Thermal infrared imagery provides temperature information on target objects, and has been widely applied in non-destructive testing. However, thermal infrared imagery is not always able to display detailed textures of inspected objects, which hampers the understanding of geometric entities consisting of temperature information. Although some commercial software has been developed for 3D thermal model displays, the software requires the use of expensive specific thermal infrared sensors. This study proposes a cost-effective method for 3D thermal model reconstruction based on image-based modeling. Two smart phones and a low-cost thermal infrared camera are employed to acquire visible images and thermal images, respectively, that are fused for 3D thermal model reconstruction. The experiment results demonstrate that the proposed method is able to effectively reconstruct a 3D thermal model which extremely approximates its corresponding entity. The total computation time for the 3D thermal model reconstruction is intensive while generating dense points required for the creation of a geometric entity. Future work will improve the efficiency of the proposed method in order to expand its potential applications to in-time monitoring.

The evaluation of landslide hazard in seismic areas is based on a deterministic analysis to define the stability of the sites. However, deterministic analysis is not able to consider various uncertainties in the analysis process. This paper focuses on the results established by the probabilistic seismic hazard analysis and extends the probabilistic landslide hazard analysis to consider the uncertainties of opposing ground deformations and strength. The work studies the areas between Nibbiano and Sant'Erasmo inhabited centres in the Camerino municipality located in central Italy. The current state of the areas shows dangerous conditions for the building structures. In fact, all constructions present evidence of damage caused by both the 2016 earthquake and slope instability. The studies, carried out through careful geological survey and detailed geophysical investigations, are performed to define the geological, geomorphological and hydrogeological characteristics of the areas and also to run a new analysis aimed to define the material stress-strain behavior. Both inhabited Centers are located on debris deposits with highly variable thicknesses. The key point regards the definition of the depth of unstable mass, its position and its extension. Therefore, this contribution aims to summarize the knowledge of the landslide phenomenon that affected the area, trying to interpret its evolution with new field investigations. Indeed, during the first step, related to the geological and geomorphological detailed surveys, a remarkable geological model was obtained to better interpret the slope dynamics in relation to the structures of this section of the ridge. This model was also confirmed by the geophysical investigations. The study involves a more detailed definition of the landslide perimeter. Indeed, to analyze the phenomenon, it was necessary to study both the local seismic amplification with finite element 2D simulations and the slope stability conditions with finite 3D difference simulation.

Pure monocular 3D reconstruction is an ill-posed problem that has attracted the research community's interest due to the affordability and availability of RGB sensors. SLAM, VO, and SFM are disciplines formulated to solve the 3D reconstruction problem and estimate the camera’s ego-motion, so many methods have been proposed. However, most of these methods were not evaluated in large datasets, under various motion patterns, had not been tested under the same metrics, and most of them had not been evaluated following a taxonomy, making their comparison and selection difficult. In this research, we performed a comparison of ten publicly available SLAM and VO methods following a taxonomy, including one method for each category of the primary taxonomy, three machine learning-based methods, and two updates of the best methods, to identify the advantages and limitations of each category of the taxonomy and test if the addition of machine learning or the updates made on those methods improved them significantly. Thus, we evaluated each algorithm under the TUM-Mono benchmark and performed an inferential statistical analysis to identify significative differences through its metrics. Results determined that sparse-direct methods significantly outperformed the rest of the taxonomy, and fusing them with machine learning techniques significantly improves the performance of geometric-based methods from different perspectives.

Aiming to address the issue that the existing multi-view stereo reconstruction methods have insufficient adaptability to the repetitive patterns and weak textures in the multi-view images, this paper proposes a three-dimensional (3D) reconstruction algorithm based on feature enhancement and weight optimization MVSNet (Abbreviated as FEWO-MVSNet). To obtain accurate and detailed global and local features, we first develop an adaptive feature enhancement approach to obtain multi-scale information from the images. Second, we introduce an attention mechanism and a spatial feature capture module to enable high-sensitivity detection for weak texture features. Third, based on the 3D convolutional neural network, the fine depth map for multi-view images can be predicted and the complete 3D model is subsequently reconstructed. Last, we evaluated the proposed FEWO-MVSNet through training and testing on the DTU, BlendedMVS, and Tanks&Temples datasets. The results demonstrate significant superiorities of our method for 3D reconstruction from multi-view images, with our method ranking first in accuracy and second in completeness when compared to the existing representative methods.

While Neural Radiance Fields (NeRF) are gaining increasing interest in various domains as innovative methods for novel view synthesis and image-based reconstruction, their potential application in the realm of Cultural Heritage remains unexplored. Purpose of this paper is to assess the effectiveness of applying NeRF to sets of images of digital heritage objects and sites. The study’s findings demonstrate that NeRF could be valuable when used in combination with or as a comparison to other well-established techniques such as photogrammetry, to expand the possibilities of preserving and presenting heritage assets with enhanced visual fidelity and accuracy. Particularly, NeRF show promising results in improving the rendering of translucent and reflective surfaces, objects with homogeneous textures, and elements with intricate details. In addition, we demonstrate that, when considering the same set of input images (with known camera poses), reducing the image quality or the number of images results in significantly less information loss with NeRF compared to photogrammetry. This suggests that NeRF is preferentially suited for scenarios involving sparse information or low-quality photos or videos, which could be especially valuable in risky or challenging situations.

Two-dimensional ultrasound (2D US) is commonly used in clinical settings for its cost-effectiveness and non-invasiveness, but it is limited by spatial orientation and operator dependency. Three-dimensional ultrasound (3D US) overcomes these limitations by adding a third dimension and enhancing integration with other imaging modalities. Advances in deep learning (DL) have further propelled the viability of freehand image-based 3D reconstruction, broadening clinical applications in intraoperative and point-of-care (POC) settings. This review evaluates state-of-the-art freehand 3D US reconstruction methods that eliminate the need for external tracking devices, focusing on experimental setups, data acquisition strategies, and reconstruction methodologies. PubMed, Scopus, and IEEE Xplore were searched for studies since 2014 following PRISMA guidelines, excluding those using additional imaging or tracking systems other than inertial measurement units (IMUs). Fourteen eligible studies were analyzed, showing a shift from traditional speckle decorrelation towards DL-based methods, particularly Convolutional Neural Networks (CNNs). Variability in datasets and evaluation methods hindered a comprehensive quantitative comparison, but notable accuracy improvements were observed with IMUs and integration of contextual and temporal information within CNNs. These advancements enhance freehand 3D US reconstruction feasibility, though variability limits definitive conclusions about the most effective methods. Future research should focus on improving precision in complex trajectories and adaptability across clinical scenarios.

3D Zernike moments based on 3D Zernike polynomials have been successfully applied to the field of voxelized 3D shape retrieval and have attracted more attention in biomedical image processing. As the order of 3D Zernike moments increases, both computational efficiency and numerical accuracy decrease. Due to this phenomenon, a more efficient and stable method for computing high-order 3D Zernike moments was proposed in this study. The proposed recursive formula for computing 3D Zernike radial polynomials combines the recursive calculation of spherical harmonics to develop a voxel-based algorithm for the calculation of 3D Zernike moments. The algorithm was applied to the 3D shape Michelangelo's David with a size of 150×150×150 voxels. As compared to the method without additional acceleration, the proposed method uses a group action of order sixteen orthogonal group and saving unnecessary iterations, the factor of speed-up is 56.783±3.999 when the order of Zernike moments is between 10 and 450. The proposed method also obtained an accurate reconstructed shape with the error rate (normalized mean square error) of 0.00 (4.17×10^-3) when the reconstruction was computed for all moments up to order 450.

Background: The main objective of this study is to develop a customized metatarsophalangeal implant for the treatment of various conditions affecting this specific joint. This approach involves replacing the joint with a custom implant designed specifically to fit each patient's unique anatomical structure. The need for custom implants stems from the obvious lack of size variety available, which presents a major challenge when, the search for the ideal size implant can be a hard task, also when considering the possibility of extensive modification of the bone to adapt it to the available implant. This adaptation, often synonymous with bone reduction, can cause significant post-operative pain for the patient and impact healing time. Methods: A comparative study of modeling software was carried out to select the perfect software, by defining and comparing the relevant criteria. Similarly, the different biomaterial options were examined and compared to select the one best suited to this project, mentioning the imaging modality used to determine the types of images used for our approach. Finally, the 3D printers used in this work were represented, highlighting their technical characteristics. Findings: A resin metatarsophalangeal implant prototype was created using 3D modeling and reconstruction software and tools. Interpretation: Reconstruction and 3D modeling techniques are revolutionizing implant creation, offering customized solutions for patients suffering from metatarsophalangeal joint disorders caused by a wide range of diseases. These results have significant implications for disability management and rehabilitation, encouraging further exploration and progress.

We present a near real-time solution for 3D reconstruction from aerial images captured by consumer UAVs. Our core idea is to simplify the multi-view stereo problem into a series of two-view stereo matching problems. Our method applies to UAVs equipped with only one camera and does not require special stereo-capturing setups. We found that the neighboring two video frames taken by UAVs flying at a mid-to-high cruising altitude can be approximated as left and right views from a virtual stereo camera. Leveraging GPU-accelerated real-time stereo estimation, efficient PnP correspondence solving algorithms and extended Kalman filter, our system simultaneously predicts scene geometry and camera position/orientation from the virtual stereo cameras. Also, this method allows user selection of varying baseline lengths, which provides more flexibility given the trade-off between camera resolution, effective measuring distance, flight altitude, and mapping accuracy. Our method outputs dense point clouds at a constant speed of 25 frames per second and is validated on a variety of real-world datasets with satisfactory results.

It is time-consuming for acquiring complete data by fully phase encoding in two orthogonal directions along with one frequency encoding direction. Undersampling in the 3D k-space is promising in accelerating such 3D MRI process. Though 3D undersampling can be conducted according to predefined probability density, the density based method is not optimal. Because of the large amount of 3D data and computational cost, it is challenging to perform data-driven and learning-based 3D undersampling and subsequent 3D reconstruction. To tackle this challenge, this paper proposes a deep neural network called EEUR-Net, realized by optimizing specific undersampling patterns for the fully-sampled 3D k-space data. Innovatively, our undersampling algorithm employs an end-to-end deep learning approach to optimize phase encoding patterns and uses a 3D U-Net for image reconstruction of undersampled data. Through end-to-end training, we obtain an optimized 3D undersampling pattern, which significantly enhances the quality of the reconstructed image under the same acceleration factor. A series of experiments on a knee MRI dataset demonstrated that, in comparison to standard random uniform, radial, Poisson and equispaced Cartesian undersampling schemes, our end-to-end learned undersampling pattern considerably improves the reconstruction quality of undersampled MRI images.

The 3D reconstruction of vermiculite-based sealing material was carried out based on CT scanning experiments and Avizo software. The precision and representation of the reconstructed digital core were tested by calculating the pore structure parameters and comparing them with the experimental results of mercury compression. Avizo is a perfect interface with Fluent software to perform micro-scale seepage simulation to explore the distribution of pressure and velocity fields during fluid transport. In this paper, a new approach is proposed to study the penetration leakage of non-metallic gaskets by using equivalent pore networks.

This paper explores the influence of various camera settings on the quality of 3D reconstructions, particularly in indoor crime scene investigations. Utilizing Neural Radiance Fields (NeRF) and Gaussian Splatting for 3D reconstruction, we analysed the impact of ISO, shutter speed, and aperture settings on the quality of the resulting 3D reconstructions. By conducting controlled experiments in a meeting room setup, we identified optimal settings that minimize noise and artifacts while maximizing detail and brightness. Our findings indicate that an ISO of 200, a shutter speed of 1/60 seconds, and an aperture of f/3.5 provide the best balance for high-quality 3D reconstructions. These settings are especially useful for forensic applications, architectural visualization, and cultural heritage preservation, offering practical guidelines for professionals in these fields. The study also highlights the potential for future research to expand on these findings by exploring other camera parameters and real-time adjustment techniques.

The monocular structured light measurement system has low cost, simple algorithms, and a wide measurement range, making it widely applicable in multiple fields. However, in practical applications, the system may be affected by various factors including noise, non-linear intensity, changes in the reflectivity of the object being measured, and the calibration method and accuracy of the system, thereby reducing the measurement accuracy. In order to solve these issues, this paper proposes a new monocular structured light measurement method, mainly comprises the following two points: (a) A denoising algorithm for phase images based on DAE is proposed, which calculates the wrapped phase of the phase-shifted fringes after initial denoising by DAE. Then, a new phase-shifted fringe pattern is generated and input into DAE for iterative denoising, achieving high-performance image denoising and high-precision wrapped phase solution. (b) A new absolute phase height calibration algorithm is proposed, which introduces camera internal and external parameters and uses a two-layer feedforward network to directly establish the relationship between phase and the 3D coordinate system. Without the need for high-precision motion platforms, high-precision phase height calibration is attainable. In general, compared to conventional methods, the experimental results indicate the effectiveness of the proposed method for low-quality phase-shifted fringe 3D reconstruction. In addition, the measurement method described in this article also demonstrates effectiveness in high-dynamic scenes.

