The wind industry is looking for ways to accurately predict the reliability and availability of newly installed wind turbines. Failure modes, effects and criticality analysis (FMECA) is a technique utilized for determining the critical subsystems of wind turbines. There are several studies which applied FMECA for wind turbines in the literature, but no studies so far have considered different weather conditions or climatic regions. Furthermore, various design types of wind turbines have been analyzed applying FMECA but no study so far has applied FMECA to compare the reliability of geared and direct-drive wind turbines. We propose to fill these gaps by using Koppen-Geiger climatic regions and two different turbine models of direct-drive and geared-drive concepts. A case study is applied on German wind farms utilizing the WMEP database which contains wind turbine failure data from 1989 to 2008. This proposed methodology increases the accuracy of reliability and availability predictions and compares different wind turbine design types and eliminates underestimation of impacts of different weather conditions.

Installation of offshore wind farms is rising, driven by the goal of changing the global energy matrix. However, many of its possible impacts are still unknown. Increased noise levels, disruptions to food chains, pollution due to traffic, and impacts on fishing communities and tourism are all potential effects to consider. Marine habitats are essential carbon dioxide sinks. Therefore, losing marine biodiversity due to offshore wind farms can be counterproductive in mitigating climate change. Balancing biodiversity conservation, wind potential, and political interests is challenging. Today, Uruguay has practically decarbonized its electrical matrix, incorporating wind, solar, and biomass energy alongside hydroelectricity. In line with this, the country's Hydrogen Roadmap highlights green hydrogen as relevant, potentially serving as a transportation fuel for both domestic consumption and export. Combining the country's strong base of wind experience with its sustainable policy, it plans to implement offshore wind farms to produce green hydrogen, making studies of its impacts crucial. This paper reviews the current social and environmental information on the Uruguayan coastal habitat, analyzes onshore wind farms' ecological studies, and examines offshore wind farms' global environmental and social impacts. Finally, it proposes suggested studies for environmental approval for offshore wind farms.

In recent years, excessive heat in the urban texture has become the main problem in the humid and calm wind city of Babolsar with high density, especially in high-rise areas. Therefore, in order to create comfort in this region, it is necessary to establish and continue the wind circulation in space with an environmentally compatible and optimal configuration. The study applies combination of literature, field measurement, experimental validation of CFD simulation output, and comparative analysis. After field measurement and validation of FLOW-3D simulation software (V11.2.2), the relationship between these parameters (height, the width of passages, enclosure between buildings, and buildings' orientation) will be studied which affects the wind’s velocity and direction. The factors of the buildings' orientation and enclosure based on the passages' width have opposite reactions in the direction of the prevailing wind especially from perpendicular side. In this study, two effective factors are on wind velocity: 1- The orientation of the buildings towards the wind flow by creating permeability 2- Reducing the enclosure by increasing the width of the passage's perpendicular to the wind flow (w '= 3w, E' = 0.33E). According to the theoretical and practical study, first, the creation of permeability in the body of the block and the separation of buildings instead of aggregation has been studied, and then reducing the confinement of streets perpendicular to the wind flow has been discussed as effective solutions to improve the wind velocity and circulation between the urban environment.

This study examines the wind shear coefficient (WSC) values at three coastal wind sites located in the southern region of Balochistan, Pakistan: Pasni, Ormara, and Jiwani. These WSC values were obtained using 10-minute measured wind speed data at heights of 20, 40, and 60 meters above ground level (AGL). Since wind measurements are typically recorded at lower heights due to cost and resource constraints, extrapolation techniques were employed to estimate wind speeds at higher altitudes. However, using a constant WSC value for extrapolation may lead to significant errors between extrapolated and actual wind speed measurements, impacting the energy output of wind turbines. To evaluate the effect of WSC on energy yield, the study employed power curves and frequency distributions for 2MW and 1.5MW wind turbines. Additionally, wind power density was calculated using air density derived from measured air temperature and surface pressure data, covering two years period from November 2016 to August 2018. The overall mean WSC values were found to be 0.076 at Pasni, 0.094 at Jiwani, and 0.053 at Ormara. The study further investigated the seasonal, monthly, and diurnal variations of WSC. For assessing wind resources at a height of 60m, the study utilized Wind Roses, wind power density, and Weibull parameters. Comparing the actual WSC values presented in this paper with those obtained using the 1/7 power law and measured data at 60m AGL, the energy yield from the wind turbines showed reduced output and capacity factor.

There is an accelerating requirement for ocean sensing where autonomous vehicles can play an essential role in assisting engineers, researchers, and scientists with environmental monitoring and collecting oceanographic data. This paper is performed to develop a rigid sail for the autonomous sailing drone. Our study aims to numerically analyze the aerodynamic characteristics of curvy twin sail and compare it with wing sail. Because racing regulations limit the sail shape, only the two-dimensional geometry was open for an optimization. Therefore, this study’s first objective was to identify the aerodynamic performance of such curvy twin sails. Simultaneously, a secondary objective was to estimate the effect of the sail’s spacing and shapes. A viscous Navier-Stokes flow solver is used for the numerical aerodynamic analysis. The 2D aerodynamic investigation is a preliminary evaluation. The results have shown that the curvy twin sail designs have improved lift, drag, and driving force coefficient compared to the wing sails. The spacing between the port and starboard sails of curvy twin sail is an important parameter. The spacing is 0.035L, 0.07L, and 0.14L shows the lift coefficient reduction because of dramatically stall effect, while flow separation is improved with spacing is 0.21L, 0.28L, and 0.35L. Significantly, the spacing 0.28L shows the maximum high pressure at the lower area and the small low pressure area at leading edges, so the highest lift is generated.

Offshore Wind Turbines (OWT) with increasingly higher energy output are being developed to meet energy demand, posing challenges for their foundation design. Several foundation types are used to support these turbines with monopiles (MP) accounting for 80% of the installed capacity. In this study, three-dimensional (3D) nonlinear finite element models (FEM) were employed to investigate the behaviour of monopile foundation supporting a 5MW wind turbine when subjected to lateral loading. Results indicate that the MP behavior depending on the pile length to diameter (L/D) ratio and the soil shear strength. Inspection of bending moment profiles at the lateral ultimate capacity indicated the monopiles can behave in flexible manner even with low L/D ratio. The L/D ratio affected the MP normalized lateral ultimate capacity at varying degrees and the biggest effect was for soft clays, amounting to around 5 folds increase for L/D values of 3.33 to 13.33. Lesser effects were found for stiff clays.

High-Rise buildings with their particular features can affects on surrounding environment and makes new microclimates. In the windy conditions, the spaces that are between building blocks changes to passages and affects on the wind velocity, intensity and it’s other parameters.The importance of this effect is different in each level of building height. The Pedestrian-Level is the lowest and one of important areas. Markets, playgrounds and pedestrian access had located in this area and any unwanted microclimate changes like high velocity and turbulence in this level can makes discomfort and dangerous condition for residents. So this research tries to consider the pedestrian- level wind comfort in some High-Rise building complexes arrangement that had located in Tehran district 22 with Computational Fluid Dynamics (CFD) modeling and reaching to a suitable arrangement pattern. It had collected the required data through field study and librarian databases and then compared them with standard guidelines and analyzed them by comparative comparison method. As a result a linear arrangement that placed crossover to wind direction for providing wind comfort and preventing wind danger is been suggested in this region.

The accuracy of wind field simulation and prediction is one of the most significant parameters in the field of atmospheric science and wind energy. Limited by the observation data, there are few researches on wind energy development. A 3D Doppler wind lidar (DWL) providing the high-vertical-resolution wind data over the urban complex underlying surface in February 2018 was employed to evaluated the accuracy of vertical wind field simulation systematically for the first time. 11 PBL schemes of the Weather Research and Forecasting Model (WRF) were employed in simulation. The model results were evaluated in groups separated by weather (sunny days, haze days and windy days), observation height layers, and various observation wind speeds. The test results presented that the vertical layer altitude of the observation point position was the most important factor. The simulation is fairly well at a height of 1000-2000m, as most of the relative mean bias of wind speed and wind direction are less than 20% and 6% respectively. Below 1000 m, the wind speed and direction biases are about 30%-150% m.s-1 and 6%-30% respectively. Moreover, when the observed wind speed was lower than 5 m.s-1, the bias were usually large, and the wind speed relative mean bias is up to 50-300%. In addition, the accuracy of simulated wind profile is better in 10-15m.s-1 than other speed ranges, and is better up 1000m than below 1000m in the boundary layer. We see that the WRF boundary layer schemes have different applicability to different weather conditions. The WRF boundary layer schemes have significant differences in wind field simulation with larger error under the complex topography. A PBL scheme is not likely to maintain its advantages in the long term under different conditions including altitude and weather conditions.

In Zambia, three feasibility studies have been conducted to assess the potential of wind energy for power generation. However, these studies did not investigate the capability of local support industries to manufacture wind turbine blades and towers. This study aimed to investigate and profile the capability of Zambian industries to manufacture wind turbine blades and towers. The study used a mixed-method approach to collect data; this utilized qualitative and quantitative approaches. The population of Zambian industries was collected from the Zambia Association of Manufacturers based on the registered members. This data was used to define the population for the study; the population was arranged into three strata whose characteristics are homogeneous within the stratum. Due to the low population, the study was conducted on the whole population. The qualitative data was collected from each stratum using a quantitative data collection tool developed for each stratum and analyzed. The study considered the capability of manufacturing companies based on wind potential results for Class III and Class IV, which exist in some sites. The results have revealed that on an as-is basis, no company in Zambia can manufacture WT blades and towers unless there is a complete overhaul of some companies or total investment in new infrastructure and equipment. The findings are useful for stakeholders involved in developing the wind power sector in Zambia.

Increasing wind speed alleviates physiological heat strain, however, health policies have advised against using ventilators or fans under heat wave conditions with air temperatures above the typical skin temperature of 35 °C. Recent research, mostly with sedentary participants, suggests mitigating effects of wind at even higher temperatures depending on the humidity level. Our study aimed at exploring and quantifying, whether such results are transferable to moderate exercise levels, and whether the Universal Thermal Climate Index UTCI reproduces those effects. We measured heart rates, core and skin temperatures and sweat rates in 198 laboratory experiments completed by five young, semi-nude, heat-acclimated, moderately exercising males walking the treadmill with 4 km/h on the level for three hours under widely varying temperature-humidity combinations and two wind conditions. We quantified the cooling effect of increasing wind speed from 0.3 to 2 m/s by fitting generalized additive models predicting the physiological heat stress responses depending on ambient temperature, humidity and wind speed. We then compared the observed wind effects to the assessment performed by UTCI. Increasing wind speed lowered physiological heat strain for air temperatures below 35 °C, but also for higher temperatures with humidity levels above 2 kPa water vapour pressure concerning heart rate and core temperature, and 3 kPa concerning skin temperature and sweat rate, respectively. UTCI assessment of wind effects correlated positively with the observed changes in physiological responses, showing the closest agreement (r=0.9) for skin temperature and sweat rate, where wind is known for elevating the relevant convective and evaporative heat transfer. These results demonstrate the potential of UTCI for adequately assessing sustainable strategies for heat stress mitigation involving fans or ventilators depending on temperature and humidity for moderately exercising individuals.

Taiwan developing offshore wind power to promote green energy and self-electricity production. In this study, a Light Detection and Ranging (Lidar) was set up at Chang-Hua development zone one on the sea and 10km away from the seashore. At Lidar location, WRF (3.33km & 2km grid lengths) model and WAsP were used to simulate the wind speed at various elevations. Three days mean wind speed of simulated results were compared with Lidar data. From the four wind data sets, developed five different comparisons to find an error% and R-Squared values. Comparison between WAsP and Floating Lidar was shown good consistency. Lukang meteorological station 10 years wind observations at 5m height were used for wind farm energy predictions. The yearly variation of energy predictions of traditional and TGC wind farm layouts are compared under purely neutral and stable condition. The one-year cycle average surface heat flux over the Taiwan Strait is negative (-72.5 (W/m2) and 157.13 STD), which represents stable condition. At stable condition TGC (92.39%) and 600(92.44%), wind farms were shown higher efficiency. The Fuhai met mast wind data was used to estimate roughness length and power law exponent. The average roughness lengths are very small and unstable atmosphere.

