In this paper, four lithological parameters, i.e. thermal conductivity, particle size, porosity and saturation, are investigated by combining experimental observations with numerical simulations to study the influence laws and mechanisms of action on the combustion process of methane hydrate sediments. The variation of combustion characteristics parameters such as flame height, effective combustion ratio and dimensionless discharge water mass with the lithological parameters are studied. In addition, the combustion mechanism of lithologic parameters on methane hydrate deposits is revealed. Combining the experimental results and simulation calculations, to optimize the combustion of methane hydrate sediments, it is recommended to use methane hydrate sediment samples with high saturation and low thermal conductivity, while the oxidant concentration and porosity of methane hydrate sediment samples should be increased.

Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

To estimate The potential inventory of natural gas hydrates in the Levant Basin we correlated the gas hydrate stability zone (GHSZ), modeled with locally estimated thermodynamic parameters, with seismic indicators of gas. Compilation of oceanographic measurements define the deep-water temperature and salinity to 13.8°C and 38.8‰ respectively, predicting the top GHSZ at a water depth of 1250±5 m. Assuming beneath the seafloor a hydrostatic pore-pressure, the water body salinity, and geothermal gradients ranging between 20 to 28.5°C/km, yields a useful first-order base-GHSZ approximation. Our model predicts that the entire northwestern half of the Levant Basin lies within the GHSZ, with a median thickness of ~150 m. High amplitude seismic reflectivity (HASR) imaged on an extensive 3D seismic dataset, consistently correlates with verified active seafloor gas seepage and is pervasively distributed across the deep-sea fan of the Nile within the Levant. Two main trends observed for the distribution of HASR are suggested to represent: (1) shallow gas and possibly hydrates, within buried channel-lobe systems 25 to 100 m beneath the seafloor; and (2) a regionally discontinuous bottom simulating reflection (BSR) broadly matching the modeled base GHSZ. We therefore estimate the potential methane hydrates reserve within the Levant Basin at ~4 Tcf.

Large amounts of gas hydrate are present in marine sediments offshore Taitao Peninsula, near the Chile Triple Junction. Here, marine sediments on the forearc contain carbon that is converted to methane in a zone of very high heat flow and intense rock deformation above the downgoing oceanic spreading ridge separating the Nazca and Antarctic plates. This regime enables vigorous fluid migration. Here we present an analysis of the spatial distribution, concentration, estimate of gas phases (gas hydrate and free gas) and geothermal gradients in the accretionary prism and forearc sediments offshore Taitao (45.5° - 47° S). Velocity analysis of Seismic Profile RC2901-751 indicates gas hydrate concentration values <10% of the total rock volume, and extremely high geothermal gradients (<190 °Ckm^-1). Gas hydrates are located in shallow sediments (90-280 meters below the seafloor). The large amount of hydrate and free gas estimated (7.21x10¹¹ m³ and 4.1x10¹⁰ m³, respectively), the high seismicity, the mechanically unstable nature of the sediments, and the anomalous geothermal conditions, set the stage for potential massive releases of methane to the ocean mainly through hydrate dissociation and/or migration directly to the seabed through faults. We conclude that the Chile Triple Junction is an important methane seepage area and should be the focus of novel geological and ecological research.

As an important element of methane prevention in mining facilities, measurements of concentration serve to obtain information about methane hazards. Information about methane concentration must be linked to the place and time of its occurrence to create valuable data for ongoing hazard analysis. The article presents the results of a methane hazard analysis based on an airflow and methane concentration model, validated using measurement data. Subsequently, simulations of crew movement and the operation of individual methane detectors working according to the algorithms of the Methane Hazard Detection System were conducted based on this model.

This study explored techniques with enteric methane (CH4) abating potential, ranging from chemical additives including 3-NOP, nitrate, and halogenated compounds to natural feed additives such as tannins, oils, seaweed extracts, and probiotics. Most of the evaluated strategies exert their influence either by promoting the growth of ruminal microbes that compete with methanogens for metabolic hydrogen as their resource or by directly consuming CH4. Additionally, externally supplied probiotics, including propionate-forming bacteria and methane-oxidizing bacteria, are a promising tool. However, challenges persist in implementing these strategies effectively. High doses of chemical additives and plant based secondary metabolites often achieve significant CH4 reduction, but they are associated with negative impact on dry matter intake and digestibility, thus compromising overall animal performance. On the other hand, using lower doses to maintain animal performance may not achieve beneficial CH4 reduction. Furthermore, concerns about the impact of certain additives on human health have led to a shift towards more natural alternatives, but their efficacy and feasibility in vivo necessitate further evaluation. Comprehensive research that integrates data from diverse global experiments on ruminants through meta-analytical approaches is essential. Such research will help in identify strategies that either reduce methane emissions and/or enhance production performance, ensuring sustainable livestock farming practices. In conclusion, mitigating CH4 emissions from ruminant livestock is a complex challenge with wide-ranging implication.

Saprotrophic fungi are key in global carbon cycling, capable of decomposing lignocellulose in wood. This study, for the first time, explores the influence of oxygen (O2) and temperature on methane (CH4) production by two fungi, Laetiporus sulphureus and Pleurotus sapidus. We examined CH4 formation under varying O2 levels (0 to 98%) and temperatures (17, 27, and 40 °C) when the fungi grew on pine wood, beech wood, and grass under sterile conditions. Our findings reveal a strong dependency of fungal CH4 production on O2 mixing ratios. Methane formation was highest when O2 levels exceeded 5%, whilst no CH4 formation was observed after complete O2 consumption by the fungi. Reintroducing O2 immediately resumed fungal CH4 production. When CH4 formation was normalized to O2 consumption (CH4_norm) a different pattern between species was observed. L. sulphureus showed higher CH4_norm rates with higher O2 levels, whereas P. sapidus showed elevated rates between 0-5% O2. Temperature also significantly influenced CH4 and CH4_norm rates, with the highest production at 27 °C, and comparatively lower rates at 17 and 40 °C. These results demonstrate that O2 levels and temperature are critical in controlling fungal CH4 emissions, a consideration necessary for future CH4 source predictions.

The anaerobic digestion (AD) of rumen residues and wheat straw in different proportions of inoculum (66.67, 50, 33.33 %V/V) to substrate and their co-digestion potential have been exhaustively studied in this research. It explores variation of feedstock characteristics such as biodegradability and methane potential during AD and anaerobic co-digestion (ACoD) of rumen residues (RR) with wheat straw (WS), under mesophilic conditions. Comparative performance was made with a organic load rate of 18 gVS/L (with 2:1, 1:1 and 1:2 g/g VS of inoculum to substrate). Among different kinetic models studied (modified Gompertz model, transfer model and logistic function), the AD and ACoD of substrates showed better fit to Gompertz model (R2: 0.977–0.997) indicating variation in lag phase and methane production rate depending on the substrate characteristics. During AD, the methane yield improved as the inoculum ratio increased, however, there was no significant difference in ACoD yield from RR to WS for the inoculum to substrate ratios studied, due to the synergistic effect as a result. of greater biodegradability and optimal conditions (such as the C/N ratio). A comparison of methane generation means indicated that maximum methane production can be achieved by mixing rumen residue (75 %) and wheat straw (25 %) with a C/N ratio of (38.15).

This article affords the question of methane emissions in the context of the ESG framework at the global level. The World Bank ESG-Environmental, Social, and Governance database was used. The data refers to 193 countries for a period between 2011 and 2020. The econometric models used are Panel Data with Random Effects, Panel Data with Fixed Effects, Pooled Ordinary Least Squares-OLS, and Weighted Least Squares-WLS. The impact of methane on the ESG model was calculated through three equations capable of analyzing the impact of methane emissions, respectively, con-cerning the E-Environmental, S-Social, and G-Governance components of the ESG model. The re-sults show that methane emissions tend to increase even in the improvement of ESG conditions at world level.

Methane fermentation of organic waste is one way to minimize organic waste, which accounts for 77% of the global municipal waste stream. The use of biowaste treatment technologies helps to improve the energy independence of the regions. Improving the efficiency of the methane fermentation process by using additives from waste may be an attractive alternative to the original technology. The use of biochar as an additive for methane fermentation has been shown to increase the production potential of biogas. The reasons for the improvement in efficiency are complex among others, it is assumed that the specific surface area of ​​biochar may increase the population of anaerobic organisms. Up to date, there are many researches on the effect of biochar additions on methane fermentation, but there is no research on the effect of sulfur-biochar composite. The composite product in the form of a mixture of biochar and molten sulfur is an interesting area of ​​research. In this experiment additions of the sulfur-biochar composite were tested to improve the fermentation process. The composite consisted of 40% biochar and 60% of sulfur and was added to the process. As results the addition of 1% of the composite increased the biogas potential by 4%.

Abiogenic hydrocarbons are fundamentally important for understanding the deep microbial communities and the origin of life. The generation of abiogenic hydrocarbons was proposed to be limited to ultramafic-hosted hydrothermal systems, fueled by the serpentinization product H₂. Here, we present the discharge of short-chain alkanes from an andesitic rock-hosted Lutao geothermal field in the north Luzon arc, carrying abiotic chemical and isotopic signals. These abiogenic hydrocarbons were generated from CO₂-H₂O-rich fluid inclusions, where the long-term storage since Lutao volcanism (~ 1.3 Ma) allowed overcoming the sluggish kinetics of CO₂ to CH₄ reduction at temperatures of 174 - 206 ^oC. Natural abiogenic production of hydrocarbons, therefore, can be more ubiquitous than previously thought. The hypothesis regarding the origin of methane in Earth’s early atmosphere and its implication to the origin of life may require reconsideration.

Moisture and thermal are the key factors for influencing methane desorption during CBM exploitation. Using high pressure water injection technology into coalbed, new fractures and pathways are formed to methane transport. It is existed a phenomenon of water inhibiting gas flow. This study is focused on various water pressures impacted on gas adsorbed coal samples, then the desorption capacity could be revealed under different conditions. And the results are shown that methane desorption capacity was decreased with water pressure increased at room temperature and the downtrend would be steady until water pressure was large enough. Heating could promote gas desorption capacity effectively, with the increasing of water injection pressures, the promotion of thermal on desorption became more obvious. These results are expected to provide a clearer understanding of theoretical efficiency of heat water or steam injection into coalbed, they can provide some theoretical and experimental guidance on CBM production and methane control.

The proof-of-the-concept of application of low-temperature food waste biochars for the anaerobic digestion (AD) of food waste (the same substrate) was tested. The concept assumes that residual heat from biogas utilization may be reused for biochar production. Four low-temperature biochars produced under two pyrolytic temperatures 300 °C and 400 °C and under atmospheric and 15 bars pressure with 60 minutes retention time were used. Additionally, the biochar produced during hydrothermal carbonization (HTC) was tested. The work studied the effect of a low biochar dose (0.05 gBC x gTSsubstrate-1, or 0.65 gBC x L-1) on AD batch reactors’ performance. The biochemical methane potential test took 21 days and the process kinetics using the first-order model were determined. The results showed that biochars obtained under 400°C with atmospheric pressure and under HTC conditions improve methane yield by 3.6%. It has been revealed that thermochemical pressure influences the electrical conductivity of biochars. The biomethane was produced with a rate (k) of 0.24 d-1, and the most effective biochars increased the biodegradability of FW to 81% in comparison to variants without biochars (75%).

Among various processes, catalytic CO2 methanation has emerged as a promising method for carbon capture and utilization. Therefore, a CO2 methanation reaction studied with experimentally. The extent of coke formation on the catalyst after the reaction was quantitatively studied. Then, four different machine learning model were employed in order to model CO2 methanation process and to predict CO2, CO, CH4, H2 and N2 concentrations at outlet. The results of the machine learning models were consistent with the experimental data. Performances of the proposed regression methods are evaluated with 10-fold cross validation. Random forest and decision tree regression performed the best among other methods by achieving R >0.98 for the output concentrations and were able to outperform other modeling approaches. It was shown that the best result among the literature studies is reached in this study. The results have demonstrated the possibility of simulation of the methanation process via machine learning techniques. These techniques can be used control and optimization of carbon capture.

Researchers have been exploring seaweed to reduce methane (CH4) emissions from livestock. This study aimed to investigate the potential of a red alga, Bonnemaisonia hamifera, as an alternative to mitigate CH4 emissions. B. hamifera, harvested from the West coast of Sweden, was used in an in vitro experiment using a fully automated gas production system. The experiment was a ran-domized complete block design consisting of a 48-h incubation that included a control (grass si-lage) and B. hamifera inclusions at 2.5%, 5.0% and 7.5% of grass silage OM mixed with buffered rumen fluid. Predicted in vivo CH4 production and total gas production were estimated by ap-plying a set of models to the gas production data and in vitro fermentation characteristics were evaluated. The results demonstrated that the inclusion of B. hamifera reduced (P = 0.01) predicted in vivo CH4 and total gas production, and total gas production linearly decreased (P = 0.03) with higher inclusion of B. hamifera. The molar proportion of propionate increased (P = 0.03) while isovalerate decreased (P = 0.04) with inclusion of B. hamifera. There was a tendency for increased (0.06 ≤ P ≤ 0.10) total volatile fatty acid production, as well as lower proportions of butyrate, isobutyrate, and 2-methylbutyrate. Chemical analyses revealed that B. hamifera had moderate concentrations of polyphenols. The iodine content was low and there was no detectable bromo-form, suggesting quality advantages over Asparagopsis taxiformis. Additionally, B. hamifera exhib-ited antioxidant activity comparable to the positive control Resveratrol. The findings of this study indicated that B. hamifera harvested from temperate waters in Sweden possesses capacity to mitigate CH4 in vitro.

