Uncertainties in initial water saturation and early water breakthroughs of un-known sources and paths, which occurred in the low resistivity Lower Haushi sand-stone (LHS) reservoir at the beginning of oil production, imply that the bypassed oil can yet remain in the reservoir. In addition, the upper part of LHS is a tight oil reser-voir, which can still contain a significant amount of unrecovered oil. This opens the opportunity to produce the remaining oil instead of abandoning this reservoir. Low resistivity can exaggerate water saturation, leading to misinterpretation and premature water flooding due to inadequate oil-water contrast. Our analysis revealed a correlation between low resistivity and robust porous network connectivity, along-side elevated formation water salinity in highly porous layers. In regions of high po-rosity, sufficient oil-water contrast facilitates precise water saturation determination, affirming oil presence in all wells. However, within tight oil zones, near-complete wa-ter saturation contradicts actual oil presence. Factors contributing to saturation un-certainty and water breakthroughs were reassessed. Utilizing a 1:1 verti-cal-to-horizontal permeability ratio derived from core data enhanced simulation alignment with water production rates. Investigation into the impact of relative per-meabilities on water production was conducted. Water saturation maps were gener-ated to pinpoint remaining oil reserves. Depletion around wells is evident in lower po-rous regions, while oil persists across the entire tight reservoir, notably in two unex-plored sections.

Use of Machine Learning (ML) methodologies in optical communications has paved a new pathway. In this paper, firstly, we discuss the use of ML methodologies for reducing optical fiber nonlinearities, nonlinearity compensation, fault detection and optical performance monitoring. Then we present our recent work where we compare RL-SARSA and SVM based method with conventional method. The results show that RL-SARSA and SVM methods are successful candidates in mitigating the nonlinearities in proposed system as compared to conventional optical communication system.

We propose a 10-Gb/s 64-quadrature amplitude modulation (QAM) signal-based Radio over Fiber (RoF) system for 50 km of standard single mode fiber length which utilizes Reinforcement Learning (RL) SARSA based decision method to indicate an effective decision which mitigates nonlinearity. By utilizing RL-SARSA algorithm, the results demonstrate that significant reduction can be obtained in terms of bit error rate.

Machine learning (ML) methodologies have been looked upon recently as a potential candidate for mitigating nonlinearity issues in optical communications. In this paper, we experimentally demonstrate a 40-Gb/s 256-quadrature amplitude modulation (QAM) signal-based Radio over Fiber (RoF) system for 50 km of standard single mode fiber length which utilizes support vector machine (SVM) decision method to indicate an effective nonlinearity mitigation. The influence of different impairments in the system is evaluated that includes the influences of Mach-Zehnder Modulator nonlinearities, in-phase and quadrature phase skew of the modulator. By utilizing SVM, the results demonstrated in terms of bit error rate and eye linearity suggest that impairments are significantly reduced and licit input signal power span of 5dBs is enlarged to 15 dBs.

This article will provide an overview on internet of things (IoT), 5G communication System and Distributed Clouds. The basic concepts and benefits will be briefly presented, along with current standardization activities. In a nutshell, but the research will focus on relating internet of things, 5G and Distributed Cloud Computing.

This paper investigates how Islamic tolerance contributes to solve religious conflict today that has impacted on various aspects such as economic collapse, insecurity in life, lack of professional society, academic retrogressions, and so on. Knowledge of these issues has become an urgent to build a community that is full of peace, harmony and unity. The paper suggests that Quranic views on tolerance should be understood and practiced in order to avoid disunity in society which is due to failure to appreciate tolerance values in association. The paper concludes problems or misunderstandings always occur in different religious societies, since every religion has its own teachings and principles, as well as each of them is interpreted in different ways.

Measuring pulmonary nodules accurately can help with early diagnosis of lung cancer, which can improve a patient’s chances of survival. Many methods for segmenting nodules have been developed, but they all rely on input from radiologists in the form of a 3D volume of interest (VOI) or use a constant region of interest (ROI) and only consider the presence of nodule within the given VOI. These approaches limit the networks’ ability to detect nodules outside the given VOI and can also include unnecessary structures in the VOI, leading to potentially inaccurate segmentation. In this work, we propose a novel approach for 3D lung nodule segmentation by using 2D region of interest (ROI) inputted from radiologist or computer-aided detection (CADe) system. Particularly, we design a dual-encoder-based hard attention network (DEHA-Net) which incorporates the full slice of thoracic computed tomography scan along with the ROI mask to produce an accurate segmentation mask of lung nodule in the given slice. The proposed architecture exploits the adaptive region of interest (A-ROI) algorithm to automatically investigates the penetration of lung nodule into surrounding slices while eliminating the need to drawing separate ROIs in each slice. Further, the framework performs the multi-view analysis, i.e., in sagittal and coronal views, to improve the segmentation performance. The proposed scheme has been rigorously evaluated on the lung image database consortium and image database resource initiative (LIDC/IDRI) dataset and an extensive analysis of results have been performed. The quantitative analysis shows that the proposed method not only improves the existing state-of-the-art in term of dice score but also, significantly robust against the different types, shape and dimensions of lung nodules.

The recently emerged severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) caused a major outbreak of coronavirus disease 2019 (COVID-19) and instigated a widespread fear and has threatened global health security. Although phenomenal efforts are in progress to effectively combat this COVID-19 outbreak. Still, no licensed antiviral drugs or vaccines are available, and treatment is limited to supportive care and few repurposed drugs. In this urgency situation, computational drug discovery methods provide both an alternative and a supplement to tiresome high-throughput screening, particularly in the hit-to-lead-optimization stage. Identification of small molecules that specifically target viral replication apparatus has shown the most successful strategy in antiviral drug discovery. The present study deals with the identification of potential compounds that specifically interact with SARS-CoV-2 vital proteins, including main protease (Mpro), Nsp12 RNA-dependent-RNA-polymerase (RdRp) and Nsp13 helicase. A constructive and integrated virtual screening efforts together with molecular dynamics simulations identified potential binding modes and favourable molecular interaction profile of corresponding compounds. Moreover, structurally important binding site residues in conserved motifs located inside the active site are elucidated, which displayed relative importance in ligand binding based on residual energy decomposition analysis. Although the current study lacks experimental validation, the structural information obtained from this computational study paved the way to identify and design specific targeted inhibitors to combat COVID-19 outbreak.

