Acquisition of real-time hydraulic data is an essential component for flood forecasting. However, we frequently face difficulties in obtaining discharge data using classical contact methods during high magnitude floods and for systems experiencing rapid hydro-geomorphological adjustment. Therefore, we developed low-cost, non-contact sensors and platforms that are designed to overcome these difficulties. These advances enable flood flow properties to be monitored at multiple locations across a river catchment, at low-cost, and communicated in near real-time by using an image velocimetry method. This is an optics-based approach for stream flow measurement using commercially available near-infrared digital cameras to acquire video footage in full HD (30fps). Video footage is then subjected to optical flow tracking techniques based on cross-correlation, and feature-based tracking, enabling the displacement rates of detected features (for example natural foam, seeds, woody debris, and turbulent structures) to be computed. This manual provides step by step guidance to install an image-based gauging station. It contains the list of necessary components, the calibration process of a new camera and the assembly procedure of the system.

This is a short note on a new way to describe Haug's newly introduced maximum velocity for matter in relation to the Schwarzschild radius. This leads to a probabilistic Schwarzschild radius for elementary particles with mass smaller than the Planck mass. In addition, our maximum velocity, when linked to the Schwarzschild radius, seems to predict that particles just at that radius cannot move. This implies that radiation from the Schwarzschild radius not can undergo velocity time dilation. Our maximum velocity of matter, therefore, seems to predict no time dilation, even in high Z quasars, as has surprisingly been observed recently.

Glacier dynamics play an important role in the mass balance of many glaciers, ice caps and ice sheets. In this study we exploit Radarsat-2 (RS-2) Wide Fine (WF) data to determine the surface speed of Svalbard glaciers in the winters of 2012/2013 and 2013/2014 using Synthetic Aperture RADAR (SAR) offset and speckle tracking. The RS-2 WF mode combines the advantages of the large spatial coverage of the Wide mode (150 x 150 km) and the high pixel resolution (9m) of the Fine mode and thus has a major potential for glacier velocity monitoring from space through offset and speckle tracking. Faster flowing glaciers (1.95 m d^-1 - 2.55 m d^-1) which are studied in detail are Nathorstbreen, Kronebreen, Kongsbreen and Monacobreen. Using our Radarsat-2 WF dataset, we compare the performance of two SAR tracking algorithms, namely the GAMMA Remote Sensing Software and a custom written MATLAB script (GRAY method) that has primarily been used in the Canadian Arctic. Both algorithms provide comparable results, especially for the faster flowing glaciers and the termini of slower tidewater glaciers. A comparison of the WF data to RS-2 Ultrafine and Wide mode data reveals the superiority of RS-2 WF data over the Wide mode data.

Abstract: Discussed is an expansion of SRT to fourth-order of space-time including any velocities and possible negative kinetic energies by real rest mass in analogy of the model amplitude of enforced damped oscillation. This paper serves an introduction to developed SRT including superluminar translating velocities without tachyons or imaginary restmass. Focused is on those parts, which develop the elaborated lorentz-transformations. Discussed are the problems of this theory.

This is the second paper in a cycle investigating the exact solution of loop equations in decaying turbulence. We perform numerical simulations of the Euler ensemble, suggested in the previous work, as a solution to the loop equations. We designed novel algorithms for simulation, which take a small amount of computer RAM so that only the CPU time grows linearly with the size of the system and its statistics. This algorithm allows us to simulate systems with billions of discontinuity points on our fractal curve, dual to the decaying turbulence. For the vorticity correlation function, we obtain \textbf{quantum fractal laws} with regime changes between universal discrete values of indexes. The traditional description of turbulence with fractal or multifractal scaling laws does not apply here. The measured conditional probabilities of fluctuating variables are smooth functions of the logarithm of scale, with statistical errors being negligible at our large number of random samples $T = 167,772,160$ with $N = 200,000,000$ points on a fractal curve. The quantum jumps arise from the analytical distribution of scaling variable $X = \frac{\cot^2(\pi p/q)}{q^2}$ where $\frac{p}{q}$ is a random fraction. This distribution is related to the totient summatory function and is a discontinuous function of $X$. In particular, the energy spectrum is a devil's staircase with tilted uneven steps with slopes between $-1$ and $-2.03$. The logarithmic derivative of energy decay $n(t)$ as a function of time is jumping down the stairs of universal levels between $1.50$ and $1.53$. The quantitative verification of this quantization would require more precise experimental data.

The issue of optimising the initial stand density (ISD) of tree plantations has high practical importance. The objective of this study was to nondestructively evaluate the influence of the initial stand density of Scots pine plantations located in the European part of the Russian Federation on wood basic density (BD), moisture content (MC), ultrasound velocity (UV), latewood content, and drilling resistance (DR). 45-year-old trees with stand densities of 500, 1000, 3000, 5000, and 10000 trees/ha were tested by a 5-cm-long core sample for gravimetric MCGM and BD, by PULSAR-2.2 for UV along the height (UVH) and through the tree trunk diameter (UVD), by the IML-RESI PD-400 tool for DR, and by GANN HT 85T for MC based on the electrical resistance method (MCERM). A significant influence of ISD was found on DBH, UVD, MCGM, and MCERM. ISD had no significant impact on BD, UVH, and DR. The wood BD ranged from 356 to 578 kg/m-3, with a mean value of 434±3.3 kg/m-3, and was restricted by the soil and environmental factors. DBH and 70% MCERM were good indicators of tree vitality. Linear correlations between DBH and MCERM (R2=0.67), DBH and MCGM (R2=0.74), DR and BD (R2=0.71), and the two-factor model MCGM=f(DBH, BD), (R2=0.76) were found.

In this paper, we consider the behavior of the local energy flow velocity of the fundamental air – core mode at the core – cladding boundary in two types of hollow – core fibers: hollow – core fibers with a negative curvature of the core boundary and single – capillary fibers with similar geometrical parameters. It is demonstrated that the behavior of both axial and radial components of the local energy velocity of the fundamental air – core mode is completely different for these two types of hollow – core fibers. The negative curvature of the core boundary leads to an alternating behavior of the radial projection of the local energy velocity and a decrease by two orders of magnitude compared to the values of this projection for a single capillary. In our opinion, this behavior of the local energy velocity of the fundamental air – core mode is caused by a periodic set of Poynting vector vortices that appear in the cladding capillary walls.

A large set of undrained compression triaxial tests was carried out on different types of cohesionless soils, from sands to silty-sands and silts. Shear wave velocity measurements were carried out alongside. These tests exhibited distinct state transitions ranging from flow liquefaction to strain softening or strain hardening. With the purpose of defining a framework to assess soil liquefaction, it was found that the ratio between the shear wave velocity (VS0) and the peak undrained deviatoric stress, qpeak, VS0/qpeak, could be accurately used to define a boundary between liquefaction and strain hardening for sands, and between strain softening and strain hardening for silty-sands and silts. Since this ratio is a function of the tested material, it was also discovered that the prediction of these boundaries could be made as a function of soil grading, namely via the coefficient of uniformity, CU. Despite not being regarded as a strong geomechanical parameter, CU is easily determined from a grain-size distribution test and it has an empirically proven correlation with critical state parameters.

The turbulent Poiseuille flow between two parallel plates is one of the simplest possible physical situations, and it has been studied intensively. In this paper, we propose a modified Prandtl-van Driest mixing length that satisfies both boundary conditions and wall damping effects. With our new formulations, we numerically solve the problem and, moreover, propose an approximate analytical solution of mean velocity. As applications of our solution, an approximate analytical friction coefficient of turbulent Poiseuille flow is proposed.

Background: Brachial-ankle pulse wave velocity (baPWV) is widely used as a marker of arterial stiffness. It has been suggested as a simple method for detecting arterial loads that can trigger left ventricular hypertrophy in the heart. Increased left ventricular hypertrophy in hypertensive patients is a predictor that will have an impact on increasing morbidity and mortality. Objective: This study aimed to evaluate the correlation between the baPWV and the left ventricular mass index (LVMI) in hypertensive patients. Methods: This cross-sectional study was conducted by collecting secondary data from hypertensive patients at the Heart Outpatient Clinic, with inclusion: aged more than 40 years old, suffering hypertension more than one year, and had baPWV and echocardiography data. Correlation between baPWV and LVMI was evaluated using the Pearson correlation test. Results: A total of 40 hypertensive patients were enrolled in this study. 60% were women. The mean age was 52.92 ± 9.50 years. Mean LVMI was 107.20 + 21.01 gram/m2. LVMI showed a significant association with age and systolic blood pressure (p=0.001 and 0.019, respectively). Mean baPWV was 1832.90 + 336.22 cm/sec. A significant association was found between baPWV and age and systolic blood pressure (p=0.000 and 0.049, respectively). There was a significant positive correlation between baPWV and LVMI (r=0.493, p=0.001); and between baPWV and Relative Wall Thickness (RWT) (r=0.404, p=0.01). Conclusion: This study shows that elevated baPWV is an indicator of increased LVMI in hypertensive patients. Examination of baPWV should be carried out routinely to detect earlier arterial stiffness as a morbidity and mortality prevention strategy in hypertensive patients.

