This paper deals with the problem of real-time management of Smart Grids. For this sake, the energy management is integrated with the power system through a telecommunication system. The use of Multiagent Systems leads the proposed algorithm to find the best-integrated solution, taking into consideration the operating scenario and the system characteristics. The proposed technique is tested with the help of an academic microgrid, so the results may be replicated.

Based on K-ε Standard Wall turbulence model (2-Equation) and Navier-Stokes (N-S) equations defined for incompressible fluids, fluid flow behaviour around hyperloop pods in an evacuated tube was simulated using ANSYS fluent solver assuming steady state and two dimensional conditions. In this research, to develop the case studies, using combination of different head and tail shape profile, four kind of hyperloop pods were developed with the aid of SolidWorks. These four pods have been investigated for their aerodynamic behaviour as four different case scenarios. The results of simulation depicts that an atmospheric pressure of 100 Pa with blockage ratio of 0.36 in tube provides the best possible aerodynamic behaviour for the designed hyperloop pod models. This research finds that overall aerodynamic behaviour of hyperloop pods can be varied by changing the head and tail shape profile of pods and a particular combination of head and tail shape profile can provide optimally best aerodynamic capabilities. Thus, this research paper provides a novel method of obtaining best aerodynamic capabilities in hyperloop pods by designing head profile optimally in combination with tail profile. This outcome will provide major contribution towards the development of hyperloop pods in future with better aerodynamic behaviour resulting in lesser electrical energy required to propel the hyperloop pods in evacuated tube.

In this paper, a thermodynamic investigation is done on a Kalina-flash cycle. This work is initially validated with the Kalina cycle power plant, Wich is commissioned in Husavic. Low-temperature Kalina-flash is considered for this study. This cycle is working with the ammonia-water mixture. The Kalina-flash cycle was optimized in the view of exergy and thermal efficiency. A multi-objective genetic algorithm is used to accomplish optimization. The optimum values of the objective functions are observed to be 40.20 and 11.70% respectively. At last, The influence of the separator inlet dryness fraction, basic ammonia mass fraction, temperature and flash pressure ratio on the first and second law efficiencies are analysed.

This article is devoted to a bibliometric analysis of IEEE Energy Internet and Energy Systems Integration Conference proceedings posted in IEEE Xplore in 2017-2021. The main objective of the study was to identify the actual research issues on the Energy Internet topic. Author Keywords, INSPEC Controlled Terms, and terms compiled from n-grams derived from conference papers title and abstract texts were used to describe the actual issues. The terms were clustered using VOSviewer, and the terms included in each cluster were treated as a description of the actual issues. Brief descriptions of several publications relevant to the issue in question were given for task detail. The actual issue, which in my opinion deserves further, more detailed analysis, is proposed.

This paper explores the latest developments in electrolysis technology, a key player in the transition to sustainable energy systems. Electrolysis, despite currently contributing a small share to global hydrogen production, holds immense potential for producing green hydrogen. The study delves into the efficiency of electrolysis systems, emphasizing ongoing efforts to enhance energy conversion rates. It investigates the impact of high-temperature electrolysis on reducing electricity consumption, thus making the process more efficient. The paper discusses the various challenges in the research on water electrolysis and underscores the critical role electrolysis plays in integrating renewable energy sources. The study emphasizes the need for continuous advancements in electrolysis technology to bridge existing gaps, making a compelling case for its pivotal role in the green hydrogen revolution.

Designing the future energy supply in accordance with ambitious climate change mitigation goals is a challenging issue. Common tools for planning and calculating future investments in renewable and sustainable technologies are often linear energy system models based on cost optimisation. However, input data and the underlying assumptions of future developments are subject to uncertainties that negatively affect the robustness of results. This paper introduces a quadratic programming approach to modifying linear, bottom-up energy system optimisation models in order to take cost uncertainties into account. This is accomplished by implementing specific investment costs as a function of the installed capacity of each technology. In contrast to established approaches like stochastic programming or Monte Carlo Simulation, the computation time of the quadratic programming approach is only slightly higher than that of linear programming. The model’s outcomes were found to show a wider range as well as a more robust allocation of the considered technologies than the linear model equivalent.

The paper describes and analyzes the performance of a new thermoelectric generation system based on the use of Peltier cells inserted in the ducts of the air conditioning equipment. The hot and cold air streams that flow in the two separated sections of an air conditioning system are used to create a thermal gradient between the two faces of the Peltier cells. Hot and cold air flow inside the A/C unit are driven to a built in thermal chamber where the Peltier cells are placed. Peltier cells are incrusted into an insulation wall that separates the two sections of the chamber through which hot and cold air streams are flowing. The so designed configuration allows the Peltier cells to generate electric current. The study has been run for constant cold air temperature and variable hot air temperature, resulting in a variable performance of the thermoelectric generator. Theoretical study has been completed with experimental tests to determine real performance of the thermoelectric unit. Efficiency of the thermoelectric generator has been found to be linearly dependent on the temperature difference between hot and cold air subsections of the chamber. Maximum efficiency, however, is limited by the hot air stream temperature, since in real conditions ambient temperature cannot overpasses a specific value. For standard operational conditions, 5º C and 45º C for the cold and hot air streams, the thermoelectric generator operates at 44% of the maximum efficiency attainable.

The transportation sector is a significant source of greenhouse gas emissions. Electric vehicles (EVs) have gained popularity as a solution to reduce emissions, but the high load of charging stations poses a challenge to the power grid. Nuclear-Renewable Hybrid Energy Systems (N-RHES) present a promising alternative to support fast charging stations, reduce grid dependency, and decrease emissions. However, the intermittent problem of renewable energy sources (RESs) limits their application, and the synergies among different technologies have not been fully exploited. This paper proposes a predictive and adaptive control strategy to optimize the energy management of N-RHES for fast charging stations, considering the integration of nuclear, photovoltaics, and wind turbine energy with a hydrogen storage fuel cell system. The proposed dynamic model of a fast-charging station predicts electricity consumption behavior during charging processes, generating probabilistic forecasting of electricity consumption time-series profiling. Key performance indicators and sensitivity analyses illustrate the practicability of the suggested system, which offers a comprehensive solution to provide reliable, sustainable, and low-emission energy to fast-charging stations while reducing emissions and dependency on the power grid.

To help reduce the impact of geohazards, an innovative landslide early-warning technology based on an energy demodulation-based fiber optic sensing (FOS-LW for short) technology, is introduced in this paper. FOS-LW measures the energy change in a sensing fiber at the segment of micro-bending, which can be caused by landslide movements, and automatically raises an alarm as soon as the measured signal intensity in the fiber reaches a pre-set threshold. Based on the sensing of micro-bending losses in the fiber optics, a two-event sensing algorithm has been developed for the landslide early-warning. The feasibility of the FOS-LW technology is verified through laboratory simulation and field tests. The result shows that FOS-LW has some unique features such as the graded alarm, real-time responses, remote monitoring, low cost and passive optical network, and can be applied in the early-warning of landslides.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

This study advances the field of solar irradiance nowcasting by introducing a discrete-level classification approach, diverging from traditional continuous measurement methods. Grounded in a need for cost-effective and modular solutions, the research employs high-resolution computer vision coupled with a deep learning framework to predict Direct Normal Irradiance (DNI). By harnessing the capabilities of a Logitech C900 1080p HD camera and an NVIDIA Jetson module, the study achieves real-time data processing, pivotal for CSP systems' operational efficiency. The core of the methodology is the ResNet-50 convolutional neural network, refined via transfer learning on a bespoke dataset, culminating in a predictive accuracy of 85.78%. This discrete classification model contrasts with conventional, costly instruments like the MS-57, offering a novel and accessible alternative for DNI estimation. Such innovation not only demonstrates high predictive accuracy but also signifies a shift towards less resource-intensive and more adaptable solar energy forecasting tools, contributing a significant leap towards optimizing renewable energy systems.

This paper proposed a damping method for enhancing oscillatory stability performance of power systems with high penetration of renewable energy by a resilient wide-area multi-mode controller. The resilient wide-area multi-mode controller is used as an additional controller in a renewable energy system with a battery energy storage to enhance the damping of the critically weak modes. The weak modes are likely to be triggered in the event of line outages or any other disturbances, and the system may become unstable in the absence of proper corrective and preventive control. A firefly algorithm has been employed to design such a controller. Eigenvalue analysis and time-domain simulation are used to analyze the performance of the proposed controller in a realistic representative power system. From the simulation results, it is evident that the oscillatory stability performance of the renewable rich power system can be enhanced with the proposed control to keep the damping on critical modes to the industrial standards. Furthermore, renewable energy penetration can be increased significantly in the realistic representative system by introducing the proposed controller without disturbing the oscillatory stability margin.

A new circuit model of the self-powered device for heart rate measurement is presented in this paper. This device consists of piezoelectric energy harvester (PEH), power management circuit (PMC) with energy storage, microcontroller, Photoplethysmography (PPG) sensor, and Wi-Fi module. The PEH is placed under the insole to harvest the pressure energy from human foot-step to generate ac power. In our model, a PEH is represented by sine voltage source, where its parameters were taken from experiments with 20 volunteers. The PMC is simplified by a switch with gain δ placed in series with the main circuit. The model of the main circuit is RC elements in parallel, where C is the capacitance of the storage device, and R is the equivalent parallel resistance of the microcontroller, PPG sensor, and Wi-Fi modules, respectively. The value of R depends on the power and current absorbed by those modules during sleep, deep sleep, sense, and transmit modes which collected from the datasheet. Finally, the proposed circuit model of the self-powered device was built and simulated in SPICE. The simulation results were compared with the laboratory experiment using commercial devices. Based on the results, the proposed model had small gaps compared to the real self-powered devices in terms of average current, voltage, power and efficiency.

With the increasing prominence of renewable energy sources providing flexibility to the power grid, there is a growing recognition of the need to expand virtual Energy Storage Systems (ESS) to replace traditional ESS, which faces challenges in terms of supply and scalability. Grid-connected microgrids can supply power stably and are being built, so they can be used as virtual ESS to provide flexibility to the power system. This study proposes an approach to determine the optimal Power Conversion System (PCS) and battery capacity for a Virtual Energy Storage System(VEES) based on a grid-connected microgrid incorporating Photovoltaic (PV) and ESS. In this paper, it is assumed that microgrids can provide flexibility to the grid by participating in the energy trading market, there are corresponding profits and penalties for order. Numerical examples are performed to demonstrate the effectiveness of the proposed method.

The purpose of this paper is to describe a new way of producing renewable energy based on fjords as a water heater. We will call this system the Water-thermal Energy Production System (WEPS), because the basic idea is to extract heating and cooling energy from water. Although a prototype of WEPS has existed in Norway for more than ten years, a WEPS currently in operation has not been financially analyzed in the literature. Coastal parts of Norway have a potential of 5 TWh of profitable WEPS-facilities [9], due to convenient access to fjords containing water with stable all-season temperatures of about 4–12C when the depth of the water is about 50 meters. This stability of the water temperature makes it possible to extract energy from the fjord in a very efficient way. The potential for economically-profitable WEPS in other parts of the world has not been estimated. In order to answer such a question, more research is required. We have conducted a case study of a WEPS located in the Norwegian municipality of Eid. This is the first full-scale Norwegian WEPS, and it has been operating since 2006. The nascent years have passed, and the technology has been in operation for some years. In this paper, we have made an estimate of the business profitability and the external effects based on past empirical evidence and some assumptions about future development in some key figures. The results suggests that WEPS-Eid has been a profitable investment carrying a positive internal rate of revenue, even if the present underutilization in production capacity will continue in the future. Stability in energy prices for heating purposes has also gained customers compared to the more volatile prices of alternative renewable energy, like hydropower or wind turbines. The negative, external effects in the operating phase from WEPS-Eid are insignificant. Despite the significant profitability of the WEPS facility in Eid, there are two main obstacles for new entrants. There is a lack of relevant operational information for potential investors due to few facilities. This leads to uncertainty, and investments in WEPS appear as a risky business. Secondly, construction of a WEPS requires both big financial investments in digging and facilitating long trenches for a pipeline system and time and effort spent on acquiring the licenses needed for doing this work. A coordinating unit is probably required in order to get the necessary public and private licenses and to reduce fixed costs by coordinating other tasks in the same trenches, like pipes for water and sewer, fiber cables and tele-cables. In Eid, the local municipal administration was the coordinating unit.

