In metal continuous casting process is important to estimate the temperature evolution of casted section along machine from meniscus (point in which liquid metal is poured) to cutting machine where product is cut at commercial length. Particularly in the case of large sections, a convenient approximated model to achieve this goal with a feasible computational effort, is the so called travelling slice: the transversal section of casted product is subjected to different thermal boundary conditions (e.g. thermal flux, radiation, convection) that are found during the movement at constant speed from meniscus to the end of machine. In the case of an axisymmetric section, a comparison with the exact solution can be easily achieved. The article will show pros and cons of both, namely the far lower computational cost of travelling slice model without losing precision. Results confirm the validity of the travelling slice approach also at low casting speed and huge dimensions.

The requirement for developing tools capable of detecting and monitoring heavy metals (HMs) has recently taken on more significance due to worries about their toxic effect on human health and aquatic habitats. In this study, a simple electrochemical sensing carbon paste electrode (CPE) based on composite of Zinc/Iron layered double hydroxide (LDH) and polyaniline (PANI) was developed for the determination of lead ions in aquatic solutions. For this purpose, Zn-Fe LDH/PANI was prepared and characterized by Fourier transform infrared (FTIR), X ray diffraction (XRD), and scanning electron microscopy (SEM). Modified carbon electrode based Zn-Fe LDH/PANI was electrochemically characterized compared with unmodified electrode in FCN as a redox probe using cyclic voltammetry (CV). Thus, Zn-Fe LDH/PANI was utilized as sensing material for the electrochemical determination of lead ions using differential pulse voltammetry (DPV). Zn-Fe LDH/PANI/CPE show limits of detection (LOD) and quantification (LOQ) of 167.8 nM and 559.4 nM, respectively. Zn/Mg/Fe LDH was prepared using co-precipitation method and characterized by XRD, FTIR, SEM and BET, used for removal of Pb+2 ions. Removal process was investigated at different conditions as pH, metal ion concentrations, starting adsorbent dose at first and contact time. Zn/Mg/Fe LDH was evaluated as an effective adsorbent material for lead ions elimination in aquatic solutions, with capacity of adsorption 700 mg/g. The elimination of lead ions on Zn/Mg/Fe LDH fitted the pseudo first-order kinetics model and the isotherm was matched with Langmuir model. Studies revealed that the ideal removal conditions were pH = 5.0, an adsorbent mass of 0.05 g, and 20 ml of 50 ppm metal ion concentration at 60 min. The Zn-Fe LDH/PANI composite also showed potential anti-cancer properties against lung cancer cells (A549) while maintaining safety for normal lung fibroblast cells (WI-38). Collectively, advancements in electrochemical sensors offer promising solutions for lead ion detection, with wide-reaching applications in wastewater treatment and cytotoxicity assessment. These innovations have the potential to enhance environmental monitoring and public health safety.

In vitro glucose uptake in yeast cell facilitated by Abelmoschus esculentus L. (okra seed) for management of type 2 diabetes was studied. Plant material was collected, identified, processed, and stored for further use. 80% methanol was employed for extraction and sonicated to release antidiabetic-bioactive component in solution and was filtered, concentrated, freeze-dried, and fractionated using standard techniques. Glucose uptake at an initial concentration of 5mM/L and 10mM/L by the crude extract was consistent to that of the known standard drug while at 25mM/L glucose concentration was equivalent with the crude extract. Also, at 0.625 mg/mL the linear equations, and R2 demonstrations that the crude extract was higher in dose predictability than the standard drug as presented by the equation; y = 35.754x - 57.822, and R² = 0.9502 (95%). The extract-fractions were employed to evaluate the ability of yeast cell line culture to take up glucose from the system through DPPH, FRAP, lipid peroxidation and anti-diabetes effect of extract-fraction assays. Extract-fractions were found to poses antioxidant activity high enough to inhibit stress-related diseases. The extract fractions were active as drug candidates both at low and high concentrations and were better compared with the standard drug and standard antioxidant was comparable. The high bioactive extract fractions require encapsulation with a nanoparticle as a drug candidate for type 2 diabetes patients. And an animal trial of the drug candidate may be necessary to monitor the in vivo performances of the extract fractions and subsequent human volunteered trial.

Iron is an essential micronutrient for Citrus, playing an important role in photosynthesis and yield. The aim of this paper is to evaluate the tolerance to Fe deficiency of five Citrus rootstocks: sour orange (S), Carrizo citrange (C), Citrus macrophylla (M), Troyer citrange (T) and Volkamer lemon (V). Plants were grown for 5 weeks in nutrient solution that contained the following Fe concentrations (in µM): 0, 5, 10, 15 and 20. At the end of the experiment, biomass (dry weight), leaf area, total leaf chlorophyll (CHL) and the activity of root chelate activity (FCR) were registered. Additionally, the mineral composition of roots (R) and shoots (S) was evaluated. Principal Component Analysis was used to study the relationships between all parameters and, subsequently, the relations between rootstocks. In the first component, N-S, P-S, Ca-S, Cu-S, Zn-S, Mn-S and Zn-R and Mn-R concentrations were related to leaf CHL and FCR. Increases in leaf CHL, Mg-R, DW (shoots and roots) were inversely related to Cu-R, which was shown in the second component. The values obtained were consistent for V10, C15, and C20, but in contrast for S0 and S5. Overall, the Fe/Cu ratio was significantly related to CHL, which may be used to assist rootstock performance.

Al has very good corrosion resistance and corrosion properties. The corrosion resistance of Al cast alloys is different because these alloys contain a lot of elements. Especially in secondary alloys which contain more impurity elements from which Fe is the most common. This study deals with secondary AlSi7Mg0.3 cast alloys which contain more Fe and are affected by a chloride corrosion environment. This environment was selected based on the application of castings in the automo-tive industry. The main object was to research the effect of such an environment on basic me-chanical properties and fatigue properties. The results show that a higher Fe content does not lead to a significant reduction in the properties of the casting and the chloride environment is not so harmful. Therefore, can be stated that the investigated secondary sand-cast experimental materials can replace the primary alloys without losing the required corrosion and mechanical properties.

