Comparisons of power flows and efficiencies in two structurally quite similar cylindrical series-parallel planetary gear systems (PGSs) were performed in three separate parts of this paper. Each of these single degree of freedom (DoF) systems consists of three different 2KH subsystems connected in series-parallel. The main goal was to prove that apart from complex, structurally and dynamically coupled PGSs, there are also complex and only structurally coupled PGSs, in which the phenomenon of power flow circulation inside closed loops does not occur. Such a half-coupled type of PGS is herein called pseudo-coupled. Therefore, Part I discusses in detail the geometry, kinematics and statics of coupled PGSs in order to determine power flow paths. A comparison of the directions of power flow in both types of PGSs can be made in Part II after determining the power flow paths in the second planetary gear in a similar way. The directions of power flow in both types of PGSs were determined in a relatively simple way, thanks to the distinction between active and passive torques and thus active and passive shafts of individual subsystems. The efficiency comparison made in Part III will show whether power circulation has an influence on the efficiency value, at least in these two types of PGSs.

The energy transition towards renewable and more decentral power production triggers the need for grid and storage expansion on all voltage levels. Today's power system planning focuses on certain voltage levels or spatial resolutions. In this work we present an open source software tool eGo which is able to optimize grid and storage expansion throughout all voltage levels in a developed top-down approach. System costs are minimized by applying a linear optimal power flow considering the grid infrastructure of the extra-high and high-voltage (380 to 110 kV) level. Hence, the common differentiation of transmission and distribution grid is partly dissolved, integrating the high-voltage level into the optimization problem. Consecutively, optimized curtailment and storage units are allocated in the medium voltage grid in order to lower medium and low voltage grid expansion needs, that are consequently determined. Here, heuristic optimization methods using the non-linear power flow were developed. Applying the tool on future scenarios we derived cost-efficient grid and storage expansion for all voltage levels in Germany. Due to the integrated approach storage expansion and curtailment can significantly lower grid expansion costs in medium and low voltage grids and at the same time serve the optimal functioning of the overall system. Nevertheless, the cost-reducing effect for the whole of Germany was marginal. Instead, the consideration of realistic, spatially differentiated time series lead to substantial overall savings.

We present the results of direct numerical simulations of power spectral densities for kinetic energy, convective entropy and heat flux for unsteady Rayleigh-Bénard magnetoconvection in the frequency space. For larger values of frequency, the power spectral densities for all the global quantities vary with frequency f as f⁻². The scaling exponent is independent of Rayleigh number, Chandrasekhar’s number and thermal Prandtl number.

To quantitatively estimate the risk of power system operation under extreme rainfall, a multi-scenario stochastic risk assessment method is proposed. First, a scenario generation scheme considering waterlogged faults of power facilities is constructed based on the storm water management model (SWMM) and the extreme learning machine method. These scenarios will be merged to several typical scenario sets for further processing. The outage of power facilities will induce power flow transfer which may consequently lead to transmission lines’ thermal limit violation. Semi-invariant and Gram-Charlier level expansion methods are adopted to analytically depict the probability density function and cumulative probability function of each line’s power flow. The optimal solution is performed by a particle swarm algorithm to obtain proper load curtailment at each bus, and consequently the violation probability of line thermal violations can be controlled within an allowable range. The volume of load curtailment as well as their importance are considered to quantitatively access the risk of power supply security under extreme precipitation scenarios. The effectiveness of the proposed method is verified in case studies based on the IEEE 24-bus system.

The local reactive power control in distribution grids with a high penetration of distributed energy resources (DERs) is essential in future power system operation. Appropriate control characteristic curves for DERs support stable and efficient distribution grid operation. However, the current practice is to configure local controllers collectively with constant characteristic curves that may not be efficient for volatile grid conditions or the desired targets of grid operators. To address this issue, this paper proposes a time series optimization-based method to calculate control parameters, which enables each DER to be independently controlled by an exclusive characteristic curve for optimizing its reactive power provision. To realize time series optimizations, the open-source tools pandapower and PowerModels are interconnected functionally. Based on the optimization results, Q(V)- and Q(P)-characteristic curves can be individually calculated using the linear decision tree regression to support voltage stability and provide reactive power flexibility and potentially reduce grid losses and component loadings. In this paper, the newly calculated characteristic curves are applied in two representative case studies, and the results demonstrate that the proposed method outperforms the reference ones suggested by grid codes.

This paper proposes a method based on genetic algorithm (GA) for the security-constrained optimal dispatch of integrated natural gas and electricity networks, considering operating scenarios in both energy systems. The mathematical formulation of the optimization problem consists of a multi-objective function which aims to minimize both cost of thermal generation (diesel and natural gas) as well as the production and transportation of natural gas. The joint gas-electricity system is modeled by two separate groups of nonlinear equation, which are solved by the combination of Newton's method with the GA. The applicability of the proposed method is tested in the Belgian gas network integrated with the IEEE 14-bus test system and a 15-node natural gas network integrated with the IEEE 118-bus test system. The results demonstrate that the proposed method provides efficient and secure solutions for different operating scenarios in both energy systems.

The integration of diverse distributed generation (DG) units, encompassing both Renewable Energy Sources (RES) and non-RES technologies delves into voltage levels, current distributions, and power flows, aiming to optimize and effectively manage the distribution network. An RES-based DGs such as photovoltaic systems and wind turbines, alongside non-RES units like fuel cells and micro turbines. This study proposes a hybrid approach the Multi-Objective Genetic Algorithm - Grey Wolf Optimizer (MOGA-GWO). By merging the strengths of multi-objective genetic algorithms with the efficiency of the Grey Wolf Optimizer, this advanced algorithm seeks semi-optimal solutions for multi-objective optimization problems. The algorithm aims to improve convergence speed without compromising solution quality, offering a promising solution for optimizing the characteristics of DG and RES integration in distribution networks compared to Cuckoo Search and Simulation Annealing Techniques. Key algorithmic operations include individual representation, initialization, fitness function computation, selection, crossover, mutation, and ending conditions. The DG optimal power flow problem is explored with a focus on minimizing generation costs, improving voltage profiles, minimizing losses, enhancing reliability, integrating renewable energy, reducing environmental impact, managing congestion, and ensuring compliance with operational constraints. Beyond traditional considerations, the study emphasizes neglected objectives and constraints, such as cyber-security concerns, real-time operation, regulatory frameworks, social acceptance, lifecycle environmental impact, grid resilience, data privacy, aging infrastructure compatibility, and economic viability.

The calculation of power flow in power systems with the presence of harmonics has been properly studied in the scientific literature. However, power flow calculation considering interharmonic components is still an open question. Traditional methods based on the IEEE1459 standard have proven to be valid and accurate only for linear and sinusoidal systems, but have been criticized for non-linear and non-sinusoidal systems because they are not able to explain correctly the current and voltage interactions beyond the active power. This paper proposes the use of a novel mathematical framework called geometric algebra (GA) to study the power flow considering the interaction of current and voltage harmonics and interharmonics. The use of GA enables the precise determination of the direction and magnitude of the total and single active power flow for each component, as well as other power elements related to the non-active power due to cross interaction. Moreover, this paper makes a novel contribution to the definition of interharmonics in geometric algebra space that has not been done before. To test the validity of the method, both linear and non-linear circuits are proposed and solved by applying voltages and currents with harmonic and interharmonic components. The results obtained show that power flow can be analyzed under the prism of the principle of energy conservation (PoCoE) in a way that allows a better understanding of the power spectrum due to the interaction of harmonics and interharmonics of voltage and current.

Keeping the bus voltage within acceptable limits depends on dispatching reactive power. Power quality improves as a result of creating an effective power flow system, which also helps to reduce power loss. Therefore, Optimal Reactive Power Dispatch (ORPD) studies aim at designing appropriate system configurations to enable a reliable operation of power systems. Establishment of such a configuration is handled through control variables in power systems. On the other hand, installing Distributed Generation Unit (DGU) into a power system can have an important effect on power quality and power loss minimization. In this paper, Grey Wolf Optimization (GWO method is applied to ORPD problem for the first time, to find optimal placement of newly installed DGUs at the power system. Active power loss and voltage minimization have been minimized by optimizing the control variables while keeping them within their upper and lower bounds, and by finding the optimal placement of a newly installed DGU in power system. On the basis of IEEE 30 bus and IEEE 118 bus systems, performance of the suggested approach is investigated. A comparison is also performed among the proposed method and some other methods. Test results demonstrate that the resulting configuration contributes to growing the rate of renewable integration to a power system. The results also indicate that the suggested optimization approach applied to ORPD problem has improved power system performance in terms of both on power loss and voltage deviation. The promising results highlight the potential of the GWO algorithm to facilitate the integration of renewable power sources, and its role in promoting sustainable energy solutions.

The growing integration of renewable energy sources (RES) into the power system causes congestion to occur more frequently. In order to reduce congestion in the short term and to make the utilization of the power system more efficient in the long term, power flow control (PFC) in the transmission system has been proposed. However, exemplary studies show that congestion will increase also in the distribution system if the transmission system is expanded. For this reason, the potential of PFC to reduce congestion in a model of a real 110 kV distribution system is investigated. Several Unified Power Flow Controller (UPFC) devices are optimized in terms of their number and placement in the power system, their size, control parameters, and costs, by using a Parallel Tempering approach as well as a greedy algorithm. Two optimization variants are considered, one reducing the number of degrees of freedom by integrating system knowledge while the other is not. We find that near a critical grid state and disregarding costs, PFC can reduce congestion significantly (99.13 %). When costs of the UPFCs are taken into account, PFC can reduce congestion by 73.2 %. A basic economic analysis of the costs reveals that the usage of UPFCs is profitable. Furthermore, it is found that the reduction of the solution space of the optimization problem leads to better results faster and that, contrary to expectations, the optimization problem is simple to solve. The developed methods allow not only for the determination of the optimal use of UPFCs to minimize congestion, but also to estimate their profitability.

This paper proposes the impact of plug-in electric vehicles integrated into power distribution system based on voltage dependent control. The plug-in electric vehicles was modeled as the static load model in power distribution systems under balanced load condition. The power flow analysis is determined by using the basic parameters of the electrical network. The main point of this study are compare with voltage magnitude profiles, load voltage deviation, and total power losses of the electrical power system. There are investigating the affected from constant power load, constant current load, constant impedance load and plug-in electric vehicles load, respectively. The IEEE 33 bus test system is used to test the proposed method by assigning each load type to a balanced load in steady state and applied the solving methodology based on the bus injection to branch injection matric, branch current to bus voltage matrix, and current injection matrix to solve the power flow problem. The simulation results showed that the plug-in electric vehicles load had the lowest impact compared to other loads. The lowest plug-in values for the electric vehicle loads were 0.062, 119.67 kW and 79.31 kVar for the load voltage deviation, total active power loss and total reactive power loss, respectively. Therefore, this study can be verified that the plug-in electric vehicles load were affected to the lowest of the electrical power system in condition to same sizing and position. So that, in condition to the plug-in electric vehicles load added into the electrical power system with the conventional load type or complex load type could be considered that the affected from the plug-in electric vehicles load in next study.

