Concerns about China’s air quality, and its impact on the important tourism industry have been on the debate in recent years. This article aims to investigate the potential effect of air pollution on direct economic impact of tourism, using the case of Beijing and Shanghai. The results indicate that air pollution negatively affects China's inbound tourism, resulting in huge loss of tourist arrivals and receipts, and Beijing suffers a greater loss in comparison with Shanghai, its loss in tourist number amounts to 1569,700 persons, equal to CNY 10264.268 million in tourism receipts, and the GDP losses ranges from CNY 20528.536 to 41057.072 across major source countries. This study provides a quantification of the impact helpful to generate a social awareness of air pollution detrimental impacts on inbound tourism and hence the economy.

In this study, we test the performance of a compact gas chromatograph with photoionization detector (GC-PID) and optimize the configuration to detect ambient (sub-ppb) levels of benzene, toluene, ethylbenzene, and xylene isomers (BTEX). The GC-PID system was designed to serve as a relatively inexpensive (~$10k) and field-deployable air toxic screening tool alternative to conventional benchtop GCs. The instrument uses ambient air as a carrier gas, and consists of a Tenax-GR trap preconcentrator, a gas sample valve, two capillary columns, and a photoionization detector (PID) with a small footprint and low power requirement. The performance of the GC-PID has been evaluated in terms of system linearity and sensitivity in field conditions. The BTEX-GC system demonstrated the capacity to detect BTEX at levels as high as 500 ppb with a linear calibration range of 0-100 ppb. A detection limit lower than 1 ppb was found for all BTEX compounds with a sampling volume of 1 L. No significant drift in the instrument was observed. A time-varying calibration technique was established that requires minimal equipment for field operations and optimizes the sampling procedure for field measurements. With an analysis time of less than 15 minutes, the compact GC-PID is ideal for field deployment of background and polluted atmospheres for near-real time measurements of BTEX. The results highlight the application of the compact and portable GC-PID for community monitoring and screening of air toxics.

Market air quality is very important to the economic lives of the people which is rarely researched, however, market activities particularly pedestrian traffic releases particulates which is detrimental to the health of the users and stakeholders. Thermo scientific MIE pDR-1500 particulate was used to monitor the quality of air within the market for eight (8) weeks, air pollutant of concern is PM2.5. ten (10) sample points were located in the market which covers ten (10) sample points for pedestrian traffic to represent the entire market environment spectrum. The analysis of PM2.5 measured daily during dry and wet season shows a clear seasonal variation of this particular pollutant as elevated concentration was measured during the dry season than the wet season. The assessment of PM2.5 concentration shows exceedances of the standards stated by WHO and NAAQS during the dry season which ranges from 47.9 μg/m3- 231.88 μg/m3 in the morning and 65.17 μg/m3- 1806.33 μg/m3 in the afternoon. From the findings, pedestrian traffic contributes immensely to air pollution in an open market, with this elevated concentration, prolonged exposure is highly detrimental to health. This study creates awareness to the pedestrians in an open market about air pollution and informs policy changes.

In the past two decades, acoustic metamaterials have garnered much attention owing to their unique functional characteristics, which is difficult to be found in naturally available materials. The acoustic metamaterials have demonstrated to exhibit excellent acoustical characteristics that paved a new pathway for researchers to develop effective solutions for a wide variety of multifunctional applications such as low-frequency sound attenuation, sound wave manipulation, energy harvesting, acoustic focusing, acoustic cloaking, biomedical acoustics, and topological acoustics. This review provides an update on the acoustic metamaterials' recent progress for simultaneous sound attenuation and air ventilation performances. Several variants of acoustic metamaterials, such as locally resonant structures, space-coiling, holey and labyrinthine metamaterials, and Fano resonant materials, are discussed briefly. Finally, the current challenges and future outlook in this emerging field is discussed as well.

The literature, aimed at understanding the income-price elasticity of air passenger demand, bases its analysis on airport movement. The diversity of studies regarding the casualty between air transportation and economic growth are examples. Some studies covering this link, estimate the income-price relationship with the demand considering international traffic. Considering a domestic setting, where this traffic is significant in Brazil, studies related to remote regions are scarce, and the existing ones focus on governmental policies and subsidies. In addition, empirical studies on the theme consenter themselves in developed regions, such as Europe, North America, and Australia. For Brazil, where we find the Amazon region, there are no empirical researches. This paper analyses the price-income elasticity of the demand regarding domestic passengers in air links from remote cities of the Brazilian Amazon. This study uses panel data regression analysis method on a database of domestic scheduled flights of Brazil´s National Civil Aviation Agency. The results show that air passengers involving remote region flights present a lower sensitiveness regarding local income and airline´s price variations than those in flights among capitals. The higher difference is in income-elasticity of the remote city of origin, which is lower than that of the air traffic among capitals.

Population concentration in cities brings new risks as an increase in pollution, which causes urban health problems. In order to address this problem, traffic reduction measures are being implemented, as pedestrianization areas and the definition of Low Emissions Zones (LEZ). When the effectiveness of these types of measures is in doubt, smart city tools provide data that can be used to scientifically asses their impact. This article analyzes the situation of Madrid Central (Spain), a LEZ subject to controversy. We apply statistical and regression analyses to evaluate the effectiveness of this measure to reduce air pollution and outdoor noise. According to the results, this LEZ was able to significantly reduce NO$_2$, PM$_{2.5}$, and PM$_{10}$ concentration locally, having the same positive impact in the rest of the city. In terms of noise, this measure is able to mitigate background noise levels generated by the road traffic.

Background: Covid-19 was first reported in Wuhan, China in Dec 2019. Since then, it has been transmitted rapidly in China and the rest of the world. While Covid-19 transmission rate has been declining in China, it is increasing exponentially in Europe and America. Although there are numerous studies examining Covid-19 infection, including an archived paper looking into the meteorological effect, the role of outdoor air pollution has yet to be explored rigorously. It has been shown that air pollution will weaken the immune system, and increase the rate of respiratory virus infection. We postulate that outdoor air pollution concentrations will have a negative effect on Covid-19 infections in China, whilst lockdowns, characterized by strong social distancing and home isolation measures, will help to moderate such negative effect. Methods: We will collect the number of daily confirmed Covid-19 cases in 31 provincial capital cities in China during the period of 1 Dec 2019 to 20 Mar 2020 (from a popular Chinese online platform which aggregates all cases reported by the Chinese national/provincial health authorities). We will also collect daily air pollution and meteorology data at the city-level (from the Chinese National Environmental Monitoring Center and the US National Climatic Data Center), daily inter-city migration flows and intra-city movements (from Baidu). City-level demographics including age distribution and gender, education, and median household income can be obtained from the statistical yearbooks. City-level co-morbidity indicators including rates of chronic disease and co-infection can be obtained from related research articles. A regression model is developed to model the relationship between the infection rate of Covid-19 (number of confirmed cases/population at the city level) and outdoor air pollution at the city level, after taking into account confounding factors such as meteorology, inter- and intra-city movements, demographics, and co-morbidity and co-infection rates. In particular, we shall study how air pollution affects infection rates across different cities, including Wuhan. Our model will also study air pollution would affect infection rates in Wuhan before and after the lockdown. Expected findings: We expect there be a correlation between Covid-19 infection rate and outdoor air pollution. We also expect that reduced intra-city movement after the lockdowns in Wuhan and the rest of China will play an important role in reducing the infection rate. Interpretation: Infection rate is growing exponentially in major cities worldwide. We expect Covid-19 infection rate is related to the air pollution concentration, and is strongly dependent on inter- and intra-city movements. To reduce the infection rate, the international community may deploy effective air pollution reduction plans and social distancing policies.

Two isotropic pitches were prepared by air blowing and nitrogen distillation method using ethylene tar (ET) as a raw material. And correspondent carbon fibers were obtained through conventional melt spinning, stabilization and carbonization. The structures and properties of resultant pitches and fibers were characterized and their differences were discussed in this work. The results showed that introduction of the oxygen by air blowing method could quickly increase the yield and softening point of pitch. Moreover, the air blown pitch (ABP) composed of linear methylene chains of aromatic molecules while the nitrogen distilled pitch (NDP) mainly contained polycondensed aromatic rings, which was due to the oxygen containing functional groups existed in ABP could impede order stack of pitch molecules and form methylene bridge structure, instead of aromatic condensed structure like NDP. Meanwhile, the spinnability of ABP was not decreased even containing 2.31 wt% oxygen. In contrast, ABP had narrower molecular weight distribution, which contributed to better stabilization properties and higher tensile strength of carbon fiber. The tensile strength of carbon fibers from ABP was reached to 860 MPa with fiber diameter of about 10 μm, which was higher than that of NDP-derived carbon fibers of 640 MPa.

Ultraviolet (UV) light with a wavelength of 254 nm has proven to be effective at inactivating microorganisms, and thus has been increasingly employed as a method of disinfection for indoor environments. Solar UV wavelengths (300 to 400 nm) are known to initiate the formation of secondary organic aerosol (SOA) particles from photo-oxidation of volatile organic compounds in the atmosphere, but germicidal wavelengths have not been extensively studied for indoor environments. In this work, toluene was exposed to 254 nm UV light in a laboratory photoreactor, with varying conditions of the air, the duration of UV exposure, and the duration of post-UV time. The number of particles formed in the fine particulate matter (PM2.5) size range was measured, and significant levels of particle formation were observed for UV exposure periods of as short as 5 minutes. The particle formation ranged from 2.4x10⁶ particles/m³ for 5 minutes of UV exposure, to 1449.8x10⁶ particles/m³ for 15 minutes of UV exposure. Particle formation was found to increase with increasing concentrations of gas phase toluene, and at relative humidity of approximately 20% and higher. Variations in the initial number of particles present did not appear to have a significant effect on the particle formation, suggesting that nucleation was not a controlling factor. However, tests in a commercial environment showed no significant detectable PM2.5 formation, indicating that SOA formation during the intermittent use of germicidal UV may not significantly affect indoor air quality.

A D-grade type coal was burned under simulated domestic practices in a controlled laboratory set-up, in order to characterize emissions of volatile organic compounds (VOCs); viz. benzene, toluene, ethylbenzene and xylenes (BTEX). Near-field concentrations were collected in a shack-like structure constructed using corrugated iron, simulating a traditional house found in informal settlements in South Africa. Measurements were carried out using the Synspec Spectras GC955 real-time monitor over a three-hour burn cycle. The 3-hour average concentrations (in µg/m³) of benzene, toluene, ethylbenzene, p-xylene and o-xylene were 919 ± 44, 2051 ± 91, 3838 ±19, 4245 41 and 3576 ± 49, respectively. The cancer risk for adult males and females in a typical SA household exposure scenario, was found to be 1.1 -1.2 and 110-120 folds higher than the US EPA designated risk severity indicator (1E^-6), respectively. All four TEX compounds recorded the Hazard Quotient (HQ) of less than 1, indicating a low risk of developing related non-carcinogenic health effects. The HQ for TEX ranged from 0.001– 0.05, with toluene concentrations being the lowest and ethylbenzene the highest. This study has demonstrated that domestic coal burning may be a significant source of BTEX emission exposure.

Nowadays a recognized need for accurate observations of atmospheric aerosols (AEs) and reactive gases (RGs) exists in the framework of regional, national and global near-surface networks based on permanent or mobile measurement stations. In this context, a paramount and not-trivial issue is related to the correct execution of continuous sampling of ambient air and its subsequent distribution to measurement analyzers hosted inside the stations. Sampling artifacts must be minimized for obtaining reliable pictures of ambient air composition. To respond to this need, a suite of novel “smart” and relatively low-cost systems for the continuous sampling of ambient air was developed in the framework of the Project I-AMICA (2012 – 2015, www.i-amica.eu). These systems were designed to execute AE and RG measurements according with WMO/GAW and ACTRIS recommendations and standard operation procedures. A particular attention was dedicated to the stabilization and control of the sampling flow rates and temperatures. The analysis of one full year of operations at the WMO/GAW regional station of Capo Granitola (GAW ID: CGR, Italy), allowed to conclude that these systems are effective in meeting the technical requirements for correct execution of AE and RG measurements

Introduction: Ambient air pollution is major global health problem and commercial drivers are particularly exposed to it. No systematic assessment of the health risks associated with occupational exposure to ambient air pollution in this population has been carried out. Methods: We conducted a systematic review using a protocol-driven strategy. Papers published from inception to 20th April 2018 in MEDLINE, EMBASE, CINAHL, African journals online, Cochrane library, ISRCTN and WHO ICTRP databases were screened for inclusion by two independent reviewers. Original articles with at least an available abstract in English or French were included. Results: The initial search retrieved 1454 published articles of which 20 articles were included. 3 Studies reported a significant difference in white blood cells (106/L) among commercial motorcyclists compared to rural inhabitants (5.041±1.209 vs 5.900±1.213,p=0.001), an increased risk of lung cancer (RR=1.6, 95%CI 1.5-1.8) in bus drivers and an increased standardized mortality ratio (SMR) in bus drivers from Hodgkin’s lymphoma (SMR 2.17, 95%CI 1.19-3.87) compared to white collar workers. Other studies also found that drivers had more oxidative DNA damage and chromosome breaks. 4 papers failed to demonstrate that the drivers were more exposed to air pollution than the controls. 3 other studies also reported no significant difference in lung function parameters and respiratory symptoms. The genetic polymorphisms of detoxifying enzymes were not also homogeneously distributed compared to the controls. Conclusion: There is some evidence that occupational exposure to ambient air pollution among commercial drivers is associated with adverse health outcomes but the existing literature is limited with few studies of small sample size, methodological weaknesses and contradictory findings. Further research is recommended.

