The hydrodynamic behavior of the air-acetic acid system in a bubble column is studied using a differential pressure transmitter, double probe optical fiber probe, and the electrical resistance tomography (ERT) technique. The superficial gas velocity ranges from 0.016 to 0.094 m/s under ambient temperature and pressure. The influences of viscosity and surface tension on gas holdup, bubble rising velocity, and bubble chord distribution in the column are discussed with different mass fractions of an acetic acid solution. The results show that as the mass fraction of acetic acid increases, the surface tension of the liquid phase decreases, and the viscosity first increases and then decreases. This causes the gas holdup in the column to first increase and then decrease, and reaches the maximum value at an acetic acid mass fraction of 55% to 60%. The rising velocity of the bubbles in the column is high in the central region and has a low-value distribution near the wall. The bubble chord length distribution is concentrated, and the distribution of the bubble chord length in the column becomes narrow with any decrease in surface tension. Studying the hydrodynamic behavior of a bubble column with the air-acid system is of great significance considering the absence of data on air-organic acid systems.

This work focuses on the support effect on the performances of Co-based catalysts for the acetic acid steam reforming. SBA-15, a well ordered hexagonal mesoporous silica structure, and CeO2 have been selected as the supports, with the impact of chromium addition also being investigated. Better acetic acid steam reforming performances have been recorded for CeO2 compared to SBA-15 supported catalysts and, in particular, the 7Co/CeO2 catalyst showed the highest values of acetic acid conversions with enhanced H2 yields below 480°C, in comparison to the other investigated catalytic formulations. In addition, more pronounced coke depositions and acetone concentrations have been obtained with CeO2 supported catalysts, due to the tendency of ceria to catalyse the ketonization reaction. Chromium addition to Co/SBA-15 catalysts led to an enhancement in the activity towards acetic acid steam reforming, while on CeO2 supported catalysts no improvement in the catalysts activity was observed; however, on both SBA-15 and CeO2 supported catalysts, Cr addition reduced the amount of coke deposited on the catalysts surface.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

Zinc is mostly extracted from zinc oxide and sulfide minerals, and this process involves flotation as a key step. While it is easier to float the sulfide mineral, its consumption and depletion has led to an increased reliance on zinc oxide minerals, including smithsonite; hence the development of efficient ways of collecting smithsonite by flotation is an important objective. Herein, we describe the use of 2-(hexadecanoylamino)acetic acid (HAA), a novel surfactant, as a collector during smithsonite flotation. The mechanism and flotation performance of HAA during smithsonite flotation were investigated by total organic carbon (TOC) content studies, zeta potential measurements, FTIR spectroscopy, and XPS analyses, combined with micro-flotation experiments. The flotation results revealed that HAA is an excellent collector in pulp over a wide pH range (9–12) and at a relatively low concentration (2 × 10^‒4 mol/L), at which a recovery of close to 90% of the smithsonite mineral was obtained. TOC-content studies reveal that the good flotation recovery is ascribable to large amounts of collector molecule adsorbed on the smithsonite surface, while zeta potential measurements show that the HAA is chemically adsorbed onto the smithsonite. FTIR and XPS analyses reveal that the HAA-collector molecules adsorb onto the smithsonite surface as zinc-HAA complexes involving carboxylate moieties and Zn sites on the smithsonite surface in alkaline solution.

Pyrolysis is a thermochemical conversion process designed for biomass decomposition in an oxygen-free environment. It typically operates within a temperature window of 200 to 800°C and generates various byproducts, including gases, liquid fractions (both aqueous and organic) such as bio-oil, and solids like char. Bio-oil is a significant product of pyrolysis. It is characterised by a complex blend of organic compounds. The acidic nature of bio-oil primarily originates from volatile acids, such as acetic acid. The recovery of acetic acid from bio-oil facilitates the use of the extracted substance as a precious resource, hence enhancing its significance in the framework of a circular bioeconomy. Acetic acid finds widespread application in manufacturing commercially important chemicals like vinyl acetate monomers and formulating phytosanitary products due to its inherent herbicidal and antifungal properties. However, to be used, acetic acid has to be separate from the raw bio-oil. Separation methodologies, including nanofiltration and reverse osmosis, demonstrate potential in recovering acidic constituents from bio-oil due to their high selectivity and effective system management. This article offers a concise review about acetic production from lignocellulosic biomass from pyrolysis and its recovery through various membrane separation processes.

Bacterial indole-3-acetic acid (IAA), an effector molecule in microbial physiology, plays an important role in plant growth-promotion. Here, we comprehensively analyzed about 7282 prokaryotic genomes representing diverse bacterial phyla, combined with root-associated metagenomic data to unravel the distribution of tryptophan-dependent IAA synthesis pathways and to quantify the IAA synthesis-related genes in the plant root environments. We found that 82.2% of the analyzed bacterial genomes were potentially capable of synthesizing IAA from tryptophan (Trp) or intermediates. Interestingly, several phylogenetically diverse bacteria showed a preferential tendency to utilize different pathways and tryptamine and indole-3-pyruvate pathways are most prevalent in bacteria. About 45.3% of the studied genomes displayed multiple coexisting pathways, constituting complex IAA synthesis systems. Furthermore, root-associated metagenomic analyses revealed that rhizobacteria mainly synthesize IAA via IAM and tryptamine (TMP) pathways and might possess stronger IAA synthesis abilities than bacteria colonizing other environments. The obtained results refurbished our understanding of bacterial IAA synthesis pathways and provided a faster and less labor-intensive alternative to physiological screening based on genome collections. The better understanding of IAA synthesis among bacterial communities could maximize the utilization of bacterial IAA to augment the crop growth and physiological function.

Traditional grain vinegar is fermented using multiple acetic acid bacteria (AAB) at various temperatures. A single AAB showed high acid–producing ability at 30 °C with a 5% alcohol concentration and an initial pH adjusted to 4.0. Multiple AAB were similar to single AAB, but the optimal initial pH was 3.0. Acid production ability according to the type of AAB was higher in multiple AAB than that for single AAB. That is, using multiple AAB helped to increase the titratable acidity of traditional grain vinegar. In addition, increasing the titratable acidity and content of volatile flavor compounds was advantageous when two, rather than four, AAB types were mixed and used. Titratable acidity was high at medium temperatures (30 °C), but volatile flavor compounds increased at low temperatures (20 °C) under multiple AAB. A 16S rDNA–based microbiome taxonomic profiling analysis identified differences in beta diversity due to multiple AAB and fermentation temperatures. In particular, beta diversity analysis revealed a specific pattern when a mixture of Acetobacter ascedens GV–8 and Acetobacter pasteurianus GV–22 were fermented at low temperature (20 °C). Therefore, we propose the application of multiple AAB with acidic and flavor–producing properties in traditional grain vinegar.

Biomass as a whole offers a more diverse potential for valorisation than any other renew-able energy source. As one of the stages in the separation of bio-oil involves the liquid mixture of acetol and acetic acid, and as both components are particularly well suited for valorisation, a hybrid method has been developed for their separation with a high purity level through an approach combining liquid-liquid extraction and rectification. In order to design and simulate the flowsheet, the ChemCAD 7.0 simulation software has been used. Sensitive analyses have been carried out to investigate the influence of the different pa-rameters in the rectification columns such as the reflux ratio, the feed stage location, and the vapour/bottom molar flow ratio. The effect of different extractants and of their excess on the separation process as well as the possibility of regenerating the extractant has also been studied. Tri-n-octylamine has accordingly been selected as a separating agent which has been fully recycled. The end result for separating an initial 48/52 wt% ace-tol/acetic-acid liquid mixture has been acetol with a purity of 99.4 wt% and acetic acid with a purity of 100 wt%.

An original approach has been proposed for designing a nanofibrous (NFs) layer using UV-cured polyvinylpyrrolidone (PVP) as a matrix, incorporating mesoporous graphene carbon (MGC) nanopowder both inside and outside the fibres, creating a sandwich-like structure. This architecture is intended to selectively adsorb and detect acetic acid vapours, which are known to cause health issues in exposed workers. The nanocomposite MGC-PVP-NFs layer was fabricated through electrospinning deposition onto interdigitated microelectrodes (IDEs) and stabilised under UV-light irradiation. To enhance the adhesion of MGC onto the surface of the nanocomposite polymeric fibres, the layer was dipped in a suspension of polyethylenimine (PEI) and MGC. The resulting structure demonstrated promising electrical and sensing properties, including rapid responses, high sensitivity, good linearity, reversibility, repeatability, and selectivity towards acetic acid vapours. Initial testing was conducted in a laboratory using a bench electrometer, followed by validation in a portable sensing device based on consumer electronic components (by ARDUINO®). This portable system was designed to provide a compact, cost-effective solution with high sensing capabilities. Under room temperature and ambient air conditions, both laboratory and portable tests exhibited favourable linear responses, with detection limits of 0.16 and 1 ppm, respectively.

Indole-3-acetic acid (IAA) is a key vegetative hormone that plays crucial roles in plant growth and development. In this study, the effect of the exogenous application of IAA as a biostimulant in the cultivation of onions (Allium cepa) was investigated. Different IAA concentrations were evaluated to determine their effects on onion growth and chemical parameters. Various physical and chemical parameters such as total fresh weight, plant height, chlorophyll content, nitrates, total phenols, and antioxidant capacity (DPPH) were analyzed. The results revealed that exogenous application of IAA had a significant impact on onion growth and quality. Specifically, it was found that certain concentrations of IAA fostered a greater fresh weight of the bulb, an increase in the levels of phenolic compounds and a greater DPPH. However, the onion response to IAA was dependent on the concentration. In conclusion, the present study provides evidence that the exogenous application of IAA as a biostimulant can improve onion growth and quality. These results are relevant for the development of sustainable agricultural practices and could be oriented towards crop improvement.

The alcoholic fermentation process with agitation/static, followed by the acetic fermentation submerged in banana was evaluated. Kinetics parameters of alcoholic fermentation for the maximum ethanol/glycerol metabolites in agitated process was 29 and 27 h, and in static 47 and 45 h, respectively. For acetic fermentation, the kinetics parameters were medium time of 39.9 h, acetic acid yield of 53.1% and acetic acid productivity of 0.216 g/Lh. Wines from agitated/static process presented 5.73 and 6.81% (v/v) of alcohol content, respectively. Wine obtained by the static process presented higher concentrations of volatile compounds. The vinegar showed 49.2 g/L of acetic acid and the esters concentrations were higher than in wine. The wine and vinegar minerals were consistent with amount observed in the pulp, with an increase in sulphur concentration after alcoholic fermentation and decrease after acetic fermentation. Products showed chemical and composition of sensory and nutritional interest.

Acetic acid bacteria (AAB) form a bacterial film on the surface of alcoholic solutions and ferment ethanol to acetic acid while also producing bioactive compounds. To discover functional AAB for industrial use, we isolated and selected strains from farm-produced vinegars using a CaCO3-containing medium. The seven strains belonged to Acetobacter cerevisiae and A. pasteurianus. Physiological properties were determined, including ethanol tolerance at up to 12% (v/v). Acidification at a growth temperature of 40 ℃ was seen for GHA 7, GYA 23, JGB 21-17, and GHA 20 strains, which may be useful in vinegar production where thermotolerant AAB are required. The seven AAB isolates had strong antibacterial activity against Staphylococcus aureus. Antioxidant activity was 2- and 4-fold higher, respectively, for A cerevisiae and A. pasteurianus than for the control, 1% acetic acid. We also observed 91.3% inhibition of angiotensin-converting enzyme activity for the KSO 5 strain, higher than that for the positive control, 0.1% captopril (76.9%). All strains showed complete inhibition of α-glucosidase, except JGB 21-17 and GHA 7 with 98.3% inhibition. Our work suggests usefulness of the strains selected as seed strains for highly efficient production of functional vinegar and illustrates identification of useful functional characteristics on a scientific basis.

The present work aimed to validate a low-cost passive monitoring procedure. For its validation, the monitoring of atmospheric organic pollutants - polycyclic aromatic hydrocarbons (PAH) was carried out in a capital of the central-western region of Brazil. The sensors were fixed on poles intended for electrification during the dry season. After 15 days, samples were extracted by solvent extraction and analysed by High-Resolution Gas Chromatography with Flame Ionization Detector (HRGC-FID). For the validation of the procedure, PAHs monitored and standardised by the American Environmental Agency (EPA), a benchmark for environmental monitoring of air quality by several countries, were analysed. The results demonstrated that the low-cost passive monitoring method was effective in the quantification of PAH in the environment-air, capable of being used by countries that do not have many resources for monitoring air quality.

