Porous β-tricalcium phosphate (Ca3(PO4)2; β-TCP) was prepared by freeze-drying and the effects of this process on pore shapes and sizes were investigated. Various samples were prepared by freezing β-TCP slurries above a liquid nitrogen surface at −180 °C with subsequent immersion in liquid nitrogen at −196 °C. These materials were then dried under reduced pressure in a freeze-dryer after which they were sintered by heating. Compared with conventional heat-based drying, the resulting pores were more spherical, which increased both the mechanical strength and porosity of the β-TCP. These materials had a wide range of pore sizes from 50 to 200 µm, with the mean and median values both approximately 100 µm regardless of the freeze-drying conditions. Mercury porosimetry data showed that the samples contained small, interconnected pores with sizes of up to 1.24 µm and macroscopic, interconnected pores up to 25.8 µm in size. The effects of non-ionic surfactants having different hydrophilic/lipophilic balance (HLB) values on foaming and pore size were also investigated. Materials made with surfactants having lower HLB values exhibited smaller pores and lower porosity whereas higher HLB surfactants gave higher porosity and slightly larger macropores. Even so, the pore diameter could not be readily controlled solely by adjusting the HLB value. The findings of this work indicated that high porosity (75%) and good compressive strength (>2 MPa) can both be obtained in the same porous material and that foaming agents with HLB values between 12.0 and 13.5 were optimal.

Obesity is a worldwide epidemic; hence it is crucial to understand how it can be effectively prevented/treated. Thus, obesity should be tackled considering that it is a multifactorial condition. This work examines a wide range of factors and attempts to understand which contribute most to variability in overweight/obesity. Eighty-four subjects with overweight/obesity were recruited. Dietary baseline information was obtained by analyzing three 24-hour recalls. Resting metabolic rate was measured using indirect calorimetry, physical activity through accelerometry, cardiometabolic parameters were determined in blood samples and body composition by anthropometry and bioimpedance. Factor analysis of principal components (PCA) was carried out (SPSS v22.0). Large interindividual variability was observed in dietetic, biochemical, and physical activity measurements (coefficient of variation ≥30%), but body composition was homogeneous. Volunteers had an unbalanced diet and low physical activity. PCA reduced the 26 analyzed variables into 7 factors, accounting for 81,5% of total data variability. The main factor was the ‘‘caloric and lipid factor’’ related to diet, responsible for 25.9% of total variability, followed by ‘‘adiposity factor’’ (16,9%) and ‘‘cardiometabolic risk factor’’ (13,2%). Diet seems to be the factor that contributes the most to data variability in people with overweight/obesity, especially the intake of lipids, energy and proteins.

This article presents a hybrid approach to assessing students’ foreign language proficiency in a cyber-physical educational environment. It focuses on the advantages of integrated assessment of student knowledge by considering the impact of automatic assessment, learners’ independent work, and their achievements to date. An assessment approach is described using the mathematical theory of fuzzy functions, which are employed to ensure fair evaluation of students. The largest possible number of students, whose re-evaluation of test results will not affect the overall performance of the student group, is automatically determined. The study also models the assessment process in the cyber-physical educational environment through the formal semantics of calculus of context-aware ambients (CCA).

The main objective of this this cross-sectional study was to analyze the influence of lifestyle fac-tors (diet, physical activity, sleep), which can affect the concentrations of fecal short-chain fatty acids (SCFAs) and SCFAs potential role in modulating cardiometabolic disease risk by interact-ing with biochemical and body composition parameters. The study comprised 77 healthy, non-obese individuals, aged 30-45 years who were assessed in the light of SCFAs concentration in stool, diet, physical activity level and sleep duration. Moreover, body composition measurement and patients’ biochemical parameters were included in the analysis. We have indicated a signifi-cant negative correlation between several SCFAs [especially acetic acid (AA), isobutyric acid (IBA), butyric acid (BA), isovaleric acid (IVA) and valeric acid (VA)] with BMI, VAT/SAT ratio (visceral to subcutaneous fat ratio) and percentage of fat mass in a group of females enrolled in the study as well as with waist circumference (WC) in case of both sexes included in the study. Moreover, the results of our study acknowledged the importance of a diet in shaping SCFAs pro-file - we noticed the significant negative associations between energy and fat intake and some SCFAs in males [IBA, IVA, VA, isocaproic acid (ICA)]. In terms of fiber intake, we noticed elevat-ed concentrations of vast majority of SCFAs and amount of SCFAs in total in case of both sexes included in the study. These strong correlations reflect the fact that diet shapes the composition of the gut microbiota and SCFAs (main microbial metabolites) are synthesized from dietary fiber. Furthermore, we noticed that in a group of women, the concentration of AA, propionic acid (PA) and ICA as well as the total concentration of SCFAs showed a significant positive association with their sleep duration. We concluded that SCFAs can have a potential role in modulating car-diometabolic disease risk by interacting with adiposity parameters and diet. In addition, this potential direct link between diet and SCFAs may at least partly contribute to sleep improvement.

Mathematics first is a logical system. But, the Mathematics Crisis showed that we cannot have a logical self-consistent mathematics system. Physics is a kind of applied science. It first need be valid to invent new production and understand new observation. In one theory of physics, the studied object is usually defined as an abstract concept. For example, the Sun is defined as a point particle in the Newtonian theory of gravity. In different theories of physics, the abstract concept for a same object is different. It determines that logical self-consistent is not needed for different theories of physics. Physics only can be developed from observation and experiment. But, in the past a century, physicists’ main attempt is to have a standard model, such as the Grand Unification or the Theory for Everything, from mathematics derivation. Therefore, the current attempt to develop new physics is questioned. In recent, the strong gravitational field was studied. It is found that the fundamental physical constants which are measured in the weak field shall be varied in a super strong field. For the two reasons, modern physics need be advanced greatly.

As the application of cyber-physical systems (CPSs) becomes more and more widespread, its security is becoming a focus of attention. Currently, there has been much research on the security defense of the physical layer of the CPS. However, most of the research only focuses on one of the aspects, for example, attack detection, security state estimation or recovery control. Obviously, the effectiveness of security defense targeting only one aspect is limited. Therefore, in this paper, a set of security defense processes is proposed for the case that a CPS containing multiple sensors is subject to three kinds of stealthy attacks (i.e., zero-dynamics attack, covert attack, and replay attack). Firstly, the existing attack detection method based on improved residuals is used to detect stealthy attacks. Secondly, based on the detection results, an optimal state estimation method based on improved Kalman filtering is proposed to estimate the actual state of the system. Then, based on the optimal state, internal model control (IMC) is introduced to complete the recovery control of the system. Finally, the proposed methods are integrated to give a complete security defense process, and the simulation is verified for three kinds of stealthy attacks. The simulation results show that the proposed methods are effective.

The purpose of the review is to provide new insight into the potential of surface modification of carbon fibers for enhancing the application of the carbon fibers many a fold. To this end a total of 429 papers on the subject of surface modication of carbon fibers by a variety of chemical and electrochemical methods published during the period from 2010-2022 have been reviewed. Astounding results of surface funcationalization of carbon fibers by a variety of state of the art methods resulting in the unconventional applications of the resulting modified carbon fibers are summarized in a nut-shell in schemes from 1-6 towards the end of the review. Surface modifica-tion induces functionality to carbon fibers (CFs). The vitality of CF surface modification reac-tions could only be compared to the life process of respiration that sustains the multi functional-ity of living cells. Applicability of CFs can be drastically enhanced in incomprehensible ways by surface modification. Upon surface modification, inert and non-reactive CF surface becomes chemically active and functional with utility in diverse fields, namely, health, energy, environ-ment, defense, catalysis, smart materials and many others. Surface modification methods can be broadly classified into chemical, electrochemical and physical methods. By these surface modi-fication methods, the inert FC surface becomes polar. Surface properties like roughness, wetta-bility and energy are enhanced. Modification processes like sizing, oxidation, amination, si-lanization, polymerization, nanoarchitecture induces multifunctionality on CF surface. Modi-fied CFs when used as reinforcing material in carbon fiber reinforced plastics (CFRPs), im-proved bonding at the interface with resin matrices is observed with enhanced and outstanding mechanical properties (flexural strength, flexural modulus, IFSS, ILSS, hardness, elastic modulus, bending strength and compression strength).

This paper reviews the low-resilience problem in many cities, poor designs of cities to cope with disasters, and the need for tolerance of urban constructions. It explores answers concerning the question of how shall we build cities resiliently? The method of this applied research is a multiphase process that considers all physical and socioeconomic elements of a city. It introduces six indicator groups of urban management (M), economy (E), built environments (U), Infrastructures (I), natural environments (N), and health protection (H). The groups include 55 indicators as variables in the mathematical calculations in this paper. This paper builds a mathematical model to maximize the profitability of resilient buildings by optimizing investments in the required projects. The projects will upgrade the firmness and tolerance of cities against nature-based and human-made dangers and risks. There is a linear programming in 55 variables to select optimal solutions from fifty-five factorial alternatives. Then, the programming will develop into non-linear programming. The unique innovation of this paper is its linear programming interpretation by non-linear to give optimal solutions for the problem. Applying the Lagrange function in the Kuhn-Tucker conditions proves the accuracy of the hypothesis that post-COVID urbanization requires maximum resilience. Only in this way, the urban economies will be free of risks. Outcomes in this paper will assist in the pre-planning, design, and building of built environments everywhere resilient and sustainable.