Small hydro-power systems seem to be the best solution for energy generation through the use of pump as turbine (PAT) due to its low cost and lesser environmental hazards associated with it. Recently, PAT applications are gaining global attention in energy generation but its operation is not fully understood. The performance and flow behavior is affected by several operational conditions. This study seeks to investigate the effects of rotational speed on flow behavior and performance of a PAT. Rotational speed is an important physical parameter that affects the operation of a PAT. A selected centrifugal pump model of four blades and splitters was used for the study. Numerical simulations were carried out using k-ε turbulence model to solve the three-dimensional (3D) equations in both pump and PAT modes. The outcomes were then validated using experimental results in the pump mode to obtain overview flow physiognomies. The results predicted that the efficiency increases as the rotational speed increases in the pump mode whereas in turbine mode, higher rotational speed cannot convert hydraulic energy into mechanical energy. Thus, a rotational speed of 1500 rpm performed the highest efficiency of 69.8% at QBEP among the other rotational speeds selected. Moreover, the head performance in the turbine mode increases as the flow rate increases. This research provides useful information which will help improve PAT performance as well as selecting PAT for small hydro-power site.

The incorporation of renewable energy into power systems poses serious challenges to the transmission and distribution power system operators (TSOs and DSOs). To fully leverage these resources there is a need for a new market design with improved coordination between TSOs and DSOs. In this paper we propose two coordination schemes between TSOs and DSOs: one centralised and another decentralised that facilitate the integration of distributed based generation; minimise operational cost; relieve congestion; and promote a sustainable system. To this end, we approximate the power equations with linearised equations so that the resulting optimal power flows (OPFs) in both the TSO and DSO become convex optimisation problems. In the resulting decentralised scheme, the TSO and DSO collaborate to optimally allocate all resources in the system. In particular, we propose an iterative bi-level optimisation technique where the upper level is the TSO that solves its own OPF and determines the locational marginal prices at substations. We demonstrate numerically that the algorithm converges to a near optimal solution. We study the interaction of TSOs and DSOs and the existence of any conflicting objectives with the centralised scheme. More specifically, we approximate the Pareto front of the multi-objective optimal power flow problem where the entire system, i.e., transmission and distribution systems, is modelled. The proposed ideas are illustrated through a five bus transmission system connected with distribution systems, represented by the IEEE 33 and 69 bus feeders.

In power systems, flow allocation (FA) methods allow to allocate usage and costs of the transmission grid to each single market participant. Based on predefined assumptions, the power flow is split into isolated generator specific or producer specific sub-flows. Two prominent FA methods, Marginal Participation (MP) and Equivalent Bilateral Exchanges (EBE), build upon the linearized power flow and thus on the Power Transfer Distribution Factors (PTDF). Despite their intuitive and computationally efficient concept, they are restricted to networks with \emph{passive} transmission elements only. As soon as a significant number of \emph{controllable} transmission elements, such as High-voltage direct current (HVDC) lines, operate in the system, they loose their applicability. This work reformulates the two methods in terms of Virtual Injection Patters (VIP) which allows to efficiently introduce a shift parameter $q$, tuning contributions of net sources and net sinks in the network. Major properties and differences of the methods are pointed out. Finally, it is shown how the MA and EBE algorithm can be applied to generic meshed AC-DC electricity grids: Introducing a \emph{pseudo-impedance} which reflects the operational state of controllable elements, allows to extend the PTDF matrix under the assumption of knowing the current system's flow. Basic properties from graph theory are used for solving the pseudo-impedance dependent on the position in the network. This directly enables \emph{e.g.} HVDC lines to be considered in the MP and EBE algorithm. The extended methods are applied to a low-carbon European network model (PyPSA-EUR) with a spatial resolution of N=181 and an 18\% transmission expansion. The allocations of VIP and MP, show that countries with high wind potentials profit most from the transmission grid expansion. Based on the average usage of transmission system expansion a method of distributing operational and capital expenditures is proposed. Further it is shown, how injections from renewable resources strongly drive country-to-country allocations and thus cross-border electricity flows.

In electric circuits, energy is delivered by electromagnetic fields through the space, as suggested by Kraus and Carver. They provide insights by showing electric/magnetic fields and Poynting vector directions around a DC circuit. In this work, the energy flow mechanism by Kraus and Carver is further studied theoretically for arbitrary terminal potentials of a DC power source.

In this paper, a multi-operator differential evolution algorithm (MODE) is proposed to solve the Optimal Power Flow (OPF) problem and is called MODE-OPF. The MODE-OPF utilizes the strengths of more than one differential evolution (DE) operator in a single algorithmic framework. Additionally, an adaptive method (AM) is proposed to update the number of solutions evolved by each DE operator based on both the diversity of population and quality of solutions. This adaptive method has the ability to maintain diversity at the early stages of the optimization process and boost convergence at the later ones. The performance of the proposed MODE-OPF is tested by solving OPF problems for both small and large IEEE bus systems (i.e., IEEE-30 and IEEE-118) while considering the intermittent solar and wind power generation. To prove the suitability of this proposed algorithm, its performance has been compared against several state-of-the-art optimization algorithms, where MODE-OPF outperforms other algorithms in all experimental results and thereby improving a network's performance with lower cost. MODE-OPF decreases the total generation cost up to 24.08%, the real power loss up to 6.80% and the total generation cost with emission up to 8.56%.

This paper proposes a Mixed Integer Conic Programming (MICP) model for community microgrids considering the network operational constraints and building thermal dynamics. The proposed multi-objective optimization model optimizes not only the operating cost, including fuel cost, purchasing cost, battery degradation cost, voluntary load shedding cost and the cost associated with customer discomfort due to room temperature deviation from the set point, but also several performance indices, including voltage deviation, network power loss and power factor at the Point of Common Coupling (PCC). In particular, the detailed thermal dynamic model of buildings is integrated into the distribution optimal power flow (D-OPF) model for the optimal operation. The heating, ventilation and air-conditioning (HVAC) systems can be scheduled intelligently to reduce the electricity cost while maintaining the indoor temperature in the comfort range set by customers. Numerical simulation results show the effectiveness of the proposed model and significant savings in electricity cost with network operational constraints satisfied.

As a consequence of the increasing share of renewable energies and sector coupling technologies, new approaches are needed for the study, planning, and control of modern energy systems. Such new structures may add extra stress to the electric grid, as is the case with heat pumps and electrical vehicles. Therefore, the optimal performance of the system must be estimated considering the constraints imposed by the different sectors. In this research, a dispatch optimization method with an iterative grid constraint generation, decoupled from the linear unit commitment problem, is employed. From the considered scenarios, it was found that in a typical German neighborhood with 150 households, PV penetration of ∼5kWp per household can lead to curtailment of ∼60MWh per year due to line loading. Furthermore, the proposed method eliminates grid violations due to the addition of new sectors reducing the curtailment up to 60%. With the optimization of the heat pump operation, an increase of 7% of the self-consumption was achieved with similar results for the combination of battery systems and electrical vehicles. In conclusion, a safer and optimal operation of a complex energy system is fulfilled. Safer control strategies and more accurate plant sizing could be derived from this work.

This work aims to develop an integrated fault location and restoration approach for microgrids (MGs). This work contains two parts. Part I presents the fault location algorithm, and Part II shows the restoration algorithm. The proposed algorithms are implemented by particle swarm optimization (PSO). The fault location algorithm is based on network connection matrices, which are the modifications of bus-injection to branch-current and branch-current to bus-voltage (BCBV) matrices, to form the new system topology. The backward/forward sweep approach is used for the prefault power flow analysis. After the occurrence of fault, the voltage variation at each bus is calculated by using the Zbus modification algorithm to modify Zbus. Subsequently, the voltage error matrix is computed to search for the fault section by using PSO. After the allocation of the fault section, the multi-objective function is implemented by PSO for optimal restoration with its constraints. Finally, the IEEE 37-bus test system connected to distributed generations is utilized as the sample system for a series simulation and analysis. The outcomes demonstrated that the proposed optimal algorithm can effectively solve the fault location and restoration problem in MGs.

HybridAC/DC microgrids(HMG) are emerging as an attracting method for integrating the AC/DC distributed energy resources(DERs) with the features of high-performance and low-cost. In the isolated hybrid AC/DC microgrid (IHMG), the key problem is how to balance the power variation and regulate the voltage and frequency. Various energy storage systems (ESS)and interlinking converter (IC) technologies are viable for this application. The present study proposes a novel unified power flow model to evaluate and compare the abilities of the ESS with different connection topologies and ICs with different control approaches to maintain the voltage and frequency stability of the IHMG. In order to investigate the performance of the proposed scheme, five operation modes of the IHMG are defined and explained. The classification is based on the connection topologies and control modes of the ESS/IC in the IHMG. Then, a set of generic PF equations are derived. Moreover, three binary matrices are applied in the construction of the unified power equations. These matrices are used for describing the running state of the IHMG. Finally, in order to verify the proposed scheme, it is applied to several case studies of the IHMG. The operation characteristics of multi-DC subgrids IHMG in different modes, particularly when an external disturbance occurs, are investigated.

the intermittency and variability of these permeated Distributed Generators (DGs) could critically cause many security and economy risks to distribution systems. This paper applied a certain mathematical distribution to imitate the output variability and uncertainty of DGs. And then, four risk indices EENS, PLC, EFLC and SI were established to reflect the system risk level of distribution system. For the certain mathematical distribution of the DGs' output power, a developed PEM (point estimate method)-based method was proposed to calculate these four system risk indices. In this developed PEM-based method, enumeration method was used to list the states of distribution systems, an improved PEM was presented to deal with the uncertainties of DGs and the value of load curtailment in distribution systems was calculated by an optimal power flow algorithm. Finally, the effectiveness and advantages of this proposed PEM-based method for distribution system assessment were verified by the tests of a modified IEEE 30-bus system. Simulation results have shown that this proposed PEM-based method has a high computational accuracy and highly reduced computational costs compared with other risk assessment methods and is very effective for risk assessments.

Using graph theory, computer aided motion, static force and power flow analysis of planetary gear mechanism is realized. The motion, static force and efficiency calculations of 6HP26 automatic transmission are carried out. Based on kinematic and static force analysis model, related matrices are acquired. Hence, kinematic and static force analysis of planetary gear mechanism is achieved. The link power can be determined by the link speed and torque. Power flow diagrams of each gear are acquired. The efficiency is calculated by transmission ratio method.

Integrating large-scale wind energy in modern power systems is demanding more efficient mathematical models to properly address classical assumptions in power system problems. In particular, there are two main assumptions in power system problems with wind integration that have not been adequately studied yet; First, non-linear AC power flow equations have been linearized in most of the literature. Such simplifications can lead to inaccurate power flow calculations that may result in other technical issues. Second, wind power uncertainties are inevitable and have been mostly modelled using the traditional uncertainty modelling approaches, that may not be suitable for large-scale wind power integration. In this paper, we address both challenges: we present a tight second-order conic relaxation (SOCR) for optimal power flow (OPF) problem, and simultaneously, implement the new effective budget of uncertainty approach for uncertainty modelling that determines the maximum wind power admissibility first and then addresses the uncertainty in the model. To the best of our knowledge, this is the first study that proposes an effective robust second-order conic programming (ERSOCP) model that simultaneously addresses the issues of power flow linearization and wind power uncertainty with the new paradigm on the budget of uncertainty approach. Our numerical results show the merit of the proposed model against traditional linearized power flow equations as well as traditional uncertainty modelling approaches.