The (benzylthio)acetic acid (HBTA) and some aminopyrimidines, namely 2-aminopyrimidine (2-AP), 5-aminopyrimidine (5-AP), 2-amino-4,6-dimethylpyrimidine (2-A-4,6-DMP) and 2,4,6-triaminopyrimidine (2,4,6-TAP), were successfully embodied as structural units into the construction of a total of four novel supramolecular organic frameworks. The received crystalline solids were inspected by single crystal X-ray diffraction (SC XRD) in order to obtain insight into the structural and supramolecular facets. The SOFs deriving from 2-AP, 5-AP as well as 2-A-4,6-DMP crystallize in the form of true co-crystals (1-3), while the one originating from 2,4,6-TAP crystallizes as salt solvate (4). The SC XRD results indicated the different contents of structural residues present in the asymmetric units of the crystals 1-4 despite the using the same molar ratio of molecular co-formers in each case. The molecular structures of co-crystals 1-3 consist of either one neutral residue of each starting components (1 and 3) or a half nonionized residue of aminopyrimidine ingredient and one neutral residue of acidic specie (2). The asymmetric unit of salt solvate 4 is composed of two ionized residues of each co-former (two 2,4,6-TAP+ cations and two BTA- anions) and one MeOH solvent molecule. The most extensive H-bonding network is observed in the crystal structure of salt solvate 4. The relevant molecular ingredients in co-crystals 1-3 are mainly hold together by the neutral Ocarboxylic–H···Npyrimidine and Namine–H···Ocarboxylic H-bonds. In the case of aggregate 4, the corresponding ionic residues are predominantly sustained by the charged-assisted Npyrimidinium–H···Ocarboxylate and Namine–H···Ocarboxylate hydrogen interactions. The MeOH solvent incorporated into the crystal lattice of adduct 4 is also involved in H-bonding by simultaneously serving as the single donor in OMeOH–H···S and the single acceptor in Namine–H···OMeOH H-bonds afforded the structural diversity within the 2,4,6-TAP+ cations and BTA- anions. Other weaker sets of additional non-covalent contacts existing in the crystal structures of analyzed conglomerates are involved in the self-assembly, stabilization and expansion of total supramolecular organic frameworks. The fact of the formation of non-covalent bonded supramolecular organic frameworks in question is also reflected in corresponding results obtained through elemental analysis (EA), Fourier transform infrared spectroscopy (FT−IR) and thermal analysis (TG/DSC).

This paper describes a case study of ventilation as well as measured and perceived indoor air quality (IAQ) in a Finnish comprehensive school with a hybrid ventilation system and reported IAQ problems. An operational error was found when investigating the ventilation system that prevented air from coming into classrooms, except for short periods of high carbon dioxide (CO₂) concentrations. However, results indicated that hybrid ventilation system was able to provide adequate ventilation and sufficient IAQ once properly designed and maintained. After ventilation operation was improved, occupants reported less unpleasant odors and stuffy air. The amount of total volatile organic compounds (TVOC) and some single volatile organic compounds (VOCs) decreased. Indoor mycobiota was observed in settled dust in the classrooms, from which ventilation improvement eliminated the dominant, opportunistic human pathogen species Trichoderma citrinoviride found before improvement.

The indole-3-pyruvic acid pathway is the major route for auxin biosynthesis in higher plants. Tryptophan aminotransferases (TAA1/TAR) and members of the YUCCA family of flavin-containing monooxygenases catalyze the conversion of L-tryptophan via indole-3-pyruvic acid into indole-3-acetic acid (IAA). It has been described that locally produced jasmonic acid (JA) in response to mechanical wounding, triggers de novo-formation of IAA through the induction of two YUCCA genes, YUC8 and YUC9. Here, we report the direct involvement of a small number of basic helix-loop-helix transcription factors of the MYC family in this process. We show that the JA-mediated regulation of YUC8 and YUC9 gene expression depends on the abundance of MYC2, MYC3, and MYC4. In support of this observation, seedlings of myc knockout mutants displayed a strongly reduced response to JA-mediated IAA formation. In addition, transactivation assays provided experimental evidence for the binding of the MYC transcription factors to a particular tandem G-box motif abundant in the promoter regions of YUC8 and YUC9, but not in those of the other YUCCA genes. Moreover, we clearly demonstrate that YUC8ox and YUC9ox overexpressing plants show less damage after spider mite infestation, thereby underlining a role of auxin in plant responses toward biotic stress cues.

Numerical simulations and experiments on evaporative condensers in air conditioning systems using R744 were performed. Two configurations were given to study the feasibility of operating the subcritical R744 cycle. It indicated the capable of evaporative cooling condensing R744 to liquify by analyzing the outlet temperature at the end of the condenser reached from 28.7oC to 30.3oC with the operating pressure from 72.6 bar to 68.5 bar. The mass flow rate in the study increases from 14.34 kg/h to 46.08 kg/h, the pressure drop also increases from 0.23 bar to 0.47 bar for the simulation and 0.4 bar to 0.5 bar for the experiment, respectively. This study indicates that a 5-layers of copper tubes configuration causes a higher pressure drop and lower COP when compared to an 8-layers of copper tubes that split into 2 sets for smaller pressure drop. In this study, the evaporative condensers using mini tubes that are flooded in the cooling water tank are suitable for the subcritical R744 air conditioning system. The results obtained from the experimental data are in good agreement with those obtained from the numerical results, with the deviation less than 5%.

Asthma is a chronic respiratory disease that impairs breathing. Management of asthma presents a significant challenge due to its inherent variability; that is, its symptoms can substantially differ among individuals, thereby complicating the prediction and management of exacerbations. Furthermore, individuals with asthma often have unique triggers that precipitate symptoms or attacks. The identification of these triggers can often prove to be a challenging, and at times, an impractical attempt. To address this, our research proposes a practical, personalized alert system, predicated on individual lung function tests conducted under varying environmental conditions classified by air-quality sensors. To validate this concept, we conducted an observational pilot study involving healthy individuals. We recruited twelve healthy participants and monitored their responses across a broad spectrum of environments, characterized by varying air quality, temperature, and humidity conditions. The lung function for each participant, assessed using peak expiratory flow (PEF) values, was recorded in each of these environments. Our results highlighted substantial variability in pulmonary responses to different environments. Utilizing these insights, we proposed a personalized alarm system that provides real-time air-quality monitoring and issues alerts when environmental conditions may potentially become unfavorable. We also explored the feasibility of employing basic machine learning techniques to predict PEF values in the aforementioned environmental conditions. This proposed system has the potential to empower individuals in actively safeguarding their respiratory health and mitigating discomfort caused by environmental conditions, especially in cases of asthma patients. By enabling timely and personalized interventions, the system aims to provide individuals with the necessary tools to minimize exposure to asthma’s possible triggers.

A study was conducted on the power system of a forklift equipped with PEM fuel cells. A fuel cell assembly relies on several components for proper functioning, and among these, the air compressor holds paramount importance due to its significant energy consumption when compared to other Balance of Plant components. The air supply system, in turn, plays a critical role in ensuring the stable and efficient operation of the entire fuel cell system. To enhance system efficiency, we delved into the impact of varying the stoichiometric ratio of air and air pressure on the validated and optimized power module model. This investigation was carried out under real loading conditions, replicating the conditions experienced by the power module when fuel cells are in use within a forklift. The air compressor, being a pivotal component of a PEM fuel cell system, can be oper-ated at different excess air and pressure ratios, which in turn influence both the fuel cell's performance and the overall efficiency of the power module system. Our research focused on assessing the performance of polymer electrolyte membrane (PEM) fuel cells under different load cycles, adhering to the VDI60 requirements for forklift applications. This comprehensive examination encompassed the system's minimum and maximum load scenarios, with the primary goal of optimizing excess air and pressure ratio parameters, especially under dynamic load conditions. The results revealed that higher air pressures and lower excess air ratios were con-ducive to increasing system efficiency, shedding light on potential avenues for enhancing the performance of PEM fuel cell systems in forklift applications.

The paper describes and analyzes the performance of a new thermoelectric generation system based on the use of Peltier cells inserted in the ducts of the air conditioning equipment. The hot and cold air streams that flow in the two separated sections of an air conditioning system are used to create a thermal gradient between the two faces of the Peltier cells. Hot and cold air flow inside the A/C unit are driven to a built in thermal chamber where the Peltier cells are placed. Peltier cells are incrusted into an insulation wall that separates the two sections of the chamber through which hot and cold air streams are flowing. The so designed configuration allows the Peltier cells to generate electric current. The study has been run for constant cold air temperature and variable hot air temperature, resulting in a variable performance of the thermoelectric generator. Theoretical study has been completed with experimental tests to determine real performance of the thermoelectric unit. Efficiency of the thermoelectric generator has been found to be linearly dependent on the temperature difference between hot and cold air subsections of the chamber. Maximum efficiency, however, is limited by the hot air stream temperature, since in real conditions ambient temperature cannot overpasses a specific value. For standard operational conditions, 5º C and 45º C for the cold and hot air streams, the thermoelectric generator operates at 44% of the maximum efficiency attainable.

This work reports of the use of a bench scale chemostat (CSTR) in continuous mode and of a pilot scale membrane bioreactor (MBR) in fed-batch mode to intensively produce acetic and butyric acids using Cl. butyricum grown on synthetic media. These studies were then used to perform a cost estimation study of the MBR system to assess the potential economic impact of this proposed methodology. The MBR system was found highly productive reaching 37.88 g L-1 h-1 of acetic and 14.44 g L-1 h-1 of volumetric cell productivity, favoring acetic acid production to butyric at a ratio 3:1. The cost of preparation and production of carboxylic acids using this system was found as 0.0062 £PS/kg respectively and an up to 99% carbon recovery.

In order to produce bioethanol from yellow poplar sawdust without detoxification, deacetylation (mild alkali treatment) was performed with aqueous ammonia solution. To select the optimal conditions, deacetylation process was carried out using different conditions: NH₄OH loading (2–10% (w/v)) and solid-to-liquid ratio (1:4–10) at 121 °C for 60 min. In order to assess the effectiveness of deacetylation, fractionation of deacetylated yellow poplar sawdust was performed using dilute acid (H₂SO₄, 0.5–2.0% (w/v)), reaction temperature (130–150 °C) and time (10–80 min). The toxicity-reduced hemicellulosic hydrolysates that were obtained through a two-step treatment at optimized conditions were fermented using Pichia stipitis for ethanol production, without any further detoxification. The maximum ethanol production was 4.84 g/L, corresponding to a theoretical ethanol yield of 82.52%, which is comparable to those of intentionally made hydrolyzates as controls.

In 2011, commercial aviation contributed approximately 3.5% of global anthropogenic climate change through the emission of greenhouse gases during flight and operational non-CO2 climate effects. Over the last few years, numerous aviation-related organisations have set goals to reduce aviation’s climate impact. These goals, however, lack alignment, are poorly or ambiguously defined, or are internally inconsistent. This increases uncertainty about what aviation should work towards, how various stakeholders can contribute, and introduces problems with respect to accountability. In order to address this issue, this paper presents a comprehensive definition of a climate neutral air transport system as an “air transport system of which the climate effects of all its greenhouse gases and non-carbon dioxide effects throughout the entire life-cycle of each element of the system is balanced”. The proposed definition spans relevant system and encompasses all life cycle phases. To achieve a climate neutral air transport system by 2050, all life-cycle greenhouse gas emissions and non-CO2 climate effects remaining after in-sector reduction should be neutralised, as should all remaining non-CO2 climate forcing from emissions prior to 2050. Clarity on governance is furthermore needed, as the goal and associated targets proposed should be adopted globally.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

This paper, we examined the technology to maximize the use of renewable energy. The passive ventilation system is expected to reduce the energy consumption of the fan power and the maintenance burden. In addition, the wall-mounted solar air heater can supply thermal energy without using any energy at all. Therefore, we propose a "passive ventilation system with a solar air heater" that combines a passive ventilation system with solar air heater to preheat the air supply and reduce the ventilation load. To evaluate the solar air heater performance in a real environment, we developed a simulation for calculating the heat collection capacity of the solar air heater, and then implemented the system in a real building for verification. Based on the measurement results, the effects of heating load reduction and prediction methods are presented.

Recently, there has been growing interest in using smart eHealth systems to manage asthma. However, limitations still exist in providing smart services and accurate predictions tailored to individual patients’ needs. This study aims to develop an adaptive ubiquitous computing framework that leverages different bio-signals and spatial data to provide personalized asthma attack prediction and safe route recommendations. We proposed a smart eHealth framework consisting of multiple layers that employ telemonitoring application, environmental sensors, and advanced machine-learning algorithms to deliver smart services to the user. The proposed smart eHealth system predicts asthma attacks and uses spatial data to provide a safe route that drives the patient away from any asthma trigger. Additionally, the framework incorporates an adaptation layer that continuously updates the system based on real-time environmental data and daily bio-signals reported by the user. The developed telemonitoring application collected a dataset containing 665 records used to train the prediction models. The testing result demonstrates a remarkable 98% accuracy in predicting asthma attacks with a recall of 96%. The eHealth system was tested online by ten asthma patients, and its accuracy achieved 94% of accuracy and a recall of 95.2% in generating safe routes for asthma patients, ensuring a safer and asthma-trigger-free experience. The test shows that 89% of patients were satisfied with the safer recommended route than their usual one. This research contributes to enhancing the capabilities of smart healthcare systems in managing asthma and improving patient outcomes. The adaptive feature of the proposed eHealth system ensures that the predictions and recommendations remain relevant and personalized to the current conditions and needs of the individual.

