Solar flares are broadly classified as impulsive or gradual. Ions accelerated in a gradual flare are thought to be accelerated through a shock acceleration mechanism, but the particle acceleration process in an impulsive flare is still largely unexplored. To understand the acceleration process, it is necessary to measure the high-energy gamma-rays and neutrons produced by the impulsive flare. Under such circumstances, on November 7, 2004, a huge X2.0 flare occurred on the solar surface, where ions were accelerated to energies greater than 10 GeV. The accelerated primary protons collided with the solar atmosphere and produced line gamma-rays and neutrons. These particles were received as neutrons and line gamma-rays, respectively. Neutrons of a few GeV, on the other hand, decay to produce secondary protons while traveling 0.06 au in the solar-terrestrial space. These secondary protons arrived at the magnetopause. Although the flux of secondary protons is very low, the effect of collecting secondary protons arriving in a wide region of the magnetosphere (the Funnel or Horn effect) has resulted in significant signals being received by the solar neutron telescope at Mt. Sierra Negra (4,600 m). This information suggests that ions on the solar surface are accelerated to over 10 GeV with an impulsive flare.

Respiratory viral infections, including influenza, respiratory syncytial virus (RSV), and, more recently, the coronavirus disease 2019 (COVID-19) pandemic, continue to pose significant global health threats. Conventional treatments for these infections often face challenges such as limited efficacy, the emergence of drug-resistant strains, and the requirement for frequent administration. In recent years, nanobodies have emerged as a promising class of therapeutic agents due to their unique properties, including small size, high stability, and specific binding capabilities. This mini-review article focuses on the application of nanobodies as spray and aerosol particles for the treatment of respiratory viral infections. Furthermore, we highlight the remarkable efficacy of nanobodies in preclinical and clinical studies against respiratory viruses, including their ability to neutralize viral particles, inhibit viral replication, and modulate the host immune response. We discuss the potential advantages of using nanobodies as inhalable formulations, including their improved delivery to the respiratory tract, enhanced stability in aerosol form, and reduced systemic side effects. Additionally, we explore the various strategies employed to engineer nanobodies for optimal aerosol delivery, such as conjugation to carrier particles or formulation as dry powders. We also examine the potential challenges and limitations associated with the development of nanobody-based aerosol therapies, including production scalability, cost-effectiveness, and regulatory considerations.

The research is focusing on analyzing the concentrations of particulate matter (PM) next to a highly congested road section, with 39,900 as a maximum number of vehicles per 24 h, in the vicinity of Timisoara, Romania. Concentrations have been measured in multiple episodes using two different measurement methods, gravimetric and dynamic light scattering, showing a disperse range of PM concentrations. Presence of metal particles in the samples have been analyzed using an electron microscope. Additionally, impact on human health is described by evaluating results for inhalable, thoracic, and alveolar sized particles.

Accumulation of proteins in filter membranes limits the efficiently of filtering technologies for cleaning wastewater. Efforts are ongoing to coat commercial filters with different materials (such as titanium-dioxide, TiO2) in order to reduce the fouling of the membrane. Beyond monitoring the desired effect of retention of biomolecules, it is demanding to understand what are the biophysical changes in water-soluble proteins caused by interacting with the new coated filter membranes, an aspect that has received little attention so far. Using spin label electron paramagnetic resonance (EPR), aided with native fluorescent spectroscopy and dynamic light scattering (DLS), here we report the changes in the structure and dynamics of bovine serum albumin (BSA) exposed to TiO2 (P25) nanoparticles or passing through commercial polyvinylidene fluoride (PVDF) membranes coated with the same nanoparticles. We have found that the filtering process and prolongued exposure to TiO2 nanoparticles had significant effects on different regions of BSA, and denaturation of the protein was not observed, neither with TiO2 nanoparticles nor by pressing through TiO2-coated filter membranes.

Previous research via cell experiments has shown that ultrafine particles (UFPs, particles less than 100 nm) emitted from Three-Dimensional desktop printers (3D printers) had cytotoxicity. However, a few particles from different filaments and their cytotoxicity combinations have been tested. Here we quantify emissions of UFPs and use Air-Liquid Interface (ALI) from one commercially available filament extrusion desktop 3D printer utilizing three different filaments by controlled experiments. A549 cells were exposed at the ALI to UFPs generated by a working 3D printer for an average of 45 minutes and 90 minutes. Twenty-four hours after exposure, cells were analyzed for percent cytotoxicity grown on the 24-well ALI insert (LDH assay). UFP exposure resulted in decreased cell viability (significantly increased LDH levels). The result shows that Acrylonitrile butadiene styrene (ABS) has the most significant particle emission. ALI exposures enable in vitro testing of mixtures of particles such as UFP from a 3D printer. ABS is the only filament with a significant difference compared with the HEPA control in 90 minutes of exposure (p-value <0.05). ABS and PETG we used during the experiment presented a significant difference compared with the HEPA control in 45 minutes of exposure.A screening analysis of potential exposure to these products in a typical environment suggests caution should be used when operating many printer and filament combinations in poorly ventilated spaces or without the aid of combined gas and particle filtration systems.

