In a world where conventional sources of energy are fast depleting, the quest for alternative energy sources may hold the key for the survival of humanity. In the present work, emphasis has been given to the idea of producing energy from perovskite based solar cells. In order to bring this idea into fruition, a unique and novel nano structured perovskite material n-propyl ammonium lead chloride (C₃H₇NH₃⁺PbCl₃⁻) was prepared through a unique co-precipitation route using n-propyl amine (n-C₃H₇NH₂) and hydrochloric acid as the starting precursors with aqueous solution of Pb(CH₃COO)₂3H₂O. Finally acetic acid was added to the solution and this solution was allowed to concentrate and then gradually cooled down to room temperature. After math, the synthesized material was spin-coated on TiO₂ film to fabricate the solar cell. The device was then undergone systematic analysis using XRD, SEM, UV and Photo Conversion to get a transparent idea regarding its structural, electrical and optical properties. When experimentally applied, this perovskite-based solar cell has shown energy conversion efficiency (η) of around 6.01 % which is noticeably good. Thus it can be concluded that this material is promising for fabrication of vastly efficient solar cells. This technology can be tried in large scale as an alternative of conventional energy in the near future.

Due to an increase of the monocrystalline PV systems installations, for a drive towards the sustainable smart cities in the hot arid developing country such as Pakistan, pose challenges of the performance and degradation issues. Monocrystalline PV module efficiencies are declining and damaging under the continuous exposure to higher surface day-time temperatures in the different parts of the country. A MATLAB simulations were performed based on the validated mathematical approach. This paper investigates the hot arid surface temperature impacts on the performance of PV modules during the summer and winter seasons in Pakistan. The investigations are performed examining the power generating efficiency of the PV system. This paper also investigates the influence of installations of PV-system in the North, South, East and West regions of Pakistan. It was examined that the northern areas of Pakistan are more suitable for maintaining the long-term durability of the PV system. Investigations are performed for the peak summer and peak winter days. During summer months, cooling strategies have to be implemented to overcome the heating effects whilst reducing degradation effect on installed PV-system.

By planting LEDs on the surfaces of orifice baffles, a novel batch oscillatory baffled photoreactor (OBPR) together with polymer-supported Rose Bengal (Ps-RB) beads are used to investigate reaction kinetics of a photo-oxidation reaction between α-terpinene and singlet oxygen (1O2). In the widely used NMR data analysis for this reaction, α-terpinene and ascaridole are treated as a reaction pair, assuming kinetically singlet oxygen is in excess or constant. We have, for the first time, examined the validity of the method, discovered that increasing α-terpinene initially leads to an increase of ascaridole, indicating that the supply of singlet oxygen is in excess. Applying kinetic analysis, a pseudo first order reaction kinetics is confirmed, supporting this assumption. We have subsequently initiated a methodology of estimating the 1O2 concentrations based on the proportionality of ascaridole concentrations with respect to its maximum under these conditions. With the help of the estimated singlet oxygen data, the efficiency of 1O2 utilization and the photo efficiency of converting molecular oxygen to 1O2 are further proposed and evaluated. We have also identified conditions where further increase of α-terpinene has caused decreases in ascaridole, implying kinetically that 1O2 has now become a limiting reagent, the method of treating α-terpinene and ascaridole as a reaction pair in the data analysis would no longer be valid under those conditions.

Nowadays, with smartphones people can easily take photos, post photos to any social networks and use the photos for some purposes. This leads to a social problem that unintended appearance in photos may threaten the privacy of photographed person. Some solutions to protect facial privacy in photos have already been proposed. However, most of them rely on different techniques to de-identify photos which can be done only by photographers, giving no choice to photographed person. To deal with that, we propose an approach that allows photographed person to proactively detect whether someone is intentionally/unintentionally trying to take pictures of him/her. Thereby, he/she can have appropriate reaction to protect the privacy. In this approach, we assume that the photographed person uses a wearable camera to record the surrounding environment in real-time. The skeleton information of likely photographers who are captured in the monitoring video is then extracted to be put into the calculation of dynamic programming score which is eventually compared with a threshold for recognition of photo-taking behavior. Experimental results demonstrate that by using the proposed approach, the photo-taking behavior is precisely recognized with high accuracy of 92.5%.

This study evaluates the production of biohydrogen from agro industrial waste. The worldwide energy demand is increasing exponentially and the reserves of fossil fuels are depleting, the combustion of fossil fuels has the effect on environment because of CO2 emission. Hydrogen generation market size is forecast to cross 180 billion by 2024, according to a new research report by global market. For the production of biohydrogen. we had chosen groundnut shell as our source, using Tween80 as a surfactant we had undergone pre-treatment studies for (10min,20min,30min,40min,50min) we had estimated the content of cellulose, protein, carbohydrates at (1%,2%,3%,4%,5%) and obtained the optimum value in the form of graph. The production of hydrogen is done by using the rumen fluid of the cow and the quantity of the hydrogen produced by this process is identified by using the analytical instrument Gas Chromatography.

Bio-devices are designed to allow biological matter to perform in vitro almost the same functions it performs in vivo. Therefore, they can benefit from the specificities of such materials and are expected to perform better than traditional devices. On the other hand, the integration of biological material with electronic/electrochemical instrumentation requires careful attention and can produce unconventional results. In this paper, we describe the impedance response of an electrochemical cell that converts sunlight into electrical power. It uses the photosynthetic system known as Reaction Center, which is the core of photosynthesis in several living beings. Under illumination, an abrupt transformation drives the cell electrical response from insulator to conductor and a photocurrent is observed. The impedance spectrum shows a peculiar shape which significantly modifies with the protein activation. It has been analyzed by means of a graphical/analytical/ numerical procedure. The modelling identifies an analogue electrical circuit, whose parameters give quantitative information about the underlying process. Finally, an appropriate normalization of data is proposed which validates data in dark and light and can be useful as a fast screening of measurements.

Since a large amount of sewage sludge (WSS) has been generated daily, it is necessary to explore effective methods for utilizing WSS. Although a photo-fermentation system sometimes alters the characteristics of microbial functions, there are no attempts to perform the photo-fermentation using WSS which is regularly treated under a dark-fermentation style. In this study, the effect of photo-fermentation (photo-irradiation) on anaerobic digestion using WSS was revealed. Photo-irradiation during the anaerobic digestion of WSS significantly reduced the amount of organic acids and hydrogen sulfide and methane production was also suppressed. However, it was shown that the activity of sulfate-reducing bacteria in WSS under the light treatment increased. Photo-irradiation also stimulated the growth of green-sulfur bacteria and induced anoxygenic photosynthesis, by which the fermented samples turned green linking with the consumption of hydrogen sulfide. Finally, a dark/light switching fermentation was able to reduce only hydrogen sulfide while methane production remained the same.

The fabrication and characterisation of photo-anodes based on black-Si (b-Si) are presented using a photo-electrochemical cell in NaOH solution. Black-Si was fabricated by maskless dry plasma etching and was conformally coated by tens-of-nm of TiO2 using atomic layer deposition (ALD) with a top layer of CoO_x cocatalyst deposited by pulsed laser deposition (PLD). Low reflectivity R < % of Black-Si over the entire visible and near-IR (λ < 2 µm) spectral range is favourable in better absorption of light while an increased surface area facilities larger current densities. Photoelectrochemical performance of the heterostructured photoanode is discussed in terms of n-n junction between b-Si and TiO₂.

In this paper, first the Self-Written Waveguide (SWW) process in wet photopolymer media (liquid solutions), are examined for three examples: single-, counter-, and co-fibers exposure. Then the SWWs formed inside solid material are examined including the effects of manipulating the alignment of the fibers. In all cases high precision measurements are used to position the fiber optic cables (FOCs) before exposure using a microscope. The self-writing process is indirectly monitored by observing (imaging) the light emerging from the side of the material sample during SWW formation. In this way the optical waveguide trajectories formed in an Acrylamide/Polyvinyl Alcohol (AA/PVA) a photopolymer material (sensitized at 532 nm) are examined. First the transmission of light by this material is characterized. Then the bending and merging of the waveguides which occur are investigated. The predictions of our model are shown to qualitatively agree with the observed trajectories. The largest index changes taking place at any time during the exposure, i.e. during SWW formation, are shown to take place at the positions where the largest exposure light intensity is present. Typically, such maxima exist close to the input face and the first maximum is referred to as the location of the Primary Eye. Other local maxima also appear further along the SWW and are referred to as Secondary Eyes, i.e. deeper within the material.

Groundwater contamination by nitrate and organic chemicals (e.g. 1,4-dioxane) is a growing worldwide concern. This work presents a new approach for simultaneously treating nitrate and 1,4-dioxane, which is based on UV sensitization of nitrate and sulfite, and the production of reactive species. Specifically, water contaminated with nitrate and 1,4-dioxane is irradiated by a UV source (< 250 nm) at relatively high doses, to sensitize in-situ nitrate and generate HO•. This leads to the oxidation of 1,4-dioxane (and other organics), and the (undesired) production of nitrite as an intermediate. Subsequently, sulfite is added at an optimized time-point, and its UV sensitization produces hydrated electrons which reacts and reduces nitrite. Our results confirmed the effectivity of the proposed treatment: UV irradiation of nitrate (at > 5 mg N/L) efficiently degraded 1,4-dioxane, while producing nitrite at levels higher than 1 mg N/L (its MCL in drinking water). Adding sulfite to the process after 10 minutes of irradiation reduced the concentration of nitrite, without affecting the degradation rate of 1,4-dioxane. The treated water contained elevated levels of sulfate; albeit at much lower concentration than its MCL. Treating water contaminated with nitrate and organic chemicals (often detected concomitantly) typically requires several (expensive) treatment processes. The proposed approach may present a cost-effective alternative, employing a single system for the treatment of nitrate and organic contaminants

The multitarget therapeutic strategy, as opposed to the more traditional ‘one disease-one tar-get-one drug’, may hold promise in treating multifactorial neurodegenerative syndromes, such as Alzheimer’s disease (AD) and related dementias. Recently, combining a photopharmacology approach with the multitarget-directed ligand (MTDL) design strategy, we disclosed a novel donepezil-like compound, namely 2-(4-((diethylamino)methyl)benzylidene)-5-methoxy- 2,3-dihydro-1H-inden-1-one (1a), which in the E diastereomeric form (and about tenfold less in the UV-B photo-induced isomer Z) showed the best activity as dual inhibitor of the AD-related targets acetylcholinesterase (AChE) and monoamine oxidase B (MAO-B). Herein, we investigated further photoisomerizable 2-benzylideneindan-1-one analogs 1b-h with the unconjugated tertiary amino moiety bearing alkyls of different bulkiness and lipophilicity. For each compound the thermal stable E diastereoisomer, along with the E/Z mixture as produced by UV-B light irradia-tion in the photostationary state (PSS, 75% Z), was investigated for the inhibition of human ChEs and MAOs. The pure E-diastereoisomer of the N-benzyl(ethyl)amino analog 1h achieved low nanomolar AChE and high nanomolar MAO-B inhibition potencies (IC50s 39 and 355 nM, re-spectively), whereas photoisomerization to the Z isomer (75% Z in the PSS mixture) resulted in a decrease (about 30%) of AChE inhibitory potency, and not in the MAO-B one. Molecular docking studies were performed to rationalize the different E/Z diastereoselectivity of 1h toward the two target enzymes.

Bioelectrocatalysis has become one of important research fields in electrochemistry and provided a firm base for an important technology for application to various bioelectrochemical devices such as biosensors, biofuel cells, and biosupercapacitors. The understanding and technology in bioelectrocatalysis have been greatly improved by introducing nanostructured electrode materials and protein-engineering methods over the last few decades. Recently, the electro-enzymatic production of renewable energy resources and useful organic compounds (bioelectrosynthesis) also attracts worldwide attention. In this review, we summarize recent progress in applications of enzymatic bioelectrocatalysis.

The chlorophyll is one of the most important natural pigments used extensively in the food industry. Two important factors for the production of chlorophyll are the use of plants rich in chlorophyll and efficiency of extraction method. Present investigation was performed to compare the extraction of photosynthetic pigments by using solvents of different chemical nature. The purslane plants with different growth behavior viz. Scrollable and standing were grown under shade and sunshine stress condition. Different solvents including diethyl ether, 5% ethanol, pure acetone, 20% acetone, pure methanol and 10% methanol were used to extract chlorophyll and carotenoids from the purslane plant. The results indicated that stress, growth type and different solvents had a significant effect on the extraction of chlorophyll and carotenoids. Different trend was observed in extraction rate for chlorophylls and carotenoids. Among the solvents, pure methanol was the best for extraction of chl a. Methanol and acetone were appropriate solvents to achieve the highest amount of chlorophyll from plant tissues. Among different solvents, pure methanol for chl a, pure acetone and methanol for carotenoids were best solvent for purslane plant with a growing type scrollable of under shade.

