The high thrust linear motor used for electromagnetic launch is switched with the anti-shunt thyristor as the switch. During the switching process, different current path states will appear, which will lead to changes in motor parameters and current fluctuation. Aiming at the air-core synchronous linear motor with parallel and series power supply, this paper analyzes the change of current path caused by the change of trigger signal of anti-parallel thyristor in the process of sectionalized stator switching. The motor circuit model of the switching process is derived. A new sectionalized stator switching method is proposed to realize the smooth switching of the sectionalized stator powered linear motor. Finally, the correctness of the analysis and modeling is verified by simulation, and the effectiveness of the sectionalized stator switching method is tested by using the test prototype.

Software quantum simulators are the most accessible tools for designing and testing quantum algorithms. This paper presents a comprehensive approach to building a software-based quantum simulator based on classical computing architectures. We explore fundamental quantum computing concepts, including state vector representations, quantum gates, and memory management techniques. The simulator prototype implements various memory optimization strategies, such as full-state representation, dynamic state pruning, and shared memory parallelization with OpenMP and distributed memory models using MPI. Additionally, data compression techniques, like ZFP, are explored to enhance simulation performance by reducing memory footprint. The results are validated through performance comparisons with leading open-source quantum simulators, such as Intel-QS, QuEST, and qsim. Our findings highlight the trade-offs between computational overhead and memory efficiency. This demonstrates that a hybrid approach using distributed memory and compression offers the best scalability for simulating large quantum systems. This work provides a foundation for developing efficient quantum simulators supporting more complex quantum algorithms on classical hardware.

Bandsaw blades are typical band-shaped cutting tools characterized by low stiffness and micro-level cutting depth, resulting in distinct wear mechanisms compared to rigid cutting tools. In this study, the wear curve and wear mechanisms of bandsaw tooth during the bandsawing of Cr12MoV cold-working steel was investigated. The tool life was divided into two stages: a rapid wear stage (Stage I) and a homogeneous wear stage (Stage II). In Stage I, the wear was dominated by chipping although multiple wear mechanisms were found due to the relatively poor manufacturing accuracy compared to rigid cutting tools, which results in remarkable differences among the cutting depths of individual teeth. In Stage II, abrasive and adhesive wear were the primary wear mechanisms instead of chipping, which was related to the microstructure of Cr12MoV. Furthermore, methods for increasing the bandsaw performance were proposed based on the tooth wear mechanisms.

Real-time simulation of toxic gas dispersion is critical for emergency management in high-sulphur gas fields. The CALPUFF (California Puff model) gas dispersion model, a Lagrangian Gaussian Puff model, is often used in mountainous environments due to its ability to handle complex terrain and weather conditions. Verifying the accuracy of toxic gas dispersion simulations under mountainous conditions is vital for emergency response and rescue. In this article, CALPUFF and Computational Fluid Dynamics (CFD) gas dispersion modeling are compared, studying emissions from a hypothetical pipeline breakout accident in a mountainous area, focusing on range of Semi-Lethal Concentration (LC$_{50}$), Immediate Danger to Life and Health Concentration(IDLH). Thirteen groups of simulation conditions are set up for the experiment, including static wind and winds from the east(E), south(S), west(W), and north(N) at speeds of 1, 2, and 3$m/s$. Comparative experiments between CALPUFF and CFD models show consistent results, confirming the feasibility of CALPUFF for near-field moutainous applications. The overall dispersion range deviation between two methods under calm or light wind of N, E and W is about 300$m$. However,the simulation results of the CALPUFF model and the CFD model show significant differences in S wind. In CALPUFF simulation that the toxic gases are channeled by the valleys, while in the CFD model the toxic gases climb over the mountain top and continue to spread and extend towards the northern valley. The evaluation of CALPUFF’s suitability for applications in near-field mountainous environments indicates its potential use for high-sulfur gas fields and gas dispersion simulations in emergency scenarios.

Dynamic wireless charging (DWC) for electric vehicles (EVs) is gaining traction as a more accessible charging method, with the added benefits of extending vehicle range and reducing battery size. By providing a charging connection through the road surface, DWC offers an additional charging option without the need for a physical connection. This approach inherently links the charging load profile to the vehicle's movement relative to the charging pad(s), thus introducing more stochastic charging events to the grid. For dynamic wireless power transfer (DWPT), these events involve high instantaneous power and are short in duration. To better understand the impact of DWPT, accurate models are required to test control systems and potential solutions. Additionally, these systems require high-frequency simulation for wireless power transfer (WPT), which results in long simulation times during development. In this paper, a simplified model is presented to ensure the efficiency of grid-connected simulations and achieve a certain level of accuracy that reflects the internal dynamics of wireless charging. This model achieves a 30-fold reduction in simulation time with only a 6% deviation from the base model.

Homeostasis and its interaction with gene expression in the development and maintenance of living systems is discussed in order to formulate a new method to diagnose and treat diseases on this causative level. This includes an inquiry into the unsolved homeostasis problems of: location (where in the cell are calculations performed?), communication (what language used?), identity (set of plans/hierarchy of set points?) and computational (mechanisms used to make necessary adjustments?). As these functions require the processing of vast amounts of information which is communicated at every level of organization including the mechanisms of epigenetics, different computer models are discussed, with examples for each; analog, digital and the possibility of quantum biological. Each one allows certain properties and cell functions to emerge. The difference between functional homeostasis and dysfunctional homeostasis is discussed with strategies to indirectly study dysfunctional homeostasis in terms of epigenetic signatures. Hormesis is discussed as a mechanism to reverse the epimutations, leading to a method of treatment for almost any chronic disease. These topics are discussed as being a whole interconnected system.

For dental implant treatment to be successful, esthetics, functionality, and cleanability are all required of the superstructure, the final prosthesis. Screw fixation and cementation have been the conventional methods of choice for the crown prosthesis of implants, but these individual methods cannot fulfill all the requirements. As a solution to this problem, we have devised a new implant superstructure restoration method (inlay covering esthetic technique) using computer-aided design / computer-aided manufacturing inlays. This involves the placement of an inlay covering the access hole in a highly translucent partially stabilized zirconia crown. This technique expands the indications for implant treatment and improves the oral quality of life of patients.

Research on high-volume fly ash concrete, which utilizes large quantities of fly ash, has been actively conducted to promote resource recycling and reduce carbon dioxide emissions. However, while cement mixed with fly ash exhibits different temperature sensitivities compared to traditional cement, its hydration and mechanical properties vary depending on curing conditions. Despite this, there is a significant gap in research on this topic. In this study, high-volume fly ash concrete was produced with fly ash replacement rates of 35 % and 55 %. Compression strength tests were performed at various curing ages under three different curing temperature conditions, and the results were analyzed. Additionally, an isothermal calorimeter was used to analyze hydration characteristics under different curing conditions. The results indicated that concrete with high fly ash content was more sensitive to curing temperature compared to ordinary Portland cement.

Train fault detection primarily relies on the comparative analysis of collected images with standard reference images, making the accurate identification of the collected image types crucial for effective fault detection. Most current systems achieve indirect classification of carriage images by using Automatic Equipment Identification (AEI) devices to recognize carriage identification number information while capturing the carriage images. However, damaged RF tags or blurred characters can hinder these devices, obstructing further train fault analyses. The unique features of carriage linear array images, such as high resolution, extreme aspect ratios, and local non-linear distortions, pose significant challenges to recognition algorithms. This paper proposes a method specifically designed to recognize these types of images. First, we implement an object detection algorithm to locate the positions of key components in carriage linear array images. By leveraging the spatial layout mapping between these key components and the carriage type classification, we simplify the complex image recognition problem into a sparse point set alignment task. To ensure effective registration despite local distortions in the linear array images, we propose a weighted radial basis function. To address the issues of unknown matching relationships and quantity mismatches during point set alignment, the proposed objective function is designed to maximize the similarity between Gaussian mixtures of point sets, thereby determining the RBF weights. Extensive experiments have demonstrated that our algorithm achieves 100% recognition accuracy under local nonlinear scale distortions of less than 15%. The algorithm remains effective even in the presence of some false positives or missed detections in key component object detection results. It can accurately identify the target category from 79 image categories within 24 milliseconds on an i7 CPU without GPU support. It is of great significance to reduce system cost and promote automatic exterior fault detection for train rolling stock.

The composition simplex (N, P, K, Ca, and Mg) of the leaf is the main scores used by different approaches like the Diagnosis and Recommendation Integrated System and Compositional Nutrient Diagnosis to study the nutrient interactions and balance in plant leaves. However, the application and validation of these concepts to grain composition remains unexplored. Contrary to foliar analysis's early intervention for nutrient deficiency detection and correction, applying this approach to seeds assesses diverse cultivars' potential, enabling anticipation of their adaptation to climate conditions and informed selection for future crops. In the present study, a collected database of more than 924 scores including the grain yield (kg ha-1) and the nutrient composition (mg kg-1) of different corn varieties is used to develop a novel nutrient-based diagnostic approach to identify reliable markers of nutrient imbalance. A 'nutrient signature' model is proposed based on the impact of the environ-mental conditions on the nutrient indices and composition (N, P, K, Ca, and Mg) of the corn grains. The yield threshold used to differentiate between low and high-yielding subpopulations is established at 12.000 kg ha-1and the global nutrient imbalance index (GNII) of 2.2 is determined using the chi-square distribution function and vali-dated by the Cate-Nelson partitioning method, which correlated yield data distribution with the GNII. Therefore, the nutrient compositions were classified into highly balanced (GNII ≤ 1.6), balanced (1.6 < GNII ≤ 2.2), and imbalanced (GNII > 2.2). In addition, we found that the Xgboost model's predictive accuracy for GNII is signif-icantly affected by soil pH, organic matter, and rainfall. These results pave the way for adapted agricultural practices by providing insights into the nutrient dynamics of corn grains under varying environmental conditions.

Previous research has indicated that ultra-high pressure (UHP) technology is useful in speeding up the extraction process of cold brew (CB) coffee. However, the impact of different degrees of roasting on UHP CB coffee is still unclear. Therefore, this study aimed to investigate the effects of three different degrees of roasting (light, medium, and dark) on the physicochemical and flavor characteristics of UHP CB coffee. The results of this study showed that most physicochemical characteristics of UHP coffee were similar to those of conventional CB coffee, regardless of the degree of roasting. However, the majority of physicochemical characteristics, non-volatile components, and sensory evaluation significantly increased with an increase in roasting degree. The HS-SPME-GC/MS analysis showed that most volatile components, such as pyrazines, furans (except furfural), esters, pyrrole, pyridine, and most aldehydes, increased from light to dark roasting, and this was significantly evident in CB coffee compared with UHP. The content of volatile components in UHP coffee was significantly (P<0.05) higher than that in CB coffee at the same degree of roasting, especially with dark roasting. The combination of orthogonal partial least squares-discriminant analysis (OPLS-DA) and principal component analysis (PCA) indicated that the distance between coffee samples at different degrees of roasting under CB coffee was greater than that under UHP coffee. However, the distance between these two extraction methods at medium roasting was evidently closer than that at light and dark roasting. Moreover, 15 representative differential compounds, such as were Hazelnut pyrazine, linalool, butane-2,3-dione, 3- methylbutanal found by the calculation of odor-active values (OAVs) indicating the main contributing compounds to odor. Overall, the effect of roasting degrees on UHP coffee was less than that on CB coffee, which was consistent with the results of physicochemical characteristics, volatile components, and sensory evaluation.

Olivine-like NaFePO4 glasses and nanocomposites are promising materials for cathodes in sodium batteries. Our previous study concerned the influence of high pressure on DC electric conductivity of NaFePO4 glasses. This work presents the results of AC measurements of glasses and nanocomposites from pressure treatment. Depending on the temperature range, the electronic conduction mechanism changed from variable range hopping (between Fe2+/Fe3+centers) to phonon-assisted hopping. For DC electric conductivity the portrayal via the classic Mott’s Variable Range Hopping is limited to low temperatures. Spectra of AC conductivity for glasses and pressure-formed nanocomposites fulfill Jonscher’s scaling law with power exponents ranging from 0.3 to 0.9 depending on temperature and the electron hopping mechanism. Due to the decrease in distance between hopping centers, an increase of AC conductivity around 2-3 orders of magnitude was observed after high pressure-high temperature treatment. Up to 200 K temperature dependencies of AC conductivity follow the pattern suggested by Mott's theory. Above that temperature corresponds to phonon-assisted hopping with activation energies EAC≈0.40 eV (for glass: amorphous solid) and EAC≈0.18 eV (for glass + nanocrystallites nanocomposite). Notable that they are considerably lower than values of EDC for DC conductivity. Results obtained show that high-temperature compressing, just below the glass temperature, significantly leads to a stable decrease in distance between hopping centers related to nanocrystallites in a glassy matrix. Consequently, it leads to an essential rise in electric conductivity and volumetric capacity. AC spectra of electronic conductivity are disturbed by the conduction of Na+ mobile ions, which impacts polaron conductivity and can be a limiting factor for conductivity.

The minimum ignition energy (MIE) has been extensively studied via experiments and simulations. However, our literature review reveals little quantitative consistency, with results varying for f=1.0 from 0.324 to 1.349 mJ, and for f=0.9 from 0.22 to 0.944 mJ. Therefore, there is a need to resolve these discrepancies. This RANS study aims to partially address this knowledge gap. Additionally, it presents other flame evolution parameters essential for robust combustion design. Using the reactingFOAM solver we predict the threshold energy required to ignite the fuel mixture. For this, the single step using the Arrhenius law is selected to model ignition in the flame kernel of stochiometric and lean CH₄/air mixtures, allowing it to develop into a self-sustained flame. The ignition power density, an energy quantity normalised with volume is incrementally varied keeping the kernel critical radius r_s constant 0.5 mm in the quiescent mixture of two equivalence ratios fs 0.9, and 1.0, for varied operating pressures 1, 5 and 10 bar at constant initial temperature 300 K. The minimum ignition energy is validated with twelve independent 1 bar data sets both numerical and experiments. Finally, a mathematical formulation of MIE is devised, a function of pressure and equivalence ratio shows a slightly curved relationship.