In this study, we reported that novel single-chain fusion-proteins linked thromboxane A2 (TXA2) receptor (TP) to a selected G-protein α-subunit q (SC-TP-Gαq), or s (SC-TP-Gαs) could be stably expressed in megakaryocytes (MK). We tested the MK-released platelet-linked particles (PLPs) to be used as a vehicle to deliver the over-expressed SC-TP-Gαq), or s (SC-TP-Gαs) to regulate human platelet function. To understand how the single-chain TP-Gα fusion proteins could regulate opposite platelet activities by an identical ligand TXA2, we used dual-binding domains linked to different signaling pathways within a single polypeptide chain using a 3D structural model. The immature MKs were cultured and transfected with cDNAs constructed from structural models of the individual SC-TP-Gαq and SC-TP-Gαs, respectively. After transient expression was identified, the immature MKs stably expressing SC-TP-Gαq or SC-TP-Gαs (stable cell lines) were selected. The stable cell lines were induced into mature MKs which released PLPs. Western blot analysis confirmed that the released PLPs were carrying the recombinant SC-TP-Gαq or SC-TP-Gαs. Flow cytometry analysis showed the PLPs carrying SC-TP-Gαq were able to perform the activity by promoting platelet aggregation. In contrast, PLPs carrying SC-TP-Gαs reversed Gq to Gs signaling to inhibit platelet aggregation. This is the first time demonstrating that SC-TP-Gαq and SC-TP-Gαs were successfully overexpressed in MK cells and released as PLPs with proper folding. This bio-engineering led to the formation of two sets of biologically active PLP forms, which mediate calcium and cAMP signaling, respectively. As a result, these PLPs are able to bind to identical endogenous TXA2 with opposite activities, inhibiting and promoting platelet aggregation as required for therapeutic process.The results also demonstrated the nucleus-free PLPs could be used to deliver recombinant membrane-bound GPCRs to regulate cellular activity in general.

The rapid increasing rate of soil and water bodies pollution is the main anthropogenic effect caused by the mismanagement of post-consumer plastics. This research evaluated the effectiveness of cattail (Typha Latifolia) fibers (CFs) as bio-adsorbents of microplastic particles (MPPs) from wastewater. The effect of the adsorption environment composition on the adsorption rate was investigated. Batch tests were conducted to evaluate the “spontaneous” adsorption of MPs onto CFs. Five MPPs materials (PVC, PP, LDPE, HDPE, and Nylon 6) were evaluated. An industrial wastewater (PW) and Type II Distilled Water (DW) were employed as adsorption environments. The batch tests results show that CFs are effective in removing MPPs from DW and PW. However, higher removal percentage of MPPs were obtained in PW, ranging from 89% to 100% for PVC, PP, LDPE, and HDPE; while the adsorption of Nylon 6 increased to 29.9%, a removal increased of 50%. These observations indicate that hydrophobic interactions drive the “spontaneous and instantaneous” adsorption process and that adjusting the adsorption environment effectively enhances the MPPs removal rate. This research demonstrates the important role that bio-substrates can play in reducing the environmental pollution as efficient, sustainable, low cost, and reliable adsorbents for the removal of MPPs from wastewaters.

Features of nanosecond discharge development in a non-uniform electric field are studied experimentally. High spatial resolution imaging showed that thin luminous tracks of great length with a cross-section of a few microns are observed against the background of discharge glow in air and argon. It has been established that the detected tracks are adjacent to brightly luminous white spots on the electrodes or to the vicinity of these spots, and are associated with the flight of small particles. It is shown that the traces have various shapes and change from pulse to pulse. The particle tracks may look like curvy or straight lines. In some photos, they can change the direction of movement to the opposite. The particle trace was found to abruptly cut off and a bright flash is visible at the trail break point. The color of the tracks differs from that of the spark leaders, while the bands of the second positive nitrogen system dominate in the gap spectra during the existence of a diffuse discharge. Areas of blue light are evident near the electrodes, as well. Development of glow in the gap during its breakdown is revealed using an ICCD camera. Physical reasons for the observed phenomena are discussed.

With the increase of global human activities, a large number of technogenic magnetic particles (TMPs) generated by industrial activities such as coal combustion, traffic and so on enter sediments on continental shelves. However, there is currently a lack of understanding of the spatiotemporal distribution of TMPs on continental shelves, as well as the sedimentary effects they cause. This review work comprehensively analyzes the source, morphology, composition, and spatiotemporal distribution characteristics of TMPs. Then it elucidates their magnetic contribution to sedimentary environments in continental shelf seas, as well as the influence of heavy metals and active iron. At the same time, the existing problems and future development directions of TMPs on continental shelves are summarized.

Human exposure to foodborne inorganic nanoparticles (NPs) is a growing concern. However, identifying potential hazards linked to NP ingestion often requires long-term exposure in animals. Owing these constraints, intestinal organoids are a promising alternative to in vivo experiments, as such an in vitro approach should enable rapid and reliable assessment of the effects on the gut of ingested chemicals. However, this remains to be validated for inorganic substances. In our study, a transcriptomic analysis and immunofluorescence staining were performed to compare the effects of food-grade TiO2 (fg-TiO2) on enteroid-derived monolayers (EDMs) from murine intestinal organoids to known impacts of TiO2 on intestinal epithelium. After validating their ability to dose-dependently respond to a pro-inflammatory cytokine cocktail, EDMs were exposed to 0.1, 1 or 10 µg fg-TiO2/mL for 24h. In line with known data, a dose-related increase of muc2, vilin 1 and chromogranin A gene markers of cell differentiation was observed. In addition, fg-TiO2 induced apoptosis and dose-dependent genotoxicity, while a decreased expression of genes encoding for antimicrobial peptides, and of genes related to tight junction function was observed. These results validated the use of EDMs as a reliable model for toxicity testing of foodborne NPs likely to affect the intestinal barrier.