Hybrid Renewable Energy Systems (HRES) integrate renewable sources, storage, and optionally conventional energies, offering an eco-friendly solution to fossil fuels. Microgrids (MGs) bolster HRES integration, enhancing energy management, resilience, and reliability at various levels. This study, emphasizing the need for refined optimization methods, investigates three themes: renewable energy, microgrid, and multiobjective optimization (MOO), through a bibliometric analysis of 470 Scopus documents from 2010-2023, analyzed with SciMAT software. It segments the research into two periods, 2010-2019 and 2020-2023, revealing a surge in MOO focus, especially in the latter period, with a 35% increase in MOO-related research. This indicates a shift towards com-prehensive energy ecosystem management that balances environmental, technical, and economic elements. The initial focus on MOO, genetic algorithms, and energy management systems has expanded to include smart grids and electric power systems, with MOO remaining a primary theme in the second period. The increased application of Artificial Intelligence (AI) in optimizing HMGS within the MOO framework signals a move towards more sustainable, intelligent energy solutions. Despite progress, challenges remain, including high battery costs, the need for reliable MOO data, the intermittency of renewable energy sources, and HMGS network scalability issues, highlighting directions for future research.

Although impending urbanization is a well-acknowledged problem, there is a rising concern about how the urban forms will change and what can be the impacts on the global energy demand. As hubs of economic, social and cultural activities, cities are major energy consumers and GHG emissions. Energy consumption is a technical or a spatial problem? From Newman and Kenworthy to today, several studies have tried to shed light on this nexus. In this work, the controversial paradigm of urban density is discussed as a key component of the fight against climate change impacts. Concerning energy consumption, an in-depth bibliometric analysis is developed to identify the interdependencies of the terms. As a key ‘promise’ of an efficient urban configuration, density has been the core of diverse studies but with still under exploration arguments. This work provides a way forward for planners seeking to design strategies related to dense urban tissues exploring controversial paradigms as a key solution for energy-efficient problems.

In small-scale hydropower scheme, the most important component is electro-mechanical equipment. Since cost contribution of this component is high because hydrokinetic projects require negligible civil works. Turbine and alternator contribute major fraction of the hydrokinetic projects. Thus, there is a requirement to estimates the electromechanical equipment cost for the hydrokinetic hydropower scheme. The present paper investigates design parameters of the hydrokinetic turbines and intends to develop cost correlation which depends on most critical parameters of hydropower sites such as velocity and power capacity. In this present work, three zero head turbines are considered including straight blade Darrieus, two Stage Savonius, and Gorlov Helical. The size and cost of major components have been calculated based on material, manufacturing, research and design, and assembly costs. Based on cost and site parameters, cost correlation has been developed. The obtained cost has been validated with available zero head turbines in the market and installed projects. A techno-economic analysis has been carried out to select economical hydrokinetic turbine for river and canal application.

This article proposes a particular strategy to proceed with a progressive electrification of public transport systems in cities. Starting from a bus operation model, the possible electrification of two routes is analysed, one urban and another extra-urban in the city of Pisa. An estimate is made of the energy uses associated with certain operating modes. The maximum level of consumption is estimated at approximately 280 kWh per day per bus for the urban route and excluding some special days, less than 215 kWh per day for the extra-urban route, for which a hybrid bus is proposed. Starting from an estimate of the daily consumption for the management of the two routes, the sizing of a photovoltaic system distributed on some modular shelters which serves to power the same routes is carried out. The resulting system has a power of the order of 190-200 kW. The modular solution is also outlined, and an installation is proposed. The analyzed case lends itself to being easily replicated.

Ultralight power generation equipment has high requirements for the power density, continuous operation, and transient stability of the whole machine, and there is a direct conflict between high power density design and substantial stability control in the power unit design. In order to meet the power density requirements of ultra-light power stations, three main problems need to be solved, namely engine speed oscillation and flameout in the process of load power mutation, matching of the generator and engine torque, and stabilizing the voltage waveform of the AC output end. In this paper, we proposed an exquisite control strategy for ultralight power generation systems in engines, generators, and inverters. The effectiveness and practicability of the proposed strategy are verified by both simulation and experiment. The results show that the proposed control strategy can effectively solve the instability problem of the ultralights generator set and improve the stability of the system, where the response recovery can be achieved within 0.9 seconds under the condition of total load increase or decrease, and the mismatching degree of the generator following the engine is reduced by 90%. The strategy could also guarantee long-term stable operation with high-quality electrical energy output.

Friction and wear take place on two solid surfaces in sliding contact as a result of the mechanical, thermal and chemical interactions with the participation of environmental species. Electron microscopy and the associated spectroscopic analyses are powerful in probing these mechanisms in spatial resolutions from micro to atomic scale. This article provides a review of the author’s work in the wear and friction mechanisms of PVD hard coatings in which various SEM- and TEM-based microscopic and spectroscopic techniques were employed. Understanding on the failure mechanisms and the origin of self-adaptive friction has been improved to nano-scale. Other related issues are also discussed, such as sample preparation techniques for cross-sectional electron microscopy, energy dispersive X-ray spectroscopy and electron energy loss spectroscopy.

This study focused on the predictive models incorporating machine learning techniques that induce new dynamics for forecasting energy generation, enabling effective planning, financing, and system monitoring. The research developed a machine learning-based power generation prediction model tailored explicitly for Kenya's Garissa solar power plant. The selected model demonstrated a root mean squared error of 5.23 during evaluation, resulting in a prediction accuracy of 90.42%. This high accuracy indicates that the model can be relied upon for precise generation prediction, facilitating effective planning, and system performance monitoring

This study aimed to evaluate a cantilever beam-type piezoelectric energy harvester operating on train-induced vibrations for powering Wireless Sensor Networks (WSNs) used in railway track monitoring systems. The harvester's behaviors under different conditions are simulated in MATLAB using the analytical model. Natural frequency, maximum deflection, and stress were calculated with greater precision using eigenfrequency and stationary analysis using COMSOL Multiphysics. At a base excitation of 2 g and a resonant frequency of 4.38 Hz, the simulated results showed that the developed energy harvester prototype could generate up to 14 V of AC output voltage and 550 mW of output power. These findings highlight the promising potential of the proposed energy harvester for transforming train mechanical energy into electrical power. This energy harvester's viability and dependability for real-world applications in monitoring railway tracks are supported by developed analytical and simulation models.

Device-to-device (D2D) communication is an essential part of the future fifth generation (5G) system that can be seen as “network of networks”, consisting of multiple seamlessly integrated radio access technologies (RATs). Public safety communications, autonomous driving, social-aware networking, and infotainment services are example use cases of D2D technology. High data rate communications and use of several active air interfaces in the described network create energy consumption challenges for both base stations and the end user devices. In this paper, we review the status of 3GPP standardization and define a set of application scenarios. We use the recent models of 3GPP Long Term Evolution (LTE) and WiFi interfaces in analyzing the power consumption both from the infrastructure and user device perspectives. The results indicate that the number of active interfaces should be minimized.

This paper is regarding design and program an Micro-controller Arduino Uno board by using Arduino software to work as a photo-sensor(Active) single axial solar tracker system(SASTS). A solar panel, two photo-resistors (LDR) in two sides (north/south) of the photo-voltaic(PV) and a servo motor are connected to the Uno board, which is running a code that prepared by Arduino software IDE in advanced then it works as a tracking system. Here, the LDRs send the signal of presence or absence of the light to the board and based on that sent signal the Uno reflects a new signal to the servo motor to rotate and finds the light source. Lastly, the photo-sensor single axis tracker is made while Continuously, the system tries to face the panel to the sun and whilst changing the irradiance intensity it starts searching to find the angle of highest irradiance. Based on results that are extracted from the data, the tracker system significantly boosts the output efficiency of the solar panel. By using the Micro-controller Uno board, LDRs, servo motor and special designed mechanical base, the tracking system is constructed, based on acquired data the influence of the STS on the increasing the solar panel efficiency is more obvious. Significantly, the tracker system rises the efficiency of the PV .

IoT system becomes hot topic nowadays for smart home, IoT helps devices to communicate together without human intervention inside home, so it is offering many challenges. A new smart home IoT platform powered using electromagnetic energy harvesting is proposed in this paper. It contains a high gain transmitted antenna array and efficient circular polarized array rectenna system to harvest enough power from any direction to increase life time of the batteries used in IoT system. Optimized energy consumption, the software with adopting the Zigbee protocol of the sensor node and low power microcontroller are used to operate in lower power modes. The proposed system has an 84.6 days lifetime which is approximately 10 times the lifetime for similar system. On the other hand, the proposed power management circuit operated at 0.3 V DC to boost the voltage to ~3.7V from radio frequency energy harvesting and manage battery level to increase the batteries lifetime. A predictive indoor environment monitoring system is designed based on a novel hybrid system to provide a non-static plan, approve energy consumption and avoiding failure of sensor nodes in smart home.

This study aims to suggest a basis for the selection of technologies for developing high-performance buildings to reduce energy consumptions and greenhouse gas emissions. Energy-saving technologies comprising of 15 cases were categorized into passive, active, and renewable energy systems. EnergyPlus v8.8 was used to analyze the contribution of each technology in reducing the primary energy consumptions and CO₂ emissions in the Korean climate. The primary energy consumptions of the base model were 464.1 and 485.1 kWh/m²a in the Incheon and Jeju, respectively, and the CO₂ emissions were 83.4 and 87.4 kgCO₂/m²a, respectively. Each technology (cases 1–15) provided different energy-saving contributions in the Korean climate depending on their characteristics. The heating, cooling, and other energy-saving contributions of each technology indicate that their saving rates can be used when selecting suitable technologies during the cooling and heating seasons. Case 15 (active chilled beam with dedicated outdoor air system + ground source heat pump) showed the highest energy saving rate. In case 15, the Incheon and Jeju models were reduced by 189.4 (59.2%) and 206.2 kWh/m²a (57.4%) compared to the base case, respectively, and the CO₂ emissions were reduced by up to 32.7 (60.8%) and 35.6 kgCO₂/m²a (59.3%), respectively.

From the linear Nash-Green fluctuations of background metric, we present the perturbation equations in an embedded four space-time. In the context of a five-dimensional bulk, we show that the perturbations are only propagated by the gravitational tensorial field equation. In a Newtonian conformal gauge, we study the matter density evolution in sub-horizon regime and on how such scale may be affected by the extrinsic curvature. We use the "extended Gold 2018'' growth dataset with 25 datapoints and the best fit Planck2018/LambdaCDM parameters. Hence, we determine the evolution equation for the density growth delta(a) as a result from the embedded equations of the background geometry. By using solar constraints, we analyse the evolution of the effective Newtonian constant G_eff and showing that applying Taylor expansion to G_eff (a) under the constraint of time-derivative of G_eff(0)=G at a= 1 in matter domination era, we get an agreement with Big Bang Nucleosynthesis (BBN) and also an alleviation of the 3-sigma tension to 1-sigma contour between (sigma8-Omega_m) of the observations from Cosmic Microwave Background (CMB) and Large Scale Structure (LSS) probes.