In Sub-Saharan African Countries such as Nigeria with high prevalence rate, Child HIV/AIDs acquired through Mother-to-Child transmission (MTCT) can be largely prevented by using a well-established prevention programme and scheme. This study examined factors that can enhanced Prevention of Mother-to-Child transmission (PMTCT) in Nasarawa State. To achieve this, structured questionnaire were used to collect data from one hundred and sixteen (116) women attending two (2) primary facilities and two (2) secondary facilities in the State. This study utilized methods of Poisson Regression, Negative Binomial Regression and Logistic Regression Analyses. Results revealed that women with at least a secondary school education, women with husband in military and women with perceived confidentiality of their HIV status significantly enhanced PMTCT of HIV in Nasarawa State while significant proportion of the women attest to the fact that drugs are available in the facilities (p-value=0.0000<0.05) . Other factors include mother income level, willingness to continue with PMTCT programme and women in support group can also enhanced PMTCT though they are not significant. This study recommends that the factors identified should be explored by NGOs, Ministry of Health and, Support groups and other relevant agencies since they have the capacity to enhanced PMTCT of HIV in Nasarawa State, Nigeria.

Agricultural intensification has been adopted as a viable option for Poverty eradication and hunger, attainment of food security, socio-economic wellbeing as well as sustainable livelihood across the West Africa sub-humid and semi-arid zones. Thus, there is need to identify and address the challenges of sustainable livelihoods in the agriculture-intensive semi-arid and dry sub-humid zones of West Africa. This was addressed through review of relevant literature and analysis of environmental parameters from recent research by the authors to unveil the environmental uncertainties that threaten the sustainability of agriculture and human livelihoods across the ecologically fragile regions of West Africa, using pointers from Nigeria. The research identified the fundamental challenges, adaptation and mitigation approaches to environmental constraints, and requirements for reducing risk, enhance agricultural resilience as well as livelihoods in the zones. This was based on the premise that primarily, the use of adequate and accurately derived environmental information is crucial for increased agricultural productivity, sustainability of economic diversification and human livelihoods and by implication, enhanced regional and national security.

The contemporary landscape of eHealth is characterized by major concerns related to electronic medical records (EMRs). In an EMR, critical patient health information gets its own repository, which is the core of the eHealth system. Notably, the EMR not only retrieves health information generated in ambulatory clinical settings but also includes court-generated records. These overlapping records assume the role of a foundational data source for a comprehensive electronic health record (EHR). This scholarly review sheds light on recent trends in medical records and associated challenges, while at the same time providing insights into Saudi Arabia’s targeted approaches to healthcare delivery. Additionally, the talk expands to include a description of blockchain technology and its underlying conceptual framework. This demonstration positions blockchain technology as a promising approach that requires consideration for future use in the healthcare system.

Recently there is a growing concern regarding potential health hazards linked with 5G deployment and radio frequency emitted by these stations. It becomes fundamentally important to scientifically address these concerns. In this paper, the health risks incorporated with 5G are discussed critically in the light of scientific work and debunk these tittle-tattles where required. We confute scientifically the “5G appeal”, discuss effects of 5G on health, its implications on privacy, pandemics, ecosystem and role of world health organization in fighting these narratives. Finally, we provide future direction to negate these false claims linked with 5G.

Patients satisfaction with fast and high-quality services is the most important in the healthcare settings and specially in outpatient departments and private clinics. High quality services on health sector are indicated by continuous quality improvement (CQI). CQI is a progressive incremental process focused on safety of all participants, outcomes, systematic process, regulated and improved working environment at the later than earlier stages. Among the various suggested strategies, we adopted the patents feedback to improve the quality of services our clinic. All of the patient visited hospital were sent a massage on mobile and requested to provide their feedback on our services. Roughly around 5% of all visitors responded and filled up questionnaire. Majority of them were satisfied with the services in various department. However, they provided us some suggestions to identify the further gaps and improve the services in improving patients experience at our clinic. We considered their feedback, identified problems, redesigned the policies and implemented. After implementation of new strategies, we preliminary again evaluated the patients’ feedback on our services. Patients feedback explores that optimized methods of services for the has considerably increased the patients’ satisfaction. Taken together, our this shows that patients’ feedback is very important factor to improve patients’ experience at outpatient clinics using continuous quality improvement tools. For that reason, this study would serve as reference for public health stack holders, administrators and researchers.

In this work, quiescence is added to the Susceptible-Infectious-Recovered (SIR) model with demography. In order to investigate consequences of quiescence in the infection process in more depth, we use stochastic simulations on the stochastic version of model that we built. This method provides a more accurate picture of the dynamics of infectious diseases by taking into consideration the inherent randomness in the disease processes. We examine the effects of quiescence on the number of infected people using simulations. The results, presented in histograms depicting the distribution of infected individuals, reveal a notable trend: the mean number of infected individuals is higher when quiescence is incorporated into the dynamics. These finding emphasizes the dynamic influence of quiescence on infectious disease spread. The higher mean number of infections during periods of quiescence highlights the need for public health strategies that are flexible enough to focused interventions during these times to reduce the possibility of an increase in infections.

A Zn(II) perchlorate complex has been prepared and characterized by single X-ray crystallography, nuclear magnetic resonance spectroscopy, thermogravimetric analysis, infrared spectroscopy, elemental analysis, and UV-vis spectroscopy. The complex crystallizes in the monoclinic space group P21/c (Z = 4) with a pentacoordinated zinc center. Interestingly, the Zn complex was found be to a potential fluorophore that could sense acetone and other ketones with high selectivity and sensitivity.