Air pollution has created a lot of problems in the developed and developing countries. To avoid or reduce these problems, constant monitoring of the air should be ensured. The conventional techniques is costly because it requires a lot of money and time consuming. Biomonitoring has been the alternative method. Moss, lichens and plants are biomonitors available to entrap air pollutants. The aim of this paper is to discuss one of the ways of monitoring air pollution – Moss bag technique. To do this, types, choice, preparation, handling of bags after preparation of moss were discussed. From the literatures consulted, it was discovered that there were differences in the techniques used by the researchers. In all, the use of mosses with emphasis on the employment of moss bag have proved to be a powerful tool in airborne particulate and toxic elements. To conclude, developing countries should focus more on this technique because it will reduce cost of air monitoring.

The development effect of water flooding in ultra-low permeability reservoir was poor due to its poor physical property and high shale content, the experimental study of air flooding which help to complement producing energy was carried out. Based on the Accelerating Rate Calorimeter experimental results, the crude oil of N block in L oilfield can produce low-temperature oxidation reaction, which was the basic condition of air flooding. Three groups of experiment natural cylinder core were designed for oil displacement, water flooding and air flooding were used respectively, and the relationship of differential pressure, oil recovery, injection capacity with injection volume was investigated. It has been showed on the result that the recovery efficiency improved sharply than water flooding, the effect of depressurization and augmented injection was obvious, and the air displacement was validation.

Pseudomonas donghuensis P482 exhibits broad antibacterial and antifungal activity, primarily related to the production of 7-hydroxytropolone (7-HT). However, the restricted nutritional conditions (viz. mineral medium with single carbon source) diminished the antagonistic activity of P482. In this study, we unveil profiles of the secondary metabolites from P482 and its selected mutants, using nutrient-diluted (10% tryptone soy broth, TSB) and nutrient-restricted (M9 with either 0.4% glucose or 0.4% glycerol as a sole carbon source) media to explore differences in the quantity and quality of the secondary metabolites produced. No 7-HT was found to be synthetized by P482 under restricted nutritional conditions. However, both the wild-type and the tested mutants of P482 still did express some antagonistic activity towards the plant pathogenic bacteria tested. Based on these results, we postulate that 7-HT is not the sole antimicrobial compound produced by P. donghuensis P482 and that other antimicrobials may be involved in P482 antagonistic activity under limiting-nutrient conditions.

This research aimed to compare the measurements recorded by a traditional PCI technology biometer (Partial Coherence Interferometry) and by a SS-OCT (Swept Source Optical Coherence Tomography) technology machine in preoperative screening of patients with age-related cataract. Optical biometry was performed with the IOLMaster 500 (version 5.5, Carl Zeiss Meditec, Germany) and the ANTERION (Heidelberg Engineering, Germany) in a total sample of 144 eyes, from 80 patients, (37 men and 43 women), with a mean age of 70.54 ± 0.739 years (range: 45-89 years) and the values of the Axial Length (AL), two meridians of the cornea (Kf, Kflat and Ks, Ksteep), astigmatism (Ast) as well as the Anterior Chamber Depth (ACD) were compared with the program IBM SPSS Statistics 27. The IOLMaster500 and ANTERION devices did not have statistically significant differences in terms of axial length and flat corneal meridian Kf, while they differed statistically significantly in terms of steep corneal meridian Ks, astigmatism and anterior chamber depth. This study suggests that a thorough pre-operative check must be performed, sometimes with more than one device, aiming at greater accuracy in the measurements of the ocular biometrics, so that we achieve more successful postoperative outcomes and ultimately more satisfied patients.

Infant electrocardiograms (ECG) and heart rates (HR) are very useful biosignals for psychological research and clinical work, but can be hard to analyze properly, particularly long form (≥5 minutes) recordings taken in naturalistic environments. Infant HRs are typically much faster than adult HRs, and so some of the underlying frequency assumptions made about adult ECGs may not hold for infants. However, the bulk of publicly available ECG approaches focus on adult data. Here, existing open-source ECG approaches are tested on infant datasets. The best performing open-source method is then modified to maximize its performance on infant data (e.g., including a 15Hz high pass filter, adding local peak correction). The HR signal is then subsequently analyzed, developing an approach for cleaning data with separate sets of parameters for the analysis of cleaner and noisier HR. A Signal Quality Index (SQI) for HR is also developed, providing insight into where a signal is recoverable and where it is not, allowing for more confidence in analysis performed on naturalistic recordings. The tools developed and reported in this paper provide a base for future analysis of infant ECG and related biophysical characteristics. Of particular importance, the proposed solutions outlined here can be efficiently applied to real-world large datasets.

The latest experimental measurements of cosmic rays (CRs) have discovered a series of anomalies, including the hardening of the nuclear spectra at R ∼200 GV followed by softening at R ∼10 TV and complicated energy dependence of anisotropy from GeV to PeV. Recent works have demonstrated nearby sources are crucial for these anomalies of spectra and anisotropy. In this work, we analyze the contributions of five nearby sources within 1 kpc around solar system to the spectra and anisotropy, finally find out which source is the best candidate source. In the calculation process, we also introduce the anisotropic diffusion of CRs induced by the local interstellar magnetic field (LIMF) nearby the solar system based on spatial-dependent propagation (SDP) model. As a result, we find Geminga SNR source can simultaneously account for CR spectra and anisotropy, whereas the other sources can not . Measurements of CR anisotropy and spectra by experiments such as LHAASO and HAWC are expected to test this scenario in the near future.

The object of research is an optical-electronic system for recording and processing signals from fiber-optic sensors. Due to the use of optical fibers as sensitive elements, there is no influence on the measurement result of electromagnetic fields, spurious electromagnetic radiation, channel crosstalk, there are no problems, electrical safety is significantly increased, there are no problems of arcing and sparking. A scheme of a receiving-transmitting module has been developed, which is additionally equipped with a preliminary protection and filtering system. Further, measuring tracks, microcontroller software and functional tests were ordered to determine the metrological properties of the proposed system.Signal integrity analysis is presented, which allows you to check whether the signals present in the device are correctly transmitted between their sources and receivers. The analysis of signal integrity is investigated, which is performed in two stages of the device design process. Modeling of the studied module in the specialized program Altium Designer. With the help of this program, potential problems were found, such as the occurrence of crosstalk between paths, the exact values of some elements, accurate analytical calculation. Learned an impedance analysis trace for a given connection's parameters, where the value affects the shape of the given path, its physical dimensions, distance from other paths, and other physical properties of the board. Optoelectronic system for recording and processing signals from fiber optic sensors based on Bragg fiber gratings resistant to electromagnetic interference and temperature, for use in modern systems for monitoring building structures, bridges, tunnels, dams, high-rise buildings, railways, oil platforms, buildings, pipelines.

To solve the problem of low efficiency of source seeking in implicit information field, this paper presents an autonomous souring method based on balanced searching strategy is enlighten by biological homing behaviors. At the beginning of the research, the source seeking task come down to a multi-objective convergence issue. By taking the feasibility search behaviors as the individual sample of the evolutionary population drawing on the thought of evolutionary algorithms, then combine motion searching with population evolution, so the carrier can be guide to complete source seeking task by solving the multi-objective problem. Furthermore, the distribution entropy is also considerated d to measure the searching bias in the process of source seeking. Combined with the demand of the source seeking process, a new source seeking method of balanced searching strategy is designed. Ultimately, through theoretical analysis and simulation verification confirm the effectiveness and rationality of the proposed method.

A low-cost medium power carbon dioxide (CO₂) laser system is designed, constructed, and characterized to produce coherent, monochromatic laser radiation in the Infrared region. The laser cavity is simulated and designed by using ZEMAX optic studio. A switch-mode high tension pump source is designed and constructed using a flyback transformer and simulated using NI Multisim to study the voltage behavior at different node points. A prototype cooling system/chiller is designed and built using the Thermo-Electric Coolers (TEC) to remove the excess heat produced during laser action. Various parameters, like pumping mechanism, chiller stability, efficiency, output power, and current at different applied voltages, are studied. The chiller efficiency at different output powers of the laser is analyzed, which clearly shows that the chiller's cooling rate is good enough to compensate for the heat generated by the laser system. The center wavelength of the carbon dioxide laser is 10.6μm with FWHM of 1.2nm simulated in the ZEMAX optic studio. The output beam penetration through salt rock (NaCl), wood, and acrylic sheet at various output powers is analyzed to measure the penetration depth rate of the CO₂ laser.

The Laser Thermal-Joule Heating Composite Process was studied by orthogonal tests based on an analysis of fabrication parameters such as the laser power, wire feeding speed, and electric current. Temperature profiles and the geometric morphology of deposited layers under different process parameters were analyzed, and the overlaps between the layers and the substrate were observed. Results show that when the temperature at the bottom layer of the additive manufacturing is higher than the melting point of the substrate, and the highest temperature at the top layer does not exceed the over-firing temperature, good morphology and close bonding with the substrate can be obtained. Finally, appropriate process parameters were identified and verified to print multiple layers continuously.

Cognitive biases are an important factor contributing to the development and symptom severity of psychosis. Despite that various cognitive biases are contributing to psychosis, they are rarely investigated together. In the current systematic review, we aimed at investigating specific and shared neural correlates of two important cognitive biases: aberrant salience and source monitoring. We conducted a systematic search of fMRI studies of said cognitive biases. Eight studies on aberrant salience and eleven studies on source monitoring were included in the review. We critically discussed behavioural and neuroimaging findings concerning cognitive biases. Various brain regions are associated with aberrant salience and source monitoring in individuals with schizophrenia and the risk of psychosis. Ventral striatum and insula contribute to aberrant salience. The medial prefrontal cortex, superior and middle temporal gyrus contribute to source monitoring. The anterior cingulate cortex and hippocampus contribute to both cognitive biases, constituting a neural overlap. Our review indicates that aberrant salience and source monitoring may share neural mechanisms, suggesting their joint role in producing disrupted external attributions of perceptual and cognitive experiences, thus elucidating their role in positive symptoms of psychosis. Account bridging mechanisms of these two biases is discussed. Further studies are warranted.

Small Shallow Lakes (SSL) support exceptionally high and original biodiversity, providing numerous ecosystem services. Their small size makes them especially sensitive to anthropic activities, that causes a shift to dysfunctional turbid states and induces loss of services and biodiversity. In this study we investigated the relationships between environmental factors and macrophyte communities. Macrophytes play a crucial role in maintaining functional clear states. Better understanding factors determining the composition and richness of aquatic plant communities in least-impacted conditions may be useful to protect them. We inventoried macrophyte communities and collected chemical, climatic and morphological data from 89 least-impacted SSL widely distributed in France. SSL were sampled across four climatic ecoregions, various geologies and elevations. Hierarchical cluster analysis showed a clear separation of four macrophyte assemblages strongly associated with mineralisation. Determinant factors identified by db-RDA analysis are, in order of importance, geology, distance from source (DIS, a proxy for connectivity with river hydrosystems), surface area, climate and hydroperiod (water permanency). Surprisingly, at country-wide scale, climate and hydroperiod filter macrophyte composition weakly. Geology and DIS are the major determinants of community composition, whereas surface area determines floristic richness. DIS is identified as determinant in freshwater lentic ecosystems for the first time.

This paper aims to investigate the airflow that can transport emission sources of PM2.5 from neighboring countries to contribute to air pollution in northern Thailand. We applied the coupled atmospheric and air pollution model which is based on the Weather Research and Forecasting Model (WRF) and a Hybrid Single-Particle Lagrangian Integrated Trajectory Model (HYSPLIT). The model output was compared to the ground-based measurement from the Pollution Control Department (PCD) to examine model performance. As a result of model evaluation, the meteorological variables fairly agreed well compared to observation with Index of Agreement (IOA) in ranges of 0.57 to 0.79 for temperature and 0.32 to 0.54 for wind speed, while the fractional bias of temperature and wind speed were 1.3 to 2.5 °C and 1.2 to 2.1 m/s. Burma was a country that contributed much of hotpot locations by 37% of the entire hotspot locations of Southeast Asia in March. The influence of the Asian Monsoon can bring pollutants from neighboring countries such as Burma and Laos toward northern Thailand in March that likely contribute to high concentrations of PM2.5 in northern Thailand.

(1) Background: In nervous system information is conveyed by a sequence of action potentials, called spikes-trains. As MacKay and McCulloch proposed, spike-trains can be represented as bits sequences coming from Information Sources. Previously, we studied relations between Information Transmission Rates (ITR) carried out by the spikes, their correlations, and frequencies. Here, we concentrate on the problem of how spikes fluctuations affect ITR. (2) Methods: The Information Theory Method developed by Shannon is applied. Information Sources are modeled as stationary stochastic processes. We assume such sources as two states Markov processes. As a spike-trains' fluctuation measure, we consider the Standard Deviation sigma, which, in fact, measures average fluctuation of spikes around the average spike frequency. (3) Results: We found that character of ITR and signal fluctuations relation strongly depends on the parameter s which is a sum of transitions probabilities from no spike state to spike state and vice versa. It turned out that for smaller s (s<1) the quotient ITR\sigma has a maximum and can tend to zero depending on transition probabilities. While for s large enough (1<s) the ITR\sigma is separated from 0 for each s. Similar behavior was observed also when we replaced Shannon entropy terms in Markov entropy formula by their approximation with polynomials. We also show that the ITR quotient by Variance behaves in a completely different way. (4) Conclusions: Our results show that for large transition parameter s the Information Transmission Rate by sigma will never decrease to zero. Specifically, for 1<s<1.7 the ITR will be always, independently on transition probabilities which form this s, above the level of fluctuations, i.e. in this case we have sigma<ITR. Thus, we conclude that in a more noisy environment, to get appropriate reliability and efficiency of transmission, Information Sources with higher tendency of transition from the state no spike to spike state and vice versa should be applied.

