Stress relaxation tests in cantilever bending were performed on the C7025 and C7035 alloys at 298K and 393K，respectively. The effect of stress-relief treatments on stress relaxation properties was investigated. The structural changes associated with the stress relaxation process were examined using transmission electron microscope. The stress relaxation curve fits well to empirical formula σ*=[Kˊln(t+α₀)+C]^-n for stress relaxation. The curves can be split into two stages. The stress relax quickly in the first stage, slows down in the second stage, and tends to be a certain limit value after a long time. The curve and microstructure reveals that the C7035 alloy has a lower rate of stress relaxation and a higher anti-stress relaxation capacity than the C7025. The first reason is that the movement of vacancies required by spinodal decomposition is inhibited, and the quantity of cobalt -containing vacancies decreases dramatically in the C7035 alloy. The other reason is that the precipitated phases became uniformly diffused in the C7035 alloy. The precipitate phase uniformly distributes in the grain boundaries and the matrix, during the relaxed condition, and thus the dislocations moving is blocked by the precipitates.

First, a brief overview is provided on humanoid robots, and also models for the dynamic behavior are discussed. As base for these models these two methods Denavit-Hartenberg and Newton-Euler are used. Main aim of this work is to investigate the stability of a biped robot developed from IHRT. There is currently the low base of robot - consisting of feet, legs, hips and upper part of robots body. This structure currently has ten degrees of freedom.

Objectives: To investigate the value of early lactate dynamic monitoring index in predicting prognosis of patients with sepsis and septic shock. Methods: We performed our test on 50 patients. Out of 50 patients, 28 are male, and 22 are female. Prospectively studied pediatric patients with septic shock were performed. Vital signs, Lactate clearance, were obtained at presentation 6 h, 12 h, 24 h over the first 48 h of hospitalization. The therapy received, outcome parameters of mortality and duration of hospitalization were recorded. Results: The statistical data and comparative analysis showed that an average of 16.88 days after admission, 5 patients have died, 17 patients are poorly prognosis leaves the hospital, and the remaining 28 are recovered and discharged. The primary outcome variable of mean 16 days hospitalization mortality rate was 10%. Poor prognosis 34% and fully recovery 56 % were observed. In this retrospective cohort study, a lactate level of more than 2.5mmol/L was the best threshold to predict 28-day mortality among severe sepsis and septic shock patients. In our research, we found mean LC 6 h 3.08mmol/L, and after 48 h mean it is 1.79mmol/L. Significant LC 6 h found, which is 8.08mmol/L in the death group patient where 48 h mmol/L shows significant high. Poor prognosis also presents a clinical increase of lactate level high in the LC 6 h analysis, which is 3.32mmol/L. Recovered patients showed a significant improvement after administering treatment depending on the patient organ involvement and good decrease of lactate reports achieved, which is 1.20mmol/L, where admission reports show it was 1.91mmol/L in LC 6 h. Mean Heart rate 94/51mmhg, pulse 119, temperature 39℃, respiratory rate 32.26, and urine output 456 ml recorded during our study. Death patient shows a remarkable detonation of those reports but has a significant clinical report with the recovered patients. Conclusion: The early lactate dynamic monitoring index has a high value in predicting sepsis and septic shock patients' prognosis, thus worth popularizing.

Leishmaniasis is a group of neglected infectious, non-contagious diseases caused by parasites of the Leishmania genus which affects millions of people worldwide. The drugs available for its treatment, especially in cases of visceral leishmaniasis, are old, outdated, have serious side effects and in many cases are ineffective due to the emergence of resistant strains. In this context, the search for new candidates for more effective and safer drugs which can become new therapeutic alternatives is a constant need. In this work, 10 new chalcones were synthesized in high yields through Claisen-Schmidt condensation and were evaluated in vitro against Leishmania infantum promastigotes and amastigotes. CP04 and CP06 compounds were the most promising, respectively showing IC50 values = 13.64 ± 0.25 and 11.19 ± 0.22 against promastigotes, and IC50 = 18.92 ± 0.05 and 22.42 ± 0.05 against amastigotes. The compounds did not show cytotoxicity in erythrocytes, showing selectivity indexes greater than 74 and 90. Molecular docking studies carried out under the sterol 14-alpha demethylase (CYP-51) (PDB: 3L4D) and trypanothione reductase (PDB: 5EBK) enzymes from L. infantum evidenced the great affinity of the CP04 molecule for these targets, showing Moldock score values of -94.0758 and -50.5692 KJ/mol-1, with these values being much lower than the co-crystallized ligand energies. Molecular dynamics simulations demonstrated great stability of CP04 in its targets, thus indicating a real interaction possibility. Our findings confirm the potential that chalcones have as candidates for anti-leishmania drugs, and suggest that the CP04 compound may become a promising drug candidate to design and develop novel chalcone-based analogs for leishmaniosis therapy.

One of the central criteria for free will is “Could I have done otherwise?” But because of a temporal asymmetry in human choice, the question makes no sense. The question is backward-looking, while human choices are forward-looking. At the time when any choice is actually made, there is as of yet no action to do otherwise. Expectation is the only thing to contradict (do other than). So the ability to do something not expected by the ultimate expecter, Laplace’s demon, is a better criterion for free will. If human action is fundamentally unpredictable, then we have free will. Scientists have studied a form of fundamental unpredictability, known as undecidability. The features that make a system capable of undecidable dynamics have been identified: program-data duality; potential to access an infinite computational medium; and the ability to implement negation. Humans have all three of these features, so we very likely are fundamentally unpredictable, so we have free will.

With the increasingly stringent airworthiness standards, the noise generated during the rotorcraft flight is gradually attracting people’s attention. It widely operated helicopters at low altitudes because of their maneuverability. The way to reduce the noise caused by the complex airflow of the helicopter rotor system has progressively become a hot topic for researchers. Using a hybrid acoustic analysis method, this paper investigates the improvement of the noise and thrust of the helicopter’s tail rotor through the tail rotor structural parameters. For the basic model, the turbulence simulation is performed using an incompressible detached eddy simulation (DES) method, and the Lighthill acoustic analog equation is calculated using the finite element method (FEM). We verified the accuracy of the method through wind tunnel tests. We chose a series of structural parameters for sound simulation and fluid simulation calculations. The results indicate that the modified tail rotor noise reduced by 16.5 dBA and the total thrust increased by 19.9% from the prototype model. This work can enhance the duct tail rotor design to improve aerodynamic and aeroacoustic performance.

Oleanolic acid (OA) being the ubiquitous compound in the plant kingdom is studied for both the neuroprotective and neurotoxic properties. The mechanism of acetylcholinesterase (AChE) inhibitory potential of OA is investigated using the molecular dynamic simulations (MD) and docking as well as membrane-like and in vitro tests. There are also applied SH-SY5Y human neuroblastoma cells as well as in vivo on the zebrafish tests. The inhibitory potential towards the AChE enzyme is examined using the TLC-bioautography assay (the IC50 value is 9.22 μM). The CH- interactions between the central fragment of the ligand molecule and the aromatic cluster created by the His440, Phe288, Phe290, Phe330, Phe331, Tyr121, Tyr334, Trp84 and Trp279 side chains are observed. The in vitro tests carried out on the SH-SY5Y cells indicates that the viability rate is reduced to 71.5%, 61%, and 43% at the concentrations of 100 µg/mL, 300 µg/mL, and 1000 µg/mL, respectively after 48 hours of incubation whereas cytotoxicity against the tested cell line with the IC50 value is 714.32 ± 32.40 µg/mL. The in vivo tests on the zebrafish prove that there is no difference between the control and experimental groups as regards the mortality rate and morphology (P>0.05).

Here, we present a series of novel block copolymers (BCP) from bio-derived monomers, poly(lactic acid)-block-poly(2,5-furandimethylene succinate) (PLA-b-PFS), in which the furan groups from PFS block can be crosslinked with bis(maleimido) triethylene glycol (M2) through a Diels-Alder reaction. This dynamic crosslinking reaction leads to a network structure for enhancing the mechanical properties compared to their linear BCP analogous. Decreasing the crosslinking density leads to a decrease of glass transition temperature of BCPs and a transition from glassy to rubbery-like behavior at room temperature. This allows a wide tunablity of both elastic moduli and yields of the materials. For the lowest crosslinking density. the material exhibits an over 50% self-healing efficiency at room temperature after five days, attributed to the low Tg (15.2 C) from the introduction of PFS block, allowing sufficient chain mobility for structure re-organization. Moreover, with the appropriate selection of crosslinking density (PLA-b-PFS/M2 (6/1)), it also shows an excellent shape memory property with a high recovery rate of 96.3% and a fixity rate of 97.3%. The permanent shape can be rewriteable due to the reversibility of Diels-Alder reaction. With these advanced functionalities and ease in large-scale fabrication, the PLA-b-PFS/M2 shows great promises for self-healing coatings or films with shape memory properties in a wide variety of applications such as packaging materials

Emergence of multi drug resistant (MDR) and extensively drug resistant (XDR) Mycobacterium tuberculosis poses a serious threat to TB control as the available treatment options are less effective in these cases. Therefore, new strategies are required for identification of new drugs and drug targets. The M. tuberculosis dihydrodipicolinate synthase is a putative drug target with no potent inhibitor. Here in this study, we have used a comprehensive computational approach to identify small molecule inhibitors and validated them in vitro. As similar structures tend to have similar functions, therefore 3 approaches, namely, (a) known inhibitor-based approach, (b) substrate analogues, (c) product analogues were used for compound screening from various chemical libraries. The fourth approach we have taken is fragment library screening.In vitro studies revealed that β-hydroxypyruvic acid tartronic acid are inhibitors of Mtb-rDapA with maximum inhibition 48% and 51% at 500µM concentrations respectively. We have also observed that β-hydroxypyruvic acid is a time dependent inhibitor of Mtb-rDapA. Further, thermal shift assays showed that β-hydroxypyruvic acid interacts with Mtb-rDapA and the thermal stability of Mtb-rDapA shifted by 3˚C. Among the product analogues of Mtb-DapA, dipicolinic acid showed to bind to Mtb-rDapB shifting thermal stability of Mtb-rDapB by 0.5˚C in binding. Additionally, we have designed a new approach by combining substrate and product analogues to achieve better inhibitions. In vitro assays validated that this combination approach increased maximum inhibition up to 100%. We envision that these compounds would serve as potent leads for tuberculosis drug discovery.

China is not only short of fresh water resources per capita, but also faces a serious problem of water pollution in recent years, with 190 million people suffering from excessive levels of harmful substances in their drinking water. Such as arsenic poisoning and fluorosis and other endemic water diseases high incidence. As a series of water pollution prevention plan of action by the Chinese government announced that, this paper uses the modified Undesirable Dynamic Network model empirical analysis of China's 31 provincial administrative region economic growth, wastewater treatment, and water disease control efficiency between 2013 and 2017. The results show that the efficiency of water pollution disease in all four regions of China and the total efficiency in the three regions of east, west and central China all show a decreasing trend, and the efficiency scores and rankings of all provinces and cities within the region fluctuate greatly. The eastern region with the most developed economy has the best overall performance, with higher efficiency in Water consumption and Water disease control. However, the efficiency of wastewater treatment in northeast China is stable and better. Given the high level of economic development in China and the results of the above mentioned efficiency in water pollution and water diseases, improving the efficiency and quality of wastewater treatment in China is regarded as an important factor in achieving the strategic goal of green growth.

The dynamic factors in the environment violate the static environment assumption of the SLAM algorithm, leading to a decrease in the accuracy of camera positioning. In recent years, many studies have attempted to address dynamic objects by combining semantic constraints and geometric constraints, but issues such as poor real-time performance, the potential for mistakenly treating humans as rigid objects, and subpar performance in high-dynamic scenes still persist. This paper proposes a dynamic scene visual SLAM algorithm called Dynamic SLAM based on target tracking and multi-view geometry (TKG-SLAM), based on object detection, Kalman filters, and multi-view geometry. This algorithm takes into consideration both real-time performance and algorithm accuracy. It combines semantic constraints and multi-view geometry constraints, selectively running the algorithm in different scenarios, filtering and preserving static points for camera pose estimation. Experimental results demonstrate that, compared to current state-of-the-art dynamic SLAM methods, our approach achieves optimal performance in some scenarios and exhibits stronger real-time capabilities.