The stability between the limited available energy resources and their consumption is an important concern of the modern world. The study deals with the development of the methods for measuring the energy performance of different renewable and non-renewable resources used for electricity generation with the help of an energy performance indicator called the Primary Energy Factor (PEF). This study takes account of all energy stages from the resources extraction to its transportation, conversion, combustion and then finally to utilization. The study conducted a comparative approach to calculate the PEF values of electricity generated in South Korea from the period of 1980 to 2017. Four different methodologies namely Eurostat methodology, Life cycle methodology, Modified Eurostat methodology, and upper-end methodology have been used. A set of Programs has been written in MATLAB to calculate the i. PEF values of electricity generated. ii. Impact of different renewable and non-renewable energy sources on PEF values. iii. Future trend of PEF values of electricity in South Korea At the national and local level, this study will help the government and other law-making institutions to make policies regarding annual purchase consumptions of energies by different industrial, residential, public and transportation sectors and at the Global level, the implementation of this study will be the catastrophe of maintaining the stability between the available energy resources, and consumptions. This, in turn, will lead to suitable living conditions for future generations

In this paper, we discuss voltage control method for buck converter operating in continuous conduction mode (CCM) using analog feedback system. The aim of this work is to control the output voltage of a buck converter during the variation in load current. This is obtained using analog feedback made with operational amplifier (Opamp). However, the same technique can be applied to other DC-DC converters (e.g boost, buck-boost, cuk converter, etc) in CCM mode, but for the purpose of analysis buck converter is chosen as an example.

In recent years, there has been a growing interest in the prediction of facial age due to its diverse applications in fields such as security, entertainment, and healthcare. The current scourge of underaged voting in Nigeria is a problem and this research delves into the realm of facial age prediction by employing four well-known convolutional neural network (CNN) architectures, namely VGG16, ResNet50, Mobile Net, and VGG19 to predict chronological ages from facial pictures of person. The objective is to achieve precise age estimation from facial images, utilizing two datasets: UTKFace and CASIA African Facial Datasets. The results of this investigation are noteworthy. Specifically, the VGG16 model which demonstrated remarkable performance, yielding a Mean Absolute Error (MAE) of 1.76 when applied to the UTK-Face dataset. Additionally, when utilizing Mobile-Net, an unprecedented MAE of 1.10 was achieved for the Casia Africa Face Dataset. Notably, this marks the first instance of employing the dataset for facial age detection with CNNs, and this approach outperformed previous works, yielding the lowest MAE among all the studies reviewed.

Hyperlipidemia is an identified risk factor for metabolic syndrome, obesity and cardiovascular complications characterized by elevated levels of lipids in blood. The present study aimed to inhibit HMG-CoA reductase with 15-oxoursolic acid through in-vivo and in-silico assessments. HFD-induced hyperlipidemia in rats was developed with a marked increase in total cholesterol (58.34 ± 0.21 mg/dl), triglycerides (45.45 ± 0.39 mg/dl), LDL-c (66.12 ± 0.10 mg/dl), VLDL-c (19.34 ± 0.16 mg/dl), and a decrease in HDL-c (10.34 ± 0.18 mg/dl). The oral administration of 15-oxoursolic acid at a concentration of 30 mg/Kg b.w significantly reduced the serum concentration of total cholesterol (42.65 ± 0.54 mg/dl), triglycerides (32.33 ± 0.16 mg/dl), LDL-c (50.34 ± 0.15 mg/dl) and VLDL-c (13.15 ± 0.45 mg/dl) respectively and an increased in the serum HDL-c (18.56 ± 0.34 mg/dl). 15-oxo ursolic acid also caused a decrease in the coronary risk index and atherogenic risk index. In-silico studies of 15-oxoursolic acid with HMG-CoA reductase showed significant interaction capability with binding energy (-9.26805 Kcal/mol). It is concluded that 15-oxoursolic acid could significantly reduce the total cholesterol, triglycerides and LDL levels in HFD-induced hyperlipidemia rats which might lead to new medication with significant hypolipidemic potential.

Historically, the lack of comprehensive and real-time data is the main challenge in city sustainability assessments. However, with the increase in the availability of crowdsourced data over the last decade, a rich and real-time data source provides detailed images of urban systems. This has opened up new opportunities for practitioners, including geographers, social researchers, and data scientists, to gather and utilize social media data as a core source for studying cities and assessing their sustainability. This paper proposes an assessment model for the sustainability of cities based on crowdsourced data and the principles of General System Theory. The model aims to utilize crowdsourced data for the analysis and decision-making processes to enhance the sustainability and resilience of smart future cities.

While visual assessment is the standard technique for burn evaluation, computer-aided diagnosis is increasingly sought due to high number of incidences globally. Patients are increasingly facing challenges which are not limited to shortage of experienced clinicians, lack of accessibility to healthcare facilities, and high diagnostic cost. Certain number of studies were proposed in discriminating burn and healthy skin using machine learning leaving a huge and important gap unaddressed; whether burns and related skin injuries can be effectively discriminated using machine learning techniques. Therefore, we specifically use pre-trained deep learning models due to deficient dataset to train a new model from scratch. Experiments were extensively conducted using three state-of-the-art pre-trained deep learning models that includes ResNet50, ResNet101 and ResNet152 for image patterns extraction via two transfer learning strategies: fine-tuning approach where dense and classification layers were modified and trained with features extracted by base layers, and in the second approach support vector machine (SVM) was used to replace top-layers of the pre-trained models, trained using off-the-shelf features from the base layers. Our proposed approach records near perfect classification accuracy of approximately 99.9%.

Rapidly changing dynamics of globalization and increasing market competition are causing the companies all around the world confronting several new challenges and opportunities. To be competitive and successful apart from relative importance of physical resources, companies must adapt modern strategies and policies regarding market flexibility and development. The purpose of this study is to empirically investigate the relationship between intellectual capital and firm value. Furthermore, the moderating role of managerial ownership has been evaluated with the help of regression analysis. The sample included the panel data taken from non-financial firms listed on Pakistan stock exchange (PSX) covering the period 2010-2015. A sample of 79 firms out of 384 firms have been selected with the help of systematic sampling technique. VAIC (Value Added Intellectual Coefficient) model has been used for the calculation of intellectual capital. Tobin's Q has been taken as a measure of firm value. Managerial ownership has been tested as moderator. Based on data analysis, it is concluded that the relationship between intellectual capital and firm value is positively significant. It is also concluded that managerial ownership moderates the relationship between intellectual capital and firm value negatively.

For a graph G, let P(G, λ) be its chromatic polynomial. Two graphs G and H are said to be chromatically equivalent if P(G,λ) = P(H,λ). A graph is said to be chromatically unique if no other graph shares its chromatic polynomial. In this paper, chromatic polynomial of the necklace graph N_n, for n ≥ 2 has been determined. It is further shown that N₃ is chromatically unique.

