Electrodeposition of cadmium telluride (CdTe) on fluorine doped tin oxide (FTO) using two electrode configuration was successfully achieved with the main focus on the growth temperature. The electroplating temperatures explored ranges between (55 and 85)℃ for aqueous electrolytes containing 1.5 M cadmium nitrate tetrahydrate (Cd(NO3)2 •4H2O) and 0.002 M tellurium oxide (TeO2). The ensuing CdTe thin-films were characterised using X-ray diffraction (XRD), UV-Vis spectrophotometry, scanning electron microscopy (SEM), energy dispersive X-ray (EDX) and photoelectrochemical (PEC) cell measurements. The electroplated CdTe thin-films exhibit a dominant (111) CdTe cubic structure, while the crystallite size increases with the increase in the electroplating temperature. The internal strain, dislocation density and the number of crystallites per unit area decrease with increasing growth temperature. The optical characterization depicts that the CdTe samples show comparable absorbance and a resulting bandgap of 1.51±0.03 eV for as-deposited CdTe layers. A marginal increase in the bandgap and reduction in the absorption edge slope towards lower deposition temperatures were also revealed. The annealed CdTe thin-films showed improvement in energy bandgap as it tends towards 1.45 eV while retaining the aforementioned absorption edge slope trend. Scanning electron microscopy shows that the underlying FTO layers are well covered with increasing grain size observable relative to the increase in the deposition temperature. The energy dispersive X-ray analyses show an alteration in the Te/Cd relative to the deposition temperature. Higher Te ratio with respect to Cd was revealed at deposition temperature lower than 85℃. The photoelectrochemical cell study shows that both p- and n-type CdTe can be electroplated and that deposition temperatures below 85℃ at 1400 mV results in p-type CdTe layers.

In this work, we report the fabrication of the new heterojunction of two 2D hybrid layered semiconductors, ZnO(stearic acid)/V₂O₅(hexadecylamine), and its behavior in the degradation of aqueous methylene blue under visible light irradiation. The optimal photocatalyst efficiency, reached at a ZnO(stearic acid)/ V₂O₅(hexadecylamine) ratio of 1:0.25, results to be about six times higher than that of pristine zinc oxide. Reusability test shows that after three photocatalysis cycles no significant changes in neither the dye degradation efficiency loss nor photocatalyst structure occur. Visible light photocatalytic performance observed indicates there is synergetic effect between both 2D nanocomposites used in the heterojunction. The visible light absorption enhancement promoted by the narrower bandgap V₂O₅ based components; an increased photo generated charge separation favored by extensive interface area; and abundance of hydrophobic sites for dye adsorption appear as probable causes of the improved photocatalytic efficiency in this hybrid semiconductors heterojunction. Estimated band-edge positions for both conduction and valence band of semiconductors together with experiments using specific radical scavengers allow a plausible photodegradation mechanism.

In this work, we develop a self-consistent physical model of bubbles in a gas solid two-phase flow. Using the Peng-Robonson state equation and a detailed specific heat ratio equation of bubbles, we obtain the kinetic equations of the bubbles on the basis of the Ergun equation, thermodynamic equations, and kinetic equations. It is found that the specific heat ratio of bubbles in such systems strongly depends on bubble pressures and temperatures, which play an important role in the characteristics of the bubbles. The theoretical studies show that with increasing height in the systems, the gas flow rate shows a downward trend. Moreover, the larger particles in the gas solid flows are, the greater the gas velocity is. The bubble sizes increase with the increasing heights of the gas solid systems, and then decrease. The bubble velocity is affected by the gas velocity and the bubble size, which gradually increase and eventually quasi-stabilize. This shows that gas and solid phases in a gas solid two-phase flow interact with each other and a self-consistent system comes into being. The theoretical results have exhibited important value as a guide for understanding the properties and effects of bubbles in gas solid two-phase flows.

For a wide field of view (FoV) wavefront coding athermalized infrared imaging system with a single decoding kernel, the off-axis aberration tends to cause artefacts. In order to correct off-axis aberration, many pieces of lenses will reduce the transmission efficiency and increase the weight and cost. To meet requirements for wide FoV, wide operating temperature and low weight of infrared imaging systems, this paper reports a wide-FoV wavefront coding athermalized infrared imaging system with a two-piece lens. Its principle, design, manufacture, measurement and performance validation are successively discussed. This paper constructs an optimization problem which maximizes the weighted mean of PSF consistency for both the FoV and operating temperature range. The two-piece lens contains four surfaces, where three aspheric surfaces are introduced to reduce optical off-axis aberrations and a cubic surface is introduced to achieve athermalization. The optical phase mask containing an aspheric surface and a cubic surface is manufactured by nano-metric machining of ion implanted material(NiIM). Experimental results validate that our wide-FoV wavefront coding athermalized infrared imaging system has a full FoV of 26.10° and an operating temperature over -20°C to +70°C.

Due to its time effective, joint friendly and highly customizable character whole-body-electromyostimulation (WB-EMS) is regarded as a feasible solution for a large variety of training issues particularly in the area of non-athletic application. To identify gaps in research and summarize prevalent evidence we conducted an evidence map on outcomes addressed by WB-EMS trials in middle-aged to older, non-athletic adults. Based on a comprehensive systematic search in five databases and two study registers according to PRISMA, 54 projects published in 80 articles were included. More than 90% of the studies reported outcomes related to the physical fitness or function domain. Body composition parameters were addressed by two thirds of the projects. Health-related outcomes addressed by WB-EMS included cancer/neoplasm (n=7), endocrine regulation (n=8), glucose metabolism (15), nervous system diseases (n=2), cardiovascular system diseases (n=22), non-specific chronic low back pain (n=4), osteopenia (n=5) and diseases of the renal system (n=12). Outcomes related to inflammation were addressed 18 times. Of importance, no studies reported clinically relevant adverse effects related to the WB-EMS intervention. In summary, while considerable evidence on outcomes related to fitness/function and body composition is prevalent, evidence gaps of WB-EMS research were particular evident for diseases of the nervous and cerebrovascular system.

Objective: Local ablation therapies (radiofrequency ablation (RFA), and microwave ablation (MWA)) are important as curative treatment option in patient with early-stage hepatocellular carcinoma (HCC) and option for intrahepatic tumor volume reduction in those with unresectable HCC. Various techniques; contrast-enhanced ultrasound (CEUS), real-time virtual sonography (RVS), artificial pleural and ascites fluid infusion, and body position change (BPC) have been used to accurately and safely perform local ablation therapies. However, there have been few reports on the usefulness of BPC. Therefore, this study focused on the usefulness of BPC during local ablation therapies in patients with HCC. Methods: We evaluated the technical success rates, treatment time, and prognosis of 283 nodules treated with local ablation therapies. Furthermore, we defined nodules adjacent to large vessels or extrahepatic organs, or poorly visible nodules using US as HCC in high-risk locations. High-risk locations HCC were classified into phase 1 (before active use of BPC, January 2018 to December 2019) and phase 2 (after active use of BPC, January 2020 to January 2022). Results: One hundred seventy-six nodules (62%) were classified as high-risk location group. Compared to non-high risk HCC, treatment-assist techniques, such as BPC (61 vs. 24 %, p<0.001), artificial pleural fluid infusion (24 vs. 5.6%, p<0.001), artificial ascites infusion (50 vs. 11%, p<0.001), fusion imaging (28 vs. 8.4%, p<0.001) and CEUS (26 vs. 4.7%, p<0.001) were performed more frequently for high-risk HCC. The technical success rates were 96% (271/283 nodules), 96% (167/173 nodules) and 95% (102/107 nodules), for all nodules, the high-risk location group and the non-high risk location group, respectively. In the high-risk location group, the technical success rates of the group without BPC were lower than that with BPC (91 vs. 99%, p=0.015). Only BPC was a related factor for the technical success rate for high-risk locations HCC (OR 10 (1.2-86), p=0.034). In contrast, no differences were found in the treatment time, the local tumor progression rates, intrahepatic distant recurrence rates, and overall survival between the group with BPC and that without BPC in the high-risk location HCC. Conclusion: BPC during local ablation therapies in patients with HCC in high-risk locations was safe and efficient. Body position should be adjusted for HCC in high-risk locations to maintain good US visibility and ensure safe puncture route in patients undergoing local ablation therapies.

Introduction: Overuse of antibiotics has been increasing in recent years and is currently the most prescribed drug in the paediatric age. It is estimated that 72% of patients in the neonatal intensive care unit (NICU) are treated with antibiotics. One of the effects observed with their use is the alteration of the microbiota, which is associated with metabolic disorders including obesity. In this study, the aim was to determine in newborn rats, whether most commonly prescribed antibiotics in Mexican NICUs have a differential effect on weight gain, development of adiposity, and modification of carbohydrate and lipid metabolism. Methods: This is an experimental study in newborn rats, comparing Ampicillin/Meropenem (Access/Watch groups) 100 mg/g every 12 h /10 mg/g every 12 h (each of these two antibiotics was adjusted to the required dosages based on weight); Cefotaxime 200 mg/g every 24 h; (Watch group) and Amikacin 15 mg/g every 24 h (Access group) versus Saline Solution as Control. Each antibiotic was intraperitoneal administered daily for 5 days in males (to avoid gender differences) to 14 newborn rats in each group. A comparison of anthropometric and biochemical parameters registered on day 28 was made using ANOVA analysis. Differences were considered if p < 0.05.Results: Amikacin was the antibiotic with the greatest effect on anthropometric measurements and LDL-cholesterol; as well as Cefotaxime on Glucose and triglycerides, while Meropenem plus Ampicillin showed the weakest effect on measured parameters. Conclusion: The administration of antibiotics in the neonatal stage has repercussions on the body composition of adult rats, as well as on lipids and carbohydrates serum levels. Future studies might evaluate the toxicity of antibiotics on the immature neonatal organs.

Background: Physiological changes of blood amino acids and acylcarnitines during healthy child development are not well studied. The LIFE Child study offers a platform with a large cohort of healthy children to investigate these dynamics. We aimed to assess the intra-person variability of these blood metabolites and associations with anthropometric parameters related to excess body fat and IGF1 serum levels. Methods: Concentrations of 23 amino acids, 5 acylcarnitines and free carnitine of 2213 children aged between 3 months and 19 years were analyzed using liquid chromatography/tandem mass spectrometry. Standard deviation score values were used to account for physiological sex- and age-related differences. The stability of metabolites was assessed through the coefficient of determination. Associations with parameters for body composition and IGF1 serum levels were determined by Pearson correlation and linear regression. Results: Our research reveals substantial fluctuations in metabolite concentrations in the same person during childhood and adolescence. Most metabolites had a positive correlation with parameters of body composition with notable influence of sex, pubertal status and weight group specific differences. Glycine exhibited negative associations with parameters of body fat distribution especially in normal weight girls, overweight/obese boys and during puberty. Conclusions: The observed alterations in metabolite concentrations contribute to our knowledge on the complex interplay between blood amino acid and acylcarnitine levels and metabolic health in children and adolescents.

Ionizing radiation exposure is known to induce molecular and cellular injury, inflicting a cascade of potentially catastrophic events leading to tissue and organ damage. Metabolomic analysis allows for the identification and quantification of small molecules downstream of genomic changes induced by radiation exposure. We aimed to characterize metabolomic changes that underscore the prefinal stage of lethally irradiated rhesus nonhuman primates (NHPs). Peripheral blood was drawn at baseline, post-exposure as well as at the preterminal stage of NHPs (immediately prior to death in moribund NHPs), which did not survive exposure with 7.2 Gy total-body radiation (LD70/60). Herein, we analyzed global metabolomic changes using ultra-performance liquid chromatography (UPLC) quadrupole time-of-flight mass spectrometry (QTOF-MS) in plasma samples of NHPs collected at various timepoints in relation to irradiation. The overall goal was to identify metabolic shifts present immediately prior to death. Our findings, for the first time, show that radiation induced significant time dependent metabolic perturbations when compared to pre-irradiation samples, particularly in the glycerophospholipid metabolism and steroid hormone biosynthesis and metabolism pathways. These findings provide valuable insights for identifying biomarkers for lethality, which may be helpful for triage during a mass casualty scenario.

Background: Assessing body image and personalized rehabilitation in lower limb amputation is essential to measure impact on an individual’s quality of life and psychosocial wellbeing. The aim of this study was to develop a Spanish version of the Amputee Body Image Scale (ABIS-E) for Spanish-speaking lower limb amputee. Methods: A cross-sectional study was conducted including amputee patients in local in Madrid, Spain. Clinical outcomes about body image (Amputee Body Image Scale, ABIS), health-related quality of life (EuroQol-5D-5L), depression and anxiety (Hospital Anxiety and Depression Scale, HADS), pain (Brief Pain Inventory-Short Form, BPI-SF) and functional capacity (Prosthesis Evaluation Questionnaire, PEQ) were collected. Results: Seventy-three participants were assessed. Excellent test-retest reliability (ICC=0.847) and good internal consistency (Cronbach's alpha=0.753) were obtained. Three factors were extracted in the factor analyses. Convergent validity with Pearson's and Spearman's correlation coefficients were calculated for the depression and anxiety questionnaires (HADS) (values between .57 and .67), functional capacity (PEQ) (values between -.35 and .71) and quality of life (EQ-5D-5L) (values between -.37 and .61). Conclusions: The ABIS-E is a reliable and valid tool for measuring body image in the Spanish population with a lower limb amputation, potentially useful in primary care to identify psychosocial problems.

