To address the problems of wind abandonment in the regional integrated energy system (RIES), which occurs when cogeneration unit operates in a heat-determined electricity operation mode, and the low efficiency of the energy storage system in a low-temperature environment, we propose an optimal scheduling method for RIES based on fine energy storage and wind power dissipation. First, a fine energy storage model is established on the source side and the conditional value at risk(CvaR) theory is used to quantify the uncertainty of wind power; then a combined heat and power demand response mechanism is introduced on the load side to reduce the peak-to-valley difference between heat and power loads, and to promote the consumption of wind power. Finally, with the objective of minimizing the total cost of RIES optimal dispatch, the example is solved on the MATLAB platform. The simulation results show that compared with the traditional model, the proposed model is not only more adaptable to the low-temperature environment, but also can effectively improve the system economy and wind power consumption.

Abstract: A two-year study of pearl millet-groundnut cropping systems across two fertilizer levels was conducted at the INRAN/TARNA research station in Maradi, Niger in the Sahelian zone of West Africa. The objective of this study was to identify the best cropping system with and without fertilizer application to optimize pearl millet and groundnut yields, land use efficiency, and economics as measured by value-to-cost ratio. The experiment was conducted with three replications, and ten treatments combination of five pearl millet and groundnut cropping systems (pearl millet and groundnut sole crops, and three pearl millet – groundnut intercrops), and two fertilizer levels. Sole cropping produced the highest pearl millet grain by over 300 kg ha-1 and groundnut pod yields by over 500 kg ha-1, but all the intercropping systems had a LER above 1.0 with land use efficiency increased by 19 to 41%, also intercropping increased diversity, and reduced risk. Fertilizer application increased yields in all cropping systems by 200 to 600 kg ha-1. Government subsidy increased the value-to-cost ratio by 0.5 to 2, 5 units, and was required for economic response for pearl millet sole and intercrops in 2022. The groundnut sole cropping system had the greatest economic response to fertilizer application. Based on the risky environment and multiple end uses needed by producers, the intercrop system M-G: 1:3:1 with fertilizer application is usually the best option to optimize pearl millet and groundnut production.

This paper develops feasible control strategies and associated system responses to bring an autonomous front-axle bicycle robot from specified initial conditions to final conditions such that a specific performance index is minimized. To solve the problem, the following approach is used: The feasible controls derived from the normal equations of optimality are substituted into the state and the costate systems and form a combined control-free state-costate system which is vectorized to enable and ease the application of a numerical method. A computer program written in Matlab computer programming language, codes a fourth-order Runge-Kutta numerical method and then solve the combined state-costate system of ordinary differential equations. The obtained results are the feasible bicycle robot trajectory, the feasible state functions, the feasible costate functions and the feasible control functions. Associated Computational Simulations are designed and provided to persuade on the effectiveness and the reliability of the approach.

Due to the increase in the emission of greenhouse gases, the hydrologic cycle is being altered on the daily basis. This has affected the variations in relations of intensity, duration, and frequency of rainfall events. Intensity Duration Frequency (IDF) curves describe the relationship between rainfall intensity, rainfall duration and return period. IDF curves are one of the most often applied implements in water resource engineering, in areas such as for operating, planning and designing of water resource projects, or for numerous engineering projects aimed at controlling floods. In particular, IDF curves for precipitation answer problems of improper drainage systems or conditions and extreme characters of precipitation which are the main cause of floods in Nyabugogo catchment. This study aims to establish Rainfall IDF empirical equations, curves and hydrological discharge (predicted peak rate of runoff (Qlogy)) equations for eight Districts that will be used for designing an appropriate and sustainable hydraulic structures for controlling flood to reduce potential loss of human and aquatic life, degradation of water, air and soil quality and property damage and economic lessen caused by flood in Nyabugogo catchment. However Goodness of Fit tests revealed that Gumbel’s Extreme-Value Distribution method appears to have the most appropriate fit compared with Pearson type III distribution for validating the Intensity-Duration-Frequency curves and equations through the use of daily annual for each meteorological station. The findings of the study show that the intensity of rainfall increases with a decrease in rainfall duration. Additionally, a rainfall of every known duration will have a higher intensity if its return period is high, while the predicted peak rate of runoff (Qlogy) increases also with an increase in the intensity of rainfall.

A family of linear singularly perturbed Cauchy problems is studied. The equations defining the problem combine both partial differential operators together with the action of linear fractional transforms. The exotic geometry of the problem in the Borel plane, involving both sectorial regions and strip-like sets, gives rise to asymptotic results relating the analytic solution and the formal one through Gevrey asymptotic expansions. The main results lean on the appearance of domains in the complex plane which remain intimately related to Lambert W function, which turns out to be crucial in the construction of the analytic solutions. On the way, an accurate description of the deformation of the integration paths defining the analytic solutions and the knowledge of Lambert W function are needed in order to provide the asymptotic behavior of the solution near the origin, regarding the perturbation parameter. Such deformation varies depending on the analytic solution considered, which lies in two families with different geometric features.

The work is devoted to the study of a family of linear initial value problems of partial differential equations in the complex domain, dealing with two complex time variables. The use of a truncated Laplace-like transformation in the construction of the analytic solution allows to overcome a small divisor phenomenon arising from the geometry of the problem and represents an alternative approach to the one proposed in a recent work by the first two authors. The result leans on the application of a fixed point argument and the classical Ramis-Sibuya theorem.

There are potentially promising mitigation activities for epidemic and pandemic scenarios that are not currently the subject of significant research effort. Large epidemics and pandemics pose risks that are important to mitigate, even if the likelihood of the events is low and uncertain. While some efforts are the subject of extensive funding and consideration, other approaches are neglected. Here, we consider such neglected interventions which could significantly reduce the impact of such an epidemic or large-scale pandemic. These are identified via a narrative literature review of extant literature reviews and overviews of mitigations in epidemic and pandemic situations, followed by consideration of the economic value of information of further study of heretofore neglected interventions and approaches.Based on that analysis, we considered several classes of mitigations, and conducted more exploratory reviews of each. Those discussed include mitigations for (1) reducing transmission, such as personal protective equipment and encouraging improved hygiene, (2) reducing exposure by changing norms and targeted changes for high-risk or critical professions and activities, (3) reducing impact for those infected, and (4) increasing large scale resilience using disaster and infrastructure continuity planning.Some proposed mitigations are found to be of low marginal value. Other mitigations are likely to be valuable, but the concepts or applications are underdeveloped. In those cases, further research, resources, or preparation are valuable for mitigating both routine and extreme disease outbreak events. Still more areas of research are identified as having uncertain value based on specific but resolvable uncertainties. In both of the latter cases, there is no guarantee that mitigations identified as worthy of further consideration will be valuable, but the argument for further research is clear.