Biotic stressors pose serious threats to crop yield, jeopardizing food security and resulting in over US$220 billion per year losses to the agriculture industry. Plants activate innate defense mechanisms upon pathogen perception and invasion. The plant immune response comprises numerous concerted steps, including the recognition of invading pathogens, signal transduction, and activation of defensive pathways. However, pathogens have evolved various structures to evade plant immunity. Given these facts, genetic improvements of plants are required for sustainable disease management to ensure global food security. Advanced genetic technologies have provided new opportunities to revolutionize and boost plant disease resistance against devastating pathogens. Furthermore, targeting susceptibility (S) genes, such as OsERF922 and BnWRKY70, through CRISPR methodologies offers novel frontiers to disrupt the molecular compatibility of pathogens and introduce durable resistance against them in plants. Here, we provide a critical overview of advances in understanding disease resistance mechanisms. The review also critically examines management strategies under challenging environmental conditions and R gene-based plant genome engineering systems intending to enhance plant responses against emerging pathogens. This work underscores the transformative potential of modern genetic engineering practices in revolutionizing plant health and crop disease management while emphasizing the importance of responsible application to ensure sustainable and resilient agricultural systems.

Big data has revolutionised science and technology leading to the transformation of our societies. High Performance Computing (HPC) provides the necessary computational power for big data analysis using artificial intelligence and methods. Traditionally HPC and big data had focused on different problem domains and had grown into two different ecosystems. Efforts have been underway for the last few years on bringing the best of both paradigms into HPC and big converged architectures. Designing HPC and big data converged systems is a hard task requiring careful placement of data, analytics, and other computational tasks such that the desired performance is achieved with the least amount of resources. Energy efficiency has become the biggest hurdle in the realisation of HPC, big data, and converged systems capable of delivering exascale and beyond performance. Data locality is a key parameter of HPDA system design as moving even a byte costs heavily both in time and energy with an increase in the size of the system. Performance in terms of time and energy are the most important factors for users, particularly energy, due to it being the major hurdle in high performance system design and the increasing focus on green energy systems due to environmental sustainability. Data locality is a broad term that encapsulates different aspects including bringing computations to data, minimizing data movement by efficient exploitation of cache hierarchies, reducing intra- and inter-node communications, locality-aware process and thread mapping, and in-situ and in-transit data analysis. This paper provides an extensive review of the cutting-edge on data locality in HPC, big data, and converged systems. We review the literature on data locality in HPC, big data, and converged environments and discuss challenges, opportunities, and future directions. Subsequently, using the knowledge gained from this extensive review, we propose a system architecture for future HPC and big data converged systems. To the best of our knowledge, there is no such review on data locality in converged HPC and big data systems.

: Background: Pseudomonas aeruginosa is an opportunistic pathogen involved in number of hospital acquired infections such as catheter-associated urinary tract infections, bacteremia, septicemia, skin infections and ventilator-associated pneumoniae. Biofilm formation is an important trait implicated in chronic infections, such as cystic fibrosis and chromic pulmonary obstruction. Method: A total of 266 isolates were collected from the Armed Forces Institute of Pathology (AFIP). Antibiotic susceptibility was assessed by double disk synergy testing. ESBL and Modified Hodge testing was performed for phenotypic confirmation of carbapenemases. Molecular screening of the genes was done by PCR. Micro-dilution broth method was used to determine minimum inhibitory concentrations of antibiotics. Biofilm formation was done by micro-titer plate assay. Results: Overall, 20% of the P. aeruginosa isolates were extensively drug resistant (XDR-PA) and 25% were multi-drug-resistant (MDR-PA). Likewise, 43% of the isolates were ESBL producers and carbapenemase production was detected in 40% of the isolates. Molecular analysis confirmed occurrence of different resistant factors in ESBL positive isolates; 67% carried bla-TEM, 62% bla-CTXM-15, 41% bla-SHV, 34% bla-CTXM-14 and 33% bla-OXA-1. In addition, 68% of carbapenem-resistant isolates were positive for bla-NDM-1, 25% for bla-OXA-48 and 22% for bla-KPC-2. Biofilm formation was tested for 234 isolates, out of which 28% were strong biofilm formers. Moderate and weak biofilm formers were 46% and 23% respectively. Overall, ciprofloxacin, levofloxacin and cefepime showed inhibitory effects on P. aeruginosa biofilms. Antibiotics in combination showed strong synergistic effects (ciprofloxacin &amp; cefepime); while gentamicin and cefepime resulted into complete eradication of P. aeruginosa biofilm. Conclusion: We confirm strong synergistic effects of gentamicin and cefepime that completely eradicated P. aeruginosa biofilm. We further confirm inhibitory effects of ciprofloxacin, levofloxacin and cefepime on P. aeruginosa biofilms.

Coronavirus disease 2019 (COVID-19), the emissary behind the worst global pandemic of the 21st century, is primarily a respiratory disease-causing virus called SARS-CoV-2 which is responsible for millions of new cases (incidence) and deaths (mortalities), worldwide. Many factors have played a role in the differential morbidity and mortality experienced by nations and ethnicities against SARS-CoV-2, such as the quality of primary medical health facilities or enabling economies. Nevertheless, the most important variable, i.e., the subsequent ability of individuals to be immunologically sensitive or resistant to the infection, was not properly discussed before. Therefore, an astounding issue arose when some developed countries experienced higher morbidity and mortality, compared with their relatively underdeveloped counterparts, despite having excellent medical health facilities. Hence this investigative review attempts to analyze the issue from an angle of previously undiscussed genetic, epigenetic, and molecular immune resistance mechanisms in correlation with the pathophysiology of SARS-CoV-2 and varied ethnicity-based immunological responses against it. The biological factors discussed here include the overall landscape of human microbiota, endogenous retroviral genes spliced into the human genome, copy number variation, and how they could modulate the innate and adaptive immune systems, which put a particular ethnic genetic architecture at a higher risk of SARS-CoV-2 infection than others. Considering an array of these factors in their entirety may help explain the geographic disparity of disease incidence, severity, and subsequent mortality associated with the disease while at the same time encouraging scientists to design new experimental approaches to investigation.