We experimentally investigate power-sensitive photo-thermal tuning (PTT) of two-dimensional (2D) graphene oxide (GO) films coated on integrated optical waveguides. We measure the light power thresholds for reversible and permanent GO reduction in silicon nitride (SiN) waveguides integrated with 1 and 2 layers of GO. Raman spectra at different positions of a hybrid waveguide with permanently reduced GO are characterized, verifying the inhomogeneous GO reduction along the direction of light propagation through the waveguide. The differences between the PTT induced by a continuous-wave laser and a pulsed laser are also compared, confirming that the PTT mainly depend on the average input power. These results reveal interesting features for 2D GO films coated on integrated optical waveguides, which are of fundamental importance for the control and engineering of GO’s properties in hybrid integrated photonic devices.

Applied electrostatic engineering can be used to construct greenhouses that prevent entry of insect pests. Two types of electric field screen were used to exclude pests from the greenhouse: single- and double-charged dipolar electric field screens (S- and D-screen, respectively). The S-screen consisted of iron insulated conductor wires (ICWs) arrayed in parallel (ICW-layer), a grounded metal net on either side of the ICW-layer, and a direct current voltage generator. S-screens were attached to the side windows of the greenhouse to repel whiteflies (Bemisia tabaci) that approached the nets. The D-screen was installed in a small anteroom at the greenhouse entrance to capture whiteflies entering through it. The ICW-layers of the D-screen were oppositely charged with equal voltages and arrayed alternately, and an insulator board or grounded metal net was placed on one side of the ICW-layer. The ICW-layers captured whiteflies entering the electric field of the double-charged dipolar electric field. Three screens equipped with yellow or gray boards or a grounded metal net were installed in the anteroom based on the airflow inside the room, as most whiteflies were brought in by air when the door was opened. Two D-screens with boards were useful for directing the airflow toward the wall with the netted D-screen. This screen eliminated the insects and the pest-free air was circulated inside the greenhouse. The D-screen with the yellow board attracted the whiteflies and was effective for trapping them when there was no wind. Our method kept the greenhouse pest-free throughout the entire period of tomato (Solanum lycopersicum) cultivation.

In this work, the solar light-induced redox photoactivity of the ZnO semiconductor material was used to prepare at room temperature CuxO-ZnO composite catalysts with a control of the chemical state of the copper oxide phase. The preparation of Cu2(I)O-ZnO and Cu(II)O-ZnO composite catalysts was achieved by using Cu(acac)2 in THF-water and Cu(NO3)2 in water as metallic precursor, respectively. Prior to the implementation of the photo-assisted synthesis method, the most efficient photoactive ZnO material was selected among different ZnO materials prepared by the low temperature polyol method and through the precipitation method with carbonates and carbamates as precipitation agent, by taking the photocatalytic degradation of the 4-chlorophenol compound in water under simulated solar light as model reaction. The ZnO support materials were characterized by XRD, BET, TGA, SEM and TEM, and the synthesis method was strongly influencing their photoactivity in terms of 4-chlorophenol degradation and of total organic carbon removal. The most photoactive ZnO material was prepared by precipitation with carbonates and calcined at 300°C, and was taking advantage of a high specific surface area and a small mean crystallite size for achieving a complete 4-chlorophenol mineralization within 70 min of reaction, with a minimum Zn2+ released to the solution due to surface photocorrosion. Beside thermal catalysis applications, this work opened a new route for the facile synthesis of Cu2O-ZnO heterojunction photocatalysts, that could take advantage under solar light of the heterojunction built between the p-type semi-conductor Cu2O with direct visible light band gap and the ZnO semiconductor phase.

As a photo-catalytic titanium oxide film deposition process, thermal spray is hoped to be utilized practically on the condition that it is relatively easy to deposit anatase rich films. However, because of its high equipment and feedstock powder costs, it is very difficult to introduce thermal spray equipment into small companies. In this study, to develop a low cost thermal spray system, low power atmospheric suspension plasma spray equipment with titanium hydroxide suspension created by hydrolysis of titanium tetra iso butoxide using Ar, N2 as working gases. For avoiding sedimentation of the hydroxide particles in the suspension, mechanical milling of the suspension was conducted to create colloidal suspension before using it as feedstock. Moreover, an Ultrasonic wave container was used to keep the suspension particles moving while the spray process was conducted. After the film deposition, with As for the coating, anatase rich TiO2 film could be obtained. For characterization of the film, microstructure observation by optical microscope and X-ray diffraction was carried out. Consequently, by creation of colloidal suspension, deposition could be conducted without sedimentation of the hydroxide particle in the suspension during operation. Besides, it was proved the film had enough photo-catalytic property to decolor methylene-blue droplet

The per capita availability of freshwater resources on a global scale is gradually decreasing due to population growth, rapid urbanization, industrialization, and modern lifestyles. In this situation, wastewater management becomes a major concern. Conventional treatment processes used to treat wastewater discharges are not adequate for the advanced removal of pollutants, especially refractory organic pollutants, which are mainly organic compounds that are not easily biodegradable in the environment. The use of photocatalytic membrane reactors (PMRs) for tertiary wastewater treatment has attracted much interest in recent periods, and various configurations have been investigated. The performance of a PMR using an iron doped titanium photo catalyst and Polysulfone-based polymeric membrane for municipal wastewater treatment was evaluated under natural and simulated solar light. Obtained results proved that solar driven PMRs can remove organic loading (COD) with high efficiencies and may represent a suitable alternative for the tertiary treatment step of municipal wastewater.

The quartz tuning fork used as an acoustic sensor in Quartz-Enhanced Photo-Acoustic Spectroscopy gas detection systems is usually read-out by means of a transimpedance preamplifier, based on a low-noise operational amplifier closed in a feedback loop. The gain-bandwidth product of the operational amplifier used in the circuit is a key parameter which must be properly chosen to guarantee that the circuit works as expected. Here we demonstrate that, if the value of this parameter is not sufficiently large, the response of the preamplifier exhibits a peak at a frequency which does not coincide with the series resonant frequency of the quartz tuning fork. If this peak frequency is selected for modulating the laser bias current and is also used as reference frequency of the lock-in amplifier, a penalty results in terms of signal to noise ratio at the output of the QEPAS sensor. This worsens the performance of the gas sensing system in terms of ultimate detection limits. We show that this happens when the front-end preamplifier of the quartz tuning fork is based on some amplifier models that are typically used for such application, both when the integration time of the lock-in amplifier filter is long, to boost noise rejection, and when it is short, in order to comply with a relevant measurement rate.

Following the occurrence of a typhoon, quick damage assessment related to residents can facilitate quick dispatch of house repair and disaster insurance works. Employing a deep learning method, this study used aerial photos of the Chiba prefecture obtained following the Typhoon Faxai in 2019 to automatically detect and evaluate the roof damage. This study comprised three parts: training deep learning model, detecting the roof damage using trained model, and classifying the level of roof damage. The detection object comprised roof outline, blue tarps, and roof completely destroyed. The roofs were divided into three categories: roof without damage, roof with blue tarps and roof completely destroyed. the F value obtained using the proposed method was higher than those obtained using other methods. In addition, it can be further divided into 5 levels from level 0 to 4. Finally, the spatial distribution of the roof damage was analyzed using ArcGIS tools. The proposed method is expected to provide certain reference for the real-time detection of the roof damage after the occurrence of a typhoon.

This article presents, for the first time, the kinetics and the general conversion features of free radical polymerization (FRP) in a 3-component system (A/B/N), with [A] being the initiator, and [B] and [N] are additives, based on the proposed mechanism of Rahal et al. Higher FRP can be achieved by additives [B] and [N], via the dual function of (i) regeneration [A], and (ii) generation of extra radicals (R) via the radicals (S' and S) produced by N.The initiator (coumarin) shows a dual photo-oxidation and photo-reduction character for high efficacy. The FRP conversion efficacy (CE) depends not only on the property of the initiator [A], the additives [B] and [N}, but also the types of monomers. For example, when [A]=CoumC, [A]/NPG is more efficient than [A]/Iod, but revserse trend occurs in some monomers. However, 2-component systems (with CE=0% to 80%) are always less efficient than that of 3-component systems (with CE=70% to 86%, in TMPTA). Specific systems with [A]=coumarins, [B]=Iodonium salt, and N=NPG are analyzed. Analytical formulas for the role of each component concentration, light intensity and coupling rates on the conversion efficacy are derived.

Structural perturbations in the Mn4CaO5 cluster site, an oxygen-evolving complex of photosystem II, such as those induced by Ca2+/Sr2+ exchanges or Ca/Mn-removal have been known to induce long-range positive shifts (+30 mV to +150 mV) in the redox potential of the primary quinone electron acceptor plastoquinone A (QA) located 40 Å distant from the OEC. Here, we reanalyzed the crystal structure of Sr-PSII solved at 2.1 Å and compare it with the native Ca-PSII of 1.9 Å with focus on the acceptor site and report on the possible long-range interactions between the donor, Mn4Ca(Sr)O5 cluster, and acceptor sites.

This research investigates the intricate dynamics between intellectual Capital (VAIC) and the stability of banks in the evolving context of Saudi Arabia's banking sector. Against the backdrop of rapid economic reforms under Vision 2030 and the challenges imposed by the COVID-19 pan-demic, the research provides a nuanced analysis of how intellectual capital and intellectual capital's components—Human Capital Efficiency (HCE), Structural Capital Efficiency (SCE), and Capital Employed Efficiency (CEE)—affect the financial stability of Saudi banks. The research analyses a decade-long panel dataset from 2012 to 2022, utilizing both fixed effects and cross-section random effects models to discern the impact of intellectual capital on bank stability. The findings reveal a positive overall influence of intellectual capital on bank stability; however, individual compo-nents present a complex relationship, with CEE showing a positive association and HCE and SCE demonstrating unexpected negative correlations with bank stability. The research identifies lev-erage (LEV) as a significant factor negatively impacting stability. Operational efficiency (OPEF) and size (SIZE) also negatively affect stability. Surprisingly, macroeconomic indicators and bank size exhibit non-significant effects on bank stability. Similarly, the direct impact of the COVID-19 pandemic was found to be non-significant, suggesting a resilient banking environment or the presence of effective mitigating strategies. As Saudi Arabia continues its ambitious economic transformation, this research underscores the critical role of effectively managed intellectual capital in ensuring the banking sector's stability. It provides a foundation for ongoing research in this vital area.

We investigate the performance of a novel flat photovoltaic-thermal (PV-T) module under high-vacuum through a 1D numerical model based on steady-state energy balance, with the aims of optimizing the simultaneous production of thermal and electrical energy. In the proposed design, the photovoltaic (PV) cell is positioned directly above the selective solar absorber (SSA), in a multilayer or fully integrated PV-SSA structure, which allows full exploitation of spectral solar radiation. In fact, in this configuration the losses related to non-absorption of low-energy photons and thermalization, typical of a classical single-junction PV cell, are reduced. The present study is conducted as the emittance and energy bandgap of the PV layer varied, thus admitting a wide variety of materials into the analysis. The dependence of the temperature coefficient, β(%/K), on the energy bandgap of the PV cell is also included. In the last part of the work, we discuss the performance of the proposed evacuated PV-T equipped with a SSA layer and thin film solar cells, namely those made of CdTe, CdS and GaAs. Overall, the paper highlights the great advantage of using high vacuum insulation, which suppresses conductive losses, and the versatility of the proposed system, which could be adapted to the user's needs simply by choosing the appropriate material for the photovoltaic layer.

Using structured light to drive colloidal motors, due to its advantages of remote manipulation, energy tunability, programmability, and controllability of spatiotemporal distribution, has been attracting much attention in the fields of targeted drug delivery, environmental control, chemical agent detection, and smart device design. Here, we focus on studying the group control of colloidal made from a photo-responsive organic polymer molecule NO-COP (N,O-Covalent organic polymer). These colloidal motors mainly respond to the light intensity patterns. We chose a digital micromirror device (DMD) to modulate the structured light field shining on the sample, by considering its merit of fast refreshing speed, good programmability, and high-power threshold. It is found that under ultraviolet or green light modulation, such colloidal motors exhibit various group behaviors including group diffusion, group patterning, and group migration. The qualitative interpretation is also provided for these observations.