The importance of ICTs for dissemination of information to farmers has been verified by extension practitioners, information and communication scholars, policy makers and development agencies. Information related to new seed varieties, production technologies, livestock breeds, vaccines, including weed and pest control, as well as relevant market information is constantly required by smallholder farmers. The identification of specific attributes among smallholder farmers which contributes to their adoption of a proposed ICT-based information source provides an important tool for developing interventions which address the information needs of farmers. Using a literature survey methodology, pertinent studies related to adoption of ICTs, farmers’ information source usage and relevant frameworks were identified, including applicable theories and models in technology adoption and information behaviour. In the proposed framework, the socio-economic characteristics of smallholder farmers were posited as key variables influencing smallholder farmers, within a farming system, to adopt ICT-based information sources. The framework contributes to discern the prospects of adopting ICT-based information sources by individual farmers within a farming system, and may also envisage other related welfare outcomes and market participation pathways among smallholder farmers. The review also addresses the paucity of conceptual discourse, while contributing to a growing pool of research on ICT in African agriculture.

Several studies have shown that changes in incoming solar radiation and variations of the diffuse fraction can significantly modify the vegetation carbon uptake. Hence, monitoring the incoming solar radiation at large scale and with high temporal frequency is crucial for this reason along with many others. The EUMETSAT Satellite Application Facility for Land Surface Analysis (LSA SAF) operationally disseminates in near real time estimates of the downwelling shortwave radiation at the surface since 2005. This product is derived from observations provided by the SEVIRI instrument onboard the Meteosat Second Generation series of geostationary satellites, which covers Europe, Africa, the Middle East, and part of South America. However, near real time generation of the diffuse fraction at the surface level has only recently been initiated. The main difficulty towards achieving this goal was the general lack of accurate information on the aerosol particles in the atmosphere. This limitation is nowadays less important thanks to the improvements in atmospheric numerical models. This study presents an upgrade of the LSA-SAF operational retrieval method, which provides the simultaneous estimation of the incoming solar radiation and its diffuse fraction from satellite every 15 minutes. The upgrade includes a comprehensive representation of the influence of aerosols based on physical approximations of the radiative transfer within an atmosphere-surface associated medium. This article explains the retrieval method, discusses its limitations and differences with the previous method, and details the characteristics of the output products. A companion article will focus on the evaluation of the products against independent measurements of solar radiation. Finally, the access to the source code is provided through an open access platform in order to share with the community the expertise on the satellite retrieval of this variable.

In this study, a matched-mode autoregressive source depth estimation method (MMAR) based on autoregressive (AR) wavenumber estimation is proposed for a moving source in shallow water waveguides. The signal original frequency and the environmental parameters, namely, the sound speed profile and bottom properties are known as a prior knowledge. The mode wavenumbers are estimated by the AR modal wavenumber spectrum. On the basis of the mode wavenumber estimation, the mode amplitudes can be estimated by the wavenumber spectrum that is obtained by generalized Hankel transform. The source depth estimation is determined by the peak of source depth function wherein the data mode best matches the replica mode that is calculated using a propagation model. Compared with other methods of moving source depth estimation, the proposed method exhibits a better performance in source depth estimation under low signal-to-noise ratio or the small range span. The selection of horizontal line array depth is illustrated by simulation and normal mode theory in details.

Ethylene Oxide (EtO) is a colorless, flammable gas at room temperature, produced by the catalytic oxidation of ethylene. EtO is widely used by medical sterilization facilities to clean medical supplies and equipment. Recent epidemiological studies showed that EtO is a more potent carcinogen than previously documented, leading the Environmental Protection Agency (EPA) to update, in December 2016, the inhalation unit risk estimate for EtO. This resulted in the identification of EtO as a potential health concern in several areas across the US, including the state of Utah. The geography surrounding Salt Lake Valley creates a bowl; ideal for collecting air pollution emissions. The region often experiences inversion episodes which inhibit vertical mixing and cause an accumulation of air pollutants, leading to unhealthy pollution levels. Using the EPA's dispersion modeling software, AERMOD, this study estimated EtO concentrations through facility stack and fugitive emissions modeling results. These values were compared with those of canister-based concentrations from ambient air samples taken near a medical device sterilization facility in the Salt Lake Valley. Stainless steel, whole-air passivated canisters were used to collect 24-hour ambient concentration samples of EtO. Eight locations surrounding a Salt Lake Valley medical device sterilization facility and four background sites were chosen to measure the ambient concentrations. Accounting for potential atmospheric impacts on EtO, measurements were sampled in winter 2022 (January-March) and summer 2022 (July-September). The modeled EtO concentrations were adjusted to account for background values associated with the winter or summer data. Then the two methodologies were compared using a Wilcoxon Sign-ranked, paired test. The statistical analysis resulted in six of the eight sample locations surrounding the sterilization facility being significantly different when comparing canister-based measurements of ambient EtO to modeled estimates. Canister-based measurements taken at sites one, three, and four were statistically greater than the modeled estimates, while sites two, five, and seven were statistically less than the modeled estimates. Also, the summer background value calculated was almost 2.5 times greater than the winter. The results do not suggest whether one method is more or less conservative than the other. In conclusion, the five of the closest sites and site seven were statistically different when comparing measured and modeled ambient concentrations of EtO. The comparison results do not clearly indicate if a correction factor could be derived for future human exposure to cancer risk assessment modeling. However, it is reasonable that the closer to the sterilization facility, the more total EtO exposure will be realized.

UV-A (ca. 365 nm wavelength, a.k.a. 'black light') photocatalysis has been investigated to comprehensively mitigate odor and selected air pollutants in the livestock environment. This study was conducted to confirm the performance of UV-A photocatalysis on the swine farm. The objectives of this research were to (1) scale-up of the UV-A photocatalysis treatment, (2) evaluate the mitigation of odorous gases from swine slurry pit, and (3) test different UV sources, (4) evaluate the effect of suspended particulate matter (PM), and (5) conduct preliminary economic analyses. We tested UV-A photocatalysis at a mobile laboratory-scale capable of treating ~0.2 - 0.8 m3·s-1 of barn exhaust air. The targeted gaseous emissions of barn exhaust air were significantly mitigated (p < 0.05) up to 40% reduction of measured odor; 63%, 44%, 32%, 40%, 66%, and 49% reduction of dimethyl disulfide, isobutyric acid, butanoic acid, p-cresol, indole, and skatole, respectively; 40% reduction of H2S; 100% reduction of O3; and 13% reduction of N2O. The PM mitigation effect was not significant. Formaldehyde levels did not change, and a 21% generation of CO2 was observed. The percent reduction of targeted gases decreased as the airborne PM increased. Simultaneous chemical and sensory analysis confirmed that UV-A treatment changed the overall nuisance odor character of swine barn emissions into weaker manure odor with 'toothpaste and 'mint' notes. The smell of benzoic acid generated in UV-A treatment was likely one of the compounds responsible for the less-offensive overall odor character of the UV-treated emissions. Results are needed to inform the design of a farm-scale trial, where the interior barn walls can be treated with the photocatalyst, and foul air will be passively treated as it moves through the barn.

(1) Aim of the study was to investigate the spatial and temporal characteristics of the airflow created by two commercially available non-contact tonometers, the CorvisST and the Ocular Re-sponse Analyser. (2) The airflow pressure was measured using a MEMS pressure sensor to inves-tigate the spatial and temporal distribution. The airflow from the CorvisST and Ocular Response Analyser were mapped to a 600µm and a 1mm resolution grid, respectively. (3) Central airflow pressure of the CorvisST (96.4 ± 1.4)mmHg was higher than the Ocular Response Analyser (91.7 ± 0.7)mmHg. The duration of the air-puffs also differed, with the CorvisST showing a shorter du-ration (21.483 ± 0.2881)ms than the ORA (23.061 ± 0.1872)ms. The rising edge of the CorvisST airflow pressure profile demonstrated a lower gradient (+8.94mmHg/ms) compared to the Oc-ular Response Analyser (+11.00mmHg/ms). Both had similar decay response edges; CorvisST -11.18mmHg/ms, Ocular Response Analyser -11.65mmHg/ms. (4) The study presents a valid method to investigate physical dimensions of the airflow pressure of non-contact tonometers. Novel findings relating to the magnitude, duration and spatial characteristics of the respective airflow pressures are reported. It is anticipated that this information will better inform clinical studies and theoretical models relating to ocular biomechanics.

Environmental impact associated with odor and gaseous emissions from animal manure is one of the challenges for communities, farmers, and regulatory agencies. Microbe-based manure additives treatments are marketed and used by farmers for mitigation of emissions. However, their performance is difficult to assess objectively. Thus, comprehensive, practical, and low-cost treatments are still in demand. We have been advancing such treatments based on physicochemical principles. The objective of this research was to test the effect of the surficial application of a thin layer (¼"; 6.3 mm) of biochar on the mitigation of gaseous emissions (as the percent reduction, % R) from swine manure. Two types of biochar were tested: highly alkaline and porous (HAP) biochar made from corn stover and red oak (RO), both with different pH and morphology. Three 30-day trials were conducted with a layer of HAP and RO (2.0 & 1.65 kg∙m^-2, respectively) applied on manure surface, and emissions of ammonia (NH₃), hydrogen sulfide (H₂S), greenhouse gases (GHG), and odorous volatile organic compounds (VOCs) were measured. The manure and biochar type and properties had an impact on the mitigation effect and its duration. RO significantly reduced NH₃ (19-39%) and p-cresol (66-78%). H₂S was mitigated (16~23%), but not significantly for all trials. Significant (66~78%) reductions for p-cresol were observed for all trials. The phenolic VOCs had relatively high % R in most trials but not significantly for all trials. HAP reduced NH₃ (4~21%) and H₂S (2~22%), but not significantly for all trials. Significant % R for p-cresol (91~97%) and skatole (74~95%) were observed for all trials. The % R for phenol and indole ranged from (60~99%) & (29~94%) but was not significant for all trials. The impact on GHGs, isobutyric acid, and the odor was mixed with some mitigation and generation effects. However, larger-scale experiments are needed to understand how biochar properties and the dose and frequency of application can be optimized to mitigate odor and gaseous emissions from swine manure. The lessons learned can also be applicable to surficial biochar treatment of gaseous emissions from other waste and area sources.

The aim of this research was to investigate the mass, substances and energy flow through two-stroke low speed Diesel engines. For this reason, a zero-dimensional model of the combustion in the engine was developed with a calculated amount and composition of exhaust gases. Due to the large amount of oxygen in the exhaust gases, a ratio of real air consumption and stoichiometric amount of air required for combustion of injected fuel was set. The calculated ratio showed that the engine consumes four times more air than needed for combustion in AFR_stoich. In this work it is called the Air Consumption Factor or Ratio and has not been mentioned in scientific literature before. Air Consumption Ratio is defined as a factor of dry or humid air. To be more comprehensive, a modified diagram of composition of the flow in and out of a two-stroke fuel injection engine and the cylinder was drawn.

Accurate prediction of mercury content emitted from fossil-fueled power stations is of utmost importance for environmental pollution assessment and hazard mitigation. In this paper, mercury content in the output gas of power stations’ boilers was predicted using an adaptive neuro-fuzzy inference system (ANFIS) method integrated with particle swarm optimization (PSO). The input parameters of the model include coal characteristics and the operational parameters of the boilers. The dataset has been collected from 82 power plants and employed to educate and examine the proposed model. To evaluate the performance of the proposed hybrid model of ANFIS-PSO model, the statistical meter of MARE% was implemented, which resulted in 0.003266 and 0.013272 for training and testing, respectively. Furthermore, relative errors between acquired data and predicted values were between -0.25% and 0.1%, which confirm the accuracy of the model to deal nonlinearity and representing the dependency of flue gas mercury content into the specifications of coal and the boiler type.

Code summarization plays a vital role in aiding developers with program comprehension by generating corresponding textual descriptions for code snippets. While recent approaches have concentrated on encoding the textual and structural characteristics of source code, they often neglect the global hierarchical features causing limited code representation. Addressing this gap, our paper introduces the Statement-grained Hierarchy enhanced Transformer model (SHT), a novel framework that integrates global hierarchy, syntax, and token sequences to automatically generate summaries for code snippets. SHT is distinctively designed with two encoders to learn both hierarchical and sequential features of code. One relational attention encoder processes the statement-grained hierarchical graph, producing hierarchical embeddings. Subsequently, another sequence encoder integrates these hierarchical structures with token sequences. The resulting enriched representation is then fed into a vanilla Transformer decoder, which effectively generates concise and informative summarizations. Our extensive experiments demonstrate that SHT significantly outperforms state-of-the-art approaches on two widely used Java benchmarks. This underscores the effectiveness of incorporating global hierarchical information in enhancing the quality of code summarizations.

