The creation of nano-zero-valent iron (nZVI) by implementing plant extracts is an environmentally friendly process. High antioxidant capacity and phenol content indicated the possibility of oak-nZVI synthesis using oak leaf extract as a stable material with minimal agglomeration. Simultaneously removal of Cd and phosphates and Ni and phosphates was optimized by a statistically designed experiment with a definitive screening design. In terms of significance, 4 input parameters on process productivity were monitored: initial metal concentration (1 - 9 mgL-1), initial ion concentration (1- 9 mgL-1), pH value (2 - 10) and oak-nZVI dosage (2 - 16 ml). Phosphate removal efficiency, in the presence of cadmium, was the most influenced by oak-nZVI dose and cadmium concentration, while pH gave three statistically significant interactions with oak-nZVI dosage, cadmium concentration, and phosphate concentration. Phosphate removal efficiency, in the presence of Ni, is the most influenced by nickel concentration, phosphate concentration, pH, two-factor interaction between nZVI dose and Ni concentration, and quadratic phosphate interaction. The process optimization yielded the highest simultaneous removal efficiency of 98.99% and 87.30% for cadmium and phosphate ions, respectively. Also, the highest simultaneous removal efficiency of nickel and phosphates ion was 93.44% for 96.75%, respectively. The optimization process fits into the confidence intervals, confirming the assumption that the adopted regression model describes the process well. This work demonstrated an enormous potential and prosperous application for the Cd(II), Ni(II), and phosphate removal from water matrices.

Using analysis methods such as Rutherford backscattering Spectrometry, scanning electron microscopy, X-ray diffraction, and Raman spectroscopy, the diffusion behavior of iodine in micro/nano-porous graphite under high-temperature conditions was studied. The results indicate that iodine diffusion leads to the contraction of graphite microcrystals, a decrease in interlayer spacing, and an increase in defect density, resulting in a reduction in microcrystal size. Upon diffusion of iodine out of iodine-loaded graphite, the microcrystal size of the graphite increases, the interlayer spacing appears to return to the initial state, and the defect density decreases. By comparing the iodine diffusion performance of nanoporous graphite G400 and G450 with microporous graphite G500, it was determined that nanoporous graphite exhibits better inhibition of iodine diffusion compared to microporous graphite. Studying the diffusion behavior of iodine in micro/nano-porous graphite has significant academic significance and engineering value for the screening, design, and performance optimization of nuclear graphite.

In this work the effect of recycled concrete aggregate modified with mineral admixtures and Nano-silica on the mechanical properties and performance of the concrete was investigated after curing in tap water for 28 and 90 days. The compressive, ƒc, indirect tensile, ƒt, and flexural, ƒb, strengths for cured concrete specimens were measured and concrete strength ratios were analyzed. The water and rapid chloride permeability were measured. SEM analysis of microstructure was, also, investigated. The coarse aggregates used were dolomite (control) and recycled concrete aggregate with the incorporation of different mineral admixtures including ground granulated blast slag and granite as well as Nano-silica. It was found that, the slump values of the dolomite concrete decreases compared with recycle aggregate concrete. The results indicate that, the concrete mix containing recycle aggregate have the highest compressive strength, tensile strength and flexural strength compered to concrete mix containing dolomite aggregate. As far as the compressive strength is concerned, the addition 1 % NS and 15 % of slag improved the physico-mechanical properties of the recycled aggregate concretes compared to the other mixes after curing in tap water.

Tissue engineering and regenerative medicine has gradually evolved as a promising therapeutic strategy to the modern healthcare of the aging and diseased population. In this study, we developed a novel nano-fibrous scaffold and verified its application in the critical bone defect regeneration. The metformin-incorporated nano-gelatin/hydroxyapatite fibers (NGF) was produced by electrospinning, cross-linked, and then characterized by XRD and FTIR. Cytotoxicity, cells adhesion, cell differentiation, and quantitative osteogenic gene and protein expression were analyzed by bone marrow stem cells from rat. Rat forearm critical bone defect model was performed for the in vivo study. The nano-gelatin/hydroxyapatite fibers (NGF) were characterized by their porous structures with proper interconnectivity without significant cytotoxic effects; the adhesion of bone marrow stem cells on the nano-gelatin/hydroxyapatite fibers (NGF) could be enhanced. The osteogenic gene and protein expression were upregulated. Post implantation, the new regenerated bone in bone defect was well demonstrated in the NGF samples. We demonstrated that the metformin-incorporated nano-gelatin-hydroxyapatite fibers greatly improved healing potential on the critical sized bone defect. Although metformin-incorporated nano-gelatin/hydroxyapatite fibers had advantageous effectiveness during bone regeneration, further validation is required before it can be applied to clinical applications.

Phytophthora. infestans is a well known late blight causing oomycetes pathogen. It evolves and adapts to the host background and new fungicide molecules rapidly within a few years of their release, may be due to the predominance of transposable elements in its genome. Frequent and huge applications of fungicides cause environmental concerns. Here we developed target specific RNA interference based molecules, that are capable of effectively reducing the late blight infection. cDNA microarray expression data was used for the selection of genes involved in the early stage of infection process, sporulation etc. The in vitro synthesis of double stranded RNA molecule, targeting SDH, EF-1α, GPI-HAM344, PLD-3 and HSP-90 encoding genes revealed the reduction in growth, sporulation and symptom expression, which were subsequently assessed by culture bioassay, detached leaf assay and topical application methods. The multiple genes targeted dsRNA nano clay sprayed plants showed enhanced disease resistance (4% disease severity) and least sporulation (<1x103), compared to naked dsRNA spray. Use of nano clay was assumed to be involved in the effective delivery, protection and boosting the action of RNAi in potato plants. A significant difference in the growth, sporulation count, disease severity and reduced expression of the genes and confocal microscopy imaging authenticates the effects of SIGS on late blight disease progression. Our research demonstrated that topical dsRNA nano clay spray under the open-air environment could be an alternative to chemical fungicides and transgenic approaches as a novel plant protection strategy for late blight in an environmentally friendly manner.

Currently, metal nanoparticles have varied uses for different medical, pharmaceutical, and agricultural applications. Nano-biotechnology combined with green chemistry has great potential for the development of novel and necessary products that benefit human activities, while encourages the reduction of hazardous reagents for nanoparticle production. Green chemistry has an important role due to its contribution to unconventional synthesis methods of gold and silver nanoparticles from plant extracts, which have exhibited antimicrobial potential among other outstanding properties. Biodiversity-rich countries need to collect and convert knowledge from biological resources into processes, compounds, methods, and tools, which need to be achieved along with sustainable use and exploitation of biological diversity. Therefore, this review focuses on the importance of metal nanoparticles, the use of plant extract for their synthesis as well as other available methods, and the relevant antimicrobial activity that can be exploited in a sustainable model of agricultural management through a modern nanotechnological approach.

Porosity in plasma sprayed coatings is vital for most engineering applications. It is either advantageous or disadvantageous depending on the functionality of the coating and the immediate working environment. Consequently, the formation mechanisms and development of porosity has been extensively explored to find out modes of controlling porosity in plasma sprayed coatings. In this work, a comprehensive review of porosity on plasma sprayed coatings is established. The formation and development of porosity on plasma sprayed coatings are governed by set spraying parameters. Optimized set spraying parameters have been used to achieve the most favorable coatings with minimum defects. Even with the optimized set spraying parameters, defects like porosity still occur. Here, we discuss other ways that can be used to control porosity in plasma sprayed coating with emphasis to atmospheric plasma sprayed chromium oxide coatings. Techniques like multi-layer coatings, nano-structured coatings, doping with rare earth elements, laser surface re-melting and a combination of the above methods have been suggested in adjusting porosity. The influences of porosity on properties of plasma sprayed coatings and the measurement methods of porosity have also been reviewed.

Traditional silicon binary circuits continue to face challenges such as high leakage power dissipation and large area of interconnections. Multiple-Valued Logic (MVL) and nano-devices are two feasible solutions to overcome these problems. In this paper, we present a novel method to design ternary logic circuits based on Carbon Nanotube Field Effect Transistors (CNFETs). The proposed designs use the unique properties of CNFETs, e.g., adjusting the Carbon Nanotube (CNT) diameters to have the desired threshold voltage and have the same mobility of P-FET and N-FET transistors. Each of our designed logic circuits implements a logic function and its complementary via a control signal. Also, these circuits have a high impedance state which saves power while the circuits are not in use. We show a more detailed application of our approach by designing a two-digit adder-subtractor circuit. We simulate the proposed ternary circuits using HSPICE via standard 32nm CNFET technology. The simulation results indicate the correct operation of the designs under different process, voltage and temperature (PVT) variations. Moreover, we designed a two-digit adder/subtractor and a power efficient ternary logic ALU based on the proposed gates. Simulation results show that the two-digit adder/subtractor using our proposed gates has 12X and 5X lower power consumption and PDP (power delay product) respectively, compared to previous designs.

Metal and alloy toughening was the core and long-term research direction in materials filed. As grain size had bimodal distribution, micro/nano-structured alloys presented excellent comprehensive mechanical properties, and this had become one of the research hotspots and developing trends in the field of nanotechnology. In-situ tensile test was a direct and effective method to study the deformation mechanism of materials, which revealed the multiple mechanisms responding to feature grain sizes and provided reliable experimental means and research technique. Research on development of in-situ technique and its applications in mechanical properties was reviewed in this paper according to the recent advances on the modern mechanical properties for high strength and high plasticity alloy at home and abroad. The disadvantages of the present study of preparation methods and investigation techniques for high-performance alloy had been concluded. Finally, the development prospects of high strength and high plasticity alloy materials were analyzed.

