The creation of nano-zero-valent iron (nZVI) by implementing plant extracts is an environmentally friendly process. High antioxidant capacity and phenol content indicated the possibility of oak-nZVI synthesis using oak leaf extract as a stable material with minimal agglomeration. Simultaneously removal of Cd and phosphates and Ni and phosphates was optimized by a statistically designed experiment with a definitive screening design. In terms of significance, 4 input parameters on process productivity were monitored: initial metal concentration (1 - 9 mgL-1), initial ion concentration (1- 9 mgL-1), pH value (2 - 10) and oak-nZVI dosage (2 - 16 ml). Phosphate removal efficiency, in the presence of cadmium, was the most influenced by oak-nZVI dose and cadmium concentration, while pH gave three statistically significant interactions with oak-nZVI dosage, cadmium concentration, and phosphate concentration. Phosphate removal efficiency, in the presence of Ni, is the most influenced by nickel concentration, phosphate concentration, pH, two-factor interaction between nZVI dose and Ni concentration, and quadratic phosphate interaction. The process optimization yielded the highest simultaneous removal efficiency of 98.99% and 87.30% for cadmium and phosphate ions, respectively. Also, the highest simultaneous removal efficiency of nickel and phosphates ion was 93.44% for 96.75%, respectively. The optimization process fits into the confidence intervals, confirming the assumption that the adopted regression model describes the process well. This work demonstrated an enormous potential and prosperous application for the Cd(II), Ni(II), and phosphate removal from water matrices.

In pursuit of carbon neutrality, the demand for metals that are necessary for the development of clean energy technologies is rapidly increasing. Metallurgical waste, such as slag, presents a promising secondary source of these key metals. This research aims to develop an eco-friendly hydrometallurgical process to recover Cu, Ni, and Co from discarded copper/nickel slag. The high-pressure acid leaching (HPAL) was used to selectively leach Ni, Cu, and Co from the fayalite slag, yielding high leaching efficiencies of 99.9%, 89.4%, and 99.9%, respectively, with low Fe and Si tenors to the pregnant leach solution (PLS). The solvent extraction (SX) technique utilizing LIX 984N was used to selectively extract and enrich copper from the dilute PLS to about 23 g/L Cu with a very low Fe concentration of 0.05 g/L. Potassium amyl xanthate (PAX) solution was used to form Ni and Co xanthate complexes from the raffinate solution. Nickel was selectively recovered using ammonia solution, while cobalt xanthate complex was thermally decomposed and recovered as cobalt oxide solids of about 25 wt.% Co. A comprehensive process flowsheet is presented, furthermore, to realize the real application of the developed slag cleaning process, a preliminary economic evaluation was performed.

In this experimental work, pure nickel oxide and Al-doped NiO thin films have successfully been elaborated onto glass substrates by solar spray pyrolysis technique. The substrates were heated at around 450°C using a solar heater (furnace). The structural, optical and electrical properties of the elaborated Al-doped films have been studied at different atomic percentage ratios (0, 0.5, 1, 1.5 and 2 at. %). The results of Al-doped NiO films XRD patterns were, the formation of (NiO) phase under a cubic crystalline structure (polycrystalline) with a strong favored orientation along (111) plane were noticed at all sprayed films. When Al doping ratio reaches 1 at.%, an growth in crystallite size over 31.9 nm was obtained denoting the nano-structure of the product, which confirmed by SEM images. In addition, aluminum oxide Al₂O₃ was clearly observed at 1.5 at.% Al ratio. Otherwise, all thin films have a good optical transmission in the visible region of about 65%, the optical band gap energy decreased from 3.69 to 3.64 eV with increasing Al doping ratio. It is shown that the layer deposited with 0.5 at.% has less disorder with few defects. The investigation on electrical properties of elaborated thin films confirmed that the conductivity of NiO films was improved, after doping them with Al which affirms their p-type character of semiconductor. However, an addition of an excessive quantity of Al content causes the formation of Al₂O₃ which leads to a decrease in the conductivity. It is worth mentioning that the Al content of 0.5 at.% is the optimum ratio in terms of electrical conductivity and formation defect. Al-doped NiO can be used in various optoelectronic devices due to its good transparency and high electrical conductivity.

Laser shock peening as an innovative surface treatment technology can effectively improve the fatigue life, sur-face hardness, corrosion resistance, and residual compressive stress. Compared with the laser shock peening, the warm laser shock peening (WLSP) is a new surface treatment technology to improve materials’ surface performances, which takes advantage of thermal mechanical effects on stress strengthening and micro-structure strengthening, results in more stable distribution of the residual compressive stress under heating and cyclic loading process. In this paper, the microstructure of GH4169 nickel super-alloy processed by WLSP technology with differ-ent laser parameters were investigated. The proliferation and tangling of dislocations in GH4169 were observed and the dislocation density increased after WLSP treatment. The influences of different treatment by LSP and WLSP on the microhardness distribution of the surface and along cross-sectional depth were investi-gated. The microstructure evolution of the GH4169 alloy being shocked with WLSP were studied by TEM. The effect of temperature on the stability of high temperature microstructure and properties of GH4169 alloy WLP was investigated.

Inclusions in steels and alloys are known as factors that could lower deformation, mechanical, corrosion and other properties. Study of inclusions in nickel based alloys is important since these materials could suffer from corrosion degradation in harsh operational conditions, where inclusions could lead to a pitting initiation. For estimation of a harmful effect of different inclusions on corrosion resistance of Ni-based alloys, inclusion characteristics (such as composition, morphology, size, number and location) on film filter and dissolution of metal matrix around different inclusions on surfaces of metal samples after electrolytic extraction (EE) were investigated in two samples of industrial Ni-based alloys (alloy 718 and EP718). It was found that both Ni-based alloys have various inclusions: carbides (large size NbTi-C and small multicomponent carbides), nitrides TiNb-N and sulfides (TiNb-S in EP718 alloy). The higher harmful effect on corrosion resistance of metal was detected around sulfides and small carbides containing Mo, W, Cr. Dissolution effect was also observed around large carbides and nitrides, especially around inclusions having size more than 10 µm. Moreover, the dissolution of metal matrix around inclusions and clusters located on the grain boundaries is 2.1-2.7 times larger compared to that for those inclusions inside of grains of the given alloy samples.

