A comparative analysis of the features of UV- stimulated emission (SE) of various types of disorder active materials based on ZnO crystallites for a random laser (RL) was carried out. The superlinear increase in the intensity of the UV photoluminescence (PL) band of polydisperse nano- microcrystalline (PNMC) ZnO powder at a wavelength of λ = 387 nm and some narrowing of its half-width in the range of 20-15 nm with increasing pump intensity indicate random lasing with incoherent feedback (FB). Properties of similar UV PL bands under the same conditions from a thin film containing hexagonal ZnO microdisks, as well as samples of monodisperse ZnO nanopowder indicate stimulated emission with coherent feedback. It is shown that, among the studied materials, the PNMC ZnO powder with crystallites contained nano-grains with is the most suitable for creating a laser with incoherent feedback at room temperature. The dominant factor of UV SE in PNMC ZnO powder is radiation transitions under exciton - exciton scattering conditions. The possible mechanisms of this random emission with the continuous spectrum are discussed. The average optical gain coefficient αg at λ = 387 nm in this RL system is estimated, as αg ~ 150 cm-1.

The DNS of film boiling requires strong computational resources that are difficult to obtain for a daily CFD use by the practitioners of the industrial R&D experts. On the other hand, the film boiling experiments are associated with the usage of the expensive and highly sophisticated apparatus, and the research to this end is found to be relatively difficult due to high heat flow rates that are present in the process itself. When combined with a transient heat conduction in a solid, the problem becomes significantly difficult. Therefore, a novel method in computation of conjugate heat transfer during film boiling in a quiescent liquid has been proposed in this paper. The method relies on the solution of mass, momentum and energy conservation equations in a two-fluid framework, supplemented with the appropriate closures. Furthermore, the turbulent flow has been found as an important parameter in obtaining the accurate solution of the temperature field evolution in a solid specimen, via the proper modeling of turbulent kinetic energy (TKE) value, that has been imposed as a constant value, i.e., the frozen turbulence approach. It was found, in addition, that the appropriate TKE value can be obtained by use of Kelvin-Helmholtz instability theory in conjunction with the boundary layer theory. The obtained results show excellent agreement with the experimental data within the first 15 s of the experiment, i.e., the first ca. 10 % of the total duration of the film boiling mode of heat transfer. Furthermore, the heat transfer coefficient has matched the error bands prescribed by the authors of the paper that has presented the correlations, whilst the averaged values are far beyond this band, i.e., are slightly more than 30 % higher. The further inspection has revealed a measure of similarity between the computational result of the volume fraction field distribution and the experiment, thus confirming the capability of the method to obtain realistic interface evolution in time. The method has shown full capability for further pursuing the industrial-scale film boiling problems that involve turbulent flow and the conjugate heat transfer approach.

Lead-based ternary chalcogenide thin films of the (PbTe)1-x(PbS)x system were obtained by plasma-enhanced chemical vapor deposition technique (PECVD) under conditions of a nonequilibrium low-temperature argon plasma of an RF discharge (40.68 MHz) at a reduced pressure (0.01 Torr). High-purity elements were directly used as starting materials – Pb, S and Te. Plasma-chemical synthesis was carried out on the surface of of c-sapphire and silicon substrate. The physicochemical properties of the films were studied by various analytical methods. The dependence of the Seebeck coefficient, resistivity, and power factor on the structural properties and composition has been studied. The thermoelectric characteristics were found to be dependent on the film composition. Upon the selection of optimal sulfur concentration one can increase the power factor as compared to single phase PbS ot PbTe films.

Abstract: To reduce the indiscriminate use of pesticides and extend the postharvest shelf life of peach fruit (cv. Baihua) from southeast China, microbial antagonism of indigenous yeasts was mainly studied and applied in construction of composite film. After isolation, purification, cultivation and identification, a total of 14 yeast strains from 9 genera were screened out from the surface of peaches. By experimental analysis of in vitro inhibition zone and in vivo colonizing capacity, Candida oleophila sp-ELPY12B and Cryptococcus laurentii sp-ELPY15A, which have conservative structure of D1/D2 domain sequences and were considered as new species by phylogenetic analysis, were finally chosen as fungicides against the major pathogens. In combination of Na-alginate film (0.4 % glycerin as plasticizer and 0.1 % Tween-80 as emulsifier), the preservative effects of composite-treated groups (1 × 108 CFU mL−1 of Candida oleophila sp-ELPY12B and Cryptococcus laurentii sp-ELPY15A) showed best antifungal effects, which significantly delayed the postharvest preservation period about 6 - 7 d under ambient temperature of 25 ± 3°C and relative humidity of 50 - 70%.

The aim of this work is to synthesis and characterize the Ta/TaN multilayer thin film coatings on 52100 tool steel under three different levels of N2 gas flow rate. The High Power Impulse Magnetron Sputtering (HiPIMS) technique was used for the deposition of Ta/TaN thin film multilayers on the substrate. Microstructure, coating thickness, composition, hardness and tribological properties of Ta/TaN multilayer coatings were characterized using scanning electron microscopy (SEM), Energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), microhardness tester and pin-on-disc tester, respectively. Adhesion property was evaluated via scratch testing of the thin film thin film layer. The lowest coefficient of friction was observed with the thin film layer of higher N2 gas flow rate due to the highest adhesion value of the coating on the surface. The obtained results on hardness, adhesion and coefficient of friction properties demonstrated that this Ta/TaN multilayer thin film coating can be used for tribological applications.

We present an integrable, sensor inlay for monitoring crack initiation and growth inside bondlines of structural carbon fiber reinforced plastic (CFRP) components. The sensing structures are sandwiched between crack stopping polyvinyliden fluoride (PVDF) and a thin reinforcing polyetherimide (PEI) layer. Good adhesion at all interfaces of the sensor system and to the CFRP material is crucial as weak bonds can counteract the desired crack stopping functionality. At the same time, the chosen reinforcing layer must withstand high strains, safely support the metallic measuring grids and possess outstanding fatigue strength. We show that this robust sensor system, which measures the strain at two successive fronts inside the bondline, allows to recognize cracks in the proximity of the inlay regardless of the mechanical loads. Feasibility is demonstrated by static load tests as well as cyclic long-term fatigue testing with up to 1,000,000 cycles. In addition to pure crack detection, crack distance estimation based on sensor signals is illustrated. The inlay integration process is developed with respect to industrial applicability. Thus, implementation of the proposed system will allow the potential of lightweight CFRP constructions to be better exploited by expanding the possibilities of structural adhesive bonding.

Biodegradable and renewable plastic films have been regarded as promising alternative green materials to achieve the substitution polythene (PE)films to reduce plastic pollution. Poly (butylene adipate-co-terephthalate) (PBAT) is a kind of biodegradable polyester, which is widely used in the production of biodegradable mulching films. However, the high cost of PBAT limited it applications. Thus, lignin, one of the most abundant biomass resources was incorporated into PBAT matrix in the present work. A series of Lignin/PBAT biodegradable plastics films with different Lignin/PBAT weight ratios (0.00 %-5.00 %) were successfully fabricated using twin screw and twin roll extruders. The chemical compositions, morphologies, thermal stabilities, mechanical properties, and barrier properties of samples were characterized by XRD, FTIR, TG/DSC, mechanical testing machine, and WVTR, respectively. Results show that the corporation of lignin into PBAT matrix could lead to improved thermal stabilities, mechanical properties and barrier properties of films even after Xenon lamp aging process, especially when Lignin/PBAT weight ratio is 1.00 % in the present work. This work provides a very promising approach for fabrication of biodegradable plastics films with low cost, enhanced mechanical properties and barrier properties, the as-prepared samples may have potential applications in agricultural or food packaging materials.