Ti-aluminosilicate gels were used as supports for immobilization of Fe, Co and Ni oxides (5%) by impregnation, and synthesis of efficient photocatalysts in degradation of β-lactam antibiotic from water. Titanium oxide (1 and 2%) was incorporated into zeolite network by modifying the gel during the zeolitation process. The formation of the zeolite Y structure and its microporous structure were evidenced by X-ray diffraction and N2 physisorption. The structure, composition, reduction and optical properties were studied by X-ray difraction, H2-TPR, XPS, Raman, photoluminiscence and UV-Vis spectroscopy. The obtained results indicated a zeolite Y structure for all photocatalysts with tetra-coordinate Ti4+ sites. The immobilized metals from group VIII are both in the form of metal oxides such as Fe2O3, Fe3O4, CoO, Co3O4 , NiO and also in the me-tallic state (Fe0, Co0, and Ni0). A red shift of the absorption edge was observed in UV-Vis spectra of photocatalysts upon addition of Fe, Co or Ni species. The photocatalytic performances were evaluated in degradation of cefuroxime from water under visible light irradiation. The best results were obtained for iron immobilized photocatalysts. Scavenger experiments explained the photocatalytic results and their mechanisms. A different contribution of the active species to the photocatalytic reactions was evidenced.

The process of anaerobic digestion used for methane production can be enhanced by incorporating stimulating materials. The effects of these materials are dependent on various factors including the processed substrate, process conditions, and the type and amount of the stimulating material used. As part of the study, three different stimulating materials - iron powder, lime, and milled porous ceramic - were added to the 30-day anaerobic digestion of the brewer's spent grain to improve its performance. Different doses ranging from 0.2 to 2.3 gTS×L-1 were tested, and methane production kinetics were determined using the first-order model. The results showed that the methane yield ranged from 281.4±8.0 to 326.1±9.3 ml×gVS-1, while substrate biodegradation ranged from 56.0±1.6 to 68.1±0.7%. The addition of lime reduced methane yield at almost all doses by -6.7% to -3.3%, while the addition of iron powder increased methane yield from 0.8% to 9.8%. The addition of ceramic powder resulted in a methane yield change ranging from -2.6% to 4.6%. These findings suggest that the use of stimulating materials should be approached with caution, as even slight changes in the amount used can impact methane production.

Obesity and physical activity have opposing effects on cardiorespiratory fitness. This study aimed to investigate the impact of obesity measured by various anthropometric indicators and physical activity level on oxygen uptake and fat oxidation during moderate-intensity aerobic exercise in adults. Forty-eight individuals were recruited. Various anthropometric indicators (i.e., body mass index (BMI), waist circumference (WC), waist-to-hip ratio (WHR), and waist-to-height ratio (WHtR)) were measured. Physical activity was assessed using the International Physical Activity Questionnaire (a short version). Total oxygen uptake (VO2tot) and fat oxidation were recorded during 30-minute aerobic exercise at moderate intensity. There were no differences in oxygen uptake and fat oxidation between obese and non-obese groups. Based on obesity and physical activity, VO2tot was significantly different among groups classified by WHR. Inactive obesity had significantly lower VO2tot 28.1% compared to active obesity and 29.2 % compared to active non-obesity. The inactive obesity had a 3.8%, 27.4%, and 4.3% lower fat oxidation than the active non-obesity, as classified by WC, WHR, and WHtR, respectively. However, the differences were not statistically significant. We conclude that active obesity, as measured by WHR, exhibited higher oxygen uptake compared to inactive obesity. Moreover, inactive obesity showed poorer oxygen uptake than active non-obesity.

: The article examines the regularities of structure formation of ultrafine fibers based on poly-3-hydroxybutyrat under the influence of technological (electrical conductivity, viscosity), molecular (molecular weight), and external factors (low-molecular and nanodispersed substances of different chemical nature). Systems with polar substances are characterized by the presence of intermolecular interactions and the formation of a more perfect crystalline fiber structure. Changes in technological and molecular characteristics affect the fiber formation process, resulting in alterations in the morphology of the non-woven fabric, fiber geometry, and supramolecular fiber structure. Polymer molecular weight, electrical conductivity, and solution viscosity influence fiber formation and fiber diameter. The fiber structure is heterogeneous, consisting of both crystalline and non-equilibrium amorphous phases. This is significant in the development of matrix-fibrillar systems for drug delivery, bioactive substances, antiseptics, tissue engineering constructs, tissue engineering scaffolds, artificial biodegradable implants, sorbents, and other applications.

Iron (Fe) deficiency specifically is the most common nutritional disorder due to insufficient absorbable Fe. Biofortification is a process of enriching the nutrient content of staple crops and is considered as a sustainable and cost-effective strategy to address micronutrient deficiency problems especially in the less developed countries. Chickpea (Cicer arietinum L.) is a staple food in many developing countries worldwide and is an excellent source of micronutrients. Biofortification of chickpea is a possible solution to address Fe deficiency problem. Chickpea biofortification experiment was conducted under field conditions to evaluate the effects of different doses of Fe fertilizer (0 kg ha-1,10 kg ha-1 and 30 kg ha-1 of Fe-EDDHA) on Fe content in seeds of 18 chickpea cultivars. The experiment was designed as a factorial combination of 18 chickpea cultivars and 3 different doses in a randomized complete block design with 4 replications at two locations in Saskatchewan in 2015 and 2016. Fe concentration in seeds across 18 different chickpea cultivars increased with Fe fertilization. Fe concentration in X05TH20-2 and CDC Frontier cultivars increased from 57 ppm to 59 ppm and 56 ppm to 58 ppm, respectively, after adding Fe fertilizer in both location in 2015 and 2016.

: Broad-spectrum antifungal drug deployed for topical therapy, specific for onychomycosis, Itraconazole was used as the active pharmaceutical ingredient in a nail lacquer formulation1. The objective of the study was to optimize an antifungal nail lacquer, which when applied topically onto the dorsal surface of the nail plate would facilitate the transungual penetration of the drug. Itraconazole hydrochloride was synthesized to aid the formulation of the lacquers. The optimization involved comparing four different formulations of 1%w/w Itraconazole nail lacquers containing combinations of penetration enhancers (Urea, Salicylic acid, and Papain) based on their ability to facilitate diffusion of the drug through the nail plate over five days. The drug uptake was quantified by extracting the drug from the nail clippings and analyzing it. The tests conducted to account for the quality of the optimized formulation were drug content, spreadability, check for precipitation, and accelerated stability. The results demonstrated that the optimized 1%w/w Itraconazole nail lacquer contained 5%w/w Salicylic acid, 5 %w/w Papain, and 2.8% w/w Urea. The drug uptake from nail clippings was higher than the MIC90 for T. Rubrum strain, and the quality of the optimized lacquer was not compromised throughout three weeks2. The hypothesis stated that the inclusion of Salicylic acid, Papain, and Urea in an Itraconazole (1%w/w) nail lacquer would have the highest transungual penetration on application to the nail plate. In conclusion, the hypothesis was accepted, and the optimized lacquer passed the drug uptake evaluation and all quality control tests.