The rapidly evolving field of additive manufacturing requires a periodic assessment of the progress made in understanding the properties of metallic components. Although extensive research has been undertaken by many investigators, the data on properties such as hardness from individual publications are often fragmented. When these published data are critically reviewed, several important insights that cannot be obtained from individual papers become apparent. We examine the role of cooling rate, microstructure, alloy composition, and post process heat treatment on the hardness of additively manufactured components. Hardness data for steels and aluminum alloys processed by additive manufacturing and welding are compared to understand the relative roles of manufacturing processes. Furthermore, the findings are useful to determine if a target hardness is easily attainable either by adjusting AM process variables or through appropriate alloy selection.

Crystalline phase engineering is a prominent strategy for synergistically optimizing the sur-face-body phases of a catalyst. In this work, TiO2 nanosheets assembled into nanotubes (TNSTs) with two-phases of anatase and rutile were firstly synthesized via crystal engineering by simple thermal annealing, and subsequently loaded with Ru nanoparticles to create efficient benzene hydrogenation catalyst Ru/TNSTs. The well- designed nanosheet-tubes structure boasts large specific surface area and excellent transmission channels, which effectively prevents the ag-glomeration and deactivation of loaded Ru nanoparticles, as well as promotes the internal diffu-sion in the reaction process of benzene hydrogenation to cyclohexene. Furthermore, titanium dioxide nanosheet-tubes contain numerous Ti3+ defects, which not only improves the overall generation rate of cyclohexene, but also enhances the suppression of cyclohexene adsorption. Most importantly, the two-phases of titanium dioxide increases the ratio of the electron defi-ciencies of Ru and promotes cyclohexene desorption. These synergistic properties enhance the selectivity and efficiency of the Ru/TNSTs catalysts, resulting in excellent performance in the hydrogenation of benzene to cyclohexene. Especially the Ru/TNSTs-4 catalyst achieves a 95% in-itial selectivity and 51% yield of cyclohexene in the reaction, outperforming most supported Ru-based catalysts. This work may provide new perspectives for designing efficient benzene hydrogenation catalysts via crystalline phase engineering.

The utilization of titanium dioxide (TiO2) as a photocatalyst for the treatment of wastewater has attracted significant attention in the environmental field. Herein, we have prepared a NH2-MIL-125-derived TiO2@N-doped C Visible Light Catalyst through an in-situ calcination method. The nitrogen element in the organic connector is released through calcination, simul-taneously doping into the sample, thereby enhancing its spectral response to cover the visible region. The as-prepared TiO2@N-doped C catalyst exhibited preserved cage structure even after calcination, thereby alleviating the optical shielding effect and further augmenting its photo-catalytic performance by increasing the reaction sites between the catalyst and pollutants. The calcination time of the TiO2@N-doped C-450 °C catalyst was optimized to achieve a balance be-tween the TiO2 content and nitrogen doping level, ensuring efficient degradation rates for basic fuchsin (99.7%), Rhodamine B (89.9%), and tetracycline hydrochloride (93%) within 90 minutes.

The electron Transport layer (ETL) plays a crucial role in solar cell technology, particularly in perovskite solar cells (PSCs), where nanostructured TiO2 films have been investigated as superior ETL’s compared to compact TiO2. In this study we explore the nanocolumnal growth of TiO2 in the anatase phase, for bilayer thin films by magnetron sputtering (MS) technique and glancing angle deposition (GLAD). By optimizing the growth parameters, we achieved the formation of TiO2 nanocolumns with a cross-sectional diameter ranging from 50 to 75 nm. The average thickness of the films exceeded 12.71 ± 0.5µm , while the filaments exhibited an inclination angle close to 70◦ , corresponding to the deposition angle. Furthermore, we observed a correlation between the quality of the initial layer and enhanced growth of the TiO2 nanocolumns.

Vertically aligned Fe, S, and Fe-S doped anatase TiO₂ nanotube arrays are prepared by electrochemical anodization process using an organic electrolyte in which lactic acid is added as an additive. In the electrolyte, nanotube layers of greater length (12 μm) and high order with inner diameter of approx. 90 nm and outer diameter of approx. 170 nm are achieved. Doping of Fe, S, and Fe-S via simple wet impregnation method substituted Ti and O sites with Fe and S, which leads to enhance the rate performance at high discharge current densities. Discharge capacities of TiO₂ tubes increased from 82 mAh g-1 (bare) to 165 mAh g-1 for Fe-S doped TiO₂ at high current densities of 0.3 mAcm-2 after 100 cycles with exceptional capacity retention of 85% after 100 cycles. Owing to the enhancement of thermodynamic and kinetic properties by doping of Fe-S, Li-diffusion increas2ed resulting in remarkable discharge capacities of 143 mAh g-1 and 89 mAh g-1 at a current density of 7.4 mA cm-2 and 19 mA cm-2, respectively.

Indonesia is one of the largest banana producing countries in the world remaining abundance solid waste of banana fruit bunch. The banana fruit bunch contains high natural fibers which were obtained by an impregnation process using potassium hydroxide (KOH) and followed by a carbonization process under steam at 250°C for 5 h. The nanomaterial of TiO₂/fibre was prepared by a hydrothermal process at 200°C for 4 h. Surface morphology proved that the TiO₂ was loaded into the fibre by an increasing roughness of the surface and irregular size of porosity. The development of amorphous to crystalline phase of TiO₂/fibre was clearly observed. The effectiveness of TiO₂/fibre for removal of rhodamine B was investigated from different parameters of adsorptions in aqueous solution. The equilibrium adsorptions show that the Langmuir and Freundlich isotherm exhibited the best correlation coefficient (R² > 0.94) relating to the chemisorption and physisorption interaction in the adsorption process. Kinetic models were well described by the pseudo-first and second-order with the best correlation coefficient (R² > 0.99). These results indicate that nanomaterial TiO₂/fibre can be used as an effective adsorbent for removal of rhodamine B in aqueous solution.