The ubiquitin-specific protease 2 (USP) belongs to the family of deubiquitinases and plays a critical role in tumors cells’ survival and therefore signifies an important therapeutic target. Previous studies have indicated promising efficacies of potent human USP2 inhibitors including, thiopurine analogues against SARS-CoV papain-like proteases (PLpro). The PLpro have significant functional implications in the innate immune response during SARS-CoV-2 infection and considered an important antiviral target. Both proteases share strikingly similar USP fold with right-handed thumb–palm–fingers structural scaffold and conserved catalytic triad Cys-His-Asp/Asn. In this urgency situation of COVID-19 outbreak, there is a lack of in-vitro facilities readily available to test SARS-CoV-2 inhibitors in whole-cell assays. Therefore, we adopted an alternate route to identify potential USP2 inhibitor through integrated structure-based virtual screening efforts. After a subsequent virtual screening protocol, the best compounds were selected and tested. The compound Z93 showed significant IC₅₀ value against Jurkat (9.67 µM) and MOTL-4 cells (11.8 µM). The binding mode of Z93 was extensively analyzed through molecular docking, followed by MD simulations, and molecular interactions were compared with SARS-CoV-2. The relative binding poses of Z93 fitted well in the binding site of both proteases and showed consensus π-π stacking and H-bond interactions with histidine and aspartate/asparagine residues of the catalytic triad. These results led us to speculate that compound Z93 might be the first potential chemical lead against SARS-CoV-2 PLpro, which warrants in-vitro evaluations.

Nowadays, emerging technologies have changed the places of work through computers and ICT tools, which have revolutionized teaching and learning environments in different ways. In spite of the fact that computers as ICT tools have become part and progressively instrument for teachers and instructors used in teaching and learning, but most educators can't incorporate them into their teaching and learning process, which results in students being ill-equipped or lacking some necessary skills in the world of work, which leads to low performance and poor handling of tools whose lead to low production. To tackle this issue, it is essential to develop the technical and vocational education and training (TVET) system by determining the quality of technical and vocational education (TVE) teachers. In this paper, the literature concerning the competence required by TVET teachers towards computer-related instructional tech-nology for classroom teaching and learning was examined through the technological pedagogical content knowledge (TPACK) model. Sixty (60) questionnaires were ad-ministered to TVE teachers within six technical colleges of education in north-eastern Nigeria. The data was quantitatively analyzed using traditional linear models, namely multilinear regression (MLR) and artificial intelligence (AI) models, namely artificial neural networks (ANN) and adaptive neuro-fuzzy inference systems (ANFIS), which were developed using MATLAB 9.3 (R2019a), while the classical linear MLR model was developed using SPSS software. The results from our classical study indicated that TVE teachers are competent in computer and some instructional technology usage and show a high correlation between competence and teaching experience and a lower correlation between competence and gender. The goodness of fit shows a good fit of the model. Future studies should examine the application of other linear and non-linear AI techniques.

Background: The incidences of COVID-19 related suicide among adolescents and youths have been reported across the world. There is no cumulative study focusing on nature, patterns, and causative factors that lead to the present investigation. Methods: A purposive sampling of google news between 15 February to 6 July was performed. After excluding duplicate reports, the final list comprised a total of 37-suicide cases across 11 countries. Results: More male suicides were reported (21-cases, i.e., 56.76%), and the mean age of the total victims was 16.6±2.7 years (out of a total of 29-cases). About two-thirds of the suicides were from three countries named India (11-cases), United Kingdom (8-cases), and the USA (6-cases). Out of 23-student victims, 14 were school-going students. Hanging was the most common suicide method accounting in 51.4% of cases. The most common suicide causalities were related to mental sufferings such as depression, loneliness, psychological distress, etc., whereas either online schooling or overwhelming academic distress was placed as the second most risk factors followed by TikTok addiction-related psychological distress, and tested with COVID-19. Conclusion: The finding of the temporal distribution of suicides concerning lockdowns may help in exploring and evolving public measures to prevent/decrease pandemic-related suicides in young people.

The Kabul River basin (KRB) of Afghanistan, a lifeline of around 10 million people, has multiplicity of governance, management and development related challenges leading to inequity, inadequacy and unreliability of irrigation water distribution. Prior to any uplifting intervention, there is a need to evaluate the performance of irrigation system on long term basis to identify the existing bottlenecks. Although there are several indicators used for the performance evaluation of the irrigation schemes, but we used the coefficient of variation (CV) of actual evapotranspiration (ETa) in space (basin, sub-basin, and provincial level), relative evapotranspiration (RET) and temporal CV of RET to assess the equity, adequacy and reliability of water distribution respectively, from 2003 to 2013. The ETa was estimated through surface energy balance system (SEBS) algorithm and the ETa estimates were validated using advection aridity (AA) method with R2 value of 0.81 and 0.77 at Nawabad and Sultanpur stations respectively. The global land data assimilation system (GLDAS) and moderate-resolution imaging spectroradiometer (MODIS) products were used as main inputs to the SEBS. Results show that mean seasonal sub-based RET values during summer (May – September) (0.37 ± 0.06) and winter (October – April) (0.40 ± 0.08) are below the target values (RET ≥0.75) during 2003-2013. The CV of mean ETa within sub-basins and provinces for the entire study period has equitable distribution of water from October-January (0.09±0.04) whereas the highest inequity (0.24±0.08) in water distribution is during early summer. The range of the CV of mean ETa (0.04-0.06) on monthly and seasonal basis shows the unreliability of water supplies in several provinces or sub-basins. The analysis of temporal CV of mean RET highlights unreliable water supplies across the entire basin. The maximum ETa during the study period was estimated for Shamal sub-basin (552±43mm) while among provinces Kunar experienced the highest ETa (544±39mm). This study highlights the dire need for interventions to improve the irrigation performance in time and space. The proposed methodology can be used as a framework for monitoring and implementing the water distribution plans in future.

The extended finite element method (XFEM) is now widely used in crack simulations and the direction of propagation of the XFEM crack in SS-304 has been quite interesting. This paper discusses the direction,θ(+ve in anti-clockwise direction), of the XFEM crack (under mode-I) propagation based on the von Mises stress-field around the crack-tip for static loading under the light water reactors (LWRs) conditions. The Mises core region from the crack-tip is chosen for β=〖90〗^o, the angle between the load and the initial crack. Experimental data for LWRs’environment is obtained and the simulations have been carried out applying three different static loads and results for the direction of the crack are calculated by measuring the stress-field around the crack-tip. It has been found that the direction of the XFEM varies inversely as the stress-field around the crack tip is increased. The computational results have been compared with the numerical results based on the minimum strain energy density criterion[S-criterion].