Though innovations for sustainable management of natural resources have emerged over time, the rising demand for nature based health solutions and integration of endemic flora into global value chains could have adverse impacts on ecosystems. The ecological risks in the exploitation of wild medicinal plant resources are exacerbated by a myriad of agrotechnological risks and challenges that highly constrain their domestication. Successful exploitation and commercialization of medicinal plants thus require a clear understanding of their demand and production systems or value chain analysis. Accordingly there is need for innovative approaches towards their integration into global value chains. Since quality and safety, traceability, certification, as well as, consumer tastes and preferences are critical drivers in purchasing decisions by global consumers, they are inadvertently exploited to weaken Indigenous knowledge (IK), undermine common property rights and entrench value chains that favour a few elite buyers. This tend to create pervasive incentives for overexploitation of medicinal plant resources and environmental degradation. Potential solution lies in the recognition of drivers of vulnerability to environmental degradation and the innovative use of policy bricolage, feedback loops and interactions between knowledge, power and agency on one hand, and collective action and property rights institutions on the other hand. We conceptualise a framework that can mediate a transformational agenda and enhance systematic understanding of sustainability lenses in endemic medicinal plant resources value chains. This could in turn strengthen IK, enhance collective action and promote participation of local actors with positive impact on the utilisation and integration of endemic medicinal plant resources into global value chains.

Recent pollinator declines have focused efforts on their conservation which require clear estimates of pollination value to agriculture. Our socio-economic producer surveys and agronomic field research data were used to present a new way of estimating ecosystem service value of native pollinators. Using two regionally important U.S.A. crops, Maine wild blueberry and Massachusetts cranberry as models, we present perceived values of native bee pollinators from both consumer and producers. Wild blueberry’s Replacement Cost (RC) was greater than Attributable Net Income (ANI), since greater rented honey bee stocking densities are required. Attributable Net Income for native bees were similar for wild blueberry ($613/ha) and cranberry ($689/ha). Marginal Net Farm Income (MNFI) from incrementally adding more hives per ha was greater from stocking a third/fourth hive per ha for cranberry ($6,206) than stocking a ninth/tenth hive per ha for wild blueberry ($556), given greater responsiveness of yield, revenue, and profit to using rented honey bee hives in cranberry compared to wild blueberry. Both crops’ producers were only willing to annually invest $140–188/ha in native pollination enhancements on their farms, justifying government support. Consumers are willing to pay ~6.7 times more to support native bees than producers, supporting market-based support for invertebrate conservation.

In order to meet the military requirements of the fuze, such as precision strike, efficient mutilates ability and low collateral damages, the microminiaturization is an inevitable trend of secure system. Based on the silicon-based MEMS S&A device designed by our term, the design principles of each module and fabrication process are introduced. The average fracture strength and Young's modulus of the silicon are 726 MPa and 175 GPa from the tensile test, respectively. From Hopkinson impact experiment, we can get the threshold-value judging mechanism being safety under the impact overload of 20526 g, and this value is much more than the standard of the drop overload 12000g; the arming value under the centrifugal overload obtained from theory, simulation and experiment is at the range of 28200 g and 32000 g, it shows that the threshold-value judging mechanism can be arming compared with the value 35951g of design principle. Therefore, the threshold-value judging mechanism can meet the design requirements of overload. Furthermore, the relationship of fracture threshold-values obtained by different theories is found out through parametric design method, as shown in Figure 14, it provides the theory evidence to the follow parametric design.

We show how the Poincar\'e--Riemann--Hilbert boundary-value problem enables us to construct effective estimates of the potential in the Schr\"odinger equation. The apparatus of the three-dimensional inverse problem of quantum scattering theory is developed for this. It is shown that the unitary scattering operator can be studied as a solution of the Poincar\'e--Riemann--Hilbert boundary-value problem. This allows us to go on to study the potential in the Schr\"odinger equation

The purpose of the research is to investigate the unique solvability of a nonlocal boundary value problem for a loaded equation of parabolic-hyperbolic type in a special domain. Methods: Using representations of a general regular solution, the existence and uniqueness of the problem posed is proved. Results: A new method for proving the unique solvability of nonlocal boundary value problems for one loaded equation of mixed type in a special domain has been formed and developed. Conclusions: The obtained results make it possible to solve some problems of genetics, immunology, transonic gas dynamics and thermal physics, which are associated with displacement.

Knowledge is a property that measures the degree of awareness of an agent about a target in an environment. The goal in conventional intelligent and cognitive agent development is to build agents that can be trained to gain knowledge about a target. The definition and operations of this knowledge associated to the agent is not clear, whereas these are required for developing a reliable, scalable and flexible agent. In this paper, we provide a concise theoretical framework for the description and quantification of the knowledge property needed for an efficient design of cognitive and rational intelligent agents. We relate the quantification scheme to the epistemological description of knowledge and present many illustrative examples on the usefulness of the quantification scheme.

This paper aims at computing feasible control strategies and the corresponding feasible state trajectories to drive an autonomous rear-axle bicycle robot from a given initial state to a final state such that the total running cost is minimized. Pontryagin’s Minimum Principle is applied and derives the optimality conditions from which the feasible control functions, expressed as functions of state and costate variables, are substituted into the combined state-costate system to obtain a new free-control state-costate nonlinear system of ordinary differential equations. A computer program was written in Scilab to solve the combined state-costate system and obtain the feasible state functions, the feasible costate functions and the feasible control functions. Associated Computational Simulations were provided to show the effectiveness and the reliability of the approach.

In the European Union (EU), cannabidiol products require pre-marketing authorisation under the novel food regulation. Currently, 19 CBD applications are under assessment at the European Food Safety Authority (EFSA). During the initial assessment of the application files, the EFSA Panel on Nutrition, Novel Foods and Food Allergens (NDA) located several knowledge gaps in their 07 June 2022 statement on safety of cannabidiol as a novel food that need to be addressed before the evaluation of CBD can be concluded. Namely, the effect of CBD on the liver, gastrointestinal tract, endocrine system, nervous system, psychological function, and reproductive system needs to be clarified. Nevertheless, the available literature allows a benchmark dose (BMD)-response modelling of several bioassays, resulting in a BMD lower confidence limit (BMDL) of 20 mg/kg bw/day for liver toxicity in rats. Human data in healthy volunteers found increases in the liver enzymes alanine aminotransferase (ALT) and aspartate aminotransferase (AST) in a study at 4.3 mg/kg bw/day, which was defined by EFSA NDA panel as a lowest observed adverse effect level (LOAEL). The EFSA NDA panel currently concluded that the safety of CBD as a novel food cannot be evaluated, leading to a so-called clock stop of the applications until the applicants provide the required data. Meanwhile, the authors suggest that CBD products still available as food supplements on the EU market despite the lack of authorisation must be considered as “unsafe”. Products exceeding a health-based guidance value of 10 mg/day must be considered as being “unfit for consumption” (Article 14(1) and (2) (b) of Regulation No 178/2002), while the ones in exceedance of the human LOAEL must be considered “injurious to health” (Article 14(1) and (2) (a) of Regulation No 178/2002).

