The hybrid system is analyzed and optimized to produce electric energy in Non-Interconnected Zones in the Colombian Caribbean region, contributing both to the improvement in the reduction of greenhouse gas emissions and to the rational use of energy. A comparative analysis of the performance of these systems was carried using a dynamic model in real wind and solar data. The model is integrated by a Southwest Wind Power Inc. wind turbine. AIR 403, a proton exchange fuel cell (PEM), an electrolyze, a solar panel and a charge regulator based on PID controllers to manipulate oxygen and hydrogen flows in the cell. The transient responses of the cell voltage, current, and power were obtained for the demand of 200 W for changes in solar radiation and wind speed for all days of the year 2013 in the Ernesto Cortissoz airport, Puerto Bolívar, Alfonso Lopez airport and Simon Bolívar airport, by regulating the flow of hydrogen and oxygen into the fuel cell. The maximum contribution of power generation from the fuel cell was presented for the Simon Bolívar airport in November with a value of 158,358W (9.45%). A multi-objective design optimization under a Pareto front is presented for each place studied to minimize the Levelized Cost of Energy and CO₂ emission, where the objective variables are the number of panel and stack in the PV system and PEM.

The processing of woody biomass waste piles for use as fuel instead of burning them was investigated. At each landing slash pile location, a 132 kW grapple excavator was used to transfer the waste piles into a 522 kW horizontal grinder. Economies of scale could be expected when grinding a larger pile, although the efficiency of the loading operation might be diminished. Here, three piles were ground and the operations were time-studied: Small (20 m long × 15 m wide × 4 m high), Medium (30 × 24 × 4 m), and Large (35 × 30 × 4 m) piles. Grinding the Medium pile was found to be the most productive at 30.65 bone dry tons per productive machine hour without delay (BDT/PMH₀), thereby suggesting that there might be an optimum size of slash pile for a grinding operation. We also examined modeling of the excavator and grinder operations, and we observed that the constructed simulation model well-replicated the actual operations. Based on the modeling, we estimated that the productivity of grinding at a landing area of 710 m² of slash pile location was 31.24 BDT/PMH₀, which was the most productive rate.

Recent advancements have revolutionized interplanetary spacecraft missions by combining low-thrust propulsion systems with planetary Gravity-Assist (GA) maneuvers. This study investigates/improved a novel dual-step efficient-robust homotopy algorithm, grounded in indirect optimal control principles, to analyze fuel-optimal bang-bang control problems. The methodology integrates efficient techniques, including the homotopic method, compatible normalization, and improved switching function detection, aimed at enhancing optimal convergence in solving low-thrust gravity-assist spacecraft missions. To illustrate practical application, an Earth-to-Jupiter interplanetary scenario utilizing Mars-GA is examined. Results demonstrate the algorithm's superior efficacy in achieving fuel efficiency, robust convergence, and remarkable accuracy compared to existing solutions.

Nowadays, the increasingly serious environmental pollution and energy problems urgently require internal combustion engine-based transportation vehicles to upgrade or replace, so the new energy transportation vehicles based on hybrid power and fuel cells have gradually stepped on the stage and continue to innovate. The shipping industry is one of the main sources of global greenhouse gas emissions. The development of clean energy ships represented by fuel cells has attracted wide attention. Fuel cell has the advantages of clean, pollution-free and low noise, but it has some disadvantages such as insufficient dynamic response performance and fast performance decay. Limited by the characteristics of a single energy source, a variety of energy sources and bidirectional DC converters are usually mixed together to form a hybrid ship to improve the flexibility, stability and economy of the ship, and enhance its adaptability to complex sea conditions through the reconfiguration of power system energy. Taking fuel cell ferry "FCS Alsterwasser" as the research object, this study proposed an improved equivalent minimum hydrogen consumption energy management strategy based on fuzzy logic control. First, the power system of the modified mother ship was simulated, and a hybrid power system including fuel cell, lithium iron phosphate battery and supercapacitor was proposed. Then, the dynamic system simulation model and double closed loop PI control model are established in MATLAB/Simulink, and the reliability of the model is verified by the simulation analysis of charge and discharge characteristics. Then, the feasibility of the proposed method is demonstrated by designing simulation experiments based on typical working conditions of the mother ship. The simulation results show that under the premise of meeting the load requirements, the control strategy designed in this paper has a better optimization effect than the S-type penalty function in terms of lithium battery power, lithium battery SOC, bus voltage stability and equivalent hydrogen consumption, which improves the stability and economy of the power system, and has certain engineering practical value.

This paper examines the importance of choice of cooking fuels in wellbeing, analysing relationships between the proportion of population with primary reliance on different types of fuels for cooking (predictor variable), and key wellbeing indices (outcome variables) - Personal Health, Social Life, Civic Engagement, Life Evaluation, Negative Experience. By combining two global datasets from Gallup and WHO, the study adds to current evidence by taking a global perspective. Controlling for demographic factors such as income per capita, age, education level, employment, etc., regression modelling of these relationships show that clean cooking fuels are influential in all of the key wellbeing indices with the exception of the Life Evaluation Index. Among the key wellbeing indices, Personal Health and Negative Experience Indices are the most strongly influenced by choice of clean cooking fuels. By adding access to electricity as an additional predictor variable, the analysis highlights the potential for integrating eCooking into national electrification plans as part of sustainable energy transitions, given that health outcomes (Personal health and Negative experience indices) appear to be as closely linked to choice of cooking fuels as to access to electricity.

In this study the formation of thin-film barrier coatings based on a highly-conducting Bi1.60Er0.4O3 (EDB) solid electrolyte on supporting Ce0.8Sm0.2O1.9 (SDC) electrolyte substrates is implemented for the first time using electrophoretic deposition (EPD). Electrokinetic properties of EDB-based suspensions in a non-aqueous dispersion medium of isopropanol modified with small additions of polyethyleneimine (PEI, 0.26 g/L) and acetylacetone (0.15 g/L), as well as in a mixed isopropanol/acetylacetone (70/30 vol.%) medium are studied. The dependences of the thickness of EDB coatings on voltage and deposition time are obtained using deposition on a model Ni-foil electrode. Preliminary synthesis of a conductive polypyrrole (PPy) polymer film is used to create surface conductivity of non-conductive SDC substrates. The efficiency of using a modified dispersion medium based on isopropanol to obtain a continuous EDB coating 12 μm thick, sintered at a temperature of 850 °C for 5 h, is shown. The microstructure and morphology of the surface of the EDB coating are studied. Pt/SDC/EDB/Pt cell is used to characterize the coating conductivity. The EPD method is shown to be promising for the formation of barrier coatings based on doped bismuth oxide. The developed method can be used for creating cathode barrier layers in SOFC technology.

