We are living in a world where people always strive for the luxuries they can get with less hard work and for these smart systems are developed and established all over the world to make life easier for the people. However, in Pakistan being a third-world country we are unable to achieve better results due to the lack of proper transit from one area to another. Sometimes the roads are not in their optimum conditions and hence people have to face a lot of problems while traveling. In urban areas, people cannot reach their destination in time, in some cases, they damage their vehicles due to the cracks on the roads, in medical emergency patient dies most of the time in their transit from rescuing point to the hospital. Similarly, in rural areas where farmers face countless problems while bringing their yield of the season towards the markets. Therefore, having described the severe damage the bad quality of roads is making. A solution is proposed to solve the problems of both the rural and urban population in our project. The project aims to provide the solution to their problem to a certain extent by monitoring the conditions of the roads. The sensors in the system will calculate the values and send them to the cloud server. The cloud server used is the blynk platform where the data will be stored. Moreover, data can be provided to the government in the future for the timely maintenance of the roads, and hence the citizens and lifestyle of the people will be changed. It is expected that the problems of both urban and rural population will be solved to a greater percentage.

This paper introduces a novel respiratory detection system based on diaphragm wall motion tracking using an embedded ultrasound sensory system. We assess the utility and accuracy of this method in evaluating diaphragmatic function and its contribution to respiratory workload. The developed system is able to monitor the diaphragm wall activities when the sensor is placed in the zone of apposition (ZOA). This system allows the direct measurements with only one ultrasound PZT5 piezo transducer. The system both generates pulsed ultrasound waves at 2.2 MHz and amplifies reflected echoes. According to the diaphragmatic motions, the respiratory signals of the proposed system is insensitive to human motion artifacts. Promising results were obtained from six subjects on six different tests with an average sensitivity and specificity of 84% and 93% of respiration detection, respectively. Measurements are referenced to a SPR-BTA commercial spirometer. In this study, we also evaluated inertial and photoplethysmography (PPG) sensors as other conventional methods in this area.

Modern scientific research particularly radio astronomi- cal spectroscopic observations cannot be imagined without appropriate software suite. That is necessary because of two reasons 1) data are in digital form and 2) data processing is a complex multi-step process. In this paper created in VIRAC data processing suite for a single radio telescope, space maser observations are presented. Software Defined Radio (SDR) backend data processing is described. Implementation of the frequency switching algorithm, acquisition of observation data and their format for storing are discussed. Multiple ways to display the observation results are highlighted.

Is there a wood-feeding insect inside a tree or wooden structure? We investigate several ways on how deep learning approaches can massively scan recordings of vibrations stemming from probed trees to infer their infestation state with wood-boring insects that feed and move inside wood. The recordings come from remotely controlled devices that sample the internal soundscape of trees on a 24/7 basis and wirelessly transmit brief recordings of the registered vibrations to a cloud server. We discuss the different sources of vibrations that can be picked up from trees in urban environments and how deep learning methods can focus on those originating from borers. Our goal is to match the problem of the accelerated—due to global trade and climate change— establishment of invasive xylophagus insects by increasing the capacity of inspection agencies. We aim at introducing permanent, cost-effective, automatic monitoring of trees based on deep learning techniques, in commodity entry point as well as in wild, urban and cultivated areas in order to effect large-scale, sustainable pest-risk analysis and management of wood boring insects such as those from the Cerambycidae family (longhorn beetles).

The aim of this work is to propose two different and complementary sensors for the structural health monitoring of concrete beams. In particular, a diffused sensing element and a split ring resonator network are presented. The first sensor is able to detect the variation of the dielectric properties of the concrete along the whole beam length, for a diffuse monitoring both during the important concrete curing phase and also for the entire life cycle of the concrete beams. The resonators instead work punctually, in their surroundings, allowing an accurate evaluation of the permittivity both during the drying phase and after. This allows the continuous monitoring of any presence of water both inside the concrete beam and in points that can be critical, in the case of beams in dams, bridges or in any case subject to a strong presence of water which could lead to deterioration, or worse, cause serious accidents. Moreover, the punctual sensors are able to detect the presence of cracks in the structure and to localize them.

Currently, old-style personal medicare techniques rely mostly on traditional methods, such as cumbersome tools and complicated processes, which can be time-consuming and inconvenient in some circumstances. Furthermore, such old methods need the use of heavy equipment, blood draws, and traditional bench-top testing procedures. Invasive ways of acquiring test samples can potentially cause patients discomfort and anguish. Wearable sensors, on the other hand, may be attached to numerous body areas to capture diverse biochemical and physiological characteristics as a developing analytical tool. Physical, chemical, and biological data transferred via the skin is used to monitor health in various circumstances. Wearable sensors can assess the aberrant conditions of the physical or chemical components of the human body in real-time, exposing the body state in time, thanks to unintrusive sampling and high accuracy. Most commercially available wearable gadgets are mechanically hard components attached to bands and worn on the wrist, with form factors ultimately constrained by the size and weight of the batteries required for the power supply. Wearable gadgets with “skin-like” qualities are a new type of automation that is only starting to make its way out of research labs and into pre-commercial prototypes. In this paper, we studied the recent advancement in battery-powered wearable sensors established on optical phenomena and skin-like battery-free sensors which brings a breakthrough in wearable sensing automation.

In this paper, we introduce a non-invasive approach for monitoring bridge infrastructure with ground-based interferometric radar. This approach is called the mirror mode, since it utilises the flat surface of the bridge underside as a mirror to reflect the signal to a corner reflector on the ground placed opposite of the radar sensor. For proving the feasibility of this approach, a measurement campaign has been carried out at an exemplary bridge in Karlsruhe (Germany) including a radar sensor in mirror mode, a second radar sensor in the default mode and a laser profile scanner. We investigate the potential of this approach to monitor the bridge displacement in vertical direction and compare the results with the two other sensors. The derived results reveal the potential for monitoring bridge infrastructure. Finally, we propose further research aspects of this approach to analyse its capabilities and limitation in the context of non-invasive infrastructure monitoring.

Environmental monitoring plays a central role in diagnosing climate and management impacts on natural and agricultural systems, enhancing the understanding hydrological processes, optimizing the allocation and distribution of water resources, and assessing, forecasting and even preventing natural disasters. Nowadays, most monitoring and data collection systems are based upon a combination of ground-based measurements, manned airborne sensors or satellite observations. These data are utilized in describing both small and large scale processes, but have spatiotemporal constraints inherent to each respective collection system. Bridging the unique spatial and temporal divides that limit current monitoring platforms is key to improving our understanding of environmental systems. In this context, Unmanned Aerial Systems (UAS) have considerable potential to radically evolve environmental monitoring. UAS-mounted sensors offer an extraordinary opportunity to bridge the existing gap between field observations and traditional air- and space-borne remote sensing, by providing not just high spatial detail over relatively large areas in a cost-effective way, but as importantly providing an entirely new capacity for enhanced temporal retrieval. As well as showcasing recent advances in the field, there is also a need to identify and understand the potential limitations of UAS technology. For these platforms to reach their monitoring potential, a wide spectrum of unresolved issues and applications specific challenges require focused community attention. Indeed, to leverage the full potential of UAS-based approaches, sensing technologies, measurement protocols, post-processing techniques, retrieval algorithms and evaluations techniques need to be harmonized. The aim of this paper is to provide a comprehensive general overview of the existing research on studies and applications of UAS in environmental monitoring in order to suggest users and researchers on future research directions, applications, developments and challenges.

Background: Patients with atrial fibrillation (AF), lasting >48 h, considered for cardioversion, are recommended ≥3 weeks of oral anticoagulation before sinus rhythm restoration because of high risk of development of left atrial thrombosis (LAT) and stroke. However, the optimal duration of anticoagulation in the presence of overt LAT is unknown. Methods: An open-label study, aiming to investigate the prevalence of spontaneous echo con-trast (SEC) and LAT before and after 3 weeks of direct oral anticoagulant (DOAC) treatment. We included 51 consecutive patients (50.9% males), mean age 69.3±7.4 years with paroxys-mal/unknown duration of AF, considered for cardioversion, who agreed to have transesophage-al echocardiography at enrollment and 3 weeks later. Results: At baseline SEC was present in 26 (50.9%) and LAT in 10 (19.6%) of 51 patients. After 3 weeks on DOAC, SEC persisted in 12 (25.0%) and LAT in 7 (14.5%) of 48 patients, p<0.05 vs base-line. Factors, associated most strongly with persistence of SEC/LAT were left atrial appendage (LAA) emptying velocity <20 cm/s (OR=2.82), LAA lobes >2 (OR=1.84) and indexed left atrial volume ≥34 ml/m2 (OR=1.37). Conclusions: The recommended minimal period of 3 weeks of oral anticoagulation lead to SEC/LAT resolution in 47% of our patients. To our opinion, LA/LAA morphology and function should be taken into account when determining the duration of DOAC treatment before planned cardioversion.

Carbon capture and storage has gotten increased attention during the last decade, and several full-scale projects are currently being planned. This requires transportation of large quantities of CO2 from the capturing plant to the end point. From economic and public acceptance point of view it is important to ensure that the transportation system is operated in a safe manner. Thus, avoiding threats like corrosion or formation of particles are important. It is therefore required to monitor that the transported CO2 fulfils the required specifications, and in practice this means that the impurity content of the CO2 must be analysed. CO2 will in most cases be transported in the liquid or supercritical state (high pressure), which makes the practicalities around chemical analysis more difficult. Phase transition from liquid or supercritical state to gaseous state may also introduce several physiochemical effects that may affect the analysis. This paper discusses technical and practical challenges with such types of analysis. Most of this work is based on experience that was gained during development of analytical system for dense phase CO2 in a joint industry project that studied corrosion and chemical reactions in a simulated CO2 transport system.

Monitoring is an essential component in ecosystem management and leveraging existing data sources for multiple species of interest can be one effective way to enhance information when making management decisions. Here we analyzed juvenile Chinook Salmon (Oncorhynchus tshawytscha) bycatch data that has been collected by the recently established Enhanced Delta Smelt Monitoring program (EDSM), a survey designed to estimate the abundance and distribution of the San Francisco Estuary’s (estuary) endangered Delta Smelt (Hypomesus transpacificus). Two key aspects of the EDSM program distinguish it from other fish surveys in the estuary: a stratified random sampling design and the spatial scale of its sampling effort. We integrated the EDSM dataset with other existing surveys in the estuary and used an occupancy model to assess detection probability differences across gear types. We saw no large-scale differences in size selectivity, and while detection probability varied among gear types, cumulative detection probability for EDSM was comparable to other surveys due to the program’s use of replicate tows. Based on our occupancy model and sampling effort in the estuary during spring of 2017 and 2018, we highlighted under-sampled regions that saw improvements in monitoring coverage due to EDSM. Our analysis also revealed that each sampling method has its own benefits and constraints. Although the use of random sites with replicates as conducted by EDSM can provide more statistically robust abundance estimates relative to traditional methods, the use of fixed stations and simple methods such as beach seine may provide a more cost-effective way of monitoring salmon occurrence in certain regions of the estuary. Stronger inference on salmon abundance and distribution can be made by leveraging the strengths of each survey’s method. Careful consideration of these trade-offs is crucial as the management agencies of the estuary continue to adapt and improve their monitoring programs.

Wearable technology will become available and allow prolonged electroencephalography (EEG) monitoring in the home environment of patients with epilepsy. Neurologists analyse the EEG visually and annotate all seizures, which patients often under report. Visual analysis of a 24 hour EEG recording typically takes one to two hours. Reliable automated seizure detection algorithms will be crucial to reduce this analysis. We study a dataset of behind-the-ear EEG measurements. Our first aim was to develop a methodology to reduce the EEG dataset by classifying part of the data automatically, while retaining 100% detection sensitivity (DS). Prediction confidences are determined by temperature scaling of the classification model outputs and trust scores. A DS of approximately 90% (99%) can be achieved when automatically classifying around 90% (60%) of the data. Perfect DS can be achieved when automatically classifying 50% of the data. Our second contribution demonstrates that a common modelling strategy, where predictions from several short EEG segments are used to obtain a final prediction, can be improved by filtering out untrustworthy segments with low trust scores. The false detection rate shows a relative decrease between 21% and 43%, and the DS shows a small increase or decrease.

