The stability of deep soft rock tunnels is of particular concern under seepage conditions. Aiming at thoroughly discussing the seepage actions and their consequences on the support scheme of such structures, the host rocks of the Weilai Tunnel situated in Guangxi province of China are taken as the research substance. Emphasizing on seepage conditions, stresses, displacements and plastic zone radii along the surrounding rocks of such tunnel are adequately examined taking into consideration the Mogi-Coulomb strain criterion and the elastic-plastic theory. Subsequently, based on strain-softening model, the coupled actions of seepage and softening on the rocks surrounding the tunnel are studied. According to the results, it is revealed that the support scheme of deep soft rock tunnels must be of highest resistance possible to better decrease the plastic zone and the tangential stress along the host rocks. Moreover, throughout the surrounding rocks, the dissemination of pore water pressure is strongly affected by the uneven permeability coefficient under anisotropic seepage states. Combined effects of softening and seepage are very dangerous for the surrounding rocks of deep-buried tunnels. To better guarantee reasonable longevity of such tunnels, long-term monitoring of their support structures with reliable remote sensors is strongly recommended.

The Wind Energy Conversion System (WECS) plays an inevitable role across the world. In particular, the attention for Permanent Magnet Synchronous Generators (PMSGs) connected with wind farm is popular. This paper deals with the literature review that describes the recent advances, progresses and innovatory trends on PMSGs for WECS. Comparison between geared and direct-driven conversion systems and the classification of electrical machines used in WECS are discussed. A detailed analysis on the design aspects considering various topologies of PMSGs are encompassed in the literature. The PMSG design and optimization problems are solved by field computation techniques and optimized by using Soft Computing (SC) techniques .The three-dimensional, finite element software platform for the analysis and design of PMSGs is discussed. This paper also deals with the interdisciplinary modeling, analysis, and optimization of PMSG using Finite Element Analysis (FEM) and SC techniques. Finally, PMSGs are reviewed and compared for further exploration.

The present review compared the efficacy of soft tissue substitutes (STS) and autogenous free gingival graft (FGG) or connective tissue graft (CTG) in mucogingival procedures to increase keratinized tissue (KT) width around teeth and implants. Two independent examiners performed the electronic search on Medline and Cochrane Library based on the following PICO’s format: (P) adult patients; (I) soft tissue substitutes and FGG/CTG; (C) STS vs CTG; STS vs FGG; STS vs CTR; (O) KT width gain; (S) Systematic Reviews, Randomized Controlled Trials. Results showed that around teeth, all biomaterials showed superior performance compared to CAF alone for treating gingival recessions. However, when compared to CTG, ADM yields the most similar outcomes to the gold standard (CTG), even though in multiple recessions CTG still continue to be considered the most favorable approach. Use of STSs (acellular matrix or tissue engineered) in combination with an apically positioned flap resulted in a significantly less gain of KTW compared to what achieved with FGG and APF. Around dental implants, free gingival grafts were deemed more effective than soft tissue substitutes in enhancing keratinized mucosa width.

The Spiking Neural Network (SNN) has attracted more and more attention recently. It adopts binary spike signals to transmit information. Benefitting from the information passing paradigm of SNNs, the multiplications of activations and weights can be replaced by additions, which are more energy-efficient. However, its ``Hard Reset" mechanism for the firing activity would ignore the difference among membrane potentials when the membrane potential is above the firing threshold, causing information loss. Meanwhile, quantifying the membrane potential to 0/1 spikes at the firing instants will inevitably introduce the quantization error thus bringing about information loss too. To address these problems, we propose to use the ``Soft Reset" mechanism for the supervised training-based SNNs, which will drive the membrane potential to a dynamic reset potential according to its magnitude, and Membrane Potential Rectifier (MPR) to reduce the quantization error via redistributing the membrane potential to a range close to the spikes. Results show that the SNNs with the ``Soft Reset" mechanism and MPR outperform their vanilla counterparts on both static and dynamic datasets.

Traumatic myiasis is a parasitic infestation resulting from feeding fly larvae in traumatic lesions in the cutaneous tissues of vertebrate hosts. Species that cause traumatic myiasis are found in the families Calliphoridae and Sarcophagidae. This study evaluated the traumatic myiasis cases detected during examining animals brought to Dicle University Wildlife Rescue, Rehabilitation, Training, Practice, and Research Center with wound complaints between 2020-2022. Species determinations of the larvae collected from traumatic myiasis cases were detected in five different animals were made as morphological and molecular, and four species were detected, including Lucilia sericata, Wohlfahrtia magnifica, Calliphora vicina, and Calliphora vomitria. We report a case of traumatic myiasis in the Euphrates softshell turtle and Wild goat for the first time. In order to reduce the exposure of wild animals to traumatic myiasis, new strategies for fly control need to be developed.

Necrotizing fasciitis is a life-threatening soft-tissue infection affecting the deep fascia and subcutaneous tissue. It is characterized by a fulminant course and high mortality rates. NF of the head and neck is very rare, most cases being odontogenic in origin. Streptococcus spp. and Staphylococcus spp. are the most common isolated organisms. If the infection progresses to descending mediastinitis the prognosis becomes very poor. Since the initial clinical features can be similar to those of a non-necrotizing deep cervical infection, a high degree of suspicion is critical for an early diagnosis. Computed tomography scan can be useful in the diagnosis and to define the extent of the infection. Early and aggressive surgical debridement of all compromised tissue and antibiotic therapy and fluid resuscitation are essential and should not wait for bacterial culture results. Despite prompt and adequate treatment, mortality of CNF can be as high as 35%.

