The aim of this paper is to create a sensor model based on optical crystal fibers (PCF). The aim of this model is to find and identify zinc cadmium. This thesis looked at three different categories of concentrations. For sensor architecture, PCF was generated using single-mode fiber-to-end split fusion (SM-PCF-SM). In this experiment, a specific wavelength spectrum was used to alter the concentration of materials covering the fiber in order to demonstrate the fiber's sensing capability. The 550nm wavelength has been used as the optical source for the fiber. The change in the output power of the external light was monitored and changes were observed for each concentration of the concentrations around the fiber. It has been found that the fiber is sensitive to small changes in concentrations. The absorption of the fiber has been calculated for the incoming capacity, as well as the losses in the capacity outside the fiber.

A novel 8-channel demux device based on multicore photonic crystal fiber (PCF) structures that operate at C-band range (1530-1565nm) has been demonstrated. The PCF demux design is based on replacing some air-holes areas with lithium niobate and silicon nitride materials over the PCF axis alongside with the appropriate optimizations of the PCF structure. The beam propagation method (BPM) combined with Matlab codes were used to modeled the demux device and to optimized the geometrical parameters of the PCF structure. Simulation results show that 8-channel can be demultiplexing after light propagation of 5 cm with large bandwidth (4.03-4.69nm) and crosstalk ((-16.88)-(-15.93) dB). Thus, the proposed device has a great potential to be integrated in dense wavelength division multiplexing (DWDM) technology for increasing performances in networking systems.

In this paper, a sensitivity sensor of dual-core photonic crystal fiber (DC-PCF) filled with magnetic liquid is introduced and investigated by the finite element method (FEM). To regulate the energy coupling involving the two cores, the magnetic fluid is filled into the pore between the two cores. To adjust the coupling between the supermodes in the DC-PCF, the refractive index of the magnetic fluid-filled air hole may change due to the external magnetic field. This specifically created a magnetic fluid-filled DC-PCF, the magnetic fluid-filled hole is not used as the core for energy transmission, thus avoiding transmission loss. The dip wavelength and the magnetic field displayed an excellent linear connection between 80 and 260 Oe, depending on the numerical data. The detection sensitivity of the magnetic field reached 515.75 pm/Oe at a short fiber length of 482 m. The designed magnetic fluid-filled DC-PCF has high sensitivity and small volume and has great application prospects in medical and industrial field magnetic field detection.

This work proposes a hollow-core photonic crystal fiber-based edible oil sensor in the terahertz (THz) range (e.g., 1.0THz ≤ f ≤ 3.0THz) and different sensing characteristics are numerically analyzed. The suggested sensor’s performance was assessed by means of COMSOL Multiphysics, a commercial program that uses the finite element approach. The computational results indicate that the relative sensitivity is 85.591%, 84.648%, 82.625%, 82.683%, and 79.161%, respectively, at f = 2.2 THz, for several types of sunflower oil, mustard oil, coconut oil, olive oil and palm oil; and the corresponding effective areas are 7.22×10-8 um2, 7.09×10-8 um2, 6.83×10-8 um2,7.09×10-8 um2, 6.5231 ×10-8 um2. In addition, the effective material loss for sunflower oil, muster oil, coconut oil, olive oil, and palm oil has been found to be 0.02561 cm-1, 0.027054 cm-1, 0.030322 cm-1, 0.028854 cm-1 ,0.035427cm-1 respectively. Moreover, the proposed sensor also has low confinement loss are 1.55×10-8 dB/m, 1.63×10-8 dB/m, 1.31×10-8 dB/m, 1.99×10-8 dB/m, 4.0345×10-8 dB/m.This proposed sensor can be fabricated using extrusion and 3D-printing technologies, and due to its augmented detecting capabilities, it can be a vital part of oil sensing devices implemented in real life such as industry fields.

Silicon-based photonic integrated circuit (PIC) is a research focus in producing high-density photonics. One of the potential applications of silicon PIC is the sensing and measurement system. In this work, we use the one-dimensional photonic crystal (1D-PhC) cavity design which and utilize it at the PIC level design. The 1D PhC design used as the compact model has the same characteristics as experimentally demonstrated in previous works. The compact model is made from the S-parameter extraction of the 1D-PhC device which is done by using Lumerical FDTD software. The PIC design integrates the 1D-PhC device as a sensing component with a PN-phase shifter (PN-PS) to function as a refractive index (RI) sensor calibration or tuning circuit. A custom design of PN-PS device is used by simulating and extracting the bias voltage-effective index (bias-Neff) data by using Lumerical DEVICE and MODE into the circuit simulator. The circuit-level simulation is done by using Lumerical Interconnect software. Finally, we show the GDSII layout design of the 1D-PhC based photonic sensor calibration circuit with an analysis of generic silicon PIC design rules. The designed PIC is applicable for the bio-sensing applications and photonic SOC component. This work also shows the promise of PIC design approach for further PIC development.

Application of pulsed optical sources on the base of stable mode-locked lasers, which are known for their very low time jitter, provides the opportunity for creation a high precision photonic analogue to digital converters of signals in the microwave range. However, the repetition rate of modern commercially available mode-locked lasers is limited to a few gigahertz. The increase of repetition rate is possible using the schemes that implement a passive chirp of ultra-short pulses prior to electro-optic amplitude modulator, which is driven by the signal under test, and demultiplexing of modulated signal after a modulator. In the given article we analyzed a continuous time-stretch chirp using single mode fiber as dispersive element. The limitations of input signal bandwidth and source pulses energy are considered.

We have developed circular defects in 2-dimensional photonic crystal lasers that allow current injection for interconnected optical communications. However, when cleaving the sample to measure the output light, the output light intensity changes due to the cleaving position. In a previous study, we discovered through simulation that this effect could be eliminated and that a higher optical output might be obtained by applying a convex edge structure. In this paper, we develop the fabrication technology for this structure, fabricate samples, and measure the output light experimentally. Room-temperature continuous-wave laser oscillations using this structure are observed. The laser threshold is similar to well-lasing samples with normal cleavage edge faces. We are assured that these results contribute to future work such as accurate manufacturing and improving the end-face configuration to obtain higher outputs.

This study introduces an innovative integration of hyperbolic metamaterials (HMMs) and photonic crystals (PtCs), each possessing unique dispersion properties that effectively manipulate the propagation of light. We present a PtC waveguide consisting of arrays of HMM nanorods, denoted as HMM PtCs. This waveguide configuration enables the realization of a high figure of merit (FOM) nano-sensor. By modifying the refractive indices of the surrounding materials, the PtC waveguide exhibits alterations in absorption and transmission, allowing for the detection of temperature, pressure, and material variations. Numerical methods were employed to demonstrate the remarkable efficiency of this proposed system, achieving a sensitivity of 324.16 nm/RIU (refractive index unit) and an impressive FOM of 469.58 RIU−1. These results signify a substantial improvement over surface plasmonic sensors, which typically exhibit limited FOMs. As a consequence, the HMM PtC waveguide sensor emerges as an exceptionally appealing option for photonic sensing applications. The proposed HMM PtC waveguide holds vast potential across diverse fields, including biology, medicine, and clinics, representing an exciting advancement for both industry and scientific research.

A total internal reflection photonic crystal fiber (PCF) based on hexagonal core is proposed for gas sensing in a specific wavelength range. The higher sensitivity and lower confinement loss were realized by the structure of the proposed PCF consists of two layers with circular holes rotated hexagonally around a core region and six slotted air-hole in the cladding based on numerical analysis. The simulation results show that the enhancement of the relative sensitivity has been done by enhancing the diameter of the hexagonal shape air-hole cladding (d1) and the hexagonal arranged holes around the central solid core (d0) in this design. Also, the confinement loss has been reduced by enhancing the ratio of length to width of slotted holes (l/w) and decreasing the cladding air-hole diameters (d1). As the refractive index increases, the wavelength shifts toward the long wavelength. And in a certain temperature range, the transmission characteristics of the device does not change with the temperature. The results are helpful for designing high performance PCF for gas sensing applications.