Monitoring is an important component of pest management, to prevent or mitigate outbreaks of native pests, and to check for quarantine organisms. Surveys often rely on trapping, especially when the target species respond to semiochemicals. Many traps are available for this purpose, but they are bulky in most cases, which raises transportation and deployment issues, and they are expensive, which limits the size and accuracy of any network. To overpass these difficulties, entomologists have used recycled material, such as modified plastic bottles, producing cheap and reliable traps but at the cost of recurrent handywork, not necessarily possible for all end-users (e.g., for national plant protection organizations). These bottle-traps have allowed very large surveys which would have been impossible with standard commercial traps, and we illustrate this approach with a few examples. Here we present, under a Creative Commons BY-SA License, the blueprint of a fan-trap, a foldable model, laser-cut from a sheet of polypropylene, that can rapidly be produced in large numbers, and could be transported and deployed in the field with very little efforts. Our first field comparisons show that fan-traps are as efficient as bottle-traps, and we describe two cases where they are being used for monitoring.

Infrared sensors are applied more and more widely in industrial production applications. Based on the theory of thermal radiation, this paper discusses the system design principle, temperature calibration method and thermal image analysis method in detail. The system has passed the measurement unit certification, showing that the field of view is 180°, the number of scanning points is 2048, the linear velocity is 10-100Hz, the spatial resolution is 2.5mrad, and the precision is ±1℃. On-line monitoring test has been done in the steelmaking plant of Bao Steel. The results show that the system has strong anti-interference ability, stability and reliability, and meets the application requirements of online monitoring.

Therapeutic Drug Monitoring (TDM) is potentially a useful tool that can be employed to increase the efficacy and decrease the toxicity of antifungal drugs. The aim of this narrative review is to provide an overview of the current use of TDM in clinical practice, and to present the evidence available regarding its use in proactive clinical settings for preventing and managing treatment failure. This review also presents the existing evidence regarding the association of various clinical outcomes with specific thresholds of drug concentrations in everyday practice. Articles concerning the use of TDM of triazoles in the treatment of fungal infections were retrieved through an electronic search using PubMed. In clinical practice, TDM has an increasingly important role in the management of antifungal drugs as a consequence of the improvement in the knowledge of the pharmacokinetics and pharmacodynamics of these drugs. The currently available evidence shows a direct exposure-response relationship for triazoles, though the PK/PD profile is unpredictable. Current guidelines and treatment consensus statements recommend the proactive TDM of voriconazole, posaconazole, and itraconazole to optimize dosage regimens and improve outcomes for adult and pediatric patients.

Condition monitoring of industrial robots has the potential to decrease downtimes in highly automated production systems. We suggest a new health indicator based on vibration data measurements and compare its performance with state-of-the-art health indicators regarding different criteria. This evaluation is based on different data sets from robot test rigs. We find that the proposed health indicator can detect different faults, has low temperature sensitivity and works in instationary velocity regimes. A discussion of the validity of the results rounds up our contribution.

Little is known about how recreational triathletes prepare for an Olympic distance event. The aim of this study was to identify the training characteristics of recreational-level triathletes within the competition period and assess how their preparation for a triathlon influences their health and their levels of fatigue. During the 6 weeks prior to an Olympic distance triathlon, and the 2 weeks after, 9 recreational athletes (5 males, 4 females) completed a daily training log. Participants answered the Daily Analysis of Life Demands Questionnaire (DALDA), the Training Distress Scale (TDS), and the Alberta Swim Fatigue and Health Questionnaire weekly. The Recovery-Stress Questionnaire (REST-Q) was completed at the beginning of the study, on the day before the competition, and at the end of week 8. Training loads were calculated using session-based rating of perceived exertion (sRPE). The data from every week of training was compared to week 1 to determine how athletes’ training and health changed throughout the study. No changes in training loads, duration, or training intensity distribution were seen in the weeks leading up to the competition. Training duration was significantly reduced in week 6 (p=0.041, d = 1.58, 95% CI = 6.9, 421.9), while the number of sessions was reduced in week 6 (Z=2.32, p=0.02, ES = 0.88) and week 7 (Z = 2.31, p=0.02, ES = 0.87). Training was characterized by large weekly variations in training loads and a high training intensity. No significant changes were seen in the DALDA, TDS, or REST-Q questionnaire scores throughout the 8 weeks. Despite large spikes in training load and a high overall training intensity, these recreational-level triathletes were able to maintain their health in the 6 weeks of training prior an Olympic distance triathlon.

TomoSim comes as part of project ATMOS, a miniaturised DOAS tomographic atmospheric evaluation device, designed to fit a small drone. During the development of the project, it became necessary to write a simulation tool for system validation. TomoSim is the answer to this problem. The software has two main goals: to mathematically validate the tomographic acquisition method; and to allow some adjustments to the system before reaching final product stages. This measurement strategy was based on a drone performing a sequential trajectory and gathering projections arranged in fan beams, before using some classical tomographic methods to reconstruct a spectral image. The team tested three different reconstruction algorithms, all of which were able to produce an image, validating the team’s initial assumptions regarding the trajectory and acquisition strategy. All algorithms were assessed on their computational performance and their ability for reconstructing spectral "images", using two phantoms, one of which custom made for this purpose. In the end, the team was also able to uncover certain limitations of the TomoSim approach that should be addressed before the final stages of the system.

Remote sensing has been used as an important tool for disaster monitoring and disaster scope extraction, especially for the analysis of temporal and spatial disasters patterns of large-scale long time series. In order to find out a rapid and effective method to monitor disaster in a wide range, based on the Google Earth Engine cloud platform, this study used MODIS vegetation index products of 250 meter spatial resolution synthesized in 16 days during the year 2005-2019 and three kinds of disaster monitoring and scope extraction models are proposed: normalized vegetation index median time standardization (RNDVI_TM(i)) model, the normalized vegetation index median phenology Standardization(RNDVI_AM(i)(j)) model, normalized vegetation index median spatiotemporal Standardization (RNDVI_ZM(i)(j)) model. The optimal threshold of disaster extraction for each model in different time phases was determined by Otsu method, and the extraction results were verified by Medium resolution image and ground measured data of the same or quasi-same period. Finally, the disaster scope of cultivated land in Heilongjiang province from 2010 to 2019 was extracted and the temporal and spatial pattern of disasters was analyzed based on the meteorological data. It shows that the three above-mentioned models have high disaster monitoring and range extraction capabilities with the verification accuracy of RNDVI_TM(i) 97.46%, RNDVI_AM(i)(j) 96.90%, and RNDVI_ZM(i)(j) 96.67% respectively. The spatial and temporal distribution of disasters is consistent with the disaster of the insured plots and meteorological data in the whole province. Meanwhile, it turns out that different monitoring and extraction methods are used in different disasters, among which wind hazard and insect disasters often need to be delayed for 16 days to observe. Each model also has various sensitivity and applicability to different disasters. Compared with other methods, this method is fast, and convenient, which allows it to be used for large-scale agricultural disaster monitoring and is easy to be applied into other research areas. The research provides a new idea for large-scale agricultural disaster monitoring.

This article discusses the results of a series of experiments on pulse ultrasonic cure monitoring of carbon fiber reinforced plastics applied to the pultrusion process. The aim of this study is to validate the hypothesis that pulse ultrasonic cure monitoring can be applied a) for profiles having small cross sections such as 7x0.5 mm and b) within the environment of the pultrusion process. Ultrasonic transducers are adhesively bonded to the pultrusion tool as actuators and sensors. The time-of-flight and the amplitude of an ultrasonic wave are analyzed to deduce the current curing state of the epoxy matrix. The experimental results show that ultrasonic cure monitoring is indeed applicable even to very thin cross sections. However, significant challenges can be reported when the techniques are used during the pultrusion process.

The present work aimed to validate a low-cost passive monitoring procedure. For its validation, the monitoring of atmospheric organic pollutants - polycyclic aromatic hydrocarbons (PAH) was carried out in a capital of the central-western region of Brazil. The sensors were fixed on poles intended for electrification during the dry season. After 15 days, samples were extracted by solvent extraction and analysed by High-Resolution Gas Chromatography with Flame Ionization Detector (HRGC-FID). For the validation of the procedure, PAHs monitored and standardised by the American Environmental Agency (EPA), a benchmark for environmental monitoring of air quality by several countries, were analysed. The results demonstrated that the low-cost passive monitoring method was effective in the quantification of PAH in the environment-air, capable of being used by countries that do not have many resources for monitoring air quality.

With an ever broadening use of composite materials manufacturers are in high demand of efficient curing cycles to reduce costs and speed up production cycles. One method to to archive this goal is active cure monitoring to determine the exact time of curing needed. This article provides a novel method to measure the cure inside of closed tools by using ultrasonic spectroscopy. For this a simple experiment is used to show the change of the ultrasonic spectrum during the cure of an epoxy. The results clearly show a direct correlation of amplitude and state of cure where the amplitude reaches a global minimum at the glass point.

The deformation of underground gateroads tends to be asymmetric and complex. Traditional instrumentation fails to accurately and conveniently monitor the full cross-sectional deformation of underground gateroads. Here, a full cross-sectional laser scanner was developed together with a visualization software package. The developed system used polar coordinate measuring method and the full cross-sectional measurement was realized by 360° rotation of laser sensor driven by an electrical motor. Later on, the potential impact of gateroad wall flatness, roughness and geometrical profile as well as coal dust environment on the performance of the developed laser scanner were evaluated. The studies show that a high-level flatness is favorable in application of the developed full cross-sectional deformation monitoring system. For a smooth surface of gateroad, the sensor cannot receive reflected light when the incidence angle of laser beam is large, causing data loss. Conversely, the roughness surface shows its priority as the diffuse reflection light can be received by the sensor. With regards to the coal dust in measurement environment, the fine particles of floating coal dust in the air can lead to the loss of measurement data to some certain due to scattering of laser beam.

Environmental monitoring is an important topic and serves a vibrant scientific role by revealing long-term trends that can lead to new knowledge and understanding. Globally, there is active development of photonic sensors incorporating multidisciplinary research. The ultimate objective is to develop small, low-cost, sensitive, selective, quick, durable, remote-controllable sensors that are resistant to electromagnetic interference. Different photonic sensor designs and advances in photonic frameworks have shown the possibility to realize these capabilities. In this review paper, the latest developments in the field of optical waveguide and fiber-based sensors which can serve for environmental monitoring are discussed. Several important topics such as toxic gas, water quality, indoor environment, and natural disaster monitoring are reviewed.

Technological innovations and the expansion of Internet access have produced significant changes in the configurations of organizations and, consequently, in the relationships between employees and employers. This new scenario generates the need for greater monitoring in the workplace in order to control inappropriate behavior or situations that may generate misfortunes. Two important problems faced are the dissemination of hate through networks and data leakage that can have social, psychological, and financial impacts. Thus, monitoring tools can be incorporated to assist in surveillance, and thus ensure the achievement of organizational objectives. This paper presents a workplace computer monitoring solution that integrates Spyware techniques, and text sentiment classification, along with a distributed microservices architecture, which aims to collect a range of information and generate alerts to managers regarding hate speech and vulnerabilities. Preliminary tests have been conducted to evaluate the performance of Spyware integrated with prediction models.

The investigation consists of taking data from the insulator chains of the 220 kV voltage for lines located in the coastal areas of Peru, in this case line 2212 from Huacho to Zapallal was chosen and the data consists of audios and images taken in hours at night when there is low temperature and high relative humidity, with the objective of identifying the characteristics that show the occurrence of effluvia that are atmospheric discharges due to the voltage of the line and the environmental conditions, this phenomenon is known as the Corona effect. Data were taken during the months of October 2020 June and July 2022, being more than 20 thousand archives of video, audio, and data (collected in csv type files), allowing to determine that the Corona effect does not manifest itself during the moments of lowest temperature. This allows redefining the maintenance strategy to be more effective in combating the damage to the insulators.

Airborne microplastic (MP) is an emerging pollutant, still under-characterised and insufficiently understood. Detailed description of MP air pollution is crucial as it has been identified in human lungs and remote locations, highlighting atmosphere as medium of MP dispersion and transportation. The lack of standardization of methods for measuring and further monitoring of the MP pollution is an obstacle towards the assessment of health risks. Since the first recognition of MP presence in the atmosphere of Krakow in 2019, this research was conducted to further characterise and develop the methods for qualitative and quantitative analysis of airborne MP (ATR-FTIR, Pyr-GC-MS, SEM-EDS) and pre-treatment of samples.The data was gathered in seven cycles, from June 2019 to February 2020. Methods used in the study allowed the identification and analysis of the changing ratio of the different types of synthetic polymers identified in the atmospheric fallout (LDPE, Nyl-66, PE, PET, PP, PUR). Observations of interactions between MP particles and environment were made with analyses of surface changes due to the degradation. Mineral phases attached to the MPs’ surfaces, with some of the inorganic contaminants transported on these surfaces, determined to also be of anthropogenic origin.Methodology proposed in this study, allows further characterisation of MP from multiple locations to provide highly comparable data, leading to the identification of the sources of this phenomenon, as well as seasonal changes.