The proliferation of ransomware poses a significant threat to global cybersecurity. This study presents a comprehensive review of the methodologies employed in the detection and analysis of ransomware, emphasizing the dichotomy between static and dynamic analysis approaches. It introduces the historical context and the necessity for robust cybersecurity measures, followed by an outline of the methodological framework used to evaluate existing ransomware analysis techniques. The results detail the effectiveness and limitations of various analysis strategies, identifying key features and patterns that aid in the detection and classification of ransomware threats. The study concludes by summarizing the primary achievements, including the identification of gaps in current research and proposing future research directions aimed at enhancing ransomware detection and mitigation strategies. The synthesis provided in this survey offers a consolidated view of the state-of-the-art in ransomware threat analysis and serves as a resource for cybersecurity professionals and researchers.

Comparison between hydraulic and hydrologic computational methods is conducted in this study, regarding prismatic open channels under unsteady subcritical flow conditions. One-dimensional unsteady flow continuity and momentum equations are solved using explicit and implicit finite difference schemes for a symmetrical trapezoidal cross section, where the flow discharge and depth are the dependent variables. The results have been compared to those derived from Muskingum-Cunge hydraulic/hydrologic method as well as the commercial software HEC-RAS. The results from explicit and implicit code compare well to those from commercial software and hydraulic/hydrologic methods for long prismatic channels, thus directing the hydraulic engineer to quick preliminary design of prismatic open channels for unsteady flow with satisfactory accuracy.

Unsupported sleepers or void zones in ballasted tracks are one of the most recent and frequent track failures. The void failures have the property of intensive development that, without timely maintenance measures, can cause the appearance of cost-expensive local instabilities like subgrade damages. The reason of the intensive void development lies in the mechanics of the sleeper and ballast bed interaction. The particularity of the interaction is a dynamic impact that occur due to void closure. Additionally, void zones cause inhomogeneous ballast pressure distribution between the void zone and fully supported neighbour zones. The present paper is devoted studying the mechanism of the sleeper-ballast dynamic impact in the void zone. The results of experimental in-situ measurements of rail deflections showed the significant impact accelerations in the zone even for light-weight slow vehicles. A simple 3-beam numerical model of track and rolling stock interaction has shown the similar to the experimental measurements dynamic interaction. Moreover, the model shows that the sleeper accelerations are more than 3 times higher than the corresponding wheel accelerations and the impact point appear before the wheel enters the impact point. The analysis of ballast loadings shows the specific impact behaviour in combination with the quasistatic part that is different for void and neighbour zones, which are characterised with high ballast pre-stressed conditions. The analysis of void sizes influence demonstrate that the impact loadings, wheel and sleeper maximal accelerations appear at certain void depth after which the values decrease. The ballast quasistatic loading analysis indicates more than twice increase of the ballast loading in neighbour zones for long voids and almost full quasistatic unloading for short length voids. However, the used imitation model cannot explain the nature of the dynamic impact. The mechanism of the void impact is clearly explained by the analytic solution using a simple clamped beam. A simplified analytical expression of the void impact velocity shows that it is linearly related to the wheel speed and loading. The comparison to the numerically simulated impact velocities shows a good agreement and the existence of the void depth with the maximal impact. An estimation of the long-term influences for the cases of normal sleeper loading, high ballast pre-stress and quasistatic loading in the neighbour zones and high impact inside the void are performed.

: In this paper, we examine potential methods for autonomously tracking and landing multi-rotor unmanned aerial vehicles (UAVs), a complex yet essential problem. Autonomous tracking and landing control technology utilizes visual navigation, relying solely on vision and landmarks to track targets and achieve autonomous landing. This technology improves the UAV's environment perception and autonomous flight capabilities in GPS-free scenarios. In particular, we are researching tracking and landing as a cohesive unit, devising a switching plan for various UAV tracking and landing modes, and creating a flight controller that has an inner and outer loop structure based on relative position estimation. The inner and outer nested markers aid in the independent monitoring and touchdown of UAV. Optimal parameters are determined via optimized experiments on the measurements of the inner and outer markers. An indoor experimental platform for tracking and landing UAV was established. Tracking performance was verified by tracking three trajectories of unmanned ground vehicle (UGV) at varying speeds, and landing accuracy was confirmed through static and dynamic landing experiments. The experimental results show that the proposed scheme has good dynamic tracking and landing performance.

Human behaviour was tipped as the mainstay in the control of further SARS-CoV-2 (COVID-19) spread especially after the lifting of restrictions by many countries. Countries in which restrictions were lifted soon after the first wave, had subsequent waves of the COVID-19 infections and it remains to be seen whether there will be more waves. In this paper, we formulate a deterministic model for COVID-19 incorporating dynamic non-pharmaceutical interventions, dubbed social dynamics. The model steady states are determined and their stability analysed. Numerical simulations are carried out to determine the pack of various parameters that influence the social dynamics. In South Africa, the first wave was the only wave in which the only interventions rested solely on human behavior. The model is thus fitted to COVID-19 data on the first wave in South Africa. The results presented in this paper have implications on the trajectory of the pandemic in the presence of changing social processes.

This paper examines the dynamic dependence structure of crude oil and East Asian stock markets at multiple frequencies using wavelet and copulas. We also investigate risk management implications and diversification benefits of oil-stock portfolios by calculating and comparing risk and tail risk hedging performance. Our results provide strong evidence of time-varying dependence and asymmetric tail dependence between crude oil and East Asian stock markets at different frequencies. The level and fluctuation of their dependencies increase as time scale increases. Furthermore, we find the time-varying hedging benefits differ at investment horizons and reduced over the long run.

This paper presents a limited scope dynamic probabilistic risk assessment (D-PRA) on the survivability of commercial of the shelf (COTS) drones tasked with surveilling areas with varying radiation levels after a nuclear accident. The D-PRA is based on a discrete-dynamic event tree (D-DET) approach, which couples with the OpenEPL error propagation framework to model sequences leading to Loss of Mission (LOM) scenarios due to component failures in the drone’s navigation system. Radiation effects are simulated by calculating the total ionizing dose (TID) against the permissible limit per component, and errors are propagated within the electronic hardware and software blocks to quantify navigation system availability per radiation zone. The proposed methods are integrated into the traditional event tree/fault tree approach and the most vulnerable components are radiation-hardened (RAD-HARD) to the extent specified by a predefined mission success criterion. The results demonstrate the usefulness of the proposed approach in performing trade studies for incorporating COTS components into RAD-HARD drone designs.

This review describes the subjective experience of visual aura in migraine, outlines theoretical models of this phenomenon, and explores how these may be linked to neurochemical, electrophysiological and psychophysical differences in sensory processing that have been reported in migraine with aura. Reaction-diffusion models have been used to model the hallucinations thought to arise from cortical spreading depolarisation and depression in migraine aura. One aim of this review is to make the underlying principles of these models accessible to a general readership. Cortical spreading depolarisation and depression in these models depends on the balance of the diffusion rate between excitation and inhibition, and the occurrence of a large spike in activity to initiate spontaneous pattern formation. We review experimental evidence, including recordings of brain activity made during the aura and attack phase, self-reported triggers of migraine, and psychophysical studies of visual processing in migraine with aura, and how these might relate to mechanisms of excitability that make some people susceptible to aura. Increased cortical excitability, increased neural noise, and fluctuations in oscillatory activity across the migraine cycle are all factors likely to contribute to the occurrence of migraine aura. There remain many outstanding questions relating to the current limitations of both models and experimental evidence. Nevertheless, reaction-diffusion models, by providing an integrative theoretical framework, support the generation of testable experimental hypotheses to guide future research.

This investigation explores a novel path-planning and optimization strategy for multiple cooperative robotic agents, applied in a fully observable and dynamically changing obstacle field. Current dynamic path planning strategies employ static algorithms operating over incremental time-steps. We propose a cooperative multi-agent (CMA) based algorithm, based on natural flocking of animals, using vector operations. It is preferred over more common graph search algorithms like A* as it can be easily applied for dynamic environments. CMA algorithm executes obstacle avoidance using static potential fields around obstacles, that scale based on relative motion. Optimization strategies including interpolation and Bezier curves are applied to the algorithm. To validate effectiveness, CMA algorithm is compared with A* using static obstacles due to lack of equivalent algorithms for dynamic environments. CMA performed comparably to A* with difference ranging from -0.2% to 1.3%. CMA algorithm is applied experimentally to achieve comparable performance, with an error range of -0.5% to 5.2%. These errors are attributed to the limitations of the Kinect V1 sensor used for obstacle detection. The algorithm was finally implemented in a 3D simulated space, indicating that it is possible to apply with drones. This algorithm shows promise for application in warehouse and inventory automation, especially when the workspace is observable.

Porous metals possess low bulk density, large specific strength, high stiffness and special thermal, electromagnetic and acoustic conductivity, so that porous metals are widely used in filtration and separation, flame retardant explosion-proof, biomedical application, etc. Compared with its corresponding dense metal, the presence of porous structures also leads to different corrosive performances of porous metal. So, some researches have utilized weight loss method, electrochemical impedance to evaluate porous metals’ corrosion behavior; however, the influence of pore structure on metal corrosion is still controversial, and present methods used for analyses of porous metals’ corrosion are statistical averages of the corrosion behavior of the entire porous material, which cannot accurately reflect the corrosion behavior inside the pore structure. Herein, we prepare porous copper samples with 0, 24, 72, 96 pores using mechanical process, and employ scanning kelvin probe combined with electrochemical polarization curve and impedance spectroscopy to test the corrosion performance of the porous copper in static and dynamic NaCl solution. The relevant results indicate that in static solution, the corrosion resistance of samples gradually increases with the rise of the number of pores. By contrast, the sample with 24 pores exhibits more susceptible to corrosion than the sample without pore.

Environmental decentralization (ED), or the allocation of environmental protection affairs and responsibilities among various administrative authorities, affects the effectiveness of environmental regulation in promoting green total factor productivity (GTFP). Based on panel data of 30 Chinese provinces from 2001 to 2015, this paper employs dynamic panel models to test the effects of environmental regulations (environmental protection investment, ENV; pollutant discharge fees, PDF) on GTFP, with or without being influenced by ED. Without the impact of ED, GTFP is significantly inhibited by ENV while significantly promoted by PDF. Considering the impact of ED, with the strengthening of ED, the negative effects of ENV on GTFP is significant; contrarily, the positive effects of PDF on GTFP is significant; improving provincial ED adds negative effects of ENV, while reduces the positive effects of PDF; increasing prefectural ED reduces negative effects of ENV; expanding county-level ED adds the positive effects of PDF. Therefore, to boost GTFP growth, prefectural environmental protection authorities should have more autonomy in ENV, while the county-level should have more autonomy in PDF.

In recent years, both domestic and international research on quadruped robots has advanced towards high dynamics and agility, with a focus on high-speed locomotion as a representative motion in high-dynamic activities. Quadruped animals like cheetahs exhibit high-speed running capabilities, attributed to the indispensable role played by their flexible spines during the flight phase motion. This paper establishes dynamic models of quadruped robots with different degrees of spine flexibility, providing a parameterized description of the flight phase motion for both rigid trunks and flexible spine quadruped robots. By setting different initial values for the spine joint and calculating the flight phase results for both types of robots at various initial velocities, the study compares and analyzes the impact of a flexible spine on the flight phase motion of quadruped robots. Through comparative experiments, the research aims to validate the influence of a flexible spine during the flight phase motion, providing insights into how spine flexibility affects the flight phase motion of quadruped robots.

Neuromuscular disorders cause progressive muscular weakness, which limits upper extremity mobility and performance during activities of daily life. A dynamic arm support can improve mobility and quality of life. However, their use is often discontinued over time for unclear reasons. This study aimed to evaluate whether users of dynamic arm supports demonstrate and perceive quantifiable mobility benefits over a period of two months. Nine users of dynamic arm supports were included in this observational study. They had different neuromuscular disorders and collectively used four different arm supports. They were observed for three consecutive weeks during which they were equipped with a multi-sensor network of accelerometers to assess the actual use of the arm support and they were asked to provide self-reports on the perceived benefits of the devices. Benefits were experienced mainly during anti-gravity activities and the measured use did not change over time. The self-reports provided contextual information in domains such as participation to social life, in addition to the sensor system. However self-reports overestimated the actual use by up to three-fold compared to the accelerometer measures. A combination of objective and subjective methods is recommended for meaningful and quantifiable mobility benefits during activities of daily life.