Biopolymers are of growing interest, but to improve some of their poor properties and performance, it is required the formulation of bio-based blends and/or adding of nanoparticles. For this purpose, in this work, two different metal oxides, such as zinc oxide (ZnO) and titanium dioxide (TiO2), at different concentrations (0.5, 1 and 2 %wt.) have been added in polylactic acid (PLA) and polylactic acid/polyamide 11 (PLA/PA11) blends to establish their effects on solid-state properties, morphology, melt behaviour, and photo-oxidation resistance. It seems that the addition of ZnO in PLA leads to a significant reduction of its rigidity probably due to an inefficient dispersion in the melt state, while the addition of TiO2 does not penalise PLA rigidity. Interestingly, the addition of both ZnO and TiO2 in PLA/PA11 blend has a positive effect on the rigidity because of blend morphology refinement and leads to a slight increase in film hydrophobicity. The photo-oxidation resistance of neat PLA and PLA/PA11 blend is significantly reduced due to the presence of both metal oxides, and this must be considered when designing the potential applications. The last results suggest that both metal oxides could be considered as photo-sensitive degradant agents for biopolymer and biopolymer blends.

Land degradation monitoring and assessment in the Sahel zone has relied substantially on temporal trends of remote sensing-based vegetation indices, which are proxies for the bioproductivity of the land. However, prior studies have shown that negative or positive trends in bioproductivity are not necessarily associated with degradation or improvement of land condition. In this short communication, while acknowledging the contributions of remote sensing-based indices and global-scale datasets to dismantling an outdated desertification narrative, we argue that local land users have much to contribute to our understanding of land degradation, and particularly to ensuring that scientific assessments of degradation capture variables relevant to them. We used the participatory photo elicitation method in three sites in the Senegalese Ferlo in order to elicit local pastoralists’ perspectives on land degradation and identify the indicators that they use to characterize pasture quality, while empowering them to lead the discussion. The discussion revealed indicators far beyond bioproductivity, including livestock performance as well as composition and quality of the herbaceous and woody vegetative cover, invasive species, soil quality and water availability. We found that the pastoralists’ knowledge and interest in the issue could potentially be harnessed more systematically, and at larger scales, in order to build a spatially explicit field-based knowledge base of land degradation complementary to remote sensing-based maps of trends in bioproductivity. Such a dataset could serve as a standalone product or as a reference dataset for development and validation of remote sensing-based indicators.

The kinetics and optimal efficacy conditions of photoinitiated polymerization are theoretically presented. Analytic formulas are derived for the crosslink time, crosslink depth and efficacy function. The roles of photosensitizer (PS) concentration, diffusion depth and light intensity on the polymerization spatial and temporal profiles, for both uniform and non-uniform cases, are presented . For optimal efficacy, a strategy via controlled PS concentration is proposed, where re-supply of PS in high light intensity may achieve a combined-efficacy similar to low light intensity, but has a much faster procedure. A new criterion of efficacy based on the polymerization (crosslink) [strength] and [depth] is introduced.

Stimuli-responsive polymeric materials have attracted significant attentions in a variety of high-value-added and industrial applications during the past decade. Among various stimuli, light is of particular interest as a stimulus due to its unique advantages such as precisely spatiotemporal control, mild conditions, ease of use, and tunability. In recent years, a lot of effort toward synthesis of biocompatible and biodegradable polypeptide has resulted in many examples of photo-responsive nanoparticles. Depending on the specific photochemistry, those polypeptide derived nano-assemblies are capable of crosslinking, disassembling, or morphing into other shapes upon light irradiation. In this mini-review, we aim to assess the current state of photo-responsive polypeptide based nanomaterials. First, those “smart” nanomaterials will be categorized by their photo-triggered events (i.e., crosslinking, degradation, and isomerization) which are inherently governed by photo-sensitive functionalities including o-nitrobenzyl, coumarin, azobenzene, cinnamyl, and spiropyran. In addition, the properties and applications of those polypeptide nanomaterials will be highlighted as well. Finally, the current challenges and future directions of this subject will be evaluated.

In this paper, a thermodynamic investigation is done on a Kalina-flash cycle. This work is initially validated with the Kalina cycle power plant, Wich is commissioned in Husavic. Low-temperature Kalina-flash is considered for this study. This cycle is working with the ammonia-water mixture. The Kalina-flash cycle was optimized in the view of exergy and thermal efficiency. A multi-objective genetic algorithm is used to accomplish optimization. The optimum values of the objective functions are observed to be 40.20 and 11.70% respectively. At last, The influence of the separator inlet dryness fraction, basic ammonia mass fraction, temperature and flash pressure ratio on the first and second law efficiencies are analysed.

The coombs (in Catalan comes) form an integral part of the landscape. These are small valleys, with the deepest and flattest part cultivated for agriculture. They are predominantly found in the most arid regions of Catalonia, particularly around the cities of Tarragona and Lleida. They are generally dry land areas. We propose that these coombs gained significance in the early centuries of the Middle Ages, a period marked by intense erosion. It is important to identify their locations and establish connections with medieval written documents, the settlements that thrived throughout the Middle Ages, archaeological sites such as necropolises, and the valuable data derived from to-ponymy studies. We think that understanding these coombs can greatly contribute to under-standing how the territory was organized in the Middle Ages, the extent of cultivated lands that were established, and the distribution of many settlements. Ultimately, this knowledge can aid in acquiring better understanding of the current landscape.

In this research paper a novel Ultra Violet Photo Catalyst Oxidation (UVPCO) sensor for air and surface sanitization using Common Source (CS) amplifier is presented. The ultra violet photo catalysis is the process in which the highly reactive radicals like H+, OH-and peroxides ions are produced from air in the presence of the ultra violet radiation and photo catalyst. In this process, the free radicals outbreaks the bio aerosols like bacteria, fungus and volatile organic compounds (VOCs) and destroy them. The proposed system is relies on the fast operation of PCS which operates under sub-threshold conditions and reduced computation time. The properties of common source amplifier like very high voltage gain and input output resistance increased the sensitivity as well as stability of the circuit. The system is more user friendly and the outcomes of simulation are fairly in agreement with the theoretical estimation. Keywords: bio aerosol, Photo Catalytic Oxidation (PCO), hydroxyl, hydrogen peroxide, SPICE, surface sanitizer.

This work deals with the performance evaluation of novel flat photovoltaic-thermal (PV-T) modules under vacuum. Through a 1D (dimensional) steady-state-energy-balance numerical model developed in MATLAB, two different layouts are studied: the first consisting of a photovoltaic (PV) cell installed just below the glass encapsulating the flat panel, and the second where the PV cell is placed on the selective solar absorber (SSA). In both cases the thermal and electrical efficiencies have been evaluated at different SSA operating temperatures, in the range of 323 K to 423 K. The analysis has been conducted at different energy bandgap (E_bg) of the PV cell and assuming a variable transmittance or emittance of the PV cell, depending on the design. The two systems efficiency comparison has been carried out at the same operating temperature. Overall, this work highlights the importance of high vacuum insulation, which guarantees the reduction of convective thermal losses, and shows that the maximum energy is produced for PV cells with E_bg ≈1.5-1.7 eV, depending on layout and operating temperature, by including the thermal output in the PV-T optimization. The energy and exergy efficiencies obtainable using the proposed PV-T systems are considerably improved compared to the results previously reported in the literature.

The study focused on the technical and scale efficiency of smallholder pineapple farmers in the Central Region of Ghana. The input-oriented Data Envelopment Analysis (DEA) was used to estimate technical, pure and scale efficiencies of the smallholder pineapple farmers, of which a random sampling procedure was used to select 320 respondents. The study revealed that the farmers were technically inefficient with mean technical efficiency under Constant Returns to Scale (CRS), pure efficiency under Variable Returns to Scale (VRS) and the Scale Efficiency levels of 0.505, 0.641 and 0.772, respectively, due to farmers’ inability to exploit fully the available technology while experiencing evident post-harvest losses resulting from low adoption of post-harvest technologies. Such findings are meaningful and could help the farming communities and relevant policymakers to understand the issues in farming production and hence undertake necessary actions to potentially improve farmers’ technical and scale efficiencies in the study area.

Laser-induced functionalisation using excimer laser irradiation has been widely applied to transparent conductive oxide films. However, exploring suitable irradiation conditions is time-consuming and cost-ineffective as there are numerous routine film fabrication and analytical processes. Thus, we herein explored a real-time technique to monitor the laser-induced functionalisation of transparent conductive oxide films. We developed two types of monitoring apparatus, electrical and optical, and applied them to magnetron-sputtered Sn-doped In2O3 films grown on glass substrates and hydrogen-doped In2O3 films on glass or plastic substrates using a picosecond Nd:YAG pulsed laser. Both techniques could monitor the functionalisation from a change in properties of the films on glass substrates by laser irradiation, but electrical measurement was unsuitable for plastic samples because of a laser-induced degradation of the underlying plastic substrate, which harmed proper electrical contact. Instead, we demonstrated that the optical properties in the near-infrared region were suitable for the monitoring and the changes in the optical properties were visually detected in real-time by using a near-infrared camera.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

Small and medium-sized family farms are the place of life and source of income for about half of the population. The aim of the analysis was to determine the relationship between Eco-Efficiency, Human Capital Efficiency in small and medium-sized family farms. The analyses were carried out using an economic measure (value of agricultural production per work hour calculated per 1 ha) and synthetic measures: human capital and environmental measures. The synthetic measures were determined using the CRITIC-TOPSIS method by defining weights for variables used in the synthetic measures. The analyses covered five countries, namely: Lithuania (960 farms), Moldova (532 farms), Poland (696 farms), Romania (872 farms), and Serbia (524 farms). All the countries qualified for analysis are characterised by a high fragmentation of agricultural holdings. The analyses carried out allowed us to formulate the following conclusions: the Eco-Efficiency and Human Capital Efficiency indexes increase with area for small and medium-sized family agricultural farms. An increase in the Eco-Efficiency index with an increase in farm area leads to a suspicion that the smaller the farm area is, the more extensive the agricultural production being carried out. In addition, an increase in human capital efficiency with an increase in the area of a farm indicates that there is inefficiency in the utilisation of human capital resources in the agricultural farms studied.

This work shows the potential of a new way of co-treatment of domestic wastewater (DWW) and a liquid stream coming from the thermal hydrolysis of the organic fraction of municipal solid waste (OFMSW) mediated by a mixed culture of purple phototrophic bacteria (PPB) capable of assimilating carbon and nutrients from the medium. The biological system is an open single-step process operated under microaerophilic conditions at an oxidative reduction potential (ORP) &lt; 0 mV with a photoperiod of 12/24 h and fed during the light Stage only, so the results can be extrapolated to outdoors open ponds operation by monitoring the ORP. The effluent mostly complies with the discharge values of the Spanish legislation in COD and P values (&lt;125mg/L &lt;2 mg/L), respectively, and punctually on values in N (&lt;15mg/L). Applying an HRT of 3 d and a ratio of 100:7 (COD:N), the presence of PPB in the mixed culture surpassed 50% of 16S rRNA gene copies, removing 78% of COD, 53% of N and 66% of P. Furthermore, increasing the HRT to 5 d, removal efficiencies of 83% of COD, 65% of N and 91% of P were achieved. In addition, the reactors were further operated in a membrane bioreactor, thus separating the HRT from the SRT to increase the specific loading rate. Very satisfactory removal efficiencies were achieved by applying HRT and SRT of 2.3 and 3 d, respectively: 84% of COD, 49% of N and 93% of P despite low presence of PPB due to more oxidative conditions, which anyway step-by-step re-colonized the mixed culture until reaching &gt;20% of 16S rRNA gene copies after 49 d of operation. These results open the door to scale up the process in open photobioreactors capable of treating urban wastewater and municipal solid waste in a single stage and under microaerophilic conditions by controlling the ORP of the system. This novel urban biorefinery allows reducing treatment costs of two urban wastes and embed them in the circular bioeconomy through water recycling and valorizing PPB biomass as a source of carbon, nitrogen and phosphorus.