The power-generation capacity of grid-connected photovoltaic (PV) power systems is increasing. As output power forecasting is required by electricity market participants and utility operators for the stable operation of power systems, several methods have been proposed using physical and statistical approaches for various time ranges. A short-term (30 min ahead) forecasting method has been previously proposed by our laboratory for geographically distributed PV systems using motion estimation. This study focuses on an important parameter for estimating the proposed motion and optimizing the parameter. This parameter is important because it is associated with the smoothness of the vector field, which is the result of motion estimation and influences the forecasting accuracy. In the periods with drastic power output changes, the evaluation was conducted on 101 PV systems located within a circle of 15-km radius in the Kanto region of Japan. The results indicate that the absolute mean error of the proposed method with the optimized parameter is 10.3%, whereas that of the persistent prediction method is 23.7%. Therefore, the proposed method is effective in forecasting for periods when PV output changes drastically in a short time.

We analyzed the peak spring tidal current speeds, annual mean tidal power densities (TPD) and annual energy production (AEP) obtained from experiment 06.1, referred as the "HYCOM model" throughout, of the three dimensional (3D), global model HYCOM in an area covering the Baja California Pacific and the Gulf of California. The HYCOM model is forced with astronomical tides and surface winds alone, and therefore is particularly suitable to assess the tidal current and wind-driven current contribution to in-stream energy resources. We find two areas within the Gulf of California, one in the Great Island Region and one in the Upper Gulf of California, where peak spring tidal flows reach speeds of 1.1 meters per second. Second to fifth-generation tidal stream devices would be suitable for deployment in these two areas, which are very similar in terms of tidal in-stream energy resources. However, they are also very different in terms of sediment type and range in water depth, posing different challenges for in-stream technologies. The highest mean TPD value when excluding TPDs equal or less than 50 W/m² (corresponding to the minimum velocity threshold for energy production) is of 172.8 W/m², and is found near the town of San Felipe, at (lat lon) = (31.006 -114.64); here energy would be produced during 39.00% of the time. Finally, wind-driven currents contribute very little to the mean TPD and the total AEP. Therefore, the device, the grid, and any energy storage plans need to take into account the periodic tidal current fluctuations, for optimal exploitation of the resources.

Sediment transport is highly sensitive to flow conditions, showing significant increase during flood events. Based on this principle, this study set out to rank flood events occurring along river Trotuș (Romania) based on the amount of transported sediment and event duration. The 77 flood events recorded from 2000 to 2017 were ranked into 4 classes: type A (4%); type B (16%), type C (14%) and type D (66%). The sediment transport specific for the 4 types of flood events was related to the flow discharge (sediment rating curve and hysteresis effect), the specific stream power and the energy expenditure of these events. More than 60% of the hysteresis loops typical for flood events were clockwise, thus singling out the channel as the main sediment source. Ca. 74% of the total sediment yield was transported at stream power values higher than the 300 Wm-2 threshold, which was exceeded in less than 1% of the investigated timeframe. The changes occurring in the sediment transport rates after major floods show that these events are significant thresholds in the hydrogeomorphic evolution of river channels.

Pressure drop and flow pattern of oil-water flows were investigated in a 19 mm ID clear polyvinyl chloride pipe consisting of U-bend with radius of curvature of 100 mm. The range for oil and water superficial velocities tested were and respectively. Measurements were carried out under different flow conditions in a test section that consisted of four different parts: upstream of the bend, at the bend and at two redeveloping flow locations after the bend. The result indicated that the bend had limited influence on downstream flow patterns. However, the shear forces imposed by the bend caused some shift flow pattern transition and bubble characteristics in the redeveloping flow section after the bend relative to develop flow before the bend. Generally, pressure gradient at all the test sections increased with both oil fraction and water superficial velocity and there was a sharp change of pressure gradient profile during phase inversion. The transition point where phase inversion occurred was always within the range of . Pressure losses differed at the various test sections and the difference was strongly linked to the superficial velocity of the phases and the flow pattern. At high mixture velocity, pressure losses at the redeveloping section after the bend were higher than that at the bend and that for fully developed flows. At low mixture velocity, pressure losses at the bend are higher than in the straight sections. Pressure drop generally decreased with level of flow development downstream of the bend.

The flow properties of pellets or granules are crucial for further processing the drug dosage forms. Optimal compression or filling the multiparticulate dosage forms into capsules is influenced by forces between discrete particles, which could be partially characterized by flow properties. Several techniques were developed for the examination of flowability, including static and dynamic methods applying empirical studies and the up-to-date chaos theory; however newest methods seem only to be powerful with the supplement of empirical principles. Our experiments try to refine both the technique of analysis and the methods by finding new, alternative ways. Our approach to the flowability measurements was to set up a dynamic time-dependent model which combines empirical observations and the chaos theory on a geometrical basis, thus find new aspects regarding flow properties of pellets and granules that could be relevant for drug developers.

Recent years have seen a rapid uptake in distributed energy resources (DER). Such technologies pose a number of challenges to network operators, which can ultimately limit the amount of rooftop solar photovoltaics (PV) systems that can be connected to a network. The objective of this industry-based research was to determine the potential network effects of forecast levels of customer owned rooftop solar PV on Energy Queensland’s distribution network and formulate functions that can be used to determine such effects without the requirement for detailed network modeling and analysis. In this research, many of Energy Queensland’s distribution feeders were modelled using DIgSILENT PowerFactory and analyzed with forecast levels of solar PV and customer load. Python scripts were used to automate this process and quasi dynamic simulation (QDSL) models were used to represent the dynamic volt-watt and volt-var response of inverters, as mandated by the Australian Standard AS/NZS 4777. In analyzing the results, linear regression was used to form trend equations that represent various network characteristics against the number of PV connections. The trend equations provide a way of approximating network characteristics for other feeders under various levels of customer owned rooftop solar PV without the need for detail modeling.

On 2013 the Villonaco wind farm (16.5 MW), the first wind farm in continental Ecuador near the city of Loja, began operations. The power generated is delivered to the National Interconnected System (SNI), which services the city. This research confronts two sets of real data, the electricity use of the urban area of Loja, and the power generated by the Villonaco Wind Farm. Electricity use follows clearly defined daily and weekly cycles, and wind power has a seasonal behaviour. The study shows that wind power integration cannot be a long-term stable power source regardless power or generation surplus. Another essential finding is that time series can be used as a statistical source to determine the need for short- (seconds) and long- (days, weeks) term energy storage. Strategies to further the energy autonomy of the urban area through the expansion of the wind farm by a factor of 2 are discussed.

This article introduces new method using ANN to control SVC in order to correct the source power factor of low voltage network. Two ANN approaches are investigated to design accurate and fast power factor correction (PFC) controller. First approach uses simple ANN (SANNA). Second approach uses cascaded ANN (CANNA). ANN regression, performance and the calculated error for both approaches are investigated to select between the two approaches. CANNA is selected as a better solution and it used to build the ANN PFFC controller using database, generated by MATLAB-Simulink, for standard three low voltage levels (240V, 220V and 110V). Nine test cases are carried out to validate the performance of proposed ANN PFC controller with a network has variable loads and low power factor (0.6 approximately). In order to extend the use of the controller to other voltage levels not included in the training process of the cascaded ANN, only the SVC is resized. Another nine cases are carried out with the same loads using the same ANN controller, as it is, to test its performance with the extended voltage level range (415V, 230V and 120V). The results show accurate and fast response in all test cases.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

This study will present a comprehensive review of the two-phase flow boiling heat transfer coefficient of hydrocarbons such propane (R-290), butane (R-600) and iso-butane (R-600a) and ethanol at various experimental conditions. Studying the multiphase flow heat transfer coefficient has a crucial importance for many heat transfer equipment to achieve higher efficiency for more compact design and cost reduction. One reason behind choosing hydrocarbons as refrigerants in this study is because hydrocarbons have zero ozone depletion potential (ODP=0) and insignificant direct global warming potential (GWP = 3). Moreover, thermodynamic and thermophysical characteristics of hydrocarbons qualify them to be a strong candidate for more heat transfer applications. Initially, by constructing a database for the working fluids from various experimental work available in the literature. The current data that this study has collected for the flow boiling of spans wide ranges of parameters, such as: mass flux, heat flux, operating pressure, and saturation temperature, etc. Furthermore, by comparing the experimental multiphase heat transfer coefficient database with the anticipated values of each correlation, the prediction performance of 26 correlations found in the literature was assessed. This study leads to the selection of the best prediction method based on the minimum deviation of predicted results from the experimental database provided by calculated mean absolute error (MAE) from the assessed correlations. The findings of this study can also be useful in the development of more accurate correlation methods for these fluids and improve the prediction of their flow boiling characteristics.

Power quality problem is a hot area in power systems and drives that has drawn the attention of many researchers. This is because of the threat it poses on the health of electrical systems and the cost incurred on utility bills. The problem arises as a result of the need for reactive power to be supplied alongside active power in power transmission and distribution. Unfortunately, reactive power is consumed by almost all components of the system, leading to a shortage. To solve this problem, there is a need to compensate for the lost reactive power. Several researchers have proposed various approaches to mitigate this problem such as thyristor switched capacitor bank, series compensator, series reactor, series var compensator (SVC), Static Synchronous Compensator (STATCOM), synchronous condenser and others. In order to further draw attention in this area, this work investigates a number of research papers on power compensation techniques and draw up challenges from each work that can be considered for further investigation. To this end, each research paper reviewed is evaluated in terms of problem solved, technique used, and results obtained. It therefore offers ample opportunities for researchers to explore in improving power quality and power system safety.

Risk-based redispatch optimization is proposed as a methodology to support the Transmission System Operator (TSO) with preventive remedial actions obtained by extending the security constrained unit commitment/economic dispatch with constraints resulting from the risk assessed for the power system. Although being heuristic, the methodology is based on comprehensive dynamic security assessment as time-domain simulations are used, allowing to express the degree of all types of instabilities, e.g., caused by contingencies, in monetary terms. Therefore, the risk is assessed as the expected value of the cost incurred by the TSO. Such approach forms a new pathway to including risk in planning procedures already used by TSOs. Results obtained for the IEEE39 dynamic power system, with costs assigned to load shedding and generator tripping due to single transmission lines short-circuits, are shown as a reference case.

This paper deals with the design, simulation and implementation of shunt hybrid compensator to maintain the power quality in 3-phase distribution networks feeding different types balanced and unbalanced nonlinear loads. The configuration of the compensator consists of a selective harmonic elimination passive filter, a series connected conventional 6-pulse IGBT inverter, acting as the active filter terminated with a dc link capacitor. The theory and modelling of the compensator based on current harmonic components at the load end and their decomposition in d-q axis frame of reference are utilized in the reference current generation algorithm. Accordingly, the source current waveform is made to follow the reference current waveform using a high frequency carrier based controller. Further, this inner current control loop is supported by a slower outer voltage control loop for sustaining desirable dc link voltage. Performance of the compensator is evaluated through MATLAB simulation covering different types of loads and reduction of harmonic currents and THD at the supply side along with excellent regulation of dc link voltage are confirmed. The performance of a hybrid compensator designed and fabricated using the above principles is evaluated and corroborated with the simulation results.