Current generation witnesses a huge interest in optical waveguide due to their salient feature such as low cost, immune to electromagnetic interference, easy to multiplex, compact size, etc. These features of the optical fibers makes it an useful tool for various sensing applications including medicine, automotive, biotechnology, food quality control, aerospace, physical and chemical monitoring etc. Among all the reported application, the device has been widely exploited to measure the physical and chemical variation in surrounding environment. Optical fiber based temperature sensor plays a crucial role in this decade to detect high fever and tackle COVID like pandemic. Recognizing the major developments in the field of the optical fibers, this article aims to provide recent progress in temperature sensor utilizing several sensing configuration including standard fiber, photonic crystal fiber, and Bragg grating fibers. Additionally, the article also highlights the advantages, limitations, and future possibilities in this area.

Herein, we offer a numerical study on the devising of a unique 2D-heterostructure Photonic crystal (PC) that can split two orthogonally polarized light waves. The analysis is performed via a two-dimensional finite element method (2D-FEM) by utilizing COMSOL Multiphysics software. The device consists of two discrete designs of PC formation. The first PC formation is optimized so that it permits both TE and TM-polarization of light to transmit through it. Whereas the second PC formation possesses a Photonic Bandgap (PBG) only for TE-polarized light. These two formations are combined at an angle of 45 degrees, resulting in a reflection of self-collimated TE-polarized light at an angle of 90 degrees owing to the PBG present in the second PC formation. While permitting the self-collimated TM-polarized light wave to travel uninterrupted. The proposed device has a small footprint of ~10.5 μm2 offering low transmission loss and high polarization extinction ratio which makes it an ideal candidate to be employed as an on-chip polarization division multiplexing system.

Based on the sensitive sum frequency generation cross-correlation frequency-resolved optical gating (SFG-XFROG) measurement setup, besides the pulse broadening, blue shift, red shift and obvious pulse acceleration, we observed the soliton evolution when the low energy soliton pulse with wavelength of 1555nm transmit through the Si photonic crystal waveguide. The measurements were nicely matched with the simulation results, which are achieved with an optimized nonlinear Schrödinger equation (NLSE) modeling. The effects of various parameters of the silicon photonic crystal waveguides and the incident pulses on the pulse transmission were also analyzed, including the nonlinear effects and dispersion such as the self-phase modulation (SPM), self-steepening (SS) and intra-pulse Raman scattering(IRS). The results help us understand further the ultra-fast nonlinear dynamics of soliton in silicon-based waveguides, and even open a novel way for soliton-based functional elements in CMOS-compatible platforms.

The interest in random fiber lasers (RFLs), first demonstrated one decade ago, is still growing and their basic characteristics have been studied by several authors. RFLs are open systems that present instabilities in the intensity fluctuations due to the energy exchange among their non-orthogonal quasi-modes. In this work, we present a review of the recent investigations on the output characteristics of a continuous-wave erbium-doped RFL, with emphasis on the statistical behavior of the emitted intensity fluctuations. A progression from the Gaussian to Lévy and back to the Gaussian statistical regime was observed by increasing the excitation laser power from below to above the RFL threshold. By analyzing the RFL output intensity fluctuations, the probability density function of emission intensities was determined, and its correspondence with the experimental results was identified, enabling a clear demonstration of the analogy between the RFL phenomenon and the spin-glass phase transition. A replica-symmetry-breaking phase above the RFL threshold was characterized and the glassy behavior of the emitted light was established. We also discuss perspectives for future investigations on RFL systems.

Increasing the quality factor (Q) of an optical resonator device has been a research focus to be utilized in various applications. Higher Q-factor means light is confined in a longer time which will produce a shaper peak and higher transmission. In this paper, we introduce a novel technique to increase further the Q-factor of a one-dimensional photonic crystal (1D PhC) cavity device by using an end loop-mirror (ELM). The technique utilizes and recycles the light transmission from the conventional 1D PhC cavity design. The design has been proved to work by using the 2.5D FDTD simulation with Lumerical FDTD and MODE softwares. By using the ELM technique, the Q- factor of a 1D PhC design has been shown to have increased up to 79.53 % from the initial Q value without the ELM. This novel design technique can be combined with any high Q-factor and very high Q-factor designs to increase more the Q-factor value of a photonic crystal cavity devices or any other suitable optical resonator devices. The experimental result shows that the device is measurable by adding a Y-branch component to the one-port structure and able to get the high-Q result.

The spectral properties of a one-dimensional photonic crystal bounded by a resonant absorbing nanocomposite layer with the near-zero permittivity have been studied. The problem of calculating the transmittance, reflectance, and absorptance spectra of such structures at the normal and oblique incidence of light has been solved. It is shown that, depending on the permittivity sign near zero, the nanocomposite is characterized by either metallic or dielectric properties. For the first time, the possibility of simultaneous formation of the Tamm plasmon polariton at the photonic crystal/metallic nanocomposite interface and the localized state similar to the defect mode with the field intensity maximum inside the dielectric nanocomposite layer is demonstrated. Specific features of field localization at the Tamm plasmon polariton and defect mode frequencies are analyzed.

This study aims to theoretically address the design and analysis of an efficient pressure sensor designed by using a polymer-based defective 1D annular photonic crystal (APC). The 1D APC comprises an alternate arrangement of Si and SiO2 in a cylindrical fashion, incorporating a central defect layer. The investigation of the reflectance characteristics of the proposed structure is conducted by separately considering the polystyrene (PS) and the polymethyl methacrylate (PMMA) polymer materials as the defect layer. The pressure-sensitive refractive index of the polymers and the constituent materials of the APC plays a vital role in envisaging the pressure-sensing application. The cornerstone of this study is represented by the shift analysis in the wavelength of the defect mode inside the band gap using different applied pressures by employing the modified transfer matrix method (MTMM). Various geometrical parameters like the defect polymer layer’s thickness and the APC period were carefully optimized to achieve higher sensing performance. The proposed design demonstrated a remarkable pressure sensitivity and FoM of 51.29 nm/GPa and 301.7 GPa-1, respectively, which is considerably high in the current research scenario. It is believed that the proposed structure can be an apt candidate as an innovative high-performance pressure sensor, and it can play a key role in photonic integrated circuits.

Five years ago, the concept of addressed fiber Bragg structures (AFBS) was proposed, which simultaneously perform the functions of a two-frequency radiation shaper, the difference frequency of which is the AFBS address, and a sensitive element, since the value of the difference frequency is invariant to measured physical fields, and the set of difference frequencies, moreover, is orthogonal in the array of such sensors, enabling their address multiplexing. In this article, we provide an overview of the theory and technology of AFBS, including the structures with three or more spectral components with various combinations of difference frequencies, symmetrical and asymmetric, performing the functions of the address and converting information signals to the low-frequency range at the same time, along with other functions. The subjects of interrogation of these structures, their fabrication and calibration are discussed as well. We also consider a wide range of applications in which AFBS can be used, covering such areas as oil and gas production, power engineering, transport, medicine, etc. In addition, the prospects of AFBS further development are proposed.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

The work presents an approach to instrument the load sensing bearings for automotive applications for estimation of the loads acting on the wheels. The system comprises fiber-optic sensors based on addressed fiber Bragg structures (AFBS) with two symmetrical phase shifts. A mathematical model for load-deformation relation is presented, and the AFBS interrogation principle is described. The simulation includes (i) modeling of vehicle dynamics in a split-mu braking test, during which the longitudinal wheel loads are obtained, (ii) the subsequent estimation of bearing outer ring deformation using a beam model with simply supported boundary conditions, (iii) the conversion of strain into central wavelength shift of AFBS, and (iv) modeling of the beating signal at the photodetector. The simulation results show that the estimation error of the longitudinal wheel force from the strain data acquired from a single measurement point was 5.44% with root-mean-square error of 113.64 N. A prototype load sensing bearing was instrumented with a single AFBS sensor and mounted in a front right wheel hub of an experimental vehicle. The experimental setup demonstrated comparable results with the simulation during the braking test. The proposed system with load-sensing bearings is aimed at estimation of the loads acting on the wheels, which serve as input parameters for active safety systems, such as automatic braking, adaptive cruise control, or fully automated driving, in order to enhance their effectiveness and safety of the vehicle.