Mushroom production in Poland is an important and dynamically developing element of diverse agriculture. Mushroom spent compost (MSC) is major waste generated during production, i.e., MSC: mushrooms is ~5:1. To date, the main use of MSC is soil application as organic fertilizer. To date, several methods of MSC treatment have been researched and developed including production of compost, bioethanol, biogas, enzyme lactase, xylo-saccharides, and hydrogen. Torrefaction may be considered a novel approach for biomass valorization. Thus, we are pioneering the potential use of MSC valorization via torrefaction. We explored valorizing the waste biomass of MSC via thermal treatment – torrefaction (‘roasting’) to produce biochar with improved fuel properties. Here for the first time, we examined and summarized the MSC torrefaction thermogravimetric analyses, fuel properties data of raw biomass of MSC and biochars generated from MSC via torrefaction. The effects of torrefaction temperature (200~300 °C), process time (20~60 min), on fuel properties of the resulting biochars were summarized. The dataset contains results of thermogravimetric analysis (TGA) as well as proximate analyses of MSC and generated biochars. The presented data are useful in determining MSC torrefaction reaction kinetics, activation energy and to further techno-economical modeling of the feasibility of MSC valorization via torrefaction. MSC torrefaction could be exploited as part of valorization resulting from a synergy between an intensive mushroom production with the efficient production of high-quality renewable fuel.

Microbial electrochemical technologies (MET) rely on the presence of the metabolic activity of electroactive bacteria for the use of solid-state electrodes for oxidizing different kind of compound, that could lead to the synthesis of chemicals, bioremediation of polluted matrices, the treatment of contaminants of interest, as well as the recovery of energy. Keeping in mind those possibilities, since the beginning of the present century, there has been a growing interest in the use of electrochemical technologies for wastewater treatment, and if possible with simultaneous power generation. In the last years, there has been a growing interest to explore the possibility of merging MET with constructed wetlands, to offer a new option of intensified wetland system that could keep a high performance with a lower footprint. Based on that interest, this paper explains the general principles of MET, and the different known extracellular electron transfer mechanisms ruling the interaction between electroactive bacteria and potential solid-state electron acceptors. Also, the adoption of those principles for the development of MET set-ups for simultaneous wastewater treatment and power generation, and the challenges that the technology face. Ultimately, the most recent developments in set-ups that merges MET with constructed wetlands are presented and discussed.

The EU’s energy targets are to achieve at least 32% renewables in the energy mix by 2030. Part of the solution is strengthening consumer rights by empowering individuals to generate their own electricity. The study aimed to identify the most suitable energy system for electricity generation of up to 50 kW in the EU residential sector. The Multi-Criteria Decision Analysis was used to compare four systems: proton exchange membrane fuel cell with photovoltaic panels, photovoltaic panels, biomass powered Stirling engine, and solar powered Stirling engine. Based on the results, the most beneficial system for household electricity generation is the Biomass-fueled Stirling engine system due to its affordability, reliability, and low environmental impact. Governments and businesses can use these findings to improve information for the residential sector and enable the transition to renewable energy.

In this research the possibility of using pH change to measure proton conductivity of proton exchange membranes (PEM) or else known as polymer electrolyte membranes are tested with using an experimental setup prepared by using pH meters. PEMs are an important part of the fuel cells and proton conductivity of the PEMs are one of the most important properties of the PEMs. Also, proton conductivity is the one of the biggest limiting factors of fuel cells thus it is important to measure the proton conductivity of the PEMs while trying new polymers or new types of membranes. But as current measurement methods do not have a standard and can be separated into mainly two different measurement methods which are Electron Impedance Spectroscopy (EIS) and Ion Exchange Capacity (IEC). EIS gives clearer results, but it needs an impedance analyzer machine, platinum electrodes and setup so this cannot be possible for every researcher due to its economical aspect. For IEC it is basically a titration method to see acid groups in the polymer or polymer matrix which are directly responsible for proton conductivity so this can show an indirect measurement of proton conductivity. But as for this one drawback are firstly this one is an indirect measurement and secondly needs overnight bath in solution can take long times. So, the possibility of using pH can be easier and both from time and economical aspect if it can be proven the give a direct relationship between pH change and proton conductivity.

This paper presents a new methodology to evaluate the performance of an electric vehicle hybrid power system consisting of a fuel cell and a supercapacitor. The study compares the results with those obtained for a battery-electric vehicle. The methodology extends to three driving modes, ECO, NORMAL, and SPORT, corresponding to conservative, moderate, and aggressive acceleration, and three driving conditions, low, medium, and high energy demand. We develop a simulation process to evaluate the energy consumption and the energy rate of a specific electric vehicle used as a prototype for the study. The methodology applies to a driving route that includes acceleration, deceleration, braking, and constant speed segments reproducing standard driving conditions in urban journeys. The proposed method considers combined driving modes, ECO, NORMAL, and SPORT, in each acceleration process, with variable fractions, 0% to 100%, for each mode. This methodology optimizes the simulation results as it fits the current driving way in urban environments. The simulation results show an average reduction in energy consumption of 37% and 27.1% in vehicle weight, contributing to lower energy use. The study concludes that using a hybrid power system, fuel cell/supercapacitor, instead of a battery in electric vehicles is beneficial, especially in journeys with frequent acceleration processes.