The aspirated hypersonic air-breathing propulsion system requires a large amount of power generation, but its special structure makes it impossible to adopt common power generation methods. The high-temperature gaseous hydrocarbon fuel thermal power generation (TPG) system was developed to solve the power generation problem for hypersonic air-breathing propulsion system. But off-design operating conditions of the hypersonic propulsion system results in a more complex process for both propulsion system and the TPG system. To better analyzing the dynamic thermos-physical characteristics of hypersonic airbreathing propulsion system considering thermal-mechanical coupling process among cooling/TPG system, a dynamic analytical model was developed, and the dynamic thermos-physical characteristics of TPG system under different off-design working conditions were conducted. It can be concluded from the analytical results that the dynamic process of thermos-physical characteristics shows a complex trend under the flight Mach number and fuel equivalence ratio off-design working conditions. Such complexity of dynamic characteristics brings difficulties in fuel supply for the propulsion system.

In the construction business, which is known for its intricate and strategic nature, it is crucial to have efficient risk management in place. This is because various internal and external elements can cause disruptions to projects. Although the industry has had a historically negative reputation for risk analysis, the methodical process of identifying, analyzing, and managing risks has been more widely recognized and respected. This paper examines the historical progression of construction risk management, highlighting the need to identify and classify risks promptly. The study examines various risk factors related to finance, law, environment, and logistics. The study explores various risk management strategies, such as contract management, risk distribution, evaluation, mitigation, and sharing. The article discusses the significant impact of risk management software, such as Procore, PlanGrid, e-Builder, Autodesk BIM 360, and Oracle Primavera, on improving project results. The study finishes by highlighting the importance of proactive risk management in protecting against financial losses and maintaining a reputation in the construction business.

Hispanics are disproportionately affected by low rates of physical activity and high rates of chronic diseases. Hispanics generally and Mexican Americans specifically are underrepresented in research on physical activity and its impact on mental well-being. Some community-based interventions have been effective in increasing physical activity among Hispanics. This study examined data from a sample of low-income Hispanic participants in free community exercise classes to characterize the association between self-reported frequency of exercise class attendance, intensity of physical activity, and participant well-being. As part of two cross-sectional samples recruited from a stratified random sample of community exercise classes, 302 participants completed a questionnaire consisting of a modified version of the Godin-Shephard Leisure-Time Exercise Questionnaire (LTEQ) and the Mental Health Continuum Short Form (MHC-SF). Adjusted binary logistic regression analyses indicated that those who achieve moderate and strenuous self-reported physical activity have 130% higher odds (p = 0.0422) of positive mental well-being after adjustment for age, attendance, and self-reported health. This study provides evidence that physical activity intensity and time are associated with flourishing mental health among Hispanics. The study provides insight into the planning and development of community-based physical activity programming tailored to low-income populations.

Based on the engineering background of Daliuta mining area, the fracture distribution and water movement within the weakly cemented overlay strata are studied through liquid-solid coupling physical simulation and COMSOL numerical simulation test. 3D fracture network of overburden strata in mining is plotted based on the result of the physical simulation test. The results showed that the ‘fractured zone’ of the weakly cemented overburden strata in the western area develops more evidently than that in the eastern area ---- wide-opened fractures form at both ends of the working area and this leads to a wide distribution of fractures in the overlying strata.After the initial caving of the roof, height of the penetrating fractures increases rapidly and the separated strata space becomes the main channel for water flow. Under the action of water flow and rock strata movement, mining-induced fractures in overlying rock display cyclic change of expansion, penetration and closure. When the working face is fully mined, the penetrating fractures in the overlying strata and mining-induced fractures up in the working face become the main passages for water flow. The experimental result provides a reference for underground reservoirs layout and maintenance and water-conserved mining in western China.

The phenomenon of dissipative self-organization is studied on the example of time-crystal networks. Particular attention was given to transient processes, attractor topologies, phase transitions, and asymptotic stability. New concepts were introduced, including topological phases, spinorial states, and bond flavors. Concepts such as ground states, chemical potentials, elastic forces, temperature, and statistical distributions were endowed with a new meaning associated with asymptotic stability. Phenomena usually attributed exclusively to quantum physics have been shown to occur in this essentially classical environment. They coexist with, and in some cases, such as charge quantization, are related to the phenomenon of time dilation. The approach was applied to model vacuum self-organization. We have shown that under the ac-tion of competing forces, such as gravity and antigravity, a cascade of phase transitions can transform an unorganized vacuum into phases in which interactions, fields and waves resemble electromagnetic, weak, and strong, and their elements can be used as building blocks for prototype particles. In addition, some interrelation field parameters and probabilities of particle transmutations were calculated, which are not predicted by the standard model. The results are consistent with the experiment. The presented material and methodology may be of interest for studying self-organization in different environments.

Urinary incontinence (UI) is a common geriatric syndrome affecting bladder health and is especially prevalent in nursing homes (NHs). The aim of the study was to determine the prevalence of UI and its associated factors in 5 Spanish NHs. UI (measured with Minimum Data Set 3.0.), sociodemographic and health-related variables were collected. Chi- square (or Fisher’s) or Student’s t-test (or Mann Whitney U) for bivariate analysis were used, with Prevalence Ratio (PR) as an association measure. The prevalence of UI was 66.1% (CI:95%, 53.6–77.2) and was significantly associated with frailty (PR 1.84; 95%CI 0.96–3.53), faecal incontinence (FI) (PR 1.65; 95%CI 1.02–2.65), anxiety (PR 1.64; 95%CI 1.01–2.66), physical performance (PR 1.77; 95%CI 1.00–3.11) and cognitive state (PR 1.95; 95%CI 1.05–3.60). Statistically significant differences between incontinent-continent groups were found for activities of daily living (ADL) limitations, mobility, quality of life, sedentary behaviour (SB) and handgrip strength. It can be concluded that 2/3 of the residents experienced UI, and its significant associated factors were mainly physical (SB, frailty, physical performance, ADL limitations, mobility, FI and handgrip strength) followed by psycho-cognitive factors (cognition, anxiety and quality of life).

This study aimed to evaluate whether primary school classroom teachers reported changes in physical education teaching self-efficacy (SE-PE) and work engagement (WE) during the first COVID-19 wave. Six-hundred-twenty-two classroom teachers filled in an online questionnaire on SE-PE and WE, referring to before and during the lockdown, and on perceived digital competence. While controlling for perceived digital competence, a mixed between-within Repeated Measures Multivariate Analysis of Covariance (RM-MANCOVA) was performed, with a two-time (before vs. during the lockdown) and three age-categories (≤40 vs. 41-50 vs. ≥51 years) factorial design. The RM-MANCOVA revealed that perceived digital competence significantly adjusted teachers’ SE-PE and WE values (p<0.001). The analysis yielded a significant multivariate main effect by time (p< 0.001) and by time × age-categories (p=0.001). Follow-up univariate ANCOVA showed significant differences by time in teachers’ SE-PE (p<0.001) and WE (p < 0.001), with a reduction of both values from before to during the lockdown. A Bonferroni post hoc pairwise comparisons showed teachers’ SE-PE significantly decreased in all age categories (p<0.001). The present findings confirm the importance of promoting SE-PE among primary school teachers, regardless of the crisis due to the COVID-19 pandemic. Teachers’ self-efficacy and WE are essential to master the challenges of PE teaching.

Since the 1970s, the application of microprocessor in industrial machinery and the development of computer systems have transformed the manufacturing landscape. The rapid integration and automation of production systems have outpaced the development of suitable human design criteria, creating a deepening gap where human factor was seen as an important source of errors and disruptions. Today the situation seems different: the scientific and public debate about the concept of Industry 4.0 has raised the awareness about the central role humans have to play in manufacturing systems, to the design of which they must be considered from the very beginning. The future of industrial systems, as represented by Industry 4.0, will rely on the convergence of several research fields such as Intelligent Manufacturing Systems (IMS), Cyber-Physical Systems (CPS), Internet of things (IoT), but also socio-technical fields such as social approaches within technical systems. This article deals with different Human dimensions associated with CPS and IoT and focuses on their conceptual evolution of automatization to improve the sociability of such automated production systems and consequently puts again the human in the loop. Hereby, our aim is to take stock of current research trends, and to show the importance of integrating human operators as a part of a socio-technical system based autonomous and intelligent products or resources. As results, different models of sociability as way to integrate human into the broad sense and/or the development of future automated production systems, were identified from the literature and analysed.

The World Health Organization has developed the Integrated Care of Older People (ICOPE) strategy, a program based on the measurement of intrinsic capacity (IC) as “the composite of all physical and mental attributes on which an individual can draw”. Multicomponent interventions appear to be the more effective approach to enhance IC and to prevent frailty and dependence, being adapted physical activity is the preventive intervention that has shown more evidence in the treatment of frailty and risk of falls. The present study aims to describe the development of a multi-domain group-based intervention addressed to frail older people living in the community aimed to improve and/or maintain intrinsic capacity by means of promoting physical activity, healthy nutrition, and psychological wellbeing in frail older people. We used the GUIDED checklist to describe the development process of AMICOPE (Aptitude Multi-domain group-based intervention to improve and/or maintain IC in frail Older PEople). The intervention was built upon the ICOPE framework and it is described with Template for Intervention Description and Replication (TIDieR) guidelines and it includes dietary advice, cognitive stimulation strategies, medication review, goal setting, and activities to strengthen social support and manage depressive symptoms, as well as strength, balance and flexibility exercise using the Vivifrail program. The study represents the first stage of the UK Medical Research Council framework for developing and evaluating a complex intervention. The next step should be carrying out a feasibility study for the AMICOPE intervention, and in a later stage, assessing the effectiveness in a randomized controlled trial.