This article reveals a best possible design for hybrid dispersion compensating fiber (HyDCF) with high birefringence established on modified broadband compensating structure through S, C and L telecommunication bands. The simulation outcome exhibits relatively higher birefringence of 3.76×10-2 at wavelength of 1550 nm. The suggested fiber also has dispersion compensation characteristics in an inclusive series of wavelengths which covers 1400-1625 nm. The reported design can achieve dispersion quantity of – 606 ps/ (nm.km) at 1550 nm effective wavelength. The reported fiber design matches the relative dispersion slope (RDS) 0.003694 nm-1 similar to single mode fiber at 1550 nm operating wavelength. This fiber demonstrates negatively flattened effective dispersion of – 2.703 ± 0.734 ps/ (nm.km) within 180 nm flat band ranging from 1460-1640 nm wavelength. It is also convenient to optical high bit rate communication systems. The low confinement loss is found 3.756×10-10 dB/m at the operating wavelength. This design also achieves highly nonlinear coefficient of 50.34 W-1km-1. In some cases, it can also be used in sensing applications.

A realistic implementation of an all-fiber CO₂ sensor, using 74 cm of hollow core PCF fiber as the cavity for light/gas interaction, has been implemented. It is based on CO₂ absorbance in the 2 μm region. The working range is from 2% to 100% CO₂ concentration at 1 atm total pressure. The response time obtained was 10 min. The use of an FBG tuned fiber ring laser, specifically designed for this application, is discussed and preliminary results with this laser are also presented.

Environmental monitoring is an important topic and serves a vibrant scientific role by revealing long-term trends that can lead to new knowledge and understanding. Globally, there is active development of photonic sensors incorporating multidisciplinary research. The ultimate objective is to develop small, low-cost, sensitive, selective, quick, durable, remote-controllable sensors that are resistant to electromagnetic interference. Different photonic sensor designs and advances in photonic frameworks have shown the possibility to realize these capabilities. In this review paper, the latest developments in the field of optical waveguide and fiber-based sensors which can serve for environmental monitoring are discussed. Several important topics such as toxic gas, water quality, indoor environment, and natural disaster monitoring are reviewed.

MPC (Magneto-Photonic Crystal) Optimisation is a feature-rich Windows software application designed to enable researchers to analyze the optical and magneto-optical spectral properties of multilayers containing gyrotropic constituents. A set of computational algorithms aimed at enabling the design optimization and optical or magneto-optical (MO) spectral analysis of 1D magnetic photonic crystals (MPC) is reported, together with its Windows software implementation. Relevant material property datasets (e.g., the optical spectra of refractive index, absorption, and gyration) of several important optical and MO materials are included, enabling easy reproduction of the previously published results from the field of MPC-based Faraday rotator development, and an effective demonstration-quality introduction of future users to the multiple features of this package. We also report on the methods and algorithms used to obtain the absorption coefficient spectral dispersion datasets for new materials, for which the film thickness, transmission spectrum, and refractive index dispersion function are known.

We report the effect of doping Cd1-xZnxS/ZnS core/shell quantum dot (CSQDs) in nematic liquid crystal p-methoxybenzylidene p-decylaniline (MBDA) at 0.05 wt/wt%, 0.1 wt/wt%, 0.15 wt/wt%, 0.2 wt/wt%, 0.25 wt/wt% and 0.3 wt/wt% concentrations of CSQDs in MBDA. Dielectric parameters with and without bias with respect to frequency has been investigated. The change in electro - optical parameters with temperature has also been demonstrated. The increase in the mean dielectric permittivity has been found due to large dipole moment of CSQDs which impose stronger interactions with the liquid crystal molecules. The dielectric anisotropy changes sign on doping CSQDs in MBDA liquid crystal. It was concluded that the CSQDs doping noticeably increases the dielectric permittivity of nematic MBDA in the presence of electric field. The doping of CSQDs in nematic MBDA liquid crystal reduces the ion screening effect effectively. This phenomenon is attributed to the competition between the generated ionic impurities during assembling process and the ion trapping effect of the CSQDs. The rotational viscosity of nematic liquid crystal decreases with increasing concentration of the CSQDs with faster response time observed for 0.05 wt/wt% concentration. The birefringence of the doped system increases with the inclusion of CSQDs in MBDA. These results find application in the field of display devices, phase shifters, industries and projectors.

The properties of photonic quasicrystals ultimate rely on their inherent long-range order, a hallmark that can be quantified in many ways depending on the specific aspects to be studied. We use the Lempel-Ziv measure, a basic tool for information theoretic problems, to characterize the complexity of the specific structure under consideration. Using the generalized Fibonacci quasicrystals as our thread, we adress the relation between the optical response and the associated complexity.

We present a simulation library in Python 3 called Lumos. Different optimization routines areimplemented using multiple instruments. Automated measurements are implemented in this librarywhich lead to faster measurements as compared to manual sweeps. We elaborate on the experimentalmethods and also example usage is mentioned.

With a recent advance in photonic integrated circuits (PIC), a new field of frequency agile coherent radar systems is being thoroughly researched. In contrast to the traditional all-electronics radiofrequency (RF) radar techniques, a fully photonics-based system does not suffer from bandwidth limitation and noise degradation when switching from S to X or K-band and can achieve excellent phase noise even at frequencies exceeding 20 GHz. However, recent state-of-the-art PICs still exhibit high processing losses in the optical domain, which must be addressed in the electrical part of the RF domain. This study presents a comprehensive analysis of the challenges in designing RF front-end amplifier chains for microwave photonic radars, particularly in maintaining stability, minimizing noise, and reducing intermodulation distortion. Furthermore, a comprehensive demonstration of the RF front-end, encompassing both the optical generation of RF signals and experimental measurements of a rotor blade's Doppler fingerprint to validate the system's performance is presented.

In contemporary science and technology, photonic sensors are essential. They may be made to be extremely resistant to some physical parameters while also being extremely sensitive to other physical variables. Most photonic sensors may be incorporated on chips and operate with CMOS technology, making them suitable for use as extremely sensitive, compact, and affordable sensors. Photonic sensors can detect electromagnetic (EM) wave changes and convert them into an electric signal due to the photoelectric effect. Depending on the requirements, scientists have found ways to develop photonic sensors based on several interesting platforms. In this work, we extensively reviewed the most generally utilized photonic sensors for detecting vital environmental parameters and personal healthcare. These sensing systems include optical waveguides, optical fibers, plasmonics, metasurfaces, and photonic crystals. Various aspects of light are used to investigate photonic sensors' transmission or reflection spectra. In general, resonant cavity or grating-based sensor configurations that work on wavelength interrogation methods are preferred, so these sensor types are mostly presented. We believe this paper will provide insight into the novel types of available photonic sensors.