High-grade advanced ovarian, fallopian tube and primary peritoneal (HGAOC) cancer are malignancies in which, apart from surgical treatment, systemic treatment plays an important role. The improvement in treatment results is associated with the introduction of polyADP-ribose polymerase inhibitors (PARPis). The aim of this study is to present a cross-section of patients treated for HGAOC, in one center, including the distribution of treatment principles following the most up-to-date guidelines. We observed patients who reported to the Department of Gyneacological Oncology between January 2018 and December 2023. We analyzed 437 women with a first diagnosis of HGAOC, who had not been treated before. The introduction of combined treatment with bevacizumab and PARPi into the first line of treatment, regardless of any remnants left during cytoreductive surgery, was introduced in November 2022. Since then, 30% (18/60) of patients (14 with olaparib and 4 with niraparib) have used the above regimen. Previously, in May 2021 - October 2022, it was 27% of patients (13/81 with olaparib and 9/81 with niraparib). Among patients starting treatment in January 2018 - April 2021, only 4.7% (5/106) received the platinum + paclitaxel + olaparib regimen. In both groups – with and without BRCA1/2 pathogenic or likely- pathogenic variant, significantly more patients used PC + PARPi or PC + BEV + PARPi in periods II and III than in period I (p<0.01). The introduction of modern treatment in our center very quickly changed the structure of patient treatment. Carriers of BRCA1/2 pathogenic or likely-pathogenic variant had previously received only chemotherapy, disappeared after the introduction of PARPi, in favor of new therapies. Most patients with no BRCA1/2 pathogenic or likely-pathogenic variant, who used PARPi in therapy in our center – received niraparib and therefore they are beneficiaries of molecular diagnostics in the field of HRD.

Knee joint injuries, including those affecting the anterior cruciate ligament (ACL), meniscus, and cartilage, present complex challenges in sports medicine and orthopedics due to the intricate cellular and molecular mechanisms involved in tissue damage and repair. Understanding the molecular biology underpinning these processes is crucial for developing effective therapeutic and rehabilitation strategies. This systematic review investigates the impact of mechanical loading on the cellular responses during knee joint injury repair, with a particular focus on the molecular pathways involved in tissue regeneration. Mechanical loading plays a dual role, where controlled early loading can promote tissue repair, while excessive or inappropriate loading can exacerbate tissue damage. Fibroblasts, chondrocytes, and mesenchymal stem cells (MSCs) are central to the repair process, and their activation, proliferation, and differentiation are regulated by key molecular pathways. Upon injury, mechanotransduction pathways such as the integrin/FAK signaling axis are activated, which convert mechanical signals into biochemical responses that regulate cell adhesion, migration, and extracellular matrix (ECM) synthesis. Additionally, mechanosensitive ion channels like Piezo1 and TRPV4 modulate intracellular calcium levels, triggering downstream signaling cascades such as calmodulin/CaMKII, which regulate gene transcription and cellular responses to mechanical stress. The YAP/TAZ pathway, a critical component of the Hippo signaling pathway, responds to mechanical stimuli and regulates cell proliferation and ECM production in fibroblasts and chondrocytes. YAP/TAZ translocate to the nucleus in response to mechanical loading, where they interact with transcription factors such as TEAD, promoting the expression of genes involved in collagen synthesis and tissue repair. In parallel, growth factors like transforming growth factor-beta (TGF-β) and fibroblast growth factor (FGF) activate the TGF-β/Smad and PI3K/Akt signaling pathways, driving MSC differentiation into fibroblasts and chondrocytes, essential for ligament and cartilage repair. Mechanical loading also influences the inflammatory response at the injury site by modulating immune cell activity. Early mechanical loading can shift macrophages from a pro-inflammatory M1 phenotype to an anti-inflammatory M2 phenotype, mediated by growth factors such as TGF-β and interleukin-10 (IL-10). This phenotypic switch promotes tissue regeneration by enhancing ECM synthesis and resolving inflammation, which is crucial for long-term joint health. Matrix metalloproteinases (MMPs), regulated by NF-κB and MAPK pathways, play a role in ECM remodeling, where an imbalance between MMPs and their inhibitors (TIMPs) can lead to excessive matrix degradation, impeding tissue repair. Furthermore, Wnt/β-catenin signaling is activated in response to moderate mechanical loading, promoting chondrocyte proliferation and enhancing cartilage repair by upregulating type II collagen and aggrecan synthesis. However, dysregulation of Wnt signaling under excessive mechanical stress can lead to chondrocyte hypertrophy and cartilage degradation, contributing to osteoarthritis development. This review also explores emerging therapeutic strategies that leverage the molecular biology of knee joint repair, including biologics like platelet-rich plasma (PRP) and MSC-derived exosomes, which deliver bioactive molecules that activate critical regenerative pathways such as TGF-β/Smad and PI3K/Akt. Gene therapies targeting Wnt signaling or YAP/TAZ offer potential for enhancing tissue regeneration by modulating mechanotransduction and repair processes at the molecular level. In conclusion, the molecular biology of cellular responses to mechanical loading is central to knee joint repair following injuries. By understanding these processes and targeting specific molecular pathways, clinicians can optimize rehabilitation protocols and develop novel therapeutic approaches that enhance tissue regeneration, prevent chronic degeneration, and restore joint function. This comprehensive synthesis highlights the importance of integrating molecular insights into treatment strategies for ACL, meniscal, and cartilage injuries to improve patient outcomes.

Cutaneous metastatic melanoma (CMM) is the most aggressive form of skin cancer with a poor prognosis. Drugs-induced secondary tumorigenesis and the emergency of drug resistance worsen the already worrying scenario, thus rendering urgent the development of new treatments, not dealing with mutable cellular processes. Triphenyl phosphonium salts (TPPSs), in addiction to act as cytoplasmic membrane disruptors, are reported to be mitochondria-targeting compounds, exerting anticancer effects mainly by damaging their membranes and causing depolarization, impairing mitochondria functions and their DNA, triggering oxidative stress (OS), and priming primarily apoptotic cell death. TPP-based bola-amphiphiles are capable to self-form nanoparticles (NPs) with enhanced biological properties, as commonly observed for nanomaterials. Already employed in several other biomedical applications, only recently the per se selective potent antibacterial effects of a TPP bola-amphiphile has been demonstrated on 50 multidrug resistant (MDR) clinical superbugs, as well as its exceptional and selective anticancer properties, on sensitive and MDR neuroblastoma cells. Here, aiming at finding new molecules possibly developable as new treatments for counteracting CMM, the effects of this TPP-based bola-amphiphile (BPPB) have been investigated against two BRAF mutants CMM cell lines (MeOV and MeTRAV) with excellent results (even IC50 = 49 nM on MeOV after 72 h treatment). Upon these findings and considered the low cytotoxicity of BPPB against different mammalian not tumoral cell lines and red blood cells (RBCs, selectivity indexes up to 299 on MeOV after 72 h treatment), the possible future development of BPPB as topical treatment for CMM lesions was presumed. In this sight, a biodegradable hyaluronic acid (HA)-based hydrogel formulation (HA-BPPB-HG) was prepared without using any potentially toxic crosslinking agents, but simply dispersing suitable amounts of the two ingredients in water and sonicating under gentle heating. HA-BPPB-HA was completely characterized with promising outcomes, such as high swelling capability, high porosity and viscous elastic rheological behavior.

The zinc oxide (ZnO) arrester is positioned on locomotive roof preventing other onboard electrical equipment from the harm caused by external and internal overvoltages. A number of locomotive arrester burnout and explosion accidents occur during traction supply network harmonic resonance causing train stoppages and power outages in the network. This study firstly carries out high-frequency tests to investigate the wide frequency band electrical characteristics of the locomotive arrester, explaining that the arrester is prone to fault during resonance. Consequently, a prognostics and health management (PHM) for locomotive arrester is proposed providing on online monitoring, fault warning and health assessment solutions, which is beneficial to the operation and maintenance of arresters in the future. The testing method and PHM scheme presented in this paper can be not only applied to the arrester, also readily expanded to other high-voltage electrical equipment on the electric locomotive.

To investigate the composition of caproic acid-producing bacterial communities in sub-high-temperature Daqu, we analyzed four different Daqu samples from Sichuan. After enriching the samples with a specialized medium, we performed high-throughput sequencing of 16S rRNA gene amplicons on the metagenomic DNA from both the Daqu samples and the enrichment cultures. Our analysis focused on identifying and characterizing the caproic acid-producing bacterial communities present in Daqu. The results revealed that enrichment increased both the diversity and abundance of potential caproic acid-producing bacteria in Daqu. The predominant caproic acid-producing bacteria, with a relative abundance greater than 1%, included Clostridium sensu stricto 18 (2.19% to 69.00%), Clostridium sensu stricto 15 (1.76% to 7.65%), as well as smaller amounts of Clostridium sensu stricto 12, Clostridium sensu stricto 1, Clostridium sensu stricto 10, Clostridium sensu stricto 7, and Caproiciproducens. Specifically, Q1 Daqu was characterized by the presence of Clostridium sensu stricto 18 and Clostridium sensu stricto 15. Q2 Daqu featured Clostridium sensu stricto 1, Caproiciproducens, and Clostridium sensu stricto 18. Q3 Daqu included Clostridium sensu stricto 18 and Caproiciproducens. Q4 Daqu contained Clostridium sensu stricto 18 and Clostridium sensu stricto 1. These findings indicate that there are variations in the composition of caproic acid-producing bacterial communities among different sub-high-temperature Daqu samples from Sichuan. This preliminary analysis provides a theoretical basis for further studies on caproic acid bacteria in Daqu and offers insights into the development of high-quality Daqu, which may enhance the quality of Nongxiangxing liquor.

Dielectric Elastomer Actuators (DEAs) are emerging as promising candidates for various applica-tions in robotics and optical devices due to their lightweight, miniaturization potential, high en-ergy density, simple structure, and low power consumption. However, their effective actuation always demands sophisticated high-voltage driving circuits that are compact and responsive. DEAs need to be capable of generating intricate high-voltage waveforms or simultaneously con-trolling multiple channels with distinct high-voltage levels. This paper proposes a high-voltage power supply for DEAs, featuring a four-channel high-voltage driving circuit. The circuit is ca-pable of independently generating high-voltage signals ranging from 100 V to 6000 V and can be programmed to produce arbitrary waveforms with adjustable frequencies. The independent op-eration of channels without crosstalk showcases the system's integration and potential for cross-disciplinary applications.

The study of the morphology, thermal, and chemical stability of the fluorinated compounds was performed using Becke’s three-parameter hybrid functional approach with the correlation provided by Lee, Yang, and Parr and the cc-pVTZ basis set aiming to design low sensitivity, toxicity, instability, and proneness to decomposition or degradation over a short time high-energy materials. The most stable conformers of the compounds under study were selected based on their total energy. Their thermal and chemical stability was evaluated based on the binding energy per atom, chemical hardness, and softness. The oxygen-fluorine balance is assessed to evaluate the sensitivity of these new materials. The density, detonation pressure, and velocity of the selected conformers were theoretically obtained to reveal the influence of -CF3, -OCF3, and cyclic -O(CF2)nO- fragments on the energetic properties of nitroaromatics as well as their stability and resistance to shock stimuli. The results allow us to predict new multipurpose energetic materials with a good balance between power and stability. Referring to the results obtained, we recommend CF3N2, OCF3N2, C2F6N2, 1CF2N2/O2CF2N2, and 2CF4N2/O2C2F4N2 for practical usage because these compounds possess greater stability compared to tetryl and better explosive properties than TNT.

BACKGROUND: Qu-aroma is a critical quality indicator for medium-high temperature Daqu (MT-Daqu), significantly influencing the aroma profile of strong-aroma Baijiu (SAB). SAB is produced across various regions in China, each with unique environmental conditions and production techniques. These regional differences are likely to cause variations in the Qu-aroma of MT-Daqu. Despite this, comprehensive research on the variations in Qu-aroma across different regions has been lacking. This study aims to address this gap by utilizing Gas Chromatography-Olfactometry-Mass Spectrometry (GC-O-MS) and electronic nose (E-nose) technology, combined with sensory evaluation, to analyze the differences in Qu-aroma characteristics and volatile compound profiles of MT-Daqu from seven distinct production areas.RESULTS: Sensory analysis identified seven broad aroma categories and 25 specific aromas characterizing the Qu-aroma of MT-Daqu samples. Chen aroma and roasted aroma were notably more prevalent in MT-Daqu samples from Sichuan compared to those from other regions (P < 0.05), while the fermentation aroma was less prominent in Sichuan samples. In total, 123 volatile compounds were detected in MT-Daqu, with 46 classified as aroma-active compounds. Among these, 21 aroma-active compounds were identified as markers distinguishing Sichuan MT-Daqu from those produced in non-Sichuan regions, showing significant differences in their concentrations (P < 0.05). Additionally, six major aroma-active compounds-ethyl isovalerate, ethyl heptanoate, hexanal, 1-nonanal, (E)-2,4-decadienal, and 2,3-dimethyl-5-ethylpyrazine-were found to significantly contribute to the aroma differences between Sichuan and non-Sichuan MT-Daqu.CONCLUSION: This study delineates the distinct Qu-aroma characteristics of MT-Daqu from various SAB production areas and identifies the aroma-active compounds responsible for these differences. The insights gained from this research offer valuable guidance for optimizing flavor profiles in MT-Daqu production, potentially enhancing the overall quality and regional distinctiveness of the product.

The growth of photosynthetic organisms requires specific ranges of temperature and photosynthetically active radiation that are technically difficult to achieve and control, especially in outdoors cultures. In such cases, a typical meteorological sequence can be a useful tool to estimate the growth of photosynthetic organisms. This work proposes a new methodology based on long-term meteorological sequences to simulate the growth of photosynthetic organisms. A case of study that addresses the simulation of the growth of microalgae (Chlorella vulgaris) in Riosequillo, north of the Madrid region (Spain), is shown for the four seasons of the year, and these estimates are then compared with the observed results of an experimental microalgae culture in domestic wastewater. The results also show great agreement with the probability distribution function of the biomass concentration per day, obtaining the best results for typical meteorological sequences of summer and spring. The methodology seems to confirm the representativeness of typical meteorological sequences and also allows the identification of the most likely production scenarios for the feasibility analysis of projects, which has potential application in decision-making processes.