The slate aggregate has long been perceived as a substandard, low quality waste material with its physical and chemical properties not being competitive with those of the primary aggregates. It is assumed that the slate aggregate particles are not strong, that is not durable and will not compact. This research aims to address those claims and review the available literature on the performance of the slate aggregate. The review inaugurates by analysing the physical, chemical and mechanical properties of slate, before expanding into a literature review of laboratory testing’s on the effect of moisture content on density, compaction and layer thickness of slate aggregate.The paper reviews case studies of construction projects in North Wales, where the slate aggregate has been used for general fill and road building for many years. Some of the case studies include the A55 coastal road and duelling of the A5 in Anglesey (WRAP, 2004), where slate aggregate was successfully used as sub-base. The paper also investigates why many civil engineers are reluctant to use the slate aggregate and regard the material as sub-standard, flaky aggregate. The research paper reviews the potential usages and various products the slate aggregate is suitable for and satisfies the requested standards. The final topic reviewed is the cost of transporting slate aggregate compared with the cost of transport for primary aggregate and the introduction of the Primary Aggregates Tax (Parliament of the United Kingdom, 2011). The last topic includes a critical analyses of the claims that the slate aggregate a commercially viable construction material despite its remote location (Woodward et al, 2004). The transportation cost and the supply chain complexities must be evaluated prior to considering the long-term sustainability of the product (Radanliev et al^1-6, 2014, 2015, 2016).

Integrating triple bottom line (TBL) goals into supply chains (SCs) is a challenging task which necessitates the careful coordination of numerous stakeholders’ individual interests. Recent technological advancements can impact TBL sustainability by changing the design, structure and management of modern SCs. Blockchain technology enables immutable data records and facilitates a shared data view along the supply chain. The Physical Internet (PI) is an overarching framework that can be applied to create a layered and comprehensive view of the SC. In this conceptual paper I define and combine these technologies and derive several high-level research areas and research questions to investigate adoption, management as well as structural SC issues. I suggest a theory-based research agenda for the years to come that exploits the strengths of rigorous academic research, while remaining relevant for the industry. Furthermore, I suggest various well-established theories to tackle the respective research questions and provide specific directions for future research.

Simulation tools capturing the interactions of communication and electrical system operation represent a powerful support for fully assessing the potential benefits and impacts of ICT in future smart power distribution network. A strong interest is upon the possibility of exploiting the last generation communication systems for supporting the transition of distribution network towards a smart grid scenario. Having in mind the above, the authors propose a numerical co-simulation tool useful to thoroughly understand the impact of the communication networks on the performance of whole power system dynamics. The co-simulation tool has been purposely developed to simulate the highly time-critical smart grid application of fault management and network reconfiguration and permits reproducing and evaluating the behavior of the public mobile telecommunication system 4G Long Term Evolution (LTE), as communication technology for smart grid applications. Results of the paper demonstrates that LTE provides good performances for supporting the data communication required to perform fault location, extinction and a subsequent network reconfiguration in smart power distribution networks.

Background: This study aimed to compile and analyze an assortment of research findings concerning potential therapeutic strategies for Myalgic Encephalomyelitis/Chronic Fatigue Syndrome (ME/CFS). The understanding of the multifaceted nature of ME/CFS and the need for varied and personalized therapeutic approaches were central to this investigation.Methods: A comprehensive review and analysis of various studies conducted on ME/CFS was undertaken. These studies covered a wide array of interventions, including pharmacological treatments, nutritional supplements, dietary changes, physical therapies, and lifestyle modifications. The analysis pertained to the effectiveness of these interventions, potential physiological and biochemical markers, and the response of ME/CFS patients to different treatment strategies.Results: The 22 selected papers investigated demonstrated varied responses to the multitude of interventions. While some interventions showed significant improvement in fatigue and biochemical parameters, others found no significant differences between the treated and control groups. Potential physiological and biochemical markers for ME/CFS, such as impaired T cell metabolism, reduced flow-mediated dilation, and decreased work rate at the ventilatory threshold, were highlighted.Conclusion: The findings underscored the complexity of ME/CFS and the need for personalized treatment strategies. Despite mixed results and several limitations, these studies collectively contributed to understanding ME/CFS's complex pathophysiology and treatment, laying the groundwork for future research towards more effective therapeutic strategies for this debilitating disease.

Despite the proliferation of Blockchain Metaverse projects, the inclusion of physically disabled individuals in the Metaverse remains distant, with limited standards and regulations in place. However, the article proposes a concept of the Metaverse that leverages emerging technologies, such as Virtual and Augmented Reality, and the Internet of Things, to enable greater engagement of disabled creatives. This approach aims to enhance inclusiveness in the Metaverse landscape. Based on the findings, the paper concludes that the active involvement of physically disabled individuals in the design and development of Metaverse platforms is crucial for promoting inclusivity. The proposed framework for accessibility and inclusiveness in Virtual, Augmented, and Mixed realities of decentralised Metaverses provides a basis for the meaningful participation of disabled creatives. The article emphasises the importance of addressing the mechanisms for art production by individuals with disabilities in the emerging Metaverse landscape. Additionally, it highlights the need for further research and collaboration to establish standards and regulations that facilitate the inclusion of physically disabled individuals in Metaverse projects.

This article is some review of results that were obtained at 2007-2021 years development of “The Information as Absolute” concept and the informational physical model, which is based on the concept; including a number of fundamental physical problems are briefly considered in framework of the conception and the model. Recently in physics there are several publications, that present lists of the problems. However, those lists are essentially incomplete, for at least two reasons. Firsts of all, a number of phenomena are studied traditionally by philosophy, and so corresponding problems are usually considered to be “metaphysical”. However, they relate also to some concrete physical phenomena. For example, physics evidently studies Matter, and so the metaphysical problems “what is ontology of Matter”, “what is “Space”, “Time” and a few other physical phenomena and notions as well, are really a Meta-physical problems “what does physics study?” There are other fundamental physical problems, which are not considered as such in physics, and are absent in the “fundamental problems lists”. Those include the problems, which really exist, yet are incorporated into standard physical theories, and so are fundamental “implicitly”, which in physics are “solved by default” ‒ and mostly erroneously. Note, though, that a number of “Meta-physical”, and concrete fundamental, problems more in detail are considered in the paper “The Informational Conception and Basic Physics”, https://arxiv.org/abs/0707.4657, v5 (2021), so this paper is, in certain sense, an expanded conclusion of this paper, which includes, correspondingly, more in detail consideration of some more general physical problems; and, besides, in this article, the problem “what are Gravity and Electric Forces” is essentially clarified comparing with the arXiv 2021 paper version above. Besides, the concrete problem “What is Life”, and the rational cosmological model, where a few vague points in standard cosmology rather probably are rationally clarified, while the fundamental problem “matter – antimatter asymmetry” in Matter is solved practically for sure, are considered, and one of recently published rather complete “lists of fundamental problems” is commented in Appendix.

The 2020 Elucidating the role of clouds-circulation coupling in climate - Ocean-Atmosphere (EUREC4A-OA) and Atlantic Tradewind Ocean-Atmosphere Mesoscale Interaction Campaign (ATOMIC) campaigns sought to improve the knowledge of the interaction between clouds, convection and circulation and their function in our changing climate. The campaign consisted of numerous research technologies, some of which are relatively novel to the scientific community. In this study we used a saildrone uncrewed surface vehicle to validate satellite and modelled sea surface salinity (SSS) products in the Western Tropical Atlantic. These products include the Soil Moisture Active Passive (SMAP) Jet Propulsion Laboratory (JPL), SMAP Remote Sensing Systems (RSS), and Hybrid Coordinate Ocean Model (HYCOM). In addition to the validation, we investigated a fresh tongue south east of Barbados. The saildrones accurately depicted the salinity conditions and all satellite and modelled products performed well in areas that lacked small-scale salinity variability. However, SMAP RSS 70 km outperformed its counterparts in areas with small submesoscale irregularities while RSS 40 km was better at identifying small irregularities in salinity such as a fresh tongue. These results will allow researchers to make informed decisions regarding the most ideal product for their application and aid in the improvement of mesoscale and submesoscale SSS products, which can lead to the refinement of numerical weather prediction (NWP) and climate models.

Origins of the time, mass, electric charges and magnetic monopoles are explained. The energies, electric charges and magnetic charges of the particles are defined as E = cDtDV and |q| = cDt = E/DV, and |q_m| = c²Dt, respectively, for the 3-D quantized spaces warped along the time axis direction of ct in the 4-D Euclidean space. The energy (or mass) and charges (or electric charges and magnetic charges) are the vectors along the time axis of ct in the 4-D Euclidean space. This new concept is closely connected to the wave function of the quantum mechanics. The electric charges, magnetic charges and energies have the property of the space direction independence. Magnetic monopoles (charges) are the force carrying bosons with the inside electric field time loop. Electric monopoles are the elementary fermions. Photon space fluctuations are explained with the quantized magnetic charges.

