The cities of the future are places of sustainable mobility and a continuous reduction in the amount of harmful substances entering the surrounding environment. Current emission models are mainly dedicated to fully combustion vehicles and do not fully reflect the actual emissions of vehicles in the fleet, which is becoming increasingly diverse. The increasing share of hybrid and electric vehicles is generating the need to measure emissions and energy consumption from these vehicles and to develop new emission models that are accurate. This problem mainly concerns low-emission zones in cities, where mobility planning should be based on simulation models that are based on a continuously updated database. This work concerns the proposal of a two-dimensional model of emissions from hybrid vehicles using artificial neural networks for low-emission zones. The results can be used to further develop such emission models.

The key to ensuring the sustainability of transportation operations on the roads is to manage traffic flows homogeneously. By homogenizing the behavior of various drivers, traffic operation can be optimized, and traffic safety can be improved. However, the advent of autonomous vehicles is expected to have a major impact on the homogeneity of sustainable transportation operations. In this study, a method of driving in harmony with surrounding vehicles was studied to minimize the impact of autonomous vehicles on current traffic operation. In particular, in this study, a methodology was developed to optimize the driving behavior of autonomous vehicles by analyzing the driving behavior of following vehicles using spectrum analysis. Specifically, a method for calculating three indicators that can analyze the driving behavior of a following vehicle, such as reaction time, stimulus adaptation index, and collision risk avoidance index, was proposed. These indices produced consistent and robust results for all traffic conditions. If these indicators are used, it is expected that sustainable traffic management will be possible even when autonomous vehicles and human drivers are mixed on the road.

Road dust resuspension, especially the particulate matter fraction below 10 µm (PM10), is one of the main air quality management challenges in Europe. Road dust samples were collected from representative streets (suburban and urban) of the city of Viana do Castelo, Portugal. PM10 emission factors (mg veh-1 km-1) ranging from 49 (asphalt) to 330 (cobble stone) were estimated by means of the United Stated Environmental Protection Agency method. Two road dust fractions (< 0.074 mm and from 0.0074 to 1 mm) were characterised for their geochemical, mineralogical and morphological properties. In urban streets, road dusts reveal the contribution from traffic emissions, with higher concentrations of e.g. Cu, Zn, and Pb. In the suburban area, agriculture practices likely contributed to As concentrations of 180 mg kg-1 in the finest road dust fraction. Samples are primarily composed of quartz, but also of muscovite, albite, kaolinite, microcline, Fe-enstatite, graphite and amorphous content. Particle morphology clearly shows the link with natural and traffic related materials, with well-formed minerals and irregular aggregates. The hazard quotient suggests a probability to induce non-carcinogenic adverse health effects in children by ingestion of Zr. Arsenic in the suburban street represents a human health risk of 1.58 x 10-4.

IoT is a new communication paradigm that gains a very high importance in the past few years. This communication paradigm supports various heterogeneous applications in many fields and with the dramatic increase of the number of sensor devices, it becomes a demand. Designing IoT networks faces many challenges that include security, massive traffic, high availability, high reliability and energy constraints. Thus, new communication technologies and paradigms should be deployed for IoT networks to overcome these challenges and achieve high system performance. Distributed computing techniques (e.g. fog and MEC), software defined networking (SDN), network virtualization and blockchain are common recent paradigms that should be deployed for IoT networks, either combined or individually, to achieve the main requirements of the IoT networks at a high system performance. Fog computing is a form of edge computing that has been developed to provide the computing capabilities (e.g. storage and processing) at the edge of the access network. Employing Fog computing in IoT networks, as an intermediate layer between IoT devices and the remote cloud, becomes a demand to make use of the edge computing benefits. In this work, we provide a framework for the IoT system structure that employs an edge computing layer of Fog nodes controlled and managed by SDN network with the blockchain technology to achieve a high level of security for latency sensitive IoT applications. The proposed system employs SDN network with distributed controllers and distributed OpenFlow switches; these switches are enabled with limited computing and processing capabilities. Furthermore, a data offloading algorithm is developed to allocate different processing and computing tasks to the distributed OpenFlow switches with available resources. Moreover, a traffic model is proposed to model and analyze the traffic among different parts of the network. The proposed work achieves various benefits to the IoT network, such as the latency reduction, security improvement and high efficiency of resources utilization. The proposed algorithm is simulated and also the proposed system is experimentally tested over a developed testbed to validate the proposed structure. Experimental results show that the proposed system achieves higher efficiency in terms of latency, security and resource utilization.

Autonomous vehicles (AVs) may not only reduce parking demand, but also free up on-street parking spaces. From the perspective of bus priority, converting on-street parking lots into dedicated bus lanes can both ensure bus priority and accommodate non-bus traffic, helping to reduce congestion and pollution. In order to study the impact of conversion of on-street parking lots to bus lanes on traffic flow, a microscopic simulation framework based on VISSIM is proposed in this paper. Data was collected using the floating car method and video recording method to quantify the factors affecting traffic flow due to the conversion of on-street parking. The VISSIM simulation model was then calibrated. According to the proportion of the on-street parking lots into a bus lane, the on-street parking lots conversion simulation model of different scenarios was established, and the influence of different on-street parking lots conversion ratio on traffic efficiency and pollution emission was quantitatively analyzed. Finally, the optimization method based on bus lane network connectivity is discussed. The results indicate that: When the on-street parking lots conversion ratio is approximately 100%, bus speed increases by 21.03%, bus delays decrease by 14.27%, and bus parking instances decrease by 11.31%. Total emissions are negatively correlated with vehicle speed. As the conversion rate of on-street parking increases, the emissions of road segments and the entire road network gradually decrease. At a conversion ratio of 100%, the average total emissions for road segments have the highest reduction rate, decreasing by 4.12%. At a conversion ratio of 50%, the average emission total for the road network shows the largest reduction, falling by 2.88%.

