Natural fibers have attracted increasing interest as an alternative to produce environmentally friendly and sustainable materials. Particularly, hemp fibers have revealed to be widely used in various industrial applications due to their extremely unique properties. However, hemp can generate a large amount of agro-waste, and results in an attractive source of biopolymers for the development of low-cost materials in alternative to the raw materials and conventional petroleum-based plastics. In addition, deep eutectic solvents (DESs), a new type of truly green solvents, have been tested to remove gums, lignin, and other non-cellulosic components from hemp fibers. Reusing these components dissolved into the DESs to fabricate new materials directly by electrospinning is a very attractive but still unexplored endeavor. Thus, this innovative research to venture new upcycling pathways is focused on the fabrication of composite nanofibers by electrospinning of a gel-based blend of Poly(vinyl alcohol) (PVA) and hemp agro-waste (HW) dissolved into choline chloride (ChCl) : Glycerol (1:2) and ChCl : Urea (1:2) DES mixtures. The results obtained revealed that the produced nanofibers displayed uniform appearance with diameters ranging from 257.72 ± 65.63 nm to 380.78 ± 133.98 nm. In addition, the mechanical properties of the electro-spun composite nanofibers produced from the gel-based blends of HW dissolved in DESs and PVA (HW-DESs_PVA) were found to be superior, resulting in an enhanced tensile strength and Young’s modulus. Furthermore, the incorporation of HW into the nanofibers was able to provide bioactive antioxidant and antibacterial properties. Overall, this study demonstrated a promising, more sustainable, and eco-friendly way to produce electrospun composite nanofibers using HW in a circular economy perspective.

A tumbler screen type residual film–impurity mixture wind separator as a key equipment for secondary utilization of farmland residual film. During the working process, the proportion of impurities in the separated waste mulch film intermittently increases, resulting in poor working stability of the device, which may hamper long-term operation. In this study, the material inside the separation unit was continuously monitored, and the main factor affecting separator per-formance was determined to be the challenges in the effective depolymerization of some residual film–impurity mixtures. The principles of agglomeration and depolymerization of the residual film–impurity mixtures were analyzed using computational fluid dynamics (CFD) and discrete element method (DEM) flow-solid coupling simulation methods. The key factor affecting the disaggregation of the mixture was the collision force between the residual film–impurity mixture and the trommel screen. The collision force was maximum when the residual film–impurity mixture first collided with the trommel screen when it was fed into the separation device. As determined by force analyses, the key factors affecting the collision force of the process were the material feeding amount and the structure of the inlet. Furthermore, simulations were carried out for different inlet structure forms; the evaluation index was the maximum collision force of the residual film–impurity mixture agglomerate on the trommel screen. The best disaggregation effect was obtained with a square feed inlet and at a feeding rate of 202 kg/h. A prototype was built using these specifications for verification. The average value of the ratio of impurities in the re-sidual film was 6.966%, the coefficient of variation was 7.38%, and the dispersion of statistical results was small. The ratio of impurities in the residual film was kept constant during the con-tinuous operation of the wind separator. Thus, this study analyzed the agglomerate disaggregation process and provided theoretical insights for deter-mining the optimal structures of the inlets of various cleaning devices and the feeding volumes.

In the last ten years, plasma waste treatment has gained increasing prominence as a technology in response to growing challenges in waste disposal and the recognition of opportunities for generating valuable by-products. The efficiency and outcomes of this process are intricately linked to the characteristics of the plasma involved, such as plasma enthalpy and heat flux. We employed an experimental radio frequency inductively coupled plasma (RF-ICP) torch operating at atmospheric pressure to generate plasma. Utilizing optical emission spectroscopy (OES), we measured plasma parameters, specifically the effective electron temperature (Teff) and plasma density (ne), while varying argon gas flow rates and RF powers. Our investigations revealed that both flow rate and RF power exert significant control over plasma parameters, and we observed an unusual phenomenon within this range of discharge pressures. Consequently, both the plasma's enthalpy and the heat flux it generates are influenced by variations in both flow rate and RF power.

Enzymes are biological molecules produced by living entities for carrying out biological processes. The application of enzymes for waste treatment has been gaining pace commercially to solve concerns related to agricultural residues, wastewater, replacement of synthetic processes with natural ones, etc. The application of enzymes for waste management has been an environmentally reliable and sustainable process. Treatment of waste with enzymes such as xylanase, proteases, hydrolases, cellulose, peroxidases, chitinases, laccases, etc. has been studied to be effective. These enzymes act upon the waste products and transform them into biodegradable forms that can be recycled, reused and converted to value-added products. They have wide applications and utility as it has been an effective approach, economically cheaper and sustainable techniques. Application of such enzymes for waste management would be beneficial for reducing the quantity of waste, diminishing the negative effects of waste and pollution on the environment, and would be beneficial in bio-converting the waste products into alternate sources of energy. The current chapter focuses on different types of enzymes, their applications for waste management, and their limitations. This chapter also emphasizes the usage of some prominent microorganisms, their secreted enzymes and their proposed mechanisms of action involved with the degradation of the waste products.

Botanical recycled concrete, or concrete bonded with wood, is formed by heat pressing the mixture of concrete and wooden waste. Botanical recycled concrete is a relatively new material and the relationship between production condition and its real-world performance is not clear yet. This experimental study investigated the influence of several production condition factors on the density and bending strength of botanical recycled concrete. As a result, temperature and mass ratio of concrete powder to wood flour presented significant effects on the density of this botanical recycled concrete. The increase in production temperature resulted in a remarkable increment in density and bending strength. This is probably due to increased wood flowability and accelerated compaction and bonding formation. The fineness of wood flour had a significant effect on improving bending strength. This is attributed to a larger contact surface between the wood substance and concrete particles.

Global waste generation keeps increasing over the year and requires innovative solutions to minimize their impacts on environmental quality and public health. Predicted 2.2 billion tonnes per year of global municipal waste generation in the year 2025 which 1.6 fold is higher than in 2012. Hence, a strategic plan must be ascertained to overcome the future challenges of MSW locally and globally. Universiti Putra Malaysia (UPM) coined an initiative to demonstrate a showcase pilot plant for green energy production from MSW. Therefore, the data was obtained from the survey and actual sampling within the UPM compound to estimate the MSW generated and it's potentially used for green energy production. It is estimated that 5.0 – 7.0 tonne per day of MSW generated which about 30 - 35% is an organic fraction. Upon separation, the organic fractions were digested into biogas through anaerobic. At the maximum conversion of organic fraction, about 775 kWh of electricity may able to generate from the waste. In this study, the complete biorefinery setup and utilize organic components from the MSW generated in UPM was proposed that the biogas subsequently will be used to produce green energy in the form of electricity or cooking fuel.

The aim of this research study was to develop hydrogels samples for using in potential biomedical applications. Hydrogels consisting of different volumes of keratin, polyvinyl alcohol (PVA), Polyvinylpyrrolidone (PVP), and starch. The keratin is derived from the chicken was the primary material on the hydrogels due to attractively for the potential wound healing application. The hydrogel samples were made by using the freeze‑thawing method, and they were examined using the Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), porosity amusement, swelling ratio and keratin release kinetic models that analyzed using (zero-order, first-order Higuchi and Korsmeyer-Peppas models). These results were indicated that feather keratin could use with formulated hydrogels suitably for controlled keratin release studies .

The possibility of making precious stones from radioactive waste is being considered. Vitrified and cemented radioactive waste (RW) is considered as an artificial rock belonging to aluminosilicates and calcites. Two methods are proposed for the manufacture of radioactive gemstones from RW and their subsequent storage with the possibility of sale, resale, inheritance, and so on. That is, RW is considered as real estate in which capital can be invested. After decontamination in hundreds and thousands of years, it will be of scientific, historical, jewelry interest.

An adequate number of waste management facilities is the key element to meet circular economy goals. Using empirical data taken from official sources the research framework bases on an econometric model to compare the elasticity of cost on quantity of different alternatives such as waste-to-energy facilities, mechanical biological facilities and landfills impact on waste management cost. Results suggest that both waste-to-energy facilities (-0.278%) and landfills (-0.38%) concur to lower the cost while the higher the percentage of waste sent to mechanical biological treatment facilities, the higher the cost (0.788%). This figure deserves to be examined in more details as such facilities represent an intermediary step in the chain which efficiency depends on the industrial organization of the chain.

This study was undertaken to forecast waste generation rates of accommodation sector of North Cyprus as a case. Three predictor models including multiple linear regression (MLR), artificial neural networks (ANNs) and central composite design (CCD) were applied to predict the waste generation rate during the lean and peak seasons. ANN showed highest prediction performance, specifically, lowest values of the standard error of prediction (SEP = 2.153), mean absolute error (MAE=1.378) and highest R2 value (0.998) confirmed the accuracy of the model. The analysed wastes were categorised into recyclable, general waste and food residues. The authors estimated the total waste generated during the lean season as 2010.5 kg/day, in which large-sized hotel accounted for largest fraction (66.7%), followed by the medium hotels (19.4%) and guesthouse accounted for smallest part (2.6%). During the peak season, about 49.6% increases in the waste generation rates were obtained. Interestingly, 45% of the wastes were generated by the British tourists while the least waste was generated by African tourists (7.5%). The ANN predicted that the small and large hotels would produce 5.45 and 22.24 tons of waste by the year 2020, respectively. The findings herein are promising and useful in establishing a sustainable waste management system.

Waste management is a significant issue that Indonesia must face. The presence of waste will always exist as long as life continues. One of the main challenges in waste management is the proper separation of organic and inorganic waste. As a solution to address this issue, the Ministry of Environment has made efforts to develop Waste Banks. However, it also creates new problems related to manual data collection, lack of monitoring by the community in implementing waste management activities, and a lack of specific reports regarding waste management conducted by officers. We propose the creation of a website using the Agile Development SDLC method. This website involve several steps and incorporate functions for data digitalization and expedited data collection, such as the addition of QR Code functionality, Monthly Reporting Function, and enhanced data security. The method used in this research is Agile Development. The application has been developed with a user-friendly interface and the latest web development technologies to ensure smooth performance. Overall, the web-based application for organic and inorganic waste using Laravel is an important step to promoting sustainable waste management practices.

Concrete production requires a significant amount of natural resources, with aggregates comprising between 55% and 80% of the total volume. However, over-exploitation of natural aggregates has led to the exploration of alternative materials for use in concrete production. In this study, crushed hazelnut shells were investigated as a partial replacement for fine aggregate, addressing the problem of natural resource depletion and offering a second use for this important agricultural waste product available in Chile. Hazelnut shells were incorporated in percentages of 2.5%, 5%, and 10% by weight of sand for water-cement ratios of 0.4 and 0.5. The compressive strengths at 7 and 28 days and bending tensile strengths at 28 days were determined, alongside physical properties such as workability, temperature, air content, fresh density, and hardened density of the concrete. Our findings show that replacing 2.5% of the fine aggregate with hazelnut shells led to higher compressive strength at 28 days, exceeding the strength of the standard specimens by 9.5%, whereas replacing 5% of the fine aggregate led to the highest bending tensile strength, exceeding the resistance of the standard specimens by 3.5%. Moreover, the 0.4 w/c ratio consistently led to better results for both compressive and bending tensile resistances, with fewer and lower reductions in mechanical resistances compared to the standard mixture. Our results suggest that concrete mixes with hazelnut shells as a replacement for fine aggregate at a percentage of up to 2.5% can be used in constructive systems with compression strengths lower than 17 MPa, and mixtures with up to 10% hazelnut shell replacement can be used in structures with tensile bending stress requirements lower than 6 MPa. Overall, the use of hazelnut shells as a partial replacement for fine aggregate in concrete production presents an environmentally-friendly and cost-effective solution for the construction industry.

The use of food waste disposers in gastronomical facilities influence the municipal wastewater composition. Ground food waste poses problems in the operation of the sewerage network and generates high electric energy consumption in wastewater treatment plants (WWTP). The study aimed to determine, for five towns with a PE of 4,000 to 220,000, the volumes of catering waste discharged to the WWTPs. The towns differed in the number of inhabitants, beds in hotel and catering places. The calculations were made based on data received from the operators of WWTP. The pollutant concentrations in 2019, were compared with data from the "pandemic" year - 2020. The loads of catering waste entering the sewerage system in 2019 ranged from 32.7 to 1062 tons. In town with the largest tourist base, the BOD value in 2020 accounted for 62.3% of 2019 value. In the largest town, the annual energy consumption for food waste treatment could be up to 2,539,770 kWh. If the waste was fermented, it could be obtained up to 1,376,650 m3 of methane. There is a strong need for implementing a collection system for food waste from catering facilities and its fermentation to produce methane, which can be used for energy purposes.