Verteporfin, a free base benzoporphyrin derivative monoacid ring A, is a photosensitizing drug for photodynamic therapy (PDT) used in the treatment of the wet form of macular degeneration and activated by red light of 689 nm. Here, we present the first direct study of its photofragmentation channels in the gas-phase, conducted using a laser interfaced mass spectrometer across a broad photoexcitation range from 250-790 nm. The photofragmentation channels are compared with the collision-induced dissociation (CID) products revealing similar dissociation pathways characterized by the loss of the carboxyl and ester groups. Complementary solution-phase photolysis experiments indicate that photobleaching occurs in verteporfin in acetonitrile; a notable conclusion, as photoinduced activity in Verteporfin was not thought to occur in homogenous solvent conditions. These results provide unique new information on the thermal break-down products and photoproducts of this light-triggered drug.

The diffusion coefficients of ions are measured in a microchip filled with a cationic charged 3D hydrogel in order to study the effect of cationic charged 3D hydrogel on the diffusivity of ions. In this study, poly-diallyl-dimethyl-ammoniumchloride (poly-DADMAC) is used to produce a 3D hydrogel. Four different fluorophores are used in the 3D hydrogel rhodamine 6G, rhodamine-BSA, fluorescein isothio-cyanate (FITC) and FITC-BSA. The rhodamine 6G and rhodamine-BSA are positively charged (cations), while fluorescein isothio-cyanate (FITC) and FITC-BSA are negatively charged (anions). Two widely used techniques which are short time diffusivity measurement technique and long time diffusivity measurement techniques are used to measure the diffusion coefficients. For the short time measurement, Fluorescence recovery after photo-bleaching (FRAP) is used by a 3D confocal microscope. For the long time measurement, fluorescence images are taken for 11 days to observe a pure diffusivity without any convective movement. As a result, the diffusivity of the cations was found to be lower than that of the anions in the cationic charged hydrogel.

Carbon nanotubes have been attracting considerable interest among material scientists, physicists, chemists and engineers for almost 30 years. Owing to their high aspect ratio, coupled with remarkable mechanical, electronic and thermal properties, carbon nanotubes have found application in diverse fields. In this review, we will cover the work on carbon nanotubes used for sensing applications. In particular, we will see examples where carbon nanotubes act as main players in devices sensing biomolecules, gas, light or pressure changes. Furthermore, we will discuss how to improve the performance of carbon nanotube-based sensors after proper modification.

Many metrics exist for the evaluation of binary classifiers, all with their particular advantages and shortcomings. Recently an “Efficiency Index” for the evaluation of classifiers has been proposed, based on the consistency, or matching, and contradiction, or mismatching, of outcomes. This metric and its confidence intervals are easy to calculate from base data in a 2x2 contingency table, and values can be qualitatively and semi-quantitatively categorised. For medical tests, in which context the Efficiency Index was originally proposed, it facilitates communication of risk (of correct diagnosis versus misdiagnosis) to both clinicians and patients. Variants of the efficiency index (balanced, unbiased) which take into account disease prevalence and test cut-offs have also been described. The objectives of the current paper were firstly to extend the EI construct to other formulations (balanced level, quality) and secondly to explore the utility of EI and all four of its variants when applied to the dataset of a large prospective test accuracy study of a cognitive screening instrument. This showed that the balanced level, quality, and unbiased formulations of EI are more stringent measures.

This study measures the technical and scale efficiency of Micro and Small Enterprises (MSEs) and input slacks using Data Envelop Analysis (DEA) model and identifies the determinants of efficiencies of MSEs by employing ordinary least square (OLS) econometrics model. A sample of 375 randomly selected MESs are included in the study. The study found that the average technical and scale efficiency of MSEs are relatively low; technical efficiency averaged at 30 percent and 38.4 percent under constant returns to scale (CRS) and variable returns to scale (VRS) assumptions, respectively. Besides, the overall average scale efficiency score of MSEs was estimated at 77.8 percent. The highest mean technical and scale efficiencies were registered in the construction (71.8 percent) and manufacturing (85.7 percent) sectors, respectively. Whereas, the lowest technical and scale efficiency goes to urban agriculture sector and service sector, with 38.9 percent and 67.2 percent, respectively. The level of inputs, enterprise age and sector, human capital, labor productivity variables significantly affect relative technical efficiency level of MSEs with different directions while variables such as start-up capital, gender of the enterprise manager and availability of support from the government identified statistically not significant in determining the MSEs’ technical efficiency.

Jakarta is the capital city of Indonesia, which has its own problems in building transportation facilities, especially on land routes. For private vehicle users, congestion is a common thing, given the very dense number of people living in Jakarta, both natives and migrants from outside the region. And for users of public transportation services such as city transportation (angkot) and transjakarta, convenience is the main obstacle. And even though it is a public vehicle, it cannot avoid congestion because it is in one lane with private vehicles except for the transjakarta bus which has its own lane. Meanwhile, for train-based public transportation such as MRT (Mass Rapid Transit), LRT (Light rail Transit), and electric railroad (KRL), the problem is the lack of integration, namely that many stations are not yet integrated with other transportation. Various policies have been implemented to overcome these problems. This study aims to determine the level of effectiveness and efficiency of public transportation in DKI Jakarta today. The method used in this research is qualitative-descriptive through a literature review on 16 journal articles and 4 websites. The results of this study indicate that congestion is a major problem in the means of transportation in Jakarta. This is due to the increase in population due to urbanization which is also accompanied by an increase in the number of private vehicles. Therefore, to overcome this, the Jakarta Provincial Government has made improvements, reforms, and developments in public transportation. And it is hoped that people who originally used private vehicles will switch to using public transportation. But in reality, various problems in public transportation in Jakarta have not been resolved properly. Especially why traffic jams still occur?, and what are the solutions to overcome them?. It is hoped that the results of the findings of this study can be used as a reference in making or designing policies and can contribute to overcoming problems in the transportation sector, especially in the DKI Jakarta area. The limit of this research is that it only focuses on land transportation facilities in Jakarta.

Modern gas turbines firing temperatures (1500-2000K) are well beyond the maximum allowable blade material temperatures. Continuous safe operation is made possible by cooling the HP turbine first stages -nozzle vanes and rotor blades- with a portion of the compressor discharge air, a practice that induces a penalty on the cycle thermal efficiency. Therefore, a current issue is to investigate the real advantage, technical and economical, of raising maximum temperatures much further beyond current values. In this paper, process simulations of a gas turbine are performed to assess HP turbine first-stage cooling effects on cycle performance. A new simplified and properly streamlined model is proposed for the non-adiabatic expansion of the hot gas mixed with the cooling air within the blade passage, which allows for a comparison of several cycle configurations at different TIT (turbine inlet temperature) and max (total turbine expansion ratio) with a realistically acceptable degree of approximation.. The calculations suggest that, at a given max, the TIT can be increased in order to reach higher cycle efficiency up to a limit imposed by the required amount and temperature of the cooling air. Beyond this limit, no significant gains in thermal efficiency are obtained by adopting higher max and/or increasing the TIT, so that it is convenient in terms of cycle performance to design at lower rather than higher max. The small penalty on cycle efficiency is compensated by lower plant cost. The results of our model agree with those of some previous much more complex and computationally expensive studies, so that the novelty of this paper lies in the original method adopted on which the proposed model is based, and in the fast, accurate and low resource intensity of the corresponding numerical procedure: all advantages that can be crucial for industry needs. The presented analysis is purely thermodynamic, with no investigation on the effects of the different configurations on plant costs, so that future work addressing a thermo-economic analysis of the air-cooled gas turbine power plant is the next logical step.

Energy efficiency is, in principle, a simple idea: an output of human value, for example, vehicle-km traveled, divided by the needed input energy. Efficiency improvements are regarded by many as an important means of mitigating not only climate change, but also other environmental problems. Accordingly, many countries have efficiency ratings for appliances and efficiency standards for road vehicles. Despite the vast number of articles published on energy efficiency, few question whether it is a useful or accurate measure in its present form. This review addresses this lack, by a critical review of the literature, not only in energy efficiency, but in other areas of research, such as ‘energy services’, that can help broaden the scope of this idea, both geographically and conceptually. These shortcomings are illustrated in case studies of road passenger transport and buildings. The main findings are that energy efficiency inevitably has an ethical dimension, that feedbacks are more widespread than generally considered, and that conventional efficiency measures omit important energy input items, particularly those concerned with mining of the materials needed for renewable energy plants. Finally, the key results of this review are summarized, and its limitations are discussed, as is the future research needed to overcome these shortcomings.

This article presents, for the first time, the efficacy and curing depth analysis of photo-thermal dual polymerization in metal (Fe) polymer composites for 3D printing of a 3-component (A/B/M) system based on the proposed mechanism of our group, in which the co initiators A and B are Irgacure-369, and charge-transfer complexes (CTC), respectively; and the monomer M is filled by Fe. Our formulas show the depth of curing (Zc) is an increasing function of the light intensity, but a decreasing function of the Fe and photoinitiator concentrations. Zc is enhanced by the additive [B] which produces extra thermal radical for polymerization under high temperature. The heat (or temperature) increase in the system has two components : (i) due to the light absorption of Fe filler, and (ii) heat released from the exothermic photopolymerization of the monomer. The heat is transported to the additive (or co-initiator) [B] to produce extra radical R' and enhance the monomer conversion function (CF). The Fe filler leads to temperature increase, but also limits the light penetration leading to lower CF and Zc, which could be overcome by the additive initiator [B] in thick polymers. Optimal Fe for maximal CF and Zc are explored theoretically.

BODIPY dyes have recently raised attention as potential photosensitizers. In this work, commercial and novel photosensitizers (PSs) based on BODIPY chromophores (haloBODIPYs and orthogonal dimers strategically designed with intense bands in the blue, green or red region of the Visible spectra and high singlet oxygen production) were covalently linked to mesoporous silica nanoparticles (MSNs) further functionalized with PEG and folic acid (FA). MSNs of approximately 50 nm in size with different functional groups were synthesized to allow multiple alternatives of PS-PEG-FA decoration of their external surface. Different combinations varying the type of PS (commercial Rose Bengal, Thionine and Chlorine e6 or custom-made BODIPY-based), the linkage design and the length of PEG are detailed. All the nanosystems were physicochemically characterized (morphology, diameter, size distribution and PS loaded amount) and photophysically studied (absorption capacity, fluorescence efficiency, and singlet oxygen production) in suspension. For the most promising PS-PEG-FA silica nanoplatforms, the biocompatibility in dark conditions and the phototoxicity under suitable irradiation wavelengths (blue, green, or red) at regulated light doses (10-15 J/cm2) were compared with PSs free in solution in HeLa cells in vitro.

Bisphenol-A (BPA) represents an important co-monomer for obtaining polycarbonate, epoxy resins, flame retardants, in paint, and other chemicals products. Products containing BPA are widely used, and thus, we can find it in the environment: in the air, in the soil, in natural surface water and in sediments, underground water in landfills, and in wastewater. BPA disturbs human and animals’ health. This influences the enzymatic, androgenic, neurological, liver and reproductive systems at different stages of human life: like in fetal stage, children and adults’ stages. Taking these inconveniences into account, it is very important to remove BPA from water. Ultrasonic technology can be considered a verry sustainable and efficient method to remove BPA from water. The advantages of this method is easy to implement on existing water treatment and purification facilities, it does not produce residual compounds that produce sludge, the time required for degradation is of the order of 1-2 hours and the level of degradation is very high. In this work, we presented the studies on the efficiency of ultrasonics under air atmosphere on the degradation of BPA. The influence of the frequency and of some additional compounds such as carbon tetrachloride, FeSO4 7H2O (FS), and ethyl anthraquinone (EAC) was studied. Three different frequencies were used: 1146 KHz, 864 KHz, 580 KHz, at a power of 50 W. It was identified the efficiency of BPA degradation over a period of 60 minutes, with sampling every 15 minutes. Using the LC-MS/MS technique, the degradation compounds were identified that result from the application of ultrasound processes. Pathways of BPA degradation were also proposed.

The paper presents modelling of relationships between wind velocity distributions observed in Poland and technical requirements for wind power stations design. The wind velocities distributions for various locations in Poland are determined, and expressed in Weibull distribution parameters. Theoretical computations concerning the dependence of wind power station as function of wind speed and aire physical properties are presented. Conclusions important for design of power stations fitted to atmospheric conditions in Poland are given. Wind power plants have been an important source of electricity generation for many years.Wind power modelling with the use of wind speed is used to improve the accuracy of forecasts and analyses of the power production of wind farms.