In order to meet the national energy saving goals set in the Vietnam National Energy Efficiency Program in the period of 2019 – 2030 (VNEEP), the Vietnamese government has adopted a series solutions and policies to improve energy efficiency. The Vietnam’s 63 provinces will be as main actor for the national achievement in energy efficiency. Thus, understanding the province’s potentiality of energy efficiency is useful for the harmonious and sustainable development between the economy and energy systems. In this study, provincial and national data from General Statistic Office are analyzed in terms of the energy efficiency levels. With the trends of economic development and energy consumption in both national and regional levels, the Lorenz curve between Vietnamese energy consumption and GDP is investigated. The Lorenz coefficient shows the energy allocation is nether reasonable nor balanced. By using clustering method, the 63 provinces of Vietnam clustered into 7 groups that the provinces in the cluster has the similar indexes of energy efficiency i.e. ability, responsibility, potential and difficulty. The energy consumption and GDP are predicted in the period of 2019 – 2025. Based on the difference of GDP development and energy consumption levels, the target of energy efficiency for each province through clustering is set. The results show that 33 provinces included in the cluster 1, 2, 3, 4 and 6 are heavy contribution. Among them, the provinces in the cluster 2 and 3 need to focus on the industry sector in their energy saving policy. The cluster 7 included the under-developed provinces can learn development’s experiences of the provinces in the cluster 1, 2, 3 and 4 to find the best way of their future development.

Keywords: Energy harvesting, Hybrid, Medical Wearable Sensor Nodes, Health Monitoring, Power Management

In recent years, the application of Indoor Positioning Systems (IPS) has experienced a significant increase in demand, with the aging of the world’s population and their changing lifestyles. While outdoor positioning systems, such as the Global Positioning System (GPS), have significantly advanced over the years, indoor positioning has been restrained by the limitations of the employed technologies. This paper presents a hybrid wireless positioning system able to locate wearables indoor accurately. It is based on the Wi-Fi and Bluetooth technologies, by using trilateration to determine the position of Bluetooth low energy (BLE) wearable devices with an accuracy of up to 1.8 meters. A graphical user interface (GUI) was used to illustrate the performance of the proposed systems, by allowing users to visualize the captured data in two dimensions and three- dimensions in real-time.

We present a method to turn results of model-based optimisations into resilient and comprehensible control strategies. Our approach is to define priority lists for all available technologies in a district energy system. Using linear discriminant analysis and the results of the optimisations, these are then assigned to discrete time steps using a set of possible steering parameters. In contrast to the model-based optimisations, the deduced control strategies do not need perfect foresight but solely rely on data about the present. Our result indicate that the results of the control strategies obtained using the proposed method are comparable to the results of the linear optimisations, in our case in terms of emissions and prices.

The transition of the energy system to renewable sources means the cheap energy storage in fossil fuels must be replaced by other options. A large part of the demand for useful energy is heat and cold, often produced from electric energy by a resistance heater, compression heat pump or cooler. The question is then to store the initial electric energy by electric energy storage (EES) or the useful energy by thermal energy storage (TES). In a desktop study both options were compared, by the choice made in existing applications, and also generally analyzing current technology data. For the latter, cost, round-trip efficiencies, life cycles and life time of EES, specifically for batteries, and of TES, specifically for hot and cold water, ice and other PCM were collected. Applications studied are heating and cooling in buildings and in industry. Application-typical conversion efficiencies were also collected and taken into account. The results show that in many existing installations TES, incl. by PCM, is already preferred, and that TES is advantageous in most investigated applications economically, in addition to technical advantages. Thus, TES has a large potential in the transition of the energy system to stabilize the electricity grid by demand side management.

The scientific community has shown considerable interest in Industry 4.0 due to its capacity to revolutionise the manufacturing sector through digitalisation and data-driven decision-making. However, the actual implementation of Industry 4.0 within complex industrial settings presents obstacles that are typically beyond the scope of mainstream research articles. In this paper, a comprehensive case-study detailing our collaborative partnership with a leading medical device manufacturer is presented. The study traces their evolution from a state of limited digitalisation to the development of a digital intelligence platform that leverages data and machine learning models to enhance operations across a wide range of critical machines and assets. The main business objective was to enhance the energy efficiency of the manufacturing process, thereby improving its sustainability measures while also saving costs. The project encompasses energy modelling and analytics, Fault Detection and Diagnostics (FDD), renewable energy integration and advanced visualisation tools. Together, these components enable informed decision making in the context of energy efficiency.

The shortage of precooling equipment in litchi producing regions could lead to a high loss rate, poor quality of litchis. It is urgent to develop a portable precooling device for litchi producing regions. In this study, a novel spray hydrocooler with thermal energy storage (TES) were designed, fabricated, and tested. A simple mathematical model of TES capacity, ice coil thermal resistance and refrigeration system was employed to determine hydrocooler parameters. Then designed the structure of the spray hydrocooler. Maximum charging test was implemented with full TES capacity and litchi spray hydrocooling experiments were carried out at different charging times, spray flow rate, and litchi load with one-third TES capacity. Results showed that: (1) the spray hydrocooler allows for the rapid and effective precooling of litchis; (2) the hydrocooler can precool 299 kg litchis with one-third TES storage, meet the precooling requirements; (3) the effective TES capacity achieved 1.25×108 J at the maximum TES capacity of the hydrocooler, while the energy efficiency ratio (EER) is 2; (4) the precooling capacity was maximum and the average power consumption was minimum when the litchi load was 23 kg and the spray flow rate was 30 L min-1. Longer charging time is the most important factor in increasing precooling capacity and reducing average power consumption.

With the increased use of laterite nickel ore, the impact of high Al2O3 slag on blast furnace smelting has gradually increased. In this paper, the effects of slag basicity and Al2O3 content on slag viscosity and enthalpy change under constant temperature conditions was investigated. The changes in slag structure were analyzed by activation energy and Fourier Transform Infrared (FT-IR) spectroscopy. The relationship between slag components and slag temperature and viscosity when slag heat is reduced was investigated. The results showed that the viscosity first slightly decreased and then significantly increased with increasing basicity at constant temperature. With the addition of Al2O3 content, the viscosity of the slag increases. The activation energy increases with increasing slag basicity and Al2O3. With increasing basicity, the [SiO4]4- tetrahedral unit trough depth becomes shallow, the [AlO4]5- asymmetric stretching band migrates to lower wave numbers, and the slag structure depolymerizes. With the increase of Al2O3 content, the trough of [SiO4]4- tetrahedra deepens and the center of the symmetric stretching band moves to a higher wave number. The [AlO4]5- asymmetric stretching band becomes obvious, indicating the complexity of the slag structure. When the heat decreases, the slag temperature increases as the basicity increases, and the slag thermal stability is better at the basicity of 0.95-1.05. As the Al2O3 content increases, the thermal stability of the slag becomes worse.

Since the energy sector is the main source of greenhouse gases, it has the highest potential for improvement. Improvements can be achieved by generating energy from renewable sources. Combined with thermal energy storage, concentrating solar power plants represent a promising technology for dispatchable renewable energy, ensuring a stable energy supply even in remote areas without contributing to greenhouse gas emissions during operation. However, it is important to note that greenhouse gases and other polluting emissions may occur during the manufacturing process of concentrating solar power plant components. This work analyses the design of the receiver to produce thermal energy for the existing solar dish CSP plant at the Energy Center of the Politecnico di Torino. The objective of this plant is to produce hot water for a small case study. Considering the average solar irradiance for Turin equal to 800 W/m2, the surface heat flux was obtained from the first part of the analysis, which was used to obtain the maximum internal temperature in the receiver equal to 873.7 °C. The maximum temperature obtained was a constraint for the selection of the material for the solar receiver. Of the various possibilities, copper was chosen. In the second part of the work, a Life Cycle Assessment was carried out to compare the emissions generated during the production of the main components of the CSP plant with the emissions generated by the methane-fuelled water heater that produces the same amount of water as the CSP plant. It can be concluded that the manufacture of the main components of the CSP plant results in lower greenhouse gas emissions than the operational phase of a conventional natural gas-fired water heater (1.6 kg CO2/day).

This study quantified effluents generated during processing in three industry types, estimated the energy potential from the quantified effluents in form of biogas generation, and determined the economic viability of the biogas recovered. Data were procured from relevant scientific publications to quantify the effluents generated from the production processes in the industry types examined using industrial process calculations. The effluent data generated was used on the 2-module biogas energy recovery model to estimate the bioenergy recovery potential within it. Economic and financial analysis was based on cash flow comparison of all costs and benefits resulting from its activities. The effluents generated average daily biogas of 2559 Nm³/gVS, having a daily potential combined heat and power of 0.52 GWh and 0.11 GWh respectively. The Life Cycle Analysis and cost-benefit analysis show the quantity of avoided emissions from using the effluents to generate heat and power for processes, and also the profitability of the approach. Conclusively, the study shows the use of biomass effluents to generate biogas for CHP is a viable one based on the technologies of a reciprocating engine, gas turbine, microturbine, and fuel cell. However, it is recommended that the theoretical estimation be validated using a field-scale project.

With the year 2020, the world faced a new threat that affects all areas of life, negatively affects production in all areas, and paralyzes social life. The measures and restrictions taken by the country's governments to prevent the epidemic from spreading rapidly in the society with the effect of the Covid-19 virus, which first appeared in China and spread all over the world, brought a new lifestyle. Covid-19 has been much the impact on electricity use and electricity production in the period in Turkey as in other countries. There was a sharp decline in commercial and industrial electricity use. The coronavirus effect has also been reflected in the electricity demand and the consumption amount has undergone a great negative change. Due to the enactment of measures against the new type of coronavirus (COVID-19) epidemic and the partial or full-time curfews, electricity consumption was moved to homes, supermarkets, and hospitals in April 2020 from places where mass consumption is intense, such as industry, workplaces, and educational institutions. In this study, Covid-19 period, the first cases were examined electricity production and consumption in Turkey as of the date it is seen throughout, in comparison with electricity consumption data in the same month of the previous years corresponding to this period, the effects on electricity generation and consumption habits of this period were examined.

The high consumption of firewood in Honduras requires the search for alternatives that reduce its negative effects on health, economy, and the environment. One of these alternatives has been the promotion of improved cooking stoves, which achieve a large reduction in firewood consumption. This paper shows a cost-benefit analysis for an improved cooking stove adoption strategy for Honduras. The methodology uses the Long-range Energy Alternatives Planning System, LEAP, a tool globally used in the analysis and formulation of energy policies and strategies. The energy model considers the demand for firewood as well as the gradual introduction of improved cooking stoves, according to premises of a National Strategy. Hence, it is demonstrated that the costs of implementing this adoption strategy are lower than the costs of not implementing it, taking into consideration various scenarios up to and including the year 2030.

In recent years, unquestionable warnings like the negative impacts of CO2 emissions, the necessity of utilizing sustainable energy sources, and the rising demand for municipal electrification have been issued. In this study, by incorporating two significant assumptions, such as electricity production in close proximity to the business location and only renewable energy resource usage, a modest off-grid hybrid energy system is designed. To construct the system, a number of elements such as wind generators (WG), photovoltaic arrays (PV), battery banks, and bi-directional converters are taken into account. Moreover, a real case in Malmö, Sweden, is considered. To optimize the system, a bi-objective problem is developed, and it is solved by proposing a particle swarm optimization (PSO) approach to provide the load requirements (with a maximum allowance of 0.1% unmet) for a nearby supermarket (approximately 1000 m2). Moreover, to verify the obtained results, the developed system is simulated using HOMER Pro software, and the results are compared and discussed. The contribution of this study is to provide off-grid or local clients around the world with a dependable and affordable option by minimizing both the baseline cost of energy and the net current expenditure in the desired system. The best-obtained results by the proposed PSO offered 160 PVs, 5 WGs, and 350 batteries, respectively, while the best solution found by the simulation method was using 384 PVs, 5 WGs, and 189 batteries for the considered off-grid system.