Unification point of view, quantum cosmology must be given a priority and one should make a note that, Spin is a basic property of quantum physics and rotation is a very common experience. In this context, we have developed a quantum model of cosmology associated with Machian universe having Planck scale origin, total dark matter, light speed rotation and equality of gravitational self energy density and thermal energy density. We would like to appeal that, observed cosmic radius and age seem to be shortened by 146.3 times their actual magnitudes.

The presence of dark matter, though well established by indirect evidence is yet to be observed directly. Various dark matter detection experiments running for several years have yielded no positive results so far. In view of these negative results, we had earlier proposed alternate models by postulating a minimum gravitational field strength (minimum curvature) and also a minimum acceleration. These postulates led to the modified Newtonian dynamics and modified Newtonian gravity (MONG). The observed flat rotation curves of galaxies had also been accounted for through these postulates. Here we extend these postulates to galaxy clusters and model the dynamical velocity-distance curves for such large-scale structures. The velocity-distance curve of the Virgo cluster, plotted with this model is found to be in accordance with that observed.

As an important civil and military infrastructure, airport runway pavement is faced up with threats from cluster munitions, since it is vulnerable to projectile impact with internal explosion. Aiming at the damage assessment of island airport runway pavement under impact, this work dealt with discrete modeling of rigid projectile penetration into concrete pavement and calcareous sand subgrade multi-layer structure. First, Discrete Element Method (DEM) is introduced to model concrete and calcareous sand granular material features like cohesive fracture and strain hardening due to compression, with mesoscale constitutive laws governing the normal and shear interactions between adjacent particles. Second, sequent DEM simulations of uniaxial and triaxial compression were performed to calibrate the DEM parameters for pavement concrete as well as subgrade calcareous sand. Piror to multi-layer structure investigations, penetration into sole concrete or calcareous sand is validated in terms of projectile deceleration and depth of penetration (DOP) with relative error

This paper introduces a three-layer system, proposing a comprehensive model of granular mixture transport over a mobile sloped bed in a steady flow. This system, consisting of the bottom, contact and upper zones, provides complete, continuous sediment velocity and concentration vertical profiles. The model considers gravity’s effect on sediment transport in the bottom (dense) layer, a crucial factor often overlooked in previous studies. The induced movement in the mobile sublayer of the dense layer causes an increase in velocity at the upper boundary of this layer, significantly affecting the vertical distributions of velocity and concentration above this layer. We described the interactions between fractions and an intensive sediment mixing and sorting process in the contact layer. The proposed shear variation, with an increase in its maximum value at the bed, adds to the novelty of our approach. The data sets used for the model’s validation cover various conditions, including slopes, grain diameters, densities and grain mobility conditions, from incipient motion to a fully mobilised bed. This extensive validation process instils confidence in the theoretical description and its applicability to real-world scenarios.

This paper brings to fruition recently found \cite{migdal2023exact} exact reduction of decaying turbulence in the Navier-Stokes equation in $3 + 1$ dimensions to a Number Theory problem of finding the statistical limit of the Euler ensemble. We reformulate the Euler ensemble as a Markov chain and show the equivalence of this formulation to the \textbf{quantum} statistical theory of $N$ fermions on a ring, with an external field related to the random fractions of $\pi$. We find the solution of this system in the turbulent limit $N\to \infty, \nu \to 0$ in terms of a complex trajectory (instanton) providing a saddle point to the path integral over the density of these fermions. This results in an analytic formula for the observable correlation function of vorticity in wavevector space. This is a full solution of decaying turbulence from the first principle without approximations or fitted parameters. The energy spectrum decays as $k^{-\frac{7}{2}}$. We compute resulting integrals in \Mathematica{} and present effective index $n(t) = -t\partial_t \log E $ for the energy decay as a function of time Fig.\ref{fig::NPlot}. The asymptotic value of the effective index in energy decay $n(\infty) = \frac{5}{4}$, but the universal function $n(t)$ is neither constant nor linear.

Cement paste backfill (CPB) is an effective waste management method allowing the storage of fine process tailings into underground mined-out voids. CPB performance generally depends on the sulfur content of the tailings and the type of binder. In recent years, there has been an in-creasing trend on the use of alkali-activated slag (AAS) to improve the performance properties of CPB. This study focuses on the ultrasonic and microstructural investigation of the effect of slag fineness on the mechanical, geochemical and durability properties of CPB made up of AAS (AAS-CPB) over 360 days. In this scope, AAS-CPB samples were prepared at three different fineness (3100-4650-6300 cm2/g). Fineness of slag significantly improved the early age- and long-term strength (~2.3 fold and ~6.6 fold, respectively) of CPB. However, further increase of slag fineness may have adverse effect on CPB microstructure and strength in the long term. Ultrasonic pulse velocity monitoring displayed very high relation with the strength evolution and durability assessment of CPB. Slag fineness at a degree was seen to improve the pore structure evolution of AAS-CPB. Microstructural studies are in good agreement with the geochemical and durability behavior of AAS-CPB. Microstructural and ultrasonic findings suggest that while slag fineness enhances the mechanical properties of AAS-CPB, further increase of the fineness of slag has no additional important technical advantages.

We have found an infinite dimensional manifold of exact solutions of the Navier-Stokes loop equation for the Wilson loop in decaying Turbulence in arbitrary dimension $d >2$. This solution family is equivalent to a fractal curve in complex space $\mathbb C^d$ with random steps parametrized by $N$ Ising variables $\sigma_i=\pm 1$, in addition to a rational number $\frac{p}{q}$ and an integer winding number $r$, related by $\sum \sigma_i = q r$. This equivalence provides a \textbf{dual} theory describing a strong turbulent phase of the Navier-Stokes flow in $\mathbb R_d$ space as a random geometry in a different space, like ADS/CFT correspondence in gauge theory. From a mathematical point of view, this theory implements a stochastic solution of the unforced Navier-Stokes equations. For a theoretical physicist, this is a \textbf{quantum} statistical system with integer-valued parameters, satisfying some number theory constraints. Its long-range interaction leads to critical phenomena when its size $N \rightarrow \infty$ or its chemical potential $\mu \rightarrow 0$. The system with fixed $N$ has different asymptotics at odd and even $N\rightarrow \infty$, but the limit $\mu \rightarrow 0$ is well defined. The energy dissipation rate is analytically calculated as a function of $\mu$ using methods of number theory. It grows as $\nu/\mu^2$ in the continuum limit $\mu \rightarrow 0$, leading to anomalous dissipation at $\mu \propto \sqrt{\nu} \to 0$. The same method is used to compute all the local vorticity distribution, which has no continuum limit but is renormalizable in the sense that infinities can be absorbed into the redefinition of the parameters. The small perturbation of the fixed manifold satisfies the linear equation we solved in a general form. This perturbation decays as $t^{-\lambda}$, where the anomalous dimensions $\lambda$ satisfy the spectral equation \eqref{spectralEq}. The spectrum becomes a continuum in the statistical limit $N \to \infty$, presumably leading to multifractal phenomena.

Ballasted railway tracks can be modelled using reduced/simplified models composed of several layers of discrete components. This paper deals with the two-layer model, which is very popular due to its computational efficiency. In order to provide some recommendations for track design, it is necessary to identify which set of parameters leads to some irregular/unexpected behavior. Such irregularity is investigated at three levels, such as: (i) critical velocity of moving constant force; (ii) instability of a single moving mass; (iii) instability of two moving masses. All results are presented in dimensionless form to cover a wide range of real parameters. Irregular cases are identified by sets of parameters leading to them and then general conclusions are drawn. Regarding the method, all results are obtained analytically or semianalytically, where “semi” refers to solving the roots of a given polynomial by predefined numerical procedures in symbolic software. No numerical integration is involved in all results presented. This means that the results are highly accurate and refer to exact values, so any kind of parametric or sensitivity analyses is readily possible.