By 2020, over 100 countries expanded electric and plug-in hybrid electric vehicle (EV/PHEV) technologies, with global sales surpassing 7 million units. Governments are adopting cleaner vehicle technologies due to proven environmental and health implications of internal combustion engine vehicles (ICEVs), evidenced by the recent COP26 meeting. This article proposes an agent-based model of vehicle activity as a tool for quantifying energy consumption by simulating a fleet of EV/PHEVs within an urban street network at various spatio-temporal resolutions. Driver behaviour plays a significant role in fuel consumption, thus, simulating various levels of individual behaviour enhancing heterogeneity should provide more accurate results of potential energy demand in cities. The study found that 1) energy consumption is lowest when speed limit adherence increases (low variance in behaviour) and is highest when acceleration/deceleration patterns vary (high variance in behaviour) and 2) on average, for tested vehicles, EV/PHEVs were £116.33 cheaper to run than ICEVs across all experiment conditions. The difference in the average fuel costs (electricity and petrol) shrinks at the vehicle level as driver behaviour is less varied (more homogeneous). This research should allow policymakers to quantify the demand for energy and subsequent fuel costs in cities.

This paper develops a Green Light Optimal Speed Advisory (GLOSA) system for buses (B-GLOSA). The proposed B-GLOSA system is implemented on diesel buses, and field tested to validate and quantify the potential real-world benefits. The developed system includes a simple and easy to calibrate fuel consumption model that computes instantaneous diesel bus fuel consumption rates. The bus fuel consumption model, a vehicle dynamics model, the traffic signal timings, and the re-lationship between vehicle speed and distance to the intersection are used to construct an optimi-zation problem. A moving-horizon dynamic programming problem solved using the A-star algo-rithm is used to compute the energy-optimized vehicle trajectory through signalized intersections. The Virginia Smart Road test facility was used to conduct the field test on 30 participants. Each participant drove three scenarios including a base case uninformed drive, an informed drive with signal timing information communicated to the driver, and an informed drive with the recom-mended speed computed by the B-GLOSA system. The field test investigated the performance of using the developed B-GLOSA system considering different impact factors, including road grades and red indication offsets, using a split-split-plot experimental design. The test results demonstrated that the proposed B-GLOSA system can produce smoother bus trajectories through signalized in-tersections producing fuel consumption and travel time savings. Specifically, compared to the uninformed drive, the B-GLOSA system produces fuel and travel time savings of 22.1% and 6.1% on average, respectively.

Ponderosa pine is an integral part of the forested landscape in the western US; it is the dominant tree species on landscapes that provide critical ecosystem services. Moderate drought tolerance allows it to occupy the transition zone between forests and open woodlands and grasslands. Increases in stand density resulting from wildfire suppression, combined with lengthening, intensifying and more frequent droughts have resulted in reduced tree vigor and stand health in dry ponderosa pine throughout its range. To address a management need for efficient landscape-level surveys of forest health, we used Random Forests to develop an object-oriented classification of individual tree crowns (ITCs) into vigor classes using existing, agency acquired 4-band aerial imagery. Classes of tree vigor were based on quantitative physiological and morphological attributes established in a previous study. We applied our model across a landscape dominated by ponderosa pine with a variety of forest treatments to assess their impacts on tree vigor and stand health. We found that stands that were both thinned and burned had the lowest proportion of low vigor ITCs, and that stands treated before the 2014-2016 drought had lower proportions of low vigor ITCs than stands treated more recently (2016). Upland stands had significantly higher proportions of low vigor trees than lowland stands. Maps identifying the low vigor ITCs would assist managers in identifying priority stands for treatment and marking trees for harvest or retention. These maps can be created using already available imagery and GIS software.

The noble metals palladium and silver find use in many high performance applications, and their alloys (PdAg), known for more than sixty years, are industrially important, finding use in many fields including hydrogen purification and separation, numerous facets of catalysis, and in fuel cells. In recent years, interest in these materials has grown significantly, particularly in energy generating applications and due to their performance as solid-state chemical sensors for a range of small molecules. PdAg thin films can be prepared using traditional physical methods such as cold rolling, or more modern and controllable chemical or physical deposition techniques such as electrodeposition or chemical vapour deposition. Despite the wide-reaching uses of PdAg, several recent advancements in materials preparation, such as additive manufacturing, better known as 3-D printing, remain unexplored for this material due to the differing chemistries of the two elements. In this review, we explore the manufacturing methods commonly employed for the preparation of PdAg thin films, the common and niche applications of these materials, and opportunities for the future development of these two aspects, with an emphasis on how preparation of thin films can utilise additive manufacturing approaches.

Relying on Random Utility Theory (RUT) as the guiding mechanism for the Data Generating Process (DGP), this paper uses households consumption choices on cooking fuel, drinking water, and sanitation from the 2014 United States Agency for International Development's (USAID) Demographic and Health Survey (DHS) data on Burkina Faso, to characterize and investigate the inter-linkages between health consciousness and environmental consciousness, and their relationship with wealth in a low income country context. We achieve this by specifying sequentially three econometric modeling frameworks: the first one being independent binary probit (IBP) models to describe each choice process, followed by a fully parametric trivariate probit (FPTP) model to account for choice dependency, and finally by a semi-parametric trivariate probit (SPTP) model to further relax the linearity assumption. Based on the Akaike Information criteria (AIC) and the estimated Trivariate model correlation coefficients, the SPTP framework is found to be the best specification for describing the observed consumption behaviors. The results show that increased wealth level raises households health and environmental consciousness, while leaving the relative preference ordering over the elements in the household consumption basket unchanged.

The World Health Organization identifies alcohol as a cause in several neoplasias of the oro-pharynx cavity, esophagus, gastrointestinal tract, larynx, liver, or female breast. This study re-views ethanol's nonoxidative and oxidative metabolism and one-carbon metabolism that en-compasses both redox and transfer reactions that influence crucial cell proliferation machinery. Ethanol favors the uncontrolled production and action of free radicals that interfere with the maintenance of essential cellular functions. We focus on the generation of protein, DNA, and lipid adducts that interfere with the cellular processes related to growth and differentiation. Ethanol's effects on stem cells responsible for building and repairing tissues are reviewed. Cancer stem cells suffer disturbances related to the expression of cell surface markers, enzymes, and transcription factors after ethanol exposure with consequent dysregulation of mechanisms related to cancer metastasis or resistance to treatments. Our analysis aims to underlie and discuss potential targets that show more sensitivity to ethanol's action and identify specific metabolic routes and metabolic realms that may be corrected to recover metabolic homeostasis after pharmacological interven-tion. Specifically, research should pay attention to reestablish metabolic fluxes by fine-tuning the functioning of specific pathways related to one-carbon metabolism and antioxidant processes.