The conversion of methane into chemicals is of interest to achieve a decarbonized future. Fuel cells are electrochemical devices commonly used to obtain electrical energy, but can be utilized either for chemicals production or both energy and chemicals cogeneration. In this work, the partial oxidation of methane in fuel cells for electricity generation and valuable chemicals production at the same time is reviewed. For this purpose, different types of methane-fed fuel cells, both low temperature fuel cells, such as PEMFCs and AAEMFCs, and high temperature fuel cells, such as SOFCs, have been used. Also if few works have been devoted to this topic, the promising results drive the development of fuel cells using methane as the source for the cogeneration of power and valuable chemicals.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Shale gas and coalbed methane are energy sources that partly or even mainly consist of methane stored in an adsorbed state in the pores of the organic-rich rock and coal seams. In this study, the graphene nanoslit model is employed to model the nanometer slit pores in shale and coal. The Grand Canonical Monte Carlo (GCMC) and Molecular Dynamics (MD) modelling methods are used to investigate the mechanisms of adsorption and displacement of methane in the slit pore. It was found that the CVFF forcefield resulted in the largest adsorption amount, while the PCFF forcefield resulted in the least. The COMPASS and COMPASS II force fields led to similar results. As the width of the slit pore increases, the adsorption amount of gas molecules increases, and the number density profile of adsorbed methane molecules alters from a single adsorption layer to multi-adsorption layers. The minimum slit pore width at which methane molecules can penetrate the slit pore was found to be 0.7 nm. Moreover, it is demonstrated that by lowering the temperature, the adsorption rate of the methane increases since the adsorption is an exothermic process. Enhancing methane recovery was investigated by the injection of gases such as CO2 and N2 to displace the adsorbed methane. The comparison of adsorption isotherms of gas molecules provided the following order in terms of the amount of adsorption: CO2&gt;CH4&gt;N2.

Subgrid scale models for unresolved turbulent fluxes are investigated with a focus on combustion for space propulsion applications. An extension to the gradient model is proposed, introducing a dependency on the local burning regime. The dynamic behavior of the model's coefficients is investigated, and scaling laws are studied. The discussed models are validated using a DNS database of a high-pressure turbulent fuel-rich methane-oxygen diffusion flame. The operating point and turbulence characteristics are selected to resemble those of modern combustors for space propulsion applications to support the future usage of the devised model in this context.

The decline of fossil fuels, the increase of greenhouse gases and the global demand for energy are driving the search for alternative energy sources. Anaerobic digestion is a promising technology because it can convert organic biomass into biogas. As the climate warms, there is an increase in biomass of plant origin in water bodies, and ecosystems are unable to clean themselves. This work aims to show that macroalgae and aquatic plants can be an excellent raw material for biogas production. By mixing them with co-substrates such as cattle manure, higher biogas and methane yields can be obtained. When Cladophora glomerata and Zostera marina macroalgae are mixed with cattle manure, the biogas yield is up to 458.8 mL/gVS and 397.9 mL/gVS, respectively. Methane concentration remained high and reached 62.4%–64.1%. The obtained research results show the high energy value of biogas and the energy potential of biomass. Macroalgae increased the energy potential of biogas to 22.9 MJ/m3, and the energy potential of biomass reached 2.40 MJ/Kg. Due to its high energy value, biogas produced from the considered substrates can be an excellent alter-native to fossil fuels. Integrating aquatic macroalgae into anaerobic digestion is a promising approach for a waste-free marine and freshwater system.

The study was conducted in the potential mixed farming areas of Bale highland to estimate livestock methane emissions. Using multi-stage purposive sampling, 156 households of the three wealth groups were selected based on their livelihood assets as described under methodology. Structured questionnaires, focus group discussions, key informants interview and field visits were the employed methods during the study. Feed nutrient balance was estimated based on the demand and supply while the livestock methane emissions were estimated according to the IPCC guidelines. Descriptive statistics and one-way ANOVA tests were used to analyze the data. Cattle were the dominant (84.25%) livestock owned by the households. The estimated enteric CH4 emission rate from mature cattle, growing cattle, sheep >1 year, sheep ≤ 1 year, horse and donkey were significantly (P<0.001) higher for the better wealth group while mature cattle (69.78%) shared the highest rate. Though, higher emission rates credited to the large number of animals in the area, cattle stay crucial to the livelihoods of the households, beside the major sources of CH4. In conclusion, the estimated CH4 emissions should be focus areas of interventions. Therefore, proper husbandry and quality feed supply and promotion of farm level livestock technologies should be practiced wisely to increase productivity and protect the environment from emissions of the livestock sector.

The air in subterranean karst cavities is often depleted in methane (CH₄) relative to the atmosphere. Karst is considered a potential sink for the atmospheric greenhouse gas CH₄ because its subsurface drainage networks and solution-enlarged fractures facilitate atmospheric exchange. Karst landscapes cover about 14% of earth’s continental surface, but observations of CH₄ concentrations in cave air are limited to localized studies in Gibraltar, Spain, Indiana (USA), Vietnam, Australia, and by incomplete isotopic data. To test if karst is acting as a global CH₄ sink, we measured the CH₄ concentrations, δ¹³C_CH4, and δ²H_CH4 values of cave air from 33 caves in the USA and three caves in New Zealand. We also measured CO₂ concentrations, δ¹³C_CO2, and radon (Rn) concentrations to support CH₄ data interpretation by assessing cave air residence times and mixing processes. Among these caves, 35 exhibited subatmospheric CH₄ concentrations in at least one location compared to their local atmospheric backgrounds. CH₄ concentrations, δ¹³C_CH4, and δ²H_CH4 values suggest that microbial methanotrophy within caves is the primary CH₄ consumption mechanism. Only 5 locations from 3 caves showed elevated CH₄ concentrations compared to the atmospheric background and could be ascribed to local CH₄ sources from sewage and outgassing swamp water. Several associated δ¹³C_CH4 and δ²H_CH4 values point to carbonate reduction and acetate fermentation as biochemical pathways of limited methanogenesis in karst environments and suggest that these pathways occur in the environment over large spatial scales. Our data show that karst environments function as a global CH₄ sink.

Quantifying methane emissions is essential for meeting near-term climate goals and typically done using methane concentrations measured downwind of the source. One major source of methane that is important to observe and promptly remediate is fugitive emissions from oil and gas productions sites but installing methane sensors at the thousands of sites within a production basin is expensive. In recent years, relatively inexpensive metal oxide sensors have been used to measure methane concentrations at production sites. Current methods used to calibrate metal oxide sensors have been shown to have significant shortcomings resulting in limited confidence in methane concentrations generated by these sensors. To address this, we investigate using machine learning (ML) to generate a model that converts metal oxide sensor output to methane mixing ratios. To generate test data, two metal oxide sensors, TGS2600 and TGS2611, were collocated with a trace methane analyzer downwind of controlled methane releases. Over the duration of the measurements, the trace gas analyzer’s average methane mixing ratio was 2.40 ppm with a maximum of 147.6 ppm. The average calculated methane mixing ratios for the TGS2600 and TGS2611 using the ML algorithm were 2.42 ppm and 2.40 ppm with maximum values of 105.9 ppm and 106.3 ppm, respectively. A comparison of histograms generated using the analyzer and metal oxide sensors mixing ratios show overlap coefficients of 0.95 and 0.94 for the TGS2600 and TGS2611, respectively. Overall, our results showed there was a good agreement between the ML derived metal oxide sensors’ mixing ratios and those generated using the more accurate trace gas analyzer. This suggests that the response of lower-cost sensors calibrated using ML could be used to generate mixing ratios with precision and accuracy comparable to higher price trace methane analyzers. This would improve confidence in low-cost sensors’ response, reduce the cost of sensor deploying, and allow for timely and accurate tracking of methane emissions.

Accurate assessment of shale gas reserves hinges on a detailed characterization of gas and water distribution within shale reservoirs. Despite its importance, the nanoscale behavior of water and methane in deep shale formations, especially under elevated temperatures and pressures, remains poorly understood. This study proposes a novel molecular modeling approach to represent the complex nanocomposite porous media found in deep shale matrices. Leveraging quantitative data from experimental analyses of shale pore composition, we developed a molecular model that accurately reflects the intricate pore-slit structure within a composite of kerogen and illite, common constituents of shale. Employing a hybrid grand canonical Monte Carlo and molecular dynamics simulation technique, we investigated the micro-scale distribution and preferential adsorption sites of water and methane within the shale matrix. Our research further elucidates the impact of water on the pore structure of shale and delineates the co-occurrence patterns of water and methane. The simulations reveal that water and methane share similar adsorption preferences on kerogen surfaces, while methane does not exhibit specific adsorption preferences on water-bearing illite. We also find that the presence of water significantly alters the illite pore space, leading to a reduction in larger pore volumes and a concomitant increase in smaller pores. The decrease in methane content with increasing water content is more pronounced in the shrinkage cracks compared to the kerogen matrix pores and is particularly notable in the macropores of illite. The findings underscore the differential sensitivity of methane content to water levels across various shale pore types. These insights contribute to a deeper theoretical understanding of gas and water distribution mechanisms in deep shale reservoirs, offering valuable support for the evaluation of deep shale gas resource potential.

The aim of this study was to quantify methane (CH4) emissions from dairy cows during milking by maximum amplitude of eructation peaks and compare estimates with other metrics for CH4 emissions. Spot measurements of CH4 and carbon dioxide (CO2) emissions were recorded for at least 7 days of continuous sampling using an infrared gas analyser in a robotic milking station whilst cows were milked. Concentrations of CH4 and CO2 were measured at 1 second intervals. A total of 105,701 CH4 spot measurements were obtained from 2,206 dairy cows on 18 farms. Methane emissions per individual cow were quantified by maximum amplitude of eructation peaks, average area under eructation peaks (integral of eructation), average concentration during milking and ratio of CH4 to CO2 concentration. There was a high correlation (r = 0.71) between CH4 emissions quantified by maximum amplitude and integral of eructation peaks. The correlation between maximum amplitude and average CH4 concentration was low, and there was no correlation between maximum amplitude and ratio of CH4 to CO2. As both approaches identify and extract eructation peaks to quantify enteric CH4 emissions, the substantial association between maximum amplitude and eructation integral was expected.

This study analyzed the anaerobic co-digestion of Inoculum (I), Rubber Plant Effluent (RPE) and Gliricidia leaves (GLS) at different mixing ratios for the simultaneous production of methane and organic fertilizer. The results were analyzed for volatile fatty acids, pH, C/N ratio, and methane production. The organic quality of the substrate mixture before and after anaerobic digestion was analyzed for organic carbon, Kjeldahl nitrogen, potassium, and phosphorus content. The study concluded that the inoculum, Rubber Plant Effluent (RPE), and Gliricidia leaves (GLS) mixed in the ratio of 10:2:2 showed higher methane production than other experiments conducted at different mixing ratios. The nitrogen, Potassium and phosphorus content of the substrates are increased after anaerobic digestion. However, the organic carbon content in the substrate decreased in all experiments. This research recommends the planting of rubber trees and Gliricidia maculata to promote economic development in Mauritania. Keywords: Biogas production; Gliricidia leaves; Methane; Rubber Plant Effluent; Organic Manure

Cities are important sources of anthropogenic methane emissions. Municipal governments can play a role in reducing those emissions to support climate change mitigation, but they need information on the rate of emissions to context mitigation actions and track progress. Here, we examine the application of satellite data from the TROPOspheric Monitoring Instrument (TROPOMI) to estimate city-level methane emissions rates in a case study of the City of Calgary, Alberta, Canada. While satellites are touted as a global methane monitoring system, we found limited observational coverage over Calgary that precluded the reliability of measurement-based models to track the annual emissions. In this work, we integrated valid observations over three years (2020-22) and used mass balance modeling to derive a long-term averaged emission estimate. The column-averaged dry-air mole fraction (XCH4) enhancement over Calgary was small, 4.7 ppb, but within the city boundary, we identified local hot spots in the vicinity of known sources (wastewater treatment facility and landfills). The city-scale emissions estimate from mass balance was 215.4 ± 132.8 t/d CH4. This estimate is approximately four- and six-times larger than estimates from Canada's gridded national inventory report of anthropogenic CH4 emissions and the Emissions Database for Global Atmospheric Research (EDGAR v8.0), respectively. Valid observations are more common in warmer months and occur during a narrow daily overpass timeslot over Calgary – these effects may bias the emissions estimate. Overall, the findings from this case study highlight the challenge of deriving routine (sub-annual to annual) satellite-based estimates of city-scale methane emissions in similar geographic settings and suggest that more granular emissions inventories are needed to improve methane reporting.

Methane is a greenhouse gas and identified as a key driver of near-term climate change. Bottom-up approaches estimate annual methane loss from US natural gas production and transport at 6 Tg, but recent studies suggest this may be an underestimate. To investigate this possibility, an equipment-based emissions inventory, using EPA emission factors, was developed to calculate methane emissions from oil and gas operations in the Delaware Basin, USA. Emission factors and activity data were then updated using contemporary and region-specific measurement data. The original inventory estimated emissions at 315 Gg CH4 y-1 (gas production-normalized rate of 0.6% loss), while the updated inventory estimated emissions of 1,500 Gg CH4 y-1 (2.8% loss). The largest changes resulted from large fugitive emissions from oil production (+430 Gg CH4 y-1), updating maintenance activity emissions (+214 Gg CH4 y-1), considering flaring inefficiency (+174 Gg CH4 y-1), and the inclusion of associated gas venting (+136 Gg CH4 y-1). This study suggests that a systematic underestimate probably exists in current bottom-up inventories and identifies sources currently missing or may be incorrect. We also strongly recommend that emission factors should be validated through direct comparison against measurement campaigns that include long-tail distributions typical of oil and gas activities.

This study investigates the use of Au-doped Pd anodic electrocatalysts on ATO support for the conversion of methane to methanol. The study involves cyclic voltammetry, in-situ Raman spectra, polarization curves, and FTIR analysis to determine the optimal composition of gold and palladium for enhancing the conversion process. The results demonstrate the potential for utilizing methane as a feedstock for producing sustainable energy sources. Pd75Au25/ATO electrode exhibited the highest OCP value, and Pd50Au50/ATO had the highest methanol production value at a potential of 0.05 V. Therefore, it can be concluded that an optimal composition of gold and palladium exists to enhance the conversion of methane to methanol. The findings contribute to the development of efficient and sustainable energy sources, highlighting the importance of exploring alternative ways to produce methanol.