Phosphorus (P) deficiency is a major constraint limiting sustainable rice cultivation in sub-Saharan Africa—partly due to the deeply weathered soils that have low pH and contain high P-fixing Fe and Al oxides. Soil texture also affects P availability and use efficiency. In this study, we evaluated the combined effect of soil texture (sand, clay loam, and clay) and P treatments (P-dipping and two other P fertilizer levels) on growth of NERICA 4 rice in the initial growth stages. In a factorial experiment, we measured the interaction effects of soil texture and P treatments on shoot parameters and root morphology. Both treatments had significant interaction effects on all measured parameters, except shoot biomass, and affected the photosynthetic rate, with the highest mean values obtained under clay loam soil texture and P-dipping treatment, respectively. The treatments also affected rice root morphology. In a striking contrast, whereas mean root length under clay was significantly higher than that under clay loam texture, mean shoot P uptake under clay loam soil was significantly higher than that under clay soil texture. The interactive effect of soil texture and P-dipping influenced NERICA 4 shoot and root physiological and morphological characteristics under clay loam soil texture.

In this paper, Fe-Cr-C-N-Al-Y wear-resistant surfacing alloy was prepared by open arc surfacing with self-shielded flux-cored wire. The wear properties of the surfacing alloy were analyzed by MLS-23 rubber wheel wet sand wear tester. The phase composition and microstructure of the surfacing alloy were analyzed by XRD, SEM, EBSD and TEM, and the strengthening mechanism and wear mechanism of the alloy were discussed. The results show that the microstructure of Fe-Cr-C-N-Al-Y surfacing alloy is composed of M + γ-Fe + M7C3 + AlN. When the content of nano-Y2O3 is 0.456wt. %, the formability of the surfacing alloy is the best and the wetting angle is the smallest, which is 50.8°, AlN and M7C3 precipitate the most, and the microstructure grain is the smallest. At this time, the hardness value of the surfacing alloy is up to 62.3 HRC, which is 11.8 % higher than that of the unmodified surfacing alloy. The minimum wear weight loss is 0.125 g, and the wear resistance is increased by 41.86 %. The wear mechanism of surfacing alloy is mainly plastic deformation mechanism, and the material removal process is micro cutting and furrow wear.

This rapid review aims to present a comprehensive overview of barriers and facilitators or factors, and, effective interventions that promote immunisation uptake by older people in the Asia-Pacific region. Rapid review methodology was applied using two databases (PubMed, Embase). Articles were included if studies were conduced in Australia, Singapore, Indonesia and the Philippines, included human population ≥50 years old, used original data, adopted quantitative, qualitative, and mixed-method designs, and published from 2016 to August 2022. The study selection yielded 1424 articles. A total 23 papers met the inclusion criteria, of which 19 reported on barriers and facilitators, while, 4 articles reported on effective interventions to promote vaccination uptake. Among the 19 studies that identified barriers and facilitators to vaccination uptake, the more common factors were social influences (n=8/19), perceived benefits of vaccine (n=7/19), and perceived vaccine safety (n=6/19). Strategies that focussed on supporting clinicians were found to be effective in leading them to recommend vaccinations among older adults such as creating awareness on the low baseline vaccination rates among older adults, provision of structured health assessment, and nurse reminders. More studies are needed ascertain the factors, and effective interventions influencing vaccine uptake among older people in the Asia-Pacific region.

Fe- and Al-rich metapelite from the Transangarian segment of the Yenisey Ridge (East Siberia, Russia) is a potential new source of high-alumina refractories. The rocks have relatively high average contents of Al2O3 (20 wt.%) and Fe2O3 (7.91 wt%), moderate K2O (3.44 wt%), and low CaO (0.74 wt%). Their dominant mineral assemblages are andalusite + muscovite + margarite + chlorite + biotite + quartz or staurolite + kyanite or/and andalusite + chlorite + muscovite + biotite + quartz with ±garnet and ±plagioclase. Al2SiO5 polymorphs occur as up to 1.5 cm andalusite porphyroblasts and partial or complete pseudomorphs after andalusite (kyanite and staurolite). Accessories include abundant Fe-Ti oxides and sporadic REE-, Y-, Ca-phosphates; sulfides are negligible. The composition of Al2SiO5 concentrates obtained in laboratory by heavy-media and magnetic separation from ≥0.06 mm fractions meet all requirements for raw material of this type: >56 wt% Al2O3, <42 wt% SiO2, <1 wt% Fe2O3, <1.2 wt% TiO2, and <0.2 wt% (CaO+MgO). The andalusite, kyanite, and mixed ores yield 0.7-4.1 wt%, 0.7-2.2 wt%, and 1.9-6.0 wt% of concentrate, respectively. The best-quality ores rich in Al2SiO5 polymorphs reside in zones of contact and/or dynamic metamorphism superimposed over regional metamorphism of Al-rich rocks.

We recently developed a novel hyperspectral excitation-resolved near-infrared fluorescence imaging system (HER-NIRF) based on a continuous-wave wavelength-swept laser. In this study, this technique is applied for measuring the distribution of the therapeutic agent dimethyl sulfoxide (DMSO) by utilizing solvatochromic shift in the spectral profile of albumin-bound Indocyanine green (ICG). Using wide-field imaging in turbid media, complex dynamics of albumin-bound ICG is measured in mixtures of dimethyl sulfoxide (DMSO) and water. Phantom experiments are conducted to evaluate the performance of the HER-NIRF system. The results show that the distribution of DMSO can be visualized in the wide-field reflection geometry. One of the main purposes of the DMSO is to act as a carrier for other drugs, enhancing their effects by facilitating skin penetration. Understanding solubility and permeability of drugs in vivo is very important in drug discovery and development. Hence, this HER-NIRF technique has a great potential to advance the utilization of the therapeutic agent DMSO by mapping its distribution via solvatochromic shift of ICG. By customizing the operational wavelength range, this system can be applied to any other fluorophores in the near infrared region and utilized for a wide variety of drug delivery studies.

The concrete sector is known for its significant contribution to the CO2 emissions. There are two main contributing factors for this situation: the large amount of concrete consumed per year on the planet and the high CO2 released from Portland cement manufacture, the key binding agent in concrete. To face the consequent sustainability issues, diverse strategies have been explored on the carbon capture and storage potential of cementitious materials. This paper addresses the potential of storing CO2 in concrete during the curing stage, applied to the precast Portuguese industry. To this purpose, it was assumed that CO2 will become a waste that will require an outlet in the future, considering that carbon capture will become mandatory in many industries. This work concluded that the net benefit in terms of carbon retention is positive for the process of storing carbon in concrete during the curing stage. More specifically, it was demonstrated that the additional emissions from the introduction of this new operation are only 10% of the stored amount, returning a storage potential of 76 000 tonnes of CO2 yearly. Moreover, the overall net reduction in the concrete life cycle averages 9.4% and 8.8% for precast elements and only non-structural elements, respectively. When a low cement dosage strategy is coupled with carbonation curing technology, the overall carbon net reduction is estimated to be 45%.

