The aim of this work is to compare two softwares (MAUD and TOPAS) based on the Rietveld algorithm and to test the concept of tolerance factor using the dissolution at high temperature of yttrium into BaTiO₃. In general, both softwares give up different values of the crystalline parameters however the trends are similar in most cases but the analysis of the strain and crystallite size in the BaTiO₃ crystals suggests that, in this particular case, MAUD offered results more consistent with the expected behavior. Using the crystalline parameters calculated by Rietveld, the tolerance factor values were obtained and these data suggest even better stability in the crystalline structure than that expected using theoretical parameters. Tolerance factor concept also indicates that Ti⁴⁺ should be preferred.

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.

Multiple studies reported a negative relationship between the Honesty-Humility factor of the HEXACO model and psychopathy. The Durand Adaptive Psychopathic Traits Questionnaire (DAPTQ), which was developed to assess adaptive traits known to be related to psychopathic traits, has previously demonstrate positive relationships with all factors of the Big Five Model, at the exception of a negative relationship with neuroticism. The current study aims to validate the previously reported association between the DAPTQ and the five major components of the personality, while also examining its relationship with the Honesty-Humility factor as defined by the HEXACO model. The results (N = 171) support the good internal consistency, two weeks test-retest validity and inter-correlation of the DAPTQ. A Confirmatory Factor Analysis further supports the nine-factor model of the DAPTQ. When compared to the HEXACO, the DAPTQ did not display any relationship with the Honesty-Humility factor, nor the Agreeableness and Openness factors, but kept its similar association to Emotionality, Extroversion, and Conscientiousness as initially reported in its development phase. Overall, the results support the discriminant validity of the DAPTQ to assess adaptive traits related to the psychopathic personality without overlapping with psychopathic personality traits. Results are discussed in terms of implications and further improvements to validate the DAPTQ.

Polylactic Acid (PLA) is an organic polymer commonly used in fused deposition (FDM) printing and biomedical scaffolding that is biocompatible and immunologically inert. However, variations in source material quality and chemistry make it necessary to characterize the filament and determine potential changes in chemistry occurring as a result of the FDM process. We used several spectroscopic techniques, including laser confocal microscopy, Fourier-Transform Infrared (FTIR) spectroscopy and photoacousitc FTIR spectroscopy, Raman spectroscopy, and X-ray photoelectron Spectroscopy (XPS) in order to characterize both the bulk and surface chemistry of the source material and printed samples. Scanning Electron Microscopy (SEM) and Differential Scanning Calorimetry (DSC) were used to characterize morphology, crystallinity, and the glass transition temperature following printing. Analysis revealed calcium carbonate-based additives which were reacted with organic ligands and potentially trace metal impurities, both before and following printing. These additives became concentrated in voids in the printed structure. This finding is important for biomedical applications as carbonate will impact subsequent cell growth on printed tissue scaffolds. Results of chemical analysis also provided evidence of the hygroscopic nature of the source material and oxidation of the printed surface, and SEM imaging revealed micro and sub-micron scale roughness that will also impact potential applications.

This study presents a new form of velocity distribution in laminar liquid flow in rectangular microchannels using the eigenfunction expansion technique. Darcy friction factor and Poiseuille number are also obtained analytically. Due to the symmetry of the solutions, the effects of changing the aspect ratio from 0 to ∞ are also discussed. Using finite element method (FEM), the obtained analytical results are further compared with the 3D numerical simulations for the rectangular microchannels with different range of aspect ratio and pressure gradient, and excellent agreements were found. These findings provide additional insights in interpreting the results of the pressure-driven flows in finite aspect ratio microchannels, in which very precise comparison with the macroscale theory is crucial.

A via ferrata (from the German “klettersteig”, hereinafter VF) is a sports route located on forest and mountains vertical rock walls equipped with steps, chains, artificial dams, bridges and other fixed elements and which have a steel cable (safety cable) all the way along allowing users to secure their progress and avoid possible falls [1]. This article aims to analyse the state of the art of the VF sector in Spain, especially in terms of the regulations of obligatory compliance, in addition to defining the basic characteristics of the installations to ensure that these are safe for users, providing a previously non-existent summary of the most important recommendations regardless of the country where they are installed.

The objective of this study was to investigate the concentration and spatial distribution patterns of six potentially toxic heavy metal elements (Mn, Zn, Cr, Pb, Cu and Ni) in bus station dusts in the Xifeng district of Gansu province, NW China. The contents were analyzed for Mn, Zn, Cr, Pb, Cu and Ni by using S8 TIGER Brochures wavelength dispersive X-ray fluorescence spectrometry. Geoaccumulation index (Igeo ), enrichment factor (EF), pollution index (PI) and integrated pollution index(IPI) were calculated to evaluate the heavy metal contamination level of bus station dusts. The results indicate that, in comparison with the background values of local soil, bus station dusts in Xifeng have elevated metal concentrations as a whole. The concentrations of heavy metals investigated in this paper are compared with the reported data of other cities. The results show that the arithmetic means of Mn, Zn, Cr, Pb, Cu and Ni are 440.8, 137.9, 60.0, 42.8, 33.5 and 19.8mg kg−1 respectively. The mean values of Igeo reveal the order of Ni<Mn<Cr<Cu<Zn<Pb. The high Igeo and EF for Cu, Zn and Pb in bus station dusts indicate that there is a considerable Cu, Zn and Pb pollution, which mainly originate from traffic and industry activities. The Igeo and EF of Ni, Mn and Cr are low and the assessment results indicate an absence of distinct Ni, Mn and Cr pollution in bus station dusts. The assessment results of PI also support Cu, Zn and Pb in bus station dusts presented middle pollution, and IPI indicates heavy metals of bus station dusts polluted seriously.

The aim of this research was to investigate the mass, substances and energy flow through two-stroke low speed Diesel engines. For this reason, a zero-dimensional model of the combustion in the engine was developed with a calculated amount and composition of exhaust gases. Due to the large amount of oxygen in the exhaust gases, a ratio of real air consumption and stoichiometric amount of air required for combustion of injected fuel was set. The calculated ratio showed that the engine consumes four times more air than needed for combustion in AFR_stoich. In this work it is called the Air Consumption Factor or Ratio and has not been mentioned in scientific literature before. Air Consumption Ratio is defined as a factor of dry or humid air. To be more comprehensive, a modified diagram of composition of the flow in and out of a two-stroke fuel injection engine and the cylinder was drawn.

For many decades, X-ray diffraction (XRD) has been used for material characterization. With the recent development in material science understanding and technology, various new materials are being developed, which requires upgrading the existing analytical techniques such that intricate problems can be solved. Although, XRD is a well-established non-destructive technique, it still requires further improvements in its characterization capabilities, especially when dealing with complex mineral structures. The present review conducts comprehensive discussions on atomic crystal structure, XRD principle, its applications, uncertainty during XRD analysis, and required safety precautions, all in one place. It further discusses the future research directions, especially the use of artificial intelligence and machine learning tools for improving the effectiveness and accuracy of XRD technique for mineral characterization. It has been focused that how XRD patterns can be utilized for a thorough understanding of the crystalline structure, size, and orientation, dislocation density, phase identification, quantification, and transformation, information about lattice parameters, residual stress, and strain, and thermal expansion coefficient of materials. All these important discussions on XRD for mineral characterization are compiled in this short yet comprehensive review that would benefit specialists and engineers in the chemical, mining, iron, metallurgy, and steel industries.

This paper presents a two-stage ADC based on pseudo-differential operational transconductance amplifier (OTA), which is designed for the readout circuit of X-ray linear array sensor. This hybrid ADC employs an incremental sigma-delta ADC and a cyclic ADC, achieving a good trade-off between accuracy and conversion speed. The two stages share the same hardware to reduce power consumption and die area. A common-mood feedback module is used to suppress the influence of charge injection, and the effectiveness is demonstrated by detailed theoretical analysis. A test chip of 14-bit ADC is fabricated in 0.35μm CMOS technology. The measured root mean square (RMS) value of DNL is 0.254 LSB, and the maximum value of INL is -0.776/+1.56 LSB. The measured effective number of bits (ENOB) is 13.43 bits.

To screen and validate immunosuppressive factors in luminal- and basal-like breast cancer cell lines and tissue samples associated with malignant phenotypes. The mRNA microarray datasets, GSE40057 and GSE1561, were downloaded and remodelled. Differentially expressed genes (DEGs) were identified. Enrichment analyses performed and the online resources, GOBO and Kaplan-Meier Plotter, were employed to screen for immunosuppressive factors associated with breast cancer malignant phenotypes. qRT-PCR and western blot were used to validate the expression of CD274 and IL8 in cell lines and immunohistochemical detected the MIF and VEGFA on tissue microarrays. The results showed that CD274 and IL8 were both upregulated in basal-like cell lines. That MIF expression was dramatically increased in patients with breast cancer metastases (p<0.05) and that VEGFA expression positively correlates with breast cancer pathologic grade (p<0.05).During the formation and development of breast cancer, immune-related genes are always activated, and immunosuppressive factors CD274, IL8, MIF and VEGFA are upregulated. Such molecules could be used as biomarkers for breast cancer prognosis. However, because individual immune-related factors can play several biological roles, the mechanistic relationship between immunosuppressive factors and breast cancer malignant phenotypes and the feasibility of their application as drug targets require further investigation.

This study investigated the neuroprotective effects of methyl 3,4-dihydroxybenzoate (MDHB) against t-butylhydroperoxide(TBHP) induced oxidative damage in SH-SY5Y (human neuroblastoma cells) and the underlying mechanisms. SH-SY5Y were cultured in DMEM+10% FBS for 24 hours and pretreated with different concentrations of MDHB or N-acetyl-L-cysteine (NAC) for 4 hours prior to the addition of 40 μM TBHP for 24 hours. Cell viability was analyzed using the methyl thiazolyl tetrazolium (MTT) and lactate dehydrogenase (LDH) assays. An annexin V-FITC assay was used to detect cell apoptosis rate. The 2',7'-dichlorofluorescin diacetate (DCFH-DA) assay was used to determine intracellular ROS levels. The activities of antioxidative enzymes (GSH-Px and SOD) were measured using commercially available kits. The oxidative DNA damage marker 8-OHdG was detected using ELISA. Western blotting was used to determine the expression of Bcl-2, Bax, caspase 3, p-Akt and Akt proteins in treated SH-SY5Y cells. Our results showed that MDHB is an effective neuroprotective compound that can mitigate oxidative stress and inhibit apoptosis in SH-SY5Y cells

Hepatitis B virus (HBV) is the dominant risk factor for hepatocellular carcinoma (HCC). HBV X protein (HBx) plays crucial roles in HCC carcinogenesis. HBx interferes with several signaling pathways including Notch1 pathway in HCC. In our study, we found that Notch1 was highly expressed in HCC especially in large HCC. Notch1 and HBx co-localized in HCC and their levels were positively correlated with each other. Notch1 expression was more elevated in HepG2.2.15 than that in HepG2. HBx activated Notch1 pathway in HepG2.2.15. Repression of HBx and Notch1 pathway attenuated the growth of HepG2.2.15. Notch1, ERK and AKT pathways were inhibited after a γ-secretase inhibitor treatment. Dual-specificity phosphatase 1 (DUSP1) and phosphatase and tensin homolog (PTEN) were up-regulated after the γ-secretase inhibitor treatment and Hes1 inhibition. Luciferase reporter assays showed that Hes1 repressed the promoters of DUSP1 and PTEN and this was reverted by γ-secretase inhibitor treatment. Western blotting demonstrated that DUSP1 dephosphorylated pERK and PTEN dephosphorylated pAKT. Collectively, we reported a link among HBx, Notch1 pathway, DUSP1/PTEN, and ERK/AKT pathways, which influenced HCC cell survival and could be a therapeutic target for HCC.

The XChem facility at Diamond Light Source offers fragment screening by X-ray crystallography as a general access user program. The main advantage of X-ray crystallography as a primary fragment screen is that it yields directly the location and pose of the fragment hits, whether within pockets of interest or merely on surface sites: this is the key information for structure-based design and for enabling synthesis of follow-up molecules. Extensive streamlining of the screening experiment at XChem has engendered a very active user programme that is generating large amounts of data: in 2017, 36 academic and industry groups generated 35,000 datasets of uniquely soaked crystals. It has also generated a large number of learnings concerning the main remaining bottleneck, namely obtaining a suitable crystal system that will support a successful fragment screen. Here we discuss the practicalities of generating screen-ready crystals that have useful electron density maps, and how to ensure they will be successfully reproduced and usable at a facility outside the home lab.