Microwave photonic (MWP) signal processors, which process microwave signals based on photonic technologies, bring advantages intrinsic to photonics such as low loss, large processing bandwidth, and strong immunity to electromagnetic interference. Optical microcombs can offer a large number of wavelength channels and compact device footprints, which make them powerful multi-wavelength sources for MWP signal processors to realize a variety of processing functions. In this paper, we experimentally demonstrate the capability of microcomb-based MWP signal processors to handle diverse input signal waveforms. In addition, we quantify the processing accuracy for different input signal waveforms, including Gaussian, triangle, parabolic, super Gaussian, and nearly square waveforms. Finally, we analyze the factors contributing to the difference in the processing accuracy among the different input waveforms, and our theoretical analysis well elucidates the experimental results. These results provide a guidance for microcomb-based MWP signal processors when processing microwave signals of various waveforms.

In this paper, a plasmonic refractive index sensor based on MIM waveguide (metal_insulation_metal) with two plasmonic waveguides and five rings and two teeth and four rectangular cavities is proposed and designed. The refractive index of the resonators as well as the resonant wavelengths will be investigated by the time difference finite difference method. To achieve an optical sensor with excellent quality and performance, we change the number and type of amplifiers and their dimensions. In each stage of the simulation, we will only change the refractive index of the middle ring located in the middle of the two waveguides, and the refractive index of the other amplifiers remains the same. This challenge will help to form a more appropriate structure for optical sensors. The sensor built in this simulation has a balanced and suitable function for integrated circuits and helps researchers to better understand the design of plasmonic structures. It also has important applications in medical research, health care, drug manufacturing, security monitoring and environmental protection, internal security of countries and the battlefield.

Microscopes based on dielectric mesoscale particles, using the effect of a photonic jet or terajet in the terahertz range, are a promising tool for overcoming the diffraction limit. However, the image they generate has limited contrast, which limits the application of this method. In this letter, we demonstrate that it is possible to increase the contrast of an image based on dielectric mesoscale particles that provide the formation of photonic hooks. In this case, the illumination of the object is carried out by an oblique incidence of subwavelength terajet, which significantly (more than 2 times) increases the contrast of the image.

We demonstrate a compact 4x4 wavelength selective switch with 50 % fewer electrical pads as compared with our previous generation. We report loss and crosstalk for different paths of the switch. We measure median loss of 5.32 dB and worst case crosstalk of -35 dB. The microring resonators tune by more than one free spectral range, which is an improvement over our previous generation of switches. This switch can support 8 channels at 400 GHz spacing. We conclude that it is not possible to drive both microring resonators with the same voltage and separate control is required because of fabrication variation of the current technology.

In this paper, we review devices used in silicon photonic switches. Devices in switches are divided into active and passive devices. Active devices consist of microring resonator, contra directional couplers, mach zhender switches. Passive devices consist of waveguide crossings and arrayed waveguide gratings. We also list the state of the art in devices in a comparison table.

We report an all-optical radio-frequency (RF) spectrum analyzer with a bandwidth greater than 5 terahertz (THz), based on a 50-cm long spiral waveguide in a CMOS-compatible high-index doped silica platform. By carefully mapping out the dispersion profile of the waveguides for different thicknesses, we identify the optimal design to achieve near zero dispersion in the C-band. To demonstrate the capability of the RF spectrum analyzer, we measure the optical output of a femtosecond fiber laser with an ultrafast optical RF spectrum in the terahertz regime.

Optical switches are a key element in modern network communications. We present the results of experimental verification of a new theoretical concept proposed earlier for a full-optical wavelength-selective dual-channel switch based on the photonic hook effect, which is free from using any micro-mechanical devices or nonlinear materials. A large-scale laboratory prototype of such a device based on an off-axis Wood zone plate is considered and its main parameters in the millimeter wavelength range are investigated On the basis of the experiments, we show that the optical isolation of switched channels for a switch based on an off-axis zone plate can achieve 15 dB at a frequency difference of 25 GHz in frequency range from 93 to 136 GHz. Given the scaling, these results can be transferred to another range, including the optical one.

We report a broadband radio frequency (RF) channelizer with up to 92 channels using a coherent microcomb source. A soliton crystal microcomb, generated by a 49 GHz micro-ring resonator (MRR), is used as a multi-wavelength source. Due to its ultra-low comb spacing, up to 92 wavelengths are available in the C band, yielding a broad operation bandwidth. Another high-Q MRR is employed as a passive optical periodic filter to slice the RF spectrum with a high resolution of 121.4 MHz. We experimentally achieve an instantaneous RF operation bandwidth of 8.08 GHz and verify RF channelization up to 17.55 GHz via thermal tuning. Our approach is a significant step towards the monolithically integrated photonic RF receivers with reduced complexity, size, and unprecedented performance, which is important for wide RF applications ranging from broadband analog signal processing to digital-compatible signal detection.

Drawing inspiration from biological brain's energy-efficient information-processing mechanisms, photonic integrated circuits (PIC) have facilitated the development of ultrafast artificial neural networks. This in turn is envisaged to offer potential solutions to the growing demand for artificial intelligence employing machine learning in various domains, from nonlinear optimization and telecommunication to medical diagnosis. At the meantime, silicon photonics has emerged as a mainstream technology for integrated chip based application. However, challenges still need to be addressed in scaling it further for broader applications due to the requirement of co-integration of electronic circuitry for control and calibration. Leveraging physics in algorithms and nanoscale materials holds promise for achieving low-power, miniaturized chips capable of real-time inference and learning. In this back drop, we present the state of the art in neuromorphic photonic computing, focusing primarily on architecture, weighting mechanisms, photonic neurons, and training while giving an over-all view on recent advancements, challenges, and prospects. We also emphasize and high light the need for revolutionary hardware innovations to scale up neuromorphic systems while enhancing energy efficiency and performance.

Micro-gyroscopes based on the Coriolis principle are widely employed in inertial navigation, motion control, and vibration analysis applications. This paper presents our main contributions which include a novel dual-frame optomechanical gyroscope, a unique photonic crystal cavity design, and advanced numerical simulation and optimization methods. The proposed design utilizes an optical cavity formed between dual oscillating frames, whereby input rotation induces a measurable phase shift via optomechanical coupling. Actuation of the frames is achieved electrostatically via an interdigitated comb-drive design. Through theoretical modeling based on cavity optomechanics and finite element simulation, the operating principle and performance parameters are evaluated in detail. Results indicate an expected angular rate sensitivity of 22.8 mV/°/s and angle random walk of 7.1×10-5 °/h1/2, representing superior precision than to existing micro-electromechanical systems gyroscopes of comparable scale. Detailed analysis of the optomechanical transduction mechanism suggests this dual-frame approach could enable angular vibration detection with resolution exceeding state-of-the-art solutions.

RF photonic transversal signal processors, which combine reconfigurable electrical digital signal processing and high-bandwidth photonic processing, provide a powerful solution for achieving adaptive high-speed information processing. Recent progress in optical microcomb technology provides compelling multi-wavelength sources with compact footprint, yielding a variety of microcomb-based RF photonic transversal signal processors implemented by either discrete or integrated components. Although operating based on the same principle, processors in these two forms exhibit distinct performance. This letter presents a comparative investigation into their performance. First, we compare the performance of state-of-the-art processors, focusing on the processing accuracy. Next, we analyze various factors that contribute to the performance differences, including tap number and imperfect response of experimental components. Finally, we discuss the potential for future improvement. These results provide a comprehensive comparison of microcomb-based RF photonic transversal signal processors implemented using discrete and integrated components and provide insights for their future development.