In order to improve the strength of PVA/xylan composite films and endow them with ultraviolet (UV) shielding ability, TiO2-KH550 nanoparticle was synthesized and added into the PVA/xylan matrix. The TiO2-KH550 nanoparticle dispersed well in the 0.04% sodium hexametaphosphate (SHMP) solution under ultrasonic and stirring treatments. Investigations on the properties of films showed that TiO2-KH550 had the positive impact on improving the strength, moisture and oxygen barrier properties of the composite films. The maximum tensile strength (27.3 MPa), the minimum water vapor permeability (2.75×10-11 g•m-1•s-1•Pa-1) and oxygen permeability (4.013 cm3•m-2•24h-1•0.1MPa-1) were obtained under the addition of 1.5% TiO2-KH550. The tensile strength of TiO2-KH550 reinforced composite film was increased by 70% than that of the pure PVA/xylan composite film, and the water vapor and oxygen permeability were decreased by 31% and 41%, respectively. Moreover, the UV transmittance of film at the wavelength of 400 nm was almost zero when adding 1.5~2.5% of TiO2-KH550, which indicated the PVA/xylan composite films were endowed with excellent UV light shielding ability.

This study concerns calculation and comparison of Fe, Co, Ni and Cu deposition rates in tungsten codeposition process based on electrodeposition of numerous tungsten alloys. 8 different tungsten alloys containing from 2 to 5 metals were electrodeposited in constant conditions in order to compare exact reduction rates. Calculated rates enabled control of the alloy composition precise enough to obtain a high-entropy WFeCoNiCu alloy with well-balanced composition. Introduction of copper to form the quinternary alloy was found to catalyze the whole process, increasing deposition rates of all components of the high-entropy alloy.

Three types of the composites were tested for electromagnetic interference (EMI) absorption shielding effectiveness, curing process and physical-mechanical properties. In the first type of composites, manganese-zinc ferrite, nickel-zinc ferrite, and both fillers in their mutual combinations were incorporated into acrylonitrile-butadiene rubber. The overall content of the filler, or fillers combinations was kept on 200 phr. Then, carbon black, or carbon fibres, respectively were incorporated into each rubber formulation in constant loading - 25 phr, while the content of magnetic fillers was unchanged - 200 phr. The work was focused on the understanding of correlation among electromagnetic shielding parameters and electrical conductivity of composites in relation to their EMI absorption shielding effectiveness. The absorption shielding ability of materials was evaluated within the frequency range from 1 MHz to 6 GHz. The study revealed good correlation among permittivity, conductivity, and EMI absorption effectiveness. Although, the absorption shielding efficiency of composites filled only with ferrites seems to be the highest, the absorption maxima of those composites were reached over 6 GHz. The application of carbon based fillers resulted in higher electrical conductivity and higher permittivity of composites, which was reflected in their lower absorption shielding performance. Though, the composites with filled with ferrites and carbon based fillers absorbed electromagnetic radiation within the desired frequency range. The presence of carbon based fillers caused the improvement in tensile behavior of composites. The study also demonstrated that the higher was the ratio of nickel-zinc ferrite in magnetic fillers combinations, the higher was the absorption shielding performance.

This study presents a combined electrochemical impedance spectroscopy (EIS) and atomic force microscopy (AFM) and Scanning Kelvin Probe Force Microscopy(SKPFM) investigation on the natural passivation process of stainless steels (AISI 316 and AISI 304) and nickel-based alloy (INCONEL 600) as a function of immersion time in an alkaline medium (pH = 13). EIS measurements show an increase in the resistance of the film with increasing immersion time in the electrolyte. After 3 days of immersion, for the three alloys, the films formed constitute an effective barrier to the dissolution of the alloys as shown by AFM and SKPFM. The oxide film growth on each substrates is only influenced by trenches formed during the polishing step and don’t depend on the chemical composition.

A comparative study of the physicochemical properties of natural bentonite clays of Pogodayevо (Republic of Kazakhstan, mod.1) and Dash-Salakhli (Republic of Azerbaijan, mod.2) deposits and modification of the bentonite clay with polyhydroxocations of iron (III) and aluminium (III). It-wasestablished that the modification of natural bentonitesusing polyhydroxocations of iron (III) and aluminium(III) by the method of "co-precipitation" leads to a change in their chemical composition, structural and sorption properties. The results showed that hydroxy-aluminum cations ([Al3O4(OH)24(H2O)12]7+) and poly-hydroxyl-Fe or polyoxo-Fe were intercalated into clay layers, which led to an increase in the values of d001 and specific surface areas compared to those of the original bentonite, from 37 to 120 for the Pogodaevo bentonite and from 51 to 172 respectively for bentonite from the Dash-Salakhli deposit. It is shown that modified sorbents based on natural bentonite are finely porous objects with a predominance of pores of 1.5−6.0 nm in size. As a result, there is a significant increase in the specific surface area of sorbents. Modification of bentonite with polyhydroxocations of iron (III) and aluminium (III) by the "co-precipitation" method also leads to an increase in the sorption capacity of the sorbents obtained with respect to nickel (II) cations. Modified bentonites were used for the adsorption of Ni (II) ions from the model solution. Ni (II) was absorbed in a neutral pH solution. The study of equilibrium adsorption showed that the data are in good agreement with the Langmuir isotherm model. The maximum adsorption capacity of the Ni (II) monolayer obtained from the Langmuir equation was 25.0 mg/g (mod. 1_Al_5-c), 18.2 mg/g (mod. 2_Al_5-c) for Al-bentonite and 16.7 mg/g (mod. 1_Fe_5-c), 10.1 (mod. 2_Fe_5-c) for Fe-bentonite. The kinetics of adsorption is considered. The high content of Al-OH anion exchange centresin them determines the higher sorption activity of Al-modified bentonites.

The paper investigates the influence of ion nitriding on the microstructure, corrosion resistance, and tensile strength at elevated temperatures of Haynes 282 nickel superalloy specimens produced by the Direct Metal Laser Sintering-DMLS technique. Analysis of the specimens’ surface morphology revealed that the ion nitriding process significantly affects the physical and chemical phenomena occurring on the surface of the specimens. Phase composition and stress analysis showed that Haynes 282 nickel alloy specimens produced by the DMLS technique and a chromium nitride layer produced in the ion nitriding process have tensile stress. The layer is also characterized by high nanohardness compared to specimens produced using the classical method (wrought) and DMLS technique. The conducted corrosion resistance tests confirmed the positive effect of the nitrided layer on the corrosion resistance of Haynes 282 nickel alloy produced by the DMLS technique. The ion nitriding process did not significantly affect the elevated-temperature tensile strength of Haynes 282 nickel alloy specimens produced by the DMLS technique.