The air side thermal hydraulic performance of multi-louvered aluminium fin heat exchangers is investigated. A detailed study was performed to analyse the thermal performance of air over a wide range of Reynolds number i.e. from 30 to 250. Air-side heat transfer coefficient and air pressure drop were calculated and validated over the mentioned band of Reynolds numbers. Critical Reynolds number was determined numerically and the variation in flow physics along with the thermal and hydraulic performance of microchannel heat exchanger associated with R_cri has been reported. Moreover, a parametric study of the multi-louvered aluminium fin heat exchangers was also performed for 36 heat exchanger configurations with the louver angles (19-31°), fin pitches (1.0, 1.2, 1.4 mm) and flow depths (16, 20, 24 mm); and the geometric configuration exhibiting the highest thermal performance was reported. The air-side heat transfer coefficient and pressure drop results for different geometrical configurations were presented in terms of Colburn j factor and Fanning friction factor f, as a function of Reynolds number based on louver pitch.

The driving force behind adopting the idea of ​​sustainable development are producers and retailers. Unfortunately, when preparing their product range for consumers, many of them still only pay attention to the size of the customers’ earnings, how often they shop and how much they buy when shopping. In consumer segmentation, sustainable values ​​that consumers apply when making their purchasing decisions are rarely taken into account. The aim of this article is to show that values ​​such as environmental protection, the ethical behaviour of producers, fair trade or maximising the utility function of consumption are so important in the purchasing process in the coffee market that they can be used as segmentation variables. The Polish coffee market was selected to carry out segmentation taking into account the consumers' sustainable values. The main source of the article is the results of a standardized online survey conducted on a nationwide sample of 800 coffee consumers in July 2018. Multi-dimensional analyses such as extrapolative factor analysis (EFA) and cluster analysis (CA) were used to describe the obtained results. As a result, six segments of coffee consumers were identified and described: “responsible, aspiring to be connoisseurs”, “loyal coffee enthusiasts”, “pragmatic users”, “coffee laypersons”, “sophisticated connoisseurs”, “consumerists, connoisseurs, but not at any price”. Among the identified segments, the sustainable consumption values ​​most often mentioned refer to "responsible, aspiring to be connoisseurs", and the least often - ”consumerists, connoisseurs, but not at any price”. The conclusions presented in the last part of the article may be used by manufacturing and trade enterprises, operating on the coffee market, in order to respond to the identified needs and expectations of consumers and by governmental and social organisations so as to determine the directions of pro-ecological education of consumers.

Wind power output is highly dependent on the wind speed at the selected site, therefore wind-speed distribution modeling is the most important step in the assessment of wind energy potential. This study aims at accurate evaluation of onshore wind energy potential in seven coastal cities in the south of Iran. Six Probability Distribution Functions (PDFs) were examined over representative stations. It has been deduced that the Weibull function, which was the most used PDF in similar studies, was only applicable to one station. Here, Gamma offered the best fit for three stations and for the other ones, Generalized Extreme Value (GEV) performed better. Considering the ranking of six examined PDFs and the simplicity of Gamma, it was identified as the effective function in the southern coasts of Iran bearing in mind the geographic distribution of stations. Besides, six turbine power curve functions were contributed to investigate the capacity factor. That was very important, as using only one function could cause under- or over-estimation. Then, stations were classified based on the National Renewable Energy Laboratory system. Last but not least, examining a range of wind turbines enabled scholars to extend this study into the practice and prioritize development of stations considering budget limits.

This research is related to the eco-hydrological problems of herbaceous wetland drying and biodiversity loss in the floodplain lakes of the Middle Basin of the Biebrza river (Poland). An experiment was set up, whose main goals were: (i) mapping the vegetation types and the temporarily or permanently flooded areas, and (ii) comparing the usefulness of C-band Sentinel-1A (S1A) and X-band TerraSAR-X/TanDEM-X (TSX/TDX) for mapping purposes. The S1A imagery was acquired on a regular basis using the dual polarization VV/VH and the Interferometric Wide Swath Mode. The TSX/TDX data were acquired in quad-pol, a fully polarimetric mode, during the Science Phase. The paper addresses the following aspects: i) wetland mapping with S1A multi-temporal series; ii) wetland mapping with fully polarimetric TSX/TDX data; iii) comparing the wetland mapping using dual polarization TSX/TDX subsets, i.e. HH-HV, HH-VV and VV-VH; iv) comparing wetland mapping using S1A and TSX/TDX data based on the same polarization (VV-VH); v) studying the suitability of the Shannon Entropy for wetland mapping; and vi) assessing the contribution of interferometric coherence for wetland classification. The experimental results show main limitations of the S1A dataset, while they highlight the good accuracy that can be achieved using the TSX/TDX data, especially those taken in fully polarimetric mode.

Background: A significant proportion of SARS-CoV-2-infected patients develops respiratory failure. Thromboembolism is also prevalent in coronavirus disease 2019 (Covid-19). Vitamin K plays a role in coagulation and possibly also in lung diseases. We therefore hypothesized that vitamin K is implicated in Covid-19 pathogenesis. Methods: 134 Covid-19 patients and 184 controls were included. Inactive vitamin K-dependent matrix Gla protein (i.e.dp-ucMGP) and prothrombin (i.e. PIVKA-II) were measured, which are inversely related to respectively extrahepatic and hepatic vitamin K status. Desmosine was measured to quantify elastic fiber degradation. Lung involvement and arterial calcifications severity were assessed by computed tomography. Results Dp-ucMGP was elevated in Covid-19 patients compared to controls (P=0.001). Higher dp-ucMGP was found in Covid-19 patients with poor compared to better outcomes (P=0.002). PIVKA-II was normal in 81.8%, mildly elevated in 14.0% and moderately elevated in 4.1% of Covid-19 patients not using vitamin K antagonists. Dp-ucMGP in Covid-19 patients was correlated with desmosine (P<0.001), thoracic aortic calcification (P<0.001) but not with pneumonia severity. Conclusions: Extrahepatic vitamin K status was severely reduced in Covid-19 patients, as reflected by elevated inactive MGP, and related to poor outcome. Procoagulant prothrombin activity remained preserved in the majority of Covid-19 patients, which is compatible with the increased thrombogenicity that is frequently observed in severe Covid-19. Impaired MGP activation was linked to accelerated elastic fiber degradation and premorbid vascular calcifications. A trial should assess whether increasing MGP and protein S activity by vitamin K administration improves Covid-19 outcomes.

The features of a class of cubic curves with a shape factor are analyzed by means of the theory of envelope and topological mapping. The effects of the shape factor on the cubic curves are made clear. Necessary and sufficient conditions are derived for the curve to have one or two inflection points, a loop or a cusp, or to be locally or globally convex. Those conditions are completely characterized by the relative position of the edge vectors of the control polygon and the shape factor. The results are summarized in a shape diagram, which is useful when the cubic parametric curves are used for geometric modeling. Furthermore we discussed the influences of the shape factor on the shape diagram and the ability for adjusting the shape of the curve.

Liver X receptors (LXR) are deemed as potential drug targets for atherosclerosis, whereas a role in adipose tissue expansion and its relation to insulin sensitivity remains unclear. To assess the metabolic effects of LXR activation, C57BL/6 mice on a high-fat diet (HFD) were treated with the dual LXRα/β agonist T0901317 (30 mg/kg per day) for 3 weeks. Differentiated 3T3-L1 was used for analysing the effect of T0901317 on glucose uptake.T0901317 reduced fat mass, accompanied by a massive fatty liver and lower adipokine levels in circulation of HFD mice. Increased adipocyte apoptosis and macrophage infiltration were found in epididymal fat of T0901317-treated HFD mice. In addition, T0901317 treatment promoted basal lipolysis, but blunted the anti-lipolytic action of insulin. Furthermore, LXR activation antagonized PPARγ target genes in epididymal fat and PPARγ-PPRE binding activity in 3T3-L1 adipocytes. Although the glucose tolerance was comparable to that in vehicle-treated HFD mice, the insulin tolerance was significantly decreased in T0901317-treated HFD mice, indicating decreased insulin sensitivity by T0901317 administration, and which was further supported by impaired insulin signalling found in epididymal fat and decreased insulin-induced glucose uptake in 3T3-L1 by T0901317administration. These findings reveal that LXR activation impairs adipose expansion which contributes to decreased insulin sensitivity.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

Cronbach’s (1957) famous division of scientific psychology into two disciplines is still actual for the fields of cognition (general mechanisms) and intelligence (dimensionality of individual differences). The welcome integration of the two fields requires the construction of mechanistic models of cognition and cognitive development that explain key phenomena in individual differences research. In this paper we argue that network modeling is a promising approach to integrate the processes of cognitive development and (developing) intelligence into one unified theory. Network models are defined mathematically, describe mechanisms on the level of the individual, and are able to explain positive correlations among intelligence subtest scores - the empirical basis for the well-known g-factor - as well as more complex factorial structures. Links between network modeling, factor modeling and item response theory allow for a common metric, encompassing both discrete and continuous characteristics, for cognitive development and intelligence.

Poly(2,6-dimethyl phenyl oxide) (PPO) is known for its low dissipation factor. To achieve insulating materials with low dissipation factor for high-frequency communication application, a monomer-type benzoxazine (P-APPO) and a main-chain-type benzoxazine (BPA-APPO) were prepared from an amine end-capped oligo (2,6-dimethyl phenylene oxide) (APPO). The APPO was prepared from a nucleophilic substitution of a phenol-end capped oligo (2,6-dimethyl phenylene oxide) (a commercial product, SA 90) with fluoronitrobenzene, and followed by catalytic hydrogenation. After self-curing or curing with a dicyclopentadiene-phenol epoxy (HP 7200), thermosets with high-T_g and low-dissipation factor can be achieved. Furthermore, the resulting epoxy thermosets show better thermal and dielectric properties than those of epoxy thermoset cured from its precursor SA90, demonstrating it is a successful modification in simultaneously enhancing the thermal and dielectric properties.

World is now experiencing a major health calamity due to the coronavirus disease (COVID-19) pandemic, caused by the severe acute respiratory syndrome coronavirus clade 2 (SARS-CoV- 2). The foremost challenge facing the scientific community is to explore the growth and transmission capability of the virus. Use of artificial intelligence (AI), such as, deep learning, in (i) rapid disease detection from x-ray/computerized tomography (CT)/ high-resolution computed tomography (HRCT) images, (ii) accurate prediction of the epidemic patterns and their saturation throughout the globe, (iii) identification of the epicenter in each country/state and forecasting the disease from social networking data, (iv) prediction of drug-protein interactions for repurposing the drugs, and (v) socio-economic impact and prediction of future relapses, has attracted much attention. In the present manuscript, we describe the role of various AI-based technologies for rapid and efficient detection from CT images complementing quantitative real time polymerase chain reaction (qRT-PCR) and immunodiagnostic assays. AI-based technologies to anticipate the current pandemic pattern, possibility of future relapses and socio-economic impact are also discussed. We inspect how the virus transmits depending on different factors, such as, population density and mobility among others. We depict how AI-based mobile app for contact tracing and surveys can prevent the transmission. A modified deep learning technique can assess affinity of the most probable drugs to treat COVID-19. Here a few effective antiviral drugs, such as, Geneticin, Avermectin B1, and Ancriviroc among others, have been reported with their appropriate validation from previous investigations.

A Natural gas is increasingly being sought after as a vital source of energy, given that its production is very cheap and does not cause the same environmental harms that other resources, such as coal combustion, do. Understanding and characterizing the behavior of natural gas is essential in hydrocarbon reservoir engineering, natural gas transport, and process. Natural gas compressibility factor, as a critical parameter, defines the compression and expansion characteristics of natural gas under different conditions. In this study, a simple second-order polynomial model based on the group method of data handling (GMDH) is presented to determine the compressibility factor of different natural gases at different conditions, using corresponding state principles. The accuracy of the model evaluated through graphical and statistical analyses. The results show that the model is capable of predicting natural gas compressibility with an average absolute error of only 2.88%, a root means square of 0.03, and a regression coefficient of 0.92. The performance of the developed model compared to widely known, previously published equations of state (EOSs) and correlations, and the precision of the results demonstrates its superiority over all other correlations and EOSs.

This paper generalizes the actuator disc theory to the application of crosswind kite power systems. For simplicity, it is assumed that the kite sweeps an annulus in the air, perpendicular to the wind direction (i.e. straight downwind configuration with tether parallel to the wind). It is further assumed that the wind flow has a uniform distribution. Expressions for power harvested by the kite is obtained, where the effect of the kite on slowing down the wind (i.e. the induction factor) is taken into account. It is shown that although the induction factor may be small for a crosswind kite (of the order of a few percentage points), neglecting it in calculations may result in noticeable overestimation of the amount of power harvestable by a crosswind kite system.