Background and Objectives: In recent years, electric scooters have gained widespread popularity as an easy and affordable mode of transport in urban areas worldwide. Simultaneously, trauma centres have observed an increasing number of associated injuries to users. While injury patterns associated with other vehicles are now well-researched, electric scooter-related injuries are a new topic in the literature. Our study aims to investigate the disparities in injury patterns and other critical accident characteristics among bicycle, electric scooter, and scooter riders. Materials and Methods: In this one-year prospective observational study, we examined patients who sustained injuries while riding bicycles, electric scooters, or scooters between April 2021 and March 2022 at Hungary's largest trauma centre in Budapest. During this one-year period, we identified 1938 patients, 1378 cyclists, 370 electric scooters and 190 scooter users. We collected basic demographic information, recorded injury type and severity, time of day the injury occurred, and alcohol intoxication. Results: While 4.6% of cyclists and 5.8% of scooter riders had consumed alcohol, 26.8% of electric scooter riders were intoxicated at the time of their accident. 45.8% of electric scooter-related injuries occurred at night, compared to only 9.2% and 14.1% of bike and scooter-related injuries, respectively. Sober patients were more likely to suffer mild and severe limb injuries (Odds Ratio (OR): 3.85, P = .0001 and OR: 3.26, P = .0001), but less likely to experience mild and severe head injuries (OR: 0.1, P = .0001 and OR: 0.25, P = .0001) than intoxicated patients. Cyclists had significantly fewer cases of severe head trauma than those injured while using electric scooters (OR: 0.34, P = .0166). Conclusions: Severe craniofacial injuries are more common in intoxicated patients and in patients injured using electric scooters.

rdinary people and political leaders must know the sources of greenhouse gas emissions and their effect on global climate change before they have ability to make decisions to reduce emissions and increase sinks of these gases. These people must, however, understand where greenhouse gas emissions are formed and how reductions can be made: they must understand where carbon dioxide sinks are and how to preserve or increase these sinks. North Savo is the example used in this work to describe the present emissions and sinks. There are proposals on what should and could be done to reduce greenhouse gas emissions caused by traffic, heating, forests and agriculture. There are possibilities of reducing emissions of greenhouse gases in traffic and heating in spite of the fact that the province has a low population density with long distances between homes and workplaces and schools, and a cold climate. We believe that research will also find solutions for reducing greenhouse gases and protecting waters, which are used for recreational purposes and for raw water of drinking water in many places. Luckily forests cover large areas of North Savo and their growth is an important carbon dioxide sink. In addition, forest soils serve as a valuable storage of carbon. Besides carbon dioxide emissions, emissions of nitrous oxide and methane must also be considered since they are more potent greenhouse gases than carbon dioxide and land use can thus influence these gas emissions.

The objective of the study was to report the health-related quality of life (HRQOL) following road traffic accidents (RTAs) among children. A community-based survey using EuroQol five-dimension questionnaire (EQ-5D-5L) in Hindi was used to collected data from community. The survey included 2620 households from urban and rural areas of Ujjain, India. From these households 229 children aged 5–18 years with a history of RTA in the last 1 year were identified, with 27%, 63%, and 10% children reporting mild, moderate, and severe injury based on length of hospitalization. Motorcycles, bicycles, and pedestrians constituted most RTAs. Helmet use was low (12%). EQ-5D-5L revealed that the most severe and extreme problem was pain and discomfort, whereas the least severe problem was usual activity and self-care. The most common (65%) injuries were either abrasion or fracture and dislocation. EQ-5D-5L severity index was maximum (mean 72) for lower extremity injuries. The results of the present study highlight the ability and requirement for quality of life measurement using EQ-5D-5L among children post-RTA.

The International Maritime Organization (IMO) is enforcing increasingly stringent regulations on ship carbon emissions, The International Maritime Organization (IMO) has been implementing progressively strict regulations on ship carbon emissions, leading to the adoption of the virtual arrival (VA) method by many vessels to reduce their carbon footprint. However, the effectiveness of the traditional VA method often varies in busy ports with complex traffic organization scenarios. To address this, our study presents a novel, comprehensive model that integrates vessel scheduling with the VA approach. This model is designed to achieve a dual objective: reducing carbon emissions through Virtual Arrival and simultaneously minimizing vessel waiting times. In addition to these goals, it incorporates essential aspects of safety, efficiency, and fairness in port management, utilizing the NSGA-2 algorithm to find optimal solutions. This model has been tested and validated through a case study at Ningbo-Zhoushan port, employing its dataset. The results demonstrate that our innovative model and algorithm significantly outperform traditional scheduling methods, such as First-Come-First-Serve (FCFS) and Virtual-Arrival Last-Serve (VALS), particularly in terms of operational efficiency and reduction in vessel carbon emissions.

Studying and understanding the behavior of people and vehicles on public roads can be of utmost importance for supporting the activities of many institutional stakeholders. It may allow automated supervision of the ongoing situation in a given place, with warnings or alarms raised in case of anomalies. It may be used to plan their interventions on road and town organization. It may provide them with advanced support to decision-making. The number of involved entities and places to manage makes it infeasible to manually handle all the traffic-related tasks. Moreover, the complexity of the tasks to be carried out requires the adoption of advanced approaches. Many AI solutions are nowadays mature to support these requirements. In some cases, the motivations and objectives of traffic management require the AI outcomes to be understandable, interpretable and explainable. In this paper, we propose TrAnSIT (TRaffic ANalysis Supervision and Interpretation Tool), an AI-based framework that combines several modules, each aimed at tackling a specific traffic-related task, so as to cover a wide landscape of traffic-related issues, from overall urban or suburban traffic management to surveying specific road segments that fall under the scope of one camera. Most of these modules are based on AI techniques that support a human-level understanding of the outcomes.