Drought is one of the leading abiotic factors limiting morphological and physiological activities in blackberry cultivation. We investigated the effect of silver nanoparticles (AgNPs) on morphological and physiological processes in the boysenberry crop (Rubus ursinus Chamisso & Schlenhtendal) under drought stress. The experiment was performed with three drought stress levels (0% PEG, 4% PEG and 8% PEG) and three AgNPs treatments (0, 0.1, 0.2 mg L−1) invitro conditions. The results showed that drought stress induced by PEG, reduced root and shoot development of boysenberry plants grown invitro. The addition of AgNPs is significantly alleviated the adverse effect of drought stress and increased the plant growth parameters. Antioxidant activity of SOD and CAT enzymes increased in boysenberry leaves when treated with AgNPs under drought conditions, while the amount of MDA decreased. Therefore, the results obtained in this study suggest that 0.1 mg L-1 AgNPs added to the medium improve the growth and development of invitro boysenberry plants under drought stress.

For this research, a comparative evaluation was performed in which the addition of 3D-printed biocarriers fabricated with 13X and Halloysite (13Χ-Η) and commercial Kaldnes K1 biocarriers were evaluated as opposed to the non addition of biocarriers in a semi-pilot scale MBBR-MBR unit. For the evaluation of the MBBR-MBR efficiency, various physicochemical parameters were measured while static light scattering and optical microscopy observations were additionally used. Biofilm extracted from the biocarriers was also evaluated. It was observed that in the MBBR-MBR K1 unit, the membrane filtration improved while in the MBBR-MBR 13X-H unit the membrane fouling rate was the same as in the control MBBR-MBR unit. This is due to the production of large amount of SMP which resulted from the large amount of biofilm created in the 13X-H biocarriers. An optimal biodegradation of the organic load was concluded for all three MBBR-MBR units. The nitrification and denitrification processes were improved at the MBBR-MBR units using 13X-H and K1. The dry mass produced on the 13X-H biocarriers was three orders of magnitude larger than that produced on the K1. Finally, it was observed that mostly EPS was produced in the biofilm of K1 biocarriers while in the biofilm of 13X-H mostly SMP.

Filamentous manganese (Mn) oxide particles, which occur in the suboxic zone of stratified waterbodies, are important drivers of diverse elemental cycles. Although these particles are considered to be bacteriogenic, the environmental factor responsible for their formation has not been identified. Based on this study of laboratory cultures of a model Mn(II)-oxidizing bacterium, the supply of algal extracellular polymeric substances (EPS) was shown to stimulate Mn(II) oxidation and thus the production of filamentous Mn oxide particles. This observation was consistent with results obtained for naturally occurring particles collected from a near-bottom layer (depth of ~90 m) in the northern basin of Lake Biwa, Japan, that is, most Mn particles resembling delta-MnO2 were associated with an EPS-like gelatinous matrix, which contained dead algal cells and was lectin-stainable. In the lake water column, EPS produced by photosynthesis sank to the bottom layer. The analysis of the quality of water samples, which have been collected from the study site for 18 years, reveals that the annual average total phytoplankton biovolume in the surface layer correlates with the density of filamentous Mn particles in the near-bottom layer. Among different phytoplankton species, green algae appeared to be the key species. The results of this study suggest that algal EPS production induces the formation of filamentous Mn oxide particles in the near-bottom layer of the northern basin of Lake Biwa.

Exposure to particulate matter (PM) causes considerable breathing-related health risks. We assessed the inhibitory effect of Siraitia grosvenorii extract (SGE) on airway inflammation in mice exposed to a fine dust mixture of PM10 (PM diameter < 10 mm) and diesel exhaust particles (DEPs) known as PM10D. SGE attenuated neutrophil infiltration and the number of immune B and T cells in lung tissue and bronchoalveolar lavage fluid (BALF) of PM10D-exposed mice. SGE reduced the secretion of cytokines and chemokines, including interleukin (IL)-1a, tumor necrosis factor (TNF)- a, IL-17, chemokine (C-X-C motif) ligand (CXCL)-1, and macrophage inflammatory protein (MIP)-2 in BALF. Airway inflammation, accumulation of inflammatory cells, and collagen fibrosis in the lung after PM10D exposure were investigated by histopathological analysis, and SGE treatment ameliorated these symptoms. SGE decreased the mRNA expression of mucin 5AC (MUC5AC), CXCL-1, TNF-a, MIP-2, and transient receptor potential vanilloid and ankyrin 1 ion channels in the lung tissues of mice. Furthermore, SGE ameliorated mitogen-activated protein kinase (MAPK)/nuclear factor-kappa B (NF-κB) signaling activated by PM10D in mice. We conclude that SGE attenuated PM10D-induced neutrophilic airway inflammation via inhibiting MAPK/NF-κB activation. These results show that SGE may be a candidate for the treatment of inflammatory respiratory diseases.

