This study focused on the optimization of the flexural strength of bio-composite samples of palm kernel, whelks, clams, periwinkles shells and bamboo fiber, reinforced with resin for engineering applications. The aim of the study was to: formulate different samples of bio-composite reinforce with resin for engineering applications and to evaluate the flexural strength, of the fabricated composite. The hand lay-up technique was used for the composites produced by incorporating different percentage compositions of the shells/fiber (10%, 15%, 20%, 25% and 30%) into varied proportions of epoxy resin and catalyst. The cured samples after 24hours were subjected to tensile, impact, flexural and water absorption test. The experiments were conducted using Taguchi optimization method L25 (5x5) with five design parameters and five level combinations in Minitab 18 statistical software. The results showed that the average values of flexural was 114.87MPa when compared to the unreinforced of 72.33MPa bio-composite. The study recommended that agricultural waste like palm kernel shells, whelk shells, clams, periwinkle shells and bamboo fiber, should be converted into important engineering applications.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

Dental polymers are often advertised and selected for use in restorations based upon the flexural strength of prefabricated discs, which may not accurately reflect their performance in dental applications. The objectives of this study were, therefore, to determine whether the three-point bending (3PB) test for flexural strength would be predictive of the “crunch-the-crown” CTC test for the failure load. Three brands of polymers (Trilor, Juvora, and Pekkton) were fabricated into rectangular bars and fully contoured crowns (10 specimens of each polymer brand, 30 specimens of each shape). Bars were tested in 3PB to determine flexural strength, and crowns were CTC tested to determine failure load after luting to resin abutments. Statistical significance was evaluated by one-way ANOVA ( = 0.05) and Pearson’s correlation coefficient. The fracture mechanisms were characterized by scanning electron microscopy (SEM). There were significant differences (p < 0.05) in the mean crown failure loads (Trilor [7,033 N] > Juvora [5,217 N] > Pekkton [3,023 N]) and mean flexural strengths of the bars (Trilor [468 MPa] > Juvora [197 MPa] = Pekkton [192 MPa]). There were no correlations between flexural strength and failure load. The mode of crown fracture was different between the polymers, and included deformation (Juvora), ductile-to-brittle fracture (Pekkton), and a combination of cracks and deformation (Trilor). The flexural strength was not correlated with the corresponding crown failure load. Dental practitioners should not rely on the value of flexural strength obtained from the three-point bending test, as advertised from the manufacturer, to predict the performance of polymeric crowns.

As a crucial part of head protection equipment, research on the material and structural application of helmet liners has always been a hot topic in the field of helmet manufacturing. This paper aims to introduce the most common helmet liner materials, including traditional polystyrene, polyethylene, polypropylene, and others, as well as emerging materials such as anisotropic materials, and polymer nanocomposites. In addition, the design principles of helmet liner structure are discussed, including the evolution of multi-layer structure, integration of geometric irregular bubbles, etc., to enhance energy absorption capacity. Advanced manufacturing processes such as additive manufacturing technology are introduced to fabricate complex structures. Finally, the application of biomimetic structures in helmet liner design is explored. For example, the structure of biological tissue can be used to design a helmet liner structure with superior energy absorption performance. On this basis, the idea of bionic structures is extended to the combination of plant stalks and animal skeletal structures, and additive manufacturing technology is used to significantly reduce energy loss during elastic yield energy absorption, thus designing a reusable helmet. This provides a promising research direction for future helmet liner materials and structural applications.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

In polymer-based dental composites, wear is a three-body wear system mainly abrasive, because of the food particles and wear products suspended in the oral cavity, which are transferred to the microcavities of the surface of the replacements. Due to this fact, the incorporation of nanodiamond as reinforcement in these polymer matrix composites, which promotes the creation of a solid lubricant tribofilm surface could be advantageous. When nanodiamond is added in contents of 0.8, 1.6 and 3.2 wt %, an increase in microhardness from 95 up to 420 %, compared to the one of neat BisGMA/TEGDMA, is observed. Additionally, the incorporation of a content of 1.6 wt % is enough to cause a diminution of ~78 % in the friction coefficient and a reduction of the specific wear rate and Archard’s coefficient of ~50 %. Nevertheless, the addition of relatively high contents reduces the effectiveness of photoinitiation and UV-curing, which is related to the scattering and absorption of UV radiation by ND.

Introduction: To indentify the most effective actors(authors, countries, and journals) about composite resin restorations in the period 2000-2020.Material and Methods: An electronis research was conducted in the Scopus database by selecting the words ‘composite resin’ and ‘restoration and English language, article and review types, dentistry field. Their bibliometric data including publication title, authorship, citation count, citation dentistry, year of publication, country and institution of origin, journal of publication, study design, and keywords were extracted and analyzed.Results and Discussion: To our knowledge, this is the first bibliometric article on composite resin restorations. This study provides information about authors, institutions and countries that contribute to significant improvements in composite resin restorations. From 2000 to 2020, there were 7118 articles published from 99 countries.Articles originate primarily from the USA and Brazil. Results indicate that the USA, Brazil, Germany, Turkey, the United Kingdom, Japan, Swtizerland, Italy, Netherlands and India are the leading countries in composite resin restoration research and account for 51.8% of the total number of publications. The total number of citations are 158.404, corresponding to 22 citations per paper publication. During the time period examined, 776 hot articles and 228 classic articles on composite resin restorations were found.The journal with the most publications is ‘Operative Dentistry’. The publishing houses of the top 10 journals are from 4 countries: USA(6),Netherlands(2),Germany(1),Japan(1). The most cited article within the boundaires of this study is Ferracane’s article titled ‘Resin composite-State of the art’, which was published in Dental Materials in 2011 and received 913 citations.

Purpose: This study aimed to evaluate the nanomechanical properties and chemical composition of restorative materials and dental surfaces using different toothpastes. Methods: Enamel (n=60) and dentin (n=60) bovine blocks were obtained and restored using resin-modified glass ionomer cement (RMGIC, n=30) or composite resin (CR, n=30) to form the dentin adjacent to RMGIC (DRMGIC), enamel adjacent to RMGIC (ERMGIC), dentin adjacent to CR (DCR), and enamel adjacent to CR (ECR). After restoration, one hemiface of each specimen was coated with an acid-resistant varnish to create the control (C) and eroded (E) sides (erosion: 5 days, 4 × 2 min/day; 1% citric acid / abrasion: 2 × 15 s followed by immersion on slurries 2 min). Three toothpastes were used: without fluoride (WF; n=10), sodium fluoride (NaF; n=10), and stannous fluoride (SnF2; n=10). The specimens were analyzed for nanohardness (H), elastic modulus (Er), and chemical composition using energy-dispersive X-ray spectroscopy (EDS) and Raman microscopy. Data were analyzed using ANOVA two-way repeated measures and Tukey’s test (α = 0.05). Results: The NaF presented lower values of H for DRMGIC-C, with a statistical difference for WF (p < 0.05). SnF2 resulted in lower Er values for ERMGIC-E and RMGIC-E than WF and NaF (p < 0.05). WF showed lower calcium and phosphorus concentrations for DCR-E than other types of toothpastes (p < 0.05). Only stannous-based toothpaste damaged the elasticity of eroded glass ionomer restorations performed in enamel. Toothpastes with fluoride was capable for maintaining main chemical elements of dentin adjacent to restorative materials under challenge conditions.

Fiber-opening treatment of commingled yarns consisting of thermoplastic nylon fibers and carbon fibers could produce superior CFRTP, but few studies toward that end have been conducted. In this study, we investigated whether an open weave fabric consisting of commingled yarns made of carbon and nylon fibers could shorten the impregnation distance of resin to carbon fibers, and there are few reports on the design of fabrics by opening carbon fiber bundles consisting of commingled yarns. From this study, following are cleared. The impregnation speed of the nylon resin on the carbon fiber was very fast, less than 1 minute. As the molding time increased, the tensile strength and tensile fracture strain slightly decreased and the nylon resin deteriorated. The effects of molding time on flexural strength, flexural modulus, and flexural fracture strain were negligible. From the cross-sectional observation conducted to confirm the impregnation state of the matrix resin, no voids were observed in the molded products regardless of molding time or molding pressure, indicating that resin impregnation into the carbon fiber bundle of the open-fiber mixed yarn fabric was completed at a molding pressure of 5 MPa and a molding time of 5 min.

Literature revealed the potential of using guayule resin for asphalt cement replacement from the binder’s perspective. However, monitoring guayule resin through binder-aggregate mixture could disclose its performance through field. In this study, designated binders were employed to investigate the applicability of such an innovative replacer through mixture, which were neat asphalt and guayule-based binders (neat guayule, asphalt-rubber-guayule, guayule-rubber binders). Consecutively, field-simulated lab mixtures were prepared to investigate the major distresses. Moisture damage, rutting, fatigue cracking, and thermal cracking resistances were investigated using the modified Lottman (TSR) test, rut test by asphalt pavement analyzer (APA), semi-circular bending (SCB) test, and disk-shaped compact tension (DCT) test, respectively. Additionally, the Hamburg wheel-tracking (HWT) test was employed to evaluate moisture susceptibility and rutting resistance. Outcomes revealed that the neat guayule was susceptible to moisture damage at a 7% air content (V_a) when the TSR test was employed. In contrast, all investigated mixtures yielded perfect performances against moisture susceptibility under the HWT test. Guayule-based mixtures perfectly resisted rutting, as analyzed by the rut test and HWT test. Generally, changing parameters (e.g., V_a, rubber addition, and partial asphalt replacement by guayule and rubber) enhanced the guayule-based mixture resistance to rutting and moisture damage resulting in acceptable performances. Guayule-based mixture had a high fracture toughness at low temperatures, hence fatigue fracture resistance at intermediate temperatures. Neat guayule mixture with or without rubber addition did not entirely resist thermal fracture. However, partial asphalt replacement by guayule and rubber resisted the thermal fracture to a great extent.

Agricultural wastes have posed as a treat to the environment over the years and they are found in large quantities due to domestic and industrial utilization of such materials in under developed and developing countries. The inability to recycle this waste has led to researches on how to use them in carrying out productive industrial activities. The aim of this study is to use Central Composite Design (CCD) to optimize the bleaching effects by snail shell as adsorbents on crude palm oil. The predictive ability of the model was close to accurate using MINITAB 19 software with the design application for the process simulation for % FFA yield to have 75.856% for experimental and 77.587% for predicted yield with just 1.731% residual. The saponification value increased with adsorption, and it indicates that palm oil can be used for soap making.

This paper considers a new approach to the modeling of the vacuum infusion process at the manufacturing three-dimensional composite parts of complex shape. The developed approach and numerical methods are focused on the reliable prediction with the needed accuracy and elimination the unrecoverable defect of composite structure such as the dry spots. The paper presents some experimental results, which demonstrate two cases of dry spots formation in large aircraft composite panels, and analyses the reasons of these defects arising. Our numerical technique is based on the vacuum infusion of the liquid resin into porous preform as the two phase flow, which is described by the phase field equation coupled with the Richards equation describing the fluid motion in unsaturated soils with spatially varied pressure dependant porosity and saturation. This problem statement allowed to correctly reconstruct the resin front motion and formation of inner and outer dry spots depending on its movement. For the rapid detection of preform zones that are suspicious for defect formation two indicators calculated during process simulation are proposed and tested at the numerical experiments. The auxiliary program tool has been developed in MATLAB environment to correctly detect the times of formation, localization and dimensions of the arising dry spots by using the results of the finite element model simulation.