Marangoni flow in foam fractionation in the lamellar film for the interior and exterior of a micro-foam was investigated. The three-dimensional node-film-Plateau Border system was modeled using computational fluid dynamics. The importance of the surfactant concentration of the foam fractionation column and air-liquid interface mobility on the Marangoni velocity in the film was emphasized. The study found that an increase in surfactant concentration in the reflux column significantly increases the Marangoni velocities. Additionally, a mobile interface results in a higher Marangoni flow, while a rigid interface leads to less intensive flow. The behavior of the Marangoni flow in both interior and exterior foam was explored, revealing that the flow in exterior foam has different behavior due to the presence of the wall, which reduces the Marangoni velocity compared to interior films.

Porous ferroelectric lead zirconate-titanate (PZT) films are a promising material for various electronics applications. This study focuses on understanding how structure-directing agent (polyvinylpyrrolidone) can change structure and electrical properties of porous PZT films prepared by chemical solution deposition. The films with various porosity up to ~ 40 vol.% and pore connectivity changing from 3-0 to 3-3 were prepared and studied by capacitance-voltage, dielectric hysteresis, transient current, photocurrent, and local current techniques. We have found that the linear decrease in the material volume in a porous film is not the only factor governing film properties. The key role in changing electrical properties plays the creation of new internal grain boundaries. This research expands the understanding of physical phenomena in porous ferroelectric films and may enable the development of new materials and devices.

Film cooling technology is of great significance to enhance the performance of aero-engines and extend service life. With the increasing requirements for film cooling efficiency, researchers and engineers have carried out a lot of work on the precision and digital measurement of cooling holes. Based on the above, this paper outlines the importance and principles of film cooling technology, reviews the evolution of cooling holes. Also, this paper details the traditional measurement methods of the cooling hole used in current engineering scenarios with their limitations and categorizes digital measurement methods into five main types, including probing measurement technology, optical measurement technology, infrared imaging technology, computer tomography(CT) scanning technology, and composite measurement technology. The five types of methods and integrated automated measurement platforms are also analyzed. Finally, through a generalize and analysis of cooling hole measurement methods, this paper points out technical challenges and future trends, providing a reference and guidance for forward researches.

As one of the most critical parameters to evaluate the quality and performance of mobile phones, real-time temperature monitoring of the mobile phone integrated chips is vitally important in the electronics industry. Although several different strategies for chip surface temperature measurement have been proposed in recent years, distributed temperature monitoring with the high spatial resolution is still a hot issue to be solved urgently. In this work, a fluorescent film material with photothermal properties containing thermosensitive upconversion nanoparticles (UCNPs) and polydimethylsiloxane (PDMS) is fabricated for chip surface temperature monitor-ing. The presented fluorescent films have thicknesses ranging from 23 to 90 μm and are both flexible and elastic. Using the fluorescence intensity ratio (FIR) technique, the temperature sens-ing properties of these fluorescent films are investigated. The maximum sensitivity of the fluo-rescent film was measured to be 1.43% K-1 at 299 K. By testing the temperature at different posi-tions of the optical film, a distributed temperature monitoring with a high spatial resolution down to 10 μm on the chip surface is successfully achieved. It is worth mentioning that the film maintains stable performance even under pull stretch up to 100%. The correctness of the method is verified by taking infrared images of the chip surface with an infrared camera. These results demonstrate that the as-prepared optical film is a promising anti-deformation material for high spatial resolution temperature monitoring on-chip surfaces.

This paper presents the design of a miniaturized polyimide-based antenna for Ultra-Wideband (UWB) communication. Miniaturization is achieved through the utilization of adhesive material with a high dielectric constant (high-Dk). The goal of this work is to investigate the impact of such material on the antenna performance and to optimize its design for UWB operation. The manufacturing of the antenna using the proposed structure was developed and the prototype of antenna for UWB high-band (6 - 9 GHz) is measured and analyzed. By leveraging the high Dk of the adhesive material, the simulation and measurement results showed that the proposed antenna with high Dk adhesive film can achieve the compact dimension with good performance in gain, and time domain characteristics. The results of this study show a potential of exhibiting a reduction in the size of the antenna and will contribute to the advancement of miniaturized UWB antenna technology.

Bismuth sodium titanate thin films (BNT) were deposited on Pt/SiN substrates by Sol-Gel spin coating technique under O2 atmosphere. Microstructural, structural, and electrical properties of the obtained film were investigated. Scanning electron microscopy and atomic force microscopy micrographs were used to analyze the microstructure of the films. Furthermore, EDX analysis revealed a Na-deficient composition for the obtained film. X-ray diffraction and Raman spectroscopy allowed the identification of a pure perovskite BNT phase. Dielectric, ferroelectric, and leakage current measurements revealed good frequency stability of the dielectric constant and dielectric losses for BNT thin film. The results are discussed in terms of Na-deficiency effects on the defect structure of BNT. Further, the film showed attractive electrostatic energy storage properties with energy density that exceeds 1.04 J/cm3 under E = 630 kV/cm.

Iron, a crucial element in our environment, plays a vital role in numerous natural processes. Understanding the presence and concentration of iron in the environment is very important, as it impacts various aspects of our planet’s health. On-site detection and speciation of iron are significant for several reasons. In this context, the present work aims to evaluate the applicability of voltammetry for on-site determination of iron and its possible speciation using a portable voltammetric analyzer. Voltammetry offers the advantage of convenience and cost-effectiveness. For iron (III) determination a modification of a glassy carbon electrode (GCE) with an antimony-bismuth film (SbBiFE) using acetate buffer (pH=4) as supporting electrolyte was used. The technique adopted was Square Wave Adsoptive Cathodic Stripping Voltammetry (SW-AdCSV) and we used 1-(2-piridylazo)-2-naphthol (PAN) as iron (III) ligand. Linearity, repeatability, detection limit and accuracy were determined using synthetic solutions, then a Standard Reference Material (SRM) 1643f - Trace Elements in Water was used for validation measurements in real matrix. The procedure was finally applied to real samples (tap, lake and sea water) and the results obtained were compared by Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). The results obtained demonstrated the excellent applicability of the proposed on-site voltammetric procedure for the determination of iron and its speciation in water.

Giant unilamellar vesicles (GUVs) are membrane model used to study membrane properties. Electroformation is one of the methods used to produce GUVs. During electroformation protocol dry lipid film is formed. Drying of the lipid film induce Cholesterol (Chol) demixing artifact, in which Chol forms anhydrous crystals, where these crystals does not participate in formation of vesicles. This leads to a lower Chol concentration in the vesicle bilayers compared to the Chol concentration in the initial lipid solution. To address this problem, we propose novel electroformation protocol that includes rapid solvent exchange, plasma cleaning and spin-coating methods to produce GUVs. We tested the protocol focusing on vesicles with high Chol content using different spin-coating durations and vesicle types deposition. Additionally, we compared the novel protocol using completely dry lipid film. The optimal spin-coating duration for vesicles made out of phosphatidylcholine/Chol mixture was 30 s. Mulitlamellar vesicles (MLVs), large unilamellar vesicles (LUVs) obtained by extrusion of MLVs through 100 nm membrane pores and LUVs obtained by extrusion of previously obtained LUVs through 50 nm membrane pores were deposited on electrode for 1.5/1 Chol/phosphatidylcholine lipid mixture and the results were compared. Electroformation using all three deposited vesicle types gave a high GUVs yield, but deposition of LUVs obtained by extrusion of MLVs through 100 nm membrane pores gave the most reproducible results. Using deposition of these LUVs, we produced GUVs with high yield for 6 different Chol concentrations (from 0 % to 71.4%). Using protocol that includes dry lipid film GUVs yield was lower and Chol demixing artifact was induced, proving that the lipid film should never undergo drying when Chol content is high.