We extensively studied serigraphic screen-printed commercial silver flake inks loaded with silicon inclusions in order to achieve pinning at the grain boundaries. Based on grain size measurements using electron backscattered diffraction (EBSD), commercial silver ink with silicon microparticle content of 5 wt.% shows a significant grain growth retardation compared to the pristine silver ink, which stabilizes electrical conductivity up to 700 ◦C via Zener pinning mechanism. The modified silicon-loaded silver ink experiences a two times increase in grain size when heated up to 700 ◦C, compared to a seven times increase for the pristine silver ink. In turn, this enables operation temperatures significantly higher than the conventional operational window of microparticle-based silver inks, which are usually limited to 400 ◦C. Using isothermal exposures of 10 minutes up to 4 hours this phenomenon is observed at temperatures ranging from 250 ◦C to 900 ◦C. The electrical conductivity stability, grain size evolution and oxide contents were studied up to 4 hours. The activation energy of silver ink with silicon inclusions is 54% lower than for the pristine silver ink due to pining effect, which retards grain growth via the Zener mechanism. Most importantly, the electrical resistivity becomes stable up to 700 ◦C, which is more than twice the operation limit for off-the-shelf screen-printable silver flake inks. Hence, we demonstrate that adding controlled amounts of silicon particles to silver inks towards grain structure engineering can open new vistas of possibilities for screen-printed metallic inks.

The majority of structures supporting solar panels are founded on thin-walled metal piles driven into the ground to optimize costs and construction timelines. These pile foundations are subjected to repetitive lateral loads from various external forces, such as wind, which can compromise the in-tegrity of the pile-soil system. Given that the proper functioning of photovoltaic solar plants is typically expected for 20-30 years, predicting their useful life under fatigue loading becomes crucial. This research investigates the lateral load response of a single pile subjected to different fatigue loads in stiff cohesive soils. Additionally, the effect of loading cycles on the degradation of pile-soil ad-hesion is studied through pull-out field tests. This study reveals that soil fatigue does not occur under repetitive loading, and the soil’s stiffness remains constant once the cycles causing soil compaction have been overcome. Nevertheless, the soil's accumulated plastic deflection steadily increases once soil compaction due to cyclic loading occurs. The implications of these results on the fatigue life of photovoltaic solar panel foundations are discussed.

Tefluthrin (Tef) is categorized as a type-I pyrethroid insecticide, telmisartan (Tel) functions as an angiotensin II receptor blocker, and KB-R7943 was identified as an inhibitor of Na+-Ca2+ exchange process. However, the influence of these compounds on the amplitude and gating properties of voltage-gated Na+ current (INa) in neurons associated with pain signaling remains unclear. In cultured dorsal root ganglion (DRG) neurons, whole-cell current recordings revealed that Tef or Tel increased the peak amplitude of INa, concomitant with an elevation in the time constant of INa inactivation, particularly in the slow component. Conversely, exposure to KB-R7943 resulted in a depression in INa, coupled with a decrease in the slow component of the inactivation time constant of INa. Theoretical simulations and bifurcation analyses were performed on a modeled interneuron in the spinal dorsal horn. The occurrence of INa inactivation accentuated the subthreshold oscillations (SO) in the membrane potential. With an increase in applied current, SO became more pronounced, accompanied by the emergence of high-frequency spiking (HF) with a frequency of approximately 150 Hz. Moreover, an elevation in INa conductance further intensified both SO and HF. Consequently, through experimental and in silico studies, this work reflects that Tef, Tel, or KB-R7943 significantly impacts the magnitude and gating properties of INa in neurons associated with pain signaling. The alterations in INa magnitude and gating in these neurons suggest a close relationship with pain transmission.

Developing new antibiotics poses a significant challenge in the fight against antimicrobial resistance (AMR), a critical global health threat responsible for approximately 5 million deaths annually. Finding new classes of antibiotics that are safe, have acceptable pharmacokinetic properties, and are appropriately active against pathogens is a lengthy and expensive process. Therefore, high-throughput platforms are needed to screen large libraries of synthetic and natural compounds. In this review, we present bacterial cytological profiling (BCP) as a rapid, scalable, and cost-effective method for identifying the mechanisms of action of antibiotics, offering a promising tool for combating AMR and drug discovery. We present the application of BCP for different bacterial organisms and different classes of antibiotics and discuss BCP's advantages, limitations, and potential improvements. Furthermore, we highlight the studies that have utilized BCP to investigate pathogens listed in the Bacterial Priority Pathogens List 2024 and we identify the pathogens whose cytological profiles are missing. Lastly, we explore the most recent artificial intelligence and deep learning techniques that could enhance the analysis of data generated by BCP, potentially advancing our understanding of antibiotic resistance mechanisms and the discovery of novel druggable pathways.

Digital image compression is applied to reduce camera bandwidth and storage requirements, but real-time lossless compression on a high-speed high-resolution camera is a challenging task. The article presents hardware implementation of a Bayer colour filter array lossless image compression algorithm on an FPGA-based camera. The compression algorithm reduces colour and spatial redundancy and employs Golomb-Rice entropy coding. A rule limiting the maximum code length is introduced for the edge cases. The proposed algorithm is based on integer operators for efficient hardware implementation. The algorithm is first verified as a C++ model and later implemented on Xillinx Zynq UltraScale+ device using VHDL. An effective tree-like pipeline structure is proposed to concatenate codes of compressed pixel data to generate a bitstream representing data of 16 parallel pixels. The proposed parallel compression achieves up to 56% reduction in image size for high resolution images. Pipelined implementation without any state machine ensures operating frequencies up to 320 MHz. Parallelised operation on 16 pixels effectively increases data throughput to 40 Gbit/s while keeping total memory requirements low due to real-time processing.

Carbon fiber-reinforced polymer (CFRP), noted for its outstanding properties including high specific strength and superior fatigue resistance, is increasingly employed in aerospace and other demanding applications. This study investigates the interactions between CFRP composites and high-energy lasers (HEL), with continuous wave laser powers reaching up to 120 kW. A novel automated sample exchange system, operated by a robotic arm, minimizes human exposure while enabling a sequence of targeted laser tests. High-speed imaging captures the rapid expansion of a plume consisting of hot gases and dust particles during the experiment. The research significantly advances empirical models by systematically examining the relationship between laser power, perforation times, and ablation rates. It demonstrates scalable predictions for the effects of high-energy laser radiation. Detailed examination of the damaged samples, both visually and via micro-focused computed X-ray tomography, offers insights into heat distribution and ablation dynamics, highlighting the anisotropic thermal properties of CFRP. Compression-after-impact (CAI) tests further assess the residual strength of the irradiated samples, enhancing the understanding of CFRP’s structural integrity post-irradiation. Collectively, these tests improve the knowledge of the thermal and mechanical behavior of CFRP under extreme irradiation conditions. The findings not only contribute to predictive modeling of CFRP's response to laser irradiation but also enhance the scalability of these models to higher laser powers, providing robust tools for predicting material behavior in high-performance settings.

Background/Objectives: Dental implants have become a cornerstone of restorative dentistry, providing a long-lasting method for tooth replacement. The level of osseointegration has a big impact on the biomechanical stability at the bone-implant contact (BIC), which determines how long these implants will work. However, the exact consequences of changing osseointegration levels on different implant designs, especially in bones with variable densities, are not well known. Three short dental implants were tested in this study: BioMet 3iT3, Straumann® Standard Plus Short Regular Neck (SPS-RN), and Straumann® Standard Plus Short-Wide Neck (SPS-WN). 3D finite element analysis (FEA) was used to look at how well they worked biomechanically. This paper tests the implants at four stages of osseointegration: 25%, 50%, 75%, and 100% in both high-density (Bone Type III) and low-density (Bone Type IV) cancellous bone. It also created and examined realistic CAD models under static occlusal loading conditions to assess stress distribution and major strains at the bone-implant contact.; Results: The study discovered that as osteointegration increases, von Mises stress and principal strains go down significantly for all implant types. The SPS-WN implant had the lowest strain values, especially for bone with low density. These reductions demonstrate increased mechanical stability as the bone-implant inter-face becomes more capable of dispersing mechanical stresses, minimizing the potential for localized deformation and bone resorption.; Conclusions: The results highlight the importance of achieving optimum osseointegration to reduce mechanical stress and increase the lifespan of dental implants. The SPS-WN type implant performed better in biomechanical tests than the others, especially when bone conditions were not ideal. This makes it a great choice for clinical applications that need long-term implant success.

Full depth precast deck panel (FDDP) is one element of the prefabricated bridge element and systems (PBES) that allows for quick un-shored assembly of the bridge deck on-site as part of the accelerated bridge construction (ABC) technology. This paper investigates the structural response of full-depth precast deck panels (FDDPs) constructed with new construction materials and connection details. FDDP is cast with normal strength concrete (NSC) and reinforced with high modulus (HM) glass fiber reinforced polymer (GFRP) ribbed bars. The panel-to-girder V-shape connections use the shear pockets to accommodate the clustering of the shear connectors. A novel transverse connection between panels has been developed, featuring three distinct female-to-female joint configurations, each with 175-mm projected GFRP bars extending from the FDDP into the closure strip, complemented by a female vertical shear key and filled with cementitious materials. The ultra-high performance fiber reinforced concrete (UHPFRC) was selectively used to joint-fill the 200-mm transverse joint between adjacent precast panels and the shear pockets connecting the panels to the supporting girders to ensure full shear interaction. Two actual-size FDDP specimens for each type of the three developed joints were erected to perform fatigue tests under the footprint of the Canadian Highway Bridge Design Code (CHBDC) truck wheel loading. The FDDP had a 200-mm thickness, 2500-mm width, and 2400-mm length in traffic direction; the rest was over braced steel twin girders. Two types of fatigue tests were performed; incremental variable amplitude fatigue (VAF) loading and constant amplitude fatigue (CAF) loading, followed by monotonically loading the slab ultimate-to-collapse. It was observed that fatigue test results showed that the ultimate capacity of the slab under VAF loading or after 4 million cycles of CAF exceeds the factored design wheel load specified into the CHBDC. Also, punching shear failure mode was dominant in all the tested FDDP specimens.

Fungi play important roles in the process of material cycling and energy transfers in aquatic ecosystems. Yet little is known about the fungal community in lake sediment. In this study, sediment samples from five habitat types in Baiyangdian Lake (BYD Lake) were collected across three seasons. High-throughput sequencing techniques were used to determine the compositions of fungal communities. Fungi are highly diverse in the sediment of BYD Lake, although some important fungi have not been accurately identified. The fungal diversity was highest in winter and lowest in summer, while the variations of species richness among sampling sites were not significant. The compositions of fungal community differed among seasons and habitats. Physicochemical properties of sediments were measured and the influence of the environmental factors on fungal communities were analyzed. Temperature, P, N, and heavy metals explained 48.98% of the variations of fungal communities across three seasons. Human activities have affected the species and biomass of fungi to some extent. Temperature is the most influential factor and is negative to fungal diversity. Nutrient element in different forms have different effects on shaping the fungal community. The effect of heavy metals is not clear.

Current paper is aiming to show the obtained results in manufacturing and characterization of graphite-based and metal composite materials suitable to be used in high voltage applications of automotive and/or aviation field. Thus, 4 types of materials have been processed and tested in order to assess their suitability to be used as current collector material for electric engines. The novelty of this work is the presentation of the new innovative technological process for obtaining the carbon/metal composite material used in the manufacture of sliding contacts for current collector heads, as well as the characteristics obtained for this material. All 4 obtained materials have been characterized from structural, mechanical and functional point of view and the most suitable of them has been chosen to be further developed by the end beneficiary.

High-frequency circuit performance is significantly impacted by impedance variations, particularly within the low-resistance regime. Traditional Ohm’s Law based modeling approaches often fail to accurately predict circuit behavior in these conditions, leading to design inaccuracies and potential system failures. The Standard Ohm’s Law based model’s prediction of infinite current as resistance approaches zero is physically unrealistic and hinders its application in practical scenarios. Despite the recognition of these limitations, existing models have not comprehensively addressed the complex impedance behavior observed in high-frequency circuits. To overcome these challenges, this paper introduces a modified version of the Ohm’s Law incorporating an exponential correction term. The Modified Ohm’s Law’s accuracy was evaluated through simulated experiments across a wide frequency range (1kHz to 1GHz) using various electronic components. The findings demonstrate the superior performance of the modified model in predicting currents under low-resistance and high-current conditions compared to the Standard Ohm’s Law model. By providing finite and accurate current values, the proposed model effectively mitigates the unrealistic infinite current predictions of the standard approach. The enhanced predictive capabilities of the Modified Ohm’s Law hold significant implications for high-frequency circuit design and analysis. Its application can lead to improved performance and reliability in power electronics, telecommunications, and other high-frequency systems. By incorporating non-linear impedance behavior, the model offers a more accurate representation of real-world circuit conditions. Future research should focus on refining the exponential term’s parameters to optimize the model's accuracy across a broader range of applications. Additionally, real-time implementation and hardware validation are essential to assess the model's practical utility in complex circuit environments.

In veterinary medicine, the significance of High-Density Lipoprotein (HDL) measurements is not well-documented than it is in humans. The HDL level can be measured in dogs, and through referring to the normal range, it is possible to find out what this means for various endocrine diseases and hyperlipidemia diseases. Aim of this study is to measure the HDL levels in dogs with various conditions and to evaluate whether the Total Cholesterol (TC), HDL ratio is effective as a prognostic indicator in various hyperlipidemia and endocrine diseases. Through prospective clinical trial, sixteen client-owned dogs and cats visiting a local private practice were divided into three groups; five dogs without hyperlipidemia or metabolic disease (Group 1); eight animals with Cushing's, hypothyroidism, and gallbladder sludge (Group 2) and three diabetics, urinary disorders, and healthy cats (Group 3). In two dogs, the TC/HDL values were between 2 and 3; in two dogs, the values were between 3 and 4; in two dogs, the values were between 4 and 5. In three dogs, the TC/HDL values were between 5 and 6 and in three dogs, the ratio values were between 6 and 7. The other value was higher than 8. Except two dogs which showed lower value than 3, all dogs had concurrent endocrine disease including Cushing’s disease, hypothyroidism, gall bladder mucocele, hyperlipidemia. There was a difference in each group in terms of the TC/HDL value compared to the group with underlying disease. This means that TC/HDL values can be an excellent indicator of endocrine disease in dogs as well. In cats, although this is a very small sample, a high TC/HDL value of 9 points are shown in the cat which had diabetes mellitus. However, for more statistically significant results, a larger sample group for further investigation is needed.