Data generation using high throughput technologies has led to the accumulation of diverse types of molecular data.These data have different types (discrete,real,string etc.) and occur in various formats and sizes. Datasets including gene expression, miRNA expression, protein-DNA binding data (ChIP-Seq/ChIP-ChIP), mutation data(copy number variation, single nucleotide polymorphisms), GO annotations, protein-protein interaction and disease-gene association data are some of the commonly used genomic datasets to study biological processes. Each of them provides a unique, complementary and partly independent view of the genome and hence embed essential information about their regulatory mechanisms. In order to understand the functions of genes, proteins and analyze mechanisms arising out of their interactions, information provided by each of these datasets individually may not be sufficient. Therefore integrating these multi-omic data and inferring regulatory interactions from the integrated dataset provides a system level biological insights in predicting gene functions and their phenotypic outcomes. To study genome functionality through interaction networks, different methods have been proposed for collective mining of information from an integrated dataset. We survey here data integration approaches using state-of-the-art techniques such as network integration, Bayesian networks, regularized regression (LASSO) and multiple kernel learning methods.

Coronavirus disease 2019 (COVID-19) is caused by infection with the 2019 novel coronavirus 2 (2019-nCoV, now referred to as SARS-CoV-2). COVID-19 has become a global pandemic since its outbreak at the end of Dec 2019. COVID-19 could lead to severe acute respiratory disease, especially to those who have reduced immunity. Binding of the viral Spike protein (S) to its receptor ACE2 (Angiotensin Converting Enzyme 2) on the surface of target cells has been proven to be key for virus entry and infection. Although ACE2 expression in the respiratory system is necessary for pneumonia infection by SARS-CoV-2, the regulation of ACE2 gene expression remains poorly investigated, especially for patients that are in pre-pathological conditions. Here, by analyzing The Gene Expression Omnibus (GEO) database, we investigated the expression regulation of ACE2 in various kinds of primary epithelial cells from the respiratory system after varies of respiratory viruses infection such as influenza A virus (IFV), respiratory syncytial virus (RSV) and human rhinovirus (hRV). Our analyses reveal that infection of multiple kinds of respiratory viruses or influenza vaccines greatly increased ACE2 expression, suggesting that respiratory viruses infection could represent a high risk factor for developing COVID-19. We also found that the regulatory effect of influenza A virus on ACE2 expression is associated with activation of the interferon beta-induced pathway and viral RNA-activated host response. Together, our data provide a theoretical framework for clinical classification for SARS-CoV-2 infection susceptibility and could be used for future prevention and therapy treatment for COVID-19.

Background: Dengue incidence has grown dramatically around the world in recent years. It transmitted by Aedes mosquitoes. Many factors contributed to the vector densities such as environmental and sociological factors. Objective: This study is aimed at determining the environmental and sociological factors contributing to dengue cases. Methods: The study used questionnaire survey involving 379 respondent with dengue history. Result: The study showed that there is significant association between the time departs to work and mobility of respondents (95%CI = 2.779 and 5.594, p < 0.0001). Similarly, there is significant association between the time of arrival to work and mobility of respondents (95%CI = 1.617 and 2.155, p < 0.0001). Moreover, the type of housing and the surrounding vegetation were the environmental factors that showed significant values; p = 0.023, and p = 0.017. Conclusion: The study indicated the factors contributed are patient who lived in independent houses and the time of mobility patient.

This study examines the evolution of the two-factor authentication method and its adaptability to the online education system. Two-factor authentication is a security measure used especially in areas where information such as banking is valuable. Parallel to technological developments, it has developed as much as daily. It aims to take security one step forward because it is composed of two phases. Today, banking, IOT devices, public transport tickets and many other areas are used. Two-factor authentication methods against security attacks in the field of information are also being updated. In recent years, new technologies such as biometric (iris pattern, retinal pattern, etc.) or behavioral biometry (location tracking, walking information, touch speed etc.) were studied. Instead of physically studying somewhere like going to a course in modern society, online trainings become more advantageous. Most of these online trainings are given certificates such as participation certificate, success certificate, etc. The main problem here is whether the person who is being certified is true. In the study conducted in line with these details, there is a proposal for the application of the Mimic Control Method with Sound Intensity (MCMSI) method for on-line training by examining the two-factor authentication techniques up to the day.

It has been declared repeatedly that cancer is a result of molecular genetic abnormalities. However, there has been no working model describing the specific functional consequences of the deranged genomic processes that result in the initiation and propagation of the cancer process during carcinogenesis. We no longer need to question whether or not cancer arises as a result of a molecular genetic defect within the cancer cell. The legitimate questions are: how and why? This article reviews the preeminent data on cancer molecular genetics and subsequently proposes that the sentinel event in cancer initiation is the aberrant production of fused transcription activators with new molecular properties within normal tissue stem cells. This results in the production of vital oncogenes with dysfunctional gene activation transcription properties, which leads to dysfunctional gene regulation, the aberrant activation of transduction pathways, chromosomal breakage, activation of driver oncogenes, reactivation of stem cell transduction pathways and the activation of genes that result in the hallmarks of cancer. Furthermore, a novel holistic molecular genetic model of cancer initiation and progression is presented along with a new paradigm for the approach to personalized targeted cancer therapy, clinical monitoring and cancer diagnosis.

Georgia is ranked fifth highest among states for rates of HIV diagnosis. About 4% of persons living with HIV infection in the United States reside in Georgia, and almost 19% of these people do not know their HIV status. The present study examined the trends and associated factors of HIV testing among adults in Georgia between 2010 and 2014 by analyzing data of the Behavioral Risk Factor Surveillance System (BRFSS). A total of 30,791 persons aged ≥18 years were identified who responded to the question “Have you ever been tested for HIV?” Overall, there were 11,543 respondents who had been tested for HIV, with a decrease in percentage from 49.4% in 2010 to 43.7% in 2014 (p<0.001). Factors associated with HIV testing were being black (p<0.001), being younger than 55 years (p<0.001), single (p=0.02), attaining education level above high school (P<0.001), engaging in HIV high-risk behaviors (p<0.001), and not having healthcare coverage (p=0.03). Overall in Georgia, there has been a decline in the temporal trend of HIV testing, and more than half of adults have never been tested for HIV. For reducing HIV transmission in Georgia, enhancing access and utilization of HIV testing should be a public health priority.

Levels of trace element pollution in surface soil can be estimated using soil analyses and leaching tests. These methods may reveal different results due to the effect of soil properties, such as grain size and mineral composition, on elemental availability. Therefore, this study advocates an alternative method for monitoring and assessment of trace element pollution in surface soil using terricolous fruticose lichens. Lichens growing at abandoned mine sites and unpolluted areas in southwest Japan and their substrata were analyzed using inductively coupled plasma-mass spectrometry and X-ray fluorescence spectrometry to clarify the relationships between Cu, Zn, As, and Pb concentrations in lichens and soils, including their absorption properties. Concentrations of these elements in the lichens were positively correlated with those in the soils regardless of lichen species, location, habitat, or conditions of soils. The analyzed lichens had neither competitive nor antagonistic properties in their elemental absorption, which made them good biomonitors of trace element pollution in surface soil. The distribution maps of average Cu, Zn, As, and Pb concentrations at each sampling region detected almost all of the Cu, Zn, and As pollution of the soils. Therefore, lichens could be used in practical applications to monitor Cu, Zn, and As pollution in surface soils.

Aim: To analysis the relationship between healthy adults right ventricular diameter (RVD) and geographical factors. Location: China’s 22 provinces, municipalities and autonomous regions. Methods: Using correlation analysis the relationship between RVD and nine geographic factors, build predictive models by factor analysis. Results: There is significant correlation between RVD and geographical factors, and the annual average temperature is most relevant geographical factors, a predictive model was built by factor analysis: Ŷ = 19.46 + 0.0007072X1 + 0.001034X2 -0.05412X3 -0.001405X4 -0.0006351X5 + 0.02903X6 + 0.01243X7 -0.01033X8 + 0.03816X9 ± 0.63. Then using Kriging interpolation interpolate the geographical distribution of Chinese healthy adult right ventricular diameter reference value in ArcGIS software. Main Conclusion: If geographic factors can be derived in anywhere of China, RVD can be calculated by the model, you can also get RVD from geographical distribution.

Using DCC-GARCH and EGARCH model, this paper finds that since 1990, the relationship between crude oil prices and the US dollar index is time-varying, demonstrating a process of “very weak correlation—negative correlation—enhanced negative correlation—weakening negative correlation”, but the existing research does not provide enough reasonable explanation. Therefore, this paper proposed a “key mediating factors” hypothesis which points out that whether there is a common “key mediating factor” is important source of the time-varying relationship between two assets. We argue that market trend and financial market sentiment undertook the role of “key mediating factor” during the period of “2002 to the financial crisis” and “financial crisis to 2013”, while other periods lack the “key mediating factors”.

Based on stochastic frontier analysis and translog input distance function, this paper examines the total factor energy efficiency of China’s industry using input-output data of 30 sub-industries from 2002 to 2014, and decomposes the changes in estimated total factor energy efficiency into the effects of technical change, technical efficiency change, scale efficiency change and input-mix effect. The results show that during this period the total factor energy efficiency in China’s industry grows annually at a rate of 3.63%, technical change, technical efficiency change and input-mix effect contribute positively to the change in total factor energy efficiency, while scale efficiency change contributes negatively to it.

Maghemite (γ-Fe2O3) is a mineral formed from magnetite oxidation at low temperatures, an intermediate metastable term of the magnetite to hematite oxidation and could be mixed with both. It has magnetic susceptibility similar to magnetite, crystal structure close to magnetite with which it forms a solid solution, while compositionally it equals hematite. Maghemite is thus easily misidentified as magnetite by X-ray diffraction and/or as hematite by spot chemical analysis in iron ore characterization routines. Nonstoichiometric magnetite could be quantified in samples of Brazilian soils and iron ores by the Rietveld method using a constrained refinement of the X-ray patterns. The results were confirmed by reflected light microscopy and Raman spectroscopy, thus qualitatively validating the method. X-ray diffraction with the refinement of the isomorphic substitution of Fe2+ by Fe3+ along the magnetite-maghemite solid solution could help to suitably characterize maghemite in iron ores, allowing for the evaluation of its ultimate influence on mineral processing, by affecting its surface and breakage properties.

The present study aimed to analyze novel mechanisms underlying Nrf2-mediated anti-apoptosis in periodontal ligament stem cells (PDLSCs) in the periodontitis oxidative microenvironment. We created an oxidative stress model with H2O2-treated PDLSCs. Herein, we used real-time PCR, western blotting, TUNEL staining, fluorogenic assay and transfer genetics to confirm the degree of oxidative stress and apoptosis as well as the Nrf2 function. Surprisingly, we demonstrated that with up-regulated ROS and MDA levels, the effect of oxidative stress was obvious under H2O2 treatment. Anti-oxidative molecules were changed after the H2O2 exposure, whereby the anti-oxidative signaling of Nrf2 was activated with the increase of its downstream effectors, HO-1, NQO1 and γ-GCS. Additionally, the apoptosis levels gradually increased with oxidative stress and changes in the caspase-9, caspase-3, Bax and c-Fos levels, but not with caspase-8 and down-regulated Bcl-2. The enhanced antioxidant effect could not resist the occurrence of apoptosis. Furthermore, Nrf2 overexpression effectively improved the anti-oxidative levels and increased cell proliferation. At the same time, overexpression effectively restrained TUNEL staining and decreased the molecular levels of caspase-9, caspase-3, et al, but not that of caspase-8. By contrast, silencing the expression Nrf2 levels had the opposite effect. Collectively, Nrf2 alleviates PDLSCs via its effects on anti-oxidative and anti-intrinsic apoptosis by the activation of anti-oxidative enzymes.

The structure of arylpiperazine moieties as an important pharmacophore could generate wide pharmacological activities．Arylpiperazine derivatives referred in this paper possessed antitumor activity. The title compounds were crystallized by slow evaporation. 2-(4-(2-(4-Phenylpiperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione(1), 2-(4-(2-(4-(4-Bromophenyl)piperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione (2) and 2-(4-(2-(4-(4-Chlorophenyl)piperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione (3) crystallizes in the triclinic space group P-1 with two molecules in the unit cell. The unit cell parameters for 1 are a = 6.9159(14) Å, b = 9.999(2) Å, c = 16.925(3) Å, α = 88.25(3)°, β = 85.14(3) °, γ = 79.22(3) °. The unit cell parameters for 2 are a = 6.9995(14) Å, b = 9.919(2) Å, c = 17.671(4) Å, α= 97.55(3)°, β = 92.19(3) °, γ = 102.23(3) °. The unit cell parameters for 1 are a = 6.9872(14) Å, b = 9.863(2) Å, c = 17.557(4) Å, α=96.81(3)°, β = 91.89(3) °, γ = 101.74(3) °. Pi-pi interactions were observed between molecules, and compound 2 and 3 showed halogen interactions between molecules nearby, which was different from compound 1.