Hyperspectral imaging data holds great potential for the different stages of the mining life cycle in active and post-mining environments. However, the technology has yet to reach the stage of large-scale industrial implementation and acceptance. While hyperspectral satellite imagery can achieve high spectral resolution, signal-to-noise ratio (SNR) and global availability with break-through satellite systems like EnMAP, EMIT and PRISMA, limited spatial resolution poses chal-lenges for sectors like mining, which require decimetre to centimetre scale resolution for applica-tions such as reconciliation, ore/waste estimates, geotechnical assessments and environmental monitoring. Hyperspectral imaging from drones (referred to herein as Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the camp/ mine scale, with the capability for frequent, user-defined re-visit times. This has been made possible by the miniaturization of hy-perspectral imaging systems. Collection of data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions enables the detection of different minerals and surface altera-tion patterns potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we provide a review of relevant studies de-ploying hyperspectral imaging in or applicable to the mining sector, especially for the use of hy-perspectral VNIR-SWIR Uncrewed Aerial Systems. Where required, we draw on previous in-sights derived from satellite or ground-based systems. We also discuss UAS survey planning, and sampling considerations for validation and interpretation.

Composting is one of the most economical and environmentally safe methods of recycling organic waste. Soil microorganisms play a significant role in decomposition and the availability of plant nutrients. This study was designed to prepare a suitable microbial inoculum and its evaluation on composting heap to decrease the time of waste degradation. The bacteria were isolated and molecular characterized from the soil near composting area by using 16S ribotyping technique. The identified strains of bacillus cereus used as an inoculum gives better results to expedite the degradation of organic waste. The prepared bacterial inoculum with molasses was also compared with commercial inoculum by optimizing physical and chemical parameters (temperature, oxygen, C: N, pH, and moisture content) of composting heap. Monthly reading of these parameters was taken from experimental and control treatments. The highest decomposition rate of organic waste was recorded in treatment A (experimental heap) where molasses and bacterial inoculum were added and less decomposition was observed in treatment D (experimental heap) where no inoculum and molasses were added. It was concluded from the studies that the prepared bacterial inoculum with two strains of Bacillus was effective and prepared mature compost in 2.5 months by increasing decomposition efficiency of organic waste. Furthermore, the prepared compost was also sustainable in its physical and chemical characteristic.

Any Hospital’s primary goal is to restore human health and save lives through health services provided to patients, but at the same time, hazardous wastes are produced. Inconsistent management of unsafe wastes might cause adverse effects and other issues to workers, the environment and public health. Segregation is considered the critical stage for a successful Healthcare Waste Management. Mixing hazardous waste with non-hazardous waste will be avoided by correctly applying practices at the segregation stage. This study aimed to assess personnel’s knowledge about Infectious Medical Waste and segregation practices used at six wards in Nicosia General Hospital. An analytical cross-sectional study was conducted, and data were collected through a structured self-administered questionnaire. The Statistical Package of Social Science (SPPS) version 25 was used with a minimum statistical significance α=0.05. The study population was nurses, nurse assistants, ward assistants and cleaners working at the study wards. Out of 191 questionnaires, 82 were received, with a response rate of 42.93%. Most participants were female (72%) and nurses (85,4%). Participants had medium to good knowledge about Infectious Medical Waste management and good knowledge regarding segregation practices applied in their ward. Segregation was not carried out as it should have since most participants stated that Infectious Medical Wastes were mixed with non-hazardous waste. Correct answers given by the participants regarding color-coding of different Healthcare Waste categories was 67.5%, and only four answered correctly to all questions. Although participants knew segregation practices and the colour-coding process applied for Healthcare Waste, they didn’t use them satisfactorily. They applied methods regarding segregation without specific training, knowledge and guidance. Due to the issue's importance, training programs must be implemented and performed.

The management and classification of solid waste is one of the most important challenges around the world, in order to sustain economic growth and preserve the environment. The objective is to propose the use of Smart Ecological Points as a strategy to address the problem related to the solid waste management system at the source, which has become one of the biggest problems globally and Colombia is no exception. The article describes the current state of the problem in the country and in turn, presents the possibility of developing a prototype corresponding to a low-cost Smart Ecological Point supported by the use of an experimental capacitive sensor and Machine Learning algorithms, which will reduce the time necessary for the classification of recyclable and non recyclable waste, minimizing the health risks and increasing the percentage of waste that can be reused, by reducing the probability of being contaminated at the source, an aspect that is very common when done manually. According to the results obtained, it was evident that the proposed prototype made an adequate classification of waste, generating the possibility of being manufactured with existing technology in the environment, in order to promote adequate waste classification at the source.

The article discusses an alternative way of recycling radioactive waste (RW), presented in the form of radioactive building materials - concrete and reinforced concrete structures and metal fittings, with the further use of materials, obtained during recycling, in the space industry. That is, it is supposed to send radioactive waste into space not as a passive ballast, but as a payload that will operate in space under conditions of increased radiation.

Insecticide testing facilities that evaluate a variety of vector control products may generate large amount of hazardous wastes from routine operations. These wastes originate from degraded technical grade materials, sprayed substrates, redundant stock or working insecticidal solutions. The washing of Long-Lasting Insecticidal Nets (LLINs) during preparation for laboratory and experimental hut trials also contribute to waste water with insecticide content. Human and environmental exposure to insecticidal waste can occur during transport, categorization, storage and disposal in resulting in environmental pollution and potential health effects. Various national and international guidelines have been devised for safe disposal and should be strictly followed to avoid adverse effects on humans or environment. The current paper describes a case study from insecticide test facility in north-eastern Tanzania in management of insecticidal waste.

Organic fertilizers are fertilizers made from organic materials which are partly or wholly derived from waste materials, the function of these fertilizers is to improve the physical, biological, and chemical properties of the soil, these fertilizers are processed through the composting process, these fertilizers are very much needed because they are difficult to obtain at a high price. expensive. This study aims to obtain data on the growth and yield of sweet corn, due to the use of agricultural waste as organic fertilizer. The research method was experimentally consisting of 5 treatments and 5 replications; ie P0 = Without organic fertilizer (control) P1 = Dosage of organic fertilizer 2.5 tons/ha, P2 = Dosage of organic fertilizer 5 tons/ha P3 = Dosage of organic fertilizer 7.5 tons/ha, P4 = Dosage of organic fertilizer 10 tons /ha using a Randomized Block Design (RBD) The results showed that organic fertilizer had a significant effect on plant height aged 30, 40 and 50 DAP, had a very significant effect on cob length at a dose of 10 t.ha-1 and, had no significant effect on cob weight, will still have a high weight of 350 g.cob-1 From this description it can be concluded that organic compost can be used as a substitute for chemical fertilizers which provides an increase in the growth and production of sweet corn plants at the use of 10 tons/ha.

More than 800 million tons of fish are utilizing in a year and 25-30% become waste. The waste amount is beneficial source for extraction of collagen. But procedure of extraction is still to be optimized. The current study was designed to extract collagen from fish through fish waste fermentation under various conditions. For collagen extraction we did lactic acid fermentation in which yogurt and Dough bacteria was added with fish sample and placed it in incubator at 30ºC for one month. In yogurt and dough culture have at least 10 type of lactic acid bacterial species. After every week we check PH of each sample and take soup of that sample. After centrifugation of that sample’s TCA (Trichloroacetic acid) precipitation was done of yogurt and dough sample and kept at -20ºC. then did SDS-PAGE) using 6% resolving and 5% stacking gel of already stored sample. Then HaCaT cells (1 × 10⁴ cells/well) were cultured in 96-well flat-bottom culture plates and treated with appropriate doses of FFCP (fermented fish collagen peptide) for 24 and 48 hours.The SDS-PAGE revealed that the collagen protein of fish had doublet pattern for α1 and α2 chains at corresponding to 145 kDa and 132 kDa respectively. The density for α1 twice as compared to α2. Our result agrees that The fish collagen consists mostly of α-chain as well as little amount of inter and intra molecular cross-linked components of α-chains; b (dimmer) and c (trimer). Different biochemical tests were done for identification of lactic acid bacteria catalase positive, citrate positive, urease negative. Our fermented fish collagen and peptides mixture were test for cellular cytotoxicity and proliferative effect on HaCaT cells. Current result shows that fermented extracted collagen are nontoxic and induce the proliferation of HaCaT cells. Current study is supported by various studies that revealed the medical application of fish extracted collagen as underline.

The size of the population and the need for residential spaces are increasing. One possible solution is to add new floors to existing buildings. The positive aspects of such a solution with respect to its socio-economic impact and impact on the environment is that large amounts of carbon dioxide release will be avoided, waste and its treatment will be reduced, and agricultural land and green spaces will be preserved. However, adding floors to existing structures might be structurally challenging, especially in terms of the behavior under seismic actions. This paper presents a numerical study of a reinforced concrete frame in an old building to which new floors are subsequently added. The analysis shows that the frame does not behave as a whole with the old part of the structure, nor does it behave the same as if it were made with rigid joints compared to additional ones connected using hinge joints. The change from the corner (knee) joint to the external joint has its own effect on the distribution of internal forces in the structure as a whole and in the joint in particular.

Recently, the amount of waste generated has been rapidly increasing, there have been difficulties disposing of waste in Korea. As a solution to this, treating waste using a cement kiln has suggested, but the environmental and economic effects have not been specifically studied. In this study, the effects of alternative resources, and reducing the social costs(Installation and Operation) associated with waste treatment facilities were analyzed. Through a co-processing method, a reduction of approximately 53kg of CO2 can be realized during the production of one ton of cement, and cost savings of about 3,815 milion USD. Another effect is an extension of the expiration date for landfills by 7.55 years.

We are experiencing an unprecedented urbanization process that alongside with physical, social and economic developments is having a significant impact on population’s health. Due to higher apprehensions of pollution, violence and poverty, our modern cities no longer ensure a good quality of life so they become unhealthy environments. This study aims to measure the socio-environmental and hematologic profile of residents of Santo André’s landfill – “Bairro Espírito Santo” by using the contextualization of the studied area. The research method is Observational type and from Retrospective cohort and by convenience sampling in Santo André in the Greater ABC region. The study determined a socio environmental profile and the hematologic diseases screening related to a close location to the landfill. The disease manifests itself within a broad spectrum of symptoms that causes changes in blood count parameters. The full blood counts analysis was performed, indicating that the blood counts of residents living near the landfill led to positive hematological changes and diseases like Leukopenia, Anemia, Neutropenia and lymphocytosis were the most common changes. However it is considered that the proof of the relation of cause- effect to environmental exposures that may trigger chronic manifestations in humans requires specific studies that are often complicated.

Excessive production, consumption and indiscriminate disposal of plastic waste cause an increasing plastic pollution with detrimental impacts on environment and human health. This study aimed to assess the level of knowledge, attitude, and practices (KAP) towards plastic pollution among Malaysians and evaluate the variation of plastic pollution related KAP among various socio-demographics. An online survey was conducted, and 294 valid responses was obtained. Descriptive statistics, KAP scoring and cross tabulation of responses were estimated. One-way analysis of variance, paired t-test and binary logistic regressions were carried out. Results showed that respondents had poor knowledge (mean 7.41 ± 1.80) and practice score (3.81 ± 1.39) across all socio-demographics. Compared to younger (18-30 years) respondents, older ones (>46 years) had higher knowledge (odds ratio, OR 4.304; p<0.01). However, middle aged (31-45 years) respondents reported significantly (p<0.01) higher attitude (OR 4.019) and practice (OR 4.056; p <0.05). Respondents with environmental related university education had showed higher odds about plastic pollution related knowledge (OR 10.343; p<0.01). Suggestions are made to undertake interventions such as environmental awareness creation, incorporating plastic pollution topics in formal and informal education, and providing recycling facilities nearby the localities for encouraging good practices towards minimizing plastic uses and pollution.