Currently, the most important challenge in any assessment of state-of-the-art sensor technology and its reliability is to achieve road traffic safety targets. The research reported in this paper is focused on the design of a procedure for evaluating the reliability of Internet-of-Things (IoT) sensors and the use of a Cyber-Physical System (CPS) for the implementation of that evaluation procedure to gauge reliability. An important requirement for the generation of real critical situations under safety conditions is the capability of managing a co-simulation environment, in which both real and virtual data sensory information can be processed. An IoT case study that consists of a LiDAR-based collaborative map is then proposed, in which both real and virtual computing nodes with their corresponding sensors exchange information. Specifically, the sensor chosen for this study is a Ibeo Lux 4-layer LiDAR sensor with IoT added capabilities. Implementation is through an artificial-intelligence-based modeling library for sensor data-prediction error, at a local level, and a self-learning-based decision-making model supported on a Q-learning method, at a global level. Its aim is to determine the best model behavior and to trigger the updating procedure, if required. Finally, an experimental evaluation of this framework is also performed using simulated and real data

Background and objectives: Only a few studies analyzed the physical activity level of elderly people living alone in local communities and evaluated the relationship between it and mental health. The purpose of this study was to investigate the relationship between physical activity and depression in the elderly living alone and to provide basic data for the prevention of depression in the elderly. Materials and Methods: We analyzed 256 elderly people living alone aged 65 years or older who completed the 2014 Korea National Health and Nutrition Examination Survey. Depression was defined as a score of 10 or higher using Patient Health Questionnaire-10(PHQ-9). This study investigated walking per week, days of muscular strength exercise performance in the past one week, days of flexibility exercise in the past one week, mean hours in a sitting position per day, the numbers of days and hours conducting a high intensity physical activity in the past one week, and numbers of days and hours conducting a medium intensity physical activity in the past one week to define physical activity. Our study presented prevalence odds ratios (pOR) and 95% confidence interval (CI) by using complex sample logistic regression analysis in order to identify the relationship between physical activity and depression. Results: The results of complex sample logistic regression analysis showed that flexibility exercise was significantly related to depression (p <0.05). On the other hand, the mean hours in a sitting position per day, aerobic physical activity, walking, and muscular strength exercise were not significantly related to geriatric depression. Conclusions: The results of our study implied that persistent flexibility exercise might be more effective to maintain a healthy mental status than muscular strength exercise. A longitudinal study is required to prove the causal relationship between physical activity and depression in the old age.

Cyber Physical Systems (CPS) has been a popular research area in the last decade. The dependability of CPS is still a critical issue, and rare survey has been published in this domain. CPS is a dynamic complex system, which involves various multidisciplinary technologies. To avoid human error and to simplify management, self-management CPS (SCPS) is a wise choice. And to achieve dependable self-management, systematic solution is necessary to verify the design and to guarantee the safety of self-adaptation decision, as well as to maintain the health of SCPS. This survey first recalls the concepts of dependability, and proposes a generic environment-in-loop processing flow of self-management CPS, and then analyzes the error sources and challenges of self-management through the formal feedback flow. Focus on reducing the complexity, we first survey the self-adaptive architecture approaches and applied dependability means; then we introduce a hybrid multi-role self-adaptive architecture, and discuss the supporting technologies for dependable self-management at the architecture level. Focus on dependable environment-centered adaption, we investigate the verification and validation (V&V) methods for making safe self-adaptation decision and the solutions for processing decision dependably. For system-centered adaption, the comprehensive self-healing methods are summarized. Finally, we analyze the missing pieces of the technology puzzle and the future directions. In this survey, the technical trends for dependable CPS design and maintenance are discussed, an all-in-one solution is proposed to integrate these technologies and build a dependable organic SCPS. To the best of our knowledge, this is the first comprehensive survey on dependable SCPS building and evaluation.

Drydocking a ship is essential to the routine maintenance process during its service/operational life. During the drydocking time, various surveys/inspections are carried out per requirements of the classification society, flag administration, and statutory bodies, particularly the underwater items. For shipyards, optimum utilization of drydock capacity (deadweight) is the most considered factor to optimize the physical performance indicators like drydock occupancy rate, capacity utilization rate, and drydock utilization. However, in real life, even after mobilizing all available resources to achieve the optimum usage rate, the overall physical performance could be higher or lower or not up to the expectation. The average size (deadweight) of ships calling to the drydock is observed to be far below the expected capacity, resulting in under-utilization of installed capacity. However, although the drydock occupancy rate is satisfactory, even 100%. For a substantial amount of time, the drydock has been under-utilized in terms of capacity utilization and drydock utilization rate. Drydocking activities of ships in two (2) drydocks of a shipyard are collected and analyzed. Various physical performance indicators (PPIs) are calculated. They are diagnosed year-wise and presented in tabular and graphical form to demonstrate their behavior over the operating period. Authors have investigated the behavior of the above-mentioned physical performance indicators to justify, technically, the selection of capacity of a drydock. A further attempt has been made to propose some recommendations and guidelines from technical viewpoints for the selection criteria of a drydock capacity based on available resources.

Dance is physically demanding, requiring physical fitness(PF) that includes upper body, lower body, core fitness, and balance for successful performance. Whether PF changes as dancers advance from when they enter(freshmen) to when they graduate from their collegiate program(seniors) is unclear. We prospectively compared collegiate dancers’ freshman-to-senior PF. We recorded PF of the upper body strength-endurance(push-ups, n=number), core strength-endurance(front, left-side, right-side, and extensor plank hold times, s=seconds), lower body power(Single-leg-hop-SLH distances % Height; Leg Symmetry Index: LSI=higher/lower*100, %), and balance(Anterior Reach Balance,%Leg-Length, LL; LSI balance=higher/lower*100, %) in 25 collegiate dancers(23 females, 2 males; freshmen age=18.2±0.6yrs). Paired t-tests(p&lt;.05) compared measures from freshmen-senior years. Across their collegiate programs, dancers’ PF remained unchanged: upper body strength-endurance push-ups numbers(p=.93), core strength-endurance plank times(left:p=.44, right:p = .67, front:p=.60, p=.22), SLH distances(left: p =.44, right:p =.85) and SLH symmetry(p=0.16). Dancers’ right leg balance(p =.08) remained similar, while the left balance(p =.02) improved with better symmetry(p&lt;.001) in senior balance scores. Overall, dancers’ PF did not change across their collegiate programs, except for greater left leg balance scores. Findings suggest that practitioners can use collegiate dancers’ freshmen baseline PF when devising rehabilitation programs and making return to activity decisions post injury throughout their dance programs.

Optical fiber sensors based on tapered optical fiber (TOF) structure have attracted a considerable amount of attention from researchers due to the advantages of simple fabrication, high stability, diverse structures, and have great potential for applications in many fields such as physics, chemistry and biology. Compared with ordinary optical fibers, TOF with their unique structural characteristics significantly improve the sensitivity and response speed of fiber-optic sensors and broaden the application range. This review presents an overview of the latest research status and characteristics of fiber-optic sensors and TOF sensors. Then the working principle of TOF sensors, fabrication schemes of TOF structures, novel TOF structures in recent years, and the growing emerging application areas are described. Finally, the development trends and challenges of TOF sensors are prospected. The objective of this review is to convey novel perspectives and strategies for the performance optimization and design of TOF sensors based on fiber-optic sensing technologies.

Peptides of hydrolysates of food proteins are an easily digestible source of amino acids necessary for the body to adapt to physical stress. Commercially significant hydrolysates include whey protein, casein, and other animal proteins. Hydrolysates of plant proteins are gaining popularity, but they are less common, then animal ones. Soy protein isolate is promising for obtaining the hydrolysates due to its affordable price and balanced amino acid profile. However, there are no direct studies showing an improvement in the result of physical activity when eating soy protein isolate hydrolysate (SPIH). In this work, for the first time, the study was conducted on the safety and efficacy of SPIH during physical load on model animals (rats). It was shown that the hydrolysate did not lead to pathological changes in the viscera, food intake, and weight of animals did not differ from the control group (animals consumed whey protein). Under physical load rats enteral fed SPIH showed a tendency to adapt more quickly to physical stress than the control group and the group of animals that was fed by free amino acids. The metabolites of animal blood serum were studied by NMR spectroscopy. It was shown that by the 95th minute after feeding in the group of rats receiving SPIH, the difference of proteinogenic amino acids concentrations in blood between individuals was significantly less than in the groups receiving whey protein or a mixture of amino acids. In other words, individual biochemical and physiological characteristics of individuals did not affect the assimilation of amino acids of hydrolysate.

In a dynamic and rapidly changing world, customers’ often conflicting demands plus fluid economic requirements, often driven by geo-politics, have continued to evolve, out-striping the capability of existing production systems. With its inherent shortcomings, the traditional factory has proven to be incapable of addressing these modern-day manufacturing challenges. Recent advancements in Industry 4.0 have catalyzed the development of new manufacturing paradigms (or smart factory visions) under different monikers (e.g., Smart factory, Intelligent factory, Digital factory, Cloud-based factory etc.) would help fix these challenges. Due to a lack of consensus on a general nomenclature for these manufacturing paradigms, the term Future Factory (or Factory of the Future) is here used as a collective euphemism, without prejudice. The Future Factory constitutes a creative convergence of multiple technologies, techniques and capabilities that represent a significant change in current production capabilities, models, and practices. It is a data-driven manufacturing approach and system that harnesses intelligence from multiple information streams i.e., assets (including people), processes, and subsystems to help create new forms of production efficiency and flexibility. Serving both as a review monograph and reference companion, this paper details the meanings, characteristics, and technological underpinnings of the Future Factory. It also elucidates on the architectural models that guide the structured deployment of these modern factories with particular emphasis on three advanced communication technologies capable of speeding up advancements in the field. It not only highlights the relevance of communication between assets but also lays out mechanisms to achieve these interactions using the Administration shell. Finally, the paper also discusses the key enabling technologies that are typically embedded into bare bone factories to help improve their visibility, resilience, intelligence, and capacity, in addition to how these technologies are being deployed and to what effect. At the onset of the study, we were interested in developing a monograph which would serve as a comprehensive but concise review of general principles, fundamental concepts, major characteristics, key building blocks and implementation guidelines for the Future Factory within the overall context of the manufacturing ecosystem, in the age of Industry 4.0. Our hope is that this paper would enrich the extant literature on advanced manufacturing, help shape policy and research, and provide insights on how some of the identified pathways can be diffused into industry.