Purpose: While resultant maximal voluntary contraction (MVC) is commonly used to assess muscular performance, the simultaneous activation of antagonist muscles could dramatically underestimate the strength of the agonist muscles. While quantification of antagonist torque has been performed in plantar- (PF) and dorsi-flexion (DF) joint in isometric conditions, it has yet to be determined in anisometric (concentric and eccentric) conditions. Methods: The experiment was performed in 9 participants through 2 sessions (reliability). The MVCs in DF and PF were measured in isometric, concentric and eccentric conditions (10°.s^-1). Electromyographic (EMG) activities from the soleus, gastrocnemius medialis and lateralis, and tibialis anterior muscles were simultaneously recorded. The EMG biofeedback method was used to quantify antagonist torque, where participants were asked to maintain a level of EMG activity, corresponding to antagonist EMG activity and related to the muscle contraction type, according to a visual EMG bio-feedback displayed on a screen. Results: Resultant torque significantly underestimated agonist torque in DF MVC (30-65%) and to a lesser extent in PF MVC (3%). Triceps surae antagonist torque was significantly modified with muscle contraction type, showing higher antagonist torque in isometric (29 Nm) than eccentric (23 Nm, p < 0.001) and concentric (14 Nm, p < 0.001) conditions and resulting in modification of the DF MVC torque-velocity shape. The difference between DF eccentric and concentric MVC was attenuated when considered agonist torque (12%) rather than resultant torque (45%). Conclusion: Estimation of the antagonist torque in isometric or anisometric condition brings new insights to assessment of muscular performance and could result in costly misinterpretation in strength training and/or rehabilitation programs.

Walking of humanoid robots is dependent on precise tracking of the center of gravity and foot trajectories. Trajectory tracking is achieved by mobilizing the robot joints to produce the correct trajectory. Errors are being occurred because of assumptions on tracking the center of gravity and the foot trajectories. In this study, a numerical algorithm has been developed that produces an exact and single kinematic solution in which the center of gravity and foot trajectories can be tracked with the desired precision. The effectiveness of the algorithm was examined with a dynamic simulation and compared with the method given in the literature The main highlight of this study, using the presented algorithm, the robot can walk even if the position of its center of gravity is lower than its hips, resulting tracking error was smaller than reported in the literature.

We have developed a self-consistent model for predicting velocity of 1/2[111] screw dislocation in binary iron--carbon alloys gliding by a high-temperature Peierls mechanism. The methodology of modelling includes: (i) Kinetic Monte-Carlo (kMC) simulation of carbon segregation in dislocation core and determination the total carbon occupancy of the core binding sites; (ii) Determination of kink-pair formation enthalpy of a screw dislocation in iron---carbon alloy; (iii) KMC simulation of carbon drag and determination of maximal dislocation velocity at which the atmosphere of carbon atoms can follow a moving screw dislocation; (iv) Self consistent calculation of average velocity of screw dislocation in binary iron--carbon alloys gliding by a high-temperature kink-pair mechanism under constant strain rate. We conduct a quantitative analysis of the conditions of stress and temperature at which screw dislocation glide in iron--carbon alloy is accomplished by a high-temperature kink-pair mechanism. We estimate the dislocation's velocity at which screw dislocation brakes away from the carbon cloud and thermally-activated smooth dislocation propagation is interrupted by sporadic bursts controlled by athermal dislocation activity.

Molecular dynamics simulations were carried out to investigate the atomic structure of a model Cu64Zr36 bulk metallic glass (BMG). It is found that the amount of icosahedral content of the system is significantly increased in a well relaxed structure. While we considered four connection types of vertex-, edge-, face-, and volume-sharing, the huge cluster in the relaxed samples mainly involve volume-type connection and exhibits a remarkable athermal plasticity that great stiffness and great yield strength compared to the as-quenched samples. In addition, the bond-angle distribution of annealed sample shows sharp peaks at specific bond angles which is an evidence of crystallized Laves-phase formed by icosahedral atoms, however the peaks are to be broaden after loading, which indicates decreasing amount of icosahedral content and their shape distortion. These results suggest that icosahedral content in a bulk metallic glasses plays a key role to determine the mechanical properties such as rigidity and maximum stress carrying capacity.

Piezoelectric cantilever harvesters have a large power output at their natural frequency, but in some applications the frequency of ambient vibrations is different from the harvester’s frequency and/or ambient vibrations are periodic with some harmonic components. To cope with these operating conditions harvesters with integrated trimming devices (ITDs) are proposed. Some prototypes are developed with the aid of an analytical model and tested with an impulsive method. Results show that a small trimming device can lower the main resonance frequency of a piezoelectric harvester of the same extent as a larger tip mass and moreover generates at high frequency a second resonance peak. A multi-physics numerical FE model is developed for predicting the generated power and for performing stress-strain analysis of harvesters with ITDs. The numerical model is validated on the basis of experimental results. Several configurations of ITDs are conceived and studied. Numerical results show that harvesters with ITDs are able to generate relevant power at two frequencies owing to the particular shape of the modes of vibration. The stress in the harvesters with ITDs is smaller than the stress in the harvester with a tip mass trimmed to the same frequency.

Biofuels and biochemicals play significant roles in the transition towards a fossil-free society. However, large-scale biorefineries are not yet cost-competitive with their fossil-fuel counterparts, and it is important to identify biorefinery concepts with high economic performance. For evaluating early-stage biorefinery concepts, one needs to consider not only the technical performance and process costs but also the economic performance of the full supply chain and the impacts on feedstock and product markets. This article presents and demonstrates a conceptual interdisciplinary framework that can constitute the basis for evaluations of the full supply-chain performance of biorefinery concepts. This framework considers the competition for biomass across sectors, assumes exogenous end-use product demand, and incorporates various geographical and technical constraints. The framework is demonstrated empirically through a case study of a sawmill-integrated biorefinery producing liquefied biomethane from forestry and forest industry residues. The case study results illustrate that acknowledging biomass market effects in the supply chain evaluation implies changes in both biomass prices and the allocation of biomass across sectors. The proposed framework should facilitate the identification of biorefinery concepts with a high economic performance which are robust to feedstock price changes caused by the increase in biomass demand.

This paper utilizes dynamic panel threshold technology to conduct a nonlinear test on the direct effect between environmental regulation and economic fluctuations and the effect of industrial structure upgrading by taking 35 industrial sectors in China from 2003 to 2016 . The research has found that there is an inverted "U" relationship between environmental regulation and economic fluctuations, with the enhancement of environmental regulations, the economic fluctuation increases first and then decreases. The cross-terms of environmental regulation and industrial structure rationalization or industrial structure upgrading are significantly negative, which indicates that the enhancement of environmental regulation is conducive to promoting industrial structure upgrading and reducing the economic fluctuations. While the rationalization factors of industrial structure and advanced industrial structure are significantly negative, indicating that both forms of industrial structure upgrading are conducive to reducing the economic fluctuations. Environmental regulation has technical innovation thresholds for industrial structure upgrading and economic fluctuations, but there are no human capital or FDI thresholds. In the rationalization model of industrial structure, there is a nonlinear "U" relationship between environmental regulation and economic fluctuations when the proportion of scientific research expenditure is more than 1.35%. With the enhancement of environmental regulation, the economic fluctuation reduces first and then increases, and the corresponding inflection point value is 2.398% of the environmental regulation level. At the same time, the environmental regulation can indirectly reduce economic fluctuations by pushing down the industrial structure upgrades. In the advanced model of industrial structure, there is a “U” relationship between environmental regulation and economic fluctuation when the proportion of scientific research expenditure is greater than 1.26%. With continuous enhancement of environmental regulation, the economic fluctuation reduces first and then increases. The corresponding inflection point value is 1.78% of the environmental regulation level, and environmental regulation can indirectly reduce economic fluctuations by promoting the industrial structure at the same time.

For better export marketing strategies (EMS), companies mobilize their internal resources, which are managerial commitment, firm experience, and product uniqueness. However, Small businesses with constrained resources cannot be well explained with this view. So, more research on how small business come up with EMS have been called for. To explain how resource-restricted firms which rely heavely on entrepreneur, this study adopted the concept of dynamic managerial capabilities (DMCs) and resource versatility to better explain small business exports. We analyzed small businesses in Mongolia with qualitative research methods, including interviews with entrepreneurs and support organizations, site visits, and group discussions. We suggest international dynamic marketing capabilities (IDMCs), which are entrepreneurial orientation, networking capability, and versatile dynamic capability for small business. Theoretical and managerial implications are discussed.

Photovoltaic shading devices (PVSDs) have the dual function of providing shade and generating electricity, which can reduce building energy consumption and improve indoor daylighting levels. This study adopts a parametric performance design method and establishes a one-click simulation process by using the Grasshopper platform and Ladybugtools. The research focuses on the effect of dynamic PVSDs on daylighting and energy consumption in an office building in Qingdao. Through simulation, the study calculates the monthly energy consumption and useful daylight illuminance (UDI) under different inclination angles and installation heights of PVSDs. And the optimal configuration of PVSDs for each month under three dynamic strategies (rotation, sliding, and hybrid) is determined. Additionally, different control strategies and fixed PVSDs are compared to clarify the impact of various control strategies on daylighting and energy consumption. The findings reveal that, compared to no shading, dynamic PVSDs in rotation strategy (with an installation height of 0 m), sliding strategy (with an inclination angle of 20°), and hybrid strategy can achieve energy savings of 32.13%, 47.22%, and 50.38%, respectively. They can increase the annual average UDI by 1.39%, 2.8%, and 3.1%, respectively.

Based on the recorded watershed characteristics, the future conditions on the basin system can be predicted using a different method. In this study, dynamic land-use change and its impacts on the streamflow for the Dabus watershed were predicted using ANN-CA based method. The model performance for accurate prediction of the future land-use change on the Dabus River watershed has been checked by validation of the simulated value with the actual value, hence the overall kappa value (k) = 0.83 for the simulated 2016-LULC validated with actual 2016-LULC. Then, 2026-LULC was predicted based on the 2004 and 2009-LULC. The streamflow for the case of 2004 and 2009-LULC has been simulated using the SWAT model. The value of NSE = 0.87 and 0.90 was attained during validation of simulated streamflow for 2004 and 2009-LULC data cases, respectively. The agreement of simulated value of streamflow with the observed data is indicated as R2 = 0.91 and 0.96 for 2004-LULC and 2009-LULC. The effects of the dynamic land-use change on streamflow for the predicted land use(2026-LULC) catchment were evaluated by T-test analysis. Hence, T-stat =0.04 and -0.002 in the case of simulated streamflow used 2004-LULC and 2009-LULC, respectively compared with simulated value using 2026-LULC.

Numerical simulations of standard situations in the transition region from gas kinetics to fluid dynamics at small Mach numbers indicate a clear dependence of the simulation results on the underlying kinetic model (here: nonlinear and linearized Boltzmann collision operator vs. BGK relaxation model). We develop an improved mathematical framework (trace theory) to explain these differences. In particular we reveal certain deficiencies for the classical BKG system as well as for the standard Navier Stokes approach.

The sudden pervasive of severe acute respiratory syndrome Covid-19 has been leading the universe into a prominent crisis. It has influenced each zone, for example, industrial area, horticultural zone, Public transportation, economic zone, and so on. So as to see how Covid-19 affected the globe, we conducted an investigation characterizing the effects of the pandemic over the world using Machine Learning (ML) method. Prediction is a typical data science exercise that helps the administration with function planning, objective setting, and anomaly detection. We propose an additive regression model with interpretable parameters that can be naturally balanced by experts with domain intuition about the time series. We focus on global data beginning from 22^nd January 2020, till 26^th April 2020 and performed dynamic map visualization of Covid-19 expansion globally by date wise and predicting the spread of virus on all countries and continents. The major advantages of this work include accurate analysis of country-wise as well as province/state-wise confirmed cases, recovered cases, deaths, prediction of pandemic viral attack and how far it is expanding globally.

The utilization of primary school buildings is multifaceted, primarily due to the high occupancy density, varying thermal preferences among occupants, diverse indoor activities (such as walking, sports, and conversation), and a constant flow of individuals entering and exiting the building. This results in frequent opening and closing of external windows and doors and fluctuations in internal heat gain. Consequently, frequent interactions between the indoor and outdoor microenvironments lead to energy losses. This study conducts a comprehensive literature review on building energy loss stemming from occupant behavior and the interactions between indoor and outdoor microenvironments. Furthermore, it proposes a dynamic real-time monitoring system based on a computer data capture and visualization platform foundation for building energy loss. The research methods include data crawling, data association rule mining, and data association analysis. The research findings yield a universally applicable and informative building energy-saving design theory based on extensive data analysis. Additionally, the system presents information on occupants' behavior and the microclimate data of indoor and outdoor environments on a computer screen, facilitating human-machine communication and enabling timely adjustments to design strategies for new buildings and operation and maintenance strategies for existing buildings.