Difficult-to-cut materials are being increasingly used in many industries because of their superior properties, including high corrosion resistance, heat resistance and specific strength. However, these same properties make the materials difficult to machine using conventional machining techniques. Laser-assisted milling (LAM) is one of the effective methods for machining difficult-to-cut materials. In laser-assisted milling machining occur after the workpiece is locally preheated using a laser heat source. Laser assisted machining has been studied by many researchers on flat workpiece or micro end-milling. However, there is no research on the curved shape using laser assisted milling. This study investigated the use of laser assisted milling to machine a three-dimensional curved shape workpiece based on NURBS. A machining experiment was performed on Inconel 718 using different tool paths (ramping, contouring) under various machining conditions. Finite elements analysis was conducted to determine the depth of cut. Cutting force, specific cutting energy and surface roughness characteristics were measured, analyzed and compared for conventional and LAM machining. LAM significantly improved these machining characteristics, compared to conventional machining. There results can be applied to the laser-assisted machining of various three-dimensional shapes.

The integration of clean energy generation with wastewater treatment holds promise for addressing both environmental and energy concerns. Focusing on photocatalytic hydrogen production and wastewater treatment, the study introduces PdIn/TiO2 catalysts for the simultaneous removal of the pharmaceutical contaminant paracetamol and hydrogen production. Physicochemical characterization showed a high distribution of Pd and In on the support as well as a high interaction with it. The Pd and In deposition enhances the light absorption capability and significantly improved HER in comparison to TiO2 not only in the electrolyte but also in presence of paracetamol. Regarding PTM oxidation, TiO2 and PdIn/TiO2 showed an irreversible behavior toward the PTM oxidation, limited by the adsorption of species on the electrode surface. Thus, PdIn-doped TiO2 stands out as a promising catalyst, showcasing enhanced physicochemical properties and superior catalytic performance. This underscores its potential for both environmental remediation and sustainable hydrogen production.

The method of micro-arc oxidation has been utilized to synthesize a protective biocompatible coating for a bioresorbable orthopedic Mg implant. This paper presents the results of a comprehensive research of micro-arc coatings based on diatomite – a biogenic material consisting of shells of diatom microalgae. The main focus of this study was the functionalization of diatomite-based micro-arc coatings by incorporating the particles of titania (TiO2) into them. Various properties of the resulting coatings were examined and evaluated. The XRD analysis has revealed the formation of a new magnesium orthosilicate phase – forsterite (Mg2SiO4). It has been established that the corrosion current density of the coatings has decreased by 2-4 orders of magnitude after the inclusion of TiO2 particles, depending on the coating process voltage. The adhesion strength of the coatings has increased following the particle incorporation. The processes of dissolution of both coated and uncoated samples in a sodium chloride solution were studied. The in vitro cell viability was assessed, which showed that the coatings significantly reduce the cytotoxicity of Mg samples.

The physiological characteristics of liquid digestate retrieved from various biogas plants based in northern Greece are presented. Preliminary photocatalysis experiments on inoculated liquid di-gestate sampled showed that disinfection is possible when pre-treated digestate with a combination of centrifuge-flocculation-μFiltration after 5.5 hours of 0.7g/L suspended TiO2 under UVA illumination for the experimental conditions is used. A novel design photocatalytic nanofiltration reactor was implemented for disinfection experiments on pre-treated liquid digestate, giving promising results. This work sets the basis for the efficient operation and engineering application of technology collaboration with photocatalysis as the final step for liquid digestate sanitation and reusable water recovery.

Wound infections evidently appeared in times of World War I that accounted a significant mortality and morbidity rate among injured soldiers. Currently, around 11 million people worldwide require medical treatment for wound infections and 300,000 die every year due to untreated wound infection. The extensive use of antibiotics to treat wound infection leads to emerging new microbial strains that are resistant to many antibiotics. There is a growing concern on the emergence and re-emergence of drug-resistant pathogens such as multi-resistant bacterial strains. Hence, the development of new antimicrobial compounds or the modification of those that already exist to improve antibacterial activity is a high priority area of research. During the past few decades, nanotechnology has arisen with new promising technology for synthesis of nanobiomaterials. Metallic nanoparticles (NPs) are considered as new alternative treatment with superior antibacterial activity. In this study, new formulation of titanium oxide (TiO2) NPs with different sizes were synthesized and characterized. Genotoxicity, mutagenicity and antibacterial activities of TiO2 NPs against the causative agents of wound infection were investigated. Antibacterial activity of TiO2 NPs was conducted against three ATCC ® bacterial strains: methicillin-resistant Staphylococcus aureus (MRSA), Escherichia coli and Pseudomonas aeruginosa. The results clearly illustrate a superior antibacterial activity of all newly formulated TiO2 NPs against the most causative agents of wound infection. Most of our TiO2 NPs showed non-genotoxic and non-mutagenic results at the maximum concentrations. Findings of this study will enhance the future of the therapeutic strategies against the resistant pathogenic strains that cause wound infections.

According to research, we have learned that Mg and TiO2 are new types material of marine protective coatings. We found that the addition of Mg can improve the performance of Zn-Al coating passivation film, and TiO2 has excellent photocatalytic self-cleaning performance. In this paper Zn-Al pseudo alloy coating was prepared by cold spray technique, and Zn-Al-Mg-TiO2 pseudo alloy composite coating was prepared by adding Mg and nano-TiO2. The effects of Mg and TiO2 to the marine protective properties of Zn-Al coatings were studied by friction and wear test, dynamic salt water corrosion test, electrochemical test, scanning electron microscope(SEM), energy dispersive spectrometer(EDS) and super deep scene 3D microscope. The results show that the addition of Mg and nano-TiO2 not only fills the gap of the coating and improves the density of the coating, but also generates grid-like flocculent corrosion products on the surface of the coating which can gather other corrosion products to improve the density of corrosion products, reduce the friction coefficient and corrosion rate of the coating surface, effectively prevent the invasion of Cl- in solution, and improve the wear and corrosion resistance of the coating.