The present review is dedicated to using of peat on the example of fen peat in high added-value products and applications. Mainly, but not limited, last decade literature was analysed from the perspective of innovation potential of peat applications in environmental technologies on examples of studies from the Baltic Sea region. Paper covers a wide range of applications of peat products started from agriculture to medicine and cosmetics. A separate chapter is devoted to the deep-processed peat product - humic substances (humate, humic and fulvic salts and acids). Generalised dependence of product extraction rate and its properties, depending on the process parameters are provided. Widely are described applications of the humic sub-stance applications covering economic aspects, such as production costs. In the last chapter of the review are given recommendations for applications considering the most recent trends of peat-based product developments. This accumulated information could be useful for future production, development of new, environmentally friendly products and start-ups establishment.

In this work the existence and nonexistence of stationary radial solutions to the elliptic partial differential equation arising in the molecular beam epitaxy are studied. Since we are interested in radial solutions we arrive at the following fourth-order differential equation

This paper is a slightly modified, abridged version of a previous work ``Parametric Gevrey asymptotics in two complex time variables through truncated Laplace transforms'' motivated by our contribution in the conference ``Formal and Analytic Solutions of Diff. (differential, partial differential, difference, q-difference, q-difference-differential) Equations on the Internet'' (FASnet20). It aims to clarify and give further detail at some crucial points concerning the asymptotic behavior of the solutions of the problems studied in that work.

This paper is a slightly modified, abridged version of a previous work "Parametric Gevrey asymptotics in two complex time variables through truncated Laplace transforms'' motivated by our contribution in the conference "Formal and Analytic Solutions of Diff. (differential, partial differential, difference, q-difference, q-difference-differential) Equations on the Internet'' (FASnet20). It aims to clarify and give further detail at some crucial points concerning the asymptotic behavior of the solutions of the problems studied in that work.

The properties of iterative splitting methods with serial versions have been analyzed since recent years, see [1] and [3]. We extend the iterative splitting methods to a class of parallel versions, which allow to reduce the computational time and keep the bene t of the higher accuracy with each iterative step. Parallel splitting methods are nowadays important to solve large problems, which can be splitted in subproblems and computed independently with the dierent processors. We present a novel parallel iterative splitting method, which is based on the multi-splitting methods, see [2], [10] and [15]. Such a exibilisation with multisplitting methods allow to decompose large iterative splitting methods and recover the bene t of their underlying waveform-relaxation (WR) methods. We discuss the convergence results of the parallel iterative splitting methods, while we could reformulate such an error to a summation of the individual WR methods. We discuss the numerical convergence of the serial and parallel iterative splitting methods and present dierent numerical applications to validate the bene t of the parallel versions.

In this paper we present a review of recent developments in AI towards the possibility of an artificial intelligence equals that of human intelligence. AI technology has always shown a stepwise increase in its capacity and complexity. The last step took place several years ago, with the increased progress in deep neural network technology. Each such step goes hand in hand with our understanding of ourselves and our understanding of human cognition. Indeed, AI was always about the question of understanding human nature. AI percolates into our lives, changing our environment. We believe that the next few steps in AI technology, and in our understanding of human behavior, will bring about much more powerful machines, flexible enough to resemble human behavior. In this context, there are two research fields: Artificial Social Intelligence (ASI) and General Artificial Intelligence (AGI). The authors also allude to one of the main challenges for AI, embodied cognition, and explain how it can viewed as an opportunity for further progress in AI research.

Changes in extreme weather patterns are expected under climate change. In this study, a risk assessment was conducted using 4 building damage history datasets and 33 weather datasets (precipitation, wind speed, snow, and temperature) from 230 regions in South Korea to quantitatively analyze and predict building damage caused by potential future natural disasters. Decision tree analysis was used to evaluate building damage risk in 230 regions. The decision tree model to determine the risk of flood, gale, and typhoon was generated, which excluded gales, with less damage. The weight (variable importance) and limit value (damage limit) of the weather variables ware derived using the decision tree model. Using these two factors, we assessed the building damage risk in 230 regions in South Korea until 2100. The number of regions at risk of flood damage increased by more than 30% in average. Conversely, regions at risk of snowfall damage decreased by more than 90%. The regions at risk of typhoons decreased by 57.5% on average, and the number of regions at high risk of typhoon damage increased by up to 62.5% in RCP 8.5. These results can be used as objective data to minimize future building damage throughout South Korea, representing the first step towards sustainable development in the region with respect to disaster response.

The valorization of aquaculture/fisheries processing by-products, as well as unavoidable/unwanted catches and discards in Greece is currently an underutilized activity despite the fact that there are several best practices in Northern Europe and overseas. One of the main challenges is to determine whether the available quantities for processing are sufficient to warrant valorization of discards and fish side streams. This is the first attempt to systematically record and analyze the available quantities of fish by-products and discards in Greece in a spatial and temporal way in an effort to create a national exploitation Master Plan for the valorization of this unavoidable and unwanted biomass. A thorough survey conducted within the VIOAXIOPIO project unveiled a substantial biomass of around 19,000 tonnes annually that could be harnessed for valorization. Furthermore, the production of various High Added Value Biomolecules (HAVB) was investigated, and experimental trials were conducted to assess the potential yields and the collected data were used to formulate four valorization scenarios.

The advent of social commerce (SC) has transformed the landscape of online consumer behavior, emphasizing the significance of customer-to-customer relations in shaping sustainable relation-ships with customers. This research investigated the intricate relationships between social com-merce dimensions, particularly suggestions and recommendations, forums and communities, and ratings and reviews, and their influence on customer-to-customer value co-creation (C2CVCC) and sustainable customer relationships (SCRs). A questionnaire was designed and administered to 635 respondents. We examined the psychometric properties of the measurements and subse-quently applied Partial Least Squares as a Structural Equation Modeling method (PLS-SEM) for hypothesis testing. The findings reveal that the dimensions of SC significantly impact C2CVCC, with ratings and reviews playing a pivotal role. Furthermore, C2CVCC emerges as a substantial mediator in the path between SC and SCRs. The empirical analysis showcases strong support for the proposed model, with robust path coefficients (β) and p-values confirming direct and indirect effects. These findings offer valuable insights for businesses seeking to leverage SC and customer interactions to enhance SCRs in the digital era. Understanding the dynamics of C2CVCC within the context of SC has become essential for marketers and businesses aiming to thrive in today's competitive online marketplace.

This study examined the effect of the media usage environment, particularly TV and mobile devices, on advertisement acceptance, lifestyle, and psychological satisfaction. Hypothesis pathways and comparative structural mediating effects were analyzed. Media and Consumer Research public data were used for empirical analysis. A total of 6,640 people who participated in sports activities were included in the study. The results demonstrated that TV and mobile device usage environments had similar effects on advertisement acceptance. While TV did not influence the pursuit of personal life, mobile device use environments affected the pursuit of personal life. Mobile device use environments had a greater effect on individual psychological satisfaction than TV. Adoption had a mediating effect on the influence of media usage environments on the pursuit of personal life. The pursuit of a personal life had a significant mediating effect on the influence of media use environments on psychological stability. This study revealed no differences in the effects of new and traditional media on advertisement acceptance, while new media had a greater influence on lifestyle and psychological satisfaction.