Hydrogen plays an important role in the implementation of Australia’s Net-Zero Strategy. It competes with lithium-ion rechargeable batteries in the electrification of Australian land transportation sector, and can provide an alternative energy storage medium for the greening of the country’s electrical grid system. This paper reviews the role hydrogen plays in the current government’s Net-Zero strategy, and investigates the potential role of other bioenergy sources. It is found that hydrogen and batteries play essentially complementary roles in reducing transport emissions, and that the former energy source is more suited to the operation of long-distance commercial service vehicles than batteries. It is suggested that bioenergy fuels such as biomethane, second generation biofuels and HVO can provide suitable bridging alternatives in the event that Australia’s EV strategy is unable to meet the 2030 target.

Environmental pollution is becoming ubiquitous; it has a negative impact on the ecosystem diversity and worsens the quality of human life. This review discusses the possibility of applying the Plant Microbial Fuel Cells (PMFC) technology for concurrent processes of electricity generation, purification of water and soil ecosystems from organic pollutants, in particular, from synthetic surfactants and heavy metals. The review describes the PMFC functioning mechanisms and highlights the issues of the PMFC environmental application. Generally, this work summarizes different approaches to the PMFC development and to the potential usage of such hybrid bioelectrochemical systems for the environmental protection.

This work aims to study and analyze a hybrid power system for electric vehicles consisting of a dual low and high-rate lithium battery block and a fuel cell. In this configuration, the high-rate lithium battery powers the electric vehicle in high power demand processes like acceleration mode or on an uphill road; the low-rate battery operates at a low output power range, servicing the auxiliary systems and low power loads and the fuel cell supplies energy at intermediate power demand conditions, normal driving mode, constant velocity, or flat and downhill terrain. The dual power system improves global efficiency since every power unit operates optimally depending on driving conditions. Power sharing optimizes the lithium battery performance and fuel cell capacity, minimizing the size and weight of each energy system and enlarging the driving range. A comparative study between different lithium battery configurations and fuel cell shows an efficiency improvement of 31.4% for the hybrid dual battery block and fuel cell operating in low, high, and intermediate output power ranges, respectively. The study bases on a simulation process recreating current driving conditions for electric cars in urban, peripheral, and intercity routes. An alternative solution consisting of a hybrid system, fuel cell and a high rate lithium battery produces a 29 % power gain.

In view of the problem of charging and hydrogen filling facilities construction in the transition from fuel vehicles to electric vehicles and hydrogen fuel cell vehicles, in order to meet the electric energy demand of electric vehicles and hydrogen energy demand of hydrogen fuel cell vehicles at the same time, this paper puts forward a method of siting and capacity determination of electric-hydrogen refueling integrated station (EHRIS) based on Voronoi diagram and particle swarm algorithm based on calculating the demand of charging and filling of hydrogen in vehicles. Firstly, OD pair(Origin-Destination) is used to represent the starting point and end point of the car to portray the travel demand of the car, and on the basis of the traffic network model, the shortest driving path of the new energy car is determined by Dijkstra algorithm, and Monte Carlo simulation is used to get the electric-hydrogen energy demand of the car; secondly, the Voronoi diagram is introduced to classify the service scope of the electric-hydrogen charging station to determine the equipment capacity of the electric-hydrogen charging station, while taking into account the electric-hydrogen charging and refueling capacity. Secondly, a Voronoi diagram is introduced to divide the service scope of the EHRIS, determine the capacity of the equipment in the EHRIS, and consider the distance constraints between the sites of EHRIS, so as to make the division of the site and service scope more reasonable. Finally, a dynamic optimal current model framework for distribution networks based on second-order cone relaxation is established, and each element of the active distribution network is planned, so that the distribution network can operate safely and stably after being connected to the EHRIS. With the objective of minimizing the total social cost of EHRIS and considering the constraints of the charging equipment and hydrogen production and injection equipment of the EHRIS, a siting and capacity model to meet the electric-hydrogen energy demand of electric and hydrogen fuel cell vehicles is developed, and solved by a particle swarm algorithm. Finally, the simulation planning is carried out with Sioux Falls city and IEEE33 network, which ensures the stable operation of the power grid while meeting the energy demand of automobiles, and the results verify the effectiveness and feasibility of the proposed method.

In air-breathing proton exchange membrane fuel cells (Air PEM FCs), high rate of water evaporation from the cathode might influence the resistance of the membrane electrode assembly (MEA), which is highly dependent on the water content of the Nafion membrane. We propose a dead-end hydrogen anode as a means of intermediate storage of water/humidity for self-humidification of the membrane. Such inflatable bag integrated with the PEM FC has a potential in blimp applications for anode self-humidification. A dynamic numerical water balance model, validated by experimental measurements, is derived to predict the effect of MEA configuration, membrane’s hydration state, and water transfer rate at the anode on MEA resistance and performance. The experimental setup included humidity measurements, polarization and electrochemical impedance spectroscopy tests to quantify the effect of membrane hydration on its resistance in a lightweight MEA integrated with an inflatable dead-end hydrogen storage bag. Varying current density (20 mA, 40 mA and 60 mA) and cathode humidity (20, 50 and 80%) were examined and compared with the numerical results. The validated model predicts that the hydration state of the membrane and water transfer rate at the anode can be increased by using a thin membrane and thicker gas diffusion layer.

This paper defines the two main causes of global warming in the UK and seeks to cut climate change using green hydrogen made from renewable electricity sources. Combustion vehicles powered by fossil gasoline and diesel emit a third of UK climate-warming CO2 while buildings heated by natural gas provide a quarter. First, current UK grid problems are defined: Electricity grid, gas grid and petroleum grid. Then experiments on the private energy community of Keele University allow electrolysis demonstrations producing green hydrogen for buildings and vehicle refueling. Next, the model supply chain is planned and tested. Finally, experiments and calculations are outlined, analyzing the optimum system design criteria proposed. We conclude that economic green hydrogen can displace diesel and gasoline in vehicle transport, while also displacing natural gas for combined heat and power in buildings. In addition, the prospect in 2023 is that profits can now be made all along the green hydrogen supply chain, such that new businesses involved in clean communities can beat the National Grid monopoly and other large dominant fossil grid companies.