BACKGROUND: Manufacturing costs, along with operational performance, are among the major factors determining the selection of the propulsion system for unmanned aerial vehicles (UAVs), especially for aerial targets and cruise missiles. OBJECTIVES: In this paper, the design requirements and operating parameters of small turbofan engines for single-use and reusable UAVs are analysed to introduce alternative materials and technologies for manufacturing their compressor blades, such as sintered titanium, a new generation of aluminium and an alloy based on titanium aluminides. METHODS: To assess the influence of severe plastic deformation (SPD) on the hardening efficiency of the proposed materials, the alloys in the coarse-grained and submicrocrystalline states were studied. Changes in physical and mechanical properties of materials were taken into account. The thermodynamic analysis of the compressor was performed in a finite element analysis system (ANSYS) to determine the impact of gas pressure and temperature on the aerodynamic surfaces of compressor blades of all stages. RESULTS: Based on thermal and structural analysis, the stress and temperature maps on compressor blades and vanes were obtained, taking into account the physical and mechanical properties of advanced materials and technologies of their processing. The safety factors of the components were established based on the assessment of their stress-strength reliability. Thanks to nomograms, the possibility of using the new materials and the technologies was confirmed in view of the permissible operating temperature and safety factors of blades. CONCLUSIONS: The proposed alternative materials and production technologies for the compressor blades and vanes meet the design requirements of the turbofan at lower manufacturing costs.

There is high prevalence of hypertension and is rapidly increasing around the world, despite the intervention programme implemented, this study aimed at estimating the prevalence rate, test of association between hypertension and risk factors and model hypertension rate. Data used was obtained from the health record of Federal Medical Centre, Keffi from January 2016 – January 2019. Ordinal logistic regression model was used; Model Fitting Information, Goodness-of-Fit, Pseudo R-Square and Test of Parallel Lines are fitted to the data sets to test the accuracy and correctness of the model. The results indicated that the overall prevalence of hypertension rate is high at 36.4%, among the adult population, body mass index and gender are statistically significant, and Age is not significant in the study. Individuals that are overweight are more likely to be hypertensive compare to other weights. At age 40 – 49 years which have the highest rate of 26.5% and the odd ratio is 0.75 compared to others. One year increase in age 30 – 39, the cumulative odd of being hypertensive is 0.91 while other independent variables are held constant. The odd ratio of female being hypertensive is 0.85, therefore the females are more likely to be hypertensive with 54.4% compared to the males at 45.6% . There is no presence of multicolinearity among the variables and Logit models were formulated to calculate probabilities of the various possible outcomes.

According to some authors, the serum selenium level is strongly associated with the severity of liver diseases including liver cirrhosis. The aim of the study was to determine the relationship between the concentration of selenium and pro-inflammatory and profibrotic cytokines – interleukin-6 (IL-6) and growth differentiation factor 15 (GDF-15) in patients with alcoholic liver cirrhosis. The parameters studied were determined in serum of 99 alcoholic liver cirrhosis patients divided based on the severity of disease according to the Child-Turcotte-Pugh criteria. In patients with liver cirrhosis, the serum selenium concentration was statistically lower whereas serum IL-6 and GDF-15 concentrations were higher than those in the control group. Moreover, the concentration of selenium negatively correlated with the levels of GDF-15 and IL-6. The above results may indicate a role of selenium deficiency in the pathogenesis and progression of alcoholic liver disease.

Thrombin (factor IIa) and factor Xa (FXa) are key enzymes at the junction of the intrinsic and extrinsic coagulation pathways and are the most attractive pharmacological targets for the development of novel anticoagulants. Twenty non-amidino N²-thiophencarbonyl- and N²-tosyl anthranilamides 1-20 and six amidino N²-thiophencarbonyl- and N²-tosylanthranilamides 21-26 were synthesized and evaluated prothrombin time (PT) and activated partial thromboplastin time (aPTT) using human plasma at concentration 30 μg/mL in vitro. From these results, compounds 5, 9, and 21-23 were selected to study the further antithrombotic activity. The anticoagulant properties of 5, 9, and 21-23 significantly exhibited a concentration-dependent prolongation of in vitro PT and aPTT, in vivo bleeding time, and ex vivo clotting time. These compounds concentration-dependently inhibited the activities of thrombin and FXa and inhibited the generation of thrombin and FXa in human endothelial cells. In addition, data showed that 5, 9, and 21-23 significantly inhibited thrombin catalyzed fibrin polymerization and mouse platelet aggregation and inhibited platelet aggregation induced U46619 in vitro and ex vivo. N-(3'-Amidinophenyl)-2-((thiophen-2''-yl)carbonyl amino)benzamide (21) was most active.

This article considers the concepts of sustainability and sustainable development in relation to disaster risk reduction and climate change adaptation. We conceptualize sustainability from a social systemic perspective, that is, from a perspective that encompasses the multiple functionalities of a social system and their interrelationships in particular environmental contexts. The systems perspective is applied in our consideration and analysis of disaster risk reduction (DRR), climate change adaptation (CCA), and sustainable development (SD). Section 1 introduces briefly sustainability and sustainable development, followed by a brief presentation of the theory of complex social systems (Section 2). The theory conceptualizes interdependent subsystems, their multiple functionalities, and the agential and systemic responses to internal and external stressors on a social system. Section 3 considers disaster risk reduction (DRR) and climate change adaptation (CCA), emerging in response to one or more systemic stressors. It illustrates these with disaster risk reduction in the cases of food and chemical security regulation in the EU. CCA is illustrated by initiatives and developments on the island of Gotland, Sweden and in the Gothenburg Metropolitan area, which go beyond a limited CCA perspective, taking into account long-term sustainability issues. Section 4 discusses the limitations of DRR and CCA, not only their technical limitations but economic, socio-cultural, and political limitations, as informed from a sustainability perspective. It is argued that DRRs are only partial subsystems and must be considered and assessed in the context of a more encompassing systemic perspective. Part of the discussion is focused on the distinction between sustainable and non-sustainable DRRs and CCAs. Section 5 presents a few concluding remarks about the importance of a systemic perspective in analyzing DRR and CCA as well as other similar subsystems in terms of sustainable development.

Cellular oxidation is responsive to external and internal stimulation and is generated via signal molecules in defense mechanisms through networks of cell proliferation, differentiation, intracellular detoxification, bacterial infection, and immune reactions. Oxidative stress is not necessarily harmful per se; it depends on the balance between oxidation and antioxidation cascades, which are induced according to stimuli and can maintain oxygen homeostasis. The reactive oxygen species (ROS) that are generated during influenza virus (IV) infection have critical effects on both the virus and host cells. In this review, we outline the link between viral infection and ROS production, using IV as an example. We introduce the current state of knowledge on the molecular relationship between cellular oxidation mediated by ROS production and various effects of IV infection. We also summarize the potential anti-IV agents that act by targeting oxidative stress.

X-ray fluorescence is largely employed in the measurement of the thickness of coatings. Despite of its diffusion, the task is not straightforward because of the complex physics involved that results in high dependence on matrix effects. Thickness quantification is in practice accomplished using the Fundamental Parameters approach, adjusted with empirical measurements of standards with known composition and thickness. This approach has two major drawbacks: i) there are no standards for any possible coating and coating architecture and ii) even relying on standards, the quantification of unknown samples requires the precise knowledge of the matrix nature (e.g., in case of multilayer coatings the thickness and the composition of each underlayer). In this work, we describe a semiquantitative approach to coatings thickness measurement based on the construction of calibration curves through simulated XRF spectra built with Monte Carlo simulations. Simulations have been performed with the freeware software XMI-MSIM. We have assessed the accuracy of the methods by comparing the results with those obtained by i) XRF thickness determination with standards and ii) FIB-SEM cross-sectioning. Then we evaluated which parameters are critical in this kind of indirect thickness measurements.

A simple approach to enable water-management agencies employing free data to achieve the goal of using a single set of predictive equations for water-quality retrievals with satisfactory accuracy is proposed. Multiple regression-derived equations based on surface reflectance, band ratios, and environmental factors as predictor variables for concentrations of Total Suspended Solids (TSS), Total Nitrogen (TN), and Total Phosphorus (TP) were derived using a hybrid forward-selection method that considers Variance Inflation Factor (VIF) in the forward-selection process. Landsat TM, ETM+, and OLI/TIRS images were jointly utilized with environmental factors, such as wind speed and water surface temperature, to derive the single set of equations. The coefficients of determination of the best-fitting resultant equations varied from 0.62 to 0.79. Among all chosen predictor variables, ratio of reflectance of visible red (Band 3 for Landsat TM and ETM+, or Band 4 for Landsat OLI/TIRS) to visible blue (Band 1 for Landsat TM and ETM+, or Band 2 for Landsat OLI/TIRS) has a strong influence on the predictive power for TSS retrieval. Environmental factors including wind speed, remote sensing-derived water surface temperature, solar altitude, and time difference (in days) between the image acquisition and water sampling were found important in water-quality parameter estimation.

A gold(I) complex with a triphenylphosphine and a monodentate N,N-dimethyldithiocarbamate ligand was synthesized and characterized by Raman spectroscopy and single crystal X-ray diffraction. DFT calculations (Gaussian 09, PBE1PBE/Lanl2dz) were undertaken for a single complex in the gas-phase. The DFT-optimized structure is in good agreement with the crystal structure and the DFT-calculated Raman spectrum also is in excellent agreement with the experimental spectrum. Assignments of the Raman peaks are based on these DFT calculations. Frontier molecular orbitals were calculated and their nature is discussed.

Fragile X syndrome (FXS) is the most frequent monogenic form of autism spectrum disorder (ASD). Autistic FXS is caused by loss of the fmr1 gene product, the fragile X mental retardation protein (FMRP), triggering physiological and behavioral abnormalities. It is correlated with clock components for behavioral circadian rhythm. Mutation of this gene causes the disturbances in sleep patterns and circadian behavior commonly observed in patients with autistic FXS, accompanied by frequent dysregulation of melatonin synthesis and melatonin-dependent signaling. These changes impair vigilance, learning and memory, and are also linked to autistic behavior including the abnormal anxiety response. However, although several possible causes, symptoms, and clinical features of ASD have been investigated, the correlation between an altered circadian rhythm and autistic FXS has not been extensively studied. Recent works have highlighted the impact of melatonin on the nervous, immune, and metabolic systems. Even though utilization of melatonin for sleep disorder in ASD has been considered in clinical research, further studies should be aimed at its neuroprotective role in ASD during developmental period. In this review, we focus on the regulatory circuits involved in melatonin dysregulation and circadian system disruption in those with autistic FXS. Additionally, we discuss the neuroprotective effect of melatonin intervention. This may improve neuroplasticity and physical capability. We also review the underlying molecular mechanisms, and suggest that melatonin may be a useful novel treatment for autistic FXS, countering the adverse effects of circadian variation.

Piezoelectric properties are of significant importance to medical ultrasound, actuators, sensor, and countless other device applications. The mechanism of piezoelectric properties can be deeply understood from structure evolutions. In this paper, we report a diagram of structure evolutions of the Pb(Zn1/3Nb2/3)0.91Ti0.09O3 (PZN-9PT) single crystal with excellent piezoelectric properties among the orthorhombic, tetragonal, and cubic phases with temperature increasing from room temperature to 220 C. Through fitting the temperature dependence XRD curves with Gauss and Lorenz functions, we obtained the evolutions of the content ratio of three kinds of phases (orthorhombic, tetragonal and cubic) and the lattice parameters of the PZN-9PT system with the changes of temperature. The XRD fitting results together with Raman and dielectric spectrums show that the phase transitions of PZN-9PT are a typical continuous evolution process, very similar to the phase transition of paraffin from solid to liquid. Additionally, resonance and anti-resonance spectrum show excellent piezoelectric properties of the crystals, which probably originate from the nano twin domains, as demonstrated by the TEM images. Of particular attention is that the thickness electromechanical coupling factor kt is up to 72%.

