This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

This paper presents the design of a high frequency zero voltage switching (ZVS) full-bridge converter with a phase-shifted driving signal for photovoltaic applications. The resonant power converter can provide high-power capacity under high-frequency operation. The proposed power converter can also reduce the size of the transformer under the same power rating. The high-frequency transformer was developed by using the resonant and switching frequencies of the power converter to reduce the switching loss and to improve the system efficiency. Phase-shifted modulation was selected to drive the switches of a full-bridge power converter based on the switching loss minimization method. The desired output voltage was controlled using a closed-loop controller under a loop gain stability margin. The simulation results showed that the output voltage can be controlled to the desired constant when the input voltage changes from 30 VDC to 60 VDC. The desired output voltage of power converter is constant at 400 VDC. The power converter can transfer the DC supply to a 220 VAC household via grid-connected inverter. Therefore, the proposed study showed the effectiveness of the phase-shift ZVS full-bridge power converter with high-frequency transformer. This power converter can control the operation of the desired voltage system and has a small sizing of power converter system, low switching loss, and high system efficiency.

Frequency, amplitude and phase information of the grid voltage are of great importance in constructing a robust controller structure for grid connected inverter systems. This paper presents a simple and robust approach for the instantaneous estimation of positive and negative sequence voltage components under distorted voltage conditions. A second order generalized integrator (SOGI) is used to filter the distorted voltage and to generate orthogonal voltage components for each of the three phases. These filtered and orthogonal components are used for instantaneous calculation of symmetrical components. The implemented method is frequency adaptive; the method is demonstrated and compared to a conventional phase locked loop (PLL) technique with both MATLAB/Simulink simulations and experiments utilizing the dSPACE ds1103 digital controller.

Modulation of the amplitude of high-frequency cortical field activity locked to changes in phase of a slower brain rhythm is known as phase-amplitude coupling (PAC). The study of this phenomenon has been gaining traction in neuroscience because of several reports on its appearance in normal and pathological brain processes in humans as well as across different mammalian species. This has led to the suggestion that PAC may be an intrinsic brain process that facilitates brain inter-area communication across different spatiotemporal scales. Several methods have been proposed to measure the PAC process, but few of these enable detailed study of its time course. It appears that no studies have reported details of PAC dynamics including its possible directional delay characteristics. Here, we study and characterize the use of a novel information theoretic measure that may address this limitation: local transfer entropy. We use both simulated and actual intracranial electroencephalographic data, and in both cases we observe initial indications that local transfer entropy can be used to detect the onset and offset of modulation process periods revealed by mutual information phase-amplitude coupling (MIPAC). We review our results in the context of current theories about PAC in brain electrical activity, and discuss technical issues that must be addressed to see local transfer entropy more widely applied to PAC analysis.

Bartonella henselae is a fastidious Gram-negative intracellular bacterium which can cause cat scratch disease, endocarditis in humans and animals as well as other complications, leading to acute or chronic infections. The current treatment for Bartonella infections is not very effective due to antibiotic resistance and also persistence. To develop better therapies for persistent and chronic Bartonella infections, in this study, with the help of SYBR Green I/PI viability assay, we performed a high-throughput screening of an essential oil library against stationary phase B. henselae. We successfully identified 32 essential oils that had high activity, including four essential oils extracted from Citrus plants, three from Origanum, three from Cinnamomum, two from Pelargonium and two from Melaleuca, as well as frankincense, ylang ylang, fir needle, mountain savory (winter), citronella, spearmint, elemi, vetiver, clove bud, allspice and cedarwood essential oils. The minimal inhibitory concentration (MIC) determination of these 32 top hits indicated they were not only active against stationary phase non-growing B. henselae but also had good activity against log phase growing B. henselae. The time-kill curve by drug exposure assay showed 13 active hits, including essential oils of oregano, cinnamon bark, mountain savory (winter), cinnamon leaf, geranium, clove bud, allspice, geranium bourbon, ylang ylang, citronella, elemi and vetiver, could eradicate all stationary phase B. henselae cells within 7 days at the concentration of 0.032% (v/v). Two active ingredients, carvacrol and cinnamaldehyde, of oregano and cinnamon bark essential oils, respectively, were shown to be very active against stationary phase B. henselae such that they were able to eradicate all the bacterial cells even at the concentration ≤ 0.01% (v/v). Our finding of active essential oils may help to develop more effective treatments for persistent Bartonella infections.

This thesis completion works it out to deepen into diverse modeling techniques for Point Absorbers. A combined frequency-time domain model is conceived, designed and developed in Matlab with FoRtran as a base., leading to obtain physical variables of primary importance, namely position, velocity and power to Energy net balance relationships of absorption. Integration of different degrees of freedom with heave as main executable leads in turn to a single buoy motion focus. Acquisition of the needed hydrodynamic coefficients is provided though application of NEMOH & BEMIO solvers due to the Boundary Element Methodology. Initially, this Wave-to-motion model is validated through comparison with previous experimental results for a floating cone cylinder shape (Buldra-FO3). A single, generic, vertical floating cylinder is contemplated then, that responds to the action of the passing regular waves excitation. Later, two equally sized vertical floating cylinders aligned with the incident wave direction are modeled for a variable distance between the bodies. For both unidirectional regular and irregular waves as an input in deep water, we approximate the convolutive radiation force function term through the Prony method. By changing the spatial disposition of the axisymmetric buoys, using for instance triangular or rectangular shaped arrays of three and four bodies respectively, the study delves into motion characteristics for regular waves. The results highlight efficient layouts for maximizing the energy production whilst providing important insights into their performance, revealing displacement amplification- and capture width-ratios, while deriving in possible interpretations of scenarios related to the the known park effect. These terms are encompassed by the novelty of a new conceptual Post-Processing methodology in the field, which leads to obtain an optimal distance for the separated bodies with effective energy absorption in a regular wave regime. In conclusion, this computational excursion envisions and proposes potentials fields of study, which will surely enhance new connections and link this renewable energy form.

Polyhydroxyalcanoates (PHAs) are biodegradable polymers synthesized in cytoplasmic granules in bacteria, such as Cupriavidus necator (Ralstonia eutropha), Alcaligenes latus, Pseudomonas spp., Comamonas spp. and other species. PHAs accumulation occurs in response to stress conditions, i.e. under high carbon and low nitrogen (24:1 ratio). PHA can be synthesized using recombinant microorganisms (provided with the operon phbA/phbB/phbC), escaping the constrains of nutrient request, except addition of high amount of sugar (glucose, lactose, fructose). In this study; E. coli was genetically modified for PHB production in biofermentors. The production of PHA at industrial scale requires a continuous supplementation of fermentable sugars to support the availability of nutrients and to assess the level of the exponential growth phase; since sugars are required either for bacterial growth either for PHA synthesis and energy storage. The biofermentors need to be run in automated system. Sensors are used at many points in fermentators; in the evaluation of parameters: consumption of sugars; cell density; quantification of PHB synthesis. The need of operational control during the fermentation has prompted us to application of three measurements; one unit linked to a Nanodrop to evaluate OD; one linked to a reaction chamber to measure sugars consumed by enzyme based fluorescence detection; and one for bacteria Nile Blue staining and fluorescence intensity reads. The growth of bacteria on three different plant by-products was monitored and PHB production in four days using a banana by-product feed was optimised. These detectors will make possible to exploit the full potential of bioreactors optimizing the time of use and maximizing the number of bacteria synthesizing PHA.

The theory and working principle of fabric phase sorptive extraction (FPSE) is presented that eloquently explains the mystery behind this new and powerful sample preparation technique. FPSE innovatively integrates the benefits of sol-gel coating technology and the rich surface chemistry of cellulose/polyester/fiberglass fabric, resulting in a microextraction device with very high sorbent loading in the form of an ultra-thin coating. This porous sorbent coating and the permeable substrate synergistically facilitate very fast extraction equilibrium. The flexibility of the FPSE device allows for direct insertion into original, unmodified samples of different origin. Strong chemical bonding between the sol-gel sorbent and the fabric substrate permits the exposure of FPSE devices to any organic solvent for analyte back-extraction/elution and to highly acidic or basic environments (pH 1-12) if required. A sol-gel derived sorbent, highly polar sol-gel poly(ethylene glycol) coating, was generated on cellulose substrates. Five cm2 segments of these coated fabrics were used as the FPSE devices for sample preparation using direct immersion. An important class of environmental pollutants, substituted phenols, was used as model compounds to evaluate the extraction performance of FPSE. The high primary contact surface area (PCSA) of the FPSE device and porous structure of the sol-gel coatings resulted in very high sample capacities and incredible extraction sensitivities for both the compound classes in a relatively short period of time. Different extraction parameters were evaluated and optimized. The new extraction devices demonstrated part per trillion level detection limits for substituted phenols, a wide range of detection linearity, and good performance reproducibility.

When focusing on materials science in civil engineering, the current trend is to investigate the use of innovative solutions in order to enhance thermal and energy performances. This trend is amplified with the need for a sustainable development strategy for the construction sector. This paper assesses the integration of a Phase Change Material (PCM) in cement intended for building construction. The key characteristic of PCMs is their capacity to absorb energy and restore it. In building construction, this feature could be harnessed to save energy by incorporating PCMs in the materials used. In this study, passive integration of PCM in cement was tested and thermal properties of such an integration was assessed. The results provide insights into how PCMs affect cement as part of the concrete mixture, thus identifying the contribution of PCM-based cements in concrete mixtures.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

Hierarchical tungsten oxide assemblies such as spindle-like, flowers with sharp petals, nanowires and regular hexagonal structures are successfully synthesized via a solvothermal reduction method by simply adjusting the reaction conditions. On the basis of the experimental results, it is determined that the reaction time significantly influences the phase transition, microstructure and photocatalytic activity of the prepared samples. The possible mechanisms for the phase transition and morphology evolution process have been systematically proposed. Moreover, the as-prepared products exhibit significant morphology-depended photocatalytic activity. The flower-like W18O49 prepared at 6 h possesses large specific surface area (150.1 m²g^-1), improved separation efficiency of electron-hole pairs and decreased electron-transfer resistance by the photoelectrochemical measurements. As a result, the flower-like W₁₈O₄₉ prepared at 6 h exhibits the highest photocatalytic activity for the degradation of Methyl orange aqueous solution. The radical trap experiments showed that the degradation of MO was driven mainly by the participation of h⁺ and •O²⁻ radicals.

Chemical analysis of the organic components in beers has applications to quality control, authenticity and improvements to the flavor characteristics and brewing process. This study aims to show the complementary nature of two instrumental techniques which in combination can identify and quantify the majority of organic components in a beer sample. Nuclear Magnetic Resonance (NMR) was used to provide concentrations of twenty five different organic compounds including alcohols, organic acids, carbohydrates, and amino acids. Calorie content was also estimated for the samples. NMR data for ethanol concentrations were validated by comparison to a Fourier Transform Infrared Spectrometry (FTIR) method. Headspace Solid-Phase Microextraction (SPME) Gas Chromatography Mass Spectrometry (GCMS) was used to identify a range of volatile compounds such as alcohols, esters and hop derived aroma compounds. A simple and inexpensive conversion of a Gas Chromatography Flame Ionization Detector (GC FID) instrument to allow the use of Solid-Phase Microextraction was found to be useful for the quantification of volatile esters.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

Background: Pittosporum tobira (Thunb.) Aiton is an aromatic medicinal plant widely cultivated in the world. However, the essential oils (EOs) from P. tobira flowers for anti-cancer potential is still not systematically studied. The present aim to elucidate the phytochemical composition of the EOs and to explore mechanism of anticancer action. Methods: The EOs were extracted and analyzed by headspace solid-phase microextraction (HS-SPME) with gas chromatography-mass spectrometry (GC-MS). Volatile components were identified according to Kovats retention index (KI) and NIST database. The anti-neoplasm mechanisms of the EOs was comprehensively investigated in lung carcinoma A549 and H460 cells. Results: A total of 47 secondary metabolites representing 94.18% of the EOs were successfully identified: monoterpenes and sesquiterpenes were the dominant terpenoids. The EOs exhibited antiproliferative activity on A549 and H460 lung carcinoma cells. Hoechst 33324 fluorescent staining indicated the typical characteristics of apoptosis and induced cycle phase arrest. AnnexinV/PI staining revealed that the number of apoptotic cells was increased. Furthermore, the EOs also induced the caspase-mediated mitochondrial apoptosis pathway. Conclusions: Findings suggest that the full-scale chemical composition and first characterization of anticancer activities of the EOs, it could be used for integrative natural anti-cancer agents in health care should be pay more attention.