Oxygen and hydrogen mobility are among the important characteristics for operation of solid oxide fuel cells, permselective membranes and many other electrochemical devices. This, along with other characteristics, enables reaching a high power density of solid oxide fuel cells and a high oxygen or hydrogen permeation fluxes for membranes. This work focuses on oxygen and hydrogen diffusion of mixed ionic (oxide ionic or/and protonic) – electronic conducting materials for these devices and its role in the performance. Ionic transport properties of conventional and state-of-the-art materials are reviewed.

To accomplish IMO's emissions reduction targets, the Chinese government has established emission control areas and implemented strict sulfur limitation policies. Faced with the downturn in the shipping industry and the challenge of insufficient supply of compliant fuel, Hong Kong and Shenzhen in China have implemented different low-sulfur fuel subsidy policies. Therefore, it is particularly important to study the air pollution control mechanism considering low sulfur fuel subsidy policy. Firstly, the non-cooperative game models considering low-sulfur fuel subsidies are constructed. Secondly, the mechanisms of various factors affecting port pricing, throughput and profit are analyzed. Then, a case study is conducted by using AIS data of container ships in Shanghai Port and Ningbo Zhoushan Port. The study reveals that whether the container service price of the leader port increases or decreases, the follower port always take corresponding follow-up measures. In both sequential and simultaneous game, the profit difference of the leader port is positively related to the subsidy ratio of the port’s own and negatively related to the coefficient of the competitor's subsidy. In conclusion, the low-sulfur fuel subsidy policy has a significant positive impact on the step-by-step implementation of more stringent pollution reduction policies in port waters.

The aspirated hypersonic air-breathing propulsion system requires a large amount of power generation, but its special structure makes it impossible to adopt common power generation methods. The high-temperature gaseous hydrocarbon fuel thermal power generation (TPG) system was developed to solve the power generation problem for hypersonic air-breathing propulsion system. But off-design operating conditions of the hypersonic propulsion system results in a more complex process for both propulsion system and the TPG system. To better analyzing the dynamic thermos-physical characteristics of hypersonic airbreathing propulsion system considering thermal-mechanical coupling process among cooling/TPG system, a dynamic analytical model was developed, and the dynamic thermos-physical characteristics of TPG system under different off-design working conditions were conducted. It can be concluded from the analytical results that the dynamic process of thermos-physical characteristics shows a complex trend under the flight Mach number and fuel equivalence ratio off-design working conditions. Such complexity of dynamic characteristics brings difficulties in fuel supply for the propulsion system.

The application of thermoelectric generators (TEG) on the nozzle of an aviation jet engine was studied by finite element TEG-simulations. Against the background of system-level requirements of the reference aircraft this work reports the resulting requirements on the TEG design with respect to applied thermoelectric (TE) element lengths and fill factors (F) within the TE modules in order to maintain a positive effect on the specific fuel consumption. Assuming a virtual optimized TE material and varying the convective heat transfer coefficients at the nozzle surfaces this work reports the achievable power output. System-level requirement on the gravimetric power density (> 100 Wkg-1) can only be met for F ≤ 21%. Extrapolating TEG coverage to the full nozzle surface, the power output reaches 1.65 kW per engine. Assessment of further potential is demonstrated by a parametric study on the fill factor, convective heat transfer coefficients, and materials performance. This study confirms a feasible design range for TEG installation on the aircraft nozzle with a positive impact on the fuel consumption. This application translates into a reduction of operational costs, allowing for an economically efficient installation of TEG in consideration of the cost-specific power output of modern thermoelectric materials.

The anode of a microbial fuel cell (MFC) was formed on a graphite electrode and immobilized Gluconobacter oxydans VKM-1280 bacterial cells. Immobilization was performed in chitosan, poly(vinyl alcohol) or N-vinylpyrrolidone-modified poly(vinyl alcohol). Ethanol was used as substrate. The anode was modified using multiwalled carbon nanotubes. The aim of the modification was to create a conductive network between cell lipid membranes, containing exposed PQQ-dependent alcoholdehydrogenases, and the electrode to facilitate electron transfer in the system. The bioelectrochemical characteristics of modified anodes at various cell/polymer ratios were assessed via current density, power density, polarization curves and impedance spectres. MFCs based on chitosan at a matrix/cell volume ratio of 5:1 produced maximal power characteristics of the system (8.3 μW/cm2) at a minimal resistance (1111 Ohm cm2). Modification of the anode by multiwalled carbon nanotubes led to a slight decrease of internal resistance (down to 1078 Ohm cm2) and to an increase of generated power density up to 10.6 μW/cm2. We explored the possibility of accumulating electric energy from an MFC on a 6,800-μF capacitor via a boost converter. Generated voltage was increased from 0.3 V up to 3.2 V. Accumulated energy was used to power a Clark-type biosensor and a bluetooth transmitter with three sensors, a miniature electric motor and a light-emitting diode.

Energy is a fundamental ingredient in economic development and energy consumption is an index of prosperity and the standard of living. The consumption of energy has increased significantly in the last number of decades, as the standard of living has improved. Renewable energy is a sustainable and clean source of energy derived from nature. Renewable energy technology is one of the solutions, which produces energy by transforming natural resources into useful energy forms. When you do something for the first time in the world, you never attain a perfect product or solution from the start. In Central Greece Lamia city, we are the first to design and implement an off-grid energy system using hydrogen energy storage technology and phase change materials for a house residence. The action plan for energy efficiency, a series of directives and incentive mechanisms, mandatory energy certification of buildings, indicate the urgent need to reduce energy consumption in buildings, which results in a more comfortable living, long service life of buildings, which in turn preserves the environment.