Intended for the high voltage gain and wide-range operation of DC/DC converters for photovoltaic energy storage systems, a topology for four-phase interleaved DC/DC converters for photovoltaic power generation is proposed. This topology increases output voltage for output in series, and reduces the input current ripple by paralleling the input. Compared with traditional boost converter topology, the proposed topology reduces the output current and output voltage ripple, reduces the stress of the switching device, and reduces the withstanding voltage of the output capacitor under the premise of ensuring the boost ratio. Experimental results show that the maximum efficiency of the converter reaches 95.37%. Compared with traditional boost converters, the proposed converter offers obvious advantages in efficiency under the conditions that the output voltage and load are variable.

Infectious disease like COVID-19 will have a great impact on human society. An effective prevention and control measure is to quickly isolate the source and reduce the population’s exposure to the infection. Therefore, it is very important to quickly trace and identify the virus carrier and its close contacts in order to effectively suppressing transmission. This article provides a method, system and storage medium for locating the source of infection based on big data. We adopt the method of combining Bluetooth and GPS positioning to track the action trajectory of each individual. The method stores the close contact and location information locally and update on the cloud platform for an appropriate period of time. The method and system can provide personal risk levels and regional risk levels through related algorithms. When entering a high-risk area or if the personal risk level within the Bluetooth interconnection range is greater than the set threshold, an alarm function is provided. We can also generate reports on the spread of the epidemic over a period of time. As a result, the system can quickly locate the source of infection and close contacts, providing a reference for quick and highly efficient epidemic prevention and control.

The utilization of fuel cells (FC) in automotive technology has experienced significant growth in recent years. Fuel cell hybrid electric vehicles (FCHEVs) are powered by a combination of fuel cells, batteries, or/and ultracapacitors (UCs). By integrating power converters with these power sources, the FCHEV system can overcome the limitations of using them separately. The performance of an FCHEV is influenced by the efficiency of the power electronics converter controller, as well as the technical efficiency of the power sources. FCHEVs need intricate energy management systems (EMSs) to function effectively. Poor EMS can lead to low efficiency and accelerated fuel cell and battery degradation. The literature discussed various types of EMSs, such as equivalent consumption minimization strategy, classical PI controller, fuzzy logic controller, and Mutative Fuzzy Logic Controller (MFLC). However, comparing different EMSs can be challenging due to the varying vehicle and system parameters, which might lead to false claims being made regarding system performance. This research aims to categorize and discuss the various topologies of FCHEVs, highlighting their pros and cons, and comparing several EMSs based on performance metrics such as State of Charge (SOC) and FC deterioration.

The purpose of this paper is to summarize and share the field experiment results of KEPCO's project consortium to create a TSO-DSO-DERA interaction scheme. The field experiment was conducted based on the prequalification algorithm proposed in the previous research from the same consortium and was designed to verify the validity of the algorithm under realistic grid conditions. In addition, during the course of the field experiment, it was found that points that were missed or not given much importance in the existing prequalification algorithm could affect the completeness of the overall system, and then practical improvements were made to improve it. The demonstration results confirm that the proposed algorithm is effective in real-world grid environments and can help DSOs ensure the reliability of the distribution system while supporting DERA's participation in the wholesale market using the proposed prequalification scheme.

This paper aims at presenting an energy management strategy (EMS) based upon optimal control theory for a battery-supercapacitor hybrid power system. The hybrid power system consists of a Lithium-ion battery and a supercapacitor with associated bidirectional DC/DC converters. The proposed EMS aims at computing adaptive gains using salp swarm algorithm and load following control technique to assign the power reference for both the supercapacitor and the battery while achieving optimal performance and stable voltage. The DC-DC converter model is derived utilizing the first-principles method and compute the required gains to achieve the desired power. The fact that the developed algorithm takes disturbances into account increases the power ele-ments’ life expectancies and supplies the power system with the required power

The assessment of photovoltaic devices, which convert light energy into electricity, becomes significantly relevant due to the aspiration to reduce pollution on a global scale. In this context, the pursuit of optimizing the efficiency in converting light energy into electrical energy involves exhaustive studies and structural analyses of solar cells, all directed toward achieving this goal. This study introduces a research proposal aimed at analyzing the losses associated with series resistance (Rs). The analysis takes into account each component comprising this resistance, pro-posing a network of resistances that precisely models each of these elements. The aforementioned research focused on simple-structured crystalline silicon cells. During this investigation, the junction depth (xj) of n-p materials was varied with the aim of achieving efficiencies in the range of 12%. However, in the pursuit of this desired efficiency, a significant impact on series resistance was observed when analyzing the I-V curves of the cells obtained in each manufacturing process.

Societies around the world face serious energy problems related to the consumption of fossil fuels and the emission of dangerous radiation. To solve these problems, a new superconductor exhibiting a critical temperature higher than room temperature has been pursued but not achieved. This paper proposes a new energy generation system based on a circuit approach. Secondary to this process, a new type of superconductivity without refrigeration is demonstrated. In our previous paper [1], this system was proposed, but it did not describe the underlying theory in detail and did not mention an actual method to generate energy from the system. The present paper describes the theory of the existence of divergent current density and new superconductivity with no refrigeration. Moreover, the present paper proposes a method for extracting energy from the system by employing a voltage-controlled current source (i.e., a voltage–current converting method).The principle of the system is based on a circuit of two loops and independent current sources. First, the two electric loops are prepared, each with 4 diodes, where the diodes are oriented in the same direction within each loop, but their direction is opposite from loop to loop; four independent current sources connect the loops. In this circuit system, current is added iteratively as it flows along the loop according to Kirchhoff’s circuit law. As a result, a large current and electric potential are present along the loop. To confirm that this system works properly, it is necessary to demonstrate the presence of divergent currents in the transient state, and to do this, the present paper employs the Dirac equation and Lorentz conservation. Electric circuit software is employed to demonstrate that the presented method generates energy actually from our system.Our results confirm the presence of divergent current at a connected point of an independent current source in the transient state. Moreover, in the steady state, the theory demonstrates the Meissner effect (i.e., a London equation) and a new type of macroscopic wave function and condensation. For an initial small input current of 0.1 μA, the simulation reveals a large generating current of 7 kA and electric power of 10¹¹ W, which is much larger than unit of power from an average thermal power station; moreover, the system presents with superconducting electrical transport conditions.The present study is significant because it demonstrates theoretically the existence of divergent current density and a new type of superconductivity requiring no refrigeration. Secondly, the simulations show the generation of a large energy density that can be obtained in a small laboratory room with minimal cost.

We present a new method for assessing the strength of fuzzy rules with respect to a dataset, based on the measures of the greatest energy and smallest entropy of a fuzzy relation. Considering a fuzzy automaton (relation) in which A is the input fuzzy set and B the output fuzzy set, the fuzzy relation R1 with greatest energy provides information about the greatest strength of the input-output and the fuzzy relation R2 with the smallest entropy provides information about uncertainty of the relationship input-output. We consider a new index of the fuzziness of the input-output based over R1 and R2. In our method this index is calculated for each pair of input and output fuzzy sets in a fuzzy rule. A threshold value is set for choosing the most relevant fuzzy rules with respect to the data.

We analyzed the peak spring tidal current speeds, annual mean tidal power densities (TPD) and annual energy production (AEP) obtained from experiment 06.1, referred as the "HYCOM model" throughout, of the three dimensional (3D), global model HYCOM in an area covering the Baja California Pacific and the Gulf of California. The HYCOM model is forced with astronomical tides and surface winds alone, and therefore is particularly suitable to assess the tidal current and wind-driven current contribution to in-stream energy resources. We find two areas within the Gulf of California, one in the Great Island Region and one in the Upper Gulf of California, where peak spring tidal flows reach speeds of 1.1 meters per second. Second to fifth-generation tidal stream devices would be suitable for deployment in these two areas, which are very similar in terms of tidal in-stream energy resources. However, they are also very different in terms of sediment type and range in water depth, posing different challenges for in-stream technologies. The highest mean TPD value when excluding TPDs equal or less than 50 W/m² (corresponding to the minimum velocity threshold for energy production) is of 172.8 W/m², and is found near the town of San Felipe, at (lat lon) = (31.006 -114.64); here energy would be produced during 39.00% of the time. Finally, wind-driven currents contribute very little to the mean TPD and the total AEP. Therefore, the device, the grid, and any energy storage plans need to take into account the periodic tidal current fluctuations, for optimal exploitation of the resources.

Energy resources are important sources of social and economic development, human survival and security. However, energy resources are objective and scarce, especially the fossil energy, such as coal, oil, natural gas, etc. Human survival environment is increasingly damaged, and the condition of energy is also gradually becoming deficient, so it is necessary to develop new energy resources to meet the increasing demand of material civilization. Solar energy can meet the needs of human development in the future as a kind of clean resource and it has been concerned by all countries in the world. We analyzed the effectiveness of subsidies to the PV industry of both the price and R&D by the spatial econometric model. In some region, the production capacity of photovoltaic industry has shown a significant spatial agglomeration situation in China since 2012. At the same time, benchmarking price and R&D subsidies played a positive incentive to the photovoltaic industry production capacity. It is a certain degree of inverse correlation between the scale of policy subsidies and the resource endowment of solar resources. Therefore, the countermeasures should be considered from the aspects of institutions, industry, technology and public financial policies.

Buildings can play an important role in reducing GHG emissions through increased energy efficiency. The European Commission issued a proposal in 2021 suggesting that all new buildings should be “zero-emission Buildings” (ZEB), aiming at a zero GHG emission building stock by 2050.The extent to which ZEB can contribute to reduced GHG emissions, however, varies between countries, due to different energy systems. It is also important to consider other environmental effects to avoid that climate benefits come with unintended consequences.Here, we explore the life-cycle environmental performance for a ZEB in a case where electricity and heating is largely fossil-free. The assessment concentrates on i) environmental impact of the use stage in relation to the product stage, ii) the interrelation between different energy sources, with attention on household electricity, and iii) the performance for more impact categories than primary energy use and climate change. While our results generally support the use of ZEBs from an environmental perspective, they also show that the climate benefit in this setting is marginal. However, given that energy systems are connected and energy savings in one place can reduce the demand for fossil energy elsewhere, the climate benefit of ZEBs is likely underestimated. Besides methdological implications for future studies, this indicates that current EU policy is promising, as incentives for implementation of ZEBs is unaffected by domestic effects.

Two-wheeler vehicles are the most significant mode of transportation for Kenyans in both rural and urban regions thereby contributing to local air pollution, and greenhouse gas emissions (GHG). The transition to electric two-wheeler vehicles can make a significant contribution to reducing GHG and improving the socio-economic lives of people living in rural Kenya. Re-newable energy systems can considerably contribute to the charging of electric two-wheeled vehicles, thus leading to the reduction of carbon emissions and the expansion of renewable energy penetration in rural Kenya. Therefore, this paper focuses on integrating and modelling electric two-wheeled vehicles (e-bikes) into an off-grid photovoltaic Water-Energy Hub located in the Lake Victoria Region of Western Kenya using the Conventional and Renewable Energy Opti-mization (CARNOT) Toolbox in MATLAB / Simulink. Electricity demand data obtained from the Water-Energy Hub was investigated and analysed. Potential solar energy surplus was identified and electric two-wheeler vehicles were integrated based on the surplus. A field measurement investigation on the energy consumption of the electric two-wheeler vehicles based on the rider’s driving behaviour was also carried. The annual electricity demand of 27,267 kWh, photovoltaic (PV) electricity production of 37,785 kWh with an electricity deficit of 370 kWh were obtained from the simulation results. To reduce the electricity deficit, a load optimisation algorithm was de-veloped to optimally integrate the electric 2-wheeler vehicle into the Water-Energy Hub. It was found that using the load optimisation algorithm, the annual electricity deficit was reduced to 1 kWh and the annual electricity demand was increased by 11% (30,767 kWh) which is enough to charge 4 additional electric two-wheeler batteries daily.