Reconstructing 3D indoor scenes from 2D images has always been an important task in computer vision and graphics applications. For indoor scenes, traditional 3D reconstruction methods suffer from the lack of surface details, poor reconstruction of large flat surface textures and areas with uneven lighting, and many falsely reconstructed floating debris noises in the reconstructed models. We add adaptive normal priors to the neural implicit reconstruction process to optimize the network, and improve the accuracy of volume density prediction by adding regularization terms to the neural radiation field to constrain the volume density obtained by weight distribution, and learn a smooth SDF surface from the network to obtain an explicit mesh model. Experiments show that the method proposed in this paper outperforms the state-of-the-art methods on ScanNet, Hypersim, and Replica datasets.

Traditional 3D reconstruction models have consistently encountered a challenge: attaining high recall of object edges while preserving precision. In this paper, we introduce a post-processing method Multi-Head Attention Refiner (MA-R) aimed at tackling this challenge by integrating a multi-head attention mechanism within the U-Net style refiner module. The 3D reconstruction model applying this method demonstrates excellence in parsing intricate image details, resulting in significant enhancement of boundary predictions and increased recall rates. In our experiments, our method significantly enhances the reconstruction performance of Pix2Vox++ when multiple images are utilized as input. Specifically, it achieves an enhanced Intersection Over Union score of approximately 1.1% compared to the original Pix2Vox++ model when 16-view images are employed.

There has been considerable research on reconstructing 3D shapes from single-view images; however, preserving the detailed information of the input image remains difficult. In this paper, we propose the application of a gradient map to train a network, aimed at improving the visual quality of fine-grained details such as the thin and tiny components of generated shapes. Each gradient map was created from the original voxel data, and each value represented the amount of information per volume. Here, the gradient map was defined by several methods that mathematically quantify and represent the detailed structure of an object. By applying this map to the loss function in training, we could induce the network to intensively train partial details, such as thin and narrow parts. We demonstrated that the detailed information was well-recovered when a weight that is proportional to the gradient value was applied to the loss. Furthermore, it is expected that our method will contribute to the development of 3D technologies related to the construction of virtual space for simulation and new customer experience.

3D reconstruction from a single 2D input is a classic problem in the field of computer vision. With the advancements in deep learning, the performance of 3D reconstruction has also significantly improved. The reconstruction task is more difficult for objects with no textures or complex deformations. This paper serves as a review of recent literature on 3D reconstruction from a single view, with a focus on deep learning methods from 2018 to 2021. Due to lack of standard datasets or 3D shape representation methods, it is hard make direct comparisons between all reviewed methods. However, this paper reviews different approaches for reconstructing 3d shape as depth maps, surface normals, point clouds and meshes; along with various loss functions and evaluation metrics used to train and evaluate these methods.

3D object reconstruction from depth image streams using Kinect-style depth cameras has been extensively studied. In this paper, we propose an approach for accurate camera tracking and volumetric dense surface reconstruction assuming a known cuboid reference object is present in the scene. Our contribu¬tion is three-fold. (a) We maintain drift-free camera pose tracking by incorporating the 3D geometric constraints of the cuboid reference object into the image registration process. (b) We reformulate the problem of depth stream fusion as a binary classification problem, enabling high-fidelity surface reconstruction, especially in the con¬cave zones of objects. (c) We further present a surface denoising strategy to mitigate the topological inconsistency (e.g., holes and dangling triangles), which facilitates the generation of a noise-free triangle mesh. We extend our public dataset CU3D with several new image sequences, test our algorithm on these sequences and quantitatively compare them with other state-of-the-art algorithms. Both our dataset and our algorithm are available as open-source content at https://github.com/zhangxaochen/CuFusion for oth-er researchers to reproduce and verify our results.

Three-dimensional reconstruction plays an important role in assisting doctors and surgeons in diagnosing bone defects’ healing progress. Common three-dimensional reconstruction methods include surface and volume rendering. As the focus is on the shape of the bone, volume rendering is omitted. Many improvements have been made on surface rendering methods like Marching Cubes and Marching Tetrahedra, but not many on working towards real-time or near real-time surface rendering for large medical images, and studying the effects of different parameter settings for the improvements. Hence, in this study, an attempt towards near real-time surface rendering for large medical images is made. Different parameter values are experimented on to study their effect on reconstruction accuracy, reconstruction and rendering time, and the number of vertices and faces. The proposed improvement involving three-dimensional data smoothing with convolution kernel Gaussian size 0.5 and mesh simplification reduction factor of 0.1, is the best parameter value combination for achieving a good balance between high reconstruction accuracy, low total execution time, and a low number of vertices and faces. It has successfully increased the reconstruction accuracy by 0.0235%, decreased the total execution time by 69.81%, and decreased the number of vertices and faces by 86.57% and 86.61% respectively.

Aquifer karstic structures, due to their complex nature, present significant challenges in accurately mapping their intricate features. Traditional methods often rely on invasive techniques or sophisticated equipment, limiting accessibility and feasibility. In this paper, we propose a new approach to non-invasive, low-cost 3D reconstruction using a camera that observes the light projection of a simple diving lamp. Our method capitalizes on the principles of structured light, leveraging the projection of light contours onto the karstic surfaces. By capturing the resultant light patterns with a camera, we reconstruct three-dimensional representations of the structures. The simplicity and portability of the equipment required make this method highly versatile, enabling deployment in diverse underwater environments. We validate our approach through extensive field experiments conducted in various aquifer karstic settings. The results demonstrate the efficacy of our method in accurately delineating intricate karstic features with remarkable detail and resolution. Furthermore, the non-destructive nature of this technique minimizes disturbance to delicate aquatic ecosystems while providing valuable insights into the subterranean landscape. This innovative methodology not only offers a cost-effective and non-invasive means of mapping aquifer karstic structures but also opens avenues for comprehensive environmental monitoring and resource management. Its potential applications span hydrogeological studies, environmental conservation efforts, and sustainable water resource management in karstic terrains worldwide.

Single particle analysis with cryogenic electron microscopy (cryo-EM) can determine high resolution structures of macromolecular assemblies. To reconstruct final three-dimension(3D) density map, a reliable initial model is essential and ab-initio reconstruction usually can avoid model bias. The grand challenge for ab-initio reconstruction is to alignment two-dimension(2D) low signal-to-noise ratio(SNR) of particle images with random and unknown parameters. Here we formulate a fast ab initio reconstruction method(named AlignFM) based on Fourier Mellin transform and particle-swarm intelligence optimization(PSO) algorithm. It enables simultaneous 2D alignment and 3D refinement, which can fast generate a reliable 3D map. After experiments on several real datasets. AlignFM shows high performance on fast ab initio reconstruction with a small amount of data.

The 3D reconstruction method using RGB-D camera has a good balance in hardware cost, point cloud quality and automation. However, due to the limitation of inherent structure and imaging principle, the acquired point cloud has problems such as a lot of noise and difficult registration. This paper proposes a three-dimensional reconstruction method using Azure Kinect to solve these inherent problems. Shoot color map, depth map and near-infrared image of the target from six perspectives by Azure Kinect sensor. Multiply the 8-bit infrared image binarization with the general RGB-D image alignment result provided by Microsoft to remove ghost images and most of the background noise. In order to filter the floating point and outlier noise of the point cloud, a neighborhood maximum filtering method is proposed to filter out the abrupt points in the depth map. The floating points in the point cloud are removed before generating the point cloud, and then using the through filter filters out outlier noise. Aiming at the shortcomings of the classic ICP algorithm, an improved method is proposed. By continuously reducing the size of the down-sampling grid and the distance threshold between the corresponding points, the point clouds of each view are continuously registered three times, until get the complete color point cloud. A large number of experimental results on rape plants show that the point cloud accuracy obtained by this method is 0.739mm, a complete scan time is 338.4 seconds, and the color reduction is high. Compared with a laser scanner, the proposed method has considerable reconstruction accuracy and a significantly ahead of the reconstruction speed, but the hardware cost is much lower and it is easy to automate the scanning system. This research shows a low-cost, high-precision 3D reconstruction technology, which has the potential to be widely used for non-destructive measurement of crop phenotype.

Non-destructive testing of metallic objects that may contain embedded defects of different sizes is an important application in many industrial branches for quality control. Most of these techniques allow defect detection and its approximate localization, but very few give enough information for its 3D reconstruction. Here we present a hybrid laser – transducer system that combines remote laser-generated ultrasound excitation and non-contact ultrasonic transducer detection. This fully non-contact method gives access to separating scan areas on different object’s faces and defect details from different angles/perspectives can be analysed. This hybrid system can analyse the whole object’s volume data and allow a 3D reconstruction image of the embedded defects. As a novelty for the signal processing improvement, we use a 2D apodization window filtering technique, applied along with the synthetic aperture focusing algorithm in order to remove the undesired effects of side lobes and wide-angle reflections of propagating ultrasound waves, thus, enhancing the resulting 3D image of the defect. We provide both qualitative and quantitative volumetric results with high accuracy and resolution compared with conventional techniques.

Computed tomography (CT) offers detailed insights into the internal anatomy of patients, partic-ularly for spinal vertebrae examination. However, CT scans are associated with higher radiation exposure and cost compared to conventional X-ray imaging. In this study, we applied a Genera-tive Adversarial Network (GAN) framework to reconstruct 3D spinal vertebrae structures from synthetic biplanar X-ray images, specifically focusing on anterior and lateral views. The synthetic X-ray images were generated using the DRRGenerator module in 3D Slicer, by incorporating segmentations of spinal vertebrae in CT scans for the region of interest focussing. The approach leverages a novel feature fusion technique based on X2CT-GAN to combine information from both views and employs a combination of Mean Squared Error (MSE) loss and adversarial loss to train the generator, resulting in high-quality synthetic 3D spinal vertebrae CTs. A total of n=440 CT data were processed. We evaluated the performance of our model using multiple metrics, in-cluding Mean Absolute Error (MAE) (for each slice of the 3D volume [MAE0] and for the entire 3D volume [MAE]), Cosine Similarity, Peak Signal-to-Noise Ratio (PSNR), 3D Peak Sig-nal-to-Noise Ratio (PSNR-3D), and Structural Similarity Index (SSIM). The average PSNR was 28.394 dB, PSNR-3D was 27.432, SSIM was 0.468, cosine similarity was 0.484, MAE0 was 0.034, and MAE was 85.359. The results demonstrated the effectiveness of the approach in reconstruct-ing 3D spinal vertebrae structures from biplanar X-rays, although some limitations in accurately capturing the fine bone structures and maintaining the precise morphology of the vertebrae were present. This technique has the potential to enhance the diagnostic capabilities of low-cost X-ray machines while reducing radiation exposure and cost associated with CT scans, paving the way for future applications in spinal imaging and diagnosis.

In recent years, with the development of social media, people are more and more inclined to upload text, pictures and videos on the platform to express their personal emotions, thus the number of short videos is increasing and becoming the first choice for people to socialize. Unlike the traditional way, people can convey their personal emotions and opinions through media other than words, such as video images, etc. for external information. Therefore, the expression and analysis of emotions is not only through text, but also through the analysis of emotional needs in images and videos, and the research scholars have customized products for individual users. Compared with pure text content, video information can more intuitively express users' happiness, anger and sorrow, thus short video-related applications have gained more and more popularity among Internet users in recent years. However, not all short videos on social networking sites can accurately express users' emotions, and related text information can more accurately assist sentiment analysis and thus improve accuracy. However, short video sentiment analysis based on video frame images is inaccurate in some scenarios, such as when expressing tears of joy, the sentiment expressed by the user's facial expression and voice are different, which will cause errors in the analysis of sentiment. As a result, researchers began to consider multimodal sentiment analysis to reduce the impact of the above scenarios on short video sentiment analysis. This paper focuses on proposing a sentiment analysis method for short videos. We first propose a residual attention model to make full use of the information in audio to classify the emotions contained in them. Then the text information in the dataset is classified by feature extraction. The key to extract features from text information is not only to retain the semantic information of the text, but also to explore the potential emotional information in the text, so as to ensure the integrity of the text information features. The experiments show that the sentiment analysis model proposed in this paper is more superior than the baselines.

Fatigue remains a challenge especially for high end metal AM parts and materials. From a design perspective, the fatigue limit of an AM solution can be improved upon by optimizing the manufacturing process for a certain material and part. In addition, improved accuracy of design methodologies aids in capturing the features critical for fatigue and quantifies their significance to desired part lifetime as well as providing a basis for their avoidance. In current work we present an overall concept merging thermomechanical process and powder bed solidification modeling to micromechanical analysis of fatigue of the resulting material microstructure. Material features critical to fatigue, particularly surface roughness, internal defects such as porosity and cracks and on the other hand inclusions, can be assessed directly on the basis of AM part microstructure with respect to the resulting fatigue limit. Case analyses consist of maraging steel and nickel alloys. The overall scheme provides a basis for optimization of metal AM solutions against fatigue and multiscale modeling founded basis for fatigue design.

