A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Drainage systems are usually dimensioned for design storms based on intensity-duration-frequency (IDF) curves of extreme precipitation. For each location, different IDF curves are established based on local hydrological conditions. Recent research shows that these curves also vary with time, and should be updated with recent data. The purpose of this study is to evaluate IDF curves obtained from precipitation simulations from the Eta RCM, comparing them with IDF curves obtained from data of a rainfall station. Climate models can be a useful tool for assessing the impacts of climate changes on drainage systems, referring precipitation forecasts. In this study, the Eta RCM was forced by two global climate models: HadGEM2-ES and MIROC5. The bias of the precipitation data, generated by RCM models, was corrected using a Gamma distribution. The Juqueriquerê River Basin, in the cities of Caraguatatuba and São Sebastião, São Paulo State, Brazil, was chosen as a case study. The results show a good correlation between the IDF curves of simulated and observed rainfall for the control period (1960-2005), indicating the strong possibility of using the Eta RCM precipitation forecasts for 2007 - 2099 to establish future IDFs thereby, taking into account climate changes in urban drainage design.

High-throughput screening technologies continues to produce large amounts of multiomics data from different populations and cell types for various diseases, such as cancer. However, analysis of such data encounters difficulties due to cancer heterogeneity, further exacerbated by human biological complexity and genomic variability. There is a need to redefine the drug discovery development pipeline, bringing an Artificial Intelligence (AI)-powered informational view that integrates relevant biological information and explores new ways to develop effective anticancer approaches. Here, we show SynPred, an interdisciplinary approach that leverages specifically designed ensembles of AI-algorithms, links omics and biophysical traits to predict synergistic anticancer drug synergy. SynPred exhibits state-of-the-art performance metrics: accuracy – 0.85, precision – 0.77, recall – 0.75, AUROC – 0.82, and F1-score - 0.76 in an independent test set. Moreover, data interpretability was achieved by deploying the most current and robust feature importance approaches. A simple web-based application available online at http://www.moreiralab.com/resources/synpred/ was constructed to predict synergistic anticancer drug combinations requiring only the upload of the two drug SMILES to be tested, allowing easy access by non-expert researchers.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

Capital structure decision plays an imperative role in firm’s performance. Recognizing the importance, there has been many studies inspected the rapport of capital structure with performance of firms and findings of those studies are inconclusive. In addition, there is relative deficiency of empirical studies examining the link of capital structure with performance of banks in Bangladesh. This paper attempted to fill this gap. Using panel data of 22 banks for the period of 2005-2014, this study empirically examined the impacts of capital structure on the performance of Bangladeshi banks assessed by return on equity, return on assets and earnings per share. Results from pooled ordinary least square analysis show that there are inverse impacts of capital structure on bank’s performance. Empirical findings of this study is of greater significance for the developing countries like Bangladesh because it will call upon concentration of the bank management and policy makers to pursue such policies to reduce reliance on debt and to accomplish optimal level capital structure. This research also contributes to empirical literatures by reconfirming (or otherwise) findings of previous studies.

Abstract: Understanding the reliability and sensitivity of jump testing is essential to determine the neuromuscular progress of athletes and make informed decisions. This study aimed to assess the reliability and sensitivity of countermovement jump (CMJ) and drop jump (DJ) tests metrics in female volleyball players. Sixteen semi-professional female volleyball players participated in the study. Intrasession and intersession reliability of CMJ and DJ metrics were evaluated using a randomized cross-over design. Dual force platform was used to collect data, and several dependent variables were calculated using forward dynamics. Intraclass correlation coefficients (ICC), coefficients of variation (CV) and minimum difference (MD) were calculated. The third attempt presented the highest values for both test, and changes in jump strategy in DJ. CMJ is consistent across sessions, while DJ also shows intersession differences (p<0.05) in 11 out of 15 variables. Most CMJ variables exhibit excellent reliability while DJ variables have lower reliability and higher variability. Concentric and eccentric impulses for DJ showed excellent reliability. Most CMJ variables showed excellent reliability and variability, DJ had lower reliability, higher variability, and lower sensitivity. These findings provide valuable information when assessing athletes' performance and highlight the reliability, sensitivity, and variability in jump performance for CMJ and DJ tests.

Despite the recognized influence of maximum or acceleration strength on combat techniques and countermovement jump (CMJ) performance, the relationship between body segment weights and combat techniques remains unexplored. This study aimed to examine the impact of body segment weights, including striking arm weight (SAW), kicking leg weight (KLW), and trunk weight (TW), on the dynamics of direct punches (DP), palm strikes (PS), elbow strikes (ES), front kicks (FK), and CMJ performance. Sixteen male military cadets (22.3±1.8 years, 181.4±7.0 cm, 83.0±8.1 kg) performed combat techniques, with performance measured by using a force plate and body segment weights assessed by Dual-energy X-ray absorptiometry. Spearman's correlation analysis was applied. Results indicated a strong correlation between KLW and FK impulse (r = 0.64, p ≤ 0.01) and CMJ impact force (r = 0.80, p ≤ 0.01). SAW showed moderate correlations with DP impulse (r = 0.53, p ≤ 0.05) and ES impulse (r = 0.54, p ≤ 0.05). Additionally, FK peak and impact forces were strongly correlated with CMJ jump height (r = 0.74, p ≤ 0.01; r = 0.77, p ≤ 0.01), and FK peak force moderately correlated with CMJ peak velocity (r = 0.63, p ≤ 0.05). These findings suggest targeted arm strength training could enhance striking abilities, while improvements in leg acceleration strength may directly boost kicking performance and vertical jump capabilities, which are crucial in combat scenarios.

Antimicrobial resistance (AMR) poses a critical global health threat, leading to approximately 1.27 million deaths annually from infectious diseases resistant to existing antibiotics. Factors such as antibiotic misuse and environmental contamination have accelerated AMR, with the COVID-19 pandemic exacerbating the issue due to increased antibiotic usage. However, the development of new antibiotics has stagnated, with only a few approved in recent years, and many facing resistance. Among the priority pathogens identified by the WHO, Pseudomonas aeruginosa stands out as a significant concern due to its multidrug resistance and virulence. P. aeruginosa infections are challenging to treat due to intrinsic and acquired resistance mechanisms, as well as its ability to form biofilms. Additionally, P. aeruginosa produces a plethora of virulence factors, including proteases, siderophores, and toxins, further complicating treatment. Quorum sensing (QS) systems play a crucial role in regulating bacterial physiology and virulence factor expression. P. aeruginosa employs three QS systems, making it an attractive target for quorum quenching (QQ) strategies. Enzymes such as AHL lactonases, acylases, and oxidoreductases have shown promise in inhibiting QS, thus reducing virulence without impacting bacterial growth. Furthermore, natural QS inhibitors produced by various organisms offer potential therapeutic alternatives. Despite promising results in vitro, translating QQ strategies to clinical settings remains challenging. Nevertheless, QQ represents a novel approach in combating multidrug-resistant infections and warrants further investigation as a complementary therapeutic strategy alongside traditional antibiotics. This review summarizes enzymes with Qurorum Quenching activity evaluated against the pathogen P. aeruginosa and their potential applications in combination therapies.

Efficient heat management and control in optical devices, facilitated by advanced thermo-optic materials, is critical for many applications such as photovoltaics, thermal emitters, mode-locked lasers, and optical switches. Here, we investigate the thermo-optic properties of 2D graphene oxide (GO) films by precisely integrating them onto microring resonators (MRRs) with control over the film thicknesses and lengths. We characterize the refractive index, extinction coefficient, thermo-optic coefficient, and thermal conductivity of for the GO films with different layer numbers and degrees of reduction, including reversible reduction and enhanced optical bistability induced by photo-thermal effects. Experimental results show that the thermo-optic properties of 2D GO films vary widely with the degree of reduction, with significant polarization anisotropy, enabling efficient polarization sensitive devices. The versatile thermo-optic response of 2D GO substantially expands the scope of functionalities and devices that can be engineered, making it promising for a diverse range of thermo-optic applications.

Emerging autologous cellular therapies that utilize platelet-rich plasma (PRP) applications have the potential to play adjunctive roles in a variety of regenerative medicine treatment plans. There is a global unmet need for tissue repair strategies to treat musculoskeletal (MSK) and spinal disorders, osteoarthritis (OA), and patients with chronic complex and recalcitrant wounds. PRP therapy is based on the fact that platelet growth factors (PGFs) support the three phases of wound healing and repair cascade (inflammation, proliferation, remodeling). Many different PRP formulations have been evaluated, originating from human, in vitro, and animal studies. However, recommendations from in vitro and animal research often lead to different clinical outcomes because it is difficult to translate non-clinical study outcomes and methodology recommendations to human clinical treatment protocols. In recent years, progress has been made in understanding PRP technology and the concepts for bioformulation, and new research directives and new indications have been suggested. In this review, we will discuss recent developments regarding PRP preparation and composition regarding platelet dosing, leukocyte activities concerning innate and adaptive immunomodulation, serotonin (5-HT) effects and pain killing. Furthermore, we discuss PRP mechanisms related to inflammation and angiogenesis in tissue repair and regenerative processes. Lastly, we will review the effect of certain drugs on PRP activity, and the combination of PRP and rehabilitation protocols.

Classical Arabic poetry is a form of Arabic literature, and almost every piece of Arabic poetry follows one of the 16 meters. The rhythmic framework of the poems or the verses is called meters. The deep learning (DL) model was implemented using TensorFlow in this work using a large dataset of Arabic poetry. The character level encoding was used to convert text to integers for classifying the full-verse and half-verse data. The study evaluates the data without removing diacritics from the text. The train-test-split method with a 70-15-15 split was employed for classification. 15% of the total data was considered unseen test data for all models. The work was conducted with multiple deep learning models, including the Long Short-Term Memory (LSTM), Gated Recurrent Units (GRU), and Bidirectional LSTM (Bi-LSTM). The Bi-LSTM model shows the best accuracy of all the models specified, with 97.53% for full-verse and 95.23% for half-verse without removing diacritic data.

The oil and gas industry in Nigeria, a vital contributor to the nation's economy, has long been associated with significant environmental challenges. Pollution, habitat destruction, and greenhouse gas emissions have raised global concerns about sustainability and corporate responsibility. This empirical study explores the relationship between environmental accounting practices and the financial performance of listed oil and gas companies in Nigeria. We investigated eight oil and gas companies that are publicly traded on the Nigerian Stock Exchange Market (NGX) as of January 17, 2022, from 2011 to 2022. The study employs Driscoll-Kraay standard errors and reveals that environmental accounting had significant effects on returns on assets, earnings per share, and liquidity ratio. The study revealed that the implementation of environmental accounting practices had diverse effects on the performance of oil and gas companies in Nigeria. The findings encourage policymakers and stakeholders in the sector to utilise the insights and design more effective regulations and incentives that promote environmental corporate responsibility. Also, valuable insights into the potential benefits and challenges associated with adopting environmental accounting practices, and influencing the decision-making processes of corporate stakeholders were provided to ensure sustainability in terms of improved financial performance of the oil and gas sector in Nigeria.

Aim: The aim of this study was to investigate if tests used to assess core stability could be used to determine success in physiological tests applied to assess dynamic balance and agility for a young active population. Methods: Pearson's r correlation coefficient was used to assess the relationship between the core stability tests and the dynamic balance and agility tests. Evaluation of the tests was established using Cronbach's coefficient of variance as part of intra-rater reliability tests. An analysis of 18 active college aged students was conducted (males: n= 13, females: n= 5). The mean ± SD age for males was 19.2 years ± 3.22 years and for females was 19.4 years ± 1.14 years. Conclusion: The results indicate that there is no significant relationship between tests that assess core stability and tests conducted to assess dynamic balance in active young adults. With the exception of the abdominal flexion test, no significant relationship exists between the remaining core stability tests and agility T-Test. Core stability is not a determinant of balance and agility.