Nano/micron-sized bioactive glass (BG) particles are attractive candidates for both soft and hard tissue engineering. They can chemically bond to the host tissues, enhance new tissue formation, activate cell proliferation, stimulate the genetic expression of proteins, and trigger unique an-ti-bacterial, anti-inflammatory, and anti-cancer functionalities. Recently, composites based on bi-opolymers and BG particles have been developed with various state-of-the-art techniques for tis-sue engineering. Gelatin, a semi-synthetic biopolymer, has attracted the attention of researchers because it is derived from the most abundant protein in the body, viz., collagen. It is a polymer that can be dissolved in water and processed to acquire different configurations, such as hydro-gels, fibers, films, scaffolds, etc. Searching "bioactive glass gelatin" in the tile on Scopus renders 80 highly relevant articles published in the last ~10 years, which signifies the importance of such composites. First, this review addresses the basic concepts of soft and hard tissue engineering, in-cluding the healing mechanisms and limitations ahead. Then, current knowledge on gelatin/BG composites including composition, processing and properties is summarized and discussed both for soft and hard tissue applications. This review explores physical, chemical and mechanical features and ion-release effects of such composites concerning osteogenic and angiogenic respons-es in vivo and in vitro. Additionally, recent developments of BG/gelatin composites using 3D/4D printing for tissue engineering are presented. Finally, the perspectives and current challenges in developing desirable composites for the regeneration of different tissues are outlined.

Bamboo engineering materials are green, high-strength, tough, durable, and structurally safe, and have promising application prospects in various modern green and low-carbon buildings. To invest the vibration behavior of new bamboo bundle veneer -laminated lumber (BLVL) for use in floor slabs, this study designed two kinds of full-scale vibration tests under a pedestrian load: an extraction hammer impact test, and a static concentrated load test, it is expected to provide theoretical and data support for the application of bamboo bundle veneer laminated composite materials in the construction field. The results showed that the self-oscillation frequency and mid-span deflection of the BLVL composite met the requirements of multiple relevant regulations when used as the structural material of floor slabs. The BLVL floor slab had a higher flexural stiffness and better vibration-damping performance than the OSB floor slab. The first-order self-oscillation frequency of the BLVL composite floor slab was 13.769 Hz, the damping ratio of the first three orders of modalities was 1.262–2.728%, and the maximum static deflection in the span of the joist was 0.932 mm under a 1 kN concentrated load. The 1 kN static deflection of the BLVL was reduced by 22.33%, and the root mean square (RMS) acceleration of the walking load response was significantly lower than that of the OSB floor slab. The preparation of BLVL composite materials by homogeneous lamination of bamboo bundle veneer and wood veneer may help improve the vibration behavior of bamboo-wood structures such as floor slabs and walls.

This research seeks to interpret the component analysis of an innovative bio-asphalt binder using guayule resin in addition to crumb rubber modifier (CRM) at high concentrations. Such asphalt modification aims to minimize the dependency on virgin asphalt binder and provide new solutions concerning sustainable, flexible pavement industry. Guayule resin is a promising bioresource for asphalt binder replacement. By now, it could be considered a no value byproduct extracted during the guayule natural rubber production. CRM is a recycled material derived from scrap tires. The provided interpretation could help in understanding the asphalt-rubber-guayule interaction mechanism. Fourier transform infrared spectroscopy (FTIR), supported by thermo-gravimetric analysis (TGA), was used to investigate the component analyses of guayule resin composition, asphalt guayule interaction, and asphalt rubber guayule interaction, compared to corresponding asphalt rubber interaction. Additionally, the rheological properties at elevated temperatures were provided to link the microscale properties with the final product performance. The study clarified the distinct carbon and hydrogen compositional elements of guayule resin. Asphalt and guayule resin have similarities in chemical composition and rheological behavior with temperature susceptibility. The asphalt guayule binder had physical interaction. However, when both interacted with rubber, a chemical interaction was attributed, with no difference in rubber dissolution tendency, in asphalt rubber guayule, compared to asphalt rubber. A bio-binder composed of 62.5% asphalt, 25% guayule and 12.5% CRM had the potential to provide rheological properties better than base asphalt. Such behavior was interpreted by a high release of rubber components.

Objectives: The current study aimed to compare the adaptation of the restored class-I cavities with two self-etch adhesives bonded to two resin composite using cross-polarization optical coherence tomography (CP-OCT). Materials and Methods: Cylindrical class-I cavities were prepared on twenty, extracted human premolars. Two self-etch adhesives; Clearfil SE bond 2 (SE; Kuraray Noritake Dental, Japan) and Bond Force (Palfique Bond) adhesive (PL; Tokuyama Dental, Japan) were used in this study that were bonded to either resin composites materials; Herculite XRV microhybrid dental composite (HRV; Kerr, Italy) or Estelite Alpha composite (ESA; Tokuyama Dental, Japan). The specimens were divided into four groups (n=5); SE-HRV, SE-ESA, PL-HRV and PL-ESA. All specimens were varnished and stored in distilled water for 24h. Then, they were submerged in a contrasting medium. After that, all groups were optically imaged under CP-OCT at every 250 µm interval distance. Later, image binarization and gap quantification were carried out using Image analysis software. Result: There was a significant difference between all the groups except between SE-ESA and PL-ESA (p = 0.51). The highest median gap % was seen in PL-HRV group followed by SE-ESA, PL-ESA and SE-HRV. Conclusion: Other than composite filler loading and adhesive formula, the interactions of the adhesive and composite copolymers have great influence on composite adaptation.

One century ago, ferroelectricity and then piezoelectricity were discovered using Rochelle salt crystals. Today, modern societies are invited to switch towards a resilient and circular economy model. In this context, this work proposes a method to manufacture piezoelectric devices made from agro-resources such as tartric acid and polylactide significantly reducing the energy budget without requiring any sophisticated equipement. These piezoelectric devices are manufactured by liquid phase epitaxy grown Rochelle salt (RS) crystals into a 3D printed poly(Lactic acid) (PLA) matrix being the artificial squared meshes which mimic the natural wood anatomy. This composite material can easily be produced in any fablab with renewable materials and at low processsing temperatures, reducing then the total energy consumed. Manufactured biodegradable samples are fully recyclable and have good piezoelectric properties without any pooling step. The measured piezoelectric coefficients of manufactured samples are higher than many piezoelectric polymers such as PVDF-TrFE.

Naturally-derived synthetic leather is a widely used and high-quality type of faux leather or synthetic leather. Many consumers prefer authentic leather goods due to their exceptional qualities, including high water vapor permeability and superior wearing comfort. Consequently, the exploration of artificial leather made from natural materials with exceptional qualities as an alternative to genuine leather has garnered significant interest and is now a highly studied subject. Synthetic leather, sometimes known as imitation leather, has gained popularity recently as a highly suitable alternative to genuine leather. Continuous advances in this area of research increase the range of uses for synthetic leather using natural fibers. Thus, this research aims to explore synthetic leather materials using orange peel waste, which can be applied to the fashion industry. This research applies several types of orange peel waste, such as Pomelo, Sweet orange, and Sunkist orange, to different compositions and strengthening materials, such as bandages and dacron. The resulting bio-composite materials' morphology, mechanics, and adhesive properties were evaluated following ASTM D 2209-00 and ASTM D 4533-04 standards. The results indicate that specimen 1A (Pomelo using bandage as reinforcement) has the most significant effects, with a tensile test value of approximately 472 N/cm2, an elongation of roughly 67.28 % was the highest value on sweet orange using bandage as reinforcement, and a tear resistance of around 14.28 N/cm2 for Pomelo with bandage as reinforcement. Furthermore, the test results also show that composition 2B still does not meet the standards of SNI 1294:2009 and ISO 3376 for tensile strength and ISO 3377-1 for tear strength. Additionally, statistical analysis showed no appreciable changes in the samples analyzed. Furthermore, statistical evaluations showed no significant alterations in the studied samples. The results of this experimental investigation can be explored further and used as a basic framework for the creation of bio-composites from orange peel waste for future fashion.

High density polyethylene (HDPE) and poly(lactic) acid (PLA) blends with different ratios of both polymers, namely 30:70, 50:50 and 70:30, were produced. Polyethylene grafted maleic anhydride and a random copolymer of ethylene and glycidyl methacrylate, were also proposed as compatibilizers to modify HDPE-PLA optimal blends and were added in the amounts of 1, 3 and 5 wt.%. Blends properties have been evaluated through different aspects by performing tensile tests, scanning electron microscopy to analyze blend morphology and interfaces, and thermomechanical analysis through differential scanning calorimetry, thermo-gravimetric analyses and infrared spectroscopy. The second blend, the one with equal amounts of HDPE and PLA seems to represent a good balance between high amount of bio-derived charge and acceptable mechanical properties. This suggests a good potential of these blends, which would be a good starting point for the production of composites with lingo-cellulosic fillers.

Synthetic materials such as Carbon, Kevlar, and Glass fibers are extensively utilized in various industries due to their superior characteristics including high stiffness, great strength, low den-sity, and high wear resistance, these advantages contributed to making them widespread in ap-plications like; aerospace, automobile, civil and electronics. This research is carried out to enhance the creep compliance of epoxy composite material by considering two types of fibers as reinforcement. A composite material is produced by combining two fibers, Kevlar fiber mixed with sika epoxy resin, along with Carbon fiber also mixed with sika epoxy resin using a Hand-Layup process. Experiments and numerical modeling are examined to offer a comprehensive understanding creep behavior of epoxy composite material in different weight ratios. Burger and Prony models are used to represent stress relaxation and creep strain of Visco-elastic material. According to the results, sika epoxy resin reinforced with Kevlar and Carbon fibers exhibits enhancement in the mechanical properties compared with pure epoxy. The use of Kev-lar/Sika epoxy composite results in higher creep compliance and modulus of elasticity compared with Carbon/Sika epoxy composite.

Natural astaxanthin is a precious substance obtained from some organisms such as microalgae. This plant has many benefits for humans, so research into its cost-effective and economical production has recently increased. For this purpose, some methods such as the use of different culture media, gene engineering, different stresses, nanoparticles, bio acids, and phytohormones are important. Accordingly, this review study was conducted to demonstrate the effect of the factors mentioned above for the high production of astaxanthin in microalgae, especially Haematococcus pluvialis (H.p).

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

Addressing the issue of low bonding strength in Ti/Mg laminated composites due to interfacial oxidation, this study employs a differential temperature rolling method using longitudinal induction heating to fabricate Ti/Mg composite plates. The entire process is conducted under an argon gas protective atmosphere, which prevents interfacial oxidation while achieving uniform deformation. The effects of reduction on the mechanical properties and microstructure of the composite plates are thoroughly investigated. Results indicate that as the reduction increases, the bonding strength gradually increases, mainly attributed to the increased mechanical interlocking area and a broader element diffusion layer. This corresponds to a transition from brittle to ductile fracture at the microscopic tensile-shear fracture surface. When the reduction reaches 47.5%, the Ti/Mg interfacial strength reaches 63 MPa, which is approximately a 20% improvement compared to the bonded strength with previous oxidation at the interface. Notably, at a low reduction of 17.5%, the bonding strength is significantly enhanced by about 1 time. Additionally, it is found that a strong bonded interface at high reduction is beneficial in hindering the propagation of interfacial cracks during tensile testing, enhancing the ability of the Ti/Mg composite plates to resist interfacial delamination.

In this study, the elastic properties of composite materials are investigated, considering the effects of separation of fiber-matrix joint boundary and matrix failure. In this method, by assuming periodic microstructure and using a linear approximation of the displacement field by applying continuity and equilibrium conditions, the composite fiber composite relation is determined. The effect of separation is assumed by introducing tangential and normal scalar parameters in the equations by assuming the displacement field jump at the common boundary. In order to express the effect of matrix micro-cracks, the fracture mechanics framework of continuous environments was used and the micro-cracks parallel to the fibers, perpendicular to the fibers and in the thickness direction with scalar parameters were expressed. At the end of the effect of these parameters the results are presented in graphs. The results show that the presence of defective joint at the joint boundary and the matrix micro-components reduce the hardness of the composite and thus it’s bearing load, which is more significant at the defective joint state.

Biodegradable poly(ɛ-caprolactone) (PCL) and its composites or blends have gotten a lot of attention in the last decade because of their potential applications in human life and environmental remediation. As a result, there is a growing interest in the synthesis of PCL-composites/blends and their applications. Greater efforts have been made to develop biodegradable chemical materials as adsorbents that do not pollute the environment in order to replace traditional materials. Among the numerous types of degradable materials, PCL is currently the most promising, the most popular, and the best material to be developed, and it is referred to as the "green" eco-friendly material. Membranes and adsorbents for water treatment, packaging and compost bags, controlled drug carriers, biomaterials for tissues such as bone, cartilage, ligament, skeletal muscle, skin, cardiovascular and nerve tissues are just some of the applications of this biodegradable polymer (PCL). The goal of this review is to present a brief overview of PCL, its properties, syntheses of PCL, PCL composites, and PCL blends, but to provide a detailed investigation into the utility of PCL/PCL-based adsorbing agents in the removal of dyes/heavy metal ions.