This paper focuses on robust multi-criteria traffic network equilibrium problems with path capacity constraints. The concepts of robust vector equilibrium and robust vector equilibrium with respect to worst case are introduced, respectively. To generate a subset of robust vector equilibrium, an equivalent min-max optimization problem is constructed. In addition, a direct search algorithm, in which the step size without derivatives and redundant parameters, for solving this min-max problem is proposed. To find a subset of robust vector equilibrium with respect to worst case, an equivalent smoothing optimization problem based on a variant version of ReLU activation function is established. Numerical experiments are also presented to expound the advantages of the algorithms.

The analogy between the theory of phase transitions in simple fluids and vehicular traffic flow has long been suspected, promising a new level of understanding of urban congestion by standing on one of the firmer foundations in physics. The obstacle has been the interpretation of the thermal energy of the gas-particle system, which remains unknown. This paper proposes the flow of cars through the network as a viable interpretation, where the fundamental diagram for traffic flow would be analogous to the coexistence curve in gas-liquid phase transitions. Thanks to the power-law form of the coexistence curve, it was possible to formalize that the resulting network traffic model belongs to the Kardar-Parisi-Zhang universality class. The scaling relationships arising in this universality class are found to be consistent with West's scaling theory for cities. It is shown that congestion costs (delays + fuel consumption) scale superlinearly with city population, possibly and worryingly more so than predicted by West's theory. Implications for sustainability and resiliency are discussed.

Exposure to traffic-related air pollution is linked with acute alterations in blood pressure (BP). We examined the cumulative short-term effect of black carbon (BC) exposure on systolic (SBP) and diastolic (DBP) BP and assessed effect modification by participant characteristics. SBP and DBP were repeatedly measured on 152 traffic enforcers. Using a linear mixed-effects model with random intercepts, quadratic (QCDL) and cubic (CCDL) constrained distributed lag models were fitted to estimate the cumulative effect of BC concentration on SBP and DBP during the 10-hours (daily exposure) and 7-days (weekly exposure) before the BP measurement. Ambient BC was related to increased BP with QCDL models. An interquartile range change in BC cumulative during the 7-days before the BP measurement was associated with increased BP [1.2% change in mean SBP, 95% confidence interval (CI), 0.1 to 2.3; and 0.5% change in mean DBP, 95% CI, –0.8 to 1.7]. Moreover, the association between the 10-hours cumulative BC exposure and SBP was stronger for females (4.0% change, 95% CI: 2.1–5.9) versus males, and for obese (2.9% change, 95% CI: 1.0–4.8) vs. non-obese traffic enforcers. Short-term cumulative exposure to ambient traffic-related BC could bring about cardiovascular diseases through mechanisms involving increased BP.

This paper incorporates the definition of Intrusion Detection Systems and the methodologies utilised by these systems. As well as this, this research paper also encompasses a taxonomy and a survey of IDS and the specific strategies and principles. Finally, this paper also includes a discussion amongst other authors for instance what the authors differ and agree on, along with the previously related studies.

The urbanisation phenomenon and related cities expansion and transport networks entail preventing the increase of population exposed to environmental pollution. Regarding noise exposure, the Environmental Noise Directive demands on main metropolis to produce noise maps. While based on standard methods, these latter are usually generated by proprietary software and require numerous input data concerning, for example, the buildings, land use, transportation network and traffic. The present work describes an open source implementation of a noise mapping tool fully implemented in a Geographic Information System compliant with the Open Geospatial Consortium standards. This integration makes easier at once the formatting and harvesting of noise model input data, cartographic rendering and output data linkage with population data. An application is given for a French city, which consists in estimating the impact of road traffic-related scenarios in terms of population exposure to noise levels both in relation to a threshold value and level classes.

According to the characteristics of the sustainable development of subway traffic, the establishment process of an evaluation index system is determined, and the evaluation method and basis are defined. The evaluation index system is established from the aspects of subway traffic sustainability, economic sustainability and urban coordination sustainability. The comprehensive evaluation method of the analytic hierarchy process (AHP) model is used to calculate the weights of comprehensive evaluation indexes at each level. Finally, the sustainable development model of Shijiazhuang subway traffic is evaluated. The results show that the proposed evaluation system and model reflect the degree of sustainable development of subway traffic and can be used for reference in the evaluation of regional subway traffic sustainable development.

Traffic source emissions inventories for the rapidly growing West African urban cities are necessary for better local characterization of vehicle emissions released into these cities atmosphere. This study based on local field campaign in a representative site of anthropogenic activities over West African cities such as Yopougon (Abidjan, Côte d'Ivoire) during 2016, provided useful information on vehicle type and age, traveling time, fuel type and amount for fuel consumption estimation. Also, high traffic flow of personal car were recorded on highway, boulevard and backstreet whereas high flows of intra-communal sedan taxi are recorded on main and secondary roads. In addition, the highest daily fuel consumption value of 56 L.day^-1 was recorded in heavy vehicle while the lowest value of 15 L.day^-1 is recorded for personal car using gasoline. This study will be useful for the improvement of uncertainties related to the different databases used to estimate inventories emissions either national or international reports. This work provides useful information for future studies on urban air quality, climate and health impacts assessment in African cities. It may also be useful for policy makers to support implementation of emission reduction policy in West African cities.