In this paper, we study the constrained minimization problem for an energy functional which is related to the following Kirchhoff type equation \begin{equation*} -\Big(\eta+b\big(\int_{\R^{3}}|\nabla u|^{2}dx\big)^{s}\Big)\Delta u+V(x)u=\mu u +\lambda|u|^{p}u,\end{equation*} where $b$ is a positive constant, parameters $\eta\geq0, \lambda>0$, exponents $s>0$, $0

This study explores novel techniques to improve the detection accuracy of skarn iron deposits using advanced image processing methodologies. Leveraging the capabilities of Aster image, Band Ratio (BR) images, and Principal Component Analysis (PCA), alongside the power of 3D Convolutional Neural Networks (3D-CNN), the research aims to enhance the precision and efficiency of ore detection in complex geological environments. The proposed method employs a specific 3D-CNN architecture, accepting input as a 7×7×C image patch, where C represents the combined number of selected Aster image bands, Principal Component (PC) bands, and computed BR images. To evaluate the accuracy of the proposed method, five distinct image bands combinations, including the proposed bands combination, were tested and evaluated based on the overall accuracy (OA), average accuracy (AA), and kappa coefficient. The results demonstrated that while the incorporation of BR images alongside Aster bands initially seemed promising, it introduced significant confusion in certain classifications, leading to unexpected mis-classification rates. Surprisingly, utilizing solely Aster bands as input parameters yielded higher accuracy rates (OA= 93.13%, AA = 91.96%, Kappa = 90.91%) compared to scenarios involving the integration with band ratios (OA = 87.02%, AA = 79.15, and Kappa = 82.60%) or the integration of BR images to PC bands (OA= 87.78%, AA = 82.39%, Kappa = 83.81%). However, the amalgamation of Aster bands with selected PC bands showed slight improvements in accuracy (OA= 94.65%, AA = 92.93%, Kappa = 93.45%), although challenges in accurately classifying certain features persisted. Ultimately, the proposed combination of Aster bands, PC bands, and BR images (proposed bands combination) presented the most visually appealing and statistically accurate results (OA = 96.95%, AA= 94.87%, and Kappa = 95.93%), effectively addressing misclassifications observed in the other combinations. These findings underscore the synergistic contributions of each of the Aster bands, PC bands, and BR images, with Aster bands proving pivotal for optimal skarn classification, PC bands enhancing intrusions classification accuracy, and BR images strengthening wall rock classification accuracy. In conclusion, the proposed combination of input image bands emerges as a robust and comprehensive methodology, demonstrating unparalleled accuracy in the remote sensing detection of skarn iron minerals.

Six bacterial strains with differing abilities to produce varying concentrations of Indole Acetic Acid were tested individually and in consortia for plant growth promoting and fitness related traits of Cicer arietinum. In all experiments the presence of the nitrogen fixer Mesorhizobium ciceri resulted in increased biomass production. In the absence of this strain, IAA Psedomonas putida and Bacillus megaterium hinder plant growth and fitness related traits. The application of mixes of the three strains always resulted in better plant performance when M. ciceri was present. Whereas P. putida has a noticeable plant growth-promoting effect B. megaterium resulted less effective. The low levels of IAA produced by the selected strains had a significantly greater positive effect on plant biomass accumulation, flower, pods and seed production as well as on total plant nitrogen and nitrogen concentration in seed than high IAA producer strains.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

Maize is an important staple food crop in sub-Saharan Africa (SSA). However, the average grain yield on farmers’ fields falls considerably short of the demand of the region’s population. In addition, the normal endosperm maize widely consumed in SSA is deficient in vitamin A. Drought, a consequence of climate change, is a major constraint to maize production, resulting in seasonal low grain yield in farmers’ fields. The objectives of this study were to assess the performance of newly developed extra-early maturing provitamin A hybrids under managed drought and well-watered conditions, compare the outcomes of multiple trait base-index and multi-trait genotype-ideotype distance index selection procedures, and identify drought-tolerant hybrids with stable performance across contrasting environments for commercialization in SSA. One hundred and ninety provitamin A hybrids and six checks were evaluated under managed drought and well-watered conditions at Ikenne for two seasons between 2021 and 2023. A 14*14-lattice design was used for the field evaluations under both research conditions. Drought stress was achieved by the complete withdrawal of irrigation water 25 days after planting. Results revealed significant differences among the hybrids under drought and well-watered conditions. Grain yield, ears per plant, and plant aspect under managed drought were correlated to the same traits under well-watered conditions suggesting that the expression of these traits is governed by common genetic factors. Twenty-nine hybrids were identified as top-performing drought-tolerant hybrids by the multiple trait base index and multiple-trait genotype–ideotype distance index. Of the selected outstanding 29 hybrids, 34% were derived from crosses involving the tester TZEEIOR 197, demonstrating the outstanding genetic potential of this inbred line. Further analysis of the 29 selected hybrids revealed TZEEIOR 509 × TZEEIOR 197 as the hybrid that combined the most drought-tolerant adaptive traits. However, the hybrids TZEEIOR 526 × TZEEIOR 97, TZEEIOR 384 × TZEEIOR 30, TZEEIOR 515 × TZEEIOR 249, TZEEIOR 510 × TZEEIOR 197, TZEEIOR 479 × TZEEIOR 197, and TZEEIOR 458 × TZEEIOR 197 were identified as the most stable hybrids across drought and well-watered conditions. These hybrids should be extensively tested in multi-location trials for deployment and commercialization in SSA.

The application of deep learning algorithms to predict the molecular profiles of various cancers from digital images of hematoxylin and eosin (H&E)-stained slides has been reported in recent years, mainly in gastric and colon cancers. In this study, we investigated the potential use of H&E-stained endometrial cancer slide images to predict the associated mismatch repair (MMR) status. H&E-stained slide images were collected from 127 cases of the primary lesion of endometrial cancer. After digitization using a Nanozoomer virtual slide scanner (Hamamatsu Photonics), we segmented the scanned images into 5,397 tiles of 512 × 512 pixels. The MMR proteins (PMS2, MSH6) were immunohistochemically stained, classified into MMR proficient/deficient, and annotated for each case and tile. We trained several neural networks, including convolutional and attention-based networks, using tiles annotated with the MMR status. Among the tested networks, ResNet50 exhibited the highest area under the receiver operating characteristic curve (AUROC) of 0.91 for predicting the MMR status. The constructed prediction algorithm may be applicable to other molecular profiles and useful for pre-screening before implementing other, more costly genetic profiling tests.

The statistical analysis of impact of the top 50 solar flares of X-class (1997-2023) on the global seismic activity, as well as on the earthquake preparation zones located in illuminated part of the globe and in the area of 5000 km radius around the subsolar point was carried out. It is shown by a method of epoch superposition that for all cases the increase of seismicity is observed, especially in the region around the subsolar point (up to 38%) during 10 days after the solar flare in comparison with preceding 10 days. The case study of aftershock sequence of strong M=9.1 earthquake (Su-matra-Andaman Islands, 26.12.2004) after the solar flare of X7.2 class (20.01.2005) demonstrated that the number of aftershocks with magnitude M≥2.5 increases more than 20 times after the solar flare with a delay of 7 days. For the case of the Darfield earthquake (M=7.1, 04.09.2010, New Zealand) it was shown that strong solar flares of class X and M probably triggered two strong aftershocks (M>6) with the same delay of 6 days on the Port Hills fault, which is the most sensitive to external electromagnetic impact from point of view of the fault electrical conductivity and orientation. Based on the obtained results the possible application of natural electromagnetic triggering of earthquakes is discussed for a short-term earthquake prediction using confidently recorded strong external electromagnetic triggering impacts on the specific earthquake preparation zones, as well as ionospheric perturbations due to aerosol emission from the earthquake sources recorded by satellites.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

Every subset S of a Cartesian spaces Rd, endowed with differen- tial structure C∞(S) generated by restrictions to S of functions in C∞(Rd), has a canonical partition M(S) by manifolds, which are or- bits of the family X(S) of all derivations of C∞(S) that generate local one-parameter groups of local diffeomorphisms of S. This partition satisfies the frontier condition, Whitney’s conditions A and B. If M(S) is locally finite, then it satisfies all definitions of stratification of S. This result extends to Hausdorff locally Euclidean differential spaces.

The static formation temperature (SFT) is required to determine the thermophysical properties and production parameters in geothermal and oil reservoirs. However, the SFT is not easy to be obtained by both experimental and physical methods. In this paper, a mathematical approach to predicting SFT based on a new model describing the relationship between bottom hole temperature (BHT) and shut-in time was proposed. The unknown coefficients of the model were derived from least squares fit by Particle Swarm Optimization (PSO) algorithm. Besides, the ability to predict SFT based on a few BHT data (such as first 3, 4, or 5 ones of a data set) was evaluated. The accuracy of the proposed method to predict SFT was testified with a deviation percentage less than ±4% and high values of regression coefficient R² (>0.98). The proposed method could be used as a practical tool to predict SFT in both geothermal and oil wells.

The Na+/K+ ATPase is a protein involved in the active transport of ions across the cellular membrane. Ouabain is a cardiotonic glycoside that, by inhibiting the Na+/K+ pump, interferes with cell processes mediated directly by the pump, but also indirectly influences other cellular processes, such as cellular cycle and proliferation, growth, cell differentiation, angiogenesis, migration, adhesion and invasion. We used the SK-BR-3 breast cancer cell line, mesenchymal stem cells (MSCs), and tumor-associated fibroblasts (TAFs) in vitro for determining the changes induced by Ouabain in concentration of 10-5 M, 10-6 M, 10-8 M, 10-9 M on these cellular types, employing specific methods: SEM for morphological evaluation; immunocytochemistry, flowcytometry to assess immunophenotypical markers expression, cell cycle and Annexin V/PI assay for cellular proliferation and viability testing; flowchamber assay to evaluate functional adhesion behavior; RT-PCR for Na+/K+ ATPase subunits molecular expression. Being indicative of the pro-apoptotic and inhibitory effect of Ouabain on tumor invasion and metastasis, the results support the addition of Ouabain to the oncological therapeutic arsenal, trailing the “repurposing drugs” approach.