Low-cost monitors have made possible for the first time measurements of long-term (months to years) potential indoor exposures to fine particles. Indoor and outdoor measurements made over nearly 5 years (2017-2021) by the largest network of low-cost monitors in the United States (PurpleAir) are compared to the prevalence of adult smokers in 1650 Zip codes within the three West Coast states of California, Oregon, and Washington. The results show that mean indoor exposures above the 75th percentile of adult smoking prevalence are more than 50% higher than those below the 25th percentile. Mean outdoor concentrations are also elevated, but by a smaller amount (20%). Both comparisons are significant at the p<0.001 level. The elevation of the PM2.5 concentrations with increasing smoking prevalence is evidence of environmental disparities in income, education, and other socioeconomic indices..

Respiratory syncytial virus (RSV) infection is a major cause of severe respiratory disease in infants and young children worldwide. Two vaccines targeting the elderly and pregnant women have been recently approved employing the prefusion form of the RSV-fusion protein (F). However, there are currently no vaccines for infants. Studies have shown a fusion-inactive prefusogenic F form is significantly more immunogenic and produces higher antibody titers to both the prefusion and postfusion structures of the F protein. Here we have developed RSV virus-like particles (RSV-VLPs) consisting of prefusogenic F, RSV glycoprotein and matrix proteins, produced them using the baculovirus expression system, and studied their protective efficacy in Balb/c mice. Morphology and successful assembly of VLPs were confirmed by transmission electron microscopy and western blot. Mice immunized with VLPs developed high levels of serum IgG and neutralizing antibodies as compared with mice immunized with inactivated virus. The VLP vaccine also induced higher levels of IFNγ and IL4, elicited limited proliferation of CD4+ and CD8+ T cells but higher cytotoxic-T-lymphocyte responses. VLP immunization abolished lung pathology in the mice after RSV challenge. Overall, our results indicate that RSV-VLPs consisting of prefusogenic F, glycoprotein and matrix proteins are a potential vaccine candidate against RSV.

The objective of this research is to analyze metal elements like Na (sodium), Mg (magnesium), Al (aluminum), Si (silicon), Pb (lead), K (potassium), Ca (calcium), and Fe (iron) found in dust particles within two distinct areas from which the sampling has been done. First sampling was taken from the road verge of a highly trafficked road section, while the second sampling was done in a residential garden area 90 m away from the road. Several metal elements have been detected, with a high difference for Silicon Si, which present higher concentrations in the dust sampled from the road verge area. Pb has only been detected in the samples taken from the road verge, which could be explained by residual remnants from old lead gasoline, and wheel weights. Additionally, airborne particulate matter (PM) concentrations have been measured, during the same episode, in comparison between the road verge and the garden area, presenting a substantial difference in the concentration levels, deducing that dense vegetation is protecting and blocking a majority of airborne PM. A literature highlight of health effects of different metal elements and PM concentrations is presented.

TiC particles were prepared from Ti and C powders, and TiC-reinforced Cu-based composites were prepared by powder metallurgy with SPS sintering. The effects of SPS sintering temperature and TiC particle reinforcement phase content on the electrical and mechanical properties of Cu-based composites were investigated. The reinforcement of TiC particles by thermal mismatching at increasing sintering temperature has a significant strengthening effect on the composites, but the high temperature causes softening of the Cu matrix and the growth of grains reduces the properties of the composites. In this study, the effects of porosity and density on the composite properties were not significant.

This paper presents the light scattering matrices of atmospheric aggregated hexagonal ice particles appearing in cirrus clouds. In this work aggregates consist of the same particles with different spatial orientation and number of these particles. Two types of particle shape were studied: (1) hexagonal column; (2) hexagonal plate. For both shapes we study compact and non-compact cases of arrangement of particles in aggregates. As a result, four sets of aggregates were made: (1) compact columns; (2) non-compact columns; (3) compact plates; (4) non-compact plates. Each set consists of eight aggregates with different number of particles from 2 to 9. For practical reason the bullet-rosette and the aggregate of hexagonal columns with different sizes was also calculated. The light scattering matrices were calculated for the case of arbitrary spatial orientation within the geometrical optics approximation for sets of compact and non-compact aggregates and within the physical optics approximation for two additional aggregates. It was found that light scattering matrix elements for aggregates are depend on arrangement of particles they are consisted.

The Standard Model is not a complete description of reality; it omits the existence of dark matter, dark energy, and an explanation as to why no CP violation has been observed. However, some of these phenomena could be explained through a new force mediated by a new boson. If such a boson were massless it would result in a power law potential and if massive the interaction would be Yukawa-like. A previous experiment employing a micro-mechanical oscillator and a spherical test mass interactions was successful in placing the best limits on a mass-mass Yukawa-like interaction, but the data was never analyzed in the context of a power law. Here that data is analyzed considering a power law for powers n = 1-5 where n is the number of boson exchanges. The results show that the limits obtained through power law analysis of this data are not better than the currently accepted limits. A discussion of an experiment design capable of producing better limits on power law extensions to the Standard Model is presented, and suggests micro mechanical oscillators based experiment remains capable of improving the limits by at least one order of magnitude.