A new model predictive control (MPC) algorithm is used to select optimal air conditioning setpoints for a commercial office building, considering variable electricity prices, weather, occupancy and lighting. This algorithm, Cost-Comfort Particle Swarm Optimization (CCPSO), is the first to combine a realistic, smooth representation of occupants’ willingness to pay for thermal comfort with a bottom-up, non-linear model of the building and air conditioning system under control. We find that using a quadratic preference function for temperature can yield solutions that are both more comfortable and lower-cost than previous work that used a ``brick wall'' preference function with no preference for further cooling within an allowed temperature band and infinite aversion to going outside the allowed band. Using historical pricing data for a summer month in Chicago, CCPSO provided a 3\% reduction in costs vs. a ``brick-wall'' MPC approach with similar comfort and 13\% reduction in costs vs. a standard night setback strategy. CCPSO also reduced peak-hours demand by 3\% vs. the ``brick-wall'' strategy and 15\% vs. standard night-setback. At the same time, the CCPSO strategy increased off-peak energy consumption by 15\% vs. the ``brick-wall'' strategy. This may be valuable for power systems integrating large amounts of renewable power, which can otherwise become uneconomic due to saturation of demand during off-peak hours.

The efficiencies of conventional triple organic Rankine cycle (TORC) configurations are restricted by the low critical temperatures of common working fluids (＜320 °C). This paper proposes a high-temperature TORC system. A near-azeotropic mixture biphenyl/diphenyl oxide (BDO), which has stellar track record in the high-temperature ORC applications, is innovatively adopted as the top and middle ORC fluid simultaneously. The top cycle evaporation temperature is up to 400 °C in view of BDO’s high stability. Five conventional organic fluids are chosen for the bottom ORC. Fundamentals of the TORC system are illustrated, and mathematical models are built. Thermo-economic performance is investigated. The results hint that the optimal thermodynamic property is achieved on the use of benzene as the bottom fluid. The maximum thermal and exergy efficiencies are respectively 40.86% and 74.14%. The largest irreversible loss occurs inside the heat exchanger coupling the middle and bottom ORCs, accounting for above 30% of the total entropy generation. The levelized energy cost (LEC) is 0.0284 $/kWh. Given the same heat source condition, the TORC system can boost efficiency by 1.02% and drive down LEC by 0.0024 $/kWh compared with a BDO mixture-based cascade ORC.

The global transport sector of the world economy contributes about 15% of the Greenhouse Gas (GHGs) emissions in the world today. The University of Saskatchewan has pursued the green energy transition over the years. They have spearheaded diverse sustainability projects and agendas, due to the importance of curbing climate change and advancing sustainability. The transport system in the university campus is one area of focus where the Sustainability Office plans to introduce some innovations, as a way of curbing GHG emissions while also advancing sustainability practice in the university campus. The study carried out an economic benefit analysis on the campus fleet (consisting of 91 ICE vehicles) to determine if it is economically or financially feasible to transition from Internal Combustion Engine (ICE) or PVs (Petrol Vehicles) to Electric Vehicles (EVs). The analysis used RETScreen Expert software for analyzing renewable energy technology projects. The variables of Payback Period (PBP), cash flow projections, savings made from transitioning (fuel cost savings and energy cost savings), Benefit-Cost-ratio, GHG emission reduction potential, etc. were analyzed. The findings revealed that the GHG emission from the campus fleet will be reduced by 100% (this will result in the removal of about 298.1 tCO₂ from the environment). Also, the fleet manager will save approximately $129,049 (88.9%) in fuel costs. Apart from these, the return on investment will be achieved in year 5 (all things being equal), but can be reduced to year 2 if the vehicles are put into constant and active use (eliminating most idle times. Also, the Sustainability Office will be making a GHG reduction revenue of $14,906.

This paper describes research on a unique propulsion system design for a low-speed Biomimetic Unmanned Underwater Vehicle (BUUV). It is biomimetic in the sense that it mimics the movement of aquatic organisms. The undulating propulsion system has numerous advantages over the rotary impeller and is becoming more popular in underwater robotics. The analysis of an artificial seal’s propulsion system with two tail fins is described here. The contrast between the previous undulating propulsion system and the new one is detailed using mathematical analysis and experimental data. The experimental comparison was carried out on a laboratory test stand equipped with specialist sensor equipment to determine the energy efficiency of various types of propulsion systems. Due to a patent procedure, the innovative propulsion system presented in this work has never been published previously. The fins have extra joints, which is the subject of patent claims. The extra joint is intended to improve energy efficiency and reduce fatigue wear on the fins.

The environmental impact and associated health issues have been seen as a significant global challenge. Efforts have been made to make solar cookers efficient to reduce the health risk and environmental impact of traditional cooking energy supplies used in rural areas. The solar cookers effectiveness for cooking purposes must be assessed in a specific area before installation. In essence, this paper assesses the experimental efficiency of German Scheffler, small mirror pieces, and aluminum foil based solar cookers. The solar cookers performances are evaluated at international standards by analyzing the figure of merits such as standard cooking power, sensible heating time, and exergy efficiency by using 1.7652 kg water and 1-liter oil as a heating material. The regression analysis is also performed to observe experimental data compliance with regression line. The time required to attain a water temperature of 95˚C by German Scheffler and small mirror pieces is 25 min and 1 hour with their exergy efficiency of 48.51% and 19.16% respectively, while the aluminum foil solar cooker achieves maximum water temperature of 74˚C within 2 hours and 5 minutes with 13.47% exergy efficiency. Similarly, the highest oil temperature of 275˚C is observed for the German Scheffler solar cooker. From experimental and regression results, it is revealed that German Scheffler possesses more cooking power relative to other solar cookers and their performances are highly dependent on following factors such as solar radiations, ambient temperature, environment (dust particles concentration and wind speed), radiation reflective material, aperture area, and heat losses respectively.

Many buildings built before the energy performance regulations are in a situation of thermal discomfort and energy inefficiency. The creation of intelligent environments advances towards new opportunities, based on real-time monitoring and on the development of sensors and technologies. Furthermore, the standards for building automation and electronic systems enable interoperability and interconnection between control devices and systems. The application of soft computing has significantly improved the energy efficiency, however, requires prior assessment to design the automation functions. Temperature, humidity, air quality, occupancy and energy consumption are the most common measured parameters, but the relationship with other operational variables such as occupancy or some building states remains as a research challenge. This article presents a methodology to develop the automatization of an existing large public building. The methodology consists of three stages: 1. Assessment and diagnosis to set appropriate actions using EN ISO 52120-1. 2. EN 50090 for open communication networks, and EN ISO 52120-1 to assign the technical building management. 3. System control deploying of low-cost and low-consumption input and output devices. It has been proved that it is possible to effectively automate an obsolete building with a low cost, open source system that can be easily applied in other buildings.

The development of technology that combines supercapacitors and lithium-ion batteries by externally connecting them in parallel is ongoing. This study examines the correlation between the volume ratio and electrical characteristics of a cell made by internally connecting a battery capacitor with Li4Ti5O12 as the anode active material and a supercapacitor in parallel. It was found that increasing the volume occupied by the battery capacitor in the cell led to increased cell energy and resistance, resulting in decreased output characteristics. Conversely, increasing the volume occupied by the supercapacitor in the cell led to a decrease in the IR drop during discharge and cell temperature when evaluating cycle characteristics with a current of 20C. The study also examined the behavior of the current distributed during the charging and discharging process based on the volume ratio of the supercapacitor and the battery capacitor. Analyzing the correlation between the volume ratio and electrical characteristics of supercapacitors and battery capacitors could potentially lead to the development of a new type of energy storage device.

The complexity of Mixed-Integer Linear Programs (MILPs) increases with the number of nodes in energy system models. An increasing complexity constitutes a high computational load that can limit the scale of the energy system model. Especially in microgrid optimisation problems with multiple buildings and energy systems with a number of rival supply, distribution and storage technologies, methods are sought to reduce this complexity. In this paper, we present a new 2-Level Approach to MILP energy system models that determine the system design through a combination of continuous and discrete decisions. On the first level, data reduction methods are used to determine the discrete design decisions in a simplified solution space. Those decisions are then fixed, and on the second level the full dataset is used to extract the exact scaling of the chosen technologies. The performance of the new 2-Level Approach is evaluated for a case study of an urban energy system with six buildings and an island system based on a high share of renewable energy technologies. The results of the studies show a high accuracy with respect to the total annual costs, chosen system structure, installed capacities and peak load with the 2-Level Approach compared to the results of a single level optimization. The computational load is thereby reduced by more than one order of magnitude, while a significantly higher accuracy is reached in comparison to the common time series aggregation approach.

This paper provides a comprehensive overview of recent advancements in autonomous electric vehicle (AEV) within the specified region. It elaborates on the progress and comparative analysis of diverse subsystems, including energy storage, cell balancing for battery systems, vehicle charger layouts, electric vehicle motor mechanisms, and braking systems. Furthermore, this paper showcases several prototype autonomous electric vehicles as conclusive study findings.

The growing integration of renewable energy sources (RES) into the power system causes congestion to occur more frequently. In order to reduce congestion in the short term and to make the utilization of the power system more efficient in the long term, power flow control (PFC) in the transmission system has been proposed. However, exemplary studies show that congestion will increase also in the distribution system if the transmission system is expanded. For this reason, the potential of PFC to reduce congestion in a model of a real 110 kV distribution system is investigated. Several Unified Power Flow Controller (UPFC) devices are optimized in terms of their number and placement in the power system, their size, control parameters, and costs, by using a Parallel Tempering approach as well as a greedy algorithm. Two optimization variants are considered, one reducing the number of degrees of freedom by integrating system knowledge while the other is not. We find that near a critical grid state and disregarding costs, PFC can reduce congestion significantly (99.13 %). When costs of the UPFCs are taken into account, PFC can reduce congestion by 73.2 %. A basic economic analysis of the costs reveals that the usage of UPFCs is profitable. Furthermore, it is found that the reduction of the solution space of the optimization problem leads to better results faster and that, contrary to expectations, the optimization problem is simple to solve. The developed methods allow not only for the determination of the optimal use of UPFCs to minimize congestion, but also to estimate their profitability.

A photovoltaic-thermal (PVT) collector is a solar-based micro-cogeneration system which generates simultaneously heat and power for buildings. The novelty of this paper is to conduct energy and exergy analysis on PVT collector performance under two different European climate conditions. The performance of the PVT collector is compared to a PV panel. Finally, the PVT design is optimized in terms of thermal and electrical exergy efficiencies. The optimized PVT designs are compared to the PV panel performance as well. The main focus is to find out if the PVT is still competitive with the PV panel electrical output, after maximizing its thermal exergy efficiency. The PVT collector is modelled into Matlab/Simulink to evaluate its performance under varying weather conditions. The PV panel is modelled with the CARNOT toolbox library. The optimization is conducted using Matlab gamultiobj-function based on Non-Dominated Sorting Genetic Algorithm-II (NSGA-II). The results indicated 7.7% higher annual energy production in Strasbourg. However, the exergy analysis revealed a better quality of thermal energy in Tampere with 72.9% higher thermal exergy production. The electrical output of the PVT is higher than from the PV during the summer months. The thermal exergy- driven PVT design is still competitive compared to the PV panel electrical output.

The Science-Sustainability poses an interdisciplinary paradox. On the one hand, the science for sustainability has increased in OECD economies in and in China as well as in the US in particular; on the other hand; the sustainability situation has worsened (Co2 emission has risen). On the face value, the adverse correlation shows a paradox. However, without explicating the science-sustainability relationship, it leads to a premature conclusion. In this study, we have drawn on three concrete questions for concrete answers. First, whether and how interdisciplinary sciences—energy science and environmental science—contribute to the sustainability. Second, whether and how the Sino-US inter-institutional analysis varies in the science-sustainability paradox. The empirical analysis from a panel data in the interdisciplinary and inter-institutional context show mixed patterns in three ways. First, the increase in the environmental science shows an improvement in the sustainability; the energy science shows a decline in the sustainability. Second, the Chinese environmental science has a comparative advantage to American environment science for the sustainability development, and the Chinese energy science has a comparative disadvantage to the US in the sustainability development. Third, the environmental science mediates the energy science in the science-sustainability relationships. Standing alone, the increase in the energy science harms sustainability; mediated by environmental science, it benefits sustainability. The study explains the adverse role of energy science in Jevons Paradox. The study also offers some policy paths for further research how capitalisms differently innovate, form strategies, and implement the practice.