Digital music is one of the most important things in market due to the music royalties’ distribution in Korea. As the music market is transformed to the digital music market such as download the music and streaming, the distribution of music royalties starting from online service provider (OSP) has come to be a highly important part for music rights holders. One of the most important issues in current music royalties’ distribution in Korea is the unfair way of music royalties due to indiscriminative repeat streaming of digital music. To prevent this, music log usage data from several OSPs was collected in day-based system, however, there was a limit to identify detailed information on the use of music in current state. This paper analyzed the structural problems and limitations of settlement of music royalties, and provides a structure in which there can be transparent settlement and distribution between users and rights holders as one of the institutional measures. We’ll also propose various AI-based applications using music log usage data. The proposed system will hopefully be used for public purposes.

Single photon ionization (SPI) based on vacuum ultraviolet (VUV) lamps has been extensively investigated and applied due to its clean mass spectra as a soft ionization method. However, the photon energy of 10.6 eV and photons flux of 106 photons/s of commercial VUV lamp limits its range of ionizable analytes as well as sensitivity. This work designs a chemical ionization focusing integrated (CIFI) ionization source time-of-flight mass spectrometry (TOFMS) based on VUV lamp for the detection of volatile organic compounds (VOCs) and oxygenated volatile organic compounds (OVOCs). The photoelectrons obtained from the VUV lamp through the photoelectric effect ionized the oxygen in the air to obtain the reagent ions O2+, and segmented quadrupole constituted the ion-molecule-reaction region (IMR) and radially focused the ions using a radio-frequency electric field, which improved the yield and transport efficiency of the sample ions and the sensitivity of mass spectrometry, resulting in 44-fold and 1154-fold increase in signal response to benzene and pentanal, respectively. To verify the reliability of the ionization source, the linear correspondence and repeatability of benzene and pentanal were investigated. Satisfactory dynamic linearity was obtained in the concentration range of 5-50 ppbv, and daytime RSD reached 3.91% and 6.26%, respectively. Finally, the CIFI ionization source TOFMS was applied to the determination of OVOCs, and the LOD of 12 types of OVOCs can reach the pptv level, indicating that the ionization source has the potential for accurate and sensitive online monitoring of atmospheric OVOCs.

Pore fluid pressure is very important to the generation, migration and accumulation of petroleum. The previous studies indicate that the Chezhen sag region is typically characterized by pore fluid overpressure (the difference between pore fluid pressure and hydrostatic pressure). To date, the formation mechanism of pore overpressure and the accumulation regularity of “upper source-lower reservoir” type in this region remains unknown. In order to investigate these problems, a 2-D finite element model is established with regards to the fluid-solid coupling in Chegu 25 block of Chezhen depression, fully considering the existing seismic, logging data and regional tectonic stress environment. Meanwhile, we calculate the abnormal overpressure generated at the source rock during hydrocarbon generation and the process of hydrocarbon migration and accumulation along the faults, analyzing the dynamic conditions of hydrocarbon downward accumulation. The results show that overpressure can accelerate migration of hydrocarbon and improve the efficiency of hydrocarbon accumulation. However, when the overpressure is too large, tensile fractures and shear fractures may occur, resulting in hydrocarbon dissipation, and changing the results of oil and gas accumulation. The overpressure at the source rock is mainly caused by hydrocarbon generation, while the overpressure at the reservoir is primarily created by unbalanced compaction. As the dominant channel of hydrocarbon migration, overpressure will change the direction and path of hydrocarbon migration in the fault. Therefore, the “upper source-lower reservoir” hydrocarbon accumulation model is strongly explained by the high permeability of faults and the presence overpressure. In summary, the simulated overpressure results are in good agreement with the mud weight equivalent overpressure and the drill stem tests (DSTs).

Groundwater plays a crucial role in triggering and reactivating deep-seated landslides. However, classical hydrogeological investigations have limitations in their applicability to deep-seated landslides due to anisotropic and heterogeneous media[16]. The Huangtupo landslide in the Three Gorges reservoir area has garnered significant attention in China due to its large volume, complex geological structure, and high hazard potential. Recent monitoring data has shown notable deformation in the NO.1 Riverside Sliding Mass (HTP-1), one of the four parts of the Huangtupo landslide, making it the primary focus of landslide research. This study aimed to investigate the water sources in the HTP-1 landslide using environmental stable isotopes as tracers. The isotopic analysis results indicated that the groundwater in the landslide area (LGW) is a mixture of remote karst groundwater (KGW) from the adjacent up-slope and local precipitation (LP). The karst groundwater is a major contributor to the recharge of the landslide groundwater system, causing a high slope groundwater level that can easily exceed the critical level during heavy rainfall events. Furthermore, based on the differential distribution of the LP fraction of LGW at different locations, the groundwater in the landslide can be classified into three groups. Groundwater at the sliding rupture surface has the highest fractions of local precipitation, followed by the groundwater at the rear of the landslide. Combined with the monitoring data of groundwater level in boreholes during the rainy season, this indicates that fissures and fractures in the sliding rupture zone and at the back of the landslide are well connected, which could be a critical factor in the mass movement of the creeping slope.

The Coronavirus disease 2019 (COVID-19) rapidly spread to over 180 countries and abruptly disrupted the production rates and supply chains worldwide. Since then, 3D printing also recognized as additive manufacturing (AM) and known to be a novel technique that uses layer-by-layer deposition of material to produce the intricate 3D geometry, has been engaged in reducing the distress caused by the outbreak. During the early stages of this pandemic, shortages of Personal Protection Equipment (PPE), including facemasks, shields, respirators, and other medical gears, were significantly answered by remotely 3D printing them. Amidst the growing testing requirements, the 3D printing emerged as a potential and fast solution manufacturing process to meet the production needs due to its flexibility, reliability, and rapid response capabilities. In the recent past, some of the other medical applications that have gained prominence in the scientific community include 3D printed ventilator splitters, device components, and patient-specific products. Regarding the non-medical applications, researchers have successfully developed contact-free devices to address the sanitary crisis in public places. This work aims to systematically review the applications of 3D printing or AM techniques that have been involved in producing various critical products essential to limit this deadly pandemic's progression.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

Human activities for exploitation and utilization of coastal zones have transformed coastline morphology and severely changed regional flow fields, underwater topography, and sediment distribution in the sea. In this study, single-beam bathymetry coupled with sediment sampling and analysis was carried out to ascertain submarine topography, geomorphology and sediment distribution patterns and explore sediment provenance in Qinzhou Bay, China. The results show the following. 1) The underwater topography in Qinzhou Bay is complex and variable, with water depths in the range of 0–20 m. It can be divided into four underwater topographic zones: the central (outer Qinzhou Bay), eastern (Sanniang Bay), western (east of Fangcheng Port), and southern (outside of the bay) parts. 2) Based on geomorphological features, the study area comprises four major submarine geomorphological units (i.e., tide-dominated delta, tidal sand ridge group, tidal scour troughs, and underwater slope) and two intertidal geomorphological units (i.e., tidal flat and abrasion platforms). 3) Sandy sediments are widely present in Qinzhou Bay, accounting for 70% of the total sediments. From the mouth of the Maowei Sea to the offshore, the sediments gradually become coarser, shifting from sandy mud to muddy sand, and then to fine sand and medium–coarse sand. The detrital minerals contained in the sediments mainly consist of quartz, feldspar, debris, ilmenite, leucosphenite, and tourmaline, whereas the clay minerals are dominated by kaolinite, followed by illite and smectite. The sediment provenance is mainly terrigenous input from near-source rivers. With sea reclamation and dam construction, outer Qinzhou Bay has experienced enormous morphological variation of its coastline. Together with the channel effect where the velocity of ebb tide is greater than that of flood tide, the underwater topography is characterized by increased scale and height difference of troughs and ridges as well as enhanced offshore deposition.

3D printing is described as the third industrial revolution: its impact is global in industry and progresses every day in society. It presents a huge potential for ecology and evolution, sciences with a long tradition of inventing and creating objects for research, education and outreach. Its general principle as an additive manufacturing technique is relatively easy to understand: objects are created by adding material layers on top of each other. Although this may seem very straightforward on paper, it is much harder in the real world. Specific knowledge is indeed needed to successfully turn an idea into a real object, because of technical choices and limitations at each step of the implementation. This article aims at helping scientists to jump in the 3D printing revolution, by offering a hands-on guide to current 3D printing technology. We first give a brief overview of uses of 3D printing in ecology and evolution, then review the whole process of object creation, split into three steps: (1) obtaining the digital 3D model of the object of interest, (2) choosing the 3D printing technology and material best adapted to the requirements of its intended use, (3) pre- and post-processing the 3D object. We compare the main technologies available and their pros and cons according to the features and the use of the object to be printed. We give specific and key details in appendices, based on examples in ecology and evolution.

The combination of new-generation information technology and manufacturing technology has resulted in major and profound impact on future development paradigm of manufacturing. It is challenging for existing methods to conduct a multidimensional trend exploration related to machine tool domain, which is the basis of virtually everything in manufacturing. In this paper, we proposed an integrating approach framework combined topic models, bibliometric, trend analysis and patent analysis to mine insightful information about future development from multi-source data related to machine tool, such as papers, grants, patents and news. Specifically, papers and grants provided two different perspectives to explore the current focuses and future trends in machine tool research. Furthermore, the future technology development of machine tool was investigated through patents analysis. Finally, news related to machine tool industry in recent years was analyzed to analyze future machine tool business mode. The integration of the above various analytical methods and the multi-dimensional mining of literatures enabled the analysis of the future development of machine tool domain systematically from multi-perspectives which include research, technology development and industry. The conclusions obtained in this paper is beneficial to different communities of machine tool in terms of determining the research directions for researchers, identifying industry opportunities for corporations and developing reasonable industry policy for policy makers.

3D object reconstruction from depth image streams using Kinect-style depth cameras has been extensively studied. In this paper, we propose an approach for accurate camera tracking and volumetric dense surface reconstruction assuming a known cuboid reference object is present in the scene. Our contribu¬tion is three-fold. (a) We maintain drift-free camera pose tracking by incorporating the 3D geometric constraints of the cuboid reference object into the image registration process. (b) We reformulate the problem of depth stream fusion as a binary classification problem, enabling high-fidelity surface reconstruction, especially in the con¬cave zones of objects. (c) We further present a surface denoising strategy to mitigate the topological inconsistency (e.g., holes and dangling triangles), which facilitates the generation of a noise-free triangle mesh. We extend our public dataset CU3D with several new image sequences, test our algorithm on these sequences and quantitatively compare them with other state-of-the-art algorithms. Both our dataset and our algorithm are available as open-source content at https://github.com/zhangxaochen/CuFusion for oth-er researchers to reproduce and verify our results.

The urbanisation phenomenon and related cities expansion and transport networks entail preventing the increase of population exposed to environmental pollution. Regarding noise exposure, the Environmental Noise Directive demands on main metropolis to produce noise maps. While based on standard methods, these latter are usually generated by proprietary software and require numerous input data concerning, for example, the buildings, land use, transportation network and traffic. The present work describes an open source implementation of a noise mapping tool fully implemented in a Geographic Information System compliant with the Open Geospatial Consortium standards. This integration makes easier at once the formatting and harvesting of noise model input data, cartographic rendering and output data linkage with population data. An application is given for a French city, which consists in estimating the impact of road traffic-related scenarios in terms of population exposure to noise levels both in relation to a threshold value and level classes.

Centrifuges are commonly required devices in medical diagnostics facilities as well as scientific laboratories. Although there are commercial and open source centrifuges, costs of the former and required electricity to operate the latter, limit accessibility in resource-constrained settings. There is a need for low-cost, human-powered, verified and reliable lab-scale centrifuge. This study provides the designs for a low-cost 100% 3-D printed centrifuge, which can be fabricated on any low-cost RepRap-class fused filament fabrication (FFF) or fused particle fabrication (FPF)-based 3-D printer. In addition, validation procedures are provided using a web camera and free and open source software. This paper provides the complete open source plans including instructions for fabrication and operation for a hand-powered centrifuge. This study successfully tested and validated the instrument, which can be operated anywhere in the world with no electricity inputs obtaining a radial velocity of over 1750rpm and over 50N of relative centrifugal force. Using commercial filament the instrument costs about US$25, which is less than half of all commercially available systems; however, the costs can be dropped further using recycled plastics on open source systems for over 99% savings. The results are discussed in the contexts of resource-constrained medical and scientific facilities.