Maternal and child nutrition has been a critical component of health, sustainable development, and progress in low- and middle-income countries (LMIC). While a decrement in maternal mortality is an important indicator, simply surviving pregnancy and childbirth does not imply better maternal health. One of the fundamental obligations of nations under international human rights law is to enable mothers and teenage girls to endure pregnancy and delivery as an aspect of their enjoyment of reproductive and sexual health and rights and live a dignified life. The aim of this study was to discover the correlation between the Maternal Observation and Motivation (MOM) program and m-Health support for maternal and newborn health. A Comparative study was done among 109 pregnant mothers (study group-94; control group-102 mothers) with not less than 20 weeks of gestation. Maternal outcomes such as Hb, weight gain and newborn results like birth weight and crown- heel length was obtained on the baseline, 28 and 36 weeks of gestation. Other secondary data collected were abortion, stillbirth, low birth weight, major congenital malformations, twin or triplet pregnancies, physical activity and maternal wellbeing. The MOM intervention included initial face to face education, three in-person visits and eight virtual health coaching by WhatsApp. The baseline data on Hb of the mothers show that 31(32.98%) vs 27(28.72%) of the study and control group had anaemia, which improved to 27.66% and 14.98% among study group mothers at 28 and 36 weeks of gestation (p<0.001). The weight gain (p< 0.001), level of physical activity (p< 0.001), and maternal wellbeing (p< 0.01) also had significant differences after the Intervention. Even after controlling for potentially confounding variables, the maternal food practices regression model revealed that birth weight was directly correlated with consumption of milk (p 0.001), fruits (p 0.01), and green vegetables (p 0.05).As per the physical activity and maternal wellbeing regression model, the birth weight and crown heel length were strongly related with the physical activity and maternal wellbeing of mothers at 36 weeks of gestation (p <0.05). Combining the MOM intervention with standard antenatal care is a safe and effective way to improve maternal welfare while upholding pregnant mothers' human rights.

(1) Aim of the study was to investigate the spatial and temporal characteristics of the airflow created by two commercially available non-contact tonometers, the CorvisST and the Ocular Re-sponse Analyser. (2) The airflow pressure was measured using a MEMS pressure sensor to inves-tigate the spatial and temporal distribution. The airflow from the CorvisST and Ocular Response Analyser were mapped to a 600µm and a 1mm resolution grid, respectively. (3) Central airflow pressure of the CorvisST (96.4 ± 1.4)mmHg was higher than the Ocular Response Analyser (91.7 ± 0.7)mmHg. The duration of the air-puffs also differed, with the CorvisST showing a shorter du-ration (21.483 ± 0.2881)ms than the ORA (23.061 ± 0.1872)ms. The rising edge of the CorvisST airflow pressure profile demonstrated a lower gradient (+8.94mmHg/ms) compared to the Oc-ular Response Analyser (+11.00mmHg/ms). Both had similar decay response edges; CorvisST -11.18mmHg/ms, Ocular Response Analyser -11.65mmHg/ms. (4) The study presents a valid method to investigate physical dimensions of the airflow pressure of non-contact tonometers. Novel findings relating to the magnitude, duration and spatial characteristics of the respective airflow pressures are reported. It is anticipated that this information will better inform clinical studies and theoretical models relating to ocular biomechanics.

Cooperative non-orthogonal multi access communication is a promising paradigm for the future wireless networks because of its advantages in terms of energy efficiency, wider coverage and interference mitigating. In this paper, we study the secrecy performance of a downlink cooperative non-orthogonal multi access (NOMA) communication system under the presence of an eavesdropper node. Smart node selection based on feed forward neural networks (FFNN) is proposed in order to improve the physical layer security (PLS) of a cooperative NOMA network. The selected cooperative relay node is employed to enhance the channel capacity of the legal users, where the selected cooperative jammer is employed to degrade the capacity of the wiretapped channel. Simulations of the secrecy performance metric namely the secrecy capacity ($C_S$) are presented and compared with the conventional technique based on fuzzy logic node selection technique. Based on our simulations and discussions the proposed technique outperforms the existing technique in term the of secrecy performance.

Throughout this paper the effects of injuries on athletes are highlighted in different aspects. Exertional compartment syndrome is a specific injury related to athletes that is thoroughly explored in this paper through an analysis of the anatomy, symptoms, diagnosis and treatments of the syndrome. Exertional compartment syndrome is an exercise-induced muscle and nerve condition that causes pain, swelling as well as disability in the affected muscles of the lower leg. This syndrome commonly develops in young athletes involved in sports with excessive running and repetitive impact such as track and field, soccer, basketball and lacrosse. Exertional compartment syndrome is commonly misdiagnosed as other less severe injuries such as shin splints, which is symptomatic of pain along the tibia bone of the lower leg caused by overuse. The misdiagnosis of exertional compartment syndrome allows the syndrome to worsen and intensify resulting in the only effective treatment to be fasciotomy, a surgical procedure to release the pressure within the compartment of the lower leg. There is no definitive protocol developed for patients after fasciotomy is performed. Athletes experiencing similar symptoms after surgery are usually treated for their symptoms rather than the syndrome as a whole, which does not have a high degree of success. The development of a definitive protocol utilizing the techniques of manual therapy, mobility stretching and corrective strength training can improve the adverse effects of exertional compartment syndrome as well as restore functionality to the athlete. Raising awareness of this syndrome in athletics will be effective in treating the athlete early on in order to avoid severe effects and invasive procedures.

The paper provides a comprehensive review of the recent advancements and methodologies in Human-Robot Collaboration (HRC) applied to the manufacturing assembly process. In modern manufacturing, the assembly process involves intricate and time-consuming operations, often necessitating flexible manual interventions. However, the cost and stability issues associated with manual labor highlight the need for collaborative solutions integrating humans and robots. HRC, as a viable solution, involves the joint effort of humans and robots in manufacturing tasks, presenting advantages in terms of precision, reproducibility, and cycle time. This review categorizes and discusses methodologies such as task allocation, reinforcement learning, and Cyber-Physical Systems (CPS)-based planning approaches that facilitate HRC in the assembly process. It also explores experiments and future trends to address challenges and enhance efficiency in manufacturing assembly through intelligent collaboration between humans and robots. The objective of this research is to provide insights and directions for further research in HRC to optimize manufacturing processes. By analyzing the existing state-of-the-art and presenting future prospects, this paper aims to guide researchers and practitioners toward more effective implementations of HRC in manufacturing assembly, ultimately leading to improved operational efficiency and productivity.

Considering Cu(tda) chelate is a receptor for adenine and related 6-aminopurines, now we report the synthesis, molecular and crystal structures, thermal stability, spectral properties and DFT calculations on the [Cu(tda)(9heade)(H2O)]•2H2O (1). N7 is found to be the preferred donor atom of 9heade, that can favor the cooperation of a Cu-N7(9heade) bond and an (9heade)N6-H•••O(tda) interligand interaction. But unprecedentedly, the Cu(tda)-9heade molecular recognition in 1 is essentially featured the Cu-N1(9heade), without any N6-H•••O(carboxyl tda) interligand interaction. Nevertheless, being N1 the most basic donor for N9-substituted adenines, this Cu-N1 bond is now assisted by an O2-water mediated interaction (N6-H•••O2 and O2•••Cu weak contact). Also in the crystal packing, the O-H(ol) of 9heade interacts with its own adenine moiety by an O3-water mediated interaction (O(ol)-H•••O3 plus O3-H36•••π(adenine moiety). In turn these water-mediated interactions seems to be responsible to serious alterations on the physical properties of crystalline or grounded samples. Density functional theory calculations were used to evaluate the interactions energetically. Moreover, the quantum theory of atoms-in-molecules (QTAIM) in combination with the noncovalent interaction plot (NCIPlot) were used to analyze the interactions and rationalize the existence and relative importance of hydrogen bonding, chalcogen bonding and π-stacking interactions.

Refineries execute a series of interlinked processes, where the product of one unit serves as the input to another process. Potential failures within these processes affect the quality of the end products, operational efficiency, and revenue of the entire refinery. In this context, implementation of a real-time cognitive module, referring to predictive machine learning models, enables to provide equipment state monitoring services and to generate decision-making for equipment operations. In this paper, we propose two machine learning models: 1) to forecast the amount of pentane (C5) content in the final product mixture; 2) to identify if C5 content exceeds the specification thresholds for the final product quality. We validate our approach by using a use case from a real-world refinery. In addition, we develop a visualization to assess which features are considered most important during feature selection, and later by the machine learning models. Finally, we provide insights on the sensor values in the dataset, which help to identify the operational conditions for using such machine learning models.

Different aspects in applying the nucleation theorem to the description of crystallization of liquids are analyzed. It is shown that, by employing the classical Gibbs' approach in the thermodynamic description of heterogeneous systems and assuming that the basic assumptions of classical nucleation theory commonly employed in application to crystallization hold, a general form of the nucleation theorem can be formulated valid not only for one-component but generally for multi-component systems. This result is taken then as the starting point for the derivation of particular forms of this theorem for the cases that the deviation from equilibrium is caused by variations of either composition of the liquid phase, temperature, or pressure. In this procedure, recently developed by us expressions for the curvature dependence of the surface tension, respectively, the dependence of the surface tension on pressure and/or temperature are employed. It is shown that the formulation of the nucleation theorem as proposed by Kashchiev [J. Chem. Phys. 76, 5098-5102 (1982)] holds also for multi-component systems as far as mentioned above assumptions are fulfilled. In the application of classical nucleation theory to crystallization processes it is assumed as one of its basic ingredients that the bulk properties of the critical clusters are widely identical to the properties of the newly evolving crystal phase. This assumption is, however, in general, it is not true. This limitation of the theoretical description can be overcome by the application of the generalized Gibbs approach for the specification of the dependence of the properties of critical crystal clusters on the degree of metastability of the liquid phase. Applying this method, it is demonstrated that a similar formulation of the nucleation theorem as derived based on classical nucleation theory holds true also in cases when a dependence of the state parameters of the critical clusters on the degree of deviation from equilibrium is appropriately accounted for.