This study aimed to obtain and characterize extracted hemp oil enriched in cannabidiol (CBD) by decarboxylation of cannabidiolic acid (CBDA) and to give new insights into its antioxidant and anticancer effects. Optimization of CBDA decarboxylation in hemp oil was performed, and CBD and CBDA contents and purities were determined by “flash chromatography”, 1H- and 13C-NMR. The antioxidant properties of CBD-enriched oil were investigated by Fe2+ chelating activity, Fe3+ reducing antioxidant power assay, O2− scavenging activity, HO− scavenging ability and lipid peroxidation inhibitory assay and its cytotoxicity, apoptosis- and oxidative stress-inducing effects on NHDF, MeWo, HeLa, HepG2 and HOS cells were determined. The CBD concentration in hemp oil was increased by CBDA soft decarboxylation optimized at 90°C, for 1 h and resulted oil was capable of reducing iron, scavenging free radicals, and inhibiting lipid peroxidation in cell-free oxidative conditions. CBD-enriched oil promoted NHDF proliferation at up to 15 µg CBD/mL, while inducing apoptosis and ROS production and modulating antioxidant enzymes’ gene expression in cancer cells, being selective for osteosarcoma cells and induced apoptosis by p53- and ROS-independent mechanisms. CBD-enriched hemp oil demonstrated antioxidant properties in oxidative conditions and promoted normal fibroblasts’ proliferation, while inducing apoptosis and ROS production in cancer cells.

University-Business partnership for collaborative curriculum design, development and delivery is possibly the less explored dimension of University Business Collaboration (UBC). Even if some models for curricular design and development might be available, scarce information exists on how the partnership is constructed, the new curricula are designed, developed and how they are implemented. This article intends to present and discuss the experience obtained during a three-year European funded Project, namely Think4Jobs. This project exemplifies the significance and benefits of UBC in the design, development and delivery of curricula that meet the evolving demands of the labour market while promoting Critical Thinking (CT) as a foundational 21st century skill to contribute to graduates' employability. Think4Jobs project brought together a multidisciplinary team of researchers and business organisations from five European countries (Germany, Greece, Lithuania, Portugal and Romania) with interests in promoting and developing CT and mitigating eventual competence gaps. The project's success was attributed to key practices, including defining a common conceptualization of CT, employing participatory co-design, and providing common training for university and business partners. Clear objectives, explicit roles, effective communication, and ongoing evaluation further enhanced the collaboration. Experiential learning, real-work problems, and case studies reinforced the curricula, bridging the gap between academia and the labour market. By embracing these insights, future UBC initiatives can empower graduates with the necessary skills to stand out in an ever-changing labour market, contributing to enhanced education and successful careers.

This paper presents a control algorithm for soft-switching series LC converters. The conventional voltage-to-voltage controller is split into a master and a slave controller. The master controller implements constant-current-constant-voltage (CCCV) control, required for demanding applications, i.e. lithium battery charging or laboratory power supplies. It defines the set-current for the open-loop current slave controller, which generates the PWM parameters. The power supply achieves fast large-signal responses, e.g. from 5 V to 24 V, where 95% of the target value is reached in less than 400 µs. The design is evaluated extensively in simulation and on a prototype. A consensus between simulation and measurement is achieved.

Due to the highly nonlinear, multi-stage, and strongly time-varying marine lysozyme fermentation process, it is difficult to assure the stability and prediction accuracy of the traditional single global soft sensor model on a global scale. This study innovatively proposed a soft sensor model based on an improved seagull optimization algorithm (ISOA) combined with Gaussian process regression (GPR) weighted ensemble learning. First, the sample data set is divided into multiple local sample subsets by the improved density peak clustering algorithm (ADPC). Second, the Gaussian process regression model is optimally altered with an improved seagull optimization algorithm for the purpose of establishing the corresponding sub-prediction model. Finally, the prediction model's fusion strategy is ultimately determined depending on the degree of connection between the test samples and a subset of local pieces. Simulation results show that the proposed soft sensor model, which searches GPR based on ISOA and combines various sub-models, can predict the key biochemical parameters of the marine lysozyme fermentation process better with less prediction error under the condition of fewer training data, and it can be expanded to the soft sensor models of general nonlinear systems, according to simulation results.

Dielectric elastomer actuators (DEAs) offer robust, high energy density solutions for soft robotics. The proposed end effector consists of three spring roll configuration DEAs, each acting as a robotic finger, using a 3M VHB-F9473PC adhesive membrane. The lateral force, bending angle and response time of the actuator are measured experimentally and compared with the predictions of an analytical model. The cylindrical actuator measures 70 mm in length and 15 mm in diameter and achieved a lateral force of 30 mN, a bending angle of 6.8 ° and a response time of ≈ 1 s. Spring roll configuration DEAs are shown to reduce the effects of viscoelasticity seen in the membrane, making the actuator more controllable at higher voltages. The dielectric constant of the membrane is shown to be a limiting factor of actuation, with a decrease in dielectric constant resulting in larger actuation. The end effector successfully gripped numerous light objects for extended periods, showing the applicability of spring roll DEAs for soft end effectors.

Background. Shoulder in CrossFit should have a balance between mobility and stability. Glenohumeral internal rotation deficit and posterior shoulder stiffness are risk factors for overhead shoulder injury. Objective. To determine the effectiveness of instrument assisted soft tissue mobilization and horizontal adduction stretch in CrossFit practitioners’ shoulders. Methods: Twenty-one regular CrossFitters were allocated to experimental (stretching with isometric contraction and instrument assisted soft tissue mobilization) or control group (instrument assisted soft tissue mobilization). Each session lasted 5 minutes, 2 days a week, over a period of 4 weeks. Shoulder internal rotation and horizontal adduction (digital inclinometer), and posterior shoulder stretch perception (Park scale) were evaluated. Shapiro-Wilk test was used to analyze the distribution of the sample. Parametric student's t-test was used to obtain the intragroup differences. The inter- and intra-rater differences were calculated using a repeated measures ANOVA. Results. Changes were found in the experimental group following intervention (p < 0.05), and when comparing baseline and follow-up assessments (p < .05) in all variables. Significant differences were found in the control group following intervention (p < 0.05), in right horizontal adduction and left internal rotation. When comparing perception of internal rotation and horizontal adduction in both groups in the three assessments significant differences were found. Conclusions. Instrument assisted soft tissue mobilization can improve shoulder horizontal adduction and internal rotation. An instrument-assisted soft tissue mobilization technique yields the same results alone as those achieved in combination with post-isometric stretch with shoulder adduction.