Several red seaweeds have shown to inhibit enteric CH₄ production; however, adaptation of fermentation parameters to their presence is not well understood. The objective of this study was to examine the effect of three red seaweeds (Asparargopsis taxiformis, Mazzaella japonica, Palmaria mollis) on in vitro fermentation, CH₄ production, and adaptation using the rumen simulation technique (RUSITEC). The experiment was conducted as a completely randomized design with four treatments, duplicated in two identical RUSITEC apparatus equipped with eight fermenter vessels each. The four treatments included the control (barley straw and barley silage) and the three red seaweeds added to the control diet at 2% diet DM. The experimental period was divided into four phases including a baseline phase (d 0-7; no seaweed included), adaptation phase (d 8-11; seaweed included in treatment vessels), intermediate phase (d 12-16) and a stable phase (d 17-21). The digestibility of organic matter (P = 0.04) and neutral detergent fibre (P = 0.05) was decreased by A. taxiformis during the adaptation phase, but returned to control levels in the stable phase. A. taxiformis supplementation resulted in a decrease (P < 0.001) in molar proportions of acetate, propionate and total volatile fatty acid (VFA) production, with an increase in molar proportions of butyrate, caproate, and valerate; the other seaweeds had no effect (P > 0.05) on molar proportions or production of individual VFA. A. taxiformis was the only seaweed to suppress CH₄ production (P < 0.001), with the suppressive effect increasing (P < 0.001) across phases. Similarly, A. taxiformis increased (P < 0.001) the production of hydrogen (H₂, %, mL/d) across the adaptation, intermediate and stable phases, with the intermediate and stable phases having greater H₂ production than the adaptation phase. In conclusion, M. japonica and P. mollis did not impact rumen fermentation or inhibit CH₄ production within the RUSITEC. In contrast, we conclude that A. taxiformis is an effective CH₄ inhibitor and its introduction to the ruminal environment requires a period of adaptation; however, the large magnitude of CH₄ suppression by A. taxiformis inhibits VFA synthesis, which may restrict production performance in vivo.

Due to its high short-term global warming potential (GWP) compared to carbon dioxide, methane (CH₄) is a considerable agent of climate change. This research is aimed at analyzing data on methane gathered at the GAW (Global Atmosphere Watch) station of Lamezia Terme (Calabria, Southern Italy) spanning seven years of continuous measurements (2016-2022) and integrating the results with key meteorological data. Compared to previous studies on detected methane mole fractions at the same station, daily-to-yearly patterns have become more prominent thanks to the analysis of a much larger data set. Overall, the yearly increase of methane at the Lamezia Terme station is in general agreement with global measurements by NOAA, though local peaks are present, and an increase linked to Covid-19 is identified. Seasonal changes and trends have proved to be fully cyclic, with the daily cycles being largely driven by local wind circulation patterns and synoptic features. Outbreak events have been statistically evaluated depending on their weekday of occurrence to test possible correlations with anthropic activities. A cross analysis between methane peaks and specific wind directions has also proved that local sources may be deemed responsible for the highest mole fractions.

This study investigates the impact of thin flame combustor design on hydrogen flame characteristics and combustion performance through numerical simulations. Variations in flame shape and combustibility between 100% methane and 100% hydrogen combustion are analyzed. Three combustor header shapes (flat, concave, and convex) are modeled to assess their influence on flame behavior. Results show distinct flow patterns, with concave headers promoting strong central flows and convex headers dispersing the flow outward. Temperature field analysis indicates that hydrogen flames have higher temperatures and shorter quenching distances compared to methane flames. A comparative analysis of combustion products is conducted to evaluate combustion performance and NOx emissions. Consequently, the concave header has high combustibility and increases temperatures and NOx fraction in hydrogen combustion.

The substitution of chemical fertilizers by organic manure plays a critical role in sustainable crop production. Nevertheless, organic amendments promote the global warming potential (GWP) in rice paddies due to increased methane (CH4) emissions. Increasing evidence shows that lime application can reduce CH4 emissions from acidic paddy soils, while it is still not clear whether liming can reduce the GWP in rice fields under organic manure substitution. A two-year field experiment was conducted to investigate the impacts of pig manure substitution and lime application on grain yield, CH4 and nitrous oxide (N2O) emissions in a subtropical double-cropped rice field in China. The experiment consisted of three treatments: chemical fertilization (CF, 100% N from urea), 50% of chemical N substituted by pig manure (1/2N + M), and the 1/2N + M treatment plus lime amendment (1/2N + M + L). On average, 1/2N + M reduced rice yield by 5.65% compared to CF, while lime application had no effect on rice yield. Mean cumulative CH4 emissions were 218.8% higher in 1/2N + M than in CF, whereas 1/2N + M + L reduced CH4 emissions by 36.6% compared to 1/2N + M. Neither pig manure substitution nor lime application affected N2O emissions. Consequently, 1/2N + M increased the GWP and greenhouse gas intensity (GHGI) by 214.6% and 228.3%, respectively, compared to CF. In contrast, 1/2N + M + L reduced the GWP and GHGI by 36.4% and 36.5% compared to 1/2N + M. Lime application can mitigate CH4 emissions and GWP induced by pig manure amendment in double-cropped rice fields.

The mechanical pre-treatment constitutes an unavoidable pre-step prior to biofuels conversion. As the cost of this step is often underestimated, recently researchers have striven to identify and characterize the mechanical pre-treatment effects in terms of post-treatment physical characterization, derived improvement of enzymatic digestibility, and output yields. The status of existing mechanical pre-treatment techniques is reviewed by substrate’s typology for lignocellulose biomass, focusing on comminution techniques. Emphasis has been dedicated to the particle size achieved after treatment, crystallinity breakage and eventual inhibitory phenomena deriving from the application of particle size reduction, which are analysed and discussed.

In this field pot study, effect of drainage method (e.g., intermittent drainage (ID) and continuous flooding (CF)) on greenhouse gas (GHGs: CO2 and CH4) emission was determined from three Korean paddies (BG, MG, and JS series), varying soil properties such as soil texture, labile carbon, and mineral types. Emission of GHGs was evidently influenced by the irrigation, to a different extent, depending on paddy’s redox (Eh) shift upon flooding events. The Eh decline upon flooding was slower in JS pot, where pore-water concentration of ferric and sulfate ions is the highest (~ up to 3-fold) among three paddies. MG pot was 2- to 3-fold percolative than others and the Eh drop during flooding period was the smallest (staying above -50 mV). In ID treatment, CH4 emission (t CO2-eq ha-1 yr-1) was reduced in a wide range by 5.6 for JS pot, 2.08 for BG pot, and 0.29 for MG pot relative to CF, whereas CO2 emissions (t CO2-eq ha-1 yr-1) was increased by 1.25 for JS pot, 1.07 for BG pot, and 0.48 for MG pot due to the enhanced oxidation of labile carbon. Grain yield and aboveground biomass production from ID were no less than those from CF (p &lt; 0.05). Consequently, gain of global warming potential (S GWP) by ID varied as the order of JS (37%) &gt; BG (14%) &gt; MG (~0 %) pots, and negligible effect observed for MG pot is due to the equivalent trade-off between CO2 and CH4. Our findings suggest that the efficacy of ID practice on GHGs emission can be further improved by the consideration of redox response of paddy system.

Dehydroaromatization of methane (MDA) is of great interest as a promising process for processing natural and associated petroleum gases, the main component of which is methane. The rapid loss of catalyst activity because of coke formation hinders the introduction of the DHA methane process into industry. Therefore, the aim of the research was to find ways to improve Mo/ZSM-5 catalysts for MDA. The paper presents the results of the synthesis of high-silica zeolites of the ZSM-5 type with a microporous and micro-mesoporous structure, the preparation of Mo/ZSM-5 catalysts based on them, and the study of the physicochemical and catalytic properties of the obtained samples during the non-oxidative conversion of methane into aromatic hydrocarbons. Zeolite catalysts were investigated by IR spectroscopy, X-ray diffraction, TPD-NH3, SEM, HR-TEM, N2-adsorption. It was found that the addition of carbon black at the stage of synthesis of zeolite type ZSM-5 does not lead to structural changes, the obtained samples have a crystallinity equal to 100%. The creation of the micro-mesoporous structure in Mo/ZSM-5 catalysts lead to an increase in their activity and stability in the process of methane dehydroaromatization. The highest conversion of methane is observed on a 4.0%Mo/ZSM-5 catalyst prepared based on of zeolite synthesized using 1.0% carbon black, and is 13.0% in 20 minutes of reaction, while the benzene yield reaches 7.0%. It has been shown by HR-TEM that a more uniform distribution of the active metal component is observed in a zeolite catalyst with a micro-mesoporous structure than in a microporous zeolite.

Greenhouse gas (GHG) emissions from agriculture are significant contributors to global change. We experimentally manipulated biogeochemical control points of irrigation and nitrogen (N) to examine management strategies that could impact GHG flux, i.e., carbon dioxide (CO2), methane (CH4) and nitrous oxide (N2O) and soil physiochemical changes over a growing season in an arid New Mexico sorghum (Sorghum bicolor (L.) Moench) cropping system. Sorghum is water and N efficient and amenable to environmental stress. Interrogating how crop systems perform in intense heat, aridity and ultraviolet stress of the southwestern US climate can inform future management in areas that produce more food currently, but that will undergo these stresses in the near future. Water was applied at regionally typical rates, or at ~30% below those rates. Timing N to plant needs may reduce N loss and N2O emissions, and we tested this hypothesis by adding equal amounts of fertilizer to all plots, with half receiving all fertilizer at planting versus plots fertilized at 50:50 planting and 30 days post-planting. Gas flux from soil was analyzed via FTIR. More biomass was harvested from the fully irrigated plots; N timing did not significantly affect biomass. Soil pH fluctuated throughout the season in response to both treatments. Carbon dioxide emissions significantly increased in fully irrigated plots through time. Methane uptake was depressed by full irrigation. Nitrous oxide flux was lower in split N plots, but N2O emissions were not impacted by reduced irrigation. These results suggest that arid adapted crops can maintain economically feasible yield, and biogeochemical monitoring within a growing season can help manage for GHG flux.

The present study was conducted to investigate the comparative effects of organic and inorganic forms of sulfur, methyl sulfonyl methane (MSM) and sodium sulfate (SS), on laying performance, egg quality, ileal morphology, ileal volatile fatty acids, and antioxidant and stress markers in various biological samples in aged laying hens. A total of 144, 73-week-old Lohman Brown-Lite laying hens were randomly assigned to one of three experimental diets: basal diet (CONT), CONT + 0.2% MSM (MSM), and CONT + 0.3% SS (SS). The trial lasted for 12 weeks. MSM and SS groups contained 0.07% of sulfur, either organic or inorganic. Dietary MSM did not affect egg production and feed conversion ratio at 12 weeks compared with the CONT group. Dietary sulfur did not affect egg quality except for Haugh unit at 4 weeks which was lowered (P &lt; 0.05) in the SS group. Compared with the CONT group, higher (P &lt; 0.05) villus height and crypt depth ratio was observed in the SS group. None of dietary sulfur affected the percentages of short-chain fatty acids in the ileum. Total antioxidant capacity of liver increased (P &lt; 0.05) in laying hens fed MSM- and SS-added diets compared with the CONT group. The MSM and SS groups lowered (P &lt; 0.05) malondialdehyde (MDA) concentration in serum samples compared with the CONT. Finally, dietary MSM had the lowest (P &lt; 0.05) MDA concentrations in yolk samples. Taken together, our study showed that dietary organic and inorganic sulfur have positive effects on ileal morphology and antioxidant capacity in laying hens. However, SS-mediated inhibition in laying performance needs to be clarified.

The aim of the study was to evaluate the effect of crude protein (CP) levels in concentrate and Sesbania grandiflora pod meal (SG) supplementations on feed intake, rumen fermentation, and methane (CH4) mitigation in Thai purebred beef cattle. Four cattle with 100 ± 5.0 kg body weight were used in this study. A 2 × 2 factorial experiment in a 4 × 4 Latin square design were conducted, in which factor A was the CP contents in concentrate of 14, and 16% of dry matter (DM) and factor B was the supplement contents of SG at 0.4% and 0.6% DM intake, respectively. The results showed that the CP contents in concentrate and SG had no interaction effect on intake, digestibility, ruminal ecologies, ruminal fermentation products, and nitrogen utilization. Increasing CP contents in concentrate did not influence DM intake and nutrients’ digestibility, and SG supplementation at 0.6% significantly (P<0.05) decreased CP digestibility. Increasing CP content to 16% increased significantly (P<0.05) the ruminal ammonia nitrogen (NH3-N) concentration while decreased significantly (P<0.05) the NH3-N concentration, protozoal number, and blood urea nitrogen (BUN) at 4 h post-feeding. The 0.6% supplementation of the SG increased significantly average total volatile fatty acids (VFAs) and propionate (C3) concentration while decreased significantly average acetate (C2), C2:C3 ratio, and CH4 production, which was 2.71% for C2, 13.17% for C2:C3 ratio, and 4.37% for CH4 production lower than 0.4% supplementation. Fecal nitrogen excretion was significantly decreased when supplemented with 0.6% of the SG. In conclusion, 0.6% of the SG supplementation showed a greater effect on intake, rumen manipulation, and CH4 mitigation and would recommend supplementation to a concentrate-based diet containing either 14% or 16% CP content.

The study experimentally investigated a novel approach for producing hydrogen from methane cracking in dielectric barrier discharge catalytic plasma reactor using a nanocatalyst. Plasma-catalytic methane (CH4) cracking was undertaken in a dielectric barrier discharge (DBD) catalytic plasma reactor using Ni/MgAl2O4. The Ni/MgAl2O4 was synthesised through co-precipitation followed customised hydrothermal method. The physicochemical properties of the catalyst were examined using X-ray diffraction (XRD), scanning electron microscopy - energy dispersive X-ray spectrometry (SEM-EDX) and thermogravimetric analysis (TGA). The Ni/MgAl2O4 shows a porous structure spinel MgAl2O4 and thermal stability. In the catalytic-plasma methane cracking, the Ni/MgAl2O4 shows 80% of the maximum conversion of CH4 with H2 selectivity 75%. Furthermore, the stability of the catalyst was encouraging 16 hours with CH4 conversion above 75%, and the selectivity of H2 was above 70%. This is attributed to the synergistic effect of the catalyst and plasma. The plasma-catalytic CH4 cracking is a promising technology for the simultaneous H2 and carbon nanotubes (CNTs) production for energy storage applications.