This article analyzes 6 probability distributions from the Generalized Pareto family, with 3, 4 and 5 parameters, with main purpose to identify other distributions from this family with applicability in flood frequency analysis compared to the distribution already used in the literature from this family such as Generalized Pareto Type II and Wakeby. This analysis is part of a larger and more complex research carried out in the Faculty of Hydrotechnics regarding the elaboration of a norm for flood frequency analysis using the linear moments method. In Romania, the standard method of parameter estimation is the method of ordinary moments, thus the transition from this method to the method of linear moments is desired. All the necessary elements for the distributions use are presented like, the probability density functions, the complementary cumulative distribution functions, the quantile functions, the exact and approximate relations for estimating parameters, for both methods of parameters estimation. All these elements are necessary for a proper transition between the two methods, especially since the use of the method of ordinary moments is done by choosing the skewness of the observed data depending on the origin of the maximum flows. A flood frequency analysis case study, using annual maximum and annual exceedance series, was carried out for the Prigor river, to numerically present the analyzed distributions. The performance of this distributions is evaluated using relative mean error, relative absolute error and linear moments diagram.

The main aim of this paper is to analyse the performance of different intelligent compaction measurement values (ICMVs) and compare them with spot test measurements for asphalt pavement. To accomplish this, a two-layer asphalt testbed was constructed using an instrumented double-drum roller. All ICMVs [compaction meter value ( ), compaction control value ( ), roller-integrated stiffness ( ), and vibratory modulus ( )] were calculated using the same accelerometer data collected during the construction of the asphalt testbed. A novel method using the cross-correlation technique was developed to estimate the phase lag between the excitation force of the roller drum and the ground reaction, which is required for and calculations. The analysis of ICMV data showed a strong correlation between and , while and demonstrated a strong correlation only when double jump of the roller drum did not occur. Further, none of the ICMVs recorded during the last roller pass of asphalt compaction showed an acceptable correlation with asphalt densities [measured using a non-nuclear density gauge (NNDG)], mainly due to the influences of the underlying support and asphalt temperature on ICMVs. A correction method to decouple the influence of underlying support on was developed and validated using existing data from the literature. The applicability of this method for different field scenarios was demonstrated using numerical modelling.

Modified structure along latent tracks and track formation process have been investigated in poly(allyl diglycol carbonate), PADC, which is well recognized as a sensitive etched track detector. This knowledge is essential to develop novel detectors with improved track registration property. The track structures of protons and heavy ions (He, C, Ne, Ar, Fe, Kr and Xe) have been examined by means of FT-IR spectrometry, covering the stopping power region between 1.2 to 12,000 eV/nm. Through a set of experiments on low-LET radiations – such as gamma ray -, multi-step damage process by electron hits was confirmed in the radiation-sensitive parts of the PADC repeat-unit. From this result, we unveiled for the first-time the layered structure in tracks, in relation with the number of secondary electrons. We also proved that etch pit was formed when at least two repeat-units were destroyed along the track radial direction. To evaluate the number of secondary electrons around tracks, a series of numerical simulations were performed with Geant4-DNA. Therefore, we are proposing new physical criterions to describe the detection thresholds. Futhermore, we propose a present issue of the definition of detection threshold for semi-relativistic C ions. And as a possible chemical criterion, formation density of hydroxyl group is suggested to express the response of PADC.

Attackers are perpetually modifying their tactics to avoid detection and frequently leverage legitimate credentials with trusted tools already deployed in a network environment, making it difficult for organizations to proactively identify critical security risks. Network traffic analysis products have emerged in response to attackers’ relentless innovation, offering organizations a realistic path forward for combatting creative attackers. Additionally, thanks to the widespread adoption of cloud computing, Device Operators (DevOps) processes, and the Internet of Things (IoT), maintaining effective network visibility has become a highly complex and overwhelming process. What makes network traffic analysis technology particularly meaningful is its ability to combine its core capabilities to deliver malicious intent detection. In this paper, we propose a novel darknet traffic analysis and network management framework to real-time automating the malicious intent detection process, using a weight agnostic neural networks architecture. It is an effective and accurate computational intelligent forensics tool for network traffic analysis, the demystification of malware traffic, and encrypted traffic identification in real-time. Based on Weight Agnostic Neural Networks (WANNs) methodology, we propose an automated searching neural net architectures strategy that can perform various tasks such as identify zero-day attacks. By automating the malicious intent detection process from the darknet, the advanced proposed solution is reducing the skills and effort barrier that prevents many organizations from effectively protecting their most critical assets.

Fundamental principles of classical (Newtonian) physics are employed to probe the cosmological lambda Λ; it yields the values ρ_vac = 2.61 x 10^-39 g cm^-3 and Λ = 4.87 x 10^-66 cm^-2. It is revealed that Λ is a fundamental physical constant defined by vacuum density-light speed ρ_vacc² correlation. However, the constant accelerates along the groups and periods of a universal spatial periodicity equivalent to the chemical periodicity. Previous results are cited to show that chemical elements are quantum harmonic (periodic) oscillators QHOs and their waveform oscillations exclusively define the vacuum field. The cosmological periodic unit CPU is introduced, it relies on the cosmological principle to argue that a relative physical quantity evaluated for the QHO applies to constituents of corresponding cosmological spatial quanta. Compelling evidences, backed with relevant data and quantitative expressions, are then presented to argue that: there was never a big bang, it is a Linde-universe sans “chaotic”; nature posts no singularity; mass does not curve spacetime, neither does metric space curvature trace directly to gravitation nor particle creation, gravity is classical, not quantum; reality is quadri-phasic not mono-phasic with a clear distinction between the atomic waveform defined with absolute atomic mass and condensed matter defined with relative atomic mass; every chemical element exists in three particle-generations thus, dark matter is invisible form (conjugate) of the visible element, its waveform manifests dark energy, it is not implicated in metric space expansion; Planck scale does not exist, radioactivity constrains fundamental length to atomic radius of the heaviest element.

Hydroponic farming systems play an increasingly important role in the sustainable production of nutrient-rich foods. The contamination of surfaces in hydroponic fresh produce production poses risks to the food safety of crops, potentially endangering public health and causing economic losses in the industry. While sanitizers are widely used in commercial hydroponic farms, their effectiveness against human pathogens on surfaces, and their impact on plant health and quality are not known. In this study, we evaluated the efficacy of chemical sanitizers in eliminating Salmonella Typhimurium from inanimate surfaces in commercial hydroponic Nutrient Film Technique (NFT) systems. Further, we assessed the impact of sanitizers on the yield, quality, and nutritional value of lettuce and basil. Sanitizers (Virkon, LanXess; Sanitate 12.0, Bi-oSafe Systems; Kleen Grow, Pace Chemical Ltd.; Green Shield, United Labs Inc.; Zerotol, BioSafe Systems; Bleach, Pure Bright), were tested against Salmonella Typhimurium inoculated on NFT surfaces (nutrient reservoirs, growing channels, top covers, drain lines). The effective treatments were then tested for their impact on lettuce and basil in a split-plot experiment conducted in commercial NFT units. Crop yield, color, and nutrient content were measured throughout the crop life cycle. While all quaternary ammonium compounds (QAC), SaniDate 12.0 (200ppm), Zorotol (5%), and Virkon (1%) eliminated Salmonella Typhimurium from commercial NFT surfaces, chlorine-based sanitizer treatments were statistically similar to water treatments on most surfaces. All chemical sanitizers impacted the yield, color, and nutritional value of lettuce and basil. SaniDate 12.0 (200ppm) was the least detrimental to crops and was identified as a potential candidate for further validation in commercial hydroponic settings. The findings of this study will be translated into recommendations for the industry and will contribute to the development of future food safety guidelines and policies.