This paper addresses a new micromechanical model to predict biaxial tensile moduli of plain weave fabric (PWF) composites by considering the interaction between the orthogonal interlacing strands. The two orthogonal yarns in micromechanical unit cell (UC) were idealized as the curved beams with a path depicted by using sinusoidal shape functions. The biaxial tensile moduli of PWF composites were derived by means of the minimum total complementary potential energy principle founded on micromechanics. The biaxial tensile tests were respectively conducted on the RTM-made EW220/5284 PWF composites at five biaxial loading ratios of 0, 1, 2, 3 and ∞ to validate the new model. The predictions from the new model were compared with experimental data and good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed model. Using the new model, the biaxial tensile moduli of plain weave fabric (PWF) composites could be predicted based only on the properties of basic woven fabric.

Thermoplastic pultrusion is a suitable process for fabricating continuous unidirectional thermoplastics with a uniform cross-section, high mechanical properties due to continuous fiber reinforcement, low cost, and suitability for mass production. In this paper, jute and glass fibers were reinforced with a polypropylene matrix and fabricated using the thermoplastic pultrusion process. The volumetric fraction of the composite was designed by controlling the filling ratio of the reinforcing fiber and matrix. The effects of molding parameters were investigated, such as pulling speed and molding temperature, on the mechanical properties and microstructure of the final rectangular profile composite. The pulling speed and molding temperature were varied from 40 to 140 mm/min and 190 to 220°C, respectively. The results show that an increase in molding temperature initially led to an increase in mechanical properties, up to a certain point. Beyond that point, they started to decrease. The increase in molding temperature also led to an increase in void content. Meanwhile, un-impregnation decreased with the increase in molding temperature, and the jute fiber began to degrade at high temperatures. In the next step, with varying pulling speed, the mechanical properties decreased as the pulling speed increased, with a corresponding increase in void content and un-impregnation. The decrease in mechanical properties was influenced by the increase in void content and un-impregnation, as the jute fiber degraded at higher temperatures.

Tooth decay, also known as caries, is a significant medical problem that harms teeth. Treatment is based on the removal of the carious material and then filling the cavity left in the tooth, most commonly with amalgam or composite resin. The consequences of filling failure include repeating the filling, or performing another treatment, such as a root canal, or extraction. Dental amalgam contains mercury, and there is a global effort to reduce its use. However, no consensus has been reached using randomized clinical trials, regarding whether amalgam or composite resin materials are more durable, and which is the best restorative material. To determine which material is superior, we performed a retrospective cohort study using a large database where members of the 58 dental clinics with 440 dental units were treated. The number of failures of the amalgam compared to composite resin restorations between 2014 and 2021 were compared. Our data included information from over 650,000 patients. Between 2014 - 2021, 260,905 patients were treated. 19,692 out of 113,281 first amalgam restorations failed (17.49%), whereas significantly fewer composite restorations failed (11.98%) 65,943 out of 555,671. This study indicates that composite is superior to amalgam and therefore it is reasonable to cease using mercury containing amalgam.

A multiscale modelling approach was developed in order to estimate the effect of defects on the strength of unidirectional carbon fiber composites. The work encompasses a micromechanics approach, where the known reinforcement and matrix properties are experimentally verified and a 3D finite element model is meshed directly from micrographs. Boundary conditions for loading the micromechanical model are derived from macroscale finite element simulations of the component in question. Using a microscale model based on the actual microstructure, material parameters and load case allows realistic estimation of the effect of a defect. The modelling approach was tested with a unidirectional carbon fiber composite beam, from which the micromechanical model was created and experimentally validated. The effect of porosity was simulated using a resin-rich area in the microstructure and the results were compared to experimental work on samples containing pores.

The aim of this paper is to establish a valid procedure for better understanding all the phenomena associated with the high-speed machining of Glass Fibre Reinforced Plastic (GFRP) composites. Both rectangular and circular specimens were machined at high speeds (up to 50 m/min) in order to understand what occurred for all values of fiber orientation angles during machining operations. An innovative testing methodology was proposed and studied to investigate the phenomenon of burr formation and thus understand how to avoid it during machining operations. To this end, the forces arising during the machining process and the roughness of the resulting surface, were carefully studied and correlated with the cutting angle. Additionally, the cutting surface and chip morphology formed during cutting tests were examined using a high-speed camera. Close correlations are found between the variations of the cutting forces' signals and the trends of the roughness and the morphology of the machined surface.

Antimicrobial peptides (AMPs) have emerged as a promising class of bioactive molecules with the potential to combat infections associated with medical implants and biomaterials. This review article aims to provide a comprehensive analysis of the role of antimicrobial peptides in medical implants and biomaterials, along with their diverse clinical applications. The incorporation of AMPs into various medical implants and biomaterials has shown immense potential in mitigating biofilm formation and preventing implant-related infections. We review the latest advancements in biomedical sciences and discuss the AMPs that were immobilized successfully to enhance their efficacy and stability within the implant environment. We also highlight successful examples of AMP coatings for the treatment of surgical site infections (SSIs), Contact lenses, Dental Applications, AMP-Incorporated Bone Grafts, Urinary tract infections (UTIs), Medical Implants, etc. Additionally, we discuss the potential challenges and prospects of AMPs in medical implants, such as effectiveness, instability and implant-related complications. We also discuss strategies that can be employed to overcome the limitations of AMP-coated biomaterials for prolonged longevity in clinical settings.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

Novel bio-inspired materials have gained recently great attention, especially in medical applications. Applying sophisticated design and engineering methods, various polymer-polymer hybrid systems with outstanding performance have been developed in last decades. Hybrid systems composed of bioelastomers and hydrogels are very attractive due to their high biocompatibility and elastic nature for advanced biomaterials used in various medical applications such as drug delivery systems and scaffolds for tissue engineering. Herein, we describe the advances in current state-of-the-art design, properties and applications of polymer-polymer hybrid systems in medical applications. Bio-inspired functionalities, including bioadhesiveness, injectability, antibacterial properties and degradability applicable to advanced drug delivery systems and medical devices will be discussed in a context of future efforts towards development of bioinspired materials.

The formation of a rigid tough interface based on a nacre-like structure in carbon fiber (CF) composites is a promising way to eliminate low delamination resistance. An effective method of coating CFs is electrophoretic deposition (EPD), which, in the case of dissimilar components like graphene oxide (GO) and polymeric glue, usually requires their chemical bonding/ strong interactions. In this work, we focus on chitin nanocrystals (ChNCs), leading to an excellent mechanical performance of artificial nacre, where favorable interactions and bonding with GO were controlled by degrees of deacetylation (5, 15 and 30 %). We have prepared coatings based on GO/ChNCs adducts with 95/5, 90/10,50/50 and 25/75 ratios using optimized EPD conditions (pH, concentration, voltage and time). The prepared materials were characterized using FTIR, TEM, XPS, SEM, DLS, and XRD. SEM evaluation indicates the formation of a homogeneous interlayer, which possesses a fair ability of chemical bonding with the epoxy matrix. Short beam testing of epoxy matrix composites indicates that coating does not decrease stiffness and its relatively low dependence on composition. Therefore, all coatings are promising for a detailed study of delamination resistance using laminate samples. Moreover, facile EPD from water solution/ suspension has a fair potential for industrial applications.

This article introduces a novel nature-inspired metaheuristic algorithm called Frilled Lizard Optimization (FLO), which emulates the hunting behavior of frilled lizards in their natural habitat. FLO draws in-spiration from the sit-and-wait strategy observed in frilled lizards during hunting. The underlying theory of FLO is presented and mathematically formulated in two phases: (i) an exploration phase, simulating the frilled lizard's attack towards prey, and (ii) an exploitation phase, simulating the lizard's retreat to the top of the tree after feeding. To assess FLO's efficacy in solving optimization problems, the algorithm's performance is evaluated across fifty-two standard benchmark functions, encompassing unimodal, high-dimensional multimodal, fixed-dimensional multimodal, and the CEC 2017 test suite. Comparative analyses with twelve existing metaheuristic algorithms are conducted. The simulation results reveal that FLO, distinguished by its adeptness in exploration, exploitation, and balancing them during search process, outperforms competing algorithms. Additionally, FLO is implemented on twenty-two constrained optimization problems from the CEC 2011 test suite and four engineering design problems, demonstrating its effectiveness in addressing real-world optimization applications.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

Defectively manufactured and deliberately damaged composite laminates fabricated with different continuous reinforcing fibres (respectively, carbon and glass) and polymer matrices (respectively, thermoset and thermoplastic) were inspected in magnetic resonance imaging equipment. Two pulse sequences were evaluated during non-destructive examination conducted in saline solution-immersed samples to simulate load-bearing orthopaedic implants permanently in contact with biofluids. The orientation, positioning, shape, and especially the size of translaminar and delamination fractures were determined according to stringent structural assessment criteria. The spatial distribution, shape, and contours of water-filled voids were sufficiently delineated to infer the amount of absorbed water if thinner image slices than this study were used. The surface texture of composite specimens featuring roughness, waviness, indentation, crushing, and scratches was outlined, with fortuitous artefacts not impairing the image quality and interpretation. Low electromagnetic shielding glass fibres delivered the highest, while electrically conductive carbon fibres produced the poorest quality images, particularly when blended with thermoplastic polymer, though reliable image interpretation was still attainable.

This paper delves into the application of digital twin monitoring techniques for enhancing offshore floating wind turbine performance, with a detailed case study. We explore the practical implementation of digital twins and their efficacy in optimizing operations and predictive maintenance. Our findings emphasize digital twins' potential as a valuable tool for renewable energy, driving efficiency and sustainability in offshore floating wind installations.

Among the various methods for collecting oil spills and oil products, including from the water surface, one of the most effective is the use of sorbents. In this work, three-component bio-based composite granular adsorbents were produced and studied for oil products pollution collection. A bio-based binder made of peat, devulcanised crumb rubber from used tyres, and part fly ash as cenospheres were used for absorbent production. The structure, surface morphology, porosity, mechanical properties, and sorption kinetics of the obtained samples were studied. Composite hydrophobicity and sorption capacity to oil products such as diesel fuel (DF) and motor oil (MO) were determined. The obtained pellets are characterised by a sufficiently pronounced ability to absorb oil products such as DF. As the amount of CR in the granules increases, the diesel absorption capacity increases significantly. The case of 30-70-0 is almost 3 times higher than the granules from homogenised peat. The increase in q is due to two factors: pronounced surface hydrophobicity of the samples (Θ = 152°) and a heterogeneous porous granule structure. The presence of the cenosphere in the biocomposite reduces its surface hydrophobicity while increasing the diesel absorption capacity. Relatively rapid realisation of the maximum saturation by the MO was noted. In common, the designed absorbent shows up to 0.7 g·g^-1 sorption capacity for MO and up to 1.55 g·g^-1 sorption capacity for diesel. A possible mechanism of DF absorption and the limiting stages of the process approximated for different kinetic models are discussed. The Weber-Morris diffusion model is used to primarily distinguish the limiting effect of external and internal diffusion of adsorbate on the absorption process

This paper deals with analyzing the structural responses of glass-fiber-reinforced polymer (GFRP) tubes filled with recycled and concrete material for developing composite piles, as an alternative to traditional steel reinforced piles in bridge foundations. The Full-scale GFRP composite piles included three inner and outer layers, using a fiber-oriented material that was inclined longitudinally, almost 40 degrees from the horizontal axis of the pile. The segment between these two layers was inclined 80 degrees from the longitudinal axis of the tube. The behavior of the filled GFRP tubes was semi-linear, and resulted in increasing the total ductility and strength of the piles. Adjusting the material’s properties, such as the EAxial, EHoop, and Poisson ratios optimized the results. The lateral strength of the GFRP composite pile and pre-stressed piles are comparable in both axial and lateral loading conditions.