Two-dimensional arrays of hollow nanotubes made of TiO2 are a promising platform for sensing, spectroscopy and light harvesting applications. Their straightforward fabrication via electrochemical anodization, growing nanotube pillars of finite length from a Ti foil, allows precise tailoring of geometry and, thus, material properties. We investigate these photonic crystal structures with respect to reduction of front surface reflection, achievable field enhancement, and photonic bands. With the Rigorous Coupled Wave Analysis (RCWA), we study the optical response of photonic crystals made of thin-walled nanotubes relative to the bare Ti foil substrate, including under additional charge carrier doping.

Despite multiple classical outcomes arising from the quantum Rayleigh conversions of photons underlying the propagation of optical waves through dielectric media and the ensuing light-matter interactions, this quantum process has been largely ignored. Several of its outcomes are considered in this article from a physical perspective, e.g., inter-quadrature coupling of photons, phase-dependent amplification in optical directional couplers and related polarization rotation, phase-shifting of weak signals in the optically linear regime, location-dependent coupling coefficient for refractive index gratings, etc. A correct identification of these effects will enable useful design and operation of integrated photonic functional devices.

Gas sensing is crucial for detecting hazardous gases in industrial environments, ensuring safety and preventing accidents. Additionally, it plays a vital role in environmental monitoring and control, helping to mitigate pollution and protect public health. Integrated photonic gas sensors are important due to their high sensitivity, rapid response time, and compact size, enabling precise recognition of gas concentrations in real-time. These sensors leverage photonic technologies, such as waveguides and resonators, to enhance performance over traditional gas sensors. Advancements in materials and fabrication techniques could further improve their efficiency, making them invaluable for environmental monitoring, industrial safety, and healthcare diagnostics. In this review, we delved into photonic gas sensors that operate based on the principles of evanescent field absorption (EFA) and wavelength interrogation methods. These advanced sensing mechanisms allow for highly sensitive and selective gas detection, leveraging the interplay of light with gas molecules to produce precise measurements.

The simultaneous advances in artificial neural networks and photonic integration technologies have spurred extensive research in optical computing and optical neural networks (ONNs). The potential to simultaneously exploit multiple physical dimensions of time, wavelength and space give ONNs the ability to achieve computing operations with high parallelism and large-data throughput. Different photonic multiplexing techniques based on these multiple degrees of freedom have enabled ONNs with large-scale interconnectivity and linear computing functions. Here, we review the recent advances of ONNs based on different approaches to photonic multiplexing, and present our outlook on key technologies needed to further advance these photonic multiplexing/hybrid-multiplexing techniques of ONNs.

We report a micro-ring resonator with adiabatic bends, non contact waveguide heaters and small bend radius. The ring has the lowest reported off resonance loss and can support 8 wavelength division multiplexed channels at 200 GHz spacing. We measure 0.49 nm/mW tuning efficiency and 0.085 dB off resonance loss.

It is well-known that surface plasmon wave propagates along a straight line, but this common sense was broken by the artificial curved light – plasmon Airy beam. In this paper, we introduce a new class of curved surface plasmon wave - the photonic hook plasmon. It propagates along wavelength scaled curved trajectory with radius less than surface plasmon polariton wavelength, and can exist despite the strong energy dissipation at the metal surface.

The study of photonic crystals has emerged as an attractive area of research in nanoscience in the last years. In this work we study the properties of a two-dimensional photonic crystal composed of dielectric rods. The unit cell of the system is composed of six rods organized on the sites of a C6 triangular lattice. We induce a topological phase by introducing an angular perturbation ϕ in the pristine system. The topology of the system is then determined by using the so-called k.p perturbed model. Our results show that the system presents a topological and a trivial phases, depending on the sign of the angular perturbation ϕ. The topological character of the system is probed by evaluating the electromagnetic energy density and analyzing its distribution in the real space, in particular on the maximal Wyckoff points. We also find two edge modes at the interface between the trivial and topological photonic crystals, which present a pseudospin topological behavior. By applying the Bulk-Edge correspondence, we study the pseudospin edge modes and conclude that they are robust against defects, disorder and reflection. Moreover, the localization of the edge modes leads to the confinement of light and the interface behaves as a waveguide for the propagation of electromagnetic waves. Finally, we show that the two edge modes present energy flux propagating in opposite directions, which is the photonic analogue of the quantum spin Hall effect.

For W-band long-range mm-wave wireless transmission systems, nonlinearity issues resulting from photoelectric devices, optical fiber, and wireless power amplifiers can be handled by deep learning equalization algorithms. Besides, the PS technique is considered an effective measure to further increase the capacity of the modulation-constraint channel. However, since the proba-bilistic distribution of m-QAM varies with the amplitude, there have been difficulties in learning valuable information from the minority class. This limits the gain of nonlinear equalization. To overcome the imbalanced machine learning problem, we propose a novel two-lane DNN (TLD) equalizer with the random over-sampling (ROS) technique in this paper. The combination of PS at the transmitter and ROS at the receiver improves the overall performance of the W-band wireless transmission system, and our 4.6-km ROF delivery experiment verifies its effectiveness for the W-band mm-wave PS-16QAM system. Based on our proposed equalization scheme, we realize single-channel 10-Gbaud W-band PS-16QAM wireless transmission over 100 m optical fiber link and 4.6-km wireless air-free distance. The results show that compared with the typical TLD without ROS, the TLD-ROS can improve the receiver sensitivity by 1dB. Furthermore, a reduction of 45.6% in complexity is realized, and training samples can be reduced by 15.5%. Considering the actual wireless physical layer with its requirements, there is much to be gained from the joint use of deep learning and balanced data pre-processing techniques.

As a derivative of graphene, graphene oxide (GO) was initially developed by chemists to emulate some of the key properties of graphene, but it was soon recognized as a unique material in its own right, addressing an application space that is not accessible to chemical vapor deposition based materials. Over the past decade, GO has emerged as a new frontier material with tremendous advances in its material fabrication and quality control over its properties. These in turn have led to rapid progress in GO based photonics, electronics, and optoelectronics concepts and devices, evoking new science and paving the way for many technological breakthroughs with exceptional performance. Here, we review the unique fundamental characteristics of GO, its thin film fabrication methods, patterning techniques, and mechanisms for tuning its material properties. This latter capability in particular has enabled novel advanced functional photonic, electronic, and optoelectronic devices. Understanding these insights is essential for designing and tailoring GO properties for state-of-the-art applications including solar energy harvesting, energy storage, medical diagnosis, image displays, and optical communications. We conclude by discussing the open challenges and exciting opportunities of this field, together with future prospects for major technological advancements and breakthroughs.

Any photon, regardless of its origin, carries the same optical field profile. This feature and the quantum Rayleigh emissions generate temporally discrete groups of several photons in a resonant cavity incorporating one single quantum dot. A periodic stream of single photons is distorted by high-finesse optical cavities and the quantum Rayleigh spontaneous emission in a beam splitter. Groups of photons emerge from interferometric filters because of multiple internal reflections.

We demonstrate fabrication of single-mode optical waveguides on lithium niobate on insulator (LNOI) by optical patterning combined with chemo-mechanical polishing. The fabricated LNOI waveguides have a nearly symmetric mode profile of a mode field size of ~2.5 µm (full-width at half maximum). We develop a high-precision measurement approach by which the single mode waveguides are characterized to have a propagation loss of ~0.042 dB/cm.

We report fabrication of a multifunctional photonic integrated chip on lithium niobate on insulate (LNOI), which is achieved by femtosecond laser assisted chemo-mechanical polish. We demonstrate a high extinction ratio beam splitter, a 1 × 6 optical switch, and a balanced 3 × 3 interferometer on the fabricated chip by reconfiguring the microelectrode array integrated with the multifunctional photonic circuit.