In recent years, many algorithms based on end-to-end deep networks have been proposed to deal with the target detection problem of videos. However, the deep network models usually consume a lot of computing resources during the procedure of analysis of videos with complex dynamic backgrounds. In this paper, a new method of object detection based on information theory is presented. Firstly, each frame in a video is converted into an effective information map by using the Harris corner detection method. Secondly, the sensitive areas in the frame are extracted by using the context information and the effective information maps of the consecutive video frames. The sensitive areas in the video frame are the candidate areas where the target objects would be appeared at high probabilities. Thirdly, the information entropy features of each sensitive area are extracted to form the feature matrix, based on which, an SVM model is trained for selecting the target areas from the sensitive areas. Finally, the locations of the objects are detected based on the target areas in the video with a complex dynamic background. As a lightweight video detection framework, the method presented in this paper can save a lot of computing resources. Experimental results show that this method can achieve good results in the benchmark of CDnet 2014.

Digital twins are the foundation of autonomous off-road vehicles. Dynamic reduction methods are one of several ways to develop digital twins for off-road vehicles. The article commences with a comprehensive overview of the most widely used dynamic reduction methods and then introduces performance metrics for assessing their efficacies in the context of digital twins. The paper additionally includes a detailed mathematical derivation of the state-space representation for reduced-order finite element models. The state-space representation of the reduced finite element models facilitates their export to problem-solving environments for dynamic analysis. The state-space models are eventually solved utilizing the built-in libraries of numerical solvers in textual and graphical programming platforms. In addition, the article identifies the set of solvers that best suit the simulation of virtual models for off-road vehicles. This article also includes an evaluation of the simulation results of digital models with modes ranging from 0 to 30 Hz. In addition, the article demonstrates the lower bound of the frequency range necessary and sufficient to be retained in off-road vehicle virtual models. Finally, the paper presents the simulation outcomes for digital models of commercial off-road vehicles with custom-built control, electrical, and control systems.

5G heterogeneous network overlaid by millimeter-wave (mmWave) access employs mmWave meshed backhauling as a promising cost-efficient backhaul architecture. Due to the nature of mobile traffic distribution in practice which is both time-variant and spatially non-uniform, dynamic construction of mmWave meshed backhaul is prerequisite to support the varying traffic distribution. Focusing on such scenario of outdoor dynamic crowd (ODC), this paper proposes a novel method to control mmWave meshed backhaul for efficient operation of mmWave overlay 5G HetNet through Software-Defined Network (SDN) technology. Our algorithm is featured by two functionalities, i.e., backhauling route multiplexing for overloaded mmWave small cell base stations (SC-BSs) and mmWave SC-BSs’ ON/OFF status switching for underloaded spot. In this paper, the effectiveness of the proposed meshed network is confirmed by both numerical analyses and experimental results. Simulations are conducted over a practical user distribution modeled from measured data in realistic environments. Numerical results show that the proposed algorithm can cope with the locally intensive traffic and reduce energy consumption. Furthermore, a WiGig (Wireless Gigabit Alliance certified) device based testbed is developed for Proof-of-Concept (PoC) and preliminary measurement results confirm the proposed dynamic formation of the meshed network’s efficiency.

Reconfigurable chiral metasurfaces with dynamic polarization manipulation capability are highly required in optical integrated systems. In this paper, we simultaneously realized giant and large-range switchable asymmetric transmission (AT) and circular conversion dichroism (CCD) in a vanadium dioxide (VO2) based metasurface. The AT and CCD of the insulator VO2 based metasurface reach 0.95 and 0.92, respectively. Utilizing the insulator-to-metallic phase transition of VO2, the AT and CCD could be continuously switched to near zero. Furthermore, the physics mechanism of the giant and switchable AT and CCD are analyzed. The proposed metasurface with large-range switchable AT and CCD is promising in the applications of biochemistry detection, chiral imaging and biosensing.

Because of the large number of parameters that interact in their function, determining dynamic regime parameters as well as the mode of function of amplifying stages is an extremely complex problem. This paper describes a LabVIEW application for studying the functioning of an ampli-fier in various connections. The user selects the generator's parameters, the type of connection and its parameters, as well as the electric charge characteristics. The application can determine both the stage characteristics and the Bode characteristics. The amplifier's stability zone, as well as its gain and phase, are determined based on these characteristics. An important advantage of this application is that the design of the amplifier stage can be made starting from some param-eters that the amplifier can establish, from which the values of components can be determined. In order to validate the simulation results using the LabVIEW application, a specialized program Multisim was used, as well as experimental measurements using the Electronics Explorer Board. Both Multisim and Electronics Explorer Board can determine Bode characteristics. In both simu-lations and experimental amplifiers, the same schemes with the same transistor was used. The application can be used for educational purposes as well as to design the amplifier's stage to achieve specific parameters.

Despite the successes earned in cataloguing and finding the role of the most of molecular components in living matter, the “biochemical and molecular” perspective, popular in biology, medicine and genetics, is unable to give account for crucial topics as the faculty of living systems to “feel”, to “perceive” what a given stimulus implies (means, indeed) for their survival. Condensed matter physics too, if bounded to a local, short-range, and perturbative approach, fails dramatically. This is also due to the role commonly assigned to water – actually the main constituent of living matter – deemed for long time to be merely chemical (as “solvent” or a reactant/product). Nonetheless, today many evidences show how living matter can be right conceived as a super-structured coherent water-based matrix, suggesting that the characterization of bio(electro)chemical and physical processes undertaken at molecular level in living matter, would let us unable to answer a question like this: what allows an amoeba, moreover without any neurons, to “know” to get closer to a nutrient or escape away from a toxin? I propose that to pursue such a fundamental inquiry it’s necessary an essentially relational approach, that is: to consider the living being at its grounding as the outcome of a physical history of relationships where symmetry-breakings, dissipation and coherence yield the emergence of the living state of matter, conceivable only as a time-dependent open process, and not as a portraited “body”. The effective tools to build up such an approach may be retrieved in far-from-equilibrium thermodynamics (TD), symmetry-breakings and gauge-fields theory, science of complexity, within the framework of a Quantum Field Theory. Indeed, within a field-view of matter, and of water especially, as it has been developed by a Quantum Electrodynamic (QED) description of condensed matter, it’s possible to give account for a physical basis too such an epistemologically elusive, though crucial, feature of living systems (i.e.: perception and meaning). The emerging landscape allows some important meditations about adaptation, evolution, ecodynamics, and about different conceptions of complexity and “information” in living realm. Furthermore, some neuroscientific themes like consciousness, qualia and their links to artificial intelligence could be supplied with due insights.

The damage evolution rules of coal under true triaxial combined static-dynamic loads are important to understand and reveal the mechanism of rockburst in coal mines. The numerical simulation was carried out using FLAC3D to explore the coupling effect of static and dynamic stress, especially the influence of dynamic load parameters. The results show that the increase of dynamic load amplitude not only makes the plastic zone grow exponentially and shorten the damage development time, but also decreases the residual strength of the coal sample, which leads to a much more violent of the dynamic failure. The stress wave can propagate more stable in the coal sample with the increase of dynamic load frequency and the development time of the plastic zone also show synchronous fluctuating features, and when the frequency is like the intrinsic frequency of the coal sample, the dynamic load has a significant stimulate effect. The static and dynamic loads have different damage effect to the coal sample under true triaxial stress path, the weight decreases in order of the minimum principal stress, the maximum principal, the amplitude of the dynamic load and at last the dynamic stress frequency by the entropy weight method analysis.

Visual inertial SLAM algorithms enable robots to autonomously explore and navigate in unknown scenes. However, most of the current SLAM systems highly rely on static environment assumptions, which fails in the exsitence of motional objects in the real environment. To improve the robustness and localization accuracy of SLAM systems in dynamic scenes, this paper proposes a visual-inertial SLAM framework that fuses semantic and geometric information, called DA-VINS. First, this paper presents a dynamic object classification method based on feature’s current motion state, which obtains temporary static features in the environment. Secondly, a features dynamics check module based on IMU prior and adjacent frame’s geometry constraint is designed to calculate dynamic factors. It also verifies the classification results of temporary static features. Finally, a dynamic adaptive bundle adjustment module based on the features’ dynamic factors is designed to adjust the weights of features in nonlinear optimization. We evaluated our method in public and our dataset. The results show that D-VINS is one of the most real-time, accurate, and robust systems in dynamic scenes.

Understanding and evaluating urban investment environment is essential for effectively improving the efficiency of resource allocation between cities and promoting overall development of the regional economy. This paper takes 15 node cities on maritime Silk Road covered by the “Belt and Road” as the research object, establishes a dynamic evaluation index system for investment environment, and uses projection pursuit cluster to analyze and evaluate the investment environment of the cities. It is found that the investment environment potential of a city is directly related to the level of social development, economic development, and the degree of opening to the outside world. It is recommended that node cities should seize the important opportunity of the construction of the Maritime Silk Road, introduce world-wide human, financial and material resources to promote regional resources allocation and flow, and continuously improve and upgrade the investment environment quality.

As a special class of “green” elastomers, thermoplastic vulcanizates (TPVs) have been widely used in industries due to the combination of the excellent resilience of conventional elastomers and the easy recyclability of thermoplastics. Here, the morphology evolution of TPVs based on polyamide 6/ethylene-propylene-diene rubber (PA6/EPDM) blends was investigated by varying the content of the curing agent, phenolic resin (PF). With the incorporation of 6 wt% PF, the gel content of the EPDM phase reaches a high value of 49.6wt% and a typical sea-island structure is formed with EPDM domain in a micro-nano size. The dynamic rheology behaviors of TPVs showed that with the curing degree of EPDM phase increasing, a denser network of EPDM particles is formed in PA6 matrix. Also, a lower crystal degree and crystal peak temperature are observed, indicating that the presence of a growth restriction of PA6 crystal plate induced by a thinner plastic layer between the adjacent EPDM particles. However, the crystal form of PA6 is not changed with the increasing curing degree of the EPDM phase. This study provides an effective strategy to realize a new kind of TPVs, which can be easily introduced into industrial applications.

The main focus of the in vitro toxicity assessment methods is on the viability of the cells, which is usually based on metabolism changes. Yet, when exposed to toxic substances, the cell triggers multiple signals in response. With this in mind, we have developed a promising cell-based toxicity method that observes various cell responses when exposed to toxic substances (either death, division or remaining viable). Based on the collective cell response, we observed and predicted the dynamics of the cell population to determine the toxicity of the toxicant. The method was tested with two different conformations: In the first conformation, we exposed a monoculture model of blood macrophages to UV light, hydrogen peroxide, nutrient deprivation, tetrabromobisphenol A, fatty acids and 5-fluorouracil. In the second, we exposed a coculture liver model consisting of hepatocytes, hepatic stellate cells, Kupffer cells and liver sinusoidal endothelial cells to rifampicin, ibuprofen and 5-fluorouracil. The method showed good accuracy compared to established toxicity assessment methods. In addition, this approach provided more representative information on the toxic effects of the compounds as it considers the different cellular responses induced by toxic agents.

In many countries, governments have implemented non-pharmaceutical techniques to limit COVID-19 transmission. Restricting human mobility is one of the most common interventions, including lockdown, travel restrictions, working from home, etc. However, due to the strong transmission ability of the virus variants, further rounds of interventions, including a strict lockdown, are not considered as effective as expected. The paper aims to understand how the lockdown policy and pandemics changed human mobility in the real scenario. Here we focus on understanding the mobility changes caused by compliance with restrictions and risk perceptions, using the mobility index from the Google report during three strict lockdown periods in Leeds, the largest city in the county of West Yorkshire, England from March 2020 to March 2021. The research proposed the time-varying z-scores and Principal Component Analysis (PCA) to simulate how local people dynamically process and perceive health risk based on multi-dimensional daily COVID-19 reports first. Further modelling highlights exponentially increasing policy non-compliance through the duration of lockdown, probably attributable to factors such as mental anxiety and economic pressures. Finally, the proposed nonlinear regression model examines the mobility changes caused by the population's dynamic risk perceptions and lockdown duration. The case study at Leeds fits data well and shows that the third lockdown policy took effect much slower than the first. At the same time, the negative impact of the epidemic on population mobility decayed 40% in the third lockdown period in contrast with the first lockdown. The risk perception estimation methods could reflect that the local population became increasingly accustomed to the COVID-19 situation, and local people rationally evaluated the risks of COVID in the third lockdown period. The results prove that simulated risk perceptions and policy decay could explain urban mobility behaviour during the mobility well during lockdown periods, which could be a reference for future decision-making processes.