A rigid protruding surface, agitator and vortex generator often dissipate more energy than to produce a satisfied turbulence production. In contrast, a passively-oscillating flexible protruding surface has the ability in generating greater turbulence level. In the current study, a circular finite cylinder (cantilever) was used as the geometry of the rigid and protruding surface. They were varied through the aspect ratio (AR) and materials. Also, a local Reynolds number within the subcritical flow range (102<ReD<105) was considered. The results from the rigid protruding surface (finite cylinder) is served as a validation to the published results and benchmark to the improve-ment of the turbulence generated by the flexible protruding surface. It was mentioned in the pre-vious work that the increment of turbulence production by the flexible cylinder is speculated to be oscillation, this work investigates the validity of the speculation through manipulating the struc-tural stiffness of the flexible cylinder by employing different materials. The results have further demonstrated that the flexible cylinder is capable of generating a greater turbulence through the examination of turbulence intensity, turbulence production term and Reynolds stress. All the flex-ible cylinders that oscillate show increment in turbulence production but at a different percentage. The cylinders studied in this work ranged from the least structural stiffness (EVA), moderate (al-uminium) to the highest structural stiffness (carbon steel). Through studying the normalized am-plitude responses graph of the flexible cylinder, it is identified that the oscillating motion does in-deed contribute to increment. A further investigation into the results, it is found that the factor which governs the increment is the structural velocity instead of just oscillating motion alone.

The present paper contains data on the density (ρ), sound velocity (u), specific heat capacity (c_p ) of the mixture of N,N-dimethylformamide + 1-butanol (DMF + BuOH) determined in the entire concentration range of solution and in the temperature range: (293.15–318.15) K. The analysis of thermodynamic functions such as isobaric molar expansion, isentropic and isothermal molar compression, isobaric and isochoric molar heat capacity, as well as their excess functions (〖 E〗_(p,m)^E,〖 K〗_(S,m)^E,〖 K〗_(T,m)^E,〖 C〗_"p,m" ^E,〖 C〗_"V,m" ^E) and also V_m^E was undertaken. The analysis of changes in the physicochemical quantities was based on consideration of the system in an aspect of intermolecular interactions with resulting changes in the mixture structure. The results available in the literature are confusing during the analysis and became the reason for our decision to thoroughly examine the system. What is more, for a system whose components are widely used, there is no information in the literature regarding the heat capacity of the tested mixture, which was also achieved and presented in this publication. The conclusions drawn from so many data allow us to approximate and understand the changes that occur in the structure of the system due to repeatability and consistency of the obtained results

Detailed flow distributions in vascular systems are the key to identifying hemodynamic risk factors for the development and progression of vascular diseases. Although computational fluid dynamics (CFD) has been widely used in bioengineering research on hemodynamics predictions, not only are high-fidelity CFD simulations time-consuming and computing-expensive, but also not friendly to clinical applications due to the difficulty of comprehensive numerical calculations. Machine learning (ML) algorithums to estimate the flow field in vascular systems based on the angiographic images of the blood flow using existed diagnostic tools are emerging as a new pathway to facilitate the mapping of hemodynamics. In present work, the dye injection in a water flow was simulated as an analogy of the contrast perfusion in blood flow using CFD. In the simulation, the light passes through the flow field and generates projective images, as an analogy of X-ray imaging. The simulations provide both the ground truth velocity field and the projective images of the flow with dye patterns. A rough velocity field was estimated using the optical flow method (OFM) based on projective images. ML algorithums are then trained using the ground truth CFD data and the OFM velocity estimation as the input. Finally, the interpretable (logistic regression) and deep (neural networks, convolutional neural networks, long short term memory) machine learning models are validated by using parallel in vitro experiments on the same flow setup. The validation results showed that the employed ML model significantly reduced the error rate from 53.5% to 2.5% in average for the v-velocity estimation.

The material flow dynamic and velocity distribution on the melted domain surface play a crucial role on the joint quality and formation of welding defects. In this study, authors investigated the effects of the low and high currents of plasma arc welding on the material flow and thermodynamics of molten pool and its relationship to the welding defects. The high-speed video camera (HSVC) was used to observe the convection of the melted domain and welded-joint appearance. Furthermore, to consider the Marangoni force activation, the temperature on the melted domain was measured by a thermal HSVC. The results revealed that the velocity distribution on the weld surface was higher than that inside the molten weld pool due to the difference of the massive density between the air and the steel. Moreover, in the case of low welding current (80A) the convection speed of molten was faster than that of the high welding current case (160A) owing to the difference of main driving forces direction and strength, which leading to undercut and humping defects on the weld surface and excessive convex (burn-through) defect at the bottom weld side, respectively. The medium welding current (120A) had two convection patterns with the main flow in backward direction, which resulted in better welding quality without defect. The interaction between the shear force and Marangoni force played a solid state on the convection and heat transportation processes in the plasma arc welding process.

Specifically this work is based on the concept of ‘dark energy’ as a phenomenal effect of expansion through which a theoretical value of Hubble’s constant has been introduced. It is a constant that is based on a postulate that the square root of ratio of the Siva’s constant ‘K’ and Hubble’s constant ‘H’ is exactly equal to the diameter of the neutral hydrogen atom. That is the, exact theoretical value of Hubble’s constant. This is always constant .However, space-time conversions and the changes in the velocity of light will affect the distance and velocity in Hubble’s equation. Deviation factors in velocity, distance and the Hubble’s constant have been calculated separately which are affected by change of velocity of light with expansion of space time. The observations are related to red shift. So the change factor in terms of Hubble’s constant has been calculated with respect to red shift. Thus a factor which affects the theoretical Hubble’s constant has been calculated to find the exact value of Hubble’s constant that satisfies the experimental results. The present theoretical value of Hubble’s constant has been calculated. The experimental results by plank, ACT (Atacama Cosmology Telescope), WMAP (Wilkinson Microwave Anisotropy Probe) etc. experiments are at par with the theoretical result. Thus the ontology of space time introduced in this theoretical work supposed to be correct and leads to a new theory of origin of universe for which a brief description has been provided.

We present in this work a method for estimation of plasma bubble mean zonal drift velocities using keograms generated from images of the OI 6300.0 nm nightglow emission collected from an equatorial station -- Cariri (7.4$^\circ$S, 36.5$^\circ$W), and a mid-latitude station -- Cachoeira Paulista (22.7$^\circ$S, 45$^\circ$W), both in the Brazilian sector. The mean zonal drift velocities were estimated for 239 events recorded from 2000 to 2003 in Cariri, and for 56 events recorded over Cachoeira Paulista from 1998 to 2000. It was found that plasma bubble zonal drift velocities are smaller ($\sim$60 ms$^{-1}$) for events occurring later in the night compared to those occurring earlier ($\sim$150 ms$^{-1}$). The decreasing rate of the zonal drift velocity is of $\sim$10 ms$^{-1}$/h. We have also found that, in general, bubble events appearing first in the west-most region of the keogram are faster than those appearing first in the east-most region of the keograms. Larger zonal drift velocities occur from 19 LT to 23 LT in a longitude range from 37$^\circ$ to 33$^\circ$. The method of velocity estimation using keograms compares favorably against the mosaic method developed by \cite{Arruda:2005}, but the standard deviation of the residuals for the zonal drift velocities from the two methods is $\sim$15 ms$^{-1}$

Electric and/or magnetic fields are generated by stationary charges, uniformly moving charges and accelerating charges. These field components are described in the literature as static fields, velocity fields (or generalized Coulomb field) and radiation fields (or acceleration fields), respectively. In the literature, the electromagnetic fields generated by lightning return strokes are presented using the field components associated with short dipoles and in this description the one to one association of the electromagnetic field terms with the physical process that gives rise to them is lost. In this paper, we will derive expressions for the electromagnetic fields using field equations associated with accelerating (and moving) charges and separate the resulting fields into static, velocity and radiation fields. The results illustrates how the radiation fields emanating from the lightning channel give rise to field terms varying as inverse of distance and distance squired, the velocity fields generating field terms varying as inverse of distance squired and the static fields generating fields components varying as inverse of distance squired and distance cube. These field components depend explicitly on the speed of propagation of the current pulse. However, the total field does not depend explicitly on the speed of propagation of the current pulse. It is shown that these field components can be combined to generate the field components pertinent to the dipole technique. However, in this conversion process the connection of the field components to the physical process taking place at the source that generate these fields (i.e. static charges, uniformly moving charges and accelerating charges) is lost.