This study aims to clarify the influence of photographic environments under different light sources on image-based SPAD value prediction. Radish leaf patches of 1.5 cm diameter were photographed under halogen or LED light. The input variables for the SPAD value prediction using random forests were RGB values, HSL values, and HSV values. Additionally, the light color temperature (LCT) and illuminance (ILL) were used as the input variables. Model performance was assessed using Pearson’s correlation coefficient (COR), Nash-Sutcliffe efficiency (NSE), and root mean squared error (RMSE). SPAD value prediction resulted in high accuracy in a stable light environment; CORRGB+ILL+LCT and CORHSL+ILL+LCT were 0.929 and 0.922, respectively. Image-based SPAD value prediction was effective under halogen light with a similar color temperature at dusk; CORRGB+ILL and CORHSL+ILL were 0.895 and 0.876, respectively. The HSL value under LED could be used to predict the SPAD value with high accuracy; COR, NSE, and RMSE were 0.972, 0.944, and 2.07, respectively. The partial dependence plots of the H value indicate a change from blue to green with increasing SPAD values. Further studies are required to examine this method under outdoor conditions in spatiotemporally dynamic light environments.

Data is present in the data sources like Files and Data bases, Retrieval of information from that data sources is one of the important issue nowadays. So for retrieval information from the data sources clustering is used. In the present market different types of clustering algorithms were available. But opting of the clustering is based on user requirements. This paper focuses on the study of hierarchical clustering approach on different conditions or measures or with customer choices like clustering process number of clusters generated at each level, number of levels, attributes range for performing the clustering on the given data set. In brief overview we discuss the hierarchical approach for clustering algorithm with the user opting choices.

Overcoming the issue of land value and cost in urban areas will not provide a miraculous solution to the problems there. Appropriate land use cost, especially for residential and commercial land, is just one of the issues to be settled in the debate. Therefore, this study aims to build a new urban land price determination model by investigating the urban syntactical analysis, street width, and their economic effects on land value. The study attempts to determine the impact of syntactic analysis of streets and street width on land prices; it also seeks to identify the factor most affected by the land cost. Ultimately, the study built a model for urban land price prediction. The case selected is evaluated and compared in three aspects of the analysis, including; the urban axial assessments and urban street width, to find out their impacts on the real estate’s land price in the context of the land use distributions, which are predominantly residential and commercial types of uses. Depth map X8, SPSS, and QGIS 3.16 were used for the study evaluations and assessments. The result showed a significant impact of the urban street network on the price of land; this result can be used to enhance future urban design regarding urban economy improvements.

Manufacturing corporations has the acceptance of the Outsourcing Process (OP) to improve industrial activities as well as to archive the revenue objectives, and with this, Risk Analysis (RA) tools are constantly used to assure expected results. Failure Mode and Effect Analysis (FMEA) is one of preferred RA tools, moreover, it is proven that FMEA adds uncertainty because of the human participation at the RA, afterward it is demonstrated that Pythagorean Fuzzy Dimensional Analysis – FMEA – Value Stream Mapping (PFDA-FMEA-VSM) method removes the uncertainty in RA, likewise it aids to the stakeholders for decision making, giving more advantages improving the use of the resources on the project. This document exhibits a real case scenario in a manufacturing firm applying PFDA-FMEA-VSM method adapted for manufacturing OP. The application of PFDA-FMEA-VSM shows solid RA results, removing the human intervention uncertainty added to the risk ranking, gives advantages to the stakeholders for visualize the main risks in detailed diagram, as well as make easier to take better decisions on where to apply resources and mitigate risks during OP.

Noise reduction in medical images is a perplexing undertaking for the researchers in digital image processing. Noise generates maximum critical disturbances as well as touches the medical images quality, ultrasound images in the field of biomedical imaging. The image is normally considered as gathering of data and existence of noises degradation the image quality. It ought to be vital to reestablish the original image noises for accomplishing maximum data from images. Medical images are debased through noise through its transmission and procurement. Image with noise reduce the image contrast and resolution, thereby decreasing the diagnostic values of the medical image. This paper mainly focuses on Gaussian noise, Pepper noise, Uniform noise, Salt and Speckle noise. Different filtering techniques can be adapted for noise declining to improve the visual quality as well as reorganization of images. Here four types of noises have been undertaken and applied on medical images. Besides numerous filtering methods like Gaussian, median, mean and Weiner applied for noise reduction as well as estimate the performance of filter through the parameters like mean square error (MSE), peak signal to noise ratio (PSNR), Average difference value (AD) and Maximum difference value (MD) to diminish the noises without corrupting the medical image data.

Urban transit planning is going through a transition to greater private investment in many parts of the world and is now on the agenda in Australia. After showing examples of private investment in transit globally the paper focuses on historical case studies of private rail investment in Western Australia. These case studies mirror the historical experience in rapidly growing railway cities in Europe, North America and Asia (particularly Japan), and also the land grant railways that facilitated settlement in North America. The Western Australian experience is noteworthy for the small but rapidly growing populations of the settlements involved, suggesting that growth, rather than size, is the key to successfully raising funding for railways through land development. The paper shows through the history of transport, with particular reference to Perth, that the practice of private infrastructure provision can provide lessons for how to enable this again. It suggests that new partnerships with private transport investment as set out in the Federal Government City Deal process, should create many more opportunities to improve the future of cities through once again integrating transit, land development and private finance.

The actions of many drugs involve enzyme inhibition. This is exemplified by the inhibitors of monoamine oxidases (MAO) and the cholinsterases (ChE) that have been used for several pharmacological purposes. This review describes key principles and approaches for the reliable determination of enzyme activities and inhibition as well as some of the methods that are in current use for such studies with these two enzymes. Their applicability and potential pitfalls arising from their inappropriate use are discussed. Since inhibitor potency is frequently assessed in terms of the quantity necessary to give 50% inhibition (the IC50 value), the relationships between this and the mode of inhibition is also considered, in terms of the misleading information that it may provide. Incorporation of more than one functionality into the same molecule to give a multi-target-directed ligands (MTDLs) requires careful assessment to ensure that the specific target effects are not significantly altered and that the kinetic behaviour remains as favourable with the MTDL as it does with the individual components. Such factors will be considered in terms of recently developed MTDLs that combine MAO and ChE inhibitory functions.