Thermal comfort is extremely important in architecture, especially in environments with more people spending longer on studies or intellectual activities. This research describes a case study to investigate university buildings' energy and thermal performance as a part of the ANEEL program. Due to this importance, and the need to save energy in Brazilian public buildings, the ANEEL-the Brazilian Energy Electricity Regulatory Agency, launched 2016 a national program focusing on energy efficiency in public universities around the country. University offices and classrooms require high intellectual effort; thus, environmental comfort is critical for maintaining its users' physical and mental health. This study included a pre-diagnosis of the performance of the envelope, lighting, and air conditioning systems and a survey about the quality of the environments from the users' point of view. The Prescriptive Method of the Brazilian Labeling Program (PBE) for Commercial, Service, and Public Buildings (RTQ-C) assessed the building performance. Statistical analysis was applied to correlate the quality and thermal preference of the users from the PMV/PPD. The results showed a high rate of thermal discomfort in both environments of the studies, even when using air conditioning.

Microgrids (MGs) have evolved as critical components of modern energy distribution networks, providing increased dependability, efficiency, and sustainability. Effective control strategies are essential for optimising MG operation and maintaining stability in the face of changing environmental and load conditions. Traditional rule-based control systems are extensively used due to their interpretability and simplicity. However, these strategies frequently lack the flexibility for complex and changing system dynamics. This paper provides a novel method called hybrid intelligent control for adaptive MG that integrates basic rule-based-control and deep learning techniques, including gated recurrent units (GRU), basic recurrent neural network (RNN) and long short-term memory (LSTM). The main target of this hybrid approach is to improve MG management performance by combining the strengths of basic rule-based systems and deep learning techniques. These deep learning techniques readily enhance and adapt control decisions based on historical data and domain-specific rules, leading to increasing system efficiency, stability, and resilience in adaptive MG. Our results show that the proposed method optimises MG operation, especially under demanding conditions such as variable renewable energy supply and unanticipated load fluctuations. This study investigates special RNN architectures and hyper-parameter optimization techniques with the aim of predicting power consumption and generation within the adaptive MG system. Our promising results show the highest-performing models indicating high accuracy and efficiency in power prediction. The finest-performing model accomplishes an R2 value close to 1, representing a strong correlation between predicted and actual power values.

The interest in renewable energy to replace fossil fuel is increasing as the problem caused by climate change become more severe. Small hydropower (SHP) is evaluated as a resource with high development value because of its high energy density compared to other renewable energy sources. SHP may be an attractive and sustainable power generation environmental perspective because of its potential to be found in small rivers and streams. The power generation potential could be estimated based on the discharge in the river basin. Since the river discharge depends on the climate conditions, the hydropower generation potential changes sensitively according to climate variability. Therefore, it is necessary to analyze the SHP potential in consideration of future climate change. In this study, the future prospect of SHP potential is simulated for the period of 2021 to 2100 considering the climate change in three hydropower plants of Deoksong, Hanseok, and Socheon stations, Korea. As the results, SHP potential for the near future (2021 to 2040) shows a tendency to be increased and the highest increase is 23.4% at the Deoksong SPH plant. Through the result of future prospect, we have shown that hydroelectric power generation capacity or SHP potential will be increased in the future. Therefore, we believe that it is necessary to revitalize the development of SHP in order to expand the use of renewable energy. Also, a methodology presented in this study could be used for the future prospect of the small hydropower potential.

In this paper, modelling, simulation and verification of multi-agent manufacturing system with application of bio-inspired techniques are addressed. To this end, the new solution of abstract architecture for control and coordination decentralized systems - CODESA is suggested. Centralized architecture suffers from various problems, such as rigidity, scalability, low fault-tolerance or very limited flexibility, agility, energy efficiency and productivity. Prime is concrete application of CODESA in manufacturing domain. The undesirable characteristics of emergent behaviour are the problem to achieve optimization and impossibility to predict future states of the system. CODESA-Prime has been tested by simulations for automatic guided vehicle (AGV) systems guided by magnetic tape in Ella Software Platform.

Recent years have seen a rapid uptake in distributed energy resources (DER). Such technologies pose a number of challenges to network operators, which can ultimately limit the amount of rooftop solar photovoltaics (PV) systems that can be connected to a network. The objective of this industry-based research was to determine the potential network effects of forecast levels of customer owned rooftop solar PV on Energy Queensland’s distribution network and formulate functions that can be used to determine such effects without the requirement for detailed network modeling and analysis. In this research, many of Energy Queensland’s distribution feeders were modelled using DIgSILENT PowerFactory and analyzed with forecast levels of solar PV and customer load. Python scripts were used to automate this process and quasi dynamic simulation (QDSL) models were used to represent the dynamic volt-watt and volt-var response of inverters, as mandated by the Australian Standard AS/NZS 4777. In analyzing the results, linear regression was used to form trend equations that represent various network characteristics against the number of PV connections. The trend equations provide a way of approximating network characteristics for other feeders under various levels of customer owned rooftop solar PV without the need for detail modeling.

Ni-Al alloys have good corrosion-resistant properties making them preferable as a material of choice compared to ordinary metals. A good understanding of the phase diagram and thermodynamic properties of the Ni-Al alloy binary system is essential in determining relevant industrial applications of the system. The Ni-Al phase diagram is being reassessed since those found in the literatures are based on very old experimental studies. The phase diagram and thermodynamic properties of the Ni-Al alloy is determined using the Thermo-Calc 2022b software over a temperature range of 200 K to 2000 K and 1 atm of pressure. A total of nineteen fields (including elemental Al and Ni) comprising of five single solid phases, one liquid phase, and twelve double regions was obtained from the equilibrium calculation. The thermodynamic calculation has six invariant reactions comprising of two eutectic reactions (914.83 ± 0.025 K and 1641.80 ± 0.025 K), three peritectic reactions (1123.55 ± 0.025 K, 1400.72 ± 0.025 K and 1642.65 ± 0.025 K), and one peritectoid reaction (913.96 ± 0.025 K). The solubility of Al in Ni is also determined. The Thermo-Calc temperature – composition of the Ni-Al alloy is compared with the existing experimental studies to identify the physical properties of the different thermodynamic properties of the Ni-Al alloy binary system.

Student attendance serves many other important purposes aside from monitoring. In certain universities, the attendance of students in a course is also used as one of the requirements for students to be allowed to sit for the final examination. Traditionally, among most Malaysian Institutions of Higher Learning (IHL), attendance recording is usually done using pen and paper, or uses simple web-based system that is time consuming and difficult for faculty periodic monitoring. To address the identified drawbacks, this research aims to develop a Smart Attendance for Faculty Monitoring System using the Bluetooth Low Energy (BLE) technology to assist faculty in recording, managing and monitoring students’ attendance and class schedules effectively. The system is developed for Android-based devices using an agile methodology consists of iteration and incremental approaches. Thus, to evaluate the effectiveness of the system, a survey was conducted on 140 respondents involving lecturers and students of Kolej Universiti Poly-Tech MARA (KUPTM). Respondents were selected using purposive sampling. The descriptive analysis showed that 87.9% of the respondents strongly agreed that the system is effective in assisting lecturers to record attendance, manage class schedules and student attendance as well as to assist faculty in monitoring students’ absenteeism.

The use of smart grids has enabled a number of planning methods to be developed to optimize energy costs, Peak to Average Ratios (PARs), and consumer satisfaction for load management in industrial, commercial, and domestic sectors. From a technical point of view, achieving optimal outcomes requires Demand Side Management (DSM). In smart grids, utility companies and electric users communicate two-way using digital technology to make a sustainable and economic system. This paper proposes a novel framework within which an Energy Management Controller (EMC) keeps track of each appliance, its operational time, and the costs associated with them. Customers of smart grids are motivated to shift their Off-Peak Hours (OPH) from Peak Hours by presenting incentives in OPH. The metering devices would also save customers costs by preventing load shifting between high- and low-cost periods. In addition, the study proposes the bacterial foraging algorithm and grasshopper optimization algorithm for lessening power price and PAR without compromising user comfort (UC) through appliance planning. The simulation results on a practical test system advocate the high effectiveness and reliable performance of the proposed model.

The utilization of wind energy has become increasingly popular in the United States and many European countries due to its abundant natural source and optimized design. While existing wind turbines are predominantly large-scale and not suitable for standalone or distributed power production, Lubbock County in West Texas offers a diverse range of renewable energy options to meet its energy needs. The region relies heavily on utility-scale wind energy sources to supply power to the Texas Grid, replacing conventional fossil fuel-based systems. Currently, standalone solar PV systems are the preferred choice for renewable energy generation. However, West Texas possesses an ample supply of wind energy that can be harnessed to establish a microgrid and provide standalone power to rural communities. By employing the latest technology and optimizing efficiency, even in low-scale generation, a 6 kW permanent magnet alternator-based distributed wind turbine has been designed. This paper focuses on analyzing the techno-economic aspects of implementing this wind turbine in a real-world scenario, taking into account wind attributes such as velocity and available power at the specific location.

Vernacular architecture constitutes a rich source of information and ancestral knowledge that can become a key resource for sustainable development through its passive design strategies, which effectively respond to local climatic and weather conditions using locally sourced materials for the construction of its supporting structure and enveloping elements, as well as spatial organization and the incorporation of a buffer area (patio) that optimize the use of renewable resources. This qualitative study analyzes a traditional housing typology with a central patio located in the Historic Center of Azogues city, Ecuador, to evaluate its interior thermal comfort through in-situ monitoring in the different building spaces. Using the open-source software Open Studio and EnergyPlus, a simulation model was built to assess the annual thermal performance of the house. Field records were used to verify the effectiveness of the strategies that respond to the climatic conditions of the area. The analysis carried out on the passive strategies used in the selected house with regard to natural ventilation, solar protection, and thermal insulation, which depend on various aspects of the building, such as its location, internal space arrangement, design of openings (doors and windows), among others. The thermal simulations reveal that the traditional house located in the Historic Center of Azogues city is well adapted to the local climate, although interior thermal comfort is not entirely satisfactory.

This paper focused on the finite element analysis of structural system in extreme loading condition. Two different stud shape and thicknesses were analyzed under blast. The stud thickness such as 1.19 mm and 1.5 mm were modelled and analyzed using ABAQUS 6.14. FEM is a tool which predicts the engineering physics of the real structure. To validate the finite element modelling performed by authors, a reference work published by earlier researchers on cold-formed steel stud wall is considered and examined in the present study. The novelty of this study was web corrugation and influence of flange width on stud. The models mimic like an air bag in a car to delay the pressure timing inside the stud wall. The mass of explosive used as 1.56 kg at a standard scaled distance. Time versus displacement was captured out at four locations in the stud wall. One of the objectives is to develop mathematical model to validate the deformation of stud under blast loading. Two mathematical models were validated using Artificial Neural Network (ANN). The results captured in ANN model was error histogram, regression plot, best performance fit and training data. The models were capable of resisting the moderate blast load. The response surface methodology (RSM) was employed to evaluate model performance Regression equations are useful for predicting future trends and outcomes, which is crucial for planning and decision-making. The primary goal of this work is to evaluate cold-formed steel stud walls with varying stud sizes under blast loading using finite element analysis and validated by ANN and RSM.

