The work presents the results of numerical fatigue analysis of a turbine engine compressor blade, taking into account the values of initial stresses resulting from surface treatment - shot-peening. The values of the residual stresses were estimated experimentally using X-ray diffraction. The paper specifies the values of the residual stresses on both sides of the blade and their reduction due to the cutting through the blade - relaxation. The obtained values of the residual stresses were used as initial stresses in the numerical fatigue analysis of the damaged compressor blade, which is subjected to resonant vibrations of known amplitude. Numerical fatigue ε-N life analysis was based on the several fatigue material models: Manson’s, Mitchell’s, Baumel-Seeger’s, Muralidharan-Manson’s, Ong’s, Roessle-Fatemi’s and Median’s, and also on the three models of cyclic hardening: Manson’s, Xianxin’s, and Fatemi’s. Because of this approach, it was possible to determine the relationship between the selection of the fatigue material ε-N model and the cyclic hardening model on the results of the numerical fatigue analysis. Additionally, the calculated results were compared with the results of experimental research, which allowed for a substantive evaluation of the obtained results. These results are of great scientific and practical importance. The problem of determining the fatigue life of blades with defects operating under resonance vibrations is one of the original tasks in the field of fracture mechanics and experimental mechanics. The results obtained are of great importance in the aviation industry and can be used during engine maintenance and inspections to assess the suitability of blades with defects in terms of the needs of further work. This aspect of engineering maintenance is of great importance from the aircraft safety point of view.

Influential Observations, which are outliers in x direction, y direction or both, remain a hitch in classical regression model fitting. Spatial regression model, with peculiar nature of outliers due to their local nature, is not free from the effect of such influential observations. Researchers have adapted some classical regression techniques to the spatial models and yielded satisfactory results. However, masking or/and swamping remain stumbling block to such methods. We obtained the spatial representation of the classical regression measures of diagnostic in general spatial model. Commonly used diagnostic measure in spatial diagnostic, the Cook's distance, is compared to some robust methods, Hi2 (using robust and non-robust measures), and classification based on generalized residuals and diagnostic generalized potentials, ISRs-Posi and ESRs-Posi, with the help of the obtained spatial prediction residuals and the spatial leverage term. Results of simulation and applications to real data have shown the advantage of the ISRs-Posi and ESRs-Posi due to classification of outliers over Cook's distance and non-robust Hsi12, which suffer from masking, and robust Hsi22 which suffer from swamping in general spatial model.

Biofortification refers to the increase in the amount of essential vitamins or provitamins or minerals in crops to improve the nutritional status of the people, which is largely intended to alleviate the problem of micronutrient malnutrition. I argue that biofortification may not be an effective weapon to fight against the hidden hunger since it demonstrates limited capacity on nutritional enhancement and can negatively impact the socio-economic fabric of the society in many different ways. Finally, I suggest a couple of alternatives that might meet the challenge more efficiently than biofortified crops.

Background: The present retrospective study was designed to evaluate the relative diagnostic utility of breast-specific gamma imaging (BSGI) and breast magnetic resonance imaging (MRI) as means of evaluating female breast cancer patients in China. Methods: A total of 229 malignant breast cancer patients underwent ultrasound, mammography, BSGI, and MRI between January 2015 and December 2018 for initial tumor staging. Of these patients, 73 were subsequently treated via definitive breast surgery following neoadjuvant chemotherapy (NAC), of whom 17 exhibited a complete pathologic response (pCR) to NAC. Results: BSGI and MRI were associated with respective 76.8% and 69.6% sensitivity values as a means of detecting residual tumors following NAC, while both of these approaches exhibited comparable specificity in this diagnostic context (58.8% vs 70.6%, P=0.473). Conclusion: These results demonstrate that BSGI is a useful auxiliary approach to evaluating pCR to NAC treatment.

Pneumonia is a leading cause of death worldwide, and one of the most significant approaches to diagnose pneumonia is Chest X-ray (CXR) since it was used in clinical scenes. Convolutional neural networks (CNNs) have been widely used in computer vision community. Along with the development of CNNs, we want to make use of CNNs to recognize CXR of people who get pneumonia and make classification. It is important, especially during epidemic period. In this paper, we present a new type of residual learning framework, PEPX-Resnet, which makes use of a type of lightweight residual, and apply this network to CXR dataset. The result shows that PEPX-Resnet is easier to optimize and can have better results, especially for COVID-19 cases. PEPX-Resnet could reach higher accuracy, f1 score and some other evaluations for CXR dataset.

The article presents results of research consisting in an attempt to assess the influence of temperature, heating time and cooling method on microstructure and residual strength properties of steel previously tempered during the production process. Simulated environmental conditions to which high-strength bolts, commonly used in steel construction, were subjected, were intended to reflect conditions of a natural fire that may occur in public facilities where the obligation to ensure safety of users and rescue teams is of key importance, also required by law. Furthermore, the tests carried out also comprised a simulated effect of a rescue and firefighting operation using shock, rapid cooling of some of the heated bolts. Samples cut out from the tested bolts, after they were properly prepared, were subjected to microstructural tests using light microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), phase analysis with the use of an X-ray diffractometer (XRD) and quantitative analysis of the microstructure involving, inter alia, measuring the surface area of grains, their equivalent diameter and mean diameter. As a result of the tests, considerable microstructure changes were identified occurring in the bolt material as a result of exposing it to fire conditions, leading to a change in key, from the point of view of structural safety, mechanical properties. The results of the microstructure tests were compared with the results of previous strength tests, including hardness of the material after the heat treatment and the residual tensile strength of the material Rm. A conducted comparative analysis showed a significant effect of all such factors as the temperature level of the simulated fire, its duration and the fire-fighting method on the mechanical properties of bolts. Results obtained were provided with required comments and the concept of using the microstructure for the post-fire assessment of steel structures was referred to.

Over the years, leaked fluids from the aircraft caused severe deterioration of the airfield pavement. The combined effect of hot exhaust from the auxiliary power unit of military aircraft and spilt aviation oils caused rapid pavement spalling. If the disintegrated concreted pieces caused by spalling is sucked into the jet engine, it may cause catastrophic damage to the aircraft engine or physical injury to maintenance crews. This study investigates the effectiveness of incorporating hybrid fibres into ordinary concrete to improve the residual mechanical and thermal properties to prevent spalling damage of pavement. Three fibre reinforced concrete samples made with micro steel fibre and polyvinyl alcohol fibre with a fibre content of zero, 0.3%, 0.5% and 0.7% by volume fraction. These samples were exposed to recurring high temperature and aviation oils. Tests were conducted to measure the effects of repeated exposure on the concrete's mechanical, thermal and chemical characteristics. The results showed that polyvinyl alcohol fibre reinforced concrete suffered a significant loss of thermal properties and residual mechanical strength than the micro steel fibre reinforced concrete. However, hybrid fibre reinforced concrete performed better in retaining higher residual properties, and no spalling of concrete was observed.

Significant problems have arisen in the last years, such as climate change, global warming, and hunger. These complications are correlated with the depletion and exploitation of natural resources and environmental contamination. Due to overcrowding, the list of challenges for the next few years is growing. A comprehensive approach was made to the agro-industrial production of Avocado (Persea americana) and the management of all its biomass waste. So, bioprocesses and biorefinery can be used to produce high added-value products. A large number of residues are composed of lignin and cellulose. They have many potentials to be exploited sustainably for chemical and biological conversion; physical, chemical, and natural treatments improve the following operations. There are some applications to many fields such as pharmaceutical, medical, material engineering, and environmental remediation. Possible pathways are mentioned to take advantage of Avocado as biofuels, drugs, bioplastics, and even in the environmental part and emerging technologies such as nanotechnology using bioprocesses and biotech. In conclusion, Avocado and its waste could be transformed into high value-added products in industries above to mitigate global warming and save non-renewable energy.