Greenhouses are instrumental in the advancement of regions globally. The geometric arrangement of these structures plays a pivotal role in governing sunlight distribution, facilitating ventilation, and managing condensation. The roof's shape significantly affects energy efficiency and the accumulation of condensation water, which, when dripping onto crops, can induce diseases and diminish production. This study introduces a Matlab program designed for defining and analyzing greenhouse roof geometry, adaptable to both single-span and multi-span structures. Various roof shapes are examined, determining angles along their length to facilitate condensation droplet runoff. Furthermore, the greenhouse's energy efficiency is evaluated by analyzing diverse roof models, accounting for surface area and internal air volume. The results aim to aid in selecting the optimal greenhouse type based on climate and latitude. This study offers a valuable decision-making tool for the planning and design of agricultural structures, providing insights to enhance overall sustainability and performance in diverse environmental contexts.

The Voltammetric and polarographic methods are proposed to determine the short time corro-sion rates of brass in 1N HCl solution. It should be noted that it is also possible to determine the corrosion rates of each species present in the solution, simultaneously like Cu (II) and Zn (II) in brass. Samples extracted from bark of Babul (ESBB) is used as corrosion inhibitors. The corrosion inhibition efficiency is 96% at 24h after the test started. These results are compared with the av-erage corrosion rates obtained by using gravimetric (PIT) and some electrochemical methods i.e. galvanostatic and potentiodynamic polarization measurements.

Climate change, the scarcity of fossil fuels, technical advances in clean energy, and the volatility of crude oil prices are just a few of the factors that have prompted the world to recognize clean energy as a viable alternative to dirty energy. As part of the Paris Climate Accord of 2015, many countries agreed to change their economies to be more sensitive to climate change. Due to this Accord, which increased interest from investors and decision-makers, investments in clean energy companies have benefited [1,2]. Clean energy stocks, which are a part of the larger world of tradable reserves, might experience pricing inefficiencies. In this paper, we investigate the multifractal scaling behavior and efficiency of green finance markets, as well as traditional markets like gold, crude oil, and natural gas between January 1, 2018, and March 9, 2023, which covers periods of low volatility and financial instability (2020 and 2022 events). To test the serial dependency (autocorrelation) and the efficient market hypothesis, in its weak form, we employed the Lo and Mackinlay test and the DFA method. The empirical findings demonstrated that both periods exhibit severe multifractal and significant asymmetry, indicating that the price indices under study are not at all efficient.

This paper describe a procedure to measure experimentally the power coefficient, Cp, of winged seeds, and apply this technique to seeds from the Norway maple (Acer platanoides). We measure Cp=56.9±2% at a tip speed ratio of 3.21±0.06. Our results are in agreement with previously published CFD simulations that indicate that these seeds – operating in low-Reynolds number conditions – approach the Betz limit (Cp=59.3%) the maximum possible efficiency for a wind turbine. In addition, this result is not consistent with the recent theoretical work of Okulov &amp; Sørensen, which suggests that a single-bladed turbine with a tip-speed ratio of 3.2 can achieve a power efficiency of no more than 30%.

In this paper, we identify issues and possible solutions in the key area of large-scale antenna systems, also know as Massive Multiple Input Multiple Output (MIMO) systems. Additionally, we propose the use of Massive MIMO technology as a means to tackle the uplink mixed-service communication problem. Under the assumption of an available physical narrowband shared channel (PNSCH), the capacity of the MTC network and, in turn, that of the whole system, can be increased by grouping Machine-Type Communication (MTC) devices into clusters and letting each cluster share the same time-frequency physical resource blocks. We study the feasibility of applying sub-optimal linear detection to the problem of detecting a large number of MTC devices sharing the same time-frequency resources at the uplink of a base station (BS) equipped with a large number of antennas, M. In our study, we derive the achievable lower-bound rates for the studied sub-optimal linear detectors and show that the transmitted power of each MTC device can be reduced as M increases, which is a very important result for powerconstrained MTC devices running on batteries. Our simulation results suggest that, as M is made progressively larger, the performance of sub-optimal linear detection methods approach the matched filter bound, also known as perfect interference-cancellation bound.

The production of olives and olive oil in the Mediterranean region is one of the most important cultivation. The continuous changes of the European Common Agricultural Policy (CAP) towards strengthening the influence of market forces, has increased the necessity for assessing the efficiency of production protocols or patterns being implemented by the farmers. The case of olive trees cultivation, despite the fact that it is very important for both farmers and consumers, has not been in depth analyzed regarding the efficiency of inputs being used during the production process. This study evaluates the efficiency rates of 100 agricultural holding specialized on olive trees cultivation in Greece, by implementing a DEA input oriented model. The inputs being used are land, fertilizers, agrochemicals, labour, and energy. The output being used is the revenue of each holding. The results quantify the significant differentiation of efficiency scores, providing evidence that there is space for restructuring the production process, in order to improve efficiency and decrease by this way the production cost of inefficient farmers.

This article presents a novel sustainable business management technique, emphasizing description and estimation over the outdated profit metric. Due to the intricacies and challenges of implementing the 2019 capital management method based on capital valuation (implemented in 2020–2022), a simpler approach became essential. While it is plausible for organizations to implement capital management based on their valuation, undertaking it with no outside help presents a challenge. The new descriptive method is fundamentally distinct in that detailed monetary valuations of capitals are omitted in favor of description and estimation. This paper establishes the groundwork for applying the new approach in several stages and introduces three new management indicators—the overall accomplishment of management goals index (evaluating management efficacy), the capital level index, and the adjustment (compliance) index—replacing the profit metric. Noteworthy advantages include separating the assessment of management outcomes from the organization's condition, including human and social capital into efficiency evaluations, and removing the profit indicator for management purposes, which prevents resource waste and enhances company efficiency and effectiveness.

The efficiencies of conventional triple organic Rankine cycle (TORC) configurations are restricted by the low critical temperatures of common working fluids (＜320 °C). This paper proposes a high-temperature TORC system. A near-azeotropic mixture biphenyl/diphenyl oxide (BDO), which has stellar track record in the high-temperature ORC applications, is innovatively adopted as the top and middle ORC fluid simultaneously. The top cycle evaporation temperature is up to 400 °C in view of BDO’s high stability. Five conventional organic fluids are chosen for the bottom ORC. Fundamentals of the TORC system are illustrated, and mathematical models are built. Thermo-economic performance is investigated. The results hint that the optimal thermodynamic property is achieved on the use of benzene as the bottom fluid. The maximum thermal and exergy efficiencies are respectively 40.86% and 74.14%. The largest irreversible loss occurs inside the heat exchanger coupling the middle and bottom ORCs, accounting for above 30% of the total entropy generation. The levelized energy cost (LEC) is 0.0284 $/kWh. Given the same heat source condition, the TORC system can boost efficiency by 1.02% and drive down LEC by 0.0024 $/kWh compared with a BDO mixture-based cascade ORC.

The vehicles number continuously growing lead to increasingly intense and congested traffic and it will additionally demand the braking system, and drivers behave more aggressively and as result is required that the braking system to be durable and efficient. For this is necessary the study the braking system behavior in conditions of intense and moderate traffic to increase the safety of traffic participants, respectively to demonstrate the need for more frequent replacement of some braking system elements. Thus, on a vehicle were performed a series of successive tests, through which the degree of wear of the brake pads and discs was monitored periodically and as a result the efficiency evolution of the braking system. The tests were carried out both in laboratory (on dynamometer) and in traffic to establish the efficiency of the braking system according to some parameters considered essential. The experimental tests showed that the recommendations regarding the frequency of replacement of brake pads and disks are inconsistent with their actual wear. Therefore, the aim of this paper is the establishment of the braking system efficiency of an auto-vehicle, subject to testing depending on the auto-vehicle mass, travel speed, distance driven, and braking time, based on experimental on stand and in-traffic tests, according the road safety regulations.

At present, the health systems of many countries face complex challenges even if their priority objectives remain the same - to provide sustainable health systems at the current and the prognostic demographic changes and requirements in a health system. The quality and the efficiency of healthcare delivery and their mutual conformity have been brought to public attention. Similarly, the quality and the efficiency of an entire process depends on the instrumentation and its procurement that represents a significant economic and procedural issue in the healthcare systems for a long time. Many reports of the public procurement processes and research studies declare this fact. The primary aim of this study is to evaluate the public procurement efficiency in the health system by means of the valuation approach, or savings’ estimates that are achieved by the public procurement. The savings were defined as a percentage difference between the estimated and the final contract price. The secondary objective is to examine an influence of selected variables on a creation of savings in the public procurement process by means of a regression analysis. The researched variables are as follows: time, method, procurement, NUTS level of procurement, Common Procurement Vocabulary Code, number of offers. The analysis results showed interesting findings. The number of offers has a significantly positive impact on the savings. It means that if the number of offers increases by one unit, the savings will increase by 15.6%. Also, time variable (year) has a positive impact on the savings. Consequently, it may be assumed that the public procurement process is improving from a time perspective. It may be partially caused by the fact that a new public procurement legislative has been valid since 2015. The NUTS level has also an impact on the savings in relation to the public procurement. The public procurements which took place at the level of a state were more beneficial as the public procurements at the regional level. Also, the procurement method was statistically significant parameter of a regression analysis. The competition actions together with a negotiation process created higher savings in comparison to tenders. In case of the CPV codes, the most significant savings were achieved in the group of ‘various medicinal products’. The study’s results provide a valuable knowledge for the creators of policies and a realization of the national strategic plans within the health system. Also, these results support a creation of national and international benchmarks in this area and a networking of international partnerships in the area of a public procurement that focus on a development of methodologies and comparative platforms creation.

The continuous energy transformation processes in heating, ventilation and air conditioning systems of buildings are responsible for 36% of global final energy consumption. Tighter thermal insulation requirements for buildings have significantly reduced heat transfer losses. Unfortunately, this has little effect on energy demand for ventilation. On the basis of the First and the Second Law of Thermodynamics, the concepts of entropy and exergy are applied to the analysis of ventilation air handling unit (AHU) with a heat pump in this paper. This study aims to develop a consistent approach for this purpose, taking into account the variations of reference temperature and temperatures of working fluids. An analytical investigation on entropy generation and exergy analysis are used, when exergy is determined by calculating coenthalpies and evaluating exergy flows and their directions. The results show that each component of the AHU has its individual character of generated entropy, destroyed exergy and exergy efficiency variation. However, the evaporator of heat pump and fans have unabated quantities of exergy destruction. The exergy efficiency of AHU decreases from 45-55% to 12-15% when outdoor air temperature is within the range of –30°C…+10°C, respectively. This helps to determine conditions and components of improving the exergy efficiency of the AHU at variable real-world local climate conditions. The presented methodological approach could be used in the dynamic modelling software and contribute to a wider application of the Second Law of Thermodynamics in practice.

Load balancing, energy efficiency and fault tolerance are among the most important data dissemination issues in Wireless Sensor Networks (WSNs). In order to successfully cope with the mentioned issues, two main approaches (namely, Data-centric Storage and Distributed Data Storage) have been proposed in the literature. Both approaches suffer from data loss due to memory and/or energy depletion in the storage nodes. Even though several techniques have been proposed so far to overcome the mentioned problems, the proposed solutions typically focus on one issue at a time. In this paper, we integrate the Data-centric Storage (DCS) features into Distributed Data Storage (DDS) mechanisms and present a novel approach, denoted as Collaborative Memory and Energy Management (CoMEM), to overcome both problems and bring memory and energy efficiency to the data loss mechanism of WSNs. We also propose analytical and simulation frameworks for performance evaluation. Our results show that the proposed method outperforms existing approaches in various WSN scenarios.

Photovoltaic materials convert light into electrical voltages. So far, most research in the field are focused on how to refine/improve the existing or standard photovoltaic cells to yield more efficient electricity, to reduce weight, to make more flexible shape, or to minimize costs under standard and uniform sunlight illuminations. In this project, we explore and demonstrate a hypothesis that non-uniform light illumination photovoltages can also be generated due to photo doping induced mobile charge carrier density gradient between light and dark areas in either p-type or n-type photo doping semiconductors. The term non-uniform light illumination was coined to refer to subjecting our photo sensing thin film devices to areas of high and low intensities of light illumination simultaneously, with an intention of creating a charge density gradient and therefore a voltage. Specifically, a polymeric composite thin film composed of P3HT (p-type photo doping semiconductor) and PCBM (photo doping electron acceptor and trap) at varying p-doping levels were studied. We observed that the fabricated photovoltaic cells with about 80% PCBM doped P3HT thin film devices exhibited 0.5-1.2 volts photovoltages under non-uniform light illuminations.

