NiO-based nanomaterials have attracted a great deal of interest in view of various applications, that have stimulated the implementation of various synthetic approaches to control their chemico-physical properties as a function of the desired end-use. In this regard, their bottom-up preparation starting from suitable precursors plays an important role, but a molecular level in-sight into their reactivity remains an open challenge. In this study, we focus on the fragmentation of Ni(II) diketonate-diamine adducts, of interest as precursors for Ni(II) oxide systems, by com-bined electrospray ionization mass spectrometry (ESI-MS) with multiple collisional experiments (ESI-MSn) and theoretical calculations. The joint analyses revealed common features in the frag-mentation pattern of the target compounds: i) in the first-fragmentation, all three complexes form analogous base-peak cations by losing a negatively charged diketonate; in these cations, Ni-O and Ni-N interactions are stronger and the Ni positive charge is lower than in the neutral complexes; ii) the tendency of ligand electronic charge to migrate towards Ni further increases in the subsequent fragmentation processes, leading to the formation – in all three cases – of a tetracoordinated Ni environment involving an interesting cation-π intramolecular interaction.

Highly-correlated electrons – electrons that engage in strong electron-electron interactions – have been observed in transition metal oxides and quantum dots and can create unusual material behavior that is difficult to model, such as switching between a low resistance metal state and a high resistance Mott insulator state. Tests of devices using a layer-by-layer deposition process for forming multilayer arrays of ferritin (a transition metal (iron) oxide storage protein) have been previously reported that indicate that highly-correlated electron transport is occurring, consistent with models of electron transport in quantum dots. This paper reports the results of the effect of various degrees of structural homogeneity on the electrical characteristics of these ferritin arrays, as well as demonstrating that these structures can provide a switching function associated with the circuit that they are contained within, consistent with the observed behavior of highly-correlated electrons.

Solar cell layers technology has achieved global standing in the solar cell layers deposition process, and it covers the innovative methods and techniques in significant applications. Recent solar cell layers technology has an advanced interest in a refined approach to enhance performance and highlights the importance of recent proficient procedures for manufacturing. For example, the application is used to search for novel materials for solar cells' layers to clarify the current energy crisis. The technological process and various types of solar cells depend on climate change. Among them, layers of solar cells and silicon wafer solar cells are very encouraging. Solar cell layers technology has led to solar cells being a more reasonable active option in design and production. The productivities facilitated by new solar cells still need to be enhanced for the various processes involved in the additional enhancement from Copper Indium Gallium Selenide (CIGS) microfilms to solar cell crystal structure dye-sensitized solar cells. The hydrophobic coating works as an anti-dust coating, enhancing efficiency and decreasing the cost of cleaning solar cells. In Saudi Arabia Majmaah City, most solar projects are in dry regions, where the dusty weather reduces solar cell efficiency. Therefore, combining these two properties and applying an anti-reflective and superhydrophobic coating will increase solar cell efficiency by 20%. Solar cells' crystal structure results are substituted with layers or new materials to balance environmental impact and toxic nature.

Titanium dioxide (TiO2) and aluminum oxide (Al2O3) coatings have been investigated in a wide range of bio-applications due to their biodegradation and biocompatibility properties, that are key parameters for their use in the food packaging and biomedical devices fields. The present study evaluates and compares the electrochemical behavior of the non-coated, commercial resin-coated, TiO2-coated and Al2O3-coated aluminum in commercial beer electrolyte. For this, TiO2 and Al2O3 thin films were deposited on aluminum (Al) substrates using atomic layer deposition (ALD). The evaluation of the corrosion barrier layer properties was performed by linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS). In addition, profilometry, grazing incidence X-ray diffractometry (GIXRD), scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR) analyses were performed to investigate the physical and chemical properties of the pristine and / or corroded samples. TiO2 and Al2O3 films presented an amorphous structure, a morphology that follows Al substrate surface, and a thickness of around 100 nm. Analysis of LSV data showed that ALD coatings promoted a considerable increase in corrosion barrier efficiency being 86.3% for TiO2-coated Al and 80% for Al2O3-coated Al in comparison with 7.1% of commercial resin-coated Al. This is mainly due to the lower electrochemical porosity, 11.4% for TiO2-coated Al and 20.4% for Al2O3-coated Al in comparison with 96% of the resin-coated Al, i.e. an increase of up to twofold in the protection of Al when coated with TiO2 compared to Al2O3 coated. The EIS results allow us to complement the discussions about the reduced corrosion barrier efficiency of the Al2O3 film for beer electrolyte once SEM and FT-IR analyzes did not show drastic changes in both investigated ALD films after the corrosion assays. The above results indicate that ALD TiO2 and Al2O3 films may be a viable alternative to replace the synthetic resin coatings frequently used in aluminum cans of use in the food industry.

A potassium bromide KBr material, which has been widely used as the key element in the Fourier spectrometers and as the output window of the IR-lasers, has been studied with good advantage via applying the carbon nanotubes in order to modify the potassium bromide surface. The laser oriented deposition method has been used to place the carbon nanotubes at the matrix material surface in the vertical position at the different electric field varied from 100 to 600 V×cm-1. The main idea of the improvement of the spectral properties of the potassium bromide structure is connected with the fact that the refractive index of the carbon nanotubes is substantially less than the refractive index of the studied material, and the small diameter of the carbon nanotubes allows one to embed these nano-objects in the voids of the lattice of the model matrix systems. Moreover, the mechanical characteristics and wetting features of the potassium bromide structures have been investigated under the condition mentioned above. Analytical and quantum-chemical simulations have supported the experimental results.

The use of the LMD technology as a manufacturing and repairing technique in industrial sectors like the die and mold and aerospace is increasing within the last decades. Research carried out in the field of LMD process situates argon as the most usual inert gas, followed by nitrogen. Some leading companies have started to use helium and argon as carrier and shielding gas, respectively. There is therefore a pressing need to know how the use of different gases may affect the LMD process due to there is a lack of knowledge with regard to gas mixtures. The aim of the present work is to evaluate the influence of a mixture of argon and helium on the LMD process by analyzing single tracks of deposited material. For this purpose, special attention is paid to the melt pool temperature, as well as to the characterization of the deposited clads. The increment of helium concentration in the gases of the LMD processes based on argon will have three effects. The first one is a slightly reduction of the height of the clads. Second, an increase of the temperature of the melt pool. Last, smaller wet angles are obtained for higher helium concentrations.