In the present work we have investigated an organic semiconductor based on tris(8-hydroxyquinoline) aluminum (AlQ3) doped with tetracyanoquinodimethane (TCNQ), which can be used as a photoactive layer in organic light-emitting device (OLED). DFT calculations were carried out to optimize the structure of semiconductor species and get related constants in order to compare experimental and theoretical results. The semiconductor AlQ3-TCNQ was structurally characterized and their experimental IR spectrum was compared with that obtained through DFT calculations. Subsequently, AlQ3-TCNQ films with polypyrrole (PPy) matrix were fabricated, they were morphologically and mechanically characterized by Scanning Electron and Atomic Force Microscopy techniques. The maximum stress for the film is 8.66 MPa and the Knoop hardness is 0.0311. The film was analyzed in its optical behavior and the optical properties of hybrid film were found to exhibit two indirect allowed transitions at 2.64 and 3.44 eV. Finally, an OLED type was fabricated that was electrically characterized. Applying a cubic-spline approximation to fit cubic polynomials to the J-V curves, the ohmic to SCLC transition voltage VON and the trap-filled-limit voltage VTFL for the device were obtained. Then, the free carrier density and trap density for the device were approximated to n0=2.4787×10171m3 and Nt=1.7419×10291m3 respectively.

This experimental study investigates the effect of scarf geometry in restoring the impact response of scarf patched 3 mm thick glass-fibre reinforced polymer (GFRP) matrix composite laminates. Traditional circular along with rounded rectangular scarf patch configurations considered as repair patches. Experimental measurements revealed that the temporal variations of force and energy response of the pristine specimen are close to that of circular repaired specimens. The predominant failure modes were witnessed only in repair patch which include the matrix cracking, fibre fracture, delamination and no discontinuity in adhesive interface was witnessed. When compared with the pristine samples, the top ply damage size of the of the circular repaired specimens is larger by 9.91 %, while that of the rounded rectangular repaired specimens is larger by 434.23 %. The results show that circular scarf repair is more suitable choice of repair approach under the condition of 37J low-velocity impact event even though the global force-time response is similar.

A flexible structure is applied to improve the lubrication performance of a misaligned journal bearing. The journal bearing is representative sliding bearing and there are damages due to metal-to-metal contact by misalignment. Since misalignment is an unavoidable phenomenon, a journal bearing with a flexible structure was proposed as a way to improve it. The lubrication characteristics of the bearing are evaluated numerically under steady-state condition. EHL (elastohydrodynamic lubrication) analysis considering elastic deformation was performed. The lubrication performance is compared in accordance with variation of the geometry of the flexible structure and evaluated based on the minimum film thickness. Moreover, the results of the journal bearing with flexible structure are compared with those of the journal bearing without the flexible structure. The flexible structure is then applied in the form of a groove to the area supporting high load on the journal bearing; it is elastically deformed by the generated oil-film pressure, which helps to obscure a larger oil film. Through numerical analysis, it is found that the journal bearing with flexible structure can improve the lubrication performance in the misaligned condition.

This research presents a novel approach to film analysis, leveraging word vectors to objectively evaluate movie critiques. Focusing on Director Chanwook Park’s award-winning film, ’Decision to Leave’, the study employs word vectors derived from the movie’s script of Korean text. Traditional critiques often emphasize contrasting elements and themes, but their subjective nature poses challenges in objective validation. To address this, we trained a language model using LSTM on the film’s script, obtaining word vectors that capture the essence of the narrative. These vectors were then used to perform various text analyses, including similarity and analogy operation for the keywords suggested by the critiques. By comparing the semantic relationships in the critiques with those derived from the word vectors, we could objectively validate the critiques’ assertions. Furthermore, we visualized the word vectors in a two-dimensional space, confirming the spatial relationships of key terms highlighted in critiques. The study underscores the potential of word vectors in providing a more objective lens for film analysis, bridging the gap between traditional film criticism and data-driven insights.

During shearer operation, piston rod is susceptible to wear from invasion of pollutants, and then ruins sealing ring in hydraulic cylinder. This work attempts to conduct a systematical investigation of Cu-DLC (Cu-doped Diamond-like Carbon) film to improve the seal performance. Failure process of hydraulic cylinder was analyzed, and relevant parameters were determined. Several Cu-DLC films were deposited on the substrate of piston rod in a multi-ion beam assisted system, and their structures and combined tribological performances were investigated. As a result, dust particles attached to the piston rod may enter the cylinder, and damage the sealing ring under the radial force. Cu grains prefer to orientate (111) crystal plane with increase of Cu content, and may induce drop of hardness and internal stress for the film. Friction coefficient of the film ranges from 0.04 to 0.15, and rise of IG/ID ratio from 1.4 to 2.3 in Raman data indicates that bond transition from sp3-C to sp2-C may lower the friction coefficient. Modification mechanism of Cu-DLC film for the seal performance may come from synergistic effects of (i) contact force and friction heat induce the film graphitization, (ii) Cu doping improves toughness of the film and acts as a solid lubricant, and (iii) transfer layer plays a role of self-lubrication.

A tumbler screen type residual film–impurity mixture wind separator as a key equipment for secondary utilization of farmland residual film. During the working process, the proportion of impurities in the separated waste mulch film intermittently increases, resulting in poor working stability of the device, which may hamper long-term operation. In this study, the material inside the separation unit was continuously monitored, and the main factor affecting separator per-formance was determined to be the challenges in the effective depolymerization of some residual film–impurity mixtures. The principles of agglomeration and depolymerization of the residual film–impurity mixtures were analyzed using computational fluid dynamics (CFD) and discrete element method (DEM) flow-solid coupling simulation methods. The key factor affecting the disaggregation of the mixture was the collision force between the residual film–impurity mixture and the trommel screen. The collision force was maximum when the residual film–impurity mixture first collided with the trommel screen when it was fed into the separation device. As determined by force analyses, the key factors affecting the collision force of the process were the material feeding amount and the structure of the inlet. Furthermore, simulations were carried out for different inlet structure forms; the evaluation index was the maximum collision force of the residual film–impurity mixture agglomerate on the trommel screen. The best disaggregation effect was obtained with a square feed inlet and at a feeding rate of 202 kg/h. A prototype was built using these specifications for verification. The average value of the ratio of impurities in the re-sidual film was 6.966%, the coefficient of variation was 7.38%, and the dispersion of statistical results was small. The ratio of impurities in the residual film was kept constant during the con-tinuous operation of the wind separator. Thus, this study analyzed the agglomerate disaggregation process and provided theoretical insights for deter-mining the optimal structures of the inlets of various cleaning devices and the feeding volumes.