The technical capabilities of modern Industry 4.0 and Industry 5.0 are rather vast and growing exponentially daily. The present-day Industrial Internet of Things (IIoT) combines manifold underlying technologies that require real-time interconnections and communications among heterogeneous devices. Smart cities are established with sophisticated designs and control for seamless Machine-to-Machine (M2M) communication to optimize resources, costs, performances, and energy distribution. All the sensory devices within a building interact to maintain a sustainable climate for residents and intuitively optimize the energy distribution to optimize energy production. However, it encompasses quite a few challenges for devices that lack compatible and interoperable designs. Conventional solutions are restricted to limited domains or rely on engineers to design and deploy translators for each pair of ontologies. This is a costly process in terms of engineering efforts and computational resources. The issue persists that a new device with a different ontology must be integrated into an existing IoT network. We propose a self-learning model that can determine the taxonomy of devices given their ontology meta-data and structural information. The model finds matches between two distinct ontologies using the Natural Language Processing (NLP) approach for learning linguistic contexts. Then, by visualizing the ontology network as a knowledge graph, it is possible to learn the structure of the meta-data and understand the device's message formulation. Finally, it can align entities of both ontology graphs similar in context and structure. Furthermore, the model performs dynamic M2M translation without requiring extra engineering or hardware efforts.

Fine-grained image classification remains an ongoing challenge in the computer vision field, which is particularly intended to identify objects within sub-categories. It is a difficult task since there is a minimal and substantial intra-class variance. The current methods address the issue by first locating selective regions with Region Proposal Networks (RPN), object localization, or part localization, followed by implementing a CNN Network or SVM classifier to those selective regions. This approach, however, makes the process simple by implementing a single-stage end-to-end feature encoding with a localization method, which leads to improved feature representations of individual tokens/regions by integrating the transformer encoder blocks into the Yolov5 backbone structure. These Transformer Encoder Blocks, with their self-attention mechanism, effectively captured the global dependencies and enabled the model to learn relationships between distant regions. This improved the model ability to understand context and captured long-range spatial relationships in the image. We also replaced the Yolov5 detection heads with three transformer heads at the output for object recognition using the discriminative and informative features maps from transformer encoder blocks. We established the potential of the single stage detector for the fine-grained image recognition task, by achieving state of the art 93.4% accuracy, as well as outperforming the existing Yolov5 model. The effectiveness of our approach is assessed using the Stanford car dataset, which includes 16,185 images of 196 different classes of vehicles with significantly identical visual appearances.

Chatbots are extensively needed in customer services to handle customer inquiries, such as tracking orders or providing information about products and services. One of the most reliable implementations of chatbots is using the common architectures of LSTM networks named Seq2Seq networks. The networks are using an encoder and a decoder. Seq2Seq chatbot is a type of chat system that is professional enough to pass the Turing test. The Turing test is a way of deciding the accuracy of the machine by examining its response, it should appear like a human response. In this research, we will introduce a novel architecture that can pass the Turing test. The seq2seq Accuracy is improved by making incremental training to the chatbot. The new proposal provides higher accuracy and high similarity to human chat responses.

Providing healthcare workers with cost information about the medications they prescribe can influence their decisions, particularly when that information is provided at the very moment they are faced with a prescribing decision. The current study aimed to analyse the impact of nudges that presented cost information to prescribers through their organisation's electronic prescribing system. The nudges were co-created by the research team (composed of behavioural scientists) and the lead hospital pharmacist. One nudge provided simple cost information (percentage difference between two brands of Mesalazine – Asacol and Octasa). The second nudge provided the potential annual cost-saving that could result if the cheaper medication was selected across the organisation. While the statistical analyses revealed that these nudges were not effective, several administrative barriers were overcome, which may inform future research. For example, presenting aggregated cost information to the prescribers is possible even when the actual cost of medicine is confidential and can not be displaced. In addition, future research could reveal more behavioural factors that facilitate medication optimisation.

Type 2 Diabetes (T2D) is a growing global health problem that requires new and effective prevention and management strategies. Recent research has highlighted the role of epigenetic changes in the development and progression of T2D, and the potential of functional foods as complementary therapy for the disease. This review aims to provide an overview of the current state of knowledge on the preventive epigenetic mechanisms of functional foods in T2D. We provide background information on T2D and its current treatment approaches, an explanation of the concept of epigenetics, and an overview of the different functional foods with demonstrated preventive epigenetic effects in T2D. We also discuss the epigenetic mechanisms by which these functional foods prevent or manage T2D and the studies that have investigated their preventive epigenetic effects. In addition, we revisit works on the beneficial influence of functional foods against the programming and complications of parentally-triggered offspring diabetes. We also postulate, albeit based on the scarce data, that epigenetic inheritance mechanistically mediates the impacts of functional nutrition against the metabolic risk of diabetes in the offspring. Finally, our review highlights the importance of considering the preventive epigenetic mechanisms of functional foods as a potential avenue for the development of new prevention and management strategies for T2D.

The objective of this study was to compare the effect of different botanical powders and synthetic chemical in controlling Sitophilus zeamais in stored maize. A laboratory experiment was done to assess three botanicals, Zingiber officinale, Moringa oleifera, Xylopia aethiopica, in controlling the S. zeamais. The results of this study demonstrated the active potentials of these plant products as plant-derived insecticides against maize weevil. The synthetic chemical used showed both higher weevil mortality and higher grain loss than the botanicals (P< 0.05). The Botanicals also showed significance difference in the mortality rate (P < 0.05) as Z. officinale recorded the highest mortality rate (5.66%) while X. aethiopica recorded the lowest mortality rate (3.66%). The control attained the highest grain damage (7.33%) while amongst the botanicals, the highest was found in Z. officinale (7.33%) and lowest was on M. oliefera (5.33%). The exit holes made by the weevils at the end of the experiment were highest (2.66) in M. oliefera whereas lowest was recorded on X. aethiopica (1.00). Z. officinale, X. aethiopica and M. oleifera were efficacious against S. zeamais instead of synthetic chemical insecticides that have environmental health hazards and they can be used in integrated pest management by farmers and foods merchants. Therefore, since these botanicals have no any adverse effects on the seeds and safe to the environment, they are recommended for future usage in storage grains to control of S. zeamais.