An accurate flux measurement of low-energy charged particles trapped in the magnetosphere is necessary for space weather characterization and to study the coupling between the lithosphere and magnetosphere, which allows for the investigation of the correlations between seismic events and particle precipitation from Van Allen belts. In this work, the project of a CubeSat space spectrometer, the Low-Energy Module (LEM), is shown. The detector will be able to perform an event-based measurement of the energy, arrival direction, and composition of low-energy charged particles down to 0.1 MeV. Moreover, thanks to a CdZnTe mini-calorimeter, the LEM spectrometer also allows for photon detection in the sub-MeV range, joining the quest for the investigation of the nature of Gamma-ray bursts. The particle identification of the LEM relies on the ΔE−E technique performed by thin silicon detectors. This multipurpose spectrometer will fit within a 10 × 10 × 10 cm3 CubeSat frame, and it will be constructed as a joint project between the University of Trento, FBK, and INFN-TIFPA. To fulfil the size and mass requirements, an innovative approach, based on active particle collimation, was designed for the LEM; this avoids the heavy/bulky passive collimators of previous space detectors. In this paper, we will present the LEM geometry, its detection concept, the results from the developed GEANT4 simulation, and some characterisations of a candidate silicon detector for the instrument payload.

Flotation of small particles is one of the global challenges facing the mineral raw materials processing industry. Large amounts of non-ferrous and rare metals are lost in the flotation tailings in the form of mineral particles below 15 µm in size as a result of the low effectiveness of their capture by coarse bubbles generated in conventional flotation machines. The method of combined microflotation, which is being developed in recent years, uses not only coarse but also microbubbles (MB) produced in the stand-alone generator of air-in-water microdispersion, which serves as the flotation carriers. Depending on the dose of MB, the effect of their application may be both positive, but also negative. The theoretical analysis of various mechanisms of particle transfer onto the surface of coarse bubbles and further into the froth layer allowed to obtain the formula for the optimal MB dose f=2dddpρp, where dd is MB size; dp and ρp respectively are the size and the density of particles. Experiments performed on the copper ore flotation tailings at the Atalaya Mining (Spain) and Chaarat Kapan (Armenia) concentrators showed that, besides the optimal MB dose in the range of 1-3 ml/g, there is another optimal MB dose in the range of 10-20 ml/g, where the copper recovery increases by several percent compared to the reference test (f= 0). In the area between the optimal MB doses, the deep minimum in copper recovery is observed, which value is by several percent lower compared to the value in the reference test.

In order to study the effect of TiB2 particles on the mechanical properties of TiB2/6061Al composites, a series of TiB2/6061Al 3D representative volume element (RVE) were established based on SEM photos. This model took into account the ductile damage of the matrix and the traction separation behavior of the interface, and the linear damage evolution law was introduced to characterize the stiffness degradation behavior of the matrix elements. The mixed boundary conditions were used for RVE tensile experiments, and the accuracy of the predicted result was verified by the agreement of the experimental stress-strain curve. Results show that the addition of TiB2 particles can effectively promote the load-bearing capacity of the composite, but elongation is reduced. With the weight fraction of TiB2 increasing from 2.5% to 12.5%, the elastic modulus, yield strength, and tensile strength are increased by 8%, 10.37%, and 11.55% respectively, while the elongation decreased by 10%. The clustering rate of the TiB2 particles is also an important factor affecting the toughness of the composites. With the increase in the clustering rate of TiB2 particles from 20% to 80%, the load-bearing capacity of the composites is not improved, and the elongation of the composites is reduced by 8%. Moreover, the high strain region provides a fast expansion path for crack propagation and the particle spacing is a crucial factor that affects the stress field.

The determination of the specific surface free energy, specific properties and Lewis’s acid base of solid materials is of capital importance in many industrial processes such as adhesion, coatings, two dimensional films and adsorption phenomena. (1) Background: The physicochemical properties of many solid particles were characterized during the last forty years by using the retention time of injected well-known molecules into chromatographic column containing the solid substrates to be characterized. The obtained net retention time of the solvents adsorbed on the solid allowing the determination of the net retention volume directly correlated to the specific surface variables, dispersive, polar and acid-base properties. (2) Methods: Many chromatographic methods were used to quantify the values of the different specific surface variables of the solids. However, one found a large deviation between the different results. In this paper, one proposed a new method that quantify the specific free energy of adsorption as well as the Lewis’s acid-base constants of many solid surfaces. (3) Results: The new applied method allowed us to obtain the specific enthalpy and entropy of adsorption of polar model organic molecules on several solid substrates such as silica, alumina, MgO, ZnO, Zn, TiO2 and carbon fibers. (4) Conclusions: our new method based on the separation between the dispersive and polar free surface energy allowed to better characterize the solid materials.

Iron (Fe), the main component of non-exhaust particulates, is known to have variable health effects that depend on the chemical species of iron. This study characterized the possible contribution of iron oxides and hydroxides to airborne brake-wear particles under realistic vehicle driving and braking conditions with different brake-pad friction materials. We found significant differences in wear coefficients and PM₁₀ emissions between non-asbestos organics (NAO) and European performance (ECE) brake pads. Iron was the dominant contributor to PM₁₀ and PM_2.5 brake-wear particles for both NAO and ECE. The iron concentration ratio in the particle mass were comparable to the disc to pads ratio measured by wear mass. The fact that magnetite, which is of interest with respect to health effects, was less abundant in NAO than in ECE suggested that tribo-oxidations occurred in NAO. Metallic iron is generated not only from abrasive wear but also from tribo-chemical reduction with magnetite as the starting material. We found differences not only in PM emissions between brake friction materials but also that the phase transformations of iron differed between friction materials. These differences were apparent in the distribution of iron oxides and hydroxides. Heat, tribo-oxidation, and tribo-reduction are intricately involved in these reactions.