The three-dimensional Ising model on the m$\times$n$\times$l cubic lattice with the screw boundary condition along the ${\bf X}$ direction and the periodic boundary conditions along both ${\bf Y}$ and ${\bf Z}$ directions is exactly solved by using the $2^{mn}$-dimensional representation of the rotation group in $2mn$-dimensions, similar to the Kaufman's spinor approach in two dimensions. The exact partition function is obtained from two sets of $2^{mn-1}$ eigenvalues of the $2^{mn}$-dimensional transfer matrix {\bf V} corresponding to the even and odd eigenvectors, respectively. Such the eigenvalues are determined by the angles of the 2mn-dimensional rotation associated with {\bf V}.

Rapid developments in the field of underwater photogrammetry have given scientists1the ability to produce accurate 3-dimensional (3D) models which are now increasingly used in the representation and study of local areas of interest. This paper addresses the lack of systematic analysis of 3D reconstruction and navigation fusion strategies, as well as associated error evaluation of models produced at larger scales in GPS-denied environments using a monocular camera (often in deep-sea scenarios). Based on our prior work on automatic scale estimation of Structure from Motion (SfM)-based 3D models using laser scalers, an automatic scale accuracy framework is presented. The confidence level for each of the scale error estimates is independently assessed through the propagation of the uncertainties associated with image features and laser spot detections using a Monte Carlo simulation. The number of iterations used in the simulation was validated through the analysis of the final estimate behaviour. To facilitate the detection and uncertainty estimation of even greatly attenuated laser beams, an automatic laser spot detection method, mitigating the effects of scene texture, was developed, with the main novelty of estimating the uncertainties based on the recovered characteristic shapes of laser spots with radially decreasing1 intensities. The effects of four different reconstruction strategies resulting from the combinations of Incremental/GlobalSfM, and thea priori/a posterioriuse of navigation data were analyzed using two distinct survey scenarios captured during the SUBSAINTES 2017 cruise (doi: 10.17600/17001000). The study demonstrates that surveys with multiple overlaps of non-sequential images result in a nearly identical solution regardless of the strategy (SfM or navigation fusion), while surveys with weakly connected sequentially acquired images are prone to produce broad-scale deformation (doming effect) when navigation is not included in the optimization. Thus the scenarios with complex survey patterns substantially benefit from using multi-objective BA navigation fusion. In all cases, the errors in the models are inferior to 5%, with errors often being around 1%. The effects of combining data from multiple surveys were also evaluated. The introduction of additional vectors in the optimization of multi-survey problems successfully accounted for offset changes present in the underwater USBL-based navigation data and thus minimize the effect of contradicting navigation priors. Our results also illustrate the importance of collecting a multitude of evaluation data at different locations and moments during the survey.

Additive manufacturing (3D printing) and computer-aided design (CAD) still have limited up-take in biomedical and bioengineering research and education, despite the significant potential of these technologies. The utility of organ-scale 3D-printed models of living structures is widely appreciated, while the workflows for microscopy data translation into tactile-accessible replicas are not well developed yet. Here, we demonstrate an accessible and reproducible CAD-based methodology for generating 3D-printed scalable models of human cells cultured in vitro and imaged using conventional scanning confocal microscopy and fused deposition modelling (FDM) 3D printing. We termed this technology CiTo-3DP (Cells-in-Touch for 3D Printing). As a proof-of-concept, we created CiTo-3DP models of human pancreatic cancer cells and healthy dermal fibroblasts by using selectively stained nuclei and the cytoskeleton components (f-actin and α-smooth muscle actin). The production of dismountable sets of cellular components was al-so shown. The CiTo-3DP approach can be adapted to comprehensively present various cell types, subcellular structures and extracellular matrices. We envisage that the resulting CAD and 3D printed models could be used for further applications, including but not limited to in silico simulations for biology, medicine, pharmacological research, tissue engineering, morphometrical analysis, multiphysics modelling, education, rehabilitation of visually impaired people, and integration into virtual reality.

Among many other themes, Leonardo da Vinci’s Manuscript B contains several drawings of centrally planned churches, some of which are represented using a plan view paired with a bird’s-eye view. The use of a bird’s-eye instead of an elevation represents an innovative depiction technique, which allows to combine the immediacy of the perspective view with the measurability of the façades, and therefore to describe the three-dimensionality of the buildings. To understand the reasons behind the use of this original technique, the edifices’ shape and classify them we decided to use 3D digital reconstruction techniques, for their ability to avoid misunderstandings in the reconstruction process and in the results. This article describes the method to create the digital models of sixteen churches. A Visual programming language (VPL) script was used as 3D base for modelling the churches achieved from a classification code expressing the aggregative rules of the churches. Then, the geometric process for the construction of the plan and its relationship with the elevation measures was studied for each church. Finally, this information was used for the completion of the 3D models, distinguishing more output variants each time there was an inconsistency between plan and perspective view, a variability of one architectural element or an uncertainty.

This research discusses the development of a software-centered EdTech (Education Technology) class model through the implementation of a course titled "3D Time Machine" at a 4-year university in Republic of Korea over two semesters. The course focused on teaching 3D modeling software, Blender, within the history department. The primary objective of offering this course was to equip students from the digital generation with the capability to manipulate digital technology effectively. Through studying historical materials and accumulating domain knowledge, students could construct their narratives from their unique perspectives. This aimed to foster their proficiency in digital technology operation, preparing them for an education environment increasingly centered around virtual worlds. As the use of virtual worlds gains prominence in educational settings, there is a growing need to incorporate curricula that prepare students to thrive as well-prepared citizens in future societies. Assessing the digital competencies of contemporary university students and designing instructional models with particular attention to their needs is becoming increasingly important. This research draws insights from interviews, conducted in both face-to-face and written formats, with students who participated in the "3D Time Machine" course. The interviews revealed valuable insights that can be actively incorporated into the development of software-centered EdTech instructional models. They reported that they expanded their perceptions as they learned how to make their ideas tangible. The course helped students overcome their fear of digital technology. In conclusion, the course effectively employs 3D modeling technology, a software-centered EdTech, as a core element in helping students develop their narratives rapidly and diversely, thereby playing a crucial role in their ability to articulate their unique perspectives.

In this study, we designed a functional neuro-cardiac model to help us examine the role of neuronal regulation and confirm the importance of neural innervation techniques for cardiac tissue regeneration. A three-dimensional (3D) bioprinted neuro-cardiac scaffold composed of a mixture of gelatin-alginate and alginate-genipin-fibrin hydrogels was developed with a 2:1 ratio of AC16 cardiomyocytes (CMs) and retinoic acid differentiated SH-SY5Y neuronal cells (NCs) respectively. A unique semi-3D bioprinting approach was adopted where the CMs were mixed in the cardiac bioink and printed using an anisotropic accordion design to mimic the physiological tissue architecture in vivo. The voids in this 3D structure were methodically filled in using a NCs-gel mixture and cross-linked. Confocal fluorescent imaging using Microtubule-associated protein 2 (MAP-2) antibodies for labeling NCs, and the MyoD1 antibody for CMs revealed functional coupling between the two cell types in the final cross-linked structure. This data confirmed the development of a physiologically functional neuro-cardiac model that can be used to study neuro-cardiac modulation under physiological and pathological conditions.

Corneal opacity is a leading cause of vision impairment and suffering worldwide. Transplantation can effectively restore vision and reduce chronic discomfort. However, there is a considerable shortage of viable corneal graft tissues. Tissue engineering may address this issue by advancing xeno- keratoplasty as a viable alternative to conventional keratoplasty. In particular, livestock decellularization strategies offer the potential to generate bioartificial ocular prosthetics in sufficient supply to match existing and projected needs. To this end, we have examined the best practices and characterizations that have supported the current state-of-the-art driving preclinical and clinical applications. Identifying the challenges that delimit activities to supplement the donor corneal pool derived from acellular scaffolds allowed us to hypothesize a model for keratoprosthesis applications derived from livestock combining 3D printing and decellularization.

Innovations in engineering education are undergoing a noticeable transformation. Higher education institutions are practicing distance education, remote laboratories, studio pedagogies and several other approaches in order to increase their students’ retention, success, and preparedness for the job market. In engineering education, maker spaces have become popular in the last ten years in universities as well as community colleges, high-schools and community innovation hubs. A large number of engineering colleges have allocated significant spaces, and at some universities entire buildings as maker spaces to be used for curricular and extracurricular activities. Success stories of these types of spaces are well documented. This paper describes the activities and programs held at Tennessee Tech University’s maker space called ‘iMakerSpace.’ These accomplishments include several workforce development activities. The impact and effectiveness of the iMakerSpace is evaluated through analysis of survey data.

We are witnessing the revival of the CAM model, which was already used in the past by some authors studying angiogenesis and anti-cancer drugs, that now offers a refined model to fill, in the translational meaning, the gap between in vitro-in vivo studies. It can be used for a wide range of purposes, from testing cytotoxicity, pharmacokinetics, tumorigenesis, invasion, to action mechanisms of molecules, and validation of new materials from tissue engineering research. CAM model is easy to use with a fast outcome and makes experimental research more sustainable since allowing to replace, reduce and refine pre-clinical experimentation ("3Rs" rules [1]). This re-view aims to highlight some unique potentials that CAM-assay presents; in particular, the authors intend to use in the next future the CAM model to verify, in a microenvironment comparable to in vivo conditions, albeit simplified, the angiogenic ability of functionalized 3D constructs to be used in regenerative medicine strategies in the recovery of skeletal injuries of critical size (CSD) that do not repair spontaneously. For this purpose, organotypic cultures will be planned on sever-al CAMs set up in temporal sequence: a sort of organ model for assessing CSD conducted in the CAM bioreactor, rather than in vivo.

A key component of efforts to identify the biological and drug-specific aspects that contribute to therapeutic failure or unexpected exposure-associated toxicity is the study of drug-intestinal barrier interactions. While methods supporting such assessments are widely described for human therapeutics, there is relatively little information available for similar evaluation in support of veterinary pharmaceuticals. There is, therefore, a critical need to develop novel approaches for evaluating drug-gut interactions in veterinary medicine. Three-dimensional (3D) organoids can address these difficulties in a reasonably affordable system that circumvents the need for more invasive in vivo assays in live animals. However, a first step in the development of such systems is understanding organoid interactions in a 2D monolayer. Given the importance of orally administered medications for meeting the therapeutic need of companion animals, we demonstrate growth conditions under which canine colonoid-derived intestinal epithelial cells survive, mature, and differentiate into confluent cell systems with high monolayer integrity. We further examine the applicability of this canine colonoid-derived 2D model to assess the permeability of three structurally diverse, passively absorbed β-blockers (e.g., propranolol, metoprolol, and atenolol). Both absorptive and secretive apparent permeability (Papp) of these drugs at two different pH conditions were evaluated in canine colonoid-derived monolayers and were compared with that of Caco-2 cells. This proof-of-concept study provides promising preliminary results with regard to the utility of canine-derived organoid monolayers for species-specific assessments of therapeutic drug passive permeability.

Development of novel anti-cancer peptides requires a rapid screening process which can be accelerated by using appropriate in vitro tumor models. Breast carcinoma tissue is a three dimensional (3D) microenvironment, which contains a hypoxic center surrounded by dense proliferative tissue. Biochemical clues provided by such 3D cell mass cannot be recapitulated in conventional 2D culture systems. In this experiment, we evaluate the efficacy of the sandalwood peptide, cyclosaplin on established in vitro 3D silk breast cancer model using invasive MDA-MB-231 cell line. The anti-proliferative effect of the peptide on 3D silk tumor model is monitored by alamar blue assay, with conventional 2D culture as control. The proliferation rate, glucose consumed, LDH, and MMP-9 activity of Human breast cancer cells are higher in 3D constructs compared to 2D. A higher concentration of drug is required to achieve 50% cell death in 3D culture than 2D cultures. The cyclosaplin treated MDA-MB-231 cells showed significant decrease in MMP-9 activity in 3D constructs. Microscopic analysis revealed the formation of cell clusters evenly distributed in the scaffolds. The drug treated cells were less in number, smaller and showed unusual morphology. Overall, these findings indicate the role of cyclosaplin as a promising anti-cancer therapeutics.