Diesel contamination of farming soils is of great concern because hydrocarbons are toxic to all forms of life and can potentially enter the food web through crops or plants used for remediation. Data on plant ability to uptake, translocate and accumulate diesel-derived compounds are controversial not only due to the probable diverse attitude of plant species but also because of the lack of a reliable method to distinguish petrogenic from biogenic compounds in plant tissues. The purpose of this study was to set up a GC-MS-based protocol enabling the determination of diesel-derived hydrocarbons in plants grown in contaminated soil for assessing human and ecological risks, predicting phytoremediation effectiveness and biomass disposal. To this aim two plant species Vicia sativa L. and Secale cereale L., belonging to two diverse vascular plant families, were used as plant models. They were grown in soil spiked with increasing concentrations of diesel fuel and the produced biomass was used to set up the hydrocarbon extraction and GC-MSD analysis. The developed protocol was also applied to the analysis of Typha latifolia L. plants, belonging to a different botanical family and grown in a long-time and highly contaminated natural soil. Results showed the possibility of distinguishing diesel-derived compounds from biogenic hydrocarbons in most terrestrial vascular plants, just considering the total diesel compounds in the n-alkanes carbon range C10-C26, where the interference of biogenic compounds is negligible. Diesel hydrocarbons quantification in plant tissues was strongly correlated (0.92<r2<0.99) to the concentration of diesel in spiked soils, suggesting a general ability of the considered plant species to adsorb and translocate relative low amounts of diesel hydrocarbons and the reliability of the developed protocol.

The effects of rare earth Y content on the microstructure and high-temperature oxidation properties of 47Fe-36Ni-15Cr-1.5Mn alloy at 1000°C were investigated. The results show that 47Fe-36Ni-15Cr-1.5Mn alloy oxidizes at 1000°C under laboratory atmospheric pressure to form an oxide film layer dominated by Cr2O3 and (Fe, Ni, Mn) Cr2O4 spinel, and the oxidation curve of the alloy follows the parabolic law. After the addition of rare earth Y, rare earth phases precipitated along the grain boundaries in the alloy, and the more Y content, the more precipitated phases in the grain boundaries. The alloy with added rare earths was oxidized at a high temperature of 1000 °C for 2160 min, the oxidation law still followed the parabolic law, while the rare earth phase at the grain boundary reacted with the oxygen atoms infiltrated from the outside to generate a rare earth Y-rich oxide residing at the boundary between the grain boundary and the precipitated phase of the alloy. Add 0.5 wt.% rare earth Y 47Fe-36Ni-15Cr-1.5Mn-0.5Y alloy 1000 ° C high temperature oxidation of the formation of spinel oxide crystalline particles, dense and complete oxide film layer, the surface of the addition of a small amount of (0.5 wt.%) rare earth Y after the refinement of the oxide particles, and in the alloy grain boundaries in the form of oxides reside in the alloy to inhibit the cations in the matrix and the oxygen negative ions. and oxygen-negative ions in the alloy matrix, improving the antioxidant performance of the alloy. With the further increase of rare earth Y, during the oxidation of the alloy at high temperature, the precipitation phase at the grain boundary promotes the inward diffusion of oxygen, resulting in the deterioration of the antioxidant property of the alloy.

Key elements of Blue-Green Infrastructure are vegetation and stormwater storage. A combination of a bioretention cell with an underlying trench (BC-T) serving as a tree pit is often used in dense urban environments. An adequate ratio of drained area to bioretention cell area is a crucial design parameter. The ratio is derived from the hydrological balance; however, input data are often difficult to obtain or uncertain. The goal is to study the sensitivity of such data (tree water uptake and water holding capacities of soil filter and trench substrate) in the BC-T design. Sensitivity analysis is performed for the setup of a BC-T used in Prague, Czech Republic. A 10-year rainfall series (1 hour resolution) is used as an input. Data that are subject to the sensitivity analysis are changed for different trench exfiltration rates, and the effect on the size of the drained area is studied. At low trench exfiltration rates (1.8 mm.h-1), both the water holding capacity of the trench substrate and potential tree water uptake have a significant influence (more than a 20% change in the size of the drained area) and cannot be neglected. At good exfiltration rates (more than 18 mm.h-1) or when the trench is equipped with an underdrain, all studied parameters can be neglected. However, it is recommended to reduce the size of the drained area by 10-20%.

Objective: Polymyalgia rheumatica (PMR) and giant cell arteritis (GCA) are often overlapping conditions. We aimed to determine whether 18F-fluorodeoxyglucose (FDG) positron emission tomography-computed tomography (PET-CT) is useful in identifying PMR in the setting of large vessel vasculitis (LVV)-GCA. Methods: Patients diagnosed with LVV-GCA by PET-CT at a tertiary referral hospital for a population of 450,000 people over a two-year period were reviewed. Scoring was performed based on potential significant FDG uptake at up to 16 sites in nine different extravascular areas (SCORE 16). Differences in extravascular sites of significant FDG uptake were evaluated between LVV-GCA with a clinical diagnosis of PMR or not. Results: Fifty-four patients were diagnosed with LVV-GCA by 18F-FDG-PET-CT. Of them, 21 (38.8%) were clinically diagnosed with PMR. Significant extravascular FDG uptake was more frequently observed in those with a clinical diagnosis of PMR. In this sense, the SCORE 16 was higher in those with clinical PMR (5.10 ± 4.05 versus 1.73 ± 2.31 in those without a clinical diagnosis of PMR; p< 0.001). A SCORE 16 involving more than 4 sites of significant FDG uptake yielded a sensitivity of 52% and a specificity of 91% for establishing a clinical diagnosis of PMR associated with LVV-GCA. The best areas of significant FDG uptake to clinically identify PMR in patients with LVV were the shoulder, the greater trochanter and the lumbar interspinous regions with an area under the ROC curve of 0.810 (0.691-0.930). Conclusion: Significant extravascular 18F-FDG-PET-CT uptake may help establish a clinical diagnosis of PMR in patients with LVV-GCA. These patients are more commonly diagnosed with PMR if they have significant FDG uptake in the shoulder, greater trochanter, and lumbar interspinous areas.