In this study the formation of thin-film barrier coatings based on a highly-conducting Bi1.60Er0.4O3 (EDB) solid electrolyte on supporting Ce0.8Sm0.2O1.9 (SDC) electrolyte substrates is implemented for the first time using electrophoretic deposition (EPD). Electrokinetic properties of EDB-based suspensions in a non-aqueous dispersion medium of isopropanol modified with small additions of polyethyleneimine (PEI, 0.26 g/L) and acetylacetone (0.15 g/L), as well as in a mixed isopropanol/acetylacetone (70/30 vol.%) medium are studied. The dependences of the thickness of EDB coatings on voltage and deposition time are obtained using deposition on a model Ni-foil electrode. Preliminary synthesis of a conductive polypyrrole (PPy) polymer film is used to create surface conductivity of non-conductive SDC substrates. The efficiency of using a modified dispersion medium based on isopropanol to obtain a continuous EDB coating 12 μm thick, sintered at a temperature of 850 °C for 5 h, is shown. The microstructure and morphology of the surface of the EDB coating are studied. Pt/SDC/EDB/Pt cell is used to characterize the coating conductivity. The EPD method is shown to be promising for the formation of barrier coatings based on doped bismuth oxide. The developed method can be used for creating cathode barrier layers in SOFC technology.

The various methods used to choose the profile shift coefficients, primarily the so-called equalizations, were based on assumed advantages without physical evidence proving them. In this paper a new calculation method is presented for determining profile shift coefficient. The procedure gives the pair of values ​​of the profile shift coefficients, in which case, under the given load, the resulting bending stress will be of the lowest possible value.

The corrosion resistance of two cast CoCr based alloys, with different amounts of chromium and with different alloying elements in the bulk composition of the alloy, was assessed. Herewith, we investigated the corrosion behavior of Co21Cr8Mo7W and Co29Cr7W by open circuit potential (OCP), potentiodynamic polarization (PP) and electrochemical impedance spectroscopy (EIS) in 0.1 M phosphate buffer solution (PBS) at 37°C for long time immersion. After 1000 hours of immersion, the corrosion current density (icor), estimated from anodic polarization tests, is lower for Co21Cr8Mo7W (i.e. 49 nA cm-2) alloy compared to Co29Cr7W alloy (180 nA cm-2). As regards the corrosion potential (Ecor), a nobler value was observed for Co21Cr8Mo7W (i.e. -59 mV vs. Ag/AgCl) compared to Co29Cr7W (i.e. -114 mV vs. Ag/AgCl). These findings suggest a better corrosion resistance of the film formed on the alloy containing lower amount of Cr and two alloying elements, namely Mo and W. These results are promising ones in terms of medical applications because they open new strategies in obtaining alloys with lower content of chromium and with higher protective properties against corrosion attack.

Herein, bamboo-laminated lumber for furniture was coated with waterborne acrylic paint. The effects of different painting techniques and quantities on the drying rate, smoothness, hardness, adhesion and wear resistance of the paint film were investigated. Then, the thermal properties of the paint were analysed using thermogravimetry and differential scanning calorimeter to examine the film-forming mechanism. The results showed that painting technique had no effect on the drying time, flatness, hardness and adhesion of the paint film, but it influenced the wear resistance. Herein, the films’ flatness showed little variation with different painting methods (one-layer primer one-layer topcoat, one-layer primer two-layer topcoat, two-layer primer one-layer topcoat and two-layer primer two-layer topcoat). The drying time for primer surfaces/solids was 8min/8.5 min, while it was 6.5/7 min for topcoats. The paint films exhibited grade B hardness and grade 0 adhesion and the better wear resistance when using one-layer primer one-layer topcoat at 51.24 mg·100 r−1. The amount of paint applied significantly affected the drying time and flatness of the paint film. As the quantity increased, the drying time of the paint’s surfaces and solids also increased, whereas the film’s flatness initially increased before decreasing. The film’s optimal adhesion, hardness and wear resistance values were grade 0, grade B and 51.24 mg·100 r−1, respectively, when 80 g/m2 of paint was applied. Thermal analysis of the primer and topcoat showed that water decomposition occurred at 100℃ and thermal decomposition of organic components occurred at 350℃. The primer and topcoat exhibited the same weight loss, but primer’s thermal loss rate was higher than that of topcoat. Consequently, the topcoat displayed better thermal stability than the primer.

In this study we assessed the electrical and optical behavior of semiconductor hybrid films fabricate from octaethyl-21H,23H-porphine copper (CuP), embedded in polymethylmethacrylate (PMMA), and polystyrene (PS). The hybrid films were characterized structurally and morphologically by means of Infrared spectroscopy (IR), atomic force microscopy (AFM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). Subsequently, the PMMA:CuP and PS:CuP hybrid films were evaluated optically by UV-vis spectroscopy, as well as electrically, with the four-point collinear method. Hybrid films present a homogeneous and low roughness morphology, besides; the PS matrix allows the crystallization of the porphin, while the PMMA promotes the amorphous structure in CuP. The polymeric matrix also has an effect on the optical behavior of the films, since the smallest optical gap (2.16 eV) and onset gap (1.89 eV) and the highest transparency are obtained in the film with a PMMA matrix. Finally, the electrical behavior in hybrid films is also affected by the matrix: the largest amount of current carried is around 0.01 A for PS:CuP film, while for PMMA:CuP film it is 0.0015 A. Thanks to the above properties, hybrid films are promising candidates for use in optoelectronic devices.

Tantalum oxide thin films are deposited by DC reactive magnetron sputtering from a tantalum metallic target and oxygen as reactive gas. The reactive gas pulsing process (RGPP) is implemented to produce TaOx compounds with tunable chemical compositions. The argon mass flow rate is maintained constant whereas that of the oxygen gas is pulsed during the deposition. A constant pulsing period T = 10 s is used and the introduction time of the oxygen gas, namely the tON injection time, is systematically changed from 0 to 100 % of the pulsing period T. As the tON injection time increases, the chemical composition of as-deposited TaOx films is continuously changed from pure metallic tantalum to the over-stoichiometric Ta2O5 material. Analysis of the crystallographic structure by X-ray diffraction shows that the films adopt the body-centered cubic structure (metallic Ta) for the lowest tON injection time values (oxygen stoichiometry x < 1.0) and become amorphous for the longest tON injection times. It is shown that the tON injection time is a key parameter to produce either homogeneous tantalum oxides, or periodic Ta/TaOx multilayers with alternations close to 3 nm. Similarly, optical transmittance spectra of the film/glass substrate system are recorded in the visible region and the electrical conductivity of the films is measured vs. temperature. Both exhibit a gradual evolution from metallic (300K = 8.17105 S m-1 with a null optical transmittance in the visible range) to semi-conducting (300K = 1.97103 S m-1 with a semi-transparent behavior) and finally to dielectric properties (300K < 10-5 S m-1 for interferential films) as a function of the oxygen concentration in the films.

This paper Numerically investigates the effectiveness of the turbine rotating blade nozzle position on the vortex and film composite cooling performance. The coolant injecting nozzles arranged near the pressure surface side (PS-side-in) .vs. arranged near the suction surface side (SS-side-in) are compared at the rotating speed range of 0-4000rpm with fluid and thermal conjugate approach. Results show that the nozzle position presents different influences under low and higher rotating speed. In terms of the mainstream flow, rotation makes the stagnation line move from the PS-side pressure surface side to the SS-side suc-tion surface side, which changes the coolant film attachment on the blade leading edge surface. The nozzle position however indicates limited influence on the coolant film flow. In terms of the internal channel vortex flow, the coolant injecting from the nozzles forms a high-velocity region near the target wall which brings about enhancing convective heat transfer. The direction of the near wall vortex flow is opposite and align to the Coriolis force direction in both the PS-side-in and SS-side-in, respectively. Therefore, the Coriolis force augments to the heat transfer of the internal vortex cooling in SS-side-in while weakens the internal heat transfer in PS-side-in. Such effects become more intense with higher rotational speed. The blade surface area-averaged dimensionless temperature that inversely proportional to the actual temperature is 7.8% higher in SS-side-in as compared to that in PS-side-in. The SS-side-in suggests more superior composite cooling perfor-mance under the relatively higher rotating speed.