The A. japonicus industry has expanded significantly, but no research has focused on how to de-termine the age of A. japonicus during farming. Correctly estimating the age of A. japonicus can provide a decision-making basis for the breeding process, and data for the protection of A. japonicus aquatic germplasm resources. DNA methylation levels in the body wall of Apostichopus japonicus at 4 months, 1 year, 2 years, and 3 years old were determined by MethylRAD-Seq, and differentially methylated genes related to age were screened. The results of the study found that 441 and 966 differentially methylated genes were detected at CCGG and CCWGG sites, respectively. As-partate aminotransferase, succinate semialdehyde dehydrogenase, isocitrate dehydrogenase, the histone H2AX, heat shock protein Hsp90, aminopeptidase N, cell division cycle CDC6, Ras GTPase activating protein (RasGAP), slit guidance ligand slit 1, integrin linked kinase ILK, mechanistic target of rapamycin kinase Mtor, protein kinase A Pka, and autophagy-related 3 atg3 these genes may play key roles in the growth and aging process of A. japonicus. This study provided data for identifying the age of A. japonicus.

Eating disorders, especially restrictive eating, are common among female athletes. There are two main types of winter sports, those that are practised outdoors on snow (-25 to +5ºC and 2500 m), such as alpine skiing or snowboarding, and those that are practiced indoors on ice (5-10º C at low altitude), such as figure skating and ice hockey. The aim of this research was to identify the nutritional status and potential risk of female athletes practising winter sports considering the altitude of training. The sample was composed of 58 women (aged 19.81 years (SD: 12.61) who were competitors in some winter sports. Anthropometrics and nutritional variables were taken. Statistically significant differences were found between groups for all the characteristics except thigh skinfold and neither group had an EI that matched their TEE. Both groups met at least 2/3rd of the RDI for all minerals and vitamins, except iodine, fluorine, vit D, E and retinol. This study suggest that female winter sports athletes have insufficient energy, vitamin and mineral intake that can be worsened by altitude.

Stem cells can be used in cellular therapy. This happended in order to replace damaged cells or having aim to regenerate organs. The definition of stem cells can be extended. From this point of view, we can mention taking in consideration the idea in which it is known that these cells form the base of the building body. More than, we can mention that stem cells are characterized by two knowing properties namely differentiation and selfrenewal. Based on the observation that differentiation of adult stem cells into specific derivativescan be controlled by laboratory techniques, it is anticipated that adult stem cells may become the basis of therapies for many, and various types of medical conditions. Taking on stem cells, regenerative medicine (RM) it is known as being one of the hottest topics in biotechnology nowadays. From this purpose, stem cells can be used in regenerative medicine (RM). The principles of regeneration are found in different types of cultures, from long time ago, centuries etc.

A method of measuring the absolute pose parameters of a moving rigid body using a monocular camera is proposed, aiming at addressing calibration difficulties and inconsistencies of repeated measurements of the rigid-body pose for a camera having a varying focal length. The proposed method does not require calibration beforehand. Using more than six non-coplanar control points symmetrically arranged in the rigid-body and world coordinate systems, the matrices of rotation and translation between the camera and two coordinate systems are obtained and the absolute pose of the rigid body measured. In this paper, formulas of the absolute pose measurement of a moving rigid body are deduced systematically and the complete implementation is presented. Position and attitude measurement experiments carried out on a three-axis precision turntable show that the average absolute error in the attitude angle of a moving rigid body measured by an uncalibrated camera at different positions changes by no more than 0.2 degrees. Analysis of the three-dimensional coordinate errors of the centroid of a moving rigid body shows little deviation in measurements made at three camera positions, with the maximum deviation of the average absolute error being 0.53 cm and the maximum deviation of the standard deviation being 0.66 cm. The proposed method can measure the absolute pose of a rigid body and is insensitive to the position of the camera in the measurement process. This work thus provides guidance for the repeated measurement of the absolute pose of a moving rigid body using a monocular camera.

Adiposity is associated with adverse health conditions such as obesity, cardiovascular disease and type 2 diabetes. The combination of resistance exercise and creatine supplementation has been shown to decrease body fat % in adults ≥ 50 years of age. However, the effects in adults < 50 years of age is unknown. To address this limitation, we systematically reviewed the literature and performed several meta-analyses comparing studies that included resistance exercise and creatine supplementation to resistance exercise and placebo. Twelve studies were included involving 266 participants. Adults (< 50 years of age) that supplemented with creatine and performed resistance exercise experienced a significant reduction in body fat % (-1.19%, p=0.006) and a non-significant reduction in absolute fat mass (-0.09 kg, p=0.88). Collectively, the combination of resistance exercise and creatine supplementation produces a very small reduction in body fat % in adults < 50 years of age.

BACKGROUND: It has been known for decades that breastfeeding leads to a lower risk of asthma, respiratory infections, or metabolic syndrome at school age. In addition, evidence is now accumulating on the influence of breast milk on the shape, volume, or function of the heart and lungs. Within this field of research into the effects of breast milk on the structure of the heart and lungs, we have set out to analyze the differential electrocardiographic characteristics of schoolchildren who were once breastfed. METHOD: Observational cross-sectional study including 138 children aged 6 or 12 consecutively presenting to a well-child clinic between May and December 2022. Inclusion criteria: the ability to perform reproducible ECG records, the feasibility of weighing and measuring patient, and breastfeeding data collected from birth. RESULTS: Using the 40º cut-off value for the mean P-wave axis among schoolchildren, 76% of never breastfed children in our sample have a P-wave axis in a more vertical position than the mean as compared to 58% of ever-breastfed children (OR:2.25;95%CI:3.13-1.36); there was no other significant difference between infant feeding groups in somatometric characteristics or ECG parameters, CONCLUSION: We found a significant difference of the mean values of the P-wave axis between never and ever breastfed children. Although this report should be approached cautiously, these findings add to the renewed interest in discerning developmental interventions to improve cardiovascular health.

Aqueous enzymatic method is a green oil extraction technology with limited industrial application owing to the need for demulsification of the oil body intermediate product. Existing demulsification methods have problems including low demulsification rates and high costs, such that new methods are needed. Free fatty acids produced by lipid hydrolysis can affect the stability of peanut oil body (POB) at a certain concentration. After screening even-carbon fatty acids with carbon chain lengths below ten, caproic acid was selected for demulsification of POB using response surface methodology and a Box–Behnken design. Under the optimal conditions (caproic acid concentration, 0.22%; material-to-liquid ratio, 1:4.7 (w/v); time, 61 min; and temperature, 79 C), a demulsification rate of 97.87% was achieved. Caproic acid not only adjusted the reaction system pH to cause aggregation of the POB interfacial proteins, but also decreased the interfacial tension and viscoelasticity of the interfacial film with increasing caproic acid concentration to realize POB demulsification. Compared with pressed oil and soxhlet-extracted oil, the acid value and peroxide value of caproic acid demulsified oil were increased, while the unsaturated fatty acid content and oxidation induction time were decreased. However, the tocopherol and tocotrienol contents were higher than those of the soxhlet-extracted oil. This study provides a new method for the demulsification of POB.

Knowledge of body composition is essential for athletes for their sport performance. It has yet to be determined whether differences in body composition are present between international and non-international players playing in the same elite professional club competition. Similarly, it is not yet clear whether differences in body composition according to ethnic origin exist in the elite professional game, where relative homogeneity is to be expected among soccer players. There is no single anthropometric profile that guarantees sporting success, as the somatotype of football players differs according to their individual characteristics. The aim of this study was to assess the description and comparison of the body composition profile of latin american professional football players playing in european leagues. The sample was composed of 238 subjects football players from European professional football leagues. Differences were found in all variables measured. The present study shows that in Latin American professional football players playing in Europe, there are significant differences in different body composition variables such as weight, height, WC, skinfold and fat values. This means that the treatment of these data and the possible classifications of sporting performance carried out in football clubs should be different to other European or African-American football players.

Background: Students in the United States gain weight significantly during their first year of university, however limited data are available for Australian students. Methods: This 12-month observational study was conducted to monitor monthly body weight and composition, as well as quarterly eating behaviours, dietary intake, physical activity, sedentary behaviours, and basal metabolic rate changes amongst first-year Australian university students. Participants were first-year university students over 18 years. Results: Twenty-two first-year university students (5 males and 17 females) completed the study. Female students gained weight significantly at two, three, and four-months (+0.9 kg; +1.5 kg; +1.1 kg, p <0.05). Female waist circumference (2.5 cm increase at three-months, p = 0.012), and body fat also increased (+0.9%, p = 0.026 at three-months). Intakes of sugar, saturated fat (both >10% of total energy), and sodium exceeded recommended levels (>2000 mg) at 12-months. Greater sedentary behaviours were observed amongst male students throughout the study (p <0.05). Conclusions: Female students are at risk of unfavourable changes in body composition during the first year of university, while males are at risk of increased sedentary behaviours. High intakes of saturated fat, sugars, and sodium warrant future interventions in such a vulnerable group.

Background: Body dysmorphic disorder (BDD) is a psychiatric disorder characterized by excessive preoccupation with imagined defects in appearance. Optical illusions induce illusory effects that distort the presented stimulus thus leading to ambiguous percepts. Using electroencephalography (EEG), we investigated whether BDD is related to differentiated perception during illusory percepts. Methods: 18 BDD patients and 18 controls were presented with 39 optical illusions together with a statement testing whether or not they perceived the illusion. After a delay period, they were prompted to answer whether the statement is right/wrong and their degree of confidence for their answer. We investigated differences of BDD on task performance and self-reported confidence and analysed the brain oscillations during decision-making using nonparametric cluster statistics. Results: Behaviorally, the BDD group exhibited reduced confidence when responding incorrectly, potentially attributed to higher levels of doubt. Electrophysiologically, the BDD group showed significantly reduced alpha power at mid-central scalp areas, suggesting impaired allocation of attention. Interestingly, the lower the alpha power of the identified cluster, the higher the BDD severity, as assessed by BDD psychometrics. Conclusions: Results evidenced that alpha power during illusory processing might serve as a quantitative EEG biomarker of BDD, potentially associated with reduced inhibition of task-irrelevant areas.

Overweight/obesity is one of the most important health problem worldwide. Birth by cesarean section has been shown to influence long-term health outcome including obesity. The aim of this systematic review-meta-analysis is to examine whether cesarean section increases the risk of offspring’ s overweight/obesity. The study follows the PRISMA and MOOSE guidelines. A systematic literature search was con-ducted on Scopus, PubMed, and WoS until December 2020. For inclusion, studies must have re-ported either (I) both Birth by cesarean section and adult (≥ 18 years) offspring BMI, (II) cohort or case–control study design and (III) a risk estimate. Heterogeneity testing was performed using Cochran's Q and I2 statistics. Publication bias was assessed by Egger’s test and Begg’s test. Me-ta-analysis was performed through a random effect model. Eleven studies with a combined population of 180.408 subjects were included in the meta-analysis. The overall analysis (n = 18) yielded a combined risk estimate for overweight/obesity of 1.19 (95% CI 1.08-1.31) and the test of heterogeneity resulted Q=53,37 (I2 = 70,37 %, P≤0•0001). The risk of offspring obesity is 1.23 (95% CI 1.09-1.39) and the test of heterogeneity resulted Q=39.50 (I2= 72,15%, P≤0•0001). Children born by cesarean section have an increased risk of developing obesity in adulthood

Objective On the eve of the summer Olympic Games in Tokyo research focus has shifted on the core temperature responses of elite athletes competing in the heat. In the absence of the field data of core temperature during Olympic sailing competition aim of the present study was to identify core temperature response during the Tokyo 2020 Olympic Test Event. Methods Four elite athletes from Olympic sailing (177.5±5.2 cm, 71.1±7.4 kg, body mass index 22.5±1.4 kg/m2, 24.8±3.7 yrs, VO2max 50.6±7.2 mL/min/kg)): 2 males and 2 females participated in the study. Core temperature was recorded using e-Celsius ingestible capsules, heart rate using a heart rate monitor. Ambient conditions in direct sunlight were measured using portable meteo station. Results Core temperature was recorded at water environment via an ingestible capsule in 4 sailors during the training (T), and competition (C), respectively. Ambient conditions in direct sunlight were hot and humid: during training temperature were 30.9°C±1.7°C and relative humidity 81.4%±2.8%, corresponding to a wet-bulb globe temperature of 41°C±4°C and during competition temperature was 31.2°C±2.3°C and relative humidity 87.2%±4.4%, corresponding to a wet-bulb globe temperature of 45.2°C±8.9°C. Core temperature increased during training reaching higher peak values (38.6°C±0.4°C) and during competition (38.9°C±0.4°C). The highest temperature recorded was 39.4°C (C). Conclusion The current study provides unique information into the core temperature parameters under heat stress in elite Olympic sailors during training and race event.

Body-Esteem Scale is an assessment tool for adolescents and adults that evaluate three dimensions of self-evaluations of one’s body. Body-Esteem Scale has been translated and validated in some countries since America down to Europe. Lack of translation and reliability evidence in Portugal was detected. This study aimed to translate and test the validity and reliability of the Body Esteem Scale for Adolescents and Adults (BESAA) in students in the context of Portuguese higher educa-tion. A total of 173 students (60.7% are female) with a mean age of 19.7 (standard deviation = 2.2) years participated. Categorical Principal Component Analysis was used to assess the underlying dimensions of BESAA. Construct validity was evaluated through correlation with the Appearance Schemas Inventory – Revised and a three-factor model (“Appearance”, ‘‘Weight’’ and “Attribu-tion’’) was established. Confirmatory factor analysis was performed to verify the construct validity of the instrument. Items that had factor weights (λ)<.40 were removed, as well as those that were considered redundant by the modification indices estimated by the Lagrange Multipliers (LM) method (LM>11, p<.001). We observed high correlations between theoretically similar factors, and low correlations between different factors. The Portuguese BESAA showed adequate validity and reliability.