By 2020, over 100 countries expanded electric and plug-in hybrid electric vehicle (EV/PHEV) technologies, with global sales surpassing 7 million units. Governments are adopting cleaner vehicle technologies due to proven environmental and health implications of internal combustion engine vehicles (ICEVs), evidenced by the recent COP26 meeting. This article proposes an agent-based model of vehicle activity as a tool for quantifying energy consumption by simulating a fleet of EV/PHEVs within an urban street network at various spatio-temporal resolutions. Driver behaviour plays a significant role in fuel consumption, thus, simulating various levels of individual behaviour enhancing heterogeneity should provide more accurate results of potential energy demand in cities. The study found that 1) energy consumption is lowest when speed limit adherence increases (low variance in behaviour) and is highest when acceleration/deceleration patterns vary (high variance in behaviour) and 2) on average, for tested vehicles, EV/PHEVs were £116.33 cheaper to run than ICEVs across all experiment conditions. The difference in the average fuel costs (electricity and petrol) shrinks at the vehicle level as driver behaviour is less varied (more homogeneous). This research should allow policymakers to quantify the demand for energy and subsequent fuel costs in cities.

Abstract: Botnets pose a grave cybersecurity threat, enabling widescale malicious activities through networks of compromised devices. Detecting botnets is challenging given their frequent use of evasion techniques like encryption. Traditional signature-based methods fail against modern botnets capable of zero-day attacks. This paper surveys recent advances applying machine learning for botnet detection based on analysis of network traffic payloads, flows, DNS data, and hybrid feature fusion. Core machine learning models include support vector machines, neural networks, random forests, and deep learning architectures, which extract patterns to separate benign and botnet behaviors automatically. Results demonstrate machine learning's capabilities in identifying heterogeneous botnets using artefacts in network streams. However, challenges remain around limited labeled data, real-time streaming, adversarial evasion, and model interpretability. Promising directions involve semi-supervised learning, adversarial training, scalable analytics, and explainable AI to address these gaps. Beyond the technical aspects, responsible development and deployment of botnet detection systems raise ethical considerations around privacy, transparency, and accountability. With diligent cross-disciplinary collaboration, machine learning promises enhanced, generalizable, and trustworthy techniques to combat the serious threat posed by continuously evolving botnets across the digital ecosystem.

This study investigates the application of Light Detection and Ranging (LiDAR) sensor technology for data collection at signalized intersections characterized by a high rate of traffic crashes. The research aims to provide valuable insights into the potential of LiDAR-based data analysis to enhance road safety and traffic management at signalized intersections. The research methodology involved the deployment of LiDAR sensors at Marlboro Pike & Brooks Dr. signalized intersection in Coral Hills, Maryland. Two LiDAR sensors installed in this intersection to collect high-resolution, three-dimensional data of the intersection area from June, 1^st to July, 7^th 2023. The data included information on vehicle trajectories, speeds, and behaviors, as well as pedestrian and cyclist movement patterns. Concurrently, historical traffic crashes recorded and traffic flow data were obtained for the same intersection.The analysis of LiDAR data involved several key aspects including LiDAR data allowed for a precise evaluation of traffic flow patterns, including congestion points, traffic volume fluctuations, and peak-hour behavior. This information provided insights into potential factors contributing to crashes. By analyzing LiDAR data, the study identified near-miss incidents, which are often precursors to actual crashes. This proactive approach could assist in identifying crash-prone areas within the intersection. The LiDAR data analysis also focused on pedestrian and cyclist movements, including jaywalking and bike lane usage. The aim was to identify areas where infrastructure improvements could enhance safety for vulnerable road users. LiDAR data was compared with historical crash data to identify specific locations within the intersection that exhibited a high frequency of crashes. This information can guide targeted safety interventions. Last but not least, the study explored opportunities to optimize traffic signal timings based on real-time traffic data from LiDAR. Adaptive signal control could help mitigate congestion and reduce the risk of crashes.The results of this study demonstrated the potential of LiDAR sensor technology in collecting detailed data for traffic analysis in signalized intersections. By combining LiDAR data with historical crash records and traffic flow data, traffic engineers and urban planners can develop evidence-based strategies to reduce the frequency and severity of crashes in high-risk areas. Ultimately, this research contributes to a comprehensive understanding of how LiDAR technology can be employed to enhance road safety and traffic management, providing valuable insights for traffic engineers, urban planners, and policymakers seeking to improve the safety and efficiency of signalized intersections with a history of high traffic crashes.

Single and multi-vehicle crashes are a significant issue that causes economic and social costs and has therefore gained attention. This study explored the factors associated with injury severity for both single- and multi-vehicle crashes using over 550,000 crash data points in Japan between 2019 and 2021. We identified the determinants of road infrastructure and traffic control while controlling for driver, vehicle, environmental, and accident characteristics by applying ordered logit and bias-reduced binomial regression models. Our findings are as follows. 1) Traffic control variables did not affect single-vehicle crashes. 2) Guardrails had a higher severity in both single-vehicle crashes and multi-vehicle crashes at intersections. 3) The impact of the centerline differed between intersections and non-intersections for multi-vehicle crashes.  These results of this study provide transportation agencies with important guidance as to the road infrastructure and transport control.

The exponential growth of digital media content has introduced new challenges in managing and classifying internet traffic. Digital media traffic is composed of various applications such as video, audio, social media, and search, and its data structure is complex, incorporating a vast array of features. The classification of traffic data is a crucial aspect of internet traffic management and network security, and it forms the basis for several scenarios, including content distribution, advertising recommendations, and data analysis. Traditional classification methods rely mainly on deep packet inspection and port-based techniques, which have become increasingly ineffective due to the rapid evolution of network traffic. To address this issue, this study proposes a machine learning-based traffic classification method aimed at enhancing the accuracy and efficiency of digital media traffic classification to meet the current needs of traffic management and network security. The paper also analyzes and evaluates the classification effect and prediction capability of various algorithms under different training set sizes to validate the feasibility and effectiveness of the proposed method. The result demonstrates that the neural network algorithm has superior classification and prediction capabilities compared to the decision tree and support vector machine algorithms. Furthermore, our proposed method achieves the highest accuracy of 96.88% with a large training sample of 40,000 data streams, proving its superiority in handling high-dimensional data and complex datasets. The research results are significant for the development of digital media traffic classification and prediction methods and are expected to be applied in practical scenarios.