With the increasing demand for energy worldwide, researchers from different fields have been striving to improve the sustainability and proper utilization of energy resources. Passive radiative cooling, as a natural energy transport method, can achieve cooling without additional external energy input. This review provides a comprehensive examination of passive radiative cooling, including its fundamental theories and latest development. A particular emphasis is placed on the diverse range of fields where passive radiative cooling has been applied, notably including but not limited to construction and architecture. The current state of applications, potential challenges that may arise with wider adaption and promising research directions for each field are thoroughly discussed. This review underscores the universal applicability and feasibility of passive radiative cooling and contributes to its future development by identifying promising areas for further exploration.

This study investigates the contribution of nano-alumina (nA: 1-3wt.% binder) to the performance of silica fume (SF-10%) blended mortar in ternary blended mortar. The fresh (workability, setting time) and hardened properties (compressive strength and thermal resistance (300 °C for 1 h)), were examined. Nano alumina (nA) contributed positively to the consistency of SF blended mortar such that similar workability could be achieved with OPC when 3% nA was added. The initial and final setting time of 180 and 220 mins were recorded in SF blended mortar and reduced by 18.4 and 21.8%, respectively by adding 3%nA. The optimum mixture that contained 10%SF and 2%nA had 3-d and 28-d compressive strengths of 28 and 43.2 MPa. In the absence of nA, this reduced by 14.3% and 29.4% while it reduced by 25.2% and 16.7%, respectively in OPC mortar. The main products characterizing SF-nA ternary blended binder with dense microstructural density were nepheline and tobermorite. Besides, it is more susceptible to carbonation despite its superior performance in thermal resistance when compared to SF blended and OPC mortars.

This paper describes the packaging models that are fundamental for the design of ultra-high-performance concrete (UHPC), and their evolution. They are divided into two large groups: continuous and discrete models. The latter are those that provide the best answer in obtaining an adequate simulation of the packing of the particles up to nanometric size. This includes the interaction among the particles by means of loosening and wall coefficients, allowing a simulation of the virtual and real compactness of such particles. In addition, a relationship between virtual and real compactness is obtained, through the compaction index, which may simulate the energy of compaction that the particles undergo in their placement in the mold. The use of last-generation additives allows such models to be implemented with water-cement (w/c) ratios close to 0.18. However, the premise of maximum packing as a basic pillar for the production of UHPC should not be the only one. The cement hydration process affected by nanoadditions and the ensuing effectiveness in the properties in both fresh and hardened state according to the respective percentages in the mixture should also be studied. An adequate ratio and proportion of these additions may lead to an obtaining of better results even with lower levels of compactness.

At present, the world is now passing a very far different time than normal situation due to the COVID-19 pandemic crisis. The global life-style and human civilization is currently progressing with down-stream that affecting almost every sectors necessary for human civilizations except the current environmental situation. To control the COVID-19 spreading, most of the countries are following lockdown process that reduces human mobility, thus reducing the CO2 emission to the environment. Though the COVID-19 pandemic is a blessing for the present environment, however, the post-COVID world will face a massive thrust of energy and only conventional energy resources may not be enough to mitigate the energy demands. Solar power generation technology mainly the photovoltaic (PV) systems and their advancement can be the leading possibilities to minimize the gap between the power demand and generation. It is now time to think how we can improve the PV power generation in future and the post-COVID world. In this encyclopaedia communication, we report on Nano-technological approach to improve the conversion efficiency of GaAs solar cells. We have designed and optimized several types of nano-structured assemblies that can be implemented to reduce the front surface incident light reflection losses thus can assist to improve the conversion efficiency of GaAs solar cells.

The science on the anthropogenic airborne aerosols impacting upon the World Heritage marble monument, the Taj Mahal, at Agra has been studied in the light of modern physico-chemical approaches. The study is an effort to understand yet unrecognized airborne species which were found on the surface of the Taj Mahal monument. These species have been analyzed in the light of current analytical methods to impart characterization features and their possible impacts on the surface of the marble. Chemical constituents of these substrates which were incorporated over the top surface of the monument have been identified. Interestingly, the carbon particulates which were thought in the micro level, popularly called “particulate matters” has now been identified even in the nano domain entity, which are chemically more reactive, have been found on the surface of the monument. Because of their high chemical activity these nano carbons do play newer chemistry in the presence of air and sunlight generating several reactive oxygen species (ROS).These ROS are capable to respond to complicated chemical reactions on the surface of the marble in association with deposited cyanophyceae and other deposits of plant origin causing rapid degradation. This study provides the nature of onslaught borne out by such monument exposed under the prevalent smoggy environmental scenario.

The effect of γ-ray irradiation on surface plasmon resonance (SPR) sensing capability of refractive index (n = 1.418–1.448) of the silica glass optical fiber comprised of germano-silicate glass cladding embedded with Au nano-particles (NPs) was investigated. As the γ-ray irradiation increased from 1 hour to 3 hours with the dose rate of 1,190 Gy/h, the morphology of the Au NPs and the SPR spectrum were found to change. The average diameter of Au NPs increased with the aspect ratio from 1 to 2 and the nano-particles became grown to the clusters. The SPR peak wavelength shifted towards longer wavelength with the increase of total dose of γ-ray irradiation regardless of the corresponding refractive indices. The SPR sensitivities (wavelength/refractive index unit, nm/RIU) also increased from 407 nm/RIU to 3,553 nm/RIU, 1,483 nm/RIU, and 2,335 nm/RIU after the γ-ray irradiation at the total dose of 1,190 Gy, 2,380 Gy, and 3,570 Gy, respectively.

Biocompatible polymeric materials with potential to form functional structures in association with different therapeutic molecules have a high potential for biological, medical and pharmaceutical applications. Therefore, the protective capability of the inclusion nano-Complex formed between the sodium salt of poly(maleic acid-alt-octadecene) and a β-lactam drug (ampicillin trihydrate) on the chemical, enzymatic and biological degradation was evaluated. PAM-18Na was produced and characterized as reported previously. The formation of polymeric hydrophobic aggregates in aqueous solution was determined, using pyrene as a fluorescent probe. Furthermore, the formation of polymer-drug nano-complexes was characterized by Differential Scanning Calorimetry-DSC, viscometric, ultrafiltration/centrifugation assays, zeta potential and size measurements by dynamic light scattering-DLS. The PAM-18Na capacity to avoid the chemical degradation was studied through stress stability tests. The enzymatic degradation was evaluated from a pure β-lactamase, while the biological degradation was determined by different β-lactamase producing Staphylococcus aureus strains. When ampicillin was associated with PAM-18Na, the half-life time in acidic conditions increased, whereas both the enzymatic degradation and the minimum inhibitory concentration decreased to a 90 and 75%, respectively. These results suggest a promissory capability of this polymer to protect the β-lactam drugs against chemical, enzymatic and biological degradation.

The sound and heat insulation are among the most important concerns in modern life and nonwoven composite structures are highly effective in noise reduction and heat insulation. In this study, three layered nonwoven composite structures composed of recycled polyester (r-Pet) based thermo bonded nonwoven outer layer and meltblown nonwovens from PP and PBT as inner layers were formed to provide heat and sound insulation. Fiber fineness and cross section of thermo bonded outer layer, fiber type (PP/PBT), areal weight (100/200g/m2) and process conditions (calendared/non-calendared) of meltblown inner layer have changed systematically and the influence of these parameters on thickness, bulk density, air permeability, sound absorption coefficient and thermal resistance of composite structures were analyzed statistically. Also; the results were compared with composite structures including electrospun nano fiber web inner layer and with structures without inner layer. It was determined that sound absorption coefficients ranging between 0.77-0.98 for moderate sound frequencies and 0.99-1 for higher sound frequencies were acquired with developed nonwoven composite structures. Besides, higher sound absorption coefficients were obtained as 0.71 and 0.74 for low sound frequencies such as 800 and 1000Hz, respectively. As a result of this study it can be concluded that developed nonwoven composite structures that provides better sound absorption coefficients and similar thermal conductivity values compared to previous studies and materials in the market can be used as insulation material in required areas.

Optimizing input parameters not only improves production efficiency and processing quality but also plays a crucial role in the development of green manufacturing engineering practices. The aim of the present study is to conduct a comparative evaluation at cutting performance and machinability process during the turning of AISI 4340 steel under different cooling conditions. The study analyses cutting operations during turning using dry, minimum quantity lubrication (MQL), and nano-MQL. As control parameters in the experiments, three different cooling types, cutting speed (100, 150, 200 m/min), and feed rate (0.1, 0.15, 0.20 mm/rev) levels were applied. The experiment results present that the optimal output values are found as Vb=0.15 mm, Ra=0.81µm, 88.1 dB for sound intensity, and I=4.18 A for current. Moreover, variance analysis (ANOVA) was performed to determine the effects of input parameters on response values. Under dry, MQL, and nano-MQL processing conditions, parameters affecting tool wear, surface roughness, current by the motor shaft, and sound level were examined in detail, along with the chip morphology. The responses obtained were optimized according to the Taguchi S/N method. As a result of optimization, it was concluded that the optimum values for cutting conditions (A3B1C1) were nano-MQL cooling and V=100 m/min, f=0.1 mm/rev cutting. Last but not least, it was observed that there was a 13% improvement in tool wear, 7% in current, 9% in surface roughness, and 8% in sound intensity compared to the standard conditions. In conclusion, it was determined that nano-MQL and the lowest level of cutting and feed rate values provided the optimum results.