The aim of this article was to examine if there are position-specific differences in the morphological characteristics of sub-elite female football players and to establish normative standards for this level of female football players. The morphological features of 101 sub-elite female football players (age: 21.8±2.7 years) were assessed. Twenty anthropometric sites were used in the measurements of body composition and somatotype. The average value of body fat percentage was 20.8±5.7%. The somatotype of the overall group was 4.0–2.4–2.1. Positional significant (p ≤ 0.05) differences were found between goalkeepers and outfield players in morphological characteristics. Goalkeepers were taller, heavier, possessed the highest body fat percentage and showed higher values for all skinfolds, breadth, girth and length measurements. However, there were very few practically worthwhile differences between the outfield positions. Positional groups did not differ (p ≤ 0.05) in somatotype characteristics either. The study suggests that at sub-elite level there are mainly differences between goalkeepers and outfield players, but outfield players are homogeneous when comparing morphological characteristics. These results may serve as normative values for future comparisons regarding the morphological characteristics of female football players.

Background: Overweight and obesity are becoming serious public health menace in the world today. Weight gain is skyrocketing across the globe due to growing economy, fast food expansion and a shift towards more sedentary living. However, most people lack knowledge regarding risks associated with overweight and obesity. Aim: The study aimed to explore the knowledge level of bankers in the Ho Municipality on the health risks associated with overweight and obesity. Methodology: A cross-sectional study design with quantitative method was employed. The study spanned from September 7, 2018 to April 25, 2019. A self-administered questionnaire and convenience sampling technique were used to obtain data. Data were analysed using IBM SPSS Statistics 21 Developer and the results presented in statistical tables and graphs. Results: Of 136 participants investigated, 67 (49.3%) were between 31 - 40 years. 2 participants (1.5%) were underweight, 49(36.0%) had normal weight, 43(31.6%) were overweight while 42 (30.9%) were obese. The study revealed that female bankers were prone to overweight (37.78%) while the males were prone to obesity (56.52%). Participants generally had low knowledge and awareness on health risks of overweight and obesity. Conclusion: Most bankers in the Ho Municipality were overweight and obese due to insufficient knowledge and low awareness on the risks associated with overweight and obesity. Public education and awareness creation are urgently needed to stem the tide.

Mexico shows a high prevalence of obesity in children and adolescents. Geographical location and cultural environment could play a role in the promotion of healthy lifestyles in terms of physical activity (PA), sedentary behavior (SB) and nutrition. The purpose of this study was to assess rural and urban differences in body composition (BC), physical fitness (PF), PA and nutritional status of adolescents from the state of Jalisco (Mexico). The study involved 469 students aged 13-17 years (55.0% girls) from 8 high schools. BC was analyzed by bioimpedance, and PF by standardized field tests. Objective measurements of PA and SB were taken in a subsample (n=240). Energy intake (EI) was calculated from two 24h recalls. Rural residents presented a higher prevalence of overweight, waist circumference, trunk fat mass, regional fat free mass and muscle handgrip strength (all p&lt;0.05, ηp2&lt;0.06). Cardiorespiratory fitness was similar among participants, whereas urban adolescents showed higher muscle power, speed-agility and flexibility scores (all p&lt;0.05, ηp2&lt;0.07). Overall lifestyle behavior in urban adolescents was more sedentary (p&lt;0.05, ηp2= 0.11). EI was similar in both locations. In conclusion, urban Mexican adolescents presented a generally higher sedentary behavior and better fitness and fatness profile than their rural peers.

Studies on the gait's parameters have been identified on the patients population. Most researchers confirm that the patients walk differently than normal people and they may have a risk for falls. Consistent finding and description of gender, age, and body mass index differences in gait studies is rare in healthy subjects. A cross-sectional study with forty-five young adult (F = 20, M = 25) was conducted. Stadiometer and Physilog 4 inertial sensors were used for data collection. A gait analyser 5.2 software (GaitUp, S.A. Lausanne, Switzerland) was used to determine spatiotemporal parameters. No statistically significant differences were found in any bilateral foot gait parameters with respect to gender, age, and body mass index. Females are found with higher total double support and cadence than males. Cadence also increases with age. Obese people showed lower gait speed, cadence, and total double support. These findings may be beneficial to those who have abnormal gait pattern due to age, body mass index differences, decreased muscle strength, spasticity, and joint mobility. This important informations should be considered to rehabilitate patients with abnormal gait patterns to controlling dynamic balance and riks to falling.

The classic Body Mass Index, (BMI), developed in the 19^th century by the Belgian mathematician Adolphe Quetelet [1] is an important indicator of the risk of death, of obesity, of negative health consequences, body fat percentage and of the shape of the body. While he BMI is assumed to indicate obesity in sedentary people and in people who do not practice sports, it is undisputed and a consensus among researchers [2][3][4][5][9][25] that Body Mass Index (BMI) is not a good indicator for obesity in people who developed their body through heavy physical work or sport but also in other segments of population such as those who appear to have a normal weight but in fact have a high body fat percentage and obese methabolism. The BMI also does not include all the variables essential for a health predictor. The BMI is not always a good predictor of metabolic disease, people who appear of healthy weight according to BMI have in some cases an obese metabolic syndrome. The BMI was developed as a law of natural sciences and “social physics” [1], as it was called then, before the middle of the 19^th century, and it had been used from the 70s for medical purposes, to detect obesity and the risk of mortality [6][7]. The BMI has a huge importance for modern society, affected by an obesity epidemic [8]. BMI has applications in medicine, sport medicine, sport, fitness, bodybuilding, insurance, nutrition, pharmacology. The main limitation of the BMI is that it does not account for body composition including non fat body mass such as muscles, joints, body frame and makes no difference between fat and non fat components of the body weight. The body composition and the proportion of fat and muscles make a difference in health outcomes [12][13][14][25][26][27][35][36][37] [38][39][40][41][42][43][44]…[100]. Body composition makes a difference also in the level of sport performance for athletes of every level. In nearly two centuries since the Body Mass Index was developed, no formula had been successfully developed to account for body composition and make the difference between muscle and fat in a consistent way. This can be considered a longstanding open problem of major importance for society. The objective of this analysis is to develop new formulae taking into account the health implication of body composition measured through indirect, simple indicators and making the difference between muscles and fat, healthy and non healthy metabolism. The formulae developed in this article are the only formula to successfully generalize BMI and make this difference. I develop a direct generalization of BMI, in the mathematical and physiological sense to account for fat and fat free mass and muscles, small and large body frames. It is the first such generalization because the classic BMI can be determined as a particular case of my formulae in the strict mathematical and practical physiologic sense. No other formula generalized the BMI to make the difference between fat and a large frame and muscles has ever been published in nearly two centuries since the BMI formula had been developed. The formulae I developed explain and generalize the conclusions of a large number of highly cited empirical experiments cited in the reference section. [35][36][37][38][38][39] [40][42][43][44]..[100] Most of the experimental proof I bring in support of my formulae and bodyweight quantification theory comes from many highly cited experimental research publications in medicine, sports medicine, sport science and physiology. My formulae explain also performance in decades of competitive sports and athletics

Social distancing, washing hands and good hygiene are essential and currently the most potent methods available to curb down the unprecedented speed by which the new coronavirus is spreading across the globe. Even under lockdown, which is necessary to significantly reduce the number of people that get infected by an ill person, are there additional measures that each of us can embrace to even further reduce the risk of infection and the severity of the COVID-19 disease? Given the lack of licensed drugs that target SARS-CoV-2 specifically, we have to look into additional non-specific defense mechanisms that animals and humans evolved to protect themselves from pathogen invasions. The goal of this article is to describe how various of our non-specific defense mechanisms work, which actually precede the inflammatory response, and to discuss whether we can exploit the unique features of the coronavirus envelope and the self-cleaning machinery of the human respiratory tract to strengthen our self-defense. The challenge is to actively interfere with supportive measures during the short time window between getting exposed and before an inflammatory response gets initiated.

This article attempts to propose a mathematical model and potential explanation regarding the unavoidable impact of a rigid body's peculiar shape on the seamless flow over it. The solid body completely immersed in a Newtonian fluid and respectively has a relative open circuit flow on it will typically experience various observable phenomena. These typical phenomena in laminar flow are explained using the proposed theory rather than conventional approximations or several partial theories. This article respectively represents an understanding of the laminar flow over a rigid body's external surface with due respect to its distinctive shape and size. To formulate a more realistic and simplified mathematical model for open circuit laminar flow over a body, a mathematical model is proposed based on the historical data of aerodynamics and theoretical mechanics. This mathematical model is intended to properly estimate forces on the continuous surface of the body in a laminar flow, to properly explain, understand and predict various phenomena like flow separation, flow transition, down-wash, stalling at the higher angle of attack, stalling velocity and how cambered airfoil can typically generate lift at a zero incidence angle. Most of all a mathematical model and the mechanism of streamline formation in an open-circuit laminar with respect to the shape and size of the body are illustrated.

What drives an individual police officer to activate his body-worn camera (BWC)? Some evidence suggests officer attitudes and resistance to the technology contributes to the equivocal results in studies testing for BWCs effect on use-of-force, complaints, and other outcomes of interest. Leveraging a novel survey and administrative dataset, we investigate the predictors of BWC activation among 147 police officers in a single agency. With a test of three nested models, we find job function covariates offer robust predictive power of how often an officer activates her or his BWC. Neither demographic nor attitudinal measures significantly predict BWC activations, except for a negative relationship with how officers perceive BWC impacts on professional discretion. The study furnishes empirical support for understanding officers as Principled Agents: job function, guided by administrative policy is the most explanatory and parsimonious, while models of attitudes and demographics fail to improve upon the job function model.

The primary and proven therapy, in cases of celiac disease (CD), is a rigorous gluten-free diet. However, there are reports of its negative effects in the form of nutritional deficiencies, obesity and adverse changes in body composition. The aim of the study was to assess the impact of a gluten free diet (GFD) on the body composition of children with CD. In a case-controlled study (n = 41; mean age 10.81 y; SD = 3.96) children with CD, in various stages of treatment, underwent medical assessment. The control group consisted of healthy children and adolescents, strictly matched for gender and age in a 1:1 case-control manner. More than half of the examined children (n = 26) followed a GFD. CD children had significantly higher mean values of the fat free mass (FFM% = 80.68 vs. 76.66, p = 0.015), and total body water (TBW% = 65.22 vs. 60.47, p = 0.012), and lower mean values of the fat mass (FM% = 19.32 vs. 23.34, p = 0.015). Children who were on a GFD presented slightly higher, but not statistically significant, mean values of FM and FFM, than children who did not follow dietary recommendations (FM [kg] = 7.48 vs. 5.24, p = 0.064; FM% = 20.81 vs. 16.73, p = 0.087; FFM [kg] = 28.19 vs. 22.62, p = 0.110). After minimum one year of a GFD, CD children showed significantly higher values of FFM [kg] (p = 0.001), MM [kg] (p < 0.001), TBW [L] (p < 0.001) and BCM [kg] (p < 0.001). Furthermore, CD children who were on a GFD presented significantly higher weight (p = 0.034) and body mass index (BMI) (p = 0.021) increase. The children adhering to a GFD demonstrate a tendency towards higher indices of selected body composition components.

Objective: To assess the effects of chronic walnut consumption on body weight and adiposity in elderly individuals. Methods: The Walnuts And Healthy Aging study is a dual-center (Barcelona, Spain and Loma Linda University [LLU]), 2-year randomized parallel trial. This report concerns only the LLU cohort. Healthy elders (mean age 69 y, 67% women) were randomly assigned to walnut (n = 183) or control diets (n = 173). Subjects in the walnut group received packaged walnuts (28–56 g/d), equivalent to ≈15% of daily energy requirements, to incorporate into their habitual diet, while those in the control group abstained from walnuts. Adiposity was measured periodically, and data were adjusted for in-trial changes in self-reported physical activity. Results: After 2 years, body weight significantly decreased (P = 0.031), while body fat significantly increased (P = 0.0001). However, no significant differences were observed between the control and walnut groups regarding body weight (−0.6 kg and −0.4 kg, respectively, P = 0.67) or body fat (+0.9% and +1.3%, respectively, P = 0.53). Lean body mass, waist circumference and waist-to-hip ratio remained essentially unchanged. Sensitivity analyses were consistent with the findings of primary analysis. Conclusion: Our findings indicate that walnuts can be incorporated into the daily diet of healthy elders without concern for adverse effects on body weight or body composition.

A basic pattern in the body plan architecture of many animals, plants and some molecular and cellular systems is five-part units. This pattern has been understood as a result of genetic blueprints in development and as a widely conserved evolutionary character. Despite some efforts, a definitive explanation of the abundance of pentagonal symmetry at so many levels of complexity is still missing. Based on both, a computational platform and a statistical spatial organization argument, we show that five-fold morphology is substantially different from other abundant symmetries like three-fold, four-fold and six-fold symmetries in terms of spatial interacting elements. We develop a measuring system to determine levels of spatial organization in 2D polygons (homogeneous or heterogeneous partition of defined areas) based in principles of regularity in a morphospace. We found that spatial organization of five-fold symmetry is statistically higher than all other symmetries studied here (three to ten-fold symmetries) in terms of spatial homogeneity. The significance of our findings is based on the statistical constancy of geometrical constraints derived from spatial organization of shapes, beyond the material or complexity level of the many different systems where pentagonal symmetry occurs.