This paper presents a system for identification of wind features, such as gusts and wind shear. These are of particular interest in the context of energy-efficient navigation of Small Unmanned Aerial Systems (UAS). The proposed system generates real-time wind vector estimates and a novel algorithm to generate wind field predictions. Estimations are based on the integration of an off-the-shelf navigation system and airspeed readings in a so-called direct approach. Wind predictions use atmospheric models to characterize the wind field with different statistical analyses. During the prediction stage, the system is able to incorporate, in a big-data approach, wind measurements from previous flights in order to enhance the approximations. Wind estimates are classified and fitted into a Weibull probability density function. A Genetic Algorithm (GA) is utilized to determine the shaping and scale parameters of the distribution, which are employed to determine the most probable wind speed at a certain position. The system uses this information to characterize a wind shear or a discrete gust and also utilizes a Gaussian Process regression to characterize continuous gusts. The knowledge of the wind features is crucial for computing energy-efficient trajectories with low cost and payload. Therefore, the system provides a solution that does not require any additional sensors. The system architecture presents a modular decentralized approach, in which the main parts of the system are separated in modules and the exchange of information is managed by a communication handler to enhance upgradeability and maintainability. Validation is done providing preliminary results of both simulations and Software-In-The-Loop testing. Telemetry data collected from real flights, performed in the Seville Metropolitan Area in Andalusia (Spain), was used for testing. Results show that wind estimation and predictions can be calculated at 1 Hz and a wind map can be updated at 0.4 Hz. Predictions show a convergence time with a 95% confidence interval of approximately 30 s.

Growing population, industrialization, and power requirements are adversely affecting the environment by increased greenhouse gases, resulting from fossil fuel burning. Global greenhouse gas mitigation targets have led the nations to promote clean and self-renewable sources of energy to address the environmental issue. Offshore wind power resources are relatively more attractive due to high winds, less turbulence, minimal visualization effects, and no interaction of infrastructure. The present study aims at conducting offshore wind power resources assessment (OWPRA) at some locations in the Gulf of North Suez. For this purpose, the long-term hourly mean wind speed (WS) and wind direction above means sea level (AMSL) and temperature and pressure data near surface is used. The data is obtained from ERA5 (fifth generation reanalysis for the global climate weather) at chosen six (L1-L6) offshore locations. The data covers a period of 43 years, between 1979 and 2021. The WS and direction are provided at 100 m AMSL while temperature and pressure are available near water surface level. At L1 to L6 locations, the log-term mean WS and wind power density (WPD) values are found to be 7.55 m/s and 370 W/m2, 6.37 m/s and 225 W/m2, 6.91 m/s and 281 W/m2, 5.48 m/s and 142 W/m2, 4.30 m/s and 77 W/m2, and 5.03 and 115 W/m2 and at 100 m AMSL; respectively. The higher magnitudes of monthly and annual windy site identifier indices (MWSI and AWSI) of 18.68 and 57.41 and 12.70 and 42.94 at L1 and L3 sites and generally lower values of wind variability indices are indicative of favourable winds source, which is also supported by higher magnitudes of mean WS, WPD, annual energy yields, plant capacity factors, and wind duration at these sites. The cost of energy, for the worst and the best cases are estimated as 10.120 USD/kWh and 1.274 USD/kWh at L5 and L1 sites corresponding to wind turbines WT1 and WT4. Based on the analysis, sites L1, L3, and L2 are recommended for wind farm development in order of preference. The wind variability and windy site identifiers indices introduced, will help decision-makers in deciding the potential windy sites with more confidence.

Wind power output is highly dependent on the wind speed at the selected site, therefore wind-speed distribution modeling is the most important step in the assessment of wind energy potential. This study aims at accurate evaluation of onshore wind energy potential in seven coastal cities in the south of Iran. Six Probability Distribution Functions (PDFs) were examined over representative stations. It has been deduced that the Weibull function, which was the most used PDF in similar studies, was only applicable to one station. Here, Gamma offered the best fit for three stations and for the other ones, Generalized Extreme Value (GEV) performed better. Considering the ranking of six examined PDFs and the simplicity of Gamma, it was identified as the effective function in the southern coasts of Iran bearing in mind the geographic distribution of stations. Besides, six turbine power curve functions were contributed to investigate the capacity factor. That was very important, as using only one function could cause under- or over-estimation. Then, stations were classified based on the National Renewable Energy Laboratory system. Last but not least, examining a range of wind turbines enabled scholars to extend this study into the practice and prioritize development of stations considering budget limits.

The use of wind energy has been developing fast over the last years. The global cumulative wind power capacity increased by 10.5% in 2019, most of which comes from onshore wind farms. One of the consequences of this continuous increase is the use of land for onshore wind farms. There are already cases worldwide where lack of well-established plans and strategies have caused delays in projects. The need for efficiently using land for wind farms will be mandatory in the short term. In this work, we present a numerical analysis to evaluate wind farm land-use. By defining the ratio between mechanical output power over an area as a parameter called land-use ratio, this work focused on comparing several cases of aligned and staggered layouts. Mechanical output power was estimated using a validated code based on Blade Element Momentum code, and the wake velocities and wake interaction effects were estimated using a validated wind turbine CFD model. In terms of output power, staggered designs are more efficient than aligned designs. However, the results showed that even though staggered designs produced higher output power, aligned farms with tight lateral spacing could be as efficient as staggered ones in terms of land-use but using fewer turbines. In summary, tightly aligned designs should be a tendency in the future towards efficient use of land in wind farms.

This study investigates the power production and blade fatigue of a three-turbine array subjected to active yaw control (AYC) in full-wake and partial-wake configurations. A framework of two-way coupled large-eddy simulation (LES) and aeroelastic blade simulation is applied to simulate the atmospheric boundary-layer (ABL) flow through the turbine array and the structural responses of the turbine blades. Mean power outputs and blade fatigue loads are extracted from the simulation results. By exploring the feasible AYC decision space, we find that (a) in the full-wake configuration, the local power-optimal AYC strategy with positive yaw angles endures less flapwise blade fatigue and more edgewise blade fatigue than the global power-optimal strategy; (b) in the partial-wake configuration, applying positive AYC in certain inflow wind directions achieves higher optimal power gains than that in the full-wake scenario and reduces the blade fatigue from the non-yawed benchmark. Through a theoretical analysis based on the blade element momentum theory, we reveal that the aforementioned differences in flapwise blade fatigue between the positively and negatively yawed turbine are due to the differences in the azimuthal distributions of the local relative velocity on blade sections, resulting from the combined effects of vertical wind shear and blade rotation. Furthermore, the difference in the blade force between the positively and negatively yawed front-row turbine induces different wake velocity and turbulence distributions, causing different fatigue loads on the downwind turbine exposed to the wake.

Full-scale wind turbine technology has been widely developing in the recent years and condition monitoring techniques assist at the scope of making 100\% technical availability a realistic perspective. In this context, several retrofitting techniques are being used for further improving the efficiency of wind kinetic energy conversion. This kind of interventions is costly and, furthermore, the estimation of the energy enhancement is commonly provided under the hypothesis of ideal conditions, as for example absence of wakes between nearby turbines. A precise quantification of the energy gained by retrofitting is therefore precious in real conditions, that can be very different from ideal ones. In this work, three kinds of retrofitting are studied through the operational data of test case wind farms: improved start-up through pitch angle adjustment near the cut-in, aerodynamic blade retrofitting by means of vortex generators and passive flow control devices, extension of the power curve by raising cut-out and high wind speed cut-in. SCADA data are employed and reliable methods are formulated for estimating the energy improvement from each of the above retrofitting. Further, an insight is provided about wind turbine functioning under very stressing regimes, as for example high wind speeds.

Small wind turbines placed at City locations are affected by variable speed winds that frequently also change the direction. Architectural constructions, buildings of different height and abrupt orography of Cities make the winds that occur at City locations, more variable than in flat lands or at sea. However, performance of Small-wind turbines under this type of variable winds is not deeply studied in specialized literature. Therefore, this article analyses this important issue, also considering three types of power conversion configurations utilized in small-wind turbines; the generally used Maximum Power Point Tracking (MPPT) configuration, the simple only-rectifier configuration and an intermediate configuration in terms of complexity called Pseudo-MPPT. This general-purpose analysis is applied to a specific type of wind turbine, i.e. the Ayanz wind turbine with screw blades, which presents very adequate characteristics for city locations such as; safety, reduced visual and acoustic impacts and birds’ casualties avoidance. Thus, a wide simulation and experimental tests-based analysis is carried out, identifying which are the main factors affecting to the maximization of energy production of small-wind turbines in general and the Ayanz turbine in particular. It is concluded that depending how the wind turbine is designed in terms of these identified main factors, the simple Pseudo-MPPT power conversion configuration could even extract more energy than more complex MPPT configurations, especially in quickly varying wind situations.

The present studies are specifically aimed at investigating the sensitivity of different dynamic stall models when exposed to various excitation frequencies targeted at the blade edgewise vibrations. The work is done on a modified version of the IEA 15 MW reference wind turbine employing a wind turbine design tool Bladed. The state-of-the-art dynamic stall models for wind turbine applications such as the ye model, Beddoes-Leishman (BL) model and the newly developed IAG model are evaluated. The beginning of the research work starts by evaluating different dynamic stall model effects on rigid blade section forces against known airfoil datasets. Then, the blade flexibility is considered to enable systematic evaluations of the blade flexibility influences in comparison to the rigid blade cases. It is observed that the range of the angle of attack grows depending on the excitation frequency and the adopted dynamic stall model. The critical excitation frequency range and the effects of twist distribution are then identified from the studies, which can be useful as a rough guidance when designing wind turbine blades.

Considering that traditional energy sources such as fossil fuel are about to deplete during the following decades, governments try to turn to renewable energy. It is commonly known that Greece has a natural advantage of abundant solar energy and wind power due to its geographical location and characteristics.The main focus of this study is to examine how wind energy potential across the Aegean Sea and continental Greece can provide a promising field for investments in Greece, considering the economic crisis, current trends and future perspectives.We firstly focus on current legislation framework considering that laws associated with such types of investment in Greece are very complex and rapidly changing. Furthermore, a case study for a hypothetical investment plan concerning a wind park located in an Aegean island will be presented. RetScreen which is a software made by the Canadian government, will be used as a decision support tool for analyzing the potential investment scenario and a financial report will follow with estimation of the overall cost, depreciation, upcoming benefits, and payback period of the investment.Data analysis concludes that wind parks still prove to be an economically viable investment, although incentives considering the guaranteed price per kwh and faster investment times must be provided by the government.

The kinetic energy transfer between the atmosphere and oceans, called wind work, affects ocean dynamics including near-inertial oscillations and internal gravity waves, mesoscale eddies, and large-scale zonal jets. For the most part, recent numerical estimates of global wind work amplitude are almost 5 times larger than those reported 10 years ago. This large increase is explained by the impact of the broad range of spatial and temporal scales covered by winds and currents, the smallest of which have only recently been uncovered by increasingly high resolution modeling efforts. However, existing satellite observations do not fully sample this broad range of scales. The present study assesses the capabilities of ODYSEA, a conceptual satellite mission to estimate the amplitude of wind work in the global ocean. To this end, we use an ODYSEA measurement simulator fed by the outputs of a km-scale coupled ocean-atmosphere model to estimate wind work globally. Results indicate that compared with numerical truth estimates, the ODYSEA instrument performs well globally, except for latitudes north of 40∘N during summer due to unresolved storm evolution. This performance is explained by the wide-swath properties of ODYSEA (a 1,700 km wide swath with 5 km posting for winds and surface currents), its twice-a-day (daily) coverage at mid-latitudes (low latitudes), and the insensitivity of the wind work to uncorrelated errors in estimated wind and current.

Considering the dynamic stall effects in engineering calculations is essential for correcting the aerodynamic loads acting on wind turbines, both during power production and stand-still cases, and impacts significantly the turbine aeroelastic stability. The employed dynamic stall model needs to be accurate and robust for a wide range of airfoils and range of angle of attack. The present studies are intended to demonstrate the performance of a recently implemented "IAG dynamic stall" model in a wind turbine design tool Bladed. The model is transformed from the indicial type of formulation into a state-space representation. The new model is validated against measurement data and other dynamic stall models in Bladed for various flow conditions and airfoils. It is demonstrated that the new model is able to reproduce the measured dynamic polar accurately without airfoil specific parameter calibration and has a superior performance compared to other models in Bladed.

For the Philippines, a country exposed to multiple natural hazards like severe wind, sustainable development includes resiliency. Severe wind hazard is brought by tropical cyclones in the Western Pacific, known as typhoons, that frequent the Philippines. Therefore, adequately evaluating the wind hazard and its impact is crucial for sustainable building design. Acknowledging the impacts of climate change on said hazards would require adaptation to its consequences which necessitate a deeper understanding on the changing behavior of typhoons in recent years. For this study, detailed wind information from the Japan Meteorological Agency from 1977-2021, the Holland-B parameter, and the radius of maximum wind speed for each typhoon, are determined for simulation of the regional cyclonic wind field. The analysis of the Holland-B parameters, which represent the steepness of the pressure gradient and tropical cyclone convection, suggest that the Holland-B parameters have been increasing since 2011. The regional wind fields caused by the typhoons also suggest an increasing trend in severe wind hazard. Seasonality for the location of severe wind hazard is also observed, with the Southern Philippines experiencing an increase (decrease) during the Northeast (Southwest) Monsoon season, and the Northern Philippines experiencing an increase (decrease) during the Southwest (Northeast) Monsoon season.