Hollow and concrete-filled steel tubes (CFSTs) are widely used as columns in many structural systems and local buckling can occur when they are subjected to axial compression loading. The critical regions for the local buckling of the columns are near the ends of the column where the moments are the highest. To strengthen the critical regions of the CFSTs the CFRP provides a simple and effective method which used previously as an enhancement for both of strength and ductility. So, this study suggests investigating the axial load behaviour of CFST strengthened with CFRP using FE method after a verification study and then a various parametric studies were carried out to cover the effect of the CFRP layers, number, confinement length and position. The FE results proved that, one CFRP sheet with thickness equal to 1.2 mm was strengthened the composite column by 8.5%, two CFRP sheets with total thickness equal to 2.4 mm was strengthened the composite column by 23.5%, three CFRP sheets with total thickness equal to 3.6 mm was strengthened the composite column by 35.1% and four CFRP sheets with total thickness equal to 4.8 mm was strengthened the composite column by 44.5%. Moreover, this study proved that by strengthened the composite columns with CFRP sheets with different lengths, the axial load resistance was improved by 8.5%, 4.6%, 0.1% and 0.0% for length percentages 100%, 75%, 50% and 25% respectively.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

The present study conducts the phase analysis, microstructural characteristics, and mechanical property evaluation on the as-cast and quenched Ti-15Mo-xFe alloys with high iron content ranging from 4 to 12 weight percent. All the four alloys were produced in a button-arc melting furnace. Heat treatment in the form of solution treatment was performed in a muffle furnace at a temperature of 1100°C, with a 1-hour holding time. The samples were rapidly quenched in ice-brine. Various characterization techniques were used to analyze samples both in the as cast and quenched conditions. X-ray diffractometer (XRD) was used to analyses the phases present in each alloy whereas the optical microscope (OM) was employed to track the microstructural evolution. The mechanical properties of the alloys were evaluated using a tensile test method while the micro-Vickers hardness measurements were conducted to evaluate hardness of the alloys. OM micrographs revealed equiaxed β grains and substructures in as-cast TMF0, dendritic structure, and equiaxed β grains with pores forming around the grain boundaries in TMF1, and micrograph full of dendrites and pores was observed in the as-cast TMF2 and TMF3 alloys. The quenched TMF0 showed only β equiaxed grains whereas TMF1, TMF2, and TMF3 revealed micrographs full of equiaxed grains of β phase with pores throughout the grain boundaries. The XRD patterns of cast TMF0 showed peaks belonging to the β and orthorhombic α″ martensitic phases and the quenched sample showed the bcc β phase only. The TMF1, TMF2, and TMF3 alloys in as-cast condition indicated peaks belonging to β , α″ and intermetallic B2 TiFe phases, however, their quenched samples showed the presence of β and Fe·Ti·O2 phases in TMF2 and TMF3 alloys. The tensile properties such as ultimate tensile strength (UTS) and elastic modulus (E) of as-cast TMF0 were 264 MPa and 79 GPa and these properties changed upon quenching to 411 MPa and 66 GPa respectively. The elastic modulus of TMF1 in as-cast condition was 74 GPa. The UTS and E of TMF1, TMF2, and TMF3 in as cast and quenched conditions were not recorded due to the fragility of the samples that failed prior to yielding any useful data. The micro-Vickers hardness in as cast and quenched conditions showed a similar trend with hardness increasing slightly upon quenching for TMF0, TMF1, and TMF3 alloys but slightly decreased in the case of TMF2. 6). The fracture surfaces of TMF0 exhibited both ductile and brittle fracture in as cast and quenched conditions whereas the only brittle fracture mode was observed in the TMF1, TMF2 and TMF3 alloys in both conditions.

Bulk composition, mineralogy and microchemistry of various fractions of the filling of the Crater No. 4 at Emmerting were investigated. Here we present mainly the fine fractions, which, in contrast to pebbles larger than ca. 4 cm, are relatively poor in material affected by melting. A 0.1 mm long meteorite fragment without ablation features was found, and remelted fragments of the same body have been identified. The projectile was dominated by enstatite, also containing forsterite, basic plagioclase, Ni-rich pyrrhotite and troilite, kamacite, silica, and probably merrillite. The molten fragments contain porous Mg-rich glass (indicating temperature &gt; 1500 °C), minor Fe oxides, and occasionally uncommon Ni-rich minerals. The bulk composition and electron microprobe show that the amount of meteoritic material is low (&lt;&lt; 1 %), and it is not unequivocally manifested even in platinum-group elements abundances and osmium isotope ratios (the latter, however, were only measured in two samples). This can be explained by dilution of the filling by particles brought after the crater formation, and by probably achondritic composition of the projectile. Relatively large hollow spheroid Fe oxide particles were observed in thin sections from the magnetic fraction. A Mn oxide hollow spherule has also been found. In magnetically separated filling from the nearby Crater No. 5, bulk chemical composition points to contamination with several metals and metalloids probably due to influence of recent alluvial sediments. Therefore, the extent of meteoritic contamination in this crater may be even smaller.

Nitrogen (N) and sulfur (S) are essential macro-elements crucial for the proper development, productivity, nutrient uptake, and the building blocks of protein biosynthesis. The plant's N-metabolism is also influenced by S, and its deficiency can lead to a decline in the consumption of N from fertilizers. The objective of this research was to assess the impacts Temporal N and S applications on the nutrient uptake, productivity, use efficiencies and micronutrients content status in soybean seeds. The field trial in randomized complete block design carried out, experiment comprised fourteen treatments with varying N and S quantities. N and S were applied through starter and temporal applications in different combinations. The findings indicated that temporal application of individually N and S fertilization as 25 kg ha-1 as starter and 25 kg ha-1 as temporal applications at R2 stage enhanced the highest nutrient uptake, seeds and stalks yields. The use efficiencies, as well as the Zinc (Zn) and iron (Fe) uptake by seeds, showed an increase with the temporal application of both nutrients compared to the control. Furthermore, soil Zn and Fe contents were also enhanced with the temporal applications of nitrogen and sulfur fertilization. As a result, it could be decided that the nitrogen and sulfur temporal applications not only enhanced nutrient uptake, productivity and use efficiencies but also improved the micronutrient uptake by soybean. Furthermore, this practice contributed to an improvement in soil Zn and Fe content.

Keywords: Wall-like RC columns; Strengthening; FRP; NSM rebars; Steel plates; Testing; FE modeling; Preloading.

A two-year field experiment (2022–2023) was carried out to investigate the impact of different sowing periods (spring and winter) and nitrogen levels (0, 30, 60 kg/ha) on the phytoextraction potential of flax. The study site is characterized by high concentrations of heavy metals (Cd, Ni, Cu, Pb, Zn) and belongs to the Mediterranean climate type. Flax (var. Calista) was sown in the spring of 2022 and in the winter of 2023, following a split plot experimental design with three rep-lications, and applying low-input practices. Results showed that spring-sown flax produced short-er but thicker plants with significantly higher biomass (5.27 tn ha-1) when treated with 30 kg ha-1 N compared to winter-sown (2.30 tn ha-1) when treated with 60 kg ha-1 N. The concentration of contaminants in the aerial biomass varied according to metal type and sowing period. The higher biomass production in spring resulted in a higher quantity of heavy metals being removed from the soil, making flax a promising crop for phytoextraction purposes, especially in soils contami-nated with multiple heavy metals.