This paper introduces a model-free, "on-the-fly" learning control strategy for arrays of energy converters with adjustable generator damping. The devices are arranged so that they are affected simultaneously by the energy medium. Each device uses a different control strategy, of which at least one has to be the machine learning approach presented in this paper. During operation all energy converters record the absorbed power and control output; the machine learning device gets the data from the converter with the highest power absorption and so learns the best performing control strategy for each state. Consequently, the overall network has a better overall performance than each individual strategy. This concept is evaluated for wave energy converter (WEC) with numerical simulations and experiments with physical scale models in a wave tank. In the first of two numerical simulations, the learnable WEC works in an array with four WECs applying a constant damping factor. In the second simulation, two learnable WECs were learning with each other. It showed that in the first test the WEC was able to absorb as much as the best constant damping WEC, while in the second run it could absorb even slightly more. During the physical model test, the ANN showed its ability to select the better of two possible damping coefficients based on real world input data.

proposal for a fundamental theory is described in which classical and quantum physics as a representation of the universe as a gigantic dendrogram are unified. The latter is the explicate order structure corresponding to the purely number-theoretical implicate order structure given by p-adic numbers. This number field was zero-dimensional, totally disconnected, and disordered. Physical systems (such as electrons, photons) are sub-dendrograms of the universal dendrogram. Measurement process is described as interactions among dendrograms; in particular, quantum measurement problems can be resolved using this process. The theory is realistic, but realism is expressed via the the Leibnitz principle of the Identity of Indiscernible. The classical-quantum interplay is based on the degree of indistinguishability between dendrograms (in which the ergodicity assumption is removed). Depending on this degree, some physical quantities behave more or less in a quantum manner (versus classic manner). Ideologically, our theory is very close to Smolin’s dynamics of difference and Rovelli’s relational quantum mechanics. The presence of classical behavior in nature implies a finiteness of the Universe-dendrogram. (Infinite Universe is considered to be purely quantum.) Reconstruction of events in a four-dimensional space type is based on the holographic principle. Our model reproduces Bell-type correlations in the dendrogramic framework. By adjusting dendrogram complexity, violation of the Bell inequality can be made larger or smaller.

The world is currently experiencing the fourth industrial revolution driven by the newest wave of digitisation in the manufacturing sector. The term Industry 4.0 (I4.0) represents at the same time: a paradigm shift in industrial production, a generic designation for sets of strategic initiatives to boost national industries, a technical term to relate to new emerging business assets, processes and services, and a brand to mark a very particular historical and social period. I4.0 is also referred to as Industrie 4.0 the New Industrial France, the Industrial Internet, the Fourth Industrial Revolution and the digital economy. These terms are used interchangeably in this text. The aim of this article is to discuss major developments in this space in relation to the integration of new developments of IoT and cyber physical systems in the digital economy, to better understand cyber risks and economic value and risk impact. The objective of the paper is to map the current evolution and its associated cyber risks for the digital economy sector and to discuss the future developments in the Industrial Internet of Things and Industry 4.0.

Though Cyber Physical Systems (CPS) become very popular in last the decade, dependability of CPS is still a critical issue and related survey is rare. We try to spell out the jigsaw of technologies and figure out the technical trends of dependable self-managing CPS. This survey first recalls the motivation and the similar concepts. By analyzing four generic architectures, we summarize the common characteristics and related assurance technologies, and propose a more generic environment-in-loop processing flow of CPS and a formal interaction flow between physical space and cyber space. Further, the similarity between correctness and dependability is formally analyzed and the new five research questions of dependable self-managing CPS are presented. Then we review the critical technologies and related correctness verification & validation (V&V) methods, the architectures for dependable self-managing CPS. Further, the detail dependability management and V&V technologies are surveyed, which covers the areas of running-time fault management methods and whole life cycle V&V technologies, maintenance and available tool sets. For holistic CPS development, Modeling techniques and MDE (model driven engineering) based V&V methods are analyzed in detail. Then we complete the jigsaw of technologies and figure out the missing part. Further, we propose the technical challenges and the further direction. To our best knowledge, this is the first comprehensive survey on dependable self-managing CPS development and evaluation.

Restraint use in Australian residential aged care has been highlighted by the media, and investigated by researchers, government and advocacy bodies. In 2018, the Royal Commission into Aged Care selected ‘Restraint’ as a key focus of inquiry. Subsequently, Federal legislation was passed to ensure restraint is only used in residential aged care services as the ‘last resort’. To inform and develop Government educational resources, we conducted qualitative research to gain greater understanding of the experiences and attitudes of aged care stakeholders around restraint practice. Semi-structured interviews were held with 28 participants, comprising nurses, care staff, doctors, physiotherapists, pharmacists and relatives. Two focus groups were also conducted to ascertain the views of residential and community aged care senior management staff. Data were thematically analyzed using a pragmatic approach of inductive and deductive coding and theme development. Five themes were identified during the study: 1. Understanding of restraint; 2. Support for Legislation; 3. Restraint-free environments are not possible; 4. Low-level restraint, and 5. Restraint in the community is uncharted. Although most staff, health practitioners and relatives have a basic understanding of restraint, more education is needed at a conceptual level to enable them to identify and avoid restraint practice, particularly ‘low-level’ forms and chemical restraint. There was strong support for the new restraint regulations, but most interviewees admitted they were unsure what the legislation entailed. With regards to resources, stakeholders wanted recognition that there were times when restraint was necessary and advice on what to do in these situations, as opposed to unrealistic aspirations for restraint-free care. Stakeholders reported greater oversight of restraint in residential aged care but stated that community restraint use was largely unknown. Research is needed to investigate the extent and types of restraint practice in community aged care.

Study Objective: This study examined office workstation types’ impact on objective health-related metrics including stress, physical activity (PA), and sleep quality. We propose a sensor-based sleep quality index (SB-SQI) to fill a needed gap for objective sleep quality measurement over short timescales. Methods: We monitored 231 office workers using chest-worn sensors for 72 hours, yielding 11,736 hours of usable data from 163 participants (mean age 43.4, 56% women). SB-SQI was based on a validated algorithm estimating sleep-onset latency, total sleep time, and sleep efficiency, using the scoring method from the Pittsburg Sleep Quality Index (PSQI). We examined the relationships between SB-SQI, office workstation type (open-bench seating, cubicle, and private office), work-hours stress (standard deviation of heart rate variability), and after-work PA (relative duration of moderate-to-vigorous activity). Results: The sensor-derived poor-sleep ratio of the private office workers was higher than with other office workstation types (81% vs. 66.1%, p = 0.023). PSQI revealed a similar but insignificant trend with a lower effect-size. Among good-sleepers, open-bench seating workers had 22% (p = 0.018) less stress during work hours than others. A significant association between work-hours stress and after-work hours PA (r = 0.331, p = 0.000) was observed irrespective of office workstation type, with the highest PA level observed for open-bench seating workers. Conclusions: Office workstation type had a significant impact on work-hours stress, affecting PA after work hours, which influenced sleep quality. SB-SQI could be more sensitive than PSQI in determining the impact of office workstation types on sleep quality.

Hexakis(2-alkoxy-1,5-phenyleneimine) macrocycles were synthesized using a simple one−pot procedure through by precipitation−driven cyclization. The acetal−protected AB−type monomers, 2-alkoxy-5-aminobenzaldehyde diethyl acetals, underwent polycondensation in water or acid−containing tetrahydrofuran. The precipitation−driven cyclization based on imine dynamic covalent chemistry and π−stacked columnar aggregation played a decisive role in the one−pot synthesis. The progress of the reaction was analyzed by MALDI−TOF mass spectrometry. The macrocycles with alkoxy chains were soluble in specific organic solvents such as chloroform, allowing their structures to be analyzed by NMR. The shape−anisotropic, nearly planar, and persistent macrocycles aggregated into columnar assemblies in polymerization solvents, driven by aromatic π−stacking. The octyloxylated macrocycle OcO−Cm6 exhibited an enantiotropic columnar liquid crystal−like mesophase between 165°C and 197°C. In the SEM image of (S)-(−)-3,7-dimethyloctyloxylated macrocycle (−)BCO-Cm6, columnar substances with a diameter of 100−200 nm were observed. The polymerization solution for 2-(2-methoxyethoxy)ethoxy)ethoxylated macrocycle (TEGO−Cm6) gelled and showed thixotropic properties by forming a hydrogen bond network.