Wind energy is becoming an essential source of power for countries which have the aim to reduce greenhouse gases emission and mitigate the effects of global warming. The Wind Turbines (WTs) installed around the globe is increasing significantly every year. The dramatic increase in wind power has encountered quite a few challenges, among which the major issues are availability and reliability. The unexpected failure in WTs Gearbox (GB) ultimately increases the Operation and Maintenance (O&M) cost. The identification of faults in the earlier stages before it turns to catastrophic damage to other components of WT is crucial. This research deals with the prediction of WT failures by using a Supervisory Control and Data Acquisition (SCADA) system. The main aim is to forecast the temperature of the WTs GB to predict the impending overheating of the GB at an early stage. The earlier prediction will help to optimize the maintenance period and to save maintenance expenses and, even more important, generate warnings in due time to avoid major damages or even technical disasters. In the proposed method we compared six different machine learning (ML) models based on error and accuracy of prediction. The bagging regressor is the best ML model, which results in the mean square error of 0.33 and R of 99.8 on training data. The bagging regressor is then used to predict the fault in the WT GB, which detected the anomalous behavior of WT GB 59 days earlier than the actual failure. This model also detects the extremely unusual behavior of the GB 9 days earlier than a complete failure.

The global energy crisis has lead researchers explore other sources of energy like wind, resulting in a wide acceptance of wind turbines. Vertical axis wind turbines (VAWT) more suitable for small scale application in urban conditions than their horizontal-axis counterparts. A Helical bladed VAWT would reduce the ripple effect when compared to Straight bladed VAWT. The effect of the blade helix angle on the aerodynamic performance of VAWT using 3D numerical simulations is studied. Turbulence modelled using 4-Equation transition SST k-w model. Three different helix angles of 60, 90 and 120 of a 3 bladed VAWT operating across different tip speed ratios were studied. The 60 helical bladed VAWT was found to perform better than all other helical bladed and straight bladed VAWT. Standard deviation of the moment coefficient generated by a blade plotted against 360 of azimuth rotation revealed that the ripple effect on the shaft produced by cyclic loading of the straight blade is considerably reduced upon introduction of helix angle, with 120 helical blade giving lowest standard deviation. The analysis has been done for the percentage of power generated by each quartile of flow and the contribution of each section of the blade. A comparative study was also conducted between different helical bladed VAWT and straight bladed VAWT. Flow feature analysis also revealed the reasons behind secondary peaks and the performance improvement when tip speed ratio increases. Wake structure analysis and flow contours were also studied for a better understanding of the flow field.

The research sought to investigate the long term characteristics of wind in the Kisii region (elevation 1710m above sea level, 0.68^oS, 34.79^o E). Wind speeds were analyzed and characterized on short term (per month for a year) and then simulated for long term (ten years) measured hourly series data of daily wind speeds at a height of 10m. The analysis included daily wind data which was grouped into discrete data and then calculated to represent; the mean wind speed, diurnal variations, daily variations as well as the monthly variations. The wind speed frequency distribution at the height 10 m was found to be 2.9ms^-1 with a standard deviation of 1.5. Based on the two month’s data that was extracted from the AcuRite 01024 Wireless Weather Stations with 5-in-1 Weather Sensor experiments set at three sites in the region, averages of wind speeds at hub heights of 10m and 13m were calculated and found to be 1.7m/s, 2.0m/s for Ikobe station, 2.4m/s, 2.8m/s for Kisii University stations, and 1.3m/s, 1.6m/s for Nyamecheo station respectively. Then extrapolation was done to determine average wind speeds at heights (20m, 30m, 50m, and 70m) which were found to be 85.55W/m², 181.75W/m², 470.4W/m² and 879.9W/m² respectively. The wind speed data was used statistically to model a Weibull probability density function and used to determine the power density for Kisii region.

This paper proposes a procedure for predicting the actual wind speed for flow over complex terrain with CFD. It converts a time-series of wind speed data acquired from field observations into a time-series of actual scalar wind speed by using non-dimensional wind speed parameters which are determined beforehand with the use of CFD output. The accuracy and reproducibility of the prediction procedure were examined by simulating the flow with CFD with the use of high resolution (5 m) surface elevation data for the Noma Wind Park in Kagoshima Prefecture, Japan. The errors of the predicted average monthly wind speeds relative to the observed values were less than approximately 20%.

Study assessed the wind potential of three sites in Chad: Koro Toro, Salal and Nedeley. Analysis of the Weibull distribution curves reveals marked seasonal variability in wind speed, concentrated around the mean. Three models of high-power wind turbines were analyzed. At Koro Toro, the Siemens Gamesa SG 14-222 DD has a capacity factor of between 0.52 and 0.682, allowing a daily flow of pumped water of between 1.4 and 6.1 million m³. The Enercon E-126 EP4 performs slightly less well. At Salal, the Siemens Gamesa has a capacity factor of between 0.4463 and 0.6605, with a water flow rate of between 0.9 and 3.7 million m³/day. The Vestas V164-10.0 MW has a higher capacity factor (0.6327 to 0.8115) but a lower water flow rate (0.5 to 1.9 million m³/day). Enercon's performance is comparable to that of Siemens Gamesa. The Nedeley study reveals favorable conditions, with seasonal variations in wind speed and capacity factor indicating good wind potential, and maximum daily water flows of between 3 and 6 million m³. Analysis of the wind roses shows interesting potential in these towns, with a dominant east-north-easterly wind at maximum frequencies of 40%. The absence of calm winds is promising, although Nedeley and Salal have a residual presence. This study shows that the sites offer good wind potential This, enabling the production of electricity and heat.

This article presents the suitability analysis of onshore wind farm sites using an AHP (Hierarchical Analysis Process) multi-criteria decision-making (MCDM) approach based on geographic information system modeling (GIS). This analysis is based on different technical aspects (wind speed, elevation, slope), economic (proximity to the electricity network, proximity to roads) and social (proximity to residential areas, population density). The introduction of the factor “population density” and the constraint “required area” rarely used in previous studies makes it possible to refine the results. The data is classified into several categories in a gradual manner, namely unsuitable (0); less suitable (1); suitable (2); highly suitable (3) and most suitable (4). The results of the study show us that the largest percentage relating to spatial coverage is observed in the “suitable” range with 50.89% and the corresponding TWPP (theoretical wind power potential) is 1377.926 GW; it is followed by “highly suitable” 5.67% and a TWPP of 153.652 GW; then “less suitable” with 1.04% and a TWPP of 28.163GW. No areas were identified in “most suitable” and finally the “unsuitable” range with 42.4%. The results show that the most favorable areas are located in the part of the far north of the country corresponding to the strong wind zone. The sensitivity analysis was carried out based on scenario tests (technical, economic and equal-weight) in order to give greater visibility of choice to the different stakeholders who would like to invest in onshore wind energy in Cameroon. This study is useful in more than one way because the results obtained can help investors, the government and other stakeholders to identify potential areas for the deployment of wind energy systems in Cameroon. Furthermore, a study of hybrid solar-wind systems could improve the efficiency of electricity parks in Cameroon.

When undertaking wind assessment around buildings using large eddy simulation (LES), the implementation of the integral length scale at the inlet for inflow generation is controversial, as real atmospheric length scales require huge computational domains. While length scales significantly influence inflow generation in the domain, their effect on the downstream flow field has not yet, been investigated. In this paper, we validate the effectiveness and accuracy of implementing a reduced turbulence integral length scale for inflow generation in LES results at the rooftop of low-rise buildings and develop a technique to estimate the real local length scales using simulation results. We measure the wind locally and calculate the turbulence length scales from the energy spectrum of the wind data and simulation data. According to these results, there is an excellent agreement between the length scale from simulation and measurement when they are scaled with their corresponding freestream/inlet value. These results indicate that a reduced integral length scale can be safely used for LES to provide a reliable prediction of the energy spectrum as well as the length scales around complex geometries. The simulation results were confidently employed to obtain the best location for a wind turbine installation on low-rise buildings.

The high-resolution bistatic lidar developed at the Physikalisch-Technische Bundesanstalt (PTB) aims to overcome the limitations of conventional monostatic lidar technology which is widely used for wind velocity measurements in wind energy and meteorology applications. Due to the large measurement volume of a combined optical transmitter and receiver tilting in multiple directions, monostatic lidar generally has poor spatial and temporal resolution. It also exhibits large measurement uncertainty when operated in inhomogeneous flow, for instance, over complex terrain. In contrast, PTB’s bistatic lidar uses three dedicated receivers arranged around a central transmitter, resulting in an exceptionally small measurement volume. The coherent detection and modulation schemes used allow the detection of backscattered, Doppler shifted light down to the scale of single aerosols, realising the simultaneous measurement of all three wind velocity components. This paper outlines design details and the theory of operation of PTB’s bistatic lidar and provides an overview of selected comparative measurements. The results of these measurements have shown that the measurement uncertainty of PTB’s bistatic lidar is well within the measurement uncertainty of traditional cup anemometers, while being fully independent of its site and traceable to the SI units. This allows its use as a transfer standard for the calibration of other remote sensing devices. Overall, PTB’s bistatic lidar shows great potential to universally improve the capability and accuracy of wind velocity measurements, such as for the investigation of highly dynamic flow processes upstream and in the wake of wind turbines.

In this paper, four probability functions are compared with the purpose of establishing a methodology to improve the accuracy of the estimated wind energy in a desert city in northwestern Mexico. For the statistical modeling, 3 time series of wind speed data were used, corresponding to the years 2017, 2018, and 2019, recorded with a sonic anemometer at a sampling frequency of 10 Hz. From these, the analysis is performed with different stationarity periods (5, 30, 60, and 600 seconds). The estimation of the parameters characterizing the probability density functions was performed using different methods; the statistical models were evaluated by the coefficient of determination and the Nash-Sutcliffe efficiency coefficient, while their accuracy by the measured quadratic error, the mean square error, the mean absolute error, and the mean absolute percentage error. It was found that Weibull with the energy pattern factor method and Gamma using the method of moments were the probability density functions that best describe the statistical behavior of the wind speed and, therefore, better estimate the energy generated, so it is concluded that the proposed methodology will allow having greater confidence, both in the estimation of the wind speed and in the small wind energy available for its use.

The most important step for the installation of a wind farm is to know the wind regime in the region, since an error in estimating this wind speed causes an error proportional to the cube of power, resulting in financial losses for investors. Therefore, knowing the methods used for predicting wind speed becomes important and the knowledge of how research and studies in this area are going helps map the subject and outline strategies for developing research in strategic areas. For this purpose, the Scopus database was used considering some keywords, such as ("forecast" OR "prevision") AND "wind" AND ("turbine" OR "power" OR "energy" or "velocity" or "speed"), considering the period since 2019, and analyzing the data of the documents found using the Bibliometrix package. With the results found, it was possible to map researchers, institutions that are developing work in this area, in addition to the most cited articles, among other aspects analyzed.

Green hydrogen is likely to play an important role in meeting the net zero targets of countries around the globe. Hence, producing green hydrogen cheaply and effectively is an important area of research. One potential option for green hydrogen production is to run electrolysers directly from offshore wind turbines, with no grid connection and hence no expensive cabling to shore. The removal of the grid presents an unusual integration challenge. The variable nature of wind turbines and farms results in a power output that can fluctuate more quickly than the electrolyser’s ability to respond without significantly stressing the electrolyser. Thus, the use of a battery, with the wind farm, becomes essential to even out some of the power variations that the electrolyser cannot deal with. In this work, a proof of concept of a wind farm control methodology designed to reduce variability in wind farm active power output is presented. Smoothing the power supplied by the wind farm to the battery reduces the size and number of battery charge cycles and helps to increase battery lifetime. Considering off-grid wind farms which exclusively power an electrolyser, this work quantifies the impact of the wind farm control method on battery lifetime for wind farms of 1, 4, 9 and 16 wind turbines. This is achieved using suitable wind farm, battery and electrolyser models. As an example, for the largest wind farm studied, consisting of 16 x 5 MW wind turbines, batteries with a lifetime of 15 years have approximately a 30 % reduction in required capacity (reduced from 14 MWh to 10 MWh) compared to operating without wind farm control. It is found that reducing the variability of the active power output of wind farms through the wind farm control methodology presented can have a significant impact on battery degradation and hence on battery lifetime. Hence, wind farm control can reduce the required battery capacity for a given lifetime or it can increase the lifetime of a given battery capacity. The work presented shows that wind farm control could play a critical role in reducing the levelised cost of green hydrogen produced from wind farms with no grid connection and paves the way for the design and testing of a full implementation of the wind farm control.