The research aims to discover the natural occurrence of patulin (PAT) in selected citrus fruits from the central cities of Punjab and Pakistan's Northern cities. Total 2970 samples of twelve citrus fruits; kinnow, orange, grapefruits, bitter orange, mausami, red blood, pineapple, sweet orange, rough lime, sweet lime, kagzi lime and lemon were examined using liquid chromatography fitted with UV detector. The limit of detection (LOD) and quantification limit was 0.04 and 0.12 µg/kg, respectively. The results have shown that 56% of samples of citrus fruits from Punjab's central cities, Pakistan, were discovered to be infected from PAT. The elevated amounts of PAT ranging from 0.04 to 1150 µg/kg were found in citrus fruit samples from Multan cities. Furthermore, 31.7% of samples of citrus fruits from Northern cities of Pakistan were discovered to be infected with PAT, and the elevated amounts were found ranging from 0.04-320 µg/kg from Swat city. About 22.1% of samples of citrus fruits have levels of PAT greater than the suggested limits established by the European Union (EU). PAT's dietary intake levels ranged from 0.10-1.11 µg/kg bw/day from the central cities of Punjab, Pakistan, and 0.13-1.93 µg/kg bw/day were documented from Northern cities of Pakistan.

The objectives of the current research were to determine the levels of deoxynivalenol (DON) in four different cultivars of corn and subsequently to investigate the fate of DON during pro-cessing steps involved for the production of cornbread. The samples (n = 30) of each cultivar which were found positive were selected for the study. The average level of DON was ranged from LOD to 650 µg/kg. The amount of DON in cornflour samples were ranged from LOD to 630 µg/kg and insignificantly lower than the levels found in corn grain samples (p ≥ 0.05). Further-more, the levels of DON in corn dough samples were insignificantly higher than the levels in cornflour samples (p ≥ 0.05), with levels ranged from LOD to 645 µg/kg. However, the amount of DON in cornbread samples was significantly different from the levels found in corn grains sam-ples (p ≤ 0.05), with levels ranged from LOD to 611.5 µg/kg. The percentage reduction of DON in grains to cornbread samples was 22.4%, 35.6%, 44.5%, and 42.6% in type 1, type 2, type 3, and type 4 cultivars, respectively. The highest dietary exposure and hazard quotient (HQ) of DON was 0.13 and 0.17 µg/kg bw/d, in male and female individuals resulted from the consumption of cornbread samples, respectively.

The study focused on investigating the natural incidence of deoxynivalenol (DON) in corn and products from corn producing districts of Punjab, Pakistan. The analysis was carried out using HPLC with UV detector and immunoaffinity cleanup columns. The detection limit (LOD) and limit of quantification were 25 and 50 µg/kg, respectively. Total 1220 samples of corn and products were analyzed to detect the DON, and 539 (44.2%) samples were observed to be contaminated with DON (n ≥ LOD). Furthermore, 92 (7.5%) samples of corn & products have DON levels, elevated than the proposed limits of the EU. The data is significantly different from a normal distribution for DON in corn and products samples and from different locations (p < 0.05) for Shapiro-Wilk and Kolmogorov-Smirnov values. However, a significant difference in DON levels was found between corn and corn derived-products types (p ≤ 0.05). The lowest and highest exposure & hazard quotient (HQ) of 0.92 and 9.68 µg/kg bw/d were documented in cornflour samples.

Facial emotion detection is a challenging task that deals with emotion recognition. It has applications in various domains, such as behavior analysis, surveillance systems and human-computer interaction (HCI). Numerous studies have been implemented to detect emotions, including classical machine learning algorithms and advanced deep learning algorithms. For the machine learning algorithm, the hand-crafted feature needs to be extracted, which is a tiring task and requires human effort. Whereas in deep learning models, automated feature extraction is employed from samples. Therefore, in this study, we have proposed a novel and efficient deep learning model based on Neural Architecture Search Network utilizing superior artificial networks such as RNN and child networks. We performed the training utilizing the FER 2013 dataset comprising seven classes: happy, angry, neutral, sad, surprise, fear, and disgust. Furthermore, we analyzed the robustness of the proposed model on CK+ datasets and comparing with existing techniques. Due to the implication of reinforcement learning in the network, most representative features are extracted from the sample network. It extracts all key features without losing the key information. Our proposed model is based on one stage classifier and performs efficient classification. Our technique outperformed the existing models attaining an accuracy of 98.14%, recall of 97.57%, and precision of 97.84%.

Mechanochemical production of copper (II) isonicotinate Metal-Organic Framework ([Cu (INA)2]-MOF) and its modified magnetic iron composite ([Cu (INA)2]-MOF@Fe3O4]) allowed for the adsorptive removal of Terbutaline from water. A variety of characterization techniques, including Fourier, transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscopy (SEM), were used to elucidate the distinct chemical and morphological features of the two advanced materials. The optimal adsorption conditions were determined by investigating a wide range of adsorption-related variables, including contact time, initial Terbutaline concentration, adsorbent dosages pH, and temperature. The chemistry involved in the adsorption process between the adsorbents and the adsorbate molecules was evaluated using the best-fitting models, such as kinetics, isotherms, and thermodynamics, and the regeneration study was performed to evaluate the adsorbents' reusability. Incredibly maximum adsorption capacities (Qmax) of 1667 and 2500 mg L-1 were attained within 40 minutes under alkaline pH 11 by the [Cu (INA)2]-MOF and the [Cu (INA)2]-MOF@Fe3O4, respectively. The adsorbents have been proven to be good for the adsorption of Terbutaline as a priority pollutant in an aqueous solution, with pseudo-first order and Langmuir as the best-fitting models for the kinetic and isotherm models respectively.

A new class of tetrasubstituted imidazole based compounds was synthesized using a multicomponent one-pot synthesis scheme through a cyclo condensation reaction of benzil, aromatic primary amines, aldehydes and ammonium acetate in glacial acetic acid. The synthesized compounds have been analyzed and characterized by melting point, color, conductivity method, CHN analysis, FT-IR, and UV-Visible. The reaction proceeding was examined by TLC after regular intervals of period. To test biological activity, the synthesized compounds have been examined against various bacterial strains. From the analysis of the antibacterial activity of these synthesized compounds demonstrated that all three imidazole compounds have considerable to significant activity against the strains, and compound K2 was found potent comparatively.