Chromium-nickel austenitic stainless steels are widely used due to their high corrosion resistance, good weldability and deformability. To some extent, their application is limited by their mechanical characteristics. As a result of their austenitic structure, increasing the static and dynamic strength of the components can be achieved by surface cold work. Due to the tendency of these steels to undergo intercrystalline corrosion, another approach to improve their mechanical characteristics is the use of low-temperature thermo-chemical diffusion processes. This article proposes a new combined process based on sequentially applied diamond burnishing (DB) and low-temperature gas nitriding (LTGN) to optimally improve the fatigue strength of 304 steel. The essence of the proposed approach is to combine the advantages of the two processes (DB and LTGN) to create a zone of residual compressive stresses in the surface and subsurface layers–the enormous surface residual stresses (axial and hoop) introduced by LTGN, with the significant depth of the compressive zone characteristic of static surface cold working processes. DB (both smoothing and single-pass hardening), in combination with LTGN, achieves a fatigue limit of 600 MPa, an improvement of 36.4% compared to untreated specimens. Individually, smoothing DB, single-pass DB and LTGN achieve 540 MPa, 580 MPa and 580 MPa, respectively. It was found that as the degree of plastic deformation of the surface layer introduced by DB increases, the content of the S-phase in the nitrogen-rich layer formed by LTGN decreases, with resultant increased content of -phase, and a new (also hard) phase: stabilized nitrogen-bearing martensite.

Composites of Ag and TiO2 nanoparticles on cotton fabrics were synthetized in-situ by sono-chemical and hydrothermal methods achieving the successive formation of Ag-NPs and Ti-NPs directly on the fabric. The impregnated fabrics were characterized by ATR-FTIR spectroscopy, high resolution microscopy (HREM), scanning electron microscopy coupled with Ener-gy-dispersive X-ray spectroscopy (SEM-EDS), Raman, photoluminescence, UV-vis and DRS spectroscopies and by tension tests. Results showed the successful formation and impregnation of NPs on the cotton fabric, with a negligible leaching of NPs after several washing cycles. The photocatalytic activity of supported NPs was assessed by the degradation of methyl blue dye (MB) under solar and UV irradiation revealing improved photocatalytic activity of the Ag-TiO2/cotton composites due to a synergy of both Ag and TiO2 nanoparticles. This behavior is attributed to a diminished electron-hole recombination effect in the Ag-TiO2 cotton samples. The biocide activity of these composites on the growth inhibition of Staphylococcus aureus (Gram+) and Escherichia coli (Gram-) was confirmed, revealing interesting possibilities for the utilization of the functionalized cotton fabric as protective cloth for medical applications.

In the past decade, under the background of the carbon peaking and carbon neutrality era, the rapid development of new energy vehicles has put forward higher requirements for the performance of strike forces such as battery cycle life, energy density and cost. Lithium-ion batteries have gradually become the mainstream of electric vehicle power batteries due to their excellent energy density, rate performance and cycle life. At present, the most widely used cathode materials for power batteries are lithium iron phosphate (LFP) and ternary nickel-cobalt-manganese (NCM). However, these materials exhibit the bottlenecks that limit the improvement and promotion of power battery performance. In this review, the performance characteristics, cycle life attenuation mechanism (including structural damage, gas generation and active lithium loss, etc.) and improvement methods (including surface coating and element-doping modification) of LFP and NCM batteries are reviewed. Finally, the development prospects of this field are proposed.

The application of diffusion dialysis using various types of ion-exchange membranes for the separation of sulfuric acid and nickel sulfate has been evaluated. The process of dialysis separation of a real waste solution from an electroplating facility containing 252.3 g/L of sulfuric acid, 20.9 g/L of nickel ions and small amounts of zinc, iron, copper ions, etc. has been studied. Heterogeneous cation-exchange membrane containing sulfo groups and heterogeneous anion-exchange membranes with different thicknesses (from 145 μm to 550 μm) and types of fixed groups (4 samples with quaternary amino groups and 1 sample with secondary and tertiary amino groups) are used. The diffusion fluxes of sulfuric acid, nickel sulfate, and the total and osmotic fluxes of the solvent are determined. The use of a cation-exchange membrane does not allow separation of the components, since the fluxes of both components are low and comparable in magnitude. The use of anion-exchange membranes makes it possible to efficiently separate sulfuric acid and nickel sulfate. At the same time, the thin dialysis membrane turns out to be the most effective, as well as the membranes with quaternary amino groups, and the membrane with secondary and tertiary amino groups proved to be the least effective.

Sputtered reactive multilayers applied as a heat source in electronic joining processes are an emerging technology. Their use promises low-stress assembly of components while improving the thermal contact and reducing the thermal resistance. Nanostructured surface modifications can significantly enhance adhesion and reliability of joints between different materials. This work examines reactive multilayer of nickel and aluminum, directly sputtered on nanostructured black silicon surfaces and compares their phase transformation with reference samples deposited on pristine silicon surface. The investigation of the quenched self-propagating reaction reveals a clear influence of the nanostructured surface on the prolongation of the phase transition. Rapid thermal annealing tests result in the formation of Al_1.1Ni_0.9 phase. The nanostructured interface seems to hinder the full transformation of the parent material. The surface modification improves the adhesion of the formed alloy on silicon surfaces and can possibly increase the reliability of joints based on reactive aluminum/nickel multilayer. The use of black silicon, a nanostructured surface modification, is thus a promising approach to realize reliable multi-material joints in complex systems.

Transparent binder is used to substitute conventional black asphalt binder and to provide light-colored pavements, whereas nano-TiO2 has the potential to promote photocatalytic and self-cleaning properties. Together, these materials provide multifunction effects and benefits when the pavement is submitted to high solar irradiation. This paper analyses the physicochemical and rheological properties of a transparent binder modified with 0.5%, 3.0%, 6.0%, and 10.0% of nano-TiO2 and compares it to the transparent base binder, and conventional and polymer modified binders (PMB) without nano-TiO2. Their penetration, softening point, dynamic viscosity, master curve, black diagram, Linear Amplitude Sweep (LAS), Multiple Stress Creep Recovery (MSCR), and Fourier-Transform Infrared Spectroscopy (FTIR) were obtained. The transparent binders (base and modified) seem to be workable considering their viscosity and exhibited values between the conventional binder and PMB regarding rutting resistance, penetration, and softening point. They showed similar behavior as the PMB, demonstrating signs of polymer-modification. The addition of TiO2 seems to reduce fatigue life, except for the 0.5% content. Nevertheless, its addition in high contents increases the rutting resistance. The TiO2 modification seems to have little effect on the chemical functional indices. The best percentage of TiO2 was 0.5%, considering fatigue and 10.0% concerning permanent deformation.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