The computational model that is able to estimate the temperature distribution inside a solid specimen during the film boiling phase of immersion quenching (water entry) process has been presented in paper, and it is based on the prescribed initial temperatures of the solid specimen and the liquid quenchant. In addition, the turbulence effects have to be considered using the assumed turbulence kinetic energy value, i.e., the “frozen turbulence” approach, that remains constant thorough the simulation. The studied material is nickel alloy, Inconel 600, for which the extensive experimental data is available. The work has been carried out using ANSYS Fluent computational fluid dynamics software and the methods for solution of Stefan problem by Eulerian two fluid VOF model.. A satisfactory agreement between the experimental and the calculated data has been achieved, yielding thereby the computationally obtained data that fits to a great extent to the prescribed error band of ± 10 % during the estimated film boiling phase of the immersion quenching process itself.

In response to the problem of no supporting equipment for the cultivation of Codonopsis in the hilly and mountainous areas of northwest China, a combined machine for transplanting outcrop of Codonopsis with micro ridge covered with film is designed. The key components of the prototype are analyzed and designed, and the structures and working parameters of the seedbed preparation device, seedling casting device, rotary tillage soil-covering device, film covering device, seedling head burial and film edge soil-covering device are determined. The transmission system scheme is established, and the working mechanism of the core components is analyzed. Field experiments show that when the target seedling spacing is 4.4cm and the machines moves forward at the speed of 0.1, 0.15, and 0.2m/s, the variation coefficient of planting spacing and the qualification rate of planting depth all meet the standard requirements. The qualified rate of planting posture and film side outcrop are greatly affected by the operating speed of the machine, and decrease with the increase of operating speed. When the operating speed reaches 0.1m/s, the average variation coefficient of planting spacing is 0.08%, the average qualified rate of planting depth, planting posture and film side outcrop is 95.83%, 94.17% and 93.33% respectively, which shows that the operating performance is better than that of the operating speed of 0.15m/s and 0.2m/s. This study provides new reference for the theoretical research and design of mechanized and automated transplanting machinery for Codonopsis seedlings.

This work reports the first nanocrystalline SnON (7.6 % Nitrogen content) n-type nanosheet Field-Effect Transistor (nFET) with transistor’s effective mobility (µeff) as high as 357 and 325 cm2/V-s at electron density (Qe) of 5×1012 cm-2 and ultra-thin body thickness (Tbody) of 7 and 5 nm, respectively. At the same Tbody and Qe, these µeff values are significantly higher than single crystalline Si, InGaAs, thin-body Si-on-Insulator (SOI), two-dimensional (2D) MoS2 and WS2. New discovery of slower µeff decay rate at high Qe than SiO2/bulk-Si universal curve was found, owing to one order of magnitude lower effective field (Eeff) by more than 10 times higher dielectric constant () in channel material, which keeps the electron wave-function away from the gate-oxide/semiconductor interface and lowers the gate-oxide surface scattering. In addition, the high µeff is also due to the overlapped large radius s-orbitals, low 0.29 mo effective mass (me*) and low polar optical phonon scattering. SnON nFETs with record-breaking µeff and quasi-2D thickness enable potential monolithic three-dimensional (3D) integrated circuit (IC) and embedded memory for 3D biological brain-mimicking structures.

In this work, nanocomposite photoelectrodes of the TiO2/ Au composition were manufactured, in which the size of plasmonic Au nanoparticles was varied, and the morphology of the TiO2 layer, depending on the thickness, changed from an island to a continuous layer. The influence of the morphology of plasmonic Au nanoparticles and the TiO2 layer on the optical and photoelectrochemical characteristics of hybrid photoelectrodes was studied. It has been shown that continuous coating of Au nanoparticles with a TiO2 layer (layer thickness 10 and 15 nm) leads to a decrease in the photoelectric response, and the decrease in photocurrent density and photoconversion efficiency decreases in proportion to the thickness of the TiO2 layer. The indicated drop in characteristics when plasmonic particles are located under the TiO2 layer is presumably associated with the scattering and recombination of charge carriers in the semiconductor layer. The best performance was shown by a system in which large Au nanoparticles (10 nm) are coated with a 5 nm thick layer of titanium dioxide; in this geometry, Au nanoparticles are decorated with TiO2 nanoparticles, as a result of which the photoelectrode-electrolyte interface has a more complex structure.

Zirconium dioxide (ZrO2) possesses numerous advantages such as high mechanical strength, low friction coefficient, excellent optical properties, and extended lifespan. Consequently, ZrO2 has a broad research foundation and practical significance in functional films and wear-resistant coatings. However, it suffers from brittleness and low ductility when used as a bio-coating material. In this study, a Ta/ZrO2 film was fabricated on Si (100) and titanium alloy substrates using a magnetron sputtering system, with tantalum (Ta) serving solely as a transition layer. Subsequently, Zr and Nb ions were implanted into the film at varying doses but with consistent energy levels. The analysis focused on the film's microstructure, mechanical properties, hydrophilicity, and corrosion resistance. The results demonstrated a significant improvement in the hydrophilicity and corrosion resistance of the ZrO2 film following the implantation of Zr and Nb ions. First-principles calculations based on density functional theory (DFT) principles indicated that, with increasing doping concentrations of Zr and Nb in the ZrO2 model, the stability of the model increased gradually, thereby enhancing its corrosion resistance.

Abstract: The expansion of global industries results in the release of harmful volatile acid vapors into the environment, posing a threat to various life forms. Hence, it's crucial to prioritize the development of swift sensing systems capable of monitoring these volatile acid vapors. This initiative holds great importance in safeguarding a clean and safe environment. This paper presents the synthesis and characterization of pyrene-based covalent organic frameworks (COFs) demonstrating exceptional crystallinity, thermal stability, and intense fluorescence. Three COFs—PP-COF, PT-COF, and PE-COF—were synthesized, showcasing large surface areas and robust thermal stability up to 400 °C. The fluorescence properties and intramolecular charge transfer within these COFs were significantly influenced by their Schiff base bonding types and π-stacking degrees between COF layers. Notably, PE-COF emerged as the most fluorescent among the three COFs and exhibited exceptional sensitivity and rapid response as a fluorescent chemosensor for detecting HCl in solution. The reversible protonation of imine bonds in these COFs allowed for the creation of highly sensitive acid vapor sensors, showcasing a shift in spectral absorption while maintaining structural integrity. This research highlights the potential of COFs as reliable and reusable sensors for detecting harmful acid vapors, addressing environmental concerns arising from industrial activities.