The Ayers Rock of Australia which is known for its charming colors at different time is actually the Celestial Body Ring of the planet Earth that implies the great Celestial Body Love happened on Earth long long ago. The Tasmania island of Australia which is known for the World Heart is actually in the state of face to face with the main island of Australia, which implies the image spokesperson for the inner core (the heart) of the planet Earth. In other words, with the outline of the main island of Australia, the basic key information of the inner core of the planet Earth could be easily obtained by deducing logically, just like the similarity between the fists and heart of human body. Similar to the mechanism of the blood circulation dominated by the heart of human body, it is dominated and motivated by the inner core of the Earth which forms the circulation of mantle magma between the crust and the inner core, and what leads to the formation of expanding and active area on the equatorial and middle-lower latitude area and the silent and convergent area on the North and South Pole central area. Therefore, the mantle magma whirlpools under the crust on the North and South Pole are supposed to exist logically. The walking sideways of the crabs just implies the celestial body language of the motive trend of the main island of Australia based on their similar outline.

In our recent report, we clarified the direct interaction between excitatory amino acid transporter (EAAT) 1/2 and polyunsaturated fatty acids (PUFAs) by applying electrophysiological and molecular biological techniques to Xenopus oocytes. Xenopus oocytes have a long history of use in the scientific field, but they are still attractive experimental systems for neuropharmacological studies. We will therefore summarize the pharmacological significance, advantages, (especially in the study of EAAT2), and experimental techniques that can be applied to Xenopus oocytes; our new findings concerning L-glutamate (L-Glu) transporters and PUFAs; and the significant outcomes of our data. The data obtained from electrophysiological and molecular biological studies of Xenopus oocytes have provided us with further important questions, such as whether or not some PUFAs can modulate EAATs as allosteric modulators and to what extent docosahexaenoic acid (DHA) affects neurotransmission and thereby affects brain functions. By combining Xenopus oocyte experiments and more translational approaches, we can clarify the functions of proteins that are difficult to examine using cultured cells and the physiological roles of these proteins in brain functions. These approaches can lead to the development of the new central nervous system (CNS) drugs targeting molecules and investigations of their effectiveness.

In recent years, vision-centric perception has played a crucial role in autonomous driving tasks, encompassing functions such as 3D detection, map construction, and motion forecasting. However, the deployment of vision-centric approaches in practical scenarios is hindered by substantial latency, often deviating significantly from the outcomes achieved through offline training. This disparity arises from the fact that conventional benchmarks for autonomous driving perception predominantly conduct offline evaluations, thereby largely overlooking the latency concerns prevalent in real-world deployment. While a few benchmarks have been proposed to address this limitation by introducing effective evaluation methods for online perception, they do not adequately consider the intricacies introduced by the complexity of input information streams. To address this gap, we propose the Autonomous-driving Streaming I/O (ASIO) benchmark, aiming to assess the streaming inputs characteristics and online performance of vision-centric perception in autonomous driving. To facilitate this evaluation across diverse streaming inputs, we initially establish a dataset based on the CARLA Leaderboard. In alignment with real-world deployment considerations, we further develop evaluation metrics based on information complexity specifically tailored for streaming inputs and streaming performance. Experimental results indicate significant variations in model performance and ranking under different major camera deployments, underscoring the necessity of thoroughly accounting for the influences of model latency and streaming inputs characteristics during real-world deployment. To enhance streaming performance consistently across distinct streaming inputs features, we introduce a backbone switcher based on the identified streaming inputs characteristics. Experimental validation demonstrates its efficacy in perpetually improving streaming performance across varying streaming inputs features.

Automatic generation control (AGC) plays a vital role in creating an equilibrium between generated output power and load demand, in order to maintain frequency at desired value. This study focuses on performance analysis of simple-multi attribute rating technique (SMART) assisted proportional-integral-derivative (PID) controller design for AGC of two interconnected power systems. PID controller is designed by minimizing frequency variations, area control errors for area-1 and area-2, and tie-line power deviation. An objective function is framed considering error minimization of aforementioned factors as sub-objectives. The construction of objective function involves using the integral of time-multiplied absolute error (ITAE) for frequency deviations for area-1 and area-2, ITAE for deviation in tie-line power, and ITAEs for area control errors for area-1 and area-2 as sub-objective functions. By assigning appropriate weights to these sub-objective functions, an overall objective function is formed. This study determines these weights in an organized manner using SMART method, rather than randomly/equally assigning them. Overall objective function is minimized using Jaya algorithm. To demonstrate effectiveness of the proposed Jaya-based PID controller, its performance is analysed and compared with controllers tuned using other optimization algorithms, including sine cosine, Luus-Jaakola, teacher-learner based optimization, Nelder-Mead simplex, and elephant herding optimization. Considering six different case studies that consider a range of load variations, responses for fluctuations in frequency and tie-line exchange are plotted. Statistical and non-parametric analysis performed further provide additional insights into the performance of Jaya-based PID controller.

Recently, Electric Two-Wheelers ETW are changing the face of the global automotive market. This study focused on selecting proper material and mechanical isolation gap to design a protective enclosure for the battery pack of ETW. The integration of the Failure, Modes, Mechanism and Effect Analysis (FMMEA) method is utilized to develop the interface matrix and the severity index of different components of the enclosure. By analyzing different forces from the road conditions, dynamics during turn, acceleration, and deceleration with the enclosure, it becomes a crucial load-bearing element. Employing Finite Element Modeling (FEM), structural strength using materials like AL6061, Q235, C22000, DC 01 and Teflon are assessed under varying static, dynamic and thermal conditions. Modal analysis is conducted to observe the excitation frequencies where the maximum deformation for the metal enclosure is observed beyond 500Hz. AL6061 material that can withstand the stresses and deformations that are under allowable stress limits with negligible deformation is most preferable material based on the results. Minimal of 2.5 mm gap to be provided in case of metal casing and 10mm in case of Teflon is proven.

The cubic nonlinearity of graphene oxide (GO) monolayer was characterized by open and closed Z-scan using a nano-second laser of 10 Hz repetition rate with a Gaussian spatial beam profile. The reverse saturable absorption or positive nonlinearity from open Z-scan and valley-peak traces or positive nonlinearity from closed Z-scan was displayed. The reverse saturable absorption could be from a two-photon or two-step excitation process due to the larger absorption in the lower visible and upper UV wavelength region compared with the excitation source. The nonlinear absorption and nonlinear refraction coefficient were estimated to be ~ 2.62x10-8 m/W and 3.9x10-15 m2/W, respectively. This study also reveals the effect of nonlinear absorption on nonlinear refraction traces.

The invariant mass of free particles is used to derive a bound-state equation for several particle atomic systems at rest. This relativistic-kinematic bound-state equation is applied to the hydrogen and helium atoms. The derived equation has the well-known solutions for the single-electron bound states of the hydrogen atom, and the two-electron states of the helium atom. For the hydrogen atom, existence of the two-particle bound states, for which the electron and the proton kinetic energies are of the same order of magnitude, is predicted. The three-particle bound states with the same feature of the kinetic energies can exist in the helium atom. Radiative operators for processes involving the hydrogen two-particle bound states, are obtained. It is discussed that these new two- and three-particle bound states should be optically inactive.

In recent years, drones have been used in a wide range of fields such as agriculture, transportation of goods, and security. Drones equipped with communication facilities are expected to play an active role as base stations in areas where ground base stations are unavailable, such as disaster areas. In addition, asynchronous operation is being considered for local 5G in order to support all kinds of use cases. In asynchronous operation, cross-link interference between base stations is an issue. This paper attempts to reduce the interference caused by the drone network by introducing circularly polarized antennas. Numerical analyses are conducted to validate the effectiveness of the proposed system, where SIRs (Signal-to-Interference Ratio) are shown to be improved significantly as the numerical evaluation results.

This paper proposed a time two-mesh (TT-M) finite difference numerical scheme to improve the efficiency of solving the symmetric regularized long wave (SRLW) equation. The TT-M Crank-Nicolson discretization and finite difference method are employed in time and space approximation respectively. The scheme involves three main steps: firstly, the time interval is divided into coarse and fine time meshes, then the nonlinear system is solved on the coarse time mesh; secondly, coarse numerical solutions on the fine time mesh are computed using an interpolation formula based on the solutions derived in the step one; lastly, the TT-M finite difference numerical solutions can be obtained through constructing the linearized fine time mesh system using Taylor’s formula. Compared to the currently existing TT-M numerical methods, the novelty of this study is that the nonlinear term including derivatives is linearized by Taylor’s formula for a function with three variables, whose error analysis is more complex. Finally, some numerical examples, including computational time and accuracy, preservation of conservation laws, are given to verify the efficiency of the scheme. By comparing it with the standard nonlinear finite difference scheme, this method can reduce CPU time without sacrificing accuracy.

Manufacturers of photovoltaic modules do not provide all the information necessary to predict their performance under different climatic conditions. This forces the development of mathematical models of behavior and the application of mathematical methods for the calculation of their associated parameters. A toolbox called PVMSim implemented in MATLAB/GUI is proposed in this paper. PVMSIm provides models allowing the simulation of photovoltaic modules. A two-diode model is used to represent the effect of irradiance and temperature on the V-I and V-P characteristic curves. The accuracy of PVMSim has been vaildated by applying the models to two mono-crystalline and multi-crystalline solar modules of different power ratings and manufacturers. The model PVMSim model accuracy was verified against the manufacturer’s datasheet. This paper shows that this tool is useful for designers and professionals who require an intuitive graphical interface for fast and accurate modeling, simulation and sizing of photovoltaic systems.

This paper presents a concise mathematical framework for investigating both feed-forward and backward process, during the training to learn model weights, of an artificial neural network (ANN). Inspired from the idea of the two-step rule for backpropagation, we define a notion of F_adjoint which is aimed at a better description of the backpropagation algorithm. In particular, by introducing the notions of F-propagation and F-adjoint through a deep neural network architecture, the backpropagation associated to a cost/loss function is proven to be completely characterized by the F-adjoint of the corresponding F-propagation relatively to the partial derivative, with respect to the inputs, of the cost function.

As development progresses, when the bottom hole flowing pressure or formation pressure is less than the saturation pressure of crude oil in the reservoir, oil and gas two-phase seepage occurs in the reservoir. Due to the characteristics of oil and gas two-phase seepage, after the oil and gas two-phase seepage occurs in the reservoir, the well production will be reduced, or even greatly reduced. Therefore, how to predict the horizontal well capacity better in this case is an important problem that needs to be solved urgently. In this paper, the method and process of establishing the transient calculation model of two-phase flow in horizontal wells are introduced in detail from three aspects: fluid physical properties, reservoir oil-gas two-phase seepage, and the coupling model of Inflow Performance and Flow in Wellbore. The model is more reliable through the verification of production data from five wells in two oilfields.

The unsteady flow around the monopile under the influence of wave and vibration is studied by numerical method. Based on VOF model and SST Turbulence model, combined with Intermittent Transition model and dynamic mesh method, wave generation and pile vibration in numerical flume are simulated. The flow field around vibrating monopile in a calm water flume and a wave flume is simulated and the simulation results are compared. The calculation results show that the monopile vibration has a great disturbance to the unsteady flow around the pile, and the disturbance degree intensifies with the increase of the vibration amplitude of the monopile: Under the action of inertia, the vibration of the monopile leads to the reattachment of the shedding vortices; Under the influence of the reattachment vortices, the asymmetry of the vorticity on the side wall of the monopile intensifies; The intensification of the disturbance causes the reduction of the phase lead angle of the bed shear stress on the side of the single pile, and an additional high bed shear stress appears on the side of the monopile. In addition, the vortex structure formed alternately around the monopile during the vibration process leads to the periodic change of the high bed shear stress.

State transition in the multiple-levels system has the great potential applications in the quantum technology. In this article we employ a deterministic approach in complex space to analyze the dynamics of the 1s-2p electron transition in the hydrogen atom. The electron’s spin motion is embodied in the framework of quantum Hamilton mechanics that allows us to examine the transition dynamics more precisely. The transition is driven by an oscillating electric field in the z-direction. The electron’s transition process can be visualized by monitoring its motion in the complex space. The quantum potential and the total energy proposed in this paper provide new indices to observe the dynamic changes of electrons in the transition process.

Gravel packing completion method for horizontal wells has the advantages of maintaining high oil production for a long time, maintaining wellbore stability and preventing sand production, so it has become the preferred completion method for horizontal wells. At present, this technology still faces the problems of high sand bed height and poor gravel migration. In order to improve the efficiency of gravel packing in horizontal wells, pulsed gravel packing technology for horizontal wells is proposed for the first time. Based on the mechanism of hydraulic pulse, the Eularian model, RNG K-ε model and CFD model are used to simulate the solid-liquid two-phase flow. By optimizing the parameters such as frequency and amplitude of pulse waveform, the optimal pulse waveform of pulsed gravel packing in horizontal wells is determined. The effects of parameters such as sand-carrying fluid displacement, sand-carrying fluid viscosity, sand-carrying ratio, gravel particle size and string eccentricity on pulsed gravel packing in horizontal wells are studied, and the distribution law of gravel migration velocity and volume fraction in horizontal wells is obtained. According to the results, it can be seen that with the increase of displacement and viscosity of carrier fluid, the volume fraction of fixed bed and moving bed decreases gradually, while that of suspension bed increases gradually. With the increase of sand-carrying ratio, gravel particle size and string eccentricity, the volume fraction of fixed bed and moving bed increases gradually, while that of suspended bed decreases gradually. Comparing the effects of conventional gravel packing and pulsed gravel packing in horizontal wells, it can be concluded that the efficiency of pulsed gravel packing in horizontal wells is higher. The volume fraction of fixed bed and moving bed decreased by 30% and 40% respectively, while the volume fraction of suspended bed increased by 20%. The migration velocity of moving bed and suspended bed increased by 40% and 25% respectively. And the migration ability of gravel improved obviously.