In this contribution, a method based on a solid solution theory of clathrate hydrate for multiple cage occupancy, host lattice relaxation and guest-guest interactions has been presented to estimate hydrate formation conditions of binary and ternary gas mixtures. We have performed molecular modeling of structure, guest distribution, and hydrate formation conditions for the CO₂ + CH₄, and CO₂ + CH₄ + N₂ gas hydrates. In all considered systems with and without N₂, at high and medium content of CO₂ in the gas phase we have found that CO₂ is more favorable to occupy clathrate hydrate cavities than CH₄ or N₂. Addition of N₂ to the gas phase increases ratio concentration CO₂ in compressing with concentration CH₄ in clathrate hydrates and makes gas replacement more effective. The mole fractions of CO₂ in CO₂ + CH₄ + N₂ gas hydrate rapidly increases with the growth of its content in the gas phase. And the formation pressure of CO₂ + CH₄ + N₂ gas hydrate rises in comparison with the formation pressure of CO₂ + CH₄ gas hydrate. Obtained results agree with the known experimental data for simple CH₄, CO₂ gas hydrates and mixed CO₂ + CH₄ gas hydrate.

The introduction on Zinc oxide nanoparticles (ZnOn) in sunscreens solved the issue of poor spreadability of these formulations, which often left a white film on the skin. However, safety concerns have arisen regarding the topical application of ZnOn. Some studies employed commercial sunscreens to address the safety issues of the topical application of ZnOn; however, commercial formulations are often complex and contain a wide range of ingredients that could attenuate the potential damage caused by the ZnOn. Therefore, in this study we aimed to develop a simple stable formulation containing 20% of coated and uncoated ZnOn, characterize the formulations and the nanoparticles, and assess the skin penetration in Franz diffusion cell. The Feret's diameter for the uncoated and coated ZnOn was 137 nm and 134 nm, respectively. For the uncoated ZnOn the hydrodynamic size in water was 368 nm and for the coated ZnOn, the average hydrodynamic size in ethyl acetate was 135 nm. The incorporation of ZnOn led to formulations more consistent and easier to spread, as suggested by the lower work of shear and higher values of firmness, cohesiveness, consistency and index of viscosity compared with the vehicle. The stability assessment at 45ºC suggested that the formulations containing the ZnOn were stable for 30 days and the vehicle was stable for 90 days. The assessment off the skin penetration by reflectance confocal laser microscopy indicated that the formulations did not permeate into the deepest layers of the skin, but accumulated on the skin furrows, hair and hair follicle.

SMARCA4-deficient non-small cell lung cancer (NSCLC) is a more recently recognized subset of NSCLC. We describe the 18F-fluorodeoxyglucose (FDG) PET/CT findings in a rare case of SMARCA4-deficient NSCLC and response to therapy. A 45-year-old male patient with a history of heavy smoking (10 years) underwent an 18F-fluorodeoxyglucose (FDG) PET/CT dynamic (chest) + static (whole-body) scan for diagnosis and pre-treatment staging. 18F-FDG PET/CT showed an FDG-avid mass in the upper lobe of the left lung (SUVmax of 22.4) and FDG-avid lymph nodes (LN) in the left pulmonary hilar region (SUVmax of 5.7). In addition, there are multiple metastases throughout the body, including distant LNs, adrenal glands, bone, and brain. Pathological findings confirmed SMARCA-4 deficient NSCLC. After 4 cycles of chemotherapy and immune checkpoint inhibitors（ICI）, the patient underwent again an 18F-FDG PET/CT scan (including dynamic scan) for efficacy evaluation. We report cases that deepen the understanding of the 18F-FDG PET/CT presentation of SMARCA4-deficient NSCLC as well as dynamic imaging features and parametric characteristics.

This article addresses the generic dynamic decision problem of how to achieve sustained market growth by increasing two interdependent organizational resources needed (1) to increase and (2) to sustain demand. The speed and costs of increasing each resource are different. Failure to account for this difference has been reported to lead to policies that drive a quick increase of demand followed by decline. Three generic policies derived from the literature have been implemented in a system dynamics model. Simulation shows that all three policies can generate sustained exponential growth but differ in performance. These results suggest that even policies which risk generating overshoot and collapse can avoid it. This poses two questions for further research: (1) what is the reasoning of human decision-makers when choosing between these policies and (2) how can the important but easily overlooked features of such decision situations be made sufficiently salient to be accounted for?

The aim of this expository article is to present recent developments in the centuries-old discussion on the interrelations between several types of domination in graphs. However, the novelty even more prominent in the newly discovered simplified presentations of several older results. Domination can be seen as arising from real-world application and extracting classical results as first described by this article.The main part of this article, concerning a new domination and older one, is presented in a narrative that answers two classical questions: (i) To what extend must closing set be dominating? (ii) How strong is the assumption of domination of a closing set? In a addition, we give an overview of the results concerning domination. The problem asks how small can a subset of vertices be and contain no edges or, more generally how can small a subset of vertices be and contain other ones. Our work was as elegant as it was unexpected being a departure from the tried and true methods of this theory that had dominated the field for one fifth a century. This expository article covers all previous definitions. The inability of previous definitions in solving even one case of real-world problems due to the lack of simultaneous attentions to the worthy both of vertices and edges causing us to make the new one. The concept of domination in a variety of graphs models such as crisp, weighted and fuzzy, has been in a spotlight. We turn our attention to sets of vertices in a fuzzy graph that are so close to all vertices, in a variety of ways, and study minimum such sets and their cardinality. A natural way to introduce and motivate our subject is to view it as a real-world problem. In its most elementary form, we consider the problem of reducing waste of time in transport planning. Our goal here is to first describe the previous definitions and the results, and then to provide an overview of the flows ideas in their articles. The final outcome of this article is twofold: (i) Solving the problem of reducing waste of time in transport planning at static state; (ii) Solving and having a gentle discussions on problem of reducing waste of time in transport planning at dynamic state. Finally, we discuss the results concerning holding domination that are independent of fuzzy graphs. We close with a list of currently open problems related to this subject. Most of our exposition assumes only familiarity with basic linear algebra, polynomials, fuzzy graph theory and graph theory.

The present work highlights some of the dynamic couplings observed in a series of tests performed in a wave basin with a scaled-model of a FOWT with semi-submersible substructure. The model was moored by means of a conventional chain catenary system and an actively controlled fan was used for emulating the thrust loads during the tests. A set of wave tests comprising regular and irregular waves was done for different wave angles and wind velocities. The experimental records illustrate the main coupling effects involved and how they affect the FOWT motions in waves, especially when the floater presents a non-negligible tilt angle.. In addition, an analysis of the frequency-domain dynamic model was made in order to evaluate its ability to capture these effects properly. The influence of different modes of fan response, floater trim angles (changeable with ballast compensation) and variations of the mooring stiffness with the offsets were investigated in the analysis. Results attest that significant changes in the FOWT responses may indeed arise from coupling effects, thus indicating that caution must be taken when simplifying the hydrodynamic frequency-domain models often used as a basis for the simulation of FOWTs in waves and in in optimization procedures for the design of the floater and mooring lines.

Three-point shooting plays an important role in determining the outcome of the basketball games, and could be relevant for player selection. However, there has been little research into the relationship between basketball players' physical capacities, metabolic capacities and three-point shooting accuracy, particularly among female players. The aim of this study was to examine the relationship between physical capacities, metabolic capacities and dynamic three-point shooting accuracy in female professional basketball players. Twelve female professional basketball players from the Women’s Chinese Basketball Association (WCBA) league (age: 19.04±1.31 years, height: 181.33±4.90cm, playing experience: 7.83±1.7 years) were recruited for this study. Pearson correlations and multiple linear regression analysis were run to assess the relationship between physical capacities, metabolic capacities and dynamic three-point shooting. Results showed that coordination, balance, core strength and relative average power were positively correlated with the three-point shooting accuracy (r>0.58, P<0.05), while no other variables showed significant correlations. The current study suggests that coaching staff should consider coordination, balance, core strength and anaerobic capacities when selecting players as well as in their training periodization if three-point shooting accuracy is considered relevant.

Injuries to the ligaments of the knee are extremely common among athletes who participate in high-risk sports, or any sport that requires frequent cutting motions, jumping, or contact. In order to determine the best way to heal these injuries, it is important to understand not just the pathology of the injury, but also the biomechanical factors that are affected, including stability and steadiness. While many studies have been done to examine the stability of healthy knees, there is little to no existing literature on stability of knees afflicted by injury. In order to surpass this obstacle, static steadiness and dynamic stability data was collected using the Lockhart Monitor phone application and Xsens accelerometers, respectively, both before and after completion of a course of physical therapy in a patient with a grade 2 medial collateral ligament (MCL) tear. These results were then used to determine the degree to which the prescribed physical therapy protocol was effective in healing the MCL, which can be useful for tweaking the individual protocol for future conservative treatment and management of the injury.

Contactless charging is evolving fast in many domains and applications such as the electrical vehicles (EV). The principle consists of transferring energy between two systems without having any electrical connection between them. This power transfer can be realized by emitting a magnetic field for Inductive Power Transfer (IPT). In the automotive domain, the application of contactless charging to supply power to the vehicle while driving is one of the solutions envisaged to solve the limited autonomy range of EV and reduced its cost but the system must comply with existing standards (e.g., allocated frequency range and radiated electromagnetic emissions), as summarized in this paper.

This experimental research presents an easier model for fitting experimental results that can be simulate the dynamical behaviour of a single degree freedom system, SDFS, subjected in a forced vibration in a shaking table. The fractional damping using a Kelvin-Voigt fractional derivative rheological model, KVFRdm, to represent a fractional oscillator and compare with the experimental model.

In this paper the possibility of harvesting energy from the vibrations of a plate is analyzed. The harvester takes the form of a cantilever dynamic vibration absorber equipped with a piezoelectric layer and tuned by means of a tip mass to the first mode of vibration of the plate. A mathematical model of the coupled system composed of the plate and the harvester is presented. The validity of the proposed harvester is proved by means of simulations carried out with the modal expansions approach. Simulation results highlighting the effect of harvester tuning and location are presented as well. Then the validity of the harvester is confirmed by experimental tests carried out both with a concentrated impulsive load and with a distributed pressure load. Simulations and experimental tests show that the cantilever piezoelectric dynamic vibration absorber generates open circuit voltage an order of magnitude larger than the one generated by the same piezoelectric layer when directly bonded to the plate surface.

Liquid and gas are distinct in their extent of dynamic atomic correlations; in gas atoms are almost uncorrelated whereas they are strongly correlated in liquid. This distinction applies also to electronic systems. Fermi liquids are actually gas-like, whereas strongly correlated electrons are liquid-like. Doped Mott insulators share characteristics with supercooled liquids. Such distinctions have important implications on superconductivity. We discuss the evolution of dynamic atomic correlations in liquid with temperature, and a possible effect of dynamic correlations on the high-temperature superconductivity in the cuprates.

Addressing sustainable mobility in urban areas has become a priority in today’s society, given the growing population and increasing vehicular flow in these areas. Intelligent Transportation Systems have emerged as innovative and effective technological solutions to address these challenges. Research in this area has become crucial, as it contributes not only to improve mobility in urban areas, but also to positively impact the quality of life of its inhabitants. To address this, a dynamic clustering methodology for vehicular trajectory data is proposed which can provide an accurate representation of the traffic state. Data was collected for the city of San Francisco, a dynamic clustering algorithm was applied and then an indicator was applied to identify areas with traffic congestion. Several experiments were also conducted with different parameterizations of the forgetting factor of the clustering algorithm. The results showed in terms of precision that the dynamic clustering methodology achieved high match rates compared to the congestion indicator applied to static cells.

Semantic segmentation of remote sensing urban scene imagery is a pixel-wise prediction, which is applied to identify the land-cover or land-use category. However, semantic segmentation demands huge computation cost. In order to reduce the huge computation cost, a common method is to introduce transformer and CNN hybrid method to have a good trade-off between accuracy and computation cost. However, recent CNN-transformer hybrid methods often capture local-global context and cross-window interaction information simultaneously. Then they introduce the local-global context to fuse the local feature, which repeat fuse the local and global feature and result in the additional computation cost. And previous methods often ignore to filter the local and global feature. To fix the problem, we design a lightweight decoder-EDDformer, which is Efficient Global Value Transformer with Dynamic Gatefusion module. Efficient global value transformer only response for extracting global feature. Dynamic Gatefusion module filter the local and global semantic feature and fuse them to capture the local-global context in one time. Extensive experiments reveal that our method not only runs faster but also achieves higher accuracy compared with other state-of-the-art lightweight models.