Nowadays, energy saving is considered a key issue worldwide, as it brings a variety of benefits: reducing greenhouse gas emissions, reducing demand for energy imports, and lowering costs on a household and economy-wide level. Researchers and building designers are looking to optimize building efficiency by means of new energy technologies. Changes in existing buildings can also be made to reduce energy consumption and costs. These may include the usage of new heat transfer fluids based on nanofluids. In this work, an extended experimental campaign (from February 2020 to March 2021) has been carried out on an educational building in the Campus of University of Salento, Lecce – Italy, in order to evaluate the increase in performance of the HVAC system, due to the usage of a nanofluid. The results show that, under optimal operating conditions, plant performance improves more than 10%, with average daily peaks of about 15%.

Urban air quality is increasingly becoming a cause for concern for the health of the human population. The poor air quality is already wreaking havoc in major cities of the world, where serious health issues and reduction of average human life by a factor of years are reported. The air quality in developing countries can become worse as they undergo development. The urban air quality varies non-linearly depending upon the various factors such as land use, industrialization, waste disposal, traffic volume, etc. To address this problem, it is necessary to look at the plethora of available literature from multiple perspectives such as types and sources of pollutants, meteorology, urban mobility, urban planning and development, health care, economics, etc. In this paper, we provide a comprehensive survey of the state-of-the-art in urban air quality. We first review the fundamental background on air quality and present the emerging landscape of urban air quality. We then explore the available literature from multiple urban air quality measurement projects and provides the insights uncovered in them. We then take a look at the sources that are significantly contributing to polluting the air quality. Finally, we highlight open issues and research challenges in dealing with urban air pollution.

Plants are constantly exposed to a variety of different environmental stresses, including drought, salinity, and elevated temperatures. These stress cues are assumed to aggravate in the future driven by the global climate change scenario which we are currently experiencing. These stressors have largely detrimental effects on plant growth and development and, therefore, put global food security in jeopardy. For this reason, it is necessary to expand our understanding of the underlying mechanisms by which plants respond to abiotic stresses. Especially boosting our insight into the ways by which plants balance their growth and their defense programs appears to be of paramount importance, as this may lead to novel perspectives that can pave the way to increase agricultural productivity in a sustainable manner. In this review, our aim was to present a detailed overview of different factettes of the crosstalk between the antagonistic plant hormones abscisic acid (ABA) and auxin, two phytohormones that are the main drivers of plant stress responses, on the one hand, and plant growth, on the other.

In this paper, the experimental study of heating in 2 h lunch mode of air-conditioned bed system is carried out. The results show that the power consumption of heat conduction heating is only 0.34 kW·h, and the average heat dissipation is 81.3 W, while the power consumption of convection heating is 1.43 kW·h, with an average heat dissipation of 748.7 W. Regardless of power consumption or heat dissipation, convection heating is significantly higher than heat conduction heating, resulting in the room air temperature of the former increased from 12.3 °C to 17.3 °C, while the latter only increased from 14.4 °C to 15.2 °C. The study found that the water temperature of heat conduction heating can meet the thermal comfort needs of the human body in the range of 38~40 °C, while convection heating requires a higher temperature range, In contrast, the grade of hot water required for heat conduction heating is lower. Through the experiment, it is also found that the temperature of convection heating rises fast, but it is easy to appear dry feeling after a long time, while heat conductive heating has a slow temperature rise. there is a cool feeling within 20 min after the heating starts, and then the thermal comfort is better. The air conditioning system in this paper is used for the heating experiment in the winter lunch break mode, compared with convection heating, the overall thermal comfort of heat conduction heating is better and more energy efficient. it is suggested to adopt heat conduction heating mode in the winter heating of this system.

The integration of the increasing share of Renewable Energy Sources (RES) requires the availability of suitable energy storage systems to improve the grid flexibility, and Compressed Air Energy Storage (CAES) systems could be a promising option. In this study, a CO2-free Diabatic CAES system is proposed and analysed. The plant configuration is derived from a down-scaled version of the McIntosh diabatic CAES plant, where the natural gas is replaced with green hydrogen, produced on site by a Proton Exchange Membrane electrolyser powered by a Photovoltaic power plant. In this study, the components of the hydrogen production system are sized to maximize the Self-Consumption share of PV energy generation and the effect of the design parameters on the H2-CAES plant performance are analysed on a yearly basis. Moreover, a comparison between the use of natural gas and hydrogen in terms of energy consumption and CO2 emissions is discussed. The results show that the proposed hydrogen fuelled CAES can effectively match the generation profile and the yearly production of the natural gas fuelled plant by using all the PV energy production, while producing zero CO2 emissions.

The automotive industry is continuously seeking innovative solutions to improve the energy efficiency and sustainability of vehicles. Among the various energy-consuming systems in automobiles, air conditioning plays a crucial role. However, conventional vapour compression-based air conditioning systems are known for their high energy consumption and environmental impact. In recent years, adsorption technology has gained significant attention as a promising alternative due to its potential for higher energy efficiency and reduced greenhouse gas emissions. This review paper presents a comprehensive analysis of advancements in adsorption air conditioning technology specifically designed for automotive applications. The paper examines the recent research and development efforts in enhancing the performance and practicality of these systems, encompassing areas such as advanced materials selection, and system integration strategies. Furthermore, this review highlights the benefits and challenges associated with implementing adsorption air conditioning systems in vehicles. The environmental impact and potential for waste heat recovery are also discussed. Additionally, emerging trends, such as hybridization with conventional vapour compression systems, are explored to further optimize the energy efficiency and sustainability of automotive air conditioning. By critically evaluating the existing literature and research advancements, this review provides insights into the state-of-the-art thermally driven technologies for automotive applications.

Kombucha is a popular sparkling sugared tea, fermented by a symbiotic culture of acetic acid bacteria (AAB) and yeast. The demand for Kombucha is increasing worldwide mainly due to its perceived health benefits and appealing sensory properties. This study isolated and characterised the dominant AAB and yeast from starter culture and Kombucha broth after 0, 1, 3, 5, 7, 9, 11, and 14 days of fermentation at ambient temperature (~22°C). Changes in the microbial composition were associated with variations in the physico-chemical characteristics of Kombucha tea, such as pH, titratable acidity, and total soluble solids (TSS). During fermentation, the acidity increased, and TSS decreased. The yield, moisture content and water activity of the cellulosic pellicles which had developed by the end of fermentation were attributed to the presence of AAB. Yeast and AAB were isolated from the Kombucha samples using glucose yeast extract mannitol ethanol acetic acid (GYMEA) and yeast extract glucose chloramphenicol (YGC) media respectively, using serial dilutions. Phenotypic and taxonomic identification of AAB and yeast were determined by morphological and biochemical characterisation, followed by sequence analysis of the ribosomal RNA gene (16S rRNA for AAB and ITS for yeast). The dominant AAB species in the cellulosic pellicle and Kombucha broth was identified as Komagataeibacter rhaeticus. The yeast isolates belonged to Debaryomyces prosopidis and Zygosaccharomyces lentus.

Six bacterial strains with differing abilities to produce varying concentrations of Indole Acetic Acid were tested individually and in consortia for plant growth promoting and fitness related traits of Cicer arietinum. In all experiments the presence of the nitrogen fixer Mesorhizobium ciceri resulted in increased biomass production. In the absence of this strain, IAA Psedomonas putida and Bacillus megaterium hinder plant growth and fitness related traits. The application of mixes of the three strains always resulted in better plant performance when M. ciceri was present. Whereas P. putida has a noticeable plant growth-promoting effect B. megaterium resulted less effective. The low levels of IAA produced by the selected strains had a significantly greater positive effect on plant biomass accumulation, flower, pods and seed production as well as on total plant nitrogen and nitrogen concentration in seed than high IAA producer strains.

Although commercially-available low-cost air quality sensors have low accuracy, the sensor system are being used to collect the data for the regulation of PM2.5 emission caused by industrial activities or to estimate the personal exposure for PM2.5. In this work, to solve the accuracy problem of low-cost PM sensor, we developed a new PM2.5 calibration model by combining the deep neural network (DNN) optimized in calibration problem and a LSTM optimized in time-dependent characteristics. First, two datasets were generated to test the accuracy performance and generalization performance of the PM2.5 calibration machine learning (ML) model. The PM2.5 concentrations, temperature and humidity by low-cost sensor and gravimetric-based PM2.5 measuring instrument were sampled for a sufficiently long time. The proposed model was compared with benchmark (multiple linear regression model) and low-cost sensor results. For root mean square error (RMSE) for PM2.5 concentrations, the proposed model reduced 41-60% of error compared to the raw data of low-cost sensor, and reduced 30-51% of error compared to the benchmark model. R2 of ML model, MLR and raw data were 93, 80 and 59 %. Also, the developed model still showed consistent calibration performance when calibrated with new sensors in different locations. Low-cost sensors combined with ML model not only can improve the calibration performance of benchmark, but also can be applied to the sensor monitoring systems for various epidemiologic investigations and regulatory decisions.

Despite being stored at 113 K and atmospheric pressure, LNG cold potential is not exploited to reduce green ships’ energy needs. An innovative system based on three Organic Ranking Cycles integrated into the regasification equipment is proposed to produce additional power and recover cooling energy from condensers. A first-law analysis identified ethylene and ethane as suitable working fluids for the first and the second ORC making available freshwater and ice. Propane, ammonia and propylene could be arbitrarily employed in the third ORC for air-conditioning. An environmental analysis that combines exergy efficiency, ecological indices and hazard aspects for marine environment and ship’s passengers, indicated propylene as safer and more environmentally friendly. The exergy analysis confirms more than 20% of the LNG potential can be recovered from every cycle to produce a net clean power of 76 kW, whereas 270 kW can be saved by recovering condensers' cooling power to satisfy some ship needs. Assuming the sailing mode, a limitation of 162 kg in LNG consumptions was determined, avoiding the emission of 1584 kg of CO2 per day. Marine thermal pollution is reduced by 3.5 times by recovering the working fluids' condensation heat for the LNG pre-heating.

Abstract: Metal-air batteries provide a most promising battery technology given their outstanding potential energy densities, which are desirable for both stationary and mobile applications in a ‘beyond lithium-ion’ battery market. Silicon- and iron-air batteries underwent less research and development compared to lithium- and zinc-air batteries. Nevertheless, in the recent past, the two also-ran battery systems made considerable progress and attracted rising research interest due to the excellent resource-efficiency of silicon and iron. Silicon and iron are among the top five of the most abundant elements in the earth’s crust, which ensures almost infinite material supply of the anode materials, even for large scale applications. Furthermore, primary silicon-air batteries are set to provide one of the highest energy densities among all batteries, while iron-air batteries are frequently considered as a highly rechargeable system with decent performance characteristics. Considering fundamental aspects for the anode materials, i.e., the metal electrodes, in this review, we will first outline the challenges, which explicitly apply to silicon- and iron-air batteries and prevented them from a broad implementation so far. Afterwards, we provide an extensive literature survey regarding state-of-the-art experimental approaches, which are set to resolve the aforementioned challenges and might enable the introduction of silicon- and iron-air batteries into the battery market in the future.

Cadmium (Cd) is a heavy metal that suppresses plant growth; however, application of endophytic bacteria can increase resistance of plants against Cd, as well as improve plant growth. Two bacterial endophytic strains were isolated from Solanum nigrum and were identified as Serratia sp. AI001 and Enterobacter sp. AI002 by 16S DNA sequencing. Strains AI001 and AI002, tolerated up to 25 mg/mL Cd in broth culture and showed phosphate solubilization potential in Pikovskaya agar medium. AI001 and AI002 produced indole-3-acetic acid, which was confirmed by gas spectrometry-mass chromatography. Brassica plants stressed with 0, 5, 15, and 25 mg/L Cd showed significant decrease in plant growth, chlorophyll content and biomass, and significant increase in Cd dose-dependent electrolyte leakage. Inoculation of strain AI001 or AI002 significantly enhanced the plant growth attributes of shoot length, root length, chlorophyll content, and biomass as compared to those in uninoculated plants. Reduced glutathione contents in plants stressed with different concentrations of Cd also increased with inoculation of AI001 and AI002. The reason of Cd resistance enhancement in plants by inocula could be due to their greater plant growth promoting activities as well as their antioxidative response.

Hardened air void analysis provides essential information of concrete freeze-thaw durability based on the size and spacing of air voids in the material. As the physical freeze-thaw experiment is time-consuming and costly, the characteristics of concrete air voids are often deemed as a proxy of the freeze-thaw performance. This analysis is typically done by measuring the 2D air void intersections on polished samples, but the current interpretation of the 2D void characters does not accurately represent the actual void structure in 3D. To solve this problem, a 2D-to-3D unfolding technique has been proposed in the field of stereology. However, the unfolding analysis is known to be sensitive to several factors, such as void population and size along with a binning scheme, where improper unfolding can considerably bias the prediction of the actual concrete void system. This study investigates the optimal strategy of conducting the unfolding analysis for concrete. The investigation is carried out on both idealized void systems to interrogate the influence of the critical factors individually, and real concrete samples with varying levels of air entrainment to assess the concrete-specific impacts. The concrete void system is studied based on a stereological model emulating the intersected 3D air voids on the surface of polished concrete. The results highlight that, for unfolding concrete voids, logarithmic binning scheme is far more accurate to linear binning. The low unfolding error of the concrete samples indicates that the proposed methodology enables an accurate restoration of 3D void size distribution.