(1) The purpose of this study was to compare the percentages of quarterly change for each of the variables analysed (height, weight, body fat percentage and muscle mass) as a function of the quarter in a sample of adolescent football players. (2) The sample consisted of young male football players of different categories belonging to a high-performance football academy, (more than 5 years in football and have spent 1 full year at the academy). (3) Two-way repeated measures ANOVA revealed for the anthropometric variable, P_value

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

Keywords: Innovation ecosystems, Economic sustainability, Hydrocarbon-based economies, Economic diversification, Qualitative approach

In this study, a commercial sodium butyrate protected by a new buffer salt solution (NSB) was tested to determine whether it can be used as an antibiotic alternative in broiler production. 192 1-day-old broilers were randomly allocated to three dietary treatments: soybean meal diet (CON), antibiotic diet (ANT, basal diet + 100 mg/kg aureomycin), and NSB (basal diet + 800 mg/kg NSB). The growth performance, serum anti-inflammatory cytokines, intestinal morphology, gut barrier function, antioxidative parameters, SCFAs content, and cecal microbiota were analyzed. The result showed that NSB significantly improved ADFI, ADG (p < 0.01), and decreased FCR (p < 0.01). Serum anti-inflammatory cytokine IL-10 was up-regulated (p < 0.01), and pro-inflammatory TNF-α was down-regulated (p < 0.05) by NSB supplementation. H&E results showed that VH and VH: CD ratio significantly increased (p < 0.05) in the jejunum and ileum in the NSB group. Furthermore, ZO-1 (p < 0.01), claudin-1 (p < 0.01), and occludin (p < 0.05) in the jejunum and claudin-1 (p < 0.01) and mucin-2 (p < 0.05) in the ileum significantly up-regulated in the NSB group, respectively. Additionally, SOD (p < 0.05) and T-AOC/MDA ratio (p < 0.01) in the jejunum and SOD in the ileum were significantly increased (p < 0.05) in the NSB group. The MDA level also significantly increased (p < 0.01) in the ANT group in the jejunum. Propionic acid (p < 0.05) and butyric acid (p < 0.01) content significantly increased in the NSB group in the jejunum and ileum segments. The 16S rRNA sequencing results showed no significant difference (p > 0.05) in alpha and beta diversity among the groups. LEFSe analysis also indicated that Peptostreptococcaceae, Colidextribacter, Firmicutes, Oscillospira, and Erysipelatoclostridiaceae, which promote SCFA production (p < 0.05), were identified as dominant taxon-enriched bacterial genera in the NSB group. The Spearman correlation analysis revealed that Colidextribacter with ADFI, ADG, VH, claudin-1 (p < 0.05), and unclassified_f__Peptostreptococcaceae with ADFI, IL-10, and ZO-1 were positively correlated (p < 0.05). Furthermore, ADFI and ADG with IL-10, claudin-1, SOD, T-AOC, and butyric acid (p < 0.05), and similarly, ADG with VH (p < 0.05) showed a positive correlation. In conclusion, NSB enhanced the growth performance by improving jejunum and ileum morphology, serum anti-inflammatory cytokines, regulating intestinal barrier function and antioxidant capacity, SCFAs content, and cecum microbiota, showing its potential use as an alternative to antibiotics in poultry nutrition.

Aiming at the development of the application of massive and heterogeneous LEO constellations, the influence of typical perturbation forces on the orbit prediction of LEO satellites at different altitudes is analyzed. Firstly, the main perturbation force model of LEO satellites is introduced. Then experiments for analyzing the influence of orbit prediction on LEO satellites at different altitudes are designed. Finally, the influence of typical perturbation forces on the orbit prediction under different prediction durations by numerical analysis is assessed systematically, and the orbit prediction of LEO satellites with different non-spherical gravitational field orders, ocean tide orders and atmospheric density models were compared and calculated. The research results show that different orders of non-spherical gravitational fields should be considered when the altitude of satellites is different, the reasonable gravitational field orders for LEO satellites at 500km, 1000km, 1500km and 2000km under 1-hour forecast time are 140x140, 80x80, 60x60 and 40x40 orders, the reasonable orders of ocean tide perturbation for 1500km and 2000km satellites are 20x20 orders. Under the 24-hour forecast time, atmospheric resistance has a great influence on the precision of LEO satellites at orbit altitude below 1,000km. The forecast deviation of the LEO satellites orbit at 500km reaches 8751.576m. The difference of orbit precision between different atmospheric density models is in the meter level. The orbit deviation by the Standard Atmosphere 1976 and NRLMSISE 2000 atmospheric models respectively reaches 25.494m. Relevant conclusions provide support for the optimization and selection of dynamical models in high precision orbit determination and fast orbit prediction of LEO satellites.

The present study aims at investigating the relationship between Initial Public Offerings (IPOs) variables mainly underpricing on one hand, and the brand value measures on the other. Our final data set is 104 international brand companies. We implement empirical approach using hierarchical OLS regression and descriptive statistics. We show that underpricing is positively related to brand value which emphasizes the marketing role of going public and underpricing in enhancing brand equity through the product market, which additionally confirms some information asymmetry models. We also find that on average brand companies had not been recognized as brands at the IPO time. Moreover, we show the positive role of private equity in enhancing brand value, additionally, the non-linear association between underpricing and brand value is not evident. Finally, we draw some policy implication and suggestions for future research.

Prolonged ethanol (EtOH) consumption is associated with male infertility with a decreased spermatogenesis rate as one cause. Defective maturation and development of sperm during their storage in the cauda epididymis and transit in the seminal vesicle can be another cause, possibly occurring before the drastic spermatogenesis disruption. Herein, we demonstrated that the cauda epididymis and seminal vesicle of rats, orally fed with EtOH under a regimen that spermatogenesis was still ongoing, showed histological damage, including lesion and decreased height of the epithelial cells, and increased collagen fibers in the muscle layer, which implicated fibrosis. Lipid peroxidation (shown by malondialdehyde (MDA) levels) was observed, indicating that reactive oxygen species (ROS) was produced along with acetaldehyde during EtOH metabolism by CYP2E1. MDA, acetaldehyde and other lipid peroxidation products could further damage cellular components of the cauda epididymis and seminal vesicle and this was supported by increased apoptosis (shown by TUNEL assay and caspase 9/caspase 3 expression) in these two tissues of EtOH-treated rats. Consequently, functionality of the cauda epididymis and seminal vesicle in EtOH-treated rats was impaired, as demonstrated by decreases in 1H NMR-analyzed metabolites (e.g., carnitine, fructose), which were important for sperm development, metabolism and survival in their lumen.

Antisense oligonucleotide (ASO)-mediated exon skipping has emerged as a powerful tool for examining the function of genes and exons in basic research, as well as gene therapy. Computational methods, such as eSkip-Finder, have been developed to predict the efficacy of ASOs via exon skipping using machine learning. However, these methods can be computationally demanding and the prediction accuracy of the tool is not yet optimal. In this study, we propose an approach to reduce computational burden and improve prediction performance by utilizing feature selection within machine learning algorithms and employing ensemble learning techniques. The method was evaluated using a dataset of genes with experimentally validated exon skipping events. The dataset was divided into training and testing sets to assess the accuracy of the algorithm. Our results demonstrate that using a 3-way voting approach with random forest, gradient boosting, and XGBoost can significantly reduce computation time to under ten seconds while improving prediction performance, as measured by R2 for both 2’-O-methyl nucleotides (2OMe) and phosphorodiamidate morpholino oligomers (PMOs). Additionally, the feature importance ranking derived from our approach is in good agreement with previously published results. These findings suggest that this approach has the potential to enhance the efficiency and accuracy of predicting ASO efficacy via exon skipping, facilitating the development of novel therapeutic strategies.

The objective of this study is to evaluate the effect of constitutive equations on the prediction accuracy for springback in cold stamping with various deformation modes. In this study, two types of yield functions—Hill’48 and Yld2000-2d—were considered to describe yield behavior. Isotropic and kinematic hardening models based on the Yoshida–Uemori model were also adopted to describe hardening behavior. Various material tests (such as uniaxial tension, tension- compression, loading-unloading, and hydraulic bulging tests) were carried out to determine the material parameters of the models. The obtained parameters were implemented in the finite element (FE) simulation to predict springback, and the results were compared with experimental data. U-bending and T-shape drawing were employed to evaluate the springback prediction accuracy. Obviously, the springback prediction accuracy was greatly influenced by constitutive equations. Therefore, it is important to choose appropriate constitutive equations for accurate description of material behaviors in FE simulation.

Abstract: Wildfires in forest ecosystems exert substantial ecological, economic, and social impacts. The effectiveness of fire management hinges on precise pre‐fire risk assessments to inform mitigation efforts. This study aims to investigate the relationship between predictions from pre‐fire risk assessments and outcomes observed through post‐fire burn severity analyses. In this study, forest fire risk was assessed with the Fuzzy Analytical Hierarchy Process, in which fire behavior factors were used as input. The degree of burn was determined using the Random Forest method using 11519 training points and 400 test points on Sentinel‐2 satellite images in three different classes. According to the results obtained from 266 selected test points located within the forest boundaries, all primary factors showed an increased effect in areas with high burn severity. Climate, in particular, emerged as the most influential factor, accounting for 52% of the overall impact. However, in cases of high fire severity, climate proved to be the most effective risk factor, ac‐counting for 67%. It followed by topography with 50% accuracy at high fire intensity. In the risk assessment is based on the FAHP method, climate was assigned the highest weight value among other factors with 32.2%. Topography emerged as the second most effective risk factor with 27 %. To evaluate the results more comprehensively both visually and statistically, two regions with different stand canopy characteristics were selected within the study area. While high burn severity had the highest accuracy in Case 1 area, moderate burn severity had the highest in Case 2 area. During the days when the fire continued, the direction of spread was obtained from MODIS images. In this way, the fire severity depending on the direction of fire progression was also interpreted. Through an analysis of various case studies and existing literature, the research underscores both the strengths and limitations inherent in predicting forest fire behavior‐based pre‐fire risk assessments. Furthermore, it emphasizes the necessity of continuous improvement to increase the success of forest fire management.

The group delay response of chirped fiber Bragg gratings (CFBG) written in polarization-maintaining fiber can be measured using the beat spectrum of the reflections from the two polarization axis, with a resolution and reproducibility better than 50 fs. The method is theoretically described, and we analyze the effect of group delay ripples (GDR) on the performance of a stretcher-compressor pair used in chirped pulse amplification systems. Ripples with a spectral period of the order of the pulse bandwidth are the most deleterious. Those are readily captured with our method, despite the limit on resolution due to the fiber polarization beat length. As a rule of thumb, the GDR should not exceed half the pulse duration. The reconstructed phase of the CFBG is also used to predict the pulse compression performance for a given device. Measurement of GDR as low as 161 fs is experimentally demonstrated.

Conventional monitoring relies on "in vivo" (non-destructive) measurements of aboveground organ traits (such as stems, branches, and leaves) to analyze plantation growth trends and assess the effectiveness of management practices like watering and fertilization. This study reveals the necessity of “ex vivo” (destructive) approaches, post-excavation, to ensure fully reliable monitoring of plantation performance, including belowground organ growth and development trends. We showcase the effectiveness of dendrometric analysis, which measures the annual ring width in the secondary xylem (wood) of the taproot and stem. Monitoring above- and belowground organ growth trends allow for the exploration of similarities and differences in how different tree organs respond to internal and external factors. Such monitoring is especially crucial for assessing plantation performance in challenging climates, such as those found in arid and semi-arid lands.

Proteins play a pivotal role in supporting athletes by promoting muscle hypertrophy and minimizing protein catabolism during exercise. They stimulate muscle protein synthesis, aiding in the repair of exercise-induced muscle damage and serving as an energy source, particularly for post-exercise glycogen replenishment. In individuals with phenylketonuria (PKU), for whom protein intake is limited to essential phenylalanine (Phe), supplementation with Phe-free amino acids or glycomacropeptides is necessary. Tailored for macronutrient and micronutrient content, these protein substitutes fulfill most protein requirements, but lack Phe, unlike dietary sources of protein. Protein requirements for athletes with PKU exceed general recommendations due to limited availability in supplements and potential catabolism mitigation. Various factors influence tolerated dietary Phe in PKU, including protein substitute quantity, distribution, pharmacological treatment, age, growth rate, pregnancy, catabolic states, and physical activity. While general protein requirements for PKU surpass those of the general population, adherence to supplement regimens is crucial for athletes and patients with PKU. Strategically timed protein substitutes enhance muscle protein synthesis, body composition, and sports performance within safety limits. Individualized intake is essential for optimal outcomes, as proteins have a multifaceted role in optimizing athletic performance and addressing challenges in PKU.