Integration of wind energy into the grid faces a great challenge regarding power quality. The International Electrotechnical Commission (IEC)~61400-21 standard defines the electrical characteristics that need to be assessed in a Wind Turbine (WT), as well as the procedure to measure the disturbances produced by the WT. One of the parameters to be assessed are voltage fluctuations or flicker. To estimate the flicker emission of a Wind Power Plant (WPP), the standard establishes that a quadratic exponent should be used in the summation of the flicker emission of each WT. This exponent was selected based on studies carried out in WPPs with type I and II WTs. Advances in wind turbines technology have reduced their flicker emission, mainly thaks to the implementation of power electronics for the partial or total management of the power injected into the grid. This work is based on measurements from a WPP with 16 type III WTs. The flicker emission of a single WT and of the WPP were calculated. Low flicker emission values at the Point of Common Coupling (PCC) of the WPP were obtained. The flicker estimation at the PCC, based on the measurement from a single WT, was analyzed using different exponents. The results show that a cubic summation performs better than the quadratic one in the estimation of the flicker emission of a WPP with type III WTs.

While microcredits are, by the development practitioners, repeatedly hailed as a useful measure of development policy, this empirical research in Bangladesh arrives at different results: the governing and disciplinary measures are necessary to trigger the best possible repayment success. Based on interviews with the microfinance beneficiaries, loan officers, and microfinance experts in Bangladesh, I chart some of the most frequently used governing and disciplinary techniques including fictitious proximity of loan officers, their fields of visibility and surveillance processes. The “success” of credit delivery is a neoliberal stance that ensures the ceaseless debt repayment process using the intentional and planned conduct, capitalizing social capital and credit honour reputation, surveillance over business enterprises, use of equivocal language and different forms of deception. The development strategy through microfinance in Bangladesh is a development “dispositif” with a changing shift in its declared social missions.

Optical micro-angiography (OMAG) is a new method of detecting flow rate and widely used for in vivo imaging. Although OMAG can distinguish between flowing and stationary parts, it cannot obtain accurate flow rate information. This study proposed a range formula for OMAG and the ultrahigh-sensitivity OMAG (UHS-OMAG) method to quantify the measurement range of an entire system. The parameters of the angle between beam scanning and flow directions, the angular velocity of the galvanometer, and the offset of incident light were introduced, and a formula for calculating the range was derived. Experiments were conducted to measure fine and ultra-fine flow rates by using OMAG and UHS-OMAG methods. The minimum measured flow rate was approximately 30 μm/s, and the maximum measured flow rate was approximately 8 mm/s. Experimental results are in good agreement with the preset results.

The Power Theory of Exchange and Money (PTEM) refines the economic neoclassical two-equation model of exchange. PTEM replaces the statistical average condition of exchange, which represents the equality of supply and demand for all transactions in the market, with a more specific equation of the equality of the generalized power of the parties in relation to their objects of exchange. The purpose of the article is to show the application of PTEM for the study of various social phenomena. Along with a brief summary of the main statements of this theory, its integration into the existing corpus of theories and ideas in economics and sociology is considered. The conclusions of power theory are then applied to consider the following topics: the objective motivation of exchange by the desire to increase power, the power nature of market equilibrium, the power nature of money, the accumulation of power through profit, the creation of money as a power act, the role of the state in the creation of money, the measure of power as a possible tool for social and political research.

Mechanical ventilation systems, which are used for breathing support when a person is not able to do it by their own, requires a device for measuring the air flow to the patient in order to monitoring and a assure the magnitude establish by a medical staff. Flow sensors are the conventional devices used for the air flow measuring; however, there were not available in Peru, because of the international demand during COVID-19 pandemic. In this sense, a novel air flow sensor based on orifice plate and an intelligent transducer stage were developed as an integrated design. Advanced methodologies in simulations and experiments using specially designed equipment for this application were carried out. The obtained data was used for a mathematical characterization and dimensions validation of the integrated design. The device was tested in its real working conditions, it was implemented in a breathing circuit connected to a low-cost mechanical ventilation system based on cams. Results indicate that the designed air flow sensor/transducer is a low-cost complete medical device for mechanical ventilators able to provide satisfactorily all the ventilation parameters air flow, pressure and volume over time by measuring the air flow and calculating the others. Furthermore, this device provides directly a filtered equivalent electrical signal for a display or a computer.

Considering the fault "N-1" checksum and the power flow, the single-phase power flow model is further transformed into a three-phase power flow model, and the asymmetry of the three-phase power flow is measured by the three-phase unbalance factor. The calculation model is linearized by the second-order cone relaxation and the Big-M method. At the same time, the load response and distribution network reconstruction are used to improve the reliability of the power supply network to cope with the power failure. The relationship between power supply capability and power flow constraints, main transformer capacity and distributed power parameters is analyzed by IEEE 33-node three-phase power distribution system. The feasibility of the proposed model and the accuracy of the second-order cone relaxation are verified by numerical examples, which provides a technical reference for distribution network planning.

Technological advancements must keep pace with earth’s rising demand for energy, while minimizing the carbon footprint on earth. One such option is using space based solar (SBS) radio frequency (RF) microwave power beaming. This innovative and novel technology is currently being explored to address terrestrial photovoltaic (PV) intermittency and provide a method to transmit power to other spacecraft in various orbits. This modality of power generation and distribution presents a new way to power terrestrial off-grid applications and earth orbiting spacecraft. In 1968, Dr. Peter Glaser published "Power from the Sun: Its Future", which serves as the foundation of this paper to revitalize scientific interest and efforts in this topic. This paper will primarily focus on the reliance of SBS initiatives on reusable launch vehicles (RLV) to place SBS spacecraft in a designated orbit, as well as the technological, economic, and operational challenges associated with power beaming to earth and other spacecraft. This includes a discussion of the variables from the operational environment that contribute or accelerate spacecraft end of life.

Computer systems that operate in remote locations such as satellites, remote weather stations and autonomous robots are highly limited in the availability of energy for their operation. This work aims to employ artificial intelligence algorithms in energy management in order to obtain the maximum energy yield and the prediction of energy availability to the system. The work presents the main types of algorithms used in artificial intelligence and presents the creation of a prototype that will operate as a low power system powered by batteries and a small solar plate, the prototype will perform inferences on the LSTM neural network algorithm in order to predict the future availability of energy, consequently the management system will carry out the energy distribution in order to obtain the maximum operation of the prototype without total discharge of the batteries. So that the artificial intelligence system could be embedded in the prototype, the TensorFlow Lite framework was used, which allows the inference to be carried out in devices with low consumption and limited processing power.

Imaging flow cytometry (ImFC) represents a significant technological advancement in the field of cytometry, effectively merging the high-throughput capabilities of flow analysis with the image-based features of microscopy. In this comprehensive review article, we take a historical perspective and delve into the evolution of this methodology, presenting its past, exploring current state-of-the-art and forecasting potential future advancements. The inception of ImFC arose from the innovative combination of a flow cytometer's hydraulics with the technology of an advanced camera. This synergistic coupling facilitated the morphological analysis of cell populations at a high-throughput scale, effectively evolving the landscape of cytometry. However, the application of ImFC faced several challenges. Among the most prominent ones, is the development and implementation of software systems that can reliably and efficiently handle the robust data acquisition and analysis inherent in ImFC. The scale and complexity of the data generated by ImFC necessitates the creation of novel analytical tools that can effectively manage and interpret this data, thus allowing us to unlock the full potential of ImFC. Interestingly, artificial intelligence (AI) algorithms have begun to be implemented on ImFC, offering a promise for enhancing analytical capabilities. The adaptability and learning capacity of AI may prove to be essential in knowledge mining from high-dimensional data produced by ImFC, potentially enabling more accurate analyses. Looking forward, we project that ImFC may become an indispensable tool, not only in research laboratories but also in clinical settings. Given the unique combination of high-throughput cytometry and detailed imaging offered by ImFC, we foresee a critical role for this technology in the next generation of scientific research and diagnostics. As such, we encourage both current and future scientists to consider the integration of ImFC as an addition to their research toolkit and clinical diagnostic routine.

Objectives: The purposes of this study were to 1) analyze the disruption of intracardiac flow by flow components and kinetic energy (KE) parameters in single ventricle physiology patients and compare with controls; 2) investigate left ventricular diastolic dysfunction in terms of 4D flow parameters in repaired Fontan (rFontan) group; 3) compare intracardiac flow parameters in morphologic LV and RV rFontan patient groups. Methods: Twenty-five rFontan patients (age: 10±3, M/F: 15/10) and fourteen controls (age: 10±2, M/F: 8/6) were prospectively recruited. All underwent cine and 4D flow cardiovascular magnetic resonance (CMR) on 3.0T scanner. Cardiac function and inter-ventricular mechanical dyssynchrony were analyzed using cine images. From 4D flow CMR, ventricular flow components were assessed: direct flow, retained inflow, delayed ejection flow and residual volume. Global and regional blood flow KE parameters, normalized to end-diastolic volume (EDV) were analyzed for functional single ventricle (FSV). Left ventricular (LV) diastolic dysfunction was assessed on echocardiography guidelines. Results: In comparison of rFontan vs. controls, median FSV residual volume (28% vs. 23%, P= 0.034) were higher in rFontan; median FSV direct flow (32% vs. 40%, P=0.005) and delayed ejection flow (17% vs. 24%, P=0.024) were lower in rFontan. FSV KEiEDV parameters were all lower in rFontan (all P<0.05). No significant differences were observed for flow components and KE parameters between patients with and without inter-ventricular dyssynchrony. FSV direct flow (AUC=0.76, Sensitivity=86%, Specificity=70%) was an independent predictor of LV diastolic dysfunction. Residual volume and E-wave KEiEDV were significantly different between morphologic RV and morphologic LV patient group. Conclusions: The changed flow pattern and decreased KE may be hemodynamic disturbances and impaired ventricular filling in rFontan patients. Reduced direct flow is associated with LV diastolic dysfunction. Morphologic right ventricular subgroup is worse than morphologic left ventricular group in terms of the intracardiac hemodynamics.

This study focuses on traffic condition analysis, especially in under developing country India and makes more visible of traffic flow by using traffic flow theory in order to understand real traffic condition. India is one of rapid economic growing countries and large market with second largest population 1.3 billion in 2018. On the other hand, there are social issues such as environment air pollution and global warming by traffic CO2 emission of transportation. This kind of condition is not only in India, but in other South East Asia and Africa in future. From recent more than one-month traffic observation in a typical major city Ahmedabad in Gujarat state, which has about 8 million population and industrialized city. In terms of traffic data collection, 14 CCTV cameras are used in the city. Based on multiple traffic cameras monitoring, author found the unique traffic flow characteristics and compares traffic flow theory. In this study, it is described what is key parameters to show real traffic congestion condition and how these congestion occurs.

The aim of this study is to model hydrodynamic processes of the Istanbul Strait with its stratified flow characteristic and calibrate the most important parameters using local and global search algorithms. For that two open boundary conditions are defined, which are in the North and South part of the Strait. Observed bathymetric, hydrographic, meteorological and water level data are used to set up the Delft3D-FLOW model. First, the sensitivities of model parameters on the numerical model outputs are assessed using PEST toolbox. Then, the model is calibrated based on the objective functions focusing on the flowrates of upper and lower layers. The salinity and temperature profiles of the Strait are only used for model validation. The results show that the calibrated model outputs of Istanbul Strait are reliable and consistent with the in-situ measurements. The sensitivity analysis reveals that the Spatial Low-Pass Filter Coefficient, Horizontal Eddy Viscosity, Prandtl-Schmidt Number, Slope in log-log Spectrum and Manning Roughness Coefficient are most sensitive parameters affecting flowrate performance of the model. The agreement between observed salinity profiles and simulated model outputs is promising whereas the match between observed and simulated temperature profiles is weak showing that the model can be improved particularly for simulating the mixing layer.