This article attempts to formulate a mathematical model for a potential explanation regarding the unavoidable impact of a rigid body's peculiar shape on the seamless flow over it. The solid body completely immersed in a Newtonian fluid and respectively has a relative open circuit flow on it will typically experience various observable phenomena like flow separation, flow transition, down-wash, stalling at the higher angle of attack, stalling velocity and how cambered airfoil can typically generate lift at a zero incidence angle. This article respectively represents an understanding of the laminar flow over a rigid body's external surface with due respect to its distinctive shape and size. This working paper formulates a more realistic and simplified mathematical model for open circuit laminar flow over a body, based on the historical data of aerodynamics and theoretical mechanics. This is intended to properly estimate forces on the continuous surface of the body in a laminar flow, to properly explain, understand and predict mentioned phenomena. Most of all the mechanism of streamline formation and its deformation with due regards to flow, shape and size of the body in an open-circuit laminar are formulated mathematically to enhance better design theory which can reduce experimentation while designing a streamlined body.

This research is related to the eco-hydrological problems of herbaceous wetland drying and biodiversity loss in the floodplain lakes of the Middle Basin of the Biebrza river (Poland). An experiment was set up, whose main goals were: (i) mapping the vegetation types and the temporarily or permanently flooded areas, and (ii) comparing the usefulness of C-band Sentinel-1A (S1A) and X-band TerraSAR-X/TanDEM-X (TSX/TDX) for mapping purposes. The S1A imagery was acquired on a regular basis using the dual polarization VV/VH and the Interferometric Wide Swath Mode. The TSX/TDX data were acquired in quad-pol, a fully polarimetric mode, during the Science Phase. The paper addresses the following aspects: i) wetland mapping with S1A multi-temporal series; ii) wetland mapping with fully polarimetric TSX/TDX data; iii) comparing the wetland mapping using dual polarization TSX/TDX subsets, i.e. HH-HV, HH-VV and VV-VH; iv) comparing wetland mapping using S1A and TSX/TDX data based on the same polarization (VV-VH); v) studying the suitability of the Shannon Entropy for wetland mapping; and vi) assessing the contribution of interferometric coherence for wetland classification. The experimental results show main limitations of the S1A dataset, while they highlight the good accuracy that can be achieved using the TSX/TDX data, especially those taken in fully polarimetric mode.

Gray cast iron is one of the most important engineering materials that has many applications in various industries including automotive and machinery manufacturing due to its mechanical properties, wear resistance, machining potentials and low price. In this research effect of adding aluminum and silicon to composition of gray cast iron on microstructure and wear resistance was studied. Moreover, it was investigated the role of formation of Fe-Al-Si intermetallic compound in final properties of the alloy. For studying wear resistance of samples pin-on-disc method was carried out. The results showed that addition of aluminum to gray cast iron causes formation of ferrite matrix, which leads to a decrease in hardness value. Increasing silicon content up to 2 wt. % in cast iron with 4 wt. % aluminum intensifies the formation of ferrite matrix, while further increase to 3 wt. % causes emerging a Fe-Al-Si intermetallic phase. Improvement in hardness value was achieved by increasing silicon content from 3 wt. % to 4 wt. % due to the increased percentage of intermetallic phase. Effect of intermetallic phase on decreasing wear rate was showed by studying microstructure and hardness values, however the lowest wear resistance was observed in aluminum bearing cast iron containing 2 wt. % silicon.

This work intends to present a study on relations between a Lie algebra called dispersion operators algebra, linear canonical transformation and a phase space representation of quantum mechanics that we have introduced and studied in previous works. The paper begins with a brief recall of our previous works followed by the description of the dispersion operators algebra which is performed in the framework of the phase space representation. Then, linear canonical transformations are introduced and linked with this algebra. A multidimensional generalization of the obtained results is given.

Quantitative phase microscopy (QPM), a technique combining phase imaging and microscopy, enables visualization of the 3-D topography in reflective samples as well as the inner structure or refractive index distribution of transparent and translucent samples. However, as in conventional optical microscopy, QPM provides either a large field of view (FOV) or a high resolution but not both. Many approaches such as oblique illumination, structured illumination and speckle illumination have been proposed to improve the spatial resolution of phase microscopy by restricting other degrees of freedom (mostly time). Therefore, the space bandwidth product (SBP) of QPM becomes enlarged. This paper aims to provide an up-to-date review on the resolution enhancement approaches of QPM, discussing the pros and cons of each technique as well as the confusion on resolution definition claim on QPM and other coherent microscopy.

That how to improve the sensitivity and the detection ability of the Large-caliber sensor is critical to satisfy the requirement of heavy vehicle wear condition monitoring. In this paper, we introduced the LC resonance principle to the design of sensor with large flow channel (7mm). The resonant exciting coil increases the impedance change of the exciting circuit caused by wear particles which magnify the current difference between the two exciting coils and improve the sensitivity of the sensor. The resonant induction coil greatly suppresses the interference signals and magnifies the weak induced electromotive force which is beneficial to enhance the detection ability. In order to boost the detectability for different materials particles, a phase controlled variable-frequency exciting system (PCVFES) was adopted to automatically switch the exciting frequency between 284kHz for ferromagnetic particles and 420KHz for non-ferromagnetic particles. For the weak signal detection, based on the essential characteristic of the signal, we apply a simpler method that modified lock-in amplifier (MLIA) rather than the conventional algorithms (Wavelet transform, EMD). Results show that using these methods the sensitivity and the detection ability of the sensor are significantly improved and the 75μm iron particles and 220μm copper particles were successfully detected which realizes the initial abnormal wear monitoring for the large flow project.

In this paper, a new approach to the sliding-mode control of single-phase inverters under linear and non-linear loads is introduced. The main idea behind this approach is to utilize a non-linear, flexible and multi-slope function in controller structure. This non-linear function makes the controller possible to control the inverter by a non-linear multi-slope sliding surface. In general, this sliding surface has two parts with different slopes in each part and the flexibility of the sliding surface makes the multi-slope sliding-mode controller (MSSMC) possible to reduce the total harmonic distortion, to improve the tracking accuracy, and to prevent overshoots leading to undesirable transient-states in output voltage which are occurred when the load current sharply rises. In order to improve the tracking accuracy and to reduce the steady-state error, an integral term of the multi-slope function is also added to the sliding surface. The improved performance of the proposed controller is confirmed by simulations and finally, the results of the proposed approach are compared with a conventional SMC and a SRFPI controller.

Numerical models widely used for hydrocarbon phase behavior and compositional flow simulations are based on assumption of thermodynamic equilibrium. However, it is not uncommon for oil and gas-condensate reservoirs to exhibit essentially non-equilibrium phase behavior, e.g., in the processes of secondary recovery after pressure depletion below saturation pressure, or during gas injection, or for condensate evaporation at low pressures. In many cases the ability to match field data with equilibrium model depends on simulation scale. The only method to account for non-equilibrium phase behavior adopted by the majority of flow simulators is the option of limited rate of gas dissolution (condensate evaporation) in black oil models. For compositional simulations no practical yet thermodynamically consistent method has been presented so far except for some upscaling techniques in gas injection problems. Previously reported academic non-equilibrium formulations have a common drawback of doubling the number of flow equations and unknowns compared to the equilibrium formulation. In the paper a unified thermodynamically-consistent formulation for compositional flow simulations with non-equilibrium phase behavior model is presented. Same formulation and a special scale-up technique can be used for upscaling of an equilibrium or non-equilibrium model to a coarse-scale non-equilibrium model. A number of test cases for real oil and gas-condensate mixtures are given. Model implementation specifics in a flow simulator are discussed and illustrated with test simulations. A non-equilibrium constant volume depletion algorithm is presented to simulate condensate recovery at low pressures in gas-condensate reservoirs. Results of satisfactory model matching to field data are reported and discussed.

This paper investigates the tank drainage problem of an isothermal, unsteady, incompressible electrically conducting Power law fluid. Analytic solution have been obtained from governing continuity and momentum equations subject to appropriate boundary conditions by using Perturbation method. The Power law fluid model solution without MHD is retrieved from this proposed model on substitution . Declaration on behalf of velocity profile, volume flux, average velocity, connection of time with respect to length of the tank and requirement of time for whole drainage of fluid are acquired. Special effects of numerous emerging parameter’s on velocity profile vz and depth of the fluid in the tank are graphically presented. Keywords: Tank drainage, Power law MHD fluid, Analytical solution.

Different notions of entropy can be identified in different communities: (i) the thermodynamic sense, (ii) the information sense, (iii) the statistical sense, (iv) the disorder sense, and (v) the homogeneity sense. Especially the “disorder sense” and the “homogeneity sense” relate to and require the notion of space and time. One of the few prominent examples relating entropy to geometry and to space is the Bekenstein-Hawking entropy of a Black Hole. Although being developed for the description of a physics object—a black hole—having a mass, a momentum, a temperature, a charge etc. absolutely no information about these attributes of this object can eventually be found in the final formula. In contrast, the Bekenstein-Hawking entropy in its dimensionless form is a positive quantity only comprising geometric attributes like an area A—which is the area of the event horizon of the black hole-, a length L_P—which is the Planck length - and a factor ¼. A purely geometric approach towards this formula will be presented. The approach is based on a continuous 3D extension of the Heaviside function, with this extension drawing on the phase-field concept of diffuse interfaces. Entropy enters into the local, statistical description of contrast respectively gradient distributions in the transition region of the extended Heaviside function definition. The structure of the Bekenstein-Hawking formula eventually is derived for a geometric sphere based on mere geometric-statistic considerations.

Owing to the nondiffracting, self-accelerating, and self-healing properties, Airy beams of different nature have become a subject of immense interest in the past decade. Their interesting properties have opened doors to many diverse applications. Consequently, the questions of how to properly design spatial manipulation of Airy beams or how to implement them in different setups have become important and timely in the development of various optical devices. Here, based on our previous work, we present a short review on the spatial control of Airy beams, including the interactions of Airy beams in nonlinear media, beam propagation in harmonic potential, and the dynamics of abruptly autofocusing Airy beams in the presence of a dynamic linear potential. We demonstrate that under the guidance of nonlinearity and external potential, the trajectory, acceleration, structure, and even the basic properties of Airy beams can be adjusted to suit specific needs. We describe other fascinating phenomena observed with Airy beams, such as self-Fourier transformation, periodic inversion of Airy beams, and the appearance of spatial solitons in the presence of nonlinearity. These results have promoted the development of Airy beams, and have been utilized in various applications, including particle manipulation, self-trapping, and electronic matter waves.

The evolving multiphase induction generators (MPIG) with more than three phases are receiving prominence in high power generation systems. This paper aims at the development of a comprehensive model of the wind turbine driven seven-phase induction generator (7PIG) along with necessary the power electronic converters and controller for grid interface. The dynamic model of the system is developed in Maltlab/Simulink. Synchronous reference frame phase-locked loop (SRFPLL) system is incorporated for grid synchronization. The modeling aspects are detailed and the system response is observed for various wind velocities. The effectiveness of seven phase induction generator is demonstrated with the fault tolerant capability and high output power with reduced phase current when compared to conventional 3-phase wind generation scheme. The response of the PLL is analyzed and the results are presented.