COS production is carried out enzymatically using chitosanase, but this process is expensive. Production costs can be reduced by using crude enzyme chitosanase, and the resulting COS has depolymerization &lt; 20 and molecular weight &lt; 3900 Da. Sources of crude enzyme chitosanase come from the soil, sediment, and fishery waste. Chitosanase is produced from bacteria and molds isolated from the source or direct isolation process for extracellular enzymes, especially from fishery waste. Microorganisms in the soil produce chitosanase as a biocontrol and self-defense agent. Bacteria and molds have been isolated, including Bacillus cereus, Bacillus mycoides, Paenibacillus sp., and Penicillium janthinellum. Fishery waste, especially parts of the digestive tract, is a source of chitosanase because of its relation to its nature and food, such as small fish, frogs, and several types of crustaceans. In addition, fishery waste can be used as a carbon and nitrogen source (C/N) in microorganism culture media. The chitin content becomes a stimulant for the synthesis of chitosanase by microorganisms. Crude enzyme chitosanase has an active site that hydrolyzes chitosan by breaking glycosidic bonds and producing glucosamine units (GlcN) and N-acetyl glucosamine (GlcNAc). This mechanism can take place through two events, namely inverting and retaining. Crude enzyme chitosanase can break glycosidic bonds, especially with the same groups, for example, bonds between glucosamine or N-acetyl glucosamine. The COS produced is of the partially acetylated COS (paCOS) type, which still contains an acetyl group. The degree of deacetylation is a significant factor in the resulting COS product, COS with the fully deacetylated COS (fdCOS) type of chitosan with a high degree of deacetylation. Other factors to consider are the raw material of chitosan, the incubation time, the screening process, and the production of microorganism cultures.

The study addresses the management of kitchen waste by transforming it into biofertilizer formulations utilizing an effective in-house developed multi-enzyme preparation. A separate hydrolysis and fermentation bioprocessing approach which in particular relates to the application of a separate enzyme preparation from Aspergillus niger P-19 to separately hydrolyze kitchen waste, followed by the growth of Klebsiella pneumoniae AP-407 in the liquid hydrolysate as well with simultaneous production of carrier-based biofertilizer. In liquid and carrier-based biofertilizers, the viable cell count reaches 3.00 × 1012 CFU/ml and 3.00 × 1012 CFU/g, respectively. The current study adopts a novel process technique for the manufacturing of both carrier and liquid biofertilizers, adopting a zero-waste approach to the management of kitchen waste.

Iron and chromium based alloys have found wide application in various fields of science and technology. Primary carrier based on Fe-Cr-Al alloy is used in block catalysts for high-temperature hydrocarbon conversion, in production of block metal catalysts for neutralization of toxic gases released during operation of internal combustion engines, as well as those present in smoke emissions from enterprises. Influence of thermal action on Fe-Cr-Al alloy foil and stability of secondary carrier on its surface was studied. Elemental composition of the surface layer of X15U5 alloy foil does not remain constant during heating and depends on the thermal treatment mode. Some of the elements come to surface and elemental composition of surface layer can differ significantly from that observed in the bulk of foil sample. This implies the possibility of changing the adhesive and adsorption properties of the foil surface, as well as the need to take this fact into account when supporting a secondary carrier and active phase to the foil. Applied technique of phosphating and supporting a secondary carrier to the foil surface makes it possible to obtain a sufficiently stable coating. There is no shedding of the secondary carrier from foil surface during high-temperature treatment in air.

In South Korea, demolition waste (DW) management has become increasingly significant owing to the rising number of old buildings. Effective DW management requires an efficient approach that accurately quantifies and predicts the generation of DW (DWG) of various types, which necessitates access to the required information or technology capable of achieving this. Hence, we developed an artificial intelligence-based model that predicts the generation of ten DW types, specifically from buildings in redevelopment areas. We used an artificial neural network algorithm with < 10 neurons in the hidden layer to derive individual input variables and optimal hyperparameters for each DW type. All DWG prediction models achieved an average validation and test prediction performance (R²) of 0.970 and 0.952, respectively, with their ratios of percent deviation ≥ 2.5, ver-ifying them as excellent models. Moreover, a Shapley additive explanations analysis revealed that DWG was most impacted by the floor area for all the DW types, with a positive correlation with DWG. Conversely, other factors showed either a positive or negative correlation with DWG de-pending on the DW type. The study findings will enable demolition companies and local gov-ernments in making informed decisions for efficient DW management and resource allocation by accurately predicting the generation of various types of DW.

Sherubtse College under Royal University of Bhutan has a total of 1582 students, where 787 0f them are female. They suffer from menstrual and menstrual cramps every month and they use napkins to stay clean and healthy. As all the college girls are educated on the norms and use of sanitary napkins, the proper management of the waste generated is lacking. The disposal of used sanitary napkins and management is a challenge to the college management. This small research aims to investigate on how girls in college campus manage the menstural waste and the amount of sanitary napkins used. The lack of proper dumping areas leads to the improper sanitary waste management and sometimes the waste generated from the sanitary napkins are toxic and unhealthy. It is very important to initate some ways to dump the pads and its related problem should be seriously addressed by the college management. It is also important to come up with different soultion and management of these wastes for sustainable environment. Therefore, this research will be mainly mentioning about the suggestions and how the sanitary waste is being managed in Sherubtse College campus and the amount of sanitary pads used in a month or an year.

Using machine learning or deep learning to solve the problem of garbage recognition and classification is an important application in computer vision, but due to the incomplete establishment of garbage datasets and the poor performance of complex network models on smart terminal devices, the existing garbage classification models The effect is not good.This paper presents a waste classification and identification method base on transfer learning and lightweight neural network. By migrating the lightweight neural network MobileNetV2 and rebuild it, The reconstructed network is used for feature extraction, and the extracted features are introduced into the SVM to realize the identification of 6 types of garbage. The model was trained and verified by using 2527 pieces of garbage labeled data in the TrashNet dataset, which ultimately resulted in a classification accuracy of 98.4% of the method, which proves that the method can effectively improve the classification accuracy and time and overcome the problem of weak data and less labeling. The over-fitting phenomenon encountered by small data sets in deep learning makes the model robust.

Derelict asbestos mine sites in South Africa pose a considerable risk to human, environmental and socio-economic health. Comprehensive mineralogical and geochemical datasets for the existing hazardous geological materials still exposed in Southern African derelict asbestos mines remain largely non-existent, as very little published and up-to-date literature is available. In this study three representative types of asbestos mineral fibres from derelict asbestos mines in Southern Africa, namely chrysotile from Havelock mine, amosite from Penge mine and crocidolite from Prieska mine are characterized mineralogically and geochemically to critically evaluate real-life hazards in rural and asbestos-fibre contaminated regions. The samples were examined using polarising light microscopy, X-ray fluorescence (major and trace elemental analysis), X-ray diffraction (including Rietveld refinement), specific surface area analyses and bio-durability tests. Data are discussed in view of their potential toxicities on both human health and the environment in the context of developing countries. Finally, information on the mineralogical and geochemical status of asbestos mine waste and its importance as baseline data for rehabilitation considerations is also evaluated.

The global demand for rubber is on a steady rise, which is driven by the increasing production of automobiles and the growing need for industrial, medical, and household products. This surge in demand has led to a significant increase in rubber waste, posing a major global environmental challenge. End-of-life tire (ELT) is a primary source of rubber waste, which possesses significant environmental hazards due to its massive stockpiles. While landfilling is a low-cost and easy-to-implement solution, it is now largely prohibited due to environmental concerns. Recently, ELT rubber waste has garnered considerable attention for its potential applications in civil engineering and construction. These applications not only enhance sustainability but also foster a circular economy between ELT rubber waste and the civil engineering and construction sectors. This review article concentrates on the recent research progress and challenges in the civil engineering applications of ELT rubber waste. It also discusses commercially available recycled rubber-based construction materials, their properties, testing standards, and certification. To the best of the authors' knowledge, this is the first time such a discussion on commercial products has been presented.

The predominant management approach for municipal solid waste (MSW) remains disposal, given significant increases in generation and disposal rates of MSW in recent decades. In addition to the well-documented carbon emissions from disposal sites, these sites accumulate numerous elements, the masses of which are substantial globally yet inadequately quantified. The unique combinations of waste constituents, elements, diverse environments, and confined spaces in disposal sites create distinct biogeochemical conditions, setting them apart from any other infrastructure or geological feature on Earth. This review first presents a global summary of the cumulative masses and disposal rates of MSW constituents and associated elements. The five dominant transformation and transport processes influencing disposed elements are examined: biochemical degradation, physicochemical transformation, gas migration, leachate migration, and solid spillage. The magnitudes and rates of the processes corresponding to major disposed elements, including carbon, nitrogen, sulfur, chlorine, and several metals, are systematically summarized. We examine and quantify the potential environmental impacts and health risks associated with element transformation and transport. We also explore the existing knowledge and techniques for resource recovery and site remediation of disposal sites. The distilled compilation of measurements and insights herein serves as a valuable primer for researchers, practitioners, and decision-makers involved in MSW management.

With an increasing demand for quality of care and lower costs, hospitals are looking for industry-based methods to improve efficiency in their processes. This study aims to reduce waste in a public hospital in Mexico by improving the medical supply process for the operating room. To this end, a lean healthcare (LH) implementation following the DMAIC approach (Define-Measure-Analyze-Improve-Control) is carried out. We analyze the value stream of the supply process, including main surgical procedures and their related medical supplies, and identify different causes of inefficiency, which are evaluated and controlled through different tools, including a value stream map, Kanban, and the 5S program. As a result, five types of waste were reduced. Over-processing requests were reduced by 15.3%, defective identification numbers were reduced by 46.5%, redundant processing was improved by 94.8%, near 2.8% of the unnecessary inventory was reduced, and transportation waste was reduced by up to 16.7%. Finally, the lead-time for the main supplies was reduced by 33 days. This work demonstrates that LH and DMAIC are effective in reducing waste and are highly conducive to improving sustainability in healthcare processes. Moreover, it provides practical insights for practitioners regarding the implementation of LH in public hospitals in developing countries.

Abundant animal manure in livestock areas has the potential to be used as organic fertilizer which can restore soil fertility by turning it into compost and biochar. The goal of this study was to as-sess how well soil fertility and red chili yield might be increased by using biochar and poschar made from various animal wastes. In this investigation, a factorial pattern and randomized block design were used. The first factor was the biochar treatment type, which included no biochar, biochar made from cow manure, biochar made from goat manure, and biochar made from chicken manure. The second factor was the type of poschar, which included no poschar, poschar made from cow manure, poschar made from goat manure, and poschar made from chicken manure. The findings of this study suggest that using biochar in conjunction with poschar can significantly improve soil parameters such as soil water content, pH, EC, humic acid, fulvic acid, C, N, P, K, and CEC. Red chilies grow and yield more per hectare when different types of biochar and poschar are used. The use of biochar from cow manure together with poschar from chicken manure shows the best agronomic effectiveness.

Spent nuclear fuel and high-level radioactive waste can be disposed in deep horizontal drillholes in sedimentary, metamorphic, or igneous rocks. Horizontal drillhole disposal has safety, operational, and economic benefits: The repository is deep in the brine-saturated zone far below aquifers in a reducing environment of formations that can be shown to have been isolated from the surface for millions of years; its depth provides safety against inadvertent intrusion, earth¬quakes, and near-surface perturbations; it can be placed close to the reactors and interim storage facilities, minimizing transportation; disposal costs per ton of waste can be kept substantially lower than for mined repositories by its smaller size, reduced infrastructure needs, and staged imple¬mentation; and, if desired, the waste could be retrieved using “fishing” technology. In the proposed disposal concept, corrosion-resistant canisters containing unmodified fuel assemblies from commercial reactors would be placed end-to-end in up to 50 cm diameter horizontal drill¬holes, a configuration that reduces mechanical stresses and keeps the temperatures below the boiling point of the brine. Other high-level wastes, such as capsules containing 137Cs and 90Sr, can be disposed in small-diameter drillholes. We provide an overview of this novel disposal concept and its technology, discuss some of its safety aspects, and compare it to mined repositories and the deep vertical borehole disposal concept.

The construction of reinforced concrete (RC) structures inevitably consumes an excessive number of rebars, leading to significant cutting waste and carbon emissions. Extensive research has been conducted to minimize this issue and its consequences; however, these methods consistently consume a substantial number of rebars. This includes a previous study that utilizes the lap splice position optimization and special-length rebar concept without considering the lapping zone regulation. Moreover, conventional lap splices pose inherent drawbacks that could jeopardize the structural integrity of RC members. In contrast, mechanical couplers eliminate the need for rebar lapping, effectively reducing rebar consumption. This research aims to evaluate the impact of an integrated mechanical coupler and special-length-priority minimization algorithm on the reduction in rebar consumption and cutting waste in RC columns, achieving near-zero cutting waste. To validate the effectiveness of the proposed algorithm, it was applied to the column rebars of an RC building. The results revealed a significant reduction in ordered rebar consumption by 18.25%, accompanied by substantial reductions in cutting waste (8.93%), carbon emissions (12.99%), and total costs (10.81%) compared with a previous study. The outcomes provide the industry with insights into further reducing rebar consumption and its related consequences. Applying the proposed algorithm to various construction projects will further amplify the corresponding benefits.

