+Z, were tested. Each grade underwent five groups of ten samples, subject to identical experimental conditions of local heating by resistance spot welding (RSW) and clinching. The application of RSW to the clinched joint area resulted in increase of load-bearing capacity for both joined types of materials.

In this paper, a systematic literature review is presented, through a survey in the main digital databases, about modelling methods for Short-Term Load Forecasting (STLF) for hourly electricity demand for residential electricity and to realize the performance evolution and impact of the Artificial Intelligent (AI) in STLF. With these specific objectives, it was developed a conceptual framework on the subject, a systematic review of the literature based on scientific publications with high impact and a bibliometric study directed to the scientific production of AI and STLF. The review of research articles over a 10-year period, which takes place between 2012-2022, uses the Preferred Reporting Items for Systematic and Meta-Analyses (PRISMA) method. This research resulted in more than 300 articles, available in 4 (four) databases: Web of Science, IEEE Xplore, Scopus and Science Direct. The research was organized around 3 (three) central themes, which were defined through keywords: STLF, Electricity, Residential and their corresponding synonyms. 334 research articles were analyzed and identified the year of publication, journal, author, geography by continent and country and the area of application. Of the 334 documents found in the initial research and after applying the inclusion/exclusion criteria, which allowed delimiting the subject addressed in the topics of interest for analysis, 37 (thirty-seven) documents are in English (25 are journal articles and 12 are conference papers). The results point to a diversity of modelling techniques and associated algorithms. The corresponding performance is measured with different metrics and, therefore, cannot be compared directly. Hence, it should be desirable to have a unified data set together with a set of benchmarks with well-defined metrics for a clear comparison of all the modelling techniques and the corresponding algorithms.

A high-voltage transmission tower consists of structures to avoid the risk of electric shock and to prevent the risk of collapse. Hence, towers are generally designed to be high-rise for efficiency. The main posts of the tower are primary structural members that resist loads under various load conditions. Therefore, the contribution of the secondary member to securing the stiffness and strength of the main posts by reducing the effective buckling length is important. However, there are no detailed design criteria for secondary members. In this study, the structural effects of horizontal members and braces on the torsional stiffness, elastic buckling strength, and load-carrying capacity of transmission towers were observed through various structural analysis methods including linear-elastic, eigenvalue, and geometric nonlinear and inelastic analyses under governing load combinations. According to the analytical study, rather than the horizontal members, the brace spacing significantly affects the structural performance. Therefore, the number of horizontal members can be minimized if sufficient brace members are erected. If the brace spacing is wide, it is recommended that the horizontal members be erected to create K bracing, and the buckling resistance of the main posts can be thus enhanced.