A forecasting scheme of the thermal updraft velocity based on a theoretical model and data collected from flights records at gliding competitions, is presented. The forecasting scheme was based on the hypothesis that there is linear relationship between the overheat function at ground surface and the temperature difference between soil and air. The proportionality factor of this relationship was determined experimentally using observations recorded during gliding flights. The results showed that based on this simple scheme forecasting thermal convection is possible at any geographical location.

We proposed in this work the introduction of a new vision of stochastic processes through geometry induced by dilation. The dilation matrices of a given process are obtained by a composition of rotation matrices built in with respect to partial correlation coefficients. Particularly interesting is the fact that the obtention of dilation matrices is regardless of the stationarity of the underlying process. When the process is stationary, only one dilation matrix is obtained and it corresponds therefore to Naimark dilation. When the process is nonstationary, a set of dilation matrices is obtained. They correspond to Kolmogorov decomposition. In this work, the nonstationary class of periodically correlated processes was of interest. The underlying periodicity of correlation coefficients is then transmitted to the set of dilation matrices. Because this set lives on the Lie group of rotation matrices, we can see them as points of a closed curve on the Lie group. Geometrical aspects can then be investigated through the shape of the obtained curves, and to give a complete insight into the space of curves, a metric and the derived geodesic equations are provided. The general results are adapted to the more specific case where the base manifold is the Lie group of rotation matrices, and because the metric in the space of curve naturally extends to the space of shapes, this enables a comparison between curves’ shapes and allows then the classification of processes’ measure.

This paper studied the nonlinear vibrations of top tensioned cantilevered pipes conveying pressurized steady two-phase flow under thermal loading. The coupled axial and transverse governing partial differential equations of motion of the system were derived based on Hamilton’s mechanics with the centreline assumed to be extensible. Multiple scale perturbation method was used to resolve the governing equations, which resulted to an analytical approach for assessing the natural frequency, mode shape and the nonlinear coupled axial and transverse steady state response of the pipe. The analytical assessment reveals that at some frequencies the system is uncoupled, while at some frequencies a 1:2 coupling exists between the axial and the transverse frequencies of the pipe. Nonlinear frequencies versus the amplitude displacement of the cantilever pipe conveying two-phase flow at super critical mixture velocity for the uncoupled scenario exhibit a nonlinear hardening behaviour, an increment in the void fractions of the two-phase flow resulted to a reduction in the pipe’s transverse vibration frequencies and the coupled amplitude of the system. However, increasing the temperature difference, pressure and the presence of top tension were observed to increase the pipe’s transverse vibration frequencies without a significant change in the coupled amplitude of the system.

The aims of the study were to analyze the relationship between the Mediterranean diet (MD) and arterial stiffness and metabolic syndrome (MetS) and its components in individuals aged over 65, overall and by sex. Subjects were people over 65 years of age with a full record of all variables analyzed from the EVA, MARK and EVIDENT studies. Data from 1,280 subjects with a mean age of 69.52±3.58 years (57.5% men) were analyzed. MD was recorded with the validated 14-item MEDAS questionnaire used in the PREDIMED study. MetS was defined following the guidelines of the joint scientific statement from the Programa Nacional de Educación sobre el Colesterol III. Arterial stiffness was assessed with the VaSera VS-1500® device by measuring the cardio-ankle vascular index (CAVI) and the brachial-ankle pulse wave velocity (baPWV). Results: The mean MEDAS score was 6.00 ± 1.90, (5.92 ± 1.92 in men, 6.11 ± 1.88 in women; p = 0.036). The mean CAVI value was 9.30 ± 1.11 (9.49 ± 1.05 men, 9.03 ± 1.13 women; p = &lt;0.001). The mean baPWV value was 15.82 ± 2.56 (15.75 ± 2.46 men, 15.92 ± 2.68 women; p = &lt;0.001). MetS was found in 51% (49% men, 54% women; p = 0.036). Subjects with MetS had lower MD adherence and higher arterial stiffness values than subjects without MetS. Overall, we found a negative association of MD score with the number of MetS components (β = -0.168), with glycemia (β = -0.007), triglycerides (β = -0.003), waist circumference (β = -0.018), CAVI (β = -0.196) and baPWV (β = -0.065), and a positive association with HDL cholesterol (β = 0.013). By sex, associations followed the same direction but without reaching statistical significance with blood glucose and triglycerides in women and with HDL cholesterol and waist circumference in men. Conclusion: Results indicate that greater adherence to the Mediterranean diet decreases arterial stiffness and the percentage of subjects with MetS, although results differed in the association with MetS components by sex.

This work presents a heat transfer and boiling model that computes the evolution of the temperature field in a representative steel workpiece quenched from 850 or 930°C by immersion in water flowing at average velocities of 0.2 or 0.6 m/s, respectively. Under these conditions, all three boiling regimes were present during cooling: stable vapor film, nucleate boiling, and single-phase convection. The model was based on the numerical solution of the heat conduction equation coupled to the solution of the energy and momentum equations for water. The mixture phase approach was adopted using the Lee model to compute the rates of water evaporation-condensation. Heat flux at the wall was calculated for all regimes using a single semi-mechanistic model. Therefore, evolution of boiling regimes at every position on the wall surface was automatically determined. Predictions were validated using laboratory results, namely: a) Videorecording the upward motion of the wetting front along the workpiece wall surface, and b) cooling curves obtained with embedded thermocouples in the steel probe. Wall heat flux calculations were used to determine the importance of the simultaneous presence of all three boiling regimes on the heat flux distribution. It was found that this simultaneous presence leads to high heat flux variations that should be avoided in production lines.

The Stepped Frequency Waveform (SFW) is commonly employed in radar technology to synthesize wideband signals through the aggregation of narrow-band pulses, thereby achieving high-resolution range profiles without the need to increase the radar's instantaneous bandwidth. However, the inherent large time-bandwidth product of SFW introduces substantial ranging errors and energy dispersion, which significantly hinders its efficacy in detecting high-speed objects. This paper introduces a pioneering velocity estimation technique utilizing the fractional Fourier transform (FrFT) to address these limitations. Leveraging the characteristic of the Doppler signal from a moving target, which manifests as a chirp signal with a rate proportional to the target's velocity, the FrFT is utilized for precise velocity estimation. Subsequent to this, velocity compensation is applied using the deduced metrics, followed by the application of the inverse fast Fourier transform (iFFT) to pinpoint the target's exact location. To optimize the computational efficiency of determining the FrFT's optimal order, we propose an iterative algorithm founded on the golden section search method. The effectiveness of the proposed approach is verified by simulation data, and the results demonstrate that the proposed approach can accurately estimate the velocity and the range of the high-speed targets with a relatively low computational complexity.

Temporary streams are a key component of the hydrological cycle in arid and semi-arid regions, but their flow is highly variable and difficult to measure. In this paper, we present a novel approach that could be used to assess the flow of temporary streams and characterize their environmental status. Specifically, we apply the Image Velocimetry method to estimate surface velocity in temporary streams using unmanned aerial vehicles (UAVs) equipped with optical sensors (IV-UAV method). The IV-UAV method enables the easy, safe and quick estimation of the velocity on the water’s surface. This method was applied in different temporary streams in Lesvos Island, Greece. The produced results show that the IV-UAV can be implemented at low discharges, at temporary streams and at small streams. However, there were many occasions that measurements were unable due to various reasons such as dense vegetation or archaeological sites. Despite of this, the proposed methodology could be incorporated in optical protocols which are used to assess the environmental status of temporary streams of Mediterranean conditions. Finally, this would become a valuable tool for understanding the dynamics of these eco-systems and monitoring changes over time.