Acerola (Malpighia spp.) is a tropical plant genus of shrubs and trees whose fruit is rich in nutrients and bioactive compounds. However, its production generates significant waste that could pose an environmental issue. This review aims to summarize recent research on the potential uses of acerola wastes, including the extraction of bioactive compounds such as polyphenols, carotenoids, and pectins, as well as the development of materials such as nanomaterials, chitosan, and biofuels. Additionally, the paper discusses the potential medical applications of acerola wastes, such as wound healing, antioxidant, and anticancer effects. Finally, the paper explores the challenges and opportunities of using acerola waste as a sustainable source of raw materials and energy. The findings suggest that acerola waste could be a valuable resource for developing high-value products and promoting sustainable production practices in the fruit industry.

Millions of tons of wool waste are produced yearly by textile industries, which may become a serious environmental hazard in the near future. Given this concern, it is crucial to explore strategies to reduce the amount of wool waste generated worldwide and adopt more sustainable practices for dissolving and regenerating wool keratin (WK) from textile waste. Most traditional methods involve the use of expensive, toxic, harmful, and poorly biodegradable compounds. To overcome these limitations and facilitate the reuse of wool waste through a cascade valorization strategy, researchers have started testing the use of deep eutectic solvents (DES) as a more sus-tainable and eco-friendlier alternative for WK dissolution and regeneration. In this study, the potential of two different DES mixtures, Choline chloride (ChCl): Urea and L-Cysteine (L-Cys): Lactic acid (LA), was explored for dissolving wool waste. Subsequently, the obtained gels based on DES-WK were blended with polyvinyl alcohol (PVA) in different ratios to produce nanofibers using the electrospinning technique. The effect of pH and the properties of the electrospinning solutions, namely electrical conductivity and viscosity, on the morphology of the gel solutions were evaluated. Moreover, the morphological features of the produced gel-based electrospun PVA/DES-WK nanofibrous membranes were analyzed using scanning electron mi-croscopy (SEM). Additionally, the PVA/L-Cys: LA DES-WK, which proved to be the most effective DES mixture for fabricating WK gel-based nanofibers, were characterized through Fourier transform infrared spectroscopy (FTIR) and tensile tests. Furthermore, their antioxidant and an-timicrobial abilities were evaluated. The results obtained revealed that this approach to valorize textile waste offers a unique avenue for the development of sustainable functional materials with potential applications in various biomedical and industrial fields.

Sharing the same raw material, recycling and composting are in direct conflict with incineration of municipal solid waste in combined heath and power plants. Indeed, waste-to-energy plants in regions with high recycling rates import urban waste from other countries to use otherwise unused capacity, and raise revenues. Using the case of Italy’s second largest and economically most developed region, I discuss the economic viability of municipal solid waste incineration to produce electricity and heath in the context of the increasing role of electricity production from renewable energy sources as well as of the emerging mass-scale uptake of bioplastics. Four lessons and three guidelines aimed to local authorities and policy makers emerge from the present study.

Quarry waste fines and eggshells are unavoidable wastes which relentlessly contribute to environmental load and pollution. Although a number of studies have suggested various methods for recycling, these wastes remain underutilized due to some technical constraints. In addition, no study has yet been explored on the possibility of combining quarry waste fines (QWF) and eggshell powder (ESP) for tobermorite synthesis. Tobermorite is the main component which primarily provides strength to the autoclaved aerated concrete products. For this purpose, this study seeks to evaluate the potential of QWF- ESP mix at 10%, 15% and 20% amounts of cement, respectively. The XRF, XRD, and TGA–DTA techniques were used to characterize the waste materials while physical and mechanical property tests and XRD analysis were performed on the autoclaved samples. It was found that QWF contains 53.77% SiO2, while ESP contains 97.8% CaO which are key components for tobermorite synthesis. This study also revealed that the mixture with only 10% cement has the highest compressive strength among the QWF-ESP samples. Furthermore, the formation of tobermorite in the samples was confirmed through XRD analysis. Hence, the hydrothermal curing of QWF –ESP can be further developed to produce functional tobermorite – bearing materials.

This article aimed to evaluate, using statistical tools, the generation and composition of urban solid waste (MSW) in the city of Belém, Pará, from nine urban collection sectors in the municipality, and the average nominal income of the population. Approximately 900kg of urban solid waste were col-lected from the municipality in the period from 2021 to 2022. Statistical tests were carried out on hypotheses with 5% significance in comparative evaluations, and their respective average nominal incomes. The results indicated that the organic fraction corresponds to 55.57% of the waste generated in the municipality, 14.26% is inert waste (potentially contaminating) and 0.67% is miscellaneous waste. It was observed that the waste generated by families with high purchasing power tends to contain higher percentages of recyclables, while in families with lower purchasing power the highest percentages tend to be organic. Knowledge of the generation of MSW is fundamental for the choice and dimensioning of operations and processes involved in the management chain at the municipal level. The decentralization of services offered based on solid waste management would enable greater success in serving the population.

The volume of electronic waste (e-waste) received in Nigeria is reportedly on the increase and the effects on environmental health are yet to be fully ascertained. This study aimed to investigate haematological indices, lead and serum iron levels in workers occupationally exposed to electronic wastes in South-South, Nigeria. In this pilot study, 104 participants were enrolled from Benin City, South-South Nigeria; consisting of 63 E-waste Workers (EW) sex- and aged-matched with 41 Unexposed Participants (Control). Blood levels (5 mL) of the metals (lead and iron) were determined using Inductively Coupled Plasma-Mass Spectrometry while the haematological parameters [white blood cells (WBC), Lymphocytes ( LY); monocytes (MO), granulocytes(GR), red blood cells (RBC), haemoglobin (Hgb), haematocrit (HCT), mean cell volume (MCV), mean cell haemoglobin (MCH), mean cell haemoglobin concentration (MCHC) and platelets (PLT)] were determined using standard methods. Results obtained from this study show a significantly low serum iron (11.5 ± 2.14 µg/dL) in the EW compared with Control (168.9 ± 2.39 µg/dL); while blood lead level in EW (1.07±0.02 µg/dL) was significantly elevated compared with Control (0.72 ± 0.12). Total WBC and RBC, HCT, MO and MCV were all significantly elevated in EW compared with Control while LY and PLT in the EW were significantly decreased compared with Control. This study concludes that chronic occupational e-waste exposure may increase blood lead level, lower serum iron status and may have adversely altered some important haematological parameters in the studied population.

Is the production of the “AnchoisFert” organic fertilizer via the circular economy process based on omega-3 lipid extraction of milled anchovy fillet leftovers with citrus limonene followed by mild drying economically and technically viable? This study answers this question and identifies the main obstacles, chiefly of economic and organizational nature, to be overcome prior to commercialization of this new organic fertilizer. Along with non-variable and proven efficacy, successful competition with conventional organic and inorganic fertilizers requires affordable cost and regular supply. This, inter alia, requires to establish new and mutually beneficial relationship between bioeconomy firms and fish processing companies.

Cyanides, though naturally occurring, are environmental pollutants when not treated properly. Some methods used to attenuate cyanides in waste waters from industrial processes are based simply on changing the physico-chemical properties of the waste water such as the pH and temperature. The effectiveness of these methods are based on hydrolysis of the cyanide and volatilization of the hydrogen cyanide formed. Another reaction which takes place simultaneously is ultraviolet-catalysed oxidation which converts the cyanide to bicarbonates and carbonates.The changes in the cyanide degradation rate approaches a minimum faster if the cyanide solution is maintained at a higher than ambient constant temperature.

The world’s population is growing at a rapid pace, thus increasing the need for shelter, which, because of increased carbon emissions, is making our planet less inhabitable. Thus, supplementary cementitious materials (SCMs) are used to reduce the embodied carbon emissions in the building sector. Wood ash, as a replacement for cement in soil treatment, seems to be a promising material. In this study, we considered the strength, stiffness, and microstructural behavior of marine clay treated with cement and wood ash as a cement replacement. Since clay is abundant in nature, it could help stabilize waste to improve the mechanical behavior of produced composites. Portland cement (7%, 10%, and 13%) was replaced with various amount of wood ash (5% and 10%) with two different dry densities (1400 and 1600 kg/m3) and three distinct curing periods (7, 28, and 60 days). Unconfined compressive strength, direct shear, porosity, pulse velocity, x-ray diffraction, and scanning electron microscopy tests were performed on selected specimens to evaluate the structural and microstructural effect of clay–wood ash–cement interaction. The results revealed that the replacement of cement with 5% of wood ash yielded superior performance. The microstructure investigation of wood ash–cement–clay blends further showed the formation of a densified matrix with stable bonds. Furthermore, the porosity and strength properties of blends developed unique relationships, which were further confirmed by other supplementary materials and soils.

Background: Food waste has been a major social problem in recent years. Annually, 1.3 billion tons of food is wasted worldwide. It is recommended that food waste should be reduced at every stage of production. By-products from food processing have high nutritional value; therefore their use in the design of new products is advisable. Methods: By-products from tomato processing (tomato waste-TW) and pepper (defatted pepper seeds-DPS, pepper placenta-PP) were used at a level of 10-30% to produce extruded pasta. The farinographic characteristics, chemical composition, cooking quality, and color of the pasta were studied. Results: The results showed a significant up to 27% increase in the protein content in the TW30 samples, compared to the control. The TDF content increased over five times in DPS30 and TW30 (27.99% and 25.44%). The amino acid composition of the pasta improved with the fortification, but failed to achieve the complete protein by FAO. The DPS30, PP20, PP30, and all TW samples can be considered high-protein products according to the EU definition (min. 20% energy from protein). Conclusion: Vegetable waste can be a valuable additive for improvement of the nutritional value of food. Their addition is part of the zero-waste trend, which has a positive impact on the environment.

A shrimp oil rich in omega-3 lipids and carotenoids is obtained in remarkably high 5 wt% yield extending to pink shrimp processing waste (head and carapace) the circular economy approach to extract fish oil from fish processing by-products using d-limonene. Biobased limonene, a powerful antimicrobial and antioxidant agent, is an excellent solvent for both lipids and astaxanthin-based carotenoids preventing oxidative degradation during the extraction cycle including solvent and oil separation at 85°C. A new low cost route is established to extract valued marine oil from biowaste annually made available in over 2.2 million tonnes.

COVID-19 greatly challenges human beings in the health sector and leaves behind a large amount of medical waste that poses many potential threats to the environment. In this paper, we compiled relevant data released by official agencies and the media, and conducted data supplementation based on previous studies to calculate the net value of medical waste production in Hubei Province during COVID-19 with the help of a neural network model. Then, we reviewed the data related to the environmental impact of medical waste per unit and designed four scenarios to estimate the environmental impact of new medical waste generated during the epidemic. The results showed that at a medical waste generation rate of\ 0.\ 5\ kg/(\ bed\ \cdot\ d) COVID-19 resulted in a net increase in medical waste volume of about 3366.99 tons in Hubei Province. In the four scenario assumptions, if the medical waste brought by COVID-19 is completely incinerated, it will have a large impact on the air quality. If it is disposed by distillation sterilization, it will produce a large amount of wastewater and waste residue. Based on the results of the study, three policy recommendations are proposed in this paper: strict control of medical wastewater discharge, reduction and transformation of the emitted acidic gases, and attention to the emission of metallic nickel in exhaust gas and chloride in soil. These policy recommendations provide a scientific basis for controlling medical waste pollution.

Pyrolysis has been applied in the human economy for many years, and it has become a significant alternative to the production of chemical compounds, including biofuels. The article focuses mostly on recent achievements in the technical and processing aspects of pyrolysis. This review provides an overview of the recent advanced pyrolysis technology used in gas, bio-oil, and biochar production. The key parameters to maximize the production of specific chemical compounds were discussed and considered during the construction of the reactors. The emphasis is put on optimizing the process parameters, technical requirements, and renewable energy use in the process and conception to improve the efficiency of product production. The application of pyrolysis gas, oil, and biochar as valuable chemical compounds are related to the intensifying effects of climate change, biofuel production, and waste management in accordance with the principles of sustainable development.

In this study, 12 organic waste materials were subjected to TG/DTG thermogravimetric analysis and DSC calorimetric analysis. These analyses provided basic information about thermochemical transformations and degradation rates during organic waste pyrolysis. Waste materials were chosen to cover the most abundant waste that can be found in the municipal solid waste stream. Based on TG results, kinetic parameters according to Coats–Redfern method were determined. The pyrolysis activation energy was the highest for cotton 134.5 kJ∙(mol∙K)-1 and the lowest for leather 25.2 kJ∙(mol∙K)-1. The DSC analysis showed number of transformations occurred during pyrolysis for each material. For each transformation, normalized energy required for transformation, or released during transformation were determined and then summarized to present energy balance. The study found that only for three waste materials: PET (-220.1 J⸱g-1), leather (-66.9 J⸱g-1), and chicken meat (-130.3 J⸱g-1) energy balance was negative, while the highest positive balance value was found for potato peelings (367.8 J⸱g-1). The obtained results may be applied for the modelling of energy and mass balance of municipal solid waste pyrolysis.