In this work, nanocomposite photoelectrodes of the TiO2/ Au composition were manufactured, in which the size of plasmonic Au nanoparticles was varied, and the morphology of the TiO2 layer, depending on the thickness, changed from an island to a continuous layer. The influence of the morphology of plasmonic Au nanoparticles and the TiO2 layer on the optical and photoelectrochemical characteristics of hybrid photoelectrodes was studied. It has been shown that continuous coating of Au nanoparticles with a TiO2 layer (layer thickness 10 and 15 nm) leads to a decrease in the photoelectric response, and the decrease in photocurrent density and photoconversion efficiency decreases in proportion to the thickness of the TiO2 layer. The indicated drop in characteristics when plasmonic particles are located under the TiO2 layer is presumably associated with the scattering and recombination of charge carriers in the semiconductor layer. The best performance was shown by a system in which large Au nanoparticles (10 nm) are coated with a 5 nm thick layer of titanium dioxide; in this geometry, Au nanoparticles are decorated with TiO2 nanoparticles, as a result of which the photoelectrode-electrolyte interface has a more complex structure.

Sediment cores were collected from a mudflow lobe (80 m water depth) offshore of the Mississippi River’s Southwest Pass in 2017 to better understand the sedimentology near the lobe entraining the SS Virginia shipwreck (sunk by a German U-Boat in 1942) and surrounding Mississippi River Delta Front. Core analyses included 210Pb/137Cs geochronology, granulometry, and X-radiography. Sediment accumulation rates (SAR) calculated from excess 210Pb activity in multicores are 0.22–0.29 cm/yr at seabed depths less than 20 cm and 0.29–0.51 cm/year at depths greater than 20 cm. 137Cs accumulation rates are ~0.15 to ~ 0.37 cm/year since 1954 and 1963 respectively. Sediment accumulation rates from 210Pb and 137Cs geochronology and indicators of relative sedimentation and bioturbation from X-radiographs suggest that rates of sediment accumulation near Virginia have declined since ca. the mid-20th century. This may be explained by the multi-decade downslope mass transport of the mudflow lobe in which the shipwreck is embedded, and decreases in sediment supply delivered offshore from the Mississippi River. Mass-transport calculations of the Virginia lobe derived from core properties and published lobe advection rates suggest downslope mass transport is far higher than sediment resupply from the Mississippi River, consistent with recent studies of delta retreat.

Pharmaceutical aerosols play a key role in the treatment of lung disorders, but also systemic diseases, due to their ability to target specific areas of the respiratory system (RS). This article focuses on identifying and clarifying the influence of various factors involved in the generation of aerosol micro- and nanoparticles on their regional distribution and deposition in the RS. Attention is given to the importance of process parameters during aerosolization of liquids or powders and the role of aerosol flow dynamics in RS. The interaction of deposited particles with the fluid environment of the lung is also pointed out as an important step in the mass transfer of the drug to the RS surface. The analysis presented highlights the technical aspects of preparing the precursors to ensure that the properties of the aerosol are suitable for a given therapeutic target. Analyzing existing technical limitations, several potential strategies for enhancing the efficiency of targeted therapeutic delivery to or through the respiratory system are identified and presented, including the use of smart inhaling devices incorporating AI algorithms.

Antimicrobial peptides (AMPs) have emerged as a promising solution to tackle bacterial infections and combat antibiotic resistance. However, their clinical application has been hindered by their vulnerability to protease degradation and toxicity towards mammalian cells. To overcome these challenges, our study aims to develop a method to enhance the stability and safety of AMPs, applicable to effective drug-device combination products. KR12 antimicrobial peptide was chosen and in order to further enhance its delivery and efficacy, HIV TAT protein-derived cell-penetrating peptide (CPP) was fused to form CPP-KR12. A new product, CPP-KR12@Si, was developed by forming silica nanoparticles with self-entrapped CPP-KR12 peptide using the biomimetic silica precipitability due to its cationic nature. Peptide delivery from CPP-KR12@Si to bacteria and cells was delivered at a slightly delayed rate with improved stability against trypsin treatment and a reduction in cytotoxicity over CPP-KR12. Finally, the antimicrobial potential of CPP-KR12@Si/bone graft substitute (BGS) combination product was demonstrated, which is coated with CPP-KR12 in the form of nanoparticles on the surface of BGS. Self-entrapped AMP in silica nanoparticles is a safe and effective AMP delivery method that will be useful for developing a drug/device combination product for tissue regeneration.

The most modern technique utilized to create intricate and complexly manufactured parts for a variety of applications is called additive manufacturing (AM). Fused deposition modeling (FDM) has received the greatest attention in the development and manufacturing sectors. The main objective of this study was to investigate how printing factors affected the mechanical characteristics of printed samples. Samples were produced using an FDM 3D printer in compliance with ASTM D638 using a variety of input settings, including orientation, layer thickness, speed, and infill pattern. On the printed samples, tensile tests and morphological analysis using a scanning electron microscope (SEM) were done. The findings of this study demonstrate that factors including layer thickness, printing speed, and orientation significantly affect the tensile strength of ABS printed samples. Discovering the process settings that could lead to superior mechanical and physical characteristics would undoubtedly assist designers and manufacturers worldwide as the FDM 3D printer becomes more and more crucial in manufacturing engineering parts.

Three-layer structures based on various multi-component films of III–V semiconductors heavily doped with Fe were grown by pulsed laser sputtering of InSb, GaSb, InAs, GaAs and Fe solid targets. The structures comprising InAsSb:Fe, InGaSb:Fe and InSb:Fe layers with Fe concentrations up to 24 at. % separated by GaAs spacers were deposited on (001) i-GaAs substrates at 200ºC. Transmission electron microscopy showed that the structures have a rather high crystalline quality and do not contain secondary-phase inclusions. X-ray photoelectron spectroscopy investigations revealed significant diffusion of Ga atoms from the GaAs regions into the InAsSb:Fe layers, which has led to the formation of an InGaAsSb:Fe compound with a Ga content up to 20 at. %. It has been found that the ferromagnetic properties of the InAsSb:Fe magnetic semiconductor improve with increasing Sb:As ratio. It has been concluded that the indirect ferromagnetic exchange interaction between Fe atoms occurs predominantly via Sb atoms.

Laser direct writing allows for the fabrication of complex structures, which is particularly advantageous in micro-optic applications. However, the increasing demand for optics quality requires the lowest optical power loss, which can occur from unwanted reflections. This research demonstrates the possibility of forming an anti-reflective coating on hybrid-polymer micro-lenses fabricated by employing laser direct writing (LDW), without changing their geometry. Such coating deposited by atomic layer deposition (ALD) decreased the reflection from 3.3 % to 0.1 % at the wavelength of 633 nm for one surface of SZ2080™.