Photonic sensors are innovative devices that leverage the principles of light-matter interaction to enable precise and efficient detection of various physical parameters. These sensors operate by exploiting the interaction between photons, the fundamental particles of light, and matter. The light propagates through an optical waveguide, and a portion of the electromagnetic field extends beyond the waveguide surface, forming the evanescent field. This evanescent field interacts with the surrounding medium, allowing for highly sensitive detection of changes in the refractive index or properties of nearby substances. The underlying concept involves the modulation of light properties, such as intensity, wavelength, or phase, when it interacts with a target substance or undergoes changes in the surrounding environment. The advancements in photonic sensor technology have paved the way for enhanced sensitivity, selectivity, and miniaturization, making them invaluable tools in diverse industries. The ability to harness light-matter interactions for sensing purposes not only facilitates highly sensitive measurements but also allows for non-intrusive and remote monitoring, contributing to the evolution of smart and connected systems. In this overview, the material platforms and waveguide structures are explored that can make highly sensitive photonic devices applied to gas and biosensing applications.

Optical beam splitter is used for dividing an input optical beam into several separate beams with specific power ratio. Usually, conventional beam splitters have bulky dimensions and fixed dividing ratio which significantly limit the design of new miniaturized optical devices and integrated optical circuits. We propose and investigate a novel physical concept of a miniaturized planar optical splitter/coupler with a switching element in the form of a photonic molecule (PM) pair dispersing input optical fluxes along multiple ways with variable power proportions. The structural design of the proposed splitter is based on a silicon-on-insulator (SOI) platform and composed of high-quality resonators in the form of electromagnetically coupled submicron-sized microcylinders. The control on the power division ratio and the selection of optical beam directions is realized by tuning the photonic splitter structure to the corresponding resonance of PM supermode. Compared to known analogues, the proposed design is easy to fabricate, suitable for integration into a "System-on-a-chip" platform and can dynamically change the beam power division ratio by input wave-phase manipulation.

The development of integrated, compact, and multifunctional photonic circuits is crucial to increase the capacity of all-optical signal processing for communications, data management or microsystems. Plasmonics brings compactness to numerous photonic functions, but its integration into circuits in not straightforward due to insertion losses and poor modes matching. The purpose of this article is to detail the integration strategies of plasmonic structures on dielectric waveguides, and to show through some examples the variety and the application prospect of integrated plasmonic functions.

We report the strong coupling between plasmonic surface lattice resonances (SLRs) and photonic Fabry-Pérot (F-P) resonances in a microcavity embedded with two-dimensional periodic array of metal-insulator-metal nanopillars. For such a plasmonic-photonic system, we show that the SLR can be strongly coupled to the F-P resonances of both the odd- and even orders, and that the splitting energy reaches as high as 138 meV in the visible regime. We expect that this work will provide a new scheme for strong coupling between plasmonic and photonic modes.

Femtosecond laser two-photon polymerization (TPP) technology, known for its high precision and capability to fabricate arbitrary 3D structures, has been widely applied in the production of various micro-nano optical devices, achieving significant advancements particularly in the field of photonic wire bonding (PWB) for optical interconnects. Currently, research on optimizing both the optical loss and production reliability of polymeric photonic wires is still in its early stages. One of the key challenges is that inadequate metrology methods cannot meet the demand for multiphysical measurements in practical scenarios. This study utilizes in-situ scanning electron microscopy (SEM), for the first time, to monitor the working PWBs fabricated by TPP technology at the microscale. Optical and mechanical measurements are made simultaneously to evaluate the production qualities and to study the multiphysical coupling effects of PWBs. The results reveal that photonic wires with larger local curvature radii are more prone to plastic failure, while those with smaller local curvature radii recover elastically. Furthermore, larger cross-sectional dimensions contribute dominantly to the improved mechanical robustness. The optical loss deterioration of the elastically deformed photonic wire is only temporary, which can be fully recovered when the load is removed. After further optimization based on the results of multiphysical metrology, the PWBs fabricated in this work achieve a minimum insertion loss of 0.6 dB. In this study, the multiphysical analysis of PWBs carried out by in-situ SEM metrology offers a novel perspective for optimizing the design and performance of microscale polymeric waveguides, which could potentially promote the mass production reliability of TPP technology in the field of chip-level optical interconnection.

Optical switching is an essential part of photonic integrated circuits and the focus of research at the moment. In this research, an optical switch design working on the phenomenon of the guided-mode resonances in 3D photonic crystals-based structure is reported. The optical-switching mechanism is studied in a dielectric slab-waveguide-based structure operating in the near-infrared range in a telecom window of 1.55 µm. The mechanism is investigated by interference of two signals, i.e., the data signal and the control signal. The data signal is coupled into the optical structure and filtered utilizing guided-mode resonance, whereas, the control signal is index guided in the optical structure. The amplification or de-amplification of the data signal is controlled by tuning the spectral properties of the optical sources and structural parameters of the device. The parameters are optimized first using a single-cell model with periodic boundary conditions and later in a finite 3D-FDTD model of the device. The numerical design is computed in an open-source Finite Difference Time Domain simulation platform. Optical amplification in the range of 13.75 % is achieved in the data signal with a decrease in the linewidth up to 0.0079 µm and a quality factor of 114.58. The proposed device presents great potential in the field of photonic integrated circuits, biomedical technology, and programmable photonics.

This study presents of the microsphere-based fiber-optic sensor with the ZnO ALD coating thickness of 100 nm and 200 nm for temperature measurements. Metrological properties of the sensor were investigated over the temperature range of 100°C to 300°C, with a 10°C step. The interferometric signal is used to control whether the microstructure is intact. Spectrum shift of a reflected signal is used to conclude changes in measured parameter for the sensor with a 100 nm coating, while the reflected signal intensity is an indicator during measurements executed by a sensor with a 200 nm coating. With changing temperature, the peak position or intensity of a reflected signal also changes. The R2 coefficient of the presented sensors indicates a linear fit of over 0.99 to the obtained data. The sensitivity of the sensors, investigated in this study, equals 103.5 nW/°C and 0.019 nm/°C for ZnO thickness of 200 nm and 100 nm, respectively.

We report enhanced nonlinear optics in complementary metal-oxide-semiconductor (CMOS) compatible photonic platforms through the use of layered two-dimensional (2D) graphene oxide (GO) films. We integrate GO films with silicon-on-insulator nanowires (SOI), high index doped silica glass (Hydex) and silicon nitride (SiN) waveguides and ring resonators, to demonstrate an enhanced optical nonlinearity including Kerr nonlinearity and four-wave mixing (FWM). The GO films are integrated using a large-area, transfer-free, layer-by-layer method while the film placement and size are controlled by photolithography. In SOI nanowires we observe a dramatic enhancement in both the Kerr nonlinearity and nonlinear figure of merit (FOM) due to the highly nonlinear GO films. Self-phase modulation (SPM) measurements show significant spectral broadening enhancement for SOI nanowires coated with patterned films of GO. The dependence of GO’s Kerr nonlinearity on layer number and pulse energy shows trends of the layered GO films from 2D to quasi bulk-like behavior. The nonlinear parameter of GO coated SOI nanowires is increased 16 folds, with the nonlinear FOM increasing over 20 times to FOM > 5. We also observe an improved FWM efficiency in SiN waveguides integrated with 2D layered GO films. FWM measurements for samples with different numbers of GO layers and at different pump powers are performed, achieving up to ≈7.3 dB conversion efficiency (CE) enhancement for a uniformly coated device with 1 layer of GO and ≈9.1 dB for a patterned device with 5 layers of GO. These results reveal the strong potential of GO films to improve the nonlinear optics of silicon, Hydex and SiN photonic devices.