During the extraction of hard coal in Polish conditions, methane is emitted, which is referred to as mine gas. As a result of the desorption of methane, a greenhouse gas is released from coal seams. In order to reduce atmospheric emissions, methane from coal seams is captured by a methane drainage system. On the other hand, methane, which has been separated into underground mining excavations, is discharged into the atmosphere with a stream of ventilation air. For many years, Polish hard coal mines have been capturing methane to ensure the safety of the crew and the continuity of mining operations. As a greenhouse gas, methane has a significant potential, as it is more effective at absorbing and re-emitting radiation than carbon dioxide. The increase in the amount of methane in the atmosphere is a significant factor influencing global warming, however, it is not as strong as the increase in carbon dioxide. Therefore, in Polish mines, the methane-air mixture captured in the methane drainage system is not emitted to the atmosphere, but burned as fuel in systems, including cogeneration systems, to generate electricity, heat and cold. However, in order for such use to be possible, the methane-air mixture must meet appropriate quality and quantity requirements. The article presents an analysis of changes in selected parameters of the captured methane-air mixture from one of the hard coal mines in the Upper Silesian Coal Basin in Poland. The paper analyses the changes in concentration and size of the captured methane stream through the methane capturing system. The gas captured by the methane drainage system, as an energy source, can be used in cogeneration, when the methane concentration is greater than 40%. Considering the variability of CH4 concentration in the captured mixture, it was also indicated which pure methane stream must be added to the gas mixture in order for this gas to be used as a fuel for gas engines. The balance of power of produced electric energy in gas engines is presented. Possible solutions ensuring constant concentration of the captured methane-air mixture are also presented.

Coalbed Methane(CBM) production enhancement for single wells is a big problem to CBM industrialization. Low production is due to insufficient gas generation by thermogenic. Luckily, Biogenic gas was found in many areas and its supply is assumed to improve coalbed methane production. Therefore, microbial simulation experiment will demonstrate the effectiveness of the assumption. From microbial simulation experiment on different coal ranks, it is found that microbes can use coals to produce biogas under laboratory conditions. With different temperatures for different experiments, it turns out that the gas production at 35 ℃ is greater than that at 15℃,indicating that 35℃ is more suitable for microbes to produce gas. According to quantitative experiments, adding exogenous nutrients or exogenous bacteria can improve CBM production. Moreover, the production enhancement ratio can reach up to 115% under the condition of adding exogenous bacterial species, while the ratio for adding nutrients can be up to 144%.

Atoms in Molecules (AIM), Natural Bond Orbital (NBO), and normal coordinate analysis have been carried out at the global minimum structures of TH₅⁺ (T = C/Si/Ge). All these analyses lead to a consistent structure for these three protonated TH₄ molecules. The CH₅⁺ has a structure with three short and two long C-H covalent bonds and no H-H bond. Hence, the popular characterization of protonated methane as a weakly bound CH₃⁺ and H₂ is inconsistent with these results. However, SiH₅⁺ and GeH₅⁺ are both indeed a complex formed between TH₃⁺ and H₂ stabilized by a tetrel bond, with the H₂ being the tetrel bond acceptor. The three-center-two-electron bond (3c-2e) in CH₅⁺ has an open structure, which can be characterized as a V-type 3c-2e bond and that found in SiH₅⁺ and GeH₅⁺ is a T-type 3c-2e bond. This difference could be understood based on the typical C-H, Si-H, Ge-H and H-H bond energies. Moreover, this structural difference observed in TH₅⁺ can explain the trend in proton affinity of TH₄. Carbon is selective in forming a ‘tetrel bond’ and when it does, it might be worthwhile to highlight it as a ‘carbon bond’.

Based on literature data, an analysis was conducted on the thermodynamic and kinetic dependencies of the thermal decomposition of methane. Course of this process was analysed for both thermal and thermal-catalytic conditions. The elementary reaction, i.e. the synthesis of methane from its elements, including its reversibility, was used as the basis for the for considerations on the kinetic model. The conversion degree was adopted as the kinetic parameter (kinetic variable) since this measure is essential for determining the amount of carbon deposit formed and thus closing the mass balance of this process. Several different kinetic models for the elementary reaction were analysed to determine how do they relate in regard to the constant of the reaction rate. It was determined that regardless of whether the process is catalytic or purely thermal, for temperatures t>900°C, the influence of reversibility of the reaction, has negligible influence on the yield of hydrogen produced, and thus can be omitted from the kinetic models. Special attention was given to iron-based catalysts, analysing the reactivity of Fe/C systems. It was demonstrated that the determined kinetic parameters satisfy the Kinetic Compensation Effect (KCE). Furthermore, by incorporating elements of Transition State Theory (TST), the existence of Entropy-Enthalpy Compensation (EEC) was highlighted. Based on these findings Authors show that through analysis of the changes in activation energy (E=20–421 kJ·mol-1) only an estimate of the optimal process conditions can be found, because the isoconversional temperature is also dependent on the way in which the reaction is conducted (T_{iso}=1200-1450K\ >\ \ T_{eq}). In other words, it was found that strong influences of such factors as T, P, etc. can locally compensate each other. Finally, it was also shown that the relations between KCE and EEC complement each other, which is confirmed by the determined average activation entropy at the isokinetic temperature (∆SB= -275.0 J·(mol·K)-1).

The transition to cleaner energy sources, particularly in hard-to-abate industrial sectors, often requires gradual integration of new technologies. Hydrogen, crucial for decarbonization, is explored as a fuel in blended combustions. Blending or replacing fuels impacts combustion stability and heat transfer rates due to differing densities. An extensive literature review examines blended combustion, focusing on hydrogen-methane mixtures. While industrial burners claim to accommodate up to 20% hydrogen, theoretical support is lacking. A novel thermodynamic analysis methodology is introduced, evaluating methane-hydrogen combustion using the Wobbe index. Findings highlight practical limitations beyond 25% hydrogen volume, necessitating a shift to "totally hydrogen" combustion. Blended combustion can be proposed as a medium-term strategy, acknowledging hydrogen's limited penetration. Higher percentages require burner and infrastructure redesign.

As a major coal country, China faces the issue of significant gas emissions during the coal mining process. This study aims to improve the utilization efficiency of mine gas, reduce greenhouse gas emissions, and promote the low-carbon and green transformation of the coal industry. A 10kW gas regenerative thermal oxidation (RTO) experimental system was constructed. The effects of initial methane concentration, low-temperature flue gas proportion, and operating load on combustion temperature, methane oxidation rate, high-temperature flue gas energy, and system thermal efficiency were studied. The results show that when the combustion temperature is below 600°C, the CH4 combustion reaction cannot proceed effectively, and the system temperature continuously decreases and cannot be maintained stable. The experiment determines the stable operating methane concentration range of RTO. In this experimental system, the lower limit of the initial methane concentration is 0.28%, corresponding to an 86% methane oxidation rate. As the initial methane concentration decreases, the combustion temperature also decreases, and the methane oxidation rate follows suit. The higher the low-temperature flue gas proportion, the higher the combustion temperature, and the system thermal efficiency and output heat decrease with the increase of the low-temperature flue gas proportion. This experiment explores multiple factors affecting regenerative thermal oxidation, providing an basis for ensuring the safe and stable operation of the system and optimization. Improving the thermal insulation and heat exchange performance of the storage body can expand the lower limit of the initial methane concentration, thereby increasing the stability and thermal efficiency of the system.

The UN Sustainable Development Goal 7 Report 2022 is about ensuring access to clean and affordable energy, which is key to the development of agriculture, business, communications, education, healthcare, and transportation. The lack of access to energy hinders economic and human development. Nevertheless, the current pace of progress is insufficient to achieve Goal 7 by 2030. Huge disparities in access to modern sustainable energy persist. Rising commodity, energy and shipping prices have increased the cost of producing and transporting solar photovoltaics modules, wind turbines and biofuels worldwide, adding uncertainty to a development trajectory that is already far below Goal 7 ambitions. Achieving energy and climate goals will require continued policy support and a massive mobilization of public and private capital for clean and renewable energy such as methane from biomass. An important factor in improving methane yield from biomass waste is pre-treatment of the biomass prior to anaerobic digestion. Size reduction of lignocellulose biomass is important for changing and increasing digestibility thus increasing methane yield. A Hollander beater was used as the mechanical pre-treatment machine throughout this study. Results indicate that methane yield is directly proportional to feedstock/Inoculum (F/I) ratio as higher F/I ratio led to higher methane yield. It was observed at an F/I ratio of 0.5 that 5 minutes pre-treatment time produced highest methane yield, while the lowest methane yield was observed at an F/I ratio of 0.2 with 1 minute of pre-treatment time. Methane yield decreased by 30% from 140 mL gTS-1 at F/I ratio 0.5 with 5 minutes pre-treatment time to 98 mL gTS-1 at F/I 0.2 with 5 minutes pre-treatment time. The optimum methane yield was attained at high F/I ratio allowing sufficient nutrient essential for complete degradation of biomass. Overall, this research shows the Hollander beater is not efficient in optimizing methane yield for cardboard.

Considering the increasing interest in understanding the biotic component of methane removal from our atmosphere, it becomes essential to study the physiological characteristics and genomic potential of methanotroph isolates, especially their traits allowing them to adapt to elevated growth temperatures. The genetic signatures of Methylocaldum species have been detected in many terrestrial and aquatic ecosystems. A small set of representatives of this genus has been isolated and maintained in culture. The genus is commonly described as moderately thermophilic, with the growth optimum reaching 50oC for some strains. Here, we present a comparative analysis of genomes of three Methylocaldum strains—two terrestrial M. szegediense strains (O-12 and Norfolk) and one marine strain Methylocaldum marinum (S8). The examination of the core genome inventory of this genus uncovers significant redundancy in primary metabolic pathways, including the machinery for methane oxidation (numerous copies of pmo genes) and methanol oxidation (duplications of mxaF, xoxF1-5 genes), three pathways for one-carbon (C1) assimilation, and two methods of carbon storage (glycogen and polyhydroxyalkanoates). We also investigate the genetics of melanin production pathways, as a key feature of the genus.

Scavenging of atmospheric trace gases has been recognized as one of the lifestyle-defining capabilities of microorganisms in terrestrial polar ecosystems. Several metagenome-assembled genomes of as-yet-uncultivated methanotrophic bacteria, which consume atmospheric CH4 in these ecosystems, have been retrieved in cultivation-independent studies. In this study, we isolated and characterized a representative of these methanotrophs, strain D3K7, from a subarctic soil of Northern Russia. Strain D3K7 grows on methane and methanol in a wide range of temperatures, between 5 and 30°C. Weak growth was also observed on acetate. The presence of acetate in the culture medium stimulated growth at low CH4 concentrations (~100 p.p.m.v.). The finished genome sequence of strain D3K7 is 4.15 Mb in size and contains about 3700 protein-encoding genes. According to the result of phylogenomic analysis, this bacterium forms a common clade with metagenome-assembled genomes obtained from the active layer of a permafrost thaw gradient in Stordalen Mire, Abisco, Sweeden, and the mineral cryosol at Axel Heiberg Island in the Canadian high Arctic. This clade occupies a phylogenetic position in between characterized Methylocapsa methanotrophs and representatives of the as-yet-uncultivated Upland Soil Cluster Alpha (USCα). As shown by the global distribution analysis, D3K7-like methanotrophs colonize mostly northern terrestrial ecosystems, such as polar deserts, subarctic soils, permafrost environments, but also occur in boreal peatlands or high-latitude habitats.

Among the alternatives pointed out as able to make livestock a more efficient activity and reduce its environmental impact, the use of feeds with high digestibility and the use of non-conventional fodder species can be highlighted. Tithonia diversifolia (Hemsl.) A. Gray (TD) has already gained attention as a feed for ruminants. Nonetheless, there has been little discussion about the impacts of this plant on the rumen dynamics that lead to better animal performance. The aim of this study was to assess how increasing levels of TD could affect ruminal microbial biomass synthesis, degradability, and in vitro gas production (IVGP) of diets. Four diets were evaluated: a control diet (TD0: 400 g kg-1 soybean meal and corn grain, and 600 g kg-1 Tifton 85 hay (Cynodon spp)) and three increasing levels of TD (TD9: 90, TD27: 270, and TD45: 450 g kg-1 – dry matter basis) as a replacement for dietary roughage. A 96-hour IVGP assay was carried out and five incubation times (2, 4, 10, 24, and 96 hours) were used for degradability determination. Gas produced, methane (CH4), degradability of organic matter (IVDOM), short-chained fatty acid (SCFA) production, partitioning factor (PF), and microbial biomass (MB) were evaluated among treatments. There was no significant effect (P&gt;0.05) between TD inclusion and IVGP at most incubation times; only at 6 hours of incubation did gas production increase linearly with TD inclusion (R2=0.19; P&lt;0.05). TD inclusion had no effects on CH4. IVDOM increased linearly with TD inclusion at 6 and 10 hours, with TD45 being more degradable than the control diet at 6 hours only. There was a positive linear relationship (R2=0.20; P&lt;0.05) between TD inclusion and PF. TD45 had significantly higher PF values than the control. MB also increased linearly (R2=0.30; P&lt;0.05) with TD inclusion, and all diets with TD had significantly more MB than the control diet. The inclusion of TD at the levels used in this work was revealed to have a positive impact on microbial protein synthesis, which could be related to the higher microbial efficiency of increased substrate quality.

The direct methane to methanol (MTM) oxidation is a grand challenge in catalysis, with profound economical implications for the modern chemical industry. Bioinspired metal-organic frameworks (MOFs) with active iron and copper sites have been emerging very recently as innovative catalytic platforms to accomplish the MTM conversion under mild conditions. This review discusses the current state of the art regarding the application of MOFs with iron and copper catalytic centers to perform the MTM reaction, with a focus on the diverse spectroscopic techniques used to unveil the electronic and structural properties of the MOF catalysts at a microscopic level. We explore the synthetic strategies employed to incorporate iron and copper sites into different MOF topologies, the efficiency and selectivity of the iron- and copper-bearing MOF catalysts, and the ensuing MTM reaction mechanisms proposed on the basis of spectroscopic characterization supported by theory. In particular, we evidence how the combination of complementary spectroscopic tools probing different regions of the electromagnetic spectrum is particularly useful to reach a satisfactory understanding of the key reaction pathways and intermediates. Finally, we provide a critical perspective on future directions to advance the use of MOFs to accomplish the MTM reaction.