The Open Access (OA) publishing model that is based on article processing charges (APC) is often associated with the potential for more transparency regarding the expenditures for publications. However, the extent to which transparency can be achieved depends not least on the completeness of data in APC monitoring systems. This article investigates two blind spots of the largest collection of APC payment information, OpenAPC. It aims to identify likely APC-liable publications for German universities that contribute to this system and for those that do not provide data to it. The calculation combines data from Web of Science, the ISSN-Gold-OA-list and OpenAPC. The results show that for the group of universities contributing to the monitoring system, more than half of the APC payments are not covered by it and the average payments for non-covered APCs is higher than for APCs covered by the system. In addition, the group of universities that does not contribute to OpenAPC accounts for two thirds of the number of APC-liable publications recorded for contributing universities. Regarding the size of these blind spots, the value of the monitoring system is limited at present.

This paper addresses a wildlife monitoring problem using a team of UAVs for efficient monitoring of wildlife. The state-of-the-art technology using UAVs has been an increasingly popular tool to monitor wildlife compared to the traditional methods such as satellite imagery-based sensing or GPS trackers. However, there still exist unsolved problems as to how the UAVs need to cover a spacious domain to detect animals as many as possible. In this paper, we propose the optimal transport-based wildlife monitoring strategy for a multi-UAV system, to prioritize monitoring areas while incorporating complementary information such as GPS trackers and satellite-based sensing. Through the proposed scheme, the UAVs can explore the large-size domain effectively and collaboratively with a given priority. The time-varying nature of wildlife due to their movements is modeled as a stochastic process, which is included in the proposed work to reflect the spatio-temporal evolution of their position estimation. In this way, the proposed monitoring plan can lead to efficient wildlife monitoring with a high detection rate. Various simulation results including statistical data are provided to validate the proposed work.

Accurately mapping individual tree species in densely forested environments is crucial to forest inventory. When considering only RGB images, this is a challenging task for many automatic photogrammetry processes. The main reason for that is the spectral similarity between species in RGB scenes, which can be a hindrance for most automatic methods. State-of-the-art deep learning methods could be capable of identifying tree species with an attractive cost, accuracy, and computational load in RGB images. This paper presents a deep learning-based approach to detect an important multi-use species of palm trees (Mauritia flexuosa; i.e., Buriti) on aerial RGB imagery. In South-America, this palm tree is essential for many indigenous and local communities because of its characteristics. The species is also a valuable indicator of water resources, which comes as a benefit for mapping its location. The method is based on a Convolutional Neural Network (CNN) to identify and geolocate singular tree species in a high-complexity forest environment, and considers the likelihood of every pixel in the image to be recognized as a possible tree by implementing a confidence map feature extraction. This study compares the performance of the proposed method against state-of-the-art object detection networks. For this, images from a dataset composed of 1,394 airborne scenes, where 5,334 palm-trees were manually labeled, were used. The results returned a mean absolute error (MAE) of 0.75 trees and an F1-measure of 86.9%. These results are better than both Faster R-CNN and RetinaNet considering equal experiment conditions. The proposed network provided fast solutions to detect the palm trees, with a delivered image detection of 0.073 seconds and a standard deviation of 0.002 using the GPU. In conclusion, the method presented is efficient to deal with a high-density forest scenario and can accurately map the location of single species like the M flexuosa palm tree and may be useful for future frameworks.

Background and Objectives: The IPED study showed that a smartphone-based event recorder increased the number of patients in whom an ECG was captured during symptoms over five-fold to more than 55% at 90 days compared to standard care [1] and concluded that this safe, non-invasive and easy to use device should be considered part of on-going care to all patients presenting acutely with unexplained palpitations or pre-syncope. This study reports the process of establishing a smartphone palpitation and pre-syncope service. Materials and Methods: A clinical Standard Operating Procedure (SOP) was devised, and funding was secured through a business case for the purchase of 40 AliveCor devices in the first instance. The clinic was launched on 22nd July 2019. Results: Between 22nd July 2019 and 31st October 2019, 68 patients seen in the ED with palpitations or pre-syncope were referred to SPACC. 30 were male and 38 female and mean age was 45.8 (SD 15.1) with a range from 18 to 80 years. 50 (74%) patients underwent full investigation. 7 (11%) patients were deemed on first assessment to have non-cardiac palpitations and were not fitted with the device. All patients who underwent full investigation achieved symptomatic rhythm correlation most with sinus rhythm, ventricular ectopics or bigeminy. A symptomatic cardiac dysrhythmia was detected in 6 (8.8%) patients. 3 patients had supraventricular tachycardia; SVT (4%), 2 had atrial fibrillation (3%) and 1 atrial flutter (2%). Qualitative feedback from the SPACC team suggested several areas where improvement to the clinic could be made. Conclusion: We believe a smartphone palpitation service based in ambulatory care is simple to implement and is effective at detecting cardiac dysrhythmia in ED palpitation patients.

(1) Background: Show caves are unique natural attractions and touristic traffic can trigger their degradation within a very short time. There are no universal solutions to counter the effects of the touristic impact upon cave environment and both protection protocols and management plans have to be established on a case-by-case basis; (2) Methods: The study includes four show caves from the Romanian Carpathians, where monitoring of the number of visitors, paralleled by the monitoring of the main physico-chemical parameters of the air and water (CO2, temperature, humidity, drip rate, conductivity, and pH) was implemented; (3) Results and Conclusions: The results of the study has: (i) established a monitoring protocol to be applied to each of the four show caves; (ii) established a set of basic principles to be enforced by the management of show caves; (iii) issued a set of preventive measures and instructions to be followed by the personnel and stakeholders of the caves.

Coral reefs are declining worldwide due to global changes in the marine environment. The increasing frequency of massive bleaching events in the tropics is highlighting the need to better understand the stages of coral physiological responses to extreme conditions. Moreover, like many other coastal regions, coral reef ecosystems are facing additional localized anthropogenic issues such as nutrient loading, increased turbidity, and coastal development. Different strategies have been developed to measure the health status of a damaged reef, ranging from the resolution of individual polyps to an entire coral community, but techniques for measuring coral physiology in situ are not yet widely implemented. For instance, while there are many studies of the coral holobiont response in single or limited-number multiple stressor experiments, they provide only partial insights to metabolic performance under more complex temporally and spatially variable natural conditions. Here, we discuss the current status of coral reefs and their global and local stressors in the context of experimental techniques that measure core processes in coral metabolism (respiration, photosynthesis, and biocalcification) in situ, and their role in indicating the health status of colonies and communities. We highlight the need to improve the capability of in situ studies in order to better understand the resilience and stress response of corals under multiple global and local scale stressors.

Condition monitoring of bearings is an open issue. The use of the stator current to monitor induction motors has been validated as a very advantageous and practical way to detect several types of faults. Nevertheless, for bearing faults the use of vibrations or sound generally offers better results in the accuracy of the detection although with some disadvantages related to the sensors used for monitoring. To improve the performance of bearing monitoring, it is proposed to take advantage of more information available in the current spectra, beyond the usually employed, incorporating the amplitude of a significant number of sidebands around the first eleven harmonics, growing exponentially the number of fault signatures. This is especially interesting for inverter-fed motors. But, in turn, this leads to the problem of overfitting when applying a classifier to perform the fault diagnosis. To overcome this problem, and still exploit all the useful information available in the spectra, it is proposed to use shrinkage methods, which have been lately proposed in machine learning to solve the overfitting issue when the problem has much more variables than examples to classify. A case study with a motor is shown to prove the validity of the proposal

Operational weather and also flood forecasting has been performed successfully for decades and is of great socioeconomic importance. Up to now, forecast products focus on atmospheric variables, such as precipitation, air temperature and, in hydrology, on river discharge. Considering the full terrestrial system from groundwater across the land surface into the atmosphere, a number of important hydrologic variables are missing especially with regard to the shallow and deeper subsurface (e.g. groundwater), which are gaining considerable attention in the context of global change. In this study, we propose a terrestrial monitoring/forecasting system using the Terrestrial Systems Modeling Platform (TSMP) that predicts all essential states and fluxes of the terrestrial hydrologic and energy cycles from groundwater into the atmosphere. Closure of the terrestrial cycles provides a physically consistent picture of the terrestrial system in TSMP. TSMP has been implemented over a regional domain over North Rhine-Westphalia and a continental domain over European in a real-time forecast/monitoring workflow. Applying a real-time forecasting/monitoring workflow over both domains, experimental forecasts are being produced with different lead times since the beginning of 2016. Real-time forecast/monitoring products encompass all compartments of the terrestrial system including additional hydrologic variables, such as plant available soil water, groundwater table depth, and groundwater recharge and storage.

GNSS receivers are nowadays commonly used in monitoring applications, e.g., in estimating crustal and infrastructure deformations. This is basically due to the recent improvements in GNSS instruments and methodologies that allow high precision positioning, 24 h availability and semiautomatic data processing. In this paper, GNSS estimated deformations on a dam structure have been analyzed and compared with pendulum data. This study has been carried out for the Eleonora D’Arborea (Cantoniera) dam, which is in the Sardinia Island. Time series of pendulum and GNSS over a time span of 2.5 years have been aligned so to be comparable. Analytical models fitting these time series have been estimated and compared. Those models were able to properly fit pendulum data and GNSS data, with standard deviation of residuals smaller than one millimeter. This encouraging results led to the conclusion that GNSS technique can be profitably applied to dam monitoring allowing a denser description, both in space and time, of the dam displacements than the one based on pendulum observations.

Recent researches proved that the underbridge geometry can be reconstructed by mounting a 3D laser scanner on a motorized cart travelling on a walkway located under the bridge. The walkway is moved by a truck and the accuracy of the bridge model depends on the accuracy of the trajectory of the scanning head with respect to a fixed reference system. In this paper, we describe the metrological characterization of a method that uses non-contact systems to identify the relative motion of the cart with respect to the walkway; the orientation of the walkway with respect to the bridge is determined using inclinometers and optical rails, while the position of the truck with respect to the bridge is measured using a conventional odometer. The measurement uncertainty of the proposed system was initially evaluated by numerical simulations and successively verified by experiments in laboratory conditions. The complete system has then been tested in operative conditions; the validity of the proposed approach has been demonstrated by comparing the geometry of buildings reconstructed with the proposed system with the geometry obtained with a static scan. Results evidenced that the errors are approximately 6 mm.

Monitoring complex electro-mechanical processes is not straightforward despite the arsenal of techniques nowadays availanle. This paper presents a method based on Adaptive-Network-based Fuzzy Inference System (ANFIS) to estimate eccentricity of its spinning axis. The method is experimentally tested on an ultra-precision rotating device commonly used for micro-scale turning. The developed model has three inputs, two obtained from a frequency domain analysis of a vibration signal and the third, which is the device rotation frequency. A comparative study demonstrates that an adaptive neural-fuzzy inference system model provides better error-based performance indices for detecting imbalance than a non-linear regression model. This simple, fast, and non-intrusive imbalance detection strategy is proposed to counteract eventual deterioration in the performance of ultra-high precision rotating machines due to vibrations.

The switch from intermittently scanned continuous glucose monitoring (isCGM) to real-time (rt) CGM could improve glycemic management in suboptimal controlled type 1 diabetes patients, but long-term study is lacking. We evaluated retrospectively the ambulatory glucose profile (AGP) in such patients after switching from Free Style libre 1 (FSL1) to Dexcom G4 (DG4) over 1 year. Patients (n=21, 43±15 years, BMI 25±5, HbA1c 8.1±1.0%) had severe hypoglycemia and/or HbA1c≥8%. AGP metrics (time-in-range (TIR) 70-180 mg/dL, time-below-range (TBR)<70 mg/dL or <54 mg/dL, glucose coefficient of variation (%CV), time-above-range (TAR) >180 mg/dL or >250 mg/dL, glucose management indicator (GMI), average glucose) were collected the last 3 months of FSL1 use (M0) and of DG4 for 3, 6 (M6) and 12 (M12) months of use. Values were means ± standard deviation or medians [Q1;Q3]. At M12 versus M0, the higher TIR (50±17 vs. 45±16, P=0.036), and lower TBR<70 mg/dL (2.5 [1.6;5.5] vs. 7.0 [4.5;12.5], P=0.0007), TBR<54 mg/dL (0.7 [0.4;0.8] vs. 2.3 [0.8;7.0], P=0.007) and %CV (39±5 vs. 45±8, P=0.0009), evidenced a long-term effectiveness of the switch. Compared to M6, TBR<70mg/dL decreased, %CV remained stable, while the improvement on hyperglycemia exposure decreased (higher GMI, TAR and average glucose). This switch was a relevant therapeutic option, though a loss of benefit on hyperglycemia stressed the need for optimized management of threshold alarms. Nevertheless, few patients attained the recommended values for AGP metrics, and the reasons why some patients are “responders” vs “non-responders” warrant to be investigated.