In this study the formation of thin-film barrier coatings based on a highly-conducting Bi1.60Er0.4O3 (EDB) solid electrolyte on supporting Ce0.8Sm0.2O1.9 (SDC) electrolyte substrates is implemented for the first time using electrophoretic deposition (EPD). Electrokinetic properties of EDB-based suspensions in a non-aqueous dispersion medium of isopropanol modified with small additions of polyethyleneimine (PEI, 0.26 g/L) and acetylacetone (0.15 g/L), as well as in a mixed isopropanol/acetylacetone (70/30 vol.%) medium are studied. The dependences of the thickness of EDB coatings on voltage and deposition time are obtained using deposition on a model Ni-foil electrode. Preliminary synthesis of a conductive polypyrrole (PPy) polymer film is used to create surface conductivity of non-conductive SDC substrates. The efficiency of using a modified dispersion medium based on isopropanol to obtain a continuous EDB coating 12 μm thick, sintered at a temperature of 850 °C for 5 h, is shown. The microstructure and morphology of the surface of the EDB coating are studied. Pt/SDC/EDB/Pt cell is used to characterize the coating conductivity. The EPD method is shown to be promising for the formation of barrier coatings based on doped bismuth oxide. The developed method can be used for creating cathode barrier layers in SOFC technology.

Bioglasses are highly adoptable bone substitute materials, which can be combined with so-called therapeutic ions. These ions have shown to influence underlying molecular processes of the bone regeneration cascade. Moreover, it is known that bone substitutes induce an immune reaction within their implantation area involving macrophages and their pro- and anti-inflammatory subtypes dependent on their chemical composition. However, only poor knowledge exists regarding the influence of therapeutic ions onto the immune reactions and the associated bone healing. Thus, the aim of this work was to investigate the influence of strontium- and copper-doped bioglasses on the induction of M1- and M2-macrophages as well as the implant bed vascularization. (2) Methods: For this study, two alkali glasses were produced on basis of ICIE-16 bioglass via the melt-quench route with the addition of 5 wt% copper or strontium (ICIE16-Cu and ICIE16-Sr). Pure ICIE16 and 45S5 bioglasses were used as control materials. The bioactivity (ion release), chemical composition and the surface pattern were investigated, as well as an in vivo experiment was performed using the subcutaneous implantation model in rats. (3) Results: SEM imaging showed different formations of hydroxyapatite on the surfaces of the bioglass systems after submersion in simulated body fluid. EDX analysis confirmed the doping process by showing the release kinetics. Copper-doped bioglass exhibited a higher ion release than strontium-doped bioglass. Copper induced both a low immune cell migration and triggered a low number of M1- and M2-macrophages but also of blood vessels. The strontium-containing bioactive glass induced higher numbers of M1-macrophages after 30 days. Both copper- and strontium-doped bioglasses induced comparable numbers of M2-macrophages as found in the control groups. (4) Conclusions: Bioglass doping with copper and strontium did not exhibit significant influence on the foreign body response or the implantation bed vascularization in vivo. However, the prepared bioglass systems seemed to be biocompatible.

Electroless etching of semiconductors was elevated to an advanced micromachining process by the addition of a structured metal catalyst. Patterning of the catalyst by lithographic techniques facilitates the patterning of crystalline and polycrystalline wafer substrates. Galvanic deposition of metals on semiconductors has a natural tendency to produce nanoparticles rather than flat uniform films. This characteristic makes possible the etching of not only wafers but also particles with arbitrary shape. While it has been widely recognized that spontaneous deposition of metal nanoparticles can be used in connection with etching to porosify wafers, it is also possible to produced nanostructured powders. MACE can be controlled to produce (1) etch track pores with shapes and sizes closely related to the shape and size of the metal nanoparticle, (2) hierarchically porosified substrates exhibiting combinations of large etch track pores and mesopores, and (3) nanowires with either solid or mesoporous cores. This review discussed the mechanisms of porosification, processing advances and the properties of the etch product with special emphasis on the etching of silicon powders.

Over the last decade, a significant literature has emerged that advocates the potential of different Additive manufacturing (AM) technologies and printable polymeric materials. Nevertheless, large scale printing and complex geometric shapes, with curvatures and non-planar layer deposition, are a challenging process for the traditional gantry-based machine. The 3 degrees of freedom cartesian configuration restricted their capability to planar layered printing and restricted part dimensions. To date, many researchers have used industrial robots to overcomes this limitation. This review gives the reader a good overview of the FDM technique due to its scalability, cost efficiency and a wide range of material printability. A strong emphasis is laid on the PLA and PLA-based composites as promising materials for the FDM process applications. The second part of this paper links the successful use of these materials in the traditional printing process to large scale printing using the robot-based FDM process. This survey presents representative setups for robot-based AM and works that have been used these setups for non-planar material deposition. Finally, we conclude this paper by identifying opportunities for realizing new functional capabilities by exploiting robot-based AM, and we also present the future trends in this area.

This work aimed to assess and characterize the air quality in what concerns particulate pollution in urban-industrial environments. The main objectives were to study the spatial variability of the deposition flux of particulate pollution identifying areas with higher deposition, associate the variability with climatological variables and with possible surrounding emitting sources. The method for collecting the deposited particles was based on the standard NF X 43-007. Sampling for particulate pollution took place between April 2015 and February 2016, through seven sampling campaigns. Maps of the spatial dispersion for the particulate pollution were obtained through statistics and geostatistics techniques. Elemental identification by scanning electron microscopy (SEM) was also used but only in two sampling campaigns. The results show that the sampling campaigns that took place during hot and dry periods, 2nd and 3rd, present higher deposition flux: 2.04 g/(m2 x month) and 1.72 g/(m2 x month), respectively. Lower deposition fluxes were registered in the 6th and 7th campaigns: 0.23 g/(m2 x month) and 0.24 g/(m2 x month), respectively. It was also observed a recurrent high deposition at specific sampling points which may be due to both the nearby road traffic and the presence of chimneys. SEM analysis allowed to associate repetitive element deposition, at the same sampling point, to the same emitting source.

Tungsten oxides play a pivotal role in a variety of modern technologies e.g., switchable glasses, wastewater treatment, and modern gas sensors. Metallic tungsten is used as armor material, for e.g., gas turbines as well as future fusion power devices. In the first case, oxides are desired as functional materials, while in the second case, oxides can lead to catastrophic failures, so avoiding the oxidation of tungsten is desired. In both cases, it is crucial to understand the reactivity of tungsten oxides with other chemicals. In this study, the different reactivities of tungsten oxides with the highly-oxophilic beryllium are studied and compared. Tungsten-(IV)-oxide and tungsten-(VI)-oxide layers are prepared on a tungsten substrate. In the next step, a thin film of beryllium is evaporated on the samples. In consecutive steps, the sample is heated in steps of 100 K from r. t. to 1273 K. The chemical composition is investigated after each experimental step by high-resolution X-ray photoelectron spectroscopy (XPS) of all involved core levels as well as the valence band. A model is developed to analyze the chemical reactions after each step. In this study, we find that tungsten trioxide was already reduced by beryllium at r. t. and started to react to form the ternary compounds BeWO₃ and BeWO₄ at temperatures starting from 673 K. However, tungsten dioxide is resistant to reduction at temperatures of up to 1173 K. In conclusion, we find WO₂ to be much more chemically resistant to the reduction agent Be than WO₃.