Generally, mineral fillers are added to thermoplastic polymers to reduce cost and improve performance. However, properly selected mineral fillers can also improve thermal conductivity and deformation behavior, shrinkage, impact strength, dimensional stability, and molding cycle time in thermoset polymers. This study focused on the preparation and microscopic and spectroscopic characterization of various hybrid composites using pumice as primary filler and gypsum, kaolin and hollow glass sphere as secondary fillers, as well as examining some of their mechanical properties and thermal conductivities. For this, first of all, surface modification of the clay was carried out by intercalation method from solution using raw Montmorillonite, cationic surfactant and long chain hydrocarbon material, and then organo-clay melamine formaldehyde nanocomposite was prepared by in situ synthesis using organo clay and melamine formaldehyde pre-polymer. Finally, non-ionic surfactant, foaming agent and glycerin were added to the prepared nano-composite at approximately 90°C, mixed mechanically and then pumice was added. The processes at this stage were repeated while preparing hybrid composites with pumice and other mineral additives. For curing and molding, the composite was first subjected to microwave irradiation for 5 minutes followed by thermal treatment at 140°C for 60 min. Fourier transform infrared spectroscopy (FTIR), X-ray powder diffraction (XRD) spectra and Scanning electron microscope (SEM) and High resolution transmission electron microscope (HRTEM) images were taken for morphological and textural characterization for raw clay (MMT), organo clay (OMMT) and pure polymer with prepared hybrid composites. In addition, some mechanical properties such as bending strength, elasticity modulus and screw holding resistance, as well as thermal conductivity coefficients of the hybrid composites were determined according to the relevant standards and the obtained results were evaluated. Spectroscopic and microscopic analyzes have shown that effective adhesion interactions occur between polymer-clay nanocomposite particles and filler grains, thus resulting in textural arrangements with different properties. Mechanical and thermal conductivity test results showed that melamine formaldehyde-organo-clay nano composite foam and hybrid composite containing hollow glass sphere are highly qualified materials in terms of thermal insulation and mechanical strength.

Extracellular vesicles (EV) such as exosomes, are newly recognized fundamental, natural and physiologic particles of life that seemingly are involved all biologic processes and clinical diseases. Due to their universal involvements, understanding the nature and the potential therapeutic uses of these nano-vesicles requires innovative experimental approaches, in virtually every field. Of the EV group, exosome nano-vesicles and larger companion extracellular micro vesicles (MV) can mediate completely new phenomena dependent on intercellular transfer of proteins and selected RNAs; particularly miRNAs, between donor and targeted cells to elicit epigenetic alterations inducing functional cellular changes. These recipient acceptor cells are nearby (paracrine transfers) or far away after distribution via the circulation (endocrine transfers). The major properties of such vesicles seem to have been conserved over eons, suggesting that they may have ancient evolutionary origins arising perhaps even before cells in the primordial soup from which life evolved. Their potential ancient evolutionary attributes may be responsible for the ability of some modern day exosomes to withstand unusually harsh conditions; perhaps due to unusual membrane lipid compositions. This is exemplified by maternal milk exosome survival of the neonatal acid/enzyme rich stomach. It is postulated that this also applies to their durable presence in phagolysosomes; suggesting unique intracellular release of contents. A major issue discussed is the generally poorly realized superiority of these naturally evolved nano vesicles to therapies compared human engineered artificial nanoparticles; say for treatment of cancers.

A facile and novel synthesis of thirteen 2-amino-3-cyanopyridine derivatives 5(a-m), by a one-pot multicomponent reaction (MCRs), is described for the first time, starting from aromatic aldehydes, malononitrile, methyl ketones, or cyclohexanone and ammonium acetate in the presence of the nanostructured diphosphate Na2CaP2O7 (DIPH) at 80 °C, under solvent-free conditions. These compounds were synthesized in short reaction times with good to excellent yields (84-94%). The diphosphate Na2CaP2O7 is used as an efficient catalyst, environmentally, easy handling, non-toxic, stable, and reusable. Our study was strengthened by the synthesis of five new pyrido[2,3-d]pyrimidine derivatives 6(b, c, g, h, j) by intramolecular cyclization of 2-amino-3-cyanopyridines 5(b, c, g, h, j), with formamide. The synthesized products were characterized by FT-IR, SEM, XRD, TEM, 1H NMR, 13C NMR, TLC, and BET. The operating conditions were optimized using a model reaction in which the catalyst amount, temperature, time, and solvent effect were evaluated. The antibacterial activity was tested against Gram-positive and Gram-negative strains for the synthesized compounds.

In this study, the corrosion performances of ammonium copper quat (ACQ) and boric acid (BA) wood preservatives were investigated, with micronized copper quat (MCQ) and nano boron (NB) used as reference materials. In the study, Scots pine (Pinus sylvestris L.) wood samples were impregnated according to the full-cell process method with ACQ at 2.4% concentration, BA at 4% and MCQ and NB at 1%. The ACQ- and BA-impregnated samples were then impregnated for a second time using five different water-repellent materials: tall oil, linseed oil, sodium silicate, methyl hydrogen silicone and N'-N- (1, 8-Naphthalyl) hydroxylamine. Polyethylene glycol (PEG) 600 and aluminum sulfate were introduced as single impregnations in the form of homogeneous mixtures with the ACQ and BA. The corrosion properties of the impregnated and control samples, including metal weight loss (MWL) and corrosion depth, were examined. As a result, the MWL values of the ACQ-impregnated samples showed an increase compared to the control group. The MWL values of the MCQ-impregnated samples were lower than those of the samples impregnated with ACQ, whilst the MWL values of the BA-impregnated samples were higher than those of the samples impregnated with NB.

The swift progress in low-dimensional nanocarbons, specifically in the realm of the authentic one-dimensional carbon chain featuring sp¹ hybridization, has unveiled exciting prospects for integrating them into cutting-edge technologies across diverse industries. To fully harness their potential, precise control over the growth process is necessary to obtain desired nanostructure and functionality. However, optimizing properties through traditional approaches has been challenging due to complex interactions. To address this, we implement a focused data-driven strategy for nanocarbon inverse design by leveraging a state-of-the-art data-driven nanocarbon genome approach (NCGA). By uncovering relationships between growth parameters and resultant traits, this serves as an expedient catalyst in engineering nanostructures with tailored attributes. We introduce an extensive array of technological approaches aimed at precisely controlling the growth process. These methods encompass stimulating and precisely adjusting synergistic effects, coordinating atomic vibrations at a collective level through the implementation of multilayer nano-interfaces, harnessing the potential of active screen plasma surface engineering, utilizing nano-patterning and allotropic phase transformations, incorporating heteroatom doping, and effectively directing self-assembly. These aim to unlock nanomaterials' latent potential and reveal novel neural pathways within the data-driven NCGA, enhancing its predictive capabilities. Specifically, triggering self-organization during growth can potentially unlock previously unexplored neural pathways. The data-driven NCGA offers a paradigm shift, accelerating discovery and design of nanocarbons with optimized, application-specific properties.

.Various synthetic nematicides are currently used effectively in the control of plant parasitic nematodes. However, these nematicides have adverse effects on humans and the environment. Neem oil is eco-friendly alternatives to synthetic nematicides. The effectiveness of repeated neem oil application in suppressing the root-knot nematodes infestation in figs seedlings was therefore examined in this study, both in its natural form (10 ml/L) and in its nano-emulsion form (5 and 7 ml/L). The recorded reduction parameters of M. incognita were J2/250g soil, galls and egg masses / 5g roots of infected fig seedlings were measured at that time, and the effects of these natural additives were compared with the Fosthiazate (Krenkel 75%EC). The impact of such soil amendments on some typical plant parameters, the total microbial count of soil, and the overall enzymatic activity of the fig rhizosphere were also included. Obtained results revealed that the soil population density of root knot nematode suppressed by 80.3% , reduction of nematode egg masses (60.4%) due to the application of nano-emulsion of neem oil (at 7ml/L). Present work recommend the use of nano-emulsion of neem oil as one of the effective and eco-friendly means to reduce the root- knot nematode on fig .

Numerous structures at the nano- and microscale manifest distinctive properties with far-reaching implications across diverse fields, including electronics, electricity, medicine, and surface engi-neering. Established methods such as nanoimprint lithography, photolithography, and self-assembly play crucial roles in the fabrication of nano- and microstructures; however, they exhibit limitations in generating high-aspect-ratio structures when utilizing high-viscosity pho-tocurable resins. In response to this inherent challenge, we propose a highly cost-effective ap-proach facilitating the direct replication of high-aspect-ratio structures, specifically nanowires, through the utilization of anodized aluminum substrates. This study elucidates the streamlined fabrication process for multiscale porous surfaces achieved through the evaporation-induced in-tegration of solid nanowires printed with high-viscosity photocurable resin.