Despite the recognized potential of nanoparticles, only a few formulations have progressed to clinical trials, and an even smaller number have been approved by the regulatory authorities and marketed. Virus-like particles (VLPs) have emerged as promising alternatives to most explored nanoparticles because of the absence of viral genetic material, their incapacity to replicate, mimicry of viral structure, and tropism conservation. Furthermore, VLPs can be surface functionalized with small molecules to improve circulation half-life and target specificity. Through the functionalization and coating of VLPs, it is possible to optimize the response properties to a given stimulus, such as heat, pH, an alternating magnetic field, or even enzymes. Surface functionalization can also modulate other properties, such as biocompatibility, stability, and specificity, deeming VLPs as potential vaccine candidates or delivery systems. In this review, we address the different types of functionalization of VLPs, their importance, and their consequent biomedical applications.

This study introduces a neural network-based approach to predict dust emission, specifically PM2.5 particles, during almond harvesting in California. Using a feedforward neural network (FNN), the research predicts PM2.5 emissions by analyzing key operational parameters of an advanced almond harvester. The model is trained on extensive field data from the almond pickup system, including variables like brush speed, angular velocity, and harvester forward speed. The results demonstrate a notable predictive accuracy of the FNN model, with a Mean Squared Error (MSE) of 0.02 and a Mean Absolute Error (MAE) of 0.01, indicating a high degree of precision in forecasting PM2.5 levels. The study also finds a strong correlation between certain operational parameters and PM2.5 emissions, highlighting specific areas for optimization in harvesting techniques. By integrating machine learning with agricultural practices, this research provides a significant tool for environmental management in almond production, offering a method to reduce harmful emissions while maintaining operational efficiency. This model presents a solution for the almond industry and sets a precedent for applying predictive analytics in sustainable agriculture.

Two pilot scale desalination system employing carbon modified nano-sized, zero valent metals (n-ZVM) were maufactured and tested to determine (1) the degree to which high salt water (20 to 130 mS) could be desalinated and (2) if this degree of desalination could be maintained throughout an extended treatment period. Two pilot systems were tested (referred to as Generation 1 and Generation 2) consisting of parallel lines of 4 individual reactors in series, a settling tank and an activated carbon cell at the end of each reactor line. The system capacity was 300 gal in Generation 1 and 600 gal in Generation 2 total with a total hydraulic residence time of 6 hours per reactor line (one hour per cell/tank). A slurry of n-ZVM was introduced in the first reactor on each line to yield approximately 5 to 45 grams of nano-metal per 100 L of influent salt water. The n-ZVM slurry was made from mixing tea extract with metal salts (eg ferrous sulfate, ferric chloride) to produce the carbon modified metal slurry. Initial runs focused on dosing required to achieve maximum salt removal at each of three influent salt contents, 28 mS, 44 mS and 123 mS. Once dosing was set, continuous runs (14 days, 23 days and 9 days) were carried out to (1) examine the ability of the pilot to maintain the removal efficiency over an extended period, (2) to determine the weaknesses inherent in the pilot systems, and (3) to begin to develop CAPEX and OPEX estimates for the pilot and pre-design full scale mobile desalination unit (MDU) system. Results demonstrated that maximum removal occurred with 10 g/100L of salt for the 30 mS salt solution,16 g/100 L of salt for the 40 mS influent water and 40 g/100 L for the 130 mS influent. Salt removal (expressed as Na and Cl removed) approached 78% for the 30 mS influent and 41 mS influent respectively while removal for the highest salt influent (130 mS) approached 81 %. Addition of greater amounts of carbon modified slurry than those described resulted in a pH less than 6 which inhibits continued salt removal and would require addition of calcium or magnesium oxides/hydroxides or bicarbonate solutions at the influent side to achieve greater salt removal and of course greater cost per gallon. Continuous operation over the extended time-period showed no significant decrease in salt removal with typical day to day variation of no more than 10% suggesting that this approach to desalination could rapidly provide usable water from saline aquifers, seawater or even produced water. Treatment of saline waters at 30 mS or less yields effluent water in the range necessary for irrigation use of many crops while treatment of seawater or produced water levels of salt (40 mS or higher) yields effluent in the range of 8 to 10 mS a range ideal for RO influent that would prevent the production of large volumes of brine. Pilot testing continues with seawater extracted from Puget Sound, Seattle WA and higher levels of salt to better represent produced water.

Keywords: liquid alloys, microstratification, dispersed particles, spontaneous dispersion, criteria for true (entropic) spontaneous dispersion, mechanisms of quasi-spontaneous dispersion, methods and results for assessing size of dispersed particles.