Wood plastic composite usage and demands have increased due to chemical, and mechanical properties when compared to plastic materials. However, because of the possibility of structural and mechanical changes of the material when exposed to external environment more research needs to be done. In the present study yellow birch/HDPE composites materials made by injection molding were treated by zinc oxide and exposed to fungal rots. Mechanical properties of the composites were assessed by Tensile and Izod impact test. The impact energies of the samples loaded with 30 % ZnO-treated fibers and exposed to G. trabeum and T. versicolor decreased, compared to when samples were not treated with ZnO. The mechanical properties of all samples treated with ZnO and exposed to rot decreased which were reported as a decreased Young's modulus and impact energies. ZnO prevented mycelium proliferation which was nonexistent on samples. It has been noted that the decrease in mechanical properties of treated samples was due to NaOH used to dissolve the ZnO powder.

For the numerical simulation of components made of short fiber-reinforced composites the correct prediction of the deformation including the elastic and plastic behavior and its spatial distribution is essential. When using purely deterministic modeling approaches the information of the probabilistic microstructure is not included in the simulation process. One possible approach for the integration of stochastic information is the use of random fields. In this study numerical simulations of tensile test specimens are conducted utilizing a finite deformation elastic-ideal plastic material model. A selection of the material parameters covering the elastic and plastic domain are represented by cross-correlated second-order Gaussian random fields to incorporate the probabilistic nature of the material parameters. To validate the modeling approach tensile tests until failure are carried out experimentally, that confirm the assumption of spatially distributed material behavior in both the elastic and plastic domain. Since the correlation lengths of the random fields cannot be determined by pure analytic treatments, additionally numerical simulations are performed for different values of the correlation length. The numerical simulations endorse the influence of the correlation length on the overall behavior. For a correlation length of 5mm a good conformity with the experimental results is obtained. Therefore, it is concluded, that the presented modeling approach is suitable to predict the elastic and plastic deformation of a set of tensile test specimens made of short fiber-reinforced composite sufficiently.

Rigid-hulled inflatable boats are extremely practical and popular nowadays. They offer a effective conciliation among usability and costs. Their stable and seaworthy behaviour is guaranteed by performing hydroplaning hulls coupled with unsinkable inflated tubes. At the same time, their design is often based on tradition and preconceptions. Rarely, the design assumptions are validated by the reality or, even, by deeper investigations. In this article, both numerical methods and experimental mechanics techniques are proposed as an essential way for supporting the designers in their decisive tasks. Three different situations are detailed where a numerical or an experimental approach shows its benefit inside the engineering design process: firstly permitting to investigate the behaviour of materials driving the fiberglass selection; then measuring the levels of stress and strain in the hull during sailing; finally, using all available information as a base for developing numerical models of the hull slamming in waves. Even if the discussion is focused on a rigid inflatable boat, large part of its considerations is relevant beyond this special case.

Background: Advances in additive manufacturing and the development of antimicrobial biopolymers facilitate the production of critical medical devices with strong and safe biocidal properties. The purpose of this study was to assess the antimicrobial efficacy, safety, and longevity of a polylactic acid-based biopolymer supplemented with a copper-based composite additive. Methods: An antimicrobial polylactic acid-based biopolymer was tested against several inoculants including Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Material safety was evaluated according to international testing standards for in vitro cytotoxicity. Results: The main findings of the present investigation showed a strong and long-lasting biocidal effect of a polylactic acid-based biopolymer embedded with a copper-based composite additive against Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Furthermore, the cytotoxicity and safety assessment of the antimicrobial biopolymer was found to be “non-toxic” and safe for human skin contact. Conclusions: The present investigation showed that the antimicrobial biopolymer exhibits strong and long-lasting biocidal properties against an array of viral and bacterial inoculants.

Multilayered metallic sheets fabricated by hot metal forming processes are attractive structural components in the aerospace and automobile industry. The strength of the mechanical bond between the different layers is critical to the applicability of such components in load bearing applications. While it is well understood that the process conditions such as temperature, deformation and rate of deformation influence the bond strength, a clear functional relationship between these conditions and the bond strength has yet to be established. The objective of the current study is to investigate the joining of Aluminum-6061 alloy specimens by hot compression bonding. Hot compression tests of beam specimen pairs were conducted at different temperatures (300-500℃), with different strains and strain rates (10-2-10-1 [1sec]). Coupled thermo-mechanical finite element models were utilized to compute the time dependent thermo-mechanical fields that develop along the specimen interface. The computed values were used to map the spatial distribution of a scalar parameter J which is hypothesized to govern bond formation. Mechanical tensile tests were used to determine the bond strength and expose the bonded surfaces. It is demonstrated that the computed J distribution can be correlated well with SEM observations of the debonded surface. It is also shown that the actual bonded area can be predicted from the computations for a certain range of critical J values.

Green synthesis offers a superior alternative to traditional methods for producing metal and metal oxide nanoparticles. This approach is not only benign and safe but also cost-effective, scalable, and straightforward, operating under ambient conditions. Notable metals and metal oxide nanoparticles, such as manganese oxides, iron oxides, silver, and gold, have been produced using various bio-reductants derived from plant extracts. These biological agents not only expedite the reduction process but also stabilize the nanoparticles, serving dual roles as reducing and capping agents. This review presents the green synthesis of nanoparticles (NPs) obtained from biogenic wastes and plant extracts. The green-synthesized nanostructured MnO2 are evaluated as a potential photocatalyst for water treatment and as an electrode material in lithium-ion batteries and supercapacitors. The green-derived iron oxide nanoparticles are examined as promising antioxidant, anti-inflammatory, and anti-diabetic agents. Additionally, this review discusses the green synthesis of precious metal nanoparticles, specifically silver (Ag NPs) and gold (Au NPs), highlighting their potential medical applications in areas like antiviral treatments and cancer therapy.

In the present study, hypereutectic Al-Si alloy compacts and Al-Si/B4C composites were produced by conventional, microwave and spark plasma sintering techniques. The effects of sintering techniques and B4C particle addition on microstructural properties, density, hardness and electrical conductivity were investigated. The microstructures were examined with an optical microscope. Densities were measured using the Archimedes technique. Electrical resistance measurements were made with the four-point probe measurement technique. Elemental Al grains, master alloy grains and primary Si particles were determined in the microstructures of all samples. The addition of 15 wt% B4C caused the porosity rate to increase in the samples. Samples produced with SPS technique gave ≈80% higher hardness values than samples produced with CS and MWS. Compared to the samples produced with CS and MWS, the samples produced with SPS gave higher electrical conductivity values. Electrical conductivities were decreased as the weight percentage of B4C increased in all samples.

The interlaminar shear behavior of a [±45°] laminated carbon fiber reinforced plastic (CFRP) specimen was investigated utilizing microscale strain mapping in a wide field of view. A three-point bending device was developed under a laser scanning microscope, and the full-field strain distributions including normal, shear and principal strains of CFRP in a three-point bending test were measured using a developed sampling Moire technique. The microscale shear strain concentrations at interfaces between each two adjacent layers were successfully detected and found to be positive-negative alternately distributed before damage occurrence. The 45° layers slipped to the right relative to the -45° layers, visualized from the revised Moire phases and shear strain distributions of the angle-ply CFRP under different loads. The absolute values of the shear strain at interfaces gradually rose with the increase of the bending load, and the sudden decrease of the shear strain peak value implied the occurrence of interlaminar damage. The evolution of the shear strain concentrations is useful in the quantitative evaluation of the potential interlaminar shear failure.

Electronic devices are sensitive to electromagnetic (EM) emissions requiring electromagnetic shielding protection to assure good operation, preventing noise, malfunctioning, or even burning. To assure protection, it is important to develop suitable material and design solutions for electronic enclosures. Most common enclosures are made with metal alloys by traditional manufacturing methods. However, resourcing to thermoplastic composites combined with additive manufac-turing (AM) technologies emerges as an alternative that enables to fabricate complex parts that are lightweight, consolidated and oxidation and corrosion resistant. In this research, an AM technique based in material extrusion was used to print 2 mm thick specimens with a multi-material made of micro-carbon fiber (CF) filled polyamide, reinforced, at specific layers, by continuous carbon fibers stacked with a 90° rotation to each other. Specimens electromagnetic shielding effectiveness (EMSE) was evaluated in the frequency band of 0.03 – 3 GHz by coaxial transmission line method. De-pending on the number of CF layers, the EM shielding obtained can up to 70 dB, with a specific shielding up to 60 dB.cm3/g, predominantly by absorption mechanism, being 22 times higher that without the CF layers. These findings fundament this innovative approach for lightweight cus-tomizable solutions for EM shielding applications.

Machine learning (ML) is penetrating in all walks of life and is one of the major driving forces behind the fourth industrial revolution, typically known as Industry 4.0. This study reviews the state-of-the-art ML applications in the biofuels’ life cycle stages, i.e., soil, feedstock, production, consumption, and emissions. A keyword search is performed to retrieve relevant articles from the databases of the Web of Science and Google Scholar. ML applications in the soil stage were mostly based on the use of satellite images of land for estimation of biofuels yield or suitability analysis of agricultural land. In the second stage of the life cycle, assessment of rheological properties of the feedstocks and their effect on the quality of biofuels were dominant studies reported in the literature. The production stage included estimation and optimization of quality, quantity, and process conditions. The fuel consumption and emissions stage included analysis of engine performance and estimation of emissions temperature and composition, such as NOx, CO, and CO2. This study identified the following trends: dominant ML method, the stage of life cycle getting more usage of ML, the type of data used for the development of the ML-based models, and the stage-wise frequently used input and output variables. The findings of this article are beneficial for academia and industry-related people involved in model development in different stages of biofuel’s life cycle.

Machine learning (ML) is penetrating in all walks of life and is one of the major driving forces behind the fourth industrial revolution, typically known as Industry 4.0. The purpose of the present study is to review the state-of-the-art ML applications in the biofuels' life cycle stages, i.e., soil, feedstock, production, consumption, and emissions. A keyword search is performed to retrieve relevant articles from the databases of the Web of Science and Google Scholar. ML applications in the soil stage were mostly based on the use of satellite images of land for estimation of biofuels yield or suitability analysis of agricultural land. In the second stage of the life cycle, assessment of rheological properties of the feedstocks and their effect on the quality of biofuels were dominant studies reported in the literature. The production stage included estimation and optimization of quality, quantity, and process conditions. The fuel consumption and emissions stage included analysis of engine performance and estimation of emissions temperature and composition, such as NOx CO, and CO2. This study identified the following trends: dominant ML method, the stage of life cycle getting more usage of ML, the type of data used for the development of the ML-based models, and the stage-wise frequently used input and output variables. The findings of this article are beneficial for academia and industry-related people involved in model development in different stages of biofuel’s life cycle.

The development of hybrid rockets offers excellent opportunities for the practical education of students at universities due to a high safety and a relatively low complexity of the rocket propulsion system. During the German educational program STERN, students of the Technische Universität Braunschweig obtain the possibility to design and launch a sounding rocket with a hybrid engine. The design of engine HYDRA 4X is presented and results of first engine tests are discussed. Results for measured regression rates are compared to results from literature. Furthermore, the impact of the lightweight casing material CFRP on the hybrid engine mass and flight apogee altitude is examined for rockets with different total impulse classes (10 to 50 kNs). It is shown that the benefit of a lightweight casing material on engine mass decreases with an increasing total impulse. However, a higher gain on apogee altitude, especially for bigger rockets with a comparable high total impulse is shown.

The well-being and sociability of individuals have always been part of modernity. The development of new technologies that meet these aspirations is receiving increasing attention. Thus, strengthening the desired objectives of these tools and minimizing their undesirable side effects is the subject of a growing commitment. The present contribution aims, in this context, to evaluate and analyze the desired and undesirable effects of the interaction of electromagnetic fields with living tissues in general. This involves routines reinforcing expected functions as well as those controlling and protecting against undesirable effects. First, the interactions of electromagnetic fields with tissues are analyzed, involving their thermal biological effects of desired and undesired exposures. The roles of blood and sap fluids in bio-affected tissues are then analyzed. Secondly, the governing electromagnetic, bio-heat equations, and their coupled solution are studied. Third, the thermal behavior of tissues and the exposure adverse effects are examined. Next, monitoring and defending of the effects of exposures are discussed. This contribution illustrates and discusses mathematical modeling routines based on a generalized interaction of electromagnetic fields with living tissues.