The bending performance of a basalt-polypropylene fiber-reinforced concrete (HBPFRC) was characterized by testing 24 400×100×100 mm3 prismatic specimens in a four-point bending test JSCE-SF4 configuration. The type and content of both fibers was varied in order to guarantee different target levels of post-cracking flexural performance. The results evidenced that mono-micro basalt fiber reinforced concrete (BFRC) allows the increase of the flexural strength (pre-cracking stage), while macro polypropylene fiber reinforced concrete can effectively improve both bearing capacity and ductility of the composite for a wide crack width range. Compared with the plain concrete specimens, flexural toughness and equivalent flexural strength of macro polypropylene fiber-reinforced concrete (PPFRC) and the hybrid fiber-reinforced concrete (HFRC) increased by 3.7~7.1 times and 10%~42.5%, respectively. From both technical and economic points of view, the optimal mass ratio of basalt fiber to polypropylene fiber resulted to be 1:2, with a total content of 6 kg/m3. This HFRC is seen as a suitable material to be used in sewerage pipes where cracking control (crack formation and crack width control) is of paramount importance to guarantee the durability and functionality of the pipeline as well as the ductility of the system in case of local failures.

This study aimed at the investigation of the effect of substrate preheating on residual stress in laser powder bed fusion using a physics-based analytical model. In this study, an analytical model is proposed to predict the residual stress through the calculation of preheating affected temperature profile and thermal stress. The effect of preheating is super-positioned with initial temperature in the modeling of temperature profile using a moving heat source approach; the resultant temperature gradient is then employed to predict the thermal stress from a point body load approach. If the thermal stress exceeds the yield strength of the material, then the residual stress under cyclic heating and cooling will be calculated based on the incremental plasticity and kinematic hardening behavior of metal. IN718 is used as a material example to pursue this investigation. To validate the predicted residual stress, experimental measurements are conducted using X-ray diffraction on IN718 samples manufactured via laser powder bed fusion under different process conditions. Results showed that preheating of the substrate could reduce the residual stress in an additively manufactured part due to the reduction in temperature gradient and resultant shrinkage stresses. However, the excessive preheating could have an opposite impact on residual stress accumulation. Moreover, the results confirm that the proposed model is a valuable tool for the prediction of residual stress- eliminating the costly experiments and time-consuming finite element simulations.

The bio-oil obtained by pyrolysis of Açaí (Euterpe oleracea Mart.) seeds at 450 ºC, 1.0 atmosphere, in technical scale, submitted to fractional distillation to produce biofuels-like fractions. The distillation of bio-oil carried out in a laboratory distillation column (Vigreux) of 30 cm. The physical-chemistry properties (density, kinematic viscosity, acid value and refractive index) determined by official methods. The chemical functions present in distillation fractions determined by FT-IR and the chemical composition by GC-MS. The distillation of bio-oil yielded gasoline, light kerosene, and kerosene-like fuel fractions of 16.16, 19.56, and 41.89% (wt.), respectively. All the physical-chemistry properties (density, kinematic viscosity, acid value and refractive index) increase with boiling temperature. The gasoline-like fraction is composed by 64.0% (area.) hydrocarbons and 36.0% (area.) oxygenates, while light kerosene-like fraction by 66.67% (area.) hydrocarbons and 33.33% (area.) oxygenates, and kerosene-like fraction by 19.87% (area.) hydrocarbons and 81.13% (area.) oxygenates.

There is consensus that climate variability and change is impacting food security in Eastern Africa, and that conventional extension approaches, based on top-down model of information dissemination and technology transfer, are too inadequate to help smallholder farmers tackle increasingly complex agro-climatic adversities. Innovative service delivery options exist but are mostly operated in silos with little effort to explore and blend them. There are efforts to develop a blended Climate-Resilient Farmers Field School methodology to address the gaps, with objective to improve participants’ knowledge, skills and attitude to apply the blended approach and to sensitize actors on what needs to be advocated at the policy level. Some 661 local trainers/facilitators (ToT/ToFs), 32% of them women and 54% youth, were trained across Kenya, Tanzania, and Uganda, with additional 76 Master Trainers (MToTs) trained to backstop the ToT/ToFs. Through the implementation, the process reached 36 agribusinesses covering some 237,250 smallholder farmers trained across Kenya, Tanzania, and Uganda on CSA technologies, practices, and innovations by the end of 2020. The blended approach offers lessons to transform extension to help farmers improve food security and resilience. Preliminary findings indicate that the process is rapidly shaping individual adaptive behavior and group adaptive thinking. Lessons also show a strong need for agronomists to work more closely with agro-meteorologists to ensure that farmers are properly guided to participate appropriately in the co-generation and application of climate information and agro-weather advisories, which they can interpret easily and utilize for their agricultural production purposes. Experience from this initiative can be leveraged to develop scalable participatory extension and training models

This study investigated the efficacy of advanced oxidation process (AOP) for the reduction of pollution loads in mixed agro-food industrial wastewaters (dairy and slaughterhouse) in Nablus city, Palestine. Bench-scale Jar tests using an advanced oxidation process (AOP) were performed as a pretreatment stage. Initial results on direct applications of Fenton’s process on mixed agro-food wastewater (COD: 15400-18200 mg/l) were unsatisfactory. Hence, the performance of the Fenton process was applied on three mixed wastewater samples with different pre-treatment trials: (A) coagulant (FeCl3.6H2O) addition, (B) settling (2h), and use of flocculent (lime Ca(OH)2) in sample (C). Preceded with lime, Fenton`s process (Sample C) was most effective in the removal of organic carbon and nitrogen (89% COD; 80% TKN). The removal efficiency in inorganic loads (91% TSS; 62% TS) were achieved under H2O2/COD (w/w ratio 2:1), H2O2/Fe+2 (w/w ratio 10:1) and acidic conditions (pH = 3). The adoption of AOP technology by agro-food industries could ensure compliance with municipal by-laws and acquire connection permits to sewerage networks.

The Italian Stone Pine (Pinus pinea L.) is one of the most employed ornamental trees in towns with Mediterranean climates. For example, in the city of Rome, Pinus is the most common genus, with more than 51,000 trees. This study investigates technical and economic features of maintenance operations of Stone Pines and evaluates the productivity and costs of the observed yards. Pruning and felling are the most frequent management operations of trees in towns and this study analyzes the features of these operations carried out in 14 work sites. The operations were carried out either with aerial platforms (19 trees) or ascending the crown by tree-climbing (6 trees). The operations were sampled with time studies (12 trees for pruning and 13 for felling). Work time was measured from the beginning of operations to the transport of the residual biomass to the collection and loading point, using centesimal stopwatches and video recording. The total residual biomass was weighed or assessed. Total observation time amounted to 63.1 hours. The evaluation of the costs of each work site considered the fixed and the variable costs and the costs for the labor force. A Multiple Linear Regression model (statistics: determination coefficient R2: 0.74, adjusted R2: 0.67, p-value < 0.001) which utilizes four regressors easily evaluable before the work, was adopted to predict the gross time of the operations. This paper can contribute to optimize trees maintenance methods in urban sites and to assess the potential residual wood biomass attainable from urban forestry maintenance in the city of Rome.