This work describes a new transducer prototype for continuous monitoring both in the structural and geotechnical fields. The transducer is synthetically constituted by a wire of optical fiber embedded between two fiber tapes (fiberglass or carbon fiber) and glued by a matrix of polyester resin. The fiber optical wire ends have been connected to a control unit whose detection system is based on Brillouin optical time-domain frequency analysis. Three laboratory tests were carried out to evaluate the sensor's reliability and accuracy. In each experiment, the transducer was applied to a sample of inclinometer casing sets in different configurations and with different constraint conditions. The experimental data collected were compared with theoretical models and with data obtained from the use of different measuring instruments to perform validation and calibration of the transducer at the same time. Several diagrams allow comparing the transducer and highlighting its suitability for monitoring and maintenance of structures. The characteristic of the transducer suggests its use as a mixed system for reinforcing and monitoring, especially in lifetime maintenance of critical infrastructures such as transportation and service networks, and historical heritage.

Plankton monitoring by microscopy offers long-term ecological perspective of plankton com-munities but different detection approaches are biased uniquely. Genetic identification of marine plankton has become standard but is still not used in routine monitoring. This study assessed the diversity of plankton taxa using 18S high throughput sequencing from 2011-2012 from small-volume (~200ml) samples from the Water and Microplankton Sampler (WaMS) deployed on the Continuous Plankton Recorder platform (CPR). The 18S-HTS survey revealed a bias towards heterotrophic taxa, and phototrophs under 10µm within the photosynthetic community. In comparison with phytoplankton microscopic counts from the CPR survey and Western Channel Observatory station L4, only 8-12 taxonomic families were common to all three surveys, with a bias towards larger diatoms and dinoflagellate taxa in microscopy surveys. The WaMS survey detected a contrasting but complementary taxa set to that of microscopic surveys. Additional Quantitative PCR was carried out on the picoeukaryotic pelagophyte, Aureococcus anophagefferens, and the nanoeukaryotic potential harmful algae, Pseudo-nitzschia delicatissima, from 2011-2013. This confirmed the persistence presence of A. anophagefferens in the Western Channel and an elevated abundance of both species in 2011. Species specific seasonality were distinct from those of aggregrate phytoplankton groups.

Background/Objectives: The purpose of the proposed study is disclosure of correlations between the dynamics of the Breathe Rate (BR) and Heart Rate (HR) when performing the intermittent physical operation at maximum power on a cycle ergometer.Methods: The stage on the study of the General functional athlete readiness (GFAR) performed using the sports standard “Red Engine” and the cycle ergometer in 16 volunteers (10 men, 6 women) whose average age was 21±1.17 years. To determine the sports potential of the volunteers in this study, we used own Coefficient of Anaerobic Capacity (CANAC Q, beats). Continuous recording of the heart rate and respiratory rate of volunteers in the maximum power sports test was carried out by the “RheoCardioMonitor” device with an athlete functional readiness module based on the method of Transthoracic electrical impedance rheography (TEIRG).Results: The degree of correlation of functional indicators (M, HR_M, GFAR) with CANAC Q for the group in full (n=80) occurred at a very high level, which confirmed the effectiveness of using the Coefficient of Anaerobic Capacity (CANAC Q) in assessing the general functional athlete readiness of the volunteers. Conclusions: CANAC Q measured in “beats” of the heart and recorded very accurately using the method of transthoracic electrical impedance rheography (TEIRG). For this reason as promising sports PSM-system, CANAC Q can replace the methods for determining the functional athlete readiness by blood lactate concentration and maximum oxygen consumption.

Drought is considered one of the severest natural disasters and it is difficult to predict it. This review article aimed to display the state of the art of methods used to predict and monitor types of droughts. We examine more than 30 indices and models to identify the strengths and weaknesses of methods and identify gaps remaining in this field. Examples of examined indies are Palmer Drought Severity Index (PDSI), Standardized Precipitation Index (SPI), and Standardized Precipitation Evapotranspiration Index (SPEI). The research found improvement in drought modeling, however, more focus and improvement are required to monitor and predict drought types. It also found that some methods outperform others such as PDSI, SPI, SPEI, EVI, NDVI, NDWI, VCI and TCI.

Plankton monitoring by microscopy offers long-term ecological perspective of plankton communities but is biased towards those organisms that can be distinguished using the microscope. Genetic identification of marine plankton has become standard but is still not used. This study is a comprehensive study genetically measured taxa in the Western Channel of UK using a small-volume automated water sampler deployed on the CPR platform. The study present one year of high-throughput sequencing data focussing on smaller plankton and separate community to that measured by microscopy that can complement each other for a holistic view of plankton. Quantitative tests of two harmful algae show relatively high abundance of the Pelagophyte Aureococcus anophagefferens during 2011 with low nitrite levels. Three years of Pseudo-nitzschia delicatissima quantitative monitoring also shows a greater abundance of this potentially harmful taxa in 2011. Flow cytometry reveals distinct seasonal cycles with distinct timings.

Abstract: Background: Stunting is primarily a public health concern in LMIC. The involvement of Integrated Service Post cadres is one of the strategies to combat stunting in Indonesia. Objective: This study aimed to determine the effect of a short course on cadres knowledge. Method: A single group pre-post test design was conducted in Yogyakarta, Indonesia, from March to May 2022. Thirty cadres were selected based on the following criteria: willingness to participate, the number of stunted children in their Integrated Service Post (Posyandu), and full attendance at short course. The knowledge scores were measured by a structured questionnaire after short course (post-test 1) and 4 weeks later (post-test 2). We apply STATA 16 to calculate the mean difference (MD) using a t-test and Generalized Estimated Equation (GEE). Furthermore, the adequacy of the short course was evaluated with in-depth interviews. Result: On post-tests 1 and 2, cadres' knowledge of IYCF, children growth monitoring (CGM) and children development monitoring (CDM) significantly improved. The GEE analysis showed that a short course significantly improves cadres' knowledge after age control, education, occupation, and years of experience. Conclusion: Short course in-creased their affection, self-efficacy, and confidence, hence, they are capable of assisting children through home visits.

Accurately monitoring insecticide resistance in target mosquito populations is important to combating malaria and other vector-borne diseases, and robust methods are key. The “WHO susceptibility bioassay” has been used for +60 years: mosquitoes of known physiological status are exposed to a discriminating concentration of insecticide. Several changes to the test procedures have been made historically which may seem minor but could impact bioassay results. The published test procedures and literature for this method were reviewed for methodological details. Areas where there was room for interpretation in the test procedures or where the test procedures were not being followed were assessed experimentally for impact on bioassay results: covering or uncovering of the tube end during exposure, number of mosquitoes per test unit, and mosquito age. Many publications do not cite the most recent test procedures, methodological details are reported which contradict the test procedures referenced or methodological details are not fully reported. As a result, the precise methodology is unclear. Experimental testing showed that using fewer than the recommended 15-30 mosquitoes per test unit significantly reduced mortality, covering the exposure tube had no effect, and using mosquitoes older than 2-5 days old increased mortality, particularly in the resistant strain. Recommendations are made for better reporting of experimental parameters.

Abstract: The Hanqu Joint Station of the Dingbian Oil Production Plant of Yanchang Oilfield Co., Ltd is located at the edge of the desert in northern China. the bad field conditions and strong sandstorm, the hardware of computer monitoring system of Joint Station is often damaged. At the same time, the core equipment of the joint station three-phase separator oil chamber liquid level is hard to achieve high precision constant value control, the general control algorithm is difficult to meet the control requirements.This paper proposed a design scheme of a oilfield joint station computer monitoring system based on the Siemens S7-300 PLC, the hardware of the monitoring system adopts the redundancy scheme of dual monitoring computers, dual programmable logic controllers (PLCs), and dual industrial Ethernet. The BP neural network PID control algorithm was used to realize constant value control of the oil chamber liquid level of the three-phase separator of the core equipment of the joint station，and realized high control precision. The monitoring system could well adapt to the harsh environment of the scene, and showed high reliability and efficiency.

As the number of legal and illegal mining sites increase, integrative methods to evaluate the effects of mining pollution on Andes-Amazonia freshwater ecosystems are paramount. Here, we sampled water and sediments in 11 sites potentially affected by mining activities in the Napo province (Ecuador). The environmental impacts were evaluated using four lines of evidence (LOEs): water physico-chemical parameters; metal exposure concentrations; macroinvertebrate community response (AAMBI); and toxicity by conducting bioassays with Lactuca sativa and Daphnia magna. Overall, dissolved oxygen and total suspended solids were, under (&lt;80%) and above (&gt;130 mg/Ls) quality standards. Ag, Al, As, Cd, Cu, Fe, Mn, Pb and Zn in water and V, B and Cr in sediments were detected above quality standards. Nine out of eleven sites were classified as having bad environmental quality based on the AAMBI. Ranges of L. sativa seed germination in both water (37% to 70%) and sediment (0% to 65%), indicate significant toxicity. In 5 sites, neonates of D. magna showed a 25% reduction in survival compared to the control. Our integrated LOEs index ranked sites regarding their environmental degradation. Given the importance of the Andes-Amazon region, we recommend environmental impact monitoring of the mining expansion using multiple LOEs.

There are numerous challenges involved in the diagnosis and treatment of lung cancer. Globally, majority of people suffers from cancerous disease involving throat cancer, lung cancer, stomach cancer, cancerous brain tumor. Among these the most common ones is the lung cancer or lung carcinoma. The leading cause of the lung cancer is the smoking. Around 80% to 90% of deaths are caused due to Non-small cell lung cancer (NSCLC). The inadequate diagnostic techniques and low chances for the survival of lung cancer patients results from the lack of an early prognosis and incompetency in traditional therapies. However, such challenges involved in the prognosis and treatment of lung cancer are on decline with the progression in magnetic nanoparticle (MNP) technology. Many break-through discoveries and inventions have been made in the field of cancer therapy by using magnetic nanoparticles. The implication of nanotechnology has led to the recent advancement in nanomedicine field. This has encouraged the improvement in different therapeutic and diagnosis strategies employing nanotechnology. The generation of immense technological benefits for nanoparticles systems has been accredited to its remarkable nanoscale physico-chemical properties. This in turns provides the early detection of lung cancer and active drugs delivery for an improved theranostics strategy. The present review provides a general idea of the current progression in the therapeutic and prognosis purpose of magnetic nanoparticles. Further, we disclose the development in the lung cancer theranostics by functionalization of magnetic nanoparticles. The established importance of magnetic nanoparticles in the theranostics centers for lung cancer has been revealed in this paper. The challenges existing in the theranostics of lung cancer are addressed through the functioning of magnetic nanoparticles in the process.

Pathogens and adulterants in human feeding consumables can be readily identified according to their electrical properties. Electrical bioimpedance analysis (BIA) has been widely used for body contents characterization, such as blood, urine, lactate and sweat. If the blood glucose concentration alters the electrical properties of the blood medium, then the impedance spectrum obtained by BIA can be used to measure glycemia. In some applications, artificial neural networks allows the correlation of these parameters (impedance and glucose concentration) by means of symbolic and statistical rules. According to our literature review, there is any physical model that allows the interpretation of the relationship between blood’s electrical properties, obtained by BIA, and the concentration of glucose in the blood plasma. This article proposes a simplified physical model for blood electrical conductivity as a function of glucose concentration, based on Bruggeman’s effective medium theory. The equations of this model were obtained considering an insulating phase distribution diffused in a conductive matrix, in which red blood cells are represented by macroscopic insulating nuclei and glucose molecules by microscopic insulating particles. The impedance spectrum for different glucose concentrations (4.0 to 6.8 mmol/L) in a blood sample, published by Kamat Bagul (2014), were compared with the proposed model. The results showed a significant correlation with the experimental data, showing a maximum error of 5.2%. The proposed model might be useful in the design of noninvasive blood glucose monitoring systems.