In this work, a systematic study was conducted on the fabrication of multi-material components obtained employing Laser-Powder Bed Fusion (L-PBF) technology. The idea of making multi-material components is a winning capability of additive technologies because it allows the fabrication of Functionally Graded Materials (FGMs) with the customization of parts according to different required properties. The transition from one material to another was achieved gradually and continuously within the same layer using ad-hoc equipment designed for L-PBF systems with a powder spreading technique based on coaters or rollers. The influence of the relative position of the different materials within the powder chamber and the geometry of the developed equipment on the metallurgical and mechanical properties of the manufactured samples was evaluated. The performed tests involved the use of two materials, a nickel-based superalloy, and a stainless steel, having different chemical, physical and mechanical properties to obtain gradual properties variation in the manufactured samples. Based on the results of post-process characterization obtained through metallographic, chemical, and mechanical analysis, the relative positions of the materials and the geometry of the developed equipment have a limited effect on the sample’s manufactured properties. The characteristics of the FGM zone depend on the nature of the employed powders, and its extent coincides with that defined during the design of the divider.

The effects of heating rate before solution treatment and cooling rate after solution treatment on the morphological distribution and evolution of precipitation phase of nickel-based single crystal superalloy were studied. The dissolution, precipitation and growth of precipitation phase and matrix phase during heat treatment were analyzed by means of high power scanning electron microscopy. The results show that the morphology of precipitated phase has nothing to do with the distribution of precipitated phase and the heating rate in the heating process, but the cooling rate in the cooling process affects the shape, size and distribution of precipitated phase. The faster the cooling rate, the smaller the precipitated phase is, the more irregular the shape is, the smaller the equivalent edge length is, and the smaller the channel width of matrix phase is.

Immobilized metal affinity chromatography (IMAC) is a popular and valuable method for the affinity purification of polyhistidine-tagged recombinant proteins. However, it often shows practical limitations, which might require cumbersome optimizations, additional polishing, and enrichment steps. Here, we present functionalized corundum particles for the efficient, economical, and fast purification of recombinant proteins in a column-free format. The corundum surface is first derivatized with the amino silane APTES, then EDTA dianhydride, and subsequently loaded with nickel ions. The Kaiser test, well-known in solid-phase peptide synthesis, was used to monitor amino silanization and the reaction with EDTA dianhydride. In addition, ICP-MS was performed to quantify the metal-binding capacity. His-tagged protein A/G (PAG), mixed with bovine serum albumin (BSA), was used as a test system. The PAG binding capacity was around 3 mg protein per gram of corundum. Cytoplasm obtained from different E. coli strains was examined as an example of a complex matrix. The imidazole concentration was varied in the loading and washing buffers. As expected, higher imidazole concentrations during loading are usually beneficial when higher purities are desired. Even when higher sample volumes, such as one liter, were used, recombinant protein down to a concentration of 1 µg/mL could be isolated selectively. Comparing the corundum material with standard Ni-NTA agarose beads indicated higher purities of proteins isolated using corundum. His6-MBP-mSA2, a fusion protein consisting of monomeric streptavidin and maltose-binding protein in the cytoplasm of E. coli, was purified successfully. To show that this method is also suitable for mammalian cell culture supernatants, purification of the SARS-CoV-2-S-RBD His8 expressed in human Expi293F cells was performed. The material cost of the nickel-loaded corundum material (without regeneration) is estimated to be less than 30 cents for 1 gram of functionalized support or 10 cents per milligram of isolated protein. Another advantage of the novel system is the corundum particles' extremely high physical and chemical stability. The new material should be applicable in small laboratories and large-scale industrial applications. In summary, we could show that this new material is an efficient, robust, and cost-effective purification platform for the purification of His-tagged proteins, even in challenging, complex matrices and large sample volumes of low product concentration.

Solidification microstructure is formed under high cooling rates and temperature gradients in powder-based additive manufacturing. In this study, a non-equilibrium multi-phase field method (MPFM), which was based on a finite interface dissipation model proposed by Steinbach et. al., coupled with a CALPHAD database was developed for a multicomponent Ni alloy. A qua-si-equilibrium MPFM was also developed for comparison. Two-dimensional equiaxed micro-structural evolution for the Ni (Bal.)–Al–Co–Cr–Mo–Ta–Ti–W–C alloy was performed at various cooling rates. The temperature–γ fraction profiles obtained under 10^5 K/s using non- and qua-si-equilibrium MPFMs were in good agreement with each other. Over 10^6 K/s, the differences between non- and quasi-equilibrium methods grew as the cooling rate increased. The non-equilibrium solidification was strengthened over a cooling rate of 10^6 K/s. Colum-nar-solidification microstructural evolution was performed under cooling rates from 5×10^5 K/s to 1×10^7 K/s at various temperature gradient values under the constant interface velocity (0.1 m/s). The results showed that as the cooling rate increased, the cell space decreased in both methods, and the non-equilibrium MPFM agreed well with experimental measurements. Our results show that the non-equilibrium MPFM can simulate solidification microstructure in powder bed fusion additive manufacturing.

Since the photocatalytic reaction is a surface reaction, enhancing the gas movement around photocatalyst would promote photocatalytic CO₂ reduction performance. A new approach to enhance the gas movement around the photocatalyst by the natural thermosiphon movement of gasses around photocatalyst using black body material was proposed and confirmed experimentally, but the heat transfer mechanism on the phenomena was not clarified yet. The purpose of this study is to clarify the heat transfer mechanism of it. This study calculated the temperature of mixed gases of CO₂ and NH₃ around P₄O₁₀/TiO₂ photocatalyst by the heat transfer formula. It is revealed that there was no difference between the increase temperature (T_g) from the temperature at the beginning of the CO₂ reduction experiment (T_ini) and the temperature of mixed gases of CO₂ and NH₃ measured by thermocouple in the experiment (T_e) under the illumination condition with a visible light (VIS) + an infrared light (IR) and IR only. The heat transfer model proposed by this study has predicted T_g well under the illumination condition with VIS + IR and IR only well. On the other hand, it is revealed that the difference between T_g and T_e was as large as 10 ℃ under the illumination condition with an ultra violet light (UV) + VIS + IR.