Hospital bed shortage is a worldwide concern. Beds unavailability has caused elective surgery cancellations, at our hospital peaking in spring 2016 at over 50%. This is often due to difficult patient step-down from intensive care (ICU) and high-dependency units (HDU). In our general/digestive surgery service admitting approximately 1000 patients yearly, ward rounds were run on a consultant firm basis. We report a quality improvement (ISRCTN13976096) introducing in our service a structured daily multi-disciplinary board round framework (SAFER Surgery R2G) adapted from the “SAFER patient flow bundle” and the "Red to Green days” approaches to enhance flow, comparing the previous year to 2017, when our framework was applied for 12 months.We used a Plan-Do-Study-Act (PDSA) methodology. Our intervention consisted in 1) systematic communication of the key care plan after the afternoon ward rounds to the nurse in charge; 2) 30’ 10AM Monday-to-Friday multidisciplinary board rounds, attended daily by the senior-team and weekly by hospital and site managers, revising the key care plan aiming at safe, early discharges, assessing the appropriateness of each inpatient day and tackling any cause of delay. We measured patient flow by average length of stay (LOS), ICU/HDU step-downs and operation cancellations count, monitoring safety through early 30-day readmissions. Compliance was assessed by board round attendance and staff satisfaction rate surveys.After 12 months (PDSA 2, N=1032), LOS significantly decreased from 7.2(±8.9) to 6.3(±7.4) days (p=0.003); ICU/HDU bed step-down flow increased by 9.3% from 345 to 375 (p=0.197), surgery cancellations dropped from 38 to 15 (p=0.100). 30-day re-admissions increased from 0.9% (N=9) to 1.3% (N=14)(p=0.390). Average cross-specialty attendance was 80%. Satisfaction rates were >75%, regarding enhanced teamwork and faster decisions.The SAFER Surgery R2G framework has shown an increase in patient flow in the context of an enhanced multidisciplinary approach, requiring senior staff commitment to remain sustainable.

The world is moving to the next phase of the energy transition with high penetrations of renewable energy. Flexible and scalable redox flow battery (RFB) technology is expected to play an important role in ensuring electricity network security and reliability. Continuous performance improvements will further enhance their value by reducing parasitic losses and maximizing available energy conversion over broader operating conditions. Concentration overpotentials from poor internal reactant distribution at high and low states of charge (SOC) limit power densities and are thus an important area of investigation. However, efforts to address these coupled electrochemical phenomena can compromise mechanical performance. Modelling and simulation of cell design innovations have shown it is possible to reduce losses from pump energy while increasing the availability of active species where required. The combination of wedge-shaped cells with static mixers investigated in this paper can reduce pressure drop and improve energy efficiency. Toroidal vanadium redox flow battery (VRB/VRFB) designs incorporating this innovation are presented for further development to improve community engagement with the technology.

Since the integration of electronic devices and intelligent electronic devices into the power grid, power quality (PQ) has consistently remained a significant concern for system operators and experts. Maintaining high standards of power quality is crucial to prevent malfunctions and faults in electric assets and in connected loads. Recently, PQ studies have shifted their focus to a specific frequency range, previously not considered problematic, the supraharmonic 2kHz–150kHz range. This range is not populated by the harmonic components of the 50-60 Hz mains fundamental, but a combination of intentional emissions, switching and non-linearity by-products and various types of resonances. This paper aims to provide a detailed analysis of the impact of SH on power network operation and assets, focusing on the most relevant documented negative effects, namely power loss and heating of grid elements, aging of dielectric materials, failure of medium voltage (MV) cable terminations, and interference to equipment and to power line communication (PLC) technology in particular. Under some shareable assumptions limits are derived and compared to existing ones for harmonic phenomena, providing a clear identification of the primary issues associated with supraharmonics and suggestions for the standardization process. Strictly related is the problem of grid monitoring and assessment of SH distortion, discussing the suitability of normative requirements for instrument transformers (ITs) with specific focus on their accuracy.

One of the challenges posed by renewable energies is the stabilization of parameters related to the quality of electrical energy. This study demonstrates the existence of a relationship between input blocks of hydropower and the variation of the fundamental frequency of the electricity grid. By mapping production data provided by Spanish Electric Network with frequency measured in the laboratory, it is shown that gradients of hydropower are correlated with frequency fluctuations for certain characteristic times. Considering hourly instances of energy input, the study compares two methods for calculating hydropower gradients (linear regression and pseudo-linear regression); and two methods for calculating local frequency extremes (the "specular inertia" method and analysis by comparison with the moving average), in order to corroborate the results.

The current revolution in communication and information technology is facilitating the Internet of Things (IoT) infrastructure. Wireless Sensor Networks (WSN) are a broad category of IoT applications. However, power management in WSN poses a significant challenge when the WSN is required to operate for a long duration without the presence of a consistent power source. In this paper, we develop a batteryless, ultra-low-power Wireless Sensor Transmission Unit (WSTx) depending on the solar-energy harvester and LoRa technology. We investigate the feasibility of harvesting ambient indoor light using polycrystalline photovoltaic (PV) cells with a maximum power of 1.4mW. The study provides comprehensive power management design details and a description of the anticipated challenges. The power consumption of the developed WSTx was 21.09µW during the sleep mode and 11.1mW during the operation mode. The harvesting system can harvest energy up to 1.2mW per second, where the harvested energy can power the WSTx for six hours with a maximum power efficiency of 85.714%.

This paper discusses recent developments in creep, over a wide range of temperature, that mqy change our understanding of creep. The five-power law creep exponent (3.5 to 7) has never been explained in fundamental terms. The best the scientific community has done is to develop a natural three power-law creep equation that falls short of rationalizing the higher stress exponents that are typically five. This inability has persisted for many decades. Computational work examining the stress-dependence of the climb rate of edge dislocations we may rationalize the phenomenological creep equations. Harper-Dorn creep, “discovered” over 60 years ago has been immersed in controversy. Some investigators have insisted that a stress exponent of one is reasonable. Others believe that the observation of a stress exponent of one is a consequence of dislocation network frustration. Others believe the stress exponent is artificial due to the inclusion of restoration mechanisms such as dynamic recrystallization or grain growth that is not of any consequence in the five power-law regime. Also, the experiments in the Harper-Dorn regime, which accumulate strain very slowly (sometimes over a year) may not have attained a true steady state. New theories suggest that absence or presence of Harper-Dorn may be a consequence of the initial dislocation density. Novel experimental work suggests that power-law breakdown may be a consequence of a supersaturation of vacancies which increase self-diffusion.

In this paper a variable’s involved in assessing the quality of a distributed generation system are reviewed, aiming to minimize the electric power losses (unused power consumption) and optimize the voltage profile. To provide this assessment, several experiments have been made to the IEEE 34-bus test case and various actual test cases with the respect of multiple DG units. The possibility and effectiveness of the proposed algorithm for optimal placement and sizing of DG in distribution systems have been verified. Finally, four algorithms were trailed: simulated annealing (SA), hybrid genetic algorithm (HGA), genetic algorithm (GA) and variable neighbourhood search. The HGA algorithm was found to produce the best solution at a cost of longer processing time.

This study aimed to enhance a micro hydroelectric generator system driven by free-flow vortex and to compare efficiency of Propeller and Crossflow turbines. Series of turbines in each type were designed and tested at water-flowrate of 0.02 m3/s. The turbine housing has 1 meter in diameter and 0.5-meter height with 2 meters outlet drain at the bottom. The best efficiency extracted from Crossflow turbines with the same height (0.3 meter) but different in diameter (0.4, 0.5, 0.6, and 0.7 meter) and numbers of blade (12, 18, 24, 30, and 23) was from an 18 blades turbine at 23.01% of efficiency. The best efficiency extracted from Propeller turbines with 5 blades was from a 0.4-meter-high turbine with a diameter of 0.7 meter at 13.92% of efficiency. There were 12 Propeller turbines designed in this study. They were different in height (0.2, 0.3, and 0.4 meter) and, in each height, 0.4, 0.5, 0.6, and 0.7 of diameter was applied. The result revealed that Cross Flow turbine had more efficiency to the system than Propeller turbine (9.09%) at the water-flowrate of 0.02 m3/s

Design criteria for coastal defenses exposed to wave overtopping are usually assessed by mean overtopping discharges and maximum individual overtopping volumes. However, it is often difficult to give clear and precise limits of tolerable overtopping for all kind of layouts. A few studies analyzed the relationship between wave overtopping flows and hazard levels for people on sea dikes, confirming that one single value of admissible mean discharge or individual overtopping volume is not a sufficient indicator of the hazard, but detailed characterization of flow velocities and depths is required. This work presents the results of an experimental campaign aiming at characterizing the flow characteristics associated to maximum individual overtopping volumes for an urbanized stretch of a town along the Catalan coast, where a walking and bike path and a railway run along the coastline are exposed to significant overtopping events every stormy season. The work compares different safety criteria for pedestrian. Results prove that safety of pedestrian on a sea dike can be still guaranteed even for overtopping volumes larger than 1000 l/m. Pedestrian hazard is rather proved to be linked to the combination of overtopping flow velocity and flow depth.

The basic equation for estimating the aerodynamic power captured by an Anderson Vertical Axis Wind Turbine (AVAWT) is a solution of the Navier-Stokes(N-S) equations for a baroclinic, inviscid flow. In a nutshell, the pressure difference across the AVAWT is derived from Bernoulli’s equation; an upshot of the integration of the N-S momentum equation for a baroclinic inviscid flow, Euler’s momentum equation. The resulting expression for the pressure difference across the AVAWT rotor is plotted as a function of freestream speed. Experimentally determined airstream speeds at the AVAWT inlet and outlet, coupled with corresponding freestream speeds are used in estimating the aerodynamic power captured. The aerodynamic power is subsequently used in calculating the aerodynamic power coefficient of the AVAWT. The actual power coefficient is calculated from the power generated by the AVAWT at various free stream speeds and plotted as a function of the latter. Experimental results show that, at all free stream speeds and tip speed ratios, the aerodynamic power coefficient is higher than the actual power coefficient of the AVAWT. Consequently, the power generated by the AVAWT prototype is lower than the aerodynamic power captured, given the same inflow wind condition.

The paper presents a modeling framework to analyze the effect of episodic rainfall supply on groundwater dynamics in the Ionian coastal plain multilayered aquifer. The focus is essentially on the short-term behavior of the shallowest layer, with a specific analysis on episodic rainfall events. In the studied aquifer, groundwater level responds sensitively to rainfall events, highlighting the presence of preferential recharge zones. The hydraulic head peak is a function of groundwater level antecedent to the rainfall event. A kinematic dispersion wave model was used to model infiltration processes via preferential pathways. A one-dimensional and non-linear particle based numerical model was developed. Particles with constant water volume travel according to celerity and hydraulic dispersion to simulate the infiltration rate wave through the vadose zone. The flow rate that reaches the water table represents the input function to determine groundwater level fluctuations along groundwater flow direction and according to the lithological features of the surficial levels of the multilayered aquifer, its storage capacity changes passing from unconfined to confined conditions. The model was validated with high time resolution time series of precipitation and groundwater level coming from Terra Montonata meteo-climatic and groundwater level monitoring station. The developed model represents a basis for evaluating and predicting groundwater discharge of the shallowest layers of the Ionian coastal multilayered aquifer under natural conditions including episodic rainfall.