The determination of crack propagation velocities can provide valuable information for a better understanding of damage processes of concrete. The spatio-temporal analysis of crack patterns developing at a speed of several hundred meters per second is a rather challenging task. In the paper, a photogrammetric procedure for the determination of crack propagation velocities in concrete specimens using high-speed camera image sequences is presented. A cascaded image sequence processing which starts with the computation of displacement vector fields for a dense pattern of points on the specimen’s surface between consecutive time steps of the image sequence chain has been developed. These surface points are triangulated into a mesh, and as representations of cracks, discontinuities in the displacement vector fields are found by a deformation analysis applied to all triangles of the mesh. Connected components of the deformed triangles are computed using region-growing techniques. Then, the crack tips are determined using principal component analysis. The tips are tracked in the image sequence and the velocities between the time stamps of the images are derived. A major advantage of this method as compared to established techniques is in the fact of its allowing for spatio-temporally resolved, full-field measurements rather than point-wise measurements and that information on crack width can be obtained simultaneously. To validate the experimentation, the authors processed image sequences of tests on four compact-tension specimens performed on a split-Hopkinson tension bar. The images were taken by a high-speed camera at a frame rate of 160,000 images per second. By applying to these datasets the image sequence processing procedure as developed, crack propagation velocities of about 800 m/s were determined with a precision in the order of 50 m/s.

Vegetation has a significant influence on velocity distribution and turbulent energy in a confluence channel. A laboratory measurement with ADV was used to investigate the flow through a Y-shaped confluence channel partially covered with rigid vegetation on its inner bank. In this study, the flow velocities in cases with and without vegetation were measured by the ADV in a Y-shaped confluence channel. The results clearly show that the existence of non-submerged rigid plants has changed the internal flow structure, that the velocity in the non-vegetated area is greater than in the vegetated area, and that there is a large exchange of mass and momentum between the vegetated and non-vegetated areas. The velocity on both sides is significantly reduced when vegetation is present. In the vicinity of tributaries, due to the presence of vegetation, the high-velocity area moved rapidly to the middle of the non-vegetated area, and the secondary flow phenomenon disappeared. In the mainstream, when vegetation was present, circulation disappeared, and the degree of lateral mixing decreased. The presence of vegetation caused a great change in the internal flow structure and made the flow in non-vegetated areas more intense.

The SI unit of length, the Metre, is presently defined by taking the fixed numerical value of the fundamental constant `c', the invariant speed of light in vacuum. This definition has the same physical basis as the previous definition, as the length of the path travelled by light in vacuum during a time interval of 1/299 792 458 of a second. With the atomic standard second defined in terms of the ground state hyperfine transition in Caesium-133, this definition is supposed to provide a universally reproducible standard of length. However, this relies on Einstein's singular postulate that the relative velocity of light in vacuum is an invariant constant that is independent of any inertial motion of the reference laboratory. I argue that the basis of the definition of the standard metre should be changed to the specific form, "the length of the path equal to the two-way propagation of light in vacuum during a time interval of 1/299 792 458 of a second", to be compatible and consistent with the fact that it is only the two-way relative velocity that is consistent with being an invariant. The null result in the Michelson-Morley two-way experiment, and in all such experiments to date, is consistent with a Galilean one-way propagation of light (relative velocity $c'=c\pm v$) as well as an invariant relative velocity of light. All practical methods and protocols related to the implementation of length standard involve also a two-way propagation, not conforming to the present definition. Besides, this redefinition is absolutely necessary because the relative velocity of light in one-way propagation is indeed Galilean, and not an invariant, as proved here in multiple ways including a direct experiment.

Abstract：Ballast pick-up velocity is a crucial parameter in the design of a slurry system in excavating devices, it influences transportation stability, safety, and economy of the system. In this study, a vertical pipe hydraulic experiment with different ballast sizes under water condition was conducted to investigate the ballast pick-up velocity in the shield slurry system. Thereafter, the coupling method of computational fluid dynamics and the discrete element method (CFD-DEM) was employed to establish a numerical model of the ballast pick-up velocity in the shield slurry system, and its applicability was verified by comparing the experiment results. Additionally, the ballast pick-up process under actual working conditions was studied, and the influence of ballast size and concentration on pick-up velocity was investigated. Overall, the primary findings of the study are as follows: 1) The numerical method can be applied to predict both the single ballast and ballast group pick-up velocity. 2) The pick-up process of the ballast group can be divided into four stages. 3) The conveying velocity of the ballast should be higher than the pick-up velocity of the single ballast to facilitate smooth discharge. 4) For a certain increase in ballast concentration, the pick-up velocity tends to be stable.

It is common knowledge that estimating the height component of GNSS stations in general is much more problematic than estimating the horizontal position. Many different effects, such as tectonic signals, non-tectonic signals, atmospheric delay, noise, etc., are known to affect the height component of GNSS stations more than the horizontal component. However, the height component of GNSS stations is still poorly estimated. In this study, the height time series of 37 continuous GNSS stations covering the 2014–2019 date range is used from the Turkish National Permanent GNSS Network-Active (TUSAGA-Active). Since it is easier to interpret the effects of the height component due to its topographic features and seasonal changes being more effective than in the rest of the country, stations were chosen in the Eastern Anatolia region of Turkey. The daily coordinates of the GNSS stations were obtained as a result of the GAMIT/GLOBK software solution. By applying time series analysis to the daily coordinate values of the stations, statistically significant trends, periodic and stochastic components of the stations were determined. As a result of the analysis, the vertical velocities of the GNSS stations and the standard deviations of the vertical velocities were determined. Furthermore, when the height components of continuous GNSS stations were examined, it was seen that there were seasonal effects, and it was investigated whether the height components were related to meteorological parameters. For that, simple linear regression analysis was performed to determine how dependent the height components of the continuous GNSS stations were on meteorological parameters. As a result of the analysis, the height components of the continuous GNSS stations are dependent on meteorological parameters such as temperature, pressure, relative humidity, wind speed, and precipitation. In addition, height component time series analysis of continuous GNSS stations was performed by using Autoregressive Moving Average (ARMA) models from linear time series methods. As a result of the study, the performance of the ARMA modeling results again indicated the dependence of the height component of the continuous GNSS stations on the meteorological parameters.

Background: Objective training load indexes (TL) used in resistance training lack of physiological significance. This study aimed to provide a muscle physiology-based approach for quantifying TL in resistance exercises (RE). Methods: Following individual torque-velocity profiling, fifteen participants performed isokinetic leg extension exercise sessions at low (C1), moderate (C2), and high (C3) intensities. Systemic and local physiological responses were measured, and sessions were volume-equated according to the "volume-load" (VL) method. Results: Significant differences were found between sessions in terms of mechanical work (

Vertical jump height is a reliable measure of lower limb functionality for countermovement jumps. Motion capture systems and force platforms are considered gold standards to assess athletes’ performance during these motions, however their use in ecological settings is limited by high costs and lack of portability. This study aimed to evaluate the feasibility of low-sampling rate Inertial Measurement Units as an alternative to gold standard systems. The validity of three computational methods for IMU-based data—Numerical Double Integration, Take-Off Velocity and Flight Time—was assessed using data from 18 healthy subjects who performed five bilateral and ten unilateral countermovement jumps. Data were simultaneously collected from an IMU positioned at the L5 level, a motion capture system, and two force platforms. Comparisons revealed that the Numerical Double Integration method exhibited the highest correlation (0.87), the lowest bias (2.5 cm) compared to gold standards, and excellent reliability (0.88). Although the Take-Off Velocity and Flight Time methods demonstrated comparable performance for bilateral jumps, their accuracy in unilateral jumps was reduced. Overall, low-sampling rate IMU with Numerical Double Integration method proves to be a reliable and portable alternative for field-based CMJs assessment, warranting future investigation across diverse populations and jump modalities.

Single-confinement housing can pose welfare risks to domestic horses. This study investigated horses’ stress responses when confined to single stalls in different stable designs in a tropical savanna region to address a literature gap. In total, 23 horses were assigned to a stable with a central corridor and solid external walls (A) (N = 8), a stable with one side corridor and solid external walls (B) (N = 6) or a stable with a central corridor and no solid external walls (C) (N = 9). Air velocity, relative humidity, air temperature and noxious gases were measured inside the stables, and the heart rate and HRV of the horses were also determined. The relative humidity was lower in stable C than in stable A (p &lt; 0.05), while the air temperature was higher in stable C than in stable B (p &lt; 0.05) during the day. The airflow and ammonia levels were higher in stable C than in stables B and A (p &lt; 0.01–0.0001). Overall, horses’ HRV in stable A was lower than in those in stables B and C (p &lt; 0.05-0.01). Horses in stable A tended to experience more stress than those in other stables.