Obesity in adolescents combined with the increased exposure time to electronic devices, enhances a sedentary lifestyle and is linked to the risk of developing musculoskeletal injuries. The aim of this study was to identify possible correlations between anthropometric characteristics, body composition, exposure time to electronic devices or screen time (ST) and physical activity (PA) level along with muscle power and dynamic knee valgus (DKV) in young athletes to avoid future injuries. A total of 125 adolescent basketball athletes (66.4% boys), 12 to 17 years old (13.94±1.58 years) participated. Anthropometric and demographic characteristics were recorded. PA level was assessed through IPAQ and ST through a single question from the HELENA study. The Counter Movement Jump test was used for the evaluation of the lower limb muscle power, while the Single Leg Drop Jump test was used for the evaluation of the dynamic knee valgus via two-dimensional (2D) kinematic analysis. The Pearson index showed a statistically significant positive correlation between muscle power and height (r=0.788, p<0.001), while the Spearman index showed a smaller but equally statistically significant positive correlation with BMI (rs =0.651, p<0.001) and age (rs=0.579, p<0.001). The ST (rs= -0.194, p=0.03) showed a weak negative correlation with DKV, while PA (r=0.85, p<0.001) showed a high, statistically significant, positive correlation. The anthropometric characteristics of adolescent athletes can determine their ability to produce muscle power. A high level of physical activity could play a key role in compensating and thus reducing the negative effects of high exposure to screen time on the dynamic knee valgus

Information can be considered as the most fundamental, philosophical, physical and mathematical concept originating from the totality by means of physical and mathematical transcendentalism (the counterpart of philosophical transcendentalism). Classical and quantum information, particularly by their units, bit and qubit, correspond and unify the finite and infinite. As classical information is relevant to finite series and sets, as quantum information, to infinite ones. A fundamental joint relativity of the finite and infinite, of the external and internal is to be investigated. The corresponding invariance is able to define physical action and its quantity only on the basis of information and especially: on the relativity of classical and quantum information. The concept of transcendental time, an epoché in relation to the direction of time arrow can be defined. Its correlate is that information invariant to the finite and infinite, therefore unifying both classical and quantum information.

The COVID-19 pandemic has resulted in a wide range of spatial interventions to slow down the spread of the virus. The spatial limitations of narrow public circulation spaces within informal settlements, which house over one billion people around the world, make it impossible for pedestrians to practice physical distancing (or social distancing). In this paper, we propose a flexible mathematical method, named the Cluster Lane Method, for turning a planar circulation network of any size or complexity into a network of unidirectional lanes, making physical distancing possible in narrow circulation spaces by limiting face-to-face interactions. New notions and theorems about oriented graphs in graph theory are introduced. The paper ends with a discussion of the potential implementation of this cost-efficient, low-tech, sustainable solution, and with the introduction of a novel unidirectional tactile paving for the visually impaired.

Compressive residual stresses in thin films can inhibit crack propagation under normal or sliding contact loading, with associated enhancement of the coating apparent toughness, load bearing capacity and wear resistance. This study investigates the influence of residual stress distributions on the thin film/substrate adhesion using a nanoindenter coupled with scanning electron microscope (SEM) investigations of indentation induced failure modes. Reactive and un-reactive magnetron sputtering with ion plating was used to coat a (100) silicon substrate with aluminum nitride (AlN) with and without an aluminum (Al) adhesion layer. The presence of an Al bond layer gives additional interfacial tensile stress because of the difference in thermal expansion coefficient. Additionally, a different magnitude of residual stresses in the AlN coating was achieved by changing the applied bias voltage onto the substrate. Wafer curvature method and incremental focused ion beam (FIB) milling, combined with high-resolution in situ scanning electron microscopy (SEM) imaging and full field strain analysis by digital image correlation (DIC), were used to measure the average and in-depth stress residual stress distribution in the produced coatings. The adhesion energy was then quantified by using a nanoindentation based model. Results demonstrate that the additional tensile residual stress in the aluminum adhesion layer decrease significantly the coating adhesion, even in presence of a higher compressive stress state in the AlN top-layer. Therefore, the coatings without Al-layer showed better adhesion because of a more homogeneous compressive residual stress in comparison with the coating having Al layer, even though both groups of coatings are produced under same bias voltage. Results are discussed, and some general suggestions are made on the correlation between coating/substrate property combination and the adhesion energy of multilayer stacks. The results suggested that Al bond-layer and inhomogeneous residual stresses affected the adhesion of AlN negatively to a substrate like silicon.

The Gulf Cooperation Council (GCC), locally known as Khaliji, is a group of six Arab nations, including Saudi Arabia, Bahrain, Kuwait, Oman, Qatar, and the United Arab Emirates (UAE). Intimate partner violence (IPV) is a significant public health concern in the GCC region, but the research that synthesized the trend has received scant attention. The present narrative review examines existing research on the prevalence and frequency of IPV among Khaliji women in GCC nations. This review synthesized studies on physical violence, sexual violence, emotional abuse, and controlling behaviors perpetrated by an intimate partner. The prevalence rates of IPV among Khaliji women are observed to be high: women reported facing different types of abuse from their partners, namely physical (7% - 71%), sexual (3.7% - 81%), financial (21.3% - 26%) and psychological (7.5% - 89%), which is a culmination of controlling behavior (36.8%), emotional (22% - 69%) and social violence (34%). The extant studies in the GCC suggest that the most endorsed IPV was psychological abuse (89%) followed by sexual violence (81%). Qualitative content analysis of the associated factors resulted in four meaningful descriptors such as demographics of the victim, sociocultural factors, socioeconomic, and perpetrator-related issues. The study on IPV is still nascent and few. The way forward will require developing culturally appropriate interventions that address unique risk factors for IPV among Khaliji populations, strengthening institutional responses, and increasing awareness and social support for the victim of IPV.

Cognitive impairment in older adults is associated with poor gait performance, physical decline, falls and poor quality of life. This paper analyzes the feasibility and efficacy of a tango-based in-tervention in older people with cognitive impairment living in nursing homes. A multicenter study, with pre and post-test, was carried out. Intervention attendance, well-being, physical abilities (Short Physical Performance Battery), walking performance, functional capacities (Katz Index), and quality of life (Quality of Life in Alzheimer’s Disease) were assessed. Fifty-four participants (84.9 ± 6.7 years, Mini Mental State Examination 14.5 ± 7.4) completed the protocol. Intervention attendance was 92%, and the mean subjective well-being after each session was 4.5 ± 0.5 (on a five-point scale). Statistically significant improvement was found in the quality of life (p = 0.030). Non statistically significant changes were found in walking performance, physical abilities, or in functional capacities. The study shows feasibility and suggests evidence for the effects of Tango therapy on well-being and quality of life. Further studies are necessary to contrast these findings and to verify the role of Tango interventions as a holistic approach to prevent functional decline in older people with cognitive impairment.

Healthy aging among older adults requires the maintenance of good physical and cognitive activity. However, in the natural course of aging, older adults usually experience a decline in their physical and cognitive activity, causing an increasingly sedentary lifestyle. Some older adults may not have a choice but to become increasingly sedentary as they age due to injury or deteriorated physicality. As such they require a manner of assistive technologies to aid in their daily lives and activities to maintain healthy cognitive function. Social Robots are a newer form of assistive technology, specifically designed for social interactions and gameplay. As with other assistive technologies, compliance barriers to the acceptance and use of social robots and types of meaningful, seated activities among older adults are expected. To better explore this phenomenon, improve quality of life and understand what drives older adults to accept and use newer forms of technology like social robots, this research conjoins two conceptual frameworks: The Activity Theory of Aging (ATA) and the Unified Theory of Acceptance and Use of Technology (UTAUT). As social robots hold great promise for improving the quality of life for older adults, exploring what driving factors could enable their greater acceptance and use is essential to furthering this field of study within Australia.

Electric power systems are experiencing relevant changes involving the growing penetration of distributed generation and energy storage systems, the introduction of electric vehicles, the management of responsive loads, the proposals for new energy markets and so on. Such evolution is pushing for a paradigm shift: the management must move from traditional planning and manual intervention to full “smartization” of medium and low voltage networks. Peculiarities and criticalities of future power distribution networks originate from the complexity of the system that includes both the physical aspects of electric networks and the cyber aspects, like data elaboration, feature extraction, communication, supervision and control; only fully integrated advanced monitoring systems can foster this transition towards network automation. The design and development of such future networks require distinct kinds of expertise in the industrial and information engineering fields. In this context, this paper provides a comprehensive review of current challenges and multidisciplinary interactions in the development of smart distribution networks.

Advanced methods of treatment are needed to fight the threats of virus-transmitted deseases and pandemics. Often they are based on an improved biophysical understanding of virus replication strategies and processes in their host cells. For instance, an essential component of the replication of the Hepatitis C virus (HCV) proceeds under the influence of non-structural HCV proteins (NSPs) that are anchored to the endoplasmatic reticulum (ER), such as the NS5a protein. The diffusion of NSPs has been studied by in-vitro fluorescence recovery after photobleaching (FRAP) experiments. The diffusive evolution of the concentration field of NSPs on the ER can be described by means of surface partial differential equations (sufPDE). Knodel et al, Viruses 2018, 10, 28 estimated the diffusion coefficient of the NS5a protein by minimizing the discrepancy of an extended set of sufPDE simulations and experimental FRAP time series data. Here, we provide a scaling analysis of the sufPDEs that describe the diffusive evolution of the concentration field of NSPs on the ER. This analysis provides an estimate of the diffusion coefficient that is based only on the ratio of the membrane surface area in the FRAP region and its contour length. The quality of this estimate is explored by comparison to numerical solutions of the sufPDE for a flat geometry and for ten different 3D embedded 2D ER grids that are derived from fluorescence z-stack data of the ER. Finally, we apply the new data analysis to the experimental FRAP time-series data analyzed in our previous paper, and we discuss the opportunities of the new approach.