During middle age, women are less susceptible to nonalcoholic steatohepatitis (NASH) than men. Thus, we investigated the underlying molecular mechanisms behind these sexual differences using an established rat model of NASH. Mature female and male stroke-prone spontaneously hypertensive 5/Dmcr rats were fed control or high-fat-cholesterol (HFC) diets for 2, 8, and 14 weeks. Although HFC-induced hepatic fibrosis was markedly less severe in females than in males, only minor gender differences were observed in expression levels of cytochrome P450 enzymes (CYP)7A1, CYP8B1 CYP27A1, and CYP7B1, and multidrug resistance-associated protein 3, and bile salt export pump, which are involved in fibrosis-related bile acid (BA) kinetics. However, the BA detoxification-related enzymes UDP-glucuronosyltransferase (UGT) and sulfotransferase (SULT) 2A1, and the nuclear receptors constitutive androstene receptor (CAR) and pregnane X receptor (PXR), were strongly suppressed in HFC fed males, and were only slightly changed in HFC-diet fed females. Expression levels of the farnesoid X receptor and its small heterodimer partner were similarly regulated in a gender-dependent fashion following HFC feeding. Hence, the pronounced female resistance to HFC-induced liver damage likely reflects sustained expression of the nuclear receptors CAR and PXR and the BA detoxification enzymes UGT and SULT.

The crack geometry and associated strain field around Berkovich and Vickers indents on silicon have been studied by X-ray diffraction imaging and micro-Raman spectroscopy scanning. The techniques are complementary, the Raman data coming from within a few micrometers of the indentation, whereas the X-ray image probes the strain field at a distance of typically tens of micrometers. For example, Raman data provides an explanation for the central contrast feature in the X-ray images of an indent. Strain relaxation from breakout and high temperature annealing are examined and it is demonstrated that millimeter length cracks, similar to those produced by mechanical damage from misaligned handling tools, can be generated in a controlled fashion by indentation within 75 micrometers of the bevel edge of 200mm diameter wafers.

The first FDA-approved drugs were small, chemically-manufactured and highly active molecules with possible off-target effects. After this first successful wave of small drugs, biotechnology allowed the development of protein-based medicines such as antibodies. Conventional antibodies bind a specific protein and are becoming increasingly important in the therapeutic landscape. A very prominent class of biologicals are the anti-TNF drugs that are applied in several inflammatory diseases that are characterized by dysregulated TNF levels. Marketing of TNF inhibitors revolutionized the treatment of diseases such as Crohn’s disease. However, these inhibitors also have undesired effects, some of them directly associated with the inherent nature of this drug class such as immunogenicity, whereas others are linked with their mechanism of action. Recently, researchers tried to design innovative drugs with reduced side effects aiming to make them more effective and safer. Molecules with more specificity e.g. that target one specific TNF format or receptor, or that neutralize the TNF signaling pathway in specific cells, are generated. Alternatively, TNF-directed biologicals without the typical antibody structure are manufactured. Here, we review the complications related to the use of conventional TNF inhibitors, together with the anti-TNF alternatives and the different (neurodegenerative) diseases that might benefit from selective approaches.

Infection with Severe Acute Respiratory Syndrome coronavirus 2 (SARS-CoV-2) causes Coronavirus Disease 2019 (COVID-19), which has reached pandemic proportions. A number of effective vaccines have been produced, including mRNA vaccines and viral vector vaccines, which are now being implemented on a large scale in order to control the pandemic. The mRNA vaccines are composed of the Spike S1 protein encoding mRNA, incorporated in a lipid nanoparticle, stabilized by polyethylene glycol (PEG). mRNA vaccines are novel in many respects, including cellular uptake, the intracellular routing, processing, and secretion of the viral protein. Viral vector vaccines have incorporated DNA sequences encoding the SARS-CoV-2 Spike S1 protein into (attenuated) adenoviruses. The antigen presentation routes in MHC class I and class II, in relation to induction of virus neutralizing antibodies and cytotoxic T-lymphocytes will be reviewed. In rare cases, mRNA vaccines induce unwanted immune mediated side effects. mRNA based vaccines may lead to an anaphylactic reaction. This reaction may be triggered by PEG. The intracellular routing of PEG, and potential presentation in the context of CD1 will be discussed. Adenovirus vector based vaccines have been associated with thrombocytopenic thrombosis events. The anti-platelet factor 4 antibodies found in these patients could be generated due to conformational changes of relevant epitopes presented to the immune system.

Various crystallite size estimation methods were used to analyze X-ray diffractograms of spherical cerium dioxide and donut-like titanium dioxide anatase nanoparticles aiming to evaluate their reliability and limitations. The microstructural parameters were estimated from Scherrer, Monshi, Williamson-Hall, and their variants: i) uniform deformation model, ii) uniform strain deformation model, and iii) uniform deformation energy density model, and also size-strain plot, and Halder-Wagner method. For that, and improved systematic Matlab code was developed to estimate the crystallite sizes and strain, and the linear regression analysis was used to compare all the models based on the coefficient of determination, where the Halder Wagner method gave the highest value (close to 1). Therefore, being the best candidate to fit the X-ray Diffraction data of metal-oxide nanoparticles. Advanced Rietveld was introduced for comparison purposes. Refined microstructural parameters were obtained from a nanostructured 40.5 nm Lanthanum hexaboride nanoparticles and correlated with the above estimation methods and transmission electron microscopy images. In addition, electron density modelling was also studied for final refined nanostructures, and μ-Raman spectra were recorded for each material estimating the mean crystallite size and comparing by means of a phonon confinement model.

The R&D and propagation of sustainable appropriate technology requires the provision of stable funding. Crowdfunding is a form of funding whereby small sums of investments or contributions are collected from among the general public and used to finance the development of goods or services. This method has been in use widely in arts and culture fields, and presents a useful alternative means for funding appropriate technology projects. The aim of this study is to identify the factors influencing the backers who participate in appropriate technology projects through crowdfunding platforms, analyzing the relationships between these factors, and thereby establishing the usefulness of crowdfunding as a viable new alternative. The analysis results indicate that key factors influencing user intention to crowdfund appropriate technology projects include social influence, effort expectancy, and perceived trust. In contrast to the findings of previous studies, performance expectancy was not found to have a significant effect. This reflects the fact that, compared to the crowdfunding conducted for other purposes, crowdfunding for appropriate technology is closer in nature to donations. These findings indicate that for funding to be successful, aggressive online exposure using the SNS of backers should be pursued from the early stages of funding.

Sehezar area is located in southern Tonokabon in Mazandaran province, north of Iran, near the Tarom – Hashdtjin belt. The existence of granitoid masses in the region can be important in terms of the potential of mineralization. Geochemical anomaly separation from the background is one of the important steps in mineral exploration. In the past decades, geochemical anomalies have been identified by means of various methods. Some of these separation methods include: statistical analysis methods (like univariate, bivariate, multivariate statistics), spatial statistical methods and fractal and multi-fractal methods. To identify the anomalous area, 71 stream sediment samples were collected from the area and analyzed by the ICP-MS method, and then interpreted. Initially, data were normalized and afterwards, univariate analysis (threshold limit and screening (P.N) methods) was used, in which results of the probable and definite anomaly of the threshold method were confirmed by the P.N screening method. Finally, the maps of the anomal zones were drawn. Then, bivariate analysis (Pearson correlation coefficients) and multivariate analysis on normal data were performed on SPSS software, in which factor analysis and cluster analysis were used for multivariate analysis. As a result of using the factor analysis method, six factors were identified and factor maps were drawn by the Surfer software. Also, by using cluster analysis, the variables were divided into two groups. In order for a better separation of the geochemical anomaly from the background, in addition to the threshold method, the Concentration - Area fractal method was used. Here, the fractal geometry using full-logarithmic graphs of the Concentration - Area obtained is capable of separating the stairs of different sections (background, threshold, and anomaly) with respect to the angle coefficient of the Concentration - Area plot. Then, in conclusion, results of these methods were compared and investigated, and finally, the anomalies area maps of the Au, Ag, Cu, Fe, W elements were drawn by Concentration - Area fractal and threshold methods and anomalous zones were introduced.

Fibrin rich of platelets (PRF^®) of Choukroun represents a new step in the therapeutic concept of platelet gel with a simplified processing and biochemical changes little artificial. A valid method of preparation of the PRF must effectively separate the plates by erythrocytes and concentrate without damaging or lysing the plates themselves. In this study the experimental design is to standardize the production of L-PRF in horse directing it to human production. Our hypothesis is that the L-PRF is easy to produce in the horse, without modifications of the human protocol, thus allowing a better standardization of the human protocol. A new device for the preparation and the standardization of L-PRF clots and membranes is the L-PRF Wound Box^®. The optical microscopy, most cell bodies were highlighted concentrated in the proximal portion of each membrane, the last 1/4 was observed at the center; the distal part had only residual traces of cell bodies. The L-PRF will form constantly when the phases described above are strictly adhered to. The success of the art L-PRF depends entirely on the speed of blood collection and transfer in centrifuge within a minute and by a temperature of centrifugation and compression is higher than 21°C (between 21 and 30°C). Our experiments on the horse will no doubt be able to improve our understanding on wound healing, in particularly in chronic skin lesions therapy.

Multi-criteria decision analysis (MCDA), one of the prevalent branches of operations research, aims to design mathematical and computational tools for selecting the best alternative among several choices with respect to specific criteria. In the cloud, MCDA based online brokers uses customer specified criteria to rank different service providers. However, subjected to limited domain knowledge, the customer may exclude relevant or include irrelevant criterion, which could result in suboptimal ranking of service providers. To deal with such misspecification, this research proposes a model, which uses notion of factor analysis from the domain of unsupervised machine learning. The model is evaluated using two quality-of-service (QoS) based datasets. The first dataset i.e., feedback from customers, was compiled using leading review websites such as Cloud Hosting Reviews, Best Cloud Computing Providers, and Cloud Storage Reviews and Ratings. The second dataset i.e., feedback from servers, was generated from cloud brokerage architecture that was emulated using high performance computing (HPC) cluster at University of Luxembourg (HPC @ Uni.lu). The simulation runs in a stable cloud environment i.e. when uncertainty is low, shows that online broker (equipped with the proposed model) produces optimized ranking of service providers as compared to other brokers. This is due the fact that proposed model assigns priorities to criteria objectively (using machine learning) rather than using priorities based on subjective judgments of the customer. This research will benefit potential cloud customers that view insufficient domain knowledge as a limiting factor for acquisition of web services in the cloud.

Irritable bowel syndrome (IBS) is one of the most common gastrointestinal diseases in humans. It is characterized by visceral pain and/or discomfort, hypersensitivity and abnormal motor responses along with change in gut habits. Although the etio-pathogenesis of IBS is only partially understood, a main role has been attributed to psychosocial stress of different origin. Animals models such as neonatal maternal separation, water avoidance stress and wrap restraint stress have been developed as psychosocial stressors in the attempt to reproduce the IBS symptomatology and identify the cellular mechanisms responsible for the disease. The study of these models has led to the production of drugs potentially useful for IBS treatment. This review intends to give an overview on the results obtained with the animal models; to emphasize the role of the enteric nervous system in IBS appearance and evolution and as a possible target of drug therapies.

The application of thermoelectric generators (TEG) on the nozzle of an aviation jet engine was studied by finite element TEG-simulations. Against the background of system-level requirements of the reference aircraft this work reports the resulting requirements on the TEG design with respect to applied thermoelectric (TE) element lengths and fill factors (F) within the TE modules in order to maintain a positive effect on the specific fuel consumption. Assuming a virtual optimized TE material and varying the convective heat transfer coefficients at the nozzle surfaces this work reports the achievable power output. System-level requirement on the gravimetric power density (> 100 Wkg-1) can only be met for F ≤ 21%. Extrapolating TEG coverage to the full nozzle surface, the power output reaches 1.65 kW per engine. Assessment of further potential is demonstrated by a parametric study on the fill factor, convective heat transfer coefficients, and materials performance. This study confirms a feasible design range for TEG installation on the aircraft nozzle with a positive impact on the fuel consumption. This application translates into a reduction of operational costs, allowing for an economically efficient installation of TEG in consideration of the cost-specific power output of modern thermoelectric materials.