In this paper, a recent meta-heuristic optimization algorithm called the discrete-continuous hyper-spherical search algorithm is used to solve the mixed-integer nonlinear problem of soft open points (SOPs) and renewable distributed generators allocation along with new network reconfiguration methodology under different loading conditions to minimize the total power loss in balanced distribution systems. Multi-scenario studies, which aim to improve the investigation of the overall performance of the strategies, are conducted on IEEE 33-node and 83-node balanced distribution systems. The contributions of SOP losses to the total active losses, as well as the effect of increasing the number of SOPs connected to the system, are investigated to determine the real benefits gained from their allocation. The results obtained validate, with proper justifications, the effectiveness of allocating both SOPs and renewable distributed generators with the proposed network reconfiguration methodology to provide the best operation of distribution networks with minimum losses and enhanced power quality performance. It was also shown that SOPs successfully assist the growing integration plans of the renewable distributed generators units and can address issues related to voltage violations and network losses efficiently.

Cells take decisions on their responses depending on the stimuli received by the surrounding extracellular environment, that provides the essential cues at the micro and the nano-lengthscales required for adhesion, orientation, proliferation and differentiation. In this study, discontinuous microcones on silicon (Si) and continuous microgrooves on polyethylene terephthalate (PET) substrates were fabricated via ultrashort-pulsed laser irradiation at various fluences, resulting in microstructures with different roughness and geometrical characteristics. The topographical models attained were specifically developed to imitate the guidance and alignment of Schwann cells for oriented axonal regrowth, towards nerve regeneration. At the same time, positive replicas of the silicon microstructures formed were successfully reproduced, via soft lithography, on the biodegradable polymer poly(lactide-co-glycolide) (PLGA). The anisotropic continuous (PET) and discontinuous (PLGA replicas) microstructured polymeric substrates were assessed in terms of their influence on the Schwann cells responses. It is shown that the developed micropatterned substrates enable control over the cellular adhesion, proliferation and orientation and are thus useful to engineer cell alignment in vitro. This property could be potentially useful in the fields of neural tissue engineering and for dynamic microenvironment systems that simulate in vivo conditions.

The paper proposes a human explainable artificial intelligence approach for mapping the status of environmental phenomena from multisource geo data. It is both knowledge and data driven: it exploits remote sensing expert’s knowledge to define the contributing factors from which partial evidence of the environmental status can be computed. Furthermore, it aggregates the partial evidences to compute a map of the environmental status by adapting to a region of interest through a learning mechanism exploiting Volunteered Geographic Information (VGI), both from in situ observations and photointerpretation. The approach is capable to capture the specificities of local context as well as to cope with the subjectivity and incompleteness of expert’s knowledge. The proposal is exemplified to map the status of standing water areas (i.e. water bodies and river, human driven or natural hazard flooding) by considering satellite data and geotagged observations. Results of the validation experiments were performed in three areas of Northern Italy, characterized by distinct ecosystems. Results of the proposed methodological framework showed better performances than traditional approaches based on single spectral indexes thresholding. The use of expert’s knowledge, possibly imprecise/uncertain and incomplete, the need of few ground truth data for learning, and finally the explainability of learned rules are the distinguishing characteristics of the proposal with respect to traditional machine learning methods.

In the current natural environment, due to the complexity of the background and the high similarity of the color between immature green tomato and plant, the occlusion of the key organs (flower and fruit) by the leaves and stems will lead to low recognition rate and poor generalization of the detection model. Therefore, an improved tomato organ detection method based on convolutional neural network has been proposed in this paper. Based on the original Faster R-CNN algorithm, Resnet-50 with residual blocks was used to replace the traditional vgg16 feature extraction network, and K-means clustering method was used to adjust more appropriate anchor size than manual setting to improve detection accuracy. A variety of data augmentation techniques were used to train the network. The test results showed that compared with the traditional Faster R-CNN model, the mean average precision (mAP) of the optimal model was improved from 85.2% to 90.7%, the memory requirement decreased from 546.9MB to 115.9 MB, and the average detection time was shortened to 0.073S/sheet. As the performance greatly improved, the training model can be transplanted to the embedded system, which lays a theoretical foundation for the development of precise targeting pesticide application system and automatic picking device.

The clinical requirement for a good esthetic result for immediate implant placement is the absence of dehiscence in the anterior facial alveolar bone. In the presence of a dehiscence, it is recommend-ed to use a connective tissue graft in addition to immediate implant placement or to change to ear-ly implant placement. However, the literature focusing on dehiscence is scarce, and the influence of different placement times and combined use of connective tissue graft on postoperative esthetics in cases with dehiscence is unclear. Therefore, we quantitatively evaluated the pre-extraction de-hiscence morphology and postoperative changes in the facial tissue of implants in three groups: immediate implant placement (Group I), immediate implant placement with connective tissue graft (Group IC), and early implant placement (Group E). Fifty-two implants were obtained (20 in Group I, 16 in Group IC, and 16 in Group E). A wider dehiscence increases the risk of soft tissue regression, which was one reason for choosing early implant placement. A combination of imme-diate implant placement and connective tissue graft, or early implant placement, tended to result in less soft tissue regression due to the thicker postoperative facial soft tissue volume.