Malignant cells cultured in three-dimensional (3D) models have been found to be phenotypically and biochemically different from their counterparts cultured conventionally. Since most of these studies employed solid tumor types, how 3D culture affects multiple myeloma (MM) cells is not well understood. Here, we compared MM cells (U266 and RPMI8226) in a 3D culture model with those in conventional culture. While the conventionally cultured cells were present in single cells or small clusters, MM-3D cells grew in large spheroids. We discovered that STAT3 was the pathway that was more activated in 3D in both cell lines. The active form of STAT3 (phospho-STAT3 or pSTAT3), which was absent in MM cells cultured conventionally, became detectable after 1-2 days in 3D culture. This elevated pSTAT3 level was dependent on the 3D environment, since it disappeared after transferring to conventional culture. STAT3 inhibition using a pharmacological agent, Stattic, significantly decreased the cell viability of MM cells and sensitized them to bortezomib in 3D culture. Using an oligonucleotide array, we found that 3D culture significantly increased the expression of several known STAT3 downstream genes implicated in oncogenesis. Since most primary MM tumors are naturally STAT3-active, studies of MM in 3D culture can generate results that are more representative of the disease.

Glioblastoma (GBM), the most common and aggressive primary brain tumor in adults, remains one of the least treatable cancers. Current standard of care—combining surgical resection, radiation, and alkylating chemotherapy—results in a median survival of only 15 months. Despite decades of investment and research into the development of new therapies, most candidate anti-glioma compounds fail to translate into effective treatments in clinical trials. One key issue underlying this failure of therapies that work in pre-clinical models to generate meaningful improvement in human patients is the profound mismatch between drug discovery systems—cell cultures and mouse models—and the actual tumors they are supposed to imitate. Indeed, current strategies that evaluate the effects of novel treatments on GBM cells in vitro fail to account for a wide range of factors known to influence tumor growth. These include secreted factors, the brain’s unique extracellular matrix, circulatory structures, the presence of non-tumor brain cells, and nutrient sources available for tumor metabolism. While mouse models provide a more realistic testing ground for potential therapies, they still fail to account for the full complexity of tumor-microenvironment interactions, as well as the role of the immune system. Based on the limitations of current models, researchers have begun to develop and implement novel culture systems that better recapitulate the complex reality of brain tumors growing in situ. A rise in the use of patient derived cells, creative combinations of added growth factors and supplements, may provide a more effective proving ground for the development of novel therapies. This review will summarize and analyze these exciting developments in 3D culturing systems. Special attention will be paid to how they enhance the design and identification of compounds that increase the efficacy of radiotherapy, a bedrock of GBM treatment.

This study aims to propose a method for constructing basic digital twin data in South Korea by adhering to international standards and utilizing publicly available data. Specifically, the study focuses on designing and proposing a digital twin data model for buildings, which are the most applicable among the basic digital twin data. To achieve this, the first section provides essential background information, introduces concepts and requirements related to digital twin basic data, and offers a brief overview of CityGML. The second section explains the methodology and data used in this study. The third section presents the main findings: the selection of public data (buildings) for constructing digital twin basic data, the mapping process using CityGML, and the creation of UML diagrams. The fourth section discusses these findings. Finally, the conclusion and suggestions for future research are provided. This approach enhances the accuracy of building-related digital twin data and supports the use of digital twin services in both public and private sectors by enabling various spatial analyses.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

The future of intelligent manufacturing machines involves autonomous selection of process parameters to maximize productivity while maintaining quality within specified constraints. To effectively optimize process parameters, these machines need to adapt to existing uncertainties in the physical system. This paper proposes a novel framework and methodology for feedrate optimization that is based on a physics-informed data-driven digital twin with quantified uncertainty. The servo dynamics are modeled using a digital twin, which incorporates the known uncertainty in the physics-based models and predicts the distribution of contour error using a data-driven model that learns the unknown uncertainty on-the-fly by sensor measurements. Using the quantified uncertainty, the proposed feedrate optimization maximizes productivity while maintaining quality under desired servo error constraints and stringency (i.e., the tolerance for constraint violation under uncertainty) using a model predictive control framework. Experimental results obtained using a 3-axis desktop CNC machine tool and a desktop 3D printer demonstrate significant cycle time reductions of up to 38% and 17% respectively, while staying close to the error tolerances compared to the existing methods.

The issue of equipment layout in multi-floor satellites consists of two primary parts: allocating the equipment to the satellite's layers and placing the equipment in each layer individually. In reviewing the past literature in this field, firstly, the issue of assigning equipment to layers is observed in a few articles and next in the layout part, the non-overlapping constraint has always been a challenge, particularly for components that do not have a circular cross-section. In addition to presenting a heuristic method for allocating equipment to different layers of the satellite, this article presents a robust flexible programming model (RFPM) for the placement of equipment at different layers, taking into account the inherent flexibility of the equipment in placement and the subject of uncertainty. This model is based on the existing uncertainty between the distances of cuboid equipment which has not been addressed in any of the previous research, and by comparing its outputs with cases from past studies, it demonstrates a significantly higher efficiency in placing the equipment and meeting the limit of non-overlapping constraints between the equipment. Finally, it would be possible to reduce the design time in the conceptual and preparatory stages, as well as the satellite's overall size, while still satisfying other constraints like stability and thermal limitations, moments of inertia and centre of gravity.

The aim of this study was to clarify degradation characteristics in each tissue of the knee complex of a medial meniscectomy (MMx)-induced knee osteoarthritis (KOA) animal model using classical methods and a new comprehensive evaluation method called contrast-enhanced X-ray micro-computed tomography (CEX-μCT), which was developed in the study. Surgical MMx was performed in the right knee joints of five male Wistar rats to induce KOA. At 4 wk post-surgery, the synovitis was evaluated using qPCR. Degradations of the articular cartilage of the tibial plateau were evaluated using classical methods and CEX-μCT. Evaluation of the synovitis demonstrated significantly increased expression levels of inflammation-associated marker genes in MMx-treated knees compared to that in sham-treated knees. Evaluation of the articular cartilage using classical methods showed that MMx fully induced degradation of the cartilage. Evaluation using CEX-μCT showed that local areas of the medial cartilage of the tibial plateau were significantly reduced in MMx-treated knees compared to that in sham-treated knees. On the other hand, total cartilage volumes were significantly increased in MMx-treated knees. Based on the findings of this study, the researchers in KOA research could be helped to select an optimal KOA model to discover new drugs.

The aim of this research is to investigate the influence of model height employed in the deep drawing of orthodontic aligner sheets on force transmission and aligner thickness. Forty sheets (Zendura FLX) were thermoformed over four models of varying heights (15, 20, 25, and 30 mm). Normal contact force generated on the facial surface of the upper right central incisor (Tooth 11) was measured using pressure-sensitive films. Aligner thickness around Tooth 11 was measured at five points. A digital caliper and a micro-computed tomography (µ-CT) were employed for thickness measurements. The normal contact force exhibited an uneven distribution across the facial surface of Tooth 11. Model 15 displayed the highest force (88.9±23.2 N), while Model 30 exhibited the lowest (45.7±15.8 N). The force distribution was more favorable for bodily movement with Model 15. Thickness measurements, conducted using a digital caliper and µ-CT, revealed substantial thinning of the aligner after thermoforming. This thinning was most pronounced at the incisal edge (50% of the original thickness) and least at the gingivo-facial part (85%). Additionally, there was a progressive reduction in aligner thickness with increasing model height, which was most significant on the facial tooth surfaces. We conclude that the thermoplastic aligner sheets undergo substantial thinning during the thermoforming process, which becomes more pronounced as the height of the model increases. As a result, there is a decrease in both overall and localized force transmission, which could lead to increased tipping by the aligner and a diminished ability to achieve bodily movement.

With the pressure of the increasing density of urban areas, some public infrastructures are moving to the underground to free up space above, such as utility lines, rail lines and roads. In the big data era, the three dimensional (3D) data can be beneficial to understand the complex urban area. Comparing to spatial data and information of the above ground, we lack of the precise and detailed information about underground infrastructures, such as the spatial information of underground infrastructure, the ownership of underground objects and the interdependence of infrastructures in the above and below ground. How to map reliable 3D underground utility networks and use it in the land administration? First, to explain the importance of this work and find a possible solution, this paper observes the current issues of the existing underground utility database in Singapore. A framework for utility data governance is proposed to manage the work process from the underground utility data capture to data usage. This is the backbone to support the coordination of different roles in the utility data governance and usage. Then, an initial design of the 3D underground utility data model is introduced to describe the 3D geometric and spatial information about underground utility data and connect it to the cadastral parcel for land administration. In the case study, the newly collected data from mobile Ground Penetrating Radar is integrated with the existing utility data for 3D modelling. It is expected to explore the integration of new collected 3D data, the existing 2D data and cadastral information for land administration of underground utilities.

Due to the manufacturing process of Additive Manufacturing (AM) Parts the mechanical properties cannot be predicted. The scope of the present work is to propose a predictive tool for the mechanical properties of AM parts through the use of Adaptive Neuro-Fuzzy Inference System (ANFIS). The Adaptive Neuro-Fuzzy Inference System (ANFIS) combines neural networks with fuzzy logic to generate a mapping between the inputs and the output. Real data experiments from different AM technologies and materials compose the initial dataset so a detailed investigation is conducted to gain knowledge of how different parameters affect the UTS, the elongation and the Young modulus of each experiment. Experimental data were also use to train, check and verify the methodology. The method is tested for FFF technology, PLA material and 3 point bending stress, with interesting results.

Introduction: There is no standardised, universal method to assess physical conditions such as pressure in the pelvicalyceal system in real time during RIRS (retrograde intrarenal surgery). Therefore, the problem concerning increased pressure in the upper urinary tract during the procedure is underestimated. Moreover, it potentially may cause micro-damage and longer postoperative recovery. The aim of this study was to evaluate intrapelvic pressure (IPP) during RIRS procedures. Materials and methods: The 3D printed models of the pelvicalyceal system were printed based on CT-scan of real patient. They were used to perform 50 RIRS procedures with laser lithotripsy of artificially synthesised kidney stones with two different sizes of ureteral access sheath-UAS (10/12Fr vs. 12/14Fr) together with different energy settings generated by the holmium:YAG laser. IPP monitoring during RIRS was performed with the use of the PressureWire X Guidewire compatible with the CoroFlow system. Results and Conclusions: The results showed that high IPP of up to 400 cmH2O would be achieved using a 10/12Fr UAS, while the use of a 12/14Fr UAS would significantly reduce the peak pressure to approximately 100 cmH2O, hence the size of the UAS is a pivotal factor of the IPP generated during the procedure.

Ledge formation presents a significant challenge in endodontic treatment. Yet, there is still a lack of educational tooth models for hands-on practice. This study aimed to create and evaluate a tooth model for ledge management practice. A natural tooth with curved roots was collected for scientific use under ethics committee approval. Following initial root canal preparation, the tooth was scanned using micro-computed tomography (μCT) and 3D reconstructed. A K-file, created via computer-aided design (CAD), was partly inserted into the root canal wall of the 3D-reconstructed tooth. By subtracting the K-file from the tooth, a tooth model with a root canal ledge was produced. The models were then 3D printed for a hands-on workshop. A seven-item Likert scale questionnaire was administered to 20 postgraduate students and 10 endodontists to assess the model's quality and training effectiveness. The feedback from both students and experts was positive, with no statistically significant differences found between the two groups (p > 0.05). This novel tooth model is expected to address the existing gap in endodontic education and provide benefits for dental practitioners in future applications.

The development of new turbomachinery designs requires numerous time-consuming and computationally intensive computational fluid dynamics (CFD) calculations. However, most of the generated high spatial resolution data remains unused at later development steps. That is also the case with automated optimization processes that use only a few integral values to determine objectives and constraints. Therefore the development of a data-driven AI model was initiated to ensure the potential of further use of the CFD data which is also used to train the AI model. The presented method subsequently provides a fast approximation of the 3D flow for new designs. In this paper, the structure of the developed AI model is presented and the approximation quality is analysed using a complex, state-of-the-art compressor test case. It is shown that the AI model can reproduce many characteristics of the 3D flow of new designs, and performance measures such as efficiency can be derived from these flow predictions. In addition, the complex test case revealed that greater design variation reduces the AI approximation quality which can lead to undesirable exploratory behaviour in an optimisation setup. Overall, the test case has shown promising results and has provided hints for further improvements of the AI model.

In the bioprinting process, controlling the motion of bioprinters involves a computer-aided design (CAD) model, converting that model into g-code, and transmitting the motion commands to the bioprinters. The g-code file contains information about the motion of the axes and can be generated using various software. However, a challenge arises when using g-code between different bioprinters. Therefore, the objective of this study was to propose a reliable method for analyzing the differences in 3D bioprinting devices by parameterizing a crucial variable for extrusion bioprinting: the E-value. Four bioprinters from three different manufacturers were used to investigate the extrusion behavior when subjected to the same E-value.