Objectives: To investigate the value of early lactate dynamic monitoring index in predicting prognosis of patients with sepsis and septic shock. Methods: We performed our test on 50 patients. Out of 50 patients, 28 are male, and 22 are female. Prospectively studied pediatric patients with septic shock were performed. Vital signs, Lactate clearance, were obtained at presentation 6 h, 12 h, 24 h over the first 48 h of hospitalization. The therapy received, outcome parameters of mortality and duration of hospitalization were recorded. Results: The statistical data and comparative analysis showed that an average of 16.88 days after admission, 5 patients have died, 17 patients are poorly prognosis leaves the hospital, and the remaining 28 are recovered and discharged. The primary outcome variable of mean 16 days hospitalization mortality rate was 10%. Poor prognosis 34% and fully recovery 56 % were observed. In this retrospective cohort study, a lactate level of more than 2.5mmol/L was the best threshold to predict 28-day mortality among severe sepsis and septic shock patients. In our research, we found mean LC 6 h 3.08mmol/L, and after 48 h mean it is 1.79mmol/L. Significant LC 6 h found, which is 8.08mmol/L in the death group patient where 48 h mmol/L shows significant high. Poor prognosis also presents a clinical increase of lactate level high in the LC 6 h analysis, which is 3.32mmol/L. Recovered patients showed a significant improvement after administering treatment depending on the patient organ involvement and good decrease of lactate reports achieved, which is 1.20mmol/L, where admission reports show it was 1.91mmol/L in LC 6 h. Mean Heart rate 94/51mmhg, pulse 119, temperature 39℃, respiratory rate 32.26, and urine output 456 ml recorded during our study. Death patient shows a remarkable detonation of those reports but has a significant clinical report with the recovered patients. Conclusion: The early lactate dynamic monitoring index has a high value in predicting sepsis and septic shock patients' prognosis, thus worth popularizing.

The green biomass of horticultural plants contains valuable secondary metabolites (SM) which can potentially be extracted and sold. When exposed to stress, plants accumulate higher amounts of these SMs, making the extraction and commercialization even more attractive. We evaluated the potential for accumulating of the flavones cynaroside and graveobioside A in leaves of two bell pepper cultivars (Mavras and Stayer) when exposed to salt stress (100 mM NaCl), UVA/B excitation (UVA 4-5 W/m²; UVB 10-14 W/m² for 3 hours per day) or a combination of both stressors. HPLC analyses proved the enhanced accumulation of both metabolites under stress conditions. Cynaroside accumulation is effectively triggered by high-UV stress, whereas graveobioside A contents increase under salt stress. Highest contents were observed in plants exposed to combined stress. Effects of stress on overall plant performance differed significantly between treatments, with least negative impact on aboveground biomass found for high-UV stressed plants. The usage of two non-destructive instruments (Dualex and Multiplex) allowed us to gain insights in ontogenetical effects at the leaf level and temporal development of SM contents over time. Indices provided by those devices correlate fairly with amounts detected via HPLC (Cynaroside: R2 = 0.46 – 0.66; Graveobioside A: R2 = 0.51 – 0.71). The concentrations of both metabolites tend to decrease at leaf level during the ontogenetical development even under stress conditions. High-UV stress is a promising tool for enriching plant leaves with valuable SM without major effects on plant biomass. All data is available online [1].

The paper presents a case study and a model for condition monitoring of Diesel engines’ oil of urban buses, through the accompaniment of the evolution of its degradation, with the objective to implement a predictive maintenance policy. Along time, because the usage, there is some decay in the lubricant properties. However, in normal functioning conditions, the lubricants properties, at the time the manufacturers recommend its changing, regardless of they are within the safety limits. Then, based on the accompaniment of the lubricants’ oil condition, the intervals of oil replacement can be enlarged what implies the availability increasing and the corresponding production increasing of the equipment. The model presented in this paper shows its potential to be spread to other types of equipment and organisations that want can implement similar maintenance policies, to achieve the best availability based on the real equipment health conditioning conditions

Multi-view stereo (MVS) employs multi-point photography for image point positioning and three-dimensional reconstruction technology. Recently, this technology has been introduced into the monitoring of road slopes due to advances in photography and computing technology. In general, the various phases of post-image processing procedures are applied to various photographic data. In this study a novel, automated image-monitoring system is proposed to improve the ability of automatic processing. First, an Internet of things (IoT)-based digital photography system architecture was constructed to provide automatic control of camera photography and real-time transmission of image data. In addition, a visual SfM-MVS 3D reconstruction technique was used to develop related software and hardware interfaces based on the built-in Python computing framework of Photoscan Pro. The software integrates fully automatic photography, image transmission, monitoring of data processing and product release programs. The experimental results show that the system architecture can be applied to fully automatic three-dimensional monitoring of road slopes.

This paper focuses on optimal sensor positioning for monitoring activities of daily living and investigates different combinations of features and models on different sensor positions, i.e., the side of the waist, front of the waist, chest, thigh, head, upper arm, wrist, and ankle. Sixteen features are extracted and the feature importance is measured by using the Relief-F feature selection algorithm. Eight classification algorithms are evaluated on a dataset collected from young subjects and that collected from elderly subjects, with two different experimental settings. To deal with different sampling rates, signals with a high data rate are down-sampled and a transformation matrix is used for aligning signals to the same coordinate system. The thigh, chest, side of the waist, and front of the waist are the best four sensor positions for the first dataset (young subjects), with average accuracy values being greater than 95%. The best model obtained from the first dataset for the side of the waist is validated on the second dataset (elderly subjects). The most appropriate number of features for each sensor position is reported. The results provide a reference for building activity recognition models for different sensor positions, as well as for data acquired from different hardware platforms and subject groups.

This paper present a platform for airborne sensor applications using low-cost, open-source components carried by an easy-to-fly unmanned aircraft vehicle (UAV). The system, available in open-source [1], is designed for researchers, students and makers for a broad range of their exploration and data-collection needs. The main contribution is the extensible architecture for modularized airborne sensor deployment and real-time data visualisation. Our open-source Android application provides data collection, flight path definition and map tools. Total cost of the system is below 800 dollars. The flexibility of the system are illustrated by mapping the location of Bluetooth beacons (iBeacons) on a ground field and by measuring water temperatures in a lake.

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

We present a custom platform that integrates data from several sensors measuring synchronously different variables of the beehive and wirelessly transmits all measurements to a cloud server. There is a rich literature on beehive monitoring. The choice of our work is not to use ready platforms such as Arduino and Raspberry Pi and to present a low cost and power solution for long term monitoring. We integrate sensors that are not limited to the typical toolbox of beehive monitoring such as gas, vibrations and bee counters. The synchronous sampling of all sensors every 5 minutes allows us to form a multivariable timeseries that serves two-ways: a) it provides immediate alerting in case a measurement exceeds predefined boundaries that are known to characterize a healthy beehive, and b) based on historical data predict future levels that are correlated with hive’s health. Finally, we demonstrate the benefit of using additional regressors in the prediction of the variables of interest. The database, the code and a video of the vibrational activity of two months are made open to the interested readers.

In the current research work, electrical resistance tomography (ERT) was employed for crystallization process monitoring and visualization. A first-of-its-kind MATLAB-based interactive GUI application “ERT-Vis” is presented. Two case studies involving varied crystallization methods were undertaken. The experiments involving calcium carbonate reactive (precipitative) crystallization for the high conductivity solution-solute media and the cooling crystallization for sucrose crystallization representing the lower conductivity solution-solute combination were designed and performed. The software successfully provided key insights regarding the process progress in both crystallization systems. It could detect and separate the crystal agglomerations in the low as well as high conductivity solutions using visual analytics tools provided. The performance and utility of the software were studied using a software evaluation case study involving domain experts. Participant feedback indicated that ERT-Vis software helps in reconstructing images instantaneously, interactively visualizing, and evaluating the output of the crystallization process monitoring data.

The global financial crisis of 2008, triggered by the collapse of Lehman Brothers, highlighted a banking system that was widely exposed to systemic risk. The minimization of the systemic risk via a close and detailed monitoring of the entire banking network became a priority. This is a complex and demanding task considering the size of the banking systems: in the US and the EU they include more than 10000 institutions. In this paper, we introduce a methodology which identifies a subset of banks that can: a) efficiently represent the behavior of the whole banking system and b) provide, in the case of a failure, a plausible range of the crisis dispersion. The proposed methodology can be used by the regulators as an auxiliary monitoring tool, to identify groups of banks that are potentially in distress and try to swiftly remedy their problems and minimize the propagation of the crisis by restricting contagion. This methodology is based on Graph Theory and more specifically Complex Networks. We termed this setting a “multivariate Threshold – Minimum Dominating Set” (mT–MDS) and it is an extension of the Threshold – Minimum Dominating Set methodology (Gogas e.a., 2016). The method was tested on a dataset of 570 U.S. banks: 429 solvent and 141 failed ones. The variables used to create the networks are: the total interest expense, the total interest income, the tier 1 (core) risk-based capital and the total assets. The empirical results reveal that the proposed methodology can be successfully employed as an auxiliary tool for the efficient supervision of a large banking network.

Abstract: In the last five years, the urban development of Limassol City has rapidly increased in the sectors of industry, trade, real estate, and many others. This exponentially increased urban development introduces several concerns about the aggravation of the land subsidence in the Limassol coastal front. Fifty Copernicus Sentinel-1 data from 2017-2021 have been processed and analyzed using the Sentinel Application Platform (SNAP) and the Stanford Method for Persistent Scatters (StaMPS). A case study for the identification and analysis of the elements (PS) in pixels in a series of interferograms, and then, the quantity of the land displacements in the Line of Sight, in the Limassol coastal front, is presented in this research, with the subsidence rates up to about (-5 to 4 mm / year). For the validation of the detected deformation, accurate ground-based geodetic measurements along the coastal area were used. Concordantly, taking into account that there are a significant number of skyscrapers planned to be built, this study attempts a preliminary assessment of the impact these structures will pose on the coastal front of the area of Limassol.

In the present work, cost-effective strain gauges were fabricated by using inkjet printing and photonic curing on flexible and recyclable PET substrates. Ohmic resistance (a.k.a. DC resistance) (R0) and complex electrical impedance (Z) as a function of test frequency were characterized, respectively, with the state-of-the-art electronic testing equipments. For the fabrication process, commercially available silver nanoparticle (AgNP) inks and printing substrates were used in order to eliminate any apriori ink processing. In order to validate the in-house cantilever beam measurement setup and devices, first, commercially available metallic foil strain gauges (with the provided gauge factor GF=2 by the manufacturer) were tested at different locations. Thereafter, the printed strain gauges were investigated with several repetitions at different measurement locations. The measurement results demonstrated an affordable, rapid and tailorable design and repeatable fabrication approach for strain gauges with GFavg~6.6, which has potential applications in remote sensing and structural monitoring applications.

In response to the complex social, environmental and economic situation caused by the "Terra dei Fuochi" phenomenon, the IZSM collaborated closely with the Terra dei Fuochi working group, carrying out additional monitoring surveys both on food (QR Code Campania project[30]), and on the environment (Campania Trasparente project[31]). This model was developed in the context of the experience accumulated in the field of environmental and food monitoring, and represents an innovative tool aimed at increasing knowledge of the environmental context of the Campania Region through an objective, integrated and organic synthesis of complex environmental phe-nomena and territorial dynamics. The model proposed here is useful for the global and synthetic assessment of environmental pressure on a municipal basis. As shown, it can also be applied to aggregations of municipalities. Furthermore, it can be used in the context of institutional actions for the planning and monitoring of improvements on a local or regional scale. Finally, the pro-posed municipality-based environmental pressure index represents the basis for geo-stratification of the sample in the context of population biomonitoring studies on a regional scale, as in the described biomonitoring study design applicable to the Campania Region.

Understanding the relationships between land cover/urban structure patterns and air pollutants is key to sustainable urban planning and development. In this study, we employ a mobile monitoring method to collect PM_2.5 and BC data in the city of Philadelphia, PA during the summer of 2019 and apply the Structure of Urban Landscapes (STURLA) methodology to examine relationships between urban structure and atmospheric pollution. We find that, while PM_2.5 and BC vary by STURLA class, many of the differences in pollutant concentrations between classes are not significant. However, we also find that the proportions in which STURLA components are present throughout the urban landscape can be used to predict urban air pollution. Among frequently sampled STURLA classes, gpl hosted the highest PM_2.5 concentrations on average (16.60 _± 4.29 µg/m³), while tgbwp hosted the highest BC concentrations (2.31 _± 1.94 µg/m³). Furthermore, STURLA combined with machine learning modeling was able to correlate PM_2.5 (R²= 0.68, RMSE 2.82 µg/m³) and BC (R² = 0.64, RMSE 0.75 µg/m³) concentrations with the urban landscape and spatially interpolate concentrations where sampling did not take place. These results demonstrate the efficacy of the STURLA methodology in modeling relationships between air pollution and land cover/urban structure patterns.

The air pollutant NO2 is derived largely from transportation sources and is known to cause respiratory disease. A substantial reduction in transport and industrial processes around the globe from the novel SARS-CoV-2 coronavirus and subsequent pandemic resulted in sharp declines in emissions, including for NO2. Additionally, the COVID-19 disease that results from the coronavirus may present in its most severe form in those who have been exposed to high levels of air pollution. To explore these links, we compared ground-based NO2 sensor data from 11 US cities from a two-month window (March-April) over the previous five years versus the same window during 2020 shutdowns. NO2 declined roughly 12-41% in the 11 cities. This decreased coincided with a sharp drop in vehicular traffic from shutdown-related travel restrictions. To explore this link more closely, we gathered more detailed traffic count data in one city, Indianapolis, Indiana, and found a strong correlation between traffic counts/classification and vehicle miles travelled, and a moderate correlation between NO2 and traffic related data. This finding indicates that we can use such analysis in targeting reduction in pollutants like NO2 by examining and manipulating traffic patterns, thus potentially leading to more population-level health resilience in the future.