With reference to Planck scale Hubble parameter, super luminal expansion speeds, super luminal rotation speeds and Mach’s principle, we review the current cosmological observations. With our revised assumptions, it is possible to show that, at H₀ =70 km/sec/Mpc, current cosmic temperature, age, radius, mass, mass density and rotational kinetic energy are 2.721 K, 4.41 x 1017 sec, 90 billion light years, 1.14654 x 1054 kg, 0.0482 times the current critical density and 0.6667 times the current critical energy density respectively. Based on the estimated current mass density and current rotational kinetic energy density, current cosmic dark matter density can be shown to be 0.2851 times the current critical density. Initial and current expansion speeds are 3 x 108 m/sec and 3.56 x 109 m/sec respectively. Proceeding further, we developed two interesting methods for understanding cosmic scale factor with reference to a temperature of 3000 K, redshift of 1100 and age of 3,69,000 years. Finally we would like to suggest that, with increasing cosmic age and increasing cosmic expansion speed, current universe is expanding with a speed of 11.885c. Magnitude of the future cosmic expansion speed depends on the magnitude of the future Hubble parameter. By knowing the time to time future cosmic temperatures, corresponding future Hubble parameters can be estimated and corresponding future cosmic expansion speeds can also be estimated.Proceeding further, a unified model of evolving quantum cosmology can be developed.

Most empirical work on sources of economic growth for different countries lack country-specific empirical evidence to guide policy choices in individual developing countries and previous studies of factor productivity tend to focus on the entire economy or a single sector. In this study, we use the recently developed growth accounting tools to explicitly determine the sources of economic growth at both national and sectoral levels in Zambia between 1970 and 2013. We use data from World Development Indicators and Zambia’s Central Statistical Office. On average, total factor productivity (TFP) contributes about 5.7% to economic growth. Sectoral analysis shows that agriculture contributes the least to GDP and that within each sector; factors that contribute to growth differ. Structural transformation has been slow and contributed to the observed inefficiency. We outline the implications of the observed growth and provide recommendations.

Today, non-expensive remote sensing (RS) data from different sensors and platforms can be obtained at short intervals and be used for assessing several kinds of forest characteristics at the level of plots, stands and landscapes. Methods such as composite estimation and data assimilation can be used for combining the different sources of information to obtain up-to-date and precise estimates of the characteristics of interest. In composite estimation a standard procedure is to assign weights to the different individual estimates inversely proportional to their variance. However, in case the estimates are correlated, the correlations must be considered in assigning weights or otherwise a composite estimator may be inefficient and its variance be underestimated. In this study we assessed the correlation of plot level estimates of forest characteristics from different RS datasets, between assessments using the same type of sensor as well as across different sensors. The RS data evaluated were SPOT-5 multispectral data, 3D airborne laser scanning data, and TanDEM-X interferometric radar data. Studies were made for plot level mean diameter, mean height, and growing stock volume. All data were acquired from a test site dominated by coniferous forest in southern Sweden. We found that the correlation between plot level estimates based on the same type of RS data were positive and strong, whereas the correlations between estimates using different sources of RS data were not as strong, and weaker for mean height than for mean diameter and volume. The implications of such correlations in composite estimation are demonstrated and it is discussed how correlations may affect results from data assimilation procedures.

Abstract: Comparing outcrop data to laboratory results is important to verify and validate experiments of analogue and reservoir materials especially regarding conditions for deformation experiments. This is important better understand highly complex carbonate reservoir strata and their response to changes in subsurface conditions, reducing subsurface uncertainty. This study develops methods to allow for a more straightforward comparison of outcrop data (m-scale) with experimentally created fracture arrays developed in cylindrical samples (cm-scale). The main objective is to assess usefulness of experimentally-produced fracture networks as analogues for subsurface structures, typically at the meter and above scale by developing new techniques to use the lab deformation. It analyses key characteristics of laboratory-induced fracture networks by adapting scanline methods to use with x-ray tomography (XRT) images to allow for comparison with outcrop and field data. To test and verify these new methods two low permeability carbonate samples were used for deformation testing and analysis. Applying the different scanline methods we show that they can be used to analyse lab induced fractures (mm to cm-scale) identified in XRT images for comparison with outcrop data (m-scale). In addition, these methods also allow for quantification of fracture network attributes e.g. fracture spacing, fracture apertures, orientation. This new data bridges the gap between micro-scanlines using thin sections and outcrop scanlines.

The key to simulating soil erosion is to calculate the vegetation cover (C) factor. Methods that apply remote sensing to calculate C factor at regional scale cannot directly use the C factor formula. That is because the C factor formula is obtained by experiment, and needs the coverage ratio data of croplands, woodlands and grasslands at standard plot scale. In this paper, we present a C factor conversion method from a standard plot to a km-sized grid based on large sample theory and multi-scale remote sensing. Results show that: 1) Compared with the existing C factor formula, our method is based on the coverage ratio of croplands, woodlands and grasslands on a km-sized grid, takes the C factor formula obtained from the standard plot experiment and applies it to regional scale. This method improves the applicability of the C factor formula, and can satisfy the need to simulate soil erosion in large areas. 2) The vegetation coverage obtained by remote sensing interpretation is significantly consistent (paired samples t-test, t = −0.03, df = 0.12, 2-tail significance p < 0.05) and significantly correlated with the measured vegetation coverage. 3) The C factor of the study area is smaller in the middle, southern and northern regions, and larger in the eastern and western regions. The main reason for that is the distribution of woodlands, the Hunshandake and Horqin sandy lands and the valleys affected by human activities. 4) The method presented in this paper is more meticulous than the C factor method based on the vegetation index, improves the applicability of the C factor formula, and can be used to simulate soil erosion on large scale and provide strong support for regional soil and water conservation planning.

To make low-cost catalytic materials that mimic the activity of tyrosinase enzymes (Catechol oxidase) is an exciting challenge of biochemical technology. Herein, we report the synthesis of a series of acylhydrazone-pyrazoles based biomolecule materials (L1-L7) with superior catecholase activity. These biomolecules were synthesized by a one pot chemical condensation between 5-methyl-1H-pyrazole-3-carbohydrazide and benzaldehyde derivatives. The X-ray single crystal diffraction (XRD) for two ligands L1 and L2 have been studied and the molecular structures were optimized and confirmed using the density functional theory (DFT/B3LYP) method. Copper (II) complexes of the biomolecules (L1-L7), generated in-situ, and were studied for their catalytic activities towards the oxidation reaction of catechol to ortho-quinone according to two parameters: the nature of the ligand and the nature of counter anion. The L7-CuSO4 was found to have an excellent catalytic activity (105.42 μmol·L−1·min−1) among the catalysts recently reported in the existing literature.

Mungbean [Vigna radiata (L.) Wilczek] in Australia has been transformed from a niche opportunistic crop into a major summer cropping option for dryland growers in the summer-dominant rainfall regions of Queensland and New South Wales. This transformation followed stepwise genetic improvements in both grain yields and disease resistance. For example, more recent cultivars such as ‘Crystal’, ‘Satin II’ and ‘Jade-AU‘ have provided up to a 20% yield advantage over initial introductions. Improved agronomic management to enable mechanised management and cultivation in narrow (<50 cm) rows has further promised to increase yields. Nevertheless, average yields achieved by growers for their mungbean crops remain less than 1 t/ha, and are much more variable than other broad acre crops. Further increases in yield and crop resilience in mungbean are vital. In this review, opportunities to improve mungbean have been analysed at four key levels including phenology, leaf area development, dry matter accumulation and its partitioning into grain yield. Improving the prediction of phenology in mungbean may provide further scope for genetic improvements that better match crop duration to the characteristics of target environments. There is also scope to improve grain yields by increasing dry matter production through the development of more efficient leaf canopies. This may introduce additional production risks as dry matter production depends on the amount of available water, which varies considerably within and across growing regions in Australia. Improving crop yields by exploiting photo-thermal sensitivities to increase dry matter is likely a less risky strategy for these variable environments. Improved characterisation of growing environments using modelling approaches could also better define and identify the risks of major abiotic constraints. This would assist in optimising breeding and management strategies to increase grain yield and crop resilience in mungbean for the benefit of growers and industry.

The COVID-19 pandemic situation has created even more difficulties in the quick identification and screening of the COVID-19 patients for the medical specialists. Therefore, a significant study is necessary for detecting COVID-19 cases using an automated diagnosis method, which can aid in controlling the spreading of the virus. In this paper, the study suggests a Deep Convolutional Neural Network-based multi-classification approach (COV-MCNet) using eight different pre-trained architectures such as VGG16, VGG19, ResNet50V2, DenseNet201, InceptionV3, MobileNet, InceptionResNetV2, Xception which are trained and tested on the X-ray images of COVID-19, Normal, Viral Pneumonia, and Bacterial Pneumonia. The results from 3-class (Normal vs. COVID-19 vs. Viral Pneumonia) showed that only the ResNet50V2 model provides the highest classification performance (accuracy: 95.83%, precision: 96.12%, recall: 96.11%, F1-score: 96.11%, specificity: 97.84%) compared to rest of the models. The results from 4-class (Normal vs. COVID-19 vs. Viral Pneumonia vs. Bacterial Pneumonia) demonstrated that the pre-trained model DenseNet201 provides the highest classification performance (accuracy: 92.54%, precision: 93.05%, recall: 92.81%, F1-score: 92.83%, specificity: 97.47%). Notably, the ResNet50V2 (3-class) and DenseNet201 (4-class) models in the proposed COV-MCNet framework showed higher accuracy compared to the rest six models. This indicates that the designed system can produce promising results to detect the COVID-19 cases on the availability of more data. The proposed multi-classification network (COV-MCNet) significantly speeds up the existing radiology-based method, which will be helpful to the medical community and clinical specialists for early diagnosis of the COVID-19 cases during this pandemic.

A metastable β-Ti alloy, Ti–10V–3Fe–3Al (wt.%), was subjected to thermos-mechanical processing including the compression test at 725°C, which is below the β transus temperature (780°C), and at strain rate of 10-3s-1. The presence of phases was determined using transmission electron microscopy and X-ray diffraction. Although the dynamic recovery took place together with slip, both deformation-induced α˝ martensite and ω were detected as other operating mechanisms for the first time in metastable-β Ti alloys deformed in α+β region. The volume fraction of stress-induced α˝ was higher than that of the same alloy deformed at room temperature due to higher strain applied. Stress-induced twinning was not operational, which could be related to the priority of slip mechanism at high temperature resulted from thermally-assisted nucleation and lateral migration of kink-pairs.

In laser joining of copper (Cu) and aluminum (Al) sheets, the Al sheet is widely chosen as the top surface for laser irradiation because of increased absorption of laser beam and lower melting temperature of Al in contrast to Cu. This research focus on welding from Cu side to Al sheet. The main objective of irradiating the laser beam from the copper side (Cu on top) is to exploit higher solubility of Al in Cu. A significantly lower laser power can be used with 515 nm laser in comparison to 1030 nm. In addition to low laser power, a stable welding is obtained with 515 nm. Because of this advantage, 515 nm is selected for the current research. By fusion of Cu and Al the two sheet metals are welded, with presence of beneficial Cu solid solution phase and Al+Al2Cu in the joint with the brittle phases intermixed between the ductile phase. Therefore the mixed composition strengthens the joint. However excessive mixing leads to formation of more detrimental phases and less ductile phases. Therefore optimum mixing must be maintained. Energy dispersive X-ray spectroscopy (EDS) analysis indicate that large amount of beneficial Cu solid solution and Al rich phases is formed in the strong joint. From the tensile shear test for a strong joint, fracture is obtained on the heat-affected zone (HAZ) of Al. Therefore the key for welding from copper side is to have optimum melt with beneficial phases like Cu and Al+ Al2Cu and the detrimental phases intermixed between the ductile phases

The formation of solid solution series Cs_1-xM_xGaQ₂-mC64 (M = K, Rb; Q = S, Se; x = 0–1) was studied by X-ray diffraction and spectroscopic methods, revealing a complete miscibility of CsGaQ₂-mC64 with RbGaQ₂ and KGaSe₂, and a large miscibility gap with KGaS₂. All solid solution members exhibit similar Raman spectra, indicating the covalent Ga-Q bonding character. The similar optical band gaps likewise further contribute to this conclusion. Up to a degree of substitution, these solid solutions undergo a phase transition similar to CsGaQ₂-mC64. The influence of the substitution parameter x on phase transition process was investigated in situ using high-temperature X-ray powder diffraction experiments. Phase-pure solid solutions of the high-temperature polymorphs Cs_1-xM_xGaQ₂-mC16 were obtained up to x_max(K) = 0.1 and x_max(Rb) = 0.3. The crystal structures of these new CsGaQ₂-mC16 analogous high-temperature phases were refined from synchrotron diffraction data by Rietveld-refinement.

We proposed a so-called Beta Kumaraswamy Burr Type X distribution which gives the extension of the Kumaraswamy-G class of family distribution. Some properties of this proposed model were provided, like: the expansion of densities and quantile function. We considered the Bayes and maximum likelihood methods to estimate the parameters and also simulate the model parameters to validate the methods based on different set of true values. Some real data sets were employed to show the usefulness and flexibility of the model which serves as generalization to many sub-models in the field of engineering, medical, survival and reliability analysis.