This study investigated the reduction of organic loads from mixed agro-food industrial wastewaters (dairy and slaughterhouse) of Nablus city using advanced oxidation process (AOP), a high- rate chemical oxidation reaction. Bench-scale Jar tests using an advanced oxidation process (AOP) were performed as a pretreatment stage. Direct applications of classical Fenton’s process on mixed raw agro-food wastewater samples (COD: 15400-18200 mg/l) revealed unsatisfactory results. The performance of the Fenton process was evaluated using three mixed samples with different pre-treatment trials: (A) coagulant (FeCl3.6H2O) addition, (B) settling (2h) allowed, and use of flocculent (lime Ca(OH)2) in sample (C). Compared with other partial treatments, sample (C), Fenton`s process lime preceded, was the most effective in the removal of organic (89% COD; 80% TKN) and inorganic loads (91% TSS; 62% TS) under H2O2/COD (w/w ratio 2:1), H2O2/Fe+2 (w/w ratio 10:1) and acidic conditions (pH =3). Obtained results comply with Nablus municipal by-law (COD below 2000 mg/l), which help decision-makers within the agro-food industries install pollution reduction systems. Investment in the Fenton-based peroxidation process, allow agro-food industries to obtain connection permits to sewage networks.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

This study evaluates the production of biohydrogen from agro industrial waste. The worldwide energy demand is increasing exponentially and the reserves of fossil fuels are depleting, the combustion of fossil fuels has the effect on environment because of CO2 emission. Hydrogen generation market size is forecast to cross 180 billion by 2024, according to a new research report by global market. For the production of biohydrogen. we had chosen groundnut shell as our source, using Tween80 as a surfactant we had undergone pre-treatment studies for (10min,20min,30min,40min,50min) we had estimated the content of cellulose, protein, carbohydrates at (1%,2%,3%,4%,5%) and obtained the optimum value in the form of graph. The production of hydrogen is done by using the rumen fluid of the cow and the quantity of the hydrogen produced by this process is identified by using the analytical instrument Gas Chromatography.

The publication presents the assessment of the influence of surface treatment such as shot-peening on the fatigue life of a compressor blade exposed to resonant vibrations. As part of the work, a geometric model of the blade was developed and a numerical modal and fatigue analysis were performed. The fatigue analysis was based on the Manson-Coffin-Basquin and Ramberg-Osgood models. As part of the work, the influence of different values of residual stresses on the results of fatigue life was determined. Additionally, the location of the highest equivalent stresses was established. The obtained results of the numerical analyzes were compared with the results presented in the scientific literature. An additional aim of the study was to determine the size of the grains at various points of the blade as well as the thickness of the layer plasticized as a result of peening. The obtained results are presented in the form of tables and charts. The relationship between the location of the highest values of equivalent stresses and the thickness of the plasticized layer was determined. The explanation of the effect of shot peening on the increase in fatigue life of the blade was proposed.

Residual stress (RS) is the most challenging problem in metal additive manufacturing (AM) since the build-up of high tensile RS may influence the fatigue life, corrosion resistance, crack initiation, and failure of the additively manufactured components. While tensile RS is inherent in all the AM processes, fast and accurate prediction of stress state within the part is extremely valuable and would result in optimization of the process parameters in achieving a desired RS and control of the build process. This paper proposes a physics-based analytical model to rapidly and accurately predict the RS within the additively manufactured part. In this model, a transient moving point heat source (HS) is utilized to determine the temperature field. Due to the high temperature gradient within the proximity of the melt pool area, material experience high thermal stress. Thermal stress is calculated by combining three sources of stresses known as stresses due to the body forces, normal tension, and hydrostatic stress in a homogeneous semi-infinite medium. The thermal stress determines the RS state within the part. Consequently, by taking the thermal stress history as an input, both the in-plane and out of plane RS distributions are found from incremental plasticity and kinematic hardening behavior of the metal by considering volume conservation in plastic deformation in coupling with the equilibrium and compatibility conditions. In this modeling, material properties are temperature-sensitive since the steep temperature gradient varies the properties significantly. Moreover, the energy needed for the solid-state phase transition is reflected by modifying the specific heat employing the latent heat of fusion. Furthermore, the multi-layer and multi-scan aspects of metal AM are considered by including the temperature history from previous layers and scans. Results from the analytical RS model presented excellent agreement with XRD measurements employed to determine the RS in the Ti-6Al-4V specimens.

This paper examined the multifractal properties of six acknowledged agro-meteorological parameters, such as reference evapotranspiration (ET0), wind speed (U), incoming solar radiation (SR), air temperature (T), air pressure (P), and relative air humidity (RH) of five stations in California, USA. The investigation of multifractality of datasets from stations with differing terrain conditions: Dagget, Bakersfield, Santa Maria, Los Angeles and San Diego using the Multifractal Detrended Fluctuation Analysis showed the existence of a long term persistence and multifractality irrespective of the location. The scaling exponents of SR and ET0 time series are found to be higher for stations with higher altitudes. Subsequently, this study proposed using the novel multifractal cross correlation (MFCCA) method to examine the multiscale-multifractal correlations properties between ET0 and other investigated variables. MFCCA could successfully capture the scale dependent association of different variables and the dynamics in the nature of their associations from seasonal to multi-annual time scale. The multifractal exponents of pressure and relative air humidity are consistently lower than the exponents of ET0, irrespective of station location. This study found that joint scaling exponent was nearly the average of scaling exponents of individual series in different pairs of variables. Additionally, the α-values of joint multifractal spectrum were lower than the α values of both of the individual spectra, validating two universal properties in the mutifractal cross correlation studies for agro-meteorological time series. The temporal evolution of cross-correlation showed similar pattern for all pair-wise associations involving ET0, except for the RH-ET0 link.

Laser shock peening as an innovative surface treatment technology can effectively improve the fatigue life, sur-face hardness, corrosion resistance, and residual compressive stress. Compared with the laser shock peening, the warm laser shock peening (WLSP) is a new surface treatment technology to improve materials’ surface performances, which takes advantage of thermal mechanical effects on stress strengthening and micro-structure strengthening, results in more stable distribution of the residual compressive stress under heating and cyclic loading process. In this paper, the microstructure of GH4169 nickel super-alloy processed by WLSP technology with differ-ent laser parameters were investigated. The proliferation and tangling of dislocations in GH4169 were observed and the dislocation density increased after WLSP treatment. The influences of different treatment by LSP and WLSP on the microhardness distribution of the surface and along cross-sectional depth were investi-gated. The microstructure evolution of the GH4169 alloy being shocked with WLSP were studied by TEM. The effect of temperature on the stability of high temperature microstructure and properties of GH4169 alloy WLP was investigated.

Welded structures are subjected to internal residual stress after manufacturing that may affect the structural strength and normally are associated with an increase on initial geometrical imperfections. This study presents a simplified method to generate an adequate representation of residual stresses on Finite Element models for structural analysis of thin-walled structures and other applications. The results obtained shown that the methodology proposed to introduce residual stresses is simple, accurate and efficient on the modulation of post-welding stresses and their pattern, thus it may be used for simulation of the thermal process.

A robust methodology to simulate virtually the residual stresses pattern in welded steel plates is presented. The methodology is applied to the structural analysis of typical welded plates belonging to ship structures, and the effect of residual stresses on the elastoplastic behavior of plates loaded axially is analyzed in comparison to the residual stress free case, both for tension and compression and including initial imperfections. Residual stresses affect in different manner plates with different geometries; thus a parametric study is performed covering the usual range of variation of the most important plate parameters that control the strength of the plates, more precisely the slenderness and the aspect ratio. The results from finite elements analysis are compared with codes and most stablished formulations and recommendations of applicability in the prediction of load-shortening curves for hull’s bending strength evaluation, ultimate strength and ultimate strain of plate elements are made.