The assessment of water quality consists of counting bacteria indicating fecal contamination or detecting the presence of pathogenic bacteria using standardized or validated methods of classical microbiology. Our present study aims to determine the bacteriological quality of drilling water in the Tandjilé region of Chad. Our method used was based on qualitative and quantitative research on suspected total coliforms, Echerichia Coli and fecal enterococci were analyzed according to the standard routine methods of the French Association for Normalization (AFNOR). Microbiological analysis shows the presence of indicators of fecal contamination such as total coliforms, Escherichia coli and fecal enterococci. The number of strains detected in 100 ml were E. coli (7 /29 samples), fecal Streptococcus (6 /29 samples) and total coliforms (29/29 samples), respectively from borehole water. The contamination rate of E. coli is 24.13%, total coliforms 100% and 20.68% of fecal enterococci in boreholes. The high number of these microorganisms is more than the values recommended by the WHO for the quality of drinking water. Corrective and urgent measures are needed to improve the quality of these water resources, rich in pathogens, which are health risks, and the causes of infectious diseases such as gastroenteritis, diarrhea, typhoid and skin diseases.

Precision agriculture is a technology used by farmers to help food sustainability amidst growing population. One of the tools of precision agriculture is yield monitoring, which helps a farmer manage his production. Yield monitoring is usually done during harvest, however it could also be done early in the growing season. Early prediction of yield, specifically for fruit trees, aids the farmer in the marketing of their product and assists in managing production logistics such as labor requirement and storage needs. In this study, a machine vision system is developed to estimate fruit yield early in the season. The machine vision system uses a color camera to capture images of fruit trees during the full bloom period. An image segmentation algorithm based on an artificial neural network was developed to recognize and count the blossoms on the tree. The artificial neural network segmentation algorithm uses color information and position as input. The resulting correlation between the blossom count and the actual number of fruits on the tree shows the potential of this method to be used for early prediction of fruit yield.

Remote sensing has been used as an important tool for disaster monitoring and disaster scope extraction, especially for the analysis of spatial and temporal disaster patterns of large-scale and long-duration series. Based on the Google Earth Engine cloud platform, this study used MODIS vegetation index products with 250-m spatial resolution synthesized over 16 days from the period 2005–2019 to develop a rapid and effective method for monitoring disasters across a wide spatiotemporal range. Three types of disaster monitoring and scope extraction models are proposed: the normalized difference vegetation index (NDVI) median time standardization model (R_{NDVI_TM(i)}), the NDVI median phenology standardization model (R_{NDVI_AM(i)(j)}), and the NDVI median spatiotemporal standardization model (R_{NDVI_ZM(i)(j)}). The optimal disaster extraction threshold for each model in different time phases was determined using Otsu’s method, and the extraction results were verified by medium-resolution images and ground-measured data of the same or quasi-same period. Finally, the disaster scope of cultivated land in Heilongjiang Province from 2010–2019 was extracted, and the spatial and temporal patterns of the disasters were analyzed based on meteorological data. This analysis revealed that the three aforementioned models exhibited high disaster monitoring and range extraction capabilities, with verification accuracies of 97.46%, 96.90%, and 96.67% for R_{NDVI_TM(i)}, R_{NDVI_AM(i)}, and _(j)R_{NDVI_ZM(i)(j)}, respectively. The spatial and temporal disaster distributions were found to be consistent with the disasters of the insured plots and the meteorological data across the entire province. Moreover, different monitoring and extraction methods were used for different disasters, among which wind hazard and insect disasters often required a delay of 16 days prior to observation. Each model also displayed various sensitivities and were applicable to different disasters. Compared with other techniques, the proposed method is fast and easy to implement. This new approach can be applied to numerous types of disaster monitoring as well as large-scale agricultural disaster monitoring and can easily be applied to other research areas. This study presents a novel method for large-scale agricultural disaster monitoring.

Neuromuscular disorders cause progressive muscular weakness, which limits upper extremity mobility and performance during activities of daily life. A dynamic arm support can improve mobility and quality of life. However, their use is often discontinued over time for unclear reasons. This study aimed to evaluate whether users of dynamic arm supports demonstrate and perceive quantifiable mobility benefits over a period of two months. Nine users of dynamic arm supports were included in this observational study. They had different neuromuscular disorders and collectively used four different arm supports. They were observed for three consecutive weeks during which they were equipped with a multi-sensor network of accelerometers to assess the actual use of the arm support and they were asked to provide self-reports on the perceived benefits of the devices. Benefits were experienced mainly during anti-gravity activities and the measured use did not change over time. The self-reports provided contextual information in domains such as participation to social life, in addition to the sensor system. However self-reports overestimated the actual use by up to three-fold compared to the accelerometer measures. A combination of objective and subjective methods is recommended for meaningful and quantifiable mobility benefits during activities of daily life.

This paper proposes a novel data processing framework dedicated to bedload monitoring in underwater environments. After calibration, by integration the total energy in the nominal bandwidth, the proposed experimental setup is able to accurately measure the mass of individual sediments hitting the aluminum plate. This require a priori knowledge of the vibration trasients in order to match a predefined dictionary. Based on unsupervised hierarchical agglomeration of complex vibration spectra, the proposed algorithms allow to accurately localize the transients corresponding to the shocks created by sediment impacts on a steel plate.

Proper satellite-based crop monitoring applications at the farm-level often require near-daily imagery at medium to high spatial resolution. The synthesizing of ongoing satellite missions by ESA (Sentinel 2) and NASA (Landsat7/8) provides this unprecedented opportunity at a global scale; nonetheless, this is rarely implemented because these procedures are data demanding and computationally intensive. This study developed a complete stream processing in the Google Earth Engine cloud platform to generate harmonized surface reflectance images of Landsat7,8 and Sentinel 2 missions. The harmonized images were generated for two agriculture schemes in Bekaa (Lebanon) and Ninh Thuan (Vietnam) during the period 2018-2019. We evaluated the performance of several pre-processing steps needed for the harmonization including image co-registration, brdf correction, topographic correction, and band adjustment. This study found that the miss-registration between Landsat 8 and Sentinel 2 images, varied from 10 meters in Ninh Thuan, Vietnam to 32 meters in Bekaa, Lebanon, and if not treated, posed a great impact on the quality of the harmonized dataset. Analysis of a pair overlapped L8-S2 images over the Bekaa region showed that after the harmonization, all band-to-band spatial correlations were greatly improved from (0.57, 0.64, 0.67, 0.75, 0.76, 0.75, 0.79) to (0.87, 0.91, 0.92, 0.94, 0.97, 0.97, 0.96) in bands (blue, green, red, nir,swir1,swir2, ndvi) respectively. We demonstrated that dense observation of the harmonized dataset can be very helpful for characterizing cropland in highly dynamic areas. We detected unimodal, bimodal and trimodal shapes in the temporal NDVI patterns (likely cycles of paddy rice) in Ninh Thuan province only during the year 2018. We fitted the temporal signatures of the NDVI time series using harmonic (Fourier) analysis. Derived phase (angle from the starting point to the cycle's peak) and amplitude (the cycle's height) were combined with max-NDVI to generate an R-G-B image. This image highlighted croplands as colored pixels (high phase and amplitude) and other types of land as grey/dark pixels (low phase/amplitude). Generated harmonized datasets that contain surface reflectance images (bands blue, green, red, nir, swir1, swir2, and ndvi at 30 meters) over the two studied sites are provided for public usage and testing.

Background: It is well known the adverse effect of mercury exposure on pregnant women and newborns. Interactions between environmental factors and individual genetic susceptibility have been identified, particularly polymorphisms of codifying genes for the Glutathione S-transferase family (GSTs). Herein, we report a case series of patients with high Hg levels in biosamples. Case Series: Fourteen cases with high Hg levels were identified. Non-occupational or home exposure risk factors were identified. All mothers reported fish consumption during pregnancy. Almost 60% of the individuals were null for either one GSTs gene. To date, in the subsequent mother-child pairs toxicology controls no signs or symptoms of poisoning were identified and most of the mercury levels decreased and are below the accepted limit. Discussion: In this case series we found some similarities with the literature; among them, the relation of Hg ratio in maternal blood and umbilical cord, a possible exposure factor is the consumption of fish during pregnancy and, the high levels of Hg may be related with susceptibility biomarkers such as GSTs gene polymorphisms. This case series highlights the need to develop studies that evaluate the interactions between environmental factors and individual genetic susceptibility. Additionally, the importance of evaluating which Colombian fish species present the highest levels of Hg.

This paper describes a multi-channel in-situ monitoring system developed to better understand defect formation signatures in metal additive manufacturing. Three high-speed imaging modes coupled with an image computer capable of processing and storing these data streams allowed an examination of defect formations signatures and mechanisms. It was found that defects later detected in X-ray computed tomography (CT) scans were related to regions with anomalous heat signatures and powder bed morphology. Automated defect detection algorithms based on these defect signatures captured 80% of defects greater than 300 µm.

High throughput multiplex serological systems enable the small developer to set up tests at small cost, for microbes for which there are no commercial tests, and for aspects which have not been addressed by them. An example is testing for Zika and Tick Borne Encephalitis virus antibodies, where antigenic cross-reactions make diagnosis problematic. Our technique variant, Suspension Multiplex Immunoassay (SMIA) allows many samples to be tested for antibodies to many antigens in a short time. Computational compensation for cross-reactions is possible if a SMIA panel contains most of the potentially cross-reacting antigens. Using antibody avidity and pattern of reactivity to whole virus and nonstructural protein, antibodies due to vaccination and infection, respectively, as well as probable degree of protection, can be determined with high throughput. These multiplex techniques hold great promise for future diagnostic development. Theoretically, even large scale serological monitoring, like blood donor pathogen testing, could be done inexpensively and rationally with multiplex serology developed in house. However, the quality control demands are steep and in most cases out of scope for a single laboratory. There remain however a number of clinical applications where in house multiplex serology can be performed with adequate quality control under high throughput conditions.

When a rotary machine is running, from which the acquired vibro-acoustic signals enable to reveal its operation status and health condition. The study proposed a DSP-based adaptive angular-velocity Vold-Kalman filtering order tracking (AV2KF_OT) algorithm with an online real-time nature for signal interpretation and machine condition monitoring. Theoretical derivation and numerical implementation of computation schemes are briefly introduced. An online real-time monitoring system based on the AV2KF_OT algorithm, which was implemented through both a digital signal processor and a user interface coded by using LabVIEW, was developed. Two experimental tasks were applied to justify the proposed technique, including (i) the detection of startup on the fluid-induced whirl performed through a journal-bearing rotor rig, and (ii) the separation of close orders from the measured signals of a multifunction transmission-element ball-bearing bench.

Wearable sensors for human physiological monitoring have attracted tremendous interest from researchers in recent years. However, most of the research was only done in simple trials without any significant analytical algorithms. This study provides a way of recognizing human motion by combining textile stretch sensors based on single-walled carbon nanotubes (SWCNTs) and spandex fabric (PET/SP) and machine learning algorithms in a realistic applications. In the study, the performance of the system will be evaluated by identification rate and accuracy of the motion standardized. This research aims to provide a realistic motion sensing wearable products without unnecessary heavy and uncomfortable electronic devices.

This research presents alternative solutions for an Energy Efficiency Management System (EEMS) serving as a framework for optimizing the energy consumption algorithm and lowering energy consumption. First, a monitoring Wireless Sensor and Actuator Network (WSAN) is used for sensing, measuring, gathering data, and modeling all the dynamic disturbance parameters of the rooms in the building. Second, integrated software for metering and controlling the processes of digital data flow is used. Third, an alternative solution is proposed to reduce energy consumption. The primary benefits of this system are real-time monitoring; rapid, alternative solutions; and the ability to make a prudent decision on how to lower energy consumption. The system shows instant and accumulated solutions for short and long-term time planning. The solutions identified can be implemented in the same buildings under the same circumstances. The universities of Majmaah and Philadelphia have buildings with similar infrastructure. The system was applied to the buildings at Philadelphia University. The results were generalized to both universities. After implementation, the energy consumption of the EEMS using WSAN (based on the monitoring was reduced up to 23% when compared to that of the initial state.