Nine 2-(1,2-benzothiazol-3-yl)-N-(4-oxo-2-phenyl-1,3-thiazolidin-3-yl) propanamides were designed and synthesized, combining benzisothiazole and 4-thiazolidinone in one frame. The aim of the study was to verify their effectiveness to contrast the inflammatory/oxidative process in which free oxygen and nitrite (ROS and RNS) radicals, advanced glycation products (AGEs), inflammatory cytokines and matrix metalloproteinases (MMPs) are involved. Docking studies of all the compounds were performed in order to explore their binding mode at the MMP-9 protein. An appreciable anti-inflammatory/wound healing effects of the tested compounds was highlighted. Derivative 23, bearing a 4-carboxyphenyl substituent at C2 of the 4-thiazolidinone ring, exhibited the highest activity, being able to inhibit MMP-9 at nanomolar level (IC₅₀ = 40 nM).

There are potentially promising mitigation activities for epidemic and pandemic scenarios that are not currently the subject of significant research effort. Large epidemics and pandemics pose risks that are important to mitigate, even if the likelihood of the events is low and uncertain. While some efforts are the subject of extensive funding and consideration, other approaches are neglected. Here, we consider such neglected interventions which could significantly reduce the impact of such an epidemic or large-scale pandemic. These are identified via a narrative literature review of extant literature reviews and overviews of mitigations in epidemic and pandemic situations, followed by consideration of the economic value of information of further study of heretofore neglected interventions and approaches.Based on that analysis, we considered several classes of mitigations, and conducted more exploratory reviews of each. Those discussed include mitigations for (1) reducing transmission, such as personal protective equipment and encouraging improved hygiene, (2) reducing exposure by changing norms and targeted changes for high-risk or critical professions and activities, (3) reducing impact for those infected, and (4) increasing large scale resilience using disaster and infrastructure continuity planning.Some proposed mitigations are found to be of low marginal value. Other mitigations are likely to be valuable, but the concepts or applications are underdeveloped. In those cases, further research, resources, or preparation are valuable for mitigating both routine and extreme disease outbreak events. Still more areas of research are identified as having uncertain value based on specific but resolvable uncertainties. In both of the latter cases, there is no guarantee that mitigations identified as worthy of further consideration will be valuable, but the argument for further research is clear.

Liver related diseases are the 3rd leading causes (9.3%) of mortality in type 2 diabetes mellitus (T2DM) in Japan. T2DM is closely associated with nonalcoholic fatty liver disease (NAFLD) which is the most prevalent chronic liver disease worldwide. Nonalcoholic steatohepatitis (NASH), a severe form of NAFLD, can lead to hepatocellular carcinoma (HCC) and hepatic failure. There are no established pharmacotherapies for NASH patients with T2DM. Though vitamin E is established as a 1st line agent in NASH without T2DM, its efficacy was recently denied in NASH with T2DM. The effects of pioglitazone on NASH histology with T2DM have extensively been established, but several concerns exist such as body weight gain, fluid retention, cancer incidence, and bone fracture. Glucagon-like peptide 1 (GLP-1) receptor agonists and sodium/glucose cotransporter 2 (SGLT2) inhibitors are expected to ameliorate NASH　(LEAN study, LEAD trial, and E-LIFT study). Among a variety of SGLT2 inhibitors, dapagliflozin have already entered phase 3 trials (DEAN study). A key clinical question is what kinds of anti-diabetic drugs are the most appropriate for the treatment of NASH to prevent progression of hepatic fibrosis resulting in HCC/liver-related mortality without increasing risk at cardiovascular or renal events. The combination therapies such as glucagon receptor agonist/GLP-1 or gastrointestinal peptide /GLP-1 will be under development. This review focuses on antidiabetic agents and future perspectives on the view of the treatment of NAFLD with T2DM.

With the unceasing advancement in wide-bandgap (WBG) semiconductor technology, the minimal reverse-recovery charge Qrr and other more powerful natures of WBG transistors enable totem-pole bridgeless PFC to become a dominant solution for energy storage systems (ESS). This paper focuses on design and implementation of a control structure for a totem-pole boost PFC with newfangled enhancement-mode Gallium Nitride (eGaN) FETs, not only to simplify the control implementation, but also to achieve high power quality and efficiency. The converter is designed to convert a 90-264-VAC input to a 385-VDC output for a 2.6-kW output power. Lastly, to validate the methodology, an experimental prototype is characterized and fabricated. The uttermost efficiency at 230 VAC attains 99.14%. The lowest total harmonic distortion in the current (ITHD) at high line condition (230 V) reaches 1.52% while the power factor gains 0.9985.

In this paper new upper limits on the parameters of the Continuous Spontaneous Localization (CSL) collapse model are extracted. To this end the X-ray emission data collected by the IGEX collaboration are analyzed and compared with the spectrum of the spontaneous photon emission process predicted by collapse models. This study allows to obtain the most stringent limits within a relevant range of the CSL model parameters, with respect to any other method. The collapse rate $\lambda$ and the correlation length $r_C$ are mapped, thus allowing to exclude a broad range of the parameter space.

Proposed in 1889 by Svante Arrhenius, the Arrhenius equation is an important result in physical chemistry which aims to find the relationship between temperature and reaction rates. It is also an essential equation for analytic chemistry which helps to determine the energy barrier for a given reaction. In this article, we will go through a detailed derivation of the exponential factor in the Arrhenius Equation based on the Boltzmann distribution of particle energy probability. Then, we will attempt to model the pre-exponential factor in accordance with the principles of collision theory for bi-molecular reaction with gaseous reactants. Understanding the basic principles of chemical reaction provides valuable tools to analyze complex reaction mechanisms in the perspective of optimizing existing industrial processes.

Legionella pneumophila RpoS (LpRpoS) is an alternative sigma factor of RNA polymerase (RNAP) essential for virulence and stress resistance. To investigate the mechanism of RpoS in the intracellular pathogen L. pneumophila, we determined the high-resolution crystal structure of the LpRpoS (residues 95-194) containing a partial region 1.2 and region 2. The structure of LpRpoS (residues 95-194) reveals that the conserved residues are critical for promoter melting, DNA and core RNAP binding. The differences in regulatory factor binding site between Escherichia coli RpoS and LpRpoS suggest that LpRpoS may employ a distinct mechanism to recruit alternative regulatory factors controlling transcription initiation.

Purpose of this article is to project from the point of view of the scientific data concerning PAF and as a new approach by involving PAF, in order to contribute to clarification and proposal a possible mechanism of action of the coronavirus SARS-CoV-2 and to give a possible explanation for its observed side effects-complications of Covid-19 disease. The article is not intended to suggest any specific drugs, but clarifying the mechanism is the first step in illuminating the direction of prescribing the targets of medication that may be appropriate for the prevention, treatment, and cure of Covid-19 disease. More specifically, the purpose of this article is to provide unequivocal evidence indicating that: 1 It would not be unexpected for PAFR to participate in the entry of coronavirus SARS-CoV-2 into the cell. 2 There is interdependence and relationship of the receptors ACER and PAFR, which means the involvement of PAF in the processes related to coronavirus SARS-CoV-2 as well as to its effects exercised by the coronavirus SARS-CoV-2. 3 The receptors ACER, PAFR and TLRs are also involved in inflammation as well as in virus binding to stabilize and enter into the cell, and so they are "communicating vessels" with PAF being " a missing link" 4 Consequently there is a correlations of COVID-19 disease manifestations and biological characteristics with those caused by PAF, which shows the involvement of PAF in COVID-19 disease.

The aim of this study was to develop a basic model to predict enteric methane emission from dairy cows and to update operational calculations for the national inventory in Norway. Basic models were developed using a database with 63 treatment means from 19 studies. The database included records for enteric CH4 production (MJ/day), dry matter intake (DMI), and dietary nutrient composition. The basic models were evaluated against an external database (n=36, from ten studies) along with other extant models. When evaluated by low root mean square prediction errors and high concordance correlation coefficients, the developed basic models that included DMI, dietary concentrations of fatty acids and neutral detergent fiber performed slightly better in predicting CH4 emissions than extant models. In order to propose country-specific values for the CH4 conversion factor Ym (% of gross energy intake partitioned into CH4) and thus to carry out the national inventory for Norway, the existing operational model was updated for the prediction of Ym over a wide range of feeding situations using energy corrected milk and dietary concentrate share as predictor variables. Input values of Ym were updated based on the results from the basic models. The predicted Ym ranged from 6.22 to 6.72%. In conclusion, the prediction of CH4 production from dairy cows was improved with the help of newly published data, which enabled an update of the operational model for calculating the national inventory of CH4 in Norway.

Populations with essential hypertension have a high risk of nonalcoholic steatohepatitis (NASH). In this study, we investigated the mechanism that underlies the progression of hypertension-associated NASH by comparing differences in the development of high fat and cholesterol (HFC) diet-induced NASH among three strains of rats, i.e., two hypertensive strains comprising spontaneously hypertensive rats and the stroke-prone spontaneously hypertensive 5/Dmcr, and the original Wistar Kyoto rats as the normotensive control. We investigated histopathological changes and molecular signals related to inflammation in the liver after feeding with the HFC diet for 8 weeks. The diet induced severe lobular inflammation and fibrosis in the livers of the hypertensive rats, whereas it only caused mild steatohepatitis in the normotensive rats. Increased activation of proinflammatory signaling (transforming growth factor-β1/mitogen-activated protein kinases pathway) was observed in the hypertensive strains fed with the HFC diet. In addition, the HFC diet suppressed the nuclear factor erythroid 2-related factor 2 pathway in the hypertensive rats and led to lower increases in the hepatic expression of heme oxygenase-1, which has anti-oxidative and anti-inflammatory activities. In conclusion, these signaling pathways might play crucial roles in the development of hypertension-associated NASH.

For shear-critical structural elements where the use of stirrups is not desirable, such as slabs or beams with reinforcement congestion, steel fibers can be used as shear reinforcement. The contribution of the steel fibers to the shear capacity lies in the action of the steel fibers bridging the shear crack, which increases the shear capacity and prevents a brittle failure mode. This study evaluates the effect of the amount of fibers in a concrete mix on the shear capacity of steel fiber reinforced concrete beams with mild steel tension reinforcement and without stirrups. For this purpose, twelve beams were tested. Five different fiber volume fractions were studied: 0.0%, 0.3%, 0.6%, 0.9%, and 1.2%. For each different steel fiber concrete mix, the concrete compressive strength was determined on cylinders and the tensile strength was determined in a flexural test on beam specimens. Additionally, the influence of fibers on the shear capacity is analyzed based on results reported in the literature, as well as based on the expressions derived for estimating the shear capacity of steel fiber reinforced concrete beams. The outcome of these experiments is that a fiber percentage of 1.2% or fiber factor of 0.96 can be used to replace minimum stirrups according to ACI 318-14 and a 0.6% fiber volume fraction or fiber factor of 0.48 to replace minimum stirrups according to Eurocode 2. A fiber percentage of 1.2% or fiber factor of 0.96 was observed to change the failure mode from shear failure to flexural failure. The results of this presented study support the inclusion of provisions for steel fiber reinforced concrete in building codes and provides recommendations for inclusion in ACI 318-14 and Eurocode 2, so that a wider adoption of steel fiber reinforced concrete can be achieved in the construction industry.

This paper studies the influence mechanism of industrial agglomeration and foreign direct investment (FDI) on green total factor productivity (GTFP). We use the SBM Directional Distance Function to measure the GTFP of Chongqing's manufacturing industry from 1999 to 2015. The results show that the level of GTFP in Chongqing's manufacturing industry is relatively low, which is contrary to the current green development mode. By clarifying the conduction path of industrial agglomeration and FDI on GTFP, we use the panel Tobit model to study the effect of industrial agglomeration and FDI on GTFP. The main findings are: the higher the level of industrial agglomeration, the more beneficial it is to increase GTFP. FDI has an inhibitory effect on GTFP. The spillover effect of FDI on GTFP is not significant. At the same time, FDI counteracts the role of industrial agglomeration in promoting GTFP. The findings in a present study indicate that, according to Chongqing's experience, the "pollution haven" is established. Therefore, relying solely on foreign technology to promote the development of the manufacturing industry has many drawbacks clearly. Only by improving the ability of independent innovation is the reliable way to enhance GTFP effectively.