Abstract: In complex revision total hip arthroplasties, careful preoperative planning is crucial for the proper reconstruction of hip biomechanics. With conventional 2D radiographic images and computed tomography (CT) the 3D extension of the defect and the remaining bone stock may not be evaluated properly. 3D printed models can aid the surgeon in planning complex acetabular re-construction. The purpose of this study is to compare the accuracy of bony defect assessment in severe acetabular defects surgery with 3D printing planning as compared to conventional 2D ra-diographic planning and CT. Twenty-five patients with severe acetabular defects (Paprosky IIC and III) undergoing revision surgery were enrolled. Each patient had a 3D printed model of their femur and pelvis created based on CT scans. Clinical and radiographic assessments were conducted before and after surgery, with four key bone landmarks measured and compared between X-ray, CT, 3D models, and surgical reports. The findings revealed discrepancies in defect assessment between different imaging methods. X-rays and CT scans sometimes incorrectly identified affected areas, while the 3D models showed more accurate results. This study suggests that 3D printed models can significantly improve the preoperative evaluation of complex hip arthroplasty revisions, enabling surgeons to better select optimal surgical strategies.

Accurate forecasts of ocean waves energy can not only reduce costs for investment but it is also essential for management and operation of electrical power. This paper presents an innovative approach based on the Long Short Term Memory (LSTM) to predict the power generation of an economical wave energy converter named “Searaser”. The data for analyzing is provided by collecting the experimental data from another study and the exerted data from numerical simulation of searaser. The simulation is done with Flow-3D software which has high capability in analyzing the fluid solid interactions. The lack of relation between wind speed and output power in previous studies needs to be investigated in this field. Therefore, in this study the wind speed and output power are related with a LSTM method. Moreover, it can be inferred that the LSTM Network is able to predict power in terms of height more accurately and faster than the numerical solution in a field of predicting. The network output figures show a great agreement and the root mean square is 0.49 in the mean value related to the accuracy of LSTM method. Furthermore, the mathematical relation between the generated power and wave height was introduced by curve fitting of the power function to the result of LSTM method.

Three-dimensional (3D) printing technology, also known as additive manufacturing (AM), has emerged as an attractive state-of-the-art tool for precisely fabricating functional materials with complex geometries, championing several advancements in tissue engineering, regenerative medicine, and therapeutics. However, this technology has an untapped potential for biotechnological applications, such as sensor and biosensor development. By exploring these avenues, the scope of 3D printing technology can be expanded and pave the way for groundbreaking innovations in the biotechnology field. Indeed, new printing materials and printers would offer new possibilities for seamlessly incorporating biological functionalities within the growing 3D scaffolds. Herein, we review the extrusion-based 3D printing modalities emphasizing biosensor applications. We highlighted the application of natural, synthetic, and composite biomaterials as 3D-printed soft hydrogels. Emphasis was placed on the approach by which the sensing molecules were introduced during the fabrication process. Finally, the future perspective was provided.

Synthesis of heterodinuclear 3d transition metal complexes in which two metal ions are introduced in equivalent coordination sites of a ligand is quite uncommon. We have previously shown that the application of the cis-trans isomerization of the oxamido group was able to furnish such a possibility. In the present paper we demonstrate that this synthetic pathway, relying on the possibility of changing the conformation (cis vs trans) of the oxamido group, can be extended to other ligands. Although we have not been able to structurally characterize these complexes, EPR and magnetic data do confirm the efficiency of this reaction pathway. We also demonstrate that the cis-trans isomerization of the oxamido group is not due to a particular property of the ion involved in the reaction. In fact, isomerization is governed by the basicity of the reaction medium. According to the reaction condition, it is possible to favor or not this phenomenon, and to increase the accessibility to a larger number of novel genuine complexes. But the oxophilic character of the lanthanide ions impedes this isomerization in 3d-4f complexes. The very weak magnetic interactions observed in these Cu-Gd complexes can be explained thanks to spin polarization.

This paper focuses on leveraging a cutting-edge 3D state-space model for a holistic eco-friendly assessment in petrochemical operations. - By applying the ecological carrying capacity theory and the three-dimensional state-space model, this research aims to unleash the next frontier of sustainability in the petrochemical industry. - The proposed methodology will enable advanced and comprehensive eco efficiency evaluation in petrochemical operations. - Through the integration of the ecological carrying capacity theory and advanced modeling techniques, this research seeks to revolutionize sustainability assessments in the petrochemical sector. - The utilization of the cutting-edge 3D state-space model will provide a more advanced and accurate understanding of eco-friendly practices in petrochemical operations. This research presents a unique approach distinct from existing literature, which primarily examines business eco efficiency from behavioral motivation and strategic perspectives. In contrast, this paper introduces a novel three-dimensional state-space model to evaluate the ecological efficiency of petrochemical operations. By combining the ecological carrying index and state space, this model represents the ecological impact of petrochemical operations in a three-dimensional geometric space. It considers petrochemical operations as a significant factor exerting pressure on natural resources and the natural environment. In this three-dimensional state-space model, the three axes represent different dimensions of petrochemical operations. The first axis represents the economic status, which quantitatively describes the financial aspects of the operation. The second axis represents the utilization of resources, capturing the extent to which resources are consumed in the operation. The third axis focuses on the impact of the operation on the environment, allowing for a quantitative assessment of its ecological footprint. By incorporating these dimensions, the model aims to provide a comprehensive and quantitative description of the economic activities of petrochemical operations and their interactions with resources and the environment.The primary focus of this research is to apply the three-dimensional state-space model to calculate the ecological carrying capacity of petrochemical operations. By doing so, it aims to verify the feasibility and applicability of the model in determining the ecological efficiency of these operations. The research also aims to provide theoretical tools that can assist operations in making more informed ecological efficiency judgments. By utilizing this model, petrochemical operations will have a quantitative framework to assess and improve their environmental impact, thus fostering more sustainable practices. The findings of this research demonstrate that the implementation of this method can effectively identify issues related to resources, economy, and environment throughout the development of petrochemical operations. By identifying these problems, it provides managers with a solid foundation for making strategic decisions that promote sustainable development. With this valuable information at their disposal, managers can proactively address challenges, optimize resource utilization, and minimize environmental impacts, thus steering the petrochemical operations towards a more sustainable and responsible path.

Based on three-dimensional optical proximity correction (3D OPC), recent advancements in 3D lithography have enabled the high-fidelity customization of 3D micro-optical elements. However, micron-to-millimeter scale structures represented by Fresnel lens design bring more stringent requirements for 3D OPC, which poses significant challenges to the accuracy of models and the efficiency of algorithms. Thus, a lithographic model based on optical imaging and photo-chemical reaction curve is developed in this paper, and a sub-domain division method with a statistics principle is proposed to improve the efficiency and accuracy of 3D OPC. Both the simulation and the experimental results showed the superiority of the proposed 3D OPC method in the fabrication of the Fresnel lenses. The computation memory requirements of the 3D OPC are reduced to below 1 %, and the profile error of the fabricated Fresnel lens reduced 79.98%. Applying the Fresnel lenses to an imaging system, the average peak signal to noise ratio (PSNR) of the image increased by 18.92 %, and the average contrast of the image enhanced by 36 %. We believe the proposed 3D OPC method can be extended to the fabrication of vision-correcting ophthalmological lenses.

This study aimed to develop chitosan-based apigenin spray dried solid dispersion using 1:1,1:1.5,1:2 w/w ratios. The results of process yield and drug assay were found to be (87.5%, 94.2%, and 95.86%), (95.2 ±1.34%), (99.5 ±0.85%), and (97.6 ±2.42%), respectively, for AC1, AC2, and AC3. Flow properties indicate the free flow of powders. FTIR revealed compatibility among chitosan and apigenin, and DSC and XRD showed prepared solid dispersion was on a molecular level and available in amorphous. In contrast, SEM images reflect irregular block and near-spherical shape elongated particles in the selected AC2. The antimicrobial examination reflects that AC2 was more effective against Gram-positive, negative, and fungal strains. AC2 SDSDs has more anti-oxidant property compared to pure flavonoid (AGN). Anti-proliferative activity against A549 lung cancer cell lines showed better anti-cancer activity by AC2 SDSDs. The selected AC2 SDSD filled in a 3D shell pill and further characterized for 3D shell pill for dissolution profiles and stability studies. The product has sustained release and similar release profiles after three months of storage. The findings suggest that the AC2 SDSDs may be a promising candidate for further development as a 3D printed drug delivery system for treating multiple disease conditions using model flavonoid- apigenin.

Despite being small and simple structured in comparison to their victims, virus particles have the potential to harm severly and even kill highly developed species such as humans. To face upcoming virus pandemics, detailed quantitative biophysical understanding of intracellular virus replication mechanisms is inevitable. Unveiling the relationship of form and function might allow to determine putative attack points relevant for the systematic development of direct antiviral agents (DAA) and potent vaccines. Biophysical investigations of spatio-temporal dynamics of intracellular virus replication so far are rare. We are developing a framework to allow for fully spatio-temporal resolved virus replication dynamics simulations based on partial differential equations models (PDE) and evaluated with advanced numerical mathematical methods on leading supercomputers. This study presents an advanced highly nonlinear model of the genome replication cycle of a specific RNA virus, the Hepatitis C virus (HCV). The diffusion-reaction model mimics the interplay of the major components of the viral RNA (vRNA) cycle, namely non structural viral proteins (NSP), vRNA and a generic host factor. Technically, we couple surface PDEs (sufPDEs) on the 3D embedded 2D Endoplasmatic Reticulum (ER) manifold with PDEs in the 3D membranous web (MW) and cytosol volume. (The MWs are the replication factories growing on the ER induced by NSPs.) The sufPDE/PDE model is evaluated at realistic reconstructed cell geometries which are based on experimental data. The simulations couple the effects of NSPs which are restricted to the ER surface with effects appearing in the volume. The volume effects include the host factor supply from the cytosol and the MW dynamics. Special emphasis is put to the exchange of components between ER surface, MWs and cytosol volume. As the vRNA spatial properties are not fully understood so far in experiment, the model allows for vRNA both restricted to the ER and moving in the cytosol. The visualization of the simulation resembles a look into some sort of fully 3D resolved “in silico microscopes” to mirror and complement in vitro / in vivo experiments for the intracellular vRNA cycle dynamics. The output data are quantitatively consistent with experimental data and provoke advanced experimental studies to validate the model.

3D printing is playing an important role in cardiovascular disease by use of personalised models with replication of normal anatomy and pathology with high accuracy and reliability. While 3D printed heart and vascular models are shown to improve medical education, preoperative planning and simulation of cardiac procedures, and enhance communication with patients, 3D bioprinting however, represents a potential advancement of 3D printing technology by printing cellular or biological components, functional tissues and organs that can be used in a variety of applications in cardiovascular disease. Recent advances in bioprinting technology have shown the ability to support vascularisation of large scale constructs with enhanced biocompatibility and structural stability, thus creating opportunities to replace damaged tissues or organs. In this review, we provide an overview of the use of 3D bioprinting in cardiovascular disease with a focus on technologies and applications in cardiac tissues, vascular constructs and grafts, heart valves and myocardium. Limitations and future research directions are highlighted.

Tumor cells evolve in a complex and heterogeneous environment composed of different cell types and an extracellular matrix. Current 2D culture methods are very limited in their ability to mimic the cancer cell environment. In recent years, various 3D models of cancer cells have been developed, notably in the form of spheroids/organoids, using scaffold or cancer-on-chip devices. However, these models have the disadvantage of not being able to precisely control the organization of multiple cell types in complex architecture and are sometimes not very reproducible in their production, and this is especially true for spheroids. Three-dimensional bioprinting can produce complex, multi-cellular, and reproducible constructs in which the matrix composition and rigidity can be adapted locally or globally to the tumor model studied. For these reasons, 3D bioprinting seems to be the technique of choice to mimic the tumor microenvironment in vivo as closely as possible. In this review, we discuss different 3D-bioprinting technologies, including bioinks and crosslinkers that can be used for in vitro cancer models, and the techniques used to study cells grown in hydrogels; finally, we provide some applications of bioprinted cancer models.

Computer Vision using Deep Learning algorithms has served numerous human activity identification applications, particularly those linked to safety and security. However, despite the fact that autistic children are frequently exposed to danger as a result of their activities, many Computer Vision experts have shown little interest in their safety. High-grade autistic children frequently experience the Meltdown Crisis condition, characterized by hostile behaviors and loss of control. This study aims to introduce a monitoring system capable of predicting the Meltdown Crisis condition early and alerting the children’s parents or caregivers before entering more difficult settings. For this endeavor, the suggested system was constructed using a combination of a pre-trained Vision Transformer (ViT) model (Swin-3D-b) and a Residual Network (ResNet) architecture to extract robust features from video sequences in order to extract and learn the spatial and temporal features of the Stereotyped Motor Movements made by autistic children at the beginning of the Meltdown Crisis state, which is referred to as the Pre-Meltdown Crisis state. In order to attain a 92% recall and F1 Score, the final decisions made for data preparation, model construction, and training parameters were tweaked and established experimentally. The best loss value obtained was 0.08. The MeltdownCrisis dataset, which includes realistic scenarios of autistic children’s behaviors in the Pre-Meltdown Crisis state and Normal state the Normal state data being used as a negative class was utilized for evaluation.