Promoter is a small region of DNA sequence in response to various transcription factors, which initiates a particular gene expression. The promoter-engineered bio-sensor can activate or repress gene expression through transcription factor recognizing specific molecules, such as polyamine, sugars, lactams, amino acids, organic acids or redox molecule, however, the reported applications of promoter enhanced bio-sensor are not too much. This review paper highlights the strategies of construction of promoter-gene engineered bio-sensor with human and bacteria’s genetic promoter array for high-throughput screening (HTS) molecular drugs, study of membrane protein’s localization and nucleocytoplasmic shuttling mechanism of regulating factor, enzyme activity, detection of the toxicity of intermediate chemicals, and probing bacteria density to improve value-added product titer. These bio-sensors’s sensitivity and specificity can be further improved by proposed approaches of Mn²⁺ and Mg²⁺ added random Error-prone PCR and site-directed mutagenesis which is applied for construction of bacteria’s “mutant library”. It is expected to establish flexible HTS platform (Bio-sensor array) to large-scale screen transcription factor-acting drugs, reducing the toxicity of intermediate compounds, and constructing gene dynamic regulatory system in “push and pull” mode to effectively regulate the valuable medicinal product production. This proposed novel promoter-engineered biosensors aided synthetic genetic circuit construction will maximize the efficiency of bio-synthesis of medicinal compound, which will greatly promote the development of microbial metabolic engineering and biomedical science.

The pervasive presence of atmospheric pollution, particularly polycyclic aromatic hydrocarbons such as 7,12-dimethylbenz(a)anthracene, instigates aberrant cellular and tissue conditions, precipitating oxidative damage and inflammatory cascades conducive to the onset of cancer, notably mammary cancer. Given the hepatic metabolism of 7,12-dimethylbenz(a)anthracene, the imperative of employing natural antioxidants becomes apparent. In this study, we delve into the antioxidant and hepato-protective properties of Pistacia lentiscus against 7,12-dimethylbenz(a)anthracene-induced toxicity, alongside exploring its potential anticancer attributes. Our investigations unveil Pistacia lentiscus's anti-proliferative efficacy against human breast cancer cell lines. Notably, 7,12-dimethylbenz(a)anthracene-intoxication escalates body weight, disrupts lipid profiles, and incites serum oxidative damage. Concurrently, hepatic and renal oxidative stress ensue, accompanied by heightened antioxidant enzyme activity in the 7,12-dimethylbenz(a)anthracene-exposed-group compared to controls (p&lt;0.05). Nonetheless, Pistacia lentiscus co-administration rectifies biochemical imbalances, significantly attenuates oxidative stress aberrations, and augments antioxidant enzyme responses (p&lt;0.05). Importantly, histological analysis evinces Pistacia lentiscus's shielding effect against 7,12-dimethylbenz(a)anthracene induced hepatocyte injury and steatosis. Our findings underscore Pistacia lentiscus's robust anti-proliferative, antioxidant, and hepato-protective capacities, mitigating metabolic disturbances, oxidative stress propagation in liver and kidney functions, and potential histological alterations, thereby impeding 7,12-dimethylbenz(a)anthracene-induced mammary cancer initiation. We posit that Pistacia lentiscus may serve as a prophylactic agent against breast cancer instigated by this carcinogen.

In this study is reported the optical, structural and dielectric properties of Poly (vinyl alcohol) thin films membranes with embedded ZnO nanoparticles (PVA/ZnO) obtained by solution casting method at low temperature of deposition. Fourier Transform Infrared spectra showed the characteristics peaks, which correspond to O-H and Zn-O bonds present in the hybrid material. The X-ray diffraction patterns indicated the presence of ZnO structure into the films. The composite material showed low absorbance and a wide band gap energy from 5.6 to 5.9 eV. The surface morphology for the thin films of PVA/ZnO was studied by Atomic Force Microscopy and Scanning Electron Microscopy. The dielectric properties of the nanocomposites were measured from low to high frequencies, the results showed a high dielectric constant (ε) in the order of 10⁴ at low frequency and values from ε ≈ 2000 to 100 in the range of 1KHz-1MHz respectively, the properties of PVA/ZnO such as the high permittivity and the low temperature of processing make it a suitable material for potential applications in the development of flexible electronic devices.

Diagnosis and prognosis of failures for aircrafts’ integrity are some of the most important regular functionalities in complex and safety-critical aircraft structures. Further, development of failure diagnostic tools such as Non-Destructive Testing (NDT) techniques, in particular, for aircraft composite materials, has been seen as a subject of intensive research over the last decades. The need for diagnostic and prognostic tools for composite materials in aircraft applications rises and draws increasing attention. Yet, there is still an ongoing need for developing new failure diagnostic tools to respond to the rapid industrial development and complex machine design. Such tools will ease the early detection and isolation of developing defects and the prediction of damages propagation; thus allowing for early implementation of preventive maintenance and serve as a countermeasure to the potential of catastrophic failure. In this paper, following a short introductory summary and definitions, this paper provides a brief literature review of recent research on failure diagnosis of composite materials with an emphasis on the use of NDT techniques in aerospace industry. In addition to this, within a some of significant NDT application extents, prognosis of composites is also briefly discussed.

Nowadays asymmetric thin film composite (TFC) polymeric hollow fiber (HF) membranes are extensively used in industrial gas/vapor separations, water treatment etc. There are numerous advantages to use hollow fibers such as: low energy requirements, simplicity of operation, and high specificity. In the present article we discuss the progress made during the past decade in the preparation of the HF substrate and preparation/modification of the thin selective layer. Their applications in water treatment, dehydration of alcohols via pervaporation and gas/vapor separation are also demonstrated.

Efficient use of agricultural wastes and by-products, basically transforming waste materials into value added products, is considered as pivotal for an effective bioeconomy strategy for the rural development. To this scope, citrus waste management represents a major issue for citrus processors but, at the same time, it embodies a potentially unexploited resource for the rural sustainable development. This study focuses on analyzing the current management of citrus waste in South Italy and identifying the determinants and barriers that may affect an entrepreneur’s choice on the destination of citrus waste. Citrus processors’ preferences about the contract characteristics needed to take part in a co-investment scheme have been investigated. Both analyses are preliminary steps to design an innovative and sustainable citrus by-product supply chain. Results show that the distance between the citrus processors and the citrus by-products plant is one of the main criteria for choosing alternative valorization pathways. Moreover, the required guaranteed capital, the short duration of the contract, and low risk are contract scheme characteristics that improve entrepreneurs’ willingness to co-invest in the development of a citrus waste multifunctional plant.

Surface initiated atom transfer radical polymerization (SI-ATRP) is one of the most versatile technique to modify the surface properties of material. Recent developed metal free SI-ATRP makes such technique more widely applicable. Herein photo-induced metal-free SI-ATRP of methacrylates, such as methyl methacrylate, N-isopropanyl acrylamide, and N,N- dimethylaminoethyl methacrylate, on the surface of SBA-15 was reported to fabricate organic-inorganic hybrid materials. SBA-15 based polymeric composite with adjustable graft ratio was obtained. The structure evolution during the SI-ATRP modification of SBA-15 was monitored and verified by FT-IR, XPS, TGA, BET, and TEM. The obtained polymeric composite showed enhanced adsorption ability for the model compound toluene in aqueous. This procedure provides a low cost, ready availability, and facile modification way to synthesize the polymeric composites without the contamination of metal.

We use COMSOL Multiphysics software to model optical processes in media and the effects of light propagation in whispering gallery mode resonators (WGMRs). Although plane wave irradiating on resonator does not create resonances, it was shown that they can be obtained when focused tangentially on the perimeter of the resonator. We demonstrate that resonances can be excited in resonators by prism coupling when the incident angle of the light is larger than the angle of total internal reflection. We determined the optimal distance between the prism and the resonator to get the strongest resonances. Bio-sensing principle of WGMRs is shown by demonstrating that the shift of resonances increases with a larger number of "bio-molecules" attached to the surface of WGMR. Surface functionalization and surface roughness were explored.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

Alzheimer's disease (AD) is a significant regular type of dementia that causes damage in brain cells. Early detection of AD acting as an essential role in global health care due to misdiagnosis and sharing many clinical sets with other types of dementia, and costly monitoring the progression of the disease over time by magnetic reasoning imaging (MRI) with consideration of human error in manual reading. Our proposed model, in the first stage, apply the medical dataset to a composite hybrid feature selection (CHFS) to extract new features for select the best features to improve the performance of the classification process due to eliminating obscures features. In the second stage, we applied a dataset to a stacked hybrid classification system to combine Jrip and random forest classifiers with six model evaluations as meta-classifier individually to improve the prediction of clinical diagnosis. All experiments conducted on a laptop with an Intel Core i7- 8750H CPU at 2.2 GHz and 16 G of ram running on windows 10 (64 bits). The dataset evaluated using an explorer set of weka data mining software for the analysis purpose. The experimental show that the proposed model of ‏(CHFS) feature extraction ‏performs better than principal component analysis (PCA), and lead to effectively reduced the false-negative rate with a relatively high overall accuracy with support vector machine (SVM) as meta-classifier of 96.50% compared to 68.83% which is considerably better than the previous state-of-the-art result. The receiver operating characteristic (ROC) curve was equal to 95.5%. Also, the experiment on MRI images Kaggle dataset of CNN classification process with 80.21% accuracy result. The results of the proposed model show an accurate classify Alzheimer's clinical samples against MRI neuroimaging for diagnoses AD at a low cost.

This work aims to investigate the effect of process temperature and catalyst content by thermochemical degradation of municipal solid waste (MSW) fraction (organic matter + paper + plastic) on the yield of reaction products (bio-oil, biochar, H2O and gas), physicochemical properties and chemical composition of bio-oils, as well as on the morphology and crystalline phases of biochar in laboratory scale. The organic matter, paper and plastic segregated from the gravimetric composition of total waste sample were subjected to the pre-treatments of drying, crushing and sieving. The experiments were carried out at 400, 450 and 475 °C and 1.0 atmosphere, and at 450 °C and 1.0 at-mosphere, using 5.0, 10.0 and 15.0% (wt.) of FCC zeolite, bath mode, using a laborato-ry scale glass reactor. The bio-oil was characterized for acidic value. The chemical functions present in the bio-oil identified by FT-IR and the composition by GC-MS. Biochar was characterized by SEM/EDS and XRD. Thermal pyrolysis of the MSW frac-tion (organic matter + paper + plastic) shows bio-oil yields between 9.44 and 9.24% (wt.), aqueous phase yields between 21.93 and 18.78% (wt.), solid phase yields between 67.97 and 40.34% (wt.) and gas yields between 28.27 and 5.92% (wt.). The yield of bio-oil decreases with increasing process temperature. For the experiments using FCC, the biochar and gas yields increase slightly with the FCC content, while that of bio-oil de-creases and the H2O phase remains constant. The GC-MS of bio-oils identified the presence of hydrocarbons and oxygenates, as well as nitrogen-containing compounds, including amides and amines. The acidity of the bio-oil increased with increasing temperature and with the aid of FCC as a catalyst. It has been identified the presence of hydrocarbons within bio-oil by addition of FCC catalyst due to the deoxygenation of carboxylic acids, followed by decarboxylation and decarbonylation reactions, producing aliphatic and aromatic hy-drocarbons.