Textile and clothing is one of the most important industrial sectors, not only due to the significant number of jobs generated, but also because it addresses one of the people’s fundamental needs (clothing). It is, however, a sector with a huge environmental impact, all over the world, and also an important social impact, especially in developing countries. Sustainability in the Textile & Clothing value chain is a known issue, concerning both environmental, and economical-social facets of sustainability. One way to improve sustainability in this sector is by measuring the environmental, economic and social impacts of value chain activities and, ultimately, computing an Environmental and Circular score for each batch of textile and clothing product, and an Economical and Social score for each involved firm, reflected in their products. The consumer will then have the opportunity and responsibility for selecting products with the least negative environmental, economical and social impact. This article presents the results of STVgoDigital project - PPS1, developed in Portugal with the aim of implementing the traceability of textile and clothing products, boosting sustainability in this sector, and preparing the ground for the implementation of the circular economy. More exactly, a blockchain-based textile and clothing value-chain traceability platform is presented, for tracing textile product lots and activities, along the value chain, classifying them with a score, which measures their environmental and social impact. The environmental, economic and social impact scores are based on a set of proposed indicators. The results are assessed through the presentation of a case study of a face towel (home textile) and a case study of a T-shirt (clothing).

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.

Purpose: This research compared the dissociated phoria at near and distance fixation in free space using three techniques: the Howell test, alternate Cover test, and Thorington test. Methods: 220 healthy Mexican children (age 5.06-17.11) participated in this study. Phorias were quantified at both distances using each test, from the least to the most disruptive. The stereopsis degree and near point of convergence (break/recovery) were analyzed to understand their role on the visual system's sensorimotor balance. Results: For the exophoria/esophoria at near, the alternate Cover and Thorington tests showed similar values. The exophoria at distance, was similar with the alternate Cover and Howell tests, while esophoria, with the alternate Cover and Thorington tests. The break value and near exophoria relates to each other and affect the stereopsis degree, whereas age is associated with the stereopsis degree and break value. Conclusions: The analysis revealed that alternate Cover and Thorington tests can substitute one another, but not with the Howell test. The test's specific dissociation method may explain these results. Analyzing the binocular visual system provides information about its sensorimotor balance and fragility when faced to the technique’s degree of dissociation.

Tailoring treatment in patients with Hodgkin lymphoma (HL) is paramount to maximize outcomes while avoiding unnecessary toxicity. We aimed to compare the performance of SUVmax reduction (ΔSUVmax%) versus Deauville score (DS) in assessing chemotherapy response in pediatric HL patients undergoing 18F-FDG PET-CT. Fifty-two patients with biopsy-proven HL (age 8-16 years) were enrolled at baseline, interim (after the 2nd or 3rd chemotherapy round), and post-therapy (upon completion of first-line chemotherapy) 18F-FDG PET-CT. Interim and post-therapy DS and ΔSUVmax% were compared as response predictors. Patients were classified as responders and non-responders based on 24-month clinical follow-up. Interim DS showed a sensitivity, specificity, positive predictive value (PPV), negative predictive value (NPV) and diagnostic accuracy of 100%, 80.4%, 100%, 40% and 82.7%, respectively in predicting response. Post-therapy DS showed a sensitivity, specificity, PPV, NPV and accuracy of 66.7%, 97.8%, 95.7%, 80% and 94.2%. Interim ΔSUVmax% showed a sensitivity, specificity, PPV, NPV and accuracy of 83.3%, 82.6%, 97.4%, 38.5% and 82.7%, with a 56.3% cutoff. Post-therapy ΔSUVmax% showed a sensitivity, specificity, PPV, NPV and accuracy of 83.3%, 84.8%, 97.5%, 41.7% and 84.6%, with a 76.8% cutoff. Sensitivity, specificity (p<0.05) and NPV (p<0.01) were significantly higher using DS than ΔSUVmax%. In conclusion, DS can predict chemotherapy response better than ΔSUVmax% in pediatric HL patients.

Quantitative biomarkers derived from positron-emission tomography/computed tomography (PET/CT) have been suggested as prognostic variables in immune-checkpoint inhibitor (ICI) treated non-small cell lung cancer (NSCLC). As such data for first-line ICI therapy and especially for chemotherapy-ICI combinations are still scarce, we retrospectively evaluated baseline 18F-FDG-PET/CT of 85 consecutive patients receiving first-line pembrolizumab with chemotherapy (n=70) or as monotherapy (n=15). Maximum and mean standardized uptake value, metabolic tumor volume (MTV), total lesion glycolysis and bone marrow-/ spleen to liver ratio (BLR/SLR) were calculated. Kaplan-Meier analyses and Cox-regression models were used to assess progression-free/overall survival (PFS/OS) and their determinant variables. Multivariate selection for PFS/OS revealed MTV as most relevant PET/CT biomarker (p<0.001). Median PFS/OS were significantly longer in patients with MTV≤70mL versus >70mL (PFS: 10 months (M; 95% confidence interval 4-16) vs. 4M (3-5), p=0.001; OS: not reached vs. 10M (5-15), p=0.004). Disease control rate was 81% vs. 53% for MTV≤/>70mL (p=0.007). BLR ≤1.06 versus >1.06 was associated with better outcomes (PFS: 8M (4-13) vs. 4M (3-6), p=0.034; OS: 19M (12-/) vs. 6M (4-12), p=0.005). In patients with MTV>70mL, concomitant BLR≤1.06 indicated a better prognosis. Higher MTV is associated with inferior PFS/OS in first-line ICI treated NSCLC, with BLR allowing additional risk stratification.

We consider a family of nonlinear singularly perturbed PDEs whose coefficients involve a logarithmic dependence in time with confluent Fuchsian singularities that unfold an irregular singularity at the origin and rely on a single perturbation parameter. We exhibit two distinguished finite sets of holomorphic solutions, so-called outer and inner solutions, by means of a Laplace transform with special kernel and Fourier integral. We analyze the asymptotic expansions of these solutions relatively to the perturbation parameter and show that they are (at most) of Gevrey order 1 for the first set of solutions and of some Gevrey order that hinges on the unfolding of the irregular singularity for the second.

While human activities and climate change are threatening available natural ecosystems, targeted studies on the biological cycle, propagation, and cultivation of threatened species are crucial both for their conservation and sustainable exploitation. This study was designed to bridge extant research gaps regarding the vulnerable local endemic Campanula pelviformis, a wild edible green traditionally consumed in Crete (Greece) with agro-alimentary and medicinal interest as well as ornamental value. New knowledge was obtained on the abiotic environmental conditions prevailing in its wild habitats (natural distribution mapped in Geographical Information Systems and linked with open-source databases). We collected seeds from wild-growing populations (three lowland, two semi-mountainous), we tested their germination at four different temperatures (10, 15, 20 and 25oC) and under different light conditions (light/dark and darkness), and we performed fertilization trails [integrated nutrient management (INF), chemical fertilization (ChF), control] examining morphological and physiological characteristics, above- and below-ground macro- and micronutrients contents, as well as their phenol content and antioxidant capacity. There were population and temperature effects on seed germination and their interaction was statistically significant. Campanula pelviformis germinated better at 10 and 15 oC (&gt;85% for all populations) with no preference on light conditions (98.75% and 95% in light and dark conditions). The INF application increased root dry mass, chlorophyll content index and chlorophyll fluorescence compared to other treatments and was beneficial for macro- and micronutrients concentrations in above-ground parts compared to previously studied wild-growing material, while below-ground parts were positively impacted by both fertilization types. Total phenols and antioxidant capacity were both increased by ChF fertilization. The data furnished herein led to the re-evaluation and upgrade of the feasibility and the readiness timescale for its sustainable exploitation in different economic sectors.