This paper presents computer and color vision research focusing on human color perception in VR environments. A VR art gallery with digital twins of original artworks is created for this experiment. In this research, the field of colorimetry and the application of CMYK and RGB color models are applied. The interrelationships of the two colors models are applied to create a color modification of the VR art gallery environment using C# Script procedures. This color-edited VR environment works with a smooth change of color tone in a given time interval. At the same time, a sudden change in the color of the RGB environment is defined in this interval. This experiment aims to record a user's reaction embedded in a VR environment and the effect of color changes on human perception in a VR environment. The research uses lie detector sensors that record the physiological changes of the user embedded in VR. Five sensors are used to record the signal. An experiment on the influence of the user's color perception in a VR environment using lie detector sensors has never been conducted. This research defines the basic methodology for analyzing and evaluating the recorded signals from the lie detector. The presented text thus provides a basis for further research in the field of colors and human color vision in a VR environment and lays an objective basis for use in many scientific and commercial areas.

Manufacturing of facial epithesis is a complex technological process including several traditional stages of production, accompanied by aggravated psycho-emotional status of the patient. One of the main factors causing discomfort in patients with facial defects is the process of obtaining silicone impressions from the wound surface and the long waiting period for the final epithesis. Active development of digital technologies in medicine and dentistry helps specialists not only to automate most of the traditional stages of manufacturing of dento-mandibular and facial prostheses, but also improves the quality of life of patients by increasing the efficiency of services and reducing the production time of prosthetic structures. The application of digital technologies in the production of facial epithesis was difficult due to the lack of specialized 3D-software for modeling and material for further additive manufacturing of structures. The authors developed a unique technology for 3D modeling and additive manufacturing of facial epithesis, including a 3D CAD module and material for 3D printing. The primary objective was to fabricate immediate facial prostheses in the postoperative period in the shortest possible time until the final epithesis was fabricated.

The present study aimed to characterize the microstructure of a temporary 3D printing resin (Resilab Temp), evaluating the optical properties and mechanical behavior according to different post-processing curing times. For the analysis of the surface microstructure and establishment of the best printing pattern, samples in bar format following ISO 4049 (25 x 10 x 3 mm) were designed in CAD software (Rhinoceros 6.0), printed on the W3D printer (Wilcos), and light-cured in Anycubic Photon at different times (without curing, 16 minutes, 32 minutes, and 1 hour). For the structural characterization, analyses were carried out in FTIR (Fourier Transform Infrared Spectroscopy) and Scanning Electron Microscopy (SEM). The mechanical behavior of the resin was based on flexural strength tests and Knoop microhardness. Color and translucency analysis were performed with a spectrophotometer (VITA Easy Shade Advanced 4.0), which was evaluated following CIELab, using gray, black, and white backgrounds. All analyses were performed immediately after making the samples and repeated after thermal aging with 2 thousand cycles (5-55 °C). The results obtained were statistically analyzed with a significance level of 5%. FT-IR analysis showed about a 46% degree of conversion on the surface and 37% in the center of the resin sample. The flexural strength was higher for the groups polymerized for 32 min and 1h, while the Knoop microhardness did not show a statistical difference between the groups. Color and translucency analysis also did not show statistical differences between groups. According to all the analyses carried out in this study, for the evaluated material, the post-polymerization time of 1 hour can be suggested to improve the mechanical performance of 3D-printed devices.

In recent years, Additive Manufacturing (AM), commonly referred to as 3D printing, has garnered the attention of the scientific community due to its capacity to transform ordinary and traditional items into customized materials at an affordable cost, through various AM processes. Antimicrobial/antibiofilm 3D printed materials are one of the most trending research topics, owing to the growing concerns over the emergence of complex microbial structures called "biofilms" on various surfaces. The review provides an overview of the evolution of additive manufacturing (AM) technologies and their various derivatives, along with a brief description of their materials and applications. It also introduces how biofilms can represent an advantageous lifestyle for microbial populations. The primary objective of this research was to conduct a systematic review on the development of planctonic or biofilm forms of microorganisms on 3D printed materials. The article summarizes commonly studied microorganisms on these materials and presents their 3D printing process, materials, as well as the fields covered by each of the analyzed papers. To the best of our knowledge, this is the first all-inclusive systematic review that amalgamated research conducted in diverse fields to assess the development of biofilms on surfaces produced through three-dimensional printing. Most notably, this review presents a comprehensive account of sustainable approaches for producing antimicrobial materials through 3D printing. Additionally, we assess their advancements in various fields such as medicine, environment, agri-food, and other relevant sectors. The findings of our literature review can be used to recommend appropriate microorganisms, 3D printing materials, and technologies for academic and industrial research purposes focusing on the development of microbial biofilms on 3D printed surfaces. Furthermore, it highlights the potential of environmentally-friendly modified AM technologies to combat biofilms in clinical and non-clinical areas. Our goal with this review is to help readers gain a better understanding of fundamental concepts, inspire new researchers, and provide valuable insights for future empirical studies focused on eradicating biofilms from 3D printed materials.

The increasing request of digitized data among several fields, including the built environment and Cultural Heritage (CH) one points out the need of proficient ways to access, archive and share 3D data and related information among users. The sector of reality capture produces accurate and reliable products that can support building management and CH maintenance, at the price of heavy and resource-demanding data. An emerging solution to this problem is represented by the web platforms for 3D data management, that promise to relieve users from the costs of archive and hardware, providing effective visualization, access and sharing tools. The panorama of commercial web platforms is analyzed according to the Software as a Service business model and the features of some representative platforms are exposed. The paper discusses the main advantages in terms of diffused access and collaboration and the potential issues concerning the long-term archive and data persistence. The future perspectives of the web platform sector are promising as, according to the current development path, could be able to empower the built environment and CH sector with a diffused, systematic and aware use of 3D data.

Most common classifications for acetabular bone defects are based on radiographic two-dimension imaging, with low reliability and reproducibility. With the rise of modern processing techniques based on 3D modelling, methodologies for volumetric quantification of acetabular bone loss are available. Our study aims to describe a new methodology for quantitative assess-ment of acetabular defects, based on 3D modelling, focused on the surface analysis of the integrity of the main anatomical structures of the acetabulum represented by four corresponding sectors (posterior, superior, anterior, and medial). The defect entity is measured as the Area Increase Ra-tio (AIR) detected in all the sectors analyzed on three planes of view (frontal, sagittal and axial) compared to healthy hemipelvises. The analysis was performed on 3D-models from the CT-scan of six exemplary specimens with a unilateral pathological hemipelvis. AIR between the native and the pathological hemipelvis was calculated for each sector, for a total of 48 analysis (range, +0.93% - +171.35%). AIR of >50% were found in 22/48(45.8%) sectors and affected mostly the posterior, medial and superior sectors (20/22, 90.9%). Qualitative analysis showed consistency of the data with the morphological features of the defects. Further studies with larger samples are needed to validate the methodology and potentially develop a new classification scheme.

In the last 20 years, TADs have become one of the topics in orthodontic science, as it becomes one of the effective anchorages in moving teeth in a 3D movement to treat malocclusion and dental-alveolar orthopedic. Problems with the collusion of the roots of the teeth and trauma have hindered the use of these TADs; one of the solutions to keep TADs safe is a step-by-step innovation of procedure to make this anchorage concept using TAD safe. Making surgical guides for single-standing TADs is essential, and in practice, it is virtually possible with the advance of today's CAD/CAM and 3D printers. The content subject in the paper contains two parts: the consideration of why a surgical guide is necessary for the implantation of TADs and the making of the Surgical guide itself.

An approach employing ultrafast laser hybrid subtractive-additive microfabrication combining ablation, 3D nanolithography and welding is proposed for the realization of Lab-On-Chip (LOC) device. Single amplified Yb:KGW fs-pulsed laser source is shown to be suitable for fabricating microgrooves in glass slabs, polymerization of fine-meshes filter out of hybrid organic-inorganic photopolymer SZ2080 inside them, and, lastly, sealing the whole chip with cover glass into a single monolithic piece. The created microfluidic device proved its particle sorting function by separating 1 μm and 10 μm polystyrene spheres in a mixture. All together, this shows that fs-laser microfabrication technology is a flexible and versatile tool for the manufacturing of mesoscale multi-material LOC devices.

Digital twins are gaining in popularity for simulating complex natural and urban environments. In this context, accurate segmentation of objects within 3D urban environments is of crucial importance. The aim of this project is to develop a methodology for extracting buildings from textured 3D meshes. To this end, PicassoNet-II, a semantic segmentation architecture is employed. The methodology also incorporates Markov field-based contextual analysis to assess post-segmentation features. In addition, building instantiation is performed using cluster analysis algorithms. Training this model to fit various datasets requires a large amount of annotated data, both from Quebec City, Canada, and from simulated data. Experimental results show that the use of simulated data improves segmentation accuracy, and the DBScan algorithm proves effective in extracting isolated buildings. This project paves the way for improved applications in 3D urban modeling, offering opportunities in fields ranging from urban planning to resource management. The positive results with simulated data reinforce the impact of this research on improving digital models of our ever-changing urban environments.

The field of 3D model generation has become essential across various industries, including gaming, virtual and augmented reality (VR/AR), architecture, and medical imaging. Traditionally reliant on manual efforts, 3D content creation is now being transformed by deep generative models, enabling more efficient, scalable, and dynamic generation of complex shapes and environments. This survey provides a comprehensive review of key backbone architectures used for 3D generation, including autoencoders, variational autoencoders (VAEs), generative adversarial networks (GANs), autoregressive models, diffusion models, normalizing flows, attention-based models, CLIP-guided models, and procedural generation techniques. We explore each model’s role in 3D generation, highlighting their strengths—such as the precision of VAEs, the realism of GANs, the stability of diffusion models, and the scalability of procedural methods—alongside their limitations, such as training instability, high computational costs, and the difficulty in handling multi-modal data. Additionally, we discuss the increasing relevance of attention-enhanced models and the integration of text-based CLIP supervision for improved semantic alignment in 3D outputs. The survey concludes with an analysis of open challenges, including balancing efficiency with expressiveness, managing training complexity, and addressing dataset limitations. It also identifies future research directions, such as few-shot learning, hybrid architectures, and neural-symbolic approaches, which promise to advance the field by improving the generalization and versatility of 3D generation models. This paper aims to guide researchers and practitioners in navigating the evolving landscape of 3D generative methods and inspire new innovations in the creation of realistic, high-quality 3D content.

This paper aims to present the method of producing visual media for communicating the Asinara Island National Park plan. These products are landscape visualizations able to foster landscape preservation both from the point of view of the management of the landscape and of the citizen's involvement in the communication of the historical and environmental values of the landscape. Starting from landscape information gathering, the research has experimented with an operative method for processing different graphic representations from the same geographic database, calibrating the outputs to different audiences, their needs, objectives, and literacy skills. Three different types of products are presented: the first is a digital, dynamic and multisectoral decision-making GIS tool for park management. The second is a 3D model, aimed to the virtual fruition. The third is a map of the zoning park plan drawn to be easily readable to the non-expert public. This case study emerges as a replicable method to process the landscape information to make different visualization tools from a single geographic model, to meet the different requirements that arise from a complex landscape planning process.

New in vitro approaches for the assessment of their toxicity are crucial for creating better risk assessments given the growing use of nanoparticles (NPs) in the production of consumer goods. Humans will be exposed to nanoparticles through the inhalation route from contaminated aerosol. A promising method for evaluating the genotoxicity of NPs in vitro uses human airway epithelial cells. This study aimed to determine whether there were differences in morphology change of human bronchial/tracheal epithelial (HBTEC) cells responded to NPs in 2D and 3D spheroid models and to evaluate genotoxicity in 2D and 3D cultures after 24 hr exposure to TiO2-, Ag- and ZnO-NPs using the comet assay. Our 2D and 3D HBTEC cultures with TiO2-NPs did not show any statistically significant genotoxicity compared to controls for concentration points tested in vitro. HBTEC cells grown as 2D indicated that exposure to ZnO-NPs at low concentrations (10-50 ug/mL) for 24 hr did not cause any genotoxic effect but, at high concentrations, genotoxicity was observed. In contrast, treatment of 2D HBTEC with AgO-NPs led to an elevated in percentage of tail DNA damage from 50 ug/mL to 100 ug/mL, which was concentra-tion-dependent. Using 3D spheroid assays revealed a lower %tail length in ZnO- and AgO-NPs, thus exhibiting in vitro genotoxicity of NPs in this cell model. Spheroids (3D) rather than mono-layer cultures (2D) are believed to more precisely represent in vivo-like cell behavior when evaluating genotoxicity. Together, our findings demonstrate the genotoxic effects of NPs and point to the critical role that cell culture models play in the evaluation of toxicological risk.