In this study, a composite film was developed for electrochemical sensing of tryptophan (Trp). Porous reduced graphene oxide (PrGO) was utilized as the electron transfer layer, and a C-undecylcalix[4] resorcinarene Langmuir-Blodgett (CUCR-LB) film served as the molecular recognition layer. Atomic force microscopy (AFM), transmission electron microscopy (TEM), Raman spectroscopy, scanning electron microscopy (SEM), and electrochemical experiments were employed to analyze the characteristics of the CUCR-LB/PrGO composite film. The electrochemical behavior of Trp on the CUCR-LB/PrGO composite film was investigated, revealing a linear response range of Trp was 1.0×10-7 to 3.0×10-5 mol L-1 and a detection limit of 3.0×10-8 mol L-1. Furthermore, the developed electroanalytical method successfully determined Trp content in an amino acid injection samples. This study not only introduces a rapid and reliable electrochemical method for determination of Trp but also presents a new strategy for constructing high-performance electrochemical sensing platforms.

The effects of the coolant pulsation and the film cooling with the plasma aerodynamic actuation (PAA) could be herein explored via large eddy simulations. The electrohydrodynamic force derived from the PAA was solved through the phenomenological plasma model. The Strouhal number of the sinusoidal coolant pulsation and the averaged pulsation blowing ratio were 0.25 and 1.0, respectively. Comprehensive analyses were carried out on the time-averaged flow fields, and the results revealed that the pulsed cooling jet might cause a deeper penetration into the crossflow, and this phenomenon could be remarkably mitigated by the downward force of the PAA. Furthermore, because of the coolant pulsation, the counter rotating vortex pair (CRVP) expanded to lifted off the wall less well, and the PAA lessened the negative lift-off impact and entrapment from the CRVP. Then, the spatial-temporal development of the coherent structures was figured out by the alterations of the centerline temperature, reflecting formation of the intermittent coherent structures rather than hairpin vortices due to the coolant pulsation, and their size and upcast behaviors were reduced by the PAA. Consequently, there was a basic suppression of the turbulent mixing of the cooling fluid with the crossflow. Finally, the three-dimensional streamlines confirmed that the coherent structure dynamic behaviors were significantly regulated by the PAA for alleviating the adverse influences of the coolant pulsation. In summary, through controlling how the dominating coherent structures evolve throughout time and space, the PAA can effectively increase the pulsed film cooling efficiency.

With the escalating water scarcity in agriculture, a novel water-saving technique has emerged: drip irrigation with plastic-film mulch (DI). Root function is crucial for sustaining rice production, and understanding its response to DI is essential. However, few studies have evaluated root systems in rice varietals and examined which kind of root system contributes to improving rice grain yield and water productivity in DI. To fill this knowledge gap, we conducted a two-year field experiment comparing two irrigation systems: continuous flooding (CF) and DI. We analyzed their effectiveness with four rice varieties, including upland, F1 lowland, animal feed lowland, and lowland varieties. Vertical root distribution, root bleed-ing rate, photosynthetic-associated parameters, water productivity, and yield performance were analyzed. In our study, the average grain yield of varieties in the DI system (6.4t/ha) was equivalent to those in the CF system (6.6 t/ha). Compared to CF, DI demonstrated significant water-saving potential, saving approximately 35% of the total water supplied, resulting in higher water productivity. Among the varieties, the deep-root weight of the upland variety significantly increased by 51%. The deep-root ratio was positively correlated to transpiration rate, grain yield, and water productivity, which suggested that it contributed to high transpiration, thus maintaining a high carbon assimilation rate resulting in high yield and water productivity. Therefore, deep roots deserve consideration as a trait potentially corresponding to high yield under DI.

In this study, various diamine monomers were used to synthesize aramid polymer films via a low-temperature solution condensation reaction with diacid chloride. For diamines with relatively high basicity, the reaction system became opaque because amine salt formation inhibited polymer synthesis. Meanwhile, low-basicity diamines with strong electron-withdrawing groups, such as CF3 and sulfone, were smoothly polymerized without amine salt formation to provide highly viscous solutions. The acid byproduct HCl generated during polymerization was removed by adding propylene oxide to the reaction vessel and converting the acid into highly volatile inert substances. The resulting solutions were used as varnishes without any additional purification, and polymer films with an excellent appearance were easily obtained through a conventional casting and convection drying process. The films neither tore nor broke when pulled or bent by hand; furthermore, even when heated up to 400°C, they did not decompose or melt. Moreover, polymers prepared from 2,2-bis (trifluoromethyl) benzidine (TFMB) and bis (4-aminophenyl) sulfone (pAPS) did not exhibit glass transition until decomposition. The prepared polymer films showed a high elastic modulus of more than 4.1 GPa and a high tensile strength of more than 52 MPa. In particular, TFMB-, pAPS-, and 2,2-bis (4-aminophenyl) hexafluoropropane-based polymer films were colorless and transparent, with very high light transmittances of 95%, 96%, and 91%, respectively, at 420 nm and low yellow indexes of 2.4, 1.9, and 4.3, respectively.

The effect of neutron irradiation of Si-Ge/Si film structures obtained by gas-phase epitaxy on the processes of charge carrier generation and the magnitude of the dark short-circuit current and open-circuit voltage caused by it is studied, it is shown that their magnitude practically does not change with time. The results obtained indicate that all types of structural defects, both associated with dopant impurities and radiation exposure, contribute to the generation of charge carriers in heated silicon structures with the participation of deep energy levels, which indicates the applicability of neutron processing of silicon materials to create thermal energy converters, operating at high temperatures.

Diamond-like carbon (DLC) films have a promising tribological application in green precision manufacturing, but their toughness represents a serious issue in the way of their application perspective. The film thickness is on the micrometer scale and makes conventional methods unsuitable for its toughness characterization. The absence of an accepted method for characterizing the DLC toughness has hindered the related research on the development of toughening methods and understanding the mechanism. This work intends to explore a relatively simple and acceptable characterization method to measure the film toughness. Moreover, toughening mechanisms of DLC films are proposed during the characterization to reveal the toughening mechanism. The toughness can be fully characterized through combining impact toughness and scratch toughness. The impact toughness can be obtained by observing the size of the indentation and the crack state around the indentation in the impact experiment. The scratch toughness could be assessed by combining the scratch morphology and Crack Propagation Resistance (CPRS). The improvement of film toughness should be carried out from two aspects: preventing microcrack initiation and suppressing crack propagation. Appropriate doping of non-carbide metal particles can effectively improve the toughness of the film, and there are seven main factors affecting the toughening of the film. Five toughening mechanisms of non-carbide metals from film preparation to test stage are revealed during the investigation of the change patterns.

Epitaxial lithium ferrite (LiFe5O8) films with different thicknesses have been successfully fabricated on SrTiO3 (001) substrates by magnetron sputtering deposition technique. The microstructural and magnetic properties are characterized by advanced transmission electron microscope and magnetic measurement device. It was found that the formation of structural defects can be influenced by the thickness of the film. Apart from the misfit dislocations, the orientation domains form in thinner film and twin boundaries appear in thicker film, respectively, contributing to the misfit strain relaxation in the heterosystem. The magnetic measurement shows that the thinner films have enhanced magnetization and a relatively lower coercive field compared with the thicker films containing the antiferromagnetic twin boundaries. Our results provide a way for tuning the microstructure and magnetic properties of lithium ferrite films by changing the film thickness.

Consumers are attracted by the increasing number of available SVOD platforms, but subscribing to all of them would be too expensive. To reduce costs, consumers could combine the use of proprietary subscriptions, non-proprietary subscriptions, and illegal streaming sites. In turn, platforms could enforce access control, a decision that could produce the desired reduction in non-proprietary subscriptions but also an undesired reduction in proprietary subscriptions. The effects of this decision and the determinants of SVOD content demand remain largely unexplored. We propose a baseline model where the SVOD content demand is driven by variety seeking, household financial situation, ethical evaluation, and social norms, as well as a change model where the subscription variation is driven by users’ trait reactance and perceived fairness of the decision. We conducted a survey on the current ways of SVOD content consumption and the responses to a hypothetical access control enforcement, with four randomized versions of the authentication mode. Results confirmed many of the proposed determinants and showed a noteworthy reduction in proprietary subscriptions due to the control enforcement but no effect due to the authentication modes. All these findings may help improve future models on SVOD content consumption and better address the difficult challenge of converting unauthorized users into authorized ones.