Hansenula polymorpha is a non-conventional, methylotrophic, and thermo-tolerant yeast well known for the industrial production of recombinant proteins. However, the research to evaluate this yeast potential for sugar fermentation to produce alcohols for biofuel applications is at an infant stage. For research advancement, the present work investigated the wild type H. polymorpha strain (DSM 70277) for the co-production of methanol, ethanol, and butanol using a batch fermentation reactor and performing experiments at an ideal temperature of 40°C with a pH of 5.5 using different sugars (fructose, glucose, and xylose) as substrates. The maximum specific growth rates (h-1) of H. polymorpha yeast were 0.59–3.02 for fructose, 0.08–2.60 for glucose, and 0.06–0.08 for xylose. The overall yields (g/g) of methanol were higher from fructose (0.132–0.226) than glucose (0.020–0.021) and xylose (0.009–0.030). Ethanol overall yield (g/g) from fructose (0.130–0.325) was more than glucose (0.054–0.167), and xylose (0.042–0.068). The overall butanol yield (g/g) ranged from 0.018–0.031 (fructose), 0.017 (glucose), and 0.009–0.010 (xylose). Due to the methylotrophic nature of H. polymorpha, a shorter time (preferably 2 h) was found suitable for co-production of methanol, ethanol, and butanol.

The bio-oil obtained by pyrolysis of Açaí (Euterpe oleracea Mart.) seeds at 450 ºC, 1.0 atmosphere, in technical scale, submitted to fractional distillation to produce biofuels-like fractions. The distillation of bio-oil carried out in a laboratory distillation column (Vigreux) of 30 cm. The physical-chemistry properties (density, kinematic viscosity, acid value and refractive index) determined by official methods. The chemical functions present in distillation fractions determined by FT-IR and the chemical composition by GC-MS. The distillation of bio-oil yielded gasoline, light kerosene, and kerosene-like fuel fractions of 16.16, 19.56, and 41.89% (wt.), respectively. All the physical-chemistry properties (density, kinematic viscosity, acid value and refractive index) increase with boiling temperature. The gasoline-like fraction is composed by 64.0% (area.) hydrocarbons and 36.0% (area.) oxygenates, while light kerosene-like fraction by 66.67% (area.) hydrocarbons and 33.33% (area.) oxygenates, and kerosene-like fraction by 19.87% (area.) hydrocarbons and 81.13% (area.) oxygenates.

In this work, three different types of sandwich structures were manufactured using Formica sheet (a paper-based sheet) as skin and perlite/sodium silicate foam as core with/without the paper honeycomb. The sandwich structures were fabricated by attaching Formica sheets on both sides of the honeycomb, perlite/sodium silicate foam, and perlite/sodium silicate foam-filled honeycomb core panels. The flexural characteristics were studied by a three-point bending test and the thermal conductivity was measured using Lee’s thermal conductivity apparatus. The results demonstrated a significant improvement in flexural properties, including core shear stress, facing stress, bending stress, and energy absorption, when incorporating the paper honeycomb reinforcement. The thermal conductivity and flexural properties were found to be well-compatible with the existing building materials for similar applications in the literature. The failure investigation revealed that the sandwiches with paper honeycomb only prematurely failed due to core buckling, whereas the foam-filled honeycomb core-based sandwiches were able to sustain higher loads, exhibiting material failures such as core shear failure, skin rapture, and delamination. It is found that the foam-filled paper honeycomb sandwich structures can withstand higher bending loads compared to foam core-based and paper honeycomb-based sandwich structures. These developed sandwiches offer potential as green materials due to the characteristics of their constituent materials and can find valuable applications in the building thermal insulation.

Polypyrrole (PPy)-capped caped silver nanowire (Ag NW) nanomaterials (core–shell rod-shaped Ag NW@PPy) were synthesized suing a one–port suspension polymerization technique. The thickness of PPy layer on the 50-nm-thickness/15-μm-length Ag NW was effectively controlled to 10, 40, 50, and 60 nm. Thin films cast from one-dimensional conductive Ag NW@PPy formed a three-dimensional (3-D) conductive porous network structure and provided excellent electrochemical performance. The 3-D Ag NW@PPy network can significantly reduce the internal resistance of the electrode and maintain structural stability. As a result, a high specific capacitance of 625 F/g at a scan rate of 1 mV/s was obtained from the 3-D porous Ag NW@PPy composite film. The cycling performance over a long period exceeding 10,000 cycles was also evaluated. We expect that our core–shell-structured Ag NW@PPy composites and their 3-D porous structure network films can be applied as electrochemical materials for the design and manufacture of supercapacitors and other energy storage devices.

In this study, a novel absorbable hemostatic agent was developed using carrageenan (CRG) as a natural polymer and cerium oxide nanoparticles (CeO2 NPs).  CRG-CeO2-0.5 and CRG-CeO2-1 composites were prepared by compositing CRG and CeO2 at a weight ratio of 200:1 and 100:1, respectively. Physio-chemical and structural properties of these compounds were studied and compared with pristine CRG. Upon incorporation of CeO2 nanoparticles into the CRG matrix, significant reductions in hydrogel degradation were observed. In addition, it was noted that CRG-CeO2 exhibited better antibacterial and hemostatic properties than CRG hydrogel without CeO2.The biocompatibility of the materials was tested using the NIH 3T3 cell line and all samples were found to be nontoxic. Particularly, CRG-CeO2-1 demonstrated superior hemostatic effects, biocompatibility, and a lower degradation rate since more CeO2 Nps were present in the CRG matrix. Therefore, CRG-CeO2-1 has the potential to be used as a hemostatic agent and wound dressing.

Controlling robots in space with necessarily low material and structural stiffness is quite challenging at least in part due to the resulting very low structural resonant frequencies. The frequencies are sometimes so low, the vary act of controlling the robot with medium or high bandwidth controllers lead to excitation of resonant vibrations. Biomimetics or biomimicry emulates models, systems, and elements of nature for solving such complex problems. Recent seminal publications have re-introduced the viability of optimal command shaping, and one recent instantiation mimics baseball pitching to propose control of highly flexible space robots. The readership will find a perhaps dizzying array of thirteen decently performing alternatives in the literature but could be left bereft selecting a method(s) deemed to be best suited for a particular application. Bio–inspired control of space robotics is presented in a quite substantial (perhaps not comprehensive) comparison, and the conclusions of the study indicate the top three performing methods based on minimizing control effort (i.e., fuel) usage, tracking error mean, and tracking error deviation include.

Disrupted nutrient recycling is a significant problem for Europe, while phosphorus and nitrogen are wasted instead of being used for plant nutrition. Mineral phosphate is critical raw material, which contains environmentally hazardous elements such as cadmium and uranium. Therefore, phosphorus recovery from agricultural by-product streams is critically important key priority. Phosphorus recovery from food grade animal bone by-products have been applied researched since 2002 with objective driven evolution progress towards specialized pyrolysis processing technology and animal bone char product (ABC) developments in economical industrial scale. Different animal bone by-products tested under different conditions at 400 kg/h throughput capacity in the continuously operated 3R zero emission autothermal carbonization system. The different material core treatment temperatures (between >300°C and <850°C) were combined with different residence times under industrial productive processing conditions. It has been industrial demonstrated that material core treatment temperature <850°C with 20 minutes residence time is necessary to achieve high quality ABC with useful agronomic value. The output ABC product having concentrated >30% phosphorus pentoxide (P2O5) and specific quality innovative fertilizer for agronomical efficient organic and low input farming applications as functional organic fertilizer, soil improver, growing medium and/or fertilizing product blend with high mineral phosphate fertiliser replacement value.

The research paper investigates the synthesis of metal matrix composites (MMCs) through the amalgamation of aluminum and silicon carbide particles, employing a two-step mixing methodology called the stir casting method. Metal matrix composites are materials that enhance the capabilities of a metallic matrix by incorporating another material. This leads to better characteristics such as tensile and shear moduli, fatigue and fracture properties, thermal expansion coefficient, and more. Aluminum-matrix composites are a class of materials that possess distinct characteristics that may be modified by altering factors such as the type of reinforcing material, the amount of reinforcement, and the fabrication technique employed to produce the composite. The concept aims to combine the desirable properties of metals and ceramics by incorporating durable refractory particles into a malleable metal structure. The fabrication process employs the stir casting technique, where reinforcing phases are mechanically stirred into a molten matrix to create cast composites with reinforcement volume percentages of up to 30%. The study utilizes Response Surface Methodology to enhance the mechanical properties of the composites through the optimization of manufacturing parameters, including stirring temperature, time, and speed. The study entails analyzing the correlation between different casting conditions and the resulting changes in hardness and tensile strength.

This study propounds a sustainable alternative to petroleum-based polyurethane (PU) foams aiming to curtail this nonrenewable resource's continued and uncontrolled use. Coconut fatty acid distillate (CFAD) and crude glycerol (CG), both wastes from vegetable oil processes, were utilized for bio-based polyol production for rigid PU foam application. The raw materials were subjected to catalyzed glycerolysis with alkaline-alcohol neutralization and bleaching. The resulting polyol possessed properties suitable for rigid foam application with an average OH number of 215 mg KOH/g, acid number of 7.2983 mg KOH/g, and Gardner color value of 18. The polyol was used to prepare rigid PU foam, and its properties were determined using FTIR, TGA/DTA, and UTM. Additionally, the cell foam morphology was investigated by scanning electron microscope (SEM) in which most of its structure revealed an open-celled network and quantified at 92.71% open cell content using pycnometric testing. The PU foam thermal and mechanical analysis results showed an average compressive strength of 70.59 kPa, thermal conductivity of 46.50 mWm-1K-1, and density of 32.79 kgm-3. These properties showed its applicability as thermal insulating foam, thus, demonstrating the potential use of CFAD and CG in commercial polyol and PU foam production.

In response to global climate challenges and the increasing demand for energy, exploring renewable energy alternatives has become crucial. Bio-oils, derived from biomass pyrolysis, are emerging as potential replacements for fossil fuel-based liquid fuels. This paper shares findings from the Institute of Energy and Fuel Processing Technology on the quality of crude biomass pyrolysis bio-oil samples. These findings highlight their potential as motor liquid fuels. The article details the results of tests on the physicochemical properties of four distinct bio-oil samples. Additionally, it presents preliminary test results on the hydrodeoxygenation of bio-oils in a batch reactor. The production of homogeneous, stable mixtures using other fuel additives, such as diesel oil, rapeseed methyl ester (RME), and butanol, is also discussed.

Mercury toxicity significantly threatens aquatic ecosystems, particularly impacting fish populations and human well-being. This article exposes the effects of mercury contamination on aquatic life and their habitats. Mercury primarily originates from natural degassing and anthropogenic activities and accumulates in aquatic organisms, most notably in predatory fish, through bio-accumulation and bio-magnification. This bio-accumulation, driven by microbial transformation to methyl-mercury, leads to elevated concentrations in top-level predators. The consequences of mercury exposure on fish physiology are stunted growth, reproductive impairments, and compromised immunity, with potential ramifications for population dynamics and ecosystem resilience. This study delves into specific impacts of mercury on fish, ranging from bone deformities to liver damage, developmental anomalies, neurotoxic effects, and disruptions in reproductive systems. The interplay between ecological, physiological, and human health effects underscores the need for a comprehensive understanding of mercury's underlying mechanisms. Monitoring mercury levels in aquatic systems emerges as a crucial strategy for ensuring fish populations' health and ecosystems' sustainability. Urgent collaborative efforts are imperative to address this global concern, promote harmonious coexistence between human activities and aquatic environments, and secure the availability of safe and nutritious fish for future generations. In conclusion, this article highlights the urgent necessity for targeted interventions and informed decision-making to mitigate the influence of mercury contamination on aquatic ecosystems.

Prime number-related issues can be viewed from drastically different perspectives by examining the close connections between prime numbers and composite numbers. We think that multiple perspectives are the pillars on the path to solutions so we have created this study. As a result of the study, we proposed two new formulas by presenting three theorems and one proof for each theorem, a total of three proofs. We proved that the formula p · n + p returns a composite number in the first of the theorems, which is the preliminary theorem. Our first theorem except the preliminary theorem is that the formula p · n + p returns all composite numbers, and we proved that too. Finally, we created Theorem II using Theorem I to use in our other work and proved that the formula 2 · n · p + p returns all odd composite numbers, which is Theorem II. Afterward, we presented the similarities of the 2 · n · p + p formula we put forth with another known formula.

Integer is either a composite number or a prime number. Therefore, detecting composite numbers is important for solving prime numbers. The study of prime numbers, apart from satisfying human curiosity, can be very important. In this article, the order of composite numbers has been detected. And explained with a simple method and a simple function. And, a method has been developed in which all composite numbers and therefore prime numbers can be determined by using the specified methods, functions and formulas.