Long non-coding RNA (lncRNA) can regulate several aspects of gene expression, being associated with complex phenotypes in humans and livestock species. In taurine beef cattle, recent evidence points to the involvement of lncRNA in feed efficiency (FE), a proxy for increased productivity and sustainability. Here, we hypothesized specific regulatory roles of lncRNA in FE of indicine cattle. Using RNA-Seq data from liver, muscle, hypothalamus, pituitary and adrenal gland from Nellore bulls with divergent FE, we submitted new transcripts to a series of filters to confidently predict lncRNA. Then, we identified lncRNA that were differentially expressed (DE) and/or key regulators of FE. Finally, we explored lncRNA genomic location and interactions with miRNA and mRNA to infer potential function. We were able to identify 126 relevant lncRNA for FE in Bos indicus, some with high homology to previously identified lncRNA in Bos taurus and some possible specific regulators of FE in indicine cattle. Moreover, lncRNA identified here were linked to previously described mechanisms related to FE in hypothalamus-pituitary-adrenal axis and are expected to help elucidate this complex phenotype. This study contributes to expanding the catalogue of lncRNA, particularly in indicine cattle, and identifies candidates for further studies in animal selection and management.

A run-of-the-mill remote sensor arrange comprises numerous vitality compelled sensor hubs that are arbitrarily sent is the sensor field. Vitality is one of the most significant parts of planning an information dispersal convention for applications, for example, war zone checking, living space observing, and so on. We present EGDD, an Energy-effective Grid-based Data Dissemination plot for arbitrarily conveyed remote sensor systems. The proposed conspire is vitality effective for dealing with both sink and source portability. EGDD depends on a virtual framework-based foundation for information scattering from various versatile sources to different portable sinks. The virtual lattice of square size is built by the main source showing up in the sensor field dependent on the remaining vitality of the sensor hubs. Moreover, we proposed an askew sending calculation for inquiry and information sending which guarantees that just a single spread hub advances the question and information at once. In EGDD, substitute scattering hubs are chosen ahead of time during the lattice development procedure and the least limit vitality level is characterized for spread hubs. When the vitality of a dispersal hub arrives at the base edge esteem, it is supplanted by another spread hub. The reenactment results show that the proposed EGDD conspire is more vitality proficient when contrasted with other information scattering conventions.

Agricultural Production today has to deal with different challenges. It has to increment production for a continuously increasing population, reducing the environmental burdens on the natural systems. In conventional agriculture, this is possible through the increase of inputs, especially nutrients, which, however, are responsible for the biggest part of emissions. It becomes more complicated though, adopting sustainable agricultural practices, to improve the quality and the quantity of agricultural production reducing the inputs use. Plant growth regulators are described in the literature for the significant role in securing crop management of modern agriculture. Therefore, this joint field experiment has been carried out on a pear orchard (Pyrus communis L. cv. Abate Fètel) in Emilia Romagna (Italy) by Fondazione Navarra and TIMAC AGRO Italia S.p.A., to test the “less for more” theory which consists in getting more and better agricultural produce using fewer inputs. Preliminary results of two consecutive years have confirmed our assumption as it was possible to substantially reduce the total fertilisation units applied, improving significantly quantitative and qualitative production indicators (i.e. flower and fruit density, fruit set (%), the average weight of fruits (g) and the total yield (t/ha)). Results have also shown a positive correlation between plant growth regulators and agronomic efficiency of pears.

In this study, fibers were extracted from different parts of the okra plant (Abelmoschus esculentus) via water- and dew-retting methods. The fibers were subjected to physical and thermal analyses. The fibers obtained from the upper part of the okra plant show higher breaking strength and lower linear density. Fibers obtained via water-retting exhibited higher breaking strength, elongation at break rates, and lower linear density values. The paper also presents the results of thermogravimetric analysis of the okra fibers. Tests were carried out in oxygen and inert gas atmospheres. The temperature range of the main thermal decomposition stage was in the 275–400°C for range thermo-oxidation and 300–425°C for pyrolysis investigation. Slight differences were found in the thermal resistances of the tested fibers, which was confirmed by an analysis using the alpha s- alpha r methodology. The calculated activation energy values show a large-spread range.

Safety assessment of structures can be obtained employing limit design to overcome uncertainties concerning actual response due to inelastic constitutive behavior and more generally to non-linear structural response and loads’ random variability. The limit analysis is used for evaluating the safety of the structures directly starting from load level without any knowledge of the load history. In the paper, the lower bound calculation is proposed where a new strain-based approach is used that allowed describing the residual stress and displacement in terms of permanent strain. The strategy used the permanent strain as the effective parameters of the procedure so that it was possible to assess the ductility requirements for the complete load program developed till collapse or shakedown. The procedure is compared to experimental results obtained on aluminum beams in shakedown.

Herein, we reported a case of complete excision of the jejunum for the treatment of esophageal cancer. A 62-year-old male was admitted with complaints of “difficulty in eating for one month and chest pain for 10 days". For complete gastrectomy and colonic polyposis, we chose the jejunum. We completely excised the jejunum and its vessels, anastomosed to the esophageal tumor resection, with no significant complications. This case showed that complete excision of the jejunum with bowel and vessels is an alternative surgical method for the treatment of esophageal cancer with free bowel shortage and no torsion of blood vessels.

Industries that rely on additive manufacturing of metallic elements, especially biomedical companies, require material science-based knowledge of how process parameters and methods affect element properties, but such phenomena are incompletely understood. In this study, we investigated the influence of selective laser melting (SLM) process parameters and additional heat treatment on mechanical properties. The research included structural analysis of residual stress, microstructure, and scleronomic hardness in low-depth measurements. Tensile tests with element deformation analysis using digital image correlation (DIC) were performed as well. Experiment results showed it was possible to observe the porosity growth mechanism and its influence on material strength. Elements manufactured with 20% lower energy density had almost half the elongation, which was directly connected with porosity growth during energy density reduction. Hot isostatic pressing (HIP) treatment allowed for a significant reduction of porosity and helped achieve properties similar to elements manufactured using different levels of energy density.

Market-orientation is widely applied to understand the expected interaction of smallholder farmers with input and output markets. Commonly used interchangeably with market participation, it is fast becoming a key milestone for attaining smallholder commercialization. This study introduces the term into the disaster resilience, seed systems and livelihoods context. Using a mixed methods approach, 120 smallholder farmers in a drought-affected district of South Africa were sampled, and information collected for analysis. The result shows that most of the farmers rely on purchased seeds and fertilizers for crop production, and on average sold 62% of their farm produce. A market orientation index (MOI) of 55% was estimated, showing that the farmers were market oriented. The farm size, quantities of seeds and fertilizer purchased, value of crop produced, amount received from crop sales, distance to markets and access to credit were found significant in determining their market orientation. Policy interventions were made to improve access to irrigation, seed varieties and extension delivery in the area. The finding has implications for development efforts at rebuilding after a natural disaster, as well as sourcing food aid from local smallholder farmers by humanitarian actors.

Prestrained at 5% and 15% duplex stainless steel UNS S32750 specimens have been subjected to electropulsing treatments with current density of 100 A/mm2 and 200 A/mm2 and 100 and 500 pulses for each current density value. Corrosion tests, X-ray diffraction, microhardness and residual stresses were collected before and after the electropulsing treatments. Tensile tests were performed after the electropulsing treatments in order to compare the mechanical response to the reference tensile tests performed before the pulsing treatments. Increase in fracture strain was observed after the pulsing treatment in comparison to the reference tensile tests. A decrease in microhardness was also observed after the electropulsing treatments for both degrees of prestrain. Electropulsing treatment almost eliminates the work-hardened state in the 5% prestrained specimens while partially recovered the 15% prestrained material increasing both uniform and fracture strain. The bulk temperature of the samples remained the same for all the duration of the treatments. The effect are to be addressed to a combined effect of the increase in atomic flux due to the electrical current and local joule heating in correspondence of crystal defects. Electropulsing treatment applied to metallic alloys is a promising technique to reduce the work hardening state without the need of annealing treatments in a dedicated furnace.