Cancers are complex, adaptive ecosystems. They remain the leading cause of disease-related death among children in North America. As we approach computational oncology and Deep Learning Healthcare, our mathematical models of cancer dynamics must be revised. Recent findings support the perspective that cancer-microenvironment interactions consist of turbulent flows. As such, cancer pattern formation, protein-folding and metastatic invasion are discussed herein as processes driven by chemical turbulence within the framework of complex systems theory. Current state-of-the-art quantitative approaches used in reconstructing cancer stem cell networks are reviewed. To conclude, cancer stem cells are presented as strange attractors of the Waddington landscape.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

The parameter estimation problem for polynomial phase signals (PPSs) arises in a number of fields, including radar, sonar, biology, etc. In this paper, a fast algorithm of parameter estimation for monocomponent PPS is considered. We propose the so-called LSU-EKF estimator, which combines the least squares unwrapping (LSU) estimator and the extended Kalman filter (EKF). First, the coarse estimates of the parameters of PPS are obtained by the LSU estimator using a small number of samples. Subsequently, these coarse estimates are used to initial the EKF. Monte-Carlo simulations show that the computation complexity of the LSU-EKF estimator is much less than that of the LSU estimator, with little performance loss. Similar to the LSU estimator, the proposed algorithm is able to work over the entire identifiable region. Moreover, in the EKF stage, the accurate estimated results can be output point-by-point, which is useful in real applications.

Titanium dioxide (TiO₂) micro and nano architectures have been intensively studied in the past years because of many varied applications in environmental, energy conversion, and storage fields, such as heterogeneous catalysis, dye-sensitized solar cells, lithium/sodium ion batteries, lithium-sulfur (Li-S) batteries, and bio-nanotechnology, etc. Especially the surface and interface structures in the TiO₂ structures play important roles in those applications. This mini review article focuses on TiO₂ micro and nano architectures with the prevalent crystal structures (anatase, rutile, brookite, and TiO₂(B)), and summarizes major advances in the surface and interface engineering and applications in environmental and electrochemical applications. We present the principles and growth mechanisms of TiO₂ nanostructures via different strategies, with an emphasis on rational control of the surface and interface structures. We further discuss the applications of TiO₂ micro and nano architectures in photocatalysis, lithium/sodium ion batteries, and Li-S batteries. Throughout the discussion, the relationship between the device performance and the surface structures of TiO₂ micro/nano structures will be highlighted. Then we discuss the phase transitions of TiO₂ nanostructures and possible strategies of improving the phase stability. The review concludes with a perspective on the current challenges and future research directions.

The Koka gold deposit is located in the Elababu shear zone between the Nakfa terrane and the Adobha Abiy terrane, NW Eritrea. Based on the paragenetic study two main stages of gold mineralization were identified in the Koka gold deposit: 1) an early stage of pyrite-chalcopyrite-sphalerite-galena-gold-quartz vein; and 2) a second stage of pyrite-quartz veins. NaCl-aqueous inclusions, CO2-rich inclusions, and three-phase CO₂-H₂O inclusions occur in the quartz veins at Koka. The ore-bearing quartz veins formed at 268℃, from NaCl-CO₂-H₂O(-CH₄) fluids averaging 5 wt% NaCl eq. The ore-forming mechanisms include fluid immiscibility during stage I, and mixing with meteoric water during stage II. Oxygen, hydrogen and carbon isotopes suggest that the ore-forming fluids originated as mixtures of metamorphic water, meteoric water and magmatic water, whereas sulfur isotope suggest an igneous origin. Features of geology and ore-forming fluid at Koka deposit are similar to those of orogenic gold deposits, suggesting the Koka deposit might be an orogenic gold deposit related to granite.

We consider the financial planning problem of a retiree wishing to enter a retirement village at a future uncertain date. The date of entry is determined by the retiree's utility and bequest maximisation problem within the context of uncertain future health states. In addition, the retiree must choose optimal consumption, investment, bequest and purchase of insurance products prior to her full annuitisation on entry to the retirement village. A hyperbolic absolute risk-aversion (HARA) utility function is used to allow necessary consumption for basic living and medical costs. The retirement village will typically require an initial deposit upon entry. This threshold wealth requirement leads to exercising the replication of an American put option at the uncertain stopping time. From our numerical results, active insurance and annuity markets are shown to be a critical aspect in retirement planning.

It is strongly desirable to accurately detect the clouds in hyperspectral images onboard before compression. However, conventional onboard cloud detection methods are not appropriate to all situation such as shadowed cloud or darken snow covered surfaces which are not identified properly in the NDSI test. In this paper, we propose a new spectral–spatial classification strategy to enhance the orbiting cloud screen performances obtained on hyperspectral images by integrating threshold exponential spectral angle map (TESAM), adaptive Markov random field (aMRF) and dynamic stochastic resonance (DSR). TESAM is performed to classify the cloud pixels coarsely based on spectral information. Then aMRF is performed to do optimal process by using spatial information, which improved the classification performance significantly. Some misclassification points still exist after aMRF processing because of the noisy data in the onboard environment. DSR is used to eliminate misclassification points in binary labeling image after aMRF. Taking level 0.5 data from hyperion as dataset, the average overall accuracy of the proposed algorithm is 96.28% after test. The method can provide cloud mask for the on-going EO-1 images and related satellites with the same spectral settings without manual intervention. The experiment indicate that the proposed method reveals better performance than the classical onboard cloud detection or current state-of-the-art hyperspectral classification methods.

Fabric phase sorptive extraction (FPSE) combines the advanced material properties of sol–gel derived microextraction sorbents and the flexible and permeable fabric support to create a robust, simple and green sample preparation device. It simultaneously improves the extraction sensitivity, and the speed of the extraction by incorporating high volume of sponge-like porous sol–gel hybrid inorganic–organic sorbents into permeable fabric substrates that is capable of extracting target analytes directly from simple to complex aqueous sample matrices. For the first time, this technique was applied to the trace level determination of selected polycyclic aromatic hydrocarbons (PAHs) in environmental water samples using a non-polar sol–gel C18 coated FPSE media. Several extraction parameters were optimized to improve extraction efficiency and to achieve high detection sensitivity. Validation tests of spiked samples showed good linearity for four selected PAHs (R² = 0.9983–0.9997) over a wide range of concentrations (0.010-10 ng/mL). Limits of detection (LODs) and quantification (LOQs) were measured at pg/mL levels, 0.1–1 pg/mL and 0.3–3 pg/mL, respectively. Inter- and intra-day precision tests showed variations of 1.1–4.1% for four selected PAHs. Average absolute recovery values were in the range of 88.1–90.5% surpassed the recovery prediction model, with relative standard deviations below 5%. The developed FPSE-HPLC-FLD protocol was finally applied to analyze 8 environmental water samples. Out of four selected PAHs, fluoranthene (Flu) and phenanthrene (Phen) were the most frequently detected in four samples, at concentration levels of 5.6–7.7 ng/mL and 4.1-11 ng/mL, respectively followed by anthracene (Anth) and pyrene (Pyr) in two samples. The newly developed FPSE-HPLC-FLD protocol is simple, green, fast and economical, with adequate sensitivity for trace levels of four selected PAHs and seems to be promising in routine monitoring of water quality and safety.

This compendium presents new mathematical techniques for modeling Point Absorbers. A combined frequency-time domain framework is developed. It is used to simulate the energy generated by the wave farms. With Matlab and Fortran as a base, this leads to obtain physical variables of primary importance, namely position, velocity and power to energy net balance relationships of absorption. Integration of different degrees of freedom with heave as main executable leads in turn to a single buoy motion focus. Acquisition of the needed hydrodynamic coefficients is provided through application of potential field solvers with Boundary Element Methodology background. Initially, this Wave-to-motion model is validated by comparison with previous experimental results for a floating cone cylinder shape (Buldra-FO3). A single, generic, vertical floating cylinder is contemplated then, that responds to the action of the passing regular waves excitation. Later, two equally sized vertical floating cylinders aligned with the incident wave direction are modeled for a variable distance between the bodies. For both unidirectional regular and irregular waves as an input in deep water, we approximate the convolutive radiation force function term through the Prony method. By changing the spatial disposition of the axisymmetric buoys, using for instance triangular or rectangular shaped arrays of three and four bodies respectively, the study delves into motion characteristics for regular waves. The results highlight efficient layouts for maximizing the energy production whilst providing important insights into their performance, revealing displacement amplification- and capture width-ratios, while deriving in possible interpretations of scenarios related to the known park effect. These terms are encompassed by the novelty of a new conceptual Post-Processing methodology in the field, which leads to obtain an optimal distance for the separated bodies with effective energy absorption in a regular wave regime. The main objective is to generate a tendency within the hydrodynamic field of study, which is the Wave to motion perspective. More generally, this computational excursion envisions and depicts potential fields of study, which will surely enhance new connections and link this renewable energy form. Therefore, this research delves first into the historical and technical background on Ocean Wave Energy. Next, it is in the section regarding Materials and Methods, where boundaries and related equations are introduced step by step, together with latter mentioned case scenarios, and their corresponding configuration parameters. A separate section frames then the scope of results, while finally, there is an ensuing discussion and conclusions for evaluation assessment.

Terms related to gradients of scalar fields are introduced as scalar products into the formulation of entropy. A Lagrange density is then formulated by adding constraints based on known conservation laws. Applying the Lagrange formalism to the resulting Lagrange density leads to the Poisson equation of gravitation and also includes terms being related to curvature of space. The formalism further leads to terms possibly explaining nonlinear extensions known from modified Newtonian dynamics approaches. The article concludes with a short discussion of the presented methodology and provides an outlook on other phenomena, which might be tackled using this new approach.

The present review paper aims at collecting and discussing the research work, numerical and experimental, carried out in the field of Fluid-Structure Interaction (FSI) in one-dimensional (1D) pressurized transient flow in the time-domain approach. Background theory and basic definitions are provided for the proper understanding of the assessed literature. A novel frame of reference is proposed for the classification of FSI models based on pipe degrees-of-freedom. Numerical research is organized according to this classification, while an extensive review on experimental research is presented by institution. Engineering applications of FSI models are described and historical accidents and post-accident analyses documented.

With large-scale distributed generators (DGs) in an active distribution network (ADN), conventional load flow convergence failure is incurred by heavy power transmission. The Holomorphic Embedding Load Flow Method (HELM) has proven to be more robust than the Newton–Raphson method under heavy power transmission. At present, HELM is mainly designed for balanced transmission networks. In this study, we developed a three-phase HELM model to accommodate DGs, delta connection loads, and ZIP loads for ADN. The effectiveness and better performance of the proposed method under heavy load situations were validated using modified unbalanced IEEE 13, 34, 37, and 123 test feeders.

Molecularly imprinted polymers (MIPs) were synthesized and applied for the selective extraction of oblongifolin C (OC) from fruit extracts of Garcinia yunnanensis Hu. A series of experiments and computational approaches were employed to improve the efficiency of screening for optimal MIP systems in the study. The molar ratio (1:4) was chosen at last based on the comparison of the binding energy of the complexes between the template (OC) and functional monomers using density functional theory (DFT) at the RI-PBE-D3-gCP/def2-TZVP level of theory. The binding characterization and the molecular recognition mechanism of MIPs were further explained using the molecular modeling method and NMR and IR spectra data. The reusability of this approach was demonstrated in over 20 batch rebinding experiments. 140.5 mg of OC (>95% purity) was obtained from the 5 g extracts with 2 g of MIPs with the best binding properties through gradient elution program from 35% to 70% methanol-water solution. At the same time, another structural analog, 46.5 mg of guttiferone K (GK) (>88% purity), was also obtained by the gradient elution procedure. Our results showed that the structural analogs could be separated from the crude extracts by the molecularly imprinted solid-phase extraction (MISPE) using a gradient elution procedure for the first time.