Aerodynamic performance of a floating offshore wind turbine (FOWT) is significantly influenced by platform surging motions. Accurate prediction of the unsteady aerodynamic loads is imperative for determining the fatigue life, ultimate loads on key components such as FOWT rotor blades, gearbox and power converter. The current study examines the predictions of numerical codes by comparing with unsteady experimental results of a scaled floating wind turbine rotor. The influence of platform surge amplitude together with the tip speed ratio on the unsteady aerodynamic loading has been simulated through unsteady CFD. It is shown that the unsteady aerodynamic loads of FOWT are highly sensitive to the changes in frequency and amplitude of the platform motion. Also, the surging motion significantly influences the windmill operating state due to strong flow interaction between the rotating blades and generated blade-tip vortices. Almost in all frequencies and amplitudes, CFD, LR-BEM and LR-uBEM predictions of mean thrust shows a good correlation with experimental results.

To investigate the optimum layouts of small vertical axis wind turbines, a two-dimensional analysis of dynamic fluid body interaction is performed via computational fluid dynamics for a rotor pair in various configurations. The rotational speed of each turbine rotor (diameter: D = 50 mm) varies based on the equation of motion. First, the dependence of rotor performance on the gap distance (gap) between two rotors is investigated. For parallel layouts, counter-down (CD) layouts with blades moving downwind in the gap region yield a higher mean power than counter-up (CU) layouts with blades moving upwind in the gap region. CD layouts with gap/D = 0.5–1.0 yield a maximum average power that is 23% higher than that of an isolated single rotor. Assuming isotropic bidirectional wind speed, co-rotating (CO) layouts with the same rotational direction are superior to the combination of CD and CU layouts regardless of the gap distance. For tandem layouts, the inverse-rotating configuration (IR) shows an earlier wake recovery than the CO configuration. For 16-wind-direction layouts, both the IR and CO configurations indicate similar power distribution at gap/D = 2.0. For the first time, this study demonstrates the phase synchronization of two rotors via numerical simulation.

Combining wind and solar photovoltaic (PV) generation can provide complementary renewable power production, but depends on correlated resources. This study analyzed 10 years of wind data from Naama, Algeria to evaluate the potential for evening wind generation to offset the loss of solar at sunset. Average wind speeds showed a distinct increase during evening hours, coinciding with the decrease in solar irradiance. Wind turbine simulations using a 1.5 MW turbine and the wind data showed sufficient resources for profitable power production after sunset. Statistical analyses confirmed significantly higher wind speeds and simulated power output in evening vs daylight periods (p<0.05). The Pearson correlation coefficient between evening wind speeds and decreasing solar irradiance was 0.63, supporting a strong positive relationship. These findings indicate Naama has adequate wind resources to deploy economically viable wind power capacity that can complement existing solar infrastructure and provide renewable electricity after dark , .

This research introduces a novel approach to improving wind energy's LCOE (Levelised Cost of Energy). Specifically, this research aims to reduce the LCOE from wind turbines by investigating a novel Active Axis Wind Turbine (AAWT) design. The turbine is neither a horizontal nor vertical axis wind turbine but has an axis of operation that can actively change during operation. The design features a rotor with a single blade capable of dynamic pitch and tilt control during a single rotor rotation. This study examines the potential to balance the centrifugal and aerodynamic lift forces acting on the rotor blade assembly, significantly reducing blade, tower, foundation and infrastructure costs in larger-scale devices and decreasing the LCOE for wind. The design of a laboratory prototype rotor assembly is optimised by varying the masses and lengths in a lumped mass model to achieve equilibrium between centrifugal and lift forces acting on the turbine's rotor assembly. The method involves an investigation of the variation of blade pitch angle to provide a balance between centrifugal and aerodynamic forces, thereby facilitating the cost advantages and opening the opportunity to improve the turbine efficiency across a range of operation conditions. The implication of this study extends to different applications of wind turbines, both onshore and offshore, introducing insight into innovation for sustainable energy and cost-effective solutions.

Advancements in technology, policies, and cost reductions have led to rapid growth in wind power production. One of the major challenges in wind energy production is the instability of wind power generation due to weather changes. Efficient power grid management requires accurate power output forecasting. New wind energy forecasting methods based on deep learning are better than traditional methods, like numerical weather prediction, statistical models, and machine learning models. This is more true for short-term prediction. Since there is a relationship between methods, climates, and forecasting complexity, forecasting methods do not always perform the same depending on the climate and terrain of the data source. This paper proposes a novel model that combines the variational mode decomposition method with a long short-term memory model, developed for next-hour wind speed prediction in a hot desert climate, such as the climate in Saudi Arabia. We compared the proposed model performance to two other hybrid models, six deep learning models, and four machine learning models using different feature sets. Also, we tested the proposed model on data from different climates, Caracas and Toronto. The proposed model showed a forecast skill between 61% to 74% based on mean absolute error, 64% to 72% based on root mean square error, and 59% to 68% based on mean absolute percentage error for locations in Saudi Arabia.

Management approaches inspired by the variability of natural disturbances are expected to produce forests in the future that will be significantly more resilient and better adapted to local environmental conditions. Due to climate change, windstorms are becoming increasingly common resulting in the destruction not only of extensive forest areas but, quite often, of small-sized and scattered forest lands that can ultimately become home to insects and disease dissemination sites. In the present study, an attempt is made to identify and record areas in the northeastern forests of Greece covered by mixed stands of conifers and broadleaves that experienced massive windthrow following local storms. Based on tree-level data, local topographic features, forest characteristics and the mechanical properties of green wood, a reliable model, to be used for the prediction of similar disturbances in the future, has been created after a thorough comparative study of the most well-known intelligent machine learning algorithms.

A modified free-wake vortex ring model is proposed to compute the dynamics of a floating horizontal-axis wind turbine. The model is divided into two parts. The near wake model uses a blade bound vortex model and trailed vortex model, which is developed based on vortex filament method. By contrast, the far wake model is based on the vortex ring method. The proposed model is a good compromise between accuracy and computational cost, for example when compared with more complex vortex methods. The present model is used to assess the influence of floating platform motions on the performance of a horizontal-axis wind turbine rotor. The results are validated on the 5MW NREL rotor and compared with other aerodynamic models for the same rotor subjected to different platform motions. It was found that the results from the proposed method are more reliable than the results from BEM theory especially at small angles of attack in the region of low wind speeds, on the one hand, and high wind speeds with blade pitch motions, on the other hand. And also the proposed method is less time consuming and has similar accuracy when comparing with more advanced vortex based methods.

Wind turbine upgrades have been spreading in the recent years in the wind energy industry, with the aim of optimizing the efficiency of wind kinetic energy conversion. This kind of interventions has material and labor costs and it is therefore fundamental to estimate realistically the production improvement. Further, the retrofitting of wind turbines sited in harsh environments might exacerbate the stressing conditions to which wind turbines are subjected and consequently might affect the residue lifetime. This work deals with a case of retrofitting: the testing ground is a multi-megawatt wind turbine from a wind farm sited in a very complex terrain. The blades have been optimized by installing vortex generators and passive flow control devices. The complexity of this test case, dictated by the environment and by the features of the data set at disposal, inspires the formulation of a general method for estimating production upgrades, based on multivariate linear modeling of the power output of the upgraded wind turbine. The method is a distinctive part of the outcome of this work because it is generalizable to the study of whatever wind turbine upgrade and it is adaptable to the features of the data sets at disposal. In particular, applying this model to the test case of interest, it arises that the upgrade increases the annual energy production of the wind turbine of an amount of the order of the 2%. This quantity is of the same order of magnitude, albeit non-negligibly lower, than the estimate based on the assumption of ideal wind conditions. Therefore, it arises that complex wind conditions might affect the efficiency of wind turbine upgrades and it is therefore important to estimate their impact using data from wind turbines operating in the real environment of interest.

In the context of the Korean building structure standard KDS2022, wind loads can be readily calculated in terms of the along-wind, across-wind, and torsional components, based on a single wind direction. However, this approach falls short in accurately and safely evaluating the impact of winds from various directions. Therefore, in this study, we developed a Wind Load Calculation Program (WCP) capable of predicting wind loads with relative precision during the preliminary design phase. First, wind tunnel tests were conducted to identify the essential factors necessary for calculating wind loads and the variables influencing these factors. The building shape considered was a square, and the wind force coefficients and power spectral density were measured by combining 4 ground roughness values, 11 side ratios (), 4 aspect ratios (), and wind directions ranging from 0° to 90°. Subsequently, a generalized formulation was devised to facilitate wind load calculations across diverse conditions and a method for calculating load combination coefficients, considering response correlation and load simultaneity, was presented. Finally, the wind loads obtained from the wind tunnel tests were compared with those predicted by the WCP using an actual project model.

The wind observations for multiple levels (40–200 m) have been conducted for a long time (2016–2020) on Jeju Island of South Korea. This study aims at understanding the vertical and temporal characteristics of lower atmosphere. Jeju Island is a region located at mid-latitude and is affected by seasonal monsoon wind. The maximum wind speed appears in the lower layer during day time and is delayed in the upper layer during latter time in diurnal cycle. In summer season, the surface layer increases up to 160 m during day time via dominant solar radiation effect, which is higher than those for other seasons. However, the maximum wind speed in winter season appears irregularly among altitudes, and the surface layer is ~100 m, which is lower than that in summer season. It can be attributed to the increase in the mean wind speed in diurnal cycle caused by the strong northwestern wind for winter season. These results imply that the relationship between near-surface and higher altitudes is primarily affected by solar radiation and seasonal monsoon winds. These results are expected to contribute to site selection criteria for wind farms and to the assessment concerning planetary boundary layer modeling.

The unsteady Ekman problem involves finding the response of the near-surface currents to wind stress forcing under linearized dynamics. Its solution can be conveniently framed in the frequency domain in terms of a quantity that is known as the transfer function, the Fourier transform of the impulse response function. In this paper, a theoretical investigation of a fairly general transfer function form is undertaken with the goal of paving the way for future observational studies. Building on earlier work, we consider in detail the transfer function arising from a linearly-varying profile of the vertical eddy viscosity, subject to a no-slip lower boundary condition at a finite depth. The linearized horizontal momentum equations are shown to transform to a modified Bessel’s equation for the transfer function. Two self-similarities, or rescalings that each effectively eliminate one independent variable, are identified, enabling the dependence of the transfer function on its parameters to be more readily assessed. A systematic investigation of asymptotic behaviors of the transfer function is then undertaken, yielding expressions appropriate for eighteen different regimes, and unifying the results from numerous earlier studies. A solution to a numerical overflow problem that arises in the computation of the transfer function is also found. All numerical code associated with this paper is distributed freely for use by the community.

This study assesses the performance of the Weather Research and Forecasting (WRF) model using a high-resolution spatial grid (1 km) with various combinations of physical parameterization packages to simulate a severe event in August 2021 in the southeastern Brazilian coast. After determining the optimal set of physical parameterizations for representing wind patterns during this event, a year-long evaluation was conducted, covering forecast horizons of 24, 48, and 72 hours. The simulation results were compared with observational wind data from four weather stations. The findings highlight variations in the efficacy of different physical parameterization sets, with certain sets encountering challenges in accurately depicting the peak of the severe event. The most favorable results were achieved using a combination of Tiedtke (cumulus), Thompson (microphysics), TKE (boundary layer), Monin-Obukhov (surface layer), Unified-NOAH (land surface), and RRTMG (shortwave and longwave radiation). Over the one-year forecasting period, the WRF model effectively represented the overall wind pattern, including forecasts up to three days in advance (72-hour forecast horizon). Generally, the statistical metrics indicate robust model performance, even for the 72-hour forecast horizon, with correlation coefficients consistently exceeding 0.60 at all analyzed points. While the model proficiently captured wind distribution, it tended to overestimate northeast wind speed and gust intensities. Notably, forecast accuracy decreased as stations approached the ocean, exemplified by the ATPM station.

The paper presents modelling of relationships between wind velocity distributions observed in Poland and technical requirements for wind power stations design. The wind velocities distributions for various locations in Poland are determined, and expressed in Weibull distribution parameters. Theoretical computations concerning the dependence of wind power station as function of wind speed and aire physical properties are presented. Conclusions important for design of power stations fitted to atmospheric conditions in Poland are given. Wind power plants have been an important source of electricity generation for many years.Wind power modelling with the use of wind speed is used to improve the accuracy of forecasts and analyses of the power production of wind farms.