Globally, anthropogenic sound and artificial light pollution have increased to alarming levels. Evidence suggests that these can disrupt critical processes that impact ecosystems and human health. However, limited focus has been given to the potential effects of sound and artificial light pollution on microbiomes. Microbial communities are the foundations of our ecosystems. They are essential for human health and provide myriad ecosystem services. Therefore, disruption to microbiomes by anthropogenic sound and artificial light could have important ecological and human health implications. In this mini-review, we provide a critical appraisal of available scientific literature on the effects of anthropogenic sound and light exposure on microorganisms and discuss the potential ecological and human health implications. Our mini-review shows that a limited number of studies have been carried out to investigate the effects of anthropogenic sound and light pollution on microbiomes. However, based on these studies, it is evident that anthropogenic sound and light pollution have the potential to significantly influence ecosystems and human health via microbial interactions. Many of the studies suffered from modest sample sizes, suboptimal experiments designs, and some of the bioinformatics approaches used are now outdated. These factors should be improved in future studies. This is an emerging and severely underexplored area of research that could have important implications for global ecosystems and public health. Finally, we also propose the photo-sonic restoration hypothesis: does restoring natural levels of light and sound help to restore microbiomes and ecosystem stability?

This data descriptor summarizes the process applied and data gathered from 50 publications/papers reporting on the use of photography generated by tourists, tour operators and members of the public, with a particular focus on the crowdsourcing of photographs through online platforms and social networking sites (SNSs) as a method of research for wildlife conservation and ecotourism. The papers were collected in a systematic literature review to inform a pilot study of the feasibility of using SNSs to crowdsource georeferenced photographs of endangered Bornean Pygmy Elephants (Elephas maximus borneensis) taken by ecotourists along the Lower Kinabatangan River region of Sabah, Malaysia. Papers were sourced using the Murdoch University Findit online-search tool to search over 100 databases, including Proquest, Scopus and Web of Science. The criteria for a paper to be included in the review (and shared via the dataset attached to this this data descriptor) were that it was peer-reviewed, published in English, between 1997 and the 31 December 2017, had the full text accessible online and reported on a study or studies that utilized photographs that tourists, tour operators and/or members of the public generated and shared via SNSs or online platforms.

Under the background that the international technological innovation environment VUCA has been intensifying and the innovation situation of Chinese manufacturing enterprises has been impacted, the innovation dilemma faced by enterprises has attracted increasing attention, while the innovation dilemma is also one of the important factors affecting the operation efficiency of enterprises. Based on the micro-data of China’s A-share manufacturing listed enterprises, this paper empirically analyzes the impact of innovation dilemmas faced by enterprises on operational efficiency (innovation dilemmas are measured by the difference when actual innovation performance is lower than expected innovation performance). The results show that the innovation dilemma of manufacturing enterprises significantly inhibits the operational efficiency of manufacturing enterprises by reducing their risk tolerance, development ability expectation and profitability. After using a series of tests, such as instrumental variable method, propensity score matching method, DID (Differences-in-Differences) and changing variable measure method, the conclusion is still robust. In addition, the inhibitory effect of innovation dilemma on enterprise operation efficiency is more obvious for private enterprises, small and medium-sized enterprises, enterprises in the ascend or decline phase, high-tech enterprises and enterprises in the eastern region. Therefore, the government should strengthen the policy support for the manufacturing enterprises in the innovation dilemma, help the enterprises to overcome the innovation bottleneck. Manufacturing enterprises themselves should enhance their innovation capabilities and strive to get rid of the innovation dilemma in order to maintain a stable footing in the fierce market competition and improve the high-quality development of China’s manufacturing industry.

The changing of banking customer preferences after Covid-19 pandemic encourages banking transformation. Neobanks emerges as innovation in banking that enter the market to compete with the incumbent banks by offering new digital experience for customer. This paper analyzes the neobanks which transformed from traditional bank, specifically its efficiency after they implement digital transformation. Efficiency is measured by using Stochastic Frontier Analysis (SFA). This study also uses Pooled Mean Group (PMG) of Panel ARDL (Autoregressive Distributed Lagged) to investigate digital transformation as one of determinants neobank’s efficiency, as well as to examine the existence of short-term and long-term relationship between digital transformation and efficiency. The SFA results show that the efficiency of the neobanks increase after they carry out digital transformation. Furthermore, from PMG Panel ARDL, it can be concluded that digital transformation is one of determinant of efficiency and there is longevity relationship between digital transformation and efficiency. In the short run, digital transformation has a significant and negative correlation with efficiency and in the long run, it has a significant positive relationship because initially digital transformation cost for operational and risk management innovation decreases the profit efficiency, but afterwards it increases the profit efficiency.

As technology continues to play a central role in shaping global industries, the performance of technology firms on the NASDAQ has significant implications for broader economic trends. Investors, facing an increasingly complex landscape, require detailed insights to make informed decisions and navigate market volatility. Moreover, amid the ongoing digital transformation, understanding the operational dynamics of technology companies is critical for policymakers and regulatory bodies to create frameworks that foster innovation while ensuring market stability. In the current context, characterized by rapid technological advancements, market uncertainties, and evolving consumer demands, the need for a comprehensive study on the operational efficiency of NASDAQ-listed technology companies is more pertinent than ever. Objective of our study is to identify relationships and patterns among selected financial metrics to assess the operational efficiency of NASDAQ-listed technology companies between 2011 to 2023. Financial metrics used in the study include following variables namely revenues, cost of goods sold, operating expenses, research, and development expenses, selling and general administrative expenses, and operating income. Johansen's cointegration methodology is employed to unveil long-term relationships and equilibrium adjustments among the considered variables. Results of our study underscore the paramount importance of efficiently managing the cost of goods sold (COGS) for achieving superior operating performance among these leading technology firms. The findings point to a nuanced interplay among these operational metrics, highlighting the interconnectedness and sustained relationships among them. This suggests that the top technology companies exhibit a sophisticated understanding of the dynamics between these variables, allowing them to navigate the complexities of the industry with strategic finesse.

"Hydrogen is an extremely promising energy carrier, poised to become a commercially viable product in the coming years. However, there are significant hurdles that need to be addressed. One such challenge is the high energy consumption during the electrolysis process, which is used to produce hydrogen. Furthermore, the co-production of CO and CO2 during steam hydrocarbon reforming adds to the complexity. Finding innovative solutions to these issues is crucial for the widespread adoption of hydrogen as a clean and efficient energy source." Simultaneously, various industries have the capability to generate hydrogen as a by-product, each with differing levels of purity. For instance, sodium and chlorine production plants have the potential to produce high-purity hydrogen. On the other hand, digester and sewage gas can yield low-purity hydrogen. In both instances, there is an economic incentive to utilize this hydrogen for energy production or to inject it into existing natural gas pipelines A brief estimation of the technical potential of utilizing hydrogen from various sources in Nigeria, specifically for fuel cell usage, has been conducted. Moreover, resource potential visualization maps have been generated to help visualize the availability and distribution of these hydrogen sources throughout the country.

Convolution, recurrent and attention-based deep learning techniques have produced the most recent state-of-the-art results in multiple sensor-based human activity recognition (HAR) datasets. However, these techniques have high computing costs, restricting their use in low-powered devices. Different methods have been employed to increase the efficiency of these techniques; however, this often results in worse performance. Recently, pure MLP architectures have demonstrated competitive performance in vision-based tasks with lower computation costs than other deep-learning techniques. The MLP-Mixer is a pioneering pure MLP architecture that produces competitive results with state-of-the-art models in computer vision tasks. This paper shows the viability of the MLP-Mixer in sensor-based HAR. Furthermore, experiments are performed to gain insight into the Mixer modules essential for HAR, and a visual analysis of the Mixer’s weights is provided, validating the Mixer’s learning capabilities. As a result, the Mixer achieves an F1 score of 97%, 84.2%, 91.2% and 90% on the PAMAP2, Daphnet Gait, Opportunity Gestures and Opportunity Locomotion datasets, respectively, outperforming state-of-the-art models in all datasets except Opportunity Gestures.

In recent years, exterior-rotor brushless DC motors have become increasingly popular in robotics applications due to their compact shape and high torque density. However, these motors were originally used for continuous operation in drones. For applications such as exoskeletons, prostheses, or legged robots, short bursts of high power are often required. Unfortunately, vendors do not typically provide data on the motors' performance under these conditions. This paper presents experimental data on the torque-speed relationship, efficiency, and thermal responses of one of the most widely used outrunner-type brushless motors across its full operating range, including high-power, short-duration operation. The results of this study can inform the selection and design of actuators for a range of robotics applications, particularly those that require high power output for brief periods of time.

Ethylene is an ideal CO2 product in an electrocatalytic CO2 reduction reaction (CO2RR), which has high economic value. In this paper, Al–doped octahedral Cu2O (Al–Cu2O) catalyst was synthesized by a simple wet chemical method. The selectivity of CO2RR products was improved by doping Al onto the surface of octahedral Cu2O by regulating the Al content. The Al–Cu2O was used as an efficient electrocatalyst for CO2RR with selective ethylene production. The Al–Cu2O exhibited a high Faradic efficiency (FEC2H4) of 44.9% at -1.23 V (vs. RHE) in CO2 saturated 0.1 M KHCO3 electrolyte. Charge transferring from Al atom to Cu atom take place after Al doping in Cu2O, thereby optimizing the electronic structure, which facilitates CO2RR to ethylene production. The DFT calculation showed that the Al–Cu2O catalyst can effectively reduce the adsorption energy of the *CHCOH intermediate and promote the mass transfer of charges, thus improving the FEC2H4. After Al doping into Cu2O, the center of d orbitals shift positively, which makes the d–band closer to the Fermi level. Furthermore, the density of electronic states increases, which was conducted to the interaction between Cu atoms and intermediates, thus accelerating the electrochemical CO2 reduction process. This work proved that the metal doping strategy can effectively improve the catalytic properties of Cu2O, thus providing a useful way for CO2 cycling and green production of C2H4.

The paper is based on the research project P2Endure funded within the H2020-EE-2016-2017 call. The main aim of the research is to propose innovative solutions for deep renovation that are applicable and replicable for the widest range of building typologies, from public to residential and historic buildings. In this paper, the methodology adopted to perform the energy analyses and to verify the achievement of the expected targets in terms of savings is defined, based on a range of real case studies. The main aim is to promote a guideline for designers showing specific instruments to perform towards the attainment of the 60% threshold of the energy savings giving advice on how to further improve the energy performance of the buildings, basing on the overview of the energy analyses run for similar cases.

The design of highly efficient sensitizers is one of the most significant areas in dye-sensitized solar cell (DSSC) research. We have studied a series of benzothiadiazole-based D-π-π-A organic dyes, putting emphasis on the influence of the donor moiety on the DSSC’s efficiency. Using linear response time-dependent density functional theory (TDDFT) with the CAM-B3LYP functional different donor groups were characterized in terms of electronic absorption spectra and key photovoltaic parameters. As a reference a dye has been considered which has a benzothiadiazole fragment linked via thiophene rings to a diphenylamine donor and a cyanoacrylic acid acceptor. The different systems are first studied in terms of individual performance parameters, which are eventually aggregated into the power conversion efficiency. Here only the amino-substituted species shows a modest increase, whereas the dimethylamino case even shows a decrease.

The thermal insulation properties of building walls are critical to the overall energy efficiency and comfort of a building. One important factor that can affect these properties is the type of bricks used in construction. Bricks can vary in their geometry and thermal coefficient, which can impact their ability to transfer heat through the wall. The geometry of a brick can affect its thermal properties by altering the amount of air trapped within it and the surface area available for heat transfer. Hollow bricks or those with complex geometries may have lower thermal conductivity than regular solid bricks due to the air pockets trapped within them. Conversely, larger surface areas on the exterior of the brick can increase heat transfer. The thermal coefficient of clay, a common material used in brick production, is another important factor. Clay has a relatively low thermal conductivity, meaning it is a poor conductor of heat. However, the quality of the clay, as well as the firing temperature and duration used in brick production, can impact its thermal coefficient. Higher firing temperatures and longer firing times can result in a more compact and dense clay brick, which can improve its thermal properties. In summary, the thermal insulation properties of building walls can be significantly affected by the type of bricks used in their construction. It is important to consider the geometry and thermal coefficient of the bricks when designing a building to achieve the desired level of thermal insulation. By selecting bricks with appropriate properties, designers can help to improve the energy efficiency and comfort of the building while reducing its environmental impact.