An exact solution for the Nagel-Schreckenberg model for v_max = 1 is known since the 90s, yet for v_max > 1 it remains an open question. It is conjectured here that this general solution can be generated from the basic solution (for v_max = 1) by a linear coordinate transformation, the shear mapping, which requires no additional parameters in the deterministic case, and two additional parameters otherwise. The proposed solutions show remarkable agreement with existing numerical solutions, except in the congested regime where the Monte Carlo data shows more concavity than the more linear congested branches predicted by the theory. More research is needed to investigate this bias.

Research on Traffic Light Recognition (TLR) has grown in recent years, primarily driven by the growing interest in autonomous vehicles development. Machine Learning algorithms have been widely used to that purpose. Mainstream approaches, however, require large amount of data to properly work, and as a consequence, a lot of computational resources. In this paper we propose the use of Expert Instruction (IE) as a mechanism to reduce the amount of data required to provide accurate ML models for TLR. Given an image of the exterior scene taken from the inside of the vehicle, we stand the hypothesis that the picture of a traffic light is more likely to appear in the central and upper regions of the image. Frequency Maps of traffic light location were thus constructed to confirm this hypothesis. The frequency maps are the result of a manual effort of human experts in annotating each image with the coordinates of the region where the traffic light appears. Results show that EI increased the accuracy obtained by the classification algorithm in two different image datasets by at least 15%. Evaluation rates achieved by the inclusion of EI were also higher in further experiments, including traffic light detection followed by classification by the trained algorithm. The inclusion of EI in the PCANet achieved a precision of 83% and recall of 73% against 75.3% and 51.1%, respectively, of its counterpart. We finally presents a prototype of a TLR Device with that expert model embedded to assist drivers. The TLR uses a smartphone as a camera and processing unit. To show the feasibility of the apparatus, a dataset was obtained in real time usage and tested in an Adaptive Background Suppression Filter (AdaBSF) and Support Vector Machines (SVMs) algorithm to detect and recognize traffic lights. Results show precision of 100% and recall of 65%.

Abstract：Commuting of residents in big city often brings tidal traffic pressure or congestions. Understanding the causes behind this phenomenon is of great significance for urban space optimization. Various spatial big data make possible the fine description of urban residents travel behaviors, and bring new approaches to related studies. The present study focuses on two aspects: one is to obtain relatively accurate features of commuting behaviors by using mobile phone data, and the other is to simulate commuting behaviors of residents through the agent-based model and inducing backward the causes of congestion. Taking the Baishazhou area of Wuhan, a local area of a mega city in China, as a case study, travel behaviors of commuters are simulated: the spatial context of the model is set up using the existing urban road network and by dividing the area into travel units; then using the mobile phone call detail records (CDR) of a month, statistics of residents' travel during the four time slots in working day mornings are acquired and then used to generated the OD matrix of travels at different time slots; and then the data are imported into the model for simulation. By the preset rules of congestion, the agent-based model can effectively simulate the traffic conditions of each traffic intersection, and can also induce backward the causes of traffic congestion using the simulation results and the OD matrix. Finally, the model is used for the evaluation of road network optimization, which shows evident effects of the optimizing measures adopted in relieving congestion, and thus also proves the value of this method in urban studies.

Road Safety Education (RSE) is widely known as a reliable determinant of future results for what concerns health and welfare, and as an undisputable factor which contributes to the social behavior of individuals and to their mid and long-term road safety outcomes. However, its development has been relatively scarce in most countries, fact which has contributed to letting matters as delicate as traffic crashes produced by road misbehaviors continue to be a prevalent problem, thus affecting the health of the community. Objective: The aim of this study was to describe the relationship between demographic and RSE-related variables and the self-reported road risky behavior of Spanish students. Methods: For this cross-sectional study, a representative sample of 4,062 (51.5 males and 48.5% females) participants attending primary (47.5%), secondary (40.7%) and high school (11.7%) was gathered through a national survey on RSE and road behaviors. Results: A set of significant associations between demographic factors, RSE variables and self-reported road behaviors was found. Furthermore, the SEM modelling allowed us to establish that age, observed misbehaviors, attitudes towards road safety and risk perception keep a direct link with the road risky behavior of children and young people. The knowledge of traffic rules was not a significant predictor of road behavior. Conclusions: The results of this study show that, together with demographic factors such as age, RSE-related variables have an effect on the road behavior of children and young people. They also suggest the need of strengthening actions to be implemented in road safety (Road Safety Education), into scholar and community levels.

In response to growing industrial demands, necessitated by larger ships and increased cargo volumes, many port authorities worldwide are undertaking a significant expansion of their infrastructure to increase their capacity. Significant expansion raises challenges such as potential congestion and environmental concerns, especially for port located in urban area as the case study explored in this paper. To address these issues, the study employs a combination of scenario analysis developed in collaboration with the port authority and logistic system simulation. This approach assesses the capacity of existing access gates to handle the increased trucking traffic and optimizes the unloading process of construction trucks at a new terminal. Key findings suggest that while the current gate capacities are adequate, optimizing unloading times at the new terminal is critical to prevent road congestion in urban area before the gate and reduce negative impacts such as sound and atmospheric pollution. The study advocates for an appointment system during peak hours to manage traffic flow effectively and underscores the importance of collaboration between the city and port authorities in managing truck traffic to mitigate congestion on the city side. Nonetheless, the study recognizes certain constraints, including the incomplete evaluation of the influence of intermodal transport on truck traffic. Furthermore, the study emphasizes the need for future research to consider the correlation between vehicle numbers and service levels, aiming to effectively adjust the time in the system.