In this study, we evaluated the antibacterial effect against Staphylococcus aureus and Salmonella Typhimurium in fried fish paste using floating electrode-dielectric barrier discharge (FE-DBD) plasma (1.1 kV, 43 kHz, N2 1.5 m/s, 1-60 min). In addition, quality evaluation (pH, VBN) of fried fish paste was conducted after FE-DBD plasma treatment. When FE-DBD plasma was treated for 1, 5, 10, 20, 30 and 60 min, S. aureus decreased by 0.16-1.13 log10 CFU/g, and S. Typhimurium decreased 0.25-1.13 log10 CFU/g. Both decreased &gt; log10 CFU/g at 60 min. The D-value was 58.92 and R2 was 0.97 for S. aureus using first-order kinetics, and the D-value was 43.60 and R2 was 0.97 for S. Typhimurium using the Weibull model. There was no significant difference in pH after FE-DBD plasma treatment (p &gt; 0.05). However, volatile basic nitrogen (VBN) significantly decreased as the treatment time increased (p &lt; 0.05), and it was the lowest at 60 min to 3.46. Therefore, FE-DBD plasma treatment could be considered as a technology for preserving the quality of processed foods.

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

Abstract Purpose Despite a considerable amount of literature on dual-energy-CT(DECT) iodine uptake of the head and neck, the physiologic iodine uptake of this region has not been defined yet. This study aims to establish reference values for the iodine uptake of healthy organs to facilitate clinical application. Material and Methods: Consecutive venous DECT scans of head and neck were reviewed, and unremarkable exams were included (n=617). 35 region of interest measurements were performed in 16 anatomical regions. Iodine uptake was compared among different organs/tissues and subgroup analysis was performed (male [n=403] vs female [n=214]; young [n=207] vs middle-aged [n=206] vs old [n=204]; normal weight [n=314] vs overweight [n=196] vs obese [n=107]]). Results: Overall mean iodine uptake values ranged between 0.5 and 9.4mg/ml. Women showed higher iodine concentration in the cervical vessels and higher uptake for the parotid gland, masseter muscle, submandibular glands, sublingual glands, palatine tonsils, tongue body, thyroid gland, and the sternocleidomastoid muscle than men (p0.04). With increasing age, intravascular iodine concentrations increased as well as iodine uptake for cerebellum and thyroid gland, while values for tongue and palatine tonsils were lower compared to younger subjects (p0.03). Iodine concentrations for parotid glands and sternocleidomastoid muscles decreased with higher BMI (p0.004), while normal-weighted patients showed higher iodine values inside the jugular veins, other cervical glands, and tonsils versus patients with higher BMI (p0.04). Conclusion: Physiologic iodine uptake values of cervical organs and tissues show gender-, age-, and BMI-related differences, which should be considered in clinical routine of head and neck DECT.

Candidatus Accumulibacter belongs to phosphate-accumulating organisms (PAO) which exhibit cyclic metabolism and are capable of intracellular polyphosphate accumulation and their hydrolysis under feast-famine anaerobic-aerobic cycling. In consortia of activated sludge microorganisms, these bacteria are responsible for enhanced biological phosphorus removal (EBPR). The spectrum of the substrates used by Ca. Accumulibacter remains insufficiently studied. It was investigated by measuring the oxygen uptake rates (OUR) of Ca. Accumulibacter-enriched culture supplemented with 17 different organic substrates. The highest oxygen uptake rates values were observed in the presence of tryptone, volatile fatty acids (acetate, propionate, and butyrate), succinate, pyruvate, and amino acids (aspartate and glutamate). Phosphate dynamics in the medium under shifts from anaerobic to aerobic cultivation in batch experiments was studied for these compounds (except for tryptone). All tested substrates were shown to cause phosphate cycling (release in the anaerobic phase and uptake in the aerobic one), with OURs for the substrates correlating with the amount of phosphates consumed during the aerobic phase. It was concluded that OUR may be used as an indicator of the monosubstrates used by Ca. Accumulibacter in the anaerobic/aerobic cycle. The possible pathways for substrate transport and metabolism by Ca. Accumulibacter are discussed using the stoichiometric data and the results of metagenomic analysis.

Parkinson’s Disease (PD) is a neurodegenerative and progressive disease that impacts the nerve cells in the brain and varies from person to person. The exact cause of PD is still unknown, and the diagnosis of PD does not include a specific objective test with certainty. Although deep learning has made great progress in medical neuroimaging analysis, these methods are very susceptible to biases present in neuroimaging datasets. An innovative decorrelated deep learning technique is introduced to mitigate class bias and scanner bias while simultaneously focusing on finding distinguishing characteristics in resting-state functional MRI (rs-fMRI) data, which assist in recognizing the PD with good accuracy. The decorrelation function reduces the non-linear correlation between features and bias in order to learn bias-invariant features. The Parkinson’s Progression Markers Initiative (PPMI) dataset, referred to as a single scanner imbalanced dataset in this study used to validate our method. The imbalanced dataset problem affects the performance of the deep learning framework by overfitting to the majority class. To resolve this problem, we propose a new Decorrelated Convolutional Neural Networks (DcCNN) framework by applying decorrelation-based optimization to Convolutional Neural Networks(CNN). An analysis of evaluation metrics comparisons shows that integrating the decorrelation function boosts the performance of PD recognition by removing class bias. Specifically, our DcCNN model performs significantly better than existing traditional approaches to tackle the imbalance problem. Finally, the same framework can be extended to create scanner invariant features without significantly impacting the performance of a model. The obtained dataset is a multi-scanner dataset which leads to scanner bias due to the differences in acquisition protocols and scanners. The multi-scanner dataset is a combination of two datasets, namely PPMI and FTLDNI - frontotemporal lobar degeneration neuroimaging initiative (NIFD) dataset. The results of t-distributed stochastic neighbor embedding (t-SNE) and scanner classification accuracy of our proposed Feature Extraction-DcCNN (FE-DcCNN) model validated the effective removal of scanner bias. Our method achieves an average accuracy of 77.80% on a multi-scanner dataset for differentiating PD from healthy control, which is superior to the DcCNN model trained on a single scanner imbalanced dataset.