The circular economy (CE) has emerged as a viable alternative for tackling the problems caused by rising consumption, including solid waste (SW). The present study conducted a meta-analysis of research published between 2012 and 2022 on CE and solid waste management (SWM). A bibliometric analysis was used from the Web of Science (WoS) and Scopus databases. By studying the articles, we briefly discussed the connections between them and how one contributes to the evolution of the other. Some findings point to greater collaboration between Italy and Bolivia, followed by China and Malaysia. However, they move away from the traditional axes as the United States and Canada. In addition, it was found that the adoption of reuse and selective collection, in fact, allow the reduction of the volume of discarded materials. In this way, it was possible to conclude that a greater connection between CE and GRS makes it possible to optimize the useful life of landfills through the treatment of organic waste and recycling, to encourage waste picker cooperatives and selective collection programs, and to reduce the financial costs of the system as a whole, making it more durable and sustainable.

The production, processing of agricultural products results in massive generation of waste, which has an environmental impact. In current study on the node of valorisation of the processed waste, orange and banana peel waste are utilized for the production of biscuits. The fortified biscuits were analysed for proximate and sensory analysis. The fibre content of the fortified biscuits increases several folds. From the sensory score the proportion of biscuits with 7.5% and 10% has undesirable quality parameters, whereas up to 5% concentration all the parameters are more desirable. Fortifying biscuits with orange and banana peel powder may be an excellent source of dietary fibre and an enhanced valorisation technique.

Today is the era of nanoscience and nanotechnology, which finds applications in the field of medicine, electronics, or environmental cleanup. Even though the nanotechnology is in its emerging phase, but still it provides solutions to numerous challenges. Nanotechnology and nanoparticles are found very effective because of their unique chemical and physical properties, high surface area, but their high cost is one of the major hurdles in its wider application. So, the synthesis of nanomaterials especially 2D nanomaterials from the industrial, agricultural and other biological activities could provide a cost-effective technique. The nanomaterials synthesized from such waste not only minimizes the pollution but also provides an eco-friendly approach towards the utilization of the waste. In the present review work, the emphasis has been given on the types of nanomaterials, different methods for the synthesis of 2D nanomaterials from the waste generated from industries, agriculture and their application in electronics, medicine and catalysis.

Continuity of activities and projects are important for sustainably developing organizations, especially universities. The purpose of this research study is to find university development guidelines regarding waste management according to the green university ranking criteria for sustainable developments by studying and collecting the data covering the last five years (2019 - 2023) of Mahasarakham University. We also analyzed and synthesized lessons learned from the details of the operations and the factors involved in successes while comparing and providing suggestions for the operations in the next year. It was found that waste management that resulted in continuous developments that achieved the goals of Mahasarakham University consisted of the five guidelines. (1) Making green university policies and using them as the (key performance index) KPI of the divisions and also announcing the university's waste management policies by applying the principles of 3R (Reuse-Reduce-Recycle). (2) Allocating the budgets supporting the projects' activities according to the evaluation criteria. (3) Student and personnel participation as well as the mechanisms used by the committees from various administrative divisions such as Student Council, Student Association and clubs to drive the operations. (4) Identifying the main responsible individuals and committees for the green university who communicated and drove the operations while collecting, analyzing and preparing the data. (5) Follow-ups and evaluations of the project's activities with the Plan-Do-Check-Act (PDCA) processes for continuous and sustainable developments and improvements leading to the green university. With the above operations, Mahasarakham University's waste management scores of the six indices during 2019 - 3023 increased annually as follows: 900, 900, 1050, 1275 and 1350.

Objective: The aim of this study is to explore what inside the lipid lump obtained from skin. Try to understand the reasons for these physiological functions. In this paper, the lipid droplets or lumps was aimed to shed light on, figuring out what kind of cracks from metabolism were embedded inside. Results: A novel method was introduced for the detection of pathogens within lipid droplets extracted from acne or inflamed pores, as well as normal pores, using microscopic analysis. Through this technique, the presence of cracks from our body within these lipid droplets were identified. Methods: Observations were conducted using a microscope, with samples placed on slides and grind like blood smear. To enhance the transparency of the samples, tween-20 was utilized. This reagent was first time to be used for observing such big lipid lump of skin secretion. The evidences were recorded using the DMi8 camera from Leica.

Nano-emulsions of essential oils (EO) and their chemical constituents are promising raw materials for the ecological control of Tribolium castaneum. Curcuma longa Linn is a plant known for the properties of its rhizome which is used in food, health and hygiene products. Its leaves are by-products with no commercial value, but with unexplored bioactive volatile constituents. This study aims to evaluate the repellency of nano-emulsions containing the EO from leaves of C. longa or its three main chemical constituents against T. castaneum. The representative mixture of EO extracted in four different months showed p-cymene (26.0%), 1,8-cineole (15.1%) and terpinolene (15.5%) as major compounds. Nano-emulsions of EO (HLB 16.7), terpinolene (HLB 15.0), 1,8-cineole (HLB15.0) and p-cymene (HLB 15.0) were repellent at concentrations of 11 μg/cm2 (EO, terpinolene and p-cymene) and 1.1 μg/cm2 (1,8-cineole). The EO nano-emulsion droplet size increased linearly over time, remaining below 300 nm for 35 days and below 600 nm for 80 days. The EO nano-emulsion proved to be a green alternative to synthetic pesticides, as it was safe against the bioindicator Chlorella vulgaris. Terpinolene, 1,8-cineol and p-cymene were able to inhibit the enzyme telomerase from T. castaneum in an in silico assay, which may explain the repellency of these samples. This study provides ideas for the utilization of EO from leaves of C. longa as raw material of new environmentally friendly plant-derived nanobiopesticides.

This study aimed to investigate the effect of reducing the amount of organic waste on the weight of cats in Tehran. The weight of 4192 cats was measured from spring 2016 to the end of winter 2020. They were classified into 6 age groups, 2 gender groups, and 13 geographical areas. Their weight was measured for 48 months (16 seasons). The statistical parameters analysis showed no weight loss in 2017, but since 2018, cats have been losing weight every year. They had lost about 178g of their weight in 2018. The sharpest annual decrease was observed in 2019 when about 301g of weight loss was recorded. In the winter of 2020, 115g of weight loss took place. In the spring of 2017, no weight change was observed, but in the spring of 2018, the cats lost 155g of their weight. Their weight loss intensified in the spring of 2019 and about 299g of weight loss was observed. In the summer of 2017, as in the spring of the same year, no weight loss was recorded, but for the summer of 2018, the weight loss was evident and about 205g of the weight of the cats had been reduced. The weight loss in the summer of 2019 not only continued but intensified and about 304g of weight loss was recorded for cats. Weight change was not observed in the fall of 2017 as in the spring and summer of the same year. In the fall of 2018, weight loss was recorded for cats. They had lost about 324g of their weight in the fall of 2018. Also, they experienced a weight loss of about 218g in the fall of 2019. During the spring, summer, and autumn of 2017, no weight loss was observed in the cats for the winter of 2018, but in the winter of 2019, the cats faced the most severe weight loss (seasonally). They lost about 401g of weight in the winter of 2019. Of course, in the winter of 2020, about 186g of weight loss was observed in cats. The results showed that female cats did not lose weight in 2017 but experienced weight loss in 2018 with a weight loss of 181g. The weight loss of females intensified in 2019 and 294g of weight loss was recorded. Female cats lost 186g of their weight in the winter of 2020. Male cats did not lose weight like female cats in 2017. But in 2018, a weight loss of 166g was observed in male cats. The weight loss of male cats continued in 2019 and 311g of weight loss was recorded for them. However, in 2020, unlike females, weight loss was not observed in male cats. It can be said that both sexes lost more weight in the winter of 2019 than in other seasons. In 2017, weight loss was observed only for the region of 10, and in the same year, weight gain was recorded for the region of 15. But in 2018, except for regions 3, 4, 15, and 19, weight loss was observed in other regions. In 2019, the weight loss of cats spread and weight loss was observed in all regions except the region of 12. In winter 2020, weight loss was recorded only in the region of 4. In the end, it can be concluded that the weight of cats has decreased since the spring of 2018 because the beginning of the decrease in the amount of organic waste has been recorded since the winter of 2018. So, there is a direct relationship between the weight of cats and the amount of organic waste (access to food). The amount of garbage has been decreasing since the winter of 2018, and the average weight of cats has also been decreasing since the spring of 2018 due to the decrease in access to food.

Forest recreation can be successfully used for the psychological relaxation of respondents and can be used as a remedy for common problems with stress. The special form of forest recreation intended for restoration is forest bathing. These activities might be distracted by some factors, such as viewing buildings in the forest or using a computer in nature, which interrupt psychological relaxation. One factor that might interrupt psychological relaxation is the occurrence of an open dump in the forest during an outdoor experience. To test the hypothesis that an open dump might decrease psychological relaxation, a case study was planned that used a randomized, controlled crossover design. For this purpose, two groups of healthy young adults viewed a control forest or a forest with an open dump in reverse order and filled in psychological questionnaires after each stimulus. A pretest was used. Participants wore oblique eye patches to stop their visual stimulation before the experimental stimulation, and the physical environment was monitored. The results were analyzed using the two-way repeated measures ANOVA. The measured negative psychological indicators significantly increased after viewing the forest with waste, and the five indicators of the Profile of Mood States increased: Tension-Anxiety, Depression-Dejection, Anger-Hostility, Fatigue, and Confusion. In addition, the negative aspect of the Positive and Negative Affect Schedule increased in comparison to the control and pretest. The measured positive indicators significantly decreased after viewing the forest with waste, the positive aspect of the Positive and Negative Affect Schedule decreased, and the Restorative Outcome Scale and Subjective Vitality scores decreased (in comparison to the control and pretest). The occurrence of an open dump in the forest might interrupt a normal restorative experience in the forest by reducing psychological relaxation. Nevertheless, the mechanism of these relevancies is not known, and thus, it will be further investigated. In addition, in a future study, the size of the impact of these open dumps on normal everyday experiences should be investigated. It is proposed that different mechanisms might be responsible for these reactions; however, the aim of this manuscript is to only measure this reaction. The identified psychological reasons for these mechanisms can be assessed in further studies.

Highlights: A new material with a bending strength higher than that of concrete was developed using vegetable or fruit waste. The new material maintains the color, taste, and flavor of the original vegetable or fruit. Without water resistant treatment, the material is edible and can be conditioned with seasonings

Biofuels have become an integral part of everyday life in modern society. Bioethanol and fatty acid methyl esters are a common part of both the production of gasoline and diesel fuels. Also, pressure on replacing fossil fuels with bio-components is constantly growing. Waste vegetable fats can be replacing biodiesel. HVO seems to be a better alternative. This fuel has a higher oxidation stability for storage purposes, a lower temperature of loss of filterability for the winter time, a lower boiling point for cold starts and other. Viscosity, density, cold filter plugging point of fuel blend, and flash point were measured to confirm that a fuel from HVO is so close to a fuel standard that it is possible to use it in engines without modification. The objective of this article is to show the properties of different fuels with and without HVO admixtures and to prove the suitability of using HVO compared to FAME. HVO can also be prepared from waste materials and no major modifications of existing refinery facilities are required. No technology in either investment or engine adaptation of fuel oils is needed in fuel processing.

As a hazardous waste, pickling waste liquor must be properly treated. An alternative consists in promoting the formation of ferrous salts from this residue, due to its higher ferrous content. Since FeCl2·4H2O is widely used in several applications, obtaining pure crystals of this material appears to be an interesting prospect. However, this compound has scarcely been investigated. In the present work, FeCl2·4H2O crystals have been obtained from pickling waste liquors. Their structural and morphological characteristics have been investigated by X-ray diffraction, scanning electron microscopy as well as Mössbauer spectroscopy. In addition, the photoluminescence study of the obtained samples was also assessed. It was observed that after some aging time, the obtained crystals change in colour from green to more yellowish. So, the aged sample has also been evaluated, and their structural characteristics are compared with the original crystals. Despite this, the obtained crystals exhibit a FeCl2·4H2O structure, which is not modified with the aging of the sample.