Zinc oxide (ZnO) has been widely studied over the last decade for its remarkable properties in optoelectronic and photovoltaic devices because of its high electron mobility and excitonic properties, probably the broadest range of nanostructured forms, and their ease and low cost of synthesis by a wide variety of methods. The volume of recent work on ZnO nanostructures and their devices can potentially overshadow significant developments in the field. Therefore, there is a need for a concise description of the most recent advances in the field. In this review, we focus on the effect of ZnO nanostructure morphologies on the performance of ZnO-based solar cells sensitized using methylammonium lead iodide perovskite. We present an exhaustive discussion of the synthesis routes for different ZnO nanostructure morphologies, ways to control the morphology, and the impact of morphology on the photo-conversion efficiency of a given PSC.

Here is analysed the process of water re-injection in the two hydrocarbon reservoirs/fields in the Upper Miocene sandstone reservoirs, located in the western part of the Sava Depression (Croatia). Namely, those are the "A" field with "L" reservoir and the "B" field with "K" reservoir. Both currently produce hydrocarbons using a secondary recovery method, i.e. water injection (in fact re-injection of the field waters). Three regional reservoir variables had been analysed, namely porosity, permeability and injected water volumes. The number of data was small in all three cases. For porosity: reservoir “L” included 25 data, reservoir “K” 19 data; for permeability: reservoir “L” 10 data, reservoir “K” 18 data; for injected volumes of water: reservoir “L” 10 data; reservoir “K” 3 data. It defined selection of mapping algorithms mostly designed for small datasets (less than 20 points), i.e. Inverse Distance Weighting, Nearest and Natural Neighbourhood. Additionally, the Ordinary Kriging was used, but only with jack-knifed variograms, producing many “artificial points”. Results are extensively tested, using cross-validation and shape recognitions, and the Inverse Distance Weighting method is described as the most appropriate approach for mapping permeability and injected volumes in both reservoirs (“K” and “L”). The Kriging could be slightly outlined as the best approach for porosity. Obtained maps made possible application of the modified geological probability calculation as tools for prediction of successfulness of future injection (probability of 0.56). Consequently, results made possible to plan future injection more efficiently, with smaller injected volumes and same of higher hydrocarbon recovery. That could prevent useless injection, decrease number of injection wells, and save energy and funds invested in such processes.

Based on rapeseed plantation biodiesel production system requires transportation of goods, like raw materials, machines and tools, and products between various conversion stages of agricultural as well as industrial subsystems. Each transportation step requires consumption of some energy. This consumption, decreases the net amount of energy delivered out of the biofuel production system, and consequently decreases energetic efficiency of the system. The present work deals with computer modelling of the influence of energy consumed on those transport routes on the energetic efficiency of production system. The effects caused by variation of several parameters like fuel consumption and load capacity of transportation means, size of plantation, distribution and sizes of individual fields, distances between fields, as well as plantation yield, and finally the distance between plantation and the industrial facility are studied using the numerical model developed

The power generation from hydroelectric plants has increased worldwide, contributing to the participation of the renewable sources to the energy matrix. In the semiarid Brazilian Northeast (NEB), thousands of small dams have been built over time as a solution for water supply. Although incompatible with hydropower generation due to the conflict with human water supply in the region, small reservoirs accumulate water and hydraulic energy at high altitudes. In this work, simulations were performed to assess how the arrangement of various sized reservoirs impact the power demand for water distribution in the Banabuiú River Basin – BRB (19,800 km²), Brazil. The power required to pump water from all 1,405 reservoirs to the districts is 6.5 GWh/year, whereas in the scenario with the 12 larger strategic reservoirs only, the power demand reaches 45.3 GWh/year. Although representing roughly 60% of the water availability of the BRB and being able to supply all the districts, the Arrojado Lisboa reservoir alone would demand 195 GWh/year to supply water to the entire basin, i.e. 30 times the power required in the real reservoir arrangement. By storing water at high altitudes and distributing it spatially, the small reservoirs increase the energy efficiency on the water distribution system.

Most European cities are characterized by very large areas, often formed by buildings with low quality, from a series of point of view. The possibility of renovating them is strategic to improve both the quality of life and to the possibility of economic recovery for building companies. In the last decades, the attention of the scientific community has been addressed to the energy renovation, thanks to the strong activities of the European Community in this field. However, since a relevant part of the EC territory is at risk of earthquake, the possibility to combine both energy and seismic renovation actions may be strategic for many countries. In particular, Italy and Romania are linked by a common social tradition that springs from the Roman Empire. Nowadays, this link is stronger, thanks to common interests in social, cultural and business fields. Therefore, the investigation of possible synergies for seismic and energy renovation strategies may be really interesting for both countries. This paper represents the first step in this direction. After an overview of regulations and common practices for buildings with reinforced concrete structures, in both states, some key combined renovation interventions will be described and discussed, as well as advantages and perspectives of integrated renovation approaches.

Device-to-device (D2D) communication is an essential part of the future fifth generation (5G) system that can be seen as “network of networks”, consisting of multiple seamlessly integrated radio access technologies (RATs). Public safety communications, autonomous driving, social-aware networking, and infotainment services are example use cases of D2D technology. High data rate communications and use of several active air interfaces in the described network create energy consumption challenges for both base stations and the end user devices. In this paper, we review the status of 3GPP standardization and define a set of application scenarios. We use the recent models of 3GPP Long Term Evolution (LTE) and WiFi interfaces in analyzing the power consumption both from the infrastructure and user device perspectives. The results indicate that the number of active interfaces should be minimized.

Creating transgenic insects is a key technology in insect genetics and molecular biology. A widely used instrument in insect transgenesis is the piggyBac transposase, resulting in essentially ran-dom genomic integrations. In contrast, site-specific recombinases allow the targeted integration of the transgene construct into a specific genomic target site. Both strategies, however, often face limitations due to low transgenesis rates. We aimed to enhance transgenesis rates by utilizing a capped mRNA as a source of transposase or recombinase instead of a helper plasmid. A system-atic comparison of transgenesis rates in Aedes mosquitoes, as models for hard to transform in-sects, showed that suppling piggyBac transposase as mRNA increased the average transfor-mation efficiency in Aedes aegypti from less than 5% with the plasmid source to about 50% with mRNA. Similar high transformation activity was observed in Ae. albopictus with pBac mRNA. No efficiency differences between plasmid and mRNA were observed in recombination experi-ments. Furthermore, a codon-optimized version of piggyBac transposase delivered as plasmid didn’t improve the transformation efficiency in Ae. aegypti or the agricultural pest D. suzukii. We believe that the use of mRNA has strong potential for enhancing pBac transformation efficiencies in other mosquitoes and important agricultural pests such as tephritids.

The first two decades of the 21st-century have seen the emergence of the modern citizen science movement, increased demand for niche eco and wildlife tourism experiences, and the willingness of people to voluntarily share information and photographs online. To varying extents, the rapid growth of these three phenomena has been driven by the availability of portable smart devices, access to the Web 2.0 internet from almost anywhere on the planet, and the development of applications and services, including social media/networking sites (SNSs). In addition, the number of peer-reviewed publications that explore how text and images shared on SNSs can be data-mined for academic research has surged in recent years. This systematic quantitative review has two goals. The first goal is to provide an oversight of how the photographs that ecotourists share online are contributing to wildlife tourism research. The second goal is to promote the emerging photovoice technique as a theoretical context for social research based on the photographs and comments that ecotourists share on SNSs. From the perspectives of community benefits, conservation behaviours, and environmental education, there are many similarities between authentic ecotourism experiences and quality ecological citizen science programs. Much of the literature regarding the theory and practice of citizen science reports on the difficulties of attracting, training, motivating and retaining community members. The synthesis of this review is that crowdsourcing wildlife and tourism data from comments and photographs that ecotourists share on SNSs is a credible method of research that provides a self-replenishing pool of citizen scientists.

Various implementations of the Move with Interleaving transform are discussed in this paper, with the transformation itself explained briefly at first. The transform has an expected time complexity of O(n), where n represents the length of the sequence being transformed. The importance of implementation also grows as the sequences become longer. The paper explains three different implementations: the first uses the standard vector, the second employs a lookup table, and the third utilises a dynamic linked list with a pool of released records. The experiments were conducted on 32 greyscale raster images of various contexts and sizes. All three solutions were implemented in both C++ and Java, and then executed on three different platforms: a personal computer running MS Windows and Linux, and a Raspberry Pi 2 with Linux. The implementation based on the dynamic linked list was the fastest, and outperformed the vector-based implementation by more than 1800%. While direct comparisons between results on the Raspberry Pi and those on the modern personal computer may not be straightforward, a consistent pattern prevails: the dynamic linked list implementation outperformed the other two consistently, and the C++ code was faster than the code written in Java. The difference was most evident on the Raspberry Pi.

ABSTRACT"In the realm of the industrial complex, a pressing concern lies in optimizing resource utilization and enhancing energy efficiency. This critical issue finds strong support from a variety of government programs, strategies, and regulatory documents. To effectively tackle this challenge and revolutionize petrochemical production, it is imperative to establish and develop innovative mechanisms. One such mechanism involves harnessing the power of automation and advanced Industry 4.0 technologies to streamline production processes. By doing so, we can unlock the full potential of these systems, driving operational efficiency, conserving valuable reserves, and propelling innovation within the petrochemical industry."The article delves into an in-depth analysis of the prominent trends in the application of the "Industry 4.0" concept within the petrochemical industry. It sheds light on the various factors that impact the efficiency of organizing production systems. Additionally, the article identifies the primary avenues that drive the advancement and enhancement of production organization practices. Moreover, the article explores the fundamental tools employed for process improvements and highlights the significance of process automation in petrochemical plants. By examining these key aspects, it aims to provide valuable insights and recommendations for leveraging Industry 4.0 technologies to optimize production processes in the petrochemical industry..The study focuses on examining and evaluating various systems and technologies that contribute to the optimization of production processes within the petrochemical industry. Specifically, it delves into the implementation and benefits of the just-in-time system, the 5S system for workplace rationalization, as well as different information systems including ERP systems and CALS-technologies. By exploring these systems and technologies, the article aims to identify the advantages of automating production processes within the petrochemical complex. This analysis will unveil the potential benefits such as improved efficiency, reduced waste, enhanced productivity, streamlined operations, and increased overall competitiveness. Through this research, we aim to shed light on the value of these automation solutions and their impact on driving the petrochemical industry towards greater success.

The limited availability of water resources worldwide presents obstacles, to the progress of ag-riculture. This situation calls for the implementation of water saving technologies to address these challenges effectively. The quest for technologies that conserve water in agriculture, par-ticularly within the context of cotton production, is related to the study of the impact of drought on the growth, leaf surface area, accumulation of dry matter, boll number, and productivity. The benefits of local drip irrigation have been established. Various models and strategies for opti-mizing and improving the efficiency of how we use water for irrigation purposes. In a market driven economy the effective utilization of water assetsis closely linked to the improvement of managing mineral nutrients. To enhance both the quantity and quality of production, nitrogen is the key factor element that plays a role in the process. The formation of highly efficient cotton crops by adapting the growing technology to the specific soil-climatic conditions of the area, in-cluding controlling nitrogen fertilizing and irrigation, is the primary method to achieve con-sistent harvests. The results of irrigation with water deficit and feeding plants with different fer-tilizer rates are presented. This matter is presently significant, in achieving dependable crop harvests supporting the economic growth of farms and safeguarding the well being of agricul-tural environments.

Water deficit greatly affects global crop growth and productivity, particularly in water-limited environments like upland rice cultivation, leading to reduced grain yield. Plants activate various defense mechanisms during water deficit, involving numerous genes and complex metabolic pathways. Exploring orthologous genes, linked to enhanced drought tolerance, can aid functional validation in target species using genomic data from model organisms. Here, we studied the OsCPK5 gene in upland rice, an AtCPK6 ortholog from A. thaliana, by overexpressing it in the BRSMG Curinga cultivar. Transformants were assessed under two conditions: water deficit applied 79 days after seeding, lasting 14 days, followed by 7 days of irrigation at 80% field capacity. Physiological data and samples were collected at R3, R6, and R8 stages. GM plants consistently exhibited higher OsCPK5 gene expression across stages, peaking during grain filling. During this phase, GM plants displayed reduced stomatal conductance, photosynthetic rate, and increased water use efficiency compared to non-GM plants under drought. GM plants also exhibited higher filled grain percentage in both irrigation conditions. Their drought susceptibility index was 0.9 times lower than NGM plants, and they maintained a higher chlorophyll a/b index, indicating sustained photosynthesis. NGM plants under water deficit exhibited more leaf senescence, while OsCPK5-overexpressing plants retained green leaves. Overall, OsCPK5 overexpression induced diverse drought tolerance mechanisms, hinting at potential for future development of more drought-tolerant rice cultivars.