A review of desiccant dehumidification technologies for improving air-quality has been presented, especially focusing on alternatives for air conditioning systems for minimizing the Sick Building Syndrome. The principles and types of desiccant wheels, as well as the existing selection software for these types of equipment, were reviewed and comparatively evaluated. The study focuses on the Brazilian context, therefore, information about air condition systems and laws of this country were evaluated. Possible applications of desiccant wheels are also analyzed, such as their integration into cooling cycles and the sensible heat wheel. Finally, several commercial desiccant wheel selection software were evaluated, which are useful in many situations. Nevertheless, it was evidenced that the available softwares are not capable of performing an operation analysis for only a specific period. Therefore, it is essential to create computational tools to select desiccant wheels, considering the data from the different Brazilian regions for a year.

Most people living in Europe's cities are still exposed to levels of air pollution deemed harmful by the World Health Organization. In the modern world, air pollution is the foremost concern because of its impact in human health and economy. This strong connection appears gaining a lot of concern, driven by new installed low-cost electrochemical sensors monitoring systems. Highly accuracy, real-time monitoring, daily and yearly statistics, data access from experts or simple users, low-cost equipment and forecasting needs, enforce the market to develop new air quality monitoring systems using advanced technologies and protocols. In this study, a comparison via low-cost electrochemical sensors and of static, fixed site measurement monitoring station, is taking place in Athens, Greece, along with the data quality and Air Quality Index (AQI) including data accuracy and quality of data concerning adverse health effects due to air pollution. The findings presented in this work, relate to different flexible and affordable alternatives adopted during the evaluation and calibration of low-cost gas sensors for the monitoring. The significance of the positive results is particularly useful, especially considering the founding for interference, environmental conditions affections and air quality information including indexes and health recommendations for a specific location.

Mechanical ventilation systems, which are used for breathing support when a person is not able to do it by their own, requires a device for measuring the air flow to the patient in order to monitoring and a assure the magnitude establish by a medical staff. Flow sensors are the conventional devices used for the air flow measuring; however, there were not available in Peru, because of the international demand during COVID-19 pandemic. In this sense, a novel air flow sensor based on orifice plate and an intelligent transducer stage were developed as an integrated design. Advanced methodologies in simulations and experiments using specially designed equipment for this application were carried out. The obtained data was used for a mathematical characterization and dimensions validation of the integrated design. The device was tested in its real working conditions, it was implemented in a breathing circuit connected to a low-cost mechanical ventilation system based on cams. Results indicate that the designed air flow sensor/transducer is a low-cost complete medical device for mechanical ventilators able to provide satisfactorily all the ventilation parameters air flow, pressure and volume over time by measuring the air flow and calculating the others. Furthermore, this device provides directly a filtered equivalent electrical signal for a display or a computer.

Fine aroma cocoa (Theobroma cacao) is one of Ecuador's most iconic export products, representing 63% of world production; however, few advances have been made in fermentation processes that greatly influence the development of chocolate´s organoleptic characteristics. The study of starter cultures has been investigated in other countries, which seek to improve organoleptic properties or decrease fermentation time. The aim of this study was to analyze the effect of a native microbial consortium based on two yeasts (Torulaspora delbrueckii and Hanseniaspora uvarum), a lactic acid bacterium (LAB) (Lactobacillus plantarum) and an acetic acid bacterium (AAB) (Acetobacter ghanensis) inoculated at the beginning of the fermentative process, on physical and biochemical variables, microbial population dynamics, and percentage of almond fermentation. The started culture caused changes in sugar and acid content, which in turn generated temperature and pH changes in the dough, resulting in the dynamics of yeast, AAB, and mesophilic microorganisms remaining higher than those of the control throughout the fermentation process; a decrease of filamentous fungi that affect the flavor and quality of beans due to the production of acetic acid or secondary metabolites from yeasts and LAB; and optimized fermentation percentage by 24% higher than spontaneous fermentation in only 96 hours.

Research results of the relationships between air-volume in air-entrained cement paste, mortar and concrete, all designed according to PN-EN 480-1 guidelines are presented in the paper. The cement paste, mortar and concrete, with w/c=0,5 ratio, were prepared using innovative air-entraining cement CEM II/B-V. The air-entraining cement CEM II/B-V was produced using two methods: mixed together with natural or synthetic aerated admixture. The air volume test of the volumetric method was carried out in case of fresh cement paste, mortar and concrete mix. Fresh concretes were evaluated in terms of stability of air entrainment and consistency for 5, 20 and 40 min. The porosity structure parameters, like summarized air-content, specific surface of air voids, air-voids spacing factor and micropores content of hardened concrete, were estimated using computed tomography with a resolution of 2-5 μm. The aim of the research was to determine the dependence between air-content of cement paste, mortar and concrete on the measurement of air-entrainment of cement paste or mortar with the same w/c ratio and type of cement, all designed according to PN-EN 480-1 guidelines. Test results proved that there is a good correlation between the measured air-content of the cement paste, mortar and concrete. Therefore, it is possible to predict the aeration of concrete on the air-entrainment of the mortar.

The aspirated hypersonic air-breathing propulsion system requires a large amount of power generation, but its special structure makes it impossible to adopt common power generation methods. The high-temperature gaseous hydrocarbon fuel thermal power generation (TPG) system was developed to solve the power generation problem for hypersonic air-breathing propulsion system. But off-design operating conditions of the hypersonic propulsion system results in a more complex process for both propulsion system and the TPG system. To better analyzing the dynamic thermos-physical characteristics of hypersonic airbreathing propulsion system considering thermal-mechanical coupling process among cooling/TPG system, a dynamic analytical model was developed, and the dynamic thermos-physical characteristics of TPG system under different off-design working conditions were conducted. It can be concluded from the analytical results that the dynamic process of thermos-physical characteristics shows a complex trend under the flight Mach number and fuel equivalence ratio off-design working conditions. Such complexity of dynamic characteristics brings difficulties in fuel supply for the propulsion system.

Air traffic congestion is caused by the unbalance between increasing traffic demand and saturating capacity. Flight delay not only causes huge economical lost, but also has very negative environmental impact in the whole air transportation system. In order to identify the impact of extended TMA on airport capacity, an airspace capacity assessment method based on augmented cell transmission model was proposed. Firstly, the airspace structure was modeled with points, segments, layers, and cells. Secondly, mixed integer linear programming model was built up with maximum throughput or capacity as the objective function. Finally, genetic algorithm was used to find the optimal result, and the results were validated by comparing with the fast-time simulation results generated by total airspace and airport modeler (TAAM) software. It is found that the proposed method could achieve a relatively accurate result in a much affordable and fast way. The numerical results could be very helpful for air traffic controllers to analyze the dynamic traffic flow entering and exiting TMA, so as to make decisions via reasonable analysis and do planning in advance by referring to the airport capacity.

The coronavirus disease (COVID-19) pandemic caused by spreading rapidly a severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) has imposed a unique situation for the humanity. Sao Paulo has reported 124,105 confirmed cases of COVID-19 and 5,623 deaths up to June 14th, being considered the epicenter of the pandemic in Brazil and in South America. Due to the measures for social distancing, there was a drop in the air pollution concentration in Sao Paulo. Starting on March 16th, 2020, we broke 90 days of social distancing into 13 weeks and compared to an equivalent period in 2019. We investigated the air quality improvement during the quarantine period and compared the associated avoided deaths to COVID-19 burden deaths. Nitrogen dioxide (NO₂) was the best indicator of air quality in the analyzed weeks, since its reduction reached 58 %. Our study showed that the 5,623 deaths occurred during the analyzed weeks of quarantine represents an economic health loss of US$ 10.5 billion. In opposite, we observed a significant air quality improvement due to pollutants concentrations’ reductions during the analyzed weeks. Considering PM₁₀, PM_2.5 and NO₂, the decrease of concentration levels respectively avoided 78, 337 and 387 premature deaths and prevented up to US$ 1.5 billion on health costs. These results highlight the importance of continuing to enforce existing air pollution regulations and measures to protect human health both during and after COVID-19 pandemic.

The leaves and stems of Bauhinia guianensis Aubl. are used in traditional Amazonian phytotherapy for the treatment of pain and inflammation. This study investigates the anti-inflammatory and antinociceptive effects of hydroethanolic extracts from B. guianensis Aubl. leaves and stems (HELBg and HESBg, respectively) in in vivo models of inflammation and hyperalgesia. Danio rerio experimental animals were submitted to the acute inflammation test, induced by intraperitoneal (ip.) administration of carrageenan 20 μg / animal (abdominal edema), the groups were previously treated orally with saline solution 2 μl / animal (SS), Dimethyl sulfoxide 2 μl / animal (DMSO), Indomethacin 10 mg/kg, HELBg 100 mg/kg and HESBg 100 mg/kg, n = 12 per experimental group, to evaluate inhibition of edema and alterations histopathology of the liver, intestine and kidney of these animals. The antinociceptive effect was observed from the body curvature index and the behavioral responses of Danio rerio, after an experimental protocol for the induction of hyperalgesia, by ip. administration of 10 μl / animal of 2.5% acetic acid, the animals were previously orally treated with saline solution 2 μl/animal (SS), dimethyl sulfoxide 2 μl/animal (DMSO), morphine 2.5 mg/kg, HELBg 100 mg/kg and HESBg 100 mg/kg, n = 5 per experimental group. In carrageenan-induced edema, the group treated with HESBg inhibited edema formation over the 3 hours of the experiment. Maximum edema was inhibited by 54% (p < 0.05) when compared to the control group. Both HELBg and HESBg prevented body curvature index changes (t (df = 3 8) =, 6.96 and t (df = 3, 8) = 6.61, respectively, both p < 0.0001). In the behavioral parameters sensitive to antinociceptive pharmacological modulation, due to the abdominal constriction induced by acetic acid, the administration of HELBg and HESBg resulted in an improvement in swimming activity, by increasing the distance covered (F (df = 3, 16) = 6.50 and F (df = 3, 16)  = 7.72, respectively, both p < 0.0001), decrease in freezing time (F (df = 3, 16)  = 2.04 and F (df = 3, 16)  = 1.28, respectively, both p < 0.0059), increase in the number of ascents to the upper area of the tank (F (df = 3, 16)  = 33.02 and F (df = 3, 16)  = 35.62, respectively, both p < 0.0009 ) and decreased time spent in that area (F (df = 3, 16)  = 101.19 and F (df = 3, 16)  = 103.59, respectively, both p < 0.0038). It is reasonable to suppose that both extracts modulated the variations induced by carrageenan and acetic acid through the inhibition of prostaglandin biosynthesis, decreasing the release of inflammatory mediators and the sensitization of peripheral nociceptors and, consequently, the perception of pain. These results suggest that HELBg and HESBg have anti-inflammatory and antinociceptive activities, probably of peripheral origin and linked to the inhibition of prostaglandin biosynthesis.

The leaves and stems of Bauhinia guianensis Aubl. are used in traditional Amazonian phytotherapy for the treatment of pain and inflammation. This study investigates the anti-inflammatory and antinociceptive effects of hydroethanolic extracts from B. guianensis Aubl. leaves and stems (HELBg and HESBg, respectively) in in vivo models of inflammation and hyperalgesia. Danio rerio experimental animals were submitted to the acute inflammation test, induced by intraperitoneal (ip.) administration of carrageenan 20 μg / animal (abdominal edema), the groups were previously treated orally with saline solution 2 μl / animal (SS), Dimethyl sulfoxide 2 μl / animal (DMSO), Indomethacin 10 mg/Kg, HELBg 100 mg/Kg and HESBg 100 mg/Kg, n = 12 per experimental group, to evaluate inhibition of edema and alterations histopathology of the liver, intestine and kidney of these animals. The antinociceptive effect was observed from the body curvature index and the behavioral responses of Danio rerio, after an experimental protocol for the induction of hyperalgesia, by ip administration. of 10 μl / animal of 2.5% acetic acid, the animals were previously orally treated with saline solution 2 μl/animal (SS), dimethyl sulfoxide 2 μl/animal (DMSO), morphine 2.5 mg/Kg, HELBg 100 mg/Kg and HESBg 100 mg/Kg, n = 5 per experimental group. In carrageenan-induced edema, the group treated with HESBg inhibited edema formation over the 3 hours of the experiment. Maximum edema was inhibited by 54% (p < 0.05) when compared to the control group. Both HELBg and HESBg prevented body curvature index changes (t (df = 3 8) =, 6.96 and t (df = 3, 8) = 6.61, respectively, both p < 0.0001). In the behavioral parameters sensitive to antinociceptive pharmacological modulation, due to the abdominal constriction induced by acetic acid, the administration of HELBg and HESBg resulted in an improvement in swimming activity, by increasing the distance covered (F (df = 3, 16) = 6.50 and F (df = 3, 16)  = 7.72, respectively, both p < 0.0001), decrease in freezing time (F (df = 3, 16)  = 2.04 and F (df = 3, 16)  = 1.28, respectively, both p < 0.0059), increase in the number of ascents to the upper area of the tank (F (df = 3, 16)  = 33.02 and F (df = 3, 16)  = 35.62, respectively, both p < 0.0009 ) and decreased time spent in that area (F (df = 3, 16)  = 101.19 and F (df = 3, 16)  = 103.59, respectively, both p < 0.0038). It is reasonable to suppose that both extracts modulated the variations induced by carrageenan and acetic acid through the inhibition of prostaglandin biosynthesis, decreasing the release of inflammatory mediators and the sensitization of peripheral nociceptors and, consequently, the perception of pain. These results suggest that HELBg and HESBg have anti-inflammatory and antinociceptive activities, probably of peripheral origin and linked to the inhibition of prosta-glandin biosynthesis

Recently, the Integrated Air Defense System (IADS) has become vital for the defense system as the military defense system is vital for national security. Placing Integrated Air Defense System batteries among locations to protect locations assets is a crucial problem because optimal solutions are needed for interceptor missiles to intercept attacker missiles for maximizing protection of assets across locations or places. In this research, the procedures of using network algorithms along with developing several network algorithms are going to be demonstrated to develop a model for sequential development of seven network securing strategies of placing Surface to Air Missile (SAM) batteries to maximize the protection of assets across locations (based on given asset values) by generating optimal solutions through computation to destroy maximum attacker missiles by using minimum interceptor missiles with given intercept probability. This network securing strategies can be implemented not only for Integrated Air Defense System (IADS) planning but also Counter Air (CA) planning as Integrated Air Defense System (IADS) is conducted with defensive counter air supported by attack operations in offensive counter air.