We develop a technique for realizing lithium niobate on insulator (LNOI) waveguides of a multi-centimeter-length with a propagation loss as low as 0.027 dB/cm. Our technique relies on patterning a chromium (Cr) thin film coated on the top surface of LNOI into a hard mask with a femtosecond laser followed by the chemo-mechanical polishing for structuring the LNOI into the waveguides. The surface roughness on the waveguides is determined to be 0.452 nm with an atomic force microscope (AFM). The approach is compatible with other surface patterning technologies such as optical and electron beam lithographies or laser direct writing, enabling high-throughput manufacturing of large-scale LNOI-based photonic integrated circuits.

Wide-bandgap tin oxide (SnO₂) thin-films are frequently used as an electron-transporting layers in perovskite solar cells due to superior thermal and environmental stabilities. However, its crystallization by conventional thermal methods requires typical temperatures between 300 and 900 ◦C [1] with up-to 60 min crystallization times. These post-processing conditions severely limit the choice of substrates and reduce the large-scale manufacturing capabilities. This work describes the intense pulsed light-induced crystallization of SnO₂ thin films using only 500 μs of exposure time. Thin-film properties are investigated using both impedance spectroscopy and photoconductivity characteristic measurements. Nyquist plot analysis establishes that the process parameters have a significant impact on the electronic and ionic behaviors of the SnO2 films. Most importantly, we demonstrate that light-induced crystallization yields improved topography and excellent electrical properties through enhanced charge transfer, improved interfacial morphology and better ohmic contacts compared to thermally-annealed SnO₂ films.

Photonic circuits find applications in biomedicine, manufacturing, quantum computing and communications. Photonic waveguides are crucial components, typically having cross-sections orders of magnitude inferior compared with other photonic components (e. g. optical fibers, light sources and photodetectors). Several light coupling methods exist, consisting of either on-plane (e. g. adiabatic and end-fire coupling) or off-plane methods (e. g. grating and vertical couplers). The grating coupler is a versatile light transference technique which can be tested at wafer level, not requiring specific fiber terminations or additional optical components, like lenses, polarizers or prisms. This study focuses on fully-etched grating couplers without bottom reflector, made from hydrogenated amorphous silicon (a-Si:H), deposited over a silica substrate. Different coupler designs were tested, of these we highlight two: superimposition of two lithographic masks with different periods and an offset between them to create a random distribution and a technique based on the quadratic refractive index variation along the device’s length. Results were obtained by 2D-FDTD simulation. The designed grating couplers achieve coupling efficiencies for the TE-like mode over -8 dB (mask overlap) and -3 dB (quadratic variation), at a wavelength of 1550 nm. The coupling scheme considers a 220 nm a-Si:H waveguide and an SMF-28 optical fiber.

Silica on Silicon is a major optical integration platform, while the emergent class of integrated Laser written circuits' platform offers additionally high customizability, and flexibility for rapid prototyping. However, the inherent waveguides' low core/cladding refractive index contrast characteristic compared to other photonic platforms in silicon or silicon nitride, sets serious limitations for on-chip efficient coupling with single photon emitters, like semiconductor nanowires with quantum dots limiting the applications in quantum computing. A new light coupling scheme proposed here overcomes this limitation providing means for light coupling >50%. The scheme is based on the incorporation of an optical microsphere between the nanowire and the waveguide, properly optimized and arranged in terms of: size, refractive index, distance of microsphere between nanowire and waveguide. Upon suitable design of the optical arrangement, the photonic nanojet emitted by the illuminated microsphere excites efficiently the guided eigenmodes of the input channel waveguide, thus launching light with high coupling efficiency. The method is tolerant in displacements, misalignments, and imperfections and is fabricationally feasible by current state of the art techniques. The proposed method enables the on-chip multiple single photon emitters' integration thus allowing the development of highly customizable and scalable quantum photonic integrated circuits for quantum computing.

Metal nanoparticles supporting plasmons are widely used to enhance electromagnetic fields, resulting in strong light-matter interactions at the nanoscale in a diverse range of applications. Recently, it has been shown that when metal nanorods are periodically arranged with proper lattice periods, surface lattice resonances (SLRs) can be excited and near fields can be greatly enhanced over extended volumes. In this work, we report significant near field enhancement over even larger volumes by placing the metal nanorod array within a Fabry-Pérot (F-P) microcavity. Results show that taking advantage of strong coupling between the SLR and the photonic F-P resonances, the electric field intensity of the bonding split mode can be enhanced by up to 1935 times, which is about three times of the enhancement of the SLR, and the greatly enhanced field can extend over most of the F-P microcavity. We further show that the F-P resonances of both odd and even orders can strongly couple to the SLR by varying the nanorods position from the middle of the microcavity. We expect that the proposed plasmonic-photonic coupling system will find promising applications in nanolasers, nonlinear optics and sensing.

Minimizing optical losses in resonant cavities is crucial for improving photonic device performance. This study focuses on the development of a simulation tool to analyze scattering losses in Fabry-Pérot interferometers (FPI), offering precise modeling of waveguide dynamics and contributing to accurate loss predictions across various platforms. Optical cavities often suffer from scattering losses due to surface roughness and material defects. Our approach integrates theoretical models and simulations to quantify these losses, utilizing the FPI as a model system. We identified upper and lower reflectivity thresholds, beyond which accurate measurement of losses becomes unreliable. For reflectivity below a certain threshold, measurement errors arise, while excessively high reflectivity can reduce fringe visibility and introduce detector sensitivity issues. Simulations were used to validate the model's ability to predict reflectivity and attenuation in waveguides with varying loss levels. The software’s flexibility to adjust transmission parameters for different cavity configurations enhances its utility for a broad range of photonic systems. Our study offers a novel methodology for optical loss analysis, with practical applications in optimizing photonic devices. By providing a reliable tool for precise loss measurement, this work supports advancements in optical technologies, enabling the design of more efficient, high-performance devices across various applications.

In this work, a numerical study on the loop-terminated Mach-Zehnder interferometer (LT-MZI) structure for CO2 gas sensing application is carried out via the finite element method. The sensing arm is covered with a polyhexamethylene biguanide (PHMB) polymer which is highly receptive to CO2 gas. The refractive index of the host material decreases due to the absorption of the CO2 gas resulting in a shift in the interference pattern of the LT-MZI structure. As a result, a redshift in the wavelength is observed in the transmission spectrum of the device. The sensitivity of the device is estimated at 7.63 pm/ppm, 34.46 pm/ppm and 74.78 pm/ppm for the sensing arm length of 5 µm, 10 µm, and 15 µm, respectively. The sensitivity can be further enhanced, however at the cost of the bigger footprint of the device. Utilizing the innovative sensor design, a comprehensive range of CO2 gas concentrations spanning from 0 to 524 ppm is successfully detected. This compact and highly sensitive device serves as a vital tool for monitoring indoor CO2 levels, fostering a healthier breathing environment for all occupants.

Scintillators play a key role in the detection chain of several applications which rely on the use of ionizing radiation, and it is often mandatory to extract and detect the generated scintillation light as efficiently as possible. In positron emission tomography (PET), for example, both energy resolution and coincidence resolving time, two of the key detection parameters, depend strongly on the total amount of light which reaches the photodetector surface as well as its spatial and temporal distribution. Typical inorganic scintillators do however feature a high index of refraction, which impacts light extraction efficiency in a negative way. Furthermore, several applications such as preclinical PET rely on pixelated scintillators with small pitch. In this case, applying reflectors on the crystal pixel surface, as done conventionally, can have a dramatic impact of the packing fraction and thus the overall system sensitivity. This paper presents a study on light extraction techniques, as well as combinations thereof, for two of the most used inorganic scintillators (LYSO and BGO). Novel approaches, employing distributed Bragg reflectors (DBRs), metal coatings, and a modified Photonic Crystal (PhC) structure, are described in detail and compared with commonly used techniques. The nanostructure of the PhC is surrounded by a hybrid organic/inorganic silica sol-gel buffer layer which ensures robustness while maintaining its performance unchanged. We observed in particular a maximum light gain of about 41% on light extraction and 21% on energy resolution for BGO, a scintillator which has gained interest in the recent past due to its prompt Cherenkov component and lower cost.