In this paper, an intelligent blind guide system based on 2D LiDAR and RGB-D camera sensing is proposed, and the system is mounted on the smart cane. The intelligent guide system relies on 2D LiDAR, RGB-D camera, IMU, GPS, Jetson nano B01, STM32 and other hardware. The main advantage of the intelligent guide system proposed by us is that the distance between the smart cane and obstacles can be measured by 2D LiDAR based on Cartographer algorithm, thus achieving Simultaneous localization and mapping (SLAM). At the same time, through the improved yolov5 algorithm, pedestrians, vehicles, pedestrian crosswalks, traffic lights, warning posts, stone piers, tactile paving and other objects in front of the visually impaired can be quickly and effectively identified. Laser SLAM and improved yolov5 obstacle identification tests were carried out inside a teaching building on the campus of Hainan Normal University and on a pedestrian crossing on Longkun South Road in Haikou City, Hainan Province. The results show that the intelligent guide system developed by us can drive the wheels and omnidirectional wheels at the bottom of the smart cane, and give the smart cane a self-leading blind guide function like a "guide dog", which can effectively guide the visually impaired to avoid obstacles and reach the predetermined destination, and can quickly and effectively identify the obstacles on the way out. The laser SLAM speed of this system is 25~31FPS, which can realize the short-distance obstacle avoidance and navigation function both in indoor and outdoor envionments. The improved yolov5 helps to identify 86 types of objects, the recognition rate for pedestrian crosswalks and for vehicles are 84.6% and 71.8%, respectively; the overall recognition rate for 86 types of objects is 61.2%, and the obstacle recognition rate of the intelligent guide system is 25-26FPS.

The human body contains 60-70% of water, depending on age. As a body fluid, it is not only a medium in which physical and chemical processes take place, but it is also one of the active mediators. Water is the richest substance with non-covalent hydrogen bonds. Water molecules, by themselves (in vacuum), are diamagnetic, but when organized into clusters, become diamagnetic or paramagnetic. Also, biomolecules (DNA, collagen, clathrin, and other proteins) have non-covalent hydrogen bonds in their structure. The interaction, as well as signal transmission, between water and biomolecules is achieved through the vibrations of covalent and non-covalent hydrogen bonds, which determine the state and dynamics of conformational changes of biomolecules. Disruptive conformational changes of biomolecules, cells, and tissues lead to their dysfunctionality, so they are a frequent cause of many disorders and diseases. For example, the rearrangement of hydrogen bonding due to mitochondrial disease mutation in cytochrome bc1 disturbs heme bH redox potential and spin state. In order to prevent and repair the dysfunctional conformational changes, a liquid substance was developed based on the second derivative of the C₆₀ molecule (SD-C₆₀), which has classical and quantum properties. Characterization of SD-C₆₀ by UV-VIS-NIR, FTIR, TEM, and AFM/MFM was done and it is shown that SD-C₆₀ water layers generate vibrations with near-zero phase dispersion which are transmitted through the Fibonacci’s water chains to biomolecules. In comparison to previously published SD-C₆₀ derivate (3HFWC, size until 10 nm, and 1-5 water layers), improved formulation (3HFWC-W, size 10-25 nm, and 6-9 water layers) showed multiplied cytotoxic activity against melanoma cell lines of different aggressiveness. Apart from this, the mode of action was preserved and based on induction of senescence rather than cell death. Importantly, high selectivity toward malignant phenotype was detected. Observed effects can be ascribed to a machinery of hydrogen bonds, which are generated in SD-C₆₀ and transmitted through water to biomolecules. This approach may open a new field in science and healthcare - a “water-based nanomedicine”.

Poor interlaminar fracture toughness has been a major issue in glass fiber-reinforced epoxy resin (GF/EP) laminate composites. In this paper, soft carboxy-terminated liquid nitrile (CTBN) rubber particles and rigid nano-SiO2 are used to toughen the epoxy resin (EP) matrix to improve the interlayer properties of GF/EP laminate composites. The effects of adding two toughening agents on the mechanical and interlayer properties of GF/EP laminates were studied. The results showed that adding the two kinds of particles improved the mechanical properties of the epoxy matrix. When the additional amount of flexible CTBN rubber particles was 8wt%, and the rigid nano SiO2 was 0.5wt%, the fracture toughness of the matrix resin was increased by 215.8%, and the tensile strength was only decreased by 2.3% compared with the pure epoxy resin. On this basis, the effects of two kinds of particles on the interlayer properties of GF/EP composites were studied. Compared with the unmodified GF/EP laminates, the interlayer shear strength and mode Ⅰ interlayer fracture toughness is significantly improved by toughening agent, and the energy release rate GIC of interlayer shear strength and interlayer fracture toughness is increased by 109.2%, and 86.8%, respectively.

The rapid advancements in gene therapy have opened up new possibilities for the treatment of genetic disorders, including Duchenne muscular dystrophy, Thalassemia, cystic fibrosis, Hemophilia, and Familial hypercholesterolemia. The utilization of the clustered regularly interspaced short palindromic repeats (CRISPR) - CRISPR-associated protein (Cas) system has revolutionized the field of gene therapy by enabling precise targeting of genes. In recent years, CRISPR/Cas9 has demonstrated remarkable efficacy in treating cancer and genetic diseases. However, the susceptibility of nucleic acid drugs to degradation by nucleic acid endonucleases, necessitates the development of functional vectors capable of protecting the nucleic acids from enzymatic degradation, while ensuring safety and effectiveness. This review aims to explore the biomedical potential of non-viral vector-explore CRISPR/Cas9 systems for the treatment of genetic diseases. Furthermore, it provides a comprehensive overview of recent research advances in viral and non-viral vector-based gene therapy for genetic disorders, including insights from preclinical and clinical studies. Additionally, the review analyzes the current limitations of these delivery systems and proposes avenues for the development of novel nano-delivery platforms.

This paper presents results of the magnetic dynamics study (the microwave power absorptions at the fixed frequencies, during magnetic field sweeping) in samples of Y3Fe5O12 single crystals in the form of plates and spheres of various sizes, at frequencies exceeding 30 GHz, in magnetic fields up to 18 kOe, at room temperature and T=77 K. It was found, that in this case, the inhomogeneity’s of the magnetic state manifested itself in the Y3Fe5O12 samples in as 2D local phase separation regions. These 2D phase separation regions formed inside domain walls representing superlattices with size’s 700 – 900 Å. Landau diamagnetism or de Haas van Alphen oscillations observed in the 2D phase separation regions at room temperature and T=77 K, depending on the shape and size of the studied plates and spheres.

In its 8th Malaysia Plan (MP*), the Malaysian government has given nanotechnology development a high priority and has been made a Strategic Research (SR) programme. Consequently, an exhaustive and long-term approach is essential. Additionally, specific laws are required to provide an optimal health and safety environment for workers. Consequently, the current study intends to assist Malaysian policymakers in promoting improved safety, risk assessment, and management for nanotechnology workplaces, as well as drafting a comprehensive policy for the recently released DOSH guideline in 2018. Utilizing a unique methodology, this study evaluated the assessment and management of nanotechnology health and safety risks in Malaysia using the international risk governance council (IRGC) framework. In addition to document analysis, n = 20 semi-structured interviews were conducted with representatives of several nanotechnology platforms to collect data that was then analyzed thematically. The research evaluated current workplace safety regulations and laws. Consequently, we propose a future dynamic strategy for Malaysian nanotechnology with more favourable upgrades supported by increased concentrations in the following areas: I policy creation, ii) comprehensive management system, iii) knowledge transfer, and iv) infrastructure management. In addition, the findings highlight the need of cross-sectional communication in bridging existing gaps. This study laid the groundwork for a more systematic and comprehensive health and safety strategy.

A comparative analysis of the features of UV- stimulated emission (SE) of various types of disorder active materials based on ZnO crystallites for a random laser (RL) was carried out. The superlinear increase in the intensity of the UV photoluminescence (PL) band of polydisperse nano- microcrystalline (PNMC) ZnO powder at a wavelength of λ = 387 nm and some narrowing of its half-width in the range of 20-15 nm with increasing pump intensity indicate random lasing with incoherent feedback (FB). Properties of similar UV PL bands under the same conditions from a thin film containing hexagonal ZnO microdisks, as well as samples of monodisperse ZnO nanopowder indicate stimulated emission with coherent feedback. It is shown that, among the studied materials, the PNMC ZnO powder with crystallites contained nano-grains with is the most suitable for creating a laser with incoherent feedback at room temperature. The dominant factor of UV SE in PNMC ZnO powder is radiation transitions under exciton - exciton scattering conditions. The possible mechanisms of this random emission with the continuous spectrum are discussed. The average optical gain coefficient αg at λ = 387 nm in this RL system is estimated, as αg ~ 150 cm-1.

Biochar is a carbon allotrope obtained by pyrolysis of biomass, usually agro-waste. Owing to the demand for sustainable development, biochar is continuously raising much hope in the scientific community. However, in order to impart it with new properties, its modification is required, either in situ during pyrolysis, or after the carbonization process. Herein, we propose a new direct approach to obtain bimetallic copper/nickel nanoparticle-loaded on olive stone biochar. The bimetallic-coated biochar and the reference materials bare biochar, copper-loaded and nickel-loaded biochar were prepared at 400 °C under a stream of dinitrogen from olive pit powder particles impregnated first with citric acid (CA), and then with copper and nickel nitrates. We have employed citric acid in the process in order to check its effect on the structural and textural properties of biochar supporting the metallic nanoparticles. Surprisingly, citric acid induced the formation of agglomerated or even raspberry-shaped, bimetallic copper/nickel nanoparticles. Large 450-500 nm-sized agglomerates of ~80 nm bimetallic CuNi NPs were noted for B-CA@CuNi. Interestingly, for biochar material prepared with initial Cu/Ni=10 molar ratio (B-CA@CuNi10/1), the bimetallic NPs formed unusual nano-raspberries (1748 nm in size) which are agglomerates of individual 10-20 nm-sized CuNi10/1 nanoparticles. The B-CA@CuNi and reference materials were characterized by Raman spectroscopy, scanning electron microscopy (SEM)/energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) and magnetometry. The B-CA@CuNi and B-CA@Ni materials could be attracted efficiently with a magnet, but not B-CA@CuNi10/1 due to a low nickel loading. B-CA@CuNi was tested as a catalyst for the degradation of methyl orange (MO). Discoloration was noted within 10 min, much faster than a similar material prepared in the absence of CA. B-CA@CuNi could be recycled at least 3 times with exhibit as fast discoloration catalysis performance. This paper stresses the important role of citric acid in shaping the bimetallic nanoparticles loaded in situ on biochar during the slow pyrolysis process and to enable faster catalysed discoloration of organic dye solution.