Optical power splitters play a crucial role as the fundamental building blocks for many integrated optical devices. They should have low losses, broad bandwidth, and a high tolerance to fabrication errors. Adiabatic optical power splitters inherently possess these qualities while being compatible with foundry processes well-suited for mass-production. The long device lengths of adiabatic power splitters, however, are a limiting factor to achieve compact device sizes, which must be reduced. Here, we use a polynomial taper profile optimization algorithm to design 1×2 and 2×2 adiabatic power splitters with significantly shorter lengths than their adiabatic counterparts. The best performing 1×2 and 2×2 power splitters have 20 μm and 16 μm coupling lengths, respectively. Our designs have minimum feature sizes ranging from 140 nm to 200 nm, and our measurements averaged across 9 different chips show excellent consistency in performance for devices with 180 nm and 200 nm minimum features. Both the 1×2 and 2×2 adiabatic optical power splitters have excess losses less than 0.7 dB over a 100 nm bandwidth, with a standard deviation lower than 0.3 dB. Furthermore, our measurements show greater than 20 dB extinction ratios over 130 nm bandwidth. We also demonstrate the design of 1×2 power splitters with arbitrary splitting ratios, where splitting ratios ranging from 50:50 to 94:6 were achieved with standard deviations between 2% and 6%.

This study presents a cost-effective IoT-based remote monitoring system for solar PV energy systems, along with a machine learning-based PV power estimator. Remote access is crucial for tracking PV systems installed in remote areas. In this system, an open-source and IoT-compatible data logger is employed. The data logger collects important performance data of the PV system and transfers it to a server. Real-time visualization of this data is displayed in the designed web and mobile monitoring interfaces. The measured data includes the current, voltage, and temperature information of the PV generator and battery, as well as environmental parameters such as temperature, radiation, humidity, and pressure. Subsequently, this data is used for PV power estimation using machine learning methods. This enables the identification of maintenance requirements and the prediction of potential issues in the PV system. When a problem occurs in the PV system, the user is alerted through the mobile application. Early detection and intervention prevent power loss and damage to system components. When comparing the results of linear regression, SVM, decision trees, random forests, and KNN machine learning methods for power estimation based on performance evaluation criteria, it was observed that the random forests algorithm provided the best results. In conclusion, the developed monitoring and estimation system, along with web and mobile interfaces, is suitable for large-scale PV energy systems.

Proper management of solar energy, as an effective renewable source, is of high importance toward sustainable energy harvesting. This paper offers a novel sophisticated method for predicting solar irradiance (SIr) from environmental conditions. To this end, an efficient metaheuristic technique, namely electromagnetic field optimization (EFO) is employed for optimizing a neural network. This algorithm quickly mines a publicly available dataset for non-linearly tuning the network parameters. To suggest an optimal configuration, five influential parameters of the EFO (i.e., N_Pop, R_rate, Ps_rate, P_field, and N_field) are optimized by an extensive trial and error practice. Analyzing the results showed that the proposed model can learn the SIr pattern and predict it for unseen conditions with high accuracy. Furthermore, it provided about 10% and 16% higher accuracy compared to two benchmark optimizers, namely shuffled complex evolution and shuffled frog leaping algorithm. Hence, the EFO-supervised neural network can be a promising tool for the early prediction of SIr in practice. The findings of this research may shed light on the use of advanced intelligent models for efficient energy development.

In most studies reported in literature, a flat, constant coefficient is used to convert the amount of optical power required at the input of an optical link into the effective power consumption. This constant coefficient approach is very simple to apply but not accurate, since laser efficiencies are dependent on the optical output power in addition to the operating temperature. In this paper the relationship between laser wall plug efficiency and optical power output is investigated and the effect of this variance on optical links and on-chip laser source electric power consumption is presented

The ubiquitous diffusion of Power Electronic Converters (PECs) in many fields of application including traction and energy conversion is suggesting the possibility of new and better integration of advanced power conversion and ICT services. This work investigates the possible advancements in the use of optical fibers for control of PECs, using Plastic Optical Fiber. The optical communication link connects the switching control to the converter control, following the line of separation between the expertises of the power electronic engineer and the control engineer. Control wise, the PEC becomes a black box compatible with any off-board controller, now immune from the Electromagnetic Interference (EMI) produced by the power switches. The redundant optical link is ready for the high switching (and sampling) frequencies possible with the use of SiC power semiconductor devices (100 kHz+). Distributed control of multiple PEC units and advanced telemetry for diagnostics and prognostics are targeted. A proof-of-concept demonstrator is presented and tested. Moreover, the possible evolution towards a power electronic cloud with remote management and orchestration is described.

The interaction between the grid network and the offshore wind power plant (WPP) network can lead to the amplification of certain harmonics and potentially resonant conditions. Offshore WPP should limit the increment of harmonic voltage distortion at the point of connection to the grid network as well as within their internal network. The harmonic distortion should be limited within the planning level limits using harmonic compensation, which is usually achieved by using static filters. In this paper an active damping compensation strategy with a STATCOM using emulation of resistance at the harmonic frequencies of concern is analysed. Such a compensation is effective for the local bus, though the performance is not guaranteed at the remote bus. This paper investigates the challenges associated with remote harmonic compensation in the offshore WPP, which is connected to the onshore grid through long high-voltage cables and transformers. First, the harmonic distortion and the compensating effects of the filter are theoretically assessed. Afterwards, they are demonstrated using harmonic propagation studies and time domain simulations in PSCAD.

A supply chain management (SCM) system is a strategic cooperative that organically integrates all supply chains to improve the performance of a company. The greatest critical success factor of SCM is partnership. Without cooperation between companies, SCM performance is limited. Does this imply, therefore, that companies within the supply chain can achieve mutual transactions equally? If the power between companies is unequal, how does this affect their partnership? The focus of this study is to assess whether power types enhance SCM performance through partnerships. We categorize power types as mediated and non-mediated. Mediated power is categorized based on coercion, reward, and legitimate, while non-mediated power is categorized based on information, expert, and reference. Therefore, this study examines how power types form a causal partnership relationship within the supply chain, and performs an empirical investigation on how the partnerships influence SCM performance.

Heart attacks and strokes are one of the leading causes of death in the world today, and heart attacks caused by clogged arteries that carry blood to the heart muscle are a significant part of these strokes. These are caused by the accumulation of fat particles in the walls of the arteries and the reduction of blood flow through it over a long process. The process of fat penetration in the underlying layers of the Artery wall has been the focus of many researchers, and various researches and Simulations have been done on it, in each of them, the effect of specific parameters has been considered. In the present study, the effect of blood flow rate on the flow pattern in a bifurcate artery with two ducts has been investigated using FLUENT software with Computation fluid dynamic Method. The effect of the angle between the two ducts of the Artery on the flow pattern has been investigated.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of simulation and statistical results of EO with other optimization techniques showed that EO is more effective and superior.

Debris flows have generated major disasters worldwide due to their great destructive capacity, which is associated with their high energy levels and short response times. To achieve an adequate risk management of these events, it is necessary to define as accurately as possible the different hazard levels to which the territory is exposed. This article develops a new methodology to estimate this hazard based on the hydrodynamic characteristics of the flow and the granulometry of the sediments that can be mobilized by the flow. The hydrodynamic characteristics of the flow are determined through a mathematical modeling that considers the rheology of non-Newtonian flows and the different volumes of sediments that could be transported during events corresponding to different return periods. The proposed methodology was implemented in the Jamundí River basin (Colombia). The results obtained indicate that in the upper part of this basin there is a low hazard level, while in the lower part of the basin approximately 15% of the affected territory has a medium hazard level and the remaining 85% has a low hazard level. The methodology developed is simple to implement but technically rigorous since it considers all relevant aspects in the generation of debris flows.

The two-phase flow of water and reactive gas in the channel of proton exchange membrane fuel cell (PEMFC) plays an important role in high-quality water management. In this study, the removal effect of 3D wave channel and 2D straight channel for liquid water was studied by volume of fluid method. The dynamic behavior of droplet emerge from the gas diffusion layer (GDL) into the channel under the influence of gas flow was investigated. The effects of droplet growth, deformation, detachment, force, pore size on water critical behavior and water content in the channel are discussed. The results show that the 3D wave channel is superior to the removal of liquid water than the 2D straight channel. The increase of velocity is conducive to the discharge liquid water. While infinite increase of velocity will cause more parasitic power loss. The larger pore size of GDL is not advantageous to the performance of PEMFC, but the appropriate increase of pore size is conducive to the discharge of liquid water. The basic knowledge obtained in this study will help to deepen the understanding of droplet dynamics in PEMFC gas channels, and help to optimize the design and working conditions of these channels.

Dams design and their operation cause strong environmental alteration and therefore a long-term debate is ongoing for the scale of these projects. At the same time, the concept of Environmental Flow Assessment (EFA) is a crucial element of modified ecosystems featuring large infrastructure such as dams and reservoirs for mitigating potential environmental degradation while they operate. Nowadays, integrated scientific frameworks are required to quantify the risks caused by large infrastructure. Through the use of stochastic analysis, it is possible to quantify these uncertainties, and present a solution that incorporates long-term persistence and environmental sustainability into a balanced reservoir simulation model. In this work, an attempt is made to determine a benchmark reservoir size incorporating hydrological and ecological criteria though stochastic analysis. The primary goal is to ensure the best possible conditions for the ecosystem, and then secondarily to allow a steady supply of water for other uses. Using a synthetic timeseries based on historical inputs, it is possible to determine and preserve essential statistical characteristics of a river’s streamflow, and use these to detect the optimal reservoir capacity that maximizes environmental and local water demand reliability.

Unsteady flow is the most common and complicated form of fluid motion in nature. This paper takes the beaches of key waterways in the middle and lower reaches of the Yangtze River as the research object, analyzes the water surface distribution and average flow velocity distribution near the beach, and analyzes the differences. The relationship between the flow pattern of the steep slope and the water flow pattern of the entire survey area and the steep slope of the beach and its nearby water flow structure. The water flow near the beach is divided into four major blocks: the swelling water area, the falling water area, the backwater area and the maximum flow rate area. The water flow structure characteristics and the cause of each block are analyzed.