A homogenization of billets from Al-Cu-Li-Mg-Sc-Zr alloys should be accomplished at high annealing temperatures exceeding 500 °C. This type of aluminum alloy is susceptible to the depletion of surface layers from Li. Therefore, choosing a suitable homogenization temperature and duration is a crucial step in assuring a homogeneous distribution of alloying elements and optimal exploitation of the potential of the alloy. In-situ heating in an electron microscope was performed on a twin-roll cast Al-Cu-Li-Mg-Sc-Zr alloy to understand the peculiarities of the homogenization process. Four types of primary phase particles rich in Cu, Li, Mg, and Fe were identified in the as-cast material. They appear as coarse particles at the boundaries of eutectic cells. Their partial dissolution occurs at temperatures above 450 °C. They are almost fully dissolved at 550 °C, except for complex phases containing Fe and Cu. Small dimensions of eutectic cells in the range of 10 µm assure a homogeneous distribution of main alloying elements within the matrix after 20 min of annealing. Direct comparison with the same material prepared by mold-casting indicates that such short annealing times result in the dissolution of main primary phase particles but do not assure a homogeneous distribution of alloying elements in the whole volume of the specimen.

The flow field around a straight chain of multiple slip spherical particles rotating steadily in an incompressible Newtonian fluid about their line of centers is analyzed at low Reynolds numbers. The particles may vary in radius, slip coefficient, and angular velocity, and they are permitted to be unevenly spaced. Through the use of a boundary collocation method, the Stokes equation governing the fluid flow is solved semi-analytically. The interaction effects among the particles are found to be noteworthy under appropriate conditions. For the rotation of two spheres, our collocation results for their hydrodynamic torques are in good agreement with the analytical asymptotic solution in the literature obtained by using a method of twin multipole expansions. For the rotation of three spheres, the particle interaction effect indicates that the existence of the third particle can influence the torques exerted on the other two particles noticeably. The interaction effect is stronger on the smaller or less slippery particles than on the larger or more slippery ones. Torque results for the rotation of chains of many particles visibly show the shielding effect among the particles.

Radio bursts provide important diagnostics of energetic phenomena of the Sun. In particular, bursts in decimetric and metric wavelengths probe the physical conditions and the energy release processes in the low corona as well as their association with heliospheric phenomena. The advent of spectral radio data with high time and high frequency resolution has provided a wealth of information on phenomena of short duration and narrow bandwidth. Of particular value are spectral data combined with imaging observations at specific frequencies. In this work we briefly review the results of a series of observations comprised from high-sensitivity, low-noise dynamic spectra obtained with the acousto-optic analyzer (SAO) of the ARTEMIS-IV/JLS solar radiospectrograph, in conjunction with high time-resolution images from the Nançay Radioheliograph (NRH). Our studies include fine structures embedded in type IV burst continua (mostly narrow-band "spikes" and intermediate drift "fiber" bursts) and spike-like structures detected near the front of type-II bursts. The implications of the observational results to theoretical models are discussed.

This article begins with exploring fundamental limits in the universe. It examines key principles, such as the uniformity of physical laws and Energy conservation, that lead to maximum speed, locality, and maximum density. These universal limits govern physical phenomena, leading to very interesting results.I demonstrate that quarks and leptons comprise smaller entities named "Quantum Black Holes." These Quantum black holes are relativistically rotating miniature charged black holes consisting of a single core at the highest possible density. Quantum black holes are the only structures small enough in space-time capable of keeping all charges quantized (including gravitational charges.)By the end of the article, I prove that Quantum black holes explain the deficiencies of SM. They facilitate explanations of quantized gravity, the nature of Luminous and dark Matter, establishing the Mass, size, and (quantized) charges quantities of elementary particles, the nature of neutrino oscillations, and more. Elementary particles release their Energy outward, altering the curvature of nearby space-time and providing new insights into the nature of space-time curvature change. With this understanding, we can characterize movements and processes in local space-time using five sets of equations simultaneously: four representing the four charge types and one representing Dark Matter.

A systematic investigation of the dynamic clustering behavior of active particles under confinement, including the effects of both particle density and active driving force is presented based on a hybrid coarse-grained molecular dynamics simulation. First, a series of scaling laws were derived with power relationships for the dynamic clustering time as a function of both particle density and active driving force. Notably, the average number of clusters N ̅ assembled from active particles in the simulation system exhibits a scaling relationship with clustering time t described by N ̅∝t^(-m). Simultaneously, the scaling behavior of the average cluster size S ̅ is characterized by S ̅∝t^m. Our findings reveals the presence of up to four distinct dynamic regions concerning clustering over time, with transitions contingent upon the particle density within the system. Furthermore, as the active driving force increases, the aggregation behavior also accelerates, while an increase in density of active particles induce alterations in the dynamic procession of the system.

If we assume that: a. The four fundamental forces of nature are independent waves without rest masses, and their speeds are constant in a vacuum, just like light. b. Light or electromagnetic waves and gravity are comparable in structures. Weak and strong interactions are similar in structures. c. Light and weak interaction have the same speed c_L with spin number +1 or –1. d. Gravity and strong interaction have the same speed c_G without spin. e. The primary particles, namely electrons, electron neutrinos, and dark neutrinos in this paper, are made by the above four waves. We can find and describe some fundamental characteristics of the primary particles (e.g., their sizes, energies, and interactions) and introduce new attractive results from them (e.g., the source of the Pauli exclusion principle, the solution to the Einstein-Podolsky-Rosen paradox, and c_G slightly faster than c_L).