Understanding behavioral factors associated with obesity is of importance in addressing this issue. This study examined the association between cognitive restraint, uncontrolled eating, emotional eating and body mass index (BMI) and amount of food plated, consumed, leftovers, and leftover food thrown into the trash (food wasted) in early adolescent girls nine to 13 years in O’ahu, Hawai’i (n = 93). Food plated, consumed, leftovers, and food wasted were estimated using a three-day mobile food record (mFR). Weight and height were measured to compute BMI (kg/m2). The three-factor eating questionnaire provided a score from 0 to 100 for cognitive restraint, uncontrolled eating, and emotional eating. Higher scores are indicative of greater cognitive restraint, uncontrolled eating, and emotional eating. Pearson’s correlation and general linear models were computed to examine the relationship between three factor eating scores, BMI, and food plated, consumed, leftovers, and food wasted. There was no clinically significant association between cognitive restraint and amount of food wasted. Cognitive restraint was positively correlated with BMI (r=0.36, p<0.001) and with BMI z score (r=0.40, p<0.001). Uncontrolled eating and emotional eating were positively correlated with amount of leftover food at dinner (r=0.30, p=0.006; r=0.33, p=0.003, respectively). Emotional eating was positively associated with percentage of leftover food at dinner (r=0.24, p=0.30). Additional research should examine the specific roles of cognitive restraint, uncontrolled eating, emotional eating and food waste in the development of obesity in adolescents.

The accurate classification of landfill waste diversion plays a critical role in efficient waste management practices. Traditional approaches, such as visual inspection, weighing and volume measurement, and manual sorting, have been widely used but suffer from subjectivity, scalability, and labour requirements. In contrast, machine learning approaches, particularly Convolutional Neural Networks (CNN), have emerged as powerful deep learning models for waste detection and classification. This paper analyses VGG-16, InceptionResNetV2, DenseNet121, Inception V3, and MobileNetV2 models to classify real-life waste when trained on pristine and unadulterated materials, versus samples collected at a landfill site. When training on DiversionNet, the unadulterated material dataset with labels required for landfill modelling, classification accuracy was limited to 49.69% in the real environment. Using real-world samples in the newly formed RealWaste dataset showed that practical applications for deep learning in waste classification is possible, with Inception V3 reaching 89.19% classification accuracy on the full spectrum of labels required for accurate modelling.

Solid spent nuclear fuel from nuclear power plants has 3.4% fission products (80-160amu), contributing to over 99.8% radioactivity. On the other hand, liquid high-level radioactive waste (HLRW) from spent fuel reprocessing has 98.9% bulk elements (0-60amu) with 0.1% radioactivity. A separation mechanism on the mass categories as groups presents unique opportunities in managing HLRW for the long term with a considerable cost reduction. This paper proposes a thermal plasma-based separation system incorporating atmospheric pressure plasma torches for HLRW mass separation into low-resolution mass groups. Several engineering issues, such as waste preparation, waste injection into the plasma and waste collecting after mass separation, need to be addressed. Using COMSOL Multiphysics simulation, the generic system can be studied using noble gas mass separation and further analyze the mass filter capabilities. This paper provides the history of plasma-based mass separation. Functional modelling of a thermal plasma mass separation system is proposed under atmospheric pressure. Finally, aspects of mass separation simulation using noble gas Argon and Helium inside the plasma mass separation system were studied in COMSOL Multiphysics.

Waste orange peel represents a heavy burden for the orange juice industry, estimated in several million tons per year worldwide; nevertheless, this by-product is endowed with valuable bioactive compounds, such as pectin, polyphenols and terpenes. The potential value of the waste orange peel has stimulated the search for extraction processes, alternative or complementary to landfilling or to the integral energy conversion. This study introduces controlled hydrodynamic cavitation processes, as a new route to the integral valorization of this by-product, based on simple equipment, speed, effectiveness and efficiency, scalability, and compliance with green extraction principles. Waste orange peel, in batches of several kg, was processed in more than 100 L of water, absent any other raw materials, in a device comprising a Venturi-shaped cavitation reactor. The extractions of pectin, endowed with a very low degree of esterification, polyphenols (flavanones and hydroxycinnamic acid derivatives), and terpenes (mainly d-limonene) were effective and fast (high yield, few min of process time), as well as the biomethane generation potential of the process residues was effectively exploited. The achieved results proved the viability of the proposed route to the integral valorization of waste orange peel, though wide margins exist for further improvements.

E-waste is considered the fastest-growing global waste stream and has become an emerging environmental challenge. The widespread usage of digital devices has generated a large amount of e-waste. According to the Ministry of Commerce, India annually generates ~14.5 lakh metric tons of e-waste and recycles only ~5 % of e-waste. Annually, the global production of e-waste has been expected to increase by 4–5 %. Advancements in IT and communication divisions have improved the usage of electronic equipment. Heavy metals such as (Pb), mercury (Hg), arsenic (As), tin (Sn), and organic chemicals such as polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons (PAHs), polybrominated biphenyls (PBBs), polybrominated dibenzo-p-dioxins (PBDDs), polybrominated diphenyl ethers (PBDEs) are subsequently released from e-wastes and contaminates soil and water sources. These toxic compounds are hazardous to human health and the environment. They are capable of entering various biological systems and causing alterations in respiratory functions of the lungs, DNA damage, impaired functioning of the thyroid, and increased risk of chronic diseases such as cancer and cardiovascular ailments. Such concerns raise the quintessential need to manage e-waste to prevent future hazards. This manuscript critically reviews the sources, health and environmental impact, disposal techniques, recycling, and regulation of e-waste.

The global food system has three recognized challenges: (a)increasing the availability of food consumption, (b) reducing food loss, and (c) reducing food waste. The increasing demand for food consumption, increasing quantity of food loss, and corresponding increase in food waste are resulting in serious health, aesthetic, social, economic, and environmental problems due to a lack of appropriate planning and management. Despite its importance, there is no clear, concise, and comprehensive definition of food consumption, loss, and waste. Generally, food consumption, food loss, and food waste are dealt with separately. This article presents a logically constructed ontological framework of food consumption, loss, and waste. It gives equal importance to all three aspects of global food management. The systematic ontological framework is general, and the analysis can be applied to any country. The framework deconstructs the combinatorial complexity of the problem and explicates the pathways to manage the consumption, loss, and waste. The ontological framework encapsulates 19*8*7*4*5*6 = 25,536 possible components of the challenge. A critical analysis based on available data using the framework will help to develop strategies to deal with the problem. It can help to discover the gaps and to find ways to bridge the gaps. It is novel to conceptualize food consumption, loss, and waste together.

Information and telecommunications technology (ITT) have expanded into many aspects of modern life and have positively affected human life even in the most remote areas of developing countries. The rapid growth in ITT has led to an improvement in the capacity of computers but simultaneously to a decrease in the product’s lifetime as a result of which increasingly large quantities of e-waste are generated annually. It contains hazardous components that if it is not properly managed, can have adverse environmental and health effects. The management of e-waste poses significant challenges in developing countries. Due to the lack of adequate infrastructure, e-waste is burned or dumped in open areas. Informal and inefficient recycling practices are generally employed which further exacerbate pollution and health risks. So, the implementation of e-waste management, adequate recycling, and waste disposal facilities have become crucial concerns. This article reviews the concept of e-waste generation, challenges, disposal, and its impact on human health & environment in detail.

Biowaste management is in the center of attention in recent years, due to the increased focus on Circular Economy practices. Recent management solutions promote exploration for small and medium scale processing and monitoring practices. In this context, two pathways of biowaste valorization are analyzed: composting and anaerobic digestion. This study focuses on energy production with the hydrothermal carbonization (HTC) of anaerobic residues from biogas production. Lesvos has numerous processing facilities and olive mills, and therefore Olive Mill Wastewater (OMWW) are the main biowaste streams in the island, along with olive tree pruning, the organic fraction of municipal solid waste and sludge from wastewater treatment facilities. Most studies present applications on specific types of biowaste, while this study aims to co-treat several biowaste streams. A holistic experimental set-up that combines aerobic and anaerobic treatment strategies was developed taking into consideration the hydrothermal treatment of AD digestate along with locally available biowaste, like OMWW, sludge etc. A main target objective is to investigate if solid fraction could have a high heating potential In addition, HTC was able significantly to reduce the COD of OMWW while resulting in hydrochars with increased heating values.

This article aims to investigate gaps in the law and policies on e-waste management in communi-ties of Thailand and suggests a guideline for improving, developing, and designing legal measures and state policies for more effective enforcement of the law on e-waste management in communities. The findings reveal that the currently applicable law of Thailand lacks effective approaches and rules for e-waste management. Also, there is not any implementation of key envi-ronmental principles for e-waste management in communities, such as the Polluter Pays Principle (PPP) that requires manufacturing companies to take part in being responsible for disposal ex-penses or the Public Participation principle that requires users, manufacturers, distributors, and government agencies to take parts in disposing e-waste. As a result, problems of e-waste in com-munities of Thailand have been continuously increasing. According to such problems, the authors suggest that legal measures on e-waste management in communities should be specifically de-signed by implementing key environmental principles as a basis in determining formats and guidelines of e-waste management, especially participation of all sectors that can help in solving and reducing e-waste in communities that is harmful to health, sanitation, and environment.

Modified aluminum slag (MAS) was applied as an adsorbent for Congo red (CR) prepared by the hydrothermal treatment of Ca (OH) 2. At 25 ℃, with a MAS dosage of 0.3g, initial CR concentration of 100 mg/L and initial pH=5, and the adsorption time was 40 min, the CR removal efficiency was 98.41%. The adsorption trend of CR conformed to the second-order kinetics, and the adsorption isotherm follows the Freundlich isotherm model. Compared with RAS, MAS has a larger pore volume and specific surface area. The mechanism of action of MAS on CR was the interaction between membrane diffusion and internal diffusion, and the adsorption rate during the membrane diffusion was the fastest.

Inorganic polymeric materials react slowly at room temperature and as a result usually require high-temperature curing. This study used the Arrhenius equation to analyze the correlation between curing temperature and curing duration during high-temperature curing. The test results show that optimal values exist for each alkali equivalent of the activator (weight ratio of Na2O/glass powder), curing temperature, and curing duration. Extending the curing duration and increasing the curing temperature have positive effects when the alkali equivalent is lower than the optimal value. However, over-curing results in invisible cracking in the specimens. Furthermore, despite exhibiting high strength initially, the strength of specimens gradually diminishes after standing in air. To ensure the durability of glass-based geopolymer, the curing temperature should not exceed 70℃, and the curing duration should be less than one day.

A field experiment was conducted on the farm of Abi Jarash in Agricultural Collage, different rates of olive solid waste and cow manure were used, as follows: (control, fresh olive solid waste 100%, fresh olive solid waste 75%+ cow manure 25%, fresh olive solid waste 50%+ cow manure 50%, fresh olive solid waste 25+ cow manure 75%, Fermented Olive Solid Waste 100%, Fermented olive solid waste 75%+ cow manure 25%, Fermented olive solid waste 50%+ cow manure 50%, Fermented olive solid waste 25+ cow manure 75%), wheat was seeded. The impact of fresh and fermented olive solid waste and cow manure on some chemical and fertility soil properties was studied. the olive solid waste treatment 100% which added had more effect on the organic matter, exchange capacity, nitrogen, phosphorus and potassium in soil, plant and productivity, after that the fermented olive solid waste 75% + cow manure, fresh olive solid waste 100% comparing with the control, the values of organic matter were (25% 2.73, 2.39) and the cation exchange capacity (21.76, 20.44, 19.38) and for phosphorus (303.3, 277.8, 171.8) mg / kg, while the values of potassium ​​were (303.3, 277.8, 171.8) mg / kg. In terms of plant content, the plant content of nitrogen, phosphorus and potassium were the same as for grains (2.784, 2.606, 2.126), (0.4535, 0.4226, 0.2753), (1.876, 1.762, 1.234) respectively, (0.2875, 0.2016) respectively for the same previous treatments and elements. olive solid waste 100% was the highest productivity comparing with the other treatments, where the productivity of wheat was (9.513) ton. ha-1.