In the aerospace sector, structural and non-structural components are usually subjected to a wide range of environmental conditions. Although lightweight, the use of composite parts for these applications is restricted, due to their poor performance in severe environmental conditions. Specifically, moisture can seriously damage the materials' performance, reducing their mechan-ical, thermal, electrical, and physical properties as well as the service time. A strategy to improve the materials’ resistance in humid environments is the use of protective lightweight barrier coatings to reduce the diffusion of gases and/or liquids in composites. Nanolamellar nanocom-posite characterized by the high in-plane orientation of nanoplatelets effectively works as barrier structures by generating tortuous paths for molecule diffusion. In this work, the effectiveness of protection against water uptake of nanocomposites reinforced with Graphite NanoPlatelets (GNPs) at high filler content (70, 80 and 90%wt) for Kevlar sandwich panels of a nacelle engine of an ATR42 aircraft has been investigated. Moisture uptake and Ground Air Ground (GAG) tests were carried out in an environmental chamber to reproduce temperature and relative humidity profiles representative of a real-scale application for a regional aircraft composite part. The high filler content of the graphene films ensures a high level of tortuosity by delaying and reducing moisture absorption by –71% compared to the unprotected panel, showing good barrier properties.

Microbial-mediated biogeochemical cycling of iron is widespread in anaerobic environments such as sediments and deep Earth aquifers, and is one of the major pathways for metabolising iron in nature. Organic matter containing quinone groups can act as electron shuttles to transfer electrons between microorganisms and Fe(III) oxides, facilitating the biotransformation of iron; this process also influences the transport transformation of pollutants. In this paper, the reduction of Fe(III) oxides by aniline in the heterogeneous iron-reducing bacterium Shewanella oneidensis MR-1 mediated by the electron shuttle AQS was investigated. The results showed that aniline significantly promoted the reduction of Fe(III) by MR-1 in the AQS-mediated reaction, and the best Fe(III) reduction was achieved in the reaction group of "GT+MR-1+0.5mM AQS+3μM aniline", in which the Fe(II) production was significantly higher than that in the reaction groups of only microorganisms and no aniline reaction. The amount of Fe(II) produced was significantly higher than that of the microorganism-only and aniline-free reaction groups, and the addition of aniline also significantly increased the consumption of sodium lactate by MR-1 in the reaction system. The solid mineral Fe(II)-O content increased to 41.32% after the reaction. However, the structure of needle ferrite is relatively stable, and the surface morphology did not change significantly by SEM, and the generation of other secondary minerals was not observed in the XRD results. The results of this experimental study can help to understand the biogeochemical cycle of iron in multicomponent reactions and are of great significance for environmental management.

An in-depth understanding of the Se uptake and metabolism in plants is necessary for developing Se biofortification strategies. Thus, hydroponic experiments were conducted to investigate the associated processes and mechanisms of organic Se [selenomethionine (SeMet) and selenomethionine-oxide (SeOMet)] uptake, translocation, transformation and their interaction in wheat, in comparison to inorganic Se. Results showed that Se uptake by roots and the root-to-shoot translocation factor under the SeMet treatment were higher than those under the selenite, selenate, and SeOMet treatments. The uptake and translocation of SeMet were higher than those of SeOMet within 72 h, although the differences gradually narrowed with time. The uptake of SeMet and SeOMet was also sensitive to the aquaporin inhibitor: AgNO3 addition resulted in 99.5% and 99.9% inhibition of Se in root in the SeMet and SeOMet treatments, respectively. Once absorbed by root, were rapidly assimilated to other Se forms, and SeMet and Se-methyl-selenocysteine (MeSeCys) were the dominant species in SeMet and SeOMet-treated plants, while notably, an unidentified Se form was also found in the root and xylem sap under the SeMet treatment. In addition, within 16 h, SeOMet inhibited the uptake and translocation of SeMet, while the interaction was weakened with longer treatment time. Taken together, the present study provides new insights for the uptake and transformation processes of organic Se within plants.

The powdered sorbents were applied in a batch system under "static" conditions and showed a much higher adsorption capacity than the granular one. These type of sorbents are more suitable for small quantities of water with a high concentration of arsenic. The possibilities of using all the tested methods for arsenic removal have been evaluated, and a scheme of the technological process has been proposed.

As one of toxic Volatile Organic Pollutant (TVOCs), formaldehyde has a toxic effect on microorganisms, and then inhibits the biochemical process of formaldehyde wastewater treatment. Therefore, the selective degradation of formaldehyde is of great significance to achieve formaldehyde wastewater high-efficiency and low-cost treatment. This study constructed a heterogeneous Fe-ZSM-5/H2O2 Fenton system for selective degradation to target compounds. By bonding Fe3+ onto the surface of ZSM-5 molecular sieve, Fe-ZSM-5 was prepared successfully. XRD, BET and FT-IR spectral studies shown the prepared Fe-ZSM-5 was mainly composed of micropores. The influences of different variables on formaldehyde selective heterogeneous Fenton degradation performance were studied. The 93.72% formaldehyde degradation and the 98.15% selectivity of formaldehyde compared with glucose had demonstrated in the optimized Fenton system after 360 min. Notably, the resultant selective Fenton oxidation system had a wide range of pH suitability from 3.0 to 10.0. Also, the Fe-ZSM-5 was used in 5 consecutive cycles, while the degradation efficiency of formaldehyde did not drop dramatically. Using reactive oxygen species scavengers, hydroxyl radical was the main active substance to degrade formaldehyde. Furthermore, the great degradation performance of this system to high concentration of formaldehyde was acquired, and the degrading efficiency was more than 95%.

Soil cadmium (Cd) contamination has become a serious problem in China. In this study, the goals of the field experiments were to understand how the application of nitrogen fertilizer at the full heading stage and filling stage reduced the uptake of Cd in rice by affecting the distribution of Cd in iron plaques on the root surfaces and subcellular in the root and flag leaf. The hydroponic culture experiments aimed to explore the effect of interaction or deficiency of nitrogen and cadmium on cadmium accumulation in rice at the late growth stage. The results showed that under the condition of having enough nitrogen supply during the early growth stage, applying nitrogen fertilizer during the full heading stage and filling stage resulted in a significant increase in the concentration of Fe and Cd on the root plaques at the milk stage and mature stage. Additionally, it increased the concentration and proportion of Cd in the soluble fraction of subcellular in the flag leaves at the milk stage. On the other hand, when there was a deficiency of nitrogen, the concentration of Fe in the root plaques increased significantly, while the concentration of Cd in the root plaques decreased significantly. Moreover, the proportion of Cd in the flag leaf cell walls increased significantly. Regardless of whether there was sufficient or deficient nitrogen supply during the early growth stage, applying nitrogen at the full heading stage reduced the Cd concentration in brown rice by 35.11% and 57.25%, respectively. Under hydroponic culture conditions with both Cd exposure and later-stage nitrogen supply significantly increased the Cd concentration in brown rice. However, in the absence of Cd, nitrogen supply significantly reduced the Cd concentration in brown rice. The accumulation of Cd in brown rice was significantly correlated with the accumulation of Fe and Mn at the late growth stage. Our findings indicate that when there is sufficient nitrogen nutrition during the early growth stage of rice, topdressing nitrogen fertilizer at the full heading stage combined with lime with mineral element fertilizers such as Fe and Mn is an effective approach to reduce the presence of cadmium in rice grains.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