We delve into the intricate dynamics governing anisotropic fluids within the cosmological paradigm, elucidating the nuanced influence of conformal anomalies upon the stress-energy tensor. Through the presentation of a sophisticated theoretical framework, we seamlessly intertwine unconventional fluidic properties with profound cosmological considerations, thereby augmenting and refining our comprehension of the primordial universe.

In the process of use and manufacture, carbon fiber foam sandwich structures were often damaged by low-energy impact, resulting in performance degradation. Therefore, it was necessary to study the damage caused by low-speed impact of composite sandwich structures. In this paper, based on Hashin failure criterion, an equivalent finite element model of carbon fiber foam sandwich panel under low velocity impact was established. The model was used to simulate the damage of foam sandwich panel with [±45°/±45°/ (core) /±45°/±45°] ply structure under the impact energy of 10.58J, 21.17J, 31.75J and 42.34J. The simulation results of impact damage depth were compared with the experimental results. The error was less than 10%, which proved the rationality of the impact equivalent model. The model was used to predict and analyze the damage of foam sandwich panels with [±45°/ (core) /±45°], [±45°/ (0°, 90°) / (core) /±45°] and [±45°/ (0°, 90°) (core) / (0°, 90°) /±45°] ply structures under 21.17J impact energy. By comparing and analyzing the damage situation, impact force response time and impact velocity response time, the low energy impact resistance was analyzed. The results showed that increasing the number of ply structure of [±45°] can reduce the impact damage degree and improve the bearing capacity of sandwich panels.

Disparities between fold amplitude (A) and intrusion thickness (Hsill) are critical in identifying elastic or inelastic deformation in a forced fold. However, accurate measurement of these two parameters is challenging because of the limit in separability and detectability for the seismic data. In the TZ-47 exploring area from the Tarim Basin, Northwest China, we combined wireline data and 3-D seismic data, to accurately constrain the fold amplitude and total thickness of sills that inducing the roof uplift. The measurement results show that the forced fold amplitude is 155 m and the total sill thickness is 148.4 m. When using a magma density of 2.7 g/cm3, and solid rock density of 3 g/cm3, the molten magma thickness at the time of intrusion would be 153.8 m, which is almost no difference from the forced fold amplitude. Therefore, the TZ-47 fold is a pure elastic forced fold induced by emplacement of multiple sills. Measurement solely based on seismic data may not be able to detect some thin interlayers and may result in large errors.

Fluid mechanics of flow in hydrophobic, rectangular microchannels with finite aspect ratios is of paramount importance. In such microchannels, not only the effect of the side walls should be taken into account, but also the classical assumption of no-slip boundary condition (BC) is no longer valid at the solid-liquid interface. Accordingly, slip flow can occur in microchannels fabricated from surfaces with low wetting conditions, hydrophobic surfaces. Determining the interactions of liquid molecules adjacent to solid surface is still a challenging issue, and it is especially important in small scale domains. Herein, the fluid mechanics of flow through rectangular hydrophobic microchannels has been reconsidered by taking into account the general Navier-slip BCs at the solid-liquid interface. For fully developed incompressible flow in microchannels at low Reynolds number, partial differential equation (PDE) of the momentum equation simplifies to the classical Poisson equation. Accordingly, by analytically solving the Poisson equations with general Navier-slip BCs, the most general forms of velocity distributions, flow rate, friction factor and Poiseuille number have been obtained.

A number of experimental and numerical studies point out that incorporating a rotating cylinder can superiorly enhance the aerofoil performance, especially for higher velocity ratios. Yet, there have been less or no studies exploring the effects of lower velocity ratio at a higher Reynolds number. In the present study, we investigated the effects of Moving Surface Boundary-layer Control (MSBC) at lower velocity ratios (i.e. cylinder tangential velocity to free stream velocity) and higher Reynolds number on a symmetric aerofoil (e.g. NACA 0021) and an asymmetric aerofoil (e.g. NACA 23018). In particular, the aerodynamic performance with and without rotating cylinder at the leading edge of the NACA 0021 and NACA 23018 aerofoil was studied on the wind tunnel installed at Aerodynamics Laboratory. The aerofoil section was tested in the low subsonic wind tunnel, and the lift coefficient and the drag coefficient were studied for different angles of attack. The experiments were conducted for two Reynolds numbers: 200000 and 250000 corresponding to two free stream velocities: 20 m/s and 25 m/s, respectively, for six different angle of attacks (-5°, 0°, 5°, 10°, 15° and 20°). This study demonstrates that the incorporation of a leading edge rotating cylinder results in an increase of lift coefficient at lower angle of attacks (maximum around 33%) and delay in stall angle (from 10° to 15°) relative to the aerofoil without rotating cylinder.

This work investigates the use of Non-destructive tests as a tool for monitoring the structural performance of concrete structures. The investigation encompassed four phases; the first of which involved the use of destructive and non-destructive mechanisms to assess concrete strength on cube specimens. The second phase research focused on site assessment for a twin engineering theatre located at the Faculty of Engineering, University of Lagos using rebound hammer and ultrasonic pulse velocity tester. The third phase was the use of linear regression analysis model with MATLAB to establish a relationship between calibrated strength as well as ultrasonic pulse velocities with their corresponding compressive strength values on cubes and values obtained from existing structures. Results show that the root-mean squared-R² values for rebound hammer ranged between 0.275 and 0.742 while ultrasonic pulse velocity R² values were in the range of 0.649 and 0.952 for air curing and water curing systems respectively. It initially appeared that the Ultrasonic pulse velocity was more suitable for predicting concrete strength than rebound hammer but further investigations showed that the latter was adequate for early age concrete while the former was more suited for aging concrete. Hence, a combined use is recommended in this work.

The influence of climate conditions and stable design on horses housed in single stalls can have significant effects, especially in regions with tropical savannah climates. A recent study observed variations in autonomic responses in horses housed in different stable designs during the summer, but there is limited information about their conditions during the monsoon. This study investigated the stable microenvironment and autonomic regulation of horses housed in different stable archi-tectures during the monsoon in a tropical savannah environment. Twenty-two horses were allo-cated to one of three stable architectures, each with varying stable microenvironments. The findings reveal that the heart rate variability (HRV) was lower in horses in a stable with a solid external wall and lower volume-to-horse ratio compared to those in a stable with a solid external wall but a higher volume-to-horse ratio or one without a solid external wall. Additionally, the study found that stable microenvironments and HRV modulation were correlated with stable architecture. Autonomic responses differed among horses in different stable architectures, indicating that stable microen-vironments and, to some extent, volume-to-horse ratio play a role in horses’ autonomic regulation. The findings have implications for improvements in housing and welfare in tropical savannah environments.

In this paper, we investigate the accuracy and robustness of three classes of methods for solving two-phase incompressible flows on a staggered grid. Here, the unsteady two-phase flow equations are simulated by finite volumes and penalty methods using implicit and monolithic approaches (such as the augmented Lagrangian and the fully coupled methods), where all velocity components and pressure variables are solved simultaneously (as opposed to segregated methods). The interface tracking is performed with a Volume-of-Fluid (VOF) method, using the Piecewise Linear Interface Construction (PLIC) technique. The home code Fugu is used for implementing the various methods. Our target application is the simulation of two-phase flows at high density and viscosity ratios, which are known to be challenging to simulate. The resulting strategies of monolithic approaches will be proven to be considerably better suited for these two-phase cases, they also allow to use larger time step than segregated methods.

This study presents a new form of velocity distribution in laminar liquid flow in rectangular microchannels using the eigenfunction expansion technique. Darcy friction factor and Poiseuille number are also obtained analytically. Due to the symmetry of the solutions, the effects of changing the aspect ratio from 0 to ∞ are also discussed. Using finite element method (FEM), the obtained analytical results are further compared with the 3D numerical simulations for the rectangular microchannels with different range of aspect ratio and pressure gradient, and excellent agreements were found. These findings provide additional insights in interpreting the results of the pressure-driven flows in finite aspect ratio microchannels, in which very precise comparison with the macroscale theory is crucial.