We conducted an experiment on lambs to determine the effect of infection with the gastrointestinal nematode (GIN) Haemonchus contortus on growth performance, nutrient composition, microbiota, and ruminal fermentation in vivo and in vitro. Twelve female lambs were equally divided into two groups: uninfected animals (CON) and animals infected with approximately 5000 third-stage ISE larvae derived from the MHCo1 strain of H. contortus (INF). Two lambs per group were killed on days 48, 49, and 50 after infection and ruminal content was collected separately from each lamb. Batch cultures of ruminal fluid from CON and INF were incubated in vitro with 0.25 g meadow hay, a plant mixture and chicory used as substrates. The ruminal populations of protozoa, bacteria, total Archaea, and the archaean orders Methanobacteriales and Methanomicrobiales were significantly higher in INF than CON. In vivo concentrations of n-butyrate, iso-butyrate, and iso-valerate were significantly lower in INF than CON. In vitro values after 24 h of ruminal fermentation varied within the substrate. GIN infection by H. contortus was associated with increased methanogenesis. In conclusion, chicory was a promising substrate for mitigating methane production and may modulate the ruminal microbiome of GIN-infected lambs due to its chemical and phytochemical composition.

Methane (CH4) is the second most significant contributor to climate change after carbon dioxide (CO2), accounting for approximately 20% of the contributions from all the well-mixed greenhouse gases. Understanding the spatiotemporal distributions, and the relevant long-term trends are crucial to identifying the sources, sinks, and impacts on climate. Hyperspectral thermal infrared (TIR) sounders, including the Atmospheric Infrared Sounder (AIRS), the Cross-track Infrared Sounder (CrIS), and the Infrared Atmospheric Sounding Interferometer (IASI), have been used to measure global CH4 concentrations since 2002. This study analyzed nearly twenty years of data from AIRS and CrIS and confirmed a significant increase in CH4 concentrations in the mid-upper troposphere (around 400 hPa) from 2003 to 2020, with a total increase of approximately 85 ppb, representing a +4.8% increase in 18 years. The rate of increase was derived using global satellite TIR measurements is consistent with in-situ measurements, indicating a steady increase starting in 2007 and became stronger in 2014. The study also compared CH4 concentrations derived from the AIRS and CrIS against ground-based measurements from NOAA Global Monitoring Laboratory (GML) and found phase shifts in the seasonal cycles in the middle to high latitudes in the northern hemisphere, which is attributed to the influence of stratospheric CH4 that varies at different latitudes. These findings provide insights into the global budget of atmospheric composition and the understanding of satellite measurement sensitivity of CH4.

This work is devoted to the study of active and stable nickel catalysts for methane dry reforming based on Pr-doped ceria-zirconia obtained by solvothermal continuous method. The studies of physicochemical and catalytic properties of the 5%Ni\Ce0.75Zr0.25-xPrxO2 series showed that Pr introduction leads to an increase in the amount of highly reactive oxygen of the oxide lattice. Praseodymium-based catalysts showed significantly higher reactant conversions. In addition to the nature of support, the method of nickel introduction was also studied - Ni was added both by impregnation and one-pot with mixed oxide preparation. The method of Ni addition was shown to have significant effect on the morphology of the supported active component and, respectively, on the catalytic activity. The 5%Ni/Ce0.75Zr0.15Pr0.1O2 catalyst prepared by one-pot method showed stable operation in the MDR reaction for 30 hours at CO2 and CH4 conversions of ~40% and an H2 yield of ~18% (Т=700°С, τ=10ms).

In dry season paddy farming, the alternate wetting and drying (AWD) irrigation improves water productivity, paddy production, and has the potential to decrease greenhouse gas (GHG) such as methane (CH4) and nitrous oxide (N2O) emissions when compared to continuous flooding (CF). However, there is a lack of research in Bangladesh on the effects of water management on CH4 and N2O emissions. During November 2017–April 2018, participatory on-farm trials were conducted at Feni and Chattogram districts of Bangladesh. Total 105 farmers comprising 20-hectare of land (62 farmers at Feni and 43 farmers at Chattogram district, each location having 10 hectare of land). We compared irrigation water and cost reductions, paddy yield, and CH4 and N2O emissions from paddy fields irrigated using AWD and CF irrigation methods. The CH4 and N2O emissions were determined using the Cool Farm Beta-3 methodology, and the global warming potential (GWP) was estimated using the Intergovernmental Panel on Climate Change-2014 standard approach. The mean results of randomly selected 30 farmers from two locations (15 of each) showed that AWD remarkably decreased irrigation water consumption by about 24% and increased water productivity by 224%. We estimated 23% savings for irrigation costs in AWD. By this time, AWD improved paddy production by 3% over CF. The AWD irrigation resulted in a 47% reduction in cumulative CH4 emissions having a lower CH4 emission factor (0.74 kg ha-1 day-1) than CF (1.39 kg ha-1 day-1). There was no obvious difference in N2O emission between AWD and CF. When compared to CF, AWD decreased the overall GWP by 27% and lowered the GHG intensity by 42%. The CH4 and N2O emissions did not differ substantially between Feni and Chattogram.

The shear failure of surface methane capture borehole (SMCB) is the main cause of shortening life cycle of SMCB but lack of lithological analysis. In order to improve the stability of SMCB and improve efficient drainage period, it is of great significance to investigate the lithology performances for shear failure of SMCB. Based on the direct shear tests and geological method, the results shows that the shear displacement increases as the grain size decreases. Mechanical jump occurs at the lithological boundaries, which is mainly determined by the composition of rock specimens. The cohesion is the mainly possible reason for the step change of shear strength. Lithology with high quartz and low clay may effectively improve shear strength and failure resistance. Boreholes drilled into the weaker siltstone and mudstone sections may potentially experience preferential damage due to the larger shear displacement and shear strength. Protective measures at these sections may improve the stability of the borehole casing. The probing data where it was found that boreholes closure validated the prediction.

This paper deals with the techno-economic study of the hybrid renewable energy system based on energy storage aspect under the form of hydrogen and methane. Indeed, with the intermittency of the renewable energy sources such as photovoltaic and wind energy, several problems of produced energy injection to the power system network can be encountered due to the shortage or the excess of these sources. This situation appeals the use of systems that ensure the stability of network based on the storage of energy surplus into gas using electrolyzer systems, which will be used afterward to cover the eventual shortage. In the present paper, the study of performance of each pathway of methane and hydrogen storage has been performed by the treatment of multiple scenarios via different architecture case studies in an Algerian location. Whereas, the energy produced by the photovoltaic system, the wind energy and the gas micro turbine sources are considered similar in each case. The modeling and simulation of the studied system operation under optimization criteria has been performed in this work, where the main aim is to define the appropriate configuration taking into account the different with low costs of investment, maintenance operation and immediate reactivity with a big storage capacity.

The aim of this study was to investigate the relationship between postprandial glycemic levels based on flash-monitoring and the production of intestinal hydrogen (H2) and methane (CH4) gases based on measurement of the amount of these gases in exhaled air. We studied 14 subjects with type 2 diabetes mellitus (T2DM) and 10 individuals without diabetes (control) with 3 food-load tests with simultaneous determination of gases in exhaled air and assessment of glucose levels. In 15.4% of patients with T2DM, there was a non-significant increase in exhaled H2. How-ever, all subjects in the control group had significant increase in exhaled H2. Moreover, the level of H2 in exhaled breathafter food load in patients with T2DM was lower than in normoglycemic subjects. Also, in normoglycemic subjects there was an inverse correlation between maximum glucose rise and maximum H2 in exhaled air after food load. At the same time in patients with T2DM the level of CH4 in exhaled air directly correlated with the parameters of postprandial glycemia in the test with lactulose. Confirmation of a causal relationship between decreased H2 production, increased intestinal CH4 production, and more severe postprandial glycemia may identify new therapeutic targets in the correction of postprandial glycemia in patients with T2DM.

Treatment wetlands (TWs) are Nature-Based Solutions increasingly used worldwide for wastewater (WW) treatment able to remove mineral and organic pollutants through both physical and biochemical process. Besides the reusable effluent, the TWs produce as main output plant biomass that need to be harvested and disposed at least once a year with significant management costs and TW temporary out of service. This study aims (i) to evaluate the potential of TWs biomass for local energy production and (ii) to understand TW hydraulic conductivity (Ks) effects on the biomass biomethane yield. Specifically, it was addressed by determining the Biochemical Methane Potential of common reed (CR) (Phragmites australis) samples collected at three harvest times from the 10-years-old horizontal subsurface treatment wetland (HSTW) used as a secondary WW treatment system for the IKEA® store located in Catania (Eastern Sicily, Italy). Furthermore, the falling head test was conducted to assess the hydraulic conductivity (Ks) variation in the HSTW, in order to understand the influence on the CR biomethane production. Average methane content values were 130.57 Nm3CH4/tVS (±24.29), 212.70 Nm3CH4/tVS (±50.62) and 72.83 Nm3CH4/tVS (±23.19) in August, September, October 2022, respectively. Ks was correlated with both dry matter (R2 = 0.58) and fiber content (R2 = 0.74) and, consequently, affected the biomethane yield that increased at the Ks increases (R2 = 0.30 in August, R2 = 0.57 in September). In the framework of a circular economy, results showed the successfully possibility of integrating the bioenergy production into TWs. The research could contribute (i) to encourage plant operators to reuse biomass from TWs for local energy production and (ii) to help plant operators to understand Ks effects on the biomass biomethane yield, in order to increase the sustainability of the system and to reduce the maintenance costs.

The use of aerobic granular sludge is a promising and future-proof solution for wastewater treatment. The implementation of this technology requires the development of efficient and cost-effective methods for the management of excess sludge. The aim of the research was to evaluate the effects of hydrodynamic cavitation on the efficiency of aerobic granular sludge digestion. Respirometric measurements were performed at a temperature of 38°C and an initial organic load of 5.0 gVS/L. The changes in the properties of the pre-treated biomass, the kinetics of methane fermentation, the amount and composition of the biogas produced and an energetic evaluation of the process were carried out. A significant influence of hydrodynamic cavitation on the transfer of organic compounds into the dissolved phase was demonstrated. The degree of solubilisation was 37% for COD and 42% and for TOC. The efficiency of CH4 production from the pre-treated sludge reached a value of 496±12 mL/gVS, which corresponds to an increase of 19.6% compared to the raw biomass. The influence of cavitation on the CH4 content of the biogas was not observed. Strong correlations were found between the efficiency of anaerobic digestion and the concentration of dissolved organic compounds and the hydrodynamic cavitation time used. The highest net energy production of 2.89 Wh/gTS was achieved after 15 minutes of pre-treatment.

Psychrophilic anaerobic digestion emerges as an appealing integrated solution for the management of agricultural waste, particularly for farmers in regions where the average temperature does not exceed 26°C, as seen in coffee cultivation. Therefore, this study seeks to assess the biomethane potential of thermochemical treated coffee husk through psychrophilic anaerobic digestion (C3-20°C-w/pretreatment). To examine its viability, outcomes were compared with reactors operating at both mesophilic (C1-35°C) and psychrophilic (C2-20°C) conditions, albeit without the use of pretreated coffee husk. The C3-20°C-w/pretreatment test demonstrated a 36.89% increase (150.47 mL CH4/g VS; 161.04 mL CH4/g COD), while the C1-35°C test exhibited a 24.03% increase (124.99 mL CH4/g VS; 133.77 mL CH4/g COD), both in comparison to the C2-20°C test (94.96 mL CH4/g VS; 101.63 mL CH4/g COD). Notably, the C3-20°C-w/pretreatment trial yielded superior outcomes, accompanied by an associated energy output of 4262.2 KWh/year, sufficient to meet the annual energy demands of 588 residences. This marks an increase of 100 and 217 residences compared to mesophilic and psychrophilic AD of CH without pretreatment, respectively.

Despite the extensive research conducted on ruminal methanogens and anti-methanogenic intervention strategies over the last 50 years, most of the currently researched enteric CH4 abatement approaches have shown limited efficacy. This is largely because of the complex nature of animal production and the ruminal environment, host genetic variability of CH4 production, and an incomplete understanding of the role of the ruminal microbiome in enteric CH4 emissions. Recent sequencing-based studies suggest the presence of methanogenic archaea in extra-gastrointestinal tract tissues, including respiratory and reproductive tracts of cattle. While these sequencing data require further verification by culture-dependent methods, the consistent identification of methanogens with relatively greater frequency in the airway and urogenital tract of cattle plus increasing appreciation of the microbiome-gut-organ axis highlight the potential interactions between ruminal and extra-gastrointestinal methanogenic communities. Thus, a traditional singular focus on ruminal methanogens may not be sufficient, and a holistic approach which takes into consideration of the transfer of methanogens between ruminal, extra-gastrointestinal, and environmental microbial communities is of necessity to develop more efficient and long-term ruminal CH4 mitigation strategies. In the present review, we provide a holistic survey of the methanogenic archaea present in different anatomical sites of cattle and discuss potential seeding sources of the ruminal methanogens.

Freshwater lakes represent a potential source of methane (CH4) to the atmosphere. However, the CH4 emission contribution to the total emission in the littoral zones of lakes, especially emergent macrophytes (e.g., lotus), are poorly known. Lotus, has been cultivated in almost all provinces in China, is not only an aquatic plant but also a kind of vegetables. Two sampling zones (lotus plant and open water) were established in the lake of the middle reaches of Yangtze River. The CH4 emission was measured using a floating opaque chamber and gas chromatography between April to December of the years 2021 and 2022. The results indicated that the flux of CH4 emissions ranged from 0.10 to 59.75 mg m-2 h-1, with an average value of 5.61 mg m-2 h-1 in the open water, while ranged from 0.19 to 57.32 mg m-2 h-1, with an average value of 17.14 mg m-2 h-1 in the lotus plant zone. The maximal CH4 emissions occurred in July and August for the open water, which was highly related to the air and water temperature; whereas it happened in September for the lotus plant zone, due to the fresh organic matter inputting to sediments, CH4 transportation by lotus plant, high soil organic carbon content, and the lower dissolved oxygen concentration. Considering the carbon emissions (both CH4 and CO2) and plant productivity, although the greater CH4 emission occurring in lotus plant zone, it could still represent a potential carbon sink (213 g m-2 yr-1), compared to the open water.