Background: Permanent Daylight Savings Time (DST) may improve road safety by providing more daylight in the evening but could merely shift risk to morning commutes or increase risk due to fatigue and circadian misalignment. Methods: To identify how potential daylight exposure and fatigue risk could differ between permanent DST versus permanent Standard Time (ST) or current time arrangements (CTA), generic work and school schedules in five United States cities were modeled in SAFTE-FAST biomathematical modeling software. Commute data were categorized by morning (0700-0900) and evening (1600-1800) rush hours. Results: Percent darkness was greater under DST compared to ST for the total waking day (t=2.59, p=0.03) and sleep periods (t=2.46, p=0.045). Waketimes occurred before sunrise 63%±41% percent of the time under DST compared to CTA (42%±37%) or ST (33%±38%; F(2, 74)=76.37; p<0.001). Percent darkness was greater during morning (16%±31%) and lower during evening rush hour (0%±0%) in DST compare to either CTA (morning:7%±23%; evening:7%±14%) or ST (morning:7%±23%; evening:7%±15%). Discussion: Morning rush hour overlapped with students’ commutes and shift worker reverse commutes, which may increase traffic congestion and risk compared to evening rush hour. Switching to permanent DST may be more disruptive than either switching to ST or keeping CTA without noticeable benefit to fatigue or potential daylight exposure.

Anomaly detection is an active area of research with numerous methods and applications. This survey reviews the state-of-the-art of data-driven anomaly detection techniques and their application to the the aviation domain. After a brief introduction to the main traditional data-driven methods for anomaly detection, we review the recent advances in the area of neural networks, deep learning and temporal-logic based learning. We cover especially unsupervised techniques applicable to time series data because of their relevance to the aviation domain, where the lack of labeled data is the most usual case, and the nature of flight trajectories and sensor data is sequential, or temporal. The advantages and disadvantages of each method are presented in terms of computational efficiency and detection efficacy. The second part of the survey explores the application of anomaly detection techniques to aviation and their contributions to the improvement of the safety and performance of flight operations and aviation systems. As far as we know, some of the presented methods have not yet found an application in the aviation domain. We review applications ranging from the identification of significant operational events in air traffic operations to the prediction of potential aviation system failures for predictive maintenance.

Accurate traffic simulation models play a crucial role in developing intelligent transport systems that offer timely traffic information to users and efficient traffic management. However, calibrating these models to represent real-world traffic conditions accurately poses a significant challenge due to the dynamic nature of traffic flow and the limitations of traditional calibration methods. This article introduces a machine learning-based approach to calibrate macroscopic traffic simulation models using real-time traffic video stream data. By leveraging computer vision technologies to extract key traffic parameters from video streams, the approach demonstrated a notable improvement in aligning the generated data from the calibrated simulation model with car sensor data, achieving an average improvement of over 50% compared to the uncalibrated macroscopic model. Moreover, there was a substantial reduction in data drift for the machine learning model integrated into the virtual transport space using vehicle-to-everything technology, resulting in a more than fourfold decrease in the average absolute error of the model.

Turbo-roundabouts are one of the most frequently recommended road junction design options when it comes to increasing traffic capacity and traffic safety. This is in particular true of suburban areas, with dominant traffic flow on the main road and moderate traffic flow on the side road. Other intersections handling local traffic and considerably constricting the availability of space are usually located in the vicinity of such intersections. Another factor contributing to less availability of land for construction in these locations is the presence of surrounding residential housing. Then choosing the suitable turbo-roundabout type becomes the main issue. The article presents a case study for the selection of a type of turbo roundabout under the conditions of considerably constricted land availability, based on analyses of provision of swepth path for the chosen design vehicles. The article considers the typical Egg type turbo roundabouts, "flattened" turbo roundabouts and ellipse based roundabouts, with unconventional geometries of the truck apron and central island. For each of the analysed roundabout types setting out methods were described in detail, which enable designers to quickly select a type of roundabout suitable for specific constrained site conditions.

The World Health Organization’s Health Economic Assessment Tool (HEAT) for walking and cycling is a user-friendly web-based tool to assess health impacts of active travel. HEAT, developed over 10 years ago, has been used by researchers, planners and policymakers alike in appraisals of walking and cycling policies of both national and more local scales. HEAT has undergone regular upgrades adopting the latest scientific evidence. This article presents the most recent upgrades of the tool. Health impacts of walking and/or cycling in a specified population are quantified in terms of premature deaths avoided (or caused). In addition to the calculation of benefits from physical activity, HEAT was recently expanded to include assessments of the burden associated with air pollution exposure and crash risks while walking or cycling. Further, impacts on carbon emissions from mode shift to active travel modes can now be assessed. Monetization of impacts using Value of Statistical Life and Social Costs of Carbon now uses country-specific values. As active travel inherently results in often substantial health benefits as well as not always negligible risks, assessments of active travel behaviour or policies are incomplete without considering health implications. The recent developments of HEAT make it easier than ever to obtain ballpark estimates of health impacts and carbon emissions related to walking and cycling.

As traffic congestion gets worse year by year in metropolitan areas, cities search for solutions to improve their traffic performance and reduce their environmental impacts. This paper focuses on parking pricing and congestion pricing and their short-term effects not only on traffic congestion but also on the potential revenue for a city. We develop an easy to implement multimodal macroscopic traffic and parking search model for a central area based on aggregated data at the network level. Our methodology allows us to analyze how introducing parking pricing inside a network, or a congestion toll combined with a park and ride (P+R) scheme can affect the drivers’ decision between entering the network by car (private vehicle) or using P+R instead. This decision directly influences the number of drivers using P+R, and this impacts, in turn, the traffic performance. Based on such analysis, a city can get valuable insights to evaluate whether congestion pricing is a necessity or if the traffic improvements resulting from implementing parking pricing strategies are sufficient when combined with P+R facilities. A search algorithm is used to find the best trade-off between the parking fees and the congestion toll. Any additional revenue collected through these schemes can then be used to improve public transport or the P+R facilities themselves. With minor data collection efforts and little computational costs compared to most existing parking and congestion pricing models, we illustrate our proposed framework in a case study of an area with a high parking demand for public parking spaces within the city of Zurich, Switzerland. Results show that parking pricing combined with P+R is indeed a viable option compared to congestion pricing for improving traffic performance, even if parking pricing schemes do not target all the drivers.