To increase the power density of the electromechanical drive train of wind turbines, journal bearings can be used as planetary gear bearings instead of rolling bearings. This technological change presents new challenges. For example, wind turbine drive systems are subject to dynamic and low-speed operating conditions which can lead to an accelerated abrasive wear of the journal bearings. In addition, oil supply failure or peak loads due to wind gusts and grid and power converter faults could potentially result in catastrophic failure due to adhesive wear in a very short time. Such operating characteristics are, therefore, critical regarding the journal bearing wear lifetime and must be considered in the design. The successful implementation of journal bearings in wind turbines depends on a reliable estimation of adhesive and abrasive wear. In this paper, five different models for the wear calculation of journal bearings are evaluated regarding their suitability of wear calculation of planetary gear bearings in wind turbines. For this purpose, the following evaluation criteria were defined: parameter uncertainty, parametrization effort, in particular number of parameters, parameterization method and load case dependency of parameters and calculation effort. In order to be able to evaluate the wear models, the wear models are numerically implemented and the wear of a test journal bearing is exemplarily calculated under load conditions, which are comparable to load conditions in a wind turbine. Relevant influences from the wind turbine system such as lubricant, material and manufacturing dependent surface influences like roughness and hardness are considered. The wear models are evaluated with respect to their fulfillment of the defined criteria. The resulting evaluation allows the selection of a wear model that can be used to calculate the wear of planetary gear journal bearings in wind turbines, considering the available input variables.

Wind energy is one of the most attractive renewable energy sources because of its low operating, maintenance, and production costs as well as its low environmental impact. The goal of this study is to discover the best locations in Bangladesh where wind farms can be built and operated efficiently. This study applied the GIS and AHP methodologies to examine the eight important parameters upon which the suitability of locations is highly dependent. This analysis finds that Bangladesh has large regions appropriate for wind farm installation, with 3718.76 km² and 16631.14 km² classified as "very high" and "high" suitability, respectively. It was also observed that wind speed, land slope, and elevation each had a height-weighted criterion of 32 %, 27 %, and 12 %, respectively, when picking suitable locations. However, the viability of this study in identifying suitable sites has been evaluated based on ROC and AUC techniques and found satisfactory as per AUC value. The knowledge gained from this study will help the sustainable and renewable energy development authority (SREDA), Bangladesh to expedite the renewable energy investment process and will ensure the great certainty. The findings of this research can be considered as baseline information in the wind energy sector.

This paper is concerned with bump-less transfer of parametrized disturbance observer based controller (DOBC) with Individual Pitch Control (IPC) strategy for full load operation of wind turbine. Aerodynamic cyclic loads are reduced by tuning multivariable DOBC with the objective to reduce output power fluctuation, tower oscillation and drive-train torsion. Furthermore tower shadow and wind shear effect are also mitigated using parametrized controller. A scheduling mechanism between two DOBC is developed and tested on Fatigue, Aerodynamics, Structures, and Turbulence ( FAST) code model of National Renewable Energy Laboratory (NREL)’s 5 MW wind turbine. The closed-loop system performance is assessed by comparing the simulation results of proposed controller with a fixed gain and Linear Parameter Varying (LPV) DOBC with Collective Pitch Control (CPC) for full load operation. It is tested with step changing wind to see the behavior of the system under step change with wind shear and tower shadow (cyclic load) effects. Also turbulent wind is applied to see the smooth transition of the controllers. It can be concluded from the results that the proposed parametrized control DOBC with IPC shows smooth transition from one controller to another by interpolation. Moreover fatigue of the gear and tower due to wind shear and tower shadow effects are reduced considerably by the proposed controller as compared to collective pitch control.

Urban wind energy has emerged as an attractive source of distributed generation in cities to achieve sustainable development goals. The advance in technologies for the use of urban wind energy has turned this source into an attractive alternative for the decarbonization of cities and the energy transition. The objectives of this work are (1) to identify the potential of wind energy through numerical weather prediction (NWP) data tools and (2) to identify the roles and responsibilities of the stakeholders involved in the decision-making process. A methodology was developed in two phases and applied to a case study in the Dominican Republic. The first phase consisted of estimating the wind energy potential for the 32 provinces at a height of 10 m using open-access geographic reference systems tools provided by NASA. In the second phase, 28 stakeholders were identified through snowball sampling. The Responsible, Accountable, Consult, and Informed (RACI) matrix tool was applied to identify the roles of the 28 institutions addressed at the country level as relevant in the decision-making process for the energy sector. The annual average wind speed and energy potential for each province were determined. It was found 24 provinces have poor potential, below <4.5 m/s. In the northwest and east is where there is the greatest potential, between 4.83 - 6.63 m/s. The population density was established and was observed that the provinces with greater potential are less densely populated. Through 59 interviews 28 institutions were identified and evaluated due to their relevance in decision-making for the implementation of energy projects. The MEM has strongly categorized as “A”, electricity distribution companies as “R”, energy associations and universities as “C”, and educational and justice institutions as “I”.

Timely detection of surface damages on wind turbine blades is imperative for minimising downtime and avoiding possible catastrophic structural failures. With recent advances in drone technology, a large number of high-resolution images of wind turbines are routinely acquired and subsequently analysed by experts to identify imminent damages. Automated analysis of these inspection images with the help of machine learning algorithms can reduce the inspection cost, thereby reducing the overall maintenance cost arising from the manual labour involved. In this work, we develop a deep learning based automated damage suggestion system for subsequent analysis of drone inspection images. Experimental results demonstrate that the proposed approach could achieve almost human level precision in terms of suggested damage location and types on wind turbine blades. We further demonstrate that for relatively small training sets advanced data augmentation during deep learning training can better generalise the trained model providing a significant gain in precision.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Background: We studied Riveaux Road Fire, which was ignited by multiple lightning strikes in January 2019 and burnt more than 637.19 km² in southern Tasmania, Australia. Aims: We focused on fire weather, such as identification of dynamic wind and vegetation type, in a valley of the study area. Methods: We employed two methods: numerical weather model vertical sounding (NWMVS) and the use of a fire simulator, to quantify and examine the contribution of dynamic winds to fire behaviour. The NWMVSs allow rapid diagnosis of changes in wind, temperature, dew point temperature and cloud coverage. Prototype 2 is a fire simulator based on the specification of Australian Fire Danger Rating System (AFDRS). Key results: We found fires to be guided by terrain-forced channelling primarily and by downslope wind conditionally in the valleys. In addition, the fire intensity periodically changed with the magnitude of surface wind, in buttongrass moorland, in which the fire often smoulders, during the fire period according to the satellite image. Conclusions and Implications: Therefore, there should be caution for not only terrain and dynamic wind but also vegetation type during fire spread in rugged terrain.

This work utilizes the particle swarm optimization (PSO) for the optimal sizing of a solar – wind – battery hybrid renewable energy system (HRES) for a rural community in Rivers State, Nigeria (Okorobo-Ile Town). The objective is to minimize the total economic cost (TEC), the total annual system cost (TAC) and the levelized cost of energy (LCOE). A two – step approach is used. The algorithm first determines the optimal number of solar panels and wind turbines. Based on the results obtained in the first step, the optimal number of batteries and inverters is computed. The overall results obtained is then compared with results from the NGSA-II and hybrid GA – PSO optimization algorithm. An energy management system monitors the energy balance and ensures the load management is adequate using the battery state of charge as a control strategy. Results obtained showed that the optimal configuration consist of solar panels (154), wind turbine (3), inverter (136) and batteries (29). This results in a minimized TEC, TAC and LCOE of 476, 731USD, 301, 947USD and 0.011USD/kWh respectively. The optimal configuration when simulated under various climatic scenarios was able to meet the energy needs of the community irrespective of ambient condition.

In recent decades the Mediterranean area observed an increase in large fires, despite the decrease in the number of fire ignitions, following a worldwide tendency. Climate change has been the main culprit for large burnt areas, and alterations of forest ecosystems, resulting in the increased recurrence of forest fires. In Portugal, the analogous trend resulted in the destruction of large rural, urban and industrial areas, where after the 2017 months of June and October catastrophic events, the government implemented the 2019 specific policies for preventing fire outbreaks and defending the forest against fires. This compulsory policy demanded that landowners and local governments alike needed to contact specific authorities requesting authorization for their intentions to clean properties in and around urban areas, roads, and forest limits. Despite policy and careful monitoring, ignitions still occur, and in many cases resulting from the implementation of such policies. The study analyses the before and after policy implementation, considering 6904 ignitions records from the period between 2014 and 2023 from the central area of Portugal, covering the transition area between the agricultural fields of the Tagus valley and the Monte-junto-Estrela Mountain range, the district of Santarém. The authorization to use fire in clearance practices is granted according to a set of weather conditions, temperature, wind intensity, and relative humidity, when analyzing fire ignitions with the average daily wind intensity at the site of the occurrence, we observed that more than half of wildfires occur on days with winds between 10 and 20 Km/h, whereas intensities greater than 30 Km/h only 1% of the total occurrences, and of these 22% occurred due to the use of fire in the burning of agricultural leftovers and cut and piled bushes. The circulation of the thermal depression in the Iberian Peninsula gives rise to increasing intensity throughout the day, reaching a maximum in the late afternoon, this factor combined with the misjudgment of safe conditions leads us to suggest stricter intervals and the need for awareness of daily variation in conditions.

Hong Kong was under the direct hit of Severe Typhoon Koinu (2314) on 8 and 9 October 2023, necessitating the issuance of the Increasing Gale or Storm Signal, No. 9. Koinu was a very challenging case for TC forecasting and warning services due to its compact size and erratic movement over the northern part of the South China Sea. This paper reviews the difficulties and challenges on the forecasting aspect of the severe typhoon. The predicted tropical cyclone track and intensity from both conventional models and emerging artificial intelligence models are examined, as well as local wind and rainfall forecast. Experience in this case study showed that while deterministic global models only performed moderately and were not able to adequately support early warning, a regional model and AI models could more effectively support decision making for operational tropical cyclone warning service.

Hong Kong was under strike from Super Typhoon Saola (2309), necessitating the issuance of the highest tropical cyclone warning signal. Saola skirted past the south-southwest of Hong Kong, bringing hurricane force winds and significant storm surge. Saola had its closest approach to Hong Kong on 1 September 2023, posing a unique challenge in forecasting and early warning for the commencement date of the new school term, where higher impact to traffic and public safety was anticipated. This paper covers the challenges on the forecasting aspect of the super typhoon. The predicted tropical cyclone track, intensity and wind structure are reviewed. Experience in this case showed that while there was not a perfect numerical weather prediction model in terms of the forecast track, intensity and wind structure of Saola, multi-model approach provided very use-ful and crucial information for operational weather warning services.

In the present work, the main methodologies used to reconstruct wind fields in the U-SPACE have been analyzed. The SESAR U-SPACE program aims to develop an Unmanned Traffic Management system with a progressive introduction of procedures and services designed to support a secure access to the air space for a large number of drones. The Italian Aerospace Research Center (CIRA) is carrying out the EDUS project focused on the development and validation of operating platform demonstrators serving the micro-scale weather forecasts and the collection of information necessary for the definition of the flight plan of the drones in urban contexts. For this reason, the state of art methodologies that can be used to estimate winds at low altitudes in urban areas starting from available observational data have been reviewed in the present paper. Some of these techniques were originally developed for reconstruction at high altitudes, but successively adapted to treat different heights. A common approach to all techniques is to approximate the probabilistic distribution of wind speed over time with some parametric models, apply spatial interpolation to the parameters and then read the predicted value.

The growing need to use renewable sources and the current difficulty in spreading the electricity grid in a widespread manner raise the question of how to respond to the need for more electricity immediately. The idea behind this study is to power a horizontal axis wind turbine with the air flow generated for cooling a stationary internal combustion engine. The power extracted from this solution is significantly lower than that of the internal combustion engine (about 0.3%) and could be advantageous only in limited contexts. Installation costs are limited because many elements deriving from wind variability can be removed or simplified.

An economic and business history approach is used to show the rise and relative failure of the Spanish wind industry during the period between 2004-2015, when Spain became the fourth country after China, the US and Germany in installed capacity of renewable energies and, in relative terms, the second country after Denmark. This study is unique in that it provides an integrated vision of the reasons for the relative fall of Spain in the world ranking of wind energy producers. The methodology of the economic analysis of industrial policies makes it possible to explain the fall in the relative importance of Spain in the international panorama of wind farms. There were no reasons related to technological obsolescence or inability of the CECRE managing renewable energies to explain the fall.

On 2013 the Villonaco wind farm (16.5 MW), the first wind farm in continental Ecuador near the city of Loja, began operations. The power generated is delivered to the National Interconnected System (SNI), which services the city. This research confronts two sets of real data, the electricity use of the urban area of Loja, and the power generated by the Villonaco Wind Farm. Electricity use follows clearly defined daily and weekly cycles, and wind power has a seasonal behaviour. The study shows that wind power integration cannot be a long-term stable power source regardless power or generation surplus. Another essential finding is that time series can be used as a statistical source to determine the need for short- (seconds) and long- (days, weeks) term energy storage. Strategies to further the energy autonomy of the urban area through the expansion of the wind farm by a factor of 2 are discussed.