With reference to Planck scale, Mach's relation and by introducing two new parameters Gamma and Beta, right from the beginning of Planck scale, we make an attempt to estimate ordinary matter density ratio, dark matter density ratio, mass, radius, temperature, age and expansion velocity (from and about the Planck mass in all directions). In analogy with currently believed cosmic acceleration, with a decreasing trend of total matter density ratio, cosmic expansion velocity can be shown to be increasing. By considering $H_0\cong 70$ km/sec/Mpc, estimated current cosmic mass, radius, total matter density, expansion velocity, temperature and age are: $4.3352\times {10}^{53}\mathrm{kg},$ $3.207\times {10}^{26}\mathrm{m},$ $3.138\times {10}^{-27}\mathrm{kg}{.\mathrm{m}}^{-3},$ $2.43c,$ $2.721\mathrm{K}$ and $19.78\mathrm{Billion}\mathrm{years}$ respectively. Point to be noted is that, with reference to Planck scale, cosmic temperature seems to be redshifted by a factor ${\left(Z_T\right)}_t\cong \sqrt{1+\ln \left(H_{pl}/H_t\right)}-1$ where $\left(H_{pl},H_t\right)$ represent Planck scale and time dependent Hubble parameters respectively. As a peculiar case, considering the equality of current Hubble parameter and current angular velocity, current cosmic rotational kinetic energy can be estimated to be 0.667 times the current critical energy. It needs further study.

Since several years there is the discussion about dark matter in the halos of galaxies. This is aconsequence of observation of halo-velocity curves in dependence of distance which don‘t fulfillthe third Kepler-law. Maybe the ansätze are wrong. Shown is a simple physical model in classicalNewton-dynamics which fits qualitative the form of observation curves. Additional Parameters canbe used to fit the curves quantitative exactly without the hypothesis of dark matter.

Casein hydrolysate improves arterial stiffness, as estimated by brachial ankle pulse wave velocity (baPWV), in untreated hypertensive subjects. Facial pigmentation is a useful biomarker for arterial stiffness. This trial evaluated whether casein hydrolysate improves facial pigmentation in association with changes in arterial stiffness. A randomized, double-blind, placebo-controlled trial was conducted in 80 non-hypertensive Japanese participants randomly assigned to receive either active tablets containing casein hydrolysate or placebo for 48 weeks. Facial pigmentation and baPWV were measured at baseline and at the end of the intervention. Other biochemical atherosclerosis-related parameters were also measured, including advanced glycation end products (AGEs). Changes in facial pigmentation showed a significant difference between the groups. Change in baPWV was significantly better in the active than in the placebo group. In contrast, no significant association was seen between changes in facial pigmentation and those in baPWV. Among other atherosclerosis-related factors, changes in advanced glycation products (AGEs) were significantly decreased in the active compared to the placebo group. Further, changes in facial pigmentation were positively correlated with those in AGEs. Changes in AGEs were independently associated with changes in facial pigmentation. Casein hydrolysate improves facial pigmentation in non-hypertensive participants. Casein hydrolysate may have beneficial effects on glycation stress.

The study of the morphology, thermal, and chemical stability of the fluorinated compounds was performed using Becke’s three-parameter hybrid functional approach with the correlation provided by Lee, Yang, and Parr and the cc-pVTZ basis set aiming to design low sensitivity, toxicity, instability, and proneness to decomposition or degradation over a short time high-energy materials. The most stable conformers of the compounds under study were selected based on their total energy. Their thermal and chemical stability was evaluated based on the binding energy per atom, chemical hardness, and softness. The oxygen-fluorine balance is assessed to evaluate the sensitivity of these new materials. The density, detonation pressure, and velocity of the selected conformers were theoretically obtained to reveal the influence of -CF3, -OCF3, and cyclic -O(CF2)nO- fragments on the energetic properties of nitroaromatics as well as their stability and resistance to shock stimuli. The results allow us to predict new multipurpose energetic materials with a good balance between power and stability. Referring to the results obtained, we recommend CF3N2, OCF3N2, C2F6N2, 1CF2N2/O2CF2N2, and 2CF4N2/O2C2F4N2 for practical usage because these compounds possess greater stability compared to tetryl and better explosive properties than TNT.

The new observations, including the fastest star, the circular velocity curve of the Milky Way and the fast galaxy bar, should imply that the mass of the center of the Milky Way is almost 10¹¹ times the mass of the Sun.

Dam breaches have catastrophic consequences, causing severe property damage, life loss, and environmental impact. The Kulekhani reservoir rockfill dam break was studied to evaluate the downstream impact. The appropriate breaching parameter of MacDonald and Langridge (1984) regression equations was selected based on the sixteen observed dam failure cases and cross-sectional geometry of the existing dam of Kulekhani. The 2D Diffusion Wave and Full Dynamic Wave Equation were applied for downstream flood assessment, Full Dynamic Wave was able to capture the physical flow phenomena like river bend effects resulting in higher flow velocity at the outer bend, and formation of eddies considering losses. The application of a Full Dynamic Equation was found to be appropriate for rapidly varying unsteady flow considering steep slopes, and sudden changes in channel geometry. Flood mapping of water depth, flow velocity, flood intensity, and arrival time were carried out for flood hazard assessment classified by the American Society of Civil Engineers (ASCE). Flow depth and extension of the flow area were compared to identify the affected area, higher flow depth and larger extension were observed using a Full Dynamic Wave Equation as a result of less flow velocity considering the losses. Almost 17 minutes of the arrival time of peak difference at the Bagmati River confluence was evaluated between the models which plays an important role in decision-making for selection of the flood model. Flood mitigation with river diversion works through a hydraulic measure of Levee was suggested to protect the highly affected households of Ranche, Nagmar, Khanikhet, and Debaltar towns. Most of the household was found to be safe after the construction of the Levee except for eleven houses that lie along the river below flood elevation of 1269.6 m.a.s.l. This signifies the importance of room for the rivers and the human settlement near the river might be life-threatening.

(1) Background: Sensing of critical events or flow signatures in nature often presents itself as a coupled interaction between a fluid and arrays of slender flexible beams, such a wind-hairs or whiskers. It is hypothesized that important information is gained in highly noisy environments by the inter-correlation within the array. (2) Methods: The present study uses a model sea lion head with artificial whiskers in the form of slender beams (optical fibres), which are subjected to a mean flow with overlaid turbulent structures generated in the wake of a cylinder. Motion tracking of the array of fibres is used to analyse the correlation of the bending deformations of pairs of fibres. (3) Results: Cross-correlation of the bending signal from tandem pairs of whiskers proves that the detection of vortices and their passage along the animals head is possible even in noisy environments. The underlying pattern, during passage of a vortex core, is a jerk-like response of the whiskers, which can be found at later arrival-times in similar form in the downstream whisker's response. (4) Conclusion: Coherent vortical structures can be detected from cross-correlation of pairs of cantilever-beam like sensors even in highly turbulent flows. Such vortices carry important information within the environment, e.g. the underlying convection velocity. More importantly in nature, these vortices are characteristic elementary signals left by prey and predators. The present work can help to further develop flow, or critical event, sensory systems which can overcome high noise levels due to the proposed correlation principle.

This work presents emission line flux and kinematic structure mapping based on IFU data of the planetary nebulae Abell 30 (A30). The IFU has a field of view (FoV) of 16" x 12.3" and was used to partially cover knots J1 and J2, and completely cover knots J3 and J4 of A30. Our emission line flux map shows recombination species C II, C III, He I, O II as well as forbidden line species [O III], [Ne III] and [Ne IV] of high excitation level are all distributed in different parts of the knots. The kinematic structure shows considerable variation in both the velocities and spatial locations of these knots with positive and negative velocity excursions from the systematic value. Forbidden line species [O III], [Ne III] are distributed in both knots J3 and J4 but they are travelling at different speeds in opposite directions. Despite variation in distribution of the species, the velocities of [Ne IV] and [O III] are similar and travelling in the same direction while the other species [Ne III], He I, and O II share similar velocity of 200kms−1 up in the opposite direction. The complexity of distribution and kinematic structure of the knots revealed in this work indicates a strong tendency towards the hypothesis of multiple triggering events in the past history of A30.

Transverse momentum spectra of +, p, Λ, Ξ or ¯Ξ+, Ω or ¯Ω+ and deuteron (d) in different centrality intervals in Gold-Gold (Au-Au) and Lead-Lead (Pb-Pb) collisions at 62.4 GeV and 2.76 TeV respectively, are analyzed by the blast wave model with Boltzmann Gibbs statistics. We extracted Kinetic freeze out temperature,transverse flow velocity and kinetic freezeout volume from the transverse momentum spectra of the particles. It is observed that the non-strange and strange (multi-strange) particles freezeout separately due to different reaction cross-sections. While the freezeout volume and transverse flow velocity are mass dependent which decrease with the rest mass of the particles. The present work reveals the scenario of double kinetic freezeout in collisions at STAR and ALICE Collaborations. Furthermore, the kinetic freezeout temperature and freezeout volume are larger in central collisions than the peripheral collisions and they decrease from central to periphery. However the transverse flow velocity remains almost unchanged from central to peripheral collisions.