In the last decades, numerous studies indicated the substantial role semiconductors could play in photocatalytic processes for environmental applications. Materials that contain a semi-conductor as a photo-catalyst have a semi-permanent capacity for removing harmful gases from the ambient air. In the present work, the focus is on TiO2. Heterogeneous photo-catalysis using TiO2 leads to the degradation of NO/NO2, benzene, toluene, and other priority air pollutants once in contact with the semiconductor surface. Preliminary evidence indicates that TiO2 containing construction materials and paints efficiently destroy the ozone precursors NO and NO2 up to 80% and 30%, respectively. Therefore, the development of innovative coatings containing TiO2 as a photo-catalyst was in the foreground of research activities with the aim to be used as building and construction materials mainly outdoors, e.g. on building facades in high traffic roads for the degradation of priority air pollutants (NOx and volatile organic compounds) in the polluted urban atmosphere. Though the advantages connected with the application of TiO2 due to its band gap of 3.2 eV are limited. TiO2 is effective only in the UV-region (ca. 5%) of the solar spectrum with wavelengths λ

(1)Background：To date, no studies have epidemiologically examined whether the concentration of particulate matter (PM) 2.5 and its ionic components is related to the prevalence of skin symptoms. Therefore, this study aimed to clarify this association in patients with allergic diseases. (2)Methods: From February 1 to May 31, 2020, we evaluated the daily prevalence of skin symptoms in outpatients with allergic diseases being treated at Fukuoka Hospital, Fukuoka, Japan, and measured the concentration of PM2.5 and its ionic components. （3）Results: Univariate analysis showed a statistically significant association between skin symptoms and the concentration of PM2.5 and the ionic components SO42-, NH4+, K+, and Mg2+, and multivariate analysis showed a statistically significant association between the daily prevalence of skin symptoms and the concentration of the ionic components SO42- or Mg2+. (4)Conclusions: Our findings indicate that the concentration of some PM2.5 ionic components may affect skin symptoms in patients with allergic diseases.

Spray penetration into citrus canopies is critical for adequate coverage and deposition to ensure effective pest control. However, mismatch of air assistance to target canopy characteristics can lead to unintended spray loss through over penetration. To evaluate the effect of air assistance on on-target deposition, two sprayers (surrogates for airflow rates) were used to apply a fluorescent tracer dye solution @ target concentration of 300 ppm to 16 medium foliage density tree blocks in a commercial mandarin orchard. The complete factorial experiment in three replications comprised two ground speeds (1.6 and 4.8 km/h), two disc-core nozzles (TeeJet® D3-25 and D6-45), and either one or two nozzle rows to obtain a wide range of application rates (496 to 9,719 L/ha). Dye deposition significantly decreased with canopy depth (p=&lt;0.001) by nearly 7 times across the 3.4-m-wide canopies but was not significant over 1.2 to 2.2 m sampling height (p=0.867). Deposition obtained with the low airflow rate sprayer was significantly greater (p=&lt;0.001) than that obtained with the high airflow rate sprayer over the dose range likely due to too much air pushing out spray droplets. This study underscores the importance of matching the air assistance of orchard sprayers to the target canopy.

Ethiopian Airlines is a leading airline in the world. Its supply chain management is one of the most critical aspects in achieving its sustainability objectives. The present study aims to assess the sustainability practices and strategies of Ethiopian Airways in its supply chain, identifying areas for improvement and recommending strategies for enhancing sustainability. The study concentrates on pertinent sustainability concerns within the aviation sector while examining antecedent research on the sustainability of Ethiopian Airlines’ supply chain management strategies. The findings of the study reveal that there are several areas in need of improvement, including the implementation of waste reduction measures, the establishment of a recycling program, and the reduction of single-use plastic usage. It is suggested that promoting responsible tourism embodying sustainable practices is imperative, particularly within the airline context.

In this paper we present a city-scale (possibly global) air pollution network made of low-cost sensors for particulate matter concentration in the air. The components of presented system are based on our research and experience from previous studies focused on air quality instruments and sensors for addressing urban air pollution. Sensor nodes are produced locally and distributed over a city of Sarajevo, Bosnia and Herzegovina. The system collects, calibrates and displays particulate metal concentrations in real-time. In comparison to the available measurements from governmental institutions, our system demonstrated good agreement of measured parameters, with several advantages including: higher resolution in space and time, lower costs, both horizontal and vertical measurements and many more. One of the capabilities of the system is the real-time air pollution city map with animations. By installing multiple sensor nodes over a slope (cable car), we receive vertical measurements of temperature, humidity and particulate matter concentration in real time, which gives a valuable insight into the dynamics of temperature inversion episodes and air pollution below the inversion layer.

Air pollution is a situation that negatively affects the health of humans and all living things in nature and causes financial damage to the environment. In the case of air pollution, harmful and foreign substances in the air reach an amount and density above normal values. Air pollution also causes climate change, which affects global warming. Particulate matter is a harmful substance that harms the health of humans and other living things, causes air pollution, increases radiation, and negatively affects cloud formation. Particulate matter is extremely small solid particles and liquid droplets suspended in the air. PM10, which is less than 10 microns in diameter, is defined as small particles that can remain in the air for a long time and settle in the respiratory tract, damaging the lungs. Many criteria affect PM10 density and changes in density. The main criteria are vehicle traffic and fuel consumption, industrialization, coal, fuel oil and wood-burning heaters, greenhouse gas impact, and unregulated urbanization. It is important to identify the underlying causes of air pollution caused by PM10. In this context, these criteria need to be evaluated to minimize the negative effects of PM10. In the study, monthly average PM10 data between 2019 and 2023 obtained from the Air Monitoring Station in Kocaeli, Türkiye are used. After determining the criteria affecting PM10, the criteria are prioritized with the Intuitionistic Fuzzy AHP (IF-AHP) method by taking expert decision-maker opinions. The proposed decision-making model aims to guide obtaining the important causes of PM10 emission in terms of danger and focusing on these causes. Additionally, PM10 data is analyzed in the context of Covid-19 and a statistical analysis is made. One-way ANOVA is used to evaluate whether there is a significant difference in the average monthly data over the years. Games-Howell test, one of the post-hoc tests, is used for differences between groups (years). The study is important in that it provides a focus on the criteria affecting PM10 with an intuitive fuzzy perspective, along with statistical analysis.

In 2011, commercial aviation contributed approximately 3.5% of global anthropogenic climate change through the emission of greenhouse gases during flight and operational non-CO2 climate effects. Over the last few years, numerous aviation-related organisations have set goals to reduce aviation’s climate impact. These goals, however, lack alignment, are poorly or ambiguously defined, or are internally inconsistent. This increases uncertainty about what aviation should work towards, how various stakeholders can contribute, and introduces problems with respect to accountability. In order to address this issue, this paper presents a comprehensive definition of a climate neutral air transport system as an “air transport system of which the climate effects of all its greenhouse gases and non-carbon dioxide effects throughout the entire life-cycle of each element of the system is balanced”. The proposed definition spans relevant system and encompasses all life cycle phases. To achieve a climate neutral air transport system by 2050, all life-cycle greenhouse gas emissions and non-CO2 climate effects remaining after in-sector reduction should be neutralised, as should all remaining non-CO2 climate forcing from emissions prior to 2050. Clarity on governance is furthermore needed, as the goal and associated targets proposed should be adopted globally.

Inhaled particulate matter (PM) is a key player in the millions of yearly deaths worldwide related to air pollution. The oxidative potential of PM provides an indication of its ability to promote an oxidative environment. When the human lungs are exposed to PM, the reactive oxygen species (ROS) generated in such oxidative environment, if excessive, may lead to cell damage via oxidative stress. Inflammation, endoplasmic reticulum stress, airway remodeling, and many different cell death modes (apoptosis, ferroptosis, pyroptosis, among others) can be triggered by oxidative stress via complex molecular pathways, which also involve the adaptive cellular response. But ROS can also directly interact with macromolecules such as proteins and lipids, as well as nucleic acids, having been reported to induce DNA damage and epigenetic modifications, which jeopardizes homeostasis. These facts have been extensively studied in in vitro models and confirmed in in vivo models.In this review, we delve beyond conventional assessments of airborne particles, discussing their oxidative potential and the PM-induced ROS-mediated cellular damage observed in in vitro models. The close link between oxidative stress and inflammation, and the manifestation of different cell death modes is highlighted by reviewing the latest literature. The effects of ROS on the balance of DNA damage and repair, carcinogenicity and epigenetics interplay are then analyzed. Finally, we expand on the latest reports on the antioxidants’ potential to counteract the deleterious effects of ROS, and disclose future perspectives for the topic.

As the demand for fossil fuels continues to rise and their availability becomes increasingly limited, it is crucial to explore innovative approaches to optimize fuel combustion in existing systems. Among various engines, diesel engines are heavily reliant on fluid motion within the engine cylinder, which plays a critical role in fuel-air mixing. This abstract focuses on the potential of dynamic mathematical model simulation for multi-compartment rotor compressed combustion engines, aiming to revolutionize power generation by enhancing fuel burning efficiency. By leveraging advanced simulation techniques, this research seeks to unlock new insights into fluid dynamics and optimize fuel-air mixing, leading to more efficient and sustainable energy utilization. Through this exploration, we aim to pave the way for groundbreaking advancements in the field of combustion engines, ultimately contributing to a greener and more sustainable future. In the realm of internal combustion engines, the fluid dynamics within the engine cylinder greatly influence the combustion processes and heat transfer. For compression ignition (C.I) engines, both the bulk gas motion and turbulence characteristics play vital roles in engine performance. This study focuses on enhancing the combustibility of the fuel-air mixture in C.I engines by modifying the engine design to induce turbulence through squish and tumble flows. The modification involves creating multiple compartments on the rotor crown, comprising three small chambers spaced 120º apart. By implementing this design, the aim is to optimize the fuel-air mixing and improve the overall combustion efficiency. Through comprehensive analysis and experimentation, we seek to revolutionize C.I engine technology and pave the way for more efficient and environmentally-friendly power generation. In this study, the performance of a compression ignition (C.I) engine with a multiple compartment rotor has been analyzed under motoring conditions using computational fluid dynamics (CFD) simulations with FLUENT software. The obtained results have been compared with those of a base C.I engine. The analysis focused on the effects of the modified engine design on the tumble ratio and squish velocity, which are important parameters for fuel-air mixing and combustion efficiency. The results indicated a significant improvement with the modified engine, with a 35% increase in tumble ratio and a 31% increase in squish velocity compared to the base engine. These findings suggest that the modified engine design has the potential to enhance fuel-air mixing and combustion performance, leading to improved overall engine efficiency. This research presents promising insights into the optimization of C.I engine design and contributes to the development of more efficient and environmentally-friendly power generation technologies..

Highly transparent, conductive nanosheets are extremely attractive for advanced optoelectronic applications. Previously, we have demonstrated that transparent, conductive Au nanosheets can be prepared by UV irradiation of Au nanoparticle (AuNP) monolayers spread on water, which serves as the subphase. In this study, we show that this UV irradiation technique can easily be extended as a nanosheet modification method by using subphases containing metal ions. That is, aqueous solutions containing Au and Ag ions are effective in modifying Au nanosheets. HAuCl4 solutions increased Au nanosheet thickness, which improved conductivity, but reduced transparency. On the other hand, use of aqueous AgNO3 and CH3COOAg solutions yielded Au-Ag hybrid nanosheets; however, their morphologies depended on the electrolytes used. Homogeneous Au-Ag nanosheets from AgNO3 and AuNPs covered with an Ag nanosheet from CH3COOAg were also produced. Further, these Au-Ag hybrid nanosheets had high conductivity without reduced transparency. Therefore, this UV irradiation method, modified by adding metal ions is quite effective at improving and diversifying properties of Au nanosheets.

Over the last few decades, there is a remarkable increase in air traffic worldwide; however, despite of rapid technological development and improved airport infrastructure, there is still an increasing number of aviation accidents and fatalities. In order to meet safety demands of Air Traffic Control (ATC), Machine Learning (ML) based aircraft conflict detection techniques are focused to predict events before they come to reality. This research presents a systematic literature review (SLR) about the applications of ML techniques in safety prediction of ATC system. Initially, the existing aircraft conflict prediction models are classified into three broad categories; logical, geometric and probabilistic. A formal process of SLR is then conducted which is initiated with preprocessing and effective searching. A series of filtering called title, abstract and objective-based are then applied to extract the most relevant articles. Detailed and critical reviews of selected articles are performed to identify challenges which are segregated into dataset, model and evaluation techniques, furthermore, the optimal solutions for each are proposed. Finally the matrices to map the identified challenged with their proposed solutions are constructed. This research serves as a foundation for future research and towards integration of ML based safety prediction techniques into modern ATC system.

The paper presents the relationship between the efficiency of the process of skin onion peeling and its effect in the form of waste. The research was carried out on a pilot test stand for onion peeling. The process variables were compressed air with a pressure of (p) and valve controlling opening time of flow (t). The experiment took into account the influence of the onion diameter (d0) and its hardness (H). The obtained results were subjected to statistical analysis. Standard deviations were of the percentage loss of onion mass in the form of the skin removed of onion peeling in the process in relation to obtained aver-age values. Tukey's multiple comparison test was performed in order to identify the importance of individual process variables on the final effect of onion peeling. This was the basis for the development of a predictive model in the form of a nonlinear regression Mp=f(p,t,d0,H), which is a mathematical description of the peeling onion skin process . Finally, the response surface area of relationship between analyzed variables was determined. The results of research showed the peeling efficiency of the onion and waste of skin mass depend on the compressed air pressure. Extending the onion blowing time does not improve the process efficiency, while the hardness and size of the onion are irrelevant to the process.

The protection of all environmental compartments (water, soil, air) is of great interest for the normal functioning of life on Earth. Namely, the environment is systematically polluted with different concentrations of physical, biological and chemical pollutants. For the purpose of environmental protection, numerous in situ and ex situ biological, chemical and physical remediation techniques have been developed. Most techniques have limitations such as high costs, processing time and environmental feasibility. In general, biological techniques have proven to be the most environmentally friendly compared to chemical and physical techniques. Furthermore, remediation is an extremely complex procedure due to the complexity of the pollutant composition. Therefore, the implementation of individual physical, biological or chemical remediation techniques is often not sufficient for adequate remediation of the polluted environment. Accordingly, for more economical and efficient environmental remediation, it is recommended to use a combination of techniques that should meet the requirements of efficiency and treatment duration. Ultimately, this short review presents a concise overview of the recent application of physical, biological and chemical remediation techniques to all compartments of the polluted environment (water, air, soil). A critical review of existing knowledge on environmental remediation through a search of relevant literature helped to assess the basic challenges and limitations that arise in the issue of environmental remediation, as well as providing recommendations and guidelines for future research.