The process of water treatment by nanoparticles is one of the most considerable subjects in the cross-field of hydrodynamics, chemistry and mathematics. This paper is dedicated to the case of the flows that appear when squeezing and stretching a spongy with a mix of water with nanoparticles and contaminants. It is assumed that fluid is homogeneous at the starting moment, the parameters of the nanoparticles and contaminants are known, and there is a constant non-homogeneous magnetic field applied to the system. The flow starts moving when the walls of the channel shift to each other. Exact and numerical solutions of the system of ordinary differential equations are used to receive the results. The article gives an answer to the question about stability of the flow and proposes the technique to evaluate the essential characteristics of the system to achieve the treatment process efficiency. The main result is that the considered system shows excellent treatment properties during some part of squeezing stage. This effect does not appear without magnetic field.

Lamellar eutectic structure of Al_0.7CoCrFeNi high-entropy alloy (HEA) is emerging as a promising candidate for structural applications because of its high strength-ductility combination. The alloy consists of a fine-scale lamellar fcc+B2 microstructure with high flow stresses >1500 MPa under quasi-static conditions. The response to shear loading was not investigated so far. This is the first report on the shear deformation of an eutectic structured HEA and effect of precipitation on shear deformation. The dynamic shear response (DSR) of the eutectic HEA was examined in two microstructural conditions, with and without the presence of L1₂ precipitates. A split-Hopkinson pressure bar (SHPB) was used to compress the hat-shaped specimens to study the local DSR of the alloy. The adiabatic shear bands (ASBs) in two different microstructural conditions were characterized after deformation at dynamic strain rates. The adiabatic shear localization occurs at low strains for the high strength material, and the eutectic microstructure does not delay cracking. The width of ASBs and the extent of plastic deformation around them has been correlated with the rate of straining. Dynamic recrystallization within ASBs and profuse twinning around it was observed. Local mechanical response of individual lamellae before and after shear deformation was examined using nano-indentation.

This paper introduces an innovative nanotechnology-based approach that provides a pathway to enhance the energy release efficiency of nanoenergetic materials (nEMs) by harnessing self-synchronized collective atomic vibrations and phonon wave resonance within the transition domains between nanocomponents, without altering the material composition. The key innovation involves incorporating finely-tuned 2D-ordered linear-chain carbon-based multilayer nano-enhanced interfaces as programmable nanodevices into the transition domains using advanced multistage processing and assembly techniques. These programmable nanodevices enable precise control over self-synchronized collective atomic vibrations and phonon wave propagation, leading to synergistic effects. To activate and optimize these effects, a combination of various methods is employed, including energy-driven initiation of allotropic phase transformations, surface acoustic wave-assisted micro/nano-manipulation, heteroatom doping, directed self-assembly using high-frequency electromagnetic fields, and data-driven inverse design approaches. By leveraging a data-driven inverse design strategy and uncovering hidden structure-property relationships, we maximize energy release efficiency using the carbon nano-materials genome approach derived from multifactorial neural network-based predictive models. This approach not only unlocks new functionalities in nEMs but also improves environmental performance and safety levels. By pioneering transformative pathways for nEMs through harnessing phonon wave resonance in low-dimensional nanocarbon transition interfaces, this research brings significant advancements in the field.

The capacity and the mechanism of the adsorption of aqueous barium (Ba), cobalt (Co), strontium (Sr) and zinc (Zn) by Ecuadorian (NatAllo) and synthetic (SynAllo-1 and SynAllo-2) allophanes were studied as a function of contact time, pH and metal ion concentration using kinetic and equilibrium experiments. The mineralogy, nano-structure and chemical composition of the allophanes were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy and specific surface area analyses. The evolution of adsorption fitted to a pseudo-first-order reaction kinetics, where equilibrium between aqueous metal ions and allophane was reached within < 10 min. The metal ion removal efficiencies varied from 0.7 to 99.7 % at pH 4.0 to 8.5. At equilibrium, the adsorption behavior is better described by the Langmuir model than by the Dubinin-Radushkevich model, yielding sorption capacities of 10.6, 17.2 and 38.6 mg/g for Ba^(2+), 12.4, 19.3 and 29.0 mg/g for HCoO_2^-, 7.2, 15.9 and 34.4 mg/g for Sr^(2+) and 20.9, 26.9 and 36.9 mg/g for Zn^(2+), respectively, by NatAllo, SynAllo-2 and SynAllo-1. The uptake mechanism is based on a physical adsorption process. Allophane holds great potential to remove aqueous metal ions and could be used instead of zeolites, montmorillonite, carbonates and phosphates for wastewater treatment.

This work is concerned with studying the change of some Optical and Electrical Properties of Ba_xFe_(1-x)TiO₄ thin films due to the change of the nano crystal size. Simple theoretical explanation based on the string theory was developed. The empirical results obtained indicated that the absorption coefficient, electrical conductivity, and the magnetic permeability increase upon decreasing the nano crystal size. However, the transmission coefficient, and the refractive index increase upon increasing the nano crystal size. All these changes are explained using a simple string model with the aid of Newton's laws. The capability of the string theory to explain this nano quantum behavior comes from the fact that the string theory recognize both the particle and the wave nature of the nano system. This is similar of course to the quantum approach which is based mainly on the dual wave particle nature of atomic systems and entities.

Control of autonomous robot motion in radial mass density field is presented. In that sense the robot motion is described as the function of the radial mass density parameters. The radial mass density field is between the maximal radial mass density and the minimal radial mass density. Between these two limited values one can use n points (n = 1, 2, . . . nmax) and calculate the related radial mass density for each point. The radial mass density is maximal at the minimal gravitational radius and minimal at the maximal gravitational radius. This conclusion is valid for Planck scale, but also for the scales that are less or higher of that one. Using the ratio of the Planck mass and Planck radius it is generated energy conservation constant with value κ = 0.99993392118. Further, in this theory it is possible to connect Planck’s and gravitational parameters as functions of the maximal (or minimal) radial mass density. In that sense the autonomous robot motion in radial mass density field is important for the control of the robot motion at micro and nano scales.

Biosensors are measurement devices that can sense several biomolecules, and are widely used for the detection of relevant clinical pathogens such as bacteria and viruses, showing outstanding results. Because of the latent existing risk of facing another pandemic like the one we are living due to COVID-19, researchers are constantly looking forward to developing new technologies for diagnosis and treatment of infections caused by different bacteria and viruses. Regarding that, nanotechnology has improved biosensors design and performance through the development of materials and nanoparticles that enhance their affinity, selectivity, and efficacy in detecting these pathogens, such as employing nanoparticles, graphene quantum dots, and electrospun nanofibers. Therefore, this work aims to present a comprehensive review that exposes how biosensors work in terms of bacterial and viral detection, and the nanotechnological features that are contributing to achieving a faster yet still efficient COVID-19 diagnosis at the point-of-care.

Direct laser writing three-dimensional nano-lithography is an established technique for manufacturing functional 3D micro- and nano-objects via non-linear absorption induced polymerization process. In this Chapter an underlying physical mechanisms taking place during nano-confined polymerization reaction, induced by tightly focused ultra-short laser pulses, are reviewed and discussed. The special attention is paid on the effects that directly impact structuring resolution and minimum achievable feature size. Analysis of possible photo-initiation mechanisms as contributing multi-photon absorption and avalanche ionization in pre-polymers under diverse exposure conditions (wavelength, pulse duration) is presented. Feasible structuring of pure (non-photosensitized) and functional nanoparticles doped polymer precursors is justified and benefits of such materials/structures for microoptics, photonics and cell scaffolds are highlighted. The influence of temperature effects (induced by writing process itself or determined by ambient conditions) on polymerization process, observed in different pre-polymers under diverse exposure regimes is outlined. The further adjustment of the structuring resolution is possible via precise control of light polarization and diffusion assisted radical quenching. The work is concluded with a brief outlook on future challenges and perspectives related to refinement of 3D ultra-fast laser lithography fabrication process in the means of application of diverse post-processing methods and research into novel photo-curable materials including inorganic ones.

Given the rise in the number of cases and their recurrences, Urinary Tract Infections (UTI) are one of the major burdens on public healthcare worldwide. Rapid, inexpensive and selective detection of Uropathogenic E. coli (UPEC), a major contributor to UTIs, is the need of the hour for effective treatment, given the rise of antibiotic-resistant bacteria due to improper diagnosis. Here we present a rapid, real-time, selective and label-free detection of UPEC using an integrated sensing platform based on Crossed Surface Relief Gratings (CSRGs) as nanoplasmonic sensors. Detection is achieved due to the unique Surface Plasmon Resonance (SPR)-based light energy exchange attributed to the CSRGs, allowing real-time sensing in a very narrow bandwidth of the incident light to pass where the SPR energy conversion occurs. The sensing ability of the platform is experimentally demonstrated by the detection of bulk Refractive Index (RI) changes, with a bulk sensitivity of 382.2 nm/RIU and a resolution in the order of 10-6 RIU. We demonstrate selective capture and detection of clinical concentration of UPEC, as opposed to other gram-negative bacteria, in real-time, a first for CSRGs. This work is particularly important for effective treatment of UTIs, allowing point-of-care diagnosis for economically disadvantaged regions around the world.