The green biomass of horticultural plants contains valuable secondary metabolites (SM) which can potentially be extracted and sold. When exposed to stress, plants accumulate higher amounts of these SMs, making the extraction and commercialization even more attractive. We evaluated the potential for accumulating of the flavones cynaroside and graveobioside A in leaves of two bell pepper cultivars (Mavras and Stayer) when exposed to salt stress (100 mM NaCl), UVA/B excitation (UVA 4-5 W/m²; UVB 10-14 W/m² for 3 hours per day) or a combination of both stressors. HPLC analyses proved the enhanced accumulation of both metabolites under stress conditions. Cynaroside accumulation is effectively triggered by high-UV stress, whereas graveobioside A contents increase under salt stress. Highest contents were observed in plants exposed to combined stress. Effects of stress on overall plant performance differed significantly between treatments, with least negative impact on aboveground biomass found for high-UV stressed plants. The usage of two non-destructive instruments (Dualex and Multiplex) allowed us to gain insights in ontogenetical effects at the leaf level and temporal development of SM contents over time. Indices provided by those devices correlate fairly with amounts detected via HPLC (Cynaroside: R2 = 0.46 – 0.66; Graveobioside A: R2 = 0.51 – 0.71). The concentrations of both metabolites tend to decrease at leaf level during the ontogenetical development even under stress conditions. High-UV stress is a promising tool for enriching plant leaves with valuable SM without major effects on plant biomass. All data is available online [1].

Introduction: Pharmaceutical products are inevitable for human health. Owing to the growing need for pharmaceuticals, pharmaceutical companies introduce drugs annually into the market in addition to the extensive collection of existing pharmaceutical products. Households, farms, health facilities, and pharmaceutical industries release pharmaceutical waste into the environment at low concentrations through routine pharmaceutical use, damage, and expiry. The effects of active pharmaceutical ingredients (API) on non-target species in the environment are not known. Over the years, pharmaceuticals such as diclofenac and ibuprofen in trace amounts have been detected in public water systems, ground and surface water. Unwanted medicines should be safely disposed of at a reduced financial cost to mitigate the public and environmental health risks. Lack of general knowledge of how to dispose of unused pharmaceuticals leads to improper disposal resulting in accidental toxicity, rising healthcare costs, landfills pilfering/scavenging, water supply pollution, anti-microbial resistance, and death. To mitigate such effects, pharmacists should raise public awareness about safe disposal practices. Objective: This review aims to examine the sources of pharmaceutical waste, disposal costs, secure disposal methods, the effects of inappropriate disposal, and the role of pharmacists in the disposal. Method: The information on the stated objectives was gathered from available sources through a comprehensive literature review. Conclusion: Many countries contain tons of pharmaceutical waste that are expensive to destroy. Because of improper disposal, pharmaceutical waste has been found at trace amounts in drinking and surface water. A practical, environmentally sustainable approach to pharmaceutical waste management, with policies and guidelines, and public awareness campaigns, are necessary to address the problem of safe waste disposal. The national drug regulatory bodies should conduct environmental risk assessment resulting from the disposal of unwanted pharmaceuticals. Pharmacists should facilitate extensive training on sustainable drug use and proper pharmaceutical waste disposal at all levels to reduce the risks associated with improper disposal. Reduction of pharmaceutical waste generation at each step of a drug’s lifecycle, implementing takeback options, collection at approved sites, and modern technology to treat wastewater are highly recommended to reduce the effects of unwanted pharmaceuticals on human health and the environment.

Cigarette butts, also known as tobacco product waste (TPW), are the single most collected item in environmental trash cleanups worldwide. This study used an online survey tool (Qualtrics) to assess knowledge, attitudes, and perceptions about this issue among individuals representing the Framework Convention Alliance (FCA). The FCA has about 683 members on its listserv, including non-governmental tobacco control advocacy groups that support implementation of the World Health Organization’s (WHO) Framework Convention on Tobacco Control (FCTC). Respondents (n = 65) represented countries from all six WHO regions. The majority (82%) had heard the term TPW, and all considered TPW as an environmental harm at some level. Additionally, 29% of respondents failed to identify that “cigarette filters make smoking easier.” Most (73%) correctly identified TPW components; however, fewer (60%) correctly identified the composition of cigarette butts. The majority (57%) were unfamiliar with Extended Producer Responsibility (EPR) and Product Stewardship (PS) as possible environmental intervention strategies. Respondents expressing opinions concurred that adding a litter fee to fund TPW programs will aid in reducing tobacco use and reduce the environmental impacts of TPW (100%); that prevention, reduction, and mitigation of TPW could be an important part of international tobacco control programs (98%); and that banning smoking in outdoor venues could reduce TPW (95%). Only 16% reported effective prevention or clean-up efforts in their countries. Weighted rankings revealed that respondents’ saw the national government, the tobacco industry, and state governments as most important in addressing TPW. The results of this research will inform continuing international discussions by the FCTC Conference of the Parties (COP) regarding environmental policies that may be addressed within FCTC obligations.

This study revealed the synthesis of cross-linked chitosan/Citrus reticulata peel waste (C/CRPW) composites that could be used as low-cost and green bio-adsorbents for the removal of Congo red (CR) dye from aqueous solutions. C/CRPW composites containing different amounts of Citrus reticulata peel waste (CRPW) and chitosan were prepared and cross-linked with glutaraldehyde. The composites were characterized by FESEM, FTIR, and BET. The C/CRPW composites as a new type of bio-adsorbents displayed superior adsorption capability toward anionic CR molecules and the adsorption capacities increased by incorporation of CRPW. Effects of different ambient conditions such as contact time, pH, adsorbent dosage, initial adsorbate concentration, and temperature were fully studied. The conditions which obtained 43.57 mg/g of the highest adsorption capacity were conducted at pH 4, initial concentration of 100 mg/L, adsorbent dosage of 2.0 g/L, and contact time of 24 hours at 328 K. The adsorption data was found to follow the pseudo-second-order kinetic model and the Freundlich isotherm model. According to the findings of this investigation, it was observed that the C/CRWP composites can be used as adsorbents due to their advantages of simple preparation process, environmentally friendly, renewable, efficient, and low-cost.

In an increasingly resource-constrained era, the utilization approach of waste and by-products from grain processing, is attractive widely, considering both nutritive value and economic aspects and move towards more sustainable food systems. Following the fundamentals of a circular economy, the need of the hour lies in its effective utilization as a grain waste and by-products conversion into value-added products in food industry. The aim of this study is twofold: 1. Understanding the progress of grain waste and by-products to valorization in human nutrition, using bibliometrics; different literature databases namely Google Scholar, Web of Science and Elsevier Scopus have been evaluated for their merits and values; 2. Exploration of knowledge-based strategies, by reviewing the literature concerning the possible use of grain waste and by-products for food processing industry, reducing burden on virgin raw materials. The review allowed to unlock the latest-advances of upcycling side streams and waste from grain processing industry.

In this study on volume determination in waste sorting facilities, we evaluate the effectiveness of ultrasonic sensors and address waste-material-specific challenges. Although ultrasonic sensors offer a cost-effective automation solution, their accuracy is affected by irregular waste shapes, varied compositions, and environmental factors. Notable inconsistencies in volume measurements between storage bunkers and conveyor belts underscore the need for a comprehensive approach to standardize bale production. With prediction reliability being constrained by limited data sets, undocumented modifications to machine-settings and sensor failures, this task renders a challenging application area for Machine Learning. We explore related research and present dataset analyses from three distinct waste sorting facilities in Europe, addressing issues as sensor usability, data quality and material specifics. Our analysis suggests promising strategies and future directions for enhancing waste volume measurement accuracy, ultimately aiming to advance sustainable waste management.

The dolomite dust-emulsified asphalt composite with excellent mechanical properties was successfully prepared using alkali activation. The effects of different alkali concentrations and emulsified asphalt contents on the mechanical properties of the materials were studied. The mechanical properties and microstructure of the composites were analyzed using compressive strength tests, bending strength tests, and SEM characterization. The experimental results show that the specimens have excellent mechanical properties: the 7-day compressive strength can reach 76.67 MPa, and the bending strength is about twice that of silicate-based geopolymer-emulsified asphalt composite. With an increase in emulsified asphalt content, the compressive strength of the samples decreases, while the bending strength increases first and then decreases. When the emulsified asphalt content is 1%, the bending strength of the sample is up to 28.81 MPa, which is 25% higher than that of the sample without emulsified asphalt. This indicates that an appropriate emulsified asphalt content can play a toughening role in the system, providing a new idea for designing high-toughness alkali-activated materials.

The mining sector generates a substantial quantity of stone waste and tailings, which constitutes an environmental risk. The most prevalent method for disposing of this industrial waste is dumping, which contributes to soil deterioration and water contamination while acquiring precious land. It can be recycled using a number of processes, such as the promising geopolymerization technique, which transforms waste into value. This study reviews current developments in the manufacturing of mine tailings-based geopolymer composites from industrial waste as a possible sustainable building material. This paper also gives in-depth studies on the characteristics and behaviors of mine tailings composites used in geopolymer manufacturing, including durability, microstructure, thermal and leaching properties. This review also identifies knowledge gaps that must be filled in order to advance mine tailings composites for geopolymers.

By the end of 2023, biowaste must be completely separated or recycled at source based on the EU legislation. Separate biowaste collection and valorisation towards biofuels could play an essential role in the biobased circular economy. In this context, the principal goal of this paper was to demonstrate in pilot scale the technological solution of bioethanol production via the utilisation of urban source-separated biowaste within the city context of Athens, Greece. More specifically, the main aim was the demonstration of a pilot system in continuous operation (over 10 operating cycles) with real feedstock – wet separately collected biowaste. From the 11 pilot trials performed with wet feedstock, the mean starch and cellulose degradation of the pilot trials amounted up to 80.69±16.27% and 79.41±10.37% respectively, while the bioethanol yield was 74.05±6.82%. The latter was comparable to that of more intensive pretreatment methods. Homogenization and shredding that was applied in this study, stand as promising and cost-effective pretreatment methods for bioethanol production from wet feedstock. Further research is needed to optimize conditions and evaluate scalability. Nevertheless, pilot scale testing is a crucial step in the development and deployment of this technology since it serves as a bridge between laboratory research and full-scale implementation, offering a practical and controlled environment to validate and optimize the technology while minimizing risks and uncertainties.

The basic principles of geological risk calculation through Probability of Success (PoS) are mostly applied for numerical estimation of additional hydrocarbon existence in proven reservoirs or potential hydrocarbon discoveries in selected geological regional subsurface volume. It can be tailored and validated for a comprehensive input dataset collected in the selected petroleum province, adapted by dividing up geological events into several probability categories and classes. The most applied categories are (existence of) reservoir rocks, traps and isolators, source rocks, migration pathways and preservation conditions for hydrocarbons The methodology results in unique probability values as multiplication of independent statistical events, which can also be applied in the assessment of a potential hydrocarbon discovery of desired minimal volume and its value in any virtual currency like risk-neutral dollars. Such methodology has been extensively developed in the last decades in the Croatian subsurface, mostly in the Croatian part of the Pannonian Basin System (CPBS). Through the adaptation of geological categories, it was also applied in hybrid, i.e., stochastical, models developed in the CPBS (Drava Depression). Stochastically estimation of porosity was already applied. As the robustness of this methodology is very high, it was also modified to estimate the influence of water-flooding in increasing oil recovery in some proven Neogene sandstone reservoirs in the CPBS (Sava Depression). This new modification is being presented to be applied to geological risk calculation, intending to assess the safety of geological environment in deep wells, where depleted radioactive fuel would be disposed, a subject of great importance. The case study encompassed the magmatic and metamorphic rocks in the pre-Neogene basement of the CPBS. For disposal purpose, these are regionally lithologies considered as to be the safest ones considering petrophysical values, water saturation, recent weathering and tectonic activity.

Starting from an original survey conducted in eight countries in 2021 (Canada, China, Germany, Italy, Russia, Spain, UK, and USA), this research explores the relationship between household food waste and dietary habits in a cross-country comparative perspective. 8,000 questionnaires were recorded from samples representative of adult population of each country through an online survey conducted between the 13th and the 24th of August. The questionnaires were built on the work of Waste Watcher International Observatory on Food and Sustainability, an international observatory of social, behavioral and lifestyles dynamics behind household food waste. Relationship between per capita self-reported amount of food waste (expressed in kilocalories) and self-declared dietary habits (Traditional, Healthy and Sustainable, Vegetarian, Smart, Confused) was estimated using multiple linear regression models. Results show that Smart diets are associated with higher values of food waste in Canada, Spain, UK and USA. Vegetarian diets are associated to lower food waste values in China, Germany, UK and USA but not in Italy, Russia and Spain. Since the share of population adopting a Smart diet is on average 2.7% of the sample, interventions for food waste reduction should focus on this specific type of consumers, often associated to larger amounts of food waste.

Corneal opacity is a leading cause of vision impairment and suffering worldwide. Transplantation can effectively restore vision and reduce chronic discomfort. However, there is a considerable shortage of viable corneal graft tissues. Tissue engineering may address this issue by advancing xeno- keratoplasty as a viable alternative to conventional keratoplasty. In particular, livestock decellularization strategies offer the potential to generate bioartificial ocular prosthetics in sufficient supply to match existing and projected needs. To this end, we have examined the best practices and characterizations that have supported the current state-of-the-art driving preclinical and clinical applications. Identifying the challenges that delimit activities to supplement the donor corneal pool derived from acellular scaffolds allowed us to hypothesize a model for keratoprosthesis applications derived from livestock combining 3D printing and decellularization.