In the production of green parts from powder, there is unavoidable slight deviation in the die filling, even when high-quality powders are used. The quantity of powder in the die varies and thus affects the weight of the compact. This filling variation results in variation of the pressing force, and thus influences the part geometry. The development of the DORST Netshape® System was conceived as an autonomous manufacturing system in order to compensate for these effects. Based on the Dorst Industry 4.0 innovations for part weight measuring immediately after pressing in combination with a laser dimension measuring system, this technology package attempts to reach enhanced precision and consistency in production. The paper presents results from various trials that show the capability of this new system, designed to improve the quality of pressed parts.

This paper presents the results of the investigation of composite sinters W-TiB2 which were used as an electrode in the process of electro-spark deposition (ESD) and the examination of the deposited layers. The scope of the study includes detailed characteristics of powder mixtures, composite sinters made using the spark plasma sintering method (SPS) and layers deposited in the electro-spark process. The ESD process, using the W+30 vol.% TiB2 electrode, was carried out using an automated device. The substrates were made of copper and aluminium. The topography analysis of the surfaces of the composite layer and the evaluation of their wear resistance properties are also presented. The analysis of the results of research showed the possibility to obtain, using the SPS method, composite materials of good quality, which can be used as electrodes in the ESD process. The obtained layers had increased wear resistance in relation to the substrate material.

We present progress in fast, high-resolution imaging, material classification, and fault detection using hyperspectral X-ray measurements. Classical X-ray CT approaches rely on data from many projection angles, resulting in long acquisition and reconstruction times. Additionally, conventional CT cannot distinguish between materials with similar densities. However, in additive manufacturing, the majority of materials used are known a priori. This knowledge allows to vastly reduce the data collected and increase the accuracy of fault detection. In this context, we propose an imaging method for non-destructive testing of materials based on the combination of spectral X-ray CT and discrete tomography. We explore the use of spectral X-ray attenuation models and measurements to recover the characteristic functions of materials in heterogeneous media with piece-wise uniform composition. We show by means of numerical simulation that using spectral measurements from a small number of angles, our approach can alleviate the typical deterioration of spatial resolution and the appearance of streaking artifacts.

Quality assurance has been one of the major challenges in laser-based additive manufacturing (AM) processes. This study proposes a novel process modeling methodology for layer-wise in-situ quality monitoring based on image series analysis. An image-based autoregressive (AR) model has been proposed based on the image registration function between consecutively observed thermal images. Image registration is used to extract melt pool location and orientation change between consecutive images, which contains sensing stability information. Subsequently, a Gaussian process model is used to characterize the spatial correlation within the error matrix. Finally, the extracted features from the aforementioned processes are jointly used for layer-wise quality monitoring. A case study of a thin wall fabrication by a Directed Laser Deposition (DLD) process is used to demonstrate the effectiveness of the proposed methodology.

Additive Manufacturing (AM) simplifies the fabrication of complex geometries. Its scope has rapidly expanded from the fabrication of pre-production visualization models to the manufacturing of end use parts driving the need for better part quality assurance in the additively manufactured parts. Machine learning (ML) is one of the promising techniques that can be used to achieve this goal. Current research in this field includes the use of supervised and unsupervised ML algorithms for quality control and prediction of mechanical properties of AM parts. This paper explores the applications of supervised learning algorithms - Support Vector Machines and Random Forests. Support vector machines provide high accuracy in classifying the data and is used to decide whether the final parts have the desired properties. Random Forests consist of an ensemble of decision trees capable of both classification and regression. This paper reviews the implementation of both algorithms and analyzes the research carried out on their applications in AM.

OBJECTIVE: Although 3D-printed anatomic models are not new to medicine, the high costs and lengthy production times entailed have limited their application. Our goal was developing a new and less costly 3D modeling method to depict organ-tumor relations at faster printing speeds. METHODS: We have devised a method of 3D modeling using DICOM images. Coordinates are extracted at a specified interval, connecting them to create mesh-work replicas. Adjacent constructs are depicted by density variations, showing anatomic targets (ie, tumors) in contrasting color. RESULTS: An array of organ solid-tumor models were printed via Fused Deposition Modeling 3D printer at significantly less cost ($0.05/cm3) and time expenditure (1.73 min/cm3; both, p<.001). Printed models helped promote visual appreciation of organ-tumor anatomy and adjacent tissues. Our mesh-work 3D thyroidal prototype reproduced glangular size/contour and tumor location, readily approximating the surgical specimen. CONCLUSIONS: This newly devised mesh-type 3D printing method may facilitate anatomic modeling for personalized care and improve patient awareness during informed surgical consent.

3D printing facilitates the straightforward construction of microchannels with complex three-dimensional architectures. Here, we demonstrate 3D-printed modular mixing components that operate on the basis of splitting and recombining fluid streams to decrease interstream diffusion length. These are compared to helical mixers that operate on the principle of chaotic advection.

Solar3D is an open-source software application designed to interactively calculate solar irradiation at three-dimensional (3D) surfaces in a virtual environment constructed with combinations of 3D city models, digital elevation models (DEMs), digital surface models (DSMs) and feature layers. The GRASS GIS r.sun solar radiation model computes solar irradiation based on two-dimensional (2D) raster maps for given day, latitude, surface and atmospheric conditions. With the increasing availability of 3D city models and demand for solar energy, there is an urgent need for better tools to computes solar radiation directly with 3D city models. Solar3D extends GRASS GIS r.sun from 2D to 3D by feeding the model with input, including surface slope, aspect and time-resolved shading, that is derived directly from the 3D scene using computer graphics techniques. To summarize, Solar3D offers several new features which, as a whole, distinguish itself from existing 3D solar irradiation tools: (1) the ability to consume massive heterogeneous 3D city models, including massive 3D city models such as oblique airborne photogrammetry-based 3D city models (OAP3Ds or integrated meshes); (2) the ability to perform near real-time pointwise calculation for duration from daily to annual; (3) the ability to integrate and interactively explore large-scale heterogeneous geospatial data. (4) the ability to calculate solar irradiation at arbitrary surface positions including at rooftops, facades and the ground. Solar3D is publicly available at https://github.com/jian9695/Solar3D.

3D printing is described as the third industrial revolution: its impact is global in industry and progresses every day in society. It presents a huge potential for ecology and evolution, sciences with a long tradition of inventing and creating objects for research, education and outreach. Its general principle as an additive manufacturing technique is relatively easy to understand: objects are created by adding material layers on top of each other. Although this may seem very straightforward on paper, it is much harder in the real world. Specific knowledge is indeed needed to successfully turn an idea into a real object, because of technical choices and limitations at each step of the implementation. This article aims at helping scientists to jump in the 3D printing revolution, by offering a hands-on guide to current 3D printing technology. We first give a brief overview of uses of 3D printing in ecology and evolution, then review the whole process of object creation, split into three steps: (1) obtaining the digital 3D model of the object of interest, (2) choosing the 3D printing technology and material best adapted to the requirements of its intended use, (3) pre- and post-processing the 3D object. We compare the main technologies available and their pros and cons according to the features and the use of the object to be printed. We give specific and key details in appendices, based on examples in ecology and evolution.

We introduce optically clear and resilient free-form micro-optical of pure (non-photosensitized) organic-inorganic SZ2080 material made by femtosecond 3D laser lithography (3DLL). This is advantageous for rapid printing of 3D micro-/nanooptics, including their integration directly onto optical fibers. A systematic study on the fabrication peculiarities and quality of resultant structures is performed. Comparison of microlenses’ resiliency to CW and femtosecond pulsed exposure is determined. Experimental results prove that pure SZ2080 is ∼3 fold more resistant to high irradiance as compared with a standard photo-sensitized material and can sustain up to 1.91 GW/cm² intensity. 3DLL is a promising manufacturing approach for high-intensity micro-optics for emerging fields in astro-photonics and atto-second pulse generation. Additionally, pyrolysis is employed to shrink structures up to 40% by removing organic SZ2080 constituents. This opens a promising route towards downscaling photonic lattices and creation of mechanically robust glass-ceramic structures.

A novel approach for the long-term medical treatment of the inner ear is the diffusion of drugs through the round window membrane from a patient-individualized, drug-eluting implant, which is inserted in the middle ear. In this study, drug-loaded (10 wt% Dexamethasone) guinea pig round window niche implants (GP-RNIs, ~1.30 mm x 0.95 mm x 0.60 mm) were manufactured with high precision via micro injection molding (µIM, Tmold = 160 °C, crosslinking time of 120 s). The medical grade silicone elastomer MED-4244 (NuSil Technology LLC, Radnor, PA, USA) was used. Molds for µIM were 3D printed from a commercially available resin PlasGRAY V2 (Asiga, Alexandria, Australia, TG = 84 °C) via a high-resolution DLP process (xy-resolution of 32 µm, z-resolution of 10 µm, 3D printing time of about 6 h). Drug release, biocompatibility, and bio-efficacy of the GP-RNIs were investigated in vitro. GP-RNIs could be successfully produced. Wear of the molds due to thermal stress was observed. However, the molds are suitable for single use in the µIM process. About 10% of the drug load (8.2 ± 0.6 µg) was released after 6 weeks (medium: isotonic saline). The implants showed high biocompatibility over a time of 28 days (lowest cell viability ~80%). Moreover, we found anti-inflammatory effects over a time of 28 days in a TNF-α-reduction test. These results are promising for the development of long-term drug-releasing implants for human inner ear therapy.

Background. Currently, most of the research in breast cancer has been carried out in conventional two-dimensional (2D) cell culture due to its practical benefits, however, the three-dimensional (3D) cell culture is becoming the model of choice in cancer research because it allows cell-cell and cell-extracellular matrix (ECM) interactions, mimicking the native microenvironment of tumors in vivo. Methods. in this work, we evaluated the effect of 3D cell organization on the expression pattern of miRNAs (by Small-RNAseq) and mRNAs (by microarrays) in the breast cancer SKBR3 cell line and analyzed the biological processes and signaling pathways regulated by the differ-entially expressed protein-coding genes (DE-mRNAs) and miRNAs (DE-microRNAs) found in the organoids. Results. We obtained well-defined cell-aggregated organoids with a grape cluster-like morphology with a size up to 9.2×105 μm3. The transcriptomic assays showed that cell growth in organoids significantly affected (all p < 0.01) the gene expression patterns of both, miRNAs and mRNAs, finding 20 upregulated and 19 downregulated DE-microRNAs, as well as 49 upregulated and 123 downregulated DE-mRNAs. In silico analysis showed that a subset of 11 upregulated DE-microRNAs target 70 downregulated DE-mRNAs. These genes are involved in 150 gene on-tology (GO) biological processes such as regulation of cell morphogenesis, regulation of cell shape, regulation of canonical Wnt signaling pathway, morphogenesis of epithelium, regulation of cy-toskeleton organization, as well as in the MAPK and AGE-RAGE signaling KEGG-pathways. In-terestingly, hsa-mir-122-5p (Fold Change (FC)=15.4), hsa-mir-369-3p (FC=11.4), and hsa-mir-10b-5p (FC=20.1) regulated up to the 81 % of the 70 downregulated DE-mRNAs. Conclu-sion, the organotypic 3D cell-organization architecture of breast cancer SKBR3 cells impacts the expression pattern of miRNAs-mRNAs network mainly through overexpression of hsa-mir-122-5p, hsa-mir-369-3p, and hsa-mir-10b-5p. All these findings suggest that the interaction between cell-cell and cell-ECM as well as the change in the culture architecture impacts gene ex-pression, and therefore, support the pertinence of migrating breast cancer research from conven-tional cultures to 3D models.

Based on the minimum conduction band edge caused by the minimum channel potential resulting from the quasi-3D scaling theory and the 3D density of state (DOS) accompanied by the Fermi-Dirac distribution function on the source and drain sides, a unified semiconductor-device-physics-based ballistic model is developed for the threshold voltage of modern multiple-gate (MG) transistors, including FinFET, W-gate MOSFET, and Nanosheet (NS) MOSFET. It is shown that the thin silicon, thin gate oxide, and high work function will alleviate the ballistic effects and resist the threshold voltage degradation. Besides, as the device dimension is further reduced to give rise to the 2D/1D DOS, the lowest conduction band edge is hence increased to resist the threshold voltage degradation. The nanosheet MOSFET exhibits the largest threshold voltage among the three transistors due to the smallest minimum conduction band edge caused by the quasi-3D minimum channel potential. Compared to P-type MOSFET (P-FET), the N-FET shows more threshold voltage because the electron has a more effective mass than the hole

Path planning in 3D environment is a fundamental research area for robots and autonomous vehicles. Based on the principle ``the shortest path consists of tangents'', RimJump* is proposed as a tangent-based path planning method suitable for finding the shortest path (both off-ground and on-ground) in 3D space (e.g., octomap and point cloud) for mobile platform to follow. RimJump* searches the tangent graph in the form of a path tree and considers the geometrical properties of the locally shortest path. Therefore, the method can provide all of the locally shortest paths that connect the starting point and the target, including the globally shortest path. And the time cost of RimJump* is insensitive to map scale increases in comparison to methods that search the whole passable space rather than the surface of the obstacle, e.g., Dijkstra and A*. In the Results, RimJump* is compared with other methods in terms of path length and time cost.