This paper explores the views of a group of young men aged 16–18, studying towards a Level 1 diploma in music in the North East area of England. It uses the conceptualization of “social haunting” to focus our discussions about how Level 1 learners articulated their experiences in the context of their learning journeys and perceived marginalization. The research took place at a large Further Education (FE) college and included a series of five “research encounters” with the group of Level 1 learners. These encounters included a range of activities, resulting in a variety of data being collected, including several activity worksheets, structured and unstructured focus group interviews, and questionnaires. This paper focusses on the outcomes of a single research activity that focused on exploring the topic of marginalization. We present a discussion on social haunting as one of the emerging findings from this research encounter, outlining how the reality of the social and cultural legacy of the UK’s industrial past can shape today’s youth and their futures. We will talk about the young men’s views of marginalization, their school-to-work transitions, the formation of masculinity in post-industrial communities and the role of Further Education in it. The paper concludes by discussing some insights for practice and future research.

We will apply Pascal’s hydrostatic pressure law to black holes and also to the Hubble sphere. Haug has recently demonstrated how hydrostatic pressure in water can be utilized to determine the Planck length. One can conceptualize the energy in the Hubble sphere as a type of superfluid, and if this is correct, then Blaise Pascal’s hydrostatic pressure formula may also be applicable to such a superfluid, even within the Hubble sphere. By employing the same method on the Hubble sphere and considering it as a Schwarzschild black hole with the critical Friedmann mass, we can estimate the Planck length based on its hypothetical hydrostatic pressure.

Distracted driving is a major cause of road traffic crashes in Yaoundé. Partly due to scarcity of enforcement, lack of evidence and investigation of distraction safety performance indicator (SPI), hindering evidence-based intervention. This study aimed to address this evidence gap by evaluating the distraction SPI using proven methodology. Data on distracted driving (handheld mobile device; interaction; eating/smoking/drinking) were collected from roadside observation on 36 randomly selected road sections carefully spread to cover the city. SPI were computed and weighted with traffic volume to ensure representativeness of values. A total of 41,004 drivers were observed (38,248 in car; 1,116 in van; 977 in truck; 663 in bus). The prevalence of distracted driving in Yaoundé is 13.69% for the three distractions type combined. The prevalence is 7.84% for interaction, 4.89% for handled mobile device usage and 0.96% for eating/smoking/drinking. Leveraging these insights, a seven year (2024 - 2030) fighting strategy aiming at halving the prevalence was developed. The strategy contains intervention including on legislation/enforcement, which have been proven effective. This study, pioneer in Yaoundé, provide stakeholders with evidence of the issue and measures to implement and can also serve when developing road safety strategy.Future research should consider investigation at national level.

In Yaoundé, Cameroon, excessive and inappropriate speeding remains a major public health concern. Part of the problem are the unsafe speed limits, lack of evidence, and effective evaluation of speeding safety performance indicators (SSPIs), and the absence of speed management, hindering the city's ability to mitigate the risks associated with speeding. This study aimed to address this knowledge gap by assessing SSPIs using a well-defined methodology and suggesting speed management strategies. Data on speed, traffic volumes and road attributes were collected from a random selection of 16 representative road sections in Yaoundé. Seven SSPIs were calculated, and weights were assigned to evaluate city-level SSPIs. The findings showed that 66.8% of drivers drive within the speed limit, generally operating at speeds of 54 km/h with a speed variation of 26 km/h. Based on the speed analysis, evidence-based strategies are proposed, and implementing these strategies could potentially reduce fatalities and serious injuries by 16% to 84% across study locations, as indicated by Elvik's model. These findings have significant policy implications for reducing speeding in Yaoundé, and the methodological approach can be replicated in other urban settings. Future research should extend SSPI evaluation to the national level and test the effectiveness of the recommended strategies.

This retrospective study aimed to evaluate the performance of the hormone treatment protocols, determine the factors associated with pregnancy success after hormone treatment, and compare the cost-efficiencies of two types of hormone treatment among cyclic and noncyclic anestrous dairy cows. The clinical records of 279 anestrous cows who received hormone treatment for artificial insemination (AI) from 64 herds in the western region of Thailand were obtained from Kasetsart University Veterinary Teaching Hospital from January to August 2017. The performance of the hormone treatment protocols, fixed-time AI (TAI) and estrus detection before AI (EAI), showed that the pregnancy risk for the TAI protocol was higher than for the EAI protocol, but pregnancy per AI did not differ significantly between the two protocols in cyclic and noncyclic cows. Multivariate logistic regression analysis showed that cows receiving the TAI protocol were more likely to be pregnant compared to those treated with the EAI protocol. Cows with a 3.00 body condition score (BCS) &lt;3.75 after treatment and loose-housing cows were more likely to become pregnant. Treatment during winter showed higher pregnancy success than in the summer and rainy seasons. The cost-efficiency analysis showed that the TAI protocol was the most cost-efficient option for noncyclic cows, whereas the EAI protocol was the most cost-efficient option for cyclic cows.

In the field of delta-sigma modulators, reducing system power consumption without sacrificing accuracy has become a challenge. The summing circuit, as the main part of the cascade-of-integrator-in-feedforward delta-sigma modulator, consumes a significant amount of power in active summing. On the other hand, passive summing circuits have low power consumption but can cause attenuation in the summing results. This article proposes a low-power multi-bit delta-sigma modulator based on passive and attenuationless summation scheme. The summation circuit achieves multiplication of the voltage signal carried on the summation capacitor through bidirectional sampling technique, compensating for the inherent attenuation caused by passive summation, thus eliminating the need for active OTA to achieve perfect summation. A 2-order delta-sigma modulator based on 4-bit 1-order passive noise-shaping (NS) SAR quantizer is designed to verify the scheme. By combining a passive NS SAR as the 4-bit quantizer and the third-stage integrator of the system, and incorporating an energy-efficient cascode floating inverter amplifier (FIA) structure as the core active OTA, these elements have significantly enhanced the energy-efficiency of the modulator. Simulation results show that at a supply voltage of 1.2 V and a bandwidth of 20 kHz, the SNDR reaches 102.62 dB, power consumption is only 148.32 μW, and Schreier figure-of-merit (FoM) of SNDR is 183.92 dB.

Dirac's Large Number Hypothesis (LNH), proposed in 1937, has captivated the scientific community with its exploration of profound correlations between cosmic and atomic scales. This hypothesis delves into the intricate interplay between the infinitesimally small and the vastly large, offering potential insights into the fundamental nature of the universe. As we continue to uncover the mysteries of the cosmos, the LNH oscillates on the precipice of scientific acceptance—neither fully validated nor entirely dismissed. In this review paper, we embark on a comprehensive journey through Dirac's LNH, shedding light on its theoretical underpinnings, its implications for universe models, and its resonance with the Anthropic Principle. We delve into the possibilities of variable gravitational constants and continuous mass creation, inviting further exploration into the intricacies of our cosmic symphony. By embracing the ongoing quest for understanding, we endeavor to unravel the profound harmonies that connect the infinitesimal with the infinite, contributing to the symphony of knowledge in theoretical physics and cosmology.

3D printing is a non-traditional additive manufacturing process. It is different from the traditional subtractive manufacturing process. It offers exceptional rapid prototyping capabilities and results that traditional subtractive manufacturing methods cannot attain, especially in applications involving curved or intricately shaped components. Despite its advantages, metal 3D printing will face porosity, warpage, and surface roughness issues. These issues will affect the future practical application of the parts indirectly, for example, the structural strength and the parts assembly ca-pability. Therefore, this study compares the qualities of the warpage, weight, and surface rough-ness after milling and grinding processes under the same materials (316L stainless steel) between general rolled steel and 3D additive steel. Experimental results show that 3D printing parts are approximately 13% to 14% lighter than the general rolled steel. The surface roughness performance of 3D printing steel is better than general rolled steel under the same material after milling or grinding processing. The hardness of the 3D printing steel is better than that of the gen-eral rolled steel. The research verifies that 3D additive manufacturing can use surface processing to optimize surface performance and achieve the functions of lightness and hardness.

Aim: the main aim of this study is to compare the onset of effectiveness of mental nerve block with lingual infiltration and inferior alveolar nerve block on patients visiting dental hospital for extraction of mandibular anterior teeth. Materials and methods: The study was set in a clinical setting. This was a randomized controlled double-blind cross study, where 25 subjects received two treatments at an interval of at least 1 week in a within a dental hospital.Inferior alveolar nerve block and lingual nerve block injection is given with 2mL lignocaine 2% with 1:2,00,000 epinephrine was administered for the right side. Mental nerve block along with lingual infiltration of the corresponding tooth was given with 2mL lignocaine 2% with 1:2,00,000 epinephrine was administered on the left side.Visual analogue scale (VAS) was used in this study, which consists of a scale with range of 0-10 pain severity on which 0 indicated absence of pain and 10 the worst pain possible. The patients were asked to give scores corresponding to his/her pain, after IANB, mental nerve block and lingual infiltration and these scores were recorde.Results: From the results we can see that patients gave scores between 3-4, stating that they had moderate pain during extraction after administration of IANB (54%) (graph 2) and VAS scores of 0-1 were given by patients, which is suggestive of no pain during extraction after administration of Mental nerve block and lingual nerve infiltration (62%)Conclusion: Within the limits of the study we can conclude that mental nerve block along with lingual infiltration is an effective way to completely and quickly anaesthetise the central incisor to the 1st premolar region.

In this work, we report the electric energy storage properties of (1-x)Bi0.5(Na0.8K0.2)0.5TiO3-xBi0.2Sr0.7TiO3 (BNKT-BST; x = 0.15-0.50) relaxor ferroelectric ceramics enhanced via a domain engineering method. A rhombohedral–tetragonal phase, the formation of highly dynamic PNRs, and a dense microstructure are confirmed from XRD, Raman vibrational spectra, and microscopic investigations. The relative dielectric permittivity (2664 at 1 kHz) and loss factor (0.058) were gradually improved with BST (x=0.45). The incorporation of BST into BNKT can disturb the long-range ferroelectric order, lowering the dielectric maximum temperature Tm and inducing the formation of highly dynamic polar nano-regions. In addition, the Tm shifts toward high temperature with frequency and a diffuse phase transition, indicating relaxor ferroelectric characteristics of BNKT-BST ceramics, which is confirmed by the modified Curie Weiss law (γ=1.83). The rhombohedral–tetragonal phase, fine grain size, and lowered Tm with relaxor properties synergistically contribute to a high recoverable energy density Wrec of 0.81 J/cm3 and a high energy efficiency η of 86.95% at 90 kV/cm for x = 0.45.

The effectiveness of combining strength-specific training with endurance training to enhance the performance of endurance runners remains uncertain. This study aimed to analyze effect of practising maximum-strength (MAX), explosive strength (EXP) or both combined (COMB) on seven runners’ performance-indicators: vertical jump (VJ), one-repetition-maximum-squat (1RM), peak-velocity/peak-running-speed (PV), lactate-threshold (over incremental-test-protocols, LT), middle-distance-time-trial (TT), maximum-oxygen-consumption (VO2max), running-economy (RE). Systematic-review (Scopus, Wed of Science, Sports Discuss, PubMed) with meta-analysis was conducted following PRISMA standards. Inclusion-criteria (PICOS) were: recreational or well-trained athletes aged 18-45 performing concurrent-training ≥five-week. Used search-terms were related to different types of strength/endurance, participants’ age, sport-modality. 20 manuscripts were selected, quality-assessed with PEDro. MAX training is more effective than EXP, COMB in improving VJ, 1RM, PV, while COMB is more effective than MAX, EXP to enhance TT. MAX is more effective than EXP in improving LT. Concurrent-workouts do not provide additional benefits to VO2max. It is unknown which strength-modality (MAX, EXP or COMB) is more effective in improving RE. Concurrent-training is more effective than single-mode-endurance-training for enhancing specific performance-variables in adult-endurance-runners. Middle-, long-distance-runners may consider incorporating MAX-training to target specific goals, e.g., improving VJ, 1RM, LT, PV while utilizing COMB-training to enhance TT. Certain variables may benefit from EXP. New randomized-controlled-trials are required to confirm these findings.