We have designed cell penetrating peptides that target the leucine zipper transcription factors ATF5, CE-BPB and CEBPD and that promote apoptotic death of a wide range of cancer cell types, but not normal cells, in vitro and in vivo. While such peptides have the potential for clinical application, their mechanisms of action are not fully understood. Here, we show that one such peptide, Dpep, compromises glucose uptake and glycolysis in a cell-context-dependent manner (in about 2/3 of cancer lines assessed). These actions are dependent on induction of tumor suppressor TXNIP (thioredoxin interacting protein) mRNA and protein. Knockdown studies show that TXNIP significantly contributes to apoptotic death in those cancer cells in which it is induced by Dpep. The metabolic actions of Dpep on glycolysis led us to explore combinations of Dpep with clinically approved drugs metformin and atovaquone that inhibit oxidative phosphorylation and that are in trials for cancer treatment. Dpep showed additive to synergistic activities in all lines tested. In summary, we find that Dpep induces TXNIP in a cell-context-dependent manner that in turn sup-presses glucose uptake and glycolysis and contributes to apoptotic death of a range of cancer cells.

Malaria parasites increase their host erythrocyte’s permeability to obtain essential nutrients from plasma and facilitate intracellular growth. In the human P. falciparum pathogen, this increase is mediated by the plasmodial surface anion channel (PSAC) and has been linked to CLAG3, as encoded by one member of the conserved clag multigene family. Whether paralogs encoded by other clag genes also contribute to PSAC formation or serve unrelated roles remains unknown. Here, we generated transfectant lines carrying epitope-tagged versions of each CLAG. Each paralog colocalized with CLAG3, with concordant trafficking via merozoite rhoptries to the host erythrocyte membrane of newly-invaded erythrocytes. Each also exists within infected cells in at least two forms: an alkaline-extractable soluble form and a form integral to the host membrane. Like CLAG3, CLAG2 has a variant region cleaved by extracellular protease but CLAG8 and CLAG9 are protease-resistant. Paralog knockout lines, generated through CRISPR/Cas9 transfection, exhibited uncompromised growth in PGIM, a modified medium with more physiological nutrient levels; this finding is in marked contrast to a recently reported CLAG3 knockout parasite. CLAG2 and CLAG8 knockout lines exhibited compensatory increases in transcription of remaining clags and associated rhoph genes, yielding increased PSAC-mediated uptake to specific solutes. We also report distinct transport properties of these knockout lines, suggesting partially overlapping roles of CLAG paralogs in PSAC activity. We propose that the nutrient channel pore is formed by a higher order assembly of CLAG proteins at the host membrane.

Our environment has been significantly impacted by man-made pollutants, primarily due to industries make substantial use of synthetic chemicals, resulting in significant environmental consequences. In this research investigation, the co-precipitation approach was employed for the synthesis of cellulose-based ferric oxide (Fe₂O₃/cellulose) and copper oxide nanoparticles (CuOx-NPs). Scanning electron microscopy (SEM) analyses were conducted to determine the properties of the newly synthesised nanoparticles. Furthermore, the synthesized nanoparticles were employed for eliminating chromium from aqueous media under various conditions, including temperature, contact time, adsorbent concentration, adsorbate concentration, and pH. Additionally, the synthesised materials were used to recover Cr(VI) ions from real samples, including tap water, seawater, and industrial water, and the adsorptive capacity of both materials evaluated under optimal conditions. The synthesis of Fe₂O₃/cellulose and CuOx-NPs proved to be effective, as indicated by the outcomes of the study.

Laser-Powder Directed Energy Deposition (DED-LB/Powder) is an additive manufacturing process that is gaining popularity in the manufacturing industry due to its numerous advantages, particularly in repairing operations. However, its application is often limited to case studies due to some critical issues that need to be addressed, such as the degree of internal porosity. This paper investigates the effect of the most relevant process parameters of the DED-LB/Powder process on the level and distribution of porosity. Results indicate that, among the process parameters examined, porosity is less affected by travel speed and more influenced by powder mass flow rate and laser power. Additionally, a three-dimensional finite element transient model was introduced, which was able to predict the development and location of lack-of-fusion pores along the building direction.

: Greenhouse plants are usually grown in containers filled with growing media. Peat is the main component of the growing media used in greenhouses. However, peat substrate is made from peat from drained peatlands, which is a limited resource. Wood fiber can be an alternative to use as a growing media for controlled-climate crops. The chemical properties of the growing media interact and change continuously due to the small volume of the growing media, which is limited by the vegetative container. Therefore, this study aims to gain new knowledge on the impact of nutrient changes in the microbial degradation of carbon compounds in wood fiber and mixtures with peat substrate on the content and uptake of nutrients required by plants. Cucumbers (Cucumis sativus L.) were cultivated in growing media of peat substrate and wood fiber: (1) peat substrate (PS); (2) wood fiber (WF); (3) wood fiber and peat substrate 50/50 v/v (WF/PS 50/50); (4) wood fiber and peat substrate 25/75 v/v (WF/PS 25/75). The rates of fertilization were the following: (1) conventional fertilization (CF); (2) N13; (3) N23; (4) N30. Fertilization of cucumbers with different rates of nitrogen influenced the nutrient uptake. Plants grown in WF/PS 50/50 and WF/PS 25/75 growing media had the best Cu uptake when fertilized with N23. When the plants grown in the wood fiber media and the 50/50 media were fertilized with N13, N23, and N30, the Mn content in the growing media at the end of the growing season was significantly lower than the Mn content in the media with conventional fertilization. Thus, nitrogen improved the uptake of Mn by plants grown not only in the wood fiber but also in combinations with peat substrate. Growing plants in wood fiber and fertilizing them with N13 can result in optimum uptake of micronutrients. The number and mass of cucumber fruits per plant were influenced by the amount of wood fiber in the growing media and the application of nitrogen fertilizer. The highest number of fruits and mass of fruits per plant was obtained significantly higher when cucumbers were grown on WF/PS 50/50 growing media with additional N13 fertilization.

Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.