This study presents a detailed comparative analysis of Molecular Docking data, focusing on the binding interactions of conventional ligands and natural compounds, Apigenin and Luteolin, with TP-53, pRb, and APOBEC. Utilizing advanced bioinformatics techniques, coupled with Ar-tificial Intelligence software and High-Performance Computing (HPC), we measured and con-trasted the binding energies of these interactions. Additionally, we investigated protein-protein interactions between HPV-16 oncoprotein E6 and tumor suppressors TP-53 and pRb. Our findings demonstrate that the natural compounds Apigenin and Luteolin exhibit significantly higher binding affinities to TP-53, pRb, and APOBEC compared to conventional pharmacological ligands. The binding energies for Apigenin and Luteolin were approximately -6.9 kcal/mol and -6.6 kcal/mol, respectively, indicating their strong potential as therapeutic agents in inhibiting the oncogenic functions of HPV-16. In contrast, conventional ligands showed lower binding affinities, with energies around -4.5 to -5.5 kcal/mol. The study further revealed that the protein-protein interactions between E6 and TP-53, and E6 and pRb, exhibited considerably higher binding en-ergies, approximately -976.7 kcal/mol, due to the multiple interaction sites and the complex nature of protein interfaces. A conversion formula was developed to translate these high-energy inter-actions to a comparable scale for non-protein-protein interactions, highlighting the superior binding potential of natural compounds, which, through the same conversion formula, was shown to be higher than that of interaction between E6 with TP-53 and E6 with pRb. These results underscore the therapeutic promise of Apigenin and Luteolin in preventing HPV-16-related on-cogenesis. By demonstrating their higher binding affinities to crucial tumor suppressors, this study supports the development of natural compound-based therapies. The findings also em-phasize the necessity for further experimental validation to explore these compounds' efficacy in clinical settings. This comprehensive analysis provides a robust framework for understanding the comparative binding interactions and lays the groundwork for innovative therapeutic strategies against HPV-16.

The development of solar energy on a regional scale necessitates a thorough understanding of available resources. Cuba, facing prolonged economic, environmental, and energy crises, urgently needs to enhance its sustainability through solar energy. While solar resource mapping is widespread, Cuba lacks extensive field measurements, often relying on models that may not be ideally suited for large regions like Matanzas province. Spanning over 12,000 km² with nearly 150 km between its northern and southern extremes, Matanzas presents challenges for high-resolution solar mapping. This study introduces a methodology that integrates various methods and databases to achieve maximum resolution in the resulting solar map. The approach is designed for large areas where conventional high-resolution models fall short. By optimizing calculation times and parameterizing the entire surface latitudinally, a high-resolution solar resource map for Matanzas has been developed. This map significantly enhances the understanding of solar resources in Cuba and proposes new methodologies for analyzing solar potential in similarly large regions.

It is imperative to conduct experimental studies on the seepage behavior of gas-bearing coal under cyclic dynamic loading conditions. This paper focuses on the evolution of coal permeability under the combined effects of dynamic loading, static loading, and gas adsorption. The principal conclusions are as follows. (1) As the frequency and amplitude of dynamic loading increase, the development of pore and fissure structures within the coal body becomes increasingly pronounced during dynamic loading cycles, resulting in a gradual rise in permeability. Notably, as the coal approaches its yielding stage, the permeability can increase by up to 47%. (2) The permeability curve is divided into four regions: the compaction reduction zone, the oscillation zone, the gradual recovery zone, and the abrupt increase zone of failure. Ultimately, in the failure phase, the permeability surges dramatically, potentially reaching 4 to 5 times the initial permeability. (3) When the static load stage is constant, the rate of change in permeability of the coal under dynamic loading decreases with increasing adsorption amount. When the adsorption amount is constant, the rate of change in permeability of the coal under dynamic loading increases with the increase in static load stress stage, with the maximum increase reaching 75.2%. It can be concluded from the rate of change in permeability and the dynamic loading sensitivity coefficient that the permeability of the coal is highly sensitive to cyclic dynamic loading, with increased sensitivity associated with larger static load stages and decreased sensitivity with greater adsorption amounts.

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale, at high temperatures. We used a picosecond laser to precisely cut micro-beams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm, and a length of ~1 cm. They were then tested in a thermal-mechanical analyzer at room temperature, 500°C, 800°C, and 1100°C using the four-point flexural testing method. We compared the elastic moduli of high-purity Al2O3 and AlN measured by our method with the reported values in the literature and found that the difference was less than 5% for both materials. This paper provides a new and accurate method of characterizing the high-temperature elastic modulus of miniature samples extracted from representative/selected areas of bulk materials.

The comprehensive analysis of cross-country skiing races is a pivotal step in establishing effective training objectives and tactical strategies. This study aimed to establish a method for the classifi-cation of sub-techniques and analyzing skiing characteristics during cross-country skiing skating style timed races on snow using high-precision kinematic GNSS devices. The study involved at-taching GNSS devices to the heads of two athletes during skating style timed races on cross-country ski courses. These devices provided precise positional data and recorded vertical and hor-izontal head movements and ground over velocity (VOG). Sub-techniques were classified by de-fining waveform patterns for G2, G3, G4, and G6 based on these data. The validity of classifica-tion was verified by comparing GNSS data with video analysis, a process that yielded classifica-tion accuracies ranging from 94.0% to 99.3% for G2, G3, G4, and G6. Notably, G4 emerged as the fastest technique, with sub-technique selection varying among skiers and being influenced by skiing velocity and course inclination. The study's findings have practical implications for ath-letes and coaches, as they demonstrate that high-precision kinematic GNSS devices can accurate-ly classify sub-techniques and detect skiing characteristics during skate-style cross-country skiing races, thereby providing valuable insights for training and strategy development.

With the development of Global Navigation Satellite Systems (GNSS), the quality and anti-jamming capability of satellite navigation signals are crucial. Binary Offset Carrier (BOC) modulation faces issues of false locking due to multi-peak ambiguity in its autocorrelation function, limiting its application. This paper examines FH-BOC modulation, which integrates BOC with frequency hopping technology, significantly improving anti-jamming, anti-multipath performance, and spectral efficiency. To meet the high dynamic tracking demands of FH-BOC signals, this study explores three types of carrier tracking loops: the traditional second-order frequency-locked loop assisted a third-order phase-locked loop, a linear Kalman filter-based tracking algorithm, and an adaptive Kalman filter-based tracking algorithm. A composite code tracking loop is also proposed. Simulations show that the adaptive Kalman filter algorithm achieves high-precision carrier tracking in dynamic environments and quickly converges during transitions. The composite code tracking loop, aided by the carrier loop, ensures precise synchronization of pseudocode and frequency-hopping subcarrier phases, demonstrating the superior performance of FH-BOC modulation in dynamic environments.

Land subsidence is an environmental hazard occurring gradually over time, potentially posing significant threats to the structural stability of civilian buildings and essential infrastructures. This study presented a workflow using the SBAS-PSInSAR approach to analyze surface deformation in the Choushui River fluvial plain (CRFP) based on Sentinel-1 SAR images and validated against precise leveling. Integrating InSAR results with hydrogeological data, such as groundwater levels, multilayer compactions, and borehole loggings, a straightforward model was proposed to estimate appropriate groundwater level drops to minimize further subsidence. The results showed a huge subsidence bowl centered in Yunlin, with maximal sinking at an average 60 mm/year rate. High-resolution subsidence maps enable the quantitative analyses of the safety issues for Taiwan High Speed Rail (THSR) across the considerable subsidence areas. In addition, the analysis of hydrogeological data revealed that half of the major compaction in the study area occurred at shallow depths. Based on a maximal subsidence control rate of 40 mm/year specified in the CRFP, the model results indicated that the groundwater level drops from wet to dry seasons needed to be maintained from 3-5 m for the shallowest aquifer and 4 – 6 m for aquifers 3 and 4. The workflow demonstrated the compatibility of InSAR with traditional geodetic methods and the effectiveness of integrating multiple data sources to assess the complex nature of land subsidence in the CRFP.

To explore the coupling mechanism between urban-rural transformation (URT) and the ecological environment in counties forms the basis for achieving high-quality and sustainable county development. Despite the richness of research on the relationship between urban and rural development and the ecological environment, the county level remains the basic unit of rural revitalization in China, and further research on the coupling mechanism between URT and the ecological environment at this level is needed. Therefore, the study developed an evaluation system for URT, incorporated NDVI data indicators, and employed the coupling coordination degree (CCD) model along with GIS tools to investigate the spatio-temporal pattern of URT and NDVI evolution, and the CCD in each administrative village within Lingbao City. Additionally, a geoDetector model was employed to analyze the influencing factors affecting the CCD of URT and NDVI. Finally, the study explores the coupling mechanism and optimization path. The result shows that: (1) During the study period, the URT level in administrative villages within the study area markedly improved, while NDVI exhibited an increasing-then-decreasing trend; (2) The CCD between URT and NDVI in the northern and central regions of the study area is higher than that in the southern region, with an overall low level; (3) The spatial heterogeneity of CCD is significant, largely influenced by socio-economy, natural environment, policy funds, and geographical location, where the elements comprising CCD mutually influence each other; (4) Drawing upon the coupling and coordination dynamics between URT and the ecological environment within Lingbao City, this research categorizes it into seven types with distinct optimization paths. This study provides a valuable reference for guiding the high-quality and sustainable development strategies for mountainous and hilly counties within the Yellow River basin.

Through the geometric relationships and force analysis of the main components of the panto-graph on high-speed trains, coefficients of aerodynamic forces and lift transmission between the pantograph and main components under crosswind conditions were derived. Based on the aer-odynamic forces acting on the pantograph at different crosswind speeds, wind angles, and oper-ating speeds, the aerodynamic lift of the pantograph and main components was ultimately de-termined. The results indicate that the aerodynamic lift of the pantograph is mainly distributed on the bow structure, with the aerodynamic lift of the upper frame all being negative values, while the absolute value of the aerodynamic lift of the lower arm rod is the smallest. The oper-ating speed of the pantograph and the wind angle of the crosswind have a significant impact on the aerodynamic lift of the main components, while the impact of the crosswind speed is rela-tively small. At the same operating speed of the pantograph, the lower the corresponding crosswind speed, the smaller the aerodynamic lift of the pantograph. The aerodynamic lift of the pantograph tends to decrease gradually with the increase of crosswind speed, and the impact of crosswind speed decreases gradually with the increase of pantograph operating speed. A com-prehensive relationship formula between the aerodynamic lift of the pantograph and the oper-ating speed, crosswind speed, and wind angle is obtained, and the empirical formula for the contact force of the bow net and train operating speed is modified. The research results are of great significance and value for the study and application of lift forces on pantographs under crosswind conditions.

Within the phenomenology of particle physics, the theoretical model of 4-zero textures is validated using a chi-square criterion that compares experimental data with the computational results of the model. Traditionally, analytical methods that often imply simplifications, combined with computational analysis, have been used to validate texture models. In this paper, we propose a new meta-heuristic variant of the differential evolution algorithm that incorporates aspects of the particle swarm optimization algorithm called "HE-DEPSO" to obtain chi-squared values are less than a bound value, which exhaustive and traditional algorithms cannot obtain. The results show that the proposed algorithm can optimize the chi-square function according to the required criteria. We compare simulated data with experimental data in the allowed search region, thereby validating the 4-zero texture model.

Metal-reinforced polymethyl-methacrylate (PMMA) is considered the gold standard material for immediate loading on dental implants. However, mechanical problems under loading cycles can occur, such as fractures. To overcome these drawbacks, a novel polymer-based material has been proposed. The aim of the present in vitro comparative research is to validate a novel composite polymer developed to replace metal-reinforced PMMA interim restoration due to its advantages of good mechanical proprieties, easier manufacturing, and handling. Ten interim restorations were CAD/CAM designed and fabricated (five in the composite "ONLY" group, and five in the metal-reinforced PMMA group). All the samples were screwed into the prototype models, simulating a complete edentulous mandible rehabilitated with six straight implants. Outcome measures were breakpoint (load, N) and displacement (mm) thought a static, compression test and material behavior under dynamic cyclic test method (fatigue test). A total of twenty samples were tested. Ten samples were used for each test (10 for static and 10 for dynamic), five samples were used in each group (test and control). All the specimens completed the mechanical tests, as planned. There was no statistically significant difference between groups for all, breakpoint, displacement and fatigue tests. Breakpoint in the test group was 1953.19 ± 543.73 N, while, it was 2031.10 ± 716.68 N in the control group, with no statistically significant difference (P=0.775). The displacement was 1.89 ± 0.34 mm in the test group and 1.98 ± 0.75 mm in the control group, again, with no statistically significant difference (P=0.763). Under dynamic cyclic test method, in the control group the mean load was 2504.6 ± 972.15 N, while, in the test group the mean load was 3382 ± 578.5 N. The difference between group was 877.4 ± 579.3 N (p value=0.121). With the limitation of this in vitro study, the novel composite polymer can be used to immediately load dental implants. Further clinical researches are needed to confirm this preliminary results.

At 8000 m and above, a ‘death zone’ reputation afforded protection for the fragile ecosystems of the Himalaya and Korakoram ranges for thousands of years. After decades of high-altitude mountaineering, environmental impacts have been documented such as associated carbon-intensive air travel and contamination from waste. Despite the growing popularity, high-risk and fragile context of the sport, the behaviour, perspectives and experiences of high-altitude mountaineers, and the social and economic consequences have not been researched. Following an interpretive paradigm and using purposive sampling, this qualitative study conducted in-depth interviews and open-ended survey questions to collect the experiences of sixteen high-altitude mountaineers. Analysis of the qualitative data was informed by Grounded Theory with the coding process leading to the overarching category of ‘leave no trace’. The results show how the high risks to life, and growing popularity of the activity influence mountaineer’s ability to act sustainably and increase unsustainable behaviour despite a desire to ‘leave no trace’ on the mountain. Meanwhile, climate change has already and will increasingly have profound impacts on the risks associated with 8000m mountaineering. Allowing more time for acclimation would help to address the root causes of unsustainable behaviours along with better enforcement of regulations.