The present study sought to determine the effect of incorporating a Chitosan-TiO2 nano-composite on the color stability of pigmented Room Temperature Vulcanization (RTV) maxillofacial silicone subjected to a variety of accelerated aging conditions. The experimental setup consisted of one hundred groups of five disk-shaped specimens (22mm diameter, 2mm thick) each, created using RTV silicon elastomer type A-2186, with the total sample distributed into four groups based on the pigments combined with the silicon—specifically, brilliant red, blue, and yellow dry intrinsic pigments (at 0.2% concentration by weight) and a fourth group that remained non-pigmented. Each of these primary groups was further subdivided into five categories corresponding to the silicon variants treated with different nanoparticles—2% TiO2, 3% Chitosan, a hybrid nano-combination of 1% TiO2/Chitosan, 1% synthesized Chitosan-TiO2 Nanocomposite, and a control group devoid of nanoparticle additions. The synthesized Chitosan-TiO2 Nanocomposite was effectively prepared using the core-shell method. The color stability of each silicon category, irrespective of whether pigmented or non-pigmented was evaluated by calculating the color difference (ΔE) pre- and post-subjection to five distinct accelerated aging conditions: 30 hours in an antibacterial cleaning solution, six months in sebum, six months in sweat, UV-accelerated aging for 720 hours, and outdoor weathering for six months. Color measurements were taken using a Colorimeter within the CIELAB color system. Statistical analyses, including one-way ANOVA at a significance level of p < 0.05, were employed to discern significant differences among the various accelerated aging conditions across the five silicon categories. Further comparisons were made using Dennett's T3 multiple comparison test, Tukey HSD multiple comparisons, and a t-test, with SPSS for Windows version 27.0 as the software platform. Results indicated that all silicon types, whether pigmented or not, exhibited varying degrees of color change under different aging conditions. Red-colored samples, across all silicon categories, demonstrated significant color alterations after 720 hours of UV-accelerated aging, with the most pronounced change in the 3% Chitosan samples and the least in the 2% TiO2 samples. Six months of outdoor weathering led to a marked increase in ΔE values across all categories. The blue-pigmented silicon samples treated with 2% TiO2 showed the highest color modification, while the yellow-pigmented silicon and non-pigmented silicon also underwent significant color shifts, particularly in the control and Chitosan-TiO2 categories, respectively. The study underscores the pervasive influence of outdoor weathering on color stability across all silicon categories. It also demonstrates that while nanoparticle incorporation offers some resilience against accelerated aging, it fails to provide adequate protection against the specific effects of UV radiation encountered during outdoor weathering.

The bipartite entanglement is comprehensively investigated in the mononuclear molecular complex (Et3NH)[Ni(hfac)2L], where HL denotes 2-(2-hydroxy-3-methoxy-5-nitrophenyl)-4,4,5,5-tetramethyl-4,5-dihydro-1H-imidazol-3-oxide-1-oxyl and hfacH stands for hexafluoroacetylacetone. From the magnetic point of view, the molecular compound (Et3NH)[Ni(hfac)2L] consists of an exchange-coupled spin-1 Ni2+ magnetic ion and a spin-12 nitronyl-nitroxide radical substituted nitrophenol. The nickel-radical molecular complex affords an experimental realization of a mixed spin-(12, 1) Heisenberg dimer with a strong antiferromagnetic exchange coupling J/kB= 505 K and two distinct g-factors gRad=2.005 and gNi=2.275. By adopting this set of magnetic parameters we demonstrate that the Zeeman splitting of a quantum ferrimagnetic ground-state doublet due to a weak magnetic field may substantially reinforce the strength of bipartite entanglement at low temperatures. The molecular compound (Et3NH)[Ni(hfac)2L] maintains sufficiently strong thermal entanglement even at room temperature, vanishing only above 546 K. Specifically, the thermal entanglement in the nickel-radical molecular complex retains approximately 40% of the maximum value corresponding to perfectly entangled Bell states at room temperature, which implies that this magnetic compound provides suitable platform of a molecular qubit with potential implications for room-temperature quantum computation and quantum information processing.

The selective extraction of metals from aqueous solutions is very important stage in hydrometallurgical processing of metallic waste. Leach solutions are usually a multi-component mixture. The main impurity of aqueous solutions obtained after leaching using inorganic acids is iron. In this work, the membrane separation of iron(III) from nickel(II), cobalt(II) and lithium(II) was studied. The facilitated transport of metal ion using the polymer inclusion membranes (PIMs) with tetrabutylammonium bromide (TBAB) as an ion carrier under various conditions was analyzed in detail. The several factors such as the ion carrier concentration in the membrane as well as the effect of the inorganic acids concentration in the source/receiving phases on the kinetic parameters were investigated. The results show that ionic liquid TBAB is a very selective ion carrier of Fe(III) towards Ni(II), Co(II) and Li(I) .

The study aims to elaborate a neural model and algorithm for optimising hardness and porosity of coatings and thus ensure that they have superior cavitation erosion resistance. Al2O3-13wt.%TiO2 ceramic coatings were deposited onto 316L stainless steel by atmospheric plasma spray (ASP). The coatings were prepared with different values of two spray process parameters: the stand-off distance and torch velocity. Microstructure, porosity and microhardness of the coatings were examined. Cavitation erosion tests were conducted in compliance with the ASTM G32 standard. Artificial neural networks (ANN) were employed to elaborate the model, and the multi-objectives genetic algorithm (MOGA) was used to optimise both properties and cavitation erosion resistance of the coatings. Results were analysed with Matlab software by Neural Network Toolbox and Global Optimization Toolbox. The fusion of artificial intelligence methods (ANN+MOGA) is essential for future selection of thermal spray process parameters, especially for the design of ceramic coatings with specified functional properties. Selection of these parameters is a multicriteria decision problem. The proposed method made it possible to find a Pareto front, i.e. trade-offs between several conflicting objectives – maximising the hardness and cavitation erosion resistance of Al2O3-13%TiO2 coatings and, at the same time, minimizing their porosity.

One of the most important objectives of the studies worldwide is to improve the performance of automotive engines to reduce fuel consumption and environmental pollution. Accordingly, the principal motivation of this research study is improving the tribological behavior of the piston ring/cylinder liner interfaces as a promising and straightforward approach in automotive fuel economy and increasing engine durability using Al₂O₃ and TiO₂ nanomaterials as smart nano-lubricant additives that adapted to different operating conditions by replenishing mechanisms anti-friction and anti-wear in automotive engines.