Deck inclination and vertical displacements are among the most important technical parameters to evaluate the health status of a bridge and to verify its bearing capacity. Several methods, both conventional and innovative, are used for structural rotations and displacement monitoring; no one of these does allow, at the same time, precision, automation, static and dynamic monitoring without using high cost instrumentation. The proposed system uses a common laser pointer and image processing. The elastic line inclination is measured by analyzing the single frames of a HD video of the laser beam imprint projected on a flat target. For the image processing, a code was developed in Matlab® that provides instantaneous rotation and displacement of a bridge, charged by a mobile load. An important feature is the synchronization of the load positioning, obtained by a GNSS receiver or by a video. After the calibration procedures, a test was carried out during the movements of a heavy truck maneuvering on a bridge. Data acquisition synchronization allowed to relate the position of the truck on the deck to inclination and displacements. The inclination of elastic line was obtained with a precision of 0.01 mrad. The results demonstrate the suitability of the method for dynamic load tests, control and monitoring of bridges.

In the present work, a portable device system applied in the detection and classification of different metallic ions was proposed and developed, aiming at its application in the monitoring of hydrological systems like rivers, lakes and groundwater. Considering the system features, a portable colorimetric system was developed by using a multispectral optoelectronic sensor. All the technology of quantification and classification of metallic ions using Optoelectronic Multispectral sensors was fully integrated in the embedded hardware FPGA technology and software based on virtual Instrumentation (NI LabView ®). The system was used as a colorimeter by using the chromogen reagent of 1-(2-pyridylazo)-2-naphthol (PAN) as an indicator and the results obtained together with the signal processing and pattern analysis using the method of the linear discriminant analysis, allowed to obtain excellent results in detection and classification of Pb(II), Cd(II), Zn(II), Cu(II), Fe(III) and Ni(II) ions, with almost the same level of performance in relation to those obtained from the UV-VIS spectrometers of high spectral resolution.

Outdoor lighting is becoming increasingly widespread, and residents are suffering from serious light pollution as a result. Residents’ awareness of their rights to protection has gradually increased. However, due to the sometimes-inaccessible nature of residential vertical light incidence intensity data and the high cost of obtaining specific measurements, there is no appropriate hierarchic compensation for residents suffering from different degrees of light pollution. It is therefore important to measure light pollution levels and their damage at the neighborhood scale to provide residents with basic materials for proper protection and to create more politically suitable solutions. This article presents a light pollution assessment method that is easy to perform, is low-cost, and has a short data-processing cycle. This method can be used to monitor residential zone light pollution in other cities. We chose three open areas to test the spatial variation pattern of light intensity. The results are in accordance with spatial interpolation patterns and can be fit, with high precision, using the IDW method. This approach can also be used in 3 dimensions to quantitatively evaluate the distribution of light intensity distribution. We use a mixed-use zone in Beijing known as The Place as our case study area. The vertical illumination at the windows of residential buildings ranges from 2 lux to 23 lux; the illumination in some areas is far higher than the value recommended by CIE. Such severe light pollution can seriously interfere with people's daily lives and has a serious influence on their rest and health. The results of this survey will serve as an important database to assess whether the planning of night-time lighting is scientific and whether it provides residents with a basis for the protection of their rights.

Distributed deformation based on Fiber Bragg Grating sensors or other kinds of strain sensors can be used to evaluate safety in operating periods of bridges. However, most of the published researches about distributed deformation monitoring are focused on solid rectangular beam rather than box girder—a kind of typical hollow beam widely employed in actual bridges. Considering that the entire deformation of a single-cell box girder contains not only bending deflection but also two additional deformations respectively caused by shear lag and shearing action, this paper again revises the improved conjugated beam method (ICBM) based on the LFBG sensors to satisfy the requirements for monitoring two mentioned additional deformations. The best choice for the LFBG sensor placement in box gilder is also proposed in this paper due to strain fluctuation on flange caused by shear lag effect. Results from numerical simulations show that most of the theoretical monitoring errors of the revised ICBM are 0.3%~1.5%, and the maximum error is 2.4%. A loading experiment for a single-cell box gilder monitored by LFBG sensors show that most of the practical monitoring errors are 6%~8%, and the maximum error is 11%.

This paper shows the results of applying high-resolution Unmanned Aircraft System (UAS) photogrammetric surveying on a large landslide. A real case study, where permanently installing GCPs could be complex, where natural shaped and formed land pose severe limitations in deploying ground targets with optimal geometric configuration. We analysed performances in terms of survey accuracy obtained by performing photogrammetric surveys through the Zenmuse P1 DJI optical camera and Phantom 4 Pro 2. In combination with DJI Matrice 300 UAS, the P1 camera allows direct georeferencing through GNSS observations in RTK mode. Photogrammetric surveys, performed through different georeferencing methods, have been compared. Several targets have been permanently installed on the ground over the maximum vegetation height to guarantee long-lasting reference over the years in the area, which is characterised by a diffuse short vegetation coverage. Multitemporal UAS surveys have been then compared using Digital Image Correlation (DIC) algorithms, and deformation maps have been produced. Afterwards, DIC results were compared with observations made by the GNSS ground-based permanent receivers resulting in a standard deviation of 0,077 m. Through results analysis, good accordance between ground-based GNSS observations and DIC analysis on the photogrammetric surveys have been identified for the same time span. To conclude, this type of landslide presents a moderate deformation speed; in such a case, effective deformations monitoring could be achieved using pseudo-direct georeferencing, which permitted a 0.24 m accuracy on the whole tested area.

Stream chemistry effectively integrates watershed ecosystem processes on both spatial and temporal scales. Streams of coastal areas integrate a more homogeneous, flat topography wherein there can be interactions between the stream and the body of water into which it drains, especially where tidal fluxes occur. The present study assessed water quality of Thompson Bayou, which comes to the campus of the University of West Florida in a wetland after flowing through 4 km of commercial and private property with associated impacts on water quality. Sampling was carried out for one year at eight discrete sites along Thompson Bayou from the UWF campus to the Escambia River. We used a portable field meter to measure temperature, pH, dissolved O2 (DO), and specific conductivity (SC). Except for temperature, all variables exhibited a spatial pattern of significant variation with distance, with consistent increases in DO and SC as the stream approached the river. These variables also exhibited a temporal pattern of significant seasonal variation, including—and especially—temperature. Data suggest that spatial and temporal patterns of water quality of Thompson Bayou are determined by (1) processing of water by the wetland, (2) interactions of the stream channel with upland forest stands, and (3) the tidal hydrology of the Escambia River.

Seismic monitoring in areas where induced earthquakes could occur is a challenging topic for seismologists due to generally very low signal to noise ratio. Therefore, the seismological com-munity is devoting several efforts to the development of high-quality networks around the areas where fluid injection and storage and geothermal activities take place, also following the national induced seismicity monitoring guidelines. The use of advanced data-mining strategy, such as template matching filters, auto-similarity search and deep-learning approaches is recently further fostering such a monitoring enhancing the seismic catalogues and lowering the magnitude of completeness of these areas. In this framework, we carried out an experiment where a small-aperture seismic array was installed around the gas reservoir of Collalto, in North Italy. The continuous velocimetric data, acquired for 25 days, were analysed through the application of the optimized auto-similarity search technique FAST. The array was conceived as a cost-effective network, aimed at integrating, right above the gas storage site, the permanent high-resolution Collalto Seismic Network. The analysis allowed to detect micro-events down to magnitude Ml=-0.4 within a distance of ~15km from the array. Our results confirmed that the system based on the array installation and the FAST data-analysis might contribute to lower the magnitude of completeness around the site of about 0.7.

This study reports an empirical analysis of an all-electric, Net Zero Energy Housing (NZEH) development located in a mixed-humid climate zone (4A, Virginia, USA). Circuit-level energy monitors were used to measure energy consumption and energy production data (solar photovoltaic) at 1-hr intervals in six identical apartments over 24 months. The study employs a multi-step case study methodology to a) empirically evaluate energy consumption and production data, b) identify the temporal variability of energy consumption and production data at different time scales, c) understand the impact(s) of weather and human-building interaction on energy consumption and production, and d) synthesize the study’s “lessons learned” toward data-driven recommendations for future NZEH researchers and practitioners. The study found that the development’s net zero energy goal was achieved in three of six case units and that NZEH housing performance was more influenced by human-building interaction than weather variability. The analysis also found the solar photovoltaic (PV) performance to be reliable across the sampled units over the periods of measurement, suggesting that solar PV could be oversized as an approach to overcome verifiability in HBI and achieve NZEH performance goals.

Resistance spot welding is an established joining process in the production of safety-relevant components in the automotive industry. Therefore, a consecutive process monitoring is essential to meet the high-quality requirements. Artificial neural networks can be used to evaluate the process parameters and signals to ensure the individual spot weld quality. The predictive accuracy of such algorithms depends on the provided training data set and the prediction of untrained data is challenging. The aim of this paper is to investigate the extrapolation capability of the multi-layer perceptron model. That means, that the predictive performance of the model will be tested with data that clearly differs from the training data in terms of material and coating composition. Therefore, three multi-layer perceptron regression models were implemented to predict the nugget diameter from process data. The three models were able to predict the trained datasets very well. The models, which were provided with features from the dynamic resistance curve predicted the new dataset better than the model with only process parameters. This study shows the beneficial influence of the process signals on the predictive accuracy and robustness of artificial neural network algorithms. Especially, when predicting a data set from outside of the training space.

Ukraine is an associate member of the European Union and in the coming years it is expected that all the data and services already used by European Union countries will become available for Ukraine. An important program, which is the basis for building European monitoring services for Smart Cities, is the Copernicus program. The two most important services of this program are Copernicus Land Monitoring Service (CLMS) and Copernicus Atmosphere Monitoring Service (CAMS). CLMS provides important information on Land Use in Europe. In the context of Smart Cities, the most valuable one is the Urban Atlas service, which is related to local CLMS services and provides a detailed digital city plan in vector form, which is segmented into small functional areas classified by the CORIN nomenclature. The Urban Atlas is a geospatial layer with high-resolution, which is built for all European cities with a population of more than 100,000 that combines high-resolution sat-ellite data, city segmentation by blocks and functional areas, important city infrastructure, etc. This product is used as a basis for city planning and obtaining analytics on the most important indicators of city development including air quality monitoring. For Ukraine, such geospatial products are not provided under the Copernicus program. It is important to start work on its development and implementation as early as possible, so that when the first city atlas appears, Ukraine will be ready to work with it together with the European community. This requires preparing the basis for na-tional research and training national stakeholders and users to use this product. To make this happen it’s necessary to have national geospatial product, which can be used as an analogue of the city atlas. In this article authors analyzed the existing methods of air quality assessment and assessment of the SDG indicator 11.6.2 achieving for European cities, based on which the indicator 11.6.2 for Ukraine for 5 years was evaluated for the first time. The obtained results are analyzed and the values of indicator 11.6.2 for Ukraine are compared with European countries.

One of the key geophysical technologies for the energy industry during energy transition to zero footprint is fluid imaging. Knowledge of fluid distribution allows better, more optimized production reducing thus CO2 footprint per barrel produced and for CO2 storage the knowledge of where stored fluids go is mandatory to monitor reservoir seals. Electromagnetic is the preferred way to image fluid due to its strong coupling to the fluid resistivity. Unfortunately, acquiring and interpreting the data takes too long to contribute significantly to field operation and cost optimization. Using artificial intelligence and Cloud based data acquisition we can reduce the operational feedback to near real time and for the interpretation to close to 24 h. This then opens new door for the usefulness of this technology from exploration, monitoring and allows the application envelope to be enlarged to much noisier environment where real time acquisition can be optimized based on the acquired data.

In fisheries monitoring, catch is assumed to be a product of fishing intensity, catchability, and availability, where availability is defined as the number or biomass of fish present and catchability refers to the relationship between catch rate and the true population. Ecological monitoring programs use catch per unit of effort (CPUE) to standardize catch and monitor changes in fish populations; however, CPUE is proportional to the portion of the population that is vulnerable to the type of gear that is used in sampling, which is not necessarily the entire population. Programs often deal with this problem by assuming that catchability is constant, but if catchability is not constant, it is not possible to separate the effects of catchability and population size using monitoring data alone. This study uses individual-based simulation to separate the effects of changing environmental conditions on catchability and availability in environmental monitoring data. The simulation combines a module for sampling conditions with a module for individual fish behavior to estimate the proportion of available fish that would escape from the sample. The method is applied to the case study of the well-monitored fish species Delta Smelt (Hypomesus transpacificus) in the San Francisco Estuary, where it has been hypothesized that changing water clarity may affect catchability for long-term monitoring studies. Results of this study indicate that given constraints on Delta Smelt swimming ability, it is unlikely that the apparent declines in Delta Smelt abundance are due to an effect of changing water clarity on catchability.