In order to apply RAP fine aggregate to High Modulus Asphalt Concrete(HMAC), this study first extracts aged asphalt from RAP fine aggregate through extraction and distillation, and adds it to high modulus modified asphalt in proportions of 20%, 40%, 60%, and 80%. The performance changes of the recycled asphalt were investigated using conventional performance tests and dynamic shear rheological tests (DSR). Microscopic techniques such as four‐component analysis and infrared spectroscopy were employed to explain macroscopic performance changes in terms of component and functional group changes in the asphalt. Using HMAC‐20 gradation as an example, uniaxial compression dynamic modulus tests, rutting tests, freeze‐thaw splitting tests, and low‐temperature bending tests were conducted to evaluate the performance changes of recycled asphalt mixture with different RAP fine aggregate contents through four indices: dynamic modulus, dynamic stability, tensile strength ratio (TSR), and maximum bending strain. The results indicate that for every 20% increase in aged asphalt, the penetration at 25°C, ductility at 25°C, and dynamic viscosity at 60°C decrease by approximately 6.2%, 15.4%, and 3.9%, respectively, while the softening point increases by approximately 13.3%. It is concluded that the addition of aged asphalt significantly affects the ductility at 25°C and the softening point. As the aged content increases, the complex shear modulus (G*) and phase angle (δ) of the recycled asphalt decrease, while the rutting factor increases. The four‐component analysis and infrared spectroscopy of the asphalt demonstrate that the incorporation of aged asphalt is merely a physical blending phenomenon, involving changes in the content of the four components without the formation of new functional groups (new peaks). When RAP fine aggregate is applied to high modulus recycled asphalt mixture, compared to high modulus modified asphalt mixture, the recycled mixtures exhibit higher dynamic modulus and dynamic stability, but significantly reduced water stability and low‐temperature performance.

In recent years, the High Dynamic Range (HDR) image has gained widespread popularity 1 across various domains such as security, multimedia, and biomedical fields, owing to its ability 2 to deliver an authentic visual experience. However, the extensive dynamic range and rich detail 3 in HDR images present challenges in assessing their quality. Therefore, current efforts involve 4 constructing subjective databases and proposing objective quality assessment metrics to achieve 5 efficient HDR Image Quality Assessment (IQA). Recognizing the absence of a systematic overview 6 of these approaches, this paper provides a comprehensive survey of existing HDR IQA methods. 7 Furthermore, this paper aims to serve as a valuable resource for researchers by discussing the 8 limitations of current methodologies and potential research directions in the future.

Measuring cell confluence in high-throughput screening of pharmaceutics, cell culture monitoring, cancer research, and industrial applications requires quantitative and standardizable measures to minimize subjective observations and increase throughput1-12 . Over the past half-century, non-invasive specialized programs have been created to quantitatively assess cell confluence, and some software tools exist to meet these needs1,4,5,6,7,8,9 . However, many of these tools are expensive, computationally-demanding, or inaccessible to non-experts1,6. With the assistance of generative artificial intelligence, we have developed the Confluence Analysis Program (CAP), a modern tool designed to be precise, interactive, and user-friendly. CAP is written entirely in Python and runs in any command-line interface (CLI), including Terminal (OS) and Command Prompt (Windows). In addition to fetching all necessary external libraries automatically and prompting drag-and-drop image retrieval, CAP features live visual comparison of cell mass identification to the original image assay. Our results demonstrate robust performance of CAP on fluorescent micrographs of varying confluences ranging from low to high. CAP is provided as a free resource, accessible in the Supplementary Materials.

As waterflooding multi-layer reservoirs get into the high-water-cut stage, inter-layer conflicts become increasingly serious, leading to a worsening development effect over time. Production layers regroup is an effective approach for resolving inter-layer conflicts and improving waterflooding efficiency. At the current stage, there are limitations for most of the methods of production layers regroup. This article proposes a smart method for optimizing the layer regroup plan based on genetic algorithm. Comprehensively considering various factors that affect the regroup of layers, based on the combination principle of "smaller intra-group variance and larger inter-group variance of each influencing factor are expected ", genetic algorithm is used to calculate the fitness value of the initial combination schemes, the advantageous schemes with higher fitness values are selected as the basis of the next generation. Then crossover and mutation operations are performed to those advantageous schemes to generate new schemes. Through continuous selection and evolution, until the global optimal solution with the highest fitness value is found, the optimal combination scheme is determined. Comparative analysis with numerical simulation results demonstrates the reliability of this intelligent method, with an increased oil recovery of 4.34% for the sample reservoir. Unlike selecting a preferable plan from a limited number of predefined combination schemes, this method is an automatic optimization to solve the optimal solution of the problem. It improves both efficiency and accuracy as compared to conventional reservoir engineering methods, numerical simulation methods and most of the mathematical methods, thus could provide effective guidance for EOR strategies of waterflooding reservoirs in high-water-cut stage.

Objectives: To rate the effects of low molecular weight hyaluronic acid (LMWHA) solution and high concentration oxygen (HCO) through a specific medical device (Caress Flow©), compared to topical administration of hyaluronic acid (HA) alone on symptoms of mild and moderate stress and mixed urinary incontinence in women with genitourinary syndrome of menopause (GSM). Methods: A total of 68 postmenopausal women were enrolled (from October 2021 to September 2023). Patients were separated in two groups: one group used therapy with LMWHA solution and HCO combined and the second group used therapy with HA alone. Patient Global Impres-sion of Improvement (PGI-I) as the first outcome was used. As secondary outcomes International Consultation on Incontinence Questionnaire - short form (ICIQ-SF) questionnaire and Internation-al Quality of Life (IQoL) questionnaire were used. Results: Sixty-eight (68) women, 35 (51%) and 33 (49%), were treated with LMWHA solution and HCO combined and HA alone for 10 weeks, respectively. 28 (80%) versus 7 (20%) women reported an improvement (PGI-I score ≤3) of the symptoms in LMWHA solution and HCO com-bined group versus HA alone group. According to the ICIQ-SF, a statistically significant differ-ence was recorded after treatment between the two groups (median, 7 [5-11] vs 10 [8-11]; P = 0.03). According to the IQoL questionnaire, a statistically significantly lower median score was recorded in the LMWHA solution and HCO combined compared with the HA group, before (71 [IQR 55-81] vs 89 [IQR 67-94]; P < 0.01) and after (78 [IQR 65-86] vs 88 [IQR 72-99]; P = 0.04) treatment. Conclusions: LMWHA solution and HCO combined might improve the mild and moderate stress and mixed urinary incontinence in this set of women and that it is superior to HA therapy alone. However, these results need to be confirmed in further studies with a controlled design and a larger population.

We investigated the effect of 0.6 MeV proton irradiation on the superconducting and normal state properties of thin-film YBa2Cu3O7−δ superconductors. A thin-film YBCO superconductor (≈ 567 nm thick) was subject to a series of proton irradiations with a total fluence of 7.6×1016p/cm2. Upon irradiation, Tc was drastically decreased from 89.3 K towards zero with a corresponding increase in its normal state resistivity above Tc. This increase in resistivity which indicates the increase of defects inside the thin-film sample can be converted to the dimensionless scattering rate. We found that the relation between Tc and dimensionless scattering rate obtained during proton irradiation approximates the generalized d-wave Abrikosov-Gor’kov theory better than the previous results obtained from electron irradiations. This is an unexpected result since the electron irradiation is known to be most effective to suppress superconductivity over other heavier ion irradiations such as proton irradiation. It suggests that the type of defects created by proton irradiation evolves from cascade defects (in bulk single crystals) to point-like defects (in thin-film single crystals) as the thickness decreases.

As high strength and ultra-high strength steels are widely used in all kinds of modern welded constructions, a lot of research is carried out to investigate the mechanical properties of weldments of these steels but there is a scarce information on such important characteristic as their corrosion behaviour. This research focuses on the corrosion behaviour of weld metal of weldments of S906QL and S700MC steels. Weld metal was tested electrochemically in a 3,5% NaCl aqueous solution via potentiodynamic scan to determine corrosion rate and its dependence on welding gap. No influence of welding gap on corrosion rate was found but the experimental results suggested that corrosion rate depended on the chemical composition of filler material and the microstructure of weld metal.

The nonlinear dynamics exhibited by aircraft flying at high angle of attack (AOA) pose great challenges to the design of flight control. The control design based on nonlinear dynamic inversion (NDI) is to reversely find the required control input based on the current nonlinear dynamics of the aircraft and the control objectives to be achieved. Since it is derived from the nonlinear dynamics of the aircraft, a single NDI controller can cover the entire flight envelope without the need for controller switching or gain scheduling. This paper employs the layered structure of the flight control loop to implement the NDI controller through the combination of aerodynamic control and thrust vectoring control (TVC). The resulting NDI controller is applied to an experimental F-16 installed with TVC to verify its high AOA maneuverability in the post-stall region. The verification simulation shows that the experimental F-16 under the NDI control can effectively track the high AOA command and successfully demonstrate the Herbst maneuver by performing the heading reversal with 70° AOA.

Neuroblastoma (NB) is a solid tumor occurring in infancy and childhood, whose high-risk form has currently a survival rate &lt; 50 %, despite aggressive treatments. Additionally, drugs-induced secondary tumorigenesis and the emergency of drug resistance worsen the already worrying scenario, calling for an urgent development of new extra-genomic treatments. Quaternary phosphonium salts (QPSs) possess both antimicrobial and anticancer effects. Triphenyl phosphonium salts (TPPs) are mitochondria-targeting compounds, exerting anticancer effects, impairing mitochondria functions and damaging DNA, at the same time. TPP-based bola-amphiphiles, previously proven to self-assemble nanoparticles (NPs) in water and successfully assayed as possible antibacterials, were never tested as suitable antitumor agents. Here, aiming at the development of new antitumor devices to counteract resistant forms of NB, the anticancer effects of a TPP-based amphiphile molecule have been investigated for the first time. To this end, we considered the water-soluble sterically hindered quaternary phosphonium salt (BPPB) encompassing two triphenyl phosphonium groups linked by a C12 alkyl chain, thus embodying both the characteristics of mitochondria-targeting compounds and those of bola-amphiphiles. The anticancer effects of BPPB were assessed against HTLA-230 human stage-IV NB cells and their counterpart resistant to etoposide (ETO), doxorubicin (DOX) and to many other therapeutics (HTLA-ER). Determined IC50 values were very low on both cell populations, already after 24 hours of treatment, when cells viability did not significantly differ from that observed for the longest exposure timing. Moreover, to investigate a putative future inclusion of BPPB in a chemotherapeutic cocktail for NB, its cytotoxic effects were assessed against mammalian cell lines. These included monkey kidney cells (Cos-7), human hepatic cells (HepG2), a lung-derived fibroblast cell line (MRC-5) and red blood cells. From appreciable to very high selectivity indices have been determined after 24 hours treatments, an exposure time after which both NB cell populations tested appeared already fully exterminated.

The rapid expansion of flexible and wearable electronics has necessitated a focus on ensuring their safety and operational reliability. Gel Polymer Electrolytes (GPEs) have become preferred alternatives to traditional liquid electrolytes, offering enhanced safety features and adaptability to the design requirements of flexible lithium-ion batteries. This review provides a comprehensive and critical overview of recent advancements in GPEs technology, highlighting significant improvements in their physicochemical properties, which contribute to superior long-term cycling stability and high-rate capacity compared to traditional organic liquid electrolytes. Special attention is given to the development of smart GPEs endowed with advanced functionalities such as self-protection, thermotolerance, and self-healing properties, which further enhance battery safety and reliability. The review also critically examines the application of GPEs in high-energy cathode materials, including Lithium Nickel Cobalt Manganese (NCM), Lithium Nickel Cobalt Aluminum (NCA), and thermally stable Lithium Iron Phosphate (LiFePO4). Despite the advancements, several challenges in GPE development remain unresolved, such as improving ionic conductivity at low temperatures and ensuring mechanical integrity and interfacial compatibility. The review concludes by outlining future research directions and the remaining technical hurdles, providing valuable insights to guide ongoing and future efforts in the field of GPEs for lithium-ion batteries, with a particular emphasis on applications in high-energy and thermally stable cathodes.

This study investigates the microstructural evolution and mechanical properties of high-nickel shipbuilding steel during thermal processing using High Temperature Confocal Laser Scanning Microscopy (HTCLSM). The in-situ observation of the heating and holding processes reveals critical insights into phase transformations, grain growth behavior, and the formation of precipitates. The experimental results demonstrate that austenitization begins at approximately 700°C, with significant grain boundary nucleation. At 900°C, the formation of black precipitates was observed, and their persistence up to temperatures exceeding 1000°C was confirmed. Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) analyses identified these precipitates as chromium carbides (Cr7C3), which significantly contribute to the material's strength. The comprehensive analysis using Transmission Electron Microscopy (TEM) confirmed the presence and distribution of Cr7C3 within the grains and along grain boundaries. These findings provide a deeper understanding of the microstructural dynamics in high-nickel steels, guiding the optimization of heat treatment processes to enhance mechanical properties for maritime applications.

This article presents the theoretical study, numerical simulation and the fabrication of a phase shifter and stub resonator in microstrip ridge gap waveguide (MGCW) technology with the use of liquid crystal (LC) in its substrate as a reconfigurable material. The phase shifter and the stub resonator are filled with LC and thanks to LC's dielectric anisotropy properties, the phase shift and resonance response can be easily controlled using an external electric or magnetic bias field. The phase shifter was designed to operate in the range of 10 to 20 GHz and the resonator was designed to operate in the range of 7.8 to 8.8 GHz. The phase shifter's insertion losses, associated with both parallel and perpendicular LC's permittivity, as well as the phase response were computed and measured. Finally, the figure of merit (FoM) was extracted. The resonator's frequency response, associated with both parallel and perpendicular LC's permittivity, was computed. The resonator's frequency responses, provided different polarization voltages, were measured and compared to the simulation results. The technological issues were discussed. The good agreement between simulation and measurement results establishes this technology as a viable approach to the development of RF reconfigurable devices.

Additive manufacturing (AM) or 3D printing is a promising industrial technology that enables rapid prototyping of complex configurations. Powder Bed Fusion (PBF) is one of the most popular AM techniques for metallic materials. Until today, only a few metals and alloys are available for AM, e.g. titanium alloys, the most common of which is Ti-6Al-4V. After optimization of the PBF parameters, with or without post processing such as heat treatment or hot isostatic pressing, the printed titanium alloy can easily reach tensile strengths of over 1100 MPa due to the quickly cooling of AM process. However, attributed to the unique features of metallurgical defects and microstructure introduced by this AM process, their fatigue strength has been low, often only not less than 30% of the tensile strength, especially in very-high-cycle regime, i.e. failure life beyond 107 cycles. Here, we have reviewed the current state of research on the very-high-cycle fatigue (VHCF) of additively manufactured (AMed) titanium alloys, refined the basic quantities of AMed microstructure and metallurgical defects, summarized the main factors limiting their VHCF strengths, and suggested possible ways to improve VHCF performance.