Digital federated platforms and data cooperatives for secure, trusted and sovereign data exchange will play a central role in the construction industry of the future. With the help of platforms, cooperatives and their novel value creation, the digital transformation and the degree of organization of the construction value chain can be taken to a new level of collaboration. The goal of this research project was to develop an experimental prototype for a federated innovation data platform along with a suitable exemplary use case. The prototype is to serve the construction industry as a demonstrator for further developments and form the basis for an innovation platform. It exemplifies how an overall concept is concretely implemented along one or more use cases that address high-priority industry pain points. This concept will create a blueprint and a framework for further developments, which will then be further established in the market. The research project illuminates the perspective of various governance innovations to increase industry collaboration, productivity and capital project performance and transparency as well as the overall potential of possible platform business models. However, a comprehensive expert survey revealed that there are considerable obstacles to trust-based data exchange between the key stakeholders in the industry value network. The obstacles to cooperation are predominantly not of a technical nature, but of a competitive, predominantly trust-related nature. To overcome these obstacles and create a pre-competitive space of trust, the authors therefore propose the governance structure of a data cooperative model, which is discussed in detail in this paper.

The objective of this paper is to research the impact of electrical and physical parameters that characterize the complementary MOSFET transistors (NMOS and PMOS transistors) in the CMOS inverter for static mode of operation. In addition to this, the paper also aims at exploring the directives that are to be followed during the design phase of the CMOS inverters that enable designers to design the CMOS inverters with the best possible performance, depending on operation conditions. The CMOS inverter designed with the best possible features also enables the designing of the CMOS logic circuits with the best possible performance, according to the operation conditions and designers’ requirements.

Addressing the urgent sustainability challenges in the wine industry, this study explores the efficacy of sustainability-oriented innovations (SOIs) and smart farming technologies (SFTs) across wine value chains in Cyprus and Italy. Employing KPIs for a rigorous assessment, the research delves into the environmental, economic, and social impacts of these technologies. In Cyprus (SIP7), the integration of digital labelling and smart farming solutions led to a substantial reduction in pesticide usage by up to 75% and enhanced the perceived quality of wine by an average of 8%. Italy's SIP10 witnessed a 33.4% decrease in greenhouse gas emissions, with an additional benefit of a 5.3% improvement in intrinsic product quality. Notably, SIP10 also introduced a carbon credit system, potentially generating an average annual revenue of €4,140 per farm. These findings highlight the transformative potential of SOIs and SFTs in promoting sustainable practices within the wine industry, demonstrating significant advancements in reducing environmental impact, improving product quality, and enhancing economic viability. The study underscores the critical role of innovative technologies in achieving sustainability goals and provides a compelling case for wider adoption within the agricultural sector.

A reduced order model is developed to monitor aeroengines condition (defining their degradation from a baseline state) in real-time, by using data collected in specific sensors. This reduced model is constructed by applying higher order singular value decomposition plus interpolation to appropriate data, organized in tensor form. Such data are obtained using a detailed engine model that takes the engine physics into account. Thus, the method synergically combines the advantages of data-driven (fast online operation) and model-based (the engine physics is accounted for) condition monitoring methods. Using this reduced order model as surrogate of the engine model, two gradient-like condition monitoring tools are constructed. The first tool is extremely fast and able to precisely compute `on the fly’ the turbine inlet temperature, which is a paramount parameter for the engine performance, operation, and maintenance, and can only be roughly estimated by the engine instrumentation in civil aviation. The second tool is not so fast (but still reasonably inexpensive) and precisely computes both, the engine degradation and the turbine inlet temperature at which sensors data have been acquired. These tools are robust in connection with random noise added to the sensors data and can be straight forwardly applied to other mechanical systems.

(1) In an era where sustainable behavior is increasingly crucial, understanding the discrepancy between individuals' sustainability-oriented values and their actual behaviors, known as the inner-outer gap, is vital. This study explores the potential of the Tripartite Structure of Sustainability (TSS) framework to address this gap within the context of sustainable education. By reviewing literature from the databases APA, ERIC, and Web of Science, we systematically examined factors influencing sustainable actions. (2) Employing a qualitative content analysis approach, we analyzed 56 articles over a 15-year period, identifying 83 factors that either bridge or reinforce the inner-outer gap. These factors were categorized within the TSS framework, which segments sustainability-oriented actions into individual, social, and self-transcendent domains, alongside their activation points: stable, situational, or automated. (3) Our analysis revealed that self-focused factors often reinforce the gap, suggesting a hindrance to sustainable behavior. Conversely, self-transcendent factors consistently bridged the gap, promoting sustainability. Social factors showed variable impacts based on the ethical and sustainable context they were placed in, suggesting that the social environment's orientation significantly influences sustainable behavior. (4) The study concludes that the TSS framework offers a promising approach to advancing sustainability in education by facilitating a paradigm shift towards holistic and interconnected perspectives. This shift is critical for fostering sustainable behaviors, thereby contributing to the field of educational psychology and offering practical implications for educators aiming to nurture a sustainable future.

Supermarkets in Port Harcourt (PH) city, Nigeria, predominantly rely on diesel electricity generation due to grid instability, leading to high cost of electricity prices. Although solar photovoltaic (PV) systems have been proposed as an alternative, these supermarkets have yet to adopt them, mainly due to high investment costs and a lack of awareness of the long-term financial and environmental benefits. This paper examines the technical and economic practicality of a PV system for these supermarkets using the PVsyst software and a spreadsheet model. Solar resources showed that PH has a daily average solar radiation and temperature of 4.21 kWh/m2/day and 25.73℃, respectively. Market Square, the supermarket with the highest peak power demand of 59.8 kW, and a 561 kWh/day load profile, was chosen as a case study. A proposed PV system with a power capacity of 232 kW, battery storage capacity of 34,021 Ah, a charge controller size of 100 A/560V, and an inverter with a power rating of 60V/75 kW has been designed to meet the load demand. The economic analysis showed a $266,936 life cycle cost, $0.12 per kWh levelized cost of electricity (LCOE), 4-year simple payback time, and a 20.5% internal rate of return (IRR). The PV system is feasible due to its positive net present value (NPV) of $165,322 and carbon savings of 582 tCO2/year.