In the last few decades, a lot has been written on the use of sustainable agriculture to improve ecosystem services for resilience to climate change. However, no tangible and systematic evidence exists on how this would participate in alleviating impacts on vulnerable rural communities. This paper provides a narrative systematic review (SR) integrated with a bibliometric analysis and a concept network analysis to understand how, in a changing climate, sustainable agriculture builds the resilience of agro-systems. The search was set from the date of the first relevant article until the end of 2018. Results generated have demonstrated that: a. Only single practices and methods have been studied to assess impacts on single ecosystem services. b. Soil quality and health are considered a key indicator of sustainable agriculture. c. Albeit the assessed practices and methods have shown to improve the biodiversity of agro-systems, which makes them more resilient to extreme climate events, we are still far from reaching interdisciplinary and multi-dimensional agriculture which integrates all management aspects and generates a full range of ecosystem services. In conclusion, the study addressed the following recommendations for the scientific community and for decision-makers to orient future research strategies and efforts: a. Integration of all agro-systems services into sustainable management using an ecosystem-based approach on a life-cycle basis using Life Cycle Assessment (LCA) method; b. Improving the scientific understanding of traditional knowledge for higher synergies and for further integration; c. Unification of assessment methods and indicators for the quantification of impacts; d. Creation of a platform to share, monitor, screen, and approve assessments and evaluations of sustainable agriculture by region.

Since the 1950s sugarcane production has grown rapidly from less than 0.5 billion tonnes in the late 50s to reach over 1.9 billion tonnes in 2012 on about 27 million hectares of agricultural land. This expansion has been boosted by the high demand for bioethanol promoted as a sustainable bioenergy source which accounted in 2010 for the biggest share of the global biofuel market. Despite its benefits, the scientific debate on sugar is growing especially that counterarguments are so many, including negative impacts on different interacting ecosystems and human well-being, e.g. bigger stress on land and water resources, environmental externalities on air, a harmful impact on the biodiversity and endemic species, negative environmental externalities, health, and socio-economic aspects. This paper provides a narrative systematic review (SR) of the impacts of sugarcane production on these different ecosystems employing the ecosystem services framework for its acceptance by policy-makers. The references included for the SR were 163 and results showed that the majority of the studies are from Brazil, Australia, South Africa and the USA (≈ 75% of the literature), most of them were from peer-reviewed journals (85%), and most of the case studies adopted a quantitative research approach (93%). The literature assessed showed that sugarcane, like all agro-systems, depends on the practices and techniques to transform negative impacts into positive externalities on ecosystems and human well-being. However, the literature studied failed to include the inter-linkage in sugarcane production impacts’ and therefore to evaluate the related ecosystem services with respect to the Millennium Ecosystem Assessment (MA) framework to account for existing trade-offs. Therefore, the findings are addressed to the scientific community and decision-maker for an intensification of interdisciplinary and integrated research based on the MA framework to cover all ecosystem services, for sustainable development of the sugarcane sector.

Rapid and accurate prediction of residual stress in metal additive manufacturing processes is of great importance to guarantee the quality of the fabricated part to be used in a mission-critical application in the aerospace and automotive industries. Experimentation and numerical modeling are valuable tools for measuring and predicting the residual stress; however, to-date conducting experimentation and numerical modeling is expensive and time-consuming. Thus, herein, a physics-based thermomechanical analytical model is proposed to predict the residual stress of the additively manufactured part rapidly and accurately. A moving point heat source approach is used to predict the temperature field by considering the effects of scan strategies, heat loss, and energy needed for solid-state phase transformation. Due to the high temperature gradient in this process, part experiences a high amount of thermal stress following solidification which may exceed the yield strength of the material. The thermal stress is obtained using Green’s function of stresses due to the point body load. The Johnson-Cook flow stress model is used to predict the yield surface of the part under repeated heating and cooling. As a result of the cyclic heating and cooling and the fact that the material is yielded, the residual stress build-up is predicted based on incremental plasticity and kinematic hardening behavior of the metal according to the property of volume invariance in plastic deformation in coupling with the equilibrium and compatibility conditions. The computational methodology is realized with the laser powder fusion of maraging steel 350 as a material of example. The validation of the predictive models has been presented in terms of the comparison of predicted and measured scan-direction and build-direction residual stress distributions along depth of build under various process parameter combinations. Moreover, for the first time, the Jonson-Cook parameters of maraging steel 350 are predicted using analytical modeling of machining forces and non-linear optimization techniques.

Corrosion is considered as one of the main factors in the structural performance deterioration of steel members. In this study, experimental and numerical methods were used to assess the reduction in compressive strength of short tubular steel columns with local corrosion damage. The corrosion damage was varied with different depths (0, 1.5, 2, 3, 4, 4.5, and 6 mm), height (0, 20, 40, 60, 80, 100, 120, 140, 160, and 180 mm), circumference (0, 90, 180, 270, and 360°), and location along the column. A parametric numerical study was performed to establish a correlation between the residual compressive strength and the severity of corrosion damage. The results showed that as the corrosion depth, height and circumference increased, the compressive strength decreased linearly. As for the corrosion height, the residual compressive strength became constant after decreasing linearly when the corrosion height was greater than the half-wavelength of buckling of the short columns. An equation is presented to evaluate the residual compressive strength of short columns with local corrosion wherein the volume of the corrosion damage was used as a reduction factor in calculating the compressive strength. The percentage error using the presented equation was found to be within 11.4%.

The sensor nodes have limited computation, sensing, communication capabilities and generally operated by batteries in a harsh atmosphere with non-replenish able power sources. These limitations force the sensor network subject to failure because most of the energy is spent on sensing, computing and data transmission. This paper introduces an Energy Efficient Clustering and Shortest-Path Routing Protocol (EECSRP) to assist Wireless Sensor Networks (WSNs) by (a) extending the lifespan of the network (b) effectively using the battery power (c) decreasing the network overhead and (d) ensuring a high packet transmission ratio with minimal delay. The delay time-based Cluster Head (CH) is elected based on the node degree, residual energy and Received Signal Strength (RSS) to accomplish the goal. Additionally, the RSS-based network partitioning is implemented to evaluate the gradient based on demand routing between source (sensing node) and destination (BS). Whenever the current CH residual energy goes under the threshold level, the proposed protocol performs the clustering process, reducing the exchange of control packets. However, the BS periodically gathers the data from every single CH which helps to reduce the collision and Medium Access Control (MAC) layer conflict. From the simulation results, it is the evident that the proposed protocol performance in terms of average end-to-end latency, packet delivery ratio, average energy consumption and control overhead is better than the well-known current protocols.

Fiber-cement composites were prepared from cellulosic cotton residue (CCR) arise from sanding process (emerizing). The effect of different concentrations: 0.5% and 1%, and granulometry: thick (retained in a14 mesh sieve) and thin (retained in a 48 mesh sieve) of this residue were evaluated on tensile strength of cement slurries with seven (07) curing days. To characterize the CCR, TGA, FT-IR, SEM and XRD analysis were performed and the residue resistance in an alkaline environment was also evaluated. Splitting tensile strength test, known as Brazilian Test, was used to assess effects of the fibers on the mechanical behavior of cement matrix. Analyzing the results, the CCR proved to be resistant in an alkaline environment, meaning that it can withstand the alkaline environment of cement matrix. The results showed an improvement superior to 17% in tensile strength for 1% of CCR. Therefore, the CCR presents a great application potential in cement pastes used for oil well cementing that requires to increase its tensile strength, once a significant improvement was achieved with a low-residue employee.