Japanese encephalitis virus (JEV) causes acute viral encephalitis in humans and reproductive disorders in pigs. JEV emerged during the 1870s in Japan and since that time, JEV has been transmitted exclusively throughout Asia, according to known reporting and sequencing records. A recent JEV outbreak occurred in Australia which affected commercial piggeries across different temperate southern Australian states and caused confirmed infections in humans. A total of 47 human cases and seven deaths were reported. The recent evolving situation of JEV needs to be reported due to its continuous circulation in endemic regions and spread to non-endemics areas. Here, we reconstructed the phylogeny and population dynamics of JEV using recent JEV isolates for the future perception of disease spread. Phylogenetic analysis shows the most recent common ancestor occurred about 3120 years ago (YA) (95% Highest posterior density [HPD], 2680 to 3715). Our results of the Bayesian skyline plot (BSP) demonstrates that JEV demography lacks fluctuations for the last two decades, but it shows that JEV genetic diversity has increased during the last ten years. This indicates the potential JEV replication in the reservoir host, which is helping it to maintain its genetic diversity, and to continue its dispersal into non-endemic areas. The continuous spread in Asia and recent detection from Australia further support these findings. Therefore, an enhanced surveillance system is needed along with precautionary measures such as regular vaccination and mosquito control to avoid future JEV outbreaks.

Decision making is a complex process involving various parts of the brain which are active during different times. It is challenging to measure externally the exact instance when any given region becomes active during the decision-making process. Here we try to extract and visualize the dynamic functional brain activation information from the observed fMRI data. We propose the use of a regularized deconvolution model to simultaneously map various activation regions within the brain and track how different activation regions changes with time. Thus, providing both spatial and temporal brain activation information. The activation information can then be further analyzed as per need and requirements. The proposed technique was validated using simulated data and then applied to a simple decision-making task for identification of various brain regions involved in different stages of decision making. The visualization aspect of the algorithm allows us to actually see the flow of activation (and deactivation) in form of a motion picture. The dynamic estimate may aid in understanding the causality of activation between various brain regions in a better way.

In this work, the degassing process of corn seeds was experimentally and numerically analyzed by removing air or other gases from around the seeds, specifically from the seed coating, in a rough vacuum chamber. The two complementary variants are employed to understand and optimize this process to improve the quality and germination rate of the seeds. Several experiments were conducted with well-established durations and masses of corn seeds at different temperatures to observe and record the behavior of the system, facilitating the modeling of the degasification process in the vacuum compartment. Modeling the degasification operation in the vacuum chamber allowed for determining the pressure profiles on the vacuum chamber and its lid. Numerical simulations were either conducted using a simulation program developed in the Visual Basic Applications (VBA) language for Microsoft Excel to model the degassing process in the vacuum chamber, or with the assistance of specialized software (transient structural analysis and simulation program in the ANSYS Workbench environment). Statistical analysis of the correlation between experimental and estimated pressure values revealed that both the proposed mathematical model and the solution method are well-chosen, with differences expressed through the absolute error (EA) being very small. Structural dynamic analysis carried through the Finite Element Method (FEM) highlights that the chosen materials for manufacturing the vacuum chamber vessel (316 stainless steel) or the chamber lid (transparent acrylic plastic) are durable and capable of withstanding the desired pressure and temperature demands in the seed treatment process. Additionally, through structural dynamic analysis, it was possible to study the deformation of system components, providing a detailed perspective on their structural distribution.

The soil-structure interaction represents an important parameter when analyzing the dynamic behavior of bridges, taking into account the integration between soil, foundation, and structure to ensure an adequate structural representation. In this paper, a computational modeling strategy using soil-structure interaction (SSI) methodology was applied to represent the dynamic behavior of a pedestrian bridge (LOP). The computational models were validated using monitoring results from an extensive structural health monitoring campaign. The bridge monitoring program was characterized using embedded sensors and cutting-edge technology for remote monitoring: ground-based radar interferometry and video motion amplification. The instrumentation results were compared to establish the capabilities and advantages of this novel remote monitoring technique. The experimental results obtained from free and forced vibrations in the asset served as a basis for validating the developed computational model and allowed evaluating the asset be-havior in service for different loading conditions. This paper emphasizes the SSI approach to represent the pedestrian bridge dynamic behavior more accurately, allowing computational models to represent the LOP structural responses over the course of its life-cycle.

In the new period, the state has made every effort to promote the new urbanization of public sports service. Entropy method, coupled coordination model, cold hot spot analysis is used to explore the dynamic relationship between public sports services and the development of new urbanization in China from 2008 to 2017. The results show that: (1) The development of the internal subsystem of public sports service is not balanced, the sports financial investment system grows rapidly, but the development of professional sports talent team is slow. (2) The imbalance of regional development cannot be ignored, and the public sports service level shows a decreasing gradient from east to west. (3) The regional development features are different. The eastern region is dominated by the coordinated development of sports public service and urbanization, while the central region is mainly in the type of public sports service lag, while the western region has multiple complex characteristics of low-level coordination and public sports service lag. Therefore, it is proposed that the construction of modern public sports service system should be investigated in the context of the development of new urbanization. It should be promoted from the following aspects: promoting the extension of public sports service to rural areas, engendering the "citizen's right" of sports health to the migrant population, conforming to the trend of mass sports intelligence, developing green sports and revitalizing idle sports assets in cities.

Computational simulations of three-dimensional flow around a NACA 0018 wing with an aspect ratio of AR=5 are carried out using the Unsteady Reynolds-Averaged Navier-Stokes (URANS) equations with the Shear-Stress Transport turbulence model closure. Simulations were performed to capture the aerodynamic stall hysteresis using a developed Pseudo-Transient Continuation (PTC) method based on a dual time step approach in the CFD code OpenFOAM. The flow was characterized by an incompressible Mach number of M=0.12 and a moderate Reynolds number Re=0.67×10^6. The results obtained indicate the presence of a noticeable aerodynamic hysteresis in the static dependencies of the force and moment coefficients, as well as the manifestation of bi-stable flow separation patterns, accompanied by the development of asymmetry in the stall zone. The URANS simulation results are in good agreement with the experimental data obtained for the NACA 0018 finite aspect ratio wing from the low-speed wind tunnel under the same test conditions. A new phenomenological bifurcation model of aerodynamic stall hysteresis under static and dynamic conditions is formulated, which is proven to be able to closely match the experimental data.

Computer extended Descriptive Geometry (CeDG) is a new approach to solve and build computer models of three dimensional (3D) geometrical systems through descriptive geometry procedures that have demonstrated reliability and accuracy. CeDG may calculate a parametric algebraic exact form for the spatial curves generated in the intersection of two surfaces, as well as of the flattened pattern of any developable surface involved in those encounters. This study presents first the theoretical foundations and methodology to calculate those parametric algebraic curves. Secondly, a compound hopper is defined and modelled through CeDG (implemented in GeoGebra) and CAD (Solid Edge 2023) approaches to evaluate the advantages of CeDG against CAD. The results demonstrate the robustness and accuracy of the CeDG technique for surfaces intersection and flattening and the advantages of CeDG against Solid Edge 2023 in solving the hopper case study.

Estimating the vehicle crashworthiness parameters experimentally is expensive and time consuming. For these reasons different modelling approaches are utilized to predict the vehicle behaviour and reduce the need for full-scale crash testing. The earlier numerical methods used for vehicle crashworthiness analysis were based on the use of lumped parameters models (LPM), a combination of masses and nonlinear springs interconnected in various configurations. Nowadays, the explicit nonlinear finite element analysis (FEA) is probably the most widely recognized modelling technique. Although informative, finite element models (FEM) of vehicle crash are expensive both in terms of man-hours put into assembling the model and related computational costs. A simpler analytical tool for early analysis of vehicle crashworthiness could greatly assist the modelling and save time. In this paper a simple piecewise LPM composed of a mass-spring-damper system, is used to estimate the vehicle crashworthiness parameters, focusing on the dynamic crush and the acceleration severity index (ASI). The model is first calibrated against a full-scale crash test and a FEM, post-processed with the LS-DYNA software, at an impact velocity of 56 km/h. The genetic algorithm is used to calibrate the model by estimating the piecewise lumped parameters (stiffness and damping of the front structure of the vehicle). After calibration, the LPM is applied to a range of velocities (40, 48, 64 and 72 km/h). The predictions for crashworthiness parameters from the LPM were compared with the predictions from the FEA and the results are much similar. It is shown that the LPM can assist in crash analysis, since LPM has some predictive capabilities and requires less computation time in comparison with the explicit nonlinear FEA.

Monitoring the dynamic responses of bridge structures has received considerable attention. It is important to synchronously measure both the quasi-static and dynamic displacements of bridge structures. However, the traditional accelerometer method cannot capture the quasi-static displacement component, although it can detect the dynamic displacement component. To this end, a novel composite instrument of a smartstation was proposed to monitor vibration displacements of footbridges. Full-scale experiments were conducted on a footbridge to validate the feasibility of the composite instrument-based monitoring method. A Chebyshev filter and wavelet algorithms were developed to process the composite instrument measurements. It was concluded that the measurement noise of the composite instrument was mainly distributed in a frequency range of 0–0.1 Hz. In two case studies with displacement peaks of 5.7–10.0 mm and 1.3– 2.5 mm, the composite instrument accurately identified the quasi-static and dynamic displacements. The composite instrument will be a potential tool for monitoring structural dynamics because of its enhanced overall performance.

Automobile proving ground is important for the research of vehicles which is used for the vehicle dynamics, durability testing, braking testing, etc. However, the roads in automobile proving ground will inevitably be damaged with the extension of the service life. In most previous researches, equipment similar to laser cross-section was used to detect pavement quality, the principle of which was to reflect pavement quality by detecting road surface roughness. This method ignores the elastic deformation of the roads itself when the vehicle is traveling on it and hardly compensate for the amendment. Therefore, this article presents a new method based on force sensor to reduce the impact of elastic deformation such as wheel tyre deformation, pavement deformation, and wheel rim deformation. In which, force sensors mounted on the wheels collect the three-dimensional dynamic load of the wheel.The presented method has been tested with two sets of cobblestone road load data, and the results show that The　incentives imposed by the test vehicle on the target road are 88.3%, 91.0%, and 92.05% of the incentives imposed by the test vehicle on the standard road in three dimensions, respectively. It is clear that the proposed method has strong potential effectiveness to be applied for lose detection of the special road application.

The purpose of the study was to find the source of complaints and to diagnose dynamic upper respiratory tract problems, which were derived from the horse owners, trainers, and jockeys, and to evaluate the overground endoscopic examination efficiency to determine the subclinical upper respiratory tract (URT) abnormalities, which were unable to diagnose with resting endoscopy. In the study, overground endoscopy has been used which nowadays there is a more useful and safe technique of performing endoscopy during ridden exercise in the natural field to diagnose dynamic upper respiratory tract (URT) abnormalities in comparison with the more traditional method of resting endoscopy. This study focused on 25 racehorses (Thoroughbred, n:22 and Arabian n: 3), which were admitted to Racehorse Hospital with complaints of fade abruptly and/or abnormal respiratory noise during the last meters of the race. All horses were examined for the complaints to be associated with systemic disorders and/or lameness, the racehorses with lameness and/or systemic disorders findings were excluded. Resting (post-exercise) and overground endoscopy by using Dr. Fritz® ETL-Equine Overground Endoscopy was performed on a polytrack racecourse in all racehorses. Observed abnormalities were recorded as simple and complex cases and the results of resting and dynamic examination were compared. It was concluded the overground endoscopic examination has a useful diagnostic value in determining the cause of abnormal respiratory noise and/or fade abruptly.

China is a traditional agricultural country, and the integration of rural industries has become an essential policy direction for the current strategy of agricultural modernization in China. In recent years, the agricultural industrial chains across various regions of China have consistently expanded and extended. The multifunctionality of agriculture is continuously unearthed, and the principal entities managing agriculture have become increasingly diversified and have grown significantly. New industries and forms in agriculture emerge incessantly. Accurately and profoundly understanding the inherent features of the integration of industries in rural China, establishing a scientific and rational measurement index system in line with the current status and development goals of rural China, and employing appropriate measurement methods to assess its development level and process, is instrumental in comprehending the level of integrated development in various regions. This aids in identifying challenges in the developmental process and proposing targeted developmental strategies. Hence, this paper, rooted in the integration of rural industries, cross-industry, industry extension, industry agglomeration, and industry penetration, sets up an measurement index system. Using provincial panel data from 2011 to 2020, the paper measures the level of integrated development in rural industries across China and its 31 provinces. Based on the measurement results, further techniques such as kernel density estimation and Gini coefficient decomposition have been used to analyze the spatial distribution characteristics and dynamic trends of the integrated development of rural industries in China. Research indicates that during the sample period, the overall level of integrated development in rural industries in various provinces in China has shown an upward trend. Development among the eastern, central, and western regions is highly uneven, but this disparity has been gradually narrowing in recent years. Furthermore, the levels of integrated development in different provinces exhibit significant spatial agglomeration effects. The development level of neighboring regions significantly impacts the province's development status. In the process of integrated development of rural industries in China, there's a trend where "it's easier to downgrade than to upgrade," with very few regions achieving leapfrog development.

Sulfur, peroxide and combined sulfur and peroxide curing systems were applied for cross-linking of unfilled and carbon black filled rubber compounds based on ethylene-propylene-diene-monomer rubber. The results revealed that the type of curing system influenced the course and shape of curing isotherms. This resulted in the change of curing kinetics of rubber compounds. The cross-link density of vulcanizates cured with combined vulcanization systems was lower than that for vulcanizates cured only in the presence of sulfur or peroxide system. The results revealed good correlation between the cross-link density as well as the structure of the formed cross-links and physical-mechanical characteristics of the materials. It can be stated that by proper combination of vulcanization systems it is possible to modify tensile behavior of vulcanizates in targeted manner. On the other side, dynamical-mechanical properties were found not be significantly influenced by the composition of curing system.

This study explores the capital structure determinants of Korean firms over an extensive period (1995-2021), encompassing both stable and crisis conditions. Employing a dynamic panel data model and the Generalized Method of Moments (GMM) estimation, we address the endogeneity issue introduced by the inclusion of lagged dependent variables. Our research integrates firm-specific internal factors with macroeconomic external variables to provide a comprehensive understanding of the influence of varying economic environments on capital structure. Our study suggests that in times of economic stability, the capital structure decisions of a firm are more influenced by internal factors such as profitability. However, in periods of economic downturns, it's the external macroeconomic market conditions that tend to have a greater impact on these decisions. It's also noteworthy that both book leverage (BL) and market leverage (ML) exhibit quicker adjustments during stable periods as opposed to periods of crisis. This indicates a higher agility of firms in adapting their capital structures in stable normal conditions. Our findings contribute to existing literature by offering a holistic view of capital structure determinants in Korean firms. They underscore the necessity of adaptable financial strategies that account for both internal dynamics and external economic conditions. This study fills a gap in current research, presenting new insights into the dynamics of capital structure in Korean firms and suggesting a multifaceted approach to understanding capital structure in diverse economic contexts.

This paper based on systems - theoretic approach to the definition of a country's GDP as not directly observable characteristic of system state. Leontief dynamic model is generalized to take into account the stimulating effect of consumption on GDP growth. In consumption, apart from final consumption, terms are considered: balance of foreign trade, fictitious investments and hidden costs. The Kalman filter uses Rosstat's gross output (for system output) and final consumption (for system control) data from 1995 to 2015. It is concluded that if in the years 2014, 2015 it was possible to increase consumption by 5% by, say, price cuts or some increase in money supply, then GDP would be greater by about 2.5%. GDP real values in recent years are most likely greater than official values. Fictitious investments and hidden costs are found in the amount of up to third the value of final consumption. The accuracy of one-year forecasts of true GDP by the methodology of this article is approximately 1.5%.

Rubber compounds based on styrene-butadiene rubber, ethylene-propylene-diene-monomer rubber and the combinations of both rubbers were cured with different sulfur and peroxide curing systems. In sulfur curing systems, two type of accelerators, namely N-cyclohexyl-2-benzothiazole sulfenamide, tetramethylthiuram disulfide and combinations of both accelerators were used. In peroxide curing systems, dicumyl peroxide, and combination of dicumyl peroxide with zinc diacrylate or zinc dimethacrylate, respectively were applied. The work was focused on investigation of the curing system composition as well as type of the rubber or rubbers combinations on curing process, cross-link density and physical-mechanical properties of vulcanizates. The dynamic-mechanical properties on the selected vulcanizates were examined, too. The result revealed correlation between the cross-link density and physical-mechanical properties. Similarly, there was recorded certain correlation between cross-linking degree and glass transition temperature. The tensile strength of vulcanizates based on rubbers combinations was higher when compared to that based on pure rubbers, which points out the fact that by rubbers combination, not only the features of both elastomers can be combined, but also improved tensile characteristics can be achieved. When compared to vulcanizates cured with dicumyl peroxide, materials cured with sulfur system exhibited higher tensile strength. By application of co-agents in peroxide vulcanization, the tensile strength overcame the tensile behavior of sulfur cured vulcanizates.

Asphalt binder is a temperature sensitive material, whose performance is greatly affected by the climate change of the environment. Improper selection of asphalt will cause a lot of damage and affect the durability of the road. The establishment of asphalt pavement performance zoning in Xinjiang, a vast area with great temperature difference, will provide reference for the selection of asphalt suitability, the refinement of pavement design and the sustainable development of road engineering. In this study, 11 years of temperature data in Xinjiang region were collected and analyzed, and 98% reliability of pavement design temperature was used to draw a performance grading map of asphalt pavement in Xinjiang region based on ArcGIS platform. Finally, Xinjiang region was divided into 9 performance zones. At the same time, the performance grade (PG) of five kinds of asphalt binders in Karamay were explored. The result shows that there is little difference in continuous PG span between different matrix asphalt binders, the lower penetration grade, the better high temperature performance, the worse low temperature performance. After adding SBS modifier, the continuous PG span can be higher than the matrix asphalt in 20 ℃. All these provide the basis for reasonable selection of asphalt binders in different areas of Xinjiang.

This paper proposes a Mixed Integer Conic Programming (MICP) model for community microgrids considering the network operational constraints and building thermal dynamics. The proposed multi-objective optimization model optimizes not only the operating cost, including fuel cost, purchasing cost, battery degradation cost, voluntary load shedding cost and the cost associated with customer discomfort due to room temperature deviation from the set point, but also several performance indices, including voltage deviation, network power loss and power factor at the Point of Common Coupling (PCC). In particular, the detailed thermal dynamic model of buildings is integrated into the distribution optimal power flow (D-OPF) model for the optimal operation. The heating, ventilation and air-conditioning (HVAC) systems can be scheduled intelligently to reduce the electricity cost while maintaining the indoor temperature in the comfort range set by customers. Numerical simulation results show the effectiveness of the proposed model and significant savings in electricity cost with network operational constraints satisfied.

The paper describes the research findings on dynamic and mechanical properties of composite elastomers with high permeability magnetic filling agent capable of rapidly and reversibly changing its properties when exposed to an external magnetic field, which makes it a perspective material for application in a wide range of engineering areas. The research has analyzed the trends in the strength properties of the materials obtained through the use of filling agents of different fineness, content, and structural organization in the final polymer, under different conditions. This allowed to obtain the correlations between the influence of the filler's relative fineness on the dynamic and mechanical properties of composite polymers, and to estimate the trends in the parameters describing the material strength under the complex magnetic and thermal influence. The results obtained by the authors allowed to ground the composition and structural organization of the final material with the best set of dynamic and mechanical properties.

Emergency control load-shedding is a key solution to prevent blackouts in the power system. This paper proposed a new model of emergency controls load shedding based on the fast identification of the unstable state of the power system. K-means clustering algorithm divided the instability mode into the clusters. The results of analysis of this cluster were used as the basis for classification control. Building load shedding strategies is consisted of the pre-designed rules based on AHP algorithm. When the recognition of the power system “instability” is detected, the signal of load shedding control is triggered immediately, therefore the decision time is greatly shortened comparing to the traditional methods. The effectiveness of the proposed method was tested on the IEEE 39-bus to overcome the limitations of the last traditional methods.

Ransomware constitutes a distinctive category of pernicious software that sequesters a user's digital assets by encryption, holding them hostage until a sum is extorted from the victim. These incursions have escalated to become among the most prevalent and significant threats confronting both individuals and corporate entities. In combatting this virulent program, dynamic analysis has been established as the favored detection modality. Such analyses typically hinge on Windows API calls, the conduits through which programs requisition services from the operating system. Yet, the superfluous and unrelated Windows API calls interjected by adversaries into the execution stream of suspect binaries precipitate an excessively noisy behavioral sequence, which impairs the performance of counter-ransomware mechanisms. The research outlined herein introduces a novel non-signature-based detection paradigm that harnesses efficacious Windows API call sequences through supervised machine learning strategies. An innovative Enhanced Min Max (EmRmR) filter technique is proposed, aiming to purge noisy features and isolate the most indicative feature subset that encapsulates the ransomware's true behavior. The EmRmR method, diverging from the traditional Min Max approach, circumvents the superfluous calculations that are a hallmark of the conventional algorithms, thereby necessitating a reduced number of evaluations. Additionally, a refinement procedure has been integrated to contract the program's call trace volume by discarding those Windows API calls lacking a robust correlation with ransomware's pivotal behavior. Subsequent to rigorous experimental analyses and juxtaposition with extant behavior-based detection methodologies, the proposed strategy has demonstrated its efficacy in differentiating ransomware behavior, delivering high detection precision alongside a diminution in false-positive occurrences.

The traditional Simultaneous Localization and Mapping (SLAM) systems are based on the 1 strong static assumption, and their performance will degrade significantly due to the presence of 2 dynamic objects located in dynamic environments. To decrease the effects brought by the dynamic 3 objects, based on ORB-SLAM2 system framework, a novel dynamic semantic SLAM system called 4 MOR-SLAM is presented using mask repair method, which can accurately detect dynamic objects 5 and realize high-precision positioning and tracking of the system in dynamic indoor environments. 6 First, an instance segmentation module is added to the front end of ORB-SLAM2 to distinguish 7 dynamic and static objects in the environment and obtains a preliminary mask. Next, to overcome the 8 under-segmentation problem in instance segmentation, a new mask inpainting model is proposed to 9 ensure that the integrity of object masks, which repairs large objects and small objects in the image 10 with depth value fusion method and morphological method respectively. Then, a reliable basic matrix 11 can be obtained based on the above repaired mask. Finally, the potential dynamic feature points 12 in the environment are detected and removed through the reliable basic matrix, and the remaining 13 static feature points are input into the tracking module of the system to realize the high-precision 14 positioning and tracking in dynamic environments. The experiments on the public TUM dataset 15 show that, compared with ORB-SLAM2, the MOR-SLAM improves the absolute trajectory accuracy 16 by 95.55%. In addition, compared with DynaSLAM and DS-SLAM on the high-dynamic sequences 17 (fr3/w/rpy and fr3/w/static), the MOR-SLAM improves the absolute trajectory accuracy by 15.20% 18 and 59.71%, respectively

The purpose of this study was to compare Electromyographic (EMG) with Mechanomyo- 1 graphic (MMG) recordings during isometric conditions, and during a simulated load-lifting task. 2 Twenty-two males (age: 25.5 ± 5.3 years) first performed maximal voluntary contractions (MVC) and 3 submaximal isometric contractions of upper limb muscles at 25%, 50% and 75% MVC. Participants 4 then executed repetitions of a functional activity simulating a load-lifting task above shoulder level, 5 at 25%, 50% and 75% of their maximum activity (based on MVC). The low frequency part of the 6 accelerometer signal (< 5 Hz) was used to segment the 6 phases of the motion. EMG and MMG were 7 both recorded during the entire experimental procedure. Root mean square (RMS) and mean power 8 frequency (MPF) were selected as signal extraction features. During isometric contractions, EMG 9 and MMG exhibited similar repeatability scores. They also shared similar RMS vs force relationship, 10 with RMS increasing to 75% MVC and plateaued to 100%. MPF decreased with increasing force to 11 75% MVC. In dynamic condition, RMSMMG exhibited higher sensitivity to changes in load than 12 RMSEMG. These results confirm the feasibility of MMG measurements to be used during functional 13 activities outside the laboratory. It opens new perspectives for future applications in sports science, 14 ergonomics and human-machine interfaces conception.

The process of identifying and approving a new drug is a time-consuming and expensive procedure. One of the biggest issues to overcome is the risk of hepatotoxicity, which is one of the main reasons for drug withdrawal from the market. While animal models are the gold standard in preclinical drug testing, the translation of results into therapeutic intervention is often ambiguous due to interspecies differences in hepatic metabolism. The discovery of human induced Pluripotent Stem Cells (hiPSCs) and their derivatives has opened new possibilities for drug testing. We used mesenchymal stem cells and hepatocytes both derived from hiPSC, together with endothelial cells, to miniaturize the process of generating hepatic organoids. These organoids were then cultivated in vitro using both static and dynamic cultures. Additionally, we tested spheroids composed solely by induced hepatocytes. By miniaturizing the system, we demonstrated the possibility of maintaining the organoids, but not the spheroids, in culture for up to 15 days. This timeframe may be sufficient to carry out a hypothetical pharmacological test or screening. In conclusion, we propose that the hiPSC-derived liver organoids model could complement or, in the near future, replace the pharmacological and toxicological tests conducted on animals.

This paper has designed a four-channel wide dynamic microwave rectifier circuit for the shortcomings of uneven output voltage of each branch of the multi-channel rectification technology. A voltage-doubling rectifier circuit with identical structure was used in each branch. The four rectifier branches shared the same load at the output terminal, allowing the rectifier circuit to have an RF-DC conversion efficiency greater than 50% over the input power range from 12mW to 274mW, widened by 274% compared to a single channel. Not only the advantages of multi-channel technology with wide dynamics were retained, but also the output voltage was highly consistent and could be directly output in parallel without complex power electronics conversion.

The heterogeneous structure implies that a few nodes may be crucial in maintaining network structural and functional properties. Identifying these crucial nodes correctly and quickly is a primary issue as contemporarily may face the mushrooming of large-scale datasets. Besides, the ‘weight issue’ is always ignored in this field which edge weight may play a positive/negative role in contributing to the node importance in different weighted networks. This paper provides a novel algorithm, Weighted Expectation Algorithm (WEA), which aims to ensure accuracy and speed of computation by taking advantage of dynamic programming to better handle the task of large-scale networks. Additionally, the weight issue that edge weights may contribute differently is addressed by a simply quantitative definition. Two standard experiments show WEA can maintain the network structure in connectivity well (by the lowest average robustness 0.192) and identify the node importance better in the spreading function test of spreading dynamics (by the highest average Kendall’s tau-b 0.678). In addition, the time complexities of different algo-rithms are evaluated, and their time-consuming are tested, proving that WEA consumes a rela-tively short time.

A proxy war, between a coalition of countries, BLUE and a country, RED, is considered. RED wants to increase the size of the RED territory. BLUE wants to involve more regions in trade and other types of cooperation. GREEN is a small and independent nation that wants to become a member of BLUE. RED attacks GREEN and tries to invade. BLUE decides to give optimal arms support to GREEN. This support can help GREEN in the war against RED and simultaneously reduce the military power of RED, which is valuable to BLUE, also outside this proxy war, since RED may confront BLUE also in other regions. The optimal control problem of dynamic arms support, from the BLUE perspective, is defined in general form. The objective function is a weighted sum of the present value of the free GREEN territory and the present value to BLUE of the net loss of military resources in the RED army. The net loss of RED at a particular point in time is a function of the location of the front line and the size of the mobile GREEN forces behind the RED line. First, it is assumed that the expected net loss is proportional to the force ratio behind the red front line. It is proved that the net loss function is a strictly concave quadratic function of x, the location of the front line. It is also proved that the unique maximum of the net loss function occurs at the same front location, also if the net loss function is proportional to the strength ratio behind the RED lines, raised to any strictly positive exponent. From the BLUE perspective, there is an optimal position of the front. This position is a function of the weights in the objective function and all other parameters. Optimal control theory is used to determine the optimal dynamic BLUE strategy, conditional on a RED strategy, which is observed by BLUE military intelligence. The optimal arms support strategy for BLUE is to initially send a large volume of arms support to GREEN, to rapidly move the front to the optimal position. Then, the support should be almost constant during most of the war, keeping the war front location stationary. In the final part of the conflict, when RED will have almost no military resources left and tries to retire from the GREEN territory, BLUE should strongly increase the arms support and make sure that GREEN rapidly can regain the complete territory and end the war

Fuel consumption, subsequent emissions and safe operation of class 8 vehicles are of prime importance in recent days. It is imperative that the vehicle operates in its true optimal operating region given a variety of constraints such as road grade, load, gear shifts, Battery State of charge (for hybrid vehicles), etc. In this paper a research study is conducted to evaluate the fuel economy and subsequent emission benefits when applying predictive control to a mild hybrid line haul truck. The problem is solved using a combination of dynamic programming with back tracking and model predictive control. The specific fuel saving features that are studied in this work are dynamic cruise control, gear shifts, vehicle coasting and torque management. These features are evaluated predictively as compared to a reactive behavior. The predictive behavior of these features are a function of road grade. The result and analysis shows significant improvement in fuel savings along with NOx benefits. Out of the control features dynamic cruise (predictive) control and dynamic coasting showed the most benefits while predictive gear shifts and torque management (by power splitting between battery and engine) for this architecture did not show fuel benefits but provided other benefits in terms of powertrain efficiency.

In this paper, drug treatment and vaccination are compared healthy and economically. In this comparison, in addition to comparing economic costs, it has paid attention to patients' recovery. To reach the goal, the prevalence of Covid-19 virus in New York is modeled by using the SEIR dynamic model. The SEIR dynamic model is used to model the period of epidemic diseases. Then, three disease control scenarios are evaluated economically. Treatment and vaccination are two important issues in controlling epidemic diseases. To control the disease, each of these two methods has economic costs and benefits. The main purpose of this paper is to compare the two methods of vaccination and treatment economically. Although the results of the study show that vaccination can be effective in preventing the epidemic of the disease than treatment, but due to the high cost and genetic mutation of the virus, vaccination is not the optimal method for both health and the economy in the long term.

This paper puts forward an alteration for Tensor Calculus utliized in a coordinate system which is under a dynamic distortion drawing inspiration from similar fields such as the Calculus of Moving Surfaces (CMS). The paper establishes transformation laws for Tensors within these regions and establishes Operators such as the Tensorial Field Derivative which enforce a Tensorial Transformation on Tensors defined within a Dynamically Moving coordinate system. This variation of Tensor Calculus can be utilized to observe how disciplines such as QFT and Continuum Mechanics would change to accomodate for a distorting coordinate system and can be utliized to develop new theoretical models which account for this temporal distortion particularly within Biological Settings.

Websites and applications use personalisation services to profile their users, collect their patterns and activities and eventually use this data to provide tailored suggestions. User preferences and social interactions are therefore aggregated and analysed. Every time a user publishes a new post or creates a link with another entity, either another user, or some on-line resource, new information is added to the user profile. Exposing private data does not only reveal information about single users' preferences, increasing their privacy risk, but can expose more about their network that single actors intended. This mechanism is self-evident on \emph{social networks} where users receive suggestions based on their friends' activity. We propose an information theoretic approach to measure the differential update of the anonymity risk for time-varying user profiles. This expresses how privacy is affected when new content is posted and how much third party services get to know about the users when a new activity is shared. We use real Facebook data to show how our model can be applied on a real world scenario.

MEMS (Micro-electromechanical Systems) becomes important increasingly due to the smarter and smaller fuze used in OICW (Objective Individual Combat Weapon). MEMS Safety and Arming (S&A) device is employed in different platforms and regions for small caliber projectile. Therefore, it is necessary to make a parametric study of the MEMS S&A device in different apply environments and explore the main sensitive factors of the MEMS S&A device to provide reference for designs. In this paper, based on the MEMS S&A device designed by our term, theory and finite element models are established, and the centrifugal insurance mechanism of the MEMS S&A device is parametric studied under the different speeds, temperature and thickness of the model by nonlinear dynamic method. By comparing the experimental and predicted results, the established FEM model is verified, and the conclusion is that the temperature and the centrifugal force are the main sensitive factors in the centrifugal insurance mechanism. In summary, we can suggest that the application environment, which the MEMS S&A device is suitable for, is the temperature equal to or slightly greater than normal temperature and the rotating speed higher than35000r/min of small caliber projectile.

Current stock market forecasting methods encompass fundamental, technical, emotional, and bargaining factors. Predominantly, price prediction hinges on order volume and price, although correlating these two within existing models proves challenging. This study employs Cycle Generative Adversarial Network (Cycle GAN) to unravel the intricate price-volume relationship, combining it with Bollinger Bands for trading signal analysis, overcoming hurdles in short-term forecasting prevalent in numerical analysis and AI. Focusing on TSMC (2330.TW) stock price, the research leverages Cycle GAN in deep learning to master the price-volume nexus, juxtaposed with LSTM and RNN. Historical TSMC closing prices and transaction counts are model inputs, scrutinizing their interconnectedness for predictions. This innovative approach aligns stock price, volume, market value, taxes, and prior changes via system engineering. By intertwining Bollinger Bands with stock price forecasts, trading signals are distilled, factoring in extended index %b for a comprehensive market picture.

Opportunistic routing is the latest technique that uses the broadcasting nature of the wireless medium to increase the number of potential forwarding nodes in the network. This, in turn improves the delivery rate and reliability of data transmission in the network. Compared to all previous classes of routing protocols, opportunistic routing offers numerous advantages which is exploited by the latest applications for efficient communication and resource sharing in dynamic ad hoc networks. These applications provide dynamic communication in disaster recovery environments. The objective of this research work is to review and classify all the major opportunistic routing protocols proposed for dynamic ad hoc networks. Further the issues and challenges with each of these existing protocol is discussed and future research directions are put forward

Chymotrypsin is an important proteolytic enzyme in human digestion system that cleaves milk proteins, through hydrolysis reaction, which makes it interesting subject to study activity of milk proteases. In this work, we compared detection of chymotrypsin by spectrophotometric, dynamic light scattering (DLS) and quartz crystal microbalance (QCM) methods and determined the limit of chymotrypsin detection (LOD), 0.15 ± 0.01 nM for spectrophotometric, 0.67 ± 0.05 nM for DLS and 1.40 ± 0.30 nM for QCM methods, respectively. We discuss peculiarities and give perspective for implementation of detection methods and note that while the optical detection methods are simple to implement, the QCM method is more robust for sample preparation. We give an overview on methods and instruments for detection of chymotrypsin and other milk proteases.

This research investigated the antihypertensive effects of tamarind products and compared their potentials based on their animal model’s data verified by molecular docking, multitarget interactions in network pharmacology, and dynamic simulation assays. The GC-MS characterized tamarind products were administered to the cholesterol-induced hypertensive Wistar albino rat models. Two-week-intervened animals were dissected to collect serum and organs which were respectively subjected to the analyses of hypertension-linked markers and tissue architectures. Lead biometabolites of tamarinds interacted with eight target receptors in molecular docking and dynamic simulation studies and they were tested for multitarget interactions using network pharmacological analyses. Results showed that serum alanine aminotransferase (ALT), aspartate aminotransferase (AST), alkaline phosphatase (ALP), C-reactive protein (CRP), Troponin I, and lipid profiles were maximally reinstated by the phenolic-enriched ripened sour over the sweet tamarind flesh extracts, but seed extracts had a smaller influence. Among the tamarind’s biometabolites, Gamma-sitosterol (ϒ-sitosterol) was found to be the best ligand in managing hypertension via the possible ligand-receptor interactions with the guanylate cyclase which displayed the best drug-likeliness through the highest binding energy -9.3 Kcal. Multitargeted interactions-based degree algorithm and phylogenetic tree of pathways showed 14 targeted genes, of which NR3C1, REN, PPARG, and CYP11B1 hub genes, were consistently modulated by the ϒ-sitosterol to reduce hypertension and related risk factors. The dynamic simulation study showed that the P-RMSD values of ϒ-sitosterol-guanylate cyclase were stable between 75.00 to 100.00 ns at the binding pocket. The findings demonstrate that ripened sour tamarind extract may be supplemented to be a more prospective antihypertensive target or nutraceuticals affirming through advanced preclinical and clinical studies.

The Covid-19 crisis has been one of the most relevant economic shocks in the history of the modern economy, mainly due to the restrictions on travel and social interaction taken by the authorities (quarantines, closure of schools, artistic activities, bars, and restaurants, capacity in stores), to reduce the transmission of the virus (Sars-Cov2), having consequences on the national productions of all countries (about 7% for the loss of GDP worldwide). In our study, we analyze, through clustering methods, the effects of the level of contagion, economic projections, and economic mitigation measures taken by governments for managing the pandemic. According to the analyses, it can be concluded that a low infection rate implies a lower loss of product and economic savings when applying economic mitigation measures, taking relevance in the management of sanitary measures to reduce the transmission of the virus (and the temporality of these).