(1) Background Diabetic Retinopathy (DR) is the primary cause of poor vision in young adults. Screening for DR is important but many patients do not attend; (2) Methods: We validated an algorithm for predicting DR and its progression by conducting a retrospective study of 11 children in a population of 120,389 T2DM (3) Results: By applying the algorithm to the population showed an AUC of 0.93 (95% CI, 0.92–0.94) for any-DR and 0.90 (95% CI, 0.89–0.91) for referable-DR(4) Conclusions: The algorithm is useful for predicting patients who could develop referable forms of DR and also for any-DR. This would allow a personalized screening plan to be drawn up for each patient.

Sweat rate and electrolyte losses have a large inter-individual variability, a personalized approach to hydration can overcome this issue to meet an individual’s needs. This study aimed to investigate the effects of personalized hydration strategy (PHS) on fluid balance and intermittent exercise performance. Twelve participants conducted 11 laboratory visits including a VO2max test and two 5-day trial arms under normothermic (NOR) or hyperthermic (HYP) environmental conditions. Each arm began with 3-day of familiarization exercise following by two random exercise trials with a either PHS or control (CON). Then, participants crossed-over to the second arm for: NOR+PHS, NOR+CON, HYP+PHS, and HYP+CON. The PHS was prescribed according to participants’ fluid and sweat sodium losses. CON drank ad-libitum of commercially-available electrolyte solution. Exercise trials consisted of two phases: 1) 45min constant workload; 2) high-intensity intermittent exercise (HIIT) until exhaustion. PHS had a significantly greater fluid intake compared to CON. HYP+CON produced the lowest sweat sodium concentration. HYP+PHS had a lower thirst perception and a longer HIIT compared to HYP+CON. Thus, PHS reinforces fluid intake and successfully optimizes hydration status, regardless of environmental conditions. PHS may be or is an important factor to preventing negative physiological consequences during high-intensity exercise in the heat.

The mesoporous heteroatom molecular sieve MCM-41 bulk crystals with the crystalline phase were synthesized via a one-step hydrothermal method using an ionic complex as template. The ionic complex template was formed by interaction between cetyltrimethylammonium ions and metal complex ion [M (EDTA)]2- (M=Co or Ni ). The materials were characterized by X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, N2 adsorption–desorption isotherms, and X-ray absorption fine structure spectroscopy. The results showed that the materials possess a highly ordered mesoporous structure with the crystalline phase and possess high uniform ordered arrangement channels. The structure is in the vertical cross directions with a crystalline size of about 12 µm and high specific surface areas. The metal atoms were incorporated into the zeolite frameworks in the form of octahedral coordinate and have a uniform distribution in the materials. The amount of metal complexes formed by metal ion and EDTA is an essential factor for the formation of the vertical cross structure. Comparing to Si-MCM-41, the samples exhibited better conversion, higher selectivity for cumene cracking.

The objective of this study was to evaluate the efficacy of fungal treatment (Pleurotus ostreatus) of urea-treated rice stubble on growth performance in slow-growing goats. Eighteen crossbred Thai native x Anglo-Nubian male goats (average body weight: 20.4 ± 2.0 kg) were randomly assigned to three experimental total mixed rations containing 35% rice stubble (RS) that was either untreated (URS), urea treated (UTRS) or treated with urea and fungi (UFTRS). URS and UTRS were cultivated and harvested from aseptically fungal spawn, incubated at 25-30 °C for 25 days. Indicators of growth performance were monitored and faeces were collected quantitatively to assess nutrient digestibility, during a 12-week feeding trial. All goats remained healthy throughout experiment. The goats fed UFTRS had a lower feed conversion ratio (kg feed/kg growth) compared to goats fed URS or UTRS. Compared to URS, dietary UFTRS increased nutrient digestibility of slow-growing goats, such as OM (+8.5%), CP (+5.5%), NDF (+39.2%), and ADF (+27.4%). Likewise, dietary UFTRS tended to increase rumen ammonia concentrations but rumen pH and volatile fatty acids were not affected by UFTRS. In conclusion, the present study indicates that the fungal treatment of RS is an effective tool to improve the growth performance of slow-growing goats.

This study addresses the urgent need for sustainable protein sources in aquaculture due to the depletion of marine resources and rising costs. Animal protein sources, particularly poultry by-product meal (PBM) and insect exuviae meal, are investigated as viable alternatives to fishmeal (FM). Research confirms the successful replacement of FM with a combination of PBM and insect exuviae meal (up to 50%) in the diet of European seabass without compromising growth, feed conversion, gut health and liver fat content. In particular, growth performance was robust with both PBM formulations, with the 25% PBM diet showing better results. Histological examinations showed good gut and liver health, contradicting the concerns of previous studies. The study emphasizes the importance of holistic analyzes that go beyond growth parameters and include histomorphological investigations. The results show that PBM in combination with insect/exuviae meal is well tolerated by seabass, which is consistent with literature reports of mitigating negative effects on gut health. A detailed analysis of the microbiota revealed a decrease in the Firmicutes/Proteobacteria ratio due to an increase in potentially pathogenic bacteria. However, the formulation containing insect exuviae partially counteracted this effect by preserving the beneficial Lactobacillus and promoting the synthesis of short-chain fatty acids (SCFA), particularly butyrate. Chitin-rich components from insect exuviae were associated with improved gut health, which was supported by increased production of SCFA, which are known for their anti-inflammatory properties. The study concludes that a combination of PBM and insect/exuviae meal can replace up to 50% of FM in the diet of seabass, supporting sustainable aquaculture practices. Despite some changes in the microbiota, the negative effects are mitigated by the addition of insect exuviae, highlighting their potential as a prebiotic to increase fish productivity and contribute to a circular economy in aquaculture.

The ability to predict the skin sensitization potential of small organic molecules is of high importance to the development and safe application of cosmetics, drugs and pesticides. One of the most widely accepted methods for predicting this hazard is the rodent local lymph node assay (LLNA). The goal of this work was to develop in silico models for the prediction of the skin sensitization potential of small molecules that go beyond the state of the art, with larger LLNA data sets and, most importantly, a robust and intuitive definition of the applicability domain, paired with additional indicators of the reliability of predictions. We explored a large variety of molecular descriptors and fingerprints in combination with random forest and support vector machine classifiers. The most suitable models were tested on holdout data, on which they yielded competitive performance (Matthews correlation coefficients up to 0.52; accuracies up to 0.76; areas under the receiver operating characteristic curves up to 0.83). The most favorable models are available via a public web service at https://nerdd.zbh.uni-hamburg.de/skinDoctor/ that, in addition to predictions, provides assessments of the applicability domain and indicators of the reliability of the individual predictions.

Introductions- Liveable housing environments face the menace of global climate change. In-frastructure (including buildings and houses) continuously experiences significant impacts ex-acerbated by natural variability in climate. The study addressed how climate change impacts the resilience of residential buildings, increased maintenance frequency, and the wellbeing and comfort of residents in UK residential buildings. Design/Methodology/Approach: This study used deductive reasoning and an empirical epis-temological methodology as a data-collecting basis to evaluate primary information obtained via a questionnaire. Regression analysis was ultimately employed to analyse the collected da-ta. Result/Discussions: The findings show a significant relationship between climate change and the wellbeing of the occupants of UK residential buildings. Also, the results show that social wellbeing is more important to the occupants than mental and physical wellbeing. It reveals that residential buildings in the UK suffer the cost of maintenance due to continuous reduc-tion in the building fabric's resilience to the impacts of climate change; for instance, a recent increase in rainfall/storms results in unprecedented flooding, which continues to damage the UK residential building fabrics.

Individuals with BPD grapple with unstable relationships, marked by extreme emotional swings and interpersonal conflicts. Emotional instability, a distorted self-image, and impulsivity further complicate matters, often leading to self-harm and suicide attempts as desperate coping mechanisms. Genetics and adverse childhood experiences contribute to BPD's development, shaping brain function and emotional regulation. Diagnosis involves meticulous assessments, paving the way for personalized treatments like dialectical behavior therapy and, in severe cases, hospitalization. Early intervention, professional support, and societal understanding are pivotal for positive outcomes, and challenging mental health stigma.

In order to the effect of hydrated phase change materials on suppressing coal spontaneous combustion, the thermogravimetric experiment and reaction activation energy analysis experiment were used to explore the changes of combustion characteristic, parameters characteristic temperature and activating energy of gas coal, long flame coal, meagre coal, and lean coal before and after adding hydrated phase change materials. The research results showed that hydrated phase change materials increased the coal samples’characteristic temperature point and have effective inhibitory effects on different stages of oxidation process.However, the effect was best at low temperatures, as hydrated phase change materials undergo phase change and absorb heat when heated at low temperatures, isolating coal from contact with oxygen. The activating energy increased by 1.138 KJmol-1～23.048 KJmol-1 and the mass loss reduced by 1.6%～9.3% after the inhibition of the coal sample,indicating that the oxidation rate of various coal samples can be slowed down and the spontaneous combustion can be suppressed by using hydrated phase change materials.At the same time, this material can also reduce the combustibility index of meagre coal and lean coal, as well as the comprehensive combustion index and maximum loss rate of long flame coal and gas coal.

This review explores the transformative impact of sensor technologies in early disease detection. It highlights recent advancements in nanotechnology-based sensors, particularly focusing on their applications in identifying disease biomarkers at early stages. The integration of these sensors with artificial intelligence for predictive analytics in healthcare is also discussed. Applications in cancer, infectious diseases, and chronic disease management underscore their diverse utility. Challenges in sensor technology adoption and future directions, including multiplexed sensors and wearable devices, are examined. This review underscores sensors' potential in enhancing disease management and patient outcomes.

Legumes develop root nodules that harbour endosymbiotic bacteria, rhizobia. These rhizobia convert nitrogen to ammonia by biological nitrogen fixation. A thorough understanding of the biological nitrogen fixation in legumes and its regulation is key to develop sustainable agriculture. It is well known that plant hormones affect nodule formation; however, most studies are limited to model legumes due to their suitability for in vitro, plate-based assays. Specifically, it is almost impossible to measure the effects of exogenous hormones or other additives during nodule development in crop legumes such as soybean as they have huge root system in soil. To circumvent this issue, the present research develops suitable media and growth conditions for efficient nodule development under in vitro, soil free conditions in an important legume crop, soybean. Moreover, we also evaluate the effects of all major phytohormones during soybean nodulation under identical conditions. This versatile, inexpensive, scalable and simple protocol provides several advantages over previously established methods. It is extremely time-and resource-efficient, does not require special training or equipment, and produces highly reproducible results. The approach is expandable to other large legumes as well as for other exogenous additives.

Enhancing energy efficiency within the building sector is imperative to curbing energy losses, given that this sector alone contributes to over 34% of global energy consumption. Employing a building management system, along with its regular updates, presents a strategic avenue to decrease energy usage, enhance building energy efficiency, and more. Tailored control strategies, aligned with the unique characteristics and usage patterns of each building, are essential for achieving energy savings. This article presents an evaluation of HVAC system efficiency in office buildings, utilizing a data-driven approach coupled with simulations conducted in IDA ICE software. The research explores the control strategy of an office building equipped with a constant air volume HVAC system, featuring a regularly controlled air handling unit. The objective is to boost energy efficiency while striking a balance between occupant comfort and energy consumption. Findings indicate that by analyzing measured data and adjusting configurable parameters, building energy consumption can be significantly reduced. Close monitoring of indoor parameters by building operators and corresponding adjustments to the HVAC system can yield energy savings of up to 16%. Leveraging these insights, the paper suggests integrating data-driven and dynamic simulation methods into building management system models to optimize HVAC systems, enhance energy efficiency, and advance ambitious carbon neutrality objectives.