Background: Melatonin is a potent mitochondrial, cytoprotective and antioxidant molecule with potentially strong anti-aging properties. Topical melatonin has shown to improve the clinical signs of skin aging. Melatosphere™ is a new lipid-based delivery system able to improve stability and skin penetration of melatonin when used in topical formulations. No clinical studies, using objective instrumental data, are available so far regarding the positive effect of Melatosphere™ in improving wrinkles in women with mild-to-moderate skin aging. Study Aim: We evaluate, in an open prospective, evaluator-blinded trial, the effects on skin texture of 2 months treatment with a Melatosphere™ based cream. Subjects and Methods: 15 women aged >45 years with mild to moderate facial skin aging (Glogau score ≥2) participated in the trial, after their informed consent. An ANTERA 3D computer-assisted skin analysis evaluation for the assessment of coarse and fine wrinkles of the periorbital area and melanin content was performed at baseline and after two months of treatment. An evaluator-blinded Investigator Global assessment of skin elastosis, roughness, level of dyscromia, skin dryness and presence of actinic damage was also performed at the same time points using a 4-grade score from 0 (no sign) to 3 (severe sign). Results: At baseline the mean (SD) IGA score was 8.2(1.0). After 2 months the IGA score significantly decrease to 4.2(1.4) (49% reduction) (P=0.0007). ANTERA 3D evaluations showed a significant reduction in skin coarse and fine wrinkles volume in the target area of -31% and -18%, respectively. Melanin content was reduced significantly by -17%. Conclusion: Topical melatonin carried in Melatosphere improves in the short-term signs of skin aging evaluated clinically and by ANTERA 3D device in women with mild to moderate skin aging.

We demonstrated a new approach to the production of three-dimensional-coated patterns using liquid route. Metallic perovskite oxides were coated onto three-dimensional (3D) microstructured substrates with different aspect ratios. The success of the method relies on the solution viscosity monitored by adding viscous liquid. The process of oxide thin films consists in three steps: preparing the precursor solution, coating the solution by spin-coating process onto three-dimensional-Si substrates and post-annealing. The chemical solution 3D-coating is conformal.

Customized wrist splints, particularly for upper extremity orthoses like wrist support braces, are commonly used across numerous clinical scenarios. However, the traditional process for producing personalized wrist splints is largely manual and highly dependent on the expertise of orthopedic specialists. This experience-based approach often leads to suboptimal outcomes, necessitating further refinement of the designs. Recent advancements in Additive Manufacturing (AM) have brought significant innovation to various industries, including orthopedics. This study aims to present a comprehensive methodology that integrates advanced design tools ,like 3D Scanning, with digital manufacturing techniques to produce tailored wrist splints. The produced hand brace aims to offer enhanced mechanical performance and comfort by precisely fitting an individual’s anatomy while minimizing material usage and weight. To achieve optimal design efficiency, the study explores the application of a Topology Optimization (TO) approach for design, while the manufacturing process utilizes Fused Deposition Modeling (FDM), an evolving technology within the Additive Manufacturing (AM) sector.

Prior to clinical trials, preclinical testing of oncology drug candidates is performed by evaluating drug candidates with in vitro and in vivo platforms. For in vivo testing, animal models are used to evaluate the toxicity and efficacy of drug candidates. However, animal models often display poor translational results as many drugs that pass preclinical testing fail when tested in humans, with oncology drugs exhibiting especially poor acceptance rates. The FDA Modernization Act 2.0 promotes alternative preclinical testing techniques, presenting the opportunity to use higher complexity in vitro models as an alternative to in vivo testing, including 3D cell culture models. 3D tissue cultures address many of the shortcomings of 2D cultures by more closely replicating the tumour microenvironment through a combination of realistic drug diffusion, paracrine signaling, cellular phenotype, and vascularization that can better mimic native human tissue. This review will discuss the common forms of 3D cell culture, including cell spheroids, organoids, organs-on-a-chip, and 3D bioprinted tissues. Their advantages and limitations will be presented, aiming to discuss the use of these 3D models to accurately represent human tissue and as an alternative to animal testing. The use of 3D culture platforms for preclinical drug development is expected to accelerate as these platforms continue to improve in complexity, reliability, and translational predictivity.

Transparent and high-hardness materials have become the object of wide interest. Most notably, it concerns technical glasses and crystals. A notable example is a sapphire – one of the most rigid materials having impressive mechanical stability and good optical properties. Nonetheless, using this material for 3D micro-fabrication is not straightforward due to its brittle nature. On the microscale, selective laser etching (SLE) technology is an appropriate approach for such media. Therefore, we present our research on c-cut crystalline sapphire microprocessing by using femtosecond radiation-induced SLE. Here we demonstrate a comparison between different wavelength radiation (1030 nm, 515 nm, 343 nm) usage for modification inscription and various etchants (Hydrofloridic acid, Sodium Hydroxide, Potassium Hydroxide and Sulphuric and Phosphoric acid mixture) comparison. We show that regular SLE etchants such as Hydrofluoric acid or Potassium Hydroxide are unsuitable materials for selective sapphire laser etching. Meanwhile, a 78% sulphuric and 22% phosphoric acid mixture at 270°C temperature is a good alternative for this process. We present the changes in the material after the separate processing steps. Finally, a protocol for advanced sapphire structure formation and a few exemplary structures are presented.

This paper analyses and evaluate the precision and the accuracy the capability of low-cost terrestrial photogrammetry by using many digital cameras to construct a 3D model of an object. To obtain the goal, a building façade has imaged by two inexpensive digital cameras such as Canon and Pentax camera. Bundle adjustment and image processing calculated by using Agisoft PhotScan software. Several factors will be included during this study, different cameras, and control points. Many photogrammetric point clouds will be generated. Their accuracy will be compared with some natural control points which collected by the laser total station of the same building. The cloud to cloud distance will be computed for different comparison 3D models to investigate different variables. The practical field experiment showed a spatial positioning reported by the investigated technique was between 2-4cm in the 3D coordinates of a façade. This accuracy is optimistic since the captured images were processed without any control points.

Fabrication of a true-3D inorganic ceramic with resolution down to nanoscale using sol-gel resist precursor is demonstrated. The method has an unrestricted free-form capability, control of the fill-factor, and high fabrication throughput. A systematic study of the proposed approach based on ultrafast laser 3D lithography of organic-inorganic hybrid sol-gel resin followed by a heat treatment enabled formation of inorganic amorphous and crystalline composites guided by the composition of the initial resin. The achieved resolution of 100 nm was obtained for 3D patterns of complex free-form architectures. Fabrication throughput of 50×10³ voxels/s is achieved; voxel - a single volume element was recorded by a single pulse exposure. After a subsequent thermal treatment, ceramic phase was formed depending on the temperature and duration of the heat treatment as validated by Raman micro-spectroscopy. The X-ray diffraction (XRD) revealed a gradual emergence of the crystalline phases at higher temperatures with a signature of cristobalite SiO₂, a high-temperature polymorph. Also, the tetragonal ZrO₂ phase known for its high fracture strength was observed. This 3D nano-sintering technique is scalable from nano- to millimeter dimensions and opens a conceptually novel route for optical 3D nano-printing of various crystalline inorganic materials defined by an initial composition for diverse applications for microdevices in harsh physical and chemical environments and high temperatures.

3D printing has significantly transformed the design and manufacture of robotic prostheses, making these devices more accessible, customized, and functional. This paper examines the historical evolution of prosthetic technology, tracing its development from rudimentary mechanical devices to the integration of advanced technologies, such as 3D printing. This innovation has enabled the production of prostheses at lower costs while enhancing their adaptability and performance. The review highlights how 3D printing has driven a disruptive shift in prosthetic customization, and how emerging technologies—including smart materials and artificial intelligence—have expanded the capabilities of prosthetic devices, offering more adaptive and natural movement. However, challenges persist, particularly regarding the need for standardization and infrastructure expansion to ensure equitable access to these technologies. Future research into novel materials and manufacturing techniques holds the potential to improve further the functionality, affordability, and accessibility of prosthetic devices. In conclusion, while 3D printing has marked a significant milestone in the evolution of robotic prosthetics, overcoming existing challenges is essential to realize its global impact and benefits fully.

While cycling presents environmental benefits and promotes a healthy lifestyle, the risks associated with overtaking maneuvers by motorized vehicles pose significant hindrances for many potential cyclists. Large-scale analysis of overtaking maneuvers could inform traffic researches and city planners on how to reduce these risks by better understanding these maneuvers. Drawing from the fields of sensor-based cycling research and of LiDAR-based traffic data sets, this paper provides a step towards addressing these safety concerns by introducing the Salzburg Bicycle 3d (SaBi3d) data set, consisting of LiDAR point clouds capturing car-to-bicycle overtaking maneuvers. The data set, collected using a LiDAR-equipped bicycle, facilitates detailed analysis of a large quantity of overtaking maneuvers without the need for manual annotation through enabling automatic labeling by a neural network. Additionally, a benchmark result for 3d object detection using a competitive neural network is provided as a baseline for future research. The SaBi3d data set is structured identically to the nuScenes data set, and therefore offers compatibility with numerous existing object detection systems. This work provides valuable resources for future researchers to better understand cycling infrastructure and mitigate risks, thus promoting cycling as a viable mode of transportation.

3D cell cultures have improved the evaluation of drugs for cancer therapy, due to their high similarity to solid tumors. In melanoma, autophagy appears to show a dual role depending on the progression of the disease. p62 protein has been proposed for the evaluation of autophagic flux since its expression is an indicator of the state of autophagy. Pentoxifylline (PTX) and Norcantharidin (NCTD) are drugs that have been shown to have anticancer effects in various types of cancer. In this work, B16F1 mouse melanoma cell line was used, from which two-dimensional (2D) monolayer cultures and three-dimensional (3D) organoids were carried out using the hanging drop technique. The expression of p62 was determined by western blot and immunofluorescences. Our results indicate that pentoxifylline reduces p62 expression in both types of culture. While Norcantharidin increases its expression in 3D cultures at 24 h. Therefore, these drugs could have a potential therapeutic use for the regulation of autophagy in melanoma, depending on the state of evolution of the disease.

Additive manufacturing, commonly referred to as 3D printing, is an exciting and versatile manufacturing technology that is gaining traction and interest in both academic and industrial settings. Polymeric materials are essential components in a majority of the “inks” used across the various 3D printing technologies. As the environmental ramifications of sole or primary reliance on petrochemicals as a resource for industrial polymers continue to manifest themselves at a global scale, a transition to more sustainable bioderived alternatives could offer solutions. In particular, cellulose is promising due to its global abundance, biodegradability, excellent thermal and mechanical properties, and ability to be chemically modified to suit various applications. Thus far, cellulose has typically been incorporated in additive manufacturing applications as a substrate, filler, or reinforcement for other materials. However, due to its versatility and desirable properties, the exploration of all-cellulose 3D printing materials and associated methodologies is increasing. This review will discuss the progress and status of all-cellulose 3D printing approaches, associated challenges, and their potential as a key player in a more sustainable industrial future.

This research presents the creation of a Virtual Reality experience for the Balzi Rossi museum, commemorating the centenary of Prince Albert I Grimaldi's archaeological work at the site. The project, a collaboration between the University of Genoa's 3D Lab Factory, Eurodrone, and the Balzi Rossi archaeological museum, aims to preserve and convey the site's heritage through advanced VR technology. Initially employing Unreal Engine 4, the team used photogrammetry for 3D reconstruction of the "Caviglione" and "Florestano" caves, notable for their ancient rock engravings. This first VR model, despite hardware limitations, provided an interactive exploration of the site. The subsequent development phase utilized Unreal Engine 5, incorporating Nanite technology for enhanced visual fidelity. This advancement resulted in a more detailed and immersive VR experience, presenting the Balzi Rossi cliff across different historical periods, including the Würm glaciation. Key to this phase was optimizing the VR experience for performance, focusing on stable frame rates and minimizing motion sickness, and integrating a multi-lingual interface for broader accessibility. Since November 2023, the VR setup at the Balzi Rossi Museum has been an educational and interactive feature, enabling visitors to explore the site's history virtually. This research demonstrates the potential of VR in cultural heritage preservation and education, providing a foundation for future technological improvements in the field.