Widely used in hydraulics, the Colebrook equation for flow friction relates implicitly to the input parameters; the Reynolds number, Re and the relative roughness of inner pipe surface, ε/D with the output unknown parameter; the flow friction factor, λ; λ=f(λ, Re, ε/D). In this paper, a few explicit approximations to the Colebrook equation; λ≈f(Re, ε/D), are generated using the ability of artificial intelligence to make inner patterns to connect input and output parameters in explicit way not knowing their nature or the physical law that connects them, but only knowing raw numbers, {Re, ε/D}→{λ}. The fact that the used genetic programming tool does not know the structure of the Colebrook equation which is based on computationally expensive logarithmic law, is used to obtain better structure of the approximations which is less demanding for calculation but also enough accurate. All generated approximations are with low computational cost because they contain a limited number of logarithmic forms used although for normalization of input parameters or for acceleration, but they are also sufficiently accurate. The relative error regarding the friction factor λ, in best case is up to 0.13% with only two logarithmic forms used. As the second logarithm can be accurately approximated by the Padé approximation, practically the same error is obtained also using only one logarithm.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

In this paper, new N-way Wilkinson power dividers (WPDs) are represented by using slow-wave structures such as narrow slits loaded and meandered transmission lines. The slit loaded and meandered lines are used to represent the quarter wavelength transmission lines of a conventional WPD for size reduction. Based on the proposed approaches, 2-, 4- and 8-way power dividers are designed, simulated and fabricated. The fabricated -, 4- and 8-way circuits have been measured at the center frequencies of 2.03, 1.77, and 1.73 GHz in an excellent agreement with the predicted ones. The meandered transmission lines are also used to design new types of WPDs having novel input/output port arrangements. For this purpose, two 3-way WPDs are located at both sides of the same board so as to have different power splitting ratios at different inputs and outputs to provide alternative solutions for antenna arrays. Furthermore, a 5-way dual layer WPD is introduced by locating the meandered transmission lines to two layers. The proposed 3- and 5-way WPDs allow halving the input power at the next output port in the order of P/2, P/4, P/8, P/16, and P/16. All of the designed power halving WPDs have been simulated, fabricated and successfully tested.

In the development of power systems it is indicated very often, that transformation of power systems should be carried out in accordance with the idea of energy democracy. This will develop energy communities, that are trying to meet energy needs by using local renewable generation sources. This may result with a temporary low load on the MV lines connecting the community grid and the power system. Such state may cause incorrect operation of power protection systems. This can cause an extended protection operation time, due to decision algorithms inactivity at low values of measurement currents. Therefore, the detailed MV lines overcurrent digital protection model and a dynamic model of the power network were developed. The simulation results are showing that the settings of the parameters activating the protection decision algorithms affect their operation time in dynamic conditions. The conclusion is that the development of the power protection automatics must be carried out in the same time (preferably in advance) with the change of the power system operation model. This is very important for future power systems with high penetration energy communities and renewable generation sources.

A decade ago, non-radiative wireless power transmission reemerged a promising alternative to deliver electrical power to devices where a physical wiring proved to be unfeasible. However, conventional coupling-based approaches are neither scalable nor efficient when multiple devices are involved, as they are restricted by factors like coupling and external environments. Zenneck waves are excited at interfaces, like surface plasmons and have the potential to deliver electrical power to devices placed on a conducting surface. Here, we demonstrate, efficient and long range delivery of electrical power by exciting non-radiative waves over metal surfaces to multiple loads.Our modeling and simulation using Maxwells equation with proper boundary conditions shows Zenneck type behavior for the excited waves and are in excellent agreement with experimental results. In conclusion, we physically realize a radically different power transfer system, based on a wave, whose existence has been fiercely debated for over a century.

The conceptual reconstruction of Neiwan powerhouse is one of the key activities under the current ongoing mapping project of Taiwanese hydropower plants that mainly took place between 2013 and 2015 and is now focused on micro, pico, and historical power plants. Judging from the fact that the oldest hydropower plant in Taiwan named Guishan starts its operation in 1905, Neiwan powerhouse was among the very first powerhouses that were built across the island to support the electrification of Taiwan. However, the main function of the single turbine equipped Neiwan micro powerhouse was to support mainly the military needs and protect the territories occupied by Japanese troops. Since the powerhouse was built in 1909 and operates only something about 10 year there are very little physical materials or evidence along with contemporaries. Therefore the further reconstruction is based mainly on physical observation of the remains located at the site, old photographs, related articles, treatises and typology of mechanical and civil constructions of other hydropower plant cases in Taiwan hence this paper´s main intention is to pitch a concept reconstruction rather than definite conclusion.

This research paper is part of the wider project concerning the very first detailed mapping of the overall Taiwanese hydro-power plants that took place from 2013 up to 2015 and it is currently in evaluation and finalization stage. The case of Shanping hydro-power plant has been carefully studied, photographed, documented and mapped in situ. It was one of the isolated hydro-power plant projects originally built to supply the remote area with the specific designation. Shanping hydro-power plant, as well as the other units from the early hydro-power generation era in Taiwan, are considered to be the technological heritage of civil and mechanical engineering that reflects later in all the further projects up to nowadays modern Taiwanese hydro-power plants. Unfortunately, most of the hydro-power houses from the older periods were severely damaged or destroyed by natural causes which were also the case of Shanping unit. The research is trying to reconstruct the original location of the powerhouse and its supporting structures based on available historical documents, previous studies, comparative methodology, and the current on-site observation.

To reduce solar power production invariance, it is critical to study varying patterns of power production in the concerned region. Analyzing the patterns of past power production trends can help simulate power production scenarios for future. The current study area is around Amsterdam, located in Netherlands. PVoutput.org website is used to mine 6 months of solar power production data for 120 stations around Amsterdam city. FME Workbench software is used to actively fetch the data from the mentioned website and manage in a MySQL database. Solar attenuation maps created using ArcGIS, helped to graphically visualize the variations in solar power production at different times and locations. Further, spatial autocorrelation is checked between the stations using semi-variograms in geostatistical tool of ArcMap. This feature allows to check whether the stations located close to each other are more correlated to each other rather than stations which are far apart. The statistical data analysis of power production can aid solar power production companies to better interpolate and predict solar power in advance for the concerned study region.

In this paper, we present the extension of the pressure-based solver designed for the simulation of compressible and/or incompressible two-phase flows of viscous fluids. The core of the numerical scheme is based on the hybrid Kurganov— Noele — Petrova/PIMPLE algorithm. The governing equations are discretized in the conservative form and solved for velocity and pressure, with the density evaluated by an equation of state. The acoustic-conservative interface discretization technique helps to prevent the unphysical instabilities on the interface. The solver was validated on various cases in wide range of Mach number, both for single-phase and two-phase flows. The numerical algorithm was implemented on the basis of the well-known open-source Computational Fluid Dynamics library OpenFOAM in the solver called interTwoPhaseCentralFoam. The source code and the pack of test cases are available on GitHub: https://github.com/unicfdlab/hybridCentralSolvers

Partial shading on solar photovoltaic (PV) arrays is a prevalent problem in photovoltaic systems that impair the performance of PV modules and is responsible for reduced power output as compared to that in standard irradiance conditions thereby resulting in the appearance of multiple maximas on panel output power characteristics. These maxims contribute to mismatch power losses among PV modules. The mismatch losses depend on shading characteristics together with different interconnected configuration schemes of PV modules. The research presents a comparative analysis of partial shading effects on a 4 x4 PV array system connected in series(S), parallel (P), serries-parallel (SP),total-cross-tied (TCT),central-cross-tied(CCT),bridge-linked(BL),bridge-linked total cross-tied (BLTCT) ,honey-comb(HC), honey-comb total-cross-tied (HCTCT) and ladder (LD) configurations using MATLAB/Simulink. The PV module SPR-X20-250-BLK was used for modeling and simulation analysis. Each module is comprised of 72 number of PV cells and a combination of 16 PV modules was employed for the contextual analysis. Accurate mathematical modeling for the HCTCT configuration under partial shading conditions (PSCs) is provided for the first time and is verified from the simulation. The different configuration schemes were investigated under short-narrow,short-wide,long-narrow,long-wide, diagonal, entire row distribution, and entire column distribution partial shading condition patterns with mathematical implementation and simulation of passing clouds. The performance of array configurations is compared in terms of maximum power generated ), mismatch power loss (∆), relative power loss ) and the fill factor (FF). It was inferred that on average, TCT configuration yielded maximum power generation under all shading patterns among all PV modules interconnection configurations with minimum mismatch power losses followed by hybrid and conventional PV array configurations respectively.

(1) Background: Conventional strength training and core exercises are commonly prescribed to improve cycling performance. Although previous studies have explored the utility of strength training in various cycling populations, this intervention has never been compared to core exercises; (2) Methods: 36 trained road cyclists were divided in 3 groups of 12 participants that performed either no strength training, conventional strength training or core exercises, in all cases together with their regular cycling training during a 12-week period. Peak power outputs across different durations (5 seconds, 60 seconds, 5 minutes, and 20 minutes) were recorded before and after the intervention; (3) Results: Conventional strength training is superior to core training and no strength training for all measured durations. At the same time, core training results in improved 5 second power output when compared to no strength training, while all the other measures are comparable among groups; (4) Conclusions: Conventional strength training is superior to core exercises and no strength training in trained road cyclists, and accordingly, it is recommended that this population incorporates strength training during their regular weekly workouts.

The turbulent Poiseuille flow between two parallel plates is one of the simplest possible physical situations, and it has been studied intensively. In this paper, we propose a modified Prandtl-van Driest mixing length that satisfies both boundary conditions and wall damping effects. With our new formulations, we numerically solve the problem and, moreover, propose an approximate analytical solution of mean velocity. As applications of our solution, an approximate analytical friction coefficient of turbulent Poiseuille flow is proposed.

The problem of fluid dynamics can be greatly simplified if, for every point in space, the strain-rate tensor is diagonalized. This tensor is introduced into the Navier-Stokes equations via material law and divergence of the stress tensor. This article shows that local SO(3)xU(1) gauge fields can be used to locally diagonalize the diffusion components of the strain-rate tensor. The gauge fields resulting from the connection can be interpreted as convection components of the flow, they show properties of quasiparticles and can be interpreted as elementary vortices. Thus, the proposed approach not only offers new insights for the solution and situative simplification of the Navier-Stokes equations, it also uncovers hidden symmetries within the flow convection, allowing - depending on boundary conditions - further interpretation.

Aero-fuel centrifugal pumps are important power plants in aero-engines. Unlike most of the existing centrifugal pumps, a combination impeller is integrated with the pump to improve its performance. First, the critical geometrical parameters of combination impeller and volute are given. Then, the effects of combination impeller on flow characteristics inside the impeller and volute are clarified by comparing simulation results with that of the conventional impeller, where the effectiveness of selected numerical method is validated by an acceptable agreement between simulation and experiment. Finally, the experiment is performed to test the external performance of studied pump. A significant feature of this study is that the flow characteristics are significantly ameliorated by reducing the flow losses emerged in impeller inlet, impeller outlet and volute tongue. Correspondingly, the head and efficiency of combination impeller are higher with comparison to conventional impeller. Consequently, it is a promising approach in ameliorating flow field and improving external performance by applying a combination impeller to an aero-fuel centrifugal pump.

Deformation flows are flows incorporating shear, strain and rotational components. These flows are ubiquitous in the geophysical flows, such as the ocean and atmosphere. They appear near almost any salience, such as isolated coherent structures (vortices and jets), various fixed obstacles (submerged obstacles, continental boundaries). Fluid structures subject to such deformation flows may exhibit drastic changes in motion. In this review paper, we focus on the motion of a small number of coherent vortices embedded in deformation flows. Problems involving isolated one and two vortices are addressed. When considering a single-vortex problem, the main focus is on the evolution of the vortex boundary and its influence on the passive scalar motion. Two vortex problems are addressed with the use of point vortex models, and the resulting stirring patterns of neighbouring scalars are studied by a combination of numerical and analytical methods from the dynamical system theory. Many dynamical effects are reviewed with emphasis on the emergence of chaotic motion of the vortex phase trajectories and the scalars in their immediate vicinity.