The option of decarbonizing urban freight transport using Battery Electric Vehicle (BEV) seems promising.However, there is currently a strong debate whether Fuel Cell Electric Vehicle (FCEV) might be the bettersolution. The question arises as to how a fleet of FCEV influences the operating cost, the Greenhouse Gas(GHG) emissions and primary energy demand in comparison to BEVs and to Internal Combustion EngineVehicle (ICEV). To investigate this, we simulate the urban food retailing as a representative share of urbanfreight transport using a multi-agent transport simulation software. Synthetic routes as well as fleet size andcomposition are determined by solving a Vehicle Routing Problem (VRP). We compute the operating costsusing a total cost of ownership (Total Cost of Ownership (TCO)) analysis and the use phase emissions as wellas primary energy demand using the Well To Wheel (WTW) approach. While a change to BEV results in 17 -23% higher costs compared to ICEV, using FCEVs leads to 22 - 57% higher costs. Assuming today’s electricitymix, we show a GHG emission reduction of 25% compared to the ICEV base case when using BEV. Currenthydrogen production leads to a GHG reduction of 33% when using FCEV which however cannot be scaled tolarger fleets. Using current electricity in electrolysis will increase GHG emission by 60% compared to the basecase. Assuming 100% renewable electricity for charging and hydrogen production, the reduction from FCEVsrises to 73% and from BEV to 92%. The primary energy requirement for BEV is in all cases lower and forhigher compared to the base case. We conclude that while FCEV have a slightly higher GHG savings potentialwith current hydrogen, BEV are the favored technology for urban freight transport from an economic andecological point of view, considering the increasing shares of renewable energies in the grid mix.

One of the most important objectives of the studies worldwide is to improve the performance of automotive engines to reduce fuel consumption and environmental pollution. Accordingly, the principal motivation of this research study is improving the tribological behavior of the piston ring/cylinder liner interfaces as a promising and straightforward approach in automotive fuel economy and increasing engine durability using Al₂O₃ and TiO₂ nanomaterials as smart nano-lubricant additives that adapted to different operating conditions by replenishing mechanisms anti-friction and anti-wear in automotive engines.

This study develops into the application of a combined MFC unit with chemical coagulation for total treatment of inert contaminants in complex substrates. Microbial Fuel Cell (MFC) technology converts chemical energy in the form of organic matter, into bioelectricity in an environmentally friendly and effi-cient manner, reducing carbon emissions and increasing bioenergy production. An evaluation of a la-boratory scale chemical coagulation using an aluminum and poly-based coagulant on how effective it can remove bulk impurities such as particulate COD and turbidity to obtain the purest and most cost-effectively treated wastewater using a jar test is being conducted in this current study. This study aims to find the most effective treatment technologies for wastewater recovery in breweries in order to achieve zero liquid effluent discharge (ZLED). The preliminary results showed that adding a modest amount of poly and a 50 % alum alone treatment improved COD, color, and turbidity reduction. The turbidity removal efficiency achieved after chemical coagulation treatment was 90.50 % and 59.36 % COD removal, demonstrating the benefits of adopting an alum/poly based technique. To determine ZLED, this study clearly advised a combined treatment technique, specifically the MFC-flocculator unit for efficient organics and inorganics removal.

Peat is the main type of peloid used in Polish cosmetic/healing spa facilities. Depending on treatment and origin, peat waste can be contaminated microbiologically, and as result, it has to be incinerated in medical waste incineration plants without energy recovery (local law). Such a situation leads to peat waste management costs increase. Therefore in this work, we checked the possibility of peat waste upcycling to carbonized solid fuel (CSF) using torrefaction. Torrefaction is a thermal treatment process that removes microbiological contamination and improves the fuel properties of peat waste. In work torrefaction conditions (temperature and time) on CSF quality were tested. Parallelly, peat decomposition kinetics using TGA, and torrefaction kinetics with lifetime prediction using macro-TGA were determined. Furthermore, torrefaction theoretical mass and energy balance were determined. The results of the tested peat were compared with reference material (wood), and as result, obtained data can be used to adjust currently used wood torrefaction technologies for peat torrefaction. The results show that torrefaction can improve the high heating value of peat waste from 19.0 MJ x kg-1 to 21.3 MJ x kg-1, peat main decomposition takes place at 200-550 °C following second reaction order (n=2), with an activation energy of 33.34 kJ x mol-1 and pre-exponential factor of 4.40 x 10-1 s-1. Moreover, DSC analysis revealed that peat torrefaction required slightly more energy than wood torrefaction, and macro TGA showed that peat torrefaction has lower torrefaction constant reaction rates (k) than wood 1.05 x 10-5 - 3.15 x 10-5 vs 1.43 x 10-5 - 7.25 x 10-5 s-1.

Behavior of supported alloyed and de-alloyed platinum-copper catalysts, which contained 14% - 27% wt. of Pt, was studied in the reactions of methanol electrooxidation (MOR) and oxygen electroreduction (ORR) in 0.1 M HClO4 solutions. Alloyed PtCux/C catalysts were prepared by a multistage sequential deposition of copper and platinum onto a Vulcan XC72 dispersed carbon support. De-alloyed PtCux-y/C catalysts were prepared by PtCux/C materials pretreatment in acid solutions. The effects of the catalysts initial composition and the acid treatment condition on their composition, structure, and catalytic activity in MOR and ORR were studied. Functional characteristics of platinum-copper catalysts were compared with those of commercial Pt/C catalysts when tested, both in an electrochemical cell and in H2/Air membrane-electrode assembly (MEA). It was shown that the acid pretreatment of platinum-copper catalysts practically does not have negative effect on their catalytic activity, but it reduces the amount of copper passing into the solution during the subsequent electrochemical study. The activity of platinum-copper catalysts in the MOR and the current-voltage characteristics of the H2/Air PEMFC MEAs measured in the process of their life tests were much higher than those of the Pt/C catalysts.