Void fillers are required for osseous gaps generated after orthopedic procedures as medial open-wedge high-tibial osteotomy (MOWHTO) to provide sufficient structural support and a rapid osteosynthesis. We developed a novel three-dimensional (3D) printing-based platform technology using the customized 3D scaffolds covered with polycaprolactone (PCL)/β-tri-calcium phosphates (β-TCP)/bone decellularized extracellular matrix (dECM) for use as bone substitute scaffold, which can be effectively exploited to estimate the calculated correction angle with preoperative simulations. PCL/β-TCP/bone dECM scaffolds demonstrated significantly higher cell contain levels in cell seeding efficiency, excellent proliferation capacity, and promotion of early osteogenic differentiation compared with PCL/β-TCP scaffolds. The scaffolds promoted bone mineralization at the early time points of an in vivo study (8 weeks) and exhibited biodegradable properties (38% for 16 weeks). The correction angle measured after osteotomy using 3D printed scaffolds was estimated with high accuracy with low errors (10.3° ± 0.9°), was and was not significantly different even in the presence of lateral cortical hinge fractures. The customized 3D scaffold enriched with PCL/β-TCP/bone dECM yielded excellent cell seeding efficiency, proliferation capacity, early osteogenic differentiation, and bone mineralization outcomes. It is expected to solve the disadvantages related with bone union in MOWHTO, and to replace autografts in the future.

The durability of bridge decks is a critical factor in ensuring the safety and longevity of transportation infrastructure. This article explores advanced materials and innovative techniques designed to mitigate cracking in bridge decks, a common issue that can compromise structural integrity and increase maintenance costs. It provides a comprehensive review of cutting-edge solutions such as Fiber-Reinforced Polymers (FRP), High-Performance Concrete (HPC), Ultra-High Performance Concrete (UHPC), and self-healing concrete technologies. Each material is analyzed for its ability to enhance strength, reduce permeability, and improve resistance to environmental stressors. Additionally, the article examines the role of surface treatments, sealants, and routine maintenance practices in prolonging the life of bridge decks. By synthesizing current research and practical applications, this article offers valuable insights and recommendations for engineers, contractors, and policymakers seeking to advance bridge deck durability through innovative materials and methodologies.

The present study examined metabolites in Northern wild rice (WLD), the impact of WLD supplemented high fat (HF) diet on gut microbiota, short chain fatty acids (SCFAs) and correlation with metabolism or inflammation versus HF+white rice (WHR) in mice. C57BL/6J mice received HF diet supplemented with 26g% WHR, 26g% WLD, or 13g% WHR+13g% WLD (WTWD) for 12 weeks. The levels of fasting plasma glucose, total cholesterol, triglycerides, insulin resistance, inflammatory cytokines and monocyte adhesion were lower, and the abundances of fecal Lactobacillus gasseri species bacteria and propionic acid were higher in HF+WLD diet-fed mice compared to HF+WHR diet-fed mice (p<0.05). The anti-inflammatory effects of HF+WTWD diet were weaker than that in HF+WLD diet, but were greater than that in HF+WHR diet-fed mice (p<0.05). Relative abundances of fecal Lactobacillus gasseri and propionic acid in HF+WLD fed-mice were higher than that in HF+WHR fed mice. The abundance of fecal L. gasseri and propionic acid negatively correlated with metabolic and inflammatory markers (p<0.05). The findings suggest that WLD dose-dependently attenuated metabolic and inflammatory disorders in HF diet-fed mice. Interactions between WLD components and gut microbiota may upregulate fecal propionic acid and contribute to metabolic and anti-inflammatory benefits of WLD diet-induced insulin resistant mice.

Background: This study investigated the effect of indirect air-cooling on the variation in intrapulpal temperature (ΔT) during different light-curing protocols of bulk-fill resin composites in molars with class V cavities. Methods: A nonretentive class V cavity was prepared in an upper molar. The intrapulpal temperature changes with and without air-cooling were recorded with type K thermocouple. The cavity was restored with bulk-fill resin composites: Tetric PowerFlow and Filtek Bulk-Fill Flow. The tooth was exposed to different light-curing protocols (n=5) using the Valo Grand light-curing unit: (i) high-intensity light-curing of 3200 mW/cm² (3 and 6 s) and (ii) moderate-intensity light-curing of 1000 mW/cm² (10 and 20 s). The ΔT data were subjected to two-way ANOVA, followed by Bonferroni post hoc test. Results: A significant increase in temperature was observed with the use of the high-intensity light-curing resin composite without indirect air-cooling. In addition, the application of air-cooling significantly decreased the temperature in all the groups except for the Tetric PowerFlow bulk-fill resin composite at 3 s of light-curing. Conclusion: Indirect air-cooling resulted in a lower increase in intrapulpal temperature during the light-curing of bulk-fill resin composites, making it an effective alternative for controlling the temperature rise in class V restorations with 1 mm of remaining dentin.

This study investigates the fatigue behavior of cold-finished mild steel subjected to electrochemical hydrogen charging under controlled conditions. Samples were hydrogenated at constant time in a fixed electrolyte pH after which they underwent fatigue testing under constant loading condition with fixed frequency. The primary objective was to assess the impact of varying hydrogen permeation levels on the number of cycles to failure. The experimental results revealed a complex relationship between hydrogen concentration and fatigue life. Initially, as hydrogen permeation increased, the number of cycles to failure substantially decreased, demonstrating a detrimental effect of diffused hydrogen on fatigue resistance of samples. This decline in fatigue life was attributed to hydrogen embrittlement (HE) and hydrogen-enhanced decohesion (HEDE) phenomena, which collectively facilitate crack initiation and propagation. However, at high hydrogen concentrations, an unexpected increase in number of cycles to failure was observed suggesting the existence of a threshold hydrogen concentration beyond which the fatigue mechanisms may be altered, potentially due to saturation of hydrogen-related defects and mechanisms such as Hydrogen Enhance Localized Plasticity (HELP). The insights gained from this research have significant implications for the material's application in hydrogen-rich environments, such as those encountered in the energy and transportation industries.

This study investigated the aerodynamic performances of various trains with different nose shapes, using as design variables two angles α,β for the heads shape and the bluntness angle γ, without crosswind. The effect on aerodynamic performances, such as the train drag coefficient, pressure distribution along the train surface, flow structures around the train and the wake, head pressure pulse, were analyzed. The results indicate that the increase of the train nose length for flat shapes decreases the CD values by 21.47% and 19.11%, decreasing the high-pressure region in the leading head. The duck-nose configuration emerges as a compromise between drag reduction and nose length. Increasing the angle γ a further drag reduction of 8.5% is featured. Drag formation along the train is also analyzed. The steeper the variation of the geometry, the higher the peak intensity and the slope of the curve. Regarding the flow features around the train, two-main counter-rotating vortices are captured in the wake. Moreover, the higher the nose length and the higher the bluntness angle γ, the weaker and narrower the wake. Again, a longer nose shape yields to a softer jump in terms of pressure difference, crucial for train homologation and safety.

This literature review investigates the role of plumage in the hunting tactics of Velociraptor, integrating anatomical analysis and biomechanical modeling. Velociraptor, a swift and agile theropod from the Late Cretaceous, exhibited advanced intelligence and sensory capabilities that contributed to its effective predatory strategies. Recent discoveries have confirmed that Velociraptor was covered in feathers, with quill knobs indicating well-developed plumage. This review explores the potential functions of feathers beyond flight, focusing on their impact on hunting behavior. Evidence suggests that Velociraptor’s plumage likely facilitated camouflage and enhanced aerodynamic control, improving its stealth and maneuverability during high-speed chases. Additionally, feathers might have contributed to stability during incline running, further supporting its adaptability in diverse environments. Velociraptor’s hunting strategies, characterized by agility and precision, were complemented by its feathered anatomy, which may have also played a role in pack hunting and social interactions. Overall, the integration of plumage with Velociraptor’s anatomical features and behavioral adaptations underscores its efficiency as a predator, demonstrating how feathers may have been a critical factor in its successful hunting tactics.

Constructing a globally consistent high-precision map is essential for the application of mobile robots. Existing optimization-based mapping methods typically constrain robot states in pose space during the graph optimization process, without directly optimizing the structure of the scene, thereby causing the map to be inconsistent. To address the above issues, this paper presents a three-dimensional (3D) LiDAR mapping framework (i.e., BA-CLM) based on LiDAR bundle adjustment (LBA) cost factors. We propose a multivariate LBA cost factor, which is built from a multi-resolution voxel map, to uniformly constrain the robot poses within a submap. The framework proposed in this paper applies the LBA cost factors for both local and global map optimization. Experimental results on several public 3D LiDAR datasets and a self-collected 32-line LiDAR dataset demonstrated that the proposed method achieves accurate trajectory estimation and consistent mapping.

Chronic stress, culminating in burnout, evolves gradually and is notoriously difficult to detect due to vague symptoms and individuals' hesitance to acknowledge their struggles. To expedite the identification and recognition of this condition, enabling timely psychological intervention, the integration of Artificial Intelligence (AI) is increasingly considered. This research does not assert the feasibility of an AI system managing all aspects of chronic stress's impact. However, it highlights the capability of current technology to detect stress indicators based on quantifiable data like Heart Rate (HR) and organizational climate dimensions. Although other physiological markers such as oximetry, skin galvanic response, and EKG have been explored, they have not shown reliable differentiation between stress and joy. Focused on the unique context of school principals in the Bedouin regions of Israel, this study investigates the interplay between HR, organizational climate, and stress levels. It introduces a novel application of a fuzzy logic tool that combines HR and organizational climate metrics to aid in stress diagnosis. This tool incorporates the psychologist's expertise to provide real-time data crucial for developing effective coping strategies. While the AI-supported fuzzy system does not replace professional psychological intervention, it significantly enhances the speed of condition identification and intervention planning, thus shortening the response time to stress-related issues in educational leadership within culturally specific settings. The application of such AI-driven tools is pivotal for sustaining the well-being and effectiveness of educational leaders, thereby supporting the broader goal of educational sustainability.

Polyetheretherketone is a promising material for implants due to its good mechanical properties and excellent biocompatibility. Its accessibility to a wide range of applications is facilitated by the ability to process it with an easy-to-use manufacturing process such as Fused Filament Fabrication. The elimination of disadvantages associated with the manufacturing process, such as a poor surface quality, is a main challenge to deal with. As part of the mass finishing process, centrifugal disc finishing has demonstrated good results in surface optimization, making it a promising candidate for post-processing of additively manufactured parts. The objective of this study is to identify the key parameters of the centrifugal disc finishing process on the waviness of additively manufactured PEEK specimen, which has not been investigated yet. Waviness of the specimen was investigated by means of confocal laser scanning microscopy (CLSM), while weight loss was additionally tracked. Six parameters were investigated: type, amount and speed of media, use of compound, amount of water and time. Type of media, time and speed were found to significantly influence waviness reduction and weight loss. Surface electron microscopy images demonstrated the additional effects of deburring and corner rounding. Results on previous studies with specimens made of metal showed similar results. Further investigation is required to optimise waviness reduction and polish parts in a second post-processing step.

The emergence of antimicrobial resistance (AMR) Candida auris presents a formidable global health challenge, causing severe healthcare-associated infections with high mortality rates. Its ability to colonize surfaces and resist standard disinfectants undermines traditional hygiene practices, prompting an urgent need for novel strategies. Ultraviolet C (UVC) light offers a promising approach due to its rapid and broad-spectrum germicidal efficacy. This review comprehensively examines the current knowledge of UVC LED technology in combating C. auris, highlighting its effectiveness, limitations, and potential applications in healthcare hygiene. UVC light has potent activity against C. auris, including multidrug-resistant (MDR) strains. UVC can reduce C. auris on contaminated surfaces, aiding in transmission prevention. This review explores implementation strategies, including mobile UVC systems for targeted disinfection of high-risk areas and equipment, integration into air handling units (AHUs) to continuously disinfect recirculating air, and incorporation into water treatment systems. Current limitations in our understanding of UVC safety and effectiveness necessitate further research to optimize application protocols and ensure treatment safety while maintaining efficacy against C. auris. Integrating UVC disinfection technology into infection control programs holds promise for strengthening hygiene practices that will curb the global spread of C. auris and improve patient outcomes.

The purpose of this study was to establish the association between total and segmental body composition (BC) variables and anaerobic performance and to create optimal models that best predict such performance in CrossFit® (CF) athletes. Fifty athletes, 25 males and 25 females (age: 33.26 ± 6.81 years; body mass: 72.57 ± 12.17 kg; height: 169.55 ± 8.71 cm; BMI: 25.06 ± 2.31 kg·m−2) were recruited to participate and underwent BC analysis using dual-energy X-ray absorptiometry (DXA) and an all-out laboratory test on a cycle ergometer (Wingate) to determine their anaerobic performance. The results show a significant correlation between BC values and performance, ranging from moderate (r = -0.34, p = 0.015) to near-perfect (r = 0.96, p &lt; 0.01). Furthermore, the created performance prediction models exhibited predictive capacities ranging from 19% (p = 0.017) to 93% (p &lt; 0.001). All prediction models were created using total or segmental lean mass variables, excluding others. BC and performance variables found significant differences between males and females. The findings demonstrate that BC variables are crucial indicators of anaerobic performance in CF athletes. Professionals responsible for athlete performance should use this information to monitor athletes and design training programs.

This article investigates and studies the current situation of implementing the credit system in ordinary high schools in Zhejiang Province, and puts forward relevant suggestions. Firstly, analyze the background and objectives of implementing the credit system in ordinary high schools in Zhejiang Province. Then, through a questionnaire survey method, a sample survey was conducted on the current status of the implementation of the credit system in ordinary high schools in Zhejiang Province. The results showed that there are some problems in the management of the credit system in schools, such as unreasonable credit course settings, inaccurate recording and statistics of credits, etc. Further analysis reveals that students and parents have biases and utilitarian motives in their understanding and evaluation of the credit system.

The research presented in the article is devoted to the study of the influence of phase compounds on the friability of the Fe-Si-Mn-Al complex alloy. The urgency of the problem lies in the development of technology for producing a non-scatterable alloy from manganese-containing ores and high-ash coals. The main goal of the work is to determine the range of alloy compositions and the resulting phases that affect the dispersibility of the alloy, which is critically important for its industrial implementation. Research methods include thermodynamic diagram analysis (TDA) using data on the standard enthalpy of formation of intermetallic compounds, as well as experimental tests in an ore-thermal electric furnace with a capacity of 200 kV*A. The results show that Fe-Si-Mn-Al complex alloys form a variety of silicide and aluminide phases, including intermetallic compounds and ternary systems, which is critical for understanding and controlling their physicochemical properties. When smelting a complex alloy, the content of leboite (Fe3Si7) in the Fe-Si-Mn-Al system plays a significant role. The development of smelting technology will be aimed at avoiding the FeSi2-Fe3Si7-F2(FeAl3Si2)-Mn11Si19 tetrahedron area. This approach to controlling the composition of a complex alloy is critical to ensuring its consistent friability properties in industrial applications. Thus, this work represents an important step in understanding the physical properties and stability of Fe-Si-Mn-Al complex alloys, which have potential for widespread use in metallurgical and other industrial applications.