Small modular reactors (SMR) (&lt;300 MW) offer a potentially attractive nuclear energy option for the middle-east region (MER). Currently, the MER uses a significant amount of fossil fuel to process heat applications such as water desalination and in petroleum refineries and chemical plants, besides generating electricity. SMR technologies represent an opportunity to meet future energy demand in the MER. This paper discusses issues related to the future development and use of SMR technology in nuclear-renewable hybrid energy systems for application in the middle east. SMRs have also been examined as part of a resilient hybrid energy system that combines nuclear energy with renewable energy and traditional fossil energy to produce chemicals, fuels, and electricity. This paper presents the results of a techno-economic analysis of a Nuclear-Renewable-Conventional Hybrid Energy System. The paper concludes that SMR technology will be an essential feature of future hybrid energy systems for the MER.

Salmonellosis is a bacterial zoonosis with array of health conditions. Non-typhoidal salmonellosis (NTS) have a discrete adaptation to certain animals; in poultry, pullorum and fowl typhoid are its primary disease manifestations. The diseases are prevalent in the Nigerian poultry and have been well studied in Nigeria, but less so in the north central Nigeria (NCN). Using field sampling, laboratory methods and semi structured questionnaire in 1000 poultry farms from NCN, we explore the incidence and risk factors for the persistence of NTS infection in poultry. Approximately 41.6% of the farms have experienced NTS but only 6.3% have current infection with NTS. Farm experience of NTS moderately predicted awareness of salmonellosis. Increasing stock in smallholder farms, self-mixing of concentrate on the farm, usage of stream water, pen odour, non-adherence and partial adherence of farms to recommended poultry vaccination against pullorum and fowl typhoid, and lack of and non-adherence to biosecurity were identified risk factors that increased the odds of NTS infection in poultry. Antibiotic use practice may have reduced the isolation rate of NTS, yet NTS continues to challenge poultry farms in Nigeria. Identified risk practices must be mitigated intentionally and biosecurity and hygiene must improve to reduce the burden of NTS.

Abstract: (1) Background: Minimally-invasive sacroiliac joint (SIJ) fusion is the preferred surgical intervention to treat chronically severe pain associated with SIJ degeneration and dysfunction. (2) Methods: This paper details the ten-step surgical procedure associated with the postero-inferior approach using the PsiF™DNA Sacroiliac Joint Fusion System. (3) Results: The posterior surgical approach with an inferior operative trajectory (postero-inferior) utilizes easily identifiable landmarks to provide the safest, most direct access to the articular joint space for transfixing device placement. Implanting the device through the subchondral bone, provides maximum fixation and stabilization of the joint by utilizing an optimal amount of cortical bone-implant interface. Approaching the joint from the inferior trajectory also places the implant perpendicular to the S1 endplate at a “pivot point” near the sacral axis of rotation, which addresses the most significant motion of the joint. (4) Conclusions: Further observational data from real-world clinical use are encouraged to further validate this procedure as the surgical preference for minimally-invasive SIJ fusion.

Mental stress is one of the serious factors that lead to many health problems. Scientists and physicians have developed various tools to assess the level of mental stress in its early stages. Several neuroimaging tools have been proposed in the literature to assess mental stress in the workplace. Electroencephalogram (EEG) signal is one important candidate because it contain rich information about mental states and condition. In this paper, we review the existing EEG signal analysis methods on the assessment of mental stress. The review highlights the critical differences between the research findings and argues that variations of the data analysis methods contribute to several contradictory results. The variations in results could be due to various factors including lack of standardized protocol, the brain region of interest, stressor type, experiment duration, proper EEG processing, feature extraction mechanism, and type of classifier. Therefore, the significant part related to mental stress recognition is choosing the most appropriate features. In particular, a complex and diverse range of EEG features, including time-varying, functional, and dynamic brain connections, requires integration of various methods to understand their associations with mental stress. Over this, the review suggests fusing the cortical activations with the connectivity network measures and deep learning approaches to improve the accuracy of mental stress level assessment.

Objective: The private healthcare providers (PHCP) are believed to improve access to healthcare services in Public-Private Mix (PPM) projects, as they are considered first point of contact for healthcare. The purpose of this study was to know the satisfaction level of TB patients. Design: A questionnaire-based, cross-sectional study was carried out during November and December 2017 for 572 under-treatment patients registered with PHCPs in the PPM project. Lot quality assurance sampling technique was used to randomly select 19 districts from sample frame of 75 districts. In each selected district, data collector retrieved TB register of 8 months (Jan – Aug 2017) and systematically selected patients by fixed periodic interval. SPSS (version 24.0) was used to analyze the data. Results: Study included 53% (n=301) of males and 47% (n=271) of females, with mean age of 38 years (SD, ±18). Almost half of the participants were illiterate (51%, n=289) and 64% (n=365) were non-earning members of the family. In practice, most of the participants visit private providers (71%, n=407), including private hospital/clinic (44%) and traditional practitioners (27%; n=153). 55% of participants visited the current doctor because of clinic’s proximity to residence. 82% of the participants (n=469) were satisfied with the TB care services and 85% (n=488) said that they would recommend this clinic to others. Conclusion: PHCPs are preferred providers for individuals, which is consistent with findings of other studies. Though they are satisfied with TB care and services, interventions should be introduced to reduce the financial burden on the patient. Partnering PHCP is a way forward to ensure universal health coverage, health system strengthening and better health outcomes of the population.

The paper discusses how joint damage and deterioration affect the seismic response of existing reinforced concrete frames with sub-standard beam-column joints. The available simplified modeling techniques are critically reviewed to propose a robust, yet computationally efficient technique for simulating the nonlinear behavior of substandard beam-column joints. Improvements over the existing models include simulation of the cyclic deterioration of joint stiffness and strength as well as pinching in the hysteretic response, implemented considering a deteriorating hysteretic rule. A fibre-section forced-based inelastic beam-column element is developed; considering improved material models and fixed-end rotation due to bond failure, rebars-slip and inelastic extension, to simulate the deteriorating cyclic behavior of existing pre-cracked beam-column members. For the assessment of frames with substandard exterior beam-column joints, a nonlinear model for the exterior joint is developed and validated through a full-scale quasi-static cyclic test performed on a substandard T-joint connection. The proposed model allows considering structural performance in risk assessment while accounting for true inelastic mechanisms at the joints.

Guava is a vital fruit worldwide, especially in Pakistan, and