Educational institutions must identify students who are academically struggling to provide them with necessary support to improve their performance. In this context, recommendation systems powered by deep learning techniques are vital for detecting and categorizing such students. These systems help students plan their future by uncovering patterns in their historical academic data. This study introduces a new deep learning model designed to classify academically underperforming students in educational settings. The model incorporates a Gated Recurrent Neural Network (GRU) and includes specific neural network features like a dense layer, max-pooling layer, and the ADAM optimization algorithm. The model's training and evaluation were conducted using a dataset comprising 15,165 student assessment records from various academic institutions. The performance of the developed GRU model was benchmarked against other educational recommendation systems, including Recurrent Neural Network models, AdaBoost, and the Artificial Immune Recognition System v2. The proposed GRU model demonstrated remarkable accuracy, achieving an overall rate of 99.70%.

In the present study. At first, some properties of r-fuzzy soft β-closed sets are introduced on fuzzy soft topological spaces based on the paper Aygunoglu et al. (Hacet. J. Math. Stat. 2014, 43, 193-208). Also, we define the closure and interior operators with respect to the classes of r-fuzzy soft β-closed and r-fuzzy soft β-open sets, and investigate some of their properties. In addition, the concept of r-fuzzy soft β-connected sets is introduced and characterized with help of fuzzy soft β-closure operators. Thereafter, some properties of a fuzzy soft β-continuity are studied. Furthermore, we introduce and study the concepts of fuzzy soft almost (weakly) β-continuous functions, which are weaker forms of a fuzzy soft β-continuity. Also, the relationships between these classes of functions are specified with the help of some illustrative examples. Finally, we explore new types of fuzzy soft functions called, fuzzy soft β-irresolute (strongly β-irresolute, β-irresolute open, β-irresolute closed and β-irresolute homeomorphism) functions, and discuss some properties of them. Also, we show that fuzzy soft strongly β-irresolute → fuzzy soft β-irresolute → fuzzy soft β-continuity, but the converse may not be true.

This work proposes a hollow-core photonic crystal fiber-based edible oil sensor in the terahertz (THz) range (e.g., 1.0THz ≤ f ≤ 3.0THz) and different sensing characteristics are numerically analyzed. The suggested sensor’s performance was assessed by means of COMSOL Multiphysics, a commercial program that uses the finite element approach. The computational results indicate that the relative sensitivity is 85.591%, 84.648%, 82.625%, 82.683%, and 79.161%, respectively, at f = 2.2 THz, for several types of sunflower oil, mustard oil, coconut oil, olive oil and palm oil; and the corresponding effective areas are 7.22×10-8 um2, 7.09×10-8 um2, 6.83×10-8 um2,7.09×10-8 um2, 6.5231 ×10-8 um2. In addition, the effective material loss for sunflower oil, muster oil, coconut oil, olive oil, and palm oil has been found to be 0.02561 cm-1, 0.027054 cm-1, 0.030322 cm-1, 0.028854 cm-1 ,0.035427cm-1 respectively. Moreover, the proposed sensor also has low confinement loss are 1.55×10-8 dB/m, 1.63×10-8 dB/m, 1.31×10-8 dB/m, 1.99×10-8 dB/m, 4.0345×10-8 dB/m.This proposed sensor can be fabricated using extrusion and 3D-printing technologies, and due to its augmented detecting capabilities, it can be a vital part of oil sensing devices implemented in real life such as industry fields.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

This study offers a concise summary of the research that has been done on alternative methods of HRM. A survey of 47 articles on the topic of creative human resource management uncovered three primary schools of thinking. At its core, innovation in HRM entails nothing more than that. One such topic worthy of investigation is the way human resource management approaches new situations. Third, research on inventiveness in the business world has given rise to the concept of "innovative HRM." Each of these three approaches, as well as the theoretical underpinnings of each, will be covered in this article. The note wraps up with a discussion of the significance of the findings for next research as well as clinical practice.

In this paper, it is defined that how the IPOs are affected by the underwriter reputation. What will happen to IPOs who are backed by reputed underwriter and who is not? And evaluate the IPOs short-run and long-run performance. Also try to explain the relationship between IPOs and underwriter. Also tried to compare some of the international return and Pakistani returns. Also determine the relation of the investor to the underwriter. There is a set of investors who have there own relationship with the underwriters how they will affect on the IPOs in the market.

Over recent years, the swine industry has witnessed the withdrawal of antibiotics and continuous regulation of zinc and copper oxides in the early-life nutrition of piglets. Due to this development, alternative ingredients or additives from plant sources have been tremendously explored. Therefore, this study's objective was to evaluate the effect of dietary supplementation with tannins on weaned piglets’ growth performance, serum antioxidant capacity, and immune status using a meta-analysis approach. With only the inclusion of non-challenged weaned piglets, a total of 16 studies with parameters of interest were deemed eligible after a two-step screening process following a comprehensive literature search in the scientific databases of Web of Science, Scopus, ScienceDirect, PubMed, and Google Scholar. Two main categories of data, including the study’s characteristics and response variables (growth performance, serum antioxidant, and immune indices), were extracted. Applying the random-effects models, Hedges’ g effect size of supplementation with tannins was calculated using the R software to determine the standardized mean difference (SMD) at a 95% confidence interval. Sub-group analysis and meta-regression further explored heterogeneity (PSMD 0.05, I2 50%, n ≥10). Supplementation with tannin reduced average daily gain (p = 0.20) and feed conversion ratio (p 0.01); however, it increased average daily feed intake (p = 0.07) and final body weight (p 0.01). Meta-regression models indicated that tannin dosage and supplementation duration were directly associated with tannins' effectiveness on productive performance. In the serum, the concentration of glutathione peroxidase, superoxide dismutase, and total antioxidant capacity were elevated (p 0.01) in response to tannins supplementation, while malondialdehydes was reduced (p 0.01). Likewise, decreased immunoglobin A (p = 0.47) and increased immunoglobin M and G levels (p 0.01) were detected. In conclusion, dietary supplementation with tannins, particularly with chestnut and grape seed proanthocyanidins, increases the productivity of weaned piglets. At the same time, it is a possible nutritional strategy to mitigate oxidative stress and stimulate gut health. Thus, supplementing chestnut and grape seed proanthocyanidin tannins in the early phase of swine production could be used to alleviate the incidence of diarrhea.

The present minireview assessed the benefits of using artificial intelligence applications in healthcare at predicting the targets of bioactive small molecules in human. Method. The tool is a tuned algorithm, with novel data in web interface. Results. We used tables to order the information of Swiss Target Prediction that allow predictions on combination of chemotherapies and probable side effects. This tool is useful to understand the molecular mechanisms underlying a given phenotype or bioactivity, to rationalize possible favorable or unfavorable side effects and to predict off-targets of known molecules as well as to clear the way for drug repurposing. Predictions are done using a ligand-based approach to compare the similarity between a query molecule and the known ligands of a large collection of protein targets. Conclusion. This study allowed us to formulate recommendations for the use of some of the chemotherapeutic agent groups in cancer patients at a low cost. It is very important and beneficial for patients that take medicine for a longer period and on whose lives depend on such treatment.

The following article presents an analysis of the determinants of diabetes using a dataset containing the surveys of 2000 patients from the Frankfurt Hospital in Germany. The data were analyzed using the following models, namely: Tobit, Probit, Logit, Multinomial Logit, OLS, WLS with heteroskedasticity. The results show that the presence of diabetes is positively associated with "Pregnancies", "Glucose", "BMI", "Diabetes Pedigree Function", "Age" and negatively associated with "Blood Pressure". A cluster analysis is realized using the fuzzy c-Means algorithm optimized with the Elbow method and three clusters were found. Finally a confrontation among eight different machine learning algorithms is realized to select the best performing algorithm to predict the probability of patients to develop diabetes.

Abstract: In the Western of Mekong Delta belong to Vietnam a amount of alluvium sediments flows from upstream China to Vietnam, they are going from the river branches to in the Mekong Delta, then get out the Western Sea of Vietnam. This sediments accumulated gradually elevation the new land. The increase elevation of the land creates a fertile coastal plain where mangrove forests with a rich ecosystem of plants and animals. Over time, these forests change, with different plant species succeeding each other. This aims of this study to finding plant species in the forest, classification of forest types based on ecological regions, assessement the biodiversity of tree species, and compare the abundance communities, measuring the growth of the forest in these regions. In 2023, a comprehensive survey was conducted by using a systematic approach. The number of survey plots have done depend on the density of the forest, Base on the width of the forest range, the number of survey plots from 500m to 1,000m set up 1-2 plots, sub region set up from 10 to 15 plots. In total, 68 plots have done established in the erea, the area of plot is 100 square meters (10m x 10m). Using the statistical software in forestry to survey and analysis data. The result provided a complete picture of the tree species composition, distribution, and community structure characteristics in each ecological sub-region. The result of survey showed in the sub-region 1 have seven species as Sonneracia ovate, Rhzophora apiculata, Excoecaria agallochha, Avicennia officinalis, Avicennia alba, Agricerasvcoculatum, Bruguiera gymnorhiza. In the sub region 2 have eleven species as Sonneracia caseolaris, Annona reticulata, Lumnitzera littorea, Lumnizera racemosa, Rhizophora apiculata, Excoecaria agallocha, Avicennia officinalis, Avicennia alba, Hibiscus tillacerus, Bruguiera gymorhiza, Aericeras comiculatum. In the sub region 3 have eight as Sonratia caseolaris, Rhizophora mucronata, Rhizophora apiculata, Excoecaria agallocha, Avicennia marine, Avicennia alba, Bruguiera gymorhiza. In the region 4 have ten species as Sonneracia caseolaris, Sonneracia ovate, Lumnizera racemosa, Rhizophoa apiculata, Excoecaria agallocha, Avicennia marina, Avicennia officinalis, Aviecnnia alba, Bruguiera gymorhiza, Bruguiera cylindrica The total species of the mangrove forest in the Western Mekong Delta have 16 species from 11 plant families have been identified. Among these species have 6 dominant species include Avicennia oficinali),Avicennia alba, Rhizophora apiculata, Excoecaria agallocha, Someratia caseolaris, and Bruguiera yipamoriza. Two species easy grow on the new land are Avicennia officinalis Avicennia alba this findings show they can develope on the original new land for the shore of the Western Mekong Delta. The surveyed results also calculated the average of the height, diameter (D1.3), canopy, health of the nature mangrove tree for each sub region and total region. From these results showed the division of foresty structure, the structure of height, diameter (D1.3), canopy, vitality of the sub region and total region in the Western Mekong Delta.

Ambrosia trifida is a kind of malignant invasive plant, which has very high reproductive and en-vironmental adaptability. Through strong resource acquisition ability and allelopathy, it could inhibit the growth and reproduction of surrounding plants, destroy the stability of an invasive ecosystem. It is very important to predict the change of suitable distribution area of Ambrosia trifida with climate change before implementing scientific control measures. Based on 106 Ambrosia trifida distribution data and 14 environmental data, the optimal parameter combination (RM = 0.1, FC = LQ) was obtained by using the MaxEnt model optimized by Kuenm package, the potential suit-able areas of Ambrosia trifida in Northeast China under three different climate scenarios (RCP2.6, RCP4.5, RCP8.5) with different emission intensities in the future (2050,2070) were predicted. The changes of Ambrosia trifida suitable area in Northeast China under three climate scenarios were compared, and the relationship between the change of suitable area and emission intensity was analyzed. In general, the suitable area of Ambrosia trifida in Northeast China will expand gradually in the future, and the area of its highly suitable area will also increase with the increasing emission intensity, which is unfavorable to the control of Ambrosia trifida.