The predominance of traffic lights in urban settings often induces fluctuations in traffic patterns and energy utilization among vehicles. To counteract the adverse effects of traffic lights on the energy efficiency of electric vehicles (EVs), a Multi-Intersections-Based Eco-Approach and Departure strategy (M-EAD) is proposed. This strategy aims to enhance vehicle energy efficiency, traffic flow, and battery longevity, all while upholding satisfactory driving comfort. The M-EAD strategy unfolds in two distinct stages: the optimization of an eco-friendly green signal window and the refinement of speed trajectories. The initial stage tackles the optimization of traffic light green signal windows, underpinned by the minimization of travel delays via solving the shortest path problem. In the subsequent stage, a receding horizon framework takes center stage, leveraging an iterative dynamic programming algorithm to tackle the speed optimization challenge. The objective here is to curtail energy consumption and reduce battery wear by finding an optimal speed trajectory. Furthermore, the real-world efficacy of this approach is substantiated through on-road vehicle tests, attesting to its viability in actual road scenarios.

This study rolls out a robust framework relevant for simulation studies through the Generalised Autoregressive Conditional Heteroscedasticity (GARCH) model using the rugarch package. The package is thoroughly investigated, and novel findings are identified for improved and effective simulations. The focus of the study is to provide necessary simulation steps for volatility estimation that involve "background (optional), defining the aim, research questions, method of implementation, and summarised conclusion". The method of implementation is a workflow that includes writing the code, setting the seed, setting the true parameters a priori, data generation process and performance assessment through meta-statistics. This novel, easy-to-understand steps are demonstrated on financial returns using illustrative Monte Carlo simulation with empirical verification. Among the findings, the study shows that regardless of the arrangement of the seed values, the efficiency and consistency of an estimator generally remain the same as the sample size increases. The study also derived a new and flexible true-parameter-recovery measure which can be used by researchers to determine the level of recovery of the true parameter by the MCS estimator. It is anticipated that the outcomes of this study will be broadly applicable in finance, with intuitive appeal in other areas, for volatility estimation.

Energy savings have been a major driver for improving building airtightness in the last period. Air infiltration has an important influence on energy efficiency and significantly influences the indoor air quality and pollutant distribution in residential buildings. Pressure difference lead to air permeability through the building envelope via cracks and un-controlled air leaks, which increase not only energy consumption, also cause noise from the outside and entering particles harmful to human health. Therefore, the issue of airtightness of the building envelope has been included in the standards and regulations. Building airtightness is influenced by various design parameters such as window/wall ratio, type of joinery, size of usage area, wall material and the insulation application also the quality of workmanship. In this study, the airtightness performance of 43 different residentials in Balıkesir was deter-mined by the BlowerDoor test measurement and in the context of airtightness the architectural design parameters impact was investigated. The air exchange rate (n50) values of 43 residences were obtained between 1.94 - 49.02 h-1 and compared with the existing standards. In addition, “usage area” was determined as the most effective parameter, followed by the size of the usage area, the transparency rate of the facades, the wall material type and the insulation status.

To sustain and advance the development of our laboratory, it is imperative for the laboratory 1 personnel to consistently deliver high-quality products and services that meet customer expectations. 2 The progress of productivity and the pace of technological advancements result in constant evolution 3 of measurement procedures, analytical techniques, and overall work methods. Our research within 4 the Neutron Activation Analysis (NAA) laboratory is aimed at contributing to the establishment of 5 quality assurance that complies with the ISO 17025 standard. As such, the laboratory implements 6 quality-oriented approaches to foster a culture of continuous improvement in its detector operations 7 and enhance customer satisfaction.

Growing water shortages for large regions of the arid regions of the world, are likely to become more recurrent as climate change impacts grow. Countries across the world are facing water security difficulties that stem from population growth, urbanization, and rapid industrialization. The use of behavioral nudges methods implemented to encourage a socially desired behavior at a low to zero cost, has been an effective method at reducing water consumption in places where they have been deployed. For example, studies in California USA, Barcelona Spain, and Australia indicate that adoption of nudges give significant positive results in water consumption reduction. We describe some of the barriers that make it difficult to implement behavioral nudges to address the water crises in Sub-Saharan Africa (SSA). We investigate the literature available in Sub-Saharan Africa and discover that the application of behavioral nudges has been sparingly used for reasons that are not obvious at first glance. Second, we find that the potential impediments to the use of behavioral nudges in SSA to be awareness, inadequate access to science and technology, political systems that are poorly suited for implementing nudging, abundance of multiple ethnic groups that speak different languages, along with other barriers that could challenge implementation of behavioral nudges. In light of those barriers, we present a conceptual model with a potential to address these barriers to behavioral nudging a workable solution in SSA.

The specialisation and intensification in agriculture have increased the productivity but have also led to the spread of monocultural systems, simplifying production and reducing genetic diversity. The purpose of this study was to propose crop diversification as a tool to increase biodiversity and achieve sustainable and resilient intensive agriculture, particularly in areas with water scarcity. In this paper, a combined Life Cycle Assessment (LCA) and Life Cycle Costing (LCC) was applied to evaluate the environmental and economic sustainability of a differentiated system of cultivation (pomegranate, almond and olive), according to modern intensive and superintensive cropping systems. Based upon the results obtained, it is deduced that pomegranate cultivation generated the highest environmental load, followed by almond and olive. From the financial analysis, it emerged that almond is the most profitable, followed by pomegranate and olive.

This study was carried out to evaluate the impact of Amegilla calens bee on fruit and seed yields of G. hirsutum in an experimental field, in September 2018 and 2019. The experiments were carried out on 540 flowers divided in four treatments: 120 flowers accessible to all visitors; 120 flowers bagged to avoid all visits; 200 flowers protected and uncovered when they were opened, to allow A. calens visits; 100 flowers bagged then uncovered and rebagged without the visit of insects or any other organism. Bees daily rhythm of activity, its foraging behaviour on flowers, its pollination efficiency, the fruiting rate, the number of seeds per fruit and the percentage of normal seeds were evaluated. Results indicate that among 11 insect species recorded on flowers, X. olivacea ranked second and harvested nectar. Throughout the pollination efficiency of a single flower visit, X. olivacea provoked a significant increase of the podding rate, the mean number of seeds per pod, the percentage of normal seeds and the mean weight of a seed by 39.48 %, 18.19 %, 49.62 % and 31.53 % respectively. The conservation and installation of X. olivacea nests close to P. vulgaris fields is recommended to improve its pod production and seed quality.

Nowadays, some coffee production centers are still classification manually, so it requires a very long time, a lot of labor, and expensive operational costs. Therefore, the purpose of this research was to design and performance of the coffee bean classifier that can accelerate the process of classification beans. The classifier used consists of three main parts, namely the frame, driving force, and sieves. Research parameters include classifier work capacity, power, specific energy, classification distribution and effectiveness, and efficiency. The results showed that the best operating conditions of the coffee bean classifier was found at a rotational speed of 91.07 rpm and a 16° sieves angle with a classifier working capacity of 38.27 kg/h, the distribution of the seeds retained in the first sieve was 56.77 %, the second sieves was 28.12%, and the third sieves was 15.11%. The efficiency of using a classifier was found at a rotating speed of 91.07 rpm and a sieves angle of 16°. This classifier was simple in design, easy to operate, and can sort coffee beans into three classification, namely small, medium, and large.

This paper is about energy as viewed through an integrated model that links energy with environment, technology and urbanisation as related areas. Our goal is to empirically investigate the (in)efficient energy use across 30 developed OECD member states during the period from 2001 to 2018. For that purpose, we set up an output-oriented BCC data envelopment analysis that employs a set of input variables with non-negative values to calculate the efficiency scores on minimising energy use and losses as well as environmental emissions. We develop a couple of baseline models for primary energy and secondary energy (electricity) in which we find that countries have mean inefficiency margins of 16.1 per cent for primary energy and from 10.8 to 13.5 per cent for electricity. Then, we extend the baseline models by adding environment as an important closely related concept and confirm the consistency of the baseline findings. In the context of this analysis, however, the inefficiency scores, on the one hand, point out to a mismatch in the utilisation of the inputs to produce efficiency but, on the other hand, they uncover a hidden potential to increasy efficiency through re-allocation under constant inputs.

Inappropriate use of fertilizers is one of the major production constraints in sesame. Studies to optimize the use of N fertilizer on sesame were conducted at Humera Agricultural Research Center (HuARC) under rain fed and irrigation conditions. Thirteen (13) N doses were evaluated in a Randomized Complete Block Design (RCBD) during 2016, 2017 and 2018. In the rain fed condition; results showed higher number of days to 50% flowering on the higher N application. The 31-121.5 kg N ha-1 have scored higher seed yield, where the lower (18 kg N ha-1) and higher (156 kg N ha-1) N doses scored lower seed yield. In the irrigation condition; higher N application rate prolonged the flowering time to some extent and days to 90% maturity was reduced as N rate increased. Heavier seed weights and maximum seed yield were recorded on 64 and 75 kg N ha-1 and the lower N doses scored low seed yield. Agronomic efficiency of N fertilizer (N-AE) was higher on 64 kg N ha-1 under both growing conditions. The partial budget analysis revealed that 64 kg N ha-1 (rain fed) and 75 kg N ha-1 (irrigation) had the higher net profit, MRR and residual ranking. Therefore, for the greater sesame productivity 64 kg N ha-1 has to be recommended for rain fed and 64 to 75 kg N ha-1 for the irrigated sesame.

The results from laboratory tests and field tests, available in the open literature for over ten years, despite the announcement of high efficiency translating into increased energy efficiency and such significant ecological advantages, have not so far resulted in widespread use of fuel performance catalysts (FPC) on a global scale. Wishing to explain why the above situation occurred and to verify the operation of catalytic additives for fuels; this article presents the results of research on the effect of using catalytic additives for fuel in a brand new diesel engine. The article contains an analysis of the results of exhaust gas emission tests from the Doosan MD196TI engine. During the tests, the engine was fueled with a typical diesel fuel and the same fuel with the a catalyst additive. The catalyst was added to the liquid fuel in the form of a commercially available product distributed by ProOne company under the name FMAX. The research was carried out in the form of a test, much more developed than the approval test on a stationary braking station in accordance with the requirements of ISO 8178. The article is concluded with a comparative analysis of exhaust gas emission results illustrating the effects of a catalyst in the form of reduction of solid particles, carbon monoxide, hydrocarbons and a slight increase in nitrogen oxide emissions. In addition, the effect of the catalyst depends on the product of thermal (brake) efficiency of the engine and the calorific value (CV) of the fuel used.

This paper presents a review of the electrical heating method for heavy oil recovery based on past, current, and future prospects of electrical heating. Heavy oil is one of the potential crude oil used as a link to reduce the crisis of light oil used today. The obstacle of heavy oil is a high viscosity and density in which thermal injection is a method for heavy oil recovery, but it results in economic and environmental issues. Electrical heating is one of the thermal methods by transferring heat into the reservoir. The basic process of electrical heating is to increase the mobility of the oil. Because the temperature rises, it can reduce oil viscosity and makes it easier for heavy oil to flow. The past and current developments have been carried out to fill up the gap of electrical heating projects. The future prospects must meet energy efficiency, and the excessive heat will damage formation that must be tackled in the future prospect. the works adopt several electrical heating projects and applications in the world where the works give a brief future prospect of electrical heating.

With an increasing demand for quality of care and lower costs, hospitals are looking for industry-based methods to improve efficiency in their processes. This study aims to reduce waste in a public hospital in Mexico by improving the medical supply process for the operating room. To this end, a lean healthcare (LH) implementation following the DMAIC approach (Define-Measure-Analyze-Improve-Control) is carried out. We analyze the value stream of the supply process, including main surgical procedures and their related medical supplies, and identify different causes of inefficiency, which are evaluated and controlled through different tools, including a value stream map, Kanban, and the 5S program. As a result, five types of waste were reduced. Over-processing requests were reduced by 15.3%, defective identification numbers were reduced by 46.5%, redundant processing was improved by 94.8%, near 2.8% of the unnecessary inventory was reduced, and transportation waste was reduced by up to 16.7%. Finally, the lead-time for the main supplies was reduced by 33 days. This work demonstrates that LH and DMAIC are effective in reducing waste and are highly conducive to improving sustainability in healthcare processes. Moreover, it provides practical insights for practitioners regarding the implementation of LH in public hospitals in developing countries.