Recently it was found from Cassini data that the mean recession speed of Titan from Saturn is v = 11.3 ± 2.0 cm/yr which corresponds to a tidal quality factor of Saturn Q ≈ 100 while the standard estimate yields Q ≥ 6 · 10⁴ . It was assumed that such a large speed v is due to a resonance locking mechanism of five inner mid-sized moons of Saturn. In this paper, we show that an essential part of v may come from a local Hubble expansion, where the Hubble-Lemaˆıtre constant H0 recalculated to the Saturn-Titan distance D is 8.15 cm/(yrD). Our hypothesis is based on many other observations showing a slight expansion of the Solar system and also of our Galaxy at a rate comparable with H0. We demonstrate that the large disproportion in estimating the Q factor can be just caused by the local expansion effect. [Accepted for publication in "Gravitation and Cosmology". The paper is to appear in Vol. 28, Issue 2 (2022) of the journal Gravitation and Cosmology.]

The Wind Energy Conversion System (WECS) plays an inevitable role across the world. In particular, the attention for Permanent Magnet Synchronous Generators (PMSGs) connected with wind farm is popular. This paper deals with the literature review that describes the recent advances, progresses and innovatory trends on PMSGs for WECS. Comparison between geared and direct-driven conversion systems and the classification of electrical machines used in WECS are discussed. A detailed analysis on the design aspects considering various topologies of PMSGs are encompassed in the literature. The PMSG design and optimization problems are solved by field computation techniques and optimized by using Soft Computing (SC) techniques .The three-dimensional, finite element software platform for the analysis and design of PMSGs is discussed. This paper also deals with the interdisciplinary modeling, analysis, and optimization of PMSG using Finite Element Analysis (FEM) and SC techniques. Finally, PMSGs are reviewed and compared for further exploration.

Grid energy storage system for PV Applications is connected with three different power sources i.e. PV Array, Battery and the Grid. It is advisable to have Isolation between these three different sources to provide safety for the equipment. The configuration proposed in this paper provides the complete isolation between the three sources. A Power Balancing Control (PBC) for this configuration is proposed to operate the system in three different modes of operation. Control of a dual active bridge (DAB) based battery charger which provides a galvanic isolation between batteries and other sources is explained briefly. Various modes of operation of a Grid energy storage system are also presented in this paper. Hardware-In-Loop (HIL) Simulation is carried out to check the performance of the system and the PBC algorithm. Power circuit (comprises of inverter, dual active bridge based battery charger, grid, PV cell, batteries, contactors and switches) is simulated and the controller hardware and user interface panel are connected as HIL with the simulated power circuit through Real Time Digital Simulator (RTDS). HIL simulation results are presented to explain the control operation, steady state performance in different modes of operation and the dynamic response of the system.

Modeling and assessing the sustainability of machining systems has been considered to be a crucial approach to improving the environmental performance of the machining processes. As the most common machining system, the computer numerical control (CNC) milling system is a typical man-machine cooperative system where the activities of the machine tool and operator generate material and energy consumption. However, the energy consumption of the operator in the CNC milling system has often been ignored in most existing research. Therefore, existing methods fail to provide a comprehensive understanding of the sustainability of the CNC milling system. To fill this gap, an exergy loss assessment method is proposed to investigate the sustainability of the CNC milling system, where the energy consumption of the operator, the energy consumption of the machine tool, and material consumption are taken into consideration. The key performance indexes of the energy consumption of the operator, the energy consumption of the machine tool, the exergy loss, and the specific exergy loss (SEL) are analyzed and modeled. To demonstrate the feasibility of the proposed method, a case study was carried out on a three-axis machining center (XH714D), in which SEL was found to be 88.04J/mm3. The proposed method is effective to assess the sustainability of the CNC milling system, and the established exergy loss models build a good basis for exergy efficiency optimization.

Nuclear technologies have the potential to play a major role in the transition to a global net-zero society. Their primary advantage is the capability to deliver controllable 24/7 energy on demand. However, as a prerequisite for successful worldwide application, significant innovation will be required to create the nuclear systems of the 21st century, the need of the hour. The pros and cons of nuclear are discussed and analysed at different levels – the societal and public recognition as well as the scientific/engineering and economic level – to assure a demand driven development. Based on the analysis of the different challenges a vision for the nuclear system of the 21st century is synthesised consisting of three pillars – unlimited nuclear energy, zero waste nuclear, and accident free nuclear. These three combined visions are then transformed into dedicated and verifiable missions which are discussed in detail regarding challenges and opportunities. In the following a stepwise approach for the development of such a highly innovative nuclear system is described. Essential steps to assure active risk reduction and the delivery of quick progress are derived as answer to the critique on the currently observed extensive construction time and cost overruns on new nuclear plants. The 4-step process consisting of basic studies, experimental zero power reactor, small scale demonstrator, and industrial demonstrator is described. The 4 steps including sub-steps deliver the pathway to a successful implementation of such a ground breaking new nuclear system. The potential sub-steps are discussed with the view not only onto the scientific development challenges, but also as an approach to reduce the regulatory challenges of a novel nuclear technology.

Gwadar is essential for Pakistan's financial stability. The third deep-water port in Pakistan, Gwadar, plays a significant part in trade between the Gulf countries, Africa, China, United Arab Emirates, and Cordillera Administrative Region. However, the load Shedding of 12-16 hours in Gwadar is the most concerning issue. Pakistan imports 70 MW of electricity from Iran. The wind and solar system are already installed but for a limited residential area. In Gwadar, there are enough renewable energy resources that can be utilized for electricity generation. In this context, a Techno and Economic Analysis is performed using the Hybrid Optimization Model for Multiple Energy Resources (HOMER) Pro. Two models are considered for this study. Model-1 includes PV/Wind Turbine/ and Battery while Model-2 consists of PV/Wind Turbine/Converter and Grid. The yearly energy generated by Model-1 and Model-2 is 57.37 GWh and 81.5 GWh, respectively. The levelized cost of electricity (LCOE) for Model-1 and Model-2 is respectively $0.401/kWh and $0.0347/kWh. It is shown that the simple payback of Model-1 is of 6.70 years, and the simple payback of Model-2 is 7.77 years. Due to the high LCOE of Model-1, its payback year is lesser than model-2. All of these facts indicate that Model 2 is the most optimal solution.

In recent decades, greenhouse gas (GHG) emissions have been a critical priority of global environmental policy. The leading cause of the increase in GHG triggering global warming in the atmosphere is the continuously growing demand for universal energy due to population and economic growth. Energy efficiency and reduction of CO2 emissions in highly-energy consuming sectors of Turkey are critical in deciding a low-carbon transition. In this study, the change of energy-related CO2 emissions in Turkey’s energy-intensive four sectors from 1998 to 2017 is analyzed based on the Logarithmic Mean Divisia Index (LMDI) method. It is used to decompose CO2 equivalent emissions changes in these sectors into five driving forces; changes in economic activity, activity mix, energy intensity, energy mix, and emission factors. Analytical results indicate that economic activity is a vital decisive factor in determining the change in CO2 emissions as well as sectoral energy intensity. The activity effect has raised CO2 emissions, while energy intensity has decreased. This method indicates that the impact of the energy intensity could be the first key determinant of GHG emissions. Turkey's efforts to be taken in these sectors in adopting low carbon growth policies and reducing energy-related emissions to tackle climate change are clarified in detail.

A conventional electrical grid mostly depends on the electrical power generated from fossil fuels. However, the pollutants from fossil fuels are the key factors for adverse climate change. Most of the developed countries of the world have already recognized the fact that the energy mix requires to be diversified by incorporating renewable energy. This is especially relevant for many of the member countries of the Organization of Islamic Cooperation (OIC), consisting of 57 countries, whose abundance of fossil fuel reserve indicates that much of their electric power is still generated from fossil fuels. In order to integrate renewable energy sources into the hybrid energy mix, an existing conventional grid needs to undergo drastic changes. Alongside this, the population boom in the OIC member countries has caused higher demand for a steady supply of electricity that the conventional grids have long been struggling to cope with. With a view to solving this multifaceted problem, incorporation of the smart power management schemes is indispensable using a smart electrical grid, where information and communications technology is integrated into its major building blocks. This allows advanced applications of a grid, such as the formation of micro-grids, demand-side management, energy storage, high-tech power electronic converters, etc. As the smart grids are being adopted by many developed countries, it is high time for the OIC member countries to pay due attention to this development, if they have not already done so. This paper explains, with special focus on the OIC member countries, the various smart power management technologies, their operations and applications, and the benefits and challenges. Then it goes on to carry out the Strength-Weakness-Opportunity-Threat with Analytical-Heuristic-Procedure (SWOT-AHP) analysis to evaluate its feasibility of incorporation and the underlying strategies appropriate for its implementation. Furthermore, a Hybrid Multi-Criteria-Decision-Making (MCDM) analysis is performed to evaluate the sequence of the emphasis that should be given on each of the technologies from those available for the smart power management initiative. Finally, the study reinforces the stance by drawing parallels from the UN Sustainable Development Goals (SDG) and highlights the importance of the smart grid in line with the global vision of SDG. This paper aims at assisting the decision-makers in implementing smart power management schemes in the OIC member countries, in particular, and other countries of the world, in general.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

Due to the imbalance between the supply and demand of oxygen, the oxygen system of iron- and steel-making enterprises in China has problems with high oxygen emission and high pressure in the pipelines, resulting in the energy consumption of oxygen production being high. To relieve this problem, using a large-scale iron- and steel-making mill as a case study, the research on demand forecasting and optimal scheduling of the oxygen system was carried out. The ARIMA model and the GABP model are employed to forecast oxygen demand. Based on the forecast results, an optimal scheduling model for the oxygen system was developed to conduct optimal scheduling. The case study shows that based on the oxygen demand forecast and the optimal scheduling, the oxygen emission and the pipeline pressure in the studied iron- and steel-making enterprise can be significantly reduced, thereby achieving considerable energy-saving effects and economic benefits. Specifically, the following conclusions are obtained: (1) For the oxygen demand forecast, the prediction accuracy of the GABP model is better than that of the ARIMA model. The average MAPE of the 12 sets of data of the ARIMA and GABP models are 23.8% and 20.2%, respectively. (2) By comparing the scheduling results and the field data, it is found that after the scheduling, the amount of oxygen emission has decreased by 6.32%, the pipeline pressure has decreased by 0.61%, and the energy consumption of oxygen compression has decreased by 1.6%. Considering both the oxygen emission loss and the energy consumption of oxygen compression, the total power consumption of the oxygen system is reduced by 1.38%, which saves the electricity cost of about 9.03 million RMB per year.

In this paper, the experimental study of heating in 2 h lunch mode of air-conditioned bed system is carried out. The results show that the power consumption of heat conduction heating is only 0.34 kW·h, and the average heat dissipation is 81.3 W, while the power consumption of convection heating is 1.43 kW·h, with an average heat dissipation of 748.7 W. Regardless of power consumption or heat dissipation, convection heating is significantly higher than heat conduction heating, resulting in the room air temperature of the former increased from 12.3 °C to 17.3 °C, while the latter only increased from 14.4 °C to 15.2 °C. The study found that the water temperature of heat conduction heating can meet the thermal comfort needs of the human body in the range of 38~40 °C, while convection heating requires a higher temperature range, In contrast, the grade of hot water required for heat conduction heating is lower. Through the experiment, it is also found that the temperature of convection heating rises fast, but it is easy to appear dry feeling after a long time, while heat conductive heating has a slow temperature rise. there is a cool feeling within 20 min after the heating starts, and then the thermal comfort is better. The air conditioning system in this paper is used for the heating experiment in the winter lunch break mode, compared with convection heating, the overall thermal comfort of heat conduction heating is better and more energy efficient. it is suggested to adopt heat conduction heating mode in the winter heating of this system.