Background: Fungi are ubiquitous microorganisms that are easily dispersed through the air. In healthcare environments, indoor air can favor the spread of healthcare-associated fungal infections, compromising mainly immunocompromised hospitalized individuals. Thus, this study aimed to evaluate the indoor air contamination in healthcare environments, investigating mainly the presence of potentially pathogenic yeasts. Methods: Indoor air samples were collected from twelve healthcare environments (hospital and medical clinics). After the growth, isolation, and purification of the yeast colonies, the isolates were identified by polymerase chain reaction using species-specific primers for yeasts of the genus Candida and sequencing of D1/D2 domains of the large ribosomal subunit (LSU rRNA). Results: Fourteen yeast species were identified, including emerging pathogens. Species of clinical importance such as Candida parapsilosis, Candida orthopsilosis, Candida glabrata, Rhodotorula mucilaginosa, and Trichosporon mucoides were present. C. Parapsilosis was the most prevalent species, followed by Rodothorula mucilaginosa. Conclusions: The present study shows that potentially fungal pathogens were present in air samples from healthcare environments, proving the role of indoor air in spreading infections. Thus, monitoring air quality in healthcare environments is a fundamental approach in developing infection control measures, especially those related to invasive fungal infections.

The increase and diversity of low-cost Air Quality (AQ) sensors, as well as their flexibility and low power consumption, offers us the opportunity to integrate them into a broad AQ wireless sensor networks with the aim of enabling real-time monitoring and higher spatial sampling density of pollution in all parts of the cities. Considering that the vast majority of the population lives in these cities and the increase in respiratory/allergic problems in a large part of the population, it is of great interest to offer services and applications to improve their quality of life. In the ECO4RUPA project we focus on this kind of service, proposing an inclusive and intelligent routing ecosystem carried out by using a network of low-cost AQ sensors with the support of 5G communications along with official AQ monitoring stations, assisted with artificial intelligence to improve the AQ monitoring data and by spatial interpolation techniques to enhance its spatial resolution. The goal of this service is to calculate healthy walking and/or cycling routes according to the particular citizen’s profile and needs. We provide and analyse the results of the proposed route planner under different scenarios (different time tables, congestion road traffic and routes) and different user’s profiles, with special interest on citizens with asthma and pregnant women, since both require special needs. In summary, our approach can lead to an approximately average reduction in pollution exposure of 17.82%, while experiencing an approximately average increase in distance travelled of 9.8 %.

Background and Objectives: The aim of this study is to investigate the diagnostic-therapeutic prob-lem of pelvic recurrence of rectum cancer, highlighting current surgical standards and the possi-ble role of the minimally invasive approach. This retrospective analysis of our surgical case study wishes to enter this debate while suggesting a possible line of action, based on the site of recur-rence. Materials and Methods: We examined, retrospectively, all the patients diagnosed, between 2008 and 2018, with cancer of the rectum at the "Pietro Valdoni" Department of Surgery and monitored their follow-up for 5 years. The sample consisted of 368 patients with rectal neoplasm, 136 females and 232 males, with an average age of 65.8 (ranging from 37 to 86). In 103 of the cases, the neo-plasm was located in the upper rectum (28%), in 119 cases in the middle rectum (32.3%), in 102 cases in the lower rectum (27.7%), in 31 cases (8.4%) at the level of the right/sigma junction and in 13 cases it was not possible to define the site with certainty (3.5%). Results: We examined all patients diagnosed with cancer of the rectum between 2008 and 2018 at the "Pietro Valdoni" Department of Surgery retrospectively and monitored their follow-up for 5 years. The sample consists of 368 patients with rectal neoplasm, 136 females and 232 males. Conclusions: The discussion remains open as to which approach is best at surgical level, whether laparoscopic, robotic or open-air. Our experience informs us that the most dangerous site remains on the anastomotic site.

Reinforcement learning is used for air combat problems in recent years, and the idea of curriculum learning is often used for reinforcement learning, but traditional curriculum learning suffers from the problem of plasticity loss in neural networks. Plasticity loss is the difficulty of learning new knowledge after the network has converged. To this end, we propose a motivational curriculum learning distributed proximal policy optimization (MCLDPPO) algorithm, through which agents trained can significantly outperform the predictive game tree and mainstream reinforcement learning methods. The motivational curriculum learning is to help the agent gradually improve their combat ability by observing the agent's unsatisfactory performance and providing corresponding rewards as a guide. Additionally, a complete tactical maneuver is encapsulated based on existing air combat knowledge, and through the flexible use of these maneuvers, some tactics beyond human knowledge can be realized. In addition, we designed an interruption mechanism for the agent to increase the frequency of decision-making when the agent faces an emergency. When the number of threats the agent receives changes, the current action will be interrupted to reacquire observations and make decisions again. Using the interruption mechanism can significantly improve the ability of the agent. To simulate actual air combat better, we built an air combat environment based on digital twin technology to create an air combat engine core such as missiles and radars. Based on this environment, we develop a distributed intelligent training system that employs Redis as the cache and obtains the data generated in the distributed environment through a multi-threaded TCP/IP protocol, which significantly increases the training data throughput and helps the agent accelerates convergence. The experimental results demonstrate that the agent can fully exploit the situational information to make reasonable decisions and affords air combat tactical adaption, verifying the effectiveness of the algorithmic framework proposed in this paper.

Modern commercial air travel connects disparate human populations with the global airline industry transporting up to 4.5 billion passengers annually in the years leading up to the COVID-19 pandemic. While such connections are convenient for commerce and tourism, air travel networks can also be efficient distributors of infectious diseases such as influenza, SARS-CoV-1, hemorrhagic fevers, and more recently SARS-CoV-2 and monkeypox. During the COVID-19 pandemic, public health agencies used multi-layered control strategies including pre-departure testing and vaccination requirements, masking, post-arrival testing, and quarantine to manage the risk of COVID-19 transmission associated with air travel. Simultaneously, the surveillance of aircraft wastewater emerged as a promising new data source to screen for SARS-CoV-2 infections, including newly emergent lineages, among international air travelers. Herein, we review the potential of aircraft wastewater for public health surveillance. The known contributing population and flight itinerary combined with the highly concentrated waste stream and convenient sampling during routine lavatory servicing make aircraft wastewater a strategic opportunity for unintrusive surveillance of the global fluxes of human pathogens. We estimate for the cases of fecal- or urine-shed pathogens, sampling from 3,500 and 1,250 flights per week, respectively, would be required to survey 10% of all global long-haul flight passengers. In the case of the United States, achieving 10% coverage of all international arrivals would require sampling from 925 and 322 flights per week, respectively. Aircraft wastewater surveillance could also be integrated with network and infectious disease models to better inform traditional public health control measures during emerging epidemics. Given the tremendous potential for public good and the massive economic costs of epidemics, governments should consider international collaboration to create a global aircraft wastewater surveillance system.

Substantial reductions of the human and economic activities like road traffic for several months in 2020 were one of the consequences of the Coronavirus disease. This unprecedented change in urban metabolism also affected temperature and air pollutants. This study investigates the effects of the first COVID-19 lockdown over 43 cities in Europe. It determines the influence of anthropogenic activities on nitrogen dioxide (NO2), ozone (O3), and particulate matter (PM2.5) as well as on land surface temperature (LST), and the surface urban heat island intensity (SUHII), using satellite, modelled, and mobility data. Our findings show that there are great temporal and spatial differences and distinct patterns between the cities regarding the magnitude of change of the variables under study. In general, the results indicate a significant decrease in NO2 concentrations in most of the studied cities compared to the reference period 2015-2019. However, reductions could not be attributed to mobility changes like less traffic at transit stations, contrary to the results of previous studies. O3 levels increased during the first lockdown mainly influenced by the decreasing NO2 concentrations. The PM pattern was inconsistent over time and space. Similar as the NO2 results, no relation to the altered mobility behavior was found. No clear signal could be detected for LST and the SUHII, likely due to dominating meteorological influences. Therefore, single city case studies may be misleading.

Keywords:

Accurate estimation of vehicle emissions is essential and can be helpful in the decision-making process. Thanks to calculation methods, it is possible to accurately estimate the emissions that result from driving a car and to determine their impact on, for example, the health of pedestrians who are on the pavement near an arterial road. Recent years have seen an increase in the use and importance of emission models, as well as vehicle traffic simulation models. Increasingly, emission models are being combined with traffic simulation models, as it is not practical to actually measure the on-road emissions of an entire fleet of vehicles over a given stretch of road. This paper provides an overview of the selected work on the topic of emission modelling and vehicle traffic simulation models. The models are distinguished according to their respective scales of accuracy, i.e., micro, meso, and macro. Selected work combining emission and traffic simulation models is also presented, as well as development trends in the field. In particular, the paper also highlights the fact of proper calibration of vehicle traffic simulation models in order to obtain the most reliable vehicle emissions results from computational models. The review of the works carried out may be helpful for future projects concerning the use of simulation tools for transport and environmental decision-makers in the area of arterial roads.

The research aims to improve some of the physical and hydro-physical properties of some Vertisols in the southern region (part of the eastern Houran Plateau) in Sweda Governorate at the south of Syria. Using different quantities of volcanic ash, soil samples were collected from the Al-Thahallah village from a depth of (0-30) cm, The experiment was designed according to the complete random design with one factor that represents the ash quantity (1.25, 2.5, 5) %, with three replicates for each treatment in addition to the control treatment a0. The experiment was carried out within the plastic pots during agricultural season 2018/2019, in which the wheat of the Sham variety 3 were cultivated as a cover plant. The results showed that the addition of volcanic ash at the quantity of 5% led to a significant increase in the infiltration rate by (328.60) %,%, where the filtration rate increased from 0.42 cm/hr -1 to 1.80 cm.h-1, as well as for each of the air porosity by (89) % and the volume of infiltrate water by (40) %, compared with the control. The above-mentioned addition also resulted in a decrease in both dry bulk density, total soil porosity and volumetric swelling coefficient by (18.60, 5.80, 314) % Respectively, compared to the control. The addition also contributed to the reduce in the weighted moisture content when saturation and the field capacity, at the level of significance of 5%. The research recommends adding volcanic ash to the soil at a quantity of 5%, and adding enhancements with volcanic ash at various levels such as organic waste.

Several studies have identified a relationship between air pollution and depression, particularly in relation to fine particulate matter (PM2.5) exposure. However, the strength of this association appears to be moderated by variables such as age, gender, genetic vulnerability, physical activity and climatic conditions, and has not been assessed at a cross-national level to date. The current study examines the association between the prevalence of depression in each country, based on the most recent Global Burden of Disease Study data, and the average national level of PM2.5 based on the World Health Organization’s database. The observed associations were adjusted for age, gender, level of physical activity, income, education, population density, climate, and type of depression. It was observed that there was a modest but significant positive correlation between PM2.5 level and the prevalence of depression even after adjusting for the above confounders. This association was more marked above a certain threshold and applied chiefly to major depressive episodes. These findings are of significant public health importance in terms of preventive strategies aimed at reducing the population-level burden of depression.

Ion Transport Membrane (ITM) is a well-developed technology for producing O₂ by separating air in its membrane. To decrease energy loss in air separation unit and to increase the overall efficiency of a power generation unit ITM is added with the gasification unit in this model. Ceramic materials are generally used to make ion transport membrane that produces oxygen by conducting oxygen ions at specified temperature. Potential advantages can be gained by integrating ITM technology with power generation units as 99% pure oxygen is produced from ITM. A salient comparison between ITM air separator combined with IGCC and cryogenic air separator combined with IGCC is done in this paper where the total power generation cycle remains same for both cases excluding the air separation units (ITM and cryogenic). Using ITM air separator is more beneficial compared to cryogenic air separation as ITM technology helps to improve IGCC overall efficiency and also reduces plant auxiliaries than that of power generation systems integrated with cryogenic.

Chronic obstructive pulmonary disease (COPD) is strongly associated with tobacco smoking and it is the increasing cause of morbidity and mortality worldwide. The prevalence of COPD among never smokers varies widely across regions, areas, and nations. COPD in smokers has been extensively explored worldwide, however, COPD in non-smokers is under-explored and there is limited data available on non-smoking COPD. We determined the role of environmental pollution and biomass fuel exposure in COPD patients who were non-smokers. We evaluated the clinical profile of non-smokers with COPD in a retrospective observational study. 180 non-smoker COPD patients were selected from the year 2016-to 2018. We found that many patients with COPD are non-smokers and the incidence is higher among the rural population, suggesting that non-smoking COPD is evolving rapidly due to biomass smoke and other environmental pollutant exposures.