We search for limit cycles in the dynamical model of two-species chemical reactions that contain seven reaction rate coefficients as parameters and at least one third-order reaction step, that is, the induced kinetic differential equation of the reaction is a planar cubic differential system. Symbolic calculations were carried out using the Mathematica (or, Wolfram language) mathematical program package, and it was also used for the numerical verifications to show the following facts: the kinetic differential equations of these reactions each has two limit cycles surrounding the stationary point of focus type in the positive quadrant. In the case of Model 1, the outer limit cycle is stable and the inner one is unstable that appears in a supercritical Hopf bifurcation. Moreover, the oscillations in a neighborhood of the outer limit cycle are slow-fast oscillations. In the case of Model 2, the outer limit cycle is unstable and the inner one is stable. With another set of parameters, the outer limit cycle can be made stable and the inner one unstable.

In passing maneuvers on two-lane highways, assessing the needed distance and the potential power reserve to ensure the required speed mode of the passing vehicle is a critical task of speed planning. This task must meet several mutually exclusive conditions that lead to successful maneuver. The paper addresses three main aspects. First, the issues of rational distribution of the speed of the passing vehicle for overtaking a long commercial vehicle on two-lane highways are discussed. The factors that affect maneuver effectiveness are analyzed, considering safety and cost. Second, a heuristic algorithm is then proposed based on the rationale for choosing the necessary space and time for overtaking. The initial prediction's sensitivity to fluctuations of current measurements of the position and speed of the overtaking participants is examined. Third, an optimization technique for passing vehicle speed distribution over the overtaking time using the finite element method is presented. The adaptive model predictive control is applied for tracking the references being generated. The presented model is illustrated using simulation.

In this paper, a numerical modeling of the impact, spreading, and eventually rebound of a viscoelastic droplet is reported. The numerical model is based on the volume of fluid (VOF) method coupled with the FENE-CR constitutive equations, and accounts for both the surface tension and the substrate wettability. The FENE-CR constitutive equations are used to model the polymer solution, while taking advantage of its rheological characterization. The comparison is performed between droplets of Newtonian solvent and a monodisperse polymer solution. The droplet impact on both hydrophilic and superhydrophobic substrate is analyzed through a detailed analysis of the spreading diameter evolution. It is found that while the droplet kinematic phase seems independent of the substrate and fluids properties, the recoiling phase is highly related to all of them. In addition, the model infers a critical polymer concentration above which the droplet rebound from a superhydrophobic substrate is suppressed. The simulation is of particular interest to ink-jet processing, and demonstrates the capability of the model to handle complex non-Newtonian droplet dynamics.

Measurement-Device-Independent Quantum Key Distribution (MDI-QKD) is a two-photon protocol devised to eliminate eavesdropping attacks that interrogate or control the detector in realized quantum key distribution systems. In MDI-QKD, the measurements are carried out by an untrusted third party, and the measurement results are announced openly. Knowledge or control of the measurement results gives the third party no information about the secret key. Error-free implementation of the MDI-QKD protocol requires the crypto-communicating parties, Alice and Bob, to independently prepare and transmit single photons that are physically indistinguishable, with the possible exception of their polarization states. In this paper, we apply the formalism of quantum optics and Monte Carlo simulations to quantify the impact of small errors in wavelength, bandwidth, polarization and timing between Alice's photons and Bob's photons on the MDI-QKD quantum bit error rate (QBER). Using published single-photon source characteristics from two-photon interference experiments as a test case, our simulations predict that the finite tolerances of these sources contribute (4.04+/-20/N_sifted) to the QBER in an MDI-QKD implementation generating an N_sifted-bit sifted key.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

This paper investigates the influence of magnetic field for a two dimensional deformations on a two temperature problem at the free surface of a semi-infinite semiconducting medium under the effect of mechanical force during a photothermal theory and the effect of hydrostatic initial stress on the medium. The Harmonic Wave Method (Normal Mode Analysis) has been used to obtain the equations of elastic waves, heat conduction equation, quasi-static electric field, carrier density, two temperature coefficient, ratios, and constitutive relationships for the thermo-magnetic-electric medium. The effects of several parameters as thermoelastic and thermoelectric coupling parameters and two temperature parameter of this force on the displacement component, force stress, carrier density and temperature distribution has been depicted graphically.

Lean body mass (LBM) is correlated with powerlifting performance in athletes competing in different bodyweight classes. However, it remains unknown whether changes in LBM are correlated with performance changes in powerlifters preparing for a competition. Aim of the study was to investigate the changes in LBM and performance in powerlifters preparing for a competition. Eight male powerlifters (age 31.7±9.8years, height 1.77±0.06m, weight 99.2±14.6kg) and three female powerlifters (age 32.7±16.3years, height 1.54±0.06m, weight 66.6±20.9kg), participated in the study. Athletes followed individualized periodized training programs for 12 weeks aiming to maximize their performance for the national championship. Maximum strength (1-RM) in squat, bench press, and deadlift, body composition, grip strength, anaerobic power, quadriceps’ cross sectional area and vastus lateralis muscle architecture were measured before and after the training period. Significant increases were found after the training period in squat (5.8±7.0%, P

Urinary tract diseases are common in cats, and often require surgical reconstruction. Here, to explore the possibility of urinary tract reconstruction in cats using in-vivo tissue architecture (iBTA), biosheets fabricated using iBTA technology were implanted into the feline bladder and the regeneration process was histologically evaluated. The biosheets were prepared by embedding molds into the dorsal subcutaneous pouches of six cats for 2 months. A section of the bladder wall was removed, and the biosheets were sutured to the excision site. After 1 and 3 months of implantation, the biosheets were harvested and evaluated histologically. Implantable biosheets were formed with a success rate of 67%. There were no major complications following implantation, including tissue rejection, severe inflammation, or infection. Urinary incontinence was also not observed. Histological evaluation revealed the bladder lumen was almost entirely covered by urothelium after 1 month, with myofibroblast infiltration into the biosheets. After 3 months, the urothelium became multilayered, and mature myocytes and nerve fibers were observed at the implantation site. In conclusion, this study showed that tissue reconstruction using iBTA can be applied to cats, and that biosheets have the potential to be useful in both the structural and functional regeneration of the feline urinary tract.

Abstract: Congenital cytomegalovirus (cCMV) infection poses significant risks to fetal development, particularly affecting the nervous system. This study reports a fetal autopsy case, examining cCMV infection and focusing on CMV DNA measurements in various fetal organs before formalin fixation, a novel approach for comprehensive CMV DNA evaluations in fetal organs affected by cCMV. A 20-week-old male fetus was diagnosed with cCMV following the detection of CMV DNA in ascites obtained via abdominocentesis in utero. After termination of pregnancy, multiple organs of the fetus, including the cerebrum, thyroid gland, heart, lungs, liver, spleen, kidneys, and adrenal glands, were extracted and examined for CMV DNA loads using real-time polymerase chain reaction. Histopathological examination involved hematoxylin-eosin and CMV-specific immunostaining. A correlation was found between CMV DNA loads and pathology, with higher CMV-infected cell numbers observed in organs positively identified with both staining methods, exhibiting CMV DNA levels of ≥1.0 × 104 copies/mL, compared to those detected solely by CMV-specific immunostaining, where CMV DNA levels ranged from 1.0 x 103 to 1.0 x 104 copies/mL. These results highlight a quantifiable relationship between organ infection extent and CMV DNA concentration, providing insights into cCMV pathogenesis and potentially informing future diagnostic and therapeutic strategies for cCMV infection.

Diabetes is one of the fastest spreading diseases of civilisation in the 21st century. The aim of the study was twofold: 1) to find differences in personality traits, self-esteem, body- esteem, and imagery between healthy women and women with diabetes 2) to check whether there are differences in analyzed factors in women with diabetes who participate in sports compared to women who do not. We used 3 questionnaires: Imagination: in sport - short form, Self-Esteem Scale (SES), and BFIS Personality, which were tested online. We found that women with diabetes were characterised by significantly higher neuroticism and lower extraversion and higher conscientiousness (marginally significant). We also found that women with diabetes who practice sport rated their bodies more highly in terms of sexual attractiveness and made better use of imagined affirmations than healthy women who were not active. Our study provides new insights into diabetics in terms of coping with the disease.

Introduction: While preparing for dive exams, divers are trained to perform rescue exercises. Currently, divers think they will manage and control their body at any time.Methods: At the bottom of the water, the student takes the instructor who simulates a sickness, up to the surface, by controlling the going up. Then, if the exercise is wrong, both divers go down and exercise again. If the exercise is successful, both divers go down to perform another exercise until they are tired or until they have no more air. Results: I discovered that there was a mistake in the preparation of divers for rescue training due to Descartes’ error, “I think, thus I am”, which is part of our collective memory. Going up and going down after a sickness simulation is a repetitive action of the body and going down is therefore part of the automatisms of rescue, which is very dangerous. Conclusions: The body is not necessarily controlled by the present thinking, and if divers forget sickness while going up in a real rescue situation, they will go down automatically because their bodies were trained like this. In addition, it is very easy to forget sickness. Divers should not go down after rescue, they should be on the dive boat or on the land. Descartes’ error has to be reversed: “I am, thus I think” is right. The divers’ rescue exercises must be simplified and divers should never go down after the simulation of a sickness.

Treatment options for sarcopenia are currently limited, primarily relying on two main therapeutic approaches: resistance-based physical activity and dietary interventions. However, details about specific nutrients in the diet or supplementation are unclear. Our objective is to investigate the relationship between nutrient intake and lean mass, function, and strength. Data were derived from the Gothenburg H70 birth cohort study in Sweden, including 719 70-year-olds born in 1944 (54,1 % females). For independent variables, the diet history method (face-to-face interviews) was used to estimate habitual food intake during the preceding three months. Dependent variables were gait speed (muscle performance), hand grip strength (muscle strength) and appendicular lean soft tissue index (ALSTI). Linear regression analyses were performed to analyze the relationship between the dependent variables and each of the covariates. Several nutrients were positively associated with ALSTI, such as polyunsaturated fatty acids (DHA, EPA), selenium, zinc, riboflavin, niacin equivalent, vitamin B12, vitamin D, iron, and protein. After correction for multiple tests, there were no remaining correlations with handgrip and gait speed. Findings of positive correlations for some nutrients with lean mass suggest a role for these nutrients for maintaining muscle volume. These results can be used to inform clinical trials to expand the preventive strategies and treatment options for individuals at risk of muscle loss and sarcopenia.

. (1) Background: The aim of this study was to verify the differences in body composition, power and lower limb muscle strength in futsal players from three competitive levels. (2) Methods: The study involved 68 players (24.26 ± 4.63 years), divided into three competitive levels: elite, sub-elite and amateur. To assess physical condition, we used the Inbody270, the ChronoJump and the Isokinetic Dynamometer and used the non-parametric Kruskal-Wallis test to compare the three independent variables. (3) Results: There were no differences in body composition between the players at the three competitive levels. With regard to lower limb muscle power and strength, the elite group showed, on average, better performance and capabilities, especially when compared to the amateur group, and all groups showed an H/Q ratio &gt; 60%. (4) Conclusions: We conclude that there are not many differences in physical condition between the three competitive levels of futsal, despite the unequal sporting demands between them. However, the elite group has greater power and muscle strength, and both groups showed a high probability of lower limb muscle injury at this stage of the sporting season, alerting sports training professionals to the importance of individualized analysis of physical condition and performance capacity.

Lung cancer remains the leading cause of cancer-related mortality worldwide. The main issue is the absence of a screening test available in clinical practice; the identification of non-invasive biomarkers is thus an urgent clinical necessity. Currently, low-dose computed tomography (LD-CT) demonstrates a 20% reduction of lung cancer mortality. However, it is not particularly suitable for clinical practice because of the costs, radiation, and the false positive rate. Several studies have therefore focused on research into biomarkers in body fluids. Despite the power of certain molecules to distinguish lung cancer patients from healthy subjects, no biomarker has yet been shown to significantly and reliably influence clinical decisions or to be translated from the laboratory to clinical practice. We performed an overview of the peer-reviewed biomedical literature published in the last 10 years on the research regarding biomarkers for the early diagnosis of lung cancer via a comprehensive analysis of the reviews published this past year. Our main aim was to bring to light the limitations and strengths of the research already conducted. Furthermore, future prospectives have been explored, bearing in mind the management of clinical trials and their integration into clinical practice.

The association between obesity and clinical as well as radiological outcomes in patients suffering non-traumatic intracerebral haemorrhage (ICH) remains unclear. The obesity paradox suggests a protective effect regarding in-hospital mortality. This study evaluates the impact of body mass index (BMI) on functional long-term outcome and bleeding volume in patients with non-traumatic ICH. A retrospective cohort study including all consecutive patients with spontaneous ICH treated at a tertiary referral centre between December 2017 and June 2021, aged 80 years or younger (n = 218), were included. Patients were dichotomized into overweight (OW, BMI ≥ 25 kg/m2) and normal weight (NW, BMI < 25 kg/m2). Functional outcomes were assessed by the modified Rankin scale (mRS), extended Glasgow Outcome Scale (GOS-E) and the National Institutes of Health Stroke Scale score (NIHSS) at 1, 3, 6 and 12-months follow-up. Bleeding volumes were calculated as ABC/2. Univariate and multivariate analysis were performed to assess clinical predictors of favourable outcome in the long-term. Of 218 patients (66.04 ± 15.18 years) suffering non-traumatic ICH, 115 (52.75%) were OW (29.72 ± 3.82). Female sex (p = 0.1), NIHSS (p = 0.69), cardiovascular risk factors (p = 0.55), ICH volume (p = 0.19), and presence of anticoagulation (p = 0.67) did not significantly differ between the OW and NW cohort. At discharge, functional outcome did not significantly differ between both cohorts (NW, mRS 3.92 ± 2.54 vs. OW, mRS 3.21 ± 2.43, (p = 0.28)). Multivariate analysis revealed that haemorrhage volume (p = 0.01) was the only robust risk factor to predict functional outcome after 1 year. Our data suggests that in ICH patients, neither obesity nor patient’s age are negative predictors for functional outcome in the long-term. Instead, bleeding volume is a robust risk factor predicting poor functional status after ICH. Therefore, prospective randomized trials analysing this coherence are highly warranted.