This aim of this study was to investigate the relationships between lifestyle factors, insulin resistance, and male fertility in 73 men with and without insulin resistance. The participants were divided based on insulin resistance status. Their physical activity, diet, perceived stress, sleep quality, libido level, and the duration of sexual abstinence were assessed on the basis of a number of parameters, including indices proposed by the authors. The results highlighted associations between a number of parameters, i.e., micronutrient and vitamin intake, diet quality, body composition, insulin resistance, and the duration of sexual abstinence, and semen quality, as measured by sperm motility. Significantly, the presence or absence of insulin resistance was linked to male fertility. A multivariate model was developed, incorporating parameters such as the Matsuda index, vitamin intake, and sexual abstinence duration, to predict motility scores. The study underscores the negative impact of modern civilization’s lifestyle choices on male fertility. Notably, vitamin and mineral consumption, especially from antioxidant-rich diets like the Mediterranean diet, emerged as key modifiable factors affecting fertility. Routine diagnostics for insulin resistance in fertility-related interventions is recommended. The study also highlights the importance of considering sexual abstinence duration during semen collection for accurate diagnostic results. Future research should focus on validating the proposed multivariate model and exploring the effects of lifestyle modifications, particularly vitamin supplementation, on fertility outcomes in men, especially in the context of insulin resistance.

Coastal inundation is recently requiring a significant attention worldwide. The increasing frequency and intensity of extreme events (sea storms, tsunami waves) are highly stressing the coastal envi-ronments, e.g. endangering a large number of residential areas, ecosystems, tourist facilities, and also leading to potential environmental risks. Predicting such events and the generated coastal flooding is thus of paramount importance and can be reached by exploiting the potential of different tools, like remote sensors and numerical modeling. To this aim, a combination is possible between marine radars and wave-resolving propagation models. While instruments like X-band radars are able at precisely reconstructing both wave field and bathymetry within a coastal area that is some kilometers offshore, wave-resolving Boussinesq-type models can reproduce the wave propagation in the nearshore and the consequent coastal flooding. The present work illustrates the reconstruc-tion of coastal data (wave field and seabed depth) conducted using radar signals and a specifically suited data processing, named “Local Method”, and the use of such coastal data to run numerical simulations of wave propagation (using the FUNWAVE-TVD solver) aimed at reproducing coastal inundation over different scenarios. Such scenarios are built using two different European beaches, i.e. Senigallia (Italy) and Oostende (Belgium), and three different directional spreading values, to evaluate the performances in case of either long- or short-crested waves. The overall validation of the methodology, in terms of maximum inundation, shows good performances, especially in case of short-crested wind waves. Furthermore, the application on the Oostende beach demonstrates that the present methodology might work only using open-access tools, i.e. an easy investigation of the coastal inundation and a potential low-cost integration into early warning systems.

As one of the fastest-growing new energy sources, wind power technology has attracted widespread attention from all over the world. In order to improve the quality of wind power generation, wind speed prediction is an indispensable task. In this paper, an error correction based Variational Mode Decomposition and Broad Learning System (VMD-BLS) hybrid model is proposed for wind speed prediction. First, the wind speed is decomposed into multiple components by the VMD algorithm, and then an ARMA model is established for each component to find the optimal number of sequence divisions. Second, the BLS model is used to predict each component, and the prediction results are summed to obtain the wind speed forecast value. However, in some traditional methods, there is always time lag, which will reduce the forecast accuracy. To deal with this, a novel error correction technique is developed by utilizing BLS. Through verification experiment with actual data, it proves that the proposed method can reduce the phenomenon of prediction lag, and can achieve higher prediction accuracy than traditional approaches, which shows our method’s effectiveness in practice.

With the rise of Blockchain technology, the cryptocurrency market has been gaining significant interest. In particular, the number of cryptocurrency traders and the market capitalization have grown tremendously. However, predicting cryptocurrency price is very challenging and difficult due to the high price volatility. In this paper, we propose a classification machine learning approach in order to predict the direction of the market (i.e., if the market is going up or down). We identify key features such as Relative Strength Index (RSI) and Moving Average Convergence Divergence (MACD) to feed the machine learning model. We illustrate our approach through the analysis of Bitcoin close price. We evaluate the proposed approach via different simulations. Particularly, we provide a backtesting strategy. The evaluation results show that the proposed machine learning approach provides buy and sell signals with more than 86% accuracy.

As the outbreak of coronavirus disease 2019 (COVID-19) is continuously increasing in India, so epidemiological modeling of COVID-19 data is urgently required for administrative strategies. Time series and is capable to predict future observations by modeling the data based on past and present data. Here, we have modeled the epidemiological COVID-19 Indian data using various models. Based on the collected COVID-19 outbreak data, we try to find the propagation rule of this outbreak disease and predict the outbreak situations in India. For India data, the time series model gives the best results in the form of predication as compared to other models for all variables of COVID-19. For new cases, new deaths, total cases and total deaths, the best fitted ARIMA models are as follows: ARIMA(0,2,3), ARIMA(0,1,1), ARIMA(0,2,0) and ARIMA(0,2,1). Based on time series analysis, we predict all variables for next month and conclude that the predictive value of Indian COVID-19 data of total cases is more than 20 lakhs with more than 43 thousand total deaths. The present chapter recommended that a comparison between various predictive models provide the accurate and better forecast value of the COVID-19 outbreak for all study variables.

Biomolecular structure drives function, and computational capabilities have progressed such that the prediction and computational design of biomolecular structures is increasingly feasible. Because computational biophysics attracts students from many different backgrounds and with different levels of resources, teaching the subject can be challenging. One strategy to teach diverse learners is with interactive multimedia material that promotes self-paced, active learning. We have created a hands-on education strategy with a set of fifteen modules that teach topics in biomolecular structure and design, from fundamentals of conformational sampling and energy evaluation to applications like protein docking, antibody design, and RNA structure prediction. Our modules are based on PyRosetta, a Python library that encapsulates all computational modules and methods in the Rosetta software package. The workshop-style modules are implemented as Jupyter Notebooks that can be executed in the Google Colaboratory, allowing learners access with just a web browser. The digital format of Jupyter Notebooks allows us to embed images, molecular visualization movies, and interactive coding exercises. This multimodal approach may better reach students from different disciplines and experience levels as well as attract more researchers from smaller labs and cognate backgrounds to leverage PyRosetta in their science and engineering research. All materials are freely available at https://github.com/RosettaCommons/PyRosetta.notebooks.

Geospatial Information Systems (GIS) can provide a great environment for using machine learning algorithm for spatial data such as satellite images. Integrating this functionality with artificial intelligence algorithms for analyzing spatial data enables us to predict challenging disasters such as deforestation. Deforestation as an environmental problems has been recorded the most serious threat to environmental diversity and one of the main components of land-use change. In this paper, we investigate spatial distribution of deforestation using artificial neural networks and satellite imagery. We modeled deforestation process using various factors in determining the relationship between deforestation and environmental and socioeconomic factors. Hence, for this purpose, the proximity to roads and habitats, fragmentation of the forest, height from sea level, slope, and soil type are considered in the model. In this research, we modeled land cover changes (forests) to predict deforestation using an artificial neural network due to its significant potential for the development of nonlinear complex models. The procedure involves image registration and error correction, image classification, preparing deforestation maps, determining layers, and designing a multi-layer neural network to predict deforestation. The satellite images for this study are of a region in Hong Kong which are captured from 2012 to 2016. The results of the study demonstrate that neural networks approach for predicting deforestation can be utilized and its outcomes show the areas that destroyed during the research period.

The study was conducted to evaluate the agronomic performance, forage yield, and nutritive values of Desho grass varieties under supplementary irrigation at Dambi Dollo University experimental site, Western Ethiopia. Three Desho grass varieties (Areka /DZF#590, Kindu kosha-1/DZF #591, and Kulumsa /DZF #592) were arranged in randomized complete block design (RCBD) with three replications. The CROPWAT 8.0 model, local climate data, forage data, and soil data were used to determine Desho grass water requirements and irrigation schedules. The agronomic parameters, yield, chemical composition, and in vitro digestibility of the feed samples at standardization cut were determined following the standard procedures. The results showed significant differences (p

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

Brain-stimulation reward, also known as intracranial self-stimulation (ICSS), is a commonly used procedure for studying brain reward function and drug reward. In electrical ICSS, an electrode is surgically implanted into the medial forebrain bundle in the lateral hypothalamus or the ventral tegmental area in the midbrain. Operant lever responding leads to the delivery of electrical pulse stimulation. The alteration in the stimulation frequency-lever response curve is used to evaluate the impact of pharmacological agents on brain reward function. If a test drug induces a leftward or upward shift in the ICSS response curve, it implies a reward-enhancing or abuse-like effect. Conversely, if a drug causes a rightward or downward shift in the functional response curve, it suggests a reward-attenuating or aversive effect. A significant drawback of electrical ICSS is the lack of cellular selectivity in understanding the neural substrates underlying drug reward versus aversion. Excitingly, recent advancements in optical ICSS (oICSS) have facilitated the development of at least three cell type-specific oICSS models – dopamine-, glutamate-, and GABA-dependent oICSS. In these new models, a comparable frequency-rate response curve has been established and employed to study the substrate-specific mechanisms underlying brain reward function and a drug's rewarding versus aversive effects. In this review article, we summarize recent progress in this exciting research area. The findings in these new behavioral models have not only increased our understanding of the neural mechanisms underlying drug reward and addiction but have also introduced a novel experimental approach in preclinical medication development for treating substance use disorders.

Living organisms are active open systems far from thermodynamic equilibrium. The ability to behave actively corresponds to dynamical metastability: minor but supercritical internal or external effects may trigger major substantial actions such as gross mechanical motion, dissipating internally accumulated energy reserves. Gaining selective advantage from beneficial use of activity requires a consistent combination of sensual perception, memorised experience, statistical or causal prediction models, and resulting favourable decisions on actions. This information processing chain originated from mere physical interaction processes prior to life, here denoted as structural information exchange. From there, the self-organised transition to symbolic information processing marks the beginning of life, evolving by novel purposivity of trial-and-error feedback and accumulation of symbolic information. The emergence of symbols and prediction models can be described as a ritualisation transition, a symmetry-breaking kinetic phase transition of the 2^nd kind previously known from behavioural biology. The related new symmetry is the neutrally stable arbitrariness, conventionality or code invariance of symbols with respect to their meaning. The meaning of such symbols is given by the structural effect they ultimately unleash, directly or indirectly, by deciding on which actions to take. The early genetic code represents the first symbols. The genetically inherited symbolic information is the first prediction model for activities sufficient for survival under the condition of environmental continuity, sometimes understood as a “final causality” property of the model.

This article presents an estimation of the hypertension risk based on a dataset on 1007 individuals. The application of a Tobit Model shows that “Hypertension” is positively associated to “Age”, “BMI-Body Mass Index”, and “Heart Rate”. The data show that the element that has the greatest impact in determining inflation risk is “BMI-Body Mass Index”. An analysis was then carried out using the fuzzy c-Means algorithm optimized with the use of the Silhouette coefficient. The result shows that the optimal number of clusters is 9. A comparison was then made between eight different machine-learning algorithms for predicting the value of the Hypertension Risk. The best performing algorithm is the Gradient Boosted Trees Regression according to the analyzed dataset. The results show that there are 37 individuals who have a predicted hypertension value greater than 0.75, 35 individuals who have a predicted hypertension value between 0.5 and 0.75, while 227 individuals have a hypertension value between 0.0 and 0.5 units.