Environment pollution is the major problem for all the sectors. In environment pollution there are different types of pollution is included such as air pollution, water pollution, soil pollution etc. In these types of pollution most of it is air pollution. There are many reasons for pollution of air. Human advance in science but one of the major draw backs of science is the pollution of air rapidly. Air pollution is injurious to health. Every year a large number of people died for the effects of air pollution. It can be improved in many ways among these ways technology upgradation plays a major role here. There are various method that prevent air pollution. Many researchers tried and is trying to prevent the air pollution in many ways. In this review paper I summarise the existing research on different ways for preventing air pollution in addition I will discuss the gaps and future aspect on this topic.

Purpose: This study aimed to focus on the design and development of low-cost DIY air purifiers, using a ventilating fan, air pump, water pump, and an ultrasonic generator, with regard to filtration efficacy and also cost-effectiveness that can be used during the COVID-19 pandemic and haze pollution. Methods: Six types of household air purifiers, incorporating a HEPA filter, a HEPA filter & electrostatic fiber, an air pump, an air pump & ultrasonic wave, a water pump, and a water pump & ultrasonic wave, were fabricated. The amount of particulate matter (PM) and CO₂ levels were recorded at 0, 10, 20, 30, and 60 min, then, repeated 3 times. After 10 min of the 3^rd experiment of each study, the last measurement of air pollution would be recorded. Results: At 60 min, the HEPA filter & electrostatic fiber showed the best performance regarding reduction of PM and CO₂ levels. The highest PM reduction rate had occurred at 30 min using an air pump procedure (99.330 to 100%). The CO₂ levels of all experiments had fluctuated at different times. After 10 min of a closed machine, HEPA filter & electrostatic fiber revealed the highest rate of PM elevation, while PM levels of all water-based purifier systems were decreased. A water pump and air pump were the cheapest air cleaners, when taking into account maintenance expenses and electricity charges. Conclusion: An air pump is the optimum method for reducing particulate matter at minimum cost but without the benefit of reduced humidity, while the HEPA filter & electrostatic fiber is the best system to decrease PM levels, but this requires an enclosed structure at the inlet to prevent dust coming back into the room. As filtration efficiency is increased by the use of filters & electrostatic fiber mechanisms, the more expensive the system becomes.

The rural communities are affected by gaseous emissions from intensive livestock production. Practical mitigation technologies are needed to minimize emissions from stored manure and improve air quality inside barns. In our previous research, the one-time surficial application of biochar to swine manure significantly reduced emissions of NH3 and phenol. We observed that the mitigation effect decreased with time during the 30-day trials. In this research, we hypothe-sized that bi-weekly reapplication of biochar could improve the mitigation effect on a wider range of odorous compounds using larger scale and longer trials. The objective was to evaluate the effectiveness of biochar dose and reapplication on mitigation of targeted gases (NH3, odor-ous VOCs, odor, GHGs) from stored swine manure on a pilot-scale setup over 8-weeks. The bi-weekly reapplication of the lower biochar dose (2 kg/m2) showed much higher significant percent reductions of emissions for NH3 (33% without & 53% with reapplication) and skatole (42% without & 80% with reapplication), respectively. In addition, the reapplication resulted in the emergence of statistical significance to the mitigation effect for all other targeted VOCs. Spe-cifically, for indole, the % reduction improved from 38% (p=0.47, without reapplication) to 78% (p=0.018, with reapplication). For phenol, the % reduction improved from 28% (p=0.71, without reapplication) to 89% (p=0.005, with reapplication). For p-cresol, the % reduction improved from 31% (p=0.86, without reapplication) to 74% (p=0.028, with reapplication). For 4-ethyl phenol, the percent emissions reduction improved from 66% (p=0.44, without reapplication) to 87% (p=0.007, with reapplication). The one-time 2 kg/m2 and 4 kg/m2 treatments showed similar effectiveness in mitigating all targeted gases, and no statistical difference was found between the dosages. The one-time treatments showed significant % reductions of 33% & 42% and 25% & 48% for NH3 and skatole, respectively. The practical significance is that the higher (one-time) biochar dose may not necessarily result in improved performance over the 8-week manure storage, but the bi-weekly reapplication showed significant improvement in mitigating NH3 and odorous VOCs. The lower dosages and the frequency of reapplication on the larger-scale should be explored to optimize biochar treatment and bring it closer to on-farm trials.

The physical environment plays an important role in the transmission of respiratory infections like Covid-19. To find relevant articles on environmental factors influencing respiratory infection outbreaks, we searched Pub med Central on the following topics: 1. Environmental pollution causing coronavirus fatality- 73 results, relevant 1 article, 2. Environmental factors affecting Covid-19, 149 results from which there were 6 relevant articles, 3. Impact of air pollution on Covid-19 fatality, 10 results, relevant 3 articles, 4. Environmental factors affecting respiratory viruses- 10646 results were obtained, 2 relevant articles. We searched Google scholar on environmental factors affecting Covid-19 transmission and found 7 relevant papers. We excluded the duplicates in each of the key words search. Date of search was on 20^th April 2020. All articles included in results were scrutinized and relevance of articles was based on their content that discussed meteorological and physical environment factors in the spread and severity of Covid-19. We have discussed factors like air pollution, smoking, air temperature, humidity and air velocity as contributing factors. If meteorological factors are conducive to spread in a particular area, we need protective measures way before a respiratory infection outbreak occurs. Covid-19 is a lesson learnt the hard way, and we must enable people to practice hygienic practices with limited resources but high level of protection that it provides. Air pollution control can prevent priming of respiratory system which shall further protect from pulmonary infections.

Shenzhen is China’s top ten clean air city and the cleanest air megacity. Even so, epidemiologic studies have shown ambient air pollution had significant adverse impacts on human health in this less polluted city. In this study, the concentrations of six criteria air pollutants (PM2.5, PM10, O3, NO2, SO2, and CO) from 2014 to 2017 were analyzed and compared to thresholds of both national and international air quality standards. The results showed concentrations of all air pollutants were below target values of current national air quality standard, but levels of particulate matter (PM) and O3 were still much higher than the recommended levels by the World Health Organization. Within national air quality standards, the number of over-limit days was rare with few variations between highly polluted and low pollution areas. The air quality improvement was slowing down recently. Our results suggest annual and daily thresholds for PM are too loose for air quality improvement in Shenzhen. Hence, we call for evaluation and establishment of tougher air quality standard.

Distracted driving is the leading cause of accidents, the cause of these distractions may include drowsiness, using cell phone, smoking a cigarette, etc. The proposed paper aims at monitoring the attentiveness of the driver and alerting the driver when his/her alertness goes below a certain threshold. It uses image processing using OpenCV (Computer Vision) and You Look Only Once (YOLO) algorithm to detect the eyes and object respectively and sounds an alarm when the driver is either drowsy or using his cell phone or smoking a cigarette.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

In this study, a carbon fiber microelectrode (CF) was applied for the investigation of electrochemical behavior and determination of natural antioxidant, apocynin (APO). Given the limited solubility of APO in water, a mixture of anhydrous acetic acid (AcH) with 20%, v/v acetonitrile (AN) and 0.1 mol L-1 sodium acetate (AcNa) was used. The electrochemical properties of APO were examined through linear sweep voltammetry (LSV), differential pulse voltammetry (DPV), and cyclic voltammetry (CV). The anodic oxidation of APO, which is the basis of the method used, proved to be diffusion-controlled and proceeded with a two-electron and one proton exchange. Both radicals and radical cations, arising from the first and second step of electrode reactions, respectively, underwent subsequent chemical transformations to yield more stable final products (EqCiEiCi mechanism). Using optimized DPV conditions, the anodic peak current of APO at potential of 0.925 V vs Ag/AgCl showed a good linear response within the concentration range of 2.7×10-6 – 2.6×10-4 mol L-1. The detection and quantification limits were determined as 8.9×10-7 and 2.7×10-6 mol L-1, respectively. The developed DPV method enabled the successful determination of APO in herbal extracts and in dietary supplements. It should be noted that this is the first method of voltammetric determination of APO.

Synthesis of a novel series of chromen-3-yl-pyridine moieties. IR, NMR, and MS spectroscopy were used to confirm the structure of these novel compounds and study of antitumor activity of these compounds. The structure activity relationship investigation demonstrated that 2,4-diamino-5-(3-methoxyphenyl)-7-(2-oxo-2H-chromen-3-yl)-1,8-naphthyridine-3-carbonitrile (16), was more effective and naphthyridine-3-carbonitrile derivatives 17, 18 and pyrido[2,3-d]pyrimidine derivative 12, while compounds 5a,b, 9c, 11, 13 and 14 were moderate activity for antitumor activities.

This work aims to investigate systematically the influence of process temperature, bio-mass-to-water ratio, and production scales (laboratory and pilot) on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale, as well as at 200, 225, and 250 °C, 2 °C/min, bio-mass-to-water ratio of 1:10, in laboratory scale. The elemental composition (C, H, N, S) of solid phase determined to compute the HHV. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas an-alyzer. For the experiments in pilot scale with constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential de-cay with temperature, while that of liquid and gaseous phases a smooth growth. By varying the biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied be-tween 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with increasing temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total car-boxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentra-tions of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfu-ral, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio. For the experiments in laboratory scale with constant biomass-to-water ratio of 1:10, the yields of solid ranged between 55.9 and 51.1% (wt.), showing not only a linear decay with tem-perature, but also a lower degradation grade. The chemical composition of main organic compounds (furfu-ral, HMF, phenols, cathecol, and acetic acid) dissolved in the aqueous phase in laboratory scale shows the same behavior of those in obtained in pilot scale.

This work aims to investigate systematically the influence of process temperature and biomass-to-water ration on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas analyzer. For constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential decay with temperature, while that of liquid and gaseous phases a smooth growth. By variation of biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied between 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total carboxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentrations of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfural, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio.

Abstract: This article explores the intricate relationship between environmental degradation, specifically air pollution, and economic growth in the Sultanate of Oman spanning the period from 1990 to 2022. We employ cointegration and vector error correction models to uncover both short- and long-term dynamics in the association between air pollution and economic growth. Fur-thermore, Granger causality analysis is utilized to investigate the causal links between these crucial variables. This data encompasses factors related to environmental quality and various control variables. The empirical results unveil a sustained long-term cointegration connection between the variables. Additionally, our findings highlight a statistically significant positive impact of economic growth and energy consumption on CO2 emissions. Furthermore, the short-term analysis reveals an annual adjustment of approximately 14.1% in N2O emissions dis-equilibrium. The Granger causality study indicates unidirectional causal relationships involving N2O emissions, economic growth, and CO2 emissions. The implications of these findings for Oman's policy landscape are substantial. To effectively reduce greenhouse gas emissions, it is imperative for Oman to establish robust climate change policies. Additionally, the government can play a pivotal role in encouraging and endorsing the use of renewable energy sources, such as green hydrogen, as a promising alternative to traditional oil and gas resources.

As the haze engulfed the Delhi NCR after Diwali there is a panic in public about its causes and consequences. Here are some facts and figures to know the truth behind the scene. Temperature fell down from 24’C on October 31 to 21’C on November 2 as recorded at UPPCB station at sector-125, Noida which is adjacent to Delhi a very strategic location and can be considered as reference point for Delhi-NCR. The details of the study conducted is given below.