Crossbreeding in dairy cattle with exotic breeds continues to be an appealing practice to the dairy farmers of Bangladesh. However, there is limited knowledge regarding the impact of crossbreeding on both the physical attributes and milk quality traits of crossbred cattle in Bangladesh. Therefore, the primary objective of this study was to evaluate the impact of crossbreeding Bangladeshi local cattle with the exotic Holstein breed on their body characteristics and milk quality. To achieve the goal, data pertaining to body traits and milk samples were gathered from a total of 981 cows from 19 dairy farms located in the northwestern region of Bangladesh. A trained evaluator measured body condition score (BCS), udder score, locomotion score, and body conformation traits. Milk yield information was acquired from official records, while milk composition details were determined through milk analysis. The average measurements for body traits were as follows: wither height (WH) at 138 cm, body length (BL) at 155 cm, and heart girth (HG) at 203 cm. Notably, crossbred cows (Holstein x Local cattle) exhibited greater values for WH, BL, HG, BCS, and udder score than their Bangladeshi local counterparts. Furthermore, the average daily milk yield of sampled cows was recorded at 8.7 kg, with fat and protein contents of 3.78% and 3.67%, respectively. It is worth noting that crossbred cows produced a higher volume of milk compared to Bangladeshi local cattle. However, milk from crossbred cows displayed lower fat and protein content, although their somatic cell score (SCS) remained similar. Additionally, milk from crossbred cows exhibited a longer coagulation time when compared to that of Bangladeshi local cattle. A more comprehensive assessment of the crossbreeding scheme, particularly in comparison to Holstein, would necessitate further research, including an examination of its impact on cheese yield traits, health, fertility, and longevity.

Body composition measurement plays an important auxiliary role in the nutritional assessment of diseases, nutritional diagnosis and the evaluation of the effect of nutritional therapy. There are many techniques and methods available for the measurement of body composition. Bioelectrical impedance analysis (BIA ) of body composition has been widely used and explored in many diseases in the past 30 years. Its main advantages are its non-invasiveness, non-radiation, economy, convenience and feasibility. With the development of bioelectrical impedance technology, bioelectrical impedance analysis has gradually developed from single-frequency BIA (SF-BIA) to dual-frequency BIA (DF-BIA). now devices are available that measure at multiple fixed frequencies (multi-frequency BIA, MF-BIA) and over a range of frequencies (bioimpedance spectroscopy, BIS). The clinical significance of nutrition management in chronic kidney disease has gradually become prominent. Bioelectrical impedance analysis of body composition is favored by nephrologists and nutritionists as an auxiliary method for nutrition diagnosis, treatment and monitoring. In the past 20 years, there have been many studies on body composition measurement by bioelectrical impedance analysis in the nutritional management of CKD patients. This article will summarize the recent research results of BIA of body composition method in the nutrition management of CKD patients in pre-dialysis, hemodialysis, peritoneal dialysis and kidney transplantation, in order to provide reference for the application and research of BIA method in the nutrition management of chronic kidney disease in the future.

Round bodies in spirochete cultures have been a controversial subject since their description seven decades ago. We report the existence of round bodies (spherical cells) in cultures of Mucispirillum schaedleri, a spiral bacterium phylogenetically distant from spirochetes. Furthermore, when grown in biofilms, M. schaedleri demonstrates a unique morphology known as cording, which has been previously described only in mycobacteria. Thus, M. schaedleri has two distinct features, each previously thought to be unique to two different phylogenetically distant groups of bacteria.

Outbreaks of Anticarsia gemmatalis (Hübner, 1818) (Lepidoptera: Erebidae), a major pest of soybean, can be controlled below economic thresholds with methods that do not involve the application of synthetic insecticides. Formulations based on natural isolates of the Anticarsia gemmatalis multiple nucleopolyhedrovirus (AgMNPV) (Baculoviridae: Alphabaculovirus), played a significant role in integrated pest management programs in the early 2000s, but a new generation of chemical insecticides and transgenic soybean, have displaced AgMNPV-based products over the past decade. However, the marked genotypic variability present among and within alphabaculovirus isolates suggests that highly insecticidal genotypic variants can be isolated and used to reduce virus production costs or overcome isolate-dependent host resistance. This study aimed to select novel variants of AgMNPV with suitable insecticidal traits that could comple-ment the existing AgMNPV active ingredients. Three distinct AgMNPV isolates were compared by restriction endonuclease profile and in terms of their occlusion body (OB) pathogenicity. One isolate was selected (AgABB51) from which eighteen genotypic variants were plaque purified and characterized in terms of their insecticidal properties. The five most pathogenic variants varied in OB pathogenicity although none of them was faster-killing or had higher OB production characteristics than the wild-type isolate. We conclude that the AgABB51 wild-type isolates ap-pear to be genotypically structured for fast speed-of-kill and high OB production, both of which would favor transmission. Interactions among the component variants are likely to influence this insecticidal phenotype.

(1) Background: This article presents a study that aims to provide a precise understanding of the temperature distribution within a Whole-Body Cryostimulation (WBC) chamber, whether it is empty or occupied by one or several individuals.; (2) Methods: The study employs a mixed numerical and experimental approach, utilizing simplified Computational Fluid Dynamics (CFD) simulations and an experimental analysis that employs thermocouples to determine the 3D thermal field in actual conditions.; (3) Results: The results reveal a non-negligible temperature difference between the setpoint and actual temperature in the middle of the cryochamber. Furthermore, it is shown that the presence of individuals inside the chamber results in both an average temperature rise and a more heterogeneous thermal behavior, which appear to be associated with the number of individuals present.; (4) Conclusions: The findings of this study emphasize the need for further research to establish temperature guidelines and standardize measurement methods for effective WBC treatment.

The acquisition of regional, 1 metre resolution LIDAR in the PNG Highlands combined with 3D modelling in MoveTM has revolutionized our understanding of the evolution of the Porgera gold mine and areas of new potential. The new 3D model demonstrates active pull-apart basins along a regional transfer during ongoing fold and thrust deformation. When overlain on regional aeromagnetic data, new potential is revealed. The Porgera gold mine is one of the richest in the world and lies in a wide valley at an elevation of 2800m surrounded by mountains up to 4000m high in the middle of the PNG Highlands. It lies along a major lineament, the Porgera Transfer Zone (PTZ), cutting across the orogen that is associated with a 50 km offset of the ophiolite belt. To the NW of the mine there is an extensive belt of low- to high-grade metasediments that formed in deep water during Jurassic rifting, but were metamorphosed during Eocene subduction to the north. Subduction ceased due to accretion of the Sepik Terrane which caused inversion and mild erosion of the Porgera area. The Late Oligocene onset of wrenching in the Mobile Belt to the north placed that area into extension, emplacing metamorphic core complexes, and led to regional subsidence in the Early Miocene. Collision of the margin with the Melanesian Arc in the Middle Miocene caused Late Miocene to Pliocene orogenesis creating the broad mountain belt that we see today, that is still active, as shown by the 2018 MW 7.5 earthquake. Regional mapping of the area using high resolution LIDAR in association with limited field mapping, analysis of gravity and magnetics data and drilling of 300-500m deep core-holes has allowed development of a detailed 3D structural model. The Porgera valley is constrained laterally by the Eastern Boundary and Western Boundary dextral strike-slip faults that lie along the PTZ cutting across the orogeny. However, whilst the position and nature of the faults is clear, due to bending, fracturing and offset of major synclines and anticlines, the faults do not crop-out as significant through-going features. Rather, the dextral offset of basement is soft-linked to the Tertiary limestones at surface due to intervening thick, ductile Cretaceous shales. Fold and thrust structures are ubiquitous in the Tertiary limestones, but the youngest structural features are large extensional faults, particularly around the Porgera valley. The intrusive underlying the Porgera ore-body was emplaced at 6.0+-0.3 Ma, the time of maximum compression during orogenesis. At this time the Eastern Boundary fault and Western Boundary fault were both active allowing a pull-apart basin to form locally along the PTZ at the south-eastern boundary of the Jurassic metasediments. This enabled emplacement of the intrusive. The gold-bearing fluids from the intrusive and metasediments were brought up through the Mesozoic muds to the contact with the Paleogene carbonates where the Porgera ore body was emplaced.

The objective was to evaluate the metabolic and performance differences in primiparous Nellore cows, which became pregnant at 14 or 24 months. Thirty-eight primiparous Nellore cows, which were bred for first pregnancy at 14 or 24-mo of age, with 202 ± 5 days of gestation were divided into two treatments according to breeding age: 14 or 24 months in the breeding season. Cows were evaluated for weight, body condition score (BCS), carcass characteristics, milk yield and blood parameters: glucose, total proteins, albumin, urea, beta-hydroxybutyrate (β-OHB), non-esterified fatty acids (NEFA), progesterone, and for insulin-like growth factor-1 (IGF-1). There was an in-teraction (p < 0.01) between age at first pregnancy and time for body weight, where 24-mo cows were heavier, but both categories loss weight at parturition which concomitant decrease in the BCS (p < 0,01). However, BW of 24-mo remained stable (p > 0.05) after parturition. Milk yield was higher in 24-mo cows (p < 0.01). Interaction between sampling time and breading age was observed for Longissimus muscle area (p < 0.01) and tended for Longissimus muscle depth, where 24-mo cows had greater values in prepartum. Calves born from the cows bred at 24-mo, where was higher (p < 0.01) from 160 days of age until weaning at 240 days. Glucose, urea, total proteins, albumin and NEFA were affected (p < 0.01) by the parturition data-point. There was an interaction (p < 0.01) between breading age and sampling period for β-OHB. Progesterone concentration was greater in 24-mo cows (p < 0.01). It was concluded that primiparous cows that became pregnant at 14 or 24 months of age have different nutritional and metabolic responses.

Background: This study explored the effects of a virtual reality exercise program on overweight middle-aged women. Methods: This randomized controlled trial included women 4065 years of age with a body mass index (BMI) of 23 kg/m2 or more living in D city. The virtual reality environment was set up by attaching an IoT sensor to an indoor bicycle and linking it with a smartphone, enabling exercise in an immersive virtual reality through a head-mounted display. Results: In the virtual reality exercise group, the BMI was significantly decreased after the 8-week intervention compared with the baseline value (F=100.806, p<.001). The depression scores were significantly different among the three groups, with the intervention effect being more significant in the virtual reality exercise group than in the indoor bicycle exercise and con-trol groups (F=3.462, p<.001). Furthermore, the levels of exercise fun (F=12.373, p<.001) and exer-cise immersion (F=14.629, p<.001) were significantly higher in the virtual reality exercise group than in the indoor bicycle exercise and control groups. Conclusions: The virtual reality exercise program positively affected the BMI and the levels of depression, exercise fun, and exercise im-mersion in overweight middle-aged women. It is an effective home exercise program for obesity management in this population.

Currently, algae arouse a growing interest in the pharmaceutical and cosmetic area due to the fact that they have a great diversity of bioactive compounds with the potential for pharmacological, cosmetic, and nutraceutical applications. Many of these bioactive compounds are secondary metabolites whose amounts in the algae vary with varying environmental conditions. Free radicals and other active oxygen derivatives are recognized as a natural by-product of aerobic metabolism. However, reactive oxygen species directly participate in mechanisms related to various pathological states such as cancer, diabetes, atherosclerosis, Alzheimer's, and Parkinson's, among others. Diabetes mellitus (DM) is a metabolic disease resulting from changes in glucose metabolism and/or deficient production/action of insulin. This review has as its main objective to reveal the potential antioxidant and antidiabetic capacity of algae extracts.

Background: Some studies have shown that an increase in visceral fat is associated with postoperative clinical and oncologic outcomes. However, no studies have used bioelectrical impedance analysis (BIA) to determine the effects of visceral fat on the oncologic outcomes of colorectal cancer (CRC). This study aimed to investigate the relationship between visceral fat area (VFA) and clinical, and oncologic outcomes in CRC. Methods: This study included 203 patients who underwent anthropometric measurements by BIA before surgical treatment for CRC between January 2016 and June 2020. Results: According to the cutoff level of VFA by receiver operating characteristic curve analysis, 85 (40.5%) patients had a low VFA, and 119 (59.5%) had a high VFA. Multivariate analysis found that preoperative CRP (hazard ratio [HR], 3.882; 95% confidence interval [CI], 1.001–15.051; p=0.050) and nodal stage (HR, 7.996; 95% CI, 1.414–45.209; p=0.019) were independent prognostic factors for overall survival, while sex (HR, 0.110; 95% CI, 0.013–0.905; p=0.040), lymphovascular invasion (HR, 3.560; 95% CI, 1.098–11.544; p=0.034), and VFA (HR, 4.263; 95% CI, 1.280–14.196; p=0.040) were independent prognostic factors for disease-free survival (DFS). Conclusion: High VFA preoperatively measured by BIA was associated with inflammations and was an independent prognostic factor for DFS.