A new generation of nano-technologies is expanding solid propulsion capabilities and increasing their relevance for versatile and manoeuvrable micro-satellites with safe high-performance propulsion. We propose the innovative concept, connected with application of new synergistic effect of the energetic materials performance enhancement and reaction zones programming for the next generation small satellite multimode solid propulsion system. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon, by the properties of the energetic materials reaction zones and by localization of the energy release areas. This synergistic effect can be provided through application of the functionalized carbon-based nanostructured metamaterials as a nano-additives along with simultaneous manipulating by their properties through the electrostatic field. Mentioned effect will be controlled through predictive programming both by the spatial structure and physics-chemical properties of the functionalized carbon-based nano-additives and through the electromagnetic control of the self-organized wave pattern excitation and micro- and nano- scale oscillatory networks in the energetic material reaction zones. Suggested new concept makes it possible to increase the energetic material regression rate and increase the thrust of the solid propulsion system with minimal additional energy consumption.

Two pilot scale desalination system employing carbon modified nano-sized, zero valent metals (n-ZVM) were maufactured and tested to determine (1) the degree to which high salt water (20 to 130 mS) could be desalinated and (2) if this degree of desalination could be maintained throughout an extended treatment period. Two pilot systems were tested (referred to as Generation 1 and Generation 2) consisting of parallel lines of 4 individual reactors in series, a settling tank and an activated carbon cell at the end of each reactor line. The system capacity was 300 gal in Generation 1 and 600 gal in Generation 2 total with a total hydraulic residence time of 6 hours per reactor line (one hour per cell/tank). A slurry of n-ZVM was introduced in the first reactor on each line to yield approximately 5 to 45 grams of nano-metal per 100 L of influent salt water. The n-ZVM slurry was made from mixing tea extract with metal salts (eg ferrous sulfate, ferric chloride) to produce the carbon modified metal slurry. Initial runs focused on dosing required to achieve maximum salt removal at each of three influent salt contents, 28 mS, 44 mS and 123 mS. Once dosing was set, continuous runs (14 days, 23 days and 9 days) were carried out to (1) examine the ability of the pilot to maintain the removal efficiency over an extended period, (2) to determine the weaknesses inherent in the pilot systems, and (3) to begin to develop CAPEX and OPEX estimates for the pilot and pre-design full scale mobile desalination unit (MDU) system. Results demonstrated that maximum removal occurred with 10 g/100L of salt for the 30 mS salt solution,16 g/100 L of salt for the 40 mS influent water and 40 g/100 L for the 130 mS influent. Salt removal (expressed as Na and Cl removed) approached 78% for the 30 mS influent and 41 mS influent respectively while removal for the highest salt influent (130 mS) approached 81 %. Addition of greater amounts of carbon modified slurry than those described resulted in a pH less than 6 which inhibits continued salt removal and would require addition of calcium or magnesium oxides/hydroxides or bicarbonate solutions at the influent side to achieve greater salt removal and of course greater cost per gallon. Continuous operation over the extended time-period showed no significant decrease in salt removal with typical day to day variation of no more than 10% suggesting that this approach to desalination could rapidly provide usable water from saline aquifers, seawater or even produced water. Treatment of saline waters at 30 mS or less yields effluent water in the range necessary for irrigation use of many crops while treatment of seawater or produced water levels of salt (40 mS or higher) yields effluent in the range of 8 to 10 mS a range ideal for RO influent that would prevent the production of large volumes of brine. Pilot testing continues with seawater extracted from Puget Sound, Seattle WA and higher levels of salt to better represent produced water.

This study explored the potential synergism within chlorhexidine-silver nanoparticles conjugates against Influenza type A, Staphylococcus aureus, Escherichia coli, and Candida albicans. Silver nanoparticles (SN) were obtained by the reduction of silver ions with green tea total phenolic extract and conjugated with chlorhexidine (Cx). The particles were characterized by UV-Vis and FTIR spectroscopies, dynamic light scattering, X-ray diffraction, and transmission electron microscopy. A stable negatively-charged nano-silver colloid (ζ=-50.01) was obtained with an average hydrodynamic diameter of 92.34 nm. In the presence of chlorhexidine, the spectral data and the shift of the zeta potential to positive values (ζ=+44.59) revealed the successful sorption of the drug onto the silver surface. The conjugates (SN-Cx) demonstrated potentiation in the effects against S. aureus and C. albicans, and synergism against E. coli with minimal inhibitory concentrations of SN 5.5 µg/mL+Cx 8.8 µg/mL. The SN showed excellent, increasing with time, virucidal properties, and low toxicity. The coupling of the cationic chlorhexidine with nano-silver, however, did not reduce its intrinsic cytotoxicity on various cell lines (MDCK, BJ, and А549). The newly-synthesized antimicrobial agent presented with an extended and promising therapeutic spectrum and needs to be further evaluated on relevant to the designated route of administration three-dimensional cell models (e.g., nasal, bronchial, dermal, ocular, etc.).

Accumulation of proteins in filter membranes limits the efficiently of filtering technologies for cleaning wastewater. Efforts are ongoing to coat commercial filters with different materials (such as titanium-dioxide, TiO2) in order to reduce the fouling of the membrane. Beyond monitoring the desired effect of retention of biomolecules, it is demanding to understand what are the biophysical changes in water-soluble proteins caused by interacting with the new coated filter membranes, an aspect that has received little attention so far. Using spin label electron paramagnetic resonance (EPR), aided with native fluorescent spectroscopy and dynamic light scattering (DLS), here we report the changes in the structure and dynamics of bovine serum albumin (BSA) exposed to TiO2 (P25) nanoparticles or passing through commercial polyvinylidene fluoride (PVDF) membranes coated with the same nanoparticles. We have found that the filtering process and prolongued exposure to TiO2 nanoparticles had significant effects on different regions of BSA, and denaturation of the protein was not observed, neither with TiO2 nanoparticles nor by pressing through TiO2-coated filter membranes.

In this paper, various Ni-P composite coatings containing toner, MoS2, and nano-SiO2 particles were deposited on steel substrates by the electroless method. Then, the electrochemical properties of these coatings after a heat treatment process were compared. The microstructural evaluations were also done by using the optical and electron microscopy methods. Both Tafel polarization and electrochemical impedance spectroscopy techniques were utilized to survey the electrochemical behavior of such coatings. The surface morphology of all coatings contained cauliflower-like nodules. The X-ray diffraction patterns showed the crystalline phases of Ni and Ni3P for all coatings after the heat-treatment step. Obtained results showed that all composite coatings exhibited lower corrosion rates with respect to Ni-P coatings. Such a reduction was about 21.6-92.2%. This behavior was attributed to the presence of reinforcement as barriers for corrosive ion diffusion through the coating plus the changes in detected phases and thickness. Electrochemical impedance spectroscopy test results also demonstrated that the increase in the polarization resistance for composites coatings was about 18.4-85.3% after 1 h immersion in a 0.6M NaCl solution; however, when the immersion time increased to 24 h, such increased resistance changed to 18.1 to 73.1%. Totally, despite the lower deposition rate, the presence of MoS2 and nano-SiO2 particles were more effective than toner particles to raise the corrosion rate of the Ni-P coating.

Hand gestures may play an important role in medical applications for health care of elderly people, where providing a natural interaction for different requests can be executed by making specific gestures. In this study we explored three different scenarios using a Microsoft Kinect V2 depth sensor then evaluated the effectiveness of the outcomes. The first scenario utilized the default system embedded in the Kinect V2 sensor, which depth metadata gives 11 parameters related to the tracked body with five gestures for each hand. The second scenario used joint tracking provided by Kinect depth metadata and depth threshold together to enhance hand segmentation and efficiently recognize the number of fingers extended. The third scenario used a simple convolutional neural network with joint tracking by depth metadata to recognize five categories of gestures. In this study, deaf-mute elderly people execute five different hand gestures to indicate a specific request, such as needing water, meal, toilet, help and medicine. Then, the requests were sent to the care provider’s smartphone because elderly people could not execute any activity independently. The system transferred these requests as a message through the global system for mobile communication (GSM) using a microcontroller.

DNA origami has emerged in recent years as a powerful technique for designing and building 2D and 3D nanostructures. While the breadth of structures that have been produced is impressive, one of the remaining challenges, especially for DNA origami structures intended to carry out useful biomedical tasks in vivo, is to endow them with the ability to detect and respond to molecules of interest. Target molecules may be disease indicators or cell surface receptors, and the responses may include conformational changes leading to release of therapeutically relevant cargo. Nucleic acid aptamers are ideally suited to this task and are beginning to be used in DNA origami designs. In this review we consider examples of uses of DNA aptamers in DNA origami structures and summarise what is currently understood regarding aptamer-origami integration. We review three major roles for aptamers in such applications: protein immobilisation, triggering of structural transformation, and cell targeting. Finally, we consider future perspectives for DNA aptamer integration with DNA origami.

Targeted Protein Silencing (TPS) is an elegant approach to investigate protein function and its role in the cellular landscape, overcoming limitations of genetic perturbation strategies. In contrast to CRISPR/Cas9 and RNA interference, these systems act in a reversible manner and reduce off-target effects. Several TPS have been developed and wisely improved, including compartment delocalization tools and protein degradation systems. In this review, we focus on Anchor-Away, deGradFP, auxin inducible degron (AID) and dTAG technologies, and discuss their recent applications and advances. Finally, we propose Nano-Grad, a novel nanobody-based protein degradation tool to specifically proteolyze endogenous tag-free target protein.