Predicting the popularity of posts on social networks has taken on significant importance in recent years, and several social media management tools now offer solutions to improve and optimize the quality of published content and to enhance the attractiveness of companies and organizations. Scientific research has recently moved in this direction, with the aim of exploiting advanced techniques such as machine learning, deep learning, natural language processing, etc., to support such tools. In light of the above, in this work we aim to address the challenge of predicting the popularity of a future post on Instagram, by defining the problem as a classification task and by proposing an original approach based on Gradient Boosting and feature engineering, which led us to promising experimental results. The proposed approach exploits big data technologies for scalability and efficiency and is general enough to be applied to other social media as well.

Studies show that although female soccer players often have shorter change of direction (COD) deficits than males, indicating different biomechanical profiles, there is lack of research on the impact of physical metrics on COD performance in females. The aim of this study was to analyze whether performance metrics based on speed, and jumping could explain the variation in %CODD in young female soccer players. Thirty-three highly trained adolescent female soccer players (age: 16. ± 0.95 years; height: 160.4 ± 5.22 cm; body mass: 55.7 ± 7.22 kg) performed COD180 tests, 10-m and 30-m sprint test and single leg countermovement and horizontal jumps. Acceleration in the first 10 meters of a sprint was identified as a significant predictor of COD180 performance (R2 = 28%), (R2 = 50%), (p

Rising incidences of cutaneous melanoma have fueled the development of statistical models that predict the individual melanoma risk. Our aim was to assess the validity of published prediction models for incident cutaneous melanoma using a standardized procedure based on PROBAST (Prediction model Risk Of Bias ASsessment Tool). We included studies that were identified by a recent systematic review and updated the literature search to ensure that our PROBAST rating included all relevant studies. Six reviewers assessed the risk of bias (ROB) for each study using the published “PROBAST Assessment Form” that consists of four domains and an overall rating of ROB. We further examined a temporal effect regarding changes in overall and domain-specific ROB rating distributions. Altogether 42 studies were assessed, of which a vast majority (n=34; 81%) was rated as having high ROB. Only one study was judged as having low ROB. The main reasons for high ROB ratings were the use of hospital controls in case-control studies and the omission of any validation of prediction models. However, our results of the temporal analysis showed a significant reduction in the number of studies with high ROB for the domain analysis. Nevertheless, the evidence base of high-quality studies that can be used to draw conclusions on the prediction of incident cutaneous melanoma is currently much weaker than the high number of studies on this topic would suggest.

Continuum robots play the role of end-effector in various surgical robots and endoscopic devices. The robots may be categorized as rigid or soft continuum robots (SCRs). While the SCRs have proven advantages such as safety and compliance, more research and development are required to enhance their capability for specific medical scenarios. This research aims at designing a soft robot considering concepts of geometric and kinematic similarities. The chosen application is a semi-invasive medical application known as Transesophageal Echocardiography (TEE), but the methodology can be implemented in other similar applications. Since established rigid carrier construction make use of principles we find as well embodied in vertebral spines, the paragon for soft robot solution can be the phylogenetic precursor of the spine, the Chorda dorsalis. The feasibility of fabrication of a soft endoscopic device derived from that paragon within a robotics laboratory was shown empirically by producing a three-segment pneumatic SCR. The kinematic model was proposed based on the method of transformation matrices, and an algorithm based on a self-organizing map (SOM) was proposed and applied to realize kinematic similarity. The simulation results indicate that the algorithm acting as an open-loop controller forces the soft robot tip to follow the desired path which in this case is the path of the rigid probe. It is concluded that the solution provides a soft robot that can surrogate and succeed the traditional rigid counterpart owing to size, workspace, and kinematics.

Predicting anomalies in manufacturing assembly lines is crucial for reducing time and labor costs and improving processes. For instance, in rocket assembly, premature part failures can lead to significant financial losses and labor inefficiencies. With the abundance of sensor data in the Industry 4.0 era, machine learning (ML) offers potential for early anomaly detection. However, current ML methods for anomaly prediction have limitations, with F1-measure scores of only 50% and 66% for prediction and detection, respectively. This is due to challenges like the rarity of anomalous events, scarcity of high-fidelity simulation data (actual data is expensive), and the complex relationships between anomalies not easily captured by traditional ML approaches. Specifically, these challenges relate to two dimensions of anomaly prediction: predicting when anomalies will occur and understanding the dependencies between them. This paper introduces a new method called Robust and Interpretable 2D Anomaly Prediction (RI2AP) designed to address both dimensions effectively. RI2AP is demonstrated on a rocket assembly simulation, showing up to a 30-point improvement in F1 measure compared to current ML methods. This highlights its potential to enhance automated anomaly prediction in manufacturing. Additionally, RI2AP includes a novel interpretation mechanism inspired by a causal-influence framework, providing domain experts with valuable insights into sensor readings and their impact on predictions. Finally, the RI2AP model is deployed in a real manufacturing setting for assembling rocket parts. Results and insights from this deployment demonstrate the promise of RI2AP for anomaly prediction in manufacturing assembly pipelines.

This paper investigates the roll parameter estimation of periodic disturbances where the amplitude, frequency, offset, and phase are hardly recognized in real practice. The key problem is to make an estimation that could eliminate the unknown disturbance parameters. An adaptive mechanism applies these four parameters to the globally exponential convergence using linear second-order filters and parameter estimation errors. Then, a backstepping controller is employed to make an exponential convergence to zero of the state variables. Moreover, reservoir computing is used to forecast chaotic roll motions to support predictability using Lyapunov exponents and the Poincaré map. Numerical simulations are demonstrated to validate the dynamical behaviors and efficacy of the proposed control scheme with machine learning.

Infrared dim and small target detection is a key technology of various detection tasks. However, due to the lack of shape, texture, and other information, it is a challenging task to detect dim and small targets. Recently, since many traditional algorithms ingore global information of infrared images, they generate some false alarms in complicated environments. To address this problem, in this paper, a coarse-to-fine deep learning-based method is proposed to detect dim and small targets. Firstly, a coarse-to-fine detection framework integrating deep learning and background prediction is applied for detecting targets. The framework contains of coarse detection module and fine detection module. In coarse detection stage, Region Proposal Network (RPN) is employed to generate masks in target candidate regions. Then, for further optimize the result, inpainting is utilized to predict the background by the global semnantic of images. In this paper, inpainting algorithm with a mask aware dynamic filtering module is incorporated into the fine detection stage to estimate background in candidate target areas. Finally, compared with existing algorithms, the experimental results indicate that the proposed framework have effective detection capability and robustness for complex surroundings.

According to the World Health Organization (WHO), dementia is the seventh leading reason of death among all illnesses and one of the leading causes of disability among the world’s elderly people. Day by day the number of Alzheimer’s patients is raising. Considering the increasing rate and the dangers, Alzheimer’s disease should be diagnosed carefully. Machine learning is a potential technique for Alzheimer’s diagnosis but general users do not trust machine learning models due to the black-box nature. Even, some of those models do not provide the best performance because of using only neuroimaging data. To solve these issues, this paper proposes a novel explainable Alzheimer’s disease prediction model using a multimodal dataset. This approach performs a data-level fusion using clinical data, Freesurfer MRI segmentation data, and psychological data. For Alzheimer’s disease vs cognitively normal prediction, the random forest classifier provides 100% accuracy. Furthermore, Alzheimer’s disease and non-Alzheimer’s dementia should be classified properly because their symptoms are similar. To the best of our knowledge, we are the first to present a three-class classification on Alzheimer’s disease vs cognitively normal vs non-Alzheimer’s dementia and achieved 99.86% accuracy using an ensemble model. Besides, a novel Alzheimer’s patient management architecture is also proposed in this work..

This paper presents a two-way factor design incorporating both spatial and temporal variation in the prediction of COVID 19 in Africa. In line with this, the impact of COVID-19on the GDP in Africa is well scrutinized. In contrast to the existing works [1–3], this work also extends the two-factor design into the one-way factor design through incorporating covariates into spatial effects. The data rely on the spatial and temporal obtained from WHO datasets [4, 5]. The one-factor design with more covariates is taken into consideration to identify the major potential predictor variables responsible for the deaths and confirmed cases due to COVID 19 in Africa. The MANCOVA considered population density, temperature, humidity; perception, and wind are all considered as co-variates. Simulations show that the two-way analysis of variance has shown that there is a statistically significant difference between the spatial (Fcal= 8.2704, Pvalue= 3.099∗10−6)and temporal (Fcal= 48.7964, Pvalue= 9.147∗10−16) effects. South Africa and Nigeria are highly influencing due to the pandemic where their GDP also relatively mostly declined. A significant economic change is observed before the pandemic and after the outbreak of the pandemic(tcal= 2.9548, Pvalue= 0.01805). COVID 19 negatively influenced the economy of1 most of the African countries. The population density, temperature, and wind are found to be statistically significantly associated with COVID 19 cases and deaths.

An application of deep convolutional neural network and recurrence plot for financial market movement prediction is presented. Though it is challenging and subjective to interpret its information, the pattern formed by a recurrence plot provide a useful insight into the dy- namical system. We used a recurrence plot of seven financial time series to train a deep neural network for financial market movement predic- tion. Our approach is tested on our dataset and achieved an average of 53.25% classification accuracy. The result suggests that a well trained deep convolutional neural network can learn a recurrence plot and pre- dict a financial market direction.

We write the mutual information between an input speech utterance and its reconstruction by a Code-Excited Linear Prediction (CELP) codec in terms of the mutual information between the input speech and the contributions due to the short term predictor, the adaptive codebook, and the fixed codebook. We then show that a recently introduced quantity, the log ratio of entropy powers, can be used to estimate these mutual informations in terms of bits/sample. A key result is that for many common distributions and for Gaussian autoregressive processes, the entropy powers in the ratio can be replaced by the corresponding minimum mean squared errors. We provide examples of estimating CELP codec performance using the new results and compare to the performance of the AMR codec and other CELP codecs. Similar to rate distortion theory, this method only needs the input source model and the appropriate distortion measure.

The accuracy of sales prediction models based on the big data of online word-of-mouth (eWOM) is still not satisfied. We argue that eWOM contains heat and sentiments of different product dimensions, which can improve the accuracy of these models. In this paper, we propose a dynamic topic analysis (DTA) framework in order to extract heat and sentiments of product dimensions from the big data of eWOM. Finally, we propose an autoregressive-heat-sentiment (ARHS) model, which integrates heat and sentiments of dimensions into the baseline predictive model. The empirical study in movie industry confirms that heat and sentiments of dimensions can improve the accuracy of sales prediction model. ARHS model is better for movie box-office revenue prediction than other models.

Propolis is a bee product widely used as a dietary supplement and included in sweets or baby foods due to its well-known antioxidant and nutritional properties that are directly correlated with its phenolic composition. For this reason, this study analysed the total contents of flavones and flavonols, flavanones and dihydroflavonols, and the antioxidant capacity by using the methods of ABTS and linoleic acid/β-carotene in 99 samples of propolis from Spain and Chile. A rapid method was developed for quantifying these parameters in raw propolis using near infrared (NIR) spectroscopy with an optical fibre probe of remote reflectance applied directly to the ground up sample. The models developed allow the determination of the total of flavones and flavonols (0-183 mg rutin/ g propolis), of the total of flavanones and dihydroflavonols (9-109 mg pinocembrin/ g propolis extract), and the antioxidant capacity by the ABTS method (0-3212 nmolesTrolox/ mg of propolis) and of linoleic acid/β-carotene (22-86% inhibition). The NIR spectroscopy models were applied in external validation to different samples of the calibration group, which led to the conclusion that the methods developed provide significantly identical data to the initial chemical data of reference.