Interfaces between layers in 3D-printed elements produced by extrusion-based material deposition were investigated on both macro- and micro-scales. On the macro-scale, compression and bend tests were performed on two 3D-printable cement-based compositions (3PCs), namely C1 and C2. The influences of binder composition and time interval between layers on layer-interface strength were critically analyzed. In the context of additive manufacturing, the optimized composition C2, containing pozzolanic additives, exhibited mechanical performance superior to that of the mixture with Portland cement as the sole binder. In particular, Mixture C2 showed a less pronounced decrease in interface tensile strength. Even for time intervals between depositions of two layers as long as 1 day the loss in corresponding flexural strength was below 25%, as compared with C2 specimens tested in the perpendicular direction. In contrast, the decrease in flexural strength measured for C1 specimens amounted to over 90% for the same set of parameters. Higher porosity at the interfaces of the printed concrete layers was identified as the cause for the lower interface strengths of C1. Microscopic observations supported the findings of the macroscopic investigations. While a pronounced recovery (“self-healing”) of the porous, discontinuous interlayers was observed with increasing age for Mixture C2, in case of C1 the filling products grown in the porous interlayer were found to be non-strengthening.

Polylactic Acid (PLA) is an organic polymer commonly used in fused deposition (FDM) printing and biomedical scaffolding that is biocompatible and immunologically inert. However, variations in source material quality and chemistry make it necessary to characterize the filament and determine potential changes in chemistry occurring as a result of the FDM process. We used several spectroscopic techniques, including laser confocal microscopy, Fourier-Transform Infrared (FTIR) spectroscopy and photoacousitc FTIR spectroscopy, Raman spectroscopy, and X-ray photoelectron Spectroscopy (XPS) in order to characterize both the bulk and surface chemistry of the source material and printed samples. Scanning Electron Microscopy (SEM) and Differential Scanning Calorimetry (DSC) were used to characterize morphology, crystallinity, and the glass transition temperature following printing. Analysis revealed calcium carbonate-based additives which were reacted with organic ligands and potentially trace metal impurities, both before and following printing. These additives became concentrated in voids in the printed structure. This finding is important for biomedical applications as carbonate will impact subsequent cell growth on printed tissue scaffolds. Results of chemical analysis also provided evidence of the hygroscopic nature of the source material and oxidation of the printed surface, and SEM imaging revealed micro and sub-micron scale roughness that will also impact potential applications.

Special preparation of SBA-15 materials has been carried out for creating adsorbents exhibiting an enhanced and selective adsorption toward CO2. This creation starts from an adequate conditioning of the silica surface, via a thermo-alkaline treatment to increase the population of silanol species on it. CO2 adsorption is only reasonably achieved when the SiO2 surface becomes aminated after put in contact with a solution of an amino alkoxide compound in the right solvent. Unfunctionalized and amine-functionalized substrates were characterized through X-ray diffraction, N2 sorption, Raman spectroscopy, electron microscopy, 29Si solid-state NMR, and NH3 thermal programmed desorption. These analyses proved that the thermo-alkaline procedure desilicates the substrate and eliminates the micropores (without affecting the SBA-15 capillaries), present in the original solid. NMR analysis confirms that the hydroxylated solid anchors more amino functionalizing molecules than the unhydroxylated material. The SBA-15 sample subjected to hydroxylation and amino- functionalization displays a high enthalpy of interaction, a reason why this solid is suitable for a strong deposition of CO2 but with the possibility of observing a low-pressure hysteresis phenomenon. Contrastingly, CH4 adsorption on amino-functionalized, hydroxylated SBA-15 substrates becomes almost 5 times lesser than the CO2 one, thus giving proof of their selectivity toward CO2.

In the previous work, the pure fatigue behavior of AM60 magnesium alloy (PF-AM60) was compared with the corrosion fatigue behavior of these specimens (CF-AM60). In this research, in continuation of the previous job, the pure fatigue behaviors of AM60 with polylactic acid (PLA) coating (PF-AM60-PLA) and also, corrosion fatigue behaviors of magnesium alloy with PLA coating (CF-AM60-PLA) were evaluated. Polymer coating was made by fused deposition modeling (FDM) with a 3D printer and attached to standard fatigue test specimens with a glue. Then, they were immersed in the simulated body fluid (SBF) for 27 days. In the end, a high-cycle bending fatigue test was performed on samples. The fracture surface of the samples was also observed using the field emission scanning electron microscopy (FESEM). Due to corrosion, the weight of the specimens redcued by an average of 35%. The corrosion rate decreased in the first 7 days and then increased. PF samples with coating had an average of 49% increase in fatigue lifetime. Regarding the CF samples, despite the use of a 10 times stronger solution, the fatigue lifetime of these samples decreased by only 35%. FESEM results also showed cleavage plates and striations. In addition, the separation of the glue from the coating and Mg was observed. Corrosion products including microcracks and holes were seen on the fracture surface of CF specimens, which caused stress concentration and crack growth. Holes caused by the release of gases were also observed in polymer coatings.

In order to enhance the gain of antenna suitable for the airplane mounted platform, a conformal tightly coupled antenna array is investigated in this paper. Especially, three-dimensional (3-D) inkjet printing technique is used to implement the conformal property. The printing of antenna substrate and radiation layer is implemented by combining the fused deposition modelling and microdroplet injection molding technologies based on the existing 3-D printer. Here, through a unique combination of 3-D and 2-D inkjet printing of dielectric material and metallic ink, respectively, we demonstrate a monolithically integrated to a nonplanar antenna for the first time. Antenna measurements show that the complete characterization of this new process in terms of minimum feature sizes and achievable conductivities. This antenna configuration offers a high-gain performance with low-cost and rapid fabrication technique by using 3-D printing. The voltage standing wave ratio and radiation patterns are tested after adding the newly designed feed structure. Results shown the design process much efficient. Both antenna element and the array with good properties, which are in very good agreement with the specially mounted platform.