Alzheimer's is a disease for which there is no cure. Diagnosing Alzheimer's Disease (AD) early facilitates family planning and cost control. The purpose of this study is to predict the presence of AD using socio-demographic, clinical, and Magnetic Resonance Imaging (MRI) data. Early detection of AD enables family planning and may reduce costs by delaying long-term care. Accurate, non-imagery methods also reduce patient costs. The Open Access Series of Imaging Studies (OASIS-1) cross-sectional MRI data were analyzed. A gradient boosted machine (GBM) predicted the presence of AD as a function of gender, age, education, socioeconomic status (SES), and Mini-Mental State Exam (MMSE). A Residual Network with 50 layers (ResNet-50) predicted CDR presence and severity from MRI's (multi-class classification). The GBM achieved a mean 91.3% prediction accuracy (10-fold stratified cross validation) for dichotomous CDR using socio-demographic and MMSE variables. MMSE was the most important feature. ResNet-50 using image generation techniques based on an 80% training set resulted in 98.99% three class prediction accuracy on 4,139 images (20% validation set) at Epoch 133 and nearly perfect multi-class predication accuracy on the training set (99.34%). Machine Learning methods classify AD with high accuracy. GBM models may help provide initial detection based on non-imagery analysis, while ResNet-50 network models might help identify AD patients automatically prior to provider review.

In this study, we introduce a novel framework for the estimation of residual renal function (RRF), based on the population compartmental kinetic behavior of Beta 2 Microglobulin (B2M) and its dialytic removal. Using this model, we simulated a large cohort of patients with various levels of RRF receiving either conventional high-flux hemodialysis or on-line hemodiafiltration. These simulations were used to estimate a novel population kinetic (PK) equation for RRF (PK-RRF) that was validated in an external public dataset of real patients. We assessed the performance of the resulting equation(s) against their ability to estimate urea clearance using cross-validation. Our equations derived entirely from computer simulations and advanced statistical modeling, and had extremely high discrimination (AUC 0.808 – 0.909) when applied to a human dataset of measurements of RRF. A clearance-based equation that utilized pre and post dialysis B2M measurements, patient weight, treatment duration and ultrafiltration had higher discrimination than an equation previously derived in humans. Furthermore, the derived equations appeared to have higher clinical usefulness as assessed by Decision Curve Analysis, potentially supporting decisions that for individualizing dialysis frequency in patients with preserved RRF.

In laser-assisted milling, higher temperature in shear zone softens the material potentially resulting in a shift of mean residual stress, which significantly affects the damage tolerance and fatigue performance of product. In order to guide the selection of laser and cutting parameters based on the preferred mean residual stress, inverse analysis is conducted by predicting residual stress based on guessed process parameters, which is defined as the forward problem, and applying iterative gradient search to find process parameters for next iteration, which is defined as the inverse problem. An analytical inverse analysis is therefore proposed for the mean residual stress in laser-assisted milling. The forward problem is solved by analytical prediction of mean residual stress after laser-assisted milling. The residual stress profile is predicted through the calculation of thermal stress, by treating laser beam as heat source, and plastic stress by first assuming pure elastic stress in loading process, then obtaining true stress with kinematic hardening followed by the stress relaxation. The variance-based recursive method is applied to solve inverse problem by updating process parameters to match the measured mean residual stress. Three cutting parameters including depth of cut, feed per tooth, and cutting speed, and two laser parameters including laser-tool distance and laser power, are updated with respected to the minimization of resulting residual stress and measurement in each iteration. Experimental measurements are referred on the laser-assisted milling of Ti-6Al-4V grade 5 and ELI. The percentage difference between experiments and predictions is less than 5% for both materials, and the selection is completed within 50 loops.

Analysis of Fatigue Strain, Fatigue Modulus and Fatigue Damage for the modeling of concrete plays a vital role in the evolution material behaviour which is heterogeneous and anisotropic in nature. In this paper, the Level-S nonlinear fatigue strain curve, fatigue modulus curve, residual strain curve of concrete in compression, tension, flexure and torsional fatigue loading were proposed using strain life approach. The parameters such as physical meaning, the ranges, and the impact on the shape of the curve were discussed. Then, the evolution model of fatigue modulus was established based on the fatigue strain evolution model, fatigue modulus evaluation model, residual strain evaluation model, secondary strain evaluation model. The hypothesis of fatigue modulus is inversely related with the fatigue strain amplitude. The fatigue evolution of concrete damages the bond between material grains, changed the orientation of structure of molecules and affects the elastic properties resulting in the reduction of material stiffness and modulus by utilizing strain life analysis, regarding stiffness degradation and inelastic deformation by formation of microcracking, macro cracking, cracking which is heterogeneous and anisotropic in nature . This paper presents the Fatigue Strain Life Model and analyses of fatigue strain, fatigue modulus and damage parameters of concrete which is capable of predicting stiffness degradation, inelastic deformation, strength reduction under fatigue loading. Hence, the obtainable results were compared with experimental results for the validation of the proposed model.

A Wireless Body Area Sensor Network (WBASN) is combination of numerous sense nodes, positioned onto/close or inside a person body. Wireless Body Area Sensor Networks (WBASN) is a developing automation trend that exploits wireless sensor nodes to put instantaneous wearable well-being of ill person to improve individual’s existence. The sensor nodes might be used outwardly to observe abundant health parameters (like heart activity, blood pressure and cholesterol) of an ill person at a vital site within hospital. Hence the goal of WBASN is much crucial, enhancing the lifetime of nodes is compulsory to sustain many issues such as utility and efficiency. It is essential to evaluate time that when the first node will die it we want to refresh or change the battery reason is that loss of crucial information is not tolerable. The lifetime is termed as the time interval when a first node dies out due to battery exhaustion. In our proposed protocol life time of a network is the main concern as well other protocol related issues such as throughput, path loss, and residual energy. Bio-sensors are used for deployment on human body. Poisson distribution and equilibrium model techniques have been used for attaining the required results. Multi-hop network topology and random network node deployment used to achieve minimum energy consumption and longer network lifetime.

Three hundred ten 12-wek-old laying quails (155 each) were randomly selected from the initial population and kept in individual battery cages. The measurements of growth and egg production were determined to derive RFI. The relationship between RFI and egg quality, blood parameters and carcass characteristics was also determined. The results indicated that the gray quails had significantly higher egg mass and lower broken eggs compared to the white quails. A significant increase for eggshell strength and shell % was found in eggs produced from gray quails compared to white counterparts, although the shell thickness was the same. The results of multiple regression analysis clearly identified a significant effect of metabolic body weight and egg mass in computing expected feed intake rather than body weight gain in both varieties of Japanese quails. Strongly positive correlation between RFI and feed intake in both gray and white quail varieties was found. The same trend was also observed for feed conversion ratio (FCR). Therefore, including RFI in selection criteria of Japanese quail to improve FCR under high environmental temperature is highly recommended.

Durum wheat is an important food crop in the world and an endemic species of sub-Saharan Africa (SSA). In the highlands of Ethiopia and the oases of the South Sahara this crop has been cultivated for thousands of years. Today, smallholder farmers still cultivate it on marginal lands to assure production for their self-consumption. However, durum wheat is no longer just a staple crop for food security but it has become a major cash crop. In fact, the pasta and couscous industry currently purchase durum grain at prices 10 to 20% higher than bread wheat. Africa as a whole imports over € 4 billion per year of durum grain to provide the raw material for its food industry. Hence, African farmers could obtain a substantial share of this large market by turning their production to this crop. Here, the achievements of the durum breeding program of Ethiopia are revised to reveal a steep acceleration in variety release and adoption in the last decade. Furthermore, the variety release for Mauritania and Senegal is described to show how modern breeding methods could be used to deliver grain yields above 3 t ha^-1 in seasons of just 92 days of length and daytime temperatures always above 32°C. This review describes the ability of releasing durum wheat varieties adapted to all growing conditions of SSA, from the oases of the Sahara to the highlands of Ethiopia. This potential area of expansion for durum wheat production in SSA is not linked to any breeding technology, but rather it remains dependent on the market ability to purchase these grains at a higher price to stimulate farmer adoption. The critical importance of connecting all actors along the semolina value chain is presented in the example of Oromia, Ethiopia, and that success story is then used to prompt a wider discussion on the potential of durum wheat as a crop for poverty reduction in Africa.