Nano-drugs and nano-delivery systems are rapidly evolving, with new strategies emerging in the current practices. The evolution of these technologies began with modifying the chemical structure, progressing to supramolecular ionic complexes, and culminating in elegant ad hoc delivery systems. Nanoparticles have numerous benefits as a carrier system for delivering therapeutic agents to intra-arterial sites. These benefits include their subcellular size, targeted surfaces, good suspensibility, and uniform dispersity, making them an ideal choice for catheter-based delivery. Despite the advancements made in the field of nano-drugs and nano-delivery systems, there are still some hurdles to overcome in terms of their commercial availability.The current review presents an updated summary of recent advancements in nano-drugs and nano-delivery systems, including their commercial availability. We aim to discuss the present challenges and prospects of commercially available nano-drugs and nano-delivery systems. Here, we provide a precise and informative overview of the current state of these technologies and underscore the potential they hold for future developments. Further, we have categorized commercially available modifications, name, parent company and their main applications in nano-drugs.

Lately Silicon Carbide (SiC) and Galium Nitride (GaN) based high frequency power conversion has gained immense popularity which stems from relatively low switching energy, robustness to high temperature operation, wide-band gap and superior thermal limits. While this aspect inherently results in a high-density power stage design, the design of adjoining passive components, particularly magnetics, needs careful attention. This is especially true if the compatibility of core and winding options and their performance is limited with the use of higher switching frequency. In this regard, this paper presents a brief review of existent research conducted in materials, optimization and integration of magnetics for single and three phase applications, ranging from filters, resonant inductors to isolation transformers. Design knobs pertaining to medium voltage (MV) applications, low-voltage (LV) applications, e-mobility sector such as more electric aircrafts (MEAs) and electric vehicles (EVs) are discussed. Guidelines for magnetics design are summarized for each application with a projected roadmap on future trend for magnetics.

Research on the chemical mechanism and reciprocal behavior of the coronavirus relate to living organisms, engaging in the give and take of electrochemical mediators, is a very important, controversial and vital issue. What we should accept is the chemical identity of this scenario, and not preferably a characteristic of a biological system. This chemical reaction should be familiar, referring to the theory of chemical pathways involved in DNA/proteins in the body against aggressive guests (such as viruses). From the point of view of a chemist, this simple reaction is nothing more than an oxidation-reduction reaction (redox-stress signaling) which conducted and carried out by coronavirus in a biointerface medium. Thereby, oxidizing as well as reducing reagents should be very constructive, promoting development in such chemical process. We understand redox reactions as switchable thiol/disulfide exchanges (formation and cleavage of inherent disulfide bonds), then, we can hugely profit from redox-responsive nano-surfaces equipped with multiple new ionic and covalent interactions. This game-changing idea can substantiate by surface modified-nanoparticles to play powerful roles in synthesis of nano oxidizers as well as reducing agents in nanomedicine. Chemists and pharmacists must then explore new thoughts and present modern experiences/approaches of preparation nanoparticles and nanocomposites to create novel vaccines as well as coronavirus drugs. In this regard, this experience can also be so helpful for HIV/AIDS, which is caused by viruses.

Poly(hydroxyalkanoates) (PHAs) are currently considered competent candidates to replace traditional plastics in several market sectors. However, commercial PHA grades exhibit unsatisfactory smell that can negatively affect the quality of the final product. The cause of this typical rancid odour is attributed to oxidized cell membrane glycolipids, coming from Gram negative production strains, which remain frequently attached to PHAs granules after extraction. The aim of this research is the development of customised PHA nano-biocomposites for industrial applications containing organo-modified nanoclays with high adsorption properties able to capture volatile compounds responsible of the displeasing fragrance in PHAs. To this end, a methodology for the detection and identification of the key volatiles released due to oxidative degradation of PHAs has been established using a headspace solid-phase microextraction technique. We report the development of nine nano-biocomposite materials based on three types of commercial PHA matrices loaded with three species of nanoclays which represent a different polar behaviour. It has been demonstrated that although the reached outcome effect depends on the volatile nature, natural sepiolite (T2) might result in the most versatile candidate for all PHA matrices selected.

Over recent years, nanocarriers have played an ever-increasing role in clinical and biomedical applications owing to their unique physicochemical properties and surface functionalities. Lately, much effort has been directed towards the development of smart, stimuli-responsive nanocarriers that are capable of releasing their cargos in response to specific stimulus. These intelligent-responsive nanocarriers can be further surface-functionalized so as to achieve active tumor targeting in a sequential manner, which can be simply modulated by the stimuli. By applying this methodological approach, these intelligent-responsive nanocarriers can be directed to different target-specific organs, tissues or cells, and exhibit on-demand controlled drug release that may enhance therapeutic effectiveness and reduce systemic toxicity. Light, an external stimulus, is one of the most promising triggers for use in nanomedicine to stimulate on-demand drug release from nanocarriers. Light-triggered drug release can be achieved by light irradiation at different wavelengths, either in UV, visible or even NIR region, depending on the photophysical properties of the photo-responsive molecule embedded in the nanocarrier system, the structural characteristics and material composition of the nanocarrier system. In this review, we highlighted the emerging functional role of light in nanocarriers, with emphasis on light-responsive liposomes and dual-targeted stimuli-responsive liposomes. Moreover, we provided the up-to-date phototriggered targeting strategies and mechanisms of light-triggered drug release from liposomes and NIR-responsive nanocarriers. Lastly, we addressed the current challenges, advances, and future perspectives for the deployment of light-responsive liposomes in targeted drug delivery and therapy.

Compressive residual stresses in thin films can inhibit crack propagation under normal or sliding contact loading, with associated enhancement of the coating apparent toughness, load bearing capacity and wear resistance. This study investigates the influence of residual stress distributions on the thin film/substrate adhesion using a nanoindenter coupled with scanning electron microscope (SEM) investigations of indentation induced failure modes. Reactive and un-reactive magnetron sputtering with ion plating was used to coat a (100) silicon substrate with aluminum nitride (AlN) with and without an aluminum (Al) adhesion layer. The presence of an Al bond layer gives additional interfacial tensile stress because of the difference in thermal expansion coefficient. Additionally, a different magnitude of residual stresses in the AlN coating was achieved by changing the applied bias voltage onto the substrate. Wafer curvature method and incremental focused ion beam (FIB) milling, combined with high-resolution in situ scanning electron microscopy (SEM) imaging and full field strain analysis by digital image correlation (DIC), were used to measure the average and in-depth stress residual stress distribution in the produced coatings. The adhesion energy was then quantified by using a nanoindentation based model. Results demonstrate that the additional tensile residual stress in the aluminum adhesion layer decrease significantly the coating adhesion, even in presence of a higher compressive stress state in the AlN top-layer. Therefore, the coatings without Al-layer showed better adhesion because of a more homogeneous compressive residual stress in comparison with the coating having Al layer, even though both groups of coatings are produced under same bias voltage. Results are discussed, and some general suggestions are made on the correlation between coating/substrate property combination and the adhesion energy of multilayer stacks. The results suggested that Al bond-layer and inhomogeneous residual stresses affected the adhesion of AlN negatively to a substrate like silicon.

Distracted driving is the leading cause of accidents, the cause of these distractions may include drowsiness, using cell phone, smoking a cigarette, etc. The proposed paper aims at monitoring the attentiveness of the driver and alerting the driver when his/her alertness goes below a certain threshold. It uses image processing using OpenCV (Computer Vision) and You Look Only Once (YOLO) algorithm to detect the eyes and object respectively and sounds an alarm when the driver is either drowsy or using his cell phone or smoking a cigarette.

Despite recent improvements in the methods used to eradicate and minimize mosquito populations, they still pose severe threats to human health. This study aimed to investigate the Larvicidal potentials of silver nanoparticles of Ocimum gratissimum on wild Anopheles larvae from Lagos. The plant used in this study was collected from the southeastern part of Nigeria, Ibite-Olo in Ezeagu Local Government Area of Enugu State. Wild Anopheles mosquito larvae were collected from a field at Kosofe Local Government Area of Lagos State, Nigeria where resistant Anopheline populations have been reported in and around Lagos State were brought to the laboratory and kept under standard insectary conditions (25–29 °C;78–82% relative humidity). Aqueous extract of Ocimum gratissimum was made and subsequently into the silver nanoparticles. A bioassay test was performed according to WHO guidelines, with six different concentrations to assess the larvicidal activity and values obtained were subjected to log prohibit regression analysis to obtain LC₅₀ and values with 95% confidence limit. The results of the larvicidal activities of the silver nanoparticles of Ocimum gratissimum showed that the mortality rate was dose-dependent with the percentage mortality increasing at a direct proportional rate as with dose and time of exposure. Ocimum gratissimum gave LC₅₀ at 0.5 ppm and LC₉₅ at 2.5 ppm respectively. The biosynthesized silver nanoparticles augmented the larvicidal activity of the silver nanoparticles of Ocimum gratissimum on wild Anopheles larvae from Lagos. Therefore, this study showed that the silver nanoparticles of Ocimum gratissimum have the potency to be used against an insecticide-resistant mosquito vector and are a suitable candidate for the development of novel natural insecticides.