Transparent conducting oxides (TCO) with high electrical conductivity and at the same time high transparency in the visible spectrum are an important class of materials widely used in many devices requiring a transparent contact such as light-emitting diodes, solar cells and display screens. Since the improvement of electrical conductivity usually leads to degradation of optical transparency, a fine-tuning sample preparation process and a better understanding of the correlation between structural and transport properties is necessary for optimizing the properties of TCO for use in such devices. Here we report a structural and magnetotransport study of tin oxide (SnO₂), a well-known and commonly used TCO, prepared by a simple and relatively cheap Atmospheric Pressure Chemical Vapour Deposition (APCVD) method in the form of thin films deposited on soda-lime glass substrates. The thin films were deposited at two different temperatures (which were previously found to be close to optimum for our setup), 590 °C and 610 °C, and with (doped) or without (undoped) the addition of fluorine dopants. Scanning Electron Microscopy (SEM) and Grazing Incidence X-ray Diffraction (GIXRD) revealed the presence of inhomogeneity in the samples, on a bigger scale in form of grains (80–200 nm), and on a smaller scale in form of crystallites (10–25 nm). Charge carrier density and mobility extracted from DC resistivity and Hall effect measurements were in the ranges 1–3 × 10²⁰ cm⁻³ and 10–20 cm²/Vs, which are typical values for SnO₂ films, and show a negligible temperature dependence from room temperature down to -269 °C. Such behaviour is ascribed to grain boundary scattering, with the interior of the grains degenerately doped (i.e., the Fermi level is situated well above the conduction band minimum) and with negligible electrostatic barriers at the grain boundaries (due to high dopant concentration). The observed difference for factor 2 in mobility among the thin-film SnO₂ samples most likely arises due to the difference in the preferred orientation of crystallites (texture coefficient).

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

Neutral beam injection (NBI) is used for thermonuclear plasma heating, non-inductive current drive, rotation, operation scenario control, and for plasma diagnostics in nuclear fusion devices. NBI is the main source of fast particles in plasma which transmit energy to thermal plasma during their slow-down. Steady-state tokamak operation is only possible when the sub-thermal particles energy is absorbed and effectively confined in plasma volume. While NBI purposes and applications vary through different fusion systems, the engineering tasks performed during research and development (R&D) stage of neutral beamline design have much in common. The NBI studies, especially addressing long pulse and high-power operation typically include a beam transmission analysis and power loads distribution at the structural components of the beamline. Thermo-structural analysis is applied next to heat removal circuits design. ‘Beam Transmission’ (BTR) code is a dedicated tool, developed by a physicist and used by NBI physicists and engineers. BTR was created and 1^st applied during R&D phase of the world’s largest tokamak ITER. BTR code is intended for public usage and routinely applied for detailed simulations of neutral beam propagation through complex beamlines. BTR is flexible and intuitive in input, user-friendly and fully interactive. Thanks to visualization and high performance BTR looks and feels like a real NB flight simulator. Despite BTR ‘mature’ age, the code is still in evolution. Support is available to all new BTR users.

Vertical graphene nanowalls (VGNWs) have emerged as a highly promising material in recent years due to their exceptional properties, such as a high specific surface area, excellent electrical conductivity, scalability, and compatibility with transition metal compounds. These attributes make VGNWs a compelling candidate for various applications, including energy storage, catalysis, and sensing, fostering great interest in their use in next future commercial graphene-based sensors like optoelectronic and plasmonic devices, energy storage electrodes, and catalytic systems. Among the diverse graphene synthesis methods, plasma-enhanced chemical vapor deposition (PECVD) has proven to be a robust technique for producing large-scale graphene films and creating VGNWs on diverse substrates. However, despite substantial progress in optimizing growth conditions to achieve micrometer-sized graphene nanowalls, the outcomes are often obtained through empirical approaches, and a comprehensive understanding of the underlying physicochemical mechanisms governing nanostructure formation remains elusive. In particular, a deeper exploration of atomic-level phenomena, such as nucleation, carbon precursor adsorption, and surface diffusion of adatoms, is imperative to exert precise control over the growth process. Concerning the synthesis of VGNWs, hydrogen plays a dual role in the graphene growth process, acting as both a co-catalyst and an etchant for the nanowalls. Nevertheless, a thorough comprehension of the intricate growth process is still required. To address these knowledge gaps, this review paper aims to investigate the nucleation and growth of VGNWs using PECVD, with a specific focus on exploring the temperature effect on the graphene growth ratio and nucleation density across a wide range of temperatures. By providing valuable insights into the PECVD process, our objective is to enable the optimization of growth conditions for tailoring VGNWs' properties, thereby facilitating their application in energy storage, catalysis, and sensing fields.

Ultralong carbon nanotubes (UCNTs) are highly demanded for nanocomposites applications because of their magnificent physical and chemical properties. UCNTs are synthesized by catalytic chemical vapor deposition (CCVD) method and, before using as fillers in nanocomposites, should be purified from residual catalyst and non-CNT particles without significant destruction or scissoring of UCNTs. The role of water vapor for purification of UCNTs is investigated, the importance of water assistance in this process is confirmed. It was shown that wet air treatment of products of UCNTs CCVD synthesis under mild conditions can be used to decrease sufficiently residual catalyst content without significant carbon losses in comparison with the results obtained with dry air, while the residual iron content was shown to influence heavily on the subsequent oxidation of different forms of carbons, including UCNTs. The increasing of D/G ratio of Raman spectra after wet air treatment of products of UCNTs CCVD synthesis makes it possible to conclude that iron catalyst particles transform into iron oxides and hydroxides that caused inner structural strains and destruction of carbon shells improving removal of the catalyst particles by subsequent acid treatment. UCNTs purification with water assistance can be used to develop economically and ecologically friendly methods for obtaining fillers for nanocomposites of different applications.

A variety of techniques have been utilized in metal additive manufacturing (AM) for melt pool size management, including modeling and feed-forward approaches. In a few cases, closed-loop control has been demonstrated. In this research, closed-loop melt pool size control for large-scale, laser-wire based Directed Energy Deposition is demonstrated with a novel modification: site-specific changes to the controller set-point were commanded at trigger points, the locations of which were generated by the projection of a secondary geometry onto the primary 3D-printed component geometry. The present work shows that, through this technique, it is possible to print a specific geometry that occurs beyond the actual toolpath of the print head. This is denoted as an extra-toolpath geometry and is fundamentally different from other methods of generating component features in metal AM. A proof-of-principle experiment is presented in which a complex oak leaf geometry was embossed on an otherwise ordinary double-bead wall made from Ti-6Al-4V. The process is introduced and characterized primarily from a controls perspective with reports on the performance of the control system, the melt pool size response, and the resulting geometry. The implications of this capability, which extend beyond localized control of bead geometry to the potential mitigations of defects and functional grading of component properties, are discussed.