The time-dependent behavior and long-term stability of deep-buried tunnels in soft rocks have received lots of considerations in tunnel engineering and allied sciences. To better explore and deepen the engineering application of rock creep, extensive research studies are still needed, although fruitful outcomes have already obtained in many related investigations. In this article, the Weilai Tunnel in China’s Guangxi province is studied taking its host rocks as the main research object. In fact, aiming at forecasting the time-varying deformation of this tunnel, a novel elasto-visco-plastic creep constitutive model with two variants is proposed, by exploiting the typical complex load-unload process of rock excavation. The model is well validated and good agreements are found with the relevant experimental data. Moreover, the time-dependent de-formation rules are properly established for the surrounding rocks, by designing two new closed-form solutions based on the proposed creep model and the Hoek-Brown criterion. The convergence deformations calculated from the closed-form solutions conform well to the on-site monitoring data. In only 27 days after excavation, the creep deformation of the Weilai tunnel overtakes 400 mm, which is enormous. To guarantee the long-term stability of this tunnel, a ro-bust support scheme and its long-term monitoring with appropriate remote sensors are strongly suggested.

Background: PRAME, NY-ESO-1 and SSX2 are cancer testis antigens (CTAs), which in normal tissues are expressed in testicular germ cells with re-expression in numerous cancer types. Their ability to elicit humoral and cellular immune responses have rendered them promising targets for cancer immunotherapy, but they have never been studied in a large and well-characterized cohort soft tissue sarcomas (STS). Methods: On protein level, we examined PRAME, NY-ESO-1 and SSX2 expression in tumour tissues of 249 STS using immunohistochemistry. We correlated expression levels with clinicopathological parameters including Tumour-infiltrating lymphocyte (TIL) counts, grading and long- term survival. Results: Expression of PRAME, NY-ESO-1 and SSX2 was observed in 25 (10%), 19 (8%), and 11 (4%) of 249 specimens with distinct patterns for histo subtypes. Expression of PRAME was associated with shorter patient survival (p=0.005) and higher grade (G2 vs G3, p=0.001) while NY-ESO-1 expression was correlated with more favourable survival (p=0.037) and low grade (G2 vs G3, p=0.029). Both PRAME and NY-ESO-1 expression was more frequent in STS with low TILs counts. Conclusions: CTAs PRAME, NY-ESO-1 and SSX2 show distinct expression patterns in different STS subtypes. These results may guide future immunotherapeutic approaches in STS.

In this paper, we present a framework that automatically labels Latent Dirichlet Allocation (LDA) generated topics using sentiment and aspect terms from COVID-19 tweets to help the end-users by minimizing the cognitive overhead of identifying key topics labels. Social media platforms especially Twitter are considered as one of the most influential sources of information for providing public opinion related to a critical situation like the COVID-19 pandemic. LDA is a popular topic modelling algorithm that extracts hidden themes of documents without assigning a specific label. Thus automatic labelling of LDA-generated topics from COVID-19 tweets is a great challenge instead of following the manual labelling approach to get an overview of wider public opinion. To overcome this problem, in this paper, we propose a framework named \texttt{SATLabel} that effectively identifies significant topic labels using \textit{top unigrams features of sentiment terms and aspect terms clusters from LDA generated topics} of COVID-19 related tweets to uncover various issues related to the COVID-19 pandemic. The experimental results show that our methodology is more effective, simpler, and traces better topic labels compare to the manual topic labelling approach.

An attractive option for realizing applications in radiation environments is to employ All-Programmable System-on-Chips (APSoCs) thanks to their high-performance computing and power efficiency merits. Despite APSoC's advantages, like any other electronic device, they are prone to radiation effects. Processors found in APSoCs must, therefore, be adequately hardened against ionizing-radiation to become a viable alternative for harsh environments. This paper proposes a novel triple-core lockstep (TCLS) approach to secure the Xilinx Zynq-7000 APSoC dual-core ARM Cortex-A9 processor against radiation-induced soft errors by coupling it with a MicroBlaze TMR subsystem in Zynq's programmable logic (PL) layer. The proposed strategy uses software-level checkpointing principles along with roll-back and roll-forward mechanisms (i.e. software redundancy), and hardware-level processor replication as well as checker circuits (i.e. hardware redundancy). Results of fault injection experiments show that the proposed solution achieved high soft error security by mitigating about 99% of bit-flips injected into both ARM cores' register data.

Detection of human movement requires lightweight, flexible systems to detect mechanical parameters (like strain and pressure) not interfering with user activity, and that he/she can wear comfortably. In this work we address such multifaceted challenge with the development of smart garments for lower limb motion detection, like a textile kneepad and anklet in which soft sensors and readout electronics are embedded for detecting movement of the specific joint. Stretchable capacitive sensors with a three-electrode configuration are built combining conductive textiles and elastomeric layers, and distributed at knee and ankle. They show an excellent behavior in the ~30% strain range, hence the correlation between their responses and the optically tracked Euler angles is allowed for basic lower limb movements. Bending during knee flexion/extension is detected, and it is discriminated from any external contact by implementing in real time a low computational algorithm. The smart anklet is designed to address joint motion detection in and off the sagittal plane. In this work, ankle dorsi/plantar flexion, adduction/abduction, and rotation are retrieved. Both smart garments show a high accuracy in movement detection, with a RMSE less than 4° in the worst case.