The computing power of smartphones has not received considerable attention in the mainstream education system. Most of the education-oriented smartphone applications (apps) are limited to general purpose services like Massive Open Online Courses (MOOCs), language learning, and calculators (performing basic mathematical calculations). Greater potential of smartphones lies in educators and researchers developing their customized apps for learners in highly specific domains. In line with this, we present Fluid Dynamics, a highly accurate Android application for measuring flow properties in compressible flows. This app can determine properties across the stationary normal and oblique shock, moving normal shock and across Prandtl $-$ Meyer expansion fan. This app can also measure isentropic flows, Fanno flows, and Rayleigh flows. The functionality of this app is also extended to calculate properties in the atmosphere by assuming the International Standard Atmosphere (ISA) relations and also flows across the Pitot tube. Such measurements are complicated and time-consuming since the relations are implicit and hence require the use of numerical methods, which give rise to repetitive calculations. The app is an efficient semi-implicit solver for gas dynamics formulations and uses underlying numerical methods for the computations in a graphical user interface (GUI), thereby easing and quickening the learning of concerned users. The app is designed for the Android operating system, the most ubiquitous and capable surveillance platform, and its calculations are based on JAVA based code methodology. In order to check its accuracy, the app's results are validated against the existing data given in the literature.

Three-dimensional (3D) imaging has attracted more and more interests because of its widespread applications, especially in information and life science. These techniques can be broadly divided into two types: ray-based and wavefront-based 3D imaging. Issues such as imaging quality and system complexity of these techniques limit the applications significantly, and therefore many investigations have focused on 3D imaging from depth measurements. This paper presents an overview of 3D imaging from depth measurements, and provides a summary of the connection between these the ray-based and wavefront-based 3D imaging techniques.

Carbon nanomaterials with a different character of the chemical bond – graphene (sp2) and nanodiamond (sp3) are the building bricks for a new class of all-carbon hybrid nanomaterials, where the two different carbon networks with the sp3 and sp2 hybridization coexist, interact and even transform into one another. The unique electronic, mechanical, and chemical properties of the two border nanoallotropes of carbon ensure the immense application potential and versatility of these all-carbon graphene – diamond nanomaterials. The review gives an overview of the current state of the art of graphene – diamond nanomaterials, including their composites, heterojunctions, and other hybrids for sensing, electronic, energy storage, and other applications. Also, the graphene-to-diamond and diamond-to-graphene transformations at the nanoscale, essential for innovative fabrication, and stability and chemical reactivity assessment are discussed based on extensive theoretical, computational, and experimental studies.

The main objective of this communication is to describe the ‘Global Salt Cycle’. Giant salt accumulations are commonly found along continental margins of former rifts. The first stage in the accumulation process is saturation of newly formed oceanic crust with seawater. Final mobilisation and accumulation of the salts occurs during rifting, localised in the vicinity of relict subduction zones. Oceanic crust is created along the spreading ridges in the deep oceans of the Earth. It exchanges mass and energy with seawater in hydrothermal circulation cells that penetrate deep into the new and fractured crust. Water-rock interactions include the formation of hydrated and hydroxylated minerals, e.g., serpentinites and clay minerals. By incorporating hydroxyl groups and water in their crystal lattices, the salinity of remaining brines increases. Subduction of oceanic crust and serpentinised lithosphere transports water, hydrated minerals, and marine salts deep into the crust and mantle. Upon pressurisation and heating of the subducting slab, different parts of this water are expelled at different depths/temperatures. The resulting fluids will contain salts brought in with the slab, as well as new salts formed by water-rock interaction. The combination of elevated pressures and temperatures, water, salinity, and CO2, create permeability in the normally impermeable, peridotitic mantle, by altering the fluid-rock dihedral angles of mineral grains. This P/T-determined intergranular permeability allows ascent of saline fluids, under lithostatic pressure, within the mantle wedge, or the slab itself. The fluids produce a mechanically weakened and buoyant zone within the mantle wedge due to high pore pressure between mineral grains and reduced mantle density. During the lifetime of a subduction zone, a substantial accumulation of saline fluids within the mantle wedge and crust, is evident. Deep, fluid reservoirs accumulate between the subduction trench and the volcanic front. They may exist for hundreds of millions of years, even after the extinction of the subduction zone. Saline fluids may escape to the surface along deep faults, due to overfilling of available pores/fractures. Fluids within the mantle wedge may form rock melts or exist as supercritical, mineral rich fluids. The combination of reduced pressure due to rifting, and a saline and buoyant mantle, creates a mantle circulation that brings the accumulated, saline fluids, to crustal levels. Salts will therefore accumulate during initial stages of rifting as a result of massive fluid expulsion, phase change and boiling of mantle fluids. No extra energy is required to produce phase change and boiling. The result is formation of solid salts or dense brines/slurries invading fractured crustal rocks, or escaping to the surface/seabed. This process may take place both before and after the sea has invaded a continental rift.

This paper proposes a novel three-phase voltage source inverter dead-time compensation strategy for accurate compensation in wide current regions of the inverter. In particular, an analysis of the output voltage distortion of the inverter, which appears as parasitic components of the switches, has been conducted for proper voltage compensation in the low current region, and an on-line compensation voltage controller has been proposed. Also, a new trapezoidal compensation voltage implementation method using the current phase is proposed to simplify realizing the trapezoidal shape of the three-phase compensation voltages. Finally, when the proposed dead-time compensation strategy is applied, the maximum phase voltage magnitude in the linear modulation voltage regions is defined to achieve smooth operation even at high modulation index. Simulations and experiments were conducted to verify the performance of the proposed dead-time compensation scheme.

The intention of this paper is to elucidate new types of heat engines with extraordinary efficiency, more specifically to eventually focus on the author’s research into a temporary magnetic remanence device. First we extend the definition of heat engines through a diagrammatic classification scheme and note a paradoxical non-coincidence between the Carnot, Kelvin-Planck and other forms of the 2nd Law, between sectors of the diagram. It is then seen, between the diagram sectors, how super-efficient heat engines are able to reduce the degrees of freedom resulting from change in chemical potential, over mere generation of heat; until in the right sector of the diagram, the conventional wisdom for the need of two reservoirs is refuted. A brief survey of the Maxwell Demon problem finds no problem with information theoretic constructs. Our ongoing experimental enquiry into a temporary magnetic remanence cycle using standard kinetic theory, thermodynamics and electrodynamics is presented – yet a contradiction results with the 2nd law placing it in the right sector of the classification diagram.

This study presents a vibration control using actively tunable vibration absorbers (ATVA) to suppress vibration of a thin plate. The ATVA’s is made of a sandwich hollow structure embedded with the electrorheological fluid (ERF). ERF is considered to be one of the most important smart fluids and it is suitable to be embedded in a smart structure due to its controllable viscosity property. ERF’s apparent viscosity can be controlled in response to the electric field and the change is reversible in 10 microseconds. Therefore, the physical properties of the ERF-embedded smart structure, such as the stiffness and damping coefficients, can be changed in response to the applied electric field. A mathematical model is difficult to be obtained to describe the exact characteristics of the ERF embedded ATVA because of the nonlinearity of ERF’s viscosity. Therefore, a fuzzy modeling and experimental validations of ERF-based ATVA from stationary random vibrations of thin plates are presented in this study. Because Type-2 fuzzy sets generalize Type-1 fuzzy sets so that more modelling uncertainties can be handled, a semi-active vibration controller is proposed based on Type-2 fuzzy sets. To investigate the different performances by using different types of fuzzy controllers, the experimental measurements employing type-1 fuzzy and interval type-2 fuzzy controllers are implemented by the Compact RIO embedded system. The fuzzy modeling framework and solution methods presented in this work can be used for design, performance analysis, and optimization of ATVA from stationary random vibration of thin plates.

Oxidative stress negatively affects folliculogenesis and embryo development. However, a reliable and biologically accurate indicator of oxidative stress does not yet exist. On these bases, the aim of this study was to assess -and compare- blood and follicular fluid (FF) redox status in 45 infertile subjects (and 45 age-matched controls) undergoing in vitro fertilization (IVF) and to establish its connection with the outcome of IVF. Blood and FF were obtained at the time of egg retrieval and immediately analyzed. Firstly, ROS production in blood leukocytes and in granulosa cells was assessed. Oxidative stress markers in blood and in granulosa cells resulted significantly (p<0.001) increased in infertile patients compared to controls. Then, a redox index was obtained in plasma and in FF of patients and controls. The main findings emerging from our study in infertile women are: i) blood oxidative stress reflects FF oxidative stress as demonstrated by the significant correlation between blood redox markers and FF redox markers; ii) a significant correlation between oxidative stress parameters and the considered IVF outcomes is present. We suggest the strict monitoring of the redox parameters for the improvement of assisted reproductive techniques success rate and infertility management.

Building envelope can play a crucial role in building improvement efficiency and the adoption of Phase Change Materials (PCMs) coupled with transparent elements may (i) allow a better control of the heat flows from/to the outdoor environment, (ii) increase the exploitation of solar energy at building scale and (iii) modulate the light transmission to avoid glare effects. Starting from a literature review of experimental works, this research identifies the main possible integration of PCM in transparent/translucent building envelope components (in glazing, in shutters and in multilayer façade system) drawing a global picture potentials and limitations of these technologies. Transparent envelopes with PCMs have been classified from the simplest “zero” technology, which integrates the PCM into the double glass unit (DGU), to more complex solutions – with different numbers of cavities of the glass (TGU), different position of PCM layer (internal/external shutter), and in combination with other materials (TIM, aerogel, prismatic solar reflector, PCM curtain controlled by an electric pump). The results of the analysis are resumed in a SWOT (strengths, weakness, opportunities and threats) analysis table to underline strengths and weaknesses of transparent building envelope components with PCMs, and to indicate opportunities and threats for future research and building application.

Interleaved power factor correction (PFC) is widely used circuit topology due to good efficiency and power density for single-switch boost PFC. As the differential mode (DM) electromagnetic interference (EMI) noise magnitude depends upon the input current ripple, this research details a comprehensive study of DM EMI filter design for interleaved boost PFC with the aim of minimizing the component size. It is also demonstrated that the different numbers of interleaved stages and switching frequency influence the filter attenuation requirement and, thus, the EMI filter size. First, an analytical model is derived on the basis of the Norton equivalent circuit model for the differential mode noises of interleaved boost PFC within the frequency range of 9-500 kHz. The derived model can help identify the optimal phase shifting among the interleaved boost converters in order to minimize the considered differential mode noises at the filter design frequency. So, a novel phase-shift method is developed to get a minimized attenuation required by a filter in Band B. Further, a volume optimization of the required DM filter was introduced based on the calculated filter attenuation and volumetric component parameters. Based on the obtained results, unconventional and conventional phase shifts have demonstrated a good performance in decreasing the EMI filter volume in Band B and Band A, respectively. A 2-kW interleaved PFC case study is presented to verify the theoretical analyses and the impact of phase-shifting on EMI filter size.

Synthetic Aperture RADAR (SAR) is a radar imaging technique in which the relative motion of the sensor is used to synthesize a very long antenna and obtain high spatial resolution. Standard SAR raw data processing techniques assume uniform motion of the satellite (or aerial vehicle) and a fixed antenna beam pointing sideway orthogonally to the motion path, assumed rectilinear. Despite SAR data processing is a well established imaging technology that has become fundamental in several fields and applications, in this paper a novel approach has been used to exploit coherent illumination, demonstrating the possibility of extracting a large part of the ancillary data information from the raw data itself, to be used in the focusing procedure. In this work an effort has been carried out to try to focus the raw SAR complex data matrix without the knowledge of anyof the parameters needed in standard focusing procedures as Range Doppler (RD) algorithm, ω - K algorithm and Chirp Scaling (CS) algorithm. All the literature references regarding the algorithms needed to obtain a precise image from raw data use such parameters that refer both to the SAR system acquisition geometry and its radiometric specific parameters. In [12], authors introduced a preliminary work dealing with this problem and able to obtain, in the presence of a strong point scatterer in the observed scene, good quality images, if compared to the standard processing techniques. In this work the proposed technique is described and performances parameters are extracted to compare the proposed approach to RD.