The present studies deliver the computational investigations of a 10 MW turbine with a diameter of 205.8 m developed within the framework of the AVATAR (Advanced Aerodynamic Tools for Large Rotors) project. The simulations were carried out using two methods with different fidelity levels, namely the computational fluid dynamics (CFD) and blade element and momentum (BEM) approaches. For this purpose, a new BEM code namely B-GO was developed employing several correction terms and three different polar and spatial interpolation options. Several flow conditions were considered in the simulations, ranging from the design condition to the off-design condition where massive flow separation takes place, challenging the validity of the BEM approach. An excellent agreement is obtained between the BEM computations and the 3D CFD results for all blade regions, even when massive flow separation occurs on the blade inboard area. The results demonstrate that the selection of the polar data can influence the accuracy of the BEM results significantly, where the 3D polar datasets extracted from the CFD simulations are considered the best. The BEM prediction depends on the interpolation order and the blade segment discretization.

The predictability of wind information in a given location is essential for the evaluation of a wind power project. Predicting wind speed accurately improves the planning of wind power generation, reducing costs and improving the use of resources. This paper seeks to predict the mean hourly wind speed in anemometric towers (at a height of 50 meters) at two locations: a coastal region and one with complex terrain characteristics. To this end, the Holt-Winters (HW), Artificial Neural Networks (ANN) and Hybrid time-series models were used. Observational data evaluated by the Modern-Era Retrospective analysis for Research and Applications-Version 2 (MERRA-2) reanalysis at the same height of the towers. The results show that the hybrid model had a better performance in relation to the others, including when compared to the evaluation with MERRA-2. For example, in terms of statistical residuals, RMSE and MAE were 0.91 and 0.62 m/s, respectively. As such, the hybrid models are a good method to forecast wind speed data for wind generation.

Vertical wind speed extrapolation is a commonly used method that involves estimating wind speeds at various heights based on measurements taken at a specific height. In this study, we compared the short-and long-term extrapolation methods of wind parameters using data collected on site by anemometers at two different heights. We assessed the accuracy of these methods by calculating the statistical indicators for performance evaluation, and then determined the most appropriate model for the two types of vertical extrapolation. Additionally, we evaluated energy potential characteristics, as well as the statistical analysis of wind speed distribution and wind power density based on the Weibull and Rayleigh distribution. Our results indicated that the power law is the most suitable model for the short-term method, while the modified Mikhail model is the most appropriate for long-term extrapolation. We also found that the wind potential of this area is favorable for wind turbine integration.

The tension cable-supported power transmission structure (TC-PTS) is a new type of power transmission structure suitable for mountainous terrain, which is sensitive to wind load. In this regard, a nonlinear finite element analysis model of wind-induced vibration is proposed for the TC-PTS, and the wind-induced vibration response of the structure is analyzed. Firstly, the tangent stiffness matrix of the three-dimensional truss element for the supporting suspension cable and transmission line, considering the geometric nonlinearity of structures, is derived through the relationship between the element elastic energy and its displacement. Subsequently, the element mass matrix and damping matrix of the supporting suspension cable and transmission line, as well as the element nodal load vector obtained from wind load equivalence are given. Then, based on the nonlinear finite element theory, the nonlinear dynamic equation of wind-induced vibration is established for the TC-PTS and solved by Newmark-β method combined with Newton-Raphson iterative method. Furthermore, the rain-flow counting method and Miner's linear fatigue cumulative damage theory were used for wind induced fatigue damage assessment. Finally, a two-span TC-PTS is selected as an example, and the wind-induced nonlinear vibration and fatigue damage assessment are analyzed through the proposed model. The results show that the proposed model has high computational accuracy and efficiency. With the increase of wind speed and wind direction angle, the maximum lateral displacement and tension of the supporting suspension cable and transmission line increase, and their degree of increase shows a nonlinear trend. In terms of the wind-induced fatigue analysis results of TC-PTS, the fatigue damage at the end of the supporting-conductor suspension cable is greater than the fatigue damage at its midpoint. Compared to the fatigue damage at the midpoint of the conductor, the fatigue damage at the end of the conductor is less affected by wind direction angle, and both are more significantly affected by the wind speed.

Floating Offshore Wind Turbine (FOWT) is an innovative technology with little industry guidance for its hull design. Various FOWT floaters with different hull shapes claim to support the same turbines. Structural integrity and material expense analyses of different pontoon shapes were conducted, and it was found that some configurations, such as those with every two columns connected by both pontoon and bracing, have advantages over others. However, it is important to note that the choice of pontoon shape should be based on the wave loading conditions the floater will be exposed to. While a T-shaped pontoon provides a cost-effective solution under certain wave loading scenarios, it may not be the best option for all conditions. Specifically, ring pontoon designs with full bracing were found to be necessary for withstanding certain wave loads. Therefore, it is important to consider different Dominant Load Parameters (DLP) and ensure that a FOWT floater can withstand all applicable DLPs. An uneven hexahedral column shape, which combines the best attributes of square and round shapes, is proposed as a better alternative to cylindrical columns. It offers ease of manufacture and reasonably low drag. Bracing is found to be necessary for withstanding the wind turbine’s incurred moment and forces. The conclusion is that platform design should prioritize manufacturing costs and strength over maximizing hydrodynamic performance.

In the context of energy decarbonization, wind farms with type IV wind turbines from various manufacturers are being massively put into operation. These wind turbines comply with the requirements of the grid codes of the countries where they are designed and/or manufactured, but do not factor in the specific features of the distribution networks of other countries to which they are connected. The study at issue involves a comparative analysis of the requirements of grid codes of different countries for the stable operation of wind turbines under standard disturbances. The Low Voltage Ride Through (LVRT) characteristic implemented in type IV wind turbine inverters makes it possible to prevent wind turbine shutdowns in case of short-term voltage dips of a given depth and duration. The calculations of transient processes indicate that wind turbines may not meet the requirements of the grid code of a particular country for their stable operation. As a result, standard disturbances will block the reactive current injection and the wind turbine will be switched off. This is often caused by the relay protection devices with a time delay of 1-2 s, which are used in distribution networks and implement the functions of long-range redundancy. Excessive shutdowns of wind turbines lead to emergency rise in the load for the generating units of conventional power plants, aggravating the post-accident conditions and disconnecting consumers of electricity. The paper presents a method for checking the LVRT characteristic settings for compliance with the technical requirements for wind turbines. To prevent wind turbine outages, one should either change the configuration of the LVRT characteristic, or upgrade the relay protection devices in the distribution network adjacent to the wind farm, or implement group or individual technical solutions at the wind farm. The performance of the proposed technical solutions is confirmed by the calculations of transient processes.

In April 2019, a team of Keio University and Bucknell University students was assembled to participate in Ericsson Innovation Awards with a novel concept for generating renewable energy. This conceptual system consists of a vertical axis wind turbine, a crossflow marine hydrokinetic turbine, a floating platform integrated with a quadcopter system, and three to four temporary mooring lines with ship-type anchors. The proposed designed aims to offer solutions to two current problems of floating offshore wind energy: high construction cost of floating platforms and difficulties in maintenance of mooring lines. The combination of two vertical-axis turbines into a single floating platform would enable the system, namely ESwift, to extract energy from both wind and current resources. Additionally, due to the utilization of vertical axis turbines, the center of gravity of the proposed concept is significantly lower with respect to water level, compared to that of existing floating horizontal axis wind turbines, which would potentially reduce the floater's size and construction cost. Lastly, the integrated quadcopter mechanism would assist the floater in terms of stability and mobility, and enables an array of ESwifts to automatically rearrange for maximal energy generation. The authors hope that readers would find the idea described in this open access letter worth pursuing and would further develop and commercialize the ESwift concept.

Purpose – Extend the Blade Element Momentum Theory (BEMT) such that rotors with pronounced cone and axis angle (tilt or yaw) can be calculated. Derive an equation for the speed ratio (lambda) as a function of Tip Speed Ratio (TSR), radius, blade, cone and axis angle. This converts the BEMT into an Unsteady BEMT or UBEMT. Present the Wagner rotor as one such rotor geometry. --- Methodology – Literature review and calculations. --- Findings – The UBEMT can be used to calculate highly unconventional rotor geometries. --- Research Limitations – Although the aerodynamic coefficients used in the UBEMT are from measurements in steady flow conditions, they can be used with success. --- Practical Implications – Also conventional Horizontal Axis Wind Turbines (HAWT) with noticeable cone and axis angle should be calculated with the UBEMT. The accuracy of power calculations of these HAWTs can be slightly improved. --- Originality – Analytic equations for rotors with cone and axis angle have barely been discussed.

The Doubly-Fed Induction Generator (DFIG) has significant features in comparison with Fixed Speed Wind Turbine (FSWT), which has popularized its application in power system. Due to partial rated back-to-back converters in the DFIG, Fault Ride-Through (FRT) capability improvement is one of the great subjects regarding new grid code requirements. To enhance the FRT capability of the DFIG, many studies have been carried out. Fault current limiting devices as one of the techniques are utilized to limit the current level and protect switches of the back-to-back converter from over-current damage. In this paper, a review is done based on fault current limiting characteristic of the proposed fault current limiting devices Therefore, Fault Current Limiters (FCLs) and Series Dynamic Braking Resistors (SDBRs) are mainly taken into account. Operation of all configurations including their advantages and disadvantages is explained. Impedance type and the fault current limiting devices’ location are two important factors, which significantly affect the DFIG behaviour in the fault condition. These two factors are basically studied by the simulation and their effects on the key parameters of the DFIG are investigated. Finally, future works in respect to the FCL application in the FRT improvement of the DFIG have also been discussed.

Full-scale/model test comparison studies to validate the traditional ABL wind tunnel simulation technique are reviewed. According to the literature review, notable discrepancies between full-scale measurement results and model test results were observed by most performed comparison studies, but the causes of the observed discrepancies were not revealed in a scientific way by those studies. In this regard, a new research scheme for future full-scale/model test comparison studies is proposed in this article, which utilizes the multiple-fan actively controlled wind tunnel simulation technique. With the new research scheme, future full-scale/model test comparison studies are expected to reasonably disclose the main problems with the traditional ABL wind tunnel simulation technique, and the technique can be improved correspondingly.

The energy sector relies on numerical model output forecasts for operational purposes on a short-term scale, up to 10 days ahead. Reducing model errors is crucial, particularly given that coarse resolution models often fail to account for complex topography, such as that found in Costa Rica. Local circulations affect wind conditions at the level of wind turbines, thereby impacting wind energy production. This work addresses a specific need of the Costa Rican Institute of Electricity (ICE) as a public service provider for the energy sector. The developed and implemented product in this study serves as a proof of concept that could be replicated by WMO Members. It demonstrates a product for wind speed forecasting at wind power plants by employing a novel strategy for input selection based on large-scale indicators to enhance Artificial Intelligence-based forecasting methods. The product is developed and implemented based on the full-value chain framework for weather, water, and climate services for the energy sector introduced by the WMO. The results indicate a reduction of wind forecast RMSE by approximately 55% compared to the GFS grid values. The conclusion is that combining coarse model outputs with regional climatological knowledge through AI-based downscaling models is an effective approach for obtaining reliable local short-term wind forecasts up to 10 days ahead.

The energy transition to wind and solar opens opportunities for green hydrogen as the wind and solar generation tends to bring electricity prices down to very low levels. This paper evaluates whether green hydrogen can integrate well with wind and solar PV to help with improved management of the South Australian electricity grid. Green hydrogen can use membrane electrolysis plants during surplus renewable energy periods. This hydrogen can then be electrified or used in industry. The green hydrogen system was analysed to understand the financial viability and technical impact of integrating green hydrogen. We also used systems engineering techniques to understand the system holistically, including the technical, social, environmental, and economic impacts. The results show opportunities for the system to provide seasonal storage, grid firming, and reliability services. Financially, it would need changes to electricity rules to be viable, but without those changes, our modelling suggested it would be financially viable within this decade

In the present work, a methodology for wind field reconstruction based on the Meteo Particle Model (MPM) from Numerical Weather Prediction (NWP) data is presented. The development of specific wind forecast services is a challenging research topic, in particular for what concerns the availability of accurate local weather forecasts in highly populated areas. Currently, even if NWP Limited Area Models (LAMs) are run at spatial resolution of about 1 km, this level of information is not sufficient for many applications, for example to support drone operation in urban contexts. The coupling of MPM with the NWP Limited Area Model COSMO has been implemented in such a way that the MPM reads the NWP output over a selected area and provides wind values in the generical point considered for the investigation. The numerical results obtained reveal a good behavior of the method in reproducing the general trend of wind speed, as confirmed also by the power spectra analysis. The MPM is able to step over the intrinsic limitations of the NWP model in terms of spatial and temporal resolution even if the MPM inherits the bias that inevitably affects the COSMO output.

This paper performs a comprehensive analysis of the wind energy potential of onshore regions in Greece with emphasis on quantifying the volume risk and the spatial covariance structure. Optimization techniques are employed to derive efficient wind capacity allocation plans (also known as generation portfolios) incorporating different yield aspirations. The generation profile of minimum variance and other optimal portfolios along the efficient frontier are subject to rigorous evaluation using a fusion of descriptive and statistical methods. In particular, principal component analysis is employed to estimate factor models and investigate the spatiotemporal properties of wind power generation, providing valuable insights into the persistence of volume risk. The overarching goal of the study is to employ a set of statistical and mathematical programming tools guiding investors, aggregators and policy makers in their selection of wind energy generating assets. The findings of this research challenge the effectiveness of current policies and industry practices, offering a new perspective on wind energy harvesting with a focus on the management of volume risk.