In this article, the effect of substitution of Zr and Ga in Dy2Fe17 prepared by arc melting technique are studied. The substitution of Zr and Ga in Dy2Fe17 was found to have an important effect on their structure and magnetic properties. The Rietveld analysis conformed that the crystalline system wereTh2Ni17 structure. Lattice parameters a (Å) and c (Å), unit cell volume (Å3), bonding distance (Å) were calculated by using Rietveld analysis. The unit cell volume of Dy2Fe17-xZrx and Dy2Fe16Ga1-xZrx increase linearly with the Zr and Ga substitution. The substitution of Zr and Ga are limited up to x=1 in order to avoid the decrease in saturation magnetization. The Curie temperature (Tc) of Dy2Fe17-xZrx and Dy2Fe16Ga1-xZrx are found to be Zr content dependent. The Curie temperature is found to be increasing first and then decrease for higher Zr content. The maximum curie temperature was observed 510K at x = 0.75 for Dy2Fe17-xZrx and 505.1 K at x = 0.5 for Dy2Fe17-xZrx which are102 K and 97 K higher than Dy2Fe17. The room temperature Mössbauer analysis shows the decrease in average hyperfine field and increase in isomer shift with Zr doping.

The development of novel coherent and brilliant sources, such as soft X-ray Free Electron Laser (FEL) and High Harmonic Generation (HHG) enables new ultrafast analysis of the electronic and structural dynamics of a wide variety of materials. Soft X-ray FEL delivers high brilliance beams with short pulse duration, high spatial coherence and photon energy tunability. In com-parison with FELs, HHG X-ray sources are characterized by a wide spectral bandwidth and few to sub-femtosecond pulses. The approach will lead to time-resolved reconstruction of molecular dynamics, shedding light on different photochemical pathways. The high peak brilliance of soft X-ray FELs facilitates investigations in nonlinear regime, while the broader spectral bandwidth of the HHG sources may provide the simultaneous probing of multiple components. Significant technical breakthroughs in these novel sources are under way to improve brilliance, pulse dura-tion, and to control spectral bandwidth, spot size, and energy resolution. Therefore, in the next few years, the new generation of soft X-ray sources combined with novel experimental tech-niques, new detectors, and computing capabilities will allow the study of several extremely-fast dynamics, such as vibronic dynamics. In the present review, we shortly discuss recent devel-opments in experiments, performed with soft X-ray FELs and HHG sources, operating near car-bon K-absorption edge, being a key atomic component in biosystems and soft materials. Differ-ent spectroscopy methods such as time-resolved pump-probe techniques, nonlinear spectrosco-pies and photoelectron spectroscopy studies have been addressed in an attempt of a better un-derstanding of fundamental physico-chemical processes

With the rise of internet technology and the growth of mobile communications, the global economy has undergone a significant transformation, shifting towards digital and soft markets. As a result, great efforts have been made to establish virtual marketplaces that provide customers with an exceptional shopping experience. One crucial aspect of this new paradigm is marketing, which has led to the emergence of a new stage known as E-marketing. In E-marketing, understanding customer behavior is of utmost importance. Marketing teams and companies are eager to gain insights into how different customer segments react to their products. Marketing strategies are now developed based on customer information such as financial status, location, age, gender, and more. As a result, the abundance of customer data generated by these new commerce technologies has surpassed the capabilities of traditional data analysis methods. To extract valuable knowledge from this vast amount of data, data mining technologies have come into play. Techniques such as clustering, classification, and prediction are utilized to mine marketing data and uncover hidden patterns and trends. The impact of data mining on E-marketing has been the subject of analysis in this study. A questionnaire-based review was conducted to collect the necessary data, which was then analyzed using SPSS 23 software. The study's results demonstrate that data mining can significantly enhance the performance of E-marketing by providing intelligent and efficient predictions of customer behaviour. Moreover, this technology offers similar advantages for end-customers as well. By leveraging the power of data mining, companies can gain valuable insights, tailor their marketing efforts, and ultimately provide better products and services to their customers in the digital marketplace.

Scaffold guided breast tissue regeneration (SGBTR) can both transform reconstructive and cosmetic breast surgery. Implant-based surgery is the most common method. However, there are inherent limitations as there is replacement of tissue rather than regeneration. Regenerating autologous soft tissue has the potential to provide a more like-for-like reconstruction with minimal morbidity. Our SGBTR approach regenerates soft tissue by implanting additively manufactured bioresorbable scaffolds filled with autologous fat graft. A pre-clinical large animal study was conducted implanting 100 ml breast scaffolds (n=55) made from medical-grade polycaprolactone in 11 minipigs for 12 months. Various treatment groups were investigated where immediate or delayed autologous fat graft, as well as platelet rich plasma were added to scaffolds. Computed Tomography and Magnetic Resonance Imaging was performed on explanted scaffolds to determine volume and distribution of regenerated tissue. Histological analysis was performed to confirm tissue type. At 12 months we were able to regenerate and sustain a mean soft tissue volume of 60.9 4.5 ml (95% CI) across all treatment groups. There was no evidence of capsule formation. There were no immediate or long-term post-operative complications. In conclusion, we were able to regenerate clinically relevant soft tissue volumes utilizing SGBTR in a pre-clinical large animal model.

Skin and soft-tissue infections (SSTI) are common cases of hospital-acquired infections with aetiologic agents exhibiting antimicrobial resistance (AMR). We determined the prevalence, proportion of laboratory-investigated cases, AMR-profiles, and factors associated with SSTI and multi-drug resistance (MDR). This study was based on archived data of patients suspected of SSTI from 2019-2021 at Jinja Regional Referral Hospital. The analysis involved 268 randomly selected patient reports. Prevalence of SSTI was 66.4%. Laboratory-investigated cases were 14.11%. Staphylococcus aureus (n=51) was the most isolated organism. MDR pathogens explained 47% of infections. Methicillin-resistant S. aureus was up to 44%. In addition, 61% of Gram-negatives had the potential to produce extended-spectrum beta-lactamases, while 27% were non-susceptible to carbapenems. Ward of admission was significantly associated with infection (aPR=1.78, 95% CI: 1.003-3.18, p-value=0.04). Age category (19-35) was an independent predictor for MDR infections (aPR=2.30, 95%CI:1.02-5.23, p-value=0.04). The prevalence is relatively high with MDR pathogens responsible for almost half of the infections. Routine use of culture and sensitivity testing should be done for proper infection management. Gentamicin and ciprofloxacin can be considered for empirical management of emergency SSTI suspected of S. aureus. Recognizing SSTI under the Global Antimicrobial resistance Surveillance System would lead to improved preparedness and response to AMR.