Piezoelectric properties are of significant importance to medical ultrasound, actuators, sensor, and countless other device applications. The mechanism of piezoelectric properties can be deeply understood from structure evolutions. In this paper, we report a diagram of structure evolutions of the Pb(Zn1/3Nb2/3)0.91Ti0.09O3 (PZN-9PT) single crystal with excellent piezoelectric properties among the orthorhombic, tetragonal, and cubic phases with temperature increasing from room temperature to 220 C. Through fitting the temperature dependence XRD curves with Gauss and Lorenz functions, we obtained the evolutions of the content ratio of three kinds of phases (orthorhombic, tetragonal and cubic) and the lattice parameters of the PZN-9PT system with the changes of temperature. The XRD fitting results together with Raman and dielectric spectrums show that the phase transitions of PZN-9PT are a typical continuous evolution process, very similar to the phase transition of paraffin from solid to liquid. Additionally, resonance and anti-resonance spectrum show excellent piezoelectric properties of the crystals, which probably originate from the nano twin domains, as demonstrated by the TEM images. Of particular attention is that the thickness electromechanical coupling factor kt is up to 72%.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

The concept of smart morphing blades, which can control themselves to reduce or eliminate the need for active control systems, is a highly attractive solution in blade technology. In this paper an innovative passive control system based on Shape Memory Alloys (SMAs) is proposed. On the basis of previous thermal and shape characterization of a single morphing blade for a heavy-duty automotive cooling axial fan, this study deals with the numerical analysis of the aerodynamic loads acting on the fan. By coupling CFD and FEM approaches it is possible to analyze the actual blade shape resulting from both the aerodynamic and centrifugal loads. The numerical results indicate that the polymeric blade structure ensures proper resistance and enables shape variation due to the action of the SMA strips.

2017 was an excellent year in terms of new drugs (chemical entities and biologics) approved by the FDA, with a total of forty-six. In turn, one of the highlights was the number of peptides (six) included in this list. Here, the six peptides are analysed in terms of chemical structure, synthetic strategy used for their production, source, biological target, and mode of action.

The LiCl and LiNO₃ water solutions in the presence of small amounts of 3-helium have been investigated by means of multinuclear resonance spectroscopy. The resulting concentration dependences of the ³He, ^6,7Li⁺, ¹⁴NO₃^¯ and ³⁵Cl^¯ resonance radiofrequencies are reported in the infinite limit. This data along with new theoretical corrections of shielding lithium ions was analyzed by a known NMR relationship method. Consequently, the nuclear magnetic moments of ⁶Li and ⁷Li were established against that of the helium-3 dipole moment: μ(⁶Li)=+0.822046(5)μ_N and μ(⁷Li)=+3.256418(20)μ_N. The new results were shown to be very close to the previously obtained values of the (ABMR) atomic beam magnetic resonance method. This experiment proves that our helium method is well suited for establishing dipole moments from NMR measurements performed in water solutions. This technique is especially valuable when gaseous substances of the needed element are not available. All shielding constants of species present in water solutions are consistent with new nuclear magnetic moments and these taken as a reference. Both techniques – NMR and ABMR – give practically the same results providing that all shielding corrections are properly made.

The asymmetry in the dynamics of an electro-pneumatic actuating device consisting of an electro-pneumatic transducer and a single-action pneumatic actuator was unexpectedly found experimentally. This asymmetry manifests in response to large step excitations. The dynamic asymmetry effect is understood as a change in the shape of the response of an actuator depending on the direction of the actuators stem movement. The questions appears: How to explain this effect? Does this phenomenon reflect thermodynamic air processes? Is it connected with air-to-mechanical energy conversion? Together, six working hypotheses explaining this effect were formulated. The asymmetry was studied in detail using analytical and simulation modeling, as well as experimental research. In this respect, a nonlinear analytical model was developed, tuned, and later solved using simulations. The simulation model was verified based on the experiment data. In addition, the problem of the efficiency in the energy conversion of a single-action actuator was discussed and, in result, the maximum theoretical energy efficiency was determined. Subsequently, all six working hypotheses were verified. Finally, the hypothesis explaining asymmetry as an effect of the different thermodynamic air processes in both actuator’s stem travel directions was confirmed.

Zinc oxide (ZnO) nanostructures have been studied extensively in the past years due to the novel electronic, photonic, mechanical and electrochemical properties. Recently, more attention has been paid to assemble nanoscale building blocks into three dimensional (3D) complex hierarchical structures, which not only inherit the excellent properties of the single building blocks but also provide potential applications in the bottom-up fabrication of functional devices. This review article focuses on 3D ZnO hierarchical nanostructures, and summarizes major advances in the solution phase synthesis, applications in environment, and electrical/electrochemical devices. We present the principles and growth mechanisms of ZnO nanostructures via different solution methods, with an emphasis on rational control of the morphology and assembly. We then discuss the applications of 3D ZnO hierarchical nanostructures in photocatalysis, field emission, electrochemical sensor, and lithium ion batteries. Throughout the discussion, the relationship between the device performance and the microstructures of 3D ZnO hierarchical nanostructures will be highlighted. This review concludes with a personal perspective on the current challenges and future researches.

This paper is to summarize the involvement of the stress energy tensor in the study of fluid mechanics. In the first part we will see the implication that carries the stress energy tensor in the framework of general relativity. In the second part, we will study the stress energy tensor under the mechanics of perfect fluids, allowing us to lead third party in the case of Newtonian fluids, and in the last part we will see that it is possible to define space-time as a no-Newtonian fluids.

Energy is a fundamental ingredient in economic development and energy consumption is an index of prosperity and the standard of living. The consumption of energy has increased significantly in the last number of decades, as the standard of living has improved. Renewable energy is a sustainable and clean source of energy derived from nature. Renewable energy technology is one of the solutions, which produces energy by transforming natural resources into useful energy forms. When you do something for the first time in the world, you never attain a perfect product or solution from the start. In Central Greece Lamia city, we are the first to design and implement an off-grid energy system using hydrogen energy storage technology and phase change materials for a house residence. The action plan for energy efficiency, a series of directives and incentive mechanisms, mandatory energy certification of buildings, indicate the urgent need to reduce energy consumption in buildings, which results in a more comfortable living, long service life of buildings, which in turn preserves the environment.

The switched inertance hydraulic system (SIHS) is a novel high-bandwidth and energy-efficient digital device which can adjust or control flow and pressure by a means that does not rely on throttling the flow and dissipation of power. An SIHS can provide an efficient step-up or step-down of pressure or flow rate by using a digital control signal. In this article, analytical models of an SIHS in a four-port high-speed switching valve configuration are proposed, and the system dynamics and performance are investigated theoretically and experimentally. The flow responses, system characteristics and power consumption can be predicted effectively and accurately by using the proposed models, which were validated by comparing with experiments and with numerical simulation. The four-port configuration is compared with the three-port configuration, and it is concluded that the former one is less efficient for valves of the same size, but provides a bi-direction control capability. As bi-direction control is a common requirement, this constitutes an important contribution to the development of efficient digital hydraulics.

Most of the pore-scale imaging and simulations of non-Newtonian fluid are based on the simplifying geometry of network modeling and overlook the fluid rheology and heat transfer. In the present paper, we developed a non-isothermal and non-Newtonian numerical model of the flow properties at pore-scale by direct simulation of the 3D micro-CT images using a Finite Volume Method (FVM). The numerical model is based on the resolution of the momentum and energy conservation equations. Owing to an adaptive meshing technique and appropriate boundary conditions, rock permeability and mobility are accurately computed. A temperature and concentration-dependent power-law viscosity model in line with the experimental measurement of the fluid rheology is adopted. The model is first applied at isothermal condition to 2 benchmark samples, namely Fontainebleau sandstone and Grosmont carbonate, and is found to be in good agreement with the Lattice Boltzmann method (LBM). Finally, at non-isothermal conditions, an effective mobility is introduced that enables to perform a numerical sensitivity study to fluid rheology, heat transfer, and operating conditions. While the mobility seems to evolve linearly with polymer concentration, the effect of the temperature seems negligible by comparison. However, a sharp contrast is found between carbonate and sandstone under the effect of a constant temperature gradient. Besides concerning the flow index and consistency factor, a good master curve is derived when normalizing the mobility for both the carbonate and the sandstone.

In this paper we develop from first principles a unique law pertaining to the flow of fluids through closed conduits. This law, which we call “Quinn’s Law”, may be described as follows: When fluids are forced to flow through closed conduits under the driving force of a pressure gradient, there is a linear relationship between the normalized dimensionless pressure gradient, P_Q, and the normalized dimensionless fluid current, C_Q. The relationship is expressed mathematically as: P_Q = k₁ +k₂C_Q. This linear relationship remains the same whether the conduit is filled with or devoid of solid obstacles. The law differentiates, however, between a packed and an empty conduit by virtue of the tortuosity of the fluid path, which is seamlessly accommodated within the normalization framework of the law itself. When movement of the fluid is very close to being at rest, i.e., very slow, this relationship has the unique minimum constant value of k₁, and as the fluid acceleration increases, it varies with a slope of k₂ as a function of normalized fluid current. Quinn’s Law is validated herein by applying it to the data from published classical studies of measured permeability in both packed and empty conduits, as well as to the data generated by home grown experiments performed in the author’s own laboratory.

The feasible, reliable and selective multi-template molecularly imprinted polymers (MT-MIPs) based on SBA-15 (SBA-15@MT-MIPs) for the selective separation and determination of the trace level of ginsenoside Rb₁ (Rb₁), ginsenoside Rg₁ (Rg₁) and notoginsenoside R₁ (R₁) (Panax notoginseng saponins, PNS) from biological samples were developed. The polymers were constructed by SBA-15 as support, Rb₁, Rg₁, R₁ as multi-template, acrylamide (AM) as functional monomer and ethylene glycol dimethacrylate (EGDMA) as cross-linker. The new synthetic SBA-15@MT-MIPs were satisfactorily applied to solid-phase extraction (SPE) coupled with high performance liquid chromatography (HPLC) for the separation and determination of trace PNS in plasma samples. Under the optimized conditions, the limits of detection (LODs) and quantitation (LOQs) of the proposed method for Rb₁, Rg₁ and R₁ were in the range of 0.63-0.75 ng mL^-1 and 2.1-2.5 ng mL^-1, respectively. The recoveries of R₁, Rb₁ and Rg₁ were obtained between 93.4% and 104.3% with relative standard deviations (RSDs) in the range of 3.3-4.2%. All results show that the obtained SBA-15@MT-MIPs could be a promising prospect for the practical application in the selective separation and enrichment of trace PNS in the biological samples.

Two novel inorganic–organic hybrid supramolecular assemblies, namely, (4-HNA)(18-crown-6)(HSO₄) (1) and (4-HNA)₂(18-crown-6)₂(PF₆)₂(CH₃OH) (2) (4-HNA = 4-nitroanilinium), were synthesized and characterized by infrared spectroscopy, single X-ray diffraction, differential scanning calorimetry (DSC), and temperature-dependent dielectric measurements. The two compounds underwent reversible phase transitions at about 255 K and 265 K, respectively. These phase transitions were revealed and confirmed by the thermal anomalies in DSC measurements and abrupt dielectric anomalies during heating. The phase transition may have originated from the [(4-HNA)(18-crown-6)]⁺ supramolecular cation. The inorganic anions tuned the crystal packings and thus influenced the phase-transition points and types. The variable-temperature X-ray diffraction data for crystal 1 revealed the occurrence of a phase transition in the high-temperature phase with the space group of P2₁/c and in the low-temperature phase with the space group of P2₁/n. Crystal 2 exhibited the same space group P2₁/c at different temperatures. The results indicated that crystals 1 and 2 both underwent an iso-structural phase transition.