High temperature Ni-superalloys are limited by reliance on critical elements and complex processing steps. High entropy alloys (HEAs) have demonstrated stable single/dual phase microstructures with strong ordering tendencies. A dual phase (FCC+BCC) Al0.5Co0.5CrFeNi1.5Ti0.25 alloy (developed using CALPHAD) was tested for room and high temperature compression behavior. The microstructure mainly comprises of coarse ordered FCC(L12) surrounding decomposed lamellae of ordered FCC(L12) and BCC(L21) phases, which coarsened upon annealing at high temperature (1100 °C) into a bi-continuous structure of disordered FCC+BCC(B2). Additionally, cold rollability of the cast alloy increased from &lt;5% to ~40% after annealing, with a corresponding softening observed in room temperature compression mainly due to disordering of FCC and BCC phases. Peak flow stresses of 793.45MPa, 535.12MPa, and 324.40MPa were achieved at 800oC, 900oC, and 1000oC respectively for the high temperature annealed alloy.

Diffusion magnetic resonance imaging (dMRI) is an imaging technique that provides information on the microstructural organization of biological tissue. dMRI allows for non-invasive visualization and quantitative assessment of white matter architecture in the brain by characterizing restrictions on the random motion of water molecules. Ultra-high field MRI scanners, such as those operating at 7 Tesla (7T) or higher, can boost signal-to-noise ratio (SNR) to improve dMRI compared with what is attainable at conventional field strengths such as 3T or 1.5T. However, at 7T wavelength effects cause lower transmit magnetic field efficiency in the human brain, mainly in the posterior fossa region, manifesting as signal dropouts in this region. Recently, we reported a simple approach of using a wireless radiofrequency (RF) surface array to improve transmit efficiency and signal sensitivity at 7T. Here we demonstrate the feasibility and effectiveness of using this RF enhancer for in-vivo dMRI at 7T. The use of the RF enhancer can effectively recover signal dropouts in the regions with intrinsically lower SNR such as cerebellum, leading to a better depiction of principal fiber orientations and enhanced visualization of extended tracts to the brainstem and pons enabling more comprehensive delineation of the full white matter architecture.

Plantar fasciitis is one of the most common causes of foot pain; in a significant percentage it is also associated with bone edema of the heel. A prospective randomized clinical trial was designed, in which 48 patients suffering from plantar fasciitis, with or without bone edema, were treated with temperature controlled high energy adjustable multi-mode emission laser and exercises (laser group) or with exercises only (control group). Patients were evaluated at recruitment (T0), at 2 (T1) and 6 months (T2), monitoring pain (with Visual Analogue Scale), functionality (with Foot Function Index) and perception of improvement (with Roles and Maudsley Score) and fascia thickness (with ultrasound examination). In both groups there was a significant improvement in pain, functional recovery, perception of remission and a reduction in plantar fascia thickness at T1 and T2. The laser group presented statistically better values at T2 for the Roles and Maudsley Score (z: 2.21; 0.027). Regression analysis showed that a greater reduction in fascia thickness occurred in the laser group (p-value: 0.047). In conclusion, the two conservative treatments were effective in patients suffering from plantar fasciitis, even in the presence of bone edema, but with lesser results.

In order to serve the online monitoring of the aging state of high-voltage (HV) cables, a novel method based on impedance spectroscopy has been proposed. Firstly, the method uses the Debye model to restore the dielectric response of the insulating material from the mechanism. Secondly, based on the transmission line equation, a calculation model for the impedance spectroscopy of HV cables was established. Then, the characteristics of the impedance spectroscopy under different overall aging and local deterioration states were analyzed. Further, the simulation analysis of the influence of factors such as load factor, length, metal resistivity, and geometric parameters on the impedance spectroscopy was carried out. Finally, diagnostic criteria were proposed, which are divided into two major categories: known cable parameters and unknown cable parameters. If the geometric parameters are known, the aging state can be determined using the resonance peak values and the resonance peak frequencies. If the geometric parameters are unknown, it is necessary to test the impedance spectroscopy in the healthy condition of the cable as the baseline curve. By comparing the impedance spectroscopy of the cable under test with the baseline curve, the aging development trend of the cable can also be determined.

In a new construction of a seventeen-storey building, it is necessary to remove a prop on the second floor, which has made it possible to complete the structure of the building. In the drafting of the executive project, no security measures were described, because it was understood that they were not necessary. In the construction phase, the need to monitor the process was raised, and to be able to stop it, or reverse it if necessary. It is a reinforced concrete structure, with metal elements and composite elements, with a torsional behavior of the cores making the slabs serve as horizontal diaphragms, so the final behavior could be different from what was expected. To make this process possible, two pairs of four metallic cantilevers were introduced into which four Hydraulic pistons were inserted. Before starting the process, they were loaded to be sure that they would not fail. Strain gauges were also placed to control the stresses and how the situation changed during the unshoring process. The process of cutting the provisional pillar was a success, obtaining less deformations than expected, having a complementary safety.

In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.

Daily vitamin D supplementation using higher than normal dosing (up to the upper limit, UL) and intermittent (once or twice per week) dosing were studied in patients with increased risk of vitamin D deficiency. Using a PubMed database an adequate search for published randomized control trials and other studies was done and results were analyzed. This review provides overview of use of 7000 IU daily, 30,000 IU per week or twice weekly and 50,000 IU weekly of vitamin D on rapid restore of 25(OH)D concentrations to at least 30 ng/mL in different groups of patients at high risk of vitamin D deficiency. The above mention dosing should be considered in adults with obesity or multi-diseased patients on requiring multi-treatment with the use of several drugs, including drugs affecting vitamin D metabolism. The simple schedule for 7000 IU/day, 30,000 IU/week or twice weekly or 50,000 IU/week, all for 6-8 weeks of use by patients representing the increased risk of vitamin D deficiency were provided for consideration. It appeared that higher daily doses or intermittent doses suggested above are effective, safe and responsive for patient’s preferences.

When water molecules or other particles collide with protein molecules in a solution, the protein molecules absorb some of the momentum and deform, forming a certain molecular potential energy. When a protein molecule in a high-energy state changes to a stable state, if there is a suitable substrate binding and the potential energy of the protein molecule is greater than the energy required to break the substrate chemical bond, catalytic action will occur. The α-helices and β-folds in protein molecules play a major role in converting the kinetic energy of water molecules into their own potential energy due to the large number of amino acids involved and their regular structure. The internal structural deformation of proteins caused by the impact of water molecules on α-helices and β-folds also has a profound impact on the structure of substrates. ‌

This article provides a literature review on tubal carcinoma to offer an updated insight into its preventative strategies, diagnosis, treatment, and oncological surveillance. In addition to the search string utilized, the authors' focus extended to key scientific studies, consensus statements, guidelines, and relevant case reports essential for the proper clinical management of the disease, providing a methodologically well-structured literature review combined with the practical expertise in the oncological field. The article also includes two emblematic clinical cases that emphasize the importance of understanding the physiopathology and the current state of the art in the anatomopathological advancements of tubal/ovarian/peritoneal carcinoma, often assimilated into a single clinical entity.

A high-gain broadband circularly polarized crossed dipole antenna is designed. This antenna utilizes two pairs of cross dipoles and a pair of phase delay lines to form circularly polarized radiation. Open-circuit stubs are loaded on the four arms of these two pairs of cross dipoles to introduce new circularly polarized resonating frequency. A rectangular ring patch is introduced directly below the cross dipoles to form the third circularly polarized resonating frequency, thereby broadening the axial ratio bandwidth of the antenna. In addition, metal posts are loaded at the four right angles of the rectangular ring patch to increase the antenna gain. Measurement results show that the antenna achieves a 3dB axial ratio bandwidth of 29.2% (1.9 GHz-2.55 GHz) and maintains a gain of 7.5 dB within the passband, exhibiting good circularly polarized radiation performance.

Glioblastoma is a highly aggressive brain tumor and is considered to be the most common primary one. Recurrence after treatment is a major problem. The recurrence of GBM is related to different cellular mechanisms and molecular signaling. Therapies to prolong survival are not completely effective. Epigenetics and non-coding genetic elements play a crucial role in gliomagenesis. Non-coding RNAs are novel regulatory RNAs that play key roles in different physiological processes such as gene regulation, cell differentiation, and proliferation. Interestingly, some LncRNAs have a tumor suppressor role while others are oncogenic. In this review article, we are going to illustrate the role of a well-known lncRNA HOX transcript antisense intergenic RNA (HOTAIR) in glioma and highlight the possible functions in glioma in both pre-clinical and clinically evident studies.

The Hyper-Torus Universe Model (HTUM) proposes a novel framework to unify quantum mechanics, cosmology, and consciousness. This paper introduces HTUM's core concept: a higher-dimensional hyper-torus encompassing all possible states of existence. HTUM suggests that the universe functions as a quantum system where all outcomes are inherently connected, with consciousness playing a significant role in actualizing reality. The model introduces several key innovations, including the universe's 4-dimensional toroidal structure (4DTS), providing a new geometric interpretation of spacetime. HTUM presents dark matter and dark energy as nonlinear probabilistic phenomena within this toroidal framework, offering a unique perspective on their nature and interactions. The model proposes a mechanism for wave function collapse through universal self-observation, bridging quantum mechanics and gravity. It introduces a Topological Vacuum Energy Modulator (TVEM) function, offering a potential resolution to the cosmological constant problem. Furthermore, HTUM integrates consciousness as a fundamental aspect of the universe, influencing quantum state actualization and potentially resolving the hard problem of consciousness. The model explores the implications of a timeless singularity and the emergence of time as a product of causal relationships within the toroidal structure. This framework addresses critical challenges in modern physics, including the nature of quantum entanglement, the origin and fate of the universe, and the relationship between mind and matter. The paper discusses the mathematical formulation of HTUM, its implications for quantum mechanics and cosmology, and its potential to bridge the gap between science and philosophy. We present detailed predictions for the cosmic microwave background (CMB) power spectrum, gravitational wave signatures, and large-scale structure formation, demonstrating how HTUM differs from the standard ΛCDM model. Our analysis reveals distinctive oscillatory patterns in the relative difference between HTUM and ΛCDM predictions, with deviations reaching up to ±20% at certain scales. The paper also explores the unification of fundamental forces within the HTUM framework, proposing novel approaches to particle physics and quantum field theory. It introduces the concept of unified mathematical operations, suggesting a more holistic approach to mathematical thinking that aligns with the model's interconnected view of the universe. Additional testable predictions and proposed experimental approaches are discussed, including advanced space-based tests and laboratory experiments probing quantum gravity effects. These specific, quantifiable predictions offer multiple avenues for empirical validation, highlighting HTUM's potential to be distinguished from ΛCDM and other alternative cosmological models. HTUM represents a significant new perspective in our understanding of the universe, inviting further research and exploration into the nature of reality, consciousness, and the fundamental structure of the cosmos. By providing a comprehensive framework that unifies various aspects of physics, cosmology, and consciousness studies, HTUM offers a promising path toward a more complete understanding of our universe.

Background/Objectives: Encouraging results reported of Platelet-Rich Plasma (PRP) treatment for knee osteoarthritis (KOA). The present retrospective study reports the efficacy and safety of a high dose of neutrophile and red blood cell-depleted PRP to treat 212 patients with KOA. Methods: 212 consecutive patients diagnosed with Kellgren-Lawrence (KL) grading 1-3 KOA chronic knee pain for at least 1 year were treated with 3 injections at 15-day intervals with a high dose of neutrophil-depleted PRP (4 billion platelets). Clinical outcomes were retrospectively recorded as a percentage of responders at 3,6, and 12-month follow-up, following the OMERACT-OARSI criteria. Pain through VAS score and WOMAC score have also been recorded. Results: 4ml of PRP containing 4X109 platelets were obtained by single spin centrifugation and injected intra-articular into each patient with no pre-activation. The overall responder rate of patients responding to OMERACT-OARSI criteria at 3,6,12 months was 68.9%, 72,7% and 70,6%. There was a significant improvement in VAS and WOMAC scores at 3-, 6- and 12-month follow-up compared to the pre-treatment value (p&lt; 0.01). The lowest VAS score was observed at 6 months overall and in all three-grade KL groups. KL2 groups showed the best results regarding pain reduction and WOMAC score at 6 months (p&lt; 0.01). Conclusions: a high dose of neutrophil-depleted PRP is an effective treatment for KL1-3 KOA. It provides symptomatic relief, can potentially reduce disease progression, and has sustained effects for up to 12 months.

Background: Chronic exposure to severe hypoxia causes an increase in hematocrit (Hct) and hemoglobin concentration ([Hb]), which can lead to Excessive Erythrocytosis (EE), which could impact physical performance. This work aims to determine the differences in the six-minute walking test (6MWT) outputs between EE and healthy subjects residing at more than 5000 meters. Methods: A prospective, cross-sectional study was performed on 71 men (36 healthy and 25 suffering EE) living in La Rinconada, Peru (5100 m). Basal levels of [Hb] and Hct were obtained. All the subjects per-formed the 6MWT, and distance reached, vital signs, dyspnea, and fatigue (Borg scale) at the end of the test were recorded. Results: The average [Hb] and Hct levels in the control group were 18.7 ± 1.2 g/dL and 60.4 ± 7.1%, respectively, contrasting with EE subjects who showed 23.4 ± 1.6 g/dL and 73.6 ± 5.9% (p < 0.001). However, no statistically significant differences were observed in BMI or other anthropometric parameters. At the end of the 6MWT, the distance traveled, and vital constants were similar between both groups, except for arterial oxygen saturation which was consistently lower in subjects with EE along the test. Conclusion: EE does not significantly affect 6MWT performance at high altitudes nor the hemodynamic control during moderate aerobic exercise of subjects who live permanently in a severe hypoxic environment.

This study explores the effects of tempering on the precipitation behavior and impact toughness of high-nickel steel. The specimens underwent double quenching at 870°C and 770°C, followed by tempering at various temperatures. Advanced characterization techniques including optical microscopy (OM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were used to elucidate precipitation phenomena. Additionally, electron backscatter diffraction (EBSD) was employed to assess the misorientation distribution after tempering. Charpy impact tests were performed on specimens tempered at different temperatures to evaluate their toughness. The findings reveal that with increasing tempering temperature, the fraction of low-angle grain boundaries decreases, which correlates positively with enhanced impact toughness. The impact toughness peaks at 580°C and then diminishes with further temperature increases.