One of the frequently used classes of the sparse reconstruction algorithms is based on the iterative shrinkage/thresholding procedure, where the thresholding parameter controls a trade-off between the algorithm accuracy and the execution time. In order to avoid this trade-off, we propose using a fast intersection of confidence interval method in order to adaptively control the threshold value through the reconstruction algorithm iterations. We have upgraded the two-step iterative shrinkage thresholding algorithm with a such procedure, improving its performance. The proposed algorithm, denoted as the FICI-TwIST, along with a few selected state-of-the-art sparse reconstruction algorithms have been tested on the classical problem of image recovery by emphasizing the image sparsity in the discrete cosine and the discrete wavelet domain. Furthermore, we have derived a single wavelet transformation matrix which avoids wrapping effects achieving significantly faster execution times when compared to more traditional function based transformation. The obtained results indicate competitive performance of the proposed algorithm, even in cases where all algorithm parameters have been individually fine-tuned for best performances.

It is difficult to capture the real-time online measurement data for biochemical oxygen demand (BOD) in wastewater treatment processes. An optimized extreme learning machine (ELM) based on an improved cuckoo search algorithm (ICS) is proposed in this paper for the design of soft BOD measurement model. In ICS-ELM, the input weights matrices of the extreme learning machine (ELM) and the threshold of the hidden layer are encoded as the cuckoo's nest locations. The best input weights matrices and threshold are obtained by using the strong global search ability of improved cuckoo search (ICS) algorithm. The optimal results can be used to improve the precision of forecasting based on less number of neurons of the hidden layer in ELM. Simulation results show that the soft sensor model has good real-time performance, high prediction accuracy and stronger generalization performance for BOD measurement of the effluent quality compared to other modeling methods such as back propagation (BP) network in most cases.

Protein immobilization for the functionalization of particles is used in various applications, including biosensors, lateral-flow immunoassays (LFIA), bead-based assays, and others. Common methods for the quantification of bound protein are measuring protein in the supernatant before and after coating and calculating the difference. This popular approach has the potential for a significant overestimation of the amount of immobilized protein since layers not directly bound to the surface (soft protein corona) are usually lost during washing and handling. Only the layer directly bound to the surface (hard corona) can be used in subsequent assays. A simplified amino acid analysis method based on acidic hydrolysis and RP-HPLC-FLD of tyrosine and phenylalanine (aromatic amino acid analysis, AAAA) is proposed to directly quantify protein bound to the surface of gold nano- and latex microparticles. The results are compared with indirect methods such as colorimetric protein assays, such as Bradford, bicinchoninic acid (BCA), as well as AAAA of the supernatant. For both particle types, these indirect quantification techniques show a protein overestimation of up to 1700% compared to the direct AAAA measurements. In addition, protein coating on latex particles was performed both passively through adsorption and covalently through EDC/sulfo-NHS chemistry. Our results showed no difference between the immobilization methodologies. This finding suggests that usual protein determination methods are no unambiguous proof of a covalent conjugation on particles or beads.

Over the last decade, the field of Human Attribute Recognition (HAR) has dramatically changed, mainly due to the improvements brought by deep learning solutions. This survey reviews the progress obtained in HAR, considering the transition from the traditional hand-crafted to deep-learning approaches. The most relevant works on the field are analyzed concerning the advances proposed to address the HAR's typical challenges. Furthermore, we outline the applications and typical evaluation metrics used in the HAR context. Finally, we provide a comprehensive review of the publicly available datasets for the development and evaluation of novel HAR approaches.

High fructose and sugar-sweetened soft drink (SSSD) intakes are associated with elevated blood uric acid concentrations and increased risk of gout and cardiovascular disease. Fruits are naturally high in fructose but their effect on cardiometabolic risk is unknown. We examined the effect on serum uric acid and cardiometabolic risk factors of consuming fructose from either fruit or SSSD in overweight adults. 48 healthy, overweight (BMI≥ 28 kg/m²) men (n=21) and women (n=20) were randomised to either a fruit (n = 19) or SSSSD (n = 22) intervention for 4 weeks. The fruit group received 6 items of fresh and dried fruit per day and the SSSD group received 955ml of SSSD per day with treatments matched for energy and fructose content. Serum uric acid concentrations were significantly reduced in men in the fruit group compared to the SSSD group (difference 57.2 μmol/L [95% CI: 16.4, 98.0], p= 0.008) but there was no difference amongst women (1.3 μmol/L [95%CI: -9.5, 6.9], p= 0.295). There differences in weight change or other cardiometabolic risk factors. These findings suggest no need to restrict fruit intake in individuals with elevated serum uric acid concentrations, such as those with gout.

The necessity to reduce the effect of the greenhouse phenomenon imposed the turn of the food packaging technology to the use of biobased raw materials decreasing the carbon dioxide fingerprint. In this direction alginates derived from brown algae species are of the most promising biobased biopolymers, used for development of edible active coatings, capable to protect food from oxidation/bacterial spoilage. In this study sodium alginate, which was plasticized with glycerol and mixed with a biobased thymol/natural halloysite nanohybrid, was used to develop novel edible active coatings. Active nanocomposite coatings developed by mixing of pure halloysite with sodium alginate/glycerol matrix were produced for comparison purposes. X-Ray and Fourier Transform Infrared Spectroscopy indicated higher compatibility of thymol/halloysite nanohybrid with sodium alginate/glycerol matrix compared to the relevant of pure halloysite. This increased compatibility led to higher tensile properties, water/oxygen barrier properties, and total antioxidant activity. All coating samples were applied as edible active coatings for “tsalafouti” spreadable soft cheese, exhibited a reduction of mesophilic microbial population of more than one log10(cfu/g) unit comparing with uncoated cheese. Moreover, the reduction of mesophilic microbial population was increased by increasing halloysite and thymol content which indicates the sodium alginate/glycerol/thymol/halloysite as promising edible active coatings for “tsalafouti”.