The COVID-19 pandemic drew public attention back to the living conditions related to housing, access to green areas in close neighbourhood and nearby recreation. Several studies confirm that visiting green spaces improved the health and wellbeing in times of crisis. This representative study for the metropolitan area of Vienna, Austria’s capital, confirms the high relevance of contact with nature, particularly for citizens to cope with the negative consequences and perceived stress, anxiety, nervousness and many other negative symptoms experienced during the health crisis. It highlights the importance of nearby smaller but also medium to large scale green areas in cities for health and wellbeing of the population. Moreover, it specifically adds novel insights on age effects in use and perception of urban green spaces during COVID-19 pandemic. The online panel survey (n=1012) was conducted in summer 2021. In order to obtain a representative sample reflective of the population’s characteristics, a (stratified) random sample was selected by applying the quota method. The objective was to obtain a sample which represented gender, age and regional distribution of the population of the City of Vienna as well as the immediately surrounding local communities. Interestingly, particularly young people spent more time outside in green areas during the pandemic, discovered novel spaces for the first time and stated a high relevance of contact with nature for their wellbeing. Elderly people above sixty five, on the contrary, stayed more frequently at home. Significant differences are visible between the age groups also with regard to negative symptoms experienced in case of restricted access to green areas due to strict pandemic measures such as lockdowns and quarantine. All age groups, however, similarly acknowledged the importance of green areas for their physical, mental and emotional health in general during the pandemic.

The European Space Agency (ESA) defines as Earth observation (EO) Level 2 information product a single-date multi-spectral (MS) image corrected for atmospheric, adjacency and topographic effects, stacked with its data-derived scene classification map (SCM), whose thematic map legend includes quality layers cloud and cloud-shadow. ESA EO Level 2 product generation is an inherently ill-posed computer vision (CV) problem never accomplished to date in operating mode by any EO data provider at the ground segment. Herein, it is considered: (I) necessary not sufficient pre-condition for the yet-unaccomplished dependent problems of semantic content-based image retrieval (SCBIR) and semantics-enabled information/knowledge discovery (SEIKD) in multi-source EO big data cubes. (II) Synonym of EO Analysis Ready Data (ARD) format. (III) Equivalent to a horizontal policy for background developments in Space Economy 4.0. In compliance with the GEO-CEOS Quality Assurance Framework for EO Calibration/Validation guidelines, to contribute toward filling an analytic and pragmatic information gap from multi-sensor EO big data to timely, comprehensive and operational EO value-adding information products and services, this work presents an innovative AutoCloud+ CV software toolbox for cloud and cloud-shadow quality layer detection in ESA EO Level 2 product. In vision, spatial information dominates color information. Inspired by this true-fact, the inherently ill-posed AutoCloud+ CV software was conditioned, designed and implemented to be “universal”, meaning fully automated (no human-machine interaction is required), near real-time, robust to changes in input data and scalable to changes in MS imaging sensor’s spatial and spectral resolution specifications.

Recently, more wind turbine systems are being installed in deep waters far from the coast. Several concepts of floating wind turbine systems (FWTSs) are developed, among which the semisubmersible platform, due to its applicability in different water depths, good hydrodynamic performance, and facility in the installation process, constitutes the most explored technology compared to the others. However, a significant obstacle to the industrialization of this technology is a design of a cost-effective FWTS, which can be achieved by optimizing the geometry, size and weight of the floating platform, along with the mooring system. This is only possible by selecting a method capable of accurately analyzing the FWTS coupled hydro-aero-structural dynamics at each design stage. Accordingly, this paper aims at providing a detailed overview of the most common coupled numerical and physical methods, including their basic assumptions, formulations, limitations, and costs, used for analyzing the dynamics of FWTSs, mainly those supported by a semisubmersible, to assist the choice of the most suitable method at each design phase of FWTSs. Finally, the article discusses possible future research to address challenges in modeling FWTSs dynamics that persist to date.

The swift progress in low-dimensional nanocarbons, specifically in the realm of the authentic one-dimensional carbon chain featuring sp¹ hybridization, has unveiled exciting prospects for integrating them into cutting-edge technologies across diverse industries. To fully harness their potential, precise control over the growth process is necessary to obtain desired nanostructure and functionality. However, optimizing properties through traditional approaches has been challenging due to complex interactions. To address this, we implement a focused data-driven strategy for nanocarbon inverse design by leveraging a state-of-the-art data-driven nanocarbon genome approach (NCGA). By uncovering relationships between growth parameters and resultant traits, this serves as an expedient catalyst in engineering nanostructures with tailored attributes. We introduce an extensive array of technological approaches aimed at precisely controlling the growth process. These methods encompass stimulating and precisely adjusting synergistic effects, coordinating atomic vibrations at a collective level through the implementation of multilayer nano-interfaces, harnessing the potential of active screen plasma surface engineering, utilizing nano-patterning and allotropic phase transformations, incorporating heteroatom doping, and effectively directing self-assembly. These aim to unlock nanomaterials' latent potential and reveal novel neural pathways within the data-driven NCGA, enhancing its predictive capabilities. Specifically, triggering self-organization during growth can potentially unlock previously unexplored neural pathways. The data-driven NCGA offers a paradigm shift, accelerating discovery and design of nanocarbons with optimized, application-specific properties.

Let β= (((24!)!)!)!, and let {${\mathcal P}_{n^2+1}$} denote the set of all primes of the form {$n^2+1$}. Let ${\mathcal M}$ denote the set of all positive multiples of elements of the set {${\mathcal P}_{n^2+1} \cap (\beta,\infty)$}. The set {${\mathcal X}=\{0,\ldots,\beta\} \cup {\mathcal M}$} satisfies the following conditions: (1) ${\rm card}({\mathcal X})$ is greater than a huge positive integer and it is conjectured that ${\mathcal X}$ is infinite, (2)} we do not know any algorithm deciding the finiteness of ${\mathcal X}$, (3)~a~known and short algorithm for every {$n \in N$} decides whether or not {$n \in {\mathcal X}$}, (4) a known and short algorithm returns an integer~$n$ such that ${\mathcal X}$ is infinite if and only if ${\mathcal X}$ contains an element greater than $n$. The following problem is open: {\em simply define a set {${\mathcal X} \subseteq N$} such that ${\mathcal X}$ satisfies conditions (1)-(4), and \underline{we do not know any representation of~~${\mathcal X}$~~as a finite union of sets whose definitions are simpler than} \underline{the definition of ${\mathcal X}$}} {\tt (5)}. Let {$f(1)=2$}, {$f(2)=4$}, and let {$f(n+1)=f(n)!$} for every integer {$n \geqslant 2$}. For a positive integer $n$, let {$\Psi_n$} denote the following statement: {\em if a system of equations ${\mathcal S} \subseteq \Bigl\{x_i!=x_k: i,k \in \{1,\ldots,n\}\Bigr\} \cup \Bigl\{x_i \cdot x_j=x_k: i,j,k \in \{1,\ldots,n\}\Bigr\}$ has only finitely many solutions in positive integers \mbox{$x_1,\ldots,x_n$}, then each such solution \mbox{$(x_1,\ldots,x_n)$} satisfies {$x_1,\ldots,x_n \leqslant f(n)$}.} We prove that for every statement $\Psi_n$ the bound {$f(n)$} cannot be decreased. The author's guess is that the statements {$\Psi_1,\ldots,\Psi_9$} are true. We prove that the statement $\Psi_9$ implies that the set ${\mathcal X}$ of all {non-negative} integers $k$ whose number of digits belongs to {${\mathcal P}_{n^2+1}$} satisfies conditions {\tt (1)-(5)}.

Formalism proofing general derivation, applying matrix properties operations, showing fundamental relationships with inner product to outer product has been advanced here. This general proof formalism has direct application with physics to quantify quantum density at micro scale level to time commutator at macro scale level. System of operator algebraic equations have been rigorously derived to obtain analytic solutions which are physically acceptable. Extended physics application will include metricizing towards unitarization to achieve gaging Hamiltonian mechanics to electromagnetic gravitational strong theory, towards grand unifying physics atomistic to astrophysics or vice versa via quantum relativistic general physics thereby patching to classical physics fields energy.

Breast Cancer Associated Susceptibility Proteins Type 1/2 (BRCA1/2) promote cellular functioning by modulating NRF2-mediated antioxidant signaling. Redox failure in women with BRCA1/2 insufficiency increases the risk for breast/ovarian/uterine cancers. Risk‐reducing salpingo‐oophorectomy (RRSO) is a prophylactic surgery of the reproductive organs, which is frequently conducted by the age of 40 to lower the occurrence of cancer in women with BRCA1/2 mutations. However, abrupt estrogen decline following RRSO causes ovarian failure, which implicates various cellular physiological processes, resulting in increased release of free radicals and subsequent severe onset of menopausal symptoms. Comfort measures (e.g., hormonal replacement therapy (HRT) and mindfulness-based stress reduction (MBSR)) may improve chronological menopause-related quality of life, but their specific effects are not clear in women with gene mutations. Aiming to fill the gap, this study used path analysis to examine the effects of HRT and MBSR on menopausal symptoms among RRSO patients (N = 199, mean age = 50.5 ± 6.7 years). HRT alleviated menopausal symptoms in BRCA2 carriers and women who were physically active, premenopausal at the time of RRSO, had a high BMI, and had no history of breast cancer. It increased the severity of urogenital symptoms in those with a history of cancer. MBSR, on the other hand, was associated with increased intensity of most menopausal symptoms. The results suggest that young women undergoing recent RRSO may benefit from HRT at an individual level while their need for extensive measures to optimize their psychological wellbeing is ongoing. Adverse effects of MBSR, which are captured in the present study imply that MBSR may interfere with redox sensitivity associated with estradiol fluctuations in BRCA1/2 carriers. Investigations are needed to test this hypothesis and elaborate on the underlying mechanisms in those women.