Use of porous titanium (Ti) and Ti alloys in orthopedic implants or in light structures requires processing routes that could generate an as-much-as possible control in the pores amount, shape, size and connectivity. In this work, a colloidal approach to the processing of Ti porous structures by the inside foaming of a porogen into a gelled high solid content aqueous suspension of Ti powders, is presented. The prepared slurries contained different amounts of Methyl Cellulose (MC) as gelling agent (8, 10 and 12 g/L) and ammonium bicarbonate (BA) as porogen (15, 20, 25 wt. %). The gel-casted samples were heated at mild temperatures ranging (60, 70 and 80 °C) to promote the gelation and produce, at the same time, the porosity by the thermal decomposition of the ammonium bicarbonate. Different structures are obtained depending on the combination of the study variables

The aim of the present study was to assess the efficacy of All Cosmos Industries (ACI) bio-organic and bio-chemical fertilizers and ACI N-Fixer (N-Bio Booster) on the paddy yields based on the field trial plots at Langkat, Medan, Indonesia. This application of ACI bio-organic fertilizer (NPK 5/5/5) and ACI bio-chemical (NPK 15/15/15) fertilizer and ACI N-Fixer tests were conducted at the paddy farm at Langkat from May-October 2018. This study employed a factorial randomized complete block design which consisted of two factors, namely: Factor I with four types of fertilizers while Factor II consisted of two paddy varieties (Inpari 30 and Inpari 32). Overall, the filled grains in the ACI treatments are significantly (P< 0.05) higher than those in the control treatments that used Normal Chemical Compound NPK. Overall, total weight per meter² (368-617g) in ACI treatments are also significantly (P< 0.05) higher than those (319-371g) in the control treatments. At harvesting time at 105 days after transplanting, significantly higher (P< 0.05) colony counts (13-15 x 10⁶ CFU/mL) (for ACI treatments), than those (8 x 10⁶ CFU/mL) in the controls positively indicated higher total yields of paddy grains per hectare. It was found that the application of ACI bio-organic and bio-chemical fertilizers and ACI N-Fixer can improve paddy yields of the two rice varieties, between 16.4-38.2% (up to 5.75 MT/ha), in the field trial plots at Langkat. These commercial fertilizers play an imperative role in refining the soil fertility and thereby can increase the yield of rice production. Therefore, it is highly recommended that ACI bio-organic and ACI bio-chemical fertilizers and ACI N-Fixer (N-Bio Booster) can be employed to increase the paddy yield in this region.

In this article, two elliptical-ovel-shaped cylindrical dielectric resonator based wideband Graphene inspired reconfigurable metasurface absorber is designed on diffused quartz substrate having a relative permittivity of 3.75 and conductivity 2200Kg/m3 with height of 25μm. This metasurface having gold plated ground in microstrip with 5μm which is essential by calculating skin depth at 2.0THz frequency. Two elliptical ovel shaped patches with Graphene plated having built in potential varies 0-2.5eV and relaxation time 1.0ps at 290oK. By changing the relaxation time of Graphene 0.1ps-0.3ps its resonance frequency also varies i.e., reconfigurable property they provide without adding any active i.e., PIN diode components. The proposed MS is designed having a dimension of 100×100μm2 is designed on a microstrip. This MS works in the range of 1.6-2.38THz having more than 90% absorbance with two transmission zero at 2.1THz and 2.3THz having high Q ˃ 50 which is used to determine the sensitivity where the proposed MS used as a sensor to determine hemoglobin (Blood Glucose level) and urine (Uric acid) by changing their refractive index from 1.34-1.43. Maximum sensitivity achieved at 2000GHz/RIU and average sensitivity for hemoglobin and urine sensing achieved 833.33GHz/RIU, FOM-8.33 and 4277.7733GHz/RIU, FOM-555.55 respectively.

Alzheimer's disease (AD) detection acting as an essential role in global health care due to misdiagnosis and sharing many clinical sets with other types of dementia, and costly monitoring the progression of the disease over time by magnetic reasoning imaging (MRI) with consideration of human error in manual reading. This paper goal a comparative study on the performance of data mining techniques on two datasets of Clinical and Neuroimaging Tests with AD. Our proposed model in the first stage, Apply clinical medical dataset to a composite hybrid feature selection (CHFS), for extract new features to select the best features due to eliminating obscures features, In parallel with Apply a novel hybrid feature extraction of three batch edge detection algorithm and texture from MRI images dataset and optimized with fuzzy 64-bin histogram. In the second stage, we applied a clinical dataset to a stacked hybrid classification(SHC) model to combine Jrip and random forest classifiers with six model evaluations as meta-classifier individually to improve the prediction of clinical diagnosis. At the same stage of improving the classification accuracy of neuroimaging (MRI) dataset images by applying a convolution neural network (CNN) in comparison with traditional classifiers, running on extracted features from images. The authors have collected the clinical dataset of 426 subjects with (1229 potential patient sample) from oasis.org and (MRI) dataset from a benchmark kaggle.com with a total of around ~5000 images each segregated into the severity of Alzheimer's. The datasets evaluated using an explorer set of weka data mining software for the analysis purpose. The experimental show that the proposed model of ‏(CHFS) feature extraction ‏ lead to effectively reduced the false-negative rate with a relatively high overall accuracy with a stack hybrid classification of support vector machine (SVM) as meta-classifier of 96.50% compared to 68.83% of the previous result on a clinical dataset, Besides a compared model of CNN classification on MRI images dataset of 80.21%. The results showed the superiority of our CHFS model in predicting Alzheimer's disease more accurately with the clinical medical dataset in early-stage compared with the neuroimaging (MRI) dataset. The results of the proposed model were able to predict with accurately classify Alzheimer's clinical samples at a low cost in comparison with the MRI-CNN images model at the early stage and get a good indicator for high classification rate for MRI images when applying our proposed model of SHC.

Herein we report the expansion of the chemical space available from the chitin, accessible via the biogenic N-platforms 3A5AF, M4A2C and di-HAF. The biologically active heteroaromatics furo[3,2-d]pyrimidin-4-one and furo[3,2-d]pyrimidin-4-amine can be selectively accessed from 3A5AF and M4A2C, respectively. The chiral pool synthon di-HAF is a viable substrate for the Achmatowicz rearrangement, providing streamlined access to 2-aminosugars possessing a versatile hydroxymethyl group at C5.

Wearable touch sensors, which can convert force or pressure signals into quantitative electronic signals, have emerged as an essential smart sensing devices and played an important role in various cutting-edge fields, including wearable health monitoring, soft robots, electronic skin, artificial prosthetics, AR/VR, and the Internet of Things. Flexible touch sensors have made significant advancements, while construction of novel touch sensors via mimicking the unique properties of biological materials and biogenetic structures always remains a hot research topic and significant technological pathway. This review provides a comprehensive summary of the research status of wearable touch sensors constructed by imitating the material and structural characteristics in nature, and also summarizes the scientific challenges and development tendency of this aspect. Firstly, the research status for constructing flexible touch sensors based on biomimetic materials is summarized, including hydrogel materials, self-healing materials, and other bioinspired or biomimetic materials with extraordinary properties. Then, design and fabrication of flexible touch sensors based on bionic structures for performance enhancement are fully discussed. These bionic structures include special structures in plants, special structures insects/animal, and special structures in human body. Moreover, a summary of the current issues and future prospects for developing wearable sensors based on bioinspired materials and structures is discussed.

Polyamides (PAs) are one of the most important engineering polymers; however, the difficulty in dissolving them hinders their applications. Formic acid (FA) is the most common solvent for PAs, but it has industrial limitations. In this contribution, we proposed a new solvent system for PAs by replacing a portion of the FA with urea and calcium chloride (FAUCa). Urea imparts the hydrogen bonding and calcium ion from the calcium chloride, as a Lewis acid was added to the system to compensate for the pH decrease due to the addition of urea. The results showed that the proposed solvent (FAUCa) could readily dissolve PAs, resulting in less decrease in the mechanical properties during the dissolution. The composite prepared using the FAUCa has almost the same properties like the one prepared using the FA solution. The solution was applied on a polyamide 66 fabric to make an all-polyamide composite coated-fabric, which then was characterized. The FAUCa solution had a higher viscosity than the one prepared using the neat FA solvent, which can be an advantage in the applications which needs higher viscosity like preparing the all-polyamide composite coated-fabric. A more viscouse solution makes a denser coating which will increase the water-/gas-tightness. In conclusion, using the FAUCa solvent has two merits: 1. replacement of 40 % of the FA with less harmful and environmentally-friendly chemicals and 2. enabling for the preparation of more viscouse solutions, which makes denser coating.

Modern day construction is widely influenced using concrete-steel composite columns. A lot of research on concrete-steel composite columns is being carried out around the world. The rapid growth in concrete-steel composite construction has widely decreased the use of conventional reinforced cement concrete construction (R.C.C), and the steel construction practices. The concrete-steel composite construction has obtained an extensive receiving around the globe. As Pakistan is a developing country, so, it is relatively a new concept for its construction industry when compared with the developed countries around the globe. Although, the R.C.C construction is suitable and economical for construction of framing systems of low-rise buildings, however, the increased dead load, span restrictions, less stiffness and risky formwork makes it uneconomical and unviable when it comes across the construction of intermediate to high-rise buildings. This research is an effort to learn the cost effectiveness, increased or decreased stiffness, and change on the functionality of the composite construction for intermediate to high-rise buildings constructed in Pakistan. A Base + Ground + 11 storey commercial building is selected for this study. A comparison is made between conventional R.C.C columns structure and concrete-encased composite columns structure. The equivalent static nonlinear analysis is performed using ETABS 2017 software. Although, for Base + Ground + 11 storey building, the construction cost of concrete-encased composite structure is 7.7% more than the conventional R.C.C columns structure, but the concrete-encased composite structure will have 13.013% more constructed floor area. This increased floor area helps to settle the cost difference between the two structures.

The composition of fine-ground lead zirconate-titanate powder Pb(Zr_0.52Ti_0.48)O₃, suspended in PZT and bismuth titanate (BiT) solutions, is deposited on the curved surface of IN718 and IN738 nickel-based supper alloy substrates up to 100 µm thickness. Photochemical metal organic and infiltration techniques are implemented to produce smooth, semi-dense, and crack-free random orientated thick piezoelectric films as piezo-sensors, free of any dopants or thickening polymers. Every single layer of the deposited films is heated at 200 °C with 10 wt.% excess PbO, irradiated by UV lamp (365 nm, 6 watt) for 10 minutes, pyrolyzed at 400 °C, and subsequently annealed at 700 °C for one hour. This process is repeated successively until reaching the desired thickness. Au and Pt thin films are deposited as the bottom and top electrodes using evaporation and sputtering methods, respectively. PZT/PZT and PZT/BiT composite films are then characterized and compared to similar PZT and BiT thick films deposited on the similar substrates. The effect of composition and deposition process is also investigated on the crystalline phase development and microstructure morphology as well as dielectric, ferroelectric and piezoelectric properties of piezo-films. The maximum remnant polarization of P_r = 22.37 ± 0.01, 30.01 ± 0.01 µC/cm², the permittivity of ε_r = 298 ± 3, 566 ± 5 and piezoelectric charge coefficient of d₃₃ = 126, 148 m/V were measured versus the minimum coercive field of E_c = 50, 20 kV/cm for the PZT/PZT and PZT/Bit thick films, respectively. The thick film piezo-sensors are developed to be potentially used at frequency bandwidth of 1–5 MHz for rotary structural health monitoring and also in other industrial or medical applications as a transceiver.

.Various synthetic nematicides are currently used effectively in the control of plant parasitic nematodes. However, these nematicides have adverse effects on humans and the environment. Neem oil is eco-friendly alternatives to synthetic nematicides. The effectiveness of repeated neem oil application in suppressing the root-knot nematodes infestation in figs seedlings was therefore examined in this study, both in its natural form (10 ml/L) and in its nano-emulsion form (5 and 7 ml/L). The recorded reduction parameters of M. incognita were J2/250g soil, galls and egg masses / 5g roots of infected fig seedlings were measured at that time, and the effects of these natural additives were compared with the Fosthiazate (Krenkel 75%EC). The impact of such soil amendments on some typical plant parameters, the total microbial count of soil, and the overall enzymatic activity of the fig rhizosphere were also included. Obtained results revealed that the soil population density of root knot nematode suppressed by 80.3% , reduction of nematode egg masses (60.4%) due to the application of nano-emulsion of neem oil (at 7ml/L). Present work recommend the use of nano-emulsion of neem oil as one of the effective and eco-friendly means to reduce the root- knot nematode on fig .