Hepcidin-25 was identified as the main iron regulator in the human body by binding to the sole iron-exporter ferroportin. Studies showed that the N-terminus of hepcidin is responsible for this interaction, the same N-terminus that encompasses a small copper(II)-binding site known as ATCUN (amino terminal Cu(II)- and Ni(II)- binding) motif. Interestingly, this copper-binding property is largely ignored in most papers dealing with hepcidin-25. In this context, detailed investigations of the formed complex of hepcidin-25 with copper could reveal insights into its biological role. The present work is mainly focused on the study of the metal-bound form of hepcidin-25, which could be considered the biologically active form. The first part is devoted to the reversed-phase chromatographic separation of copper-bound and copper-free hepcidin-25, which was achieved by applying basic mobile phases containing 0.1% ammonia. Further, mass spectrometry (tandem mass spectrometry MS/MS, high resolution mass spectrometry HRMS) and nuclear magnetic resonance (NMR) spectroscopy were employed to characterize the copper-peptide. Lastly, a 3D model of hepcidin-25 with bound copper(II) is presented. The identification of metal complexes and potential isoforms and isomers, from which the latter usually are left undetected by mass spectrometry, led to the conclusion that complementary analytical methods are needed to characterize a peptide calibrant or reference material comprehensively. Quantitative nuclear magnetic resonance (qNMR), inductively-coupled plasma mass spectrometry (ICP-MS), ion-mobility spectrometry (IMS) and chiral amino acid analysis (AAA) should be considered among others.

The effect of Localized Surface Plasmon (LSP) of 5 nm mean size Au particles deposited on TiO2 P25 was investigated during the photo-thermal water gas shift reaction (WGSR). The effects of CO concentration, excitation light flux and energy, and molecular oxygen addition during the reaction were investigated. The photocatalytic WGSR rate under light excitation with wavelengths extending from 320 to 1100 nm was found to be higher than the thermal reaction alone at the same temperature (85 oC). A ratio H2/CO2 of near unity was found at high concentrations of CO. Addition of molecular oxygen during the reaction resulted in a slight decrease of molecular hydrogen production while the rates of CO2 formation and that of CO consumption changed by one order of magnitude. More important, it was found that the WGSR rates were still high under only visible light excitation (600 - 700 nm). The results prove that Au LSP alone triggers this chemical reaction without the need to excite the semiconductor on which they are deposited.

This review focuses on Cu/TiO2 sequentially and Cu-TiO2 co-sputtered catalytic/photocatalytic surfaces leading to bacterial inactivation discussing their stability, synthesis, adhesion and antibacterial kinetics. The intervention of TiO2, Cu and the synergic effect of Cu and TiO2 on films prepared by a colloidal approach and other techniques is also reviewed leading to bacterial inactivation. Processes in aerobic media and anaerobic media leading to bacterial loss of viability on multidrug resistant (MDR) pathogens, Gram-negative (-) and Gram-positive(+) bacteria are described. Insight is provided for the interfacial charge transfer mechanism under solar irradiation occurring between TiO2 and Cu. surface properties of 2D TiO2/Cu and TiO2-Cu films are correlated with the bacterial inactivation kinetics observed in the dark and under light. The intervention of these antibacterial sputtered surfaces in health-care facilities leading to MRSA-isolates is described in the dark and under the actinic light. The synergic intervention of the Cu and TiO2 films leading to bacterial inactivation prepared by direct current magnetron sputtering (DCMS), pulsed direct current magnetron sputtering (DCMSP) and highly ionized pulse plasma magnetron sputtering (HIPIMS) is reported in a detailed way.

Carbon supported nanoparticles of monometallic Ni catalyst and binary Ni-Transition Metal (Ni-TM/C) electrocatalytic composites were synthesized via chemical reduction method, where TM stands for the doping elements Fe, Co, and Cu. The chemical composition, structure and morphology of the Ni-TM/C materials were characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffractometry (XRD), transmission electron microscopy (TEM), scanning transmission electron microscopy (STEM) and energy-dispersive X-ray spectroscopy (EDS). The electrochemical properties towards hydrogen oxidation reaction in alkaline medium were studied using the rotating disc electrode and cycling voltammetry methods. A significant role of the TM dopant in the promotion of the hydrogen electrooxidation kinetics of the binary Ni-TM/C materials were revealed. A record-high in exchange current density value of 0.060 mA cm²_Ni was measured for Ni₃Fe₁/C, whereas the monometallic Ni/C counterpart has only shown 0.039 mA cm²_Ni. In order to predict the feasibility of the electrocatalysts for hydrogen chemisorption, density functional theory was applied to calculate the hydrogen binding energy and hydroxide binding energy values for bare Ni and Ni₃TM₁.

Copper(II), nickel(II) and zinc(II) complexes of various peptide fragments of tau protein were studied by potentiometric and spectroscopic techniques. All peptides contained one histidyl residue and represented the sequences of tau(91-97) (Ac-AQPHTEI-NH2), tau(385-390) (Ac-KTDHGA-NH2) and tau(404-409) (Ac-SPRHLS-NH2). Imidazole-N donors of histidine were the primary metal binding sites for all peptides and all metal ions but in case of copper(II) and nickel(II) the deprotonated amide groups were also involved in metal binding by increasing pH. The most stable complexes were formed with copper(II) ion but the presence of prolyl residues resulted in significant changes in the thermodynamic stability and speciation of the systems. It was also demonstrated that nickel(II) and especially zinc(II) complexes have relative low thermodynamic stability with these peptides. Copper(II) catalyzed oxidation of the peptides was also studied. In the presence of H2O2 the fragmentation of peptides can be detected in all cases. In the simultaneous presence of of H2O2 and ascorbic acid the extent of the fragmentation of the peptide is less preferred, and the formation of 2-oxo-histidine also occurs.

Many stable water dispersions of various chemical compositions containing bioactive chemical compounds: copper silicate, titanium dioxide and zinc oxide (and other auxiliary substances) were developed and fabricated - they were used for preparation of thin hybrid coatings having very good antimicrobial properties against gram negative bacteria (Escherichia coli), gram positive bacteria (Staphylococcus aureus) and yeast fungus (Candida albicans). Polyester (PES) nonwovens were modified by dip-coating, and PES and cotton fabrics - by dip-coating and coating methods.