Extensive surface and upper air measurements of a typhoon over the northern part of the South China Sea, namely, Typhoon Talim in July 2023, are documented and analyzed in this paper. A number of features have been observed from the upper air measurements. First, the log law and the power law are found to be appropriate in fitting the wind profiles of the typhoon in the first 1000 m or so above the sea surface. A low level jet is observed in the lower troposphere from the observations of the radar wind profilers. The paper is also novel from the perspectives that the vertical wind profile from a Doppler LIDAR on an offshore platform over the northern part of the South China sea, and that ocean radar data are used to analyze the surface wind observations of a typhoon in the region. The results of this paper would be useful in understanding the structure of tropical cyclones, e.g. in wind engineering applications.

Currently, there are different types of technology for the production of electricity that use various energy sources, this causes the establishment of generation centers that provide from a small amount to tens of megawatts of electrical energy. These centers are built to supply electricity to nearby loads through networks integrated into a large electrical system or in isolation with their electrical system. The technological evolution, the different energy sources, and the generation centers close to the consumers entail what has been called a distributed generation (DG), the DG carries with it aspects that need to be analyzed. In this paper, the impact of wind generation on the medium voltage energy distribution network is studied, it was determined that the addition to the distribution network of power by wind turbines less than the transmission center does not produce an impact on the network. Simulated results obtained using SIMULINK and DIgSILENT are presented and discussed.

This work compared the performance of three methods for constructing a regional ensemble prediction system (EPS) for wind speed forecasts: dynamical downscaling, breeding of growth modes (BGM), and blending method. The Weather Research and Forecasting (WRF) model was used to downscale the European Centre for Medium-range Weather Forecast (ECMWF) EPS. In addition, as the BGM method needs observation data for generating scaling factors, an alternative method for generating scaling factors was proposed to eliminate dependence on observation data. One-month tests between October 1st and October 30th, 2020, were implemented to evaluate the performance of three methods in the Gansu province of China. The results demonstrate that the blending method outperforms the other two methods. Furthermore, the difference in performance is evident mainly in early forecast lead time and becomes negligible as forecast time increases.

SStatistical characteristics of the wind speed in Samaria region of Israel have been analyzed by processing 11 years of wind data provided by the Israeli Meteorological Service, recorded at 10 m height above the ground. The cumulative mean wind speed at measurement height was shown to be 4.53 m/s with standard deviation of 2.32 m/s. Prevailing wind direction is shown to be char-acterized by cumulative mean azimuth of 226° with standard deviation of 79.76°. The results were extrapolated to 70-meter height in order to estimate wind characteristics at hub height of a me-dium-scale wind turbine. Moreover, Weibull distribution parameters were calculated annually, monthly and seasonally, demonstrating a good match with histogram-based statistical repre-sentations. Shape parameter of the Weibull distribution was shown to reside within a narrow range of 1.93 to 2.15, allowing us to assume a Rayleigh distribution, thus simplifying wind tur-bines energy yield calculations. The novelty of the current paper is related to gathering wind statistics for a certain area (Samaria) we are not aware of any published statistics regarding wind velocity and direction in this area. The data may be interesting for potential regional wind energy development in which the obtained Weibull distribution can be used in calculations of expected power generation of particular turbines with known power dependence on velocity. We also point out that the fact that realistic wind velocity statistics is well described by an analytic formula (Weibull distribution) is not trivial, and in fact the fit may have been poor.

This study examines the effect of surface currents on the bulk algorithm calculation of wind stress estimated using the scatterometer data during 2007-2020 in the Indian Ocean. In the study region as a whole the wind stress decreased by 5.4% by including currents into the wind stress equation. The most significant reduction in the wind stress is found along the most energetic regions with strong currents such as Somali Current, Equatorial Jets and Aghulhas retroflection. A highest reduction of 11.5% is observed along the equator where the Equatorial Jets prevail. A sensitivity analysis has been carried out for the study region and for different seasons to assess the relative impact of winds and currents in the estimation of wind stress by changing the winds while keeping the currents constants and vice versa. The inclusion of currents decreased the wind stress and this decrease is prominent when the currents are stronger. This study showed that equatorial Indian Ocean is the most sensitive region where the current can impact on wind stress estimation. The results showed that uncertainties in the wind stress estimations are quite large at regional levels and hence better representation of wind stress incorporating ocean currents should be considered in the ocean/climatic models for accurate air-sea interaction studies.

The limitedness of the nonrenewable local energy resources in Israel, even in background of the later gas fields’ findings, continues to force the state to devote various efforts for the ‘green’ energy development. These efforts include installations both in the solar and in the wind energy, with a purpose to improve the diversity of energy sources. While the standard discounted cash flow (DCF) method using the net present value (NPV) criterion is extensively adopted to evaluate investments, the standard DCF method is inappropriate for the rapidly changing investment climate and for the managerial flexibility in investment decisions. In recent years, the real options analysis (ROA) technique is widely applied in many studies for valuation of renewable energy investment projects. Hence, we apply in this study the real options analysis approach for the valuation of wind energy turbines and apply it to the analysis of wind energy economic potential in Israel.

Integration of wind energy into the grid faces a great challenge regarding power quality. The International Electrotechnical Commission (IEC)~61400-21 standard defines the electrical characteristics that need to be assessed in a Wind Turbine (WT), as well as the procedure to measure the disturbances produced by the WT. One of the parameters to be assessed are voltage fluctuations or flicker. To estimate the flicker emission of a Wind Power Plant (WPP), the standard establishes that a quadratic exponent should be used in the summation of the flicker emission of each WT. This exponent was selected based on studies carried out in WPPs with type I and II WTs. Advances in wind turbines technology have reduced their flicker emission, mainly thaks to the implementation of power electronics for the partial or total management of the power injected into the grid. This work is based on measurements from a WPP with 16 type III WTs. The flicker emission of a single WT and of the WPP were calculated. Low flicker emission values at the Point of Common Coupling (PCC) of the WPP were obtained. The flicker estimation at the PCC, based on the measurement from a single WT, was analyzed using different exponents. The results show that a cubic summation performs better than the quadratic one in the estimation of the flicker emission of a WPP with type III WTs.

The paper deals with the problem of choosing the best O&M strategy for wind power plants. Current maintenance theory considers just production opportunities and minimizes the maintenance costs, but with the liberalization of the electricity market also the electricity price has become an important variable to take into account in the O&M scheduling. Another important variables that is often neglected by the existing maintenance theory is the weather condition. This paper proposes a new strategy that takes into account the electricity price and weather conditions, improves the expected profit of the systems, and reduce the overall maintenance and logistic costs. The maintenance schedule is formalized as an optimization problem where the discounted cumulative profit of a wind generation portfolio in a fixed-time horizon (e.g. two years ahead), subject to the technologically-derived maintenance time constraints is optimized. Both the theoretical and computational aspects of the proposed O&M strategy are discussed. Results show that taking into account market and weather opportunities in the design of the maintenance strategy, it is possible to achieve a more complete scheduling for a given set of wind power plants.

This article presents a study conducted within a wind tunnel to enhance understanding of the excitation mechanism of stay cable vibration under arid conditions. Numerous wind tunnel tests were meticulously analyzed. Initially, the vibration of the stay cable was measured under steady flow conditions at a flow angle of 45 degrees and an inclination of 25 degrees, while varying wind velocities were applied. Additionally, an investigation into the flow field surrounding the stay cable was conducted in both vertical and horizontal directions. By utilizing two hot wire anemometers in the cable wake, an extensive database of flow field measurements was obtained. The experimental results revealed that the vibration characteristics of the stay cable under the arid conditions considered in this study aligned with findings reported in existing literature. Notably, a deeper comprehension of the excitation mechanism of a stay cable in a dry state was attained. This mechanism is closely associated with the inhibition of Karman vortices and the development of low-frequency vortices. At low wind speeds, Karman vortices predominated, resulting in small-amplitude vibrations. However, as the wind speed increased, the influence of Karman vortices diminished progressively, while the low-frequency vortices grew stronger. These low-frequency vortices exhibited high energy and a significant correlation with shedding along the stay cable, thereby inducing cable vibration in a dry environment.

The survey findings reveal that rivers worldwide carry an annual sediment load of 15 billion tons into the sea, and the Yellow River basin alone contributes 1.6 billion tons of sand. Therefore, understanding the science of wind and sand in the Yellow River is crucial to ensuring the safe development of similar basins across China and the world. This study examines the midstream wind and sand area of the Xiliugou tributary, a part of the upper Yellow River. The researchers used a stepped sand collector combined with an anemometer to measure the sand transport flux at 0-50 cm height on various underlying surfaces of the basin. Then, they estimated the amount of wind and sand entering the Yellow River using a function model based on the measured factors. Furthermore, the team analyzed the particle size composition of wind-eroded sand to better understand the principles of wind and sand erosion and accumulation in the basin. The results of the study show that the sand transport flux per unit area varies significantly across different underlying surfaces. Moreover, the contribution of moving sandy land, semi-fixed sand, and fixed sand to wind and sand deposition in the Yellow River basin was 77.08%, 15.30%, and 7.62%, respectively. The vertical change of sand transport rate on the basin's surface demonstrates that the total sand transport rate is an exponential function of wind speed. Based on this relationship, the researchers estimated that the total annual average wind and sand entering the Yellow River basin via the Xiliugou tributary is approximately 8.09×105t. Due to the basin's unique geography and sand source, the particle size composition of wind-eroded sand differs between the east and west sides of the river channel. On the west side, desert sand, mainly fine sand, and very fine sand constitutes the sand source. Conversely, on the east side, sand collected in the riverbed by secondary wind erosion is the primary sand source. Furthermore, human activities have disturbed the grain composition, mainly comprising powder and clay particles. This phenomenon, known as "wind-blown mud and water-washed sand," is evident in this geographical unit. In conclusion, the Yellow River basin still faces significant ecological security hazards. Understanding the coupling relationship between desert-basin-sand and wind is the foundation for effectively controlling wind and sand flow into the Yellow River basin.

With the rapid development of global offshore wind power, the demand for offshore wind power operation and maintenance is also increasing. Wisdomization of offshore wind farms is a practical need to improve the operation level and benefit of offshore wind farms. This paper first introduces the current development situation and characteristics of global offshore wind power, and expounds the current situation and main challenges of offshore wind power operation and maintenance market. Therefore, our paper discusses the innovation of offshore wind power operation and maintenance from the aspects of operation and maintenance management of offshore wind power, monitoring and analysis technology of units, far-reaching wind field monitoring and operation and maintenance risks. Then, combined with information technology and lean management concept, a smart operation and maintenance management platform for wind farms in far-reaching sea areas is built to explore centralized and intelligent operation and maintenance management mode, improve operation and maintenance efficiency of wind farms in far-reaching sea areas, and minimize operation and maintenance costs. Finally, through the research on the characteristics of 5G technology, combined with the practical experience of operation and maintenance, and in view of the characteristics of offshore wind farms, we analyze and propose several typical application scenarios of 5G technology in the intelligent operation and maintenance of offshore wind farms, which provides a new solution for the efficient operation and maintenance of offshore wind farms.

In this paper, dual-rotor counter-rotating (CR) configurations of vertical axis wind turbines (VAWT) are briefly inspected and divided into three types. This investigation was focused on one of these types – the CR-VAWT with co-axial rotors, in which two equal rotors are placed on the same shaft, displaced from each other along it and rotate in opposite directions. For this CR-VAWT with three-blade H-Darrieus rotors, the properties of the design in terms of aerodynamics, mechanical transmission and electric generator, as well as control system are analyzed. A new direct-driven dual-rotor (DR) permanent magnet synchronous generator (PMSG) was proposed, in which two built-in low-power PM electric machines have been added. They perform two functions – start-up and overclocking of the rotors to the angular velocity at which the lifting force of the blades is generated and stabilizing the CR-VAWT work as wind gusts act on the two rotors. Detailed in this paper is the evaluation of aerodynamic performance of the CR-VAWT via 3D computational fluid dynamics (CFD) simulations. The evaluation was conducted using the CONVERGE CFD software with the inclusion of the actuator line model for the rotor aerodynamics, which significantly reduces the computational effort. Obtained results show that both rotors, while they rotate in opposite directions, had a positive impact on each other: the power coefficients of the upper and lower rotors in the CR-VAWT increased by 5.5% and 13.3% respectively compared to the single-rotor VAWT at the optimal distance between the rotors of 0.3 from a rotor height.