Since the early 1980s, a large number of research works on enzymes from the red king crab hepatopancreas have been conducted. These studies have been relevant both from a fundamental point of view for studying the enzymes of marine organisms and in terms of the rational management of nature to obtain new and valuable products from the processing of crab fishing waste. Most of these works were performed by Russian scientists due to the area and amount of waste of red king crab processing in Russia (or the Soviet Union). However, the close phylogenetic kinship and the similar ecological niches of commercial crab species and the production scale of the catch provide the bases for the successful transfer of experience in the processing of red king crab hepatopancreas to other commercial crab species mined worldwide. This review describes the value of recycled commercial crab species, discusses processing problems, and suggests possible solutions to these problems. The main emphasis is placed on the enzymes of the hepatopancreas as the most highly salubrious product of waste processed from red king crab fishing.

Mill scale is the by-product of iron and steel industry. It can be recycled via sinter plant or solid as sinter feed materials. 85 to 90% of the constituent particles are more than 0.008 inches. The iron content is near around 70 %, with a very small amount of alkaline compounds and non-ferrous metals. Mill scale is polluted and contaminated with lubricants, oils and greases from the equipment. In this experiment for recovering of oil from mill scale, it is treated with three different methods. Then all methods were compared according to the ability of oil elimination and iron recovered. After washing and boiling with surfactants, large amount of polluted waste water becomes a problem for environment so this wastewater was utilized for making of Microbial Fuel Cells (MFCs), production of electricity in MFC depends on the biodegradation of organic materials, so different waste were added in wastewater for making MFC. The remaining of MFC was converted in bioethanol, biodiesel and biofertilizer. So this research is economical and environmentally friendly and fulfilled the important aspect of green environment with zero waste. It will be a mile stone in the research of metallurgy, environmental engineering, recycling technology and zero waste management.

Little research has been done on occupational health ramifications of informal electronic waste (e-waste) recycling work, which is increasingly common in low- and middle-income countries, and very little is known about this in high-income countries. Our study evaluated informal and formal e-waste recycling workers in Chile, which was recently recognized as a high-income country. In 2017 we recruited 78 informal recycling workers from two cities, and 15 formal e-waste recycling workers from one recycling facility. Participants completed a questionnaire and health assessment regarding their involvement in, and potential impacts of, e-waste recycling, among other measures. Participants were primarily male, middle-aged, married with children, and had worked in e-waste recycling for an average of 12 years. Participants generally reported good health status, and chronic disease prevalence was similar to the national prevalence. Workers commonly reported exposures to several occupational stressors, including mental health stressors and noise, as well as insufficient income. Occupational injuries were common and use of safety equipment was low. No significant differences were found between informal and formal workers. Informal e-waste workers in Chile face occupational health challenges. The extent to which these issues impact the health of informal Chilean e-waste workers is unclear and warrants further research.

The article presents an experience based on the design of DIY materials (Do-It-Yourself) as a phenomenon that contributes to the circular economy, making use of household waste and organic binders. The development context is the southernmost Industrial Design School in Latin America, where students are educated through the transfer of knowledge emphasized on the experimentation and territory assessment. Methodology corresponds to the traditional industrial design process, inserting DIY design of materials in the strategic stage. Objective and subjective variables are determined applied in the definition of new materials, being able to determine a range of proposals based on household waste. Citrus × Sinensis, Peperomia caperata (Piperaceae), Radiata pine veneers, among them, which are conceived by students to be self-produced at the user level. The results are materials elaborated based on household waste, exemplified with three types based on organic husks. Beyond findings associated to technique, compatibilities between residual materials and results expressed in materials and catalogs, it is possible to educate future designers on the innovative theme, with the potential to improve life quality of people and their environments.

Slags and ashes generated in thermal waste treatment facilities require proper management. In line with the principles of the circular economy, new, more economical and ecological possibilities for utilizing these substances are sought. These waste materials exhibit characteristics similar to rocks in many aspects. This study focuses on analyzing the similarities and differences between nine selected rocks and three samples of slags and ashes obtained from municipal waste incineration. The main research device used was a polarizing microscope, using reflected, transmitted and fluorescent light. Additionally, low-pressure gas adsorption equipment, as well as helium and quasi-liquid pycnometers, were used for complementary analysis. The parameters analyzed mainly covered broadly defined petrographic properties of rocks and slags, with a particular emphasis on porosity, porous structure and the spatial distribution of pores and fractures. The conducted analyses confirmed a significant similarity between slags and ashes and clastic sedimentary rocks such as sandstones and mudstones. The research results underscore the importance of petrographic microscopic studies for analyzing materials other than rocks. They also allow for exploring applications for slags and ashes in areas traditionally reserved for natural rock resources. The findings also indicate the necessity of using methods other than microscopic ones to describe the pore space of rocks. The lower measurement range of the optical microscope is limited to approximately 1 μm, covering only macropores. Other methods extend this characteristic to micro- and mesopores. Therefore, a combination of different methods is often employed to obtain a more comprehensive characterization of rock porosity.

The emergence of the circular economy, and the evolving paradigms in the treatment and management of wastewater, have opened up an opportunity for co-digestion of organic waste (i.e., food waste) with sewage sludges to enhance resource recovery at wastewater treatment plants (WWTPs). This paper reviewed the potential for anaerobic co-digestion of food waste and sewage sludges, as well as alternative sustainable food waste handling systems in South Africa. The promotion of the circular economy by the latest national solid waste management strategy and the ongoing efforts for resource recovery by the wastewater sector suggests that anaerobic co-digestion of food waste and sewage sludge is possible in South Africa. Furthermore, an integrated food waste disposer (FWD) system was identified as a sustainable alternative for food waste handling. To formulate a roadmap for future food waste and sewage sludge co-digestion implementation, a multi-disciplinary investigation is required to bridge the literature gap.

In the ongoing work, environmentally sound technologies for converting organic wastes into fertilizers, to improve soil sustainability and crop yield have been identified and assessed. Wet wastes were combined with 50% wood sawdust and 50% 50% wet wastes (Compost 1) or (10% Straw + 90% wet wastes) (Compost 2) to produce soil improvers with a balanced level of nutrients and their effectiveness on soil ecosystem functioning have been tested and compared to horse manure (HM) and nitrogen:phosphorous:potassium (NPK) fertilizers. Unfertilized soil was used as control. Soil chemical and biological properties, have been detected after the harvesting of broccoli and red cabbage (90 days from the initial treatments). Three independent experiments have been conducted in open field in a randomized complete block design with three replications (n=9). Results showed that Compost 1 had the highest C/N ratio and CSC, indicating a better humification of wet material. Compost 1 even if contained a minor amount of organic carbon, as well as a less activity of FDA and DHA than Compost 2, was the most effective in improving soil quality, significantly increasing the labile fraction of organic matter, the oxidative enzyme (DHA), microbial biomass and crop yield. Both composts increased crop productivity.

Sustainable supply chain management (SSCM) represents a critical strategy for the electronics industry to balance economic objectives with environmental and social responsibility across complex global production networks. This multiple case study analysis investigates SSCM integration within leading Korean electronics manufacturers Samsung, LG, and Hyundai. In-depth qualitative data, focus groups, and sustainability report analysis reveals the policies, practices, results and implementation barriers related to incorporating sustainability criteria across procurement, manufacturing, distribution and recycling functions. Findings show sustainability considerations increasingly driven by cost, risk, reputational and regulatory factors, with vertical coordination initiatives helping transfer knowledge to assist suppliers on compliance and emissions reductions. Yet substantial obstacles persist around monitoring, coordination, transparency and technical capabilities, especially amongst lower tiers. The paper discusses how common reporting standards, ethical sourcing certification and partnerships can accelerate electronics supply chain sustainability. By mapping integration achievements and gaps, this study informs managerial best practices and policy reforms toward promoting socially and ecologically responsible models for Korea's vital export industry as it navigates rising stakeholder pressures.

The performance of recycled aggregate concrete deteriorates due to the defects of adhesive mortar, pores and cracks on the surface of recycled aggregate. It is of great engineering significance to modify the reclaimed aggregate to improve its performance and adaptability. In this paper, the physical and chemical properties of waste concrete recycled aggregate are reviewed. Then, the existing modification methods and technologies of recycled aggregate, including physical, chemical and biological methods, are reviewed. Finally, the existing problems of the current modification technology are summarized, and the future research direction is proposed. It is expected to provide a new idea and method for the modification of waste concrete recycled aggregate.

This scoping review examines global strategies and enterprises for sustainable solid waste management, with a focus on alternative landfilling approaches. The study collected and analyzed a significant number of documents from different regions, revealing Asia as the major contributor (for the collected documents) (48.7%), followed by North America (24.3%) and Europe (15.8%). Recycling emerged as the most effective alternative waste treatment method, representing 52.3% of the documented approaches, with industrial recycling (22.6%) and residential/non-residential recycling (20.2%) as prominent categories. Food waste was a significant concern across regions, constituting 21.4% of the collected documents. Composting was widely adopted (15.4%) due to its simplicity and benefits for gardening and soil improvement. Other methods like biogas extraction, reusing, raising awareness, incinerating, redistributing, reducing, and fermentation accounted for 13.1% cumulatively. The study highlights the need for tailored waste management solutions based on regional challenges and successful practices. Promoting recycling infrastructure, composting, and waste reduction approaches are crucial to achieving sustainable waste management aligned with SDGs. Collaboration and knowledge-sharing between regions are essential to improve inefficient waste management mechanisms. Integrating the findings into policymaking and industry practices can lead to a more sustainable future with reduced environmental impact.

The situation in the world of pandemics is rapidly changing, and the second wave of COVID-19 has put a lot of pressure on the government and private sector, which are primarily responsible for controlling the situation. COVID-19 positive cases have increased in recent months relative to last year, and the number of patients admitted to hospitals has also increased, despite the fact that few of them were denied admission due to shortage of beds. Normal people who experience any symptoms immediately isolate themselves and begin taking the COVID medications prescribed by medical personnel and their team. During these times, all domestic people tossed the wrappers and boxes of medicines into the regular trash can, and the waste was handed over to the waste collector, who treated it like any other domestic waste and disposed of it using open dumping or other methods. The goal of this perspective is to suggest the collections of these types of waste from domestics, and protect the natural resources like water, soil, and even living beings like animals from pollution (from the effect of SARS-CoV-2). The main challenge for environmental waste management agencies is determining who has COVID positive and which houses generate these types of waste; thus, proposed strategy may be beneficial to the long-term sustainability of natural resources and animals.

The dry washing method is an alternative to replace water washing, thereby reducing the negative impacts of contamination. However, commercial adsorbents come from industrial processes that, due to their composition, may not be such a sustainable resource in the global biodiesel production process. In this study, the use of organic residues, such as sawdust, coconut fiber, nutshell, rice husk and water hyacinth fiber, were proposed as bioadsorbents for the purification of biodiesel from waste cooking oil (WCO). Quality parameters such as the acid value, water content, and free and total glycerin content were evaluated and compared with those of commercial resins such as Magnesol® and Amberlite™. Promising results were obtained using sawdust during the purification process, achieving a 31.6% reduction in the acid value compared to that of unpurified biodiesel, the reduction was 31.3% more efficient than Amberlite™. Sawdust adsorbed free glycerin at 55.8%, being more efficient than Amberlite™. The total glycerin values were similar between commercial resins and sawdust. A water content values were similar than Amberlite™ and better than that with Magnesol®, at 4.3% and 39.81%, respectively. These results show that sawdust can be used as an alternative bioadsorbent in a dry purification method for biodiesel being a residue with less environmental impact.

This study evaluates the production of biohydrogen from agro industrial waste. The worldwide energy demand is increasing exponentially and the reserves of fossil fuels are depleting, the combustion of fossil fuels has the effect on environment because of CO2 emission. Hydrogen generation market size is forecast to cross 180 billion by 2024, according to a new research report by global market. For the production of biohydrogen. we had chosen groundnut shell as our source, using Tween80 as a surfactant we had undergone pre-treatment studies for (10min,20min,30min,40min,50min) we had estimated the content of cellulose, protein, carbohydrates at (1%,2%,3%,4%,5%) and obtained the optimum value in the form of graph. The production of hydrogen is done by using the rumen fluid of the cow and the quantity of the hydrogen produced by this process is identified by using the analytical instrument Gas Chromatography.