Large values and gradients of stresses and deformations, triggering concentrations of stresses and deformations, arise in the corner areas of a structure. The action of forced deformations, leading to the finite rupture of the contact between the elements of a structure, also triggers the concentration of stresses, while the rupture reaches an irregular point, a line on the area boundary. The theoretical analysis of the stress-strain state (SSS) of areas with angular cutouts in the boundary under the action of discontinuous forced deformations is reduced to the study of singular solutions to the homogeneous problem of the elasticity theory that has power-related features. The calculation of stress concentration coefficients in the domain of a singular solution to the elastic problem makes no sense. It is experimentally proven that the zone, that is close to the vertex of the angular cutout in the area boundary, has substantial deformations, rotations, and it corresponds to rising values of the first and second derivatives of displacements along the radius in cases of sufficiently small radii in the neighbourhood of the irregular point of the boundary. For such areas, it is necessary to consider the plane problem of the elasticity theory, taking into account the geometric nonlinearity under the action of forced deformations. This will allow analyzing the effect of relations between orders of values of deformations, rotations, and forced deformations on the form of the equation of equilibrium. The purpose of this work is to analyze the effect of relations of deformation orders, rotations, forced deformations on the form of the equilibrium equation in the polar coordinate system for a V-shaped area under the action of forced temperature-induced deformations with regard for the geometrical non-linearity and physical linearity.

In the face of the upcoming 30th anniversary of econophysics, we review our contributions and other related works on the modeling of the long–range memory phenomenon in physical, economic, and other social complex systems. Our group has shown that the long–range memory phenomenon can be reproduced using various Markov processes, such as point processes, stochastic differential equations and agent–based models. Reproduced well enough to match other statistical properties of the financial markets, such as return and trading activity distributions and first–passage time distributions. Research has lead us to question whether the observed long–range memory is a result of actual long–range memory process or just a consequence of non–linearity of Markov processes. As our most recent result we discuss the long–range memory of the order flow data in the financial markets and other social systems from the perspective of the fractional Lèvy stable motion. We test widely used long-range memory estimators on discrete fractional Lèvy stable motion represented by the ARFIMA sample series. Our newly obtained results seem indicate that new estimators of self–similarity and long–range memory for analyzing systems with non–Gaussian distributions have to be developed.

Goals: To use visual logistics for interpreting COVID-19 molecular and rapid antigen test (RAgT) performance, determine prevalence boundaries where risk exceeds expectations, and evaluate benefits of recursive testing along home, community, and emergency spatial care paths. Methods: Mathematica/open access software helped graph relationships, compare performance patterns, and perform recursive computations. Results: Tiered sensitivity/specificity comprise: T1) 90%/95%; T2) 95%/97.5%; and T3) 100%/≥99%, respectively. In emergency medicine, median RAgT performance peaks at 13.2% prevalence, then falls below T1, generating risky prevalence boundaries. RAgTs in pediatric ERs/EDs parallel this pattern with asymptomatic worse than symptomatic performance. In communities, RAgTs display large uncertainty with median prevalence boundary of 14.8% for 1/20 missed diagnoses, and at prevalence >33.3-36.9% risk 10% false omissions for symptomatic subjects. Recursive testing improves home RAgT performance. Home molecular tests elevate performance above T1, but lack adequate validation. Conclusions: Widespread RAgT availability encourages self-testing. Asymptomatic RAgT and PCR-based saliva testing present the highest chance of missed diagnoses. Home testing twice, once just before mingling, and molecular-based self-testing help avoid false omissions. Community and ER/ED RAgTs can identify contagiousness in low prevalence (<22%). Real-world trials of performance, cost-effectiveness, and public health impact could identify home molecular diagnostics as the optimal diagnostic portal.

We introduce the Transformation Flower Approach (TFA), a Theory of Change that attends to multiple value creation and institutional change as a dual design challenge. We highlight how the TFA integrates social scientific theories and models relevant for transformative change (in particular focusing on pathways, leverage points, governance, power, and values) and demonstrate its practical value by an application to the ongoing transformation of the Dutch food system. By providing a holistic, transdisciplinary and practically relevant approach that aims to support new social contract formation, the TFA goes beyond other transformative change approaches. Based on the notion of pathways, it offers a toolbox that aids in working towards desired futures, involving both incumbents and challengers in an effort to harness untapped yet proximal potentials in a forward-looking way. By embracing an innovation approach, it not only promises to circumvent resistance to change, but also serves as a step-by-step approach to identify options for multiple value creation and effective cooperation. We demonstrate the analytical and practical value of the TFA by discussing action perspectives at various levels and scales in the context of the Dutch food system transition, including (1) area-oriented approaches, (2) acceleration agendas for specific transformation pathways, and (3) actor-specific transformation flowers. In developing these, we emphasize the importance of interdependencies between leverage points. Our approach helps to identify opportunities to link transformative options (the what), actors (the who) and levers (the how) in dynamic interaction to embark on transformative pathways.

The affinity constant, also known as the equilibrium constant, binding constant, equilibrium association constant, or the reciprocal value, the equilibrium dissociation constant (K_d), can be considered as one of the most important characteristics for any antibody-antigen pair. Many methods based on different technologies have been proposed and used to determine this value. However, since a very large number of publications and commercial datasheets do not include this information, significant obstacles in performing such measurements seem to exist. In other cases where such data are reported, the results have often proved to be unreliable. This situation may indicate that most of the technologies available today require a high level of expertise that does not seem to be available in many laboratories. In this paper, we present a simple approach based on standard immunoassay technology that is easy and quick to perform. It relies on the effect that the molar IC₅₀ approaches the K_d value in the case of infinitely small concentrations of the reagent concentrations. A two-dimensional dilution of the reagents leads to an asymptotic convergence to K_d. The approach has some similarity to the well-known checkerboard titration used for the optimization of immunoassays. A well-known antibody against the FLAG peptide, clone M2, was used as a model system and the results were compared with other methods. This approach could be used in any case where a competitive assay is available or can be developed. The determination of an affinity constant should belong to the crucial parameters in any quality control of antibody-related products and assays and should be mandatory in papers using immunochemical protocols.

Synthetic Aperture RADAR (SAR) is a radar imaging technique in which the relative motion of the sensor is used to synthesize a very long antenna and obtain high spatial resolution. Standard SAR raw data processing techniques assume uniform motion of the satellite (or aerial vehicle) and a fixed antenna beam pointing sideway orthogonally to the motion path, assumed rectilinear. Despite SAR data processing is a well established imaging technology that has become fundamental in several fields and applications, in this paper a novel approach has been used to exploit coherent illumination, demonstrating the possibility of extracting a large part of the ancillary data information from the raw data itself, to be used in the focusing procedure. In this work an effort has been carried out to try to focus the raw SAR complex data matrix without the knowledge of anyof the parameters needed in standard focusing procedures as Range Doppler (RD) algorithm, ω - K algorithm and Chirp Scaling (CS) algorithm. All the literature references regarding the algorithms needed to obtain a precise image from raw data use such parameters that refer both to the SAR system acquisition geometry and its radiometric specific parameters. In [12], authors introduced a preliminary work dealing with this problem and able to obtain, in the presence of a strong point scatterer in the observed scene, good quality images, if compared to the standard processing techniques. In this work the proposed technique is described and performances parameters are extracted to compare the proposed approach to RD.