This publication aims to disseminate a step-by-step process that walks through the conceptualization and building of a low-cost (~ $150 monitoring device for airborne fine particulate matter (PM2.5), based on miniaturized sensors and components. Details on the implementation of the hardware and software are provided which facilitate the data acquisition, capture and analysis. The central components and their setup discussed in what follows include: the sensor device (called “P.ALP” – Ph.D. Air quality Low-cost Project), Arduino IDE (Integrated Development Environment) and R code (open-access software). A monitoring device for PM2.5, using low-cost sensors and technologies was successfully conceptualized, designed, and implemented. The P.ALP monitoring system was designed and developed to be a basic device, which can be further customized and implemented using the wide range of low-cost sensors available on the market.

Elevated indoor CO2 levels might have adverse effects on human health. However, the introduction of outdoor air to lower indoor CO2 concentrations results in significant HVAC energy consumption. Aligning with office hours and the natural light cycle, the utilization of photosynthesis in living walls offers an energy-efficient and sustainable solution for the mitigation of high CO2 levels in office spaces. This study experimentally investigates the impacts of the carbon fixation pathways, light intensity, and substrate moisture content on the CO2 removal rate of living walls at the room scale. Furthermore, the fresh air energy-saving effects of living walls under different scenarios are accurately simulated in EnergyPlus. The results demonstrate that choosing C3 plants over CAM plants in living walls yields higher CO2 removal efficiency. In a 30-m2 office room accommodating 2-3 occupants, living walls can reduce the demand for fresh air by 12.3%-27.8% and decrease fresh air energy consumption by 11.2%-28.2%. The city with the highest energy savings has energy savings that are 4.5 times greater than those of the city with the lowest energy savings. The findings of this research promote the application and development of living walls, thus providing a viable solution for improving indoor air quality.

This case study investigates the effects of ventilation intervention on measured and perceived indoor air quality (IAQ) in a repaired school where occupants reported IAQ problems. Occupants´ symptoms were suspected to be related to the impurities leaked indoors through the building envelope. The study’s aim was to determine whether a positive pressure of 5-7 Pa prevents the infiltration of harmful chemical and microbiological agents from structures, thus decreasing symptoms and discomfort. Ventilation intervention was conducted in a building section comprising 12 classrooms and was completed with IAQ measurements and occupants´ questionnaires. After intervention, the concentration of total volatile organic compounds (TVOC) and fine particulate matter (PM_2.5) decreased, and occupants´ negative perceptions became more moderate compared to those for other parts of the building. The indoor mycobiota differed in species composition from the outdoor mycobiota, and changed remarkably with the intervention, indicating that some species may have emanated from an indoor source before the intervention.

Marine cold air outbreaks (MCAOs) are large-scale events in which cold air masses are advected over open ocean. It is well-known that these events are linked to the formation of polar lows and other mesoscale phenomena associated with high wind speeds, and that they therefore in some cases represent a hazard to maritime activities. However, it is still unknown whether MCAOs are generally conducive to higher wind speeds than normal. Here this is investigated by comparing ocean near-surface wind speeds during MCAOs in atmospheric reanalysis products with different horizontal grid spacings, along with two case studies using a convection-permitting numerical weather prediction model. The study regions are the Labrador Sea and the Greenland–Iceland–Norwegian (GIN) Seas, where MCAOs have been shown to be important for air–sea interaction and deep water formation. One of the main findings is that wind speeds during the strongest MCAO events are higher than normal and higher than wind speeds during less severe events. Limited evidence from the case studies suggests that reanalyses with grid spacings of more than 50 km underestimate winds driven by the large ocean–atmosphere energy fluxes during MCAOs. The peak times of MCAO usually occur when baroclinic waves pass over the regions. Therefore, the strong wind episodes during MCAOs generally last for just a few days. However, MCAOs can persist for 50 days or more.

Exploring effective oxygen reduction reaction (ORR) electrocatalysts is crucial for progress in solid-state alkaline zinc-air batteries (ZAB). In this paper, silver-manganese dioxide-carbon nanotubes (SMC) ternary composites, which function as Electrocatalyst for air Electrodes, was produced via the pyrolysis of silver permanganate under microwave irradiation in one step. A scanning electron microscope (SEM), X-ray diffraction (XRD), and an energy dispersion spectrometer (EDS) have consistently determined that SMC consists of silver and alpha-manganese dioxide, which anchored on the surface of CNTs. Through polarization and chronoamperometery curves, the electrocatalytic activity of SMC for ORR was examined. The results reveal that SMC has higher catalytic activity than the chemically produced electrocatalyst for ORR in alkaline condition. Finally, a solid-state zinc-air cell with an electrocatalyst was constructed and tested. Constant current discharge curve of the zinc-air cell with SMC has a long discharge voltage plateau and a 60.03 mAh capacity at 30 mA · cm−2 . The mechanism of improvement in electrocatalytic activity was also discussed. In a summary, the strategy described in this study and the electrocatalyst produced can be regarded as an effective method for making a robust oxygen reduction catalyst toward solid-state zinc-air batteries.

Air corridors are an integral part of the advanced air mobility infrastructure. They are the virtual highways in the sky for transportation of people and cargo in the controlled airspace at an altitude of around 1000 ft. to 2000 ft. above the ground level. This paper presents fundamental insights into the design of air corridors with high operational efficiency as well as zero collisions. It begins with the definitions of air cube, skylane or track, intersection, vertiport, gate, and air corridor. Then, a multi-layered air corridor model is proposed. Traffic at intersections is analyzed in detail with examples of vehicles turning in different directions. The concept of capacity of an air corridor is introduced along with the nature of distribution of locations of vehicles in the air corridor and collision probability inside the corridor are discussed. Finally, the results of simulations of traffic flows are presented.

Air pollution is responsible for any adverse effects on human beings. Thermal discomfort, on the other hand, is able to overload the human body and eventually provoke health implications due to the heat imbalance. Methods: The aim of the present work is to study the behavior of two bio-climatic indexes and statistical characteristics of the air quality index for Sofia city - the capital of Bulgaria for the period 2008 - 2014. The study is based on WRF-CMAQ model system simula-tions with a spatial resolution of 1 kilometer. The air quality is estimated by the air quality index, taking into account the influence of different pollutants and the thermal conditions by two indi-ces, respectively, for hot and cold weather. Results: It was found that half of the heat and cold index categories are present in the simulations. Their distribution has some spatial features. All air quality categories are present in the domain, with dominance only of the O3 and PM10. Conclu-sions: It was found that Sofia is not so hot and air polluted place, but in some situations, people have to have some concerns when intend to be outdoors for a prolonged time.

The building sector is the largest consumer of energy and there are still major scientific challenges in this field. The façade, being the interface between the exterior and interior space, plays a key role in the energy efficiency of a building. In this context, this paper focuses on a ventilated bioclimatic wall for NZEB zero energy buildings. The objective of this study is to investigate an experimental set-up based on a Hot Box allowing characterizing the thermal performances of the ventilated wall. A specific ventilated prototype and an original thermal metrology has been developed. This paper presents the ventilated prototype, the experimental set-up and experimental results on the thermal performances of the ventilated wall. The influence of the air space thickness and the air flow rate on the thermal performances of the ventilated wall is studied.

Livestock production systems generate nuisance odor and gaseous emissions affecting local communities and regional air quality. Also, there are concerns about the occupational health and safety of farm workers. Proven mitigation technologies that are consistent with the socio-economic challenges of animal farming are needed. We have been scaling up the photocatalytic treatment of emissions from lab-scale, aiming at farm-scale readiness. In this paper, we present the design, testing, and commissioning of a mobile laboratory for on-farm research and demonstration of performance in real farm conditions. The mobile lab is capable of treating up to 1.2 m3·s-1 of air with TiO2-based photocatalysis and adjustable UV-A dose based on LED lamps. We summarize the main technical requirements, constraints, approach, and performance metrics for the mobile laboratory, such as the effectiveness (measured as the percent reduction) and cost of photocatalytic treatment of air. The commissioning of all systems with standard gases resulted in ~9% and 34% reduction of NH3 and butan-1-ol, respectively. We demonstrated that as the percent reduction of standard gases increased with increased light intensity and treatment time. These results show that the mobile laboratory was ready for on-farm deployment and evaluating the effectiveness of UV treatment.

In the pursuit of energy efficiency and reduced environmental impact, adequate ventilation in enclosed spaces is essential. This study presents a hybrid neural network model designed for real-time monitoring and prediction of environmental variables. The system comprises two phases: An IoT hardware-software platform for data acquisition and decision-making, and a hybrid model combining short-term memory and convolutional recurrent structures. The results are promising and hold potential for integration into parallel processing AI architectures.

Human factors are the things that go wrong in the interactions between a team of people and a system of technology. This is part of a broader transdisciplinary field called engineering psychology, which as the name suggests, draws from both engineering and psychology. Many, if not most, catastrophic accidents involve a socio-technical interaction, i.e. are not solely due to technology failure. Hence, there is a need to consider human factors in the development or deployment of any technical system. This article is about the human factors involved in an aviation accident in New Zealand between a Yak and a cherry picker. The types of human error are identified, and the barrier bowtie method is used to represent them. The analysis gives different insights into the accident compared to the formal accident report, and better represents the human error characteristics.

Endophytic fungi colonize the inner tissues of plants and provide direct and indirect benefits to the plant. Although Mongolia is rich in medicinal plants, due to climatic and anthropogenic reasons the resources are being depleted and many species are under the threat of gradual extinction, while the endophytic fungi of Mongolian plants are largely unknown. Understanding the diversity and metabolic potential of endophytic fungi is of great significance in terms of the utilization of beneficial fungal strains in plant propagation and the discovery of bioactive compounds. In this study, a total of 24 culturable endophytic fungal strains were isolated from Cynomorium songaricum (Rupr.), a medicinal and vulnerable plant species of Mongolia. Based on the morphological characteristics and the sequences of the rDNA internal transcribed spacer (ITS) region, the isolates were identified to 6 genera: Fusarium (8), Clonostachys (7), Penicillium (6), Alternaria (1), Aspergillus (1), and Madurella (1). The antimicrobial activity was assessed by agar-diffusion method, revealing that 15 strains were able to inhibit the growth of at least one of the test organisms. Among them, 1 strain showed inhibitory activity against Escherichia coli, 12 against Bacillus subtilis, 13 against Staphylococcus aureus, 8 against Aspergillus niger, respectively. All fungal strains were screened for their ability to solubilize complex phosphorus and zinc minerals and for their production of indole-3-acetic acid (IAA). The strains were preserved in the national culture collection for further sustainable exploitation of their biotechnological potential.

(1) Background: Environmental and public health research has given considerable attention to the impact of air quality on brain health, with systematic reviews widespread. No literature review has been done for cognitive frailty – a multidimensional syndrome combining physical frailty and cognitive impairment and their apparent co-dependence, linked to increased vulnerability and adverse health outcomes, including dementia. Instead, cognitive decline and frailty is implicitly explored through research on air quality and comorbid cognitive and physical decline in elderly populations. (2) Methods: A scoping review was conducted to explore the need for a systematic review. Combining Arksey and O’Malley [1] and PRISMA-ScR checklist [2], a scoping review of SCOPUS using ‘cogniti*’ + ‘resilience’ + ‘air quality’ or ‘cogniti*’ + ‘ageing’ + ‘air quality’ resulted in N=2503 articles, screened and reduced using inclusion and exclusion criteria, to N=16 articles. (3) Results: Air quality appears to be a critical risk factor for cognitive decline, even at air quality levels below WHO targets. Moderate long-term ambient air pollution appears linked to increased risk of cognitive frailty, suggesting earlier and more active interventions to protect older people. There are varied effects on cognition across the life course, with both emotional and functional impacts. Effects may be more detrimental to elderly people with existing conditions, including economic and health inequalities. Generalisation of results is limited due to the absence of a dose-response, variations in methods, controlling for comorbid effects, and variance across studies. (4) Conclusions: The findings support the need for more research and a more extensive summary of the literature.

It is essential to mitigate gaseous emissions that result from poultry and livestock production to increase industry sustainability. Odorous volatile organic compounds (VOCs), ammonia (NH3), hydrogen sulfide (H2S), and greenhouse gases (GHGs) have detrimental effects on the quality of life in rural communities, the environment, and climate. This study's objective was to evaluate the photocatalytic UV treatment of gaseous emissions of odor, odorous VOCs, NH3, and other gases (GHGs, O3 – sometimes considered as by-products of UV treatment) from stored swine manure on a pilot-scale. The manure emissions were treated in fast-moving air using a mobile lab equipped with UV-A and UV-C lights and TiO2-based photocatalyst. Treated gas airflow (0.25 to 0.76 m3/s) simulates output from a small ventilation fan in a barn. Through controlling the light intensity and airflow, UV dose was tested for techno-economic analyses. The treatment effectiveness depended on the UV dose and wavelength. Under UV-A (367 nm) photocatalysis, the percent reduction of targeted gases was up to i) 63% of odor, ii) 51%, 51%, 53%, 67%, and 32% of acetic acid, propanoic acid, butanoic acid, p-cresol, and indole, respectively, iii) 14% of nitrous oxide (N2O), iv) 100% of O3, and 26% generation of CO2. Under UV-C (185+254 nm) photocatalysis, the percent reductions of target gases were up to i) 54% and 47% for p-cresol and indole, respectively, ii) 25% of N2O, iii) 71% of CH4, and 46% & 139% generation of CO2 & O3, respectively. The results proved that the UV technology was sufficiently effective in treating odorous gases, and the mobile lab was ready for farm-scale trials. The UV technology can be considered for the scaled-up treatment of emissions and air quality improvement inside livestock barns.