Controlling functional properties of matter and combine them for engineering a functional device is nowadays a common direction of scientific community. For instance, heterogeneous magnetic nanostructures can make use of different types of geometrical and compositional modulations to achieve the control of the magnetization reversal along with the nano-entities and thus enabling the fabrication of spintronic, magnetic data storage and sensing devices, among others. In this work, diameter modulated FeNi nanowires are fabricated paying special effort to obtain sharp transition regions between two segments of different diameters (from about 450 nm to 120 nm), enabling precise control over the magnetic behavior of the sample. Micromagnetic simulations performed on single bi-segmented nanowires predict a double step magnetization reversal where the wide segment magnetization switches near 200 Oe through a vortex domain wall, while at 500 Oe the magnetization of the narrow one is reversed through a corkscrew like mechanism. Finally, these results are confirmed with magneto-optic Kerr effect measurements at the transition of isolated bi-segmented nanowires. Furthermore, macroscopic vibrating sample magnetometry is used to demonstrate that the magnetic decoupling of nanowire segments is the main phenomenon occurring over the entire fabricated nanowires.

The manufacturing method influences the properties of the produced components. This work investigates the influence of manufacturing methods such as fused filament fabrication (3D printing) and injection molding on water absorption, mechanical and thermal properties of the specimens produced from neat biobased poly(lactic acid) (PLA) polymer and poly(lactic acid)/wood composites. Acrylonitrile butadiene styrene (ABS) acts as the reference material due to its low water absorption and good functional properties. The printing layer thickness is one of the factors that affects the properties of a 3D printed specimen. The investigation includes two different layer thicknesses (0.2 mm and 0.3 mm) while maintaining uniform overall thickness of the specimens across two manufacturing methods. 3D printed specimens absorb significantly higher amounts of water than the injection molded specimens, and the increase in the layer thickness of the 3D printed specimens contributes to further increased water absorption. However, the swelling due to water absorption in 3D printed specimens decreases on increased layer thickness. Tensile, flexural and impact properties of all the specimens decrease after water absorption while the properties improve on decreasing the layer thickness. Higher porosity on increasing the layer thickness is the predominant factor. The results from dynamic mechanical analysis and microscopy validate the outcomes.

: Low-temperature growth of diamond films by chemical vapor deposition (CVD) method is not so widely reported and especially its initial periods of nucleation and growth phenomenon are of particular interest to the researchers. Four sets of substrates were selected for growing diamond films by linear antenna microwave plasma enhanced CVD (LA-MPCVD). Among them, silicon and sapphire substrates were pre-treated with detonation nanodiamond (DND) seeds before diamond growth for enhancement of its nucleation. On the other hand, carbon nanotube (CNT) films on Si substrates were also used as another template for LA-MPCVD diamond growth. In order to enhance the diamond nucleation during CVD growth, some of the CNT films were again pre-treated by electrophoretic deposition (EPD) of diamond nanoparticles. All these substrates were then put inside the LA-MPCVD chamber for growing diamond films under variable processing conditions. Microwave input powers (1100 – 2800 W), input power modes (pulse or continuous), antenna to stage distances (5 - 6.5 cm), process gas recipes (with or without CO2), methane gas percentages (3 - 5%), deposition times (11 – 120 minutes) were altered to investigate their effect on the growth of diamond film on the pre-treated substrates. The substrate temperatures were found to vary from as low as 170oC to a maximum of 307oC during the alteration of the different processing parameters. Contrary to the conventional MPCVD, it was observed that during the first hour of LA-MPCVD diamond growth, DND seeds or the nucleating structures, do not coalesce together to make a continuous film. Deposition time was the most critical factor in fully covering the substrate surfaces with diamond film, since the substrate temperature could not become stable during the first hour of LA-MPCVD. CNT was found to be oxidised rapidly under LA-MPCVD plasma conditions; therefore, a CO2-free process gas recipe was used to reduce CNT burning. Moreover, EPD-coated CNT was found to be less oxidised by the LACVD plasma during diamond growth.

A series of defective ZSM-5 zeolites (~300 nm, SiO₂/Al₂O₃ ratio of 55, 100, 400 and 950) were intentionally prepared and systematically studied by XRD, SEM, ²⁹Si MAS NMR, argon physisorption, NH₃-TPD and FT-IR technologies. The nature, the amount and the accessibility of the acid sites of defective ZSM-5 zeolites are greatly different from reported ZSM-5 zeolites with perfect crystal structure. The co-existed strong Brønsted acid sites (Si(OH)Al) and weak Brønsted acid sites (hydroxyl nests) over defective ZSM-5 zeolites might lead to unique catalytic function. Zn(C₂H₅)₂ was grafted onto defective ZSM-5 zeolites through chemical liquid deposition (CLD) method. Interestingly, FT-IR spectroscopy studies find that Zn(C₂H₅)₂ was preferentially grafted on the hydroxyl nests with weak acidity rather than the Si(OH)Al groups with strong acidity over different defective ZSM-5 zeolites. Particularly, home-built operando dual beam FTIR-MS was applied to study the catalytic performance of Zn species locating at different sites of defective ZSM-5 zeolites under n-hexane transformation. Results show that Zn species grafted over hydroxyl nests obtain better dehydrogenation performance than Zn species over framework aluminum. This study provides guidance for the rational design of highly efficient alkane dehydrogenative aromatization catalysts.

The composition of fine-ground lead zirconate-titanate powder Pb(Zr_0.52Ti_0.48)O₃, suspended in PZT and bismuth titanate (BiT) solutions, is deposited on the curved surface of IN718 and IN738 nickel-based supper alloy substrates up to 100 µm thickness. Photochemical metal organic and infiltration techniques are implemented to produce smooth, semi-dense, and crack-free random orientated thick piezoelectric films as piezo-sensors, free of any dopants or thickening polymers. Every single layer of the deposited films is heated at 200 °C with 10 wt.% excess PbO, irradiated by UV lamp (365 nm, 6 watt) for 10 minutes, pyrolyzed at 400 °C, and subsequently annealed at 700 °C for one hour. This process is repeated successively until reaching the desired thickness. Au and Pt thin films are deposited as the bottom and top electrodes using evaporation and sputtering methods, respectively. PZT/PZT and PZT/BiT composite films are then characterized and compared to similar PZT and BiT thick films deposited on the similar substrates. The effect of composition and deposition process is also investigated on the crystalline phase development and microstructure morphology as well as dielectric, ferroelectric and piezoelectric properties of piezo-films. The maximum remnant polarization of P_r = 22.37 ± 0.01, 30.01 ± 0.01 µC/cm², the permittivity of ε_r = 298 ± 3, 566 ± 5 and piezoelectric charge coefficient of d₃₃ = 126, 148 m/V were measured versus the minimum coercive field of E_c = 50, 20 kV/cm for the PZT/PZT and PZT/Bit thick films, respectively. The thick film piezo-sensors are developed to be potentially used at frequency bandwidth of 1–5 MHz for rotary structural health monitoring and also in other industrial or medical applications as a transceiver.