The paper presents data from a monthly campaign for the elemental composition of PM10 in a specific receptor Kotórz Mały (Opole Voivodeship) located in the vicinity of a moderately inhabited rural area, measured in one-hour samples with the use of the PX-375 analyzer by the Horiba company. The hourly variability of SO2, NO, NO2, CO, O3 concentrations as well as the variability of meteorological parameters were also determined. On average, during the entire measurement period, the elements related to PM10 can be arranged in the following order: As<V<Ni<Pb<Cr<Mn<Cu<Ti<Zn<K<Fe<Ca<Al<Si<S. Trace elements, including toxic elements, such as As, V, Ni, Pb, Cr, Mn, were present in low concentrations, not exceeding 10 ng/m3 (average daily value). These elements had fairly even concentrations, daily and hourly. The concentrations of the main elements in the PM10 in the receptor are subject to strong hourly changes related not only to changes in the structure of the sources identified in the statistical analysis but mainly to wind speed and direction changes (soil and sand particles pick-up and inflow of pollutants from coal combustion). It has been shown that the transport emission in the receptor can have an intense effect on PM10 in the afternoon.

The transport sector in Germany causes one-quarter of energy-related greenhouse gas emissions. One potential solution to reduce these emissions is the use of battery electric vehicles. Although a number of life cycle assessments have been conducted for these vehicles, the influence of a transport system wide transition has not been researched sufficiently. Therefore, we developed a method which combines life cycle assessment with an agent-based transport simulation and synthetic electric, diesel and gasoline powered vehicle models. We use the transport simulation to obtain the number of vehicles, their lifetime mileage and road-specific consumption. Subsequently we analyze the product systems’ vehicle production, use phase and End-of-Life. The results are scaled depending on the covered distance, the vehicle weight and the consumption for the whole life cycle. The results indicate that the sole transition of drive trains is insufficient to significantly lower the greenhouse gas emissions. However, sensitivity analyses demonstrate that there is a considerable potential to reduce greenhouse gas emissions with higher shares of renewable energies, a different vehicle distribution and a higher lifetime mileage. The method facilitates the assessment of the ecological impacts of the complete car based transportation in urban agglomerations and is able to analyze different transport sectors.

It is unclear which noise exposure time window and noise characteristics during nighttime are most detrimental for sleep quality in real life settings. We have conducted a field study with 105 volunteers wearing a wrist actimeter to record their sleep during seven days, together with concurrent outdoor noise measurements at their bedroom window. Actimetry recorded sleep latency increased by 5.6 minutes (95% confidence interval: 1.6 to 9.6 minutes) per 10 dB(A) increase in noise exposure during the first hour after bedtime. Actimetry assessed sleep efficiency was significantly reduced by 2-3 percent per 10 dB(A) increase in measured outdoor noise (Leq, 1h) for the last three hours of sleep. For subjectively reported sleepiness, noise exposure during the last hour prior to wake up was most crucial with an increase in the sleepiness score of 0.31 units (95% CI: 0.08 to 0.54) per 10 dB(A) Leq,1h. Associations for estimated indoor noise were not more pronounced than for outdoor noise. Considering noise events in addition to equivalent sound pressure levels (Leq) only marginally improved the statistical models. Our study provides evidence that matching the nighttime noise exposure time window to the individual’s diurnal sleep-wake pattern results in a better estimate of detrimental nighttime noise effects on sleep. We found that noise exposure at the beginning and the end of the sleep is most crucial for sleep quality.

This study explores the intricate relationship between the angle of vehicle-to-vehicle (V2V) conflicts and the severity of conflicts at signalized intersections during traffic signal failures, leveraging the advanced capabilities of LiDAR sensor technology. The research delves into the impact of conflict angles on collision outcomes and introduces LiDAR as a novel and precise tool for capturing spatial dynamics during unregulated traffic movements. Findings reveal that as the angle of V2V conflicts increases, indicating a wider approach between vehicles, the severity of conflicts tends to decrease. This reduction in severity is attributed to the detailed spatial data provided by LiDAR, enabling the identification of glancing impacts rather than direct head-on collisions. The mitigation of forces involved in collisions at increased angles contributes to a decreased likelihood of severe consequences, such as extensive vehicle damage and serious injuries to occupants.Conversely, as the angle of V2V conflicts decreases, signifying a narrower approach between vehicles, the potential for severe collisions tends to increase. LiDAR technology facilitates precise measurements of spatial coordinates and temporal dynamics, revealing that collisions occurring at smaller angles involve more direct and concentrated impact forces. This heightened risk of extensive damage to vehicles and increased injury severity is crucially captured by LiDAR, providing valuable insights into the relationship between conflict angles and collision outcomes during traffic signal failures. This study underscores the efficacy of LiDAR sensor technology in understanding the nuanced dynamics of V2V conflicts and highlights its role in developing targeted safety interventions. The integration of LiDAR data into traffic safety analyses offers a sophisticated approach to mitigating the impact of conflicts and enhancing overall safety at signalized intersections during signal failures. The research also highlighted that as the angle of V2P conflicts widens, PET experiences a proportional increase. A larger conflict angle signifies a more complex interaction between vehicles and pedestrians, leading to prolonged PET values. Conversely, a decrease in the angle of V2P conflicts is associated with a reduction in PET during traffic signal failures.The study commences with an examination of traffic characteristics at the E Cold Spring Ln – Hillen Rd intersection in Baltimore City, MD, utilizing a deployed LiDAR sensor. When the signal at this intersection experienced a temporary malfunction on a regular working day in September 2023, the LiDAR captured data related to vehicle and pedestrian volumes, as well as V2V and V2P conflicts. The primary objective of the research is to evaluate the repercussions of traffic signal failures on both traffic flow and safety, specifically V2V and V2P conflicts, occurring during periods of improper signal functionality. Additionally, this investigation delves into various factors that impact traffic signal performance, encompassing traffic demand, geometric layout, pedestrian interactions, and the incorporation of emerging technologies.