Nano-scale organofunctional silanes have been developed, tested and successfully applied to protect stone buildings in Europe against climatic effects since the 1860s. The same nanotechnologies can also be used in pavement engineering to create strong chemical bonds between a stabilising agent and the material substrata. The attachment of the organofunctional silane to a material also makes the surface of the material hydrophobic, reducing future chemical weathering. These properties allow naturally available materials to be used in any pavement layer at a low risk. In the built environment, scientists soon determined that the successful use of an organo-silane depends on the type and condition of the stone to be treated. The same principles apply to the implementation of applicable nanotechnologies in pavement engineering. Understanding the basic chemistry determining the properties of the stabilising agent and the organofunctional modifying agent and the chemical interaction with the primary and secondary minerals of the material are essential for the successful application of these technologies in pavement engineering. This paper explains some basic chemistry which fundamentally influences engineering outputs that can be achieved using New-age (Nano) Modified Emulsions (NME) stabilising agents with naturally available material in all road pavement TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back

Recent advances in nanomaterials have been heavily influenced by low-dimensional nanocarbon allotropes. In particular, carbyne has attracted attention for its potential as a true one-dimensional carbon chain with sp1 hybridization. To maximize the capabilities of this material, we employ a focused data-driven inverse design approach based on the carbon nanomaterials genome concept. This involves using deep learning neural network models to identify key descriptors tied to desired properties, enabling property prediction and reverse engineering of nanocarbons. Our iterative approach entails: (i) gathering growth/property data on nanostructures; (ii) identifying informative numerical/categorical predictors; (iii) developing deep learning models mapping descriptors to properties; (iv) refining models with new insights; (v) determining required descriptors/conditions for target properties via inverse mapping; (vi) validating models by synthesizing predicted nanostructures; and (vii) enhancing models with validation data. This allows uncovering hidden growth-property connections, precisely tuning nanocarbons for desired attributes. We introduce new methodologies including exciting synergistic effects, synchronizing atomic vibrations, active screen plasma, energy-driven transformations, surface acoustic micro/nano-manipulation, doping and directed self-assembly to expose relationships and integrate insights into the inverse design flow. This research promises to accelerate discovery of next-generation low-dimensional nanocarbons with exceptional properties and applications.

Structural self-organizing and pattern formation are universal and key phenomena observed during growth and cluster-assembling of the carbyne-enriched nanostructured metamaterials at the ion-assisted pulse-plasma deposition. Fine tuning these universal phenomena opens access to designing the properties of the growing carbyne-enriched nano-matrix. The structure of bonds in the grown carbyne-enriched nano-matrices can be programmed by the processes of self-organization and auto-synchronization of nanostructures. We propose the innovative concept, connected with application of the universal Cymatics phenomena during the predictive growth of the carbyne-enriched nanostructured metamaterials. We also propose the self-organization approach for increase stability of the long linear carbon chains. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon and their distribution by the spatial structure and properties of the nanostructured metamaterial grows region through the new synergistic effect. Mentioned effect will be provided through the vibration-assisted self-organized wave patterns excitation along with simultaneous manipulating by their properties through the electric field. We propose to use acoustic activation of the plasma zone of nano-matrix growing. Interaction between the inhomogeneous electric field distribution generated on the vibrating layer and the plasma ions will serve as the additional energizing factor controlling the local pattern formation and self-organizing of the nano-structures. Suggested concept makes it possible to provide precise predictive designing the spatial structure and properties of the advanced carbyne-enriched nanostructured metamaterials.

Emulsion stabilisation of base layers surfaced with chip seals often proves problematic with chips punching into the base and early distress. This can be aggravated by the use of modified binders that restricts the evaporation of moisture from pavement layers. The introduction of New-age (Nano) Modified Emulsion (NME) stabilisation has the advantage that water is chemically repelled from the stabilised layer resulting in an accelerated development of strength. A need was identified to evaluate the early life performance of selected chip seals, together with identified binders. Three different chip seal surfacings with unconventional modified binders were constructed and evaluated using Accelerated Pavement Testing (APT) with the MMLS3. The objectives of the experimental design and testing were to evaluate binder performance, early loss of chips before chip orientation at low temperatures, punching of the chips into the NME stabilised base, deformation characteristics of a Cape seal and the effect of the use of a standard normal modified binder. This paper contains details of the NME base layer, the binder and seal selection and the test results. It is shown that a cost-effective thin chip seal in combination with a suitable binder can be used on a NME stabilised base with confidence.

The use of naturally available materials not conforming to traditional specifications or standards, in the base and sub-base layers of road pavement structures, stabilised with New-age (Nano) Modified Emulsions (NME), have been tested, implemented and successfully verified through Accelerated Pavement Testing (APT) in South Africa. This was made possible through the development and use of a design procedure addressing fundamental principles and based on scientific concepts, which are universally applicable. The understanding of and incorporation of the chemical interaction between the mineralogy of the materials and a NME stabilising agent (compatibility between the chemistry of the reactive agents and material mineralogy) into the design approach is key to achieving the required engineering properties. Stabilised materials evaluation is done using tests indicative of the basic engineering properties (physics) of compressive strengths, tensile strengths and durability. This article describes the basic materials design approach developed to ensure that organofunctional nano-silane modified emulsions can successfully be used for pavement layer construction utilising naturally available materials, at a low risk. The enablement of the use of naturally available materials in all pavement layers can have a considerable impact on the unit cost and life-cycle costs of road transportation infrastructure. TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back

Power sources that can consistently deliver high levels of energy over extended periods are crucial for various space applications. Among the many methods of energy generation, direct heat-to-electricity conversion without intermediate steps or moving components shows particular promise but also presents significant challenges. The aim of this research is to address these challenges by enhancing the energy efficiency of thermionic conversion, which transforms thermal energy into electrical energy, through the development and utilization of a novel class of emission nanomaterials known as multilayer carbyne-enriched 3D-shaped nano-interfaces. By manipulating the topological, physicochemical, and functional characteristics of these interfaces, we seek to optimize their thermionic conversion capabilities. Building on the recent discovery of collective atomic vibrations called phonon waves within transition domains of multilayer nanostructures, we have devised a new approach to enhance the efficiency of thermionic energy converters. This involves unlocking the predictive functionality of 2D-ordered linear-chain carbon-based multilayer emitters through the excitation and fine-tuning of collective atomic vibrations and nanoarchitecture. To achieve this, we propose employing a combination of techniques that leverage interface effects, enable phonon wave propagation, facilitate energy exchange, and capitalize on synergistic effects offered by the multilayer nano-enhanced interfaces. The resulting devices for thermionic energy conversion have the potential to significantly surpass the efficiency of existing plasma thermionic converters by several orders of magnitude. Moreover, these electricity-generating sources based on thermionic conversion represent fundamental options for the advancement of Lunar and Martian research missions, opening up possibilities for sustainable energy production in extraterrestrial environments.

: Nanotechnology options to road surface maintenance offers several advantages compared to traditionally used materials. The small particle sizer of hydrophobic Nano-Silane modified Nano-Polymers (NSNP) enables these nanotechnology products to deeply penetrate existing road surfaces, sealing micro-cracks and render surfacings to be water-resistant for extended periods of time. In comparison, traditionally used products contain minimum partial sizes of about 1 – 5 microns, that provide a superficial protection that wears off in a relatively short period of time. These traditional products are often associated with vehicle contamination while drying and requires the re-instatement of road markings. None of these disadvantages are associated with applicable NSNP technologies that are quick drying, with no vehicle contamination risks and is equivalent to a “clear-seal” requiring no reinstatement of road markings. In a similar vein, pot-hole repairs can be done using applicable, easy to use, pre-packed and treated pot-hole repair kits that are water-repellent and quick-drying at a fraction of the costs of conventional cold-mix products. Resurfacing using NME binder slurries can be done labour-intensively on a pre-treated NSNP surfacing, restoring cracked surfacing and providing a water-resistant long-lasting protective layer without the removal of existing cracked areas. The implementation of nanotechnology solutions for road surface maintenance operations is directly associated with ease of use, labour-intensive operations, prevention of considerable deterioration in riding quality due to removal and manual re-instatement of cracked surfaces, time and cost savings and a reduction in the risk of water damage to the sub-structure. TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back TRANSLATE with x English ArabicHebrewPolish BulgarianHindiPortuguese CatalanHmong DawRomanian Chinese SimplifiedHungarianRussian Chinese TraditionalIndonesianSlovak CzechItalianSlovenian DanishJapaneseSpanish DutchKlingonSwedish EnglishKoreanThai EstonianLatvianTurkish FinnishLithuanianUkrainian FrenchMalayUrdu GermanMalteseVietnamese GreekNorwegianWelsh Haitian CreolePersian TRANSLATE with COPY THE URL BELOW Back EMBED THE SNIPPET BELOW IN YOUR SITE Enable collaborative features and customize widget: Bing Webmaster Portal Back

Backward electromagnetic waves are extraordinary waves with contra-directed phase velocity and energy flux. Unusual properties of the coherent nonlinear optical coupling of the phase-matched ordinary and backward electromagnetic waves with contra-directed energy fluxes are described which enable greatly-enhanced frequency and propagation direction conversion, parametrical amplification, as well as control of shape of the light pulses. Extraordinary transient processes that emerge in such metamaterials in pulsed regimes are described. The results of the numerical simulation of particular plasmonic metamaterials with hyperbolic dispersion are presented, which prove the possibility to match phases of such coupled guided ordinary and backward electromagnetic waves. Particular properties of the outlined processes in the proposed metamaterial are demonstrated through numerical simulations. Potential applications include ultra-miniature amplifiers, frequency changing reflectors, modulators, pulse shapers, and remotely actuated sensors.