A large amount of data is produced every day by stakeholders of the Air Traffic Management (ATM) system, in particular airline operators, airports, and air navigation service provider (ANSP). Most data is kept private for many reasons, including commercial and security concerns. More than data, shared information is precious, as it leverages intelligent decision-making support tools designed to smooth daily operations. We present a framework to detect, identify and characterise anomalies in past aircraft trajectory data. It is based on an open source of ADS-B based aircraft trajectories, and extracted information can benefit a wide range of stakeholders: Air Traffic Control (ATC) training centres could play more realistic simulations; ANSP may improve capacity indicators; academics improve safety models and risk estimations; and commercial stakeholders, like airlines and airports, may use such information to improve short-term predictions and optimise their operations. The technique is based on autoencoding artificial neural networks applied on flows of trajectories, which provide a useful reading grid associating cluster analysis with quantified level of abnormality. In particular, we find that the highest anomaly scores correspond to poor weather conditions, whereas anomalies with a lower score relate to ATC tactical actions.

Determination of time-weighted average (TWA) concentrations of volatile organic compounds (VOCs) in air using solid-phase microextraction (SPME) is advantageous over other sampling techniques, but is often characterized by insufficient accuracies, particularly at longer sampling times. Experimental investigation of this issue and disclosing the origin of the problem is problematic and often not practically feasible due to high uncertainties. This research is aimed at developing the model of TWA extraction process and optimization of TWA air sampling by SPME using finite element analysis software (COMSOL Multiphysics). It was established that sampling by porous SPME coatings with high affinity to analytes is affected by slow diffusion of analytes inside the coating, an increase of analytes concentrations in the air near the fiber tip due to equilibration, and eventual lower sampling rate. The increase of a fiber retraction depth (Z) resulted in better recoveries. Sampling of studied VOCs using 23-ga Car/PDMS assembly at maximum possible Z (40 mm) was proven to provide more accurate results. Alternative sampling configuration based on 78.5 x 0.75 mm i.d. SPME liner was proven to provide similar accuracy at improved detection limits. Its modification with the decreased internal diameter from the sampling side should provide even better recoveries. The developed model offers new insight into optimization of air and gas sampling using SPME.

Low-cost personal exposure monitors (PEMs) to measure personal exposure to air pollution are potentially promising tools for health research. However, their adoption requires robust validation. This study evaluated the performance of twenty-one Plume Lab Flow2 (PLF) by comparing its air pollutant measurements, particulate matter with a diameter of 2.5 μm or less (PM2.5), 10 μm or less (PM10), and nitrogen dioxide (NO2), against several high-quality air pollution monitors under field conditions (at indoor, outdoor, and roadside locations). Correlation and regression analysis were used to evaluate measurements obtained by different PLFs against reference instrumentation. For all measured pollutants, the overall correlation coefficient between the PLFs and the reference instruments was often weak (r<0.4). Moderate correlation was observed for one PLF unit at indoor location and two units at roadside location, when measuring PM2.5, but not for PM10 and NO2 concentration. During periods of particularly higher pollution, 11 PLF tools showed stronger regression results (R2 values > 0.5) with one-hour and 9 PLF units with one-minute time interval. Results show that the PLF cannot be used robustly to determine high and low exposure to poor air. Therefore, the use of PLFs in research studies should be approached with caution if data quality is important to the research outputs.

Aero submarines (aerosubs) are vehicles that can both fly both in air and travel under water. The concept of dual aerial and aquatic vehicles emerged in 1939 when Russian engineer Boris Ushakov proposed the “flying submarine”[1], and this was followed by further developments including RFS1 [2], convair project in 1964[3] , etc. however, to date, limited attempt has been diverted towards the advanced development of such aircraft. This is heavily influenced by challenges associated with the design and operation of the same. Based on the review of literature the authors aim to introduce a theoretical design for an aerosub (QFS-20) with a view to address the design and operation issues including power, entry to and exit from water.

Cells receive external stimuli to incur structural and functional damages. On scanning acoustic microscopy (SAM), speed-of-sound (SOS), attenuation-of-sound (AOS), and thickness values are plotted on the screen to create cellular images, which are related to stiffness, viscosity, and cell size, respectively. The obtained digital data compared using statistical analysis. We aimed to investigate the effects of anticancer drugs, acidic fluids, and heat effects on the cells by using SAM. Anticancer drug cisplatin induced cancer cell apoptosis/necrosis and regeneration in culture, causing elevated SOS, reduced AOS, and thickness. During a more prolonged incubation, the SAM values fluctuated differently between the cisplatin-treated and untreated cells. The tannic and acetic acid and microwave stimuli induced SOS and AOS elevations. These stimuli altered the cell size, number, differentiation, viscosity, and stiffness, which corresponded well to the fluctuation of the SOS and AOS values after incubation. Different anticancer drugs interacted with cancer cells to induce the characteristic alterations of the SAM values. These structural and mechanical alterations induced in cells was difficult to observe on light microscopy. Cellular damages were statistically compared between different stimuli and time-lapse cellular changes were observed using a SAM analysis. SAM is a useful modality to evaluate cellular damage.

Fungi are ubiquitous and metabolically versatile. Their dispersion has important scientific, environmental, health, and economic implications. They can be dispersed through the air by the aerosolization of near surfaces or transported from distant sources. Here, we tested the contribution of local (scale of meters) versus regional (kilometers) sources by analyzing airborne fungal community by ITS sequencing around a copper mine in the North of Chile. The mine was the regional source, whereas soil and vegetal detritus were the local sources at each point. The airborne community was highly homogeneous in ca. 2,000 km2, impeding the detection of regional or local contributions. Ascomycota was the dominant phylum in the three communities. Soil and vegetal detritus communities had lower alpha-diversity, but some taxa had abundance patterns related to the distance to the mine and altitude. On the contrary, the air was compositionally even and unrelated to environmental or spatial factors, except for altitude. The presence of plant pathogens in the air suggests that other distant sources contribute to this region's airborne fungal community and reinforces the complexity of tracking the sources of air microbial communities in a real world where several natural and human activities coexist.

Fractal analysis of time series aims to extract the hidden or complex structures issued from the associated real data, such as scaling laws, non-stationary, dynamics, and so on. In the present work, the air quality index and its components are considered as time series owing fractal structures. To understand their underlying dynamics, wavelet multifractal approach is applied starting with a wavelet multifractal spectrum test to confirm the multifractality of the underlying data. Next, a new model is introduced improving the classical minmax one, provided with a statistical measure for the adequacy of the new model. The theoretical findings are applied to the north west Tabuk region of Saudi Arabia for environmental and climate data related to pollutants and factors involved in the estimation of the air quality index.

A single paragraph of about 200 words maximum. For research articles, abstracts should give a pertinent overview of the work. We strongly encourage authors to use the following style of structured abstracts, but without headings: (1) Background: place the question addressed in a broad context and highlight the purpose of the study; (2) Methods: describe briefly the main methods or treatments applied; (3) Results: summarize the article’s main findings; (4) Conclusions: indicate the main conclusions or interpretations. The abstract should be an objective representation of the article, it must not contain results which are not presented and substantiated in the main text and should not exaggerate the main conclusions.

The unquenchable demand for rock materials has attracted many companies within the building and construction sector to invest in stone quarrying. However, this has brought about the environmental impacts with health threats to people. There is a paucity of information about the magnitude of pollution on air and water and how it varies with quarry sites. This study therefore investigated the physical impacts of quarrying on air and water and explored the in-situ mitigations to undesirable effects due to stone quarrying. Four active quarry sites were identified. Field measurements of dust (particulate matter) was conducted within the four quarry sites and in the nearby community. Water samples were collected from quarry pits and nearby shallow wells for laboratory analysis of water quality. Statistical Analysis of Variance (ANOVA) was used to test for differences in pollution across the four studied sites. Results revealed that, amidst use of wet crushing and water sprinkling on bare surfaces, dust emission was higher than the recommended permissible standards levels with a significant variation across the quarry sites with ANOVA (P-value=0.003) for PM2.5 and (P-value=0.04366) for PM10. Water pollution was mainly contributed by the non-permissive levels of nitrates, chromium, and pH. Polluted air and water are associated with sparking off health threats to the users in the community. In conclusion, quarry companies should strengthen the already existing mitigation of dust suppression. The study recommends additional measures such as treating quarry pit water before discharging to the open environment

Social distancing policies put in place during COVID-19 epidemic in addition to helping to limit the spread of the disease also contributed to improving urban air quality. Here we show a decrease in air pollutant concentration as a consequence of mobility reduction in São Paulo during the containment measure which began on 22^nd March 2020. When comparing to foregoing weeks to equivalent periods of 2019, the concentration of most air pollutants sharply decreased in the first days of mobility restriction, to then increase again after government officials downplayed the threat of the disease. This trend is also followed by a decrease in hospital admissions by SARS-influenza. Therefore, despite the great economic and social unrest caused by the pandemic, this unique situation shows that large-scale mobility reduction policy had a significant impact on air quality, benefiting, directly and indirectly, the public health system.

Several methods have been tried to estimate air temperature using satellite imagery. In this paper, the results of two machine learning algorithms, Support Vector Machine and Random Forest, are compared with Multivariate Linear Regression, TVX and Ordinary kriging. Several geographic, remote sensing and time variables are used as predictors. The validation is carried out using four different statistics on a daily basis allowing the use of ANOVA to compare the results. The main conclusion is that Random Forest with residual kriging produces the best results (R$^2$=0.612 $\pm$ 0.019, NSE=0.578 $\pm$ 0.025, RMSE=1.068 $\pm$ 0.027, PBIAS=-0.172 $\pm$ 0.046), whereas TVX produces the least accurate results. The environmental conditions in the study area are not really suited to TVX, moreover this method only takes into account satellite data. On the other hand, regression methods (Support Vector Machine, Random Forest and Multivariate Linear Regression) use several parameters that are easily calculated from a Digital Elevation Model, adding very little difficulty to the use of satellite data alone. The most important variables in the Random Forest Model were satellite temperature, potential irradiation and cdayt, a cosine transformation of the julian day.

The air quality monitoring network in Alaska is currently limited to ground-based observations in urban areas and national parks leaving a large proportion of the state unmonitored. The use of MODIS aerosol optical depth (AOD) to estimate ground-level particulate pollution concentrations has been successfully demonstrated around the world, and could potentially be used in Alaska. In this work, MODIS AOD measurements at 550 nm were validated against AOD derived from AERONET ground-based sunphotometers in Barrow and Bonanza Creek to determine if MODIS AOD from the Terra and Aqua satellites could be used to estimate ground-level particulate pollution concentrations. The MODIS AOD was obtained from MODIS collection 6 using the dark target Land and Ocean algorithms from 2000 to 2014. MODIS data could only be obtained between the months of April and October; therefore, it could only be validated for those months. Individual and combined Terra and Aqua MODIS data were considered. The results showed that MODIS collection 6 products at 10 km resolution for Terra and Aqua combined are not valid over land but are valid over the ocean. On the other hand, the individual Terra and Aqua MODIS collection 6 AOD products at 10 km resolution are valid over land individually but not when combined. Results also suggest the MODIS collection 6 AOD products at 3 km resolution are valid over land and ocean and perform better over land than the 10-km product. These findings indicate that MODIS collection 6 AOD products can be used quantitatively in air quality applications in Alaska during the summer months.

Local air quality is a major concern for the population regularly exposed to high levels of air pollution. The airport, mainly due to its aircraft engines activities during taxiing and take off, is often submitted to heterogeneous but important concentrations of NOx and PM. The study suggests an innovative approach to determine the air traffic impact on air quality at the scale of the airport, its runways and terminals, in order to be able to locate the persistent high concentrations spots. The pollutants concentrations at 10 m resolution and 1 s time step are calculated in order to identify the most affected areas of an airport platform. A real day of air traffic on a regional airport is simulated, using real data as aircraft trajectories (from radar streams). In order to estimate the aircraft emissions, the Air Transport Systems Evaluation Infrastructure (IESTA) is used. Regarding local air quality, IESTA relies on the non-hydrostatic meso-scale atmospheric model Meso-NH using grid-nesting capabilities with 3 domains, for this study. The detailed cartography of the airport distinguishes between grassland, parking and terminals, allowing to compute exchanges of heat, water and momentum between the different types of surfaces and the atmosphere as well as the interactions with the building using a drag force. The dynamic parameters like wind, temperature, turbulent kinetic energy and pollutants concentration are computed at 10 m resolution over the 2 × 4 km airport domain. The pollutants are considered in this preliminary study as passive tracers, without chemical reactions. This preliminary study aims at proving the feasibility of high scale modelling over an airport with state of the art physical models.