Monitoring of the surface operations using movement and surveying radar (MSR) can prevent loss of life, equipment, production and loss of the mine. Slope monitoring using MSR is an important aspect of open-pit mining as it provides real-time movement of deformation data for the slope. It is therefore important that the radar is accurately geo-referenced in order to provide accurate real-time movement data. Geo-referencing is defined as the process of determining an instrument’s position (in the form of Easting, Northing, Height) as well as the orientation with respect to the mine’s local coordinate system. This helps in getting geo-referenced data points from the radar that are identified by a unique set of coordinates in relation to the mine’s coordinate system which allows the radar to track movement for a specific set of coordinates. In this research, we assess the performance of geo-referencing a radar using the total station method and compare it with the integration of Advance Navigation – Spatial Dual GPS system connected via RS422 on the MSR. This includes usage of the Spatial Dual navigation coordinates output to calculate the radar’s position relative to the mine local coordinates and mapping the radar’s azimuth, elevation and Range (Az, El and Rl) values to the measured pit-slope data points. Furthermore, a comparison of key attributes of both methods of geo-referencing is performed using a matrix system and giving an overall performance appraisal of both systems. Integrating a navigation system allows the radar to have an auto geo-referencing functionality that will reduce the time spent in completing this process. The findings reveal that the GPS obtained a higher score than the total station with prism method on the weighted matrix system. The total station was found to be more accurate than the GPS however, the deployment time for the GPS is quicker than that of the total station. This is important for different operation such as strip and open-pit mining to choose the preferred method of geo-referencing depending on the level of accuracy required.

Monitoring the health of coral reefs is essential to understand the damaging impacts of anthropo-genic climate change. Non-invasive methods to survey coral reefs are the most desirable and op-tics-based surveys, ranging from simple photography to multispectral satellite imaging are well es-tablished. Herein, we review these techniques, focusing on their value for coral monitoring and health diagnosis. A new, low-cost hyperspectral imaging technique using linear variable filters is also described. This system is capable of simultaneously producing hyperspectral and photogrammetric outputs, which provides integrated information of reef structure and physiology.

: This paper presents a couple of meal monitoring systems for senile dementia patients by using electronic weight and temperature sensors. These monitoring systems enable to convey the information of the amount of meal taken by the patients in real-time via wireless communication networks onto the mobile phones of their families or nurses in charge. Thereby, the nurses can easily spot the most desperate patient to take care of while the families can have relief to see the crucial information for survival of their parents at least three times a day. Meanwhile, the senile dementia patients tend to suffer the burn of their tongues because they can hardly recognize the temperature of hot meals served and therefore avoid the burn of tongues. This phenomenon can be discarded by utilizing the meal temperature monitoring system which displays alarm to the patients when the meal temperature is above the reference. These meal monitoring systems can be easily implemented by utilizing low-cost sensor chips and Arduino UNO boards so that elder-care hospitals and nursing homes can afford to exploit them with no additional cost. Hence, we believe that the proposed monitoring systems would be a potential solution to provide a great help and relief not only for the professional nursing nurses working in elder-care hospitals and nursing homes, but also for the families of the dementia patients.

The population dynamics of Hazel Grouse was studied by presence/ absence recording at stationary sites along fixed routes (110 km) during 1972-2019 in the central part of the Bohemian Forest (Šumava, Czech Republic). The 100-km² study area covered altitudes between 600 m (Rejstejn) and 1,253 m a.s.l., (mount Sokol). Our data base contained indices of Hazel Grouse occupancy: positive sites/ controlled sites for a yearly increasing number of Hazel Grouse occurrence sites (N = 134) for 48 years. We used a loglinear Poisson-regression method to analyze the long-term population trend for Hazel Grouse in the study area. In the period 1972 to 2006 we found a stable Hazel Grouse population (p = 0.83). From 2006-2007 to 2019, the population index dropped (-3.8% per year, p &lt; 0.05) for the last 13 years. This decline is assumed to be influenced by habitat loss due to succession resulting in older, more open forest stands, by strongly increasing forestry and windstorm “Kyrill” followed by clear cutting, bark-beetle damage, and removal of pioneer trees in spruce plantations, which diminished buds and catkins, the dominant winter food. The influence of disturbance by increasing touristic activities and/or predation is discussed. Our results could help to optimize conservation efforts for Hazel Grouse in the Bohemian Forest.

This paper presents preliminary operational performance results of a pilot grid-connected photovoltaic (PV) system designed and installed on the rooftop of the Ministry of Petroleum, Energy and Mining headquarter in Nouakchott (latitude of 18.1°N and the longitude of 16.0°W), Mauritania. The aim is for the government to demonstrate the relevance of using solar energy and to encourage the uptake of solar PV technology for commercial and residential building applications in Mauritania.. In this study, the grid-connected PV system has a peak power of 48 kW and the performance monitoring was carried out during one year, with a system that allow to measure DC power, inverter and system conversion efficiency, energy generated by the PV arrays, solar radiation in the inclination plane of panels, ambient temperature and module temperature. During this period, the PV plant was found to supply 65,668 kWh to the grid. The final yield ranged from 3.91 to 5.09 kWh/kWp/day. The performance ratio was found to vary from 69.69% to 89.35% and the annual capacity factor was found to be 19%. Finally, performance parameters were compared with other PV plants installed in the same region of Northern Africa. The outcome of this work is deemed important in assisting accurate PV system design and decision-making.

The generation of vortices around bridge piers can lead to removal of riverbed materials from around piers, especially during flood events and heavy rainfalls, which can compromise the stability of the bridge and consequently its failure, if not properly detected and mitigated. Bridge failures pose serious threats to the local socio-economic and public safety and can cost lives. As such, real-time monitoring and early warning systems for scour-induced bridge failure can serve as a vital tool to protect the community and civil infrastructure against disastrous events. Vibration-base monitoring of bridge scour is an attractive option due to its low cost and relatively easy installation without the need to block the road and close the bridge to traffic. While limited number of previous studies have shown the capabilities of acceleration-based monitoring techniques in this area of research, they generally lack a rigorous framework for data analysis within and relating those to evaluate scour. This paper is an attempt to provide such framework that would enable a fast and low-cost analysis of vibration data within a physical modelling study on a simplified bridge pier. To achieve this, three experiments were conducted on an ideal single-pier scaled model bridge in a hydraulic flume, where water flows at a velocity near the critical velocity for the sand bed which in turn generates a scour hole around the pier. Then, the vibration data recorded using two mounted wireless accelerometers, were used to conduct an operational modal analysis through which the natural frequencies are extracted. The extracted natural frequencies and measured scour depths are then used to provide a chart that relates these two parameters. The results of this study showed the promising capability of the vibration-based data analysis in finding this relationship, indicating an up to around 30-50% reduction in natural frequencies as a result of around 50% scour ratio (ratio of maximum scour depth to buried depth), and beyond 50% scour ratio the natural frequencies remain constant. While the data presented in this paper are preliminary, they clearly show a promising potential for application in real-time monitoring of bridge stability under the effect of local scour and further works are underway to enrich the experimental data and empower the proposed methodologies at the laboratory scale.

COVID-19 pandemic event requires a rapid response from various organizations at the international and national levels. One important response is the provision of information sharing facilities and monitoring of the spread of cases around the world, JHU CSSE developed the Dashboard in January 2020 and followed by WHO the same month for the WHO COVID-19 dashboard. Both dashboards have distributed information as expected by the user with their respective pros and cons. JHU CSSE Dashboard provides faster information with good access to mobile device users even though the display and color selection are less attractive. Information on the WHO COVID-19 Dashboard is often late but more data appearances and variations and comparisons between countries can be made. In the Indonesian context, ESSC for COVID-19 Geoportal as Esri Indonesia initiative has been developed with the support of data and information from various parties and developed with the principles of big data management which are fully supported by adequate spatial portal developer software from Esri. Particularly in Indonesia, there is not yet an adequate system to support spatial based decision making at the local level, therefore the development of a GIS dashboard to support provincial and district governments is highly recommended.

Space-borne Synthetic Aperture Radar (SAR) Interferometry (InSAR) is now a key geophysical tool for surface deformation studies. The European Commission’s Sentinel-1 Constellation began acquiring data systematically in late 2014. The data, which are free and open access, have global coverage at moderate resolution with a 6 or 12-day revisit, enabling researchers to investigate large-scale surface deformation systematically through time. However, full exploitation of the potential of Sentinel-1 requires specific processing approaches as well as the efficient use of modern computing and data storage facilities. Here we present LiCSAR, an operational system built for large-scale interferometric processing of Sentinel-1 data. LiCSAR is designed to automatically produce geocoded wrapped and unwrapped interferograms and coherence estimates, for large regions, at 0.001° resolution (WGS-84 system). The products are continuously updated in a frequency depending on prioritised regions (monthly, weekly or live update strategy). The products are open and freely accessible and downloadable through an online portal. We describe the algorithms, processing, and storage solutions implemented in LiCSAR, and show several case studies that use LiCSAR products to measure tectonic and volcanic deformation. We aim to accelerate the uptake of InSAR data by researchers as well as non-expert users by mass producing interferograms and derived products.

Wi-Fi tethering using a mobile device (e.g., a smartphone or a tablet) as a hotspot for other devices has become a common practice. Despite the potential benefits of Wi-Fi tethering, the open source nature of mobile operating systems (e.g., Google Android) can be abused by a selfish device to manipulate channel-access parameters to gain an unfair advantage in throughput performance. This can cause serious performance problems within a well-planned Wi-Fi network due to an unauthorized selfish or misconfigured tethering device interfering with nearby well-planned access points (APs). In this paper, we demonstrate that the selfish behavior of a tethering node that adjusts the clear channel assessment (CCA) threshold has strong adverse effects in a multi-AP network, while providing the selfish node a high throughput gain. To mitigate this problem, we present a passive online detection scheme that identifies the network condition and detects selfish tethering nodes with high accuracy by exploiting the packet loss information of on-going transmissions. To the best of our knowledge, this is the first research to consider the problem of detecting a selfish tethering node in managed Wi-Fi networks.

To cope the high glycemic variability (GV) is crucial in the management of multiple daily insulin (MDI) in diabetes. We compared the effect of low dose metformin 750mg/d adding vildagliptin 100mg/d (DPP4+LMET) or the high dose metformin 1500mg/d (HMET), in type 2 diabetes (T2D) with MDI, evaluating GV by continuous glucose monitoring (CGM). Single center, open-label, 12 weeks - 2 period crossover design. Twenty T2D with inadequately controlled (7.0% <HbA1c ≦9.0%) with MDI + LMET were enrolled. Primary endpoints were GV and hypoglycemia derived from CGM performed after each 12 weeks treatment periods. There was no significant difference in HbA1c, body weight changes, total daily dose of insulin. DPP4+LMET compared to the HMET, significantly reduced the calculated GV value, mean (7.15±1.3 vs 7.82±1.6, p<0.05), standard deviation (1.78±0.55 vs 2.27±1.11, p=0.03), continuous overlapping net glycemic action (6.44±1.28 vs 7.12±1.69, p<0.05), J-Index (26.7±11.0 vs 34.9±19.8, p<0.05), high blood glucose index (3.01±1.96 vs. 6.73±4.85, p=0.02), and mean amplitude of glycemic excursions (4.53±1.35 vs 5.50±2.34, p=0.03). The GV metrics with hypoglycemia and nocturnal hypoglycemia were not significantly different. DPP4+LMET decreased GV associated with hyperglycemia. Adding DPP4 inhibitor to the lower dose of metformin is an alternative approach to the stable GV in MDI.

An increasing global aridification due to climate change has made the health monitoring of vegetation indispensable to maintaining the food supply chain. Cost-effective and smart irrigation systems are required not only to ensure the efficient distribution of water, but also to track the moisture of plant leaves, which is an important marker of the overall health of the plant. This paper presents a novel electromagnetic method to monitor the water content (WC) and characterization in plant leaves utilizing the absorption spectra of water molecules in the terahertz (THz) frequency for four consecutive days. We extracted the material properties of leaves of eight types of pot herbs from the scattering parameters, measured using a material characterization kit in the frequency range of 0.75 to 1.1 THz. From the computed permittivity, it is deduced that the leaf specimens increasingly become transparent to the THz waves as they dry out with the passage of days. Moreover, the loss in weight and thickness of leaves were observed due to the natural evaporation of leaf moisture cells and change occurred in the morphology of fresh and water-stressed leaves. It is also illustrated that loss observed in WC on day 1 was in the range of 5\% to 22\%, and increased from 83.12\% to 99.33\% on day 4. Furthermore, we observed an exponential decaying trend in the peaks of the real part of the permittivity from day 1 to 4, which was reminiscent of the trend observed in the weight of all leaves. Thus, results in paper demonstrated that timely detection of water stress in leaves can help to take proactive action in relation to plants health monitoring, and for precision agriculture applications, which is of high importance to improve the overall productivity.