(1) Background: Pedestrian injuries (PIs) represent a significant proportion of road traffic injuries. We aimed at investigating the incidence and mortality of PIs in different age groups and Socio-demographic Index (SDI) categories between 1990 and 2017. (2) Method: Estimates of age-standardized incidence and mortality along with trends of PIs by SDI levels were obtained from the Global Burden of Disease from 1990 to 2017. We also calculated forecasts until 2040. (3) Results: Globally, PIs incidence increased by 3.31% (–9.94 to 16.56) in 2017 compared to 1990. Men have a higher incidence of PIs than women. Forecasted incidence was 132.02 (127.37 to 136.66) per 100,000 population in 2020, 101.52 (65.99 to 137.05) in 2030 and reduced further to 71.02 (10.62 to 152.65) by 2040. Globally across all SDI categories, there was a decreasing trend in mortality due to PIs with the global estimated percentage reduction of 37.12% (–45.19 to –29.04). (4) Conclusions: The results show that PIs are still a burden for all SDI categories despite some variation. Although incidence and mortality are expected to decrease globally, some SDI categories may require particular attention in addition to specific vulnerable age groups. Further studies addressing incidence and mortality patterns in vulnerable SDI categories are needed.

A very high parking occupancy can negatively influence the traffic performance of an area by causing very long cruising times. A very low parking occupancy, on the other hand, is inefficient from a space utilization perspective. Thus, this paper proposes a framework to compute the optimal parking occupancy rate over a given time horizon based on a macroscopic traffic and parking model. This rate is set high enough to ensure an efficient usage of the parking infrastructure. However, it should also guarantee a high likelihood of finding parking in order to eliminate the drivers’ time wasted in cruising for parking and the added congestion it causes. The model outputs are based on small data collection efforts and low computational costs, and they can be generated without complex simulation software using a simple numerical solver. Multiple vehicle types are included into our methodology allowing us to generate insights about the optimal parking occupancy with or without differentiated parking (i.e., parking for specific vehicles, such as fuel and electric vehicles). In times of a modal shift towards electric vehicles, cities can use our model to evaluate how much parking supply (with battery charging opportunities) they would like to dedicate to electric vehicles in order to achieve optimal traffic and parking results, and whether a differentiated or semi-differentiated parking policy is desirable. We illustrate our framework in a case study of a central area within the city of Zurich, Switzerland, showing the traffic and parking impacts (e.g., average searching time for parking, total revenue created by parking fees, optimal parking occupancy rate) for different proportions of fuel and electric vehicles in the parking demand and/or supply. Our results confirm that optimal occupancy rates are between and for most realistic scenarios. We then discuss how these rates might change depending on various demand and supply relationships, and according to different parking policies. We show that equal proportions between electric vehicles in the demand and their parking spaces in the supply lead to the best traffic performance in the area. We also provide the tools for cities to analyze their loss in performance if they do not react, e.g., to an increasing demand for electric vehicles over time. Moreover, we illustrate how some of these risks can be mitigated by having more flexible parking policies, e.g., allowing electric vehicles to use parking spaces for fuel vehicles.

Sudden variation of aerodynamic loads is the potential source of safety accidents of high-speed train (HST). As a follow-up investigation on the aerodynamic response of a HST that enters a tunnel under crosswind environment, this paper focuses on the transient response of a HST’s safety indices based on the train–track coupling interaction model. Firstly, a wind–train–track coupling dynamic model is proposed by introducing transient aerodynamic loads into the vehicle–track system. Secondly, the temporal evolution of safety coefficients indicates that the train’s safety risk increases during tunnel entry with crosswind. Results show that the derailment coefficients and wheel load reduction rate during tunnel entry are not only larger than those in open air but also those inside the tunnel due to the sudden disappearance of wind excitation at the tunnel entrance. In addition, the characteristic wind curve, which is the wind velocity against the train speed, is presented for application based on the current specification of the safety criteria threshold. The investigation will be useful in assessing the safety risk of a running train subjected to other aerodynamic attacks, such as the coupling effect of infrastructure scenario and crosswind in windy area.

This paper presents a new methodology to derive and analyze strategies for a fully decarbonized urban transport system which combines conceptual vehicle design, a large-scale agent-based transport simulation, operational cost analysis, and life cycle assessment for a complete urban region. The holistic approach evaluates technical feasibility, system cost, energy demand, transportation time and sustainability-related impacts of various decarbonization strategies. In contrast to previous work, the consequences of a transformation to fully decarbonized transport system scenarios are quantified across all traffic segments, considering procurement, operation and disposal. The methodology can be applied to arbitrary regions and transport systems. Here, the metropolitan region of Berlin is chosen as a demonstration case. First results are shown for a complete conversion of all traffic segments from conventional propulsion technology to battery electric vehicles. The transition of private individual traffic is analyzed regarding technical feasibility, energy demand and environmental impact. Commercial goods, municipal traffic and public transport are analyzed with respect to system cost and environmental impacts. We can show a feasible transition path for all cases with substantially lower greenhouse gas emissions. Based on current technologies and today’s cost structures our simulation shows a moderate increase in total systems cost of 13-18%.