When it comes to air pollution complaints, odours are often the most significant contributor. Sources of odour emissions range from natural to anthropogenic. Mitigation of odour can be challenging, multifaceted, site-specific, and is often confounded by its complexity—defined by existing (or non-existing) environmental laws, public ordinances, and socio-economic considerations. The objective of this paper is to review and summarize odour legislation in selected European countries (France, Germany, Austria, Hungary, United Kingdom, Spain, The Netherlands, Italy, Belgium), North America (USA and Canada), South America (Chile and Colombia), as well as Oceania (Australia and New Zealand) and Asia (Japan, China). Many countries have incorporated odour controls into their legislation. However, odour-related assessment criteria tend to be highly variable between countries, individual states, provinces and even counties and towns. Legislation ranges from (1) no specific mention in environmental legislation that regulates pollutants which are known to have an odour impact to (2) extensive details about odour source testing, odour dispersion modeling, ambient odour monitoring, (3) setback distances, (4) process operations, and (5) odour control technologies and procedures. Agricultural operations are one specific source of odour emissions in rural and suburban areas and a model example of such complexities. Management of agricultural odour emissions is important because of the dense consolidation of animal feeding operations and the advance of housing development into rural areas. Overall, there is a need for continued survey, review, development, and adjustment of odour legislation that considers sustainable development, environmental stewardship, and socio-economic realities, all of which are amenable to a just, site-specific, and sector-specific application.

The major auxin, indole-3-acetic acid (IAA), is associated with a plethora of growth and developmental processes including embryo development, expansion growth, cambial activity, and the induction of lateral root growth. Accumulation of the auxin precursor indole-3-acetamide (IAM) induces stress related processes by stimulating abscisic acid (ABA) biosynthesis. How IAM signaling is controlled is, at present, unclear. Here, we characterize an ami1/rooty double mutant, that we initially generated to study the metabolic and phenotypic consequences of a genetic blockade of the indole glucosinolate and IAM pathways in Arabidopsis thaliana. Our mass spectrometric analyses of the mutant revealed that the combination of the two mutations is not sufficient to fully prevent the conversion of IAM to IAA. The detected strong accumulation of IAM was, however, recognized to substantially impair seed development. We further show by genome-wide expression studies that the double mutant is broadly affected in its translational capacity, and that a small number of cell proliferation and plant growth regulating transcriptional circuits are repressed by the high IAM content in the seed. In accordance with the previously described growth reduction in response to elevated IAM levels, our data support the hypothesis that IAM is a growth repressing counterpart to IAA.

Every day around 93% of children under the age of 15 (1.8 billion children) breathe outdoor air that is so polluted it puts their health and development at serious risk. Due to the pandemic, however, ventilation of buildings using outdoor air has become an important safety technique to prevent the spread of COVID-19. With the mounting ev-idence suggesting that air pollution is impactful to human health and educational out-comes, this contradictory guidance may be problematic in schools with higher air pol-lution levels, but keeping kids COVID-19 free and in school to receive their education is now more pressing than ever. To understand if all schools in an urban area are ex-posed to similar outdoor air quality and if school infrastructure protects children equally indoors, we installed research grade sensors to observe PM2.5 concentrations in indoor and outdoor settings to understand how unequal exposure to indoor and out-door air pollution impacts indoor air quality among high- and low-income schools in Salt Lake City, Utah. Based on this approach, we found that during atmospheric inver-sions and dust events, there was a lag ranging between 35 to 73 minutes for the out-door PM2.5 concentrations to follow a similar temporal pattern as the indoor PM2.5. This lag has policy and health implications and may help to explain the rising concerns re-garding reduced educational outcomes related to air pollution in urban areas. These data and resulting analysis show that poor air quality may impact school settings, and the potential implications with respect to environmental inequality.

The provision requirement of 10% openings of the total floor area stated in the Uniform Building by Law 1984 Malaysia has been practiced by designers for building plan submission approval. However, the effectiveness of thermal performance in landed residential buildings, despite the imposition by the by-law, has never been empirically measured and proven. Although terraced houses in Malaysia have dominated 40.9% of the total property transaction in 2019, such mass production with typical designs hardly provides its occupants with thermal comfort due to the static outdoor air condition and lack of external windows, where the conventional ventilation technique does not work well, even for houses with an air well system. Consequently, the occupants need to rely on mechanical cooling, which is a high energy-consuming component contributing to outdoor heat dissipation and therefore urban heat island effect. Thus, encouraging more effective natural ventilation to eliminate excessive heat from the indoor environment is critical. Since most of the research focuses on simulation modelling lacking sufficient empirical validation, this paper drawing on field measurement investigates natural ventilation performance in terraced housing with an air well system. More importantly, the key concern as to what extent the current air well system serving as a ventilator is effective to provide better thermal performance in the single storey terraced house is to be addressed. By adopting an existing single storey air welled terrace house, the existing indoor environmental conditions and thermal performance were monitored and measured using scientific equipment, namely HOBO U12 air temperature and air humidity, the HOBO U12 anemometer and the Delta Ohm HD32.3 Wet Bulb Globe Temperature meter for a six-month duration. The findings show that the air temperature of the air well ranged from 27.48°C to 30.92°C, while the mean relative humidity were from 72.67% to 79.25%. The mean air temperature for a test room (single sided ventilation room) ranged from 28.04°C to 30.92°C with a relative humidity of 70.16% to 76%. These empirical findings are of importance, offering novel policy insights and suggestions to potentially revising the existing building code standard and by laws; since the minimum provision of 10% openings has been revealed to be less effective to provide a desired thermal performance and comfort, mandatory compliance with, and the necessity for, the bylaw requirement should be revisited and further studied.

The aim of this work is to provide a full description of how air temperature and solar radiation induce changes in the land cover over an Antarctic site. We use shortwave broadband albedo (albedo integrated in the range 300-3000 nm) from a spaceborne sensor and from field surveys to calculate the monthly relative abundance of landscape units. Field albedo data were collected using a portable albedometer over seven landscape units: clean fresh snow; clean old snow; rugged landscape composed of dirty snow with disperse pyroclasts and rocky outcrops; dirty snow; stripes of bare soil and snow; shallow snow with small bare soil patches; bare soil. MODIS MCD43A3 daily albedo product was downloaded using the Google Earth Engine API from the 2000-2001 season to the 2020-2021 season. Each landscape unit was characterized by an albedo normal distribution. The monthly relative abundance of the landscape units were calculated by fitting a linear combination of the normal distributions to the histogram of the MODIS monthly mean albedo. The monthly relative abundance of the landscape unit consisting of rugged landscape composed of dirty snow, with dispersed clasts and small rocky outcrops exhibits a high linear positive correlation with the monthly mean albedo (R2=0.87) and a high linear negative correlation with the monthly mean air temperature (R2= 0.69). The increase of the solar radiation energy flux from September to December coincides with the decrease of the relative abundance of the landscape unit composed of dirty snow with dispersed clasts and small rocky outcrops. We propose a mechanism to describe the evolution of the landscape: uncovered pyroclasts act as melting centres favouring the melting of surrounding snow. Ash does not play a decisive role in the melting of the snow. The results also explain the observed decreasing of the thaw depth of the permafrost on the island in the period 2006-2014, resulting from an increase in the snow cover over the whole island.

Different coffee drying technologies face complex task in ensuring an acceptable final seed moisture content. Drying technology of agricultural commodities aims to maintain and improve the quality of the agricultural products themselves. In addition to maintaining quality, especially from other bacterial attacks, it can last for a long time before further processing. Coffee commodities are promising for the welfare of coffee farmers. Drying technology plays a major role in determining the quality of coffee. Various drying models are applied including the traditional model that until now is still applied, direct drying under solar radiation. However, this drying process is less hygienic and requires a large area. Thus, one of the drying technologies that can accelerate drying time is to vary the air flow in the drying chamber so that the coffee can be determined to reduce the water content with a certain temperature. In this study, it was found that the moisture content of coffee beans dried using a dryer on air flow with variations of velocity in solar collector 1 (DB1) air velocity of 1.0m/s obtained the final mass = 732.249 gr, solar collector 2 (DB2) with air velocity 1.5 m/s obtained the final mass = 774.70 gr, solar collector 3 (DB3) with air velocity 2.0 m/s obtained the final mass = 855.10 gr, solar collector 4 (DB4) with air velocity 2.5 m/s obtained the final mass = 745.79 gr, and solar collector 5 (DB5) with air velocity 3.0 m/s obtained the final mass = 786.40 gr. Water Content DB1=12.0%, DB2=13.6%, DB3=18.5%, DB4=12.9% and DB5=15.2%. The time required for 25 hours with a maximum radiation of 586.9 w/m2, total heat utilized from solar radiation in 3 days =16.663128 MJ/m2. from the initial weight of 1500gr coffee bean samples and dried in five solar collectors with parallel simultaneously. The evaporated water content DB1=51.18%, DB2=48.35%, DB3=42.96%, DB4=50.28% and DB5=47.57%. Based on this research, it was found that the most optimum quality of coffee was by using solar collector 2 (DB2), namely with air flow of 1.5 m/s with average temperature in the drying box DB2=43.68°C, with the quality content of the coffee, Protein content=12.2%, Carbohydrate=22.8% and Free Fatty Acid (ALB) content=0.05%.

TiO2-based building materials have air purification, auto-cleaning and sterilization functions, and these innovative green building materials have great potential for energy-saving and emission reduction applications in the future. However, there are still great challenges in improving photocatalytic efficiency and stability from laboratory to practical applications. In recent years, researchers have done a lot of work to improve the efficiency and stability of TiO2-based building materials. This paper briefly discussed the air purification principle by photocatalytic building, and the preparation techniques of TiO2-based building materials and the strategies to improve the efficiency of TiO2. Moreover, this paper has outlined the key factors that affect the photocatalytic building performance in practical applications, and analyzed the limitations and future development trends. Finally, we proposed some suggestions for further research on photocatalytic buildings and its application in practice, aiming to provide an efficient reference for developing highly efficient and stable photocatalytic building materials. The aim of this paper is to provide effective guidance for the application of TiO2-based photo-catalysts in the field of green buildings, helping to develop more efficient and stable low-carbon buildings for the development of sustainable cities.

The outbreak of the COVID-19 pandemic has raised concerns about potential environmental factors that could influence the spread and severity of the SARS-CoV-2 virus. Atmospheric pollution, particularly particulate matter (PM), has been suggested as a contributing factor to viral infections and respiratory complications. This two-year observational study aimed to investigate the relation between air pollution and the spread of COVID-19, focusing on PM2.5. Unlike previous studies limited to specific cities or countries, inevitable to use temporal data. Our research analyzed data from various states across the United States, considering both spatial and temporal correlation. The analysis considered the number and geographic distribution of COVID-19 cases along with daily PM2.5 exposure levels, accounting for monthly average PM2.5 exposure, from March 2020 to December 2021. The observed conflicting results of the temporal and spatial correlation present challenges for researchers in understanding the true nature of the relationship between PM2.5 air pollution and COVID-19 cases. The correlation between various factors, such as population density, PM2.5, temperature, and wind speed, and COVID-19 refers to an association or statistical relationship, not causation. Moreover, the intricate interplay of these variables makes it difficult to establish a clear cause-and-effect relationship.

The research considers creating a network of moss-based biotechnological purification filters in the Smart City concept. The extent of absorption of heavy metals and gases by Sphagnopsida moss under different conditions was investigated. The efficiency of air purification with biotechnological filters was also investigated using the example of the city of Almaty, Republic of Kazakhstan, where an excess of the permissible concentration of harmful substances in the air, according to the WHO air quality guidelines, is recorded throughout the year. Data on the level of pollution recorded by sensors located in the biggest Kazakhstani cities from 06/21/2020 to 06/04/2023 were selected as the basis for calculating the efficiency. In total, there are two hundred twenty sensors in 73 settlements of the Republic of Kazakhstan, with 80 such sensors located in the city of Almaty. Since creating a single biotechnological filter is expensive, the task was to calculate the air purification effect in the case of increasing the number of filters placed in polluted areas. As a result, it is shown that ten filters provide an air purification efficiency of 0.77%, 100 filters 5.72%, and 500 filters 23.11%. A biotechnological filter for air purification based on moss was designed at Astana IT University, considering the climatic features, distribution, and types of pollution in the Republic of Kazakhstan. The obtained results are essential for ensuring compliance with the ISO 37120:2018 standard for environmental comfort in the Republic of Kazakhstan. Additionally, the research findings and the experience of implementing a moss-based biotechnological filter can be applied to designing similar air purification systems in other cities. This is of great importance for the advancement of the field of urban science.

Air pollution is a man-made environmental-related problem and has importance globally among all environmental issues. It is described as an atmospheric situation in which several components appear at high attention above their ambient level and generate a quantifiable effect on vegetation, animals, and people. Air pollution and its control are a universal problem and have become an issue of great trouble for us in current years. However, monitoring and measurement of the concentration of air pollutants are most difficult in assessment to monitoring other components in the environment. Air pollutants are transported to polar regions by different mechanisms such as long-range atmospheric transport or grasshopper effects and via anthropogenic activities. After reaching the polar regions, they settle down and remain as such for a long-time due to their persistent nature. They can distress the environment and wildlife of the polar regions. Generally, dangerous chemicals may cause a risk of well-being effects, whereas lethal pollutants focus on one physiological reaction. We reviewed the available information on air pollution (occurrence, sources, and harmful effects) in the polar regions.