Background: The presence of HIV residual replication markers was investigated among distinct subgroups of individuals on antiretroviral treatment (ART). Methods: One hundred sixteen patients were distributed into 5 treatment groups: first-line suppressive ART with a non-nucleoside analog reverse-transcriptase inhibitor (NNRTI) (n = 26), first-line suppressive ART with boosted protease inhibitors (PI-r) (n = 25), suppressive salvage therapy using PI-r (n = 27), suppressive salvage therapy with PI-r and raltegravir (n = 22) and virologic failure (n = 16). Episomal and total DNA quantitation was evaluated. HIV antibody and LPS quantitation was performed. Results: Episomal DNA was positive in 26% to 38% of individuals under suppressive ART, and it was higher among ART virologic failure group (p = 0.04). HIV proviral load was higher among patients with detectable episomal DNA (p = 0.01). Individuals receiving initial PI-r treatment presented lower HIV antibody (p = 0.027) and LPS (p = 0.029) levels than individuals receiving NNRTI. There was a negative correlation between episomal DNA quantitation and the duration of suppressive ART (p = 0.04), CD4+ T-cell count (p = 0.08), and CD8+ T-cell count (p = 0.07). Conclusions: Residual HIV replication has been inferred among individuals under suppressive ART according to episomal DNA detection. Residual replication may decrease with longer periods of suppressive ART and higher levels of CD4+ and CD8+ T cells. The relationship between episomal DNA and total DNA suggests there is a replenishment of the proviral reservoir. Lower antibody and LPS levels among patients with initial PI-r ART suggest these regimens may more effectively suppress HIV, more effectively decreasing HIV antigenic component.

For water-stressed regions like Iran improving the effectiveness and productivity of agricultural water-use is of utmost importance due to climate change and unsustainable demands. Therefore, a hydro-economic model has been developed here for the Zarrine River Basin with the central concept of that demands are value-sensitive functions, where quantities of water-uses at different locations and times have a changeable economic benefits. To do this, the potential crop yields and the surface and groundwater resources, especially Boukan Dam inflow are simulated using the hydrologic model, SWAT, based on predicted climatic scenarios i.e. quantile mapping-downscaled projections. Then, to allocate the agricultural water based on the agro- economic crop water productivity (AEWP) of crops, a basin-wide water management tool, MODSIM, is customized. Next, a simulation- optimization model has been developed using a coupled CSPSO-MODSIM, to optimize the total AEWP, considering climatic impact and crop pattern scenarios, for 2020-2038, 2050-2068 and 2080-2098 periods. Finally, the optimum crop pattern and crop water irrigation depths are presented for different RCPs and periods. The results indicated that this approach will improve considerably the AEWPs and decrease the agricultural water-use up to 40%. Thus, this integrated model is able to support water authorities and other stakeholder in a water-scarce basin, as is the study area.

Compressive residual stresses in thin films can inhibit crack propagation under normal or sliding contact loading, with associated enhancement of the coating apparent toughness, load bearing capacity and wear resistance. This study investigates the influence of residual stress distributions on the thin film/substrate adhesion using a nanoindenter coupled with scanning electron microscope (SEM) investigations of indentation induced failure modes. Reactive and un-reactive magnetron sputtering with ion plating was used to coat a (100) silicon substrate with aluminum nitride (AlN) with and without an aluminum (Al) adhesion layer. The presence of an Al bond layer gives additional interfacial tensile stress because of the difference in thermal expansion coefficient. Additionally, a different magnitude of residual stresses in the AlN coating was achieved by changing the applied bias voltage onto the substrate. Wafer curvature method and incremental focused ion beam (FIB) milling, combined with high-resolution in situ scanning electron microscopy (SEM) imaging and full field strain analysis by digital image correlation (DIC), were used to measure the average and in-depth stress residual stress distribution in the produced coatings. The adhesion energy was then quantified by using a nanoindentation based model. Results demonstrate that the additional tensile residual stress in the aluminum adhesion layer decrease significantly the coating adhesion, even in presence of a higher compressive stress state in the AlN top-layer. Therefore, the coatings without Al-layer showed better adhesion because of a more homogeneous compressive residual stress in comparison with the coating having Al layer, even though both groups of coatings are produced under same bias voltage. Results are discussed, and some general suggestions are made on the correlation between coating/substrate property combination and the adhesion energy of multilayer stacks. The results suggested that Al bond-layer and inhomogeneous residual stresses affected the adhesion of AlN negatively to a substrate like silicon.

Consumption of coffee by women early in their pregnancy has been viewed as potentially increasing the risk of miscarriage, low birth weight, and childhood leukemias. Many of these reports of epidemiologic studies have not acknowledged the potential biases inherent in studying the relationship between early-pregnancy-coffee consumption and subsequent events. I discuss five of these biases, recall bias, misclassification, residual confounding, reverse causation, and publication bias. Each might account for claims that attribute adversities to early-pregnancy-coffee consumption. To what extent these biases can be avoided remains to be determined. At a minimum, they need to be acknowledged wherever they might account for what is reported.

The residual multiparticle entropy (RMPE) of a fluid is defined as the difference, Δs, between the excess entropy per particle (relative to an ideal gas with the same temperature and density), s_ex, and the pair-correlation contribution, s₂. Thus, the RMPE represents the net contribution to s_ex due to spatial correlations involving three, four, or more particles. A heuristic “ordering” criterion identifies the vanishing of the RMPE as an underlying signature of an impending structural or thermodynamic transition of the system from a less ordered to a more spatially organized condition (freezing is a typical example). Regardless of this, the knowledge of the RMPE is important to assess the impact of non-pair multiparticle correlations on the entropy of the fluid. Recently, an accurate and simple proposal for the thermodynamic and structural properties of a hard-sphere fluid in fractional dimension 1 < d < 3 has been proposed [Santos, A.; López de Haro, M. Phys. Rev. E 2016, 93, 062126]. The aim of this work is to use this approach to evaluate the RMPE as a function of both d and the packing fraction ϕ. It is observed that, for any given dimensionality d, the RMPE takes negative values for small densities, reaches a negative minimum Δs_min at a packing fraction ϕ_min, and then rapidly increases, becoming positive beyond a certain packing fraction ϕ₀. Interestingly, while both ϕ_min and ϕ₀ monotonically decrease as dimensionality increases, the value of Δs_min exhibits a nonmonotonic behavior, reaching an absolute minimum at a fractional dimensionality d ≃ 2.38. A plot of the scaled RMPE Δs/|Δs_min| shows a quasiuniversal behavior in the region −0.14 ≲ ϕ − ϕ₀ ≲ 0.02.