Viruses have established symbiotic relationships with almost every other living organism on Earth and at all levels of biological organisation, from other viruses up to entire ecosystems. In most cases, peacefully coexisting with their hosts, but in most relevant cases, parasitising them and inducing diseases. Viruses are playing an essential role in shaping the eco-evolutionary dynamics of their hosts, and have been also involved in some of the major evolutionary innovations either by working as vectors of genetic information or by being themselves coopted by the host into their genomes. Viruses can be studied at different levels of biological organisation, from the molecular mechanisms of genome replication, gene expression and encapsidation, to global pandemics. All these levels are different and yet connected through the presence of threshold conditions allowing for the formation of a capsid, the loss of genetic information or epidemic spreading. These thresholds, as it occurs with temperatures separating phases in a liquid, define sharp qualitative types of behaviour. These {\em phase transitions} are very well known in Physics. They have been studied by means of simple, but powerful models able to capture their essential properties, allowing to understand them. Can the physics of phase transitions be an inspiration for our understanding of viral dynamics at different scales? Here we review well-known examples of transition phenomena in virology and their simplest mathematical modelling approaches. We suggest that the advantages of abstract, simplified pictures used in Physics are also the key to properly understand the origins and evolution of complexity in viruses. By means of several examples, we explore this multilevel landscape and how minimal models provide deep insights into a diverse array of problems. The relevance of these transitions in connecting dynamical patterns across levels and their evolutionary and clinical implications are outlined.

Dermal interstitial fluid (ISF) is a novel source of biomarkers that can be considered as an alternative to blood sampling for disease diagnosis and treatment. Nevertheless, in vivo extraction and analysis of ISF are challenging. On the other hand, microneedle (MN) technology can address most of the challenges associated with dermal ISF extraction and is well-suited for long-term, continuous ISF monitoring as well as in situ detection. In this review, we first briefly summarise the different dermal ISF collection methods and compare them with MN methods. Next, we elaborate on the design considerations and biocompatibility of MNs. Subsequently, the fabrication technologies of various MNs used for dermal ISF extraction, including solid MNs, hollow MNs, porous MNs and hydrogel MNs, are thoroughly explained. In addition, different sensing mechanisms of ISF detection will be discussed in detail. Subsequently, we identify the challenges and propose the possible solutions associated with ISF extraction. A detailed investigation is provided for the transport and sampling mechanism of ISF in vivo. Also, the current in vitro skin model integrated with the MN arrays will be discussed. Finally, future directions to develop a point-of-care (POC) device to sample ISF are proposed.

This paper reports 2 × 4 hybrid Mach-zehnder interferometer (MZI) - multi-mode interferometers (MMI) based compact thermo-optical switch consisting of slab waveguides on silicon-on-insulator, SOI, platform. The device consists of two identical MMIs, each of 6 μm wide and 140 μm long connected with two phase shifters MMIs each with 2 μm wide and 8 μm long and linear tappers each 4 μm long, connected at both ends of the MMIs to minimize the power coupling loss. The loss for linear taper is found to be below 0.02dB. The footprint of the whole device is six 6 μm × 324 μm. This structure is based on unique multimode region shape, which leads optical switch to have less coupling loss and reduced cross-talk. The average thermo-optical switching power consumption is 1.4 mW, the excess losses are 0.8 dB, and the imbalances are 0.1 dB. Aluminum is used as a heating pad, and a trench is created around this pad to prevent from spreading of heat and reduce power loss almost by a factor of 2 to the adjacent phase shifter. Our new heating method has advantages of compact size and ease of fabrication with the current CMOS technology.

Concerning fan systems with an air pipe connecting air intake and a closed outlet, aerodynamic noise cannot be directly transmitted from the fan inlet and outlet to the outside. At this moment, the volute vibrational radiation noise induced casing surface vibration is the major noise component. The main factors affecting the fan vibrational noise are analyzed through theoretical derivation, then a vibrational noise optimization control method for the volute casing is proposed that considered the influence of vibro-acoustic coupling, taking the panel thickness of the volute (front-panel thickness [FT], side-panel thickness [ST], and back-panel thickness [BT]) as design variables, and the acoustical power of the volute surface and the total mass of the volute as the optimal target function. The optimization method is mainly divided into three main parts: the first was based on the simulation of unsteady flow of the fan to obtain the vibrational noise source; the second, using the design of experimental (DOE) method and the proposed numerical simulation of fluid-structure-acoustic coupling method to obtain the designing space, then the radical-based function (RBF) method is used to construct the approximate surrogate model instead of the simulation model previously mentioned, which was used to provide the basic mathematical model for the optimization of the next part; the third part, implementing the low vibrational noise optimization for the fan volute, applied the single-target (taking volute radiated acoustical power as the target function) and the multi-target (taking the volute radiated acoustical power and volute total mass as the target function) methods. In addition, the fan aerodynamic performance, volute casing surface fluctuations, and vibration response were validated by experiments, showing good agreement. It is of utmost importance that the dynamic pressure measurements and vibrational tests on the volute casing verify the accuracy of the numerical calculation. The optimization results showed that the vibrational noise optimization method proposed in this study can effectively reduce the vibration noise of the fan, obtaining a maximum value of noise reduction of 7.3 dB. The optimization identified in this paper provides a significant reference for the design of a low-vibrational-noise volute.

Cancers remain the lead cause of disease-related, pediatric death in North America. The emerging field of complex systems has redefined cancer networks as a computational system with intractable algorithmic complexity. Herein, a tumor and its heterogeneous phenotypes are discussed as dynamical systems having multiple, strange attractors. Machine learning, network science and algorithmic information dynamics are discussed as current tools for cancer network reconstruction. Deep Learning architectures and computational fluid models are proposed for better forecasting gene expression patterns in cancer ecosystems. Cancer cell decision-making is investigated within the framework of complex systems and complexity theory.

Quantum Fisher Information (QFI) is a very useful concept for analyzing situations that require phase sensitivity. It become a popular topic especially in Quantum Metrology domain. In this work, we study the changes in quantum Fisher information (QFI) values for one relative arbitrary phased quantum system consisting of a superposition of N Qubits W and GHZ states. In a recent work [7], QFI values of this mentioned system for N qubits were studied. In this work, we extend this problem for the changes of QFI values in some noisy channels for the studied system. We show the changes in QFI depending on noise parameters. We report interesting results for different type of decoherence channels. We show the general case results for this problem.

Thermophysical characterization of three paraffin waxes (RT27, RT21 and RT35HC) is carried out in this study using DSC, TGA and transient plane source technics. Then, a numerical study of their melting in a rectangular enclosure is examined. The enthalpy-porosity approach is used to formulate this problem in order to understand the heat transfer mechanism during the melting process. The analysis of the solid-liquid interface shape, the temperature field shows that the conduction is the dominant heat transfer mode in the beginning of the melting process. It is followed by a transition regime and the natural convection becomes the dominant heat transfer mode. The effects of the Rayleigh number and the aspect ratio of the enclosure on the melting phenomenon are studied and it is found that the intensity of the natural convection increases as the Rayleigh number is higher and the aspect ratio is smaller. In the second part of the numerical study, a comparison of the performance of paraffins waxes during the melting process is conducted. Results reveals that from a kinetically RT21 is the most performant but in term of heat storage capacity, it was inferred that RT35HC is the most efficient PCM.

The current need to develop sustainable power sources has led to the development of ocean-based conversion systems. Wells turbine is a widely used converter in such systems which suffers from a lack of operational range and power production capacity under operational conditions. The profile named IFS which is concave in the post-mid-chord region, can produce significantly larger lift forces and show better separation behavior than the NACA profiles. In the present study, we tested this profile for the first time in a Wells turbine. The performance of six different blade designs with IFS and NACA profiles were evaluated and compared using a validated computational fluid dynamic model. Although the substitution of the NACA profile with the IFS profile in all cases increased the torque generated, the most efficient power generation and the largest efficient range were achieved in the design with varying thickness from the hub with a 0.15 thickness ratio reaching to the ratio of 0.2 at the tip. The operational span of this design with the IFS profile was 24.1% greater and the maximum torque generation was 71% higher than the case with the NACA profile. Therefore, the use of the IFS profile is suggested for further study and practical trials.

Filament wound composite pipes are frequently used in the field were transmission of high pressured chemical fluids, disposal of industrial wastes, oil and natural gas transmission takes place. In oil and gas industry, the pipelines transporting heavy crude oil are subjected to variable pressure waves causing fluctuating stress levels in the pipes. Computational Fluid Dynamics Analysis was performed using Ansys 15.0 Fluent software to study the effects of these pressure waves on some specified joints in the pipes. Depending on the type of heavy crude oil being used, the flow behavior indicated a considerable degree of stress levels in certain connecting joints, causing the joints to become weak over a prolonged period of use. In this research comparison of various pipe joints was done by using different material and the output result of the stress levels of the pipe joints were checked so that the life of the pipe joints can be optimized by the change of material.

Using coherent optical detection and digital signal processing, laser phase noise and equalization enhanced phase noise can be effectively mitigated using the feed-forward and feed-back carrier phase recovery approaches. In this paper, theoretical analyses of feed-back and feed-forward carrier phase recovery methods have been carried out in the long-haul high-speed n-level phase shift keying (n-PSK) optical fiber communication systems, involving a one-tap normalized least-mean-square (LMS) algorithm, a block-wise average algorithm, and a Viterbi-Viterbi algorithm. The analytical expressions for evaluating the estimated carrier phase and for predicting the bit-error-rate (BER) performance (such as the BER floors) have been presented and discussed in the n-PSK coherent optical transmission systems by considering both the laser phase noise and the equalization enhanced phase noise. The results indicate that the Viterbi-Viterbi carrier phase recovery algorithm outperforms the one-tap normalized LMS and the block-wise average algorithms for small phase noise variance (or effective phase noise variance), while the one-tap normalized LMS algorithm shows a better performance than the other two algorithms for large phase noise variance (or effective phase noise variance). In addition, the one-tap normalized LMS algorithm is more sensitive to the level of modulation formats.

Lp16-PSP from Lentinula edodes strain C91-3 has been reported previously in our laboratory to have selective cytotoxic activity against a panel of human cell lines. Herein, we have used several parameters in order to characterize the Lp16-PSP-induced cell death using HL-60 as model cancer. The results of phase contrast microscopy, nuclear examination, DNA fragmentation detection and flow cytometry revealed that high doses of Lp16-PSP resulted in the induction of apoptosis in HL-60 cells. The colorimetric assay showed the activation of caspase-8, -9 and -3 cascade highlighting the involvement of Fas/FasL-related pathway. Whereas, western blot revealed the cleavage of caspase-3, increased expression of Bax, the release of cytochrome c and decreased expression of Bcl-2 in a dose-dependent manner, suggesting the intrinsic pathway might be involved in Lp16-PSP-induced apoptosis either. Low doses of Lp16-PSP resulted in the anchorage-independent growth inhibition, induction of G1 phase arrest accompanied by the increased expression of p21WAF1/CIP1 along with the decreased expression of cyclin D, E, and cdk6. Our findings suggest that induction of apoptosis and p21WAF1/CIP1 mediated G1 arrest might be one of the mechanisms of the action of Lp16-PSP, however, further investigations on multiple leukemia cell lines and in vivo models are of ultimate need.

In this work modeling and analysis of an integrated opto-fluidic sensor, with a focus on achievement of single mode optical confinement and continuous flow of micro particles in the microfluidic channel for Lab-on-a Chip (LOC) sensing application is presented. This sensor consists of integrated optical waveguides, microfluidic channel among other integrated optical components. A continuous flow of micro particles in a narrow fluidic channel is achieved by maintaining the two sealed chambers at different temperatures and by maintaining a constant pressure of 1Pa at the centroid of narrow fluidic channel geometry. The analysis of silicon on insulator (SOI) integrated optical waveguide at an infrared wavelength of 1550nm for single mode sensing operation is presented. The optical loss is found to be 0.0005719dB/cm with an effective index of 2.2963. The model presented in this work can be effectively used to detect the nature of micro particles and continuous monitoring of pathological parameters for sensing applications.