Changing the film thickness to manipulate the microstructural properties has been considered as a potential method in practical application. Here, we report that atomic-scale structural properties regulated by film thickness in NiCO2O4(NCO)/CuFe2O4(CFO) bilayer heterostructure prepared on (001)-MgAl2O4 (MAO) substrate by means of aberration-corrected scanning transmission electron microscopy (STEM). The misfit dislocations at NCO/CFO interface and antiphase boundaries (APBs) bound to dislocations within the films both are found in NCO (40 nm)/CFO (40 nm)/MAO heterostructure to contribute to relaxation of mismatch lattice strain. In addition, the non-overlapping a/4[101]-APB is found and the structural transformation of this kind of APB is resolved at atomic scale. In contrast, only the interfacial dislocations form at interface without the formation of APBs within the films in NCO (10 nm)/CFO (40 nm)/MAO heterostructure. Our results provide evidence that formation of microstructural defects can be regulated by changing film thickness to tune magnetic properties of epitaxial bilayer spinel oxide films.

An influenza A virus (H3N2) with an envelope with the same structure as COVID-19 was used for antiviral testing of material surfaces, in comparison with some results of feline calicivirus. The evaluation method used was the film adhesion method, in which the virus solution is placed on the material and adhered to it using a film. The evaluation method was based on the film adhesion method, in which the virus solution is placed on the material and adhered with a film, and the plaque method, in which the cell virus is allowed to infect the material and form plaques, but the appropriate virus concentration must be adjusted to observe the plaques. When not under that restriction, the plaques are often incomplete; this is observed. For this reason, this study applied an area measurement method that can reflect viral activity even when plaques are not obtained. This study revealed that different types of metallic materials have different antiviral properties. Specifically, the antiviral activity of iron, carbon steel, and nickel was relatively high, while that of stainless steel and titanium was relatively low. The order of antiviral activity was as follows: Fe, SS400, Ni, SUS316L, SUS304, and Ti.

ZnO thin films with a thickness of 300 nm were deposited on Si and Al2O3 substrates using electron beam evaporation technique with the aim to be tested as low cost and low power consumption gas sensors for ozone (O3). To characterize the surface roughness and the grain size, which are the main parameters recognized to enhance gas sensitivity since they directly influence the effective sensing area, surface morphology and roughness analyses of the films were performed using scanning electron microscopy and atomic force microscopy, respectively. The crystalline structure and elemental composition were studied through Raman spectroscopy and X-ray photoelectron spectroscopy. Gas tests were conducted at room temperature and zero-bias voltage to assess the sensitivity and response as a function of time of the films to O3 pollutant. The results indicate that the films deposited on Al2O3 exhibit promising characteristics, such as high sensitivity and a very short response time (< 2 s) to the gas concentration. Additionally, it was observed that the films display pronounced degradation effects after a significant exposure to O3.

Human fungal pathogen Candida albicans causes oral infectious diseases such as oral thrush in immunocompromised patients with hyposalivation, diabetes mellitus, prolonged use of anti-biotics or immunosuppressive medicines and poor oral hygiene. An anti-fungal medication classified as a BCS class II drug, Clotrimazole has high permeability and low solubility in water. It is commercially available as lozenges, which do not uniformly distribute the drug within saliva for local therapy. This results in higher dose frequency and lower patient compliance. Therefore, in this study we proposed a niosomal based subgingival film formulation of clotrimazole for enhancing drug efficacy by improving drug solubilization capacity and improving patient compliance by prolonging the release of drug at the targeted site and reducing the dose frequency to show effective anti-fungal activity. The prepared niosomal film showed good entrapment efficiency and anti-fungal activity. Niosomal film showed better release pattern than drug loaded film.

Phosphorus, an essential rare element in aquatic ecosystems, plays a key role in maintaining ecosystem balance. However, an excess of phosphorus will lead to eutrophication and algal pro-liferation. To prevent eutrophication, it is crucial to pretreat and measure the concentration of total phosphorus (TP). Compared with conventional TP pretreatment equipment (autoclave), a lab-on-a-chip detection device fabricated through micro-electromechanical system technology using titania (TiO2) as a photocatalyst is more convenient, efficient, and cost-effective. However, the wide bandgap of TiO2 (3.2 eV) limits the photocatalytic activity. To address this problem, this paper describes the preparation of a TiO2/Au nanocomposite film by electron-beam evaporation and atomic layer deposition, based on the introduction of a gold film and TiO2 on a quartz substrate. The photocatalytic degradation properties of TiO2/Au nanocomposite films with thicknesses of 1, 2, 3, and 4 nm are assessed using rhodamine B as a pollutant. Experimental results demonstrate that the deposition of a gold film with different thicknesses can enhance the photocatalytic degradation efficiency through synergetic reactions in the charge separation process on the surface. The optimal photocatalytic efficiency is achieved when the deposition thickness is 2 nm, and it decreases with further increase in the thickness. When the photocatalytic reaction time is 15 min, the LOC device with a 2-nm-thick gold layer and autoclave exhibit similar TP pretreatment performance. Therefore, the proposed LOC device based on photocatalysis technology can address the limitation of conventional autoclave equipment, such as large volume, long processing time, and high cost, thereby satisfying the growing demand for on-site evaluation.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

Liposome vesicle is an ideal carrier for carbon nanotube (CNT) to serve as the water channel that allows the fast transport of water molecules, and thus enhancing the membrane permeability. However, low quantity of the inserted CNT in the liposome vesicle is an important factor that limited further improvement of the membrane flux. In present study, positively charged lipids (2,3-dioleoyloxy-propyl)-trimethylammonium-chloride (DOTAP) was introduced to the 1,2-dioleoyl-sn-glycero-3-phosphoethanolamineon (DOPE) liposome vesicles to tailor the vesicle charge, so as to evaluate the effect of positively charged DOTAP on the insertion of CNT into liposomes and separation performance of thin-film nanocomposite (TFN) membranes. The results showed that addition of DOTAP induced more quantity of CNT inserted into the liposome vesicles, since the shrinkage rate (k) and permeability (Pf) of liposome vesicles present obvious increase with increased content of DOTAP in the liposome vesicles. Besides, it contributed to 252.3% higher water flux for TFN membranes containing DOPE/DOTAP2:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 2:1) than TFC membranes. More important, it presented 106.7% higher water flux for TFN membranes containing DOPE/DOTAP4:1-CNT liposomes (the mass ratio between DOPE and DOTAP was 4:1), which was originated from the more water channels that the CNT provided in the liposome vesicles. In all, positively charged DOTAP effectively tailored the vesicle charge, which provided a better carrier for the insertion of more quantity of CNT, and contributed to higher permeability of TFN membranes.