Thin Pd-40%Cu films were obtained by the classical melting and rolling method, magnetron sputtering and modified with nanostructured functional coatings to intensify the process of hydrogen transport. The films were modified by electrodeposition according to the classical method of obtaining palladium black and "Pd-Au nanoflowers" with spherical and pentagonal particles, respectively. The experiment results demonstrated the highest catalytic activity (89.47 mA cm–2), good resistance to CO poisoning and long-term stability of Pd-40%Cu films with a pentagonal structured coating. The investigation of the developed membranes in the hydrogen transport processes in the temperature range of 25-300°C also demonstrated high and stable fluxes up to 475.28 mmol s–1 m–2 (deposited membranes) and 59.41 mmol s–1 m–2 (dense-metal membranes), which turned out to be up to 1.5 higher compared to membrane materials with classic niello. For all-metal modified membranes, the increase in flux was up to 7 times, compared with a smooth membrane made of pure palladium, and for deposited films, this difference was several tens of times. The membrane materials selectivity was also high up to 4419. The developed strategy for modifying membrane materials with functional coatings of a fundamentally new complex geometry can shed new light on the development and fabrication of durable and highly selective palladium-based membranes for gas steam reformers.

The pressing process and density profile of particleboards produced with addition of waste wood containing phenol-formaldehyde (PF) resin was presented. The particles were melamine-urea-phenol-formaldehyde (MUPF) resinated. Recovered particles were obtained from post-industrial waste plywood. The press closing time recorded during the pressing of mats containing only recovered particles in the core layer (100%), at a unit pressure of 3 MPa, in which the face layer rate was 50%, resin load for face and core layer was 12% and 10% was shorter by 29% than for the industrial particle mats. Regardless of the level of variability of independent factors the overheating time of mats to a temperature of 100 °C, containing recovered particles was 10% - 20% shorter than the time of overheating mats with industrial particles. The greatest impact (52%) on maximum density of the face layer of particleboards was demonstrated by the content of the recovered particles and the resin load (32%). The maximum density area of the face layer was located closer to the surface in particleboards produced with a higher (80%, 100%) content of the recovered particles, a higher (i.e. 12% and 10%, respectively, for face and core layer) resin load, a lower (35%) face layer rate and a higher (3 MPa ) unit pressure.

Recent researches indicated that metal nanoparticles which have the unique optical properties can be used to enhance the spectral response of the photovoltaic modules. Since most of the nanoparticles have enhancement effects in a specific wavelength range, improving the spectral response of the photovoltaic modules in a broadband range is crucial for their applications in imaging, energy harvesting, and optical communication. In this study, flower-like silver particles are applied to achieve the enhancement effects in a broadband range. The optical absorption of photovoltaic modules is improved in a broad wavelength range of 400~2000 nm by immobilizing flower-like silver particles onto an amorphous Si p-i-n structure, and the peak responsivity of the spectral response is enhanced by about 10 times. Theoretical investigation further elaborates that the enhancement originates from the near-field effects of silver particles due to the interaction of different parts of the flower-like silver particles. Through these studies, we demonstrate that, utilizing the subwavelength silver particles with roughness surface can achieve the spectral response of the photovoltaic modules enhanced in broadband range, which can improve the utilization efficiency of optical energy for the applications of sensing, imaging, optical communication, and energy harvesting.

Zeta potential refers to the electrokinetic potential present in colloidal systems, exerting significant influence on the diverse properties of nano-drug delivery systems. The impact of dielectric constant on the zeta potential and charge inversion of highly charged colloidal particles, immersed in a variety of solvents spanning from polar, such as water, to nonpolar solvents, and in the presence of multivalent salts, was investigated through primitive model Monte Carlo (MC) simulations. Zeta potential ξ is decreased as decreasing the dielectric constant of the solvent, and upon further increase in the salinity and the valency of the salt. At elevated levels of salt, the colloidal particles become overcharged, in all solvents. As a result, their apparent charge becomes opposite in sign to the stoichiometric charge. This reversal of charge intensifies until reaching a saturation point with further increase in salinity, as a result, their apparent charge becomes opposite in sign to the stoichiometric charge. This reversal of charge intensifies until reaching a saturation point with further increase in salinity.

Solar energetic particles (SEPs) are bursts of high-energy particles that originate from the Sun and can last for hours or even days. The aim of this study is to understand how the characteristics of energetic particles was affected by the characteristic parameters of corotating interaction regions (CIRs). In particular, the particle intensity distribution with time and space in different CIRs are studied. The propagation and acceleration of particles are described by the focused transport equation (FTE). We used a three-dimensional magnetohydrodynamic (MHD) model to simulate the background field including CIRs. By changing the inner boundary conditions, we constructed CIRs with different solar wind speeds, angles between the polar axis and rotation axis, and the azimuthal widths of the fast streams. Impulsive particles are injected at the inner boundary. We then study the SEPs in different backgrounds. The results show that the CIR widths are related to the solar wind speed, tilt angles, and the azimuthal widths of the fast stream. The acceleration of particles in the reverse and forward compression regions is mainly influenced by the solar wind speed difference and the slow solar wind speed, respectively. Particles with lower energy (sub-MeV) are more sensitive to the parameters of CIRs. Different CIR parameters also greatly affect the spatio-temporal distribution of particle intensities in different ways. These results indicate that, it is crucial to consider the conditions of large-scale structure in interplanetary space when studying or predicting energetic particles. Additionally, our findings provide empirical guidance for forecasting the characteristics of SEPs.