In this study, four experimental treatments were evaluated: (T1) alfalfa hay + concentrate, (50:50%, DM); (T2) alfalfa hay + Leucaena leucocephala + concentrate, (30:20:50%, DM); (T3) alfalfa hay + prickly pear + concentrate, (30:20:50%, DM); and (T4) alfalfa hay + Leucaena leucocephala + prickly pear + concentrate, (30:10:10:50%, DM). NH3-N concentrations in T2 and T4 decreased when replaced alfalfa hay in 20 and 10 %, respectively. Treatments did not affect the concentration of total volatile fatty acids (TVFA) between T3 and T4 (p>0.05); while the concentrations among T1 and T2 were different (P<0.05). T2 showed a reduction of 25.5 % in the methane production when compared to T1(p < 0.05).The lowest concentrations of protozoa were observed in T2 and T4, which contained Leucaena leucocephala (T2) and Leucaena leucocephala + prickly pear (T4) (p<0.05). The highest concentration of total methanogens was recorded in T1 and were different to T2, T3 and T4 (p<0.05). Leucaena leucocephala at a inclusion percentage of 20 % decreased the methane when compared to T1; whereas prickly pear there was not a positive effect the methane production.

The data from the extended system was recorded on-going basis in the archives of the monitoring system, and the multipoint system was directly stored in the methane-anemometers, which allows one to perform a comparative analysis of the obtained records from many methane detectors. An important element of the analyses was the simultaneous registration of the methane concentration in the longwall, together with information on operating time, direction of shearer operation and type of work: mining/cleaning. Mining practice shows that in methane coal mines, methane is often the basic limitation for modern and high-efficiency longwall complexes. The paper reports on selected observations and tests carried out in the Cw-4 longwall in seam 364/2 of the Budryk mine belonging to JSW SA. In observation of the methane level in the Cw-4 longwall, additional sensors installed in the end part of the longwall from the side of the gobs and registration of air velocity and methane concentration in the multipoint system built in the selected longwall cross-section were used, regardless of the air parameters recorded in the monitoring system.

Pore-fractures network play a key role in coalbed methane (CBM) accumulation and production, while the impacts of coal facies on the pore-fractures network performance are still poorly understood. In this work, the research on the pore-fracture occurrence of 38 collected coals from Sangjiang-Muling coal-bearing basins with multiple techniques including mercury intrusion porosimetry (MIP), micro-organic quantitative analysis, and optic microscopy, and its variation controlling of coal face were studied. The MIP curves of 38 selected coals indicating pore structures were subdivided into three typical types including type I of predominant micropores, type Ⅱ of predominant micropores and macropores with good connectivity and type Ⅲ of predominant micropores and macropores with poor connectivity. For coal facies, there are three various coal facies were distinguished, which include lake shore coastal wet forest swamp, the upper delta plain wet forest swamp, tidal flat wet forest swamp with Q-cluster analysis and tissue preservation index - gelification index (TPI-GI) and Wood index - groundwater influence index (WI -GWI). The results show there is positive relationship between tissue preservation index (TPI), wood index (WI) and mesopores (102nm-103nm), while a negative relationship between TPI, WI and macropores/fractures. In addition, groundwater level fluctuations can control the development of type C and D fractures, and the frequency of type C and D fractures shows an ascending trend with increasing GWI, which may be caused by the mineral hydration of the coal. Finally, from the perspective of the pore-fractures occurrence in CBM reservoirs, the wet forest swamp of upper delta plain is considered to be the optimization areas for Sanjiang-Mulinghe coal-bearing basins by a comparative study of various coal facies.

The improvement of the methane combustion activity was observed in cyclic temperature-programmed and isothermal reactions over Pd/ZrO2 catalysts by simple reduction/re-oxidation treatment. The catalytic activity increased during the initial stages of isothermal reaction, and the light-off temperature was lowered as the number of cycles increased in the cyclic temperature-programmed reaction. To reveal the origin of activation, variations in the reduction properties after the activation period were carefully investigated through CH4 temperature-programmed reduction (TPR) measurements. From the CH4-TPR results, it was confirmed that the reduction temperature decreased significantly after activation. The observation of the CH4-TPR peak at relatively low temperatures is directly proportional to the catalytic activity of CH4 combustion. It was therefore concluded that repeated reduction/re-oxidation occurred in the reactant stream, and this phenomenon allowed the combustion reaction to proceed more easily at lower temperatures.

Hydrogen and carbon monoxide over-equilibria have been found computationally in kinetic dependencies of methane reforming catalytic reactions (steam and dry reforming) using conditions of the conservatively perturbed equilibrium (CPE) phenomenon, i.e. at the initial equilibrium concentration of hydrogen or carbon monoxide.  The influence of pressure, temperature, flow rate and composition of the initial mixture on the position of the CPE point (the extremum point) was investigated in a wide domain of parameters. It is demonstrated that the CPE phenomenon significantly increases the product concentration (H2 and CO) at the reactor length which is significantly less than the reactor length required to reach the equilibrium. The CPE-point was interpreted as the “turning point” in kinetic behavior.  Recommendations on the temperature and pressure regimes are different from the traditional ones related to the Le Chatelier’s law. Obtained results provide valuable information on optimal reaction conditions for complex reversible chemical transformations, offering potential applications in chemical engineering processes.

Conventional hydrogen production, as an alternative energy resource, has relied on fossil fuels to produce hydrogen, releasing CO2 into the atmosphere. Hydrogen production via the dry forming of methane (DRM) process is a lucrative solution to utilize greenhouse gases, such as carbon dioxide and methane, by using them as raw materials in the DRM process. However, there are a few DRM processing issues, with one being the need to operate at a high temperature to gain high conversion of hydrogen, which is energy intensive. In this study, bagasse ash, which contains a high percentage of silicon dioxide, was designed and modified for catalytic support. Modification of silicon dioxide from bagasse ash was utilized as a waste material and the performance was explored of bagasse ash-derived catalysts interacting with light irradiation and reducing the amount of energy used in the DRM process. The results showed that the performance of 3%Ni/SiO2 bagasse ash WI was higher than that of 3%Ni/SiO2 commercial SiO2 in terms of the hydrogen product yield, with hydrogen generation initiated in the reaction at 300 °C. Using the same synthesis method, the current results suggested that bagasse ash-derived catalysts had better performance than commercial SiO2-derived catalysts when exposed to an Hg-Xe lamp. This indicated that silicon dioxide from bagasse ash as a catalyst support could help improve the hydrogen yield while lowering the temperature in the DRM reaction, resulting in less energy consumption in hydrogen production.

This paper analyzes the mitigation of enteric methane (CH4) emissions from ruminants with the use of feed additives inhibiting of rumen methanogenesis to limit global temperature increase to 1.5 °C. A mathematical simulation conducted herein predicted that pronounced inhibition of rumen methanogenesis with pure chemicals or bromoform-containing algae can contribute to limit global temperature increase by 2050 to 1.5 °C only if widely adopted at a global level and considering an efficacy higher than obtained in most studies. Currently, the most important limitations to the adoption of antimethanogenic feed additives are probably increased feeding cost without a consistent return in production efficiency, and achieving sustained delivery of inhibitors to the rumens of non-supplemented, extensively ranging animals. Economic incentives, and changes in rumen microbial metabolism caused by inhibiting methanogenesis, could potentially be used to make the methanogenesis inhibition intervention cost effective. Also, the composition of the methanogenic community, and rate of disappearance of inhibitors of methanogenesis in the rumen can influence the effective dose of the inhibitors, and hence the cost of their adoption. Possible means for sustained delivery of antimethanogenic compounds to extensively grazing animals are discussed. Limitations and knowledge gaps of these approaches, and future research directions, are examined.

Greenhouse Gases (GHG) emissions from dairy farms are significant contributors to global warming. However much of the published work on GHG reduction is focused on either Methane (CH4) or Nitrous Oxide (N2O), with few, if any, considering the interactions that changes to farm systems can have on both gases. This paper takes the raw data from a year of activity on a 300 cow commercial dairy farm in Northern Ireland to more accurately quantify the GHG sources by use of a simple predictive model based on IPCC methodology. Differing herd management policies are examined together with the impact of integrating Anaerobic Digestion (AD) into each farm system. Whilst significant success can be predicted in capturing CH4 and Carbon Dioxide (CO2) as biogas and preventing N2O emissions, gains made can be lost in a subsequent process negating some or all of the advantage. The process of extracting value from the captured resource is discussed in the light of current farm parameters together with indications of other potential revenue streams. However, this study has concluded that despite the significant potential for GHG reduction, there is little incentive for widespread adoption of manure based farm scale AD in the UK at this time.

Three rice paddy fields under farmers’ actual management conditions were investigated from May to April at Bibai (43°18′N, 141°44′E), in central Hokkaido, Japan to evaluate the carbon (C) sequestration and contribution of CO2, CH4 and N2O fluxes to a global warming potential (GWP). CH4 and N2O fluxes were measured by placing the chamber over the rice plants covering four hills and CO2 fluxes from rice plants root free space in paddy fields were taken as an indicator of soil microbial respiration (Rm) using the closed chamber method. Annual cumulative Rm ranged from 422 to 519 g C m-2 yr-1; which accounted for 54.7 to 55.5 % mainly during the rice growing season. Annual cumulative CH4 emission ranged from 75.5 to 116 g C m-2 yr-1 and this contribution occurred entirely during the rice growing period. Annual cumulative N2O emission ranged from 0.091 to 0.154 g N m-2 yr-1 and 73.5 to 81.3% of the positive annual N2O emission observed during the winter-fallow season. Soil C sequestration was estimated as the difference between net primary production (NPP) and C loss through Rm, CH4 emission and crop C harvest. The soil C sequestration ranged from -305 to -365 g C m- 2 yr-1, indicating that the C loss could not be compensated for by C input through NPP. Carbon loss was much higher (62 to 66%) in winter-fallow season than growing season. The annual net GWP from the investigated paddy fields ranged from 3823 to 5016 g CO2 equivalent m-2 yr-1. Annual GWPCH4 accounted for 71.9 to 86.1% of the annual net GWP predominantly from the rice growing period. These results indicate that CH4 dominated the rice paddy’s net GWP.

Syntrophic acetate oxidation operates close to the thermodynamic equilibrium and very little is known about the participating organisms and their metabolism. Clostridium ultunense is one of the most abundant syntrophic acetate-oxidising bacteria (SAOB) found in engineered biogas processes operating with high ammonia concentrations. It has been proven to oxidise acetate in cooperation with hydrogenotrophic methanogens. There is evidence that the Wood-Ljungdahl (WL) pathway plays an important role in acetate oxidation. In this study we analysed the physiological and metabolic capacities of C. ultunense on genome scale and conducted a comparative study of all known characterised SAOB, namely Syntrophaceticus schinkii, Thermacetogenium phaeum, Tepidanaerobacter acetatoxydans and Pseudothermotoga lettingae. The results clearly indicated physiological robustness beneficial for anaerobic digestion environments and revealed unexpected metabolic diversity with respect to acetate oxidation and energy conservation systems., Unlike S. schinkii and Th. phaeum, C. ultunense clearly does not employ the oxidative WL pathway for acetate oxidation, as its genome (and that of P. lettingae) lack important key genes. In both those species, a proton motive force is likely formed by chemical protons involving putative electron-bifurcating [Fe-Fe] hydrogenases rather than proton pumps. No genes encoding a respiratory Ech hydrogenase, as involved in energy conservation in Th. phaeum and S. schinkii, were identified in C. ultunense and P. lettingae. Moreover, two respiratory complexes sharing similarities to the proton-translocating ferredoxin:NAD⁺ oxidoreductase (Rnf) and the Na+ pumping NADH:quinone hydrogenase (NQR) were predicted. These might form a respiratory chain involved in reduction of electron acceptors other than protons. However, involvement of these complexes in acetate oxidation in C. ultunense and P. lettingae needs further study. This genome-based comparison provides a solid platform for future meta-proteomics and meta-transcriptomics studies and for metabolic engineering, control and monitoring of SAOB.

The construction of an anaerobic digester coupled with post-digestion low level aeration for agricultural wastewater treatment is described. The digester employs underwater speakers to accelerate the anaerobic digestion process while retaining solids to reduce the strength of the effluent. The digester effluent is sent to a holding tank and fed at a low flow rate to an aeration tank to effect partial nitrification of the wastewater. The outlet of this tank is sent to a settling tank to retain biomass that developed in the aeration tank and the effluent is sent to a small, constructed wetland to further reduce wastewater nitrogen and phosphorus. The wetland was planted with the broadleaf cattail, Typha latifolia, and hence to a retention basin. The system has reduced energy consumption due to both the use of underwater sonic treatment and low-level aeration that is not designed to achieve full nitrification/denitrification but rather to achieve a mixture of ammonium, nitrite, and nitrate that might foster the development of a consortium of organisms (i.e. nitrifiers, Anammox bacteria) that can remediate wastewater ammonium at low cost. Biogas is sent to an inground condenser where different treatments may be tested to remove carbon dioxide and hydrogen sulfide. The system is meant to serve as a complex where various technologies and practices can be evaluated to improve the treatment of agricultural wastewater.

There is a need to find methods to intensify the anaerobic digestion process. One possibility is the use of pre-treatment techniques. Many laboratory tests confirm their effectiveness, but in most cases, there is no verification work carried out on industrial plants. The aim of the research carried out under laboratory conditions and on a large scale was to determine the technological and energy efficiency of the use of hydrodynamic cavitation in the pre-treatment of a waste mixture from dairy farms. It has been shown that hydrodynamic cavitation significantly increases the concentration of organic compounds in the dissolved phase. In the most effective variants, the increase in the content of these indicators was over 90% for both COD and TOC. The degree of solubilisation achieved was 49±2.6% for COD and almost 52±4.4% for TOC. Under laboratory conditions, the highest effects of anaerobic digestion were achieved after 10 minutes of pre-treatment. The amount of biogas was on average 367±18 mL/gCOD and the amount of methane 233±13 mL/gCOD. Further large-scale optimisation trials showed that after 8 minutes of hydrodynamic cavitation, the biogas yield was 327±8 L/kgCOD with a CH4 content of 62.9±1.9%. With this variant, the net energy yield was 66.4±2.6 kWh/day, a value that was 13.9% higher than the original variant with 10 minutes of disintegration and 3.1% higher than the variant without pre-treatment.