Day by day, the share of renewable energy-based power plants such as offshore wind farms and photovoltaic power plants, in the present-day power systems is escalating. Nevertheless, most of these power-producing facilities have been located quite far away from the load centers. At this stage, HVDC power systems provide satisfactory options due to qualities such as reduced line losses, substantial controllability, and environmental advantages. Nevertheless, unique converter designs are required to combine asynchronous HVDC networks with each other and with already existing high voltage alternating current (HVAC) networks. In this study, based on the above special cases, a unique DC-DC modular multilevel converter (MMC) architecture is presented that provides an excellent solution for both integrating modern asynchronous HVDC networks and integrating these modern HVDC power systems with existing asynchronous HVAC power systems. The mathematical analysis of the recommended DC-DC MMC design has been examined in detail and the power transfer between two asynchronous power grids has been realized in a simulation environment. Efficient bilateral power transmission has been made achievable by the control system. The recommended DC-DC MMC topology has shown to be a highly successful approach, in the interconnection of HVDC power systems, according to the simulation results.

A new power receiving unit (PRU) is proposed in this paper for the resonant wireless power transfer (WPT), which is characterized by the capability of attracting high power from the power transmitting unit (PTU). The resonant WPT is designed for delivering the electrical power to the PRU attached on an electrical vehicle (EV) chassis 50cm away from a PTU installed on the ground. The proposed PRU uses only the passive elements such as inductors, diodes and the capacitors, which needs no initial power from the EV. It is then applicable for charging a battery to several hundred volts for even a first-time charging battery. At a switching frequency of the resonant WPT in the experiment being 4MHz, the proposed PRU behaves itself as a negative impedance converter (NIC) in the subharmonics of 4MHz. The NIC effect plus the subharmonic oscillation causes an instability current charging the battery connected to the PRU. In this paper, we simulated the PRU and performed the experiment. The experiment demonstrates a battery charging of 150W from 50cm away using three D-mode GaN HEMT transistors via the instability current ramp. The power transfer efficiency (PTE) improved as the power delivered to load (PDL) goes higher. The best power transfer efficiency (PTE) is 65% in the present findings. The simulation analysis shows that the circuit allows itself be used to much higher power transfer when it is implemented with more GaN HEMT transistors connected in parallel. The theoretical derivation of the PRU circuit is also used to support both the experimental and simulation results.

A layout of urban waste fired zero emission power plant is described in this paper. The principle of layout, which comes from similar coal-fired plants retrieved from the literature, integrates gasification with a power generation section, and implements two parallel conversion processes, one supplied by the heat of the gasifier consisting of a thermoacousticmagnetohydrodynamic (TAMHD) generator, while in the second one the syngas is treated in order to obtain almost pure hydrogen, which is fed to fuel cells. The CO2 deriving from the oxidation of Carbon base is stocked in liquid form. The novelty of the proposed layout lies in the fact that the entire conversion is performed without solid moving parts. The resulting plant avoids any type of emissions in the atmosphere, increases mechanical efficiency as compared to traditional plants, thanks to the absence of moving parts, nonetheless, resolving at its root the ever-increasing waste-related pollution problems.

Harmonic resonances are part of the Power Quality (PQ) problems of electrified railways and have serious consequences for the continuity of service and integrity of components in terms of overvoltage stress. The interaction between Traction Power Stations (TPSs) and trains that causes line resonances is briefly reviewed showing the dependence on infrastructure conditions. The objective is real-time monitoring of resonance conditions seen first of all from the onboard panto-graph interface, but it is equally applicable at TPS terminals. Voltage and current spectra, and de-rived impedance and power spectra, are analyzed proposing compact and efficient methods based on Short-Time Fourier Transform, suitable for real-time implementation with the hardware avail-able for energy metering and harmonic interference monitoring. The methods are tested by sweeping long recordings taken at some European railways, covering cases of longer and shorter supply sections, with a range of resonance frequencies of about one decade. They give insight into the spectral behavior of resonances, their dependency on position and change over time, and criteria to recognize genuine infrastructure resonances from rolling stock emissions.

Over the last decades, the energy market around the world has reshaped due to accommodating the high penetration of renewable energy resources. Although renewable energy sources have brought various benefits, including low operation cost of wind and solar PV power plants, and reducing the environmental risks associated with the conventional power resources, they have imposed a wide range of difficulties in power system planning and operation. Naturally, classical optimal power flow (OPF) is a nonlinear problem. Integrating renewable energy resources with conventional thermal power generators escalates the difficulty of the OPF problem due to the uncertain and intermittent nature of these resources. To address the complexity associated with the process of the integration of renewable energy resources into the classical electric power systems, two probability distribution functions (Weibull and lognormal) are used to forecast the voltaic power output of wind and solar photovoltaic, respectively. Optimal power flow, including renewable energy, is formulated as a single-objective and multi-objective problem in which many objective functions are considered, such as minimizing the fuel cost, emission, real power loss, and voltage deviation. Real power generation, bus 13 voltage, load tap changers ratios, and shunt compensators values are optimized under various power systems’ 14 constraints. This paper aims to solve the OPF problem and examines the effect of renewable energy resources 15 on the above-mentioned objective functions. A combined model of wind integrated IEEE 30-bus system, solar 16 PV integrated IEEE 30-bus system, and hybrid wind and solar PV integrated IEEE 30-bus system are performed 17 using the equilibrium optimizer technique (EO) and other five heuristic search methods. A comparison of 18 simulation and statistical results of EO with other optimization techniques showed that EO is more effective 19 and superior.

Since its introduction almost 50 years ago, the concept of ‘flow’ has been descriptive of optimal experiences, also in relation to play. However, the explorative nature of play leads to some discrepancies between flow and the optimal experience of play. In this paper the differences between flow and play are explored, leading to proposing the state of ‘wonder’ (directed at exploration) as an alternative to ‘flow’. From this perspective, the study further explores how we may design toys that enable meaningful experiences of play, identifying opportunities in designing for toys as the enablers of immersed experiences of wonder.

There is a long standing ‘two times problem’ in that a satisfactory reconciliation between the time of physics and that of psychology has not been realized. A partial solution to the past/present/future phenomenon has been successfully given by the Hartle information gathering and processing system (IGUS) view. That model IGUS robot is enhanced here for the entire ‘two times problem’ to deal with not only the temporal experiences of the flow of time but also those of manifest time. A dualistic robot is proposed which has a veridical system of temporal experiences that are compatible with various spacetime cosmologies. It also has an illusory system of corresponding temporal experiences. This dualistic IGUS robot was made possible by discovering temporal experience within the brain that correspond to those of physics. The dualistic theory suggests that the veridical system, as a result of evolution, begets the illusory system to enhance behavioral adaptation. Thus, there is just one fundamental physical time which the brain does, indeed, possess and then enhances with illusory counterparts. Therefore, there should no longer be a need to reify illusory temporal experiences as modern spacetime cosmologies tend to do. Physical time already resides within human time.

In this study, the author proposes to evaluate the effect of sales growth, Receivable Turnover and operating cash flow on the liquidity of PT. Unilever Indonesia Plc. The research method used is descriptive method with a quantitative approach. In this statement, the population used in this study is the financial statement data from PT. Unilever Indonesia Plc. from 2010 to 2018, the technique of determining the sampling uses Purposive Sampling. This research data uses secondary data from PT. Unilever Indonesia Plc financial statements from 2010 to 2018. All data sources were obtained from the website of the Indonesia Stock Exchange at https://www.idx.co.id, the company's website and Google search. Our analysis reveals that sales growth and accounts receivable turnover from PT. Unilever Indonesia Plc. has no influence on the liquidity of PT. Unilever Indonesia Plc, while operating cash flow has an influence on the Liquidity of PT Unilever Indonesia Plc. This means the ups and downs of the value of sales and accounts receivable turnover of a company has no influence on the liquidity of PT. Unilever Indonesia Plc, while operating cash flow has increased or decreased has an influence on the liquidity of PT Unilever Indonesia Plc. The value of sales growth, accounts receivable turnover and operating cash flow can explain the liquidity of PT Unilever Indonesia Plc. by 78%, while 22% is explained by other factors which are not included in this study.

Rainfall is the main driver of hydrological processes in dryland environments and characterising the rainfall variability and processes of runoff generation are critical for understanding ecosystem function of catchments. Using remote sensing and in situ data sets, we assess the spatial and temporal variability of the rainfall, rainfall-runoff response, and effects of antecedent soil moisture and ground cover at different spatial scales on runoff coefficients in the Upper Burdekin catchment, northeast Australia, which is a major contributor of sediment and nutrients to the Great Barrier Reef. The high temporal and spatial variability of rainfall exerts significant controls on runoff generation processes. Rainfall amount and intensity are the primary runoff controls, and runoff coefficients for wet antecedent conditions were higher than for dry conditions. The majority of runoff occurred via surface runoff generation mechanisms, with subsurface runoff likely contributing little runoff due to the intense nature of rainfall events. At annual to seasonal temporal scales and for relatively large catchments, we could not detect a significant effect of ground cover on runoff. We conclude that in the range of moderate to large catchments (193 – 36,260 km²) runoff generation processes are sensitive to both antecedent soil moisture and ground cover. A higher runoff-ground cover correlation in drier months with sparse ground cover highlighted the critical role of cover at the onset of the wet season and how runoff generation is more sensitive to cover in drier months than in wetter months. The monthly water balance analysis indicates that runoff generation in wetter months (January and February) is partially influenced by saturation overland flow, most likely confined to saturated soils in riparian corridors, swales, and areas of shallow soil. By March and continuing through October, the soil ‘bucket’ progressively empties by evapotranspiration, and Hortonian overland flow becomes the dominant, if not exclusive, flow generation process. The results of this study can be used to better understand the rainfall-runoff relationships in dryland environments and subsequent exposure of coral reef ecosystems in Australia and elsewhere to terrestrial runoff.

Power semiconductor devices are essential from the operation point of view, size, efficiency and cost, these components are used in a myriad of applications, providing features that make them an important part of the system in which they are operating. This document analyzes and compares the basic structure, properties, design aspects, as well as temperature performance, stability and switching losses, present in devices on silicon (Si), silicon carbide (SiC) and new generation devices fabricated in gallium nitride (GaN) applied in renewable energy systems. The main objective is determinate the viability of the new generation components, which present a superior performance in view of an increase in efficiency, conductivity, decreases in switching losses, lower resistances and parasitic capacitances as well as higher operating frequency range. Therefore demonstrating the GaN components are a strong and viable candidate to solve some of the problems present in renewable energy systems.

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

The transformation of the states of polarization of electromagnetic waves that interact with polarimetrically linear media can be represented by means of the associated Mueller matrix. A global measure of the ability of a linear medium to modify the states of polarization of incident waves, due to any combination of enpolarizing, depolarizing and retarding properties, is introduced as a distance of the Mueller matrix to the identity matrix. This new descriptor, called the polarizing power, is applicable to any Mueller matrix and can be expressed as a function of the degree of polarimetric purity and the trace of the Mueller matrix. The graphical representation of the feasible values of the polarizing power provides a general view of its main peculiarities and features. The values of the polarizing power for several typical devices are analyzed.