In the realm of high-pressure vessel simulation, conventional finite element method (FEM) approaches, as per ASME standards, may inadequately predict the behavior of flat surfaces under elevated temperatures. This study challenges the efficacy of shell-type mesh modeling for high-temperature flat plates, demonstrating that the thermal conditions within such high-pressure vessels can induce thermal instability and buckling, not accounted for by traditional FEM methods recommended by ASME. Through comprehensive analytical investigations, we reveal that traditional shell-type meshing techniques, while suitable for certain applications, fail to capture the intricate thermal stresses and deformation patterns inherent in high-temperature flat plate configurations. Our analysis delineates distinct stability regimes governed by key design parameters—including plate thickness, operating temperature, and geometric dimensions—profoundly impacting the structural integrity of heating plates under thermal loading. By elucidating these stability boundaries, this research provides engineers with critical insights necessary for optimizing the design and performance of high-temperature equipment. This includes the design of high-pressure vessels with flat surfaces for heating materials, flanges in high-temperature environments, and fins in heat exchangers across various industries such as oil and gas, pyrolysis, and power plants. The findings presented herein serve as a valuable reference for engineers seeking to comprehend and mitigate instability phenomena in solid mechanics, offering practical guidance for developing robust and reliable high-temperature structures in demanding industrial environments.

Succinate is proposed to be a mediator of muscle exercise-induced adaptations. We studied metabolic health and changes of muscle mass in 6-month-old male mice after 12 weeks of feeding regular diet (RD, 13.4 kcal% fat, 66.8 kcal% carbohydrate, 29.8 kcal% protein), high fat diet (HFD, 60 kcal% fat, 20 kcal% carbohydrates, 20 kcal% protein) and ketogenic diet (KD, 80 kcal% fat, &lt;1 kcal% carbohydrates, 20 kcal% protein) with or without 2% succinate supplements (SUS) in drinking water (n=8-12 per group). Functional overloading of the plantaris muscle (PL) was induced in a group of mice by denervation of the gastrocnemius and soleus muscles at week 6 of feeding different diets. HFD induced the greatest (p &lt; 0.001) increase in body and fat mass. HFD and KD lead to significant (p &lt; 0.01) impairment in glucose tolerance compared to RD. SUS blunted (p &lt; 0.01) initial surge in energy intake when mice were switched from RD to HFD, but did not influence any measures of metabolic health after 12 weeks of the study. Functional overloading lead to ~25% increase in PL mass which was not affected by diet or SUS. In conclusion, SUS does not have a long-term effect on metabolic health or muscle mass.

This study investigates the effect of oil viscosity on pollutant emissions and fuel consumption of an internal combustion engine (ICE) in high-altitude using Response Surface Methodology (RSM). A Chevrolet Corsa Evolution 1.5 SOHC gasoline engine was used in Cuenca, Ecuador (2560 meters above sea level), testing three lubricating oils with kinematic viscosities of 9.66, 14.08, and 18.5 cSt under various engine speeds and loads. Key findings include: hydrocarbon (HC) emissions were minimized to 7.25 ppm with low viscosity and load; carbon dioxide (CO2) emissions peaked at 15.2% vol with high viscosity and load; carbon monoxide (CO) ranged from 0.04% to 3.74% depending on viscosity and load; nitrogen oxides (NOx) were significantly influenced by viscosity, RPM, and load, indicating a need for model refinement; and fuel consumption was significantly affected by load and viscosity. RSM-based optimization identified optimal operational conditions with a viscosity of 13 sCt, 1473 rpm, and a load of 78%, resulting in 52.35 ppm of HC, 13.97% vol of CO2, 1.2% vol of CO, 0 ppm of NOx, and a fuel consumption of 6.66 l/h. These conditions demonstrate the ability to adjust operational variables to maximize fuel efficiency and minimize emissions. This study underscores the critical role of optimizing lubricant viscosity and operational conditions to mitigate environmental impact and enhance engine performance in high-altitude environments.

ATTO 565, a Rhodamine-type dye, has garnered significant attention due to its remarkable optical properties, such as a high fluorescence quantum yield, it is a relatively stable structure, and has low biotoxicity. ATTO 565 has found extensive applications in combination with microscopy technology. In this review, the chemical and optical properties of ATTO 565 are introduced, along with the principles behind them. Then, the functionality of ATTO 565 in confocal microscopy, stimulated emission depletion (STED) microscopy, single-molecule tracking (SMT) techniques, and fluorescence correlation spectroscopy (FCS) is discussed. These studies demonstrate that ATTO 565 plays a crucial role in areas such as biological imaging and single-molecule localization, thus warranting further in-depth investigation. Finally, we present some prospects and concepts for the future applications of ATTO 565 in the fields of biocompatibility and metal ion detection.

Overconsumption of an unbalanced diet and overweight, leading to insulin resistance, dyslipidemia, hepatic steatosis, cardiovascular diseases and obesity, is nowadays a worldwide health issue, with different patterns of metabolic disturbances in the young and adult popula-tions, in both gender. Preclinical models that closely mimic the gradual weight gain that occurs in humans upon consumption of a “western-type” diet (WD) are of great interest. In particular, the diet-induced obesity (DIO) model in the C57BL/6J mouse sub-strain is often used in biomed-ical research, considering that it is prone to metabolic disorders and obesity, and is widely used to generate genetically modified mice. This study aimed to phenotypically characterize the C57BL/6J mouse strain fed a WD-like diet, using high-frequency ultrasound imaging (HFUS) as a complementary tool to longitudinally monitor morphofunctional changes in the liver, heart and kidney associated with DIO. Long term WD feeding increased mice body weight (BW), liver/BW ratio and body condition score (BCS), serum transaminases, glucose and insulin, as well as Homeostasis model assessment (HOMA) indexes, and caused dyslipidemia and insulin resistance. According to the 3Rs, ultrasound imaging has enabled a comprehensive study of metabolic syndrome in mice, in vivo and non-invasive, improving the identification of early stages of diseases.

Physics-informed neural networks can be trained to serve as surrogate models by learning how spatial physical fields develop with change of parameters. This is an advantage over traditional numerical methods that can only be used to calculate a single solution field for a single discrete setting of a parameter. While many studies report accurate results of physics-informed deep learning of laminar flows, evaluations of surrogate modeling of high Reynolds number flows remain sparse. To contribute to this question, we here explore the capabilities and limits of physics-informed deep learning to solve the Reynolds-averaged Navier-Stokes equations for the flow around two airfoils under variable angles of attack. No labeled training data were provided and a single network was trained to simultaneously learn several solution fields in a single training run. The network captured essential flow features such as boundary layers and high and low pressure regions. Moreover, the qualitative correlations of lift and drag with the angle of attack and the higher drag of the thicker airfoil were captured. However, comparisons with reference simulations revealed an underestimation of the shear layer gradients as well as deviations of the fields' extrema. Thus, we also debate potential future improvements to increase the accuracy of the predicted flow. This work offers a prospect on the capabilities and current limitations of physics-informed neural networks for surrogate modeling of high Reynolds number flows. We argue that the method is promising and this work is aimed to encourage further research and development of the method when applied to Reynolds-averaged flows at high Reynolds numbers.

Gestational Diabetes Mellitus (GDMs) is worldly wide pregnancy complication. Gestational Diabetes can significantly impact the fetus development. However, the effects of high glucose on embryological development post-fertilization are yet to be researched. Danio rerio embryos are great model to study the embryonic development. In this study, the effects on embryological (morphological and genetic) development were examined in the presence of a high glucose environment that mimic the developing fetus in pregnant women with GMD. Fertilized Zebrafish embryos were treated with normal media and high glucose for 5 days from 3 hours post-fertilization(hpf) to 96hpf respectively as control and experimental groups. Morphological changes are recorded with Microscope images. Hatch rate and heart rate are compared between groups in set up time points. RNA-Seq is performed to examine the gene changes in experimental group. Glucose delayed the zebrafish embryo development by slowing the hatch rate about 24 hours. The brain, heart, and tail started showing morphology smaller in the glucose group compared to the control group at 24 hpf. Heart rate is faster in the glucose group compared to the control group on day 2 and 3 with a statistically significant difference. Among zebrafish whole genome, the significantly changed genes are 556 genes up-regulated and 1118 genes down-regulated respectively in high glucose group. The metabolic and Wnt pathways are altered under high glucose condition. These conditions contribute to significant physiological differences that may provide insight on functionality post-embryological development.

We present an analysis of high-resolution, near-infrared (NIR) spectra relative to the solar transit of Venus of 5-6 June 2012, as observed with the Facility Infrared Spectropolarimeter (FIRS) at the Dunn Solar Telescope in New Mexico. These observations offer the unique opportunity to probe the upper layers (between ∼84 and 150 km in altitude) of a thick, CO2-dominated atmosphere with the transmission spectroscopy technique – a proxy for future studies of highly-irradiated atmospheres of Earth-sized exoplanets. We were able to visually identify absorption lines from the two most abundant CO2 isotopologues, and from the main isotopologue of CO in the retrieved spectrum of Venus. Furthermore, we perform a cross-correlation analysis of the transmission spectrum using transmission templates generated with petitRADTRANS. With the cross-correlation technique, it was possible to confirm detections of both CO2 isotopologues and CO. Additionally, we retrieve a cross-correlation signal for O3 on Venus. We demonstrate the feasibility of high-resolution, ground-based observations to study the chemical inventory of planetary atmospheres, employing techniques commonly used in exoplanet characterization.

Gas-water relative permeability curve is the foundation of gas reservoir dynamic analysis and numerical simulation. It is generally obtained through gas displacing water experiment. Referring to the existing national standards, gas-water relative permeability test is carried out for low-permeability and tight sandstone. The flow is discontinuous and the curve smoothness is poor, which affects the application of gas-water relative permeability curve. Based on the comparative analysis of a large number of mercury injection and NMR experimental results of low-permeability and tight sandstone, a method to characterize the throat radius distribution of low-permeability tight sandstone based on NMR T2 spectrum is explored. Combined with high-speed centrifugal experiment, the calculation formulas of core water saturation, phase relative permeability of gas-water under different centrifugal force are established. A new method of "nuclear magnetic resonance + high-speed centrifugation" for gas-water relative permeability curve test of low-permeability and tight sandstone is formed, and the test is carried out on Sulige low-permeability tight sandstone core. The results show that: (1) The shape of cumulative distribution curve of throat radius by mercury injection method is basically consistent with that of T2 relaxation time by NMR, and there is a good corresponding relationship between them. (2) The centrifugation process is similar to the gas displacing water process. With the decrease of water saturation, water centrifugation in rock core becomes more and more difficult until it become irreducible. (3) The test process of the new method is unified and standard and up to 6 cores can be tested at the same time. The calculation results of water saturation and relative permeability curve are reliable and the integral curve is smooth, which greatly improves the test efficiency of gas-water relative permeability curve in low-permeability and tight sandstone. The new method can be widely used to study the gas-water two-phase seepage law in low-permeability and tight sandstone gas reservoir.

In mountain-gorge areas, the rock creep is the critical process for high rock slopes failure. During long-term rock creep, slopes might encounter earthquakes and form further creep after earthquakes. This complex mechanical response process can easily lead to the slope failure. Based on a high rock slope in the Nujiang River Basin, this paper analyzes deformation characteristics and dynamic response characteristics by using FLAC3D software, considering combined effects of multiple earthquakes and long-term creep. Results show that when the amplitude increases, the shear strength of the slope decreases and the risk of instability increases under combined actions of creep and earthquakes. Earthquakes promote the development of creep and induce the accumulation of damage on the slope surface and in the slope. The delayed effect becomes more pronounced as the slope height increases. We need to consider deformation differences of the slope further. The ground motion response on the slope surface is stronger than those in the slope, with the peak occurring at the top of the slope. Earthquakes have a greater impact on the middle and top of the slope surface, where cumulative damage and crack development begin. Reinforcement should be considered in these two places. Vertical earthquake has a great effect on the dynamic response. The phenomenon of slope resonance leads to a larger MPGA in the vertical direction than in the horizontal direction. Nonlinear and damping characteristics of the slope and the frequency of seismic waves cause the MPGA to decrease with the increase of amplitudes. This study could promote the development of high rock slope failure mechanism and provide references for the prevention of landslides in the Nujiang River Basin.

Knee osteoarthritis (KO) is an important health condition, affecting one third of the people aged 65 years or more. Pain is the main cause of disability. Pain management in KO includes pharmacological and non-pharmacological modalities. Patient education, lifestyle changes, physical exercise and physical agents are prescribed as a first approach for pain control. Laser therapy is part of many therapeutical protocols, with two forms, low-level laser therapy (LLLT) and high-intensity laser therapy (HILT). The paper aimed at stressing the advantages of HILT, based on a greater wavelength, higher energy delivery and deeper tissue penetration. Research on 23 published trials revealed that analgesic effect is rapid, cumulative and long lasting. Compared to sham, to LLLT or to other associations of therapeutical modalities, HILT provided significantly better results on pain reduction and functional improvement. Ultrasound examination showed reduction of intraarticular inflammation.

There are few results about the internal damping ratio of normal and high strength concretes. Hence, this paper presents the expansion of the investigation about internal damping ratio under undamaged and damaged conditions, for usual concretes (NSC) and high strength concretes (HSC). In this way, the study cover a strength range of 42 to 83 MPa. Cyclic load was employed by a servo-controlled hydraulic testing machine and for each cyclic step the dynamic elastic modulus (Ed) and internal damping ratio (ξ) were determinate by acoustic tests. Normal strength concretes (fc = 42MPa) presented undamaged internal damping ratio ξ = 0.5% and achieved the maximum value of ξ = 2.5 for a damage index equal to 0.8. High strength concretes mixtures (fc = 83MPa) presented an undamaged internal damping of ξ=0.29% and maximum internal damping equal to ξ=0.93% (under damage index of 0.32). Porosity and the transition zones were the responsible to the initial internal damping values and how the material behavior under each cyclic load. The progressive damage generates the increase of coulomb damping. There are few studies allowing the quantification and comprehension of internal damping ratio under damage cyclic loading and this approach will lead to improve the understanding of NSC and HSC under dynamical excitation subject to damage evolution, mainly in impact situations.