The characteristics of excess aerobic granular sludge, related to its structure and chemical composition, limit the efficiency of anaerobic digestion. For this reason, pre-treatment methods and compositions with other organic substrates are used. The aim of the research was to determine the effects of co-digestion of pre-hydrodynamically cavitated aerobic granular sludge with waste fats on the efficiency of methane fermentation under mesophilic and thermophilic conditions. The addition of waste fats improved the C/N ratio and increased its value to 19. The greatest effects were observed in thermophilic anaerobic digestion at 55°C, where a 15% waste fat content in volatile soilds was ensured. This resulted in the production of 1278.2±40.2 mL/gVS biogas and 889.4±29.7 mL/gVS CH4. The CH4 content of the biogas was 69.6±1.3%. The increase in biogas and CH4 yield compared to pure AGS anaerobic digestion was 34.4% and 40.1%, respectively. An increase in the proportion of waste fats in the substrate had no significant effect on the efficiency of methane fermentation.

Multiple sources influence air quality and regional climate in complicated atmospheric emission situations like urban agglomerations. To resolve pollution plumes and source influences in polluted areas, a comprehensive chemical fingerprinting of sources utilizing non-methane hydrocarbons (NMHCs) and the identification of acceptable tracer molecules and emission ratios is required, in contrast to pristine locations, where reliance on a single or a few chemical tracers is frequently sufficient. We have characterized the prevalence of NMHCs fingerprints in the urban areas and quantified the correlation of windspeed with the concentration of these pollutants. eNose sensors and Air quality management stations provide the data to identify the emission sources of such pollutants. Based on our analysis, the average NMHC concentration in 2021 has been recorded 0.424 ppm at point 1 AQMS whereas at point 2 AQMS it was 0.256 ppm. Such outcomes could be attributed to the proximity of emissions sources, the direction and speed of the wind, or both. Moreover, traffic can be a major contributor to pollution levels in any urban area. More research based on a larger dataset is required before definitive conclusions can be drawn, and viable solutions can be proposed.

A new approach to preparing a series of Co/Sm2O3 catalysts for hydrogen production by dry re-forming of methane (DRM) is developed. The catalysts precursors are synthesized by a simple method, including evaporation of aqueous solutions of cobalt and samarium nitrates, followed by a short-term calcination of the resulting material. The as-prepared and spent catalysts are characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), temperature-programmed reduction (H2-TPR), and thermogravimetric analysis (TGA). It is shown that the content of cobalt in the synthesized materials affects their phase composition and carbonization resistance in the DRM reaction. It is demonstrated that preheating under N2 affords catalysts providing stable hydrogen and CO yields of 94-98 % for at least 50 h at 900°C. These yields are among the highest ones currently available for DRM catalysts derived from Co-Sm complex oxides. It is found that reduction in the amount of cobalt in the catalyst and its preheating to an operating temperature of 900°C in a nitrogen flow con-tribute to preventing catalyst carbonization and metal particles sintering.

This study assesses the biomethane (CH4) generation and greenhouse gas (GHG) emissions resulting from municipal solid waste landfilling in Phnom Penh, Cambodia, with a focus on the impact of fugitive CH4 emissions and operation processes in four landfilling scenarios: simple dumping (S1), improved management with leachate treatment (S2), engineered landfill with flaring (S3), and engineered landfill with energy recovery (S4). The study also considered the environmental benefits of carbon sequestration and landfill gas utilization. The LandGEM and IPCC FOD models were used to calculate CH4 generation over the period of 2009-2022, and it was found that approximately 18 and 21 M kg/year of CH4 are released, respectively. The energy potential from CH4 recovery was 51–61 GWh/year. Overall GHG emissions in S2 were the highest, amounting to 409–509 M kg CO2-eq/year, while S1 had lower emissions at 397–496 M kg CO2-eq/year. Flaring captured CH4 in S3 could reduce GHG emissions by at least 55%, and using captured CH4 for electricity production in S4 could mitigate at least 83% of GHG emissions. Electricity recovery (S4) could avoid significant amounts of GHG emissions (˗104.5 kg CO2-eq/tMSW). The study suggests that landfill gas-to-energy could significantly reduce GHG emissions.

Intestinal gases are usually discarded as physiologically inert, useless sub-products of colonic fermentation that must be expelled to prevent discomfort and meteorism. Starting from the observation that many living beings use exogenous and/or endogenous gases to attain evolutionary benefits, we question whether intestinal gases in healthy humans could have underestimated physiological effects, either intestinal or extra-intestinal. We examine gaseous volume, composition, source and local distribution in proximal as well as distal gut, providing extensive data that may serve as reference for future studies. We analyze each one of the most abundant intestinal gases and describe their diffusive patterns, active trans-barrier transport dynamics, chemical properties, intra-/extra-intestinal metabolic effects mediated by intracellular, extracellular, paracrine and distant actions. Discussing the physical properties of the whole intestinal gaseous mixture, we illustrate how changes in volume/pressure can be generated by two different mechanisms, namely, physical muscular gut contraction and biological colonic fermentation, with quite different metabolic outcomes. The experimental gas laws suggest that the gaseous exchanges between lumen and bloodstream are impaired by muscular contraction and improved by muscular relaxation. In turn, the surface-area-to-volume ratio suggests that the gaseous exchanges are impaired by microorganismal overproduction and improved by microorganismal reduction. Further, theoretical stochastic approaches from probability theory indicate that the non-turbulent, random paths of gas molecules inside colonic haustra do not homogenously spread over the whole mucosal surface. This means that the intestinal area available for lumen/blood metabolic exchanges is much less than expected not just in disease states, but also in healthy individuals.

Different types of pockmarks, including single pockmarks, circular pockmarks, elongated pockmarks, chain-type pockmarks and compound pockmarks, were identified in coastal areas around Fujian, China. The sediments associated with pockmarks were mainly silty clay to clay, with a small quantity of silt with fine sand. The sulfate content in the pore water in the sedimentary layers associated with pockmarks decreased with depth from the surface, whereas the free methane content increased with depth. The interaction between sulfate and methane is well known, but differences in the sulfate-methane transitional zone (SMTZ) were observed in different areas with different hydrologic characteristics. The sedimentary SMTZ of the offshore Zhe-min mud wedge was shallow, at 50–70 cm below the seafloor. The sedimentary SMTZ was moderately deep (90–115 cm) in the central bay area and deep (180–200 cm) in the sandy area offshore. This variability in SMTZ depth reflects different amounts of free methane gas in the underlying formations, with a shallower SMTZ indicating a higher free methane content. The free methane had δ13C values of -26.47‰ to -8.20‰ and a biogenic-hybrid genetic type. The flux of sedimentary gas from the pockmark surfaces, calculated according to Fick’s formula, was 2.89 to 18.85 l/m2·a. The shape, size and scale of the pockmarks are directly related to the substrate type and the gas production of the underlying strata and thus vary with the sedimentary environment and development stage. Therefore, different types of pockmarks, in various phases of development, are associated with different sedimentary and dynamical conditions. A single circular pockmark forms by strong methane flux. As the intensity of methane flux weakens, the pockmark becomes elongated in the direction of the water flow because of long-term erosion induced by regular hydrodynamic forces. Finally, under weak intensity of methane flux and the influence of complex hydrodynamic conditions, pockmarks merge to form large-scale, compound pockmarks.

In this work performance improvements are described of a low power consumption non-dispersive infrared (NDIR) methane (CH₄) gas sensor using customised optical thin film bandpass filters (BPF). BPF’s shape the spectral characteristic of the combined mid infrared III-V based light emitting diode (LED)/ photodiode (PD) light source/detector optopair, enhancing NDIR CH₄ sensor performance. The BPF, deposited using a novel microwave plasma assisted pulsed DC sputter deposition process, is deposited at room temperature directly onto the temperature sensitive PD heterostructure. BPF’s comprise germanium (Ge) and niobium pentoxide (Nb₂O₅) alternating high and low refractive index layers respectively. Two different optical filter designs are progressed; with BPF bandwidths (BWs) of 160 nm and 300 nm. Comparison of modelled and measured NDIR sensor performance is described, highlighting maximized signal to noise ratio (SNR) and minimized cross talk performance benefits. BPF spectral stability for various environmental temperature and humidity conditions is demonstrated.

The catalytic decomposition of methane (CDM) process produces hydrogen in a single stage and avoids the CO₂ emission thanks to the formation of high added value carbon nanofilaments as by-product. In this work, Ni monometallic and Ni-Co, Ni-Cu and Ni-Fe bimetallic catalysts are tested in the CDM reaction for the obtention of fishbone carbon nanofibers (CNF). Catalysts, in which Al₂O₃ is used as textural promoter in their formulation, are based on Ni as main active phase for the carbon formation and on Co, Cu or Fe as dopants in order to obtain alloys with an improved catalytic behaviour. Characterization of bimetallic catalysts showed the formation of particles of Ni alloys with a bimodal size distribution. For the doping content studied (5 mol. %), only Cu formed an alloy with a lattice constant high enough to be able to favor the carbon diffusion through the catalytic particle against surface diffusion, resulting in higher carbon formations, longer activity times and activity at 750 °C, where Ni, Ni-Co and Ni-Fe catalysts were inactive. On the other hand, Fe also improved the undoped catalyst performance presenting a higher carbon formation at 700 °C and the obtention of narrow carbon nanofilaments from active Ni₃Fe crystallites.

The real implementation of biogas reforming at industrial scale to obtain interesting products, like hydrogen or syngas, is a developing research field where multidisciplinary teams are continuously adding improvements and innovative technologies. Thus, these works can contribute to the proliferation of green technologies where circular economy and sustainability are present. To assess the sustainability of these processes, there are different tools like life cycle assessment (LCA), which implies a complete procedure where even small details count to consider a certain technology sustainable or not. The aim of this work was to review works where LCA is applied to different aspects of biogas reforming, especially focusing on the role of catalysts, which are essential to improve the efficiency of a certain process, but also present a strong influence on its environmental impact. As a conclusion, catalysts have an influence on LCA through the improvement on the catalytic performance and the impact of their production, whereas other aspects related to biogas or methane reforming could equally influence on their durability or reusability, with the subsequent effect on LCA. Further research about this subject is required in a continuously changing technology with plenty of possibilities.

This research project aimed to address the growing concern about methane emissions from seaweed by developing a Convolutional Neural Network (CNN) model capable of accurately predicting these emissions. The study used PANDAS to read and analyze the dataset, incorporating statistical measures like mean, median, and standard deviation to understand the dataset. The CNN model was trained using the ReLU activation function and mean absolute error as the loss function. Model performance was evaluated through MAPE graphs, comparing the mean absolute percentage error (MAPE) between training and validation sets and between true and predicted emissions, and analyzing trends in yearly greenhouse gas emissions. The results demonstrated that the CNN model achieved a high level of accuracy in predicting methane emissions, with a low MAPE between the expected and actual values. This approach should enhance our understanding of methane emissions from Sargassum, contributing to more accurate environmental impact assessments and effective mitigation strategies.

The relationship between DM yield/cutting and fermentable organic matter (FOM) content of tropical grasses was appropriately investigated to re-access optimal grass maturity to feed dairy cattle. Nine different grass species belonging to the genera: Brachiaria spp. (Mulato II, Ruzi), Panicum spp. (Guinea, Hamil, Mombasa, TD58), and Pennisetum spp. (King, Napier, VA06) were chemically analyzed and subjected to an in vitro gas production (IVGP) test. For 72 h, gas production (GP) was continuously recorded with fully automated equipment. A triphasic, nonlinear, regression procedure was applied to analyse GP profiles. Across all the grasses, it was found that the neutral detergent fiber (NDF) contents increased with increasing maturity of the grass while the CP contents decreased with increasing NDF contents. In all nine grasses, digestible organic matter (dOM) was significantly affected by the week of cutting but IVGP was similar between weeks of cutting in Ruzi, Hamil, Mombasa, and Napier grass. Except for Guinea grass, the lowest dOM values were found when the grasses were cut after ≥ 5 weeks of regrowth. Harvesting grass one or two weeks earlier than normal cutting time is a practically relevant intervention in in-creasing forage quality and productivity of dOM and fermentation potential.

This study evaluated five annual and eleven perennial Indian pasture legumes species for their nutritive value, dry matter, mineral contents and in vitro fermentation parameters, aiming to boost their potential as animal feed. Legume species significantly differed (p<0.05) in organic matter, crud protein (CP), ether extracts, fibres, and protein fractions. Clitoria ternatea (CT) a perennial had higher (p<0.05) buffer soluble protein (477), while neutral detergent soluble protein was highest in annually grown Lablab purpureus (420 g/kg CP). Atylosia scarabaeoides (AS) had higher NSC (392 g/kg DM) than SC (367 g/kg DM). Rapidly degradable fraction (51.7 g/kg tCHO) was lower (p<0.05) than other fractions of carbohydrate. Total digestible nutrients, digestible energy and metabolisable energy varied and values were higher for Desmenthus virgatus and lowest for Stylosanthas seabrana (SSe). The NE values for lactation (NEL), maintenance (NEM) and gain (NEG) were also higher for DV (6.6, 7.95 and 4.28) and lowest for SSe (3.54, 4.24 and 0.58 kJ/g DM), respectively. dry matter intake, digestible DM (DDM) and relative feed value of legumes differed (p<0.05) with mean values of 2.22% body weight, 592 g/kg DM and 102%, respectively. Annual grasses like Dolichos biflorus, Macroptilium atropurpureum, Rhynchosia minima (RM) were found better with micro minerals compared to other perennials. In vitro dry matter degradability, partition factor, short chain fatty acids and microbial protein production of legumes varied (P<0.05) and mean values were 578 g/kg DM, 5.61 mg DDM/mL, 2.42 mm/g and 352 mg/g, respectively. Gas and CH4 production (mL/g and mL/g DDM) varied (p<0.05) being lowest gas from AS (55.5) and highest from CT-blue (141), while CH4 production was lower (p<0.05) from CT-white and AS (8.24 and 9.14) and higher from Arachis glabrata (AG) and Arachis hagenbackii (AH) (15.2 and 15.1). Methane in total gas was low for DV, RM and CT-w (8.99, 9.72 and 9.51%) and loss of DE and ME as CH4 varied (P<0.05) amongst the legumes with mean values of 4.62 and 7.86%, respectively. Based on these findings, each legume offers unique benefits, allowing for tailored combinations of annual and perennial legumes to optimize rumen feed efficiency.