According to known laws of physics, chronic positive mass balance is the actual etiology of obesity, not positive energy balance. The relevant physical law in terms of body mass regulation is the Law of Conservation of Mass, not the Law of Conservation of Energy. A recently proposed mass balance model (MBM) describes the temporal evolution of body weight and body composition under a wide variety of feeding experiments, and it seems to provide a highly accurate description of the very best experimental human feeding data. By shifting to a mass balance paradigm of obesity, a deeper understanding of this disease may follow in the near future. The purpose of this living review is to present the core issues of the upcoming paradigm shift as well as some practical applications related to the topic.

In order to solve the labor-intensive and time-consuming problem in the process of measuring yak body ruler and weight in yak breeding industry in Qinghai Province, a non-contact method for measuring yak body ruler and weight was proposed in this experiment, and key technologies based on semantic segmentation, binocular ranging and neural network algorithm were studied to boost the development of yak breeding industry in Qinghai Province. Main conclusions: (1) Study yak foreground image extraction, and implement yak foreground image extraction model based on U-net algorithm; select 2263 yak images for experiment, and verify that the accuracy of the model in yak image extraction is over 97%. (2) Develop an algorithm for estimating yak body ruler based on binocular vision, and use the extraction algorithm of yak body ruler related measurement points combined with depth image to estimate yak body ruler. The final test shows that the average estimation error of body height and body oblique length is 2.6%, and the average estimation error of chest depth is 5.94%. (3) Study the yak weight prediction model; select the body height, body oblique length and chest depth obtained by binocular vision to estimate the yak weight; use two algorithms to establish the yak weight prediction model, and verify that the average estimation error of the model for yak weight is 10.7% and 13.01% respectively.

Background: Different drugs damage the frontal cortices, particularly the prefrontal areas involved in both emotional and cognitive functions, with a consequence of decoding emotion deficits for people with substance abuse. The present study aims to explore the cognitive impairments in drug abusers through facial, body and disgust emotion recognition, expanding the investigation of emotions, processing, measuring accuracy and response velocity. Method: We enrolled 13 addicted to cocaine and 12 alcohol patients attending treatment services in Italy, comparing them with 33 matched controls. Facial emotion and body posture recognition tasks, a disgust rating task, and the Barrat Impulsivity Scale were included in the experimental assessment. Results: We found that emotional processes are differently influenced by cocaine and alcohol, suggesting that these substances impact diverse cerebral systems. Conclusion: The contribution made by the duration of consumption on emotional processing seems far less important than for cognitive processes. Drug abusers seem to be slower on elaboration of emotions and, in particular, of disgust emotion. Considering that the participants were not impaired in cognition, our data support the hypothesis that emotional impairments emerge independently from damage to cognitive functions.

This article deals primarily with the problem of determining the cutting force when machining hardened steels. Secondary issues are focused on the evaluation of surface quality on machined samples and the recommendation of cutting conditions. A wide variety of components are used in engineering, the final heat treatment of which is hardening. These components are usually critical in a particular product. The quality of these components determines the correct functioning of the entire technical equipment and ultimately its service life. In our case, these are the core parts of thrust bearings, specifically the rolling elements. The subject of the experiment is machining these components in the hardened state with cubic boron nitride tools and continuous measurement of the cutting force using a dynamometer. The following evaluation assesses the surface quality by both touch and non-touch methods. A structural equation with appropriate constant and exponents was then constructed from the data obtained using the dynamometer.

Introduction: Body size is correlated with many aspects of an animal species' natural history, such as life span, abundance, dispersal capacity and diet breadth. However, contrasting trends have been reported for the relationship between body size and these ecological traits. Methods: Butterfly species from fruit-feeding guilds were used to investigate whether body size correlates with species abundances, dispersal, permanence, and diet breadth in a Neotropical savanna in Brazil (Cerrado). We used Blomberg’s K and Phylogenetic Generalized Least Squares models (PGLS) to measure phylogenetic signal strength in species traits, and to estimate size-dispersal-diet breadth associations while taking shared ancestry into account. Results: 539 individuals from 27 species were captured, and 190 individuals were recaptured, representing a 35% recapture rate. We found that body size negatively influenced butterfly abundance. In contrast, body size was positively associated with dispersal levels, distance traveled, number of traps visited, individual permanence, and diet breadth. These results indicate that larger butterflies have a greater proportion of dispersing individuals over longer distances, as they permanence were detected over longer periods than their smaller relatives. Moreover, larger butterflies are more generalized, based on the number of host plant families and genera they consume. Smaller butterflies demand fewer resources, which is reflected in their higher survival in small patches, and may explain their lower dispersal ability, and higher diet specialization. Nevertheless, lower dispersal ability, if not compensated by large population sizes, may threaten small-bodied species inhabiting environments with intense deforestation rates, such as the Cerrado. Conclusions: Body size positively influences dispersal and diet breadth in the fruit-feeding butterflies collected in this study.

Virtual human body models contribute to designing safe and user-friendly products through virtual prototyping. Anthropometric biomechanical models address different physiques using average dimensions. In designing personal protective equipment, biomechanical models with the correct geometry and shape shall play a role. The presented study shows the variations of subject-specific anthropometric dimensions from the average for the different population groups in the Czech Republic and China as a background for the need for personalized human body models. The study measures a set of clothing industry dimensions of Czech children, Czech teens, Czech adults and Chinese adults and compares them to the corresponding age average, which is represented by a scaled anthropometric human body model. The cumulative variation of clothing industry dimensions increases the farer is the population group from the average. It is smallest for the Czech adults 7.54% ± 6.63%, Czech teens report 7.93% ± 6.25% and Czech children differ 9.52% ± 6.08%. Chinese adults report 10.86% ± 11.11%. As the variations of the particular clothing industry dimensions from the average prove the necessity of having personalized subject-specific models, the personalization of particular body segments using the measured clothing industry dimensions leading to a subject-specific virtual model is addressed. The developed personalization algorithm results in the continuous body surface desired for contact applications for assessing body behavior and injury risk under impact loading.

Reconstructing ancestral species is a challenging endeavour: fossils are often scarce or enigmatic, and inferring ancestral characters based on novel molecular approaches (e.g. comparative genomics or developmental genetics) has long been controversial. A key philosophical challenge pertinent at present is the lack of a theoretical framework capable of evaluating inferences of homology made through integration of multiple kinds of evidence (e.g. molecular, developmental, or morphological). Here, I present just such a framework. I start with a brief history and critical assessment of attempts at inferring morphological homology through developmental genetics. I then bring attention to a recent model of homology, namely Character Identity Mechanisms (DiFrisco, Love, & Wagner, 2020), intended partly to elucidate the relationships between morphological characters, developmental genetics, and homology. I utilise and build on this model to construct the evaluative framework mentioned above, which judges the epistemic value of evidence of each kind in each particular case based on three proposed criteria: effectiveness, admissibility, and informativity, as well as providing a generalised guideline on how it can be scientifically operationalised. I then point out the evolution of the eumetazoan body plan as a case in point where the application of this framework can yield satisfactory results, both empirically and conceptually. I will conclude with a discussion on some potential implications for more general philosophy of biology and philosophy of science, especially surrounding evidential integration, models and explanation, and reductionism.

Throughout the eukaryotic tree of life, amoeboid organisms have evolved that aggregate upon starvation and form multicellular fruiting bodies, consisting of a ball of spores atop a stalk. This chapter discusses the remarkable convergent evolution of a stalked fruiting body in these different taxa. It then discusses a well-studied group of aggregative fruiters, the cellular slime molds, in more detail. These organisms exhibit substantial variation in their stalk formation and composition, which allows a better understanding of the evolution, maintenance and possible functions of stalked fruiting bodies, but also points to potential costs and benefits of different types of stalks.

The Body Mass Index (BMI) formula has been developed by Belgian mathematician Adolphe Quetelet and published in 1840 [1] as a law of nature and society, based on statistics about the weight and height of the population of that time, the first part of the 19^th century. He called it “social physics”. From then, for nearly two centuries, the BMI had been the most important formula describing the normal relations and ratio of weight to the square of the height for humans. The problem arises if the BMI formula, developed in the first part of the 19^th century is still good today when the type of work people perform is very different? In modern times, most people are less muscular than at the time when the BMI was developed because they do not work physically as heavy as at that time. In many cases, the Body Mass index can predict mortality, morbidity and illness but not always, for example cases such as (a) the obesity paradox for some cardiovascular problems and (b) the U shape mortality paradox as well as (c) false positive obesity diagnostic in regard to people who are strong and muscular, have low body fat percentage but are classified as obese by the BMI and (d) cases where BMI is normal but people have an “obese metabolism” (e) BMI normal but high fat percentage. The objective is to develop a formula good for all body types, a formula that makes the difference between fat and non-fat body weight such as muscle and body frame and quantifies the effect of strength and fitness, which BMI does not. Another objective is to develop a formula to predict the health risks and fitness status of people, better than BMI. The first generalizations of BMI using anthropometric metrics could be found in [2], where I discuss and analyze many formulae, developed, tested, and simulated by me, using similar new methods, accounting for body shape, physical shape and body function, making the difference between muscle mass and fat, fat and non fat body weight. Nearly all formulae and methods developed and proposed in this new model are new, never published before. Many experiments published before, in highly cited papers show that grip strength and muscle strength is a predictor of health, mortality, morbidity, endocrine and metabolic disease outside the BMI and anthropometric measures. The purpose of my formula is to explain the outcome of those experiments and create a formula which predicts these experiments [21-41].

The link between scoliotic deformity and bone metabolism in adolescent idiopathic scoliosis (AIS) has not been well researched. Moreover, the data concerning the cross-talk between fat tissue content/hormonal activity and bone markers in this group of patients are lacking. The objective of this study was to correlate the extent of scoliotic-curve severity with the bone turnover vs. leptin level and nutritional status in girls with AIS. The study encompassed 77 AIS girls, aged 14.7 ± 2.17 years. Scoliotic curve severity assessed by Cobb’s angle was categorized as mild (10-19o) moderate (20-39º) or severe (≥40º). Corrected height, weight, waist and hip circumferences were measured and body mass index (BMI), corrected height Z-score, BMI Z-score and waist/height ratio (WHtR) were calculated for the entire group. Body composition parameters: fat mass (FAT), fat-free mass (FFM) and predicted muscle mass (PMM) were determined using a bioelectrical impedance analyzer. Bone turnover markers (osteocalcin (OC) and amino terminal of collagen cross-links NTx) and leptin levels were assessed in serum. Multiple regression analysis showed that, OC, NTx (negatively with p<0.05) and leptin (positively with p<0.01) were significantly associated with curve severity in AIS girls. Moreover, Cobb’s angle was positively correlated with W/HtR (p<0.01)and FAT (p<0.05). One-way analysis of variance (ANOVA) revealed significant differences in leptin (p<0.05 vs. mild only), OC (p<0.05 vs. mild and moderate)) and W/HtR (p<0.01 and p<0.05 vs. mild and moderate respectively) between the three AIS severity subgroups. OC was significantly lower in the severe AIS subgroup, while leptin and W/HtR were significantly higher. Significant correlations between leptin and anthropometrical parameters as BMI z-score and W/HtR were shown. Leptin level correlated also significantly with BMI z score (p<0.001), W/HtR (p<0.0001) and body composition parameters (p<0.000001). Moreover, there was a significant negative correlation between NTx and leptin level (p<0.05). Bone metabolism in AIS girls seems to be altered and significantly related to the scoliotic curve severity. Leptin may be a crucial link in the cross-talk between bone turnover and body composition in this group of patients. Further studies concerning this topic are needed.

Background and objectives: Patients with multiple sclerosis (MS) have many potential factors (spasticity, immobilization, glucocorticoids use) which can deteriorate the anthropometrical status and body composition and may have the potential impact on the functional mobility and basic motor skills improvement after physiotherapy. The aim of the study was to assess the functional mobility and basic motor skills in patients with MS and to correlate them with disability and anthropometrical status and body composition parameters. Materials and Methods: Timed Up-and-Go test (TUG), and six-minute walk test (6MWT) were performed in 36 patients with MS before and after 4 weeks of physiotherapy. Body mass index (BMI), waist to height ratio (W/HtR), and waist-to-hip ratio (WHR) were assessed in this group. Body composition was evaluated by bioelectrical impedance analysis (BIA) and fat mass (FAT), fat free mass (FFM), total body water (TBW) and predicted muscle mass (PMM) were expressed as percentage of body mass. Clinical status was assessed by EDSS and AI scales. Results: After physiotherapy, there was a significant improvement in functional mobility and basic motor skills assessed by total distance in 6MWT (p<0.001) and in TUG trials (p<0.001). Positive significant correlations were found between the results obtained in both tests (either before and after physiotherapy) vs. FFM, TBW and PMM, whilst worse results in functional mobility and basic motor skills correlated significantly with higher WHtR, WHR and FAT (p<0.05). Clinical status (EDSS) were significantly related to the WHtR and body composition parameters with the same manner as the results in the either 6MWT and TUG. However, there were no significant relationships between BMI vs. either clinical status (EDSS, AI) and functional mobility tests results in patients with MS. Conclusions: Functional mobility and basic motor skills may be significantly improved during the physiotherapy, but they are related to the anthropometrical status and body composition of MS patients. Moreover, disability status is also significantly related to this parameters. Body composition deterioration seems to be the important target for the therapeutic intervention in MS patients. For proper nutritional status assessment in patients with MS, body composition analysis or WHtR instead BMI should to be used.