Without protective and/or therapeutic agents the SARS-CoV-2 infection known as coronavirus disease 2019 (COVID-19) is quickly spreading worldwide. It has surprising transmissibility potential, since it could infect all ages, gender, and human sectors. It attacks respiratory, gastrointestinal, urinary, hepatic, and endovascular systems and can reach the peripheral nervous system (PNS) and central nervous system (CNS) through known and unknown mechanisms. The reports on the neurological manifestations and complications of the SARS-CoV-2 infection are increasing exponentially. Herein, we enumerate seven candidate routes, which the mature or immature SARS-CoV-2 components could use to reach the CNS and PNS, utilizing the within-body crosstalk between organs. The majority of SARS-CoV-2 infected patients suffer from some neurological manifestations (e.g., confusion, anosmia, and ageusia). It seems that although the mature virus did not reach the CNS or PNS of the majority of patients, its unassembled components and/or the accompanying immune-mediated responses may be responsible for the observed neurological symptoms. The viral particles and/or its components have been specifically documented in endothelial cells of lung, kidney, skin, and CNS. This means that the blood-endothelial-barrier may be considered as the main route for SARS-CoV-2 entry into the nervous system, with the barrier disruption being more logical than barrier permeability, as evidenced by postmortem analyses.

Due to poor ventilation conditions in the tunnel, if gas pipeline leaks, the consequence of the accident will be more serious. Therefore, before the emergency repair, gas in the tunnel needs to be excharged so as not to explode during the repair process. Therefore, it is necessary to study the ventilation of gas in the tunnel. Based on the computational fluid dynamics (CFD) theory and taking the Yanyingshan tunnel section of China-Myanmar pipeline as an example, this paper uses Fluent software to establish the leakage model of the gas pipeline and fan model in the tunnel and analyzes the influence of different fan locations and number of fans on gas concentration. It can be concluded that: (1) the use of press-in method makes it more efficient to discharge gas out of the tunnel. (2) In order to make ventilation efficient, the fan should be arranged in a higher position and needs to be at a distance from the top of the tunnel. (3) Parallel use of two fans has better ventilation effect than single fan.

This thesis completion works it out to deepen into diverse modeling techniques for Point Absorbers. A combined frequency-time domain model is conceived, designed and developed in Matlab with Fortran as a base, leading to obtain physical variables of primary importance, namely position, velocity and power to energy net balance relationships of absorption. Integration of different degrees of freedom with heave as main executable leads in turn to a single buoy motion focus. Acquisition of the needed hydrodynamic coefficients is provided through application of NEMOH \& BEMIO solvers due to the Boundary Element Methodology. Initially, this Wave-to-motion model is validated by comparison with previous experimental results for a floating cone cylinder shape (Buldra-FO3). A single, generic, vertical floating cylinder is contemplated then, that responds to the action of the passing regular waves excitation. Later, two equally sized vertical floating cylinders aligned with the incident wave direction are modeled for a variable distance between the bodies. For both unidirectional regular and irregular waves as an input in deep water, we approximate the convolutive radiation force function term through the Prony method. By changing the spatial disposition of the axisymmetric buoys, using for instance triangular or rectangular shaped arrays of three and four bodies respectively, the study delves into motion characteristics for regular waves. The results highlight efficient layouts for maximizing the energy production whilst providing important insights into their performance, revealing displacement amplification- and capture width-ratios, while deriving in possible interpretations of scenarios related to the the known park effect. These terms are encompassed by the novelty of a new conceptual Post-Processing methodology in the field, which leads to obtain an optimal distance for the separated bodies with effective energy absorption in a regular wave regime. In conclusion, this computational excursion envisions and proposes potential fields of study, which will surely enhance new connections and link this renewable energy form.

Despite the successes earned in cataloguing and finding the role of the most of molecular components in living matter, the “biochemical and molecular” perspective, popular in biology, medicine and genetics, is unable to give account for crucial topics as the faculty of living systems to “feel”, to “perceive” what a given stimulus implies (means, indeed) for their survival. Condensed matter physics too, if bounded to a local, short-range, and perturbative approach, fails dramatically. This is also due to the role commonly assigned to water – actually the main constituent of living matter – deemed for long time to be merely chemical (as “solvent” or a reactant/product). Nonetheless, today many evidences show how living matter can be right conceived as a super-structured coherent water-based matrix, suggesting that the characterization of bio(electro)chemical and physical processes undertaken at molecular level in living matter, would let us unable to answer a question like this: what allows an amoeba, moreover without any neurons, to “know” to get closer to a nutrient or escape away from a toxin? I propose that to pursue such a fundamental inquiry it’s necessary an essentially relational approach, that is: to consider the living being at its grounding as the outcome of a physical history of relationships where symmetry-breakings, dissipation and coherence yield the emergence of the living state of matter, conceivable only as a time-dependent open process, and not as a portraited “body”. The effective tools to build up such an approach may be retrieved in far-from-equilibrium thermodynamics (TD), symmetry-breakings and gauge-fields theory, science of complexity, within the framework of a Quantum Field Theory. Indeed, within a field-view of matter, and of water especially, as it has been developed by a Quantum Electrodynamic (QED) description of condensed matter, it’s possible to give account for a physical basis too such an epistemologically elusive, though crucial, feature of living systems (i.e.: perception and meaning). The emerging landscape allows some important meditations about adaptation, evolution, ecodynamics, and about different conceptions of complexity and “information” in living realm. Furthermore, some neuroscientific themes like consciousness, qualia and their links to artificial intelligence could be supplied with due insights.

This paper proposes the use of non-uniform extended surfaces installed externally to the tubes of the radiation section of fired heaters, in order to obtain a better heat flux distribution to the coils. To this end, the heat transfer mechanisms present in such equipment were studied through computational fluid dynamics (CFD), using simplified geometries that represent typical sizes of fired heaters. Also, a simplified model for the combustion was considered. Although this model oversimplifies the physics of the problem, it was able to give satisfactory results for the parameters being optimized, considering the main objective of this paper, that is to minimize the non-uniformity of heat flux in the tubes of the radiant section of fired heaters. It was possible to obtain optimized geometric parameters for different types of extended surfaces evaluated, coupling the results of these models with the Particle Swarm optimization method through the use of a response surface technique,. The results indicate a significant improvement in the uniformity of the heat flux distribution to the tubes through the use of the proposed extended surfaces. Thus, this solution reveals to be an interesting alternative to reduce the risks of fluid degradation and coking formation. Future studies must investigate the non-uniformity of the heat flux due to the presence of the flame and consider the interaction between the reactive flow and the participating medium. Nevertheless, this paper presents some results that justify the optimization of such extended surfaces taking into consideration thermal radiation.

Among all the processing technologies of heat-treatable aluminum alloys like 2219 aluminum alloy, using friction stir welding (FSW) as the joining technology and using electromagnetic forming (EMF) for plastic forming technology both have obvious advantages and successful applications. Therefore, there is a broad prospect for the compound technologies which can be used on the 2219 aluminum alloy to manufacture the large-scale thin-wall parts in the astronautic industry. The microstructure and mechanical properties of 2219 aluminum alloy under the process compounded of FSW, heat treatment, and EMF were investigated by means of tensile test, optical microscope (OM), and scanning electron microscope (SEM). The results show that the reduction of strength, which was caused during the FSW process, can be recovered effectively by the post-welding heat treatment composed of solid solution and aging, while the ductility was still reduced after heat treatment. Under the compound technology of FSW, heat treatment, and EMF, the forming limit of 2219 aluminum alloy decreased distinctly due to the poor ductility of the welding joint. A ribbon-pattern, which was formed due to the banded structure caused by FSW process, was found on the fracture surface of welded 2219 aluminum alloy after EMF treatment. During the EMF process, because of the effects of induced eddy current, a unique structure, which was manifested as a molted-surface appearance under the SEM observation, was formed as the material fractured.

The World Health Organisation declared Covid-19 as a pandemic on 11th March 2020. The main approach to tackle Covid-19 worldwide is to screen and provide supportive care to patients. For screening purpose RT-qPCR based test are used as an initial detections assay. The test is expensive, time consuming and not suitable for mass scale screening/ confirmation requirement. A recent advancement is development of Immunoassay procedures (liquid Phase tests or bed side 10-20minute strip test). In order to help and accelerate bringing life to normal after lock down, Pakistan is in dire need to develop and adopt the immunoassay procedures for mass scale screening and confirmation of COVID-19 infection. It is cheap and easy to perform without a lab requirement.

The aim of this study is to provide the scientists with a straightforward correlation that can be applied for predicting the Fanning friction factor and consequently the pressure drop during blood flow in small caliber vessels. Due to the small diameter of the conduit, the Reynolds numbers are low and thus the flow is laminar. The study has been conducted using CFD simulations validated with relevant experimental data acquired using an appropriate experimental set-up. The experiments concern pressure drop measurement during the flow of a blood analogue that follows the Casson model, i.e. an aqueous glycerol solution that contains a small amount of xanthan gum and exhibits similar behavior to blood, in a smooth, stainless steel microtube (L=5.6cm and D=400 μm). The interpretation of the resulting numerical data led to the proposal of a simplified model that incorporates the effect of the flow rate, the hematocrit value (35-55%) and the vessel diameter (300-1800 μm) and predicts with better than ±10% the Fanning friction factor and consequently the pressure drop during laminar blood flow in small caliber vessels.

With the increasingly stringent airworthiness standards, the noise generated during the rotorcraft flight is gradually attracting people’s attention. It widely operated helicopters at low altitudes because of their maneuverability. The way to reduce the noise caused by the complex airflow of the helicopter rotor system has progressively become a hot topic for researchers. Using a hybrid acoustic analysis method, this paper investigates the improvement of the noise and thrust of the helicopter’s tail rotor through the tail rotor structural parameters. For the basic model, the turbulence simulation is performed using an incompressible detached eddy simulation (DES) method, and the Lighthill acoustic analog equation is calculated using the finite element method (FEM). We verified the accuracy of the method through wind tunnel tests. We chose a series of structural parameters for sound simulation and fluid simulation calculations. The results indicate that the modified tail rotor noise reduced by 16.5 dBA and the total thrust increased by 19.9% from the prototype model. This work can enhance the duct tail rotor design to improve aerodynamic and aeroacoustic performance.

Starting with a hypothetical geostrophic zonal current in an unbounded ocean, the investigation points out the response of this simple system to a thermal forcing, applied to the free surface and consistent with the maintenance of the geostrophic balance. The main result is the formation of a meridional component of the current, according to the Sverdrup relation, such that the full velocity vector rotates clockwise for heating and anticlockwise for cooling to adjust eventually in the initial zonal direction for large depths.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

In this work, we focus on investigating electrothermal flow in a rotating electric field (ROT-ETF), with primary attention paid to the horizontal traveling-wave electrothermal (TWET) vortex induced at the center of the electric field. The frequency-dependent flow profiles in the microdevice are analyzed using different heat transfer models. Accordingly, we address in particular the importance of electrode cooling in ROT-ETF as metal electrodes of high thermal conductivity while substrate material of low heat dissipation capability are employed to develop such microfluidic chips. Under this circumstance, cooling of electrode array due to external natural convection on millimeter-scale electrode pads for external wire connection occurs and makes the internal temperature maxima shift from the electrode plane to a bit of distance right above the cross-shaped interelectrode gaps, giving rise to reversal of flow rotation from a typical repulsion-type to attraction-type induction vortex, which is in good accordance with our experimental observations of co-field TWET streaming at frequencies on the order of reciprocal charge relaxation time of the bulk fluid. These results point out a way to make a correct interpretation of out-of-phase electrothermal streaming behavior, which holds great potential for handing high-conductivity analytes in modern microfluidic systems.