Methane and carbon dioxide are the main contributors to global warming, being the methane effect twenty-five times more powerful than carbon dioxide. Although the sources of methane are diverse, it is a very volatile and explosive gas. One way to store the energy content of methane is its conversion to methanol. Methanol is liquid under ambient conditions, easy to transport and, apart from its use as an energy source, it is a chemical platform that can serve as a starting material for the production of various higher value-added products. Accordingly, the transformation of methane to methanol has been extensively treated in the literature, using traditional catalysts as different types of zeolites. However, in the last years, a new generation of catalysts have emerged to carry out this transformation with higher conversion and selectivity, and more importantly, under mild temperature and pressure conditions. These new catalysts typically involve the use of a highly porous supporting material such as zeolite, or more recently, metal-organic frameworks (MOFs) and graphene, and metallic nanoparticles or a combination of different types of nanoparticles that are the core of the catalytic process. In this review, the characteristics, the catalytic mechanisms, reactors, and the main results of these catalysts are presented as a way to overcome the challenges found in traditional catalysts.

Climate change has become a major concern for developing countries given the risk that it posses on energy and food independence, and on general productivity. Despite having an energy system with low carbon intensity when compared to other Latin American countries, Colombia is already facing climate change impacts and requires urgent efforts to mitigate them. As a developing country, the challenge is bigger as policies for economic growth should be in line with the global commitment of reducing greenhouse gas emissions. With the aim of contributing to the design of climate policies, this study assesses the impact of economic development on the environment by examining the validity of the Environmental Kuznets Curve hypothesis for Colombia. Statistically validated and stable autoregressive distributed lag models are estimated for three different environmental indicators: carbon dioxide emissions, methane emissions, and ecological footprint. Moreover, the effects of other variables such as urbanization, foreign direct investment, value added of agricultural and industrial sectors, and energy use are analyzed with dynamic simulations. Empirical evidence supports a long-run equilibrium relationship among investigated variables and the existence of an inverted U-shaped EKC relationship between Gross Domestic Product (GDP) and methane emissions, and GDP and ecological footprint. Shifting to renewable energy sources and leveraging the use of cleaner technologies in agricultural and industrial sectors are found to be key for economic growth without harming the environment.

The co-electrolysis of CO2 and H2O at intermediate temperature is a viable approach for the power-to-gas conversion that deserves for further investigation, considering the need for green energy storage. The commercial solid oxide electrolyser is a promising device, but it is still facing to solve issues concerning the high operating temperatures and the improvement of gas value. In this paper we reported the recent findings of a simple approach that we have amply suggested for solid oxide cells consisting in the addition of a functional layer coated to the fuel electrode of commercial electrochemical cells. This approach simplifies the transition to the next generation of cells manufactured with the most promising materials currently developed and improves the gas value in the outlet stream of cell. Here, the material in use as a coating layer consisted of a Ni-modified La0.6Sr0.4Fe0.8Co0.2O3 which was developed and demonstrated as promising fuel electrode for solid oxide fuel cells. The results discussed in this paper proved the positive role of Ni-modified perovskite as a coating layer for the cathode, since an improvement of about twice was obtained about the quality of gas produced.

Reducing emissions from the iron and steel industry is essential to achieve the Paris climate goals. A new system to reduce the carbon footprint of steel production is proposed in this article by coupling hydrogen direct reduction of iron ore (H-DRI) and natural gas pyrolysis on liquid metal surface inside a bubble column reactor. If grid electricity from EU is used, the emissions would be 435 kg CO₂/tls without considering methane leakage from the extraction, storage and transport of natural gas. Solid carbon, produced as a by-product of natural gas decomposition, finds applications in many industrial sectors, including as a replacement for coal in coke ovens. Specific energy consumption (SEC) of the proposed system is approximately 6.3 MWh per ton of liquid steel(tls). It is higher than other competing technologies, 3.48 MWh/tls for water electrolysis based DRI, and, 4.3-4.5 MWh/tls for natural gas based DRI and blast furnace-basic oxygen furnace (BF-BOF) respectively. Utilization of large quantities of natural gas, where the carbon remains unused, is the major reason for high SEC. Preliminary analysis of the system revealed that it has the potential to compete with existing technologies to produce CO₂ free steel, if renewable electricity is used. Further studies on the kinetics of the bubble column reactor, H-DRI shaft furnace, design and sizing of components, along with building of industrial prototypes are required to improve the understanding of the system performance.

The key towards a sustainable future is the reduction of mankind’s impact on natural systems via the development of new technologies and the improvement of source apportionment. Though days, years and seasons are arbitrarily set, their mechanisms are based on natural cycles driven by Earth’s orbital periods. This is not the case for weeks, which are a pure anthropic category and are known from literature to influence emission cycles. For the first time since it started data gathering operations, CO (carbon monoxide), CO₂ (carbon dioxide), CH₄ (methane) and eBC (equivalent black carbon) values detected by the Lamezia Terme WMO/GAW station in Calabria, Southern Italy have been evaluated via a two-pronged approach accounting for weekly variations in absolute concentrations, as well as the number of hourly averages exceeding select thresholds. The analyses were performed on seven continuous years of measurements, from 2016 to 2022. Moreso, the two results have been combined into a new parameter: the hereby defined WDWO (Weighed Distribution of Weekly Outbreaks) normalizes weekly trends of CO, CO₂, CH₄ and eBC on an absolute scale as percentages, with the scope of providing regulators and researchers alike with a new tool meant to better evaluate anthropogenic pollution and mitigate its effects.

Large ruminant production is associated with high greenhouse gas emissions (GHGe) intensity, with the highest in southeast Asia being Laos at 102.9 CO2eq/kg meat produced, compared with average global meat emissions intensity of 33 CO2eq/kg. As recent studies in Laos identified emissions control molasses blocks (ECBs) achieved abatement of 470kg CO2eq/20kg block consumed, a study was conducted with a supplement mix with reported methane reducing properties, containing plant tannins and citral extract, salt, molasses and water. Groups of housed dairy buffalo (n=7) and pasture-fed grazing beef cows (n=11) were randomly selected, body condition scores estimated (BCS:1-5) and baseline nasa-oral methane eructation measured daily for 2 weeks. All animals were offered 300-400g/day of the mix for a month, with buffalo accessing abundant fresh cut forages whereas the grazing cows accessing rice straw and pasture declining in quality and quantity due to severe drought. The buffalo consumed all of the mix and retained their BCS of 3, whereas the cattle consumed between 200-300g/day of the mix and their BCS declined from 1.5 to 1.0 during the trial. Analysis of data points (buffalo n=309; cattle n=378) found average methane concentration (AMP) per animal of both cohorts increased over the 2 week baseline period, then declined during the supplementation period by 36% in the buffalo and 18% in cattle cohorts.

The aim of this study was to develop a basic model to predict enteric methane emission from dairy cows and to update operational calculations for the national inventory in Norway. Basic models were developed using a database with 63 treatment means from 19 studies. The database included records for enteric CH4 production (MJ/day), dry matter intake (DMI), and dietary nutrient composition. The basic models were evaluated against an external database (n=36, from ten studies) along with other extant models. When evaluated by low root mean square prediction errors and high concordance correlation coefficients, the developed basic models that included DMI, dietary concentrations of fatty acids and neutral detergent fiber performed slightly better in predicting CH4 emissions than extant models. In order to propose country-specific values for the CH4 conversion factor Ym (% of gross energy intake partitioned into CH4) and thus to carry out the national inventory for Norway, the existing operational model was updated for the prediction of Ym over a wide range of feeding situations using energy corrected milk and dietary concentrate share as predictor variables. Input values of Ym were updated based on the results from the basic models. The predicted Ym ranged from 6.22 to 6.72%. In conclusion, the prediction of CH4 production from dairy cows was improved with the help of newly published data, which enabled an update of the operational model for calculating the national inventory of CH4 in Norway.

This study numerically analyzed the effect of composition and temperature and oxygen concentration changes on the selfignition characteristics of n-heptane/methane blended fuels in order to cope with development of alternative fuels and international environmental regulations. CHEMKIN-PRO is used as the analysis program and the LLNL model is used as the reaction model. The numerical results revealed that on autoignition and ignition delay time were sensitive to changes in fuel composition and oxygen concentration. As the methane ratio increases, OH radicals causing ignition are delayed in generation and the concentration is lowered, thus longer the ignition timing. The oxygen concentration in the mixed fuels are changed to simulate the exhaust gas recirculation and a numerical analysis in then performed. As the oxygen concentration decreases, the ignition delay time longer because the nitrogen gas acts as a thermal load in the combustion chamber.

Abstract: Unusual methane emission and spontaneous combustion of coal induced by the air leakage are both hazards during mining. The most common practice has been to improve mine safety is sealing the mining fractures. In this paper, the methane and geology, coal spontaneous combustion characteristics and the coexistence of methane emission and spontaneous combustion of coal were analyzed. The preparation system of inorganic solidified foam (ISF) in field applications is studied and the working principle of generating device consists of foam generator and mixer was expounded. The technical plan of site construction is that the foam fluids was injected to respectively seal the mining fractures behind hydraulic supports, the cavities of air return corner, and the fractures nearby the coal pillar. After the foam fluids injection, the two stress values in the coal pillar eventually maintained above 15.5Mpa and 13Mpa, respectively. It indicated that the ISF can enhance the bearing stress ability of the coal pillar by transforming the stress state from two dimensional to three dimensional. The methane concentration in the air return corner and air return roadway declined significantly to 0.63% and 0.25%. The differential pressure inside and outside of the 4301(1) goaf fluctuated between -100pa to 150pa and the concentration of CO and O2 declined to 9ppm and 6%. The CO concentration in the air return corner finally reached a stable level of 6ppm. What that all means, the foam fluids can seal the air leakage and inhibit spontaneous combustion of coal effectively.

In recent years, the Canadian dairy sector has faced escalating challenges due to its significant contribution to greenhouse gas emissions, particularly methane. This paper critically examines a spectrum of innovative techniques aimed at mitigating methane emissions within this sector, scrutinizing their cost-effectiveness, efficiency, compatibility with animal welfare standards, and adherence to both existing and prospective Canadian environmental legislations. The discourse commences with an exhaustive overview of contemporary methane reduction methodologies pertinent to dairy farming, followed by a rigorous analysis of their economic feasibility. This includes a detailed cost-benefit analysis, juxtaposed with the efficiency and technological advancements these techniques embody. A pivotal aspect of this examination is the alignment of animal welfare with emission reduction objectives, ensuring that strategies employed do not compromise the health and well-being of dairy cattle. Furthermore, the paper delves into the legislative landscape of Canada, evaluating the congruence of these techniques with current environmental laws and anticipating future regulatory shifts. Performance indicators for emission reduction are critically assessed, establishing benchmarks tailored to the Canadian context. This is complemented by an exploration of the market potential of these innovations, including factors influencing their adoption and scalability in the market. The analysis culminates with a synthesis of case studies and best practices within Canada, offering insights into successful implementations and drawing lessons for future endeavors. This comprehensive approach serves not only to address the immediate environmental and health impacts associated with dairy farming emissions but also contributes significantly to the overarching goal of sustainable development in the agricultural sector.

Since a large amount of sewage sludge (WSS) has been generated daily, it is necessary to explore effective methods for utilizing WSS. Although a photo-fermentation system sometimes alters the characteristics of microbial functions, there are no attempts to perform the photo-fermentation using WSS which is regularly treated under a dark-fermentation style. In this study, the effect of photo-fermentation (photo-irradiation) on anaerobic digestion using WSS was revealed. Photo-irradiation during the anaerobic digestion of WSS significantly reduced the amount of organic acids and hydrogen sulfide and methane production was also suppressed. However, it was shown that the activity of sulfate-reducing bacteria in WSS under the light treatment increased. Photo-irradiation also stimulated the growth of green-sulfur bacteria and induced anoxygenic photosynthesis, by which the fermented samples turned green linking with the consumption of hydrogen sulfide. Finally, a dark/light switching fermentation was able to reduce only hydrogen sulfide while methane production remained the same.

The relaxation processes induced by an exposure of the Ar matrices doped with CH4 (0.1 – 10%) to an electron beam were studied with a focus on the dynamics of radiolysis products – H atoms, H2 molecules, CH radicals, and energy transfer processes. Three channels of energy transfer to dopant and radiolysis products were discussed: by free charge carriers, free excitons and photons from the “intrinsic source” provided by emission of the self-trapped excitons. Radiolysis products along with the total yield of desorbing particles were monitored in a correlated manner. Analysis of methane transformation reactions induced by free excitons showed that the CH radical can be considered as a marker of the CH3 species. The competition between exciton self-trapping and energy transfer to the dopant and radiolysis products has been demonstrated. A nonlinear concentration behavior of the H atoms in doped Ar matrices has been established. Real-time correlated monitoring of optical emissions (H atom and CH3 radicals), particle ejection, and temperature revealed a nonmonotonic behavior of optical yields with a strong luminescence flash after almost an hour of exposure, which correlated with explosive pulse of particle ejection and temperature. The connection of this phenomenon with the processes of energy transfer and radical-radical recombination is discussed.

Abstract: Coal bed methane (CBM) reservoirs are complex systems whose properties differ from those of conventional reservoirs. Coal seams are dual-porosity systems that comprise the porosities of the matrix and cleat system. Gas in the coal seams can be stored as free gas in the cleat system and as adsorbed gas in the porous medium. The flow mechanisms of the natural gas through the formation include desorption, diffusion, and Darcy’s flow regimes. The permeability of CBM reservoirs is more sensitive to pressure variations than conventional gas reservoirs. To study the flow behavior of CBM reservoirs it is mandatory to use a model that considers their unique characteristics. The objective of this study was to propose a physical and mathematical model of production performance for horizontal wells in CBM reservoirs whose permeability is dependent on pressure. A solution for the model was obtained by applying Pedrosa´s transformation, perturbation theory, Laplace transformation, the point source method, and Sthefest´s algorithm. The solution to this problem was validated with previous work thoroughly. The type curves of the model were built and the pressure transient behavior of the model was analyzed and discussed. The effects of several parameters on pressure behavior were also discussed.