This work explores five falling film evaporator (FFE) simulation approaches combined with energy consumption minimization strategies, namely Mechanical Vapor Recompression and Thermal Vapor Recompression (MVR and TVR respectively). Global system analysis and advanced dynamic optimization strategies are then investigated to minimize steam consumption, the cost of steam, the total annualized cost and maximizing product yield. The results indicate that a higher TVR discharge pressure, or MVR compression ratios, along with higher feed temperatures enhance evaporation with but increase operational costs. The most economic option includes three evaporator effects with TVR for achieving 50% product dry mass content. However, for a 35% dry mass content, MVR becomes cost-effective with an 11% reduction in unit electricity prices or a simultaneous 7% drop in electricity prices and a 5% increase in gas-based steam prices. Furthermore, switching from milk powder production to milk concentrates, an annual cost reduction ranging from 10.75 to 44% is achieved. Also, a forecasted 20% (or more) reduction of biomass-based steam cost can lead to lower annual expenditure comparing with the nominal NG-based steam Case. Regarding the total annualized cost, for a new plant design, optimization strategies lead to a 9 - 45% reduction in the total cost depending on the Case under consideration.

A new biodegradable paper-based film is a hot research topic in the development of green agriculture. In this paper, a black paper base film coated with cooked tung oil with excellent mechanical properties, hydrophobic surface, high heat transfer and strong weather resistance was prepared by spraying high pigment carbon black solution on the surface of base paper. The results showed that the surface solidified oil film with rough structure was made by the brush coating process of cooked tung oil, and the base film of black paper was given hydrophobic structure, and the contact angle reached 98.9 °. Cooked tung oil permeates into the inside of the paper base, and after curing, it forms a multi-dimensional network film structure. The maximum tensile stress of the black paper base film is about 123% higher than that of the original paper base film. The coloring of carbon black makes the black paper base film have heat conduction effect, and the average heat transfer rate reaches 15.12 °C/s. Cooked tung oil is combined with the paper-based fiber high-toughness layer to form a stable system. The existence of the cured film improves the basic mechanics and hydrophobicity, and the resistance to ultraviolet radiation and hot air is greatly improved. This study provides a feasible scheme for the application of a black paper base film coated with cooked tung oil.

The application of dry lubrication in rolling contacts is challenging due to wear. In previous studies graphene platelets applied as dry lubricants on the surfaces of angular contact ball bearings demonstrated superior properties. These specific bearings, experiencing both rolling and spinning motion, create more severe conditions for dry lubricants. The applied graphene platelets have a thickness of few graphene layers in the nm range and a diameter in the µm range. Such platelets can be produced by mechanical exfoliation from graphite. To delve deeper into the lubrication effects, investigations were carried out using a milli tribometer. In the tests, a fixed steel ball is sliding against an oscillating counterpart under defined load. During the measurements, the applied load and tangential forces on the ball are recorded to calculate the friction. In our case, a steel ball with a diameter of 6 mm was used against graphene-based films on flat bearing surfaces (axial bearing washer). Comparative investigations included nano graphite particles and fullerene as dry lubricants, in addition to graphene platelets of various staple thicknesses. To increase the adhesion of the films to the surfaces, a pre-rolling process was implemented. Afterwards, the friction on the compressed films was measured. The results indicate that the pre-rolling process effectively reduces the friction of the system. After testing, the surfaces underwent analysis using laser scanning microscopy to assess the formed films, wear, and material transfer. It has been demonstrated that the pre-rolling process leads to the formation of a very thin compacted film with surface protective properties. On the ball as counterpart, the graphene platelets generate a transfer film on the contacting surface.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

Current microbiological methods for pneumonia diagnosis require invasive specimen collection and time-consuming analytical procedures. There is a need for less invasive and faster methods to detect lower respiratory tract infection. The analysis of volatile metabolites excreted by pathogenic microorganisms provides the basis for developing such a method. Given the synergistic role of Candida albicans in increasing the virulence of pathogenic bacteria causing pneumonia and the cross-kingdom metabolic interactions between microorganisms, we compare the emission of volatiles from Candida albicans yeasts and the bacteria Staphylococcus aureus using single and mixed co-cultures and apply that knowledge to human in vivo investigations. Gas-chromatography-mass spectrometry (GC-MS) analysis resulted in the identification of sixty-eight volatiles that were found to have significantly different levels in cultures compared to reference medium samples. Certain volatiles found in co-culture originated mainly from C. albicans metabolism (e.g., isobutyl acetate), whereas other volatiles primarily came from S. aureus (e.g., ethyl 2-methylbutyrate). Isopentyl valerate reflects synergic interactions of both microbes, as its level in co-cultures was found to be approximately three times higher than the sum of its amounts in monocultures. Hydrophilic-lipophilic balanced (HLB) coated meshes for thin-film microextraction (TFME) were used to pre-concentrate volatiles directly from bronchoalveolar lavage (BAL) specimens collected from patients suffering from ventilation-associated pneumonia (VAP) that was caused explicitly by C. albicans and S. aureus. GC-MS analyses confirmed the existence of in vitro-elucidated microbial VOCs in human specimens. Significant differences in BAL-extracted amounts respective to the pathogen causing pneumonia were found. The model in vitro experiments provided evidence that cross-kingdom interactions between pathogenic microorganisms affect the synthesis of the volatile compounds. The TFME meshes coated with HLB particles proved to be suitable for extracting VOCs from human material, enabling the translation of in vitro experiments on the microbial volatilome to the in vivo situation involving infected patients. This indicates the direction that should be taken for further clinical studies on VAP diagnosis based on volatile analysis.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

The undoped and tungsten (W)-doped vanadium dioxide (VO₂) thin films were prepared by electron beam evaporation associated with ion-beam assisted deposition (IAD). The influence of different W-doped contents (3%-5%) on the optical, electrical, structural, and thermos-mechanical properties of VO₂ thin films was investigated experimentally. Spectral transmittance results showed that with the increase of W-doped contents, the transmittance in the visible light range (400-750 nm) decreases from 60.2% to 53.9%, and the transmittance in the infrared wavelength range (2.5 μm to 5.5 μm) drops from 55.8% to 15.4%. As the W-doped content increases, the residual stress in the VO₂ thin film decreases from -0.276 GPa to -0.238 GPa, but the surface roughness increases. For temperature-dependent spectroscopic measurements, heating the VO2 thin films from 30°C to 100°C showed the most significant change in transmittance for the 5% W-doped VO₂ thin film. When the heating temperature exceeds 55°C, the optical transmittance drops significantly, and the visible light transmittance drops by about 11%. Finally, X-ray Diffraction (XRD) and scanning electron microscope (SEM) were used to evaluate the microstructure characteristics of VO₂ thin films.

This paper is the second part of a two-part report studying the responses of a typical point-contact elastohydrodynamic lubrication (EHL) problem to multiscale roughness that is mimicked by artificially generated waviness with different amplitudes, frequencies, and directions. The previous Part I paper (doi:10.3390/lubricants10120368) focuses on the full film regime, while the current paper focuses on the partial film regime. The amplitudes and frequencies are related to the feature geometry of smooth EHL problems. Generated waviness is input to a transient thermal EHL model. The simulation is conducted 1,600 times for different waviness parameters, loads, and speeds. Eight performance parameters are extracted: the asperity contact ratio, minimum film thickness, maximum pressure, central point film thickness, central point pressure, mean film thickness, coefficient of friction (COF), and the maximum temperature rise. The ratios of the first seven parameters with and without waviness and the asperity contact ratio values are plotted on the frequency–amplitude coordinate plane as contour maps. The influences of the amplitude, frequency, wave direction, load, and speed on the eight performance parameters are analyzed and summarized. The simulated data and plotted contour maps are provided to the readers in the Supplementary Material.