Recent studies on the image of the Turin Shroud (TS) lead to think it could have been formed through a not well-identified mechanism of energy radiation. In order to remove some lacunas about this imaging process, a reverse engineering method has been applied to it, arriving to exclude some possible mechanisms. The image formation of a human face wrapped on a cloth by using an ad-hoc developed software has been simulated. The results of different kinds of the radiation depending from different parameters have been simulated, each one connected with accredited hypotheses. On the basis of the comparison among the different images produced by the software and the TS Face, some useful information both about the kind of radiation and the cloth wrapping conditions have been obtained. The effect of image distortion of a cloth wrapped around a face has been discussed too by defining the best laws of radiation and of their attenuation with distance. A Lambertian law is not compatible with the TS image. A vertical radiation shows a problem in reproducing the requested resolution. A radiation perpendicular to the emitting surface, like that produced by an electric field appears promising to explain the TS Face.

The present study investigated the association of accelerometer-determined moderate-to-vigorous physical activity (MVPA) with neck circumference (NC) in adolescents and adults from eight Latin American countries. The sample consisted of 2370 participants from the Latin American Study of Nutrition and Health, a multicenter cross-sectional nutrition and health surveillance study of a nationally representative sample from eight Latin American countries. An Actigraph GT3X+ accelerometer was used to monitor MVPA. Adolescents were categorized as NC > 34.25 cm in boys and NC > 31.25 cm in girls, and adults were categorized as NC > 39 cm in men and NC > 35 cm in women. The average time of MVPA was 34.88 min/day, ranging from 31.16 in Venezuela to 40.27 in Chile. Concerning NC, 37.0% of the sample was classified as having elevated NC. Chile was the country with the highest percentage of people with elevated NC (56.9%), and Colombia had the lowest percentage (24.8%). Overall, the MVPA (min/day) was associated with elevated NC (OR = 0.994, CI95% = 0.990–0.998). In Costa Rica and Peru, there were significant associations between MVPA and NC when analyzed by country. Further research is required to understand the differences between countries in the observed associations.

Inadequate protein intake can impair protein balance and lead to skeletal muscle atrophy, impaired body growth, and functional decline. Foods provide both non-essential (NEAAs) and essential amino acids (EAAs) that may convey different metabolic stimuli to specific organs and tissues. In this study, we sought to evaluate the impact of six diets with various EAA/NEAA blends on body composition and the risk of developing tissue wasting in late middle-aged male mice. Mice consuming NEAA-based diets, although showing increased food and calorie intake, suffered the most severe weight loss. Interestingly, even moderate NEAAs prevalence was able to induce inflammatory catabolic stimuli, generalized body wasting and systemic metabolic alterations. Complete depletion of retroperitoneal white adipose tissue and a severe loss (>75%) of brown adipose tissue were observed together with muscle wasting. Conversely, EAA-based diets induced significant decreases in weight by reducing primarily fat reserves, but improved clinical parameters. Tissue wasting was caused by altered AA quality, independent of reduced nitrogen or caloric intake. Our results indicate that an optimized balance of AA composition is necessary for preserving overall bodily energy status. These findings are particularly relevant in the context of aging and may be exploited for contrasting its negative correlates including body wasting.

We explore the possibility of using the external regions of galaxy clusters to measure their mass accretion rate (MAR). The main goal is to provide a method to observationally investigate the growth of structures on the nonlinear scales of galaxy clusters. We derive the MAR by using the mass profile beyond the splashback radius, evaluating the mass of a spherical shell and the time it takes to fall in. The infall velocity of the shell is extracted from N-body simulations. The average MAR returned by our prescription in the redshift range z=[0, 2] is within 20-40% of the average MAR derived from the merger trees of dark matter haloes in the reference N-body simulations. Our result suggests that the external regions of galaxy clusters can be used to measure the mean MAR of a sample of clusters.

The demands for high power and low emissions put focus on energy efficiency when developing new engines. An important part is the UAV engine cooling system, which cools the engine structure below damaging temperatures. For high temperatures in the cooling system there is a risk that boiling occurs and while the initial nucleate boiling enhances the cooling effect, the subsequent Film boiling decreases the heat transfer drastically. It is important to understand the benefits and limitations of various fluids when designing a two-phase cooling system. This paper proposes an alternative organic coolant. Its normal application range is 15°C to 400°C, and its pressure range is from atmospheric to 10.6 bar. DOWTHERM A fluid possesses unsurpassed thermal stability at temperatures of 400°C. This fluid, in both the liquid and vapor form, is noncorrosive toward common metals and alloys. Even at the high temperatures involved, the equipment usually exhibits excellent service life. Original equipment in many systems is still being used after 30 years of continuous service. The numerical results, described in this paper, show the potential of DOWTHERM A as a good alternative for cooling a UAV engine. It will extend the working temperature range of the Diesel engine and will maintain the structural integrity of the piston, cylinder and the piston rings.

We know that the classical Mittag-Leffler function play an important role as solution of fractional order differential and integral equations. We introduce the j-generalized p - k Mittag-Leffler function. We evaluate the second order differential recurrence relation and four different integral representations and introduce a homogeneous linear differential equation whose one of the solution is the j-generalized p-k Mittag-Leffler function. Also we evaluate the certain relations that exist between j-generalized p - k Mittag-Leffler function and Riemann-Liouville fractional integrals and derivatives. We evaluate Mellin-Barnes integral representation of j-generalized p-k Mittag-Le er Function. The relationship of j-generalized p-k Mittag-Leffler Function with Fox H-Function and Wright hypergeometric function is also establish. we obtained its Euler transform, Laplace Transform and Mellin transform. Finally we derive some particular cases.

Morphological and phylogenetic (45S nrDNA+RPB1 gene) analyses of three glomoid spore-producing arbuscular mycorrhizal fungi revealed the presence of two new species be-longing to the genus Glomus in the family Glomeraceae. In the field, Glomus highlandensis sp. nov. was found in a saltmarsh of the Scottish Highlands and in maritime sand dunes of the Baltic Sea in Poland, both saline environments, while G. mongioie sp. nov. originates from the Italian Alps. Phylogenetic placement analysis using environmental sequences indicated that G. highlandensis could have likely worldwide distribution while G. mongioie seems to be a rare species in the world. The molecular and phylogenetic analysis provided important insights about the presence of ribosomal variants in Glomus, with potential negative implication in phylogeny and species recognition.

Permafrost covers about 23% ~ 25% of the land in the northern hemisphere, mainly in Russia, Canada, Alaska, Northeast and Qinghai Tibet Plateau (QTP) in China. Many engineering especially the transportation has been in the permafrost regions above. Under the action of highways construction and global warming, permafrost under infrastructures is degraded and causes serious damage. Two phases closed thermosyphon (TPCT) is a widely accepted green countermeasure against the problem in permafrost regions. Although it has been applied to prevent permafrost degradation, their application presents significant challenges on account of the stronger endothermic action of asphalt pavement. This paper focused on the thermosyphon technology and application in the permafrost. Moreover, the article highlighted the excellent working performance of the TPCT that improving the stability of the infrastructures and prevent it degrading due its excellent efficiency of heat transfer. The industrial applications of the TPCT were also summarized, along with their limitations. Finally, the results reported in this paper can provide a valuable guidance for the design of the TPCT and construction of the permafrost regions in the future.

This study explored the feasibility of fluoride removal from simulated semiconductor industry wastewater and its recovery as calcium fluoride using fluidized bed crystallization. The continuous reactor showed best performance (>90% fluoride removal and >95% crystallization efficiency) at a calcium to fluoride ratio of 0.6 within first 40 days of continuous operation. The resulting particle size increased by more than double during this time along with a 36% increase in the seed bed height indicating deposition of CaF2 onto the silica seed. The SEM-EDX analysis showed the size and shape of the crystals formed along with high amount of Ca-F ions presence. The purity of the CaF2 crystals were determined to be 91.1% though ICP-OES analysis. Following the continuous experiment, different process improvement strategies are explored. The addition of excess amount of calcium resulted in an additional 6% fluoride removal, however, compared to this single stage process, a two-stage approach was found to be better strategy to achieve a low effluent fluoride concentration. The fluoride removal reached 94% with this two-stage approach under optimum condition of 4 + 1 h HRT combinations and a [Ca2+]/[F-] ratio of 0.55 and 0.7 for the two reactors, respectively. CFD simulation showed the impact of inlet diameter, bottom-angle shape and width and height ratio of the reactor on mixing inside reactor and possibility of further improvement in reactor performance by optimizing the FBR configuration.

Use of probiotic lactobacilli has been proposed as a strategy to mitigate damage associated to exposure to toxic metals. Their protective effect against cationic metal ions, such as those of mercury or lead, is believed to stem from their chelating and accumulating potential. However, their retention of anionic toxic metalloids, such as inorganic arsenic, is generally lower. Through the construction of mutants in phosphate transporter genes (pst) in Lactiplantibacillus plantarum and Lacticaseibacillus paracasei strains, coupled with arsenate [As(V)] uptake and toxicity assays, we determined that the incorporation of As(V), which structurally resembles phosphate, is likely facilitated by phosphate transporters. Surprisingly, inactivation in Lc. paracasei of PhoP, the tran-scriptional regulator of the two-component system PhoPR, a signal transducer involved in phosphate sensing, led to an increased resistance to arsenite [As(III)]. In comparison to the wild type, the phoP strain exhibited no differences in the ability to retain As(III), and there were no observed changes in the oxidation of As(III) to the less toxic As(V). These results reinforce the idea that specific transport, and not unspecific cell retention plays a role in As(V) biosorption by lactobacilli, while they reveal an unexpected phenotype for the lack of the pleiotropic regulator PhoP.

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations of heat transfer coefficient and pressure drop for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation and the error is quantified. It is the intention of the authors that this could be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for not usual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers (N = 53) deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated.

Accurate estimation of Remaining Useful Life (RUL) for aircraft engines is essential for ensuring safety and uninterrupted operations in the aviation industry. Numerous investigations have leveraged the success of attention-based Transformer architecture in sequence modeling tasks, particularly in its application to RUL prediction. These studies primarily focus on utilizing onboard sensor readings as input predictors. While various Transformer-based approaches have demonstrated improvement in RUL predictions, their exclusive focus on temporal attention within multivariate time series sensor readings, without considering sensor-wise attention, raises concerns about potential inaccuracies in RUL predictions. To address this concern, our paper proposes a novel solution in the form of a two-stage attention based hierarchical transformer (STAR) frame-work. This approach incorporates a two-stage attention mechanism, systematically addressing both temporal and sensor-wise attentions. Furthermore, we enhance the STAR RUL prediction framework by integrate hierarchical encoder-decoder structures to capture valuable information across different time scales. By conducting extensive numerical experiments with the CMAPSS datasets, we demonstrate that our proposed STAR framework significantly outperforms current state-of-the-art models for RUL prediction.

The two-scale method (TSM) is an effective approach to simulate electromagnetic (EM) scattering from rough sea surface, to interpret physical interaction of EM wave with rough sea surfaces. The sea surface roughness spectrum and the cutoff wavenumber are two key factors affecting the accuracy of TSM simulation. This paper takes the geophysical model functions (GMFs) of different band as reference, and quantitatively studies the two factors based on the numerical simulation of different polarization backscattering coefficients. The numerical simulation demonstrates that Apel spectrum is more suitable for the backscattering simulation in C/X/Ku-band, and the optimal cutoff wavenumbers are also derived for TSM simulation of EM scattering in C/X/Ku-band. Then an empirical model function of optimal cutoff wavenumbers with respect to frequency, incident angle and wind speed are obtained with regression method. Finally, the simulation results with the new model function of cutoff wavenumber are compared with the GMF and measured data in different bands and they are all consistent. Moreover, a physical explanation for the optimal cutoff wavenumber is also given.

We have investigated the canine of olive flounder in terms of the nonlinear optical signals of two-photon excitation autofluorescence (2PEF) and second harmonic generation (SHG), whereby two kinds of nonlinear microscope images of the canine were obtained using ~140 femtosecond pulses. For increasing excitation power of laser pulses, a photobleaching effect was found to be significant in the red and green ranges of autofluorescence, where a double-exponential decay of the intensity occurs within hundreds of second due to collagen fluorophores in the canine. In the blue range of autofluorescence, the photobleaching is suppressed due to an energy conversion of the incident laser pulse to SHG signal. As a result, the signal in blue range remains constant for long term exposure to laser. We have also found that the SHG intensity depends on the orienta-tion of linearly polarized excitation, and the optical anisotropy of SHG can be attributed to the collagen alignment of canines.

In this study, cotton fabric reinforced phenolic resin (CPF) composites were modified by adding four two-dimensional fillers: graphitic carbon nitride (g-C3N4), graphite (Gr), molybdenum disulfide (MoS2), and hexagonal boron nitride (h-BN). The tribological properties of these modified materials were investigated under dry friction and water lubrication conditions. CPF/ Gr composite exhibits significantly better tribological performance than the other three fillers modified CPF composites under dry friction, with a 24% reduction in friction coefficient and a 78% reduction in wear rate compared to unmodified CPF composite. Under water lubrication conditions, all four fillers did not significantly alter the friction coefficient of the CPF composite. However, except for an excessive amount of Gr, the other three fillers can reduce the wear rate. Particularly, in the case of 10% MoS2 content, the wear rate decreased by 56%. Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were employed for the analysis of the morphology and composition of the transfer films. Additionally, molecular dynamics (MD) simulations were conducted to investigate the adsorption effects of Gr, MoS2, and PF on the counterpart surface under both dry friction and water lubrication conditions. The difference in the adsorption capacity of Gr and MoS2 on the counterpart, as well as the resulting formation of transfer films, accounts for the variation in tribological behavior between CPF/Gr and CPF/MoS2 composites. By combining the lubrication properties of MoS2 and Gr under dry friction and water lubrication conditions, using them as co-fillers can achieve a synergistic lubrication effect.