Orbit and clock products are used in real-time GNSS precise point positioning without knowing their quality. This study develops a new approach to detect orbit and clock errors through comparing geometry-free and geometry-based wide-lane ambiguities in PPP model. The reparameterization and estimation procedures of the geometry-free and geometry-based ambiguities are described in detail. The effects of orbit and clock errors on ambiguities are given in analytical expressions. The numerical similarity and differences of geometry-free and geometry-based wide-lane ambiguities are analyzed using different orbit and clock products. Furthermore, two types of typical errors in orbit and clock are simulated and their effects on wide-lane ambiguities are numerically produced and analyzed. The contribution discloses that the geometry-free and geometry-based wide-lane ambiguities are equivalent in terms of their formal errors. Although they are very close in terms of their estimates when the used orbit and clock for geometry-based ambiguities are precise enough, they are not the same, in particular, in the case that the used orbit and clock, as a combination, contain significant errors. It is discovered that the discrepancies of geometry-free and geometry-based wide-lane ambiguities are coincided with the actual time-variant errors in the used orbit and clock at the line-of-sight direction. This provides a quality index for real-time users to detect the errors in real-time orbit and clock products, which potentially improves the accuracy of positioning.

Agriculture is the backbone of Kenya’s economy, supporting up to 80% of the rural livelihoods. Kenya’s export horticulture is currently the leading Agriculture subsector in Kenya has evolved from small-holder farming to agro-industrial large-scale export farming dominated by multinational companies. It is regarded as an agro-industrial food system based on the economies of scale producing for mass markets outside of the production area. Much of the food consumed from this food system has undergone multiple transformations and been subject to a host of formal and informal insitutions (rules, regulations, standards, norms and values). An Anthropological study of export horticulture in Northwest Mount Kenya was carried out utilizing qualitative data collection methods in Northwest Mount Kenya region. Data was coded and analysed thematically based on grounded theory approach. The study described the institutional settings of export horticulture from an emic perspective as changing and defining the operations of the food system access and management of common pool resources, namely water and land. With the agro-industrial food system competing for these scarce resources in a semi-arid zone, there is potential for conflict and also reduced production and overall benefits to the different actors in the study area.

Abstract: The study focuses on how socio-economic and demographic indicators affect fertilization sustainability (excessive amount of fertilization). Principally we aim to examine the significance magnitude of the effects of three socio-demographic variables such as traditional way of fertilization, rental land farming, and farmers’ younger age on over-fertilization in Bangladesh and other developing countries. In 1960s, Bangladesh state authority launched a campaign ‘Grow more Food’ to feed huge numbers of population and thus the farmers are provided chemical fertilizers and pesticides at a subsidized low price. Farmers began to use huge amount of fertilizers for gaining high yields and continued it to present causing environmental woes a lot. We interview (face-to-face, focus group discussion, and phone interview) 210 Bangladesh farmers in 2016 by semi-structured questionnaire. Data has been analyzed using General Linear Model (GLM) in Univariate Analysis of Variance. The study found the effect of traditional way of fertilization on excessive amount of fertilization is strongly significant at 1% level. Apart from, rental land farming and farmers’ younger age have a significant influence on over- fertilization; though their significance level (5% and 10% respectively) is quasi-strong. Policy makers can be able to formulate fertilizer policy on the basis of these findings.

An on-site, ultra-sensitive, and quantitative sensing method was developed based on quantum dot nanobeads (QDNBs) and test strip for the determination of total aflatoxins (AFTs) in rice and peanut. The monoclonal antibody against AFT (mAbAFT) was home-made and labeled with QDNB. After the pre-coating of the AFT antigen on the test line (T line), the competitive immunoreactions were conducted between AFT and AFT antigen on the T line with QDNBs-mAbAFT. Under optimal conditions, this approach allowed a rapid response towards AFT with a considerable sensitivity of 1.4 pg/mL and 2.9 pg/mL in rice and peanut matrices, respectively. The put-in and put-out duration were within 10 min. The recoveries for AFT in rice and peanut samples matrices were recorded from 86.25–118.0% with the relative deviations (RSD) below 12%. The assay was further validated via the comparison between this QDNB strip and the conventional HPLC method using spiked samples. Thus, the design provided a potential alternative for on-site, ultra-sensitive, and quantitative sensing of AFT that could also be expanded to other chemical contaminants for food safety.

The scratch test consists in pushing a tool across the surface of a material at a given penetration depth or applied load. It has several applications in Science and Engineering including strength testing, damage and quality control of thin films and coatings. Despite numerous attempts in scientific literature, the application of scratch test to characterizations of fracture properties remains a heavily controversial topic. Therefore, this investigation arises as an experimental study in order to assess the fracture toughness using scratch test. A study on the effect of cryogenic treatment, performed after tempering, on fracture toughness, via scratch test experiments, of different tool steels has been made. A laboratory investigation on AISI D2, AISI M2 and X105CrCoMo18 steel confirms the possibility of increasing the fracture toughness by carrying out the cryogenic treatment after the usual heat treatment

In the past few years, micromodels have become a useful tool for visualizing flow phenomena in porous media with pore structures, e.g., the multifluid dynamics in soils or rocks with fractures in natural geomaterials. Micromodels fabricated using glass or silicon substrates incur high material cost; in particular, the microfabrication-facility cost for making a glass or silicon-based micromold is usually high. This may be an obstacle for researchers investigating the two-phase-flow behavior of porous media. A rigid thermoplastic material is a preferable polymer material for microfluidic models because of its high resistance to infiltration and deformation. In this study, cyclic olefin copolymer (COC) was selected as the substrate for the micromodel because of its excellent chemical, optical, and mechanical properties. A delicate micromodel with a complex pore geometry that represents a two-dimensional (2D) cross-section profile of a fractured rock in a natural oil or groundwater reservoir was developed for two-phase-flow experiments. Using an optical visualization system, we visualized the flow behavior in the micromodel during the processes of imbibition and drainage. The results show that the flow resistance in the main channel (fracture) with a large radius was higher than that in the surrounding area with small pore channels when the injection or extraction rates were low. When we increased the flow rates, the extraction efficiency of the water and oil in the mainstream channel (fracture) did not increase monotonically because of the complex two-phase-flow dynamics. These findings provide a new mechanism of residual trapping in porous media.

Camelina (Camelina sativa L.) is an oilseed with potential for use as a raw material in second-generation biofuels. Camelina has a seed yield of up to 2380 kg ha^-1 and contains around 45% fatty acids. Selection of a suitable site is critical for production optimization. The objective of this study was to determine Chilean agro-climatic suitability for establishing camelina as a productive alternative. Climate and soil requirements and geographical restraints were evaluated for the species, considering the climatological characteristics of its regions of origin, as well as regions where camelina is successfully grown in the rest of the world. The variables considered include factors (maximum temperatures of the warmest month, water deficits, and degree days) and limitations (altitude, geomorphology, and current land use), which permitted the evaluation of the national territory for a certain level of suitability. It was determined that 1.3% of the national territory (960,664 ha) has some degree of suitability for camelina adoption. Between the Biobío and Los Lagos regions, 49.0% of land (471,203 ha) is in the category of without thermic restrictions, with mild water restrictions, and mild soil restrictions or without information, which can be used for camelina production. The Los Ríos region had 21.4% surface area (321,176 ha) with some level of suitability for camelina, the most suitable region to establish this crop in Chile.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

In the current paper, a residual generation filter with finite memory structure is proposed for sensor fault detection. The proposed finite memory residual generation filter provides the residual by real-time filtering of fault vector using only the most recent finite observations and inputs on the window. It is shown that the residual given by the proposed residual generation filter provides the exact fault for noise-free systems. The proposed residual generation filter is specified to the digital filter structure for the amenability to hardware implementation. Finally, to illustrate the capability of the proposed residual generation filter, numerical examples are performed for the discretized DC motor system having the multiple sensor faults.

Recently, many authors have been interested to introduce fuzzy implications over t-norms and t-conorms. In this paper, we introduce (S,N) and residuum fuzzy implication for Dubois t-norm and Hamacher's t-norm. Also, new concepts so-called (T,N) and residual fuzzy co-implication in dual Heyting Algebra are investigated. Some examples as well as application are discussed as well.