Poland is the 3^rdproducer of mushrooms in the world. Mushroom production in Poland accounts for nearly 25% of the total production in the EU, and it is still growing. One type of waste generated during mushroom production is mushroom spent compost (MSC), with a 5:1 (MSC: mushrooms) production rate. We investigated valorizing the MSC to produce fuel via torrefaction (‘roasting’, a.k.a. low-temperature pyrolysis). Specifically, we developed models for the MSC torrefaction kinetics using thermogravimetric analyses (TGA) and the effects of torrefaction temperature (200~300 °C) and process duration time (20~60 min) on the resulting biochar (fuel) properties. The estimated activation energy value of MSC torrefaction was 22.3 kJ^.mol^-1. The highest higher heating value(HHV) = 17.9 MJ^.kg^-1d.m. was found for 280 °C (60 min torrefaction time). The temperature of torrefaction significantly (p<0.05) increased the HHVfor constant process duration. The torrefaction duration time significantly (p<0.05) increased the HHVfor 220 °C and decreased HHVfor 300 °C. The highest mass yield 98.5% was found for 220 °C (60 min), while the highest energy yield was found for 280 °C (60 min). In addition, estimations of the value (€132.3·Mg^-1d.m. or 27.7 €·Mg^-1w.m) and quantity of resulting biochar (from torrefied MSC with 65.3% moisture content) were made based on the 280°C (60 min) torrefaction variant, assuming the price of commercially available coal fuel. We have shown a concept for an alternative utilization of abundant biowaste (MSC). The initial economic evaluation showed that MSC torrefaction might be profitable. This research provides a basis for alternative use of an abundant biowaste and can help charting improved, sustainable mushroom production.

In fuel-cell technological development, one of the most important objectives is to minimize the amount of Pt, the most employed material as oxygen reduction and methanol oxidation electro-catalyst. In this paper we report the synthesis and characterization of Te nanotubes (TeNTs) decorated with Pt nanoparticles, readily prepared from stirred aqueous solutions of PtCl2 containing a suspension of TeNTs and ethanol acting as a reducing agent, avoiding the use of any hydrophobic surfactants as capping stabilizing substance. The as obtained TeNTs decorated with Pt nanoparticles (TeNTs/PtNPs) have been fully characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), selected area diffraction patterns (SAD), X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry (CV). We demonstrate that the new material can be successfully employed in fuel cell either as anodic (for methanol oxidation reaction) and cathodic (for oxygen reduction reaction) electrode with high efficiency in terms of related mass activities and on-set improvement. Remarkably, the cell operates in aqueous electrolyte buffered at pH 7.0, thus avoiding acidic or alkaline conditions that may lead e. g. to Pt dissolution (at low pH) and paving the way for the development of biocompatible devices and on chip fuel cells.

Is it true that the nuclear technology applied to electric energy generation offers a clean, safe, reliable and affordable i.e. sustainable alternative? Yes it is, but its impact on the environment strongly depends on the implementation bearing residual risks due to a human factor, technical failures or natural catastrophes. A full response is therefore difficult and can first be given when the wicked multi-disciplinary problems get well formulated and “solved”. These problems have multi-dimensional nature lying at the interface between: necessary R&D effort, the industrial deployment and the technology impact in view of the environmental sustainability including the management of produced hazardous waste. This enormous complexity indicates that just a description of the problem might represent a problem. The paper proposes a holistic approach to assess the nuclear energy systems potential with respect to sustainable performance applying Multi-criteria decision analysis with a suitable objective tree and a multi-level criteria structure and examines the trading-off techniques for ranking of the alternatives. The framework proposes a multi-criteria and multi-stakeholders treatment which can be used as a pre-decisional support towards an implementation of nuclear fuel cycles adapted to national preferences and priorities. Proposed approach addresses some aspects of the environmental footprint of nuclear energy systems. Advanced nuclear fuel cycles, previously investigated by the NEA/OECD expert group WASTEMAN, are analyzed as a case study. Sustainability facets of waste management, resource utilization and economics are in focus.

Conventional greenhouse accounting inadequately describes land use/land use change and forestry (LULUCF) emissions, cooling emissions, and sequestration potential. As we enter the age of drawdown, we propose an accounting framework that offers greater consistency and transparency. By unfolding net accounting of LULUCF CO2 emissions; aggregating biosphere sinks; accounting for all emissions (heating and cooling); com-paring sectors with emissions-based Effective Radiative Forcing (ERF) rather than global warming potential; and including drawdown potential of land use carbon opportunity cost (COC), this reveals fresh insight into sector contributions and mitigation potential. Consistent gross emissions reporting of LULUCF CO2 emissions finds these to be at least 3.5 times greater than conventionally understood. Consolidating natural sequestration on ‘managed’ and ‘intact’ land, we find that since 1750 vegetation and the oceans have removed from the atmosphere an amount equivalent to 2.4 times cumulative fossil fuel CO2 emissions, demonstrating the immense drawdown potential of the biosphere. This accounting places deforestation (responsible for 77% of LULUCF emissions) as the main source of historic CO2 emissions, and attributes drawdown potential COC to sectors. The most extensive land use sector, animal agriculture, was found to have contributed the greatest warming (52% of net ERF since 1750) and to offer the greatest drawdown potential COC.

Spent nuclear fuel and high-level radioactive waste can be disposed in deep horizontal drillholes in sedimentary, metamorphic, or igneous rocks. Horizontal drillhole disposal has safety, operational, and economic benefits: The repository is deep in the brine-saturated zone far below aquifers in a reducing environment of formations that can be shown to have been isolated from the surface for millions of years; its depth provides safety against inadvertent intrusion, earth¬quakes, and near-surface perturbations; it can be placed close to the reactors and interim storage facilities, minimizing transportation; disposal costs per ton of waste can be kept substantially lower than for mined repositories by its smaller size, reduced infrastructure needs, and staged imple¬mentation; and, if desired, the waste could be retrieved using “fishing” technology. In the proposed disposal concept, corrosion-resistant canisters containing unmodified fuel assemblies from commercial reactors would be placed end-to-end in up to 50 cm diameter horizontal drill¬holes, a configuration that reduces mechanical stresses and keeps the temperatures below the boiling point of the brine. Other high-level wastes, such as capsules containing 137Cs and 90Sr, can be disposed in small-diameter drillholes. We provide an overview of this novel disposal concept and its technology, discuss some of its safety aspects, and compare it to mined repositories and the deep vertical borehole disposal concept.