The authors of this paper use an original method of diatomaceous earth fractionation, which allows for obtaining a filler with a specific particle size distribution. The method makes it possible to separate small, disintegrated and broken diatom frustules from those which maintained their original form in diatomaceous earth. The study covers a range of tests conducted to prove that such a separated diatomic fraction shows features different from the base diatomite used as an epoxy resin filler. We have examined mechanical properties of a series of diatomite/resin composites considering the weight fraction of diatoms and the parameters of the composite production process. The studied composites of Epidian 601 epoxy resin cross-linked with amine-based curing agent Z-1 contained 0 to 70% vol. of diatoms or diatomaceous earth. Samples were produced by casting into silicone moulds in vacuum degassing conditions and, alternatively, without degassing. The results have shown that the size and morphology of the filler based on diatomaceous earth affects mechanical and rheological properties of systems based on epoxy resin.

Application of native PGPR as bio inoculant is an alternative sustainable agricultural practice to enhance crop productivity, grain quality, and soil fertility. In this view, a study was to examine the effect of either individual or consortium PGPR inoculation on growth, yield, and grain nutrient uptake of two teff varieties. The pot experiment was carried out in (CRD) three replication and 10 treatments. The PGPR inoculants used in this study were Pseudomonas fluorescens biotype G, Enterobacter cloacae ss disolvens, and Serratia marcescens ss marcescen and their consortium. Dukem and Magna varieties were used in this study. The results of the analysis of variance showed significant differences (P ≤ 0.001) among the treatment and most of the agronomic traits except number of fertile tillers and also significant different (P ≤ 0.01) for grain P and N uptake. The variety was significantly affected grain Mg, Zn and Fe uptake at 5 % probability level and did not significantly influence all agronomic traits of the two varieties. Furthermore, interaction effects of two factors (TM*VT) were significant differences (P ≤ 0.05) for plant height and panicle length. Individual treatments mean comparison results showed that inoculation of native PGPR consortium significantly affected most of the PGP traits at (P ≤ 0.05). The maximum traits like plant height (189cm), panicle length (66.7cm), shoot dry biomass (9.98g), root dry biomass (2.90g) and grain yield per plant (4.55g) were observed from Dz-01-196. It could be concluded that the consortium of native PGPR inoculants for plant growth, yield and grain nutrient uptake improvement performed better than their individual strain.

Composites with HDPE and PLA matrix have been tested to analyse the effect of natural fillers (wood flour, recycled waste paper and a mix of both fillers) and temperature on polymer degradation. Composting tests have been performed in both mesophilic (35°C) and thermophilic (58°C) conditions. Degradation development has been evaluated through mass variation, TGA and DSC. HDPE, as expected, did not display any relevant variation, confirming its stability under our composting conditions. PLA is sensibly influenced by temperature and humidity, with higher reduction of Mw when composting is performed at 58°C. Natural fillers seem to influence degradation process of composites, already at 35°C. In fact, degradation of fillers at 35°C allows a mass reduction during composting of composites, while neat PLA do not display any variation.

This work aims to investigate the effect of process temperature and catalyst content by pyrolysis and thermal catalytic cracking of (organic matter + paper) fraction from municipal household solid waste (MHSW) on the yields of reaction products (bio-oil, bio-char, H2O, and gas), acid value and chemical composition of bio-oils, and characterization of bio-chars, in laboratory scale. The collecting sectors of MHSW in the municipality of Belém-Pará-Brazil were chosen based on geographic and socio-economic database. The MHSW collected and transported to the segregation area. The gravimetric analysis of MHSW carried out and the fractions (Paper, Cardboard, Tetra Pack, Hard Plastic, Soft Plastic, Metal, Glass, Organic Matter, and Inert) separated. The selected organic matter and paper submitted to pre-treatment of crushing, drying, and sieving. The experiments carried out at 400, 450, and 475 °C and 1.0 atmosphere, and at 475 °C and 1.0 atmosphere, using 5.0, 10.0, and 15.0% (wt.) Ca(OH)2, in batch mode. The bio-oil characterized for acid value. The chemical functions present in bio-oil identified by FT-IR and the composition by GC-MS. The bio-char characterized by SEM, FT-IR and XRD. The variance in mass (wt.%) for organic fraction of municipal household solid waste, between 56.21 and 67.45% (wt.), lies with the interval of 56% (wt.) and 64% (wt.) of OFMHSW for middle and low income countries. The pyrolysis of MHSW fraction (organic matter + paper) show bio-oil yields between 2.63 and 9.41% (wt.), aqueous phase yields between 28.58 and 35.08% (wt.), solid phase yields between 35.29 and 45.75% (wt.), and gas yields between 16.54 and 26.72% (wt.). The bio-oil yield increases with pyrolysis temperature. For the catalytic cracking, the bio-oil and gas yields increase slightly with CaO content, while that of bio-char decreases, and the H2O phase remains constant. The GC-MS of liquid reaction products identified the presence of hydrocarbons (alkanes, alkenes, alkynes, cycloalkanes, and aromatics) and oxygenates (carboxylic acids, ketones, esters, alcohols, phenols, and aldehydes), as well as compounds containing nitrogen, including amides and amines. The acidity of bio-oil decreases with increasing process temperature and with aid Ca(OH)2 as catalyst. The concentration of hydrocarbons in bio-oil increases with increasing Ca(OH)2-to-MHSW fraction ratio due to the catalytic deoxygenation of fatty acids molecules, by means of de-carboxylation/de-carbonylation, producing aliphatic and aromatic hydrocarbons.

Acoustic energy dissipates in multi-phase or multi-boundary materials. Hybrid composites are described as multi-phase with many interfaces between their materials. The current research proposes studying the acoustic behavior of polymeric hybrid composites by estimating the time, velocity, and hybrid composite acoustic impedance. Two groups of hybrid composites were prepared, including unsaturated polyester with PMMA, except one with HDPE and the other with PS. Each group has 28, 35, and 40% weight fractions. An ultrasonic test measured time to determine velocity and acoustic impedance later. The results show that increasing the weight fraction will increase density with respect to the density of the reinforcing material. Different ultrasonic times were obtained with increasing weight fractions. As the weight fraction of PS increased, the time increased; unlike the velocity, it decreased but increased with density. In contrast, this behavior was changed if the hybrid had PE. The highest acoustic impedance was at 28% UP/PMMA+PS. In conclusion, UP/PMMA+PS can dissipate ultrasonic waves more than UP/PMMA+PE.

In the present study, piecewise integrated composite (PIC) bumper beam for passenger cars was proposed and design optimisation process for composite bumper beam against IIHS test was carried out with the help of machine learning. Several elements in IIHS bumper FE model have been assigned to be references, in order to collect training data which, allow the machine learning model to study the method of predicting loading types of each finite element. 2-D and 3-D implementations were provided by machine learning models, which determined stacking sequences of each finite element in PIC bumper beam. It was found that the PIC bumper beam, which was designed by machine learning model has direct impact on reducing the possibility of failure as well as increasing bending strength effectively than conventional composite bumper beam. Moreover, 3-D implementation produced better results compared with 2-D implementation since it was preferable to choose loading type information which was achieved from surroundings when the target elements were located either at corner or junction of planes instead of using information came from the same plane of target.

In this paper a robust version of the Wald test statistic for composite likelihood is considered by using the composite minimum density power divergence estimator instead of the composite maximum likelihood estimator. This new family of test statistics will be called Wald-type test statistics. The problem of testing a simple and a composite null hypothesis is considered and the robustness is studied on the basis of a simulation study. Previously, the composite minimum density power divergence estimator is introduced and its asymptotic properties are studied.

Castor oil may be differentiated from other non-edible vegetable oils because of its main composition of hydroxylated fatty acids. Ricinoleic acid comprises 80–90% wt. of fatty acids in castor oil (Ricinus communis). In this study, the thermo-oxidative stability and tribological behavior of bio-based lubricant samples synthesized from castor oil using isoamyl alcohol were evaluated. Initially, the compositional and physicochemical properties of the obtained samples were assessed using 1H NMR, FTIR, and ASTM methods. Oxidative stability of the samples was evaluated using Rancimat method at 110 °C under air flow. The final biolubricant sample (BL2), obtained after esterification, epoxidation, and oxirane rings opening reactions, presented an oxidation stability time (OST) of 14.3 h. The thermal stability was also evaluated by thermogravimetry (TG) from the mass variations under inert and oxidative atmosphere. BL2 showed higher thermal stability compared to the other samples, demonstrating higher decomposition temperatures in both inert (339.04 °C) and oxidative (338.47 °C) atmospheres, for a mass loss of 50%. The tribological properties of the samples were evaluated using a four-ball tribometer configuration. The BL1 and BL2 samples exhibited lower friction coefficients than the mineral oil sample (MOS) by 21.5% and 43.1%, respectively. Regarding wear, the observed wear scar diameter (WSD) was also lower in BL1 and BL2 compared to MOS by 5.2% and 40.4%, respectively. The results of the tribological evaluation suggest that both samples obtained in this study have promising potential for applications in lubricating machines and mechanical systems.

Wastewater contaminated with antibiotics is a major environmental challenge. We developed here the green synthesis of bio-graphenes by using natural precursors (Xanthan, Chitosan, Boswellia, Tragacanth). The use of these precursors can act as templates to create 3D doped graphene structures with special morphology. Also, this method is a simple method for in-situ synthesis of doped graphenes. The elements present in the natural polymers (N) and other elements in the natural composition (P, S) are easily placed in the graphene structure and improve the catalytic activity due to the structural defects, surface charges, increased electron transfers, and the high absorption. In this mechanism, O2 dissolved in water absorbs onto the positive charged C in doped graphenes to create oxygenated radicals, which enables the degradation of antibiotic molecules. Light irradiation increases the amounts of radicals and rate of antibiotic removal. The results have shown that the hollow cubic Chitosan-derived graphene has shown the best performance due to the doping of N, S, and P. The Boswellia-derived grapheme shows the highest surface area, but lower catalytic performance, which indicates the more effective role of doping in the catalytic activity. The effect of oxygen and light were also studied to accelerate the degradation process.

In this work, the inhibition properties of new bio-based lignine ILs on the corrosion of mild steel in an aqueous solution of 0.01 M NaCl were investigated by Potentiostatic Electrochemical Impedance Spectroscopy (PEIS), Cyclic Potentiodynamic Polarization (CPP). Moreover, the surface was characterized using SEM, EDS, and optical profilometry. The influence of cation and anion on the inhibitor properties and a possible synergistic effect were investigated. The IL choline syringate showed a promising performance, reducing the corrosion current after 24-hour immersion in 0.01 M sodium chloride, from 1.66 µA/cm2 for the control to 0.066 µA/cm2 with 10 mM of the IL present. In addition to the performance as a corrosion inhibitor, both components of this IL also meet or exceed current additional desired properties of such compounds, being readily available, economically efficient, and well tolerated in organisms and the environment.

This study evaluates the production of biohydrogen from agro industrial waste. The worldwide energy demand is increasing exponentially and the reserves of fossil fuels are depleting, the combustion of fossil fuels has the effect on environment because of CO2 emission. Hydrogen generation market size is forecast to cross 180 billion by 2024, according to a new research report by global market. For the production of biohydrogen. we had chosen groundnut shell as our source, using Tween80 as a surfactant we had undergone pre-treatment studies for (10min,20min,30min,40min,50min) we had estimated the content of cellulose, protein, carbohydrates at (1%,2%,3%,4%,5%) and obtained the optimum value in the form of graph. The production of hydrogen is done by using the rumen fluid of the cow and the quantity of the hydrogen produced by this process is identified by using the analytical instrument Gas Chromatography.