Stagnation is the transient state of a solar thermal system under high solar irradiation where the useful solar gain is zero. Both flat-plate collectors with selective absorber coatings and vacuum-tube collectors exhibit stagnation temperatures far above the saturation temperature of the glycol-based heat carriers within the range of typical system pressures. Therefore, stagnation is always associated with vaporization and propagation of vapor into the pipes of the solar circuit. It is therefore essential to design the system in such a way that vapor never reaches components that cannot withstand high temperatures. In this article, a thermal-hydraulic model based on the integral form of a two-phase mixture model and a drift-flux correlation is presented. The model is applicable to solar thermal flat-plate collectors with meander-shaped absorber tubes and selective absorber coatings. Experimental data from stagnation experiments on two systems, which are identical except for the optical properties of the absorber coating, allowed comparison with simulations carried out under the same boundary conditions. The absorber of one system features a conventional highly selective coating, while the absorber of the other system features a thermochromic coating, which exhibits a significantly lower stagnation temperature. Comparison of simulation results and experimental data show good conformity. This model is implemented into an open-source software tool called “THD” for the thermal-hydraulic dimensioning of solar systems. The latest version of THD, updated by the results of this article, enables planners to achieve cost-optimal design of solar thermal systems and to ensure failsafe operation by predicting the steam range under the initial and boundary conditions of worst-case scenarios.

Using a nonclassical symmetry of nonlinear reaction-diffusion equations, some exact multi-dimensional time-dependent solutions are constructed for a fourth-order Allen-Cahn-Hilliard equation. This models a phase field that gives a phenomenological description of a two-phase system near the critical temperature. Solutions are given for the changing phase of a cylindrical or spherical inclusion, allowing for a 'mushy zone' with mixed state that is controlled by imposing a pure state at the boundary. The diffusion coefficients for transport of one phase through the mixture, depend on the phase field value, since the physical structure of the mixture depends on the relative proportions of the two phases. A source term promotes stability of both of the pure phases but this tendency may be controlled or even reversed through the boundary conditions.

In this paper an integrated methodology for the coupling between 1D- and 3D-CFD simulation codes is presented, which has been developed to support the design and calibration of new diesel engines. The aim of the proposed methodology is to couple 1D engine models, which may be available in the early-stage engine development phases, with 3D predictive combustion simulations, in order to obtain reliable estimates of engine performance and emissions for newly designed automotive diesel engines. The coupling procedure features simulations performed in 1D-CFD by means of GT-SUITE and in 3D-CFD by means of Converge, executed within a specifically designed calculation methodology. An assessment of the coupling procedure has been performed by comparing its results with experimental data acquired on an automotive Diesel engine, considering different working points including both part load and full load conditions. Different multiple injection schedules have been evaluated for part-load operation, including pre and post injections. The proposed methodology, featuring detailed 3D chemistry modeling, was proven to be capable to properly assess pollutant formation, specifically to estimate NOx concentrations. Soot formation trend was also well-matched for most of the explored working points. The proposed procedure can therefore be considered as a suitable methodology to support the design and calibration of new Diesel engines, thanks to its ability to provide reliable engine performance and emissions estimations from the early-stage of a new engine development.

The deep Cretaceous tight sandstone in Kuqa Depression of Tarim foreland basin is an ultra-low porosity and ultra-deep gas-bearing reservoir, which is characterized by small pores, fine throats, and poor connectivity. The wireline logging responses are so complex, and especially, it is difficult to identify fluid types from resistivity logs. Based on acoustic, density, and neutron logs response differences in gas and water layers, effective fluid sensitivity factors are constructed for gas layer identification. From conventional logs, acoustic-neutron porosity difference, density-neutron porosity difference, and triple-porosity ratio are all sensitive parameters to the gas layer. From the NMR logging response mechanism, the density and NMR porosity difference, and T2 geometric mean of the movable fluid are also two sensitive parameters to the gas layer. Based on these parameters, a series of fluid typing charts are constructed and their adaptabilities are analyzed and compared. By contrast, NMR log interpretation is better, and triple-porosity comprehensive method from conventional logs is also effective when NMR logging is not available. Finally, the comprehensive fluid typing strategy by combining some methods for ultra-low porosity tight sandstone is summarized and optimized. This study is another alternative for fluid identification using non-electrical logs.

Batch combustion in wood log stoves is a promising application for latent heat storage (LHS), due to the transient heat production with high peak effects. The current study aimed at designing a compact, passive and durable LHS system storing a substantial part of the heat release during batch combustion and effectively releasing the stored heat to the room for 6 to 10 hours after the last batch. The LHS system consists of a coaxial cylinder located at the top of the wood stove, replacing part of the regular stovepipe. Internal metallic fins were applied as heat transfer enhancement to homogenize the temperature distribution inside the PCM. The effect of radial fin lengths was numerically investigated through a parametric study using five different fin lengths within the PCM. Using 35-mm fins in the 70-mm PCM layer yielded the best trade-off for the application. This configuration enabled achieving a slow but close to complete melting of the PCM within a realistic combustion duration, while avoiding overheating the PCM above its degradation temperature. Thereafter, the discharge allowed releasing the stored latent heat for 6 hours. The exhaust gas inlet temperature proved to have a strong influence on the PCM thermal performance.

We apply principles of Gibbs phase plane chemistry to and across the entire ocean-atmospheric interface. Surface tension increments support a two dimensional, tangential pressure well known to determine rates of bulk gas, bubble, salt, spray and momentum transfer plus both sensible and latent heat fluxes. Hence it is worth asking whether tension mapping follows from current understanding of two dimensional composition. A history is provided dating back centuries and demonstrating that detrital organic macromolecules are central; subtle surfactant functional variation creates a microforcing field which dissipates turbulent energy at the sub-meter scale. Since we have just distributed major biopolymeric classes emitted as primary organic aerosol, further climate links can be established by considering full planar thermochemistry. Organic microlayer behaviors are reviewed with attention to confined, analog phase transitions among two dimensional “solid, liquid, (and) gaseous” states serving as elasticity indicators. We also discuss surfactant properties of general marine dissolved organic carbon, demonstrating that only proteins and lipids are capable of occupying significant local micro-area. The literature often suggests albumin and stearic acid as best proxies, and so we distribute their concentrations through multilevel global ecodynamic simulations. Consensus distributions are obtained in order to control adsorptive equilibria. Working from conservation of planar free energy, a parametric equation of state is devised relating excess coverage to the surface pressure-modulus. Constant settings for the proxy pair are drawn from laboratory study, and they successfully reproduce frequencies for surfactant solid-to-gas occurrence in ambient compression experiments. Functionally resolved organic measurements are rare and so we group them into super-ecological province tables showing that our bulk concentration estimates are reasonable. Outputs are then fed into a coverage-tension-elasticity code. Resulting contours traverse the critical range for piston velocity, bubble-spray and damping effects on either a regional or seasonal basis. There is also a possibility for widespread microlayer crystallization in polar seas. The concepts are a direct extension of our organic aerosol work, and the two approaches could be inserted into Earth System Models in tandem. Uncertainties in the logic are enumerated and include kinetic and thermochemical factors at multiple scales. But the problems are reducible through molecular modeling coupled to renewed laboratory and field study. Connections to marine colloids-gels, microlayer iron chelation, and linings of the ice channel network are discussed additionally.

Below T_CO=157 K the quasi-one-dimensional charge-transfer salt (TMTTF)_2SbF_6 undergoes a pronounced phase transition to a charge-ordered ground state. We have explored the non-linear and photoconductive behavior as a function of applied voltage, laser pulse energy and temperature. Besides a decay of the photoconductive signal in a double exponential fashion in the millisecond range, we discover current oscillations in the kHz range induced by the application of short laser pulses. While the resonance frequencies do not depend on voltage or laser intensity and vary only slightly with temperature, the amplitude changes linearly with the laser intensity and voltage. The findings are discussed and compared to comparable phenomena in other low-dimensional electron systems.

The calculation of the standard enthalpies of vaporization, sublimation and solvation of organic molecules is presented using a common computer algorithm on the basis of a group-additivity method. The same algorithm is also shown to enable the calculation of their entropy of fusion as well as the total phase-change entropy of liquid crystals. The present method is based on the complete break-down of the molecules into their constituting atoms and their immediate neighbourhood; the respective calculations of the contribution of the atomic groups by means of the Gauss-Seidel fitting method is based on experimental data collected from literature. The feasibility of the calculations for each of the mentioned descriptors was verified by means of a 10-fold cross-validation procedure proving the good to high quality of the predicted values for the three mentioned enthalpies and for the entropy of fusion, whereas the predictive quality for the total phase-change entropy of liquid crystals was poor. The goodness of fit (Q²) and the standard deviation (σ) of the cross-validation calculations for the five descriptors was as follows: 0.9641 and 4.56 kJ/mol (N=3386 test molecules) for the enthalpy of vaporization, 0.8657 and 11.39 kJ/mol (N=1791) for the enthalpy of sublimation, 0.9546 and 4.34 kJ/mol (N=373) for the enthalpy of solvation, 0.8727 and 17.93 J/mol/K (N=2637) for the entropy of fusion and 0.5804 and 32.79 J/mol/K (N=2643) for the total phase-change entropy of liquid crystals. The large discrepancy between the results of the two closely related entropies is discussed in detail. Molecules, for which both the standard enthalpies of vaporization and sublimation were calculable, enabled the estimation of their standard enthalpy of fusion by simple subtraction of the former from the latter enthalpy. For 990 of them the experimental enthalpy-of-fusion values are also known, allowing their comparison with predictions, yielding a correlation coefficient R² of 0.6066.

This year marks the 20th anniversary of the discovery that proteins with various cellular functions can be temporarily immobilized in the nucleolus, a process known as nucleolar sequestration. This review reflects on the progress made to understand the physiological roles of nucleolar sequestration and the mechanisms involved in protein immobilization. We discuss how nucleolar sequestration consists of a highly choreographed amyloidogenic liquid-to-solid phase transition that converts the nucleolus into Amyloid bodies (A-bodies). The study of solid condensates A-bodies will offer unique perspectives on cellular assembly of membrane-less compartments and provide alternative insights on pathological amyloidogenesis involved in neurological disorders.

The Munich ChronoType Questionnaire (MCTQ) has now been available for more than 15 years; its original publication has been cited 1,240 times (Google Scholar, May 2019); its online version, which was available until July 2017, has produced almost 300,000 entries from all over the world (MCTQ database). The MCTQ has gone through several versions, has been translated into 13 languages and has been validated against other more objective measures of daily timing in several independent studies. Besides being used as a method to correlate circadian features of human biology with other factors – ranging from health issues to geographical factors – the MCTQ gave rise to quantifying old wisdoms, like “teenagers are late” and has produced new concepts, like social jetlag. Some like the MCTQ’s simplicity and some view it critically; it is time to have a self-critical view on the MCTQ, to address some misunderstandings and give some definitions about MCTQ-derived chronotype and the concept of social jetlag.

This paper studied the nonlinear vibrations of top tensioned cantilevered pipes conveying pressurized steady two-phase flow under thermal loading. The coupled axial and transverse governing partial differential equations of motion of the system were derived based on Hamilton’s mechanics with the centreline assumed to be extensible. Multiple scale perturbation method was used to resolve the governing equations, which resulted to an analytical approach for assessing the natural frequency, mode shape and the nonlinear coupled axial and transverse steady state response of the pipe. The analytical assessment reveals that at some frequencies the system is uncoupled, while at some frequencies a 1:2 coupling exists between the axial and the transverse frequencies of the pipe. Nonlinear frequencies versus the amplitude displacement of the cantilever pipe conveying two-phase flow at super critical mixture velocity for the uncoupled scenario exhibit a nonlinear hardening behaviour, an increment in the void fractions of the two-phase flow resulted to a reduction in the pipe’s transverse vibration frequencies and the coupled amplitude of the system. However, increasing the temperature difference, pressure and the presence of top tension were observed to increase the pipe’s transverse vibration frequencies without a significant change in the coupled amplitude of the system.