Noninvasive and portable diagnoses via angle-resolved coherent spectral data are presented. ACTIRS (Angle- resolved coherent tomographic IR spectroscopy) through angle-coherent return spectra from photonic quantum ring laser of whispering gallery modes, which is not photocurrent-converted after the cortical, vascular or muscular diffuse paths, can be a new method for brain/heart studies. Also it will be eligible for frequent do-it-yourself diagnoses of breast cancer before hospital visits. The unique angle-coherent multi-spectra will eventually lead to study ionic or protein contents of cranial, arterial or lactiferous ducts that have been obtained only from uncomfortable biopsy, NMR, CT or mammography. The spectral data can be spatially or temporally improved and correlated for extracting more meaningful diagnostic conclusions

The presence of the quantum Rayleigh scattering, or spontaneous emission, inside a dielectric medium such as a beam splitter or an interferometric filter, prevents a single-photon from propagating in a straight-line. Modelling a beam splitter by means of a unitary transformation is physically meaningless because of the loss of photons. Additional missing elements from the conventional theory are: 1) the quantum Rayleigh stimulated emission which can form groups of photons of the same frequencies, and 2) the unavoidable parametric amplification of single-photons in the original parametric crystal. An interference filter disturbs, through multiple internal reflections, the original stream of single-photons, thereby confirming the existence of groups of photons being spread out to lengthen the coherence time. The approach of modelling individual, single measurements with statistical ensemble probability amplitudes leads to the counterintuitive explanations of the experimental outcomes and should be replaced with pure states describing instantaneous measurements which are afterwards averaged.

The article continues the author's publications about the matrix-tensor study of universal rules of stochastic (probabilistic) organization of long single-stranded DNA sequences in eukaryotic and prokaryotic genomes. The author reveals that corresponding matrices of probabilities of n-plets in n-textual representations of each genomic DNA are numerically interrelated each with other in such algebraic form, which has analogies with formalisms of the known tensor-matrix theory of digital antenna arrays. These arrays combine many separate antennas into a single coordinated ensemble with unique emergent properties, due to which antenna arrays are widely used in devices of medicine, astrophysics, avionics, etc. The noted analogies allow putting forward the author's hypothesis that the stochastic organization of genomic DNAs is connected with bio-antenna arrays. From the point of view of this hypothesis, many known facts about using principles of antenna arrays in inherited physiological phenomena are collected in a single grouping with genomic DNAs. This new topic about the biological meaning of profitable properties of antenna arrays includes problems of biological evolution, the origin of the genetic code, regenerative medicine, and the development of algebraic biology. These issues are discussed jointly with the author's results of quantum information analysis of stochastic features of genomic DNAs.

Photonic integrated circuits (PIC) devices are impacted by fabrication tolerances and therefore, prior knowledge of such variation could improve the PIC fabrication process and overall yield. This paper presents a method for predicting the fabrication impacts on a telecommunication optical digital to analog converter (oDAC) based pulse amplitude modulator level four (PAM-4) transmitter. Our findings allow us to estimate the production yield in fabrication scenario using symbol error rate (SER) benchmark.

We describe a machine learning (ML) approach to process the signals collected from Covid-19 optical-based detector. Multilayer Perceptron (MLP) and Support Vector Machine (SVM) were used to process both raw data and feature engineering data, and high performances for qualitative detection of the SARS-CoV-2 virus with concentration down to 1 TCID50/ml has been achieved. Valid detection experiments contain 486 negative and 108 positive samples; and control experiments, in which biosensors without antibody functionalization were used to detect SARS-CoV-2, contains 36 negative samples and 732 positive samples. Data distribution patterns of the valid and control detection dataset, based on T-distributed Stochastic Neighbor Embedding (t-SNE), was used to study the distinguishability between positive and negative samples, and explain the ML prediction performances. This work demonstrates that ML can be a generalized effective approach to process signals and dataset of biosensors dependent on resonant modes as biosensing mechanism.

Three physical elements are missing from the conventional formalism of quantum photonics: 1) the quantum Rayleigh spontaneous and stimulated emissions; 2) the unavoidable parametric amplification; and 3) the mixed time-frequency spectral structure of a photonic field which specifies its duration or spatial extent. As a single photon enters a dielectric medium, the quantum Rayleigh scattering prevents it from propagating in a straight-line, thereby destroying any possible entanglement. A pure dynamic and coherent state composed of two consecutive number states, delivers the correct expectation values for the number of photons carried by a photonic wave front, its complex optical field, and phase quadratures. The intrinsic longitudinal and lateral field profiles associated with a group of photons for any instantaneous number of photons are independent of the source. These photonic properties enable a step-by-step analysis of the correlation functions characterizing counting of coincident numbers of photons or intensities with unity visibility interference, spanning the classical and quantum optic regimes

Aquaculture is expected to play a vital role in solving the challenge of sustainably providing the growing world population with healthy and nutritious food. Pathogen outbreaks are a major risk for the sector, so early detection and a timely response are crucial. This can be enabled by monitoring of pathogen levels in aquaculture facilities. This paper describes a photonic biosensing platform based on silicon nitride waveguide technology with integrated active components, which could be used for such applications. Compared to the state of the art, the current system presents improvements in terms of miniaturization of the Photonic Integrated Circuit (PIC), and the development of wafer level processes for hybrid integration of active components and for material-selective chemical and biological surface modification. Furthermore, scalable processes for integrating the PIC in a microfluidic cartridge have been developed, as well as a prototype desktop readout instrument. Three bacterial aquaculture pathogens (Aeromonas salmonicida, Vagococcus salmoninarum, and Yersinia ruckeri) were selected for assay development. DNA biomarkers were identified, corresponding primer-probe sets designed, and qPCR assays developed. The biomarker for Aeromonas was also detected using the hybrid PIC platform. This is the first successful demonstration of biosensing on the hybrid PIC platform.

Thanks to advanced semiconductor microfabrication technology, chip-scale integration and miniaturization of lab-on-a-chip components, silicon-based optical biosensors have made significant progress for the purpose of point-of-care diagnosis. In this review, we provide an overview of the state-of-the-art in evanescent field biosensing technologies including interferometer, microcavity, photonic crystal, and Bragg grating waveguide-based sensors. Their sensing mechanisms and sensor performances, as well as real biomarkers for label-free detection, are exhibited and compared. We also review the development of chip-level integration for lab-on-a-chip photonic sensing platforms, which consist of the optical sensing device, flow delivery system, optical input and readout equipment. At last, some advanced system-level CMOS-chip packaging examples are presented, indicating the commercialization potential for the low cost, high yield, portable biosensing platform leveraging CMOS processes.

Backward electromagnetic waves are extraordinary waves with contra-directed phase velocity and energy flux. Unusual properties of the coherent nonlinear optical coupling of the phase-matched ordinary and backward electromagnetic waves with contra-directed energy fluxes are described which enable greatly-enhanced frequency and propagation direction conversion, parametrical amplification, as well as control of shape of the light pulses. Extraordinary transient processes that emerge in such metamaterials in pulsed regimes are described. The results of the numerical simulation of particular plasmonic metamaterials with hyperbolic dispersion are presented, which prove the possibility to match phases of such coupled guided ordinary and backward electromagnetic waves. Particular properties of the outlined processes in the proposed metamaterial are demonstrated through numerical simulations. Potential applications include ultra-miniature amplifiers, frequency changing reflectors, modulators, pulse shapers, and remotely actuated sensors.