The application of non-uniform spiral gratings to control structure, topological parameters and propagation of orbital angular momentum (OAM) beams was studied experimentally with coherent near-infrared light. Adapted digital spiral grating structures were programmed into the phase map of a high-resolution liquid-crystal-on-silicon spatial light modulator (LCoS-SLM). It is shown that characteristic spatio-spectral anomalies related to Gouy phase shift can be used as pointers to quantify rotational beam properties. Depending on sign and gradient of spatially variable periods of chirped spiral gratings (CSG), variations of rotation angle and angular velocity as a function of propagation distance were measured. Propagation-dependent self-torque is introduced in analogy to known local self-torque phenomena of OAM beams as obtained by the superposition of temporally chirped or phase modulated wavepackets.

proposal for a fundamental theory is described in which classical and quantum physics as a representation of the universe as a gigantic dendrogram are unified. The latter is the explicate order structure corresponding to the purely number-theoretical implicate order structure given by p-adic numbers. This number field was zero-dimensional, totally disconnected, and disordered. Physical systems (such as electrons, photons) are sub-dendrograms of the universal dendrogram. Measurement process is described as interactions among dendrograms; in particular, quantum measurement problems can be resolved using this process. The theory is realistic, but realism is expressed via the the Leibnitz principle of the Identity of Indiscernible. The classical-quantum interplay is based on the degree of indistinguishability between dendrograms (in which the ergodicity assumption is removed). Depending on this degree, some physical quantities behave more or less in a quantum manner (versus classic manner). Ideologically, our theory is very close to Smolin’s dynamics of difference and Rovelli’s relational quantum mechanics. The presence of classical behavior in nature implies a finiteness of the Universe-dendrogram. (Infinite Universe is considered to be purely quantum.) Reconstruction of events in a four-dimensional space type is based on the holographic principle. Our model reproduces Bell-type correlations in the dendrogramic framework. By adjusting dendrogram complexity, violation of the Bell inequality can be made larger or smaller.

The principle of the constancy of the velocity of light, which stated that the light velocity is invariant to the motion of the emitter, was well established and directly proven by experiments. Interestingly, the further assumption that the light velocity is independent of the motion of the observer was, arguably, never directly proven by any experiment for a century. This paper proposed the design of two experiments to directly test this assumption, which tried to address some perceived technical difficulty in such experiments. One is to directly measure the light speed as to moving sensors. The experiment setup is designed in such a way that the concerns of time synchronization and dilation can be avoided. Another experiment is to test the isotropy of the light speed to a moving particle in the electromagnetic accelerator by measuring the momentum to acceleration ratio. The experiment result, if positive, will provide direct and solid proof of the assumption. Otherwise, it may imply a need for further investigation. Since the light speed invariance to moving observers is a key assumption of some fundamental physical theory, either way, the experiments will have significant meanings.

Electrification coverage in Sarawak is the lowest at 78.74%, compared to Peninsular Malaysia at 99.62% and Sabah at 82.51%. Kapit, Sarawak with its 88.4% populations located in rural areas and mostly situated along the main riverbanks has great potential to generate electrical energy by hydrokinetic system. Yearly water velocity data is the most significant parameter to perform hydrokinetic analysis study. Nevertheless, the data retrieved from local river databases are inadequate for river energy analysis, thus hindering its progression. Instead, flow rates and rainfall data had been utilised to estimate the water velocity data. This signifies no estimation of water velocity in an unregulated river by using water level data had been made. Therefore, a novel technique of estimating the daily average water velocity data in unregulated rivers is proposed. The modelling of regression equation for water velocity estimation was performed and two regression model equations were generated to estimate both water level and water velocity on-site and proven to be valid as the coefficient of determination values had been R² = 87.4% and R²=87.9%, respectively. The combination of both regression model equations can be used to estimate long-term time series water velocity data for type-C unregulated river in remote areas.

This paper reports an experimental investigation on compression after low-velocity impact response for two lay-up configurations of symmetric CFRP laminated composite specimens obtained by reversing their angle-ply orientation, namely [0/-45/45/90]s versus [90/45/-45/0]s, the impact velocity of the projectile up to the BVID level being subsequently considered. To this aim, a modified Compression-After-Impact (CAI) test device is proposed that involves clamping the specimen's upper and lower edges between two adjustable wide and flat anti-buckling plates through a removable bolt-nut assembly. Such a solution relies on the fact that the specimen's active length is shortened, reducing the risk of global buckling. Besides, the bolts carry part of the load with minor localized bearing damage, provided that the metallic plates act as washers by supporting the bolt-bearing region laterally, thus avoiding crashing failures at the specimens’ loaded edges. With these settings, roughly the same percent decrease in the average values of maximum compression load (i.e., 22%) was recorded for both lay-up configurations impacted up to their BVID threshold, whereas in terms of compressive stiffness behavior, a reduction of 17 % was found for [0/-45/45/90]s specimens compared to 6 % obtained for [90/45/-45/0]s specimens.

Deterministic-stochastic empirical mode decomposition (EMD) is used to obtain low-frequency (non-diffusive, i.e., background velocity) and high-frequency (diffusive, i.e., eddies) components from a Lagrangian drifter‘s trajectory. Eddy characteristics are determined from the time series of eddy trajectories from individual Lagrangian drifter such as the eddy radial scale, eddy velocity scale, eddy Rossby number, and eddy-background kinetic energy ratio. A long-term dataset of the SOund Fixing And Ranging float time series obtained near the California coast by the Naval Postgraduate School from 1992 to 2004 at depth between 150 and 600 m (http://www.oc.nps.edu/npsRAFOS/) is used as an example to demonstrate the capability of the deterministic-stochastic EMD.

The main objective of this communication is to describe the ‘Global Salt Cycle’. Giant salt accumulations are commonly found along continental margins of former rifts. The first stage in the accumulation process is saturation of newly formed oceanic crust with seawater. Final mobilisation and accumulation of the salts occurs during rifting, localised in the vicinity of relict subduction zones. Oceanic crust is created along the spreading ridges in the deep oceans of the Earth. It exchanges mass and energy with seawater in hydrothermal circulation cells that penetrate deep into the new and fractured crust. Water-rock interactions include the formation of hydrated and hydroxylated minerals, e.g., serpentinites and clay minerals. By incorporating hydroxyl groups and water in their crystal lattices, the salinity of remaining brines increases. Subduction of oceanic crust and serpentinised lithosphere transports water, hydrated minerals, and marine salts deep into the crust and mantle. Upon pressurisation and heating of the subducting slab, different parts of this water are expelled at different depths/temperatures. The resulting fluids will contain salts brought in with the slab, as well as new salts formed by water-rock interaction. The combination of elevated pressures and temperatures, water, salinity, and CO2, create permeability in the normally impermeable, peridotitic mantle, by altering the fluid-rock dihedral angles of mineral grains. This P/T-determined intergranular permeability allows ascent of saline fluids, under lithostatic pressure, within the mantle wedge, or the slab itself. The fluids produce a mechanically weakened and buoyant zone within the mantle wedge due to high pore pressure between mineral grains and reduced mantle density. During the lifetime of a subduction zone, a substantial accumulation of saline fluids within the mantle wedge and crust, is evident. Deep, fluid reservoirs accumulate between the subduction trench and the volcanic front. They may exist for hundreds of millions of years, even after the extinction of the subduction zone. Saline fluids may escape to the surface along deep faults, due to overfilling of available pores/fractures. Fluids within the mantle wedge may form rock melts or exist as supercritical, mineral rich fluids. The combination of reduced pressure due to rifting, and a saline and buoyant mantle, creates a mantle circulation that brings the accumulated, saline fluids, to crustal levels. Salts will therefore accumulate during initial stages of rifting as a result of massive fluid expulsion, phase change and boiling of mantle fluids. No extra energy is required to produce phase change and boiling. The result is formation of solid salts or dense brines/slurries invading fractured crustal rocks, or escaping to the surface/seabed. This process may take place both before and after the sea has invaded a continental rift.