This paper presents the results of aerodynamical performance research focused on maintaining the thermal comfort and increasing the energy efficiency of a typical social housing unit located in a high-density urban area. Bioclimatic design strategies are used to develop a sustainable and economic technology in existing housing clusters in Mexico City. A full-scale prototype, built on campus facilities, was used to study the flow conditions around the design. All scaled prototypes implement similar criterion. Furthermore, a scaled prototype is evaluated within a low speed wind tunnel installation. Additionally, numerical simulations were performed at transient state based on previous physical measurements and historical local climatic conditions to determine preferable modifications.

The formation of the required AC voltage level is currently one of the most important problems. An unstable voltage level can lead to the failure of domestic and industrial equipment, also to the appearance of a lighting equipment flicker effect, which can adversely affect the operating mode. In this regard, the development of AC voltage regulators that perform the function of stabilizers has become relevant. In turn, new topologies should be energy efficient and reliable, this can be achieved by reducing the number of semiconductor elements, which in turn will reduce losses and increase efficiency. In addition to voltage stabilization, AC voltage regulators have found application as soft-start devices for asynchronous motors, and have become competitors to frequency converters. The power level can vary from units to tens of kilowatts where such devices can be used. This paper provides a review of AC voltage regulators, which can be used both as soft starters and AC voltage stabilizers. The analysis of the circuits was carried out and the efficiency was evaluated through their total harmonic distortions (THD), power factor and efficiency coefficient. Experiments were also performed for a number of circuits, where their operating modes were evaluated. Eventually, all circuits were divided into full number of switches with two or more AC switches per phase, with a reduced number of switches, where one AC switch per phase and with low number of switches – with one complementary pair of AC switches for all three phases.

This paper presents a novel theoretical and computational methodology for the generation of an onset turbulent field with prescribed properties in the numerical simulation of an arbitrary viscous flow. The methodology is based on the definition of a suitable distribution of volume force terms in the right–hand side of the Navier–Stokes equations. The distribution is represented by harmonic functions that are randomly variable in time and space. The intensity of the distribution is controlled by a simple PID strategy in order to obtain that the generated turbulent flow matches a prescribed turbulence intensity. A further condition is that a homogeneous isotropic flow is es- tablished downstream of the region where volume force terms are imposed. Although it is general, the proposed methodology is primarily intended for the computational modelling of hydrokinetic turbines in turbulent flows representative of tidal or riverine installations. A first numerical applica- tion is presented by considering the injection of homogeneous and isotropic turbulence with 16% intensity into a uniform unbounded flow. The analysis of statistical properties as auto-correlation, power spectral density, probability density functions, demonstrates that the generated flow tends to achieve satisfactory levels of stationarity and isotropy, whereas the simple control strategy used determines overestimated turbulent intensity levels.

The issue of water and energy crisis have been turned into global matters which need to be tackled jointly. Accordingly, floating solar power plants, in which photovoltaic modules are used on the surface of water infrastructures, has recently been attracting much interest. This system provides some additional advantages over the ground-based system such as conserving the land and the water and increasing the efficiency of the module. This study first reviews the relevant literature comprehensively and then evaluates the potential of using floating solar photovoltaic (FSPV) on some of Iran’s water infrastructures which have experienced a large amount of evaporation every year due to high solar radiation. To this end, the five important dam reservoirs are selected as the representatives of the five important watersheds in Iran, and the advantages of the FSPV plant is analyzed in terms of energy generation, evaporation reduction, economic and environmental aspects considering different coverage percentages of reservoir’s surfaces. Considering Iran's vast potential for solar radiation, and, on the other hand, huge energy demand and critical water situation, results indicated that Iran can effectively harness solar energy through FSPV systems which help conserve the water in addition to support sustainable energy production.

The rate of technical innovation, system interconnection, and advanced communications undoubtedly boost distributed energy networks' efficiency. However, when an additional attack surface is made available, the possibility of an increase in attacks is an unavoidable result. The energy ecosystem's significant variety draws attackers with various goals, making any critical infrastructure a threat, regardless of scale. Outdated technology and other antiquated countermeasures that worked years ago cannot address the complexity of current threats. As a result, robust artificial intelligence cyber-defense solutions are more important than ever. Based on the above challenge, this paper proposes an ensemble transfer learning spiking immune system for adaptive smart grid protection. It is an innovative Artificial Immune System (AIS) that uses a swarm of Evolving Izhikevich Neural Networks (EINN) in an Ensemble architecture, which optimally integrates Transfer Learning methodologies. The effectiveness of the proposed innovative system is demonstrated experimentally in multiple complex scenarios that optimally simulate the modern energy environment. In this way, the proposed system fully automates the strategic security planning of energy networks with computational intelligence methods. It allows the complete control of the digital strategies of the potential infrastructure that frames it, thus contributing to the timely and valid decision-making during cyber-attacks.

Uganda possesses natural rainforests that serve enormous environmental ecosystems and biodiversity services. Moreover, the country is known for its various tropical rainforest hardwoods, birds, and animal species. Over the years, the trend in the natural forest land has declined at an alarming rate; hence need to investigate the possible drivers. The loss of such biodiversity and ecosystems risks desertification and extreme climatic condition. As the world moves towards Zero Deforestation 2030, understanding the determinants of deforestation and forest degradation is paramount. Therefore, the main objective of this study was to understand the impact and relationships between net forest conversion, energy emission, agriculture, and forest production of Roundwood. We used data from FAO for the period 2004-2016. Using the ADF and KPSS test, we checked for the unit root presence in the variables. Also, the study used two different regression models: multiple linear regression and dynamic linear model. To analyze the determinants of deforestation, we used net forest conversion in Uganda. There was 94 % variation in the dependent variable (Net Forest conversion). The outcome of the dynamic linear regression showed that agriculture and energy emission positively impact net forest conversion. Based on our findings, this study recommended the modernization of agriculture by the government of Uganda to stop cutting down the forests on a big scale. Also, the study suggested that the government strictly legislate Roundwood and wood fuels/charcoal and firewood to reduce huge dependency on forests toward Zero-Deforestation by 2030. If well-structured and implemented, government policies could solve the unnecessary over dependency on the rainforest, the heart of the region's climatic conditions.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

The system design for Sustainable manufacturing is to consider both ecological and financial constraints. Manufacturing industry demands to advance in sustainable manufacturing by accounting in environment factors in it. All the factors that affect the environment need to be analyzed so that proper amendments or suggestions can be provided. To favour this, Computer aided life cycle inventory model has been presented for CNC milling and turning processes. Based on utilization of resources and stages, whole machining operation time can be divided into three phases named as process (milling or turning), idle and basic times. As parameters are different for evaluating the process times i.e. depth and width of cut in case of milling and initial and final diameters for turning, two different case studies has been presented one for each milling and turning process. Effect of material choice has been studied for different processes. Highly dense and hard materials takes more time in finishing the job due to low cutting speed and feed rates as compared to that of sot materials. In addition, face milling takes more time and consumes more power as compared to peripheral milling due to more retraction time caused by over travel distance and lower vertical transverse speeds than the horizontal transverse speed used in peripheral retraction process.

The rate constants of elementary processes in the atom-diatom system O(³P)+H₂(v), including the processes of vibrational relaxation and dissociation, were studied using the quasi-classical trajectory method. All calculations were carried out along the ground potential energy surface (PES) ³A′′ that was approximated by a neural network. Approximation data were obtained using ab initio quantum chemistry methods at the extended multi-configuration quasi-degenerate second-order perturbation theory XMCQDPT2 in a basis set limit. The calculated cross sections of the reaction channels are in good agreement with the literature data. A complete set of state-to-state rate constants was obtained for the metathesis reaction, the dissociation and VT relaxation of the H₂ molecule upon collision with an O atom. According to this data Arrhenius approximations over a wide temperature range were obtained for the thermal rate constants of considered processes. Data obtained on the dissociation constants and VT relaxation of vibrationally excited H₂ molecules can be used in constructing kinetic models describing the oxidation of hydrogen at high temperatures or highly nonequilibrium conditions.

Battery/Supercapacitor(SC) current tracking control is a key issue for hybrid energy storage system (HESS) in electric vehicles. An innovative passivity-based L2-gain adaptive control (PBL2AC) based on port-controlled Hamiltonian model with dissipativity (PCHD) for reference current tracking and bus voltage stability in HESS is presented. The developed PCHD model has considered both parameter variations and external disturbances. By using L2-gain disturbance attenuation, the PBL2AC ensures robust reference current tracking and stable bus voltage. Moreover, adaptive mechanism is adopted to estimate the electrical parameters. To validate the proposed control scheme for HESS, simulations and experiments were done and compared with traditional PID and sliding mode control under several typical driving cycles, and results show that the effectiveness of the proposed controller can be confirmed.

The energy transition towards renewable and more decentral power production triggers the need for grid and storage expansion on all voltage levels. Today's power system planning focuses on certain voltage levels or spatial resolutions. In this work we present an open source software tool eGo which is able to optimize grid and storage expansion throughout all voltage levels in a developed top-down approach. System costs are minimized by applying a linear optimal power flow considering the grid infrastructure of the extra-high and high-voltage (380 to 110 kV) level. Hence, the common differentiation of transmission and distribution grid is partly dissolved, integrating the high-voltage level into the optimization problem. Consecutively, optimized curtailment and storage units are allocated in the medium voltage grid in order to lower medium and low voltage grid expansion needs, that are consequently determined. Here, heuristic optimization methods using the non-linear power flow were developed. Applying the tool on future scenarios we derived cost-efficient grid and storage expansion for all voltage levels in Germany. Due to the integrated approach storage expansion and curtailment can significantly lower grid expansion costs in medium and low voltage grids and at the same time serve the optimal functioning of the overall system. Nevertheless, the cost-reducing effect for the whole of Germany was marginal. Instead, the consideration of realistic, spatially differentiated time series lead to substantial overall savings.

The objective of this article: analysis of research trends on the topic "Materials Science for Energy Engineering" for the period 2012-2021. Materials and methods: bibliometric analysis of data from the Scopus abstract database.Results. It is shown that this topic is developing faster than the general energy topics.The key feature of the research trends is a significant increase in work on the development of materials for renewable energy and a decrease in the number of publications related to nuclear power.The primary goal of many studies is to increase the efficiency of renewable energy production through the use of new materials.The importance of the topic is evidenced by the emergence of new journals that quickly entered the first quartile of the abstract databases Scopus and Web of Science, for example: ACS Applied Energy Materials.There has been a significant increase of interest in perovskite solar cells, layered semiconductors, triboelectric nanogenerators, cobalt compounds, sulfur compounds, and oxygen and hydrogen evolution reaction during Electrolysis.Publications on electric batteries are well represented in all time intervals. The focus is on electrode materials and battery efficiency.

Sources are classified into two depending upon the factor of reviving. These sources, which cannot be revived into their original shape once they are consumed, are considered as nonrenewable energy resources, i.e., (coal, fuel) Moreover, those energy resources which are revivable to the original condition even after being consumed are known as renewable energy resources, i.e., (wind, solar, hydel) Renewable energy is a cost-effective way to generate clean and green electrical energy Now a day’s majority of the countries are paying heed to energy generation from RES Pakistan is mostly relying on conventional energy resources which are mostly nonrenewable in nature coal, fuel is one of the major resources, and with the advent of time their prices are increasing on the other hand RES have great potential in the country with the deployment of RES greater reliability and an effective power system can be obtained In this thesis, a similar concept is being used and a hybrid power system is proposed which is composed of intermixing of renewable and nonrenewable sources The Source side is composed of solar, wind, fuel cells which will be used in an optimal manner to serve load The goal is to provide an economical, reliable, uninterruptable power supply. This is achieved by optimal controller (PI, PD, PID, FOPID) Optimization techniques are applied to the controllers to achieve the desired results. Advanced algorithms (Particle swarm optimization, Flower Pollination Algorithm) will be used to extract the desired output from the controller Detailed comparison in the form of tables and results will be provided, which will highlight the efficiency of the proposed system.