This work investigates how the user-controlled parameters of the 3D printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence the structure and strength of the part. The process studied is fused filament fabrication with a desktop 3D printer and the material utilized is PLA (polylactic acid). As a characteristic of the part strength the fracture load in the case of a three-point bend and calculated related stress were used. During the printing process parts were oriented with the long side along the Z axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. During the fabrication process, temperature distribution on the sample surface was monitored with thermal imager. Sample mesostructure was analyzed using SEM. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. The influence of all the parameters can be expressed through two generalizing factors: the temperature of the previous layer and the flow efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads). It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength.

The current paper is studying the influence of geometrical parameters of the FDM (FFF) 3D printing process on printed part strength for open source desktop 3D printers and the most popular material used for that purpose, i.e. PLA (polylactic acid). The study was conducted using a set of different nozzles (0.4, 0.6 and 0.8 mm) and a range of layer heights from the minimum to maximum physical limits of the machine. To assess print strength, a novel assessment method is proposed. A tubular sample is loaded in the weakest direction (across layers) in a three-point bending fixture. To explain the results obtained, a mesostructure evaluation through SEM scans of the samples were used. A significant influence of geometric process parameters was detected on sample mesostructure and, consequently, on sample strength.

With the decline in fossil fuels, hydrogen-based alternatives provide a reliable and clean source for sustainable energy generation. In these endeavors, photochemical splitting for hydrogen production through tandem cells has been the source of much theoretical and experimental research in science. Much focus has been placed on interfacial band gap engineering as one of the most promising routes in the generation of hydrogen.This present work explores sputtering of n-silicon to form the active electrode in a n-Si | n-TiO₂ tandem cell and investigates the effect of variations in sputtering and post sputtering treatment parameters (rapid thermal annealing and long cycle annealing) for successful deposition of crystalline Silicon. The samples were successfully characterized via Raman Spectroscopy, X-ray Diffraction and Optical Transmission Spectroscopy to ascertain prevalent crystalline order and optical band gap, under different sputtering and post-sputtering conditions. Relevant conclusions were drawn to ascertain the best possible deposition parameters of n-Si for photocatalytic water splitting.

A simple method is presented for the continuous generation of carbon nanotube forests stably anchored on stainless-steel surfaces using a reactive-roll-to-roll (RR2R) configuration. No addition of catalyst nanoparticles is required for the CNT-forest generation, the stainless-steel substrate itself being tuned to generate the catalytic growth sites. The process enables very larges surfaces covered with CNT forests having individual CNT roots anchored to the metallic ground through primary bonds. Fog water harvesting is demonstrated and tested as one potential application using long CNT-covered wires. The RR2R is performed in the gas phase, no solution processing of CNT suspensions is used contrary to usual R2R CNT-based technologies. Full or partial CNT-forest coverage provides tuning of the ratio and shape of hydrophobic and hydrophilic zones on the surface. This enables optimization of fog water harvesters for droplet capture through the hydrophobic CNT forest, and water removal from the hydrophilic SS surface. Water recovery tests using small harp-type harvesters with CNT-forest generate water capture of up to 2.2 g/cm2h under ultrasound-generated fog flow. The strong CNT root anchoring on the stainless steel surfaces provides opportunities for (i) robustness and easy transport of the composite structure, (ii) chemical functionalization and/or nanoparticle decoration of the structures, and opens the road for a series of applications on large scale surfaces, including fog harvesting.

The fusion of surface-modified steel with tungsten carbide (WC) and NiCrBSi powder through laser metal deposition has emerged as a formidable strategy for fortifying components against wear and corrosion in extreme operating environments. Meticulous selection of WC content, innovative pre-alloying techniques, and precise control of laser metal deposition profoundly influence the mechanical properties and microstructural evolution of WC-NiCrBSi coatings applied to surface-enriched commercial alloy steel (805M2, 832M13, and 827M40). These tailored coatings exhibit exceptional resilience, ideal for harsh industrial settings in Oil and gas drilling, petrochemical, and Mining sectors. Advanced materials testing techniques, including scanning electron microscopy, light optical microscopies, and microhardness testing, unveil the innate hardness attributes, with findings highlighting the unassailable fortitude of the Mixed matrix layer's side face. The amalgamation of these testing methodologies with laser metal deposition promises an unparalleled path to extend the operational lifespan of critical components in challenging working conditions. The research horizon for WC-NiCrBSi coatings remains broad, with the potential to enhance durability, operational efficiency, and cost-effectiveness across diverse applications.

Precise monitoring of different environmental parameters and contaminations during food processing and storage is a key factor for maintaining its safety and nutritional value. Thus, developing reliable, efficient, cost-effective sensor devices for these purposes is of utmost importance. In this paper, we show that Poly-(diallyl-dimethylammonium chloride)/reduced Graphene oxide (PDAC/rGO) films produced by a simple Layer-by-Layer deposition can be effectively used to monitor temperature, relative humidity and the presence of volatile organic compounds as indicators for spoilage odors. At the same time, they show potential for electrochemical detection of organophosphate pesticide dimethoate. By monitoring the resistance/impedance changes during temperature and relative humidity variations or upon the exposure of PDAC/rGO films to methanol, good linear responses were obtained in the temperature range of 10-100 °C, 15-95 % relative humidity, and 35 ppm - 55 ppm of methanol. Moreover, linearity in the electrochemical detection of dimethoate is shown for the concentrations in the order of 102 µmol dm−3. The analytical response to different external stimuli and analytes depends on the number of layers deposited, affecting sensors’ sensitivity, response and recovery time, and long-term stability. The presented results could serve as a starting point for developing advanced multimodal sensor devices and sensor arrays with high potential for analytical applications in food safety and quality monitoring.

Despite huge effort has been devoted to the design of the initiators and reaction conditions, it remains challenging to synthesize high molecular weight polypeptides with conventional solution phase synthesis. In this work, surface-initiated vapor deposition polymerization (SI-VDP) was utilized to graft synthetic polypeptides poly (γ-benzyl L-glutamate) (PBLG) from polystyrene (PS) resin beads by ring-opening polymerization of N-carboxyanhydrides (NCAs). It was demonstrated for the first time that high molecular weight bulk PBLG (> 500,000) could be readily obtained within one hour via solvent-free synthetic method which paves the way for the synthesis of copolypeptides with high molecular weight.