The aim of this research was to investigate the mass, substances and energy flow through two-stroke low speed Diesel engines. For this reason, a zero-dimensional model of the combustion in the engine was developed with a calculated amount and composition of exhaust gases. Due to the large amount of oxygen in the exhaust gases, a ratio of real air consumption and stoichiometric amount of air required for combustion of injected fuel was set. The calculated ratio showed that the engine consumes four times more air than needed for combustion in AFR_stoich. In this work it is called the Air Consumption Factor or Ratio and has not been mentioned in scientific literature before. Air Consumption Ratio is defined as a factor of dry or humid air. To be more comprehensive, a modified diagram of composition of the flow in and out of a two-stroke fuel injection engine and the cylinder was drawn.

The article studies and analyzes a hybrid power source system, lithium battery, and fuel cell assisted by flexible photovoltaic panels for hybrid electric vehicles (HEVs). The new configuration operates based on optimizing the performance of the dual power source to maximize the available energy and operating time. The operational mode simulates specific driving conditions in urban, peripheral, and intercity routes under variable driving patterns and traffic conditions. The simulation results show that the new configuration increases the hybrid electric vehicle performance, providing higher reliability despite the more complex design. The proposed system reduces the external power supply dependence and avoids unexpected sudden stops due to energy exhaustion. The new configuration also extends the vehicle driving range depending on driving mode and route conditions. The vehicle driving range extension may reach up to 276.3 km. The hybridization of fuel cells with lithium battery and PV panel assistance enhances battery management, reducing battery servicing and increasing lifespan. The proposed topology is cheaper than a single fuel cell power system by 17.2%, reducing the total cost related to the single battery power system if we consider the battery recharge for its entire lifespan. The cost saving is 2.6% for the American market and 14.8% for the European one.

Carbon footprint mitigation actions have become a key issue for companies involved in urban freight transport. The electrification of the delivery fleets is one of the crucial sustainable actions carried out. To this end, it is necessary to explore several fleet renewal strategies over a finite planning horizon evaluating different types of electric powertrains for light commercial vehicles. The primary goal of this purpose-built analysis is to assist and boost the fleet managers' decisions when transitioning to alternative-fuelled vans, intending to maximize cost savings and reduce greenhouse gas emissions inventory. The model presented in this work is a Multi-Objective Linear Programming hybrid analysis taking into account the vehicle and energy supply infrastructure costs and the emissions reported in each inventory scope following the Greenhouse Gas Protocol sustainability guidelines. From this perspective, the conducted research offers a novel approximation to fleet management problems enabling a break-down cost analysis and an evaluation of the annual emissions company report. The comprehensive numerical simulations carried out over different study scenarios in Spain demonstrate that the optimization approach does not only show effective fleet renewal strategies but also identifies critical factors that impact the fleet's competitiveness, offering valuable insights for fleet managers and policymakers to meet carbon footprint reductions in a cost-effectively way.

Rapid increase in urbanization and industrialization due to increase in human population has led to increase in global warming resulting to climate change that affects the ecosystem. Unusual natural disasters such as cyclones, storms, floods, weather fluctuations, rising seal levels, transitional ecosystems and coastal disruptions are major adverse effects of climate change. There are huge worrisome concerns and uncertainties about the future of the planet earth due to climate change caused by high carbon emissions. Global aggressive policies in control of Carbon-dioxide (CO2) emissions from several combustion mechanisms have paved way for alternative/ clean energy sources. Green hydrogen is a promising means of clean energy sources for commercial power generation stations and other crucial systems such as hydrogen fuel cell vehicles (HFCVs) , motors, drives, backup power for buildings, and also serving as a source of electrical energy for remote locations. The goal of this study is to review the current level of Sub-Saharan African nations’ preparedness to adopt green hydrogen as a way to mitigate local energy supply issues and strengthen their individual economies.

Distracted driving is the leading cause of accidents, the cause of these distractions may include drowsiness, using cell phone, smoking a cigarette, etc. The proposed paper aims at monitoring the attentiveness of the driver and alerting the driver when his/her alertness goes below a certain threshold. It uses image processing using OpenCV (Computer Vision) and You Look Only Once (YOLO) algorithm to detect the eyes and object respectively and sounds an alarm when the driver is either drowsy or using his cell phone or smoking a cigarette.

Electric vehicles (EV) are getting more commonplace in the transportation sector in recent times. As the present trend suggests, this mode of transport is likely to replace the internal combustion engine (ICE) vehicles in near future. Each of the main EV components has a number of technologies that are currently in use or can become prominent in the future. EVs can cause significant impacts on the environment, power system, and other related sectors. The present power system can face huge instabilities with enough EV penetration; but with proper management and coordination, EVs can be turned into a major contributor to the successful implementation of smart grid. There are possibilities of immense environmental benefits as well, as the EVs can extensively reduce the greenhouse gas emission from the transportation sector. However, there are some major obstacles for EVs to overcome before replacing the ICE vehicles totally. This paper is focused on reviewing all the useful data available on EV configurations, energy sources, motors, charging techniques, optimization techniques, impacts, trends, and possible directions of future developments. Its objective is to provide an overall picture of the current EV technology and ways of future development to assist in future researches in this sector.

The aim of this study is to investigate transient dynamic flow characteristics of the fluid flow through 5-way electric coolant valve (PCCV : Penta-Control Coolant Valve). To achieve this goal, the present paper attempts the three-dimensional dynamic simulation of the fluid flow through the valve using a commercial CFD solver with moving mesh technique to consider flow inertia and dynamic flow in the opening and closing stages of the ball valve rotating motion. Firstly, dynamic flow characteristics and the thermal mixing inside the PCCV ball valve during the opening and closing stage was analyzed. It is found that the discrepancies between dynamic and steady state simulation is remarkable when fluxes with different levels of enthalpy and momentum flow into the PCCV leads to strong flow interference and flow inertia, while the discrepancies are relatively small at low rotation speed and weak flow interference. Then, the effect of dynamic flow characteristics of the valve on dynamic thermal mixing characteristics at two different ball valve rotational speeds and rotational directions were investigated. It was found that the dynamic flow and thermal mixing characteristics inside the PCCV are greatly affected by the rotation speed, rotation direction, and degree of flow interference between fluxes. It is helpful for the design of the better coolant control strategies and the improvement of the FCEV thermal management system.