Machine learning (ML) methods has recently contributed very well in the advancement of the prediction models used for energy consumption. Such models highly improve the accuracy, robustness, and precision and the generalization ability of the conventional time series forecasting tools. This article reviews the state of the art of machine learning models used in the general application of energy consumption. Through a novel search and taxonomy the most relevant literature in the field are classified according to the ML modeling technique, energy type, perdition type, and the application area. A comprehensive review of the literature identifies the major ML methods, their application and a discussion on the evaluation of their effectiveness in energy consumption prediction. This paper further makes a conclusion on the trend and the effectiveness of the ML models. As the result, this research reports an outstanding rise in the accuracy and an ever increasing performance of the prediction technologies using the novel hybrid and ensemble prediction models.

In this paper, several two-dimensional clustering scenarios are given. In those scenarios, soft partitioning clustering algorithms (Fuzzy C-means (FCM) and Possibilistic c-means (PCM)) are applied. Afterward, VAT is used to investigate the clustering tendency visually, and then in order of checking cluster validation, three types of indices (e.g., PC, DI, and DBI) were used. After observing the clustering algorithms, it was evident that each of them has its limitations; however, PCM is more robust to noise than FCM as in case of FCM a noise point has to be considered as a member of any of the cluster.

We report a small footprint cost-effective isothermal rapid DNA amplification system, with integrated microfluidics for automated sample analysis and detection of SARS-CoV-2 in human and environmental samples. Our system measures low-level fluorescent signal in real-time during amplification, while maintaining the desired assay temperature, on a low power, portable system footprint. A unique soft microfluidic chip design was implemented to mitigate thermocapillary effects and facilitate optical alignment for automated image capture and signal analysis. The system-on-board prototype coupled with the LAMP primers designed by BioCoS, is sensitive enough to detect viral loads of SARS-CoV-2 in a broad concentration range corresponding to a threshold cycle range of 16 to 39. Clinical specimens were tested at Kingston Health Sciences using a clinically validated PCR assay and variants were determined using whole genome sequencing.

The Golgi apparatus (GA) dysfunctions in Parkinson’s Disease (PD), neurodevelopmental disorders (NDDs), cancer, and organelle structural biology (OSB) can provide insights into therapeutic targets, gene therapy, and drug design. Primary defects and fragmentation within the GA are implicated in a wide range of neurodegenerative diseases. GA defects typically result in mislocation of proteins, accumulation of undegraded proteins, and impaired glycosylation of proteins. Inhibition of vesicular trafficking by α-synuclein (aSyn) may affect the dopamine-producing neurons and neuromodulators. GA regulates apoptosis during pathological mechanisms of neurological diseases and could provide new avenues in treatments through translation research. PD patients bearing the hereditary E46K disease mutation manifest the clinical picture of parkinsonism. How do we provide high resolution nanoimages of the GA during disease to capture dysfunction? Could we visualize the aSyn traffic jam between vesicles in the organelles ER and GA? OSB is emerging as a field as more technology advances and is more accessible. Structural studies of the GA will advance the field of neurological disease forward with an in depth understanding of dysfunction, fragmentation, and defects. Discoveries of the GA in PD, NDDs, and cancer would break new ground and provide translational medicine data of these diseases. Future research could be visualizing high angle annular dark field-STEM (HAADF-STEM) tomograms, cryogenic electron tomography (cryo-ET), multiplex correlative light and electron microscopy (cryo-CLEM), nanobody-assisted tissue immunostaining for volumetric EM (NATIVE) and using soft X-ray tomography (SXT) and computational reconstruction of the GA.

Refineries execute a series of interlinked processes, where the product of one unit serves as the input to another process. Potential failures within these processes affect the quality of the end products, operational efficiency, and revenue of the entire refinery. In this context, implementation of a real-time cognitive module, referring to predictive machine learning models, enables to provide equipment state monitoring services and to generate decision-making for equipment operations. In this paper, we propose two machine learning models: 1) to forecast the amount of pentane (C5) content in the final product mixture; 2) to identify if C5 content exceeds the specification thresholds for the final product quality. We validate our approach by using a use case from a real-world refinery. In addition, we develop a visualization to assess which features are considered most important during feature selection, and later by the machine learning models. Finally, we provide insights on the sensor values in the dataset, which help to identify the operational conditions for using such machine learning models.

Building energy consumption plays an essential role in urban sustainability. The prediction of the energy demand is also of particular importance for developing smart cities and urban planning. Machine learning has recently contributed to the advancement of methods and technologies to predict demand and consumption for building energy systems. This paper presents a state of the art of machine learning models and evaluates the performance of these models. Through a systematic review and a comprehensive taxonomy, the advances of machine learning are carefully investigated and promising models are introduced.

The combination of artificial intelligence algorithms and numerical methods has recently become popular in the prediction of macroscopic and microscopic hydrodynamics parameters of bubble column reactors. The multi inputs and outputs machine learning can cover small phase interactions or large fluid behavior in industrial domains. This numerical combination can develop the smart multiphase bubble column reactor with the ability of low-cost computational time. It can also decrease case studies for the optimization process when big data is appropriately used during learning. There are still many model parameters that need to be optimized for a very accurate artificial algorithm, including data processing and initialization, the combination of inputs and outputs, number of inputs and model tuning parameters. For this study, we aim to train four inputs big data during learning process by an adaptive neuro-fuzzy inference system or adaptive-network-based fuzzy inference system (ANFIS) method, and we consider the superficial gas velocity as one of the input variables, while for the first time, one of the computational fluid dynamics (CFD) outputs named gas velocity is used as an output of the artificial algorithm. The results show that the increasing number of input variables improves the intelligence of the ANFIS method up to , and the number of rules during learning process has a significant effect on the accuracy of this type of modeling. The results also show that propper selection of model parameters results in more accuracy in prediction of the flow characteristics in the column structure.