We report on the fabrication and electrical characteristics of zinc-oxide (ZnO) based metal-insulator-semiconductor (MIS) type Schottky barrier diodes (SBHs). ZnO thin layer on the p-type silicon substrate was fabricated by atomic layer deposition (ALD). The structure and surface properties of the thin film were characterized by X-ray diffraction (XRD), atomic force microscope (AFM) and secondary ion mass spectrometer (SIMS). The current-voltage (I-V) characteristics of Al/ALD-grown ZnO/p-Si diodes were measured under dark at room temperature. The electrical parameters such as ideality factor (n), series resistance (R_s) and barrier height (ϕ_b) of the diodes were analyzed using standard thermionic emission (TE) theory, Norde and Cheung method. The barrier height value obtained from I-V and Cheung method was found to be 0.73 eV and 0.76 eV, respectively. The interface state density (Dit) of the diodes was determined from the I-V characteristics. The nonideal behavior of measured parameters suggested the presence of interface states. The obtained results showed that the prepared diode can be used for NIR Schottky photodetector applications.

Herein, we present preparation of solid polymer electrolyte (SPE) comprising of PEO, NaPF₆ and varying fraction of Succinonitrile (SN) by standard solution cast technique. The morphological features and structural properties were studied by the FESEM, XRD, respectively. FTIR was performed to study the interactions between polymer host, salt, and SN. Impedance spectroscopy, Transference number measurements, LSV and CV were used to examine the electrochemical properties. The complex permittivity/conductivity & modulus were studied to understand the dielectric properties by evaluating the dielectric strength, relaxation time, hopping frequency and dc conductivity. Based on the experimental results an interaction mechanism is presented.

The considerable biological and medicinal activities of pyridazines has stimulated considerable research on efficient syntheses of these derivatives. In the last decade, microwave irradiation has generally been used for the energy source. As demonstrated in recent studies, pressure reactor “Q-tubes” may be used to accelerate several of these reactions in a more optimal and safer manner (compared to microwaves). In these studies there has been postulated a pathway for the formation of pyridazino[5,4,3-de][1,6]naphthyridine derivatives . In this paper we consider this pathway, and an alternate pathway, for several reactions. Contrary to the suggestion in these studies the pathway in which initial dimerization of malononitrile was postulated could be excluded based on chemical evidence. The reactions performed were the reaction of arylhydrazonals 1a,b with benzylidinemalononitrile which afforded in Q-tube the 3-acyl-4-aryl-1-phenyl-6-amino-1,4-dihydropyridazines, and the reaction of arylhydrazonals 1a,b, malononitrile 9 and aromatic aldehydes 10a-g in Q-tubes which afforded the tricyclic systems 12a-n whose structure could be established by X-ray crystal structure determination. In conclusion, we have added to the work of the recent studies by excluding a reaction pathway for one of their reaction products.

The paper demonstrates the analysis of Corona Virus Disease based on a CNN probabilistic model. It involves a technique for classification and prediction by recognizing typical and diagnostically most important CT images features relating to Corona Virus. The main contributions of the research include predicting the probability of recurrences in no recurrence (first time detection) cases at applying our proposed Convolution neural network structure. The Study is validated on 2002 chest X-ray images with 60 confirmed positive covid19 cases and (650 bacterial – 412 viral -880 normal) x-ray images. The proposed CNN compared with traditional classifiers with proposed CHFS feature extraction model. The experimental study has done with real data demonstrates the feasibility and potential of the proposed approach for the said cause. The result of proposed CNN structure has been successfully done to achieve 98.20% accuracy of covid19 potential cases with comparable of traditional classifiers.

Since coffee has been shown to influence positively the metabolism of subjects with metabolic syndrome (MetS), we aimed to evaluate the short- and long-term effects of a coffee-based supplement on different features of diet-induced MetS. 24 Sprague Dawley rats were divided into control or nutraceuticals groups to receive a high-fat/high fructose diet with or without a mixture of caffeic acid (30 mg/day), trigonelline (20 mg/day), and cafestol (1 mg/day) for 12 weeks. An additional 11 rats were assigned to an acute crossover study. In the chronic experiment, nutraceuticals did not alter body weight or glycemic control but improved fed hyperinsulinemia and HOMA-IR, and plasma adiponectin levels. The impact of nutraceuticals on post-prandial glycemia tended to be more pronounced after acute administration than at the end of the chronic study. Circulating and intrahepatocellular alanine transaminase activity, assessed by hyperpolarized-¹³C NMR spectroscopy, were reduced by coffee nutraceuticals at endpoint. There was also a tendency towards lower liver triglyceride content and histological steatosis score in the intervention group. In conclusion, a mixture of coffee nutraceuticals improved insulin sensitivity and exhibited hepatoprotective effects in a rat model of MetS. Higher dosages with or without caffeine deserve to be studied in the future.

A novel hybrid cobalt phosphite, (H2DAB)[Co(H2PO3)4]·2H2O, has been synthesized by using slow evaporation method, in the presence of cobalt nitrate, phosphorous acid and 1,4- dia-minobutane (DAB= 1,4- diaminobutane) as a structure-directing agent. Single crystal X-ray diffraction analysis showed that the compound crystallizes in the P-1(n.2) triclinic space group, with the following unit cell parameters (Å, °) a = 5.4814 (3), b = 7.5515 (4), c = 10.8548 (6), α = 88.001 (4), β = 88.707 (5), γ = 85.126 (5), and V= 447.33 (4) Å3. The crystal structure was built up from cor-ner-sharing [CoO6] octahedra, forming chains parallel to [001], which are interconnected by H2PO3 pseudo-tetrahedral units. The deprotonated cations, residing between the parallel chains, interacted with the inorganic moiety via hydrogen bonds leading thus to the formation of the 3D crystal structure. The Fourier transform infrared spectrum showed characteristic bands corresponding to the phosphite group and the organic amine. The thermal behavior of the compound consisted mainly of the loss of its organic moiety and the water molecules. The biological tests exhibited significant activity against Candida albicans and Escherichia coli strains in all used concentrations, while less inhibitory activity was pronounced against Staphylococcus epidermidis and Saccharomyces cerevisiae, and in the case of multi-cellular organisms, no activity against the nematode model Steinernema feltiae was detected.

The concept of Design Fatigue Factors (DFFs) was introduced for providing desired level of safety in structural fatigue design, often associated with damage calculated from S-N curves. Calculation of fatigue damage from S-N curves can be affected by multiple factors, e.g. types of weld class, corrosion condition, loading conditions, stress concentration on different geometries etc. Each of them can be subject to different level of uncertainties. This study intends to recalibrate the DFFs from a detailed reliability analysis by investigating the probabilistic models derived from the database of S-N curves that has been most frequently used in offshore wind industry. The results of such study indicate that the DFFs can be reduced substantially for the corrosive environmental fatigue models from current standards to the same level of target reliability.

The rapid growth rate of the elderly population is a serious current issue in most countries, affecting them economically through needed medical treatment and healthcare planning. The priority concern is how to reduce the number of elderly people requiring long-term healthcare and raise the number who are able to live independently. This study executed a behavior assessment of elderly person’s self-reported use of electric scooters and analyzed their degree of acceptance of these assisted living tools, partly through a related factor analysis of our survey instrument. We used this questionnaire survey as our research method, applying SPSS22 software for factor analysis that revealed five survey facets.

Cold gas-dynamic spray (cold spray) is an evolving coating deposition and restoration technology in which particles are deposited above the sonic speed. This paper presents the non-destructive three-dimensional characterization of cold sprayed stainless steel coating. The visualization of coating morphology and volumetric porosity, and the analyses of porosity size and spatial distributions confirmed that dense stainless steel coating with non-connected, micron-sized gradient porosity is successfully produced by cold spray. The suitability of X-ray tomography for characterizing cold sprayed coatings is assessed.

This paper presents a comparison between rain gauges, C-band and X-band radar data over an instrumented and regulated catchment of the Paris region, as well as their respective hydrological impacts with the help of flow observations and a semi-distributed hydrological model. Both radars confirm the high spatial variability of the rainfall down to their space resolution (respectively one kilometer and 250 m) and therefore underscore limitations of semi-distributed simulations. The use of the polarimetric capacity of the Météo-France C-band radar was limited to corrections of the horizontal reflectivity and its rainfall estimates are adjusted with the help of a rain gauge network. On the contrary, neither calibration was performed for the polarimetric X-band radar of the Ecole des Ponts ParisTech (below called ENPC X-band radar), nor any optimization of its scans. In spite of that and the non-negligible fact that the catchment was much closer to the C-band radar than to the X-band radar (20 km vs. 40 km), the latter seems to perform at least as well as the former, but with a higher scale resolution. This characteristic was best highlighted with the help of a multifractal analysis of the respective radar data, which also shows that the X-band radar was able to pick up a few extremes that were smoothed out by the C-band radar.

Biomimicry in additive manufacturing often refers to topology optimization and the use of lattice structures, due to the organic shape of the topology-optimized designs, and the lattices often looking similar to many light-weight structures found in nature such as trabecular bone, wood, sponges, coral, to name a few. Real biomimetic design however involves the use of design principles taken in some way from natural systems. In this work we use a methodology whereby high resolution 3D analysis of a natural material with desirable properties is “reverse-engineered” and the design tested for the purpose. This allows more accurate replication of the desired properties, and adaption of the design parameters to the material used for production (which usually differs from the biological material). One such example is the impact-protective natural design of the glyptodont body armour. In this paper we report on the production of body armour models in metal (Ti4Al4V) and analyze the resulting mechanical properties, assessing their potential for impact protective applications. This is the first biomimetic study using metal additive manufacturing to date.

In Ghana, about 73% of households rely on solid fuels for cooking. Over 13,000 annual deaths are attributed to exposure to indoor air pollution from inefficient combustion. In this study, assessment of thermal efficiency, emissions and total global warming impact of three cookstoves commonly used in Ghana was completed using IWA water boiling test (WBT) protocol. Statistical averages of three replicate tests for each cookstove were computed. Thermal efficiency results were: wood-burning cookstove 12.2% (Tier 0), traditional charcoal cookstove 23.3% (Tier 1-2) and improved charcoal cookstove 30% (Tier 2-3). The wood-burning cookstove emitted more CO, CO2 and PM2.5 than charcoal cookstove (coalpot) and improved cookstove. Emission factor for PM2.5 and emission rate for the wood-burning cookstove (Tier 0) were over four times higher than the traditional charcoal cookstove (Tier 3) and improved cookstove (Tier 2). On the basis of WBT, annual global warming impact potential for emissions are estimated at 4 tonnes of CO2e for the wood-burning cookstove, 1.5 tonnes of CO2e for charcoal cookstove (coalpot) and 1 tonne of CO2e for improved cookstove. We conclude that there is the need for awareness, policy and incentives to enable end-users switch to improved cookstoves for increased efficiency, reduced emissions/global warming impact.

Abstract Due to the relatively low efficiency of thermoelectric (TE) generators, they have mostly been used in niche applications where the unique properties of TE generators outweigh their lack of efficiency, or conditions where it is more reasonable to base the optimal design on maximum generated power rather than maximum efficiency. The aim of this work is to investigate how the different fundamental transport properties (Seebeck coefficient, thermal conductivity and electrical resistivity) in materials with equal figure of merit (ZT) impact TE module design and maximum power output. Further, we discuss and review the strategies to enhance material properties and the latest studies on the TE module performance. It is shown, that by increasing the power factor by a factor of 15 and decreasing the thermal conductivity by 13.33 in order to maintain ZT=1, power output is increased by 45%. This effect is stronger in lower module fill factor and thermal resistance of the heat source and heat sink.

The objective of this research is to develop an experimental-theoretical analysis about the influence of the cooling medium and the geometry of the welding bead profile in fatigue life and associated parameters with structural integrity of welded joints. A welded joint with cruciform geometry is considered using SMAW, plates in structural steel ASTM A36 HR of 8 mm of thickness and E6013 electrode input. A three-dimensional computational model of the cruciform joint was created using the finite element method. For this model, the surface undulation of the cord and differentiation in the mechanical properties of the fusion zone were considered, the heat-affected zone (HAZ) and base material, respectively. In addition, an initial residual stress field which was established experimentally was considered. The results were a set of analytical expressions for the weld magnification factor Mk. It was found that values for the latter decrease markedly in function of the intensity of the cooling medium used in the post welding cooling phase, mainly due to the effect of the residual compressive stresses. The obtained models of behavior of the weld magnification factor are compared with the results from other researchers with some small differences, mainly due to the inclusion of the cooling effect of the post weld and the variation of the leg of the weld bead. The obtained analytical equations in the present research for Mk can be used in management models of life and structural integrity for this type of welded joint.