Road vehicles are a large contributor to Nitrogen Oxides (NOx) pollution. The routine road-side monitoring stations, however, may underrepresent the severity of personal exposure in urban areas, because long-term average readings cannot capture the effects of momentary, high peaks of air pollution. While numerical modelling tools historically have been used to propose an improved distribution of monitoring stations, ultra-high resolution Computational Fluid Dynamics models can further assist the relevant stakeholders in understanding the important details of pollutant dispersion and exposure at local level. This study deploys a 10 cm-resolution CFD model to evaluate actual high peaks of personal exposure to NOx from traffic, by tracking the gases emitted from the tailpipe of moving vehicles being dispersed towards the roadside. The investigation shows that a set of four Euro 5-rated diesel vehicles travelling at constant speed may generate momentary road-side concentrations of NOx as high as 1.25 mg/m3, with 25% expected increase for doubling the number of vehicles and approximately 50% reduction when considering Euro 6-rated vehicles. The paper demonstrates how the numerical tool can be used to identify the impact of measures to reduce personal exposure, such as protective urban furniture, as traffic patterns and environmental conditions change.

Aircraft emissions represent a relevant amount of human induced CO2. Globally, up to 2.5 per cent of such emissions stem from the aviation industry. In order to investigate the effects within the atmosphere, realistic flight profiles are necessary to provide quantitatively tangible values of emissions. The flight profiles and the according fuel consumption can be calculated by using waypoints from flight plans and Base of Aircraft Data (BADA). This paper presents an approach to refine the fuel consumption by integrating the passenger load into the calculation. Since effects of emissions have to be assessed on a greater scale, such as on the European air traffic network, the presented approach provides cost functions for CO2 emissions for different aircraft types and load factors. The cost functions were derived by means of regression analyses of BADA based calculated flight profiles with a step size of one second. The calculations are based on real historic traffic scenarios of several days. The derived aircraft specific fuel burn coefficients enable a simple and efficient integration of CO2 estimations depending on the flight distance, load factor and aircraft type. This can be applied to large traffic scenarios to also study different set-ups such as travel restrictions, other disruptions or an alteration in the traffic system as a whole. In order to enable the assessment of further aspects of such changes to the European air traffic system at large and to foster reproducibility and comparability of related studies, we provide further general-purpose cost estimation functions for several important key characteristics. Besides fuel consumption, we develop cost estimations for air navigation fees and maintenance for conventional aircraft. Those functions are also provided for the design concept of a short-range all-electric aircraft. This propeller aircraft features game-changing technologies such as active laminar flow control, active load alleviation and advanced materials and structure concepts. The approaches discussed in this paper will focus on the generic aspects of aircraft related costs, which can be derived from general available data. For the sake of reproducibility, the results will be made publicly available.

Research have been conducted in many countries around the world to assess air quality during COVID-19 pandemic, especially during lockdown period, some of these studies found an increase or decrease in some pollutants. This paper investigates the impact of COVID-19 on seven air pollutants (i.e., PM_2.5, PM₁₀, NO₂, O₃, SO₂, H₂S, CO) from the period January 2020 to December 2020 in the State of Kuwait. Kuwait is a desert country located in the north-eastern part of the Arabian Peninsula, and the northeast of the Arabian Gulf (Persian as it is sometimes called). Several analytical methods were conducted, such as spatial analysis (spatial interpolation) to study the distribution of the studied variables. The data was also statistically analysed (time series analysis - Kernel density) to study the temporal changes. The analysis also included applying air quality index to the data. We found that concentrations for the pollutants decreased during the pandemic due to the decrease of anthropogenic sources including such as traffic and petroleum activities, but the concentration for PM_2.5 increased, mostly because of the transported dust coming with the northwest winds prevailing in Kuwait from the Arabian deserts and Iraq.

The vehicular technology has integrated many features in the system, which enhances the safety and comfort of the user. Among these features, heating, ventilation, and air conditioning (HVAC) is the only feature that maintains the set cabin air temperature (CAT). The user’s command drives the set CAT, and the thermostat provides feedback to the HVAC to maintain the set CAT. The CAT is increased by extracting the heat from the engine surface produced by the fuel combustion, whereas the CAT is reduced by the known processes of the air conditioning system (ACS). Therefore, the CAT driven by the user’s command may not be optimal, and estimating the optimal CAT is still unsolved. In this work, the user was allowed to input a range for CAT instead of a single value. Optimal HVAC criteria were defined, and the CAT was estimated by performing iterative analysis in the user-selected range satisfying the criteria. The HVAC criteria were defined based on two measurable parameters: air conditioning refrigerant fluid pressure (ACRFP) and engine surface temperature (EST) empirically defined as the vector CATOP. In this article, a NARX DL model by mapping the vehicle-level vectors (VLV) to predict the CATOP in real-time using field data obtained from a 2020 Cadillac CT5 test vehicle. Utilising the DL model, CATOP for future time steps were predicted by varying the CAT in the definite range and applying HVAC criteria. Thus, an optimal set CAT was estimated, corresponding to the optimal CATOP defined by the HVAC criteria. We performed the validation of the DL model for multiple datasets using traditional statistical techniques, namely, signal-to-noise ratio (SNR) values, first-order derivatives (FOD), and root-mean-square error (RMSE).

Background: this RCT assesses the 18 months clinical outcomes after regenerative therapy of periimplantitis lesions using either an electrolytic method (EC) to remove biofilms or a combination of powder spray and electrolytic method (PEC). Materials and Methods: Twenty-four patients (24 implants) suffering from periimplantitis were randomly treated by EC or PEC followed by augmentation and submerged healing. Probing pocket depth (PPD), Bleeding on Probing (BoP), suppuration and standardized radiographs were assessed before surgery (T0), 6 months after augmentation (T1), 6 (T2) and 12 (T3) months after replacement of the restoration. Results: Mean of PPD changed from 5.8 ± 1.6 mm (T0) to 3.1 ± 1.4 mm (T3). While BoP and suppuration at T0 was 100 % BoP decreased at T2 to 36.8 % and at T3 to 35.3 %. Suppuration could be found 10.6% at T2 and 11.8% at T3. Radiologic bone level measured from the implant shoulder to the first visible bone to implant contact was 4.9 ± 1.9 mm at me-sial and 4.4 ± 2.2 mm at distal sites (T0) and 1.7 ± 1.7 mm and 1.5 ± 17 mm at T3. Conclusions: Significant radiographic bone fill and improvement of clinical parameters were demonstrated 18 months after therapy.

TRPOMI instrument aboard Sentinel-5P is a relatively new, high-resolution source of information about atmosphere composition. One of the primary atmospheric trace gases that we can observe through it is nitrogen dioxide. By now, we were using the chemical weather model (GEM-AQ) as a mean for estimating nitrogen dioxide concentration on a regional scale. Although well established in atmospheric science, the GEM-AQ simulations were always based on emission data, which in the case of the energy sector were reported by stack owners. In this paper, we attempted to compare the TROPOMI and GEM-AQ derived VCDs over Poland with a particular focus on large point emitters. We also checked how cloudy conditions influence TROPOMI results. Finally, we tried to link the NO2 column number densities with surface concentration using boundary layer height as an additional explanatory variable

The concept of this prototype is to create a cold air film layer, in indoor side of the window. The function of this extra cold air layer is to increase the amount of window resistance and decrease its U-Value. It provide air film layer by using the same concept of desert cooler or wind catcher. They both bring the hot air from outside then let it go throw straw miost with cold water. After hot air move through straw, it would become cold, thus increase the window resistance and decrease the haet gian, therefore, decrease the cooling load. So, this window model works by heating the air in air room by sun radiation, then after a while, air pressure will rise and its volume will increase then it will impulse to wet hay, and become cold. Then there is fins to guide air flow to its correct direction, thus inner side of window will become cold, not like other type of window which when temperature rise, the inner side of window become hot. So, this window prevents heat transition and creare regenereted trubouland air flim in the inner side of the window. Using calculation to find air film characteristics and WINDOW7.7 software to calculate heat gain through window, shows that it is expected from this prototype to reduce heat gain by 6.85 % for double glazed clear window.

Today, air quality is one of the global concerns that governments are facing. One of the main air pollutants is the particulate matter (PM) that affects human health. This article presents the modeling of a purification system by means of negative air ions (NAIs) for air pollutant removal, using computational intelligence methods. The system uses a high voltage booster output to ionize air molecules from stainless steel electrodes; its particle-capturing efficiency reaches up to 97%. With two devices (5 x 2 x 2.5 cm), 2 trillion negative ions are produced per second, and the particulate matter (PM 2.5) can be reduced from 999 to 0 mg / m3 in a period of approximately 5 to 7 minutes (in a 40 x 40 x 40 cm acrylic chamber). This negative ion generator is a viable and sustainable alternative to reduce polluting emissions, with beneficial effects on human health.

Understanding the relationships between land cover/urban structure patterns and air pollutants is key to sustainable urban planning and development. In this study, we employ a mobile monitoring method to collect PM_2.5 and BC data in the city of Philadelphia, PA during the summer of 2019 and apply the Structure of Urban Landscapes (STURLA) methodology to examine relationships between urban structure and atmospheric pollution. We find that, while PM_2.5 and BC vary by STURLA class, many of the differences in pollutant concentrations between classes are not significant. However, we also find that the proportions in which STURLA components are present throughout the urban landscape can be used to predict urban air pollution. Among frequently sampled STURLA classes, gpl hosted the highest PM_2.5 concentrations on average (16.60 _± 4.29 µg/m³), while tgbwp hosted the highest BC concentrations (2.31 _± 1.94 µg/m³). Furthermore, STURLA combined with machine learning modeling was able to correlate PM_2.5 (R²= 0.68, RMSE 2.82 µg/m³) and BC (R² = 0.64, RMSE 0.75 µg/m³) concentrations with the urban landscape and spatially interpolate concentrations where sampling did not take place. These results demonstrate the efficacy of the STURLA methodology in modeling relationships between air pollution and land cover/urban structure patterns.

Air pollution contributes to a critical environmental problem in various towns and cities. With the emergence of the smart cities concept, appropriate methods to curb associated with exposure to pollutants must have been a portion of appropriate urban development policy. This study presents a technologically driven air quality solution in smart cities to advertise energy-efficient and cleaner sequestration in these areas. It aims to address the issue of how to integrate the data-based strategies and artificial intelligence into efficient public sector pollution management in smart cities as a core part of the smart city definition. Exploratory research has been used in 152 smart cities, and environmental experts contributed to this study. It further addresses the technical criteria for implementing such a framework that the public administration uses to prepare the renovation of public buildings, minimize energy use and costs, and link these smart police stations to monitor air pollution as a part of integrated cities. Such a digital transition in resource management will increase public governance's energy performance, a higher standard of operation, and a healthier environment.

Recently, we have witnessed a booming development of composites and multi-dopant metal oxides to be employed as novel photocatalysts. Yet the practical application of photocatalysis for environmental purposes is still elusive. Concerns about the unknown fate and toxicity of nanoparticles, unsatisfactory performance in real conditions, mass transfer limitations and durability issues have so far discouraged investments in full-scale applications of photocatalysis. Herein, we provide a critical overview of the main challenges that are limiting large-scale application of photocatalysis in air and water/wastewater purification. We then discuss the main approaches reported in the literature to tackle these shortcomings, such as the design of photocatalytic reactors that retain the photocatalyst, the study of degradation of micropollutants in different water matrices, and the development of gas-phase reactors with optimized contact time and irradiation. Furthermore, we provide a critical analysis of research-practice gaps such as treatment of real water and air samples, degradation of pollutants with actual environmental concentrations, photocatalyst deactivation, and cost and environmental life-cycle assessment.

: During the period of COVID-19, the Chinese government implemented a series of actions to prevent the spread of the virus. It is noticed that these preventive actions have generated positive effects on air pollution in Wuhan and Beijing. And, due to the differences in city functions, geographic locations, meteorological conditions, and preventive action details between the two cities, noticeable difference is observed on how they reduced air pollution. This unfortunate incident has become a social sample for studying the industrial and livelihood activities impact on air pollution, otherwise would be highly impossible. This paper starts from observing data from NASA's real-time fine particulate matter (PM2.5) and NO2, and comparing the air pollution in this special time domain with previous years. It is discovered that both PM2.5 and NO2 have been reduced in Wuhan, while only NO2 has significant reduction in Beijing, during the COVID-19 responses. This suggests that the human activity suppression by the COVID-19 control yields different effects on different pollutants and in different cities. Possible reasons for such effects are analysed by considering the public health control levels as well as the pollutant migration, industrial activities, and the weather conditions.

As air traffic demand grows, robust, data-driven anomaly detection methods are required to ensure that aviation systems become safer and more efficient. The terminal airspace is identified as the most critical airspace for both individual flight-level and system-level safety and efficiency. As such, developing data-driven anomaly detection methods to analyze terminal airspace operations is paramount. With the expansion of ADS-B technology, open-source flight tracking data has become more readily available to enable larger-scale analyses of aircraft operations. This paper makes a distinction between spatial metrics in ADS-B trajectory data and energy metrics derived from ADS-B trajectory data. Motivated by the limited number of approaches that simultaneously consider both spatial and energy metrics, this paper introduces the concepts of spatial anomalies and energy anomalies. In particular, it proposes a novel, unified framework for detection of spatial and energy anomalies in ADS-B trajectory data (and associated derived metrics). The framework consists of three main parts - a data processing procedure, a spatial anomaly detection method, and an energy anomaly detection method. The framework is demonstrated utilizing four months of ADS-B trajectory data associated with arrivals at San Francisco International Airport, and the relationship between the spatial and energy anomalies in this terminal airspace is explored. The results that stem from the implementation of this framework indicate that if an aircraft is spatially not conforming to an identified set of air traffic flows representing standard spatial operations, then this aircraft is more likely to experience non-conformance to standard operations in its energy metrics. Aviation operators, such as air traffic controllers, may benefit from this observation, as it may factor into decision-making in instances where there is the potential to instruct an aircraft to spatially deviate from standard operations. Additionally, this research revealed underlying differences between trajectories that are spatially nominal yet energy-anomalous and those trajectories that are spatially anomalous and energy-anomalous. Focusing solely on energy anomaly detection does not provide insight into potential spatial-related decisions that may have been made to result in off-nominal energy behavior.