Electrically conductive adhesives (ECA’s) are used widely to replace or reinforce lead soldering or conductive metal components in electronic packaging applications such as die attachment, solderless interconnections, component repair, display interconnections, and heat dissipation. Their conductive behavior as well as the associated behaviors such as heat conduction and mechanical behavior (strength, rigidity, deformation and viscoelastic behavior, which may be affected by moisture ingression) are affected by adhesive film thickness, volume fraction, size and shape of the conductive filler, as well as uncured base adhesive viscosity, substrate and filler surface treatment and the applied pressure (during bonding and during conduction). The adhesive resistivity decreases precipitously above a characteristic filler volume fraction called the percolation threshold. In general, micron-sized metal fillers mixed in an adhesive (often an epoxy) resulting with different film thicknesses exhibit thickness thresholds for transition from three-dimensional conductivity to two-dimensional conductivity with considerable increases in thickness-direction (z-axis) resistivity when the film thicknesses are smaller than these threshold values. Recently, the use of conductive nanoparticles allowed decreases in percolation threshold levels as well as increases in mechanical strength and durability of ECA’s. Most ECA’s are supplied in liquid or paste form in varying viscosities and therefore, the method of their application also affects their performance. This work intends to provide an understanding of these effects on conduction behavior in (usually high-priced) equipment in which they are used.

Appropriate estimation of soil settlement is of significant importance since it directly influences the performance of building and infrastructures that are built on soil. In particular, the settlement of fine-grained soils is critical because of low permeability and continuous settlement with time. Coefficient of consolidation (Cc) is a key parameter to estimate settlement of fine-grained soil layers. However, estimation of this parameter is time consuming, needs skilled technicians, and specific equipment. In this study, Cc was estimated using several soil parameters such as liquid limit (LL), plastic limit (PL), and initial void ratio (e0). Estimating such parameters in laboratory is straight forward and needs substantially less time and cost compared to conventional tests to estimate Cc such as Oedometer test. This study presents a novel prediction model for Cc of fine-grained soils using gene-expression programming (GEP). GEP is a biologically inspired technique capable of offering closed-form solution for the optimal solution. A database consisted of 108 different data points was used to develop the model. A closed-form equation solution was derived to estimate Cc based on LL, PL, and e0. The performance of developed GEP-based model was evaluated through coefficient of determination (R2), root mean squared error (RMSE), and mean average error (MAE). High R2 and low error values indicated the descent performance of the model. Furthermore, the model was evaluated using the additional performance measures and met all the suggested criteria. Furthermore, the model had a better performance in terms of R2, RMSE, and MAE compared to most of existing models. It is expected that the developed model will decrease the time and cost associate with determining Cc of fine-grained soils.

Soft-Core architecture for Analogue to Digital Converter (ADC) sampling is useful for mixed signal applications. Soft-core architecture for cutting edge odd or even ADC sampling with interface to block RAM memory has not been found. Soft-core architecture as a concept has become popular due to the advantage of customization for different applications as compared to general-core architecture suited for single application. The latest generation of piece wise sampling is odd sampling and was introduced in the second decade of the 20th century. Odd and even order sampling techniques are analogue in nature driven by a tuned (tuned for odd or even) mixer. This paper proposes a third-generation piece wise sampling with soft-core architecture that enables an option to select both odd and even while interfacing to memory mapping. The proposed odd/even has superior SNR performance of 6 dB as compared to existing architecture such as Mod-∆ which recorded worst performance of 18 dB. Advances in soft-core technology have allowed a niche odd/even switching field to be identified and studied, the study has also been extended to include memory architecture.

Appropriate estimation of soil settlement is of significant importance since it directly influences the performance of building and infrastructures that are built on soil. In particular, the settlement of fine-grained soils is critical because of low permeability and continuous settlement with time. Coefficient of consolidation (C_c) is a key parameter to estimate settlement of fine-grained soil layers. However, estimation of this parameter is time consuming, needs skilled technicians, and specific equipment. In this study, C_c was estimated using several soil parameters such as liquid limit (LL), plastic limit (PL), and initial void ratio (e₀). Estimating such parameters in laboratory is straight forward and needs substantially less time and cost compared to conventional tests to estimate C_c such as oedometer test. This study presents a novel prediction model for C_c of fine-grained soils using gene-expression programming (GEP). GEP is a biologically inspired technique capable of offering closed-form solution for the optimal solution. A database consisted of 108 different data points was used to develop the model. A closed-form equation solution was derived to estimate C_c based on LL, PL, and e₀. The performance of developed GEP-based model was evaluated through coefficient of determination (R²), root mean squared error (RMSE), and mean average error (MAE). High R² and low error values indicated the descent performance of the model. Furthermore, the model was evaluated using the additional performance measures and met all the suggested criteria. Furthermore, the model had a better performance in terms of R², RMSE, and MAE compared to most of existing models. It is expected that the developed model will decrease the time and cost associate with determining C_c of fine-grained soils.Keywords: evolutionary model, gene-expression programming (GEP), prediction, soil compression index, estimation, soil engineering, soil informatics, civil engineering, machine learning, data science, big data, soft computing, deep learning, forecasting, subject classification codes, construction informatics, computational intelligence (CI), artificial intelligence (AI), estimation