The prediction of wind power output is part of the basic work of power grid dispatching and energy distribution. At present, the output power prediction is mainly obtained by fitting and regressing the historical data. The medium- and long-term power prediction results exhibit large deviations due to the uncertainty of wind power generation. In order to meet the demand for accessing large-scale wind power into the electricity grid and to further improve the accuracy of short-term wind power prediction, it is necessary to develop models for accurate and precise short-term wind power prediction based on advanced algorithms for studying the output power of a wind power generation system. This paper summarizes the contribution of the current advanced wind power forecasting technology and delineates the key advantages and disadvantages of various wind power forecasting models. These models have different forecasting capabilities, update the weights of each model in real time, improve the comprehensive forecasting capability of the model, and have good application prospects in wind power generation forecasting. Furthermore, the case studies and examples in the literature for accurately predicting ultra-short-term and short-term wind power generation with uncertainty and randomness are reviewed and analyzed. Finally, we present prospects for future studies that can serve as useful directions for other researchers planning to conduct similar experiments and investigations.

Sudden variation of aerodynamic loads is the potential source of safety accidents of high-speed train (HST). As a follow-up investigation on the aerodynamic response of a HST that enters a tunnel under crosswind environment, this paper focuses on the transient response of a HST’s safety indices based on the train–track coupling interaction model. Firstly, a wind–train–track coupling dynamic model is proposed by introducing transient aerodynamic loads into the vehicle–track system. Secondly, the temporal evolution of safety coefficients indicates that the train’s safety risk increases during tunnel entry with crosswind. Results show that the derailment coefficients and wheel load reduction rate during tunnel entry are not only larger than those in open air but also those inside the tunnel due to the sudden disappearance of wind excitation at the tunnel entrance. In addition, the characteristic wind curve, which is the wind velocity against the train speed, is presented for application based on the current specification of the safety criteria threshold. The investigation will be useful in assessing the safety risk of a running train subjected to other aerodynamic attacks, such as the coupling effect of infrastructure scenario and crosswind in windy area.

Wind energy is one of the main drivers of the renewable energy market. The wind turbine gearbox, used as a multiplier - is one of the main components directly related to wind turbine efficiency and lifespan. Therefore, the strict control of the gearbox project and its manufacturing processes or even minor improvements in this component heavily and positively impact energy production/generation over time. This work diagnoses a 1.6 MW gearbox fracture mechanics to identify its main reason and how the chain of events took place, leading to the catastrophic failure. The diagnoses underwent numerical simulation (Finite Element Analysis - FEA) and further analysis of the lubrication system, bearings, planetary stage gears, helical stage gears, and high-speed shaft. In conclusion, although the numerical simulation showed high contact stresses between the teeth, the region with the crack nucleated was the top land (tip of the tooth). The most likely factors that led to the premature failure were the missed lubrication for the planetary bearings, lack of gear raw material cleanliness, and excessive case depth at the tip of the sun shaft gear teeth. With the sun gear, planet bearings, and planet gears broken in pieces, those small and large pieces dropped into the oil, between the gears, and into the tooth ring, ending up as a premature gearbox failure.

Presently, Jordan confronts a double substantial challenge of enhancing energy security and mitigating greenhouse gas emissions. One of the most encouraging avenues to attain the objectives of sustainable development, energy security, and environmental conservation is to enhance the integration of renewable energy into the generation of electricity. In pursuit of this goal, the Jordanian government intends to expand investments in the green energy sector, with solar and wind energy poised to play a key role in satisfying energy demands and cultivating an environmental sustainability. This paper aims to examine the distinctive dynamics, challenges, obstacles, and potential solutions corresponding to the establishment of community solar and wind farms in Jordan suburban areas. It aims to highlight the opportunities and barriers influencing the track of sustainable energy adoption in the country. Through a comprehensive analysis of the Jordanian context, the goal is to extract insights that can guide policies and practices. Additionally, the findings may serve as a valuable benchmark for other regions confronting similar challenges on their pursuit for a sustainable energy future.

Climate research shows that extreme weather events and their effects are increasing in frequency, severity, and impact. Extreme wind events can cause massive societal and economic damage. High wind occurrences and their causes must be identified because they are hard to define and understand. Extreme wind modeling affects wind power plant planning, installation, and building modeling. This applies to city, vegetation, and vegetational area modeling. The scientific literature utilizes statistical, dynamic (Weather Research and Forecasting-WRF), and machine learning methods to identify extreme wind speeds. This study explores the relationship between lower-level extreme wind speeds and upper-level parameters like Z500, and T850 based on cluster analysis. The aim is to explore the correlation between upper-level atmospheric dynamics and lower-level wind behavior. K-Means cluster analysis method was employed to classify Turkish regions with similar severe wind episodes. WRF model simulation findings from NEWA (New European Wind Atlas) project (2019) were used for that purpose. The NEWA project's wind speed data at 100m a.g.l. was used for cluster analysis. We simplify the process by grid point reduction and applying the top 2% percentile as threshold value. Self-Organized Maps (SOM) clustering was also applied using the upper-level variables.

The maritime sector, grapples with environmental challenges, but the adoption of "cold ironing" emerges as a promising solution, signifying a shift toward sustainability by providing energy to ships at port, reducing reliance on fossil fuels, and significantly lowering emissions, contributing to global climate change efforts. This transition towards renewable energy is especially crucial for islands like Lesvos, addressing challenges of high energy costs and environmental degradation resulting from reliance on imported fossil fuels, highlighting the potential for positive economic and environmental impacts. The existing literature highlights a research gap in the development of Renewable Energy Sources (RES) to support cold ironing operations, specifically due to the absence of specific data for the power demand needed in such operations and the lack of monitoring data for accurate calculations. This study's primary objective is to utilize real monitoring data from the port of Lesvos to evaluate the power demand for a potential cold ironing application. Additionally, the study aims to analyze the implementation of a wind power park to meet the energy needs of an electric port and evaluate the potential reduction in CO2 emissions. The database of Marine Traffic S.A. was utilized, while the determination of the energy used in-port per ship depended on factors such as the number of arrivals, the duration of hoteling, and the type of engine used by the ships. In addition, the software RETSCREEN was used for the energy analysis of a simulated 20 MW wind park that can support the in-port operations. The combined monthly energy demand for both main and auxiliary engines of shipping vessels at Mytilini port was assessed to be 6118 MWh and averaging a power demand equaled to 8.2 MW. The simulation analysis indicates that the annual electricity delivered to the port can be72080 MWh, with a significant portion remaining unused and exported to the grid, amounting to 14956 MWh annually. Due to demand fluctuations, in-port activities require an additional 924 MWh from the main electrical grid, which highlights the importance of additional measures like energy storage and demand-response practices for the gradual transition to 100% Renewable Energy Sources (RES) operations.

This paper is devoted to the analysis of fluctuations in the solar wind plasma and interplanetary magnetic field parameters observed by Solar Orbiter and WIND spacecraft at different scales, ranging from ~10^3 to 10^7 km. We investigated two long observation intervals when the spacecraft were near the Sun-Earth line, during which the distance between the spacecraft was 0.1 and 0.5 AU respectively. It is analyzed how the fluctuation properties in different types of SW, associated with quasi-stationary and transient solar phenomena, transform on the way from the Sun to the Earth. It is shown that the time series behavior of the bulk speed subject to the least change even at the large distance between the observation points, while the time series of the IMF magnitude, components and proton density were significantly transformed even at the relatively short distance. Regardless of the assumed change in the absolute value of the parameters, the conducted statistical analysis shows that the characteristics of their fluctuations (including the level of intermittency) remains near constant regardless of the distance between the observation points and depends mostly on the type of the solar wind.

Renewable energy research becomes increasingly necessary as it grows in importance. Wind turbines are an excellent method of harnessing wind energy, which is one of the most important renewable energy sources. In light of the importance of studying wind turbine performance, this study describes the background and principles of wind turbine operation. Computational fluid dynamics (CFD) was used to evaluate the hydrodynamic performance of two types of offshore and onshore wind turbines. Mechanical power and thrust force are calculated using the CFD model for both types of turbines in a steady state based on the number of blades and rotors. The results of three-dimensional simulations are compared with those of experimental testing. Based on the method and assumptions used, the offshore turbine's mechanical torque showed an average deviation of about 4%. Increased wind speed increased mechanical power and thrust, while turbulence caused irregular pressure distributions on surfaces as a result of turbulence intensity. Furthermore, as the free wind speed increases, the blade tip and hub speed will also increase, expanding the vortices created by that flow.

The close proximity of different buildings heights can cause disturbances in the working of the smoke and ventilation ducts of lower buildings, threatening the health and even the lives of residents. To define the influence of high-rise building on the work of the ducts of the neighbouring double-storied building, experimental investigations in the wind tunnel were conducted. On this basis, empirical equations and graphs were developed leading to determining the aerodynamic coefficients considering different wind directions and the height of ducts. The direction of the wind reveals a greater influence than the height of the ducts. Properly using deflectors or increasing the height of the duct ensures maintaining static rarefaction in the area of smoke and ventilation ducts. The creation of rarefaction ensures the reliability of the natural ventilation system and the safety of the health of residents.

The overcrowding of high-rise buildings in the city adversely affects the wind environment by changing the air currents in the surrounding areas. In particular, extreme climate phenomena caused by climate change are stronger and more frequent, causing social damages in cities. To comprehensively better understand the wind properties around high-rise buildings, actual filed measurement is necessary to determine the environment assessment of wind effect. We performed the on-site measurement on LCT residential complex regions (411.6m tall) with highly concentrated high-rise buildings in coastal city Busan, South Korea under extreme weather conditions such as typhoon invasions to determine wind fluid characteristics. In the field monitoring, five anemometers were installed to analyze the wind environment around high-rise buildings when typhoon 'Hinnamnor' invaded. Compared to the nearby weather station operated by KMA(Korea Meteorological Administration), the gust was 3.7 times stronger and the max 1 min-mean wind speed was 3.1 times stronger, and the characteristics of the downward wind and the canyon wind were shown depending on the location characteristics of the point. Turbulence intensity decreased as the wind speed increased and converged to a certain value. Likewise, the gust factor also decreased as the wind speed increased and converged to 2.0, which is considered to be the parameter that best represents the intensity of the instantaneous gust caused by the skyscraper wind effect.

Sea surface wind forecasts in the Adriatic Sea often suffer for unadequate modelling, especially for the wind speed. This has detrimental effects on the accuracy of sea level and storm surge predictions. We present a numerical method to reduce the bias between the sea surface wind observed by the scatterometers and that supplied by the European Centre for Medium-Range Weather Forecasts (ECMWF) global atmospheric model, for storm surge forecasting applications. The method, called “wind bias mitigation”, relies on scatterometer observations to determine a multiplicative factor ∆ws which modulates the standard model wind in order to decrease the bias between scatterometer and model. We compare four different mathematical approaches to this method, for a total of eight different formulations of the multiplicative factor ∆ws. Four datasets are used for the assessment of the eight different bias mitigation methods: a collection of 29 Storm Surge Events (SEVs) cases in the years 2004-2014, a collection of 48 SEVs in the years 2013-2016, a collection of 364 cases of random sea level conditions in the same period, and a collection of the seven SEVs in 2012-2016 that were worst predicted by the Centro Previsioni e Segnalazioni Maree, Comune di Venezia (Tide Forecast and Early Warning Centre of the Venice Municipality - CPSM). The statistical analysis shows that the bias mitigation procedures supplies a mean wind speed more accurate than the standard forecast, when compared with scatterometer observations, in more than 70% of the analyzed cases.

In this paper we present AWEbox, a Python toolbox for modeling and optimal control of multi-aircraft systems for airborne wind energy (AWE). AWEbox provides an implementation of optimization-friendly multi-aircraft AWE dynamics for a wide range of system architectures and modeling options. It automatically formulates typical AWE optimal control problems based on these models, and finds a numerical solution in a reliable and efficient fashion. To obtain a high level of reliability and efficiency, the toolbox implements different homotopy methods for initial guess refinement. The first type of methods produces a feasible initial guess from an analytic initial guess based on user-provided parameters. The second type implements a warmstart procedure for parametric sweeps. We investigate the software performance in two different case studies. In the first case study we solve a single-aircraft reference problem for a large number of different initial guesses. The homotopy methods reduce the expected computation time by a factor of 1.7 and and the peak computation time by a factor of 8, compared to when no homotopy is applied. Overall, the CPU timings are competitive to timings reported in the literature. When the user initialization draws on expert a priori knowledge, homotopies do not increase expected performance, but the peak CPU time is still reduced by a factor of 5.5. In the second case study, a power curve for a dual-aircraft lift-mode AWE system is computed using the two different homotopy types for initial guess refinement. On average, the second homotopy type, which is tailored for parametric sweeps, outperforms the first type in terms of CPU time by a factor of 3. In conclusion, AWEbox provides an open-source implementation of efficient and reliable optimal control methods that both control experts and non-expert AWE developers can benefit from.