Air conditioning system of electric vehicles has new change as the internal combustion engine is being replaced with electrified AC motor. With large amount of batteries installed at the bottom of frame, the conventional compressor which is belt-driven can be removed and another AC motor can play the role for air conditioning in electric vehicles. From this change, the system efficiency would be improved since it is possible to control the electrified compressor independently from traction system in contrast with the belt-driven compressor. As a result, by applying the electrified compressor for air conditioning system, the whole system can achieve better efficiency and longer driving distance, which is most important in electric vehicles. In this paper, 3-phase interior permanent magnet synchronous motor (IPMSM) was designed using lumped-parameter model and finite element method.

Air pollution has become the world’s single biggest environmental health risk of the past decade, causing about 7 million yearly deaths worldwide. One of the dominant air pollutants is fine particulate matter (PM2.5), a product of combustion. Exposure to PM2.5 has been associated with decreased lung function, impaired immunity, and exacerbations of lung disease. Accumulating evidence suggests that many of the adverse health effects of PM2.5 exposure are associated with lung inflammation and oxidative stress. While the physical structure and surface chemistry of PM2.5 are surrogate measures of particle oxidative potential, little is known about their contributions to negative health effects. In this study, we used functionalized carbon black particles as surrogates for atmospherically aged combustion formed soot to assess the effects of PM2.5 surface chemistry in lung cells. We exposed the BEAS-2B lung epithelial cell line to different soot at a range of concentrations, and assessed cell viability, inflammation, and oxidative stress. Our results indicate that exposure to soot with varying particle surface composition results in differential cell viability rates, expression of pro-inflammatory and oxidative stress genes, and protein carbonylation. We conclude that particle surface chemistry, specifically oxygen content, in soot modulates lung cell inflammatory and oxidative stress responses.

The present study investigates the relationship between the transmission of COVID-19 infections and climate indicators in Dhaka City, Bangladesh, using coronavirus infections data available from the Institute of Epidemiology, Disease Control and Research (IEDCR), Bangladesh. The Spearman-ranked correlation test was carried out to study the association of seven climate indicators, including humidity, air quality, minimum temperature, precipitation, maximum temperature, mean temperature and wind speed with the COVID-19 outbreak in Dhaka City, Bangladesh. The study found that, among the seven indicators, only three indicators (air quality, minimum temperature and average temperature) have a significant relationship with new COVID-19 cases. The results of this paper will give health regulators and policymakers valuable information to lessen the COVID-19 infection in Dhaka and other countries around the world.

A new coronavirus (SARS-CoV-2) have determined a pneumonia outbreak in China (Wuhan and Hubei) on December 2019. While pharmaceutical and non-pharmaceutical intervention strategies are strengthened worldwide, the scientific community has been studying the risk factors associated with SARS-Cov-2, to enrich epidemiological information. For a long time, before the industrialized era, air pollution has been a real and big health concern and it is today a very serious environmental risk for many diseases and anticipated deaths in the world. It has long been known that air pollutants increasing the invasiveness of pathogens for humans by acting as a carrier and making people more sensitive to pathogens through a negative influence on the immune system. Based on scientific evidences, the hypothesis that air pollution, resulting from a combination of factors such as meteorological data, level of industrialization as well as regional topography, can acts both as an infection carrier as a harmful factor of the health outcomes of COVID-19 disease has been raised recently. This hypothesis is turning in scientific evidence, thanks to the numerous studies that have been launched all over the world. With this review, we want to provide a first unique view of all the first epidemiological studies relating the association between air pollution and SARS-CoV-2. Major findings are consistent, highlighting the important contribution of air pollution on the COVID-19 spread and with a less extent also PM₁₀.

This review chronicles the indirect transmission method which seems to be overlooked by most people and makes attempts to clearly document the various transmission ways with a hope that such information may strengthen the knowledge base of researchers towards methods of eradicating the pandemic. Current knowledge of transmission and exposure of SARS-CoV-2 has been explained. Various researchers have put forward different ways of exposure and transmission. Literature does not reveal whether the indirect transmission route is the dominant one. However total lockdown could be a veritable means to reduce both direct and indirect transmission routes. In many countries where the indirect transmission has been reduced, the scourge of the virus is less. The work creates awareness on the need to watch out for those routes of transmissions that may not be popular and suggested key knowledge gaps that needs to filled.

In the present paper, a measure of the influence of irregularities of the underlying surface (for instance, the real terrain profile) on the dynamics of air flow is estimated. It is shown that these irregularities significantly perturbing the pressure, density, velocity and temperature of air flow; for perturbed pressure, density, velocity and temperature of air flow the closed formulas in the Fourier integral form are obtained. In addition, in the present paper, it is proved that due to these perturbations, at a certain altitude of the atmosphere some surface of the "sturdy wall" form appears, on which the vertical and horizontal components of the air flow velocity become infinitesimal and infinitely large, respectively.

This retrospective study evaluates the effect of a telemedicine program developed in the central Catalan region in lowering the environmental footprint by reducing the emission of atmospheric pollutants thanks to a reduction in the number of hospital visits involving journeys by road. Between January 2018 and June 2019 a total of 12,322 referrals were made to telemedicine services in the primary care centers, avoiding a total of 9,034 face-to-face visits. In total, the distance saved was 192,682 km, with a total travel time savings of 3,779 hours and a total fuel reduction of 11,754 liters with an associated cost of €15,664. This represents an average reduction of 3,248.3 g of carbon dioxide, 4.05 g of carbon monoxide, 4.86 g of nitric oxide and 3.2 g of sulphur dioxide. This study confirms that telemedicine reduces the environmental impact of atmospheric pollutants emitted by vehicles, reducing the number of journeys made for face-to-face visits and can contribute to environmental sustainability.

Microplastics (of size < 5mm) pollution in our environment is of current concern by researchers, public media and non-governmental organizations. Implications by their presence in aquatic and soil ecosystems have been well studied and documented, but less attention has been paid on airborne microplastics (MPs). Studies concerning airborne microplastics started from 2016 and only a few (n=7) have been published till date. Although, studies may increase in the following years, since air is very important for human survival. Microplastics have been observed in atmospheric fallouts in indoor and outdoor environments using a sampling or vacuum pump, rain sampler and/or particulate fallout collector. Identification and quantification have been carried out by visual, spectroscopic and spectrometric techniques. Factors such as meterological, climatic and anthropogenic influence the distribution and movement of airborne MP. Human exposure may be through inhalation or dermal route with their potential biopersistence and translocation. Ingestion may cause localized inflammation and cancer due to responses by the immune cells, especially in individuals with compromised metabolism and poor clearance mechanisms. Ecological risks involve possible contamination of the ecosystem through a dynamic relationship of MPs in soil, water and air forming a MP contamination cycle. The present review aimed at providing a comprehensive overview of current knowledge or information regarding microplastics in air, identifies gap in knowledge and give suggestions for future research.

The purpose of this study is to assess the concentration-response relations between conjunctivitis and exposure to ambient ozone. This retrospective study includes emergency department (ED) visits for conjunctivitis in Edmonton, Canada, for the period April 1992–March 2002. Daily average levels of ozone (range: 1.2–50.9, ppb), of temperature, and of relative humidity were estimated and used for the period of the study. For each of the considered exposure lags, (from 0 to 9 days), six different models were fitted to estimate the concentration-response function. The goodness of fit was assessed using the Akaike information criterion. During the period of the study, 17,211 ED visits for conjunctivitis were recorded and used. For all subjects together, a positive statistically significant association was obtained for the exposure lagged by 5 days. For female subjects, lags 1, 3, and 9 had positive statistically significant associations (lag 2 had negative associations). For male subjects, only lag 5 had a positive statistically significant association. The estimated non-linear concentration-response functions for the considered groups (all, males, females) and lags, revealed the associations along the exposure levels. The fitted shapes are described by algebraic functions and may have various forms. The estimated functions are useful to determine the risk associated with exposure to ground-level ozone.

Air quality has been a major concern throughout the world, Nigeria inclusive. The monitoring of air quality involves indoor and outdoor air quality. In this study, our concern was on indoor air quality. The aim of this study was to assess the air quality of residential homes (17), classrooms (3), hospitals (2), offices (5), Shops (2), and laboratories (5) in Akure, Nigeria in terms of formaldehyde (HCHO), total volatile organic compound (TVOC), Particulate matter (PM_1.0; PM_2.5, and PM₁₀). A Multifunction Air Detector was used for the assessment using the manufacturers’ procedures and the locations were identified using a Mini GPS. The results revealed as follows: HCHO (0.001-0.030 mg/m³), TVOC (0.003-362 mg/m³), PM_1.0 (004-014 µg/m³), PM_2.5 (006-020 µg/m³), and PM₁₀ (006-022 µg/m³). The results obtained were below the 24 h pollution recommended standards (0.1 mg/m³- HCHO; TVOC; 10-20 μ/m³ PM) of EPA and WHO. Statistically, there were correlations within the pollutants and weather. The Indoor air quality (IAQ) depicted the areas as ‘good,’ and toxicity potential (TP) were below unity. Although the locations looked safe, it is recommended that constant monitoring of the indoors should be ensured and proper ventilation should be provided.

Rapid urbanization, increasing population and increased industrialization to cater to demands of the growing population has imposed upon us a huge environmental cost. The significantly deteriorated air quality across the globe is associated with a direct and indirect impact on public health. While associated disorders such as chronic obstructive pulmonary diseases, heart failures are well documented, less is known about the biological basis of the process. We hypothesize that the worsening air quality may likely impact common systemic inflammatory processes, thus driving communicable and non-communicable diseases alike.Receptor mediated entry of particulate matter (PM2.5) results in activation of signaling cascades which culminate in production of inflammatory chemokine and cytokine responses, traversing through the blood mediating impacting not only on other organs but also dysbiosis of microflora. For the purpose of the review we choose tuberculosis (TB) as a model for communicable infectious disease and type 2 diabetes mellitus (T2DM) as a marker for non-communicable disorder. The increasing prevalence of these co-morbidities and the burdening of public health systems justifies this example. However the hypothesis may be applicable to other inflammation driven disorders also.

An important aspect of the new sustainable development goals (SDGs) is a greater emphasis on reducing the health impacts of urban ambient air pollution (AAP) in developing countries. Meanwhile, the burden of disease attributable to AAP in sub-Saharan Africa (SSA) is growing, yet estimates of its impact in the region are likely underestimated due to a lack of air quality monitoring, the paucity of epidemiological studies, and important population vulnerabilities in the region. The lack of studies in the SSA region also represents an important global health disparity and environmental justice issue because thousands of air pollution health effects studies have been conducted in Europe and North America rather than in some of the most polluted regions of the world, such as SSA. In this review, we synthesize all of the ambient air pollution epidemiological studies that have been conducted in SSA to date. We highlight the gaps in AAP epidemiological studies conducted in different sub-regions of SSA and provide methodological recommendations for future environmental epidemiology studies addressing AAP in the SSA region.

In this paper, we tackle air quality forecasting by using machine learning approaches to predict the hourly concentration of air pollutants (e.g., Ozone, PM_2.5 and Sulfur Dioxide). Machine learning, as one of the most popular techniques, is able to efficiently train a model on big data by using large-scale optimization algorithms. Although there exists some works applying machine learning to air quality prediction, most of the prior studies are restricted to small scale data and simply train standard regression models (linear or non-linear) to predict the hourly air pollution concentration. In this work, we propose refined models to predict the hourly air pollution concentration based on meteorological data of previous days by formulating the prediction of 24 hours as a multi-task learning problem. It enables us to select a good model with different regularization techniques. We propose a useful regularization by enforcing the prediction models of consecutive hours to be close to each other, and compare with several typical regularizations for multi-task learning including standard Frobenius norm regularization, nuclear norm regularization, ℓ_2,1 norm regularization. Our experiments show the proposed formulations and regularization achieve better performance than existing standard regression models and existing regularizations.

Air quality and environmental fairness have always been an area of prime interest across the globe. The significance low-cost air quality sensing and practices spikes during the time of pan-demic and epidemics when the air becomes a threat to living beings especially human beings. The gradual innovation and enrichment in low-cost air quality sensing sensors, nodes or devices, and systems are exponentially increasing for the last three decades. This work reviews the major contributions in a) low-cost scalable air quality assessment; b) low-cost air quality sensors, sensing approaches and technologies; c) low-cost state-of-the-art gas sensors fabrication methods (MEMS and CMOS); d) low-cost gas sensors measurement configurations and assemblies; and e) low-cost air quality sensors calibration and testing systems. A systematic review of past work with a goal to assist end-users, public health facilities, state agencies, researchers, scientists and air quality protection agencies has been rendered in this work. Starting from sensors electrodes to IoT based mobile smart nodes; all have been introduced in this article.