Compressive residual stresses in thin films can inhibit crack propagation under normal or sliding contact loading, with associated enhancement of the coating apparent toughness, load bearing capacity and wear resistance. This study investigates the influence of residual stress distributions on the thin film/substrate adhesion using a nanoindenter coupled with scanning electron microscope (SEM) investigations of indentation induced failure modes. Reactive and un-reactive magnetron sputtering with ion plating was used to coat a (100) silicon substrate with aluminum nitride (AlN) with and without an aluminum (Al) adhesion layer. The presence of an Al bond layer gives additional interfacial tensile stress because of the difference in thermal expansion coefficient. Additionally, a different magnitude of residual stresses in the AlN coating was achieved by changing the applied bias voltage onto the substrate. Wafer curvature method and incremental focused ion beam (FIB) milling, combined with high-resolution in situ scanning electron microscopy (SEM) imaging and full field strain analysis by digital image correlation (DIC), were used to measure the average and in-depth stress residual stress distribution in the produced coatings. The adhesion energy was then quantified by using a nanoindentation based model. Results demonstrate that the additional tensile residual stress in the aluminum adhesion layer decrease significantly the coating adhesion, even in presence of a higher compressive stress state in the AlN top-layer. Therefore, the coatings without Al-layer showed better adhesion because of a more homogeneous compressive residual stress in comparison with the coating having Al layer, even though both groups of coatings are produced under same bias voltage. Results are discussed, and some general suggestions are made on the correlation between coating/substrate property combination and the adhesion energy of multilayer stacks. The results suggested that Al bond-layer and inhomogeneous residual stresses affected the adhesion of AlN negatively to a substrate like silicon.

A controlled ammonia (NH₃) release experiment was performed at a grassland site to quantify the effect of dry deposition, at the field scale between the source and the receptors (NH₃ measurement locations), on the estimates of emission rates by means of inverse dispersion modelling. NH₃ was released for 3 hours at a constant rate of Q = 6.29 mg s⁻¹ from a grid of 36 orifices spread over an area of 250 m². The increase in line-integrated NH₃ concentration was measured with open-path optical miniDOAS devices at different locations downwind of the artificial source. Using a backward Lagrangian stochastic (bLS) dispersion model (bLSmodelR), the fraction of the modelled release rate to the emitted NH₃ (Q_bLS/Q) was calculated from the measurements of the individual instruments. Q_bLS/Q was found to be systematically lower than 1, on average between 0.69 and 0.91, depending on the location of the receptor. We hypothesized that NH₃ dry deposition to grass and soil surfaces was the main factor responsible for the observed depletion of NH₃ between source and receptor. A dry deposition algorithm based on a deposition velocity approach was included in the bLS modelling. Model deposition velocities were evaluated from a ‘big‑leaf’ canopy resistance analogy. Canopy resistances (generally termed Rc) that provided Q_bLS/Q = 1 ranged from 75 to 290 s m⁻¹, showing that surface removal of NH₃ by dry deposition can plausibly explain the original underestimation of Q_bLS/Q. The inclusion of a dry deposition process in dispersion modelling is crucial for emission estimates, which are based on concentration measurements of depositing tracers downwind of homogeneous area sources or heterogeneously distributed hot spots, such as e.g. urine patches on pastures in the case of NH₃.

Fatty acids (FAs) represent an important class of metabolites, impacting on membrane building blocks and cellular regulatory networks. In nature, prokaryotes are characterized with the most impressing FA structural diversity and the highest relative contents of free fatty acids (FFAs). Thereby, nitrogen-fixing bacteria (order Rhizobiales), often found in symbiosis with legumes, attract a special interest. Indeed, FAs impact on the structure of rhizobial nodulation factors, required for successful infection of plant root. Although the FA patterns can be addressed by GC- and LC-MS, these methods are time-consuming and suffer from compromised sensitivity, low stability of derivatives and artifacts. In contrast, MALDI-TOF-MS represents an excellent platform for high-efficient metabolite fingerprinting, also applicable to FFAs. Therefore, here we propose a simple and straightforward protocol for high-throughput relative quantification of FFAs in rhizobia by the combination of Langmuir technology and MALDI-TOF-MS, which is featured with high sensitivity, accuracy and precision of quantification. Here we propose a step by step procedure comprising rhizobia culturing, pre-cleaning, extraction, sample preparation, mass spectrometric analysis, data processing and post-processing. To demonstrate the analytical potential of the protocol we illustrate it by a case study – comparison the FFA metabolomes of two rhizobia species - Rhizobium leguminosarum and Sinorhizobium meliloti.

Structural self-organizing and pattern formation are universal and key phenomena observed during growth and cluster-assembling of the carbyne-enriched nanostructured metamaterials at the ion-assisted pulse-plasma deposition. Fine tuning these universal phenomena opens access to designing the properties of the growing carbyne-enriched nano-matrix. The structure of bonds in the grown carbyne-enriched nano-matrices can be programmed by the processes of self-organization and auto-synchronization of nanostructures. We propose the innovative concept, connected with application of the universal Cymatics phenomena during the predictive growth of the carbyne-enriched nanostructured metamaterials. We also propose the self-organization approach for increase stability of the long linear carbon chains. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon and their distribution by the spatial structure and properties of the nanostructured metamaterial grows region through the new synergistic effect. Mentioned effect will be provided through the vibration-assisted self-organized wave patterns excitation along with simultaneous manipulating by their properties through the electric field. We propose to use acoustic activation of the plasma zone of nano-matrix growing. Interaction between the inhomogeneous electric field distribution generated on the vibrating layer and the plasma ions will serve as the additional energizing factor controlling the local pattern formation and self-organizing of the nano-structures. Suggested concept makes it possible to provide precise predictive designing the spatial structure and properties of the advanced carbyne-enriched nanostructured metamaterials.

A new generation of nano-technologies is expanding solid propulsion capabilities and increasing their relevance for versatile and manoeuvrable micro-satellites with safe high-performance propulsion. We propose the innovative concept, connected with application of new synergistic effect of the energetic materials performance enhancement and reaction zones programming for the next generation small satellite multimode solid propulsion system. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon, by the properties of the energetic materials reaction zones and by localization of the energy release areas. This synergistic effect can be provided through application of the functionalized carbon-based nanostructured metamaterials as a nano-additives along with simultaneous manipulating by their properties through the electrostatic field. Mentioned effect will be controlled through predictive programming both by the spatial structure and physics-chemical properties of the functionalized carbon-based nano-additives and through the electromagnetic control of the self-organized wave pattern excitation and micro- and nano- scale oscillatory networks in the energetic material reaction zones. Suggested new concept makes it possible to increase the energetic material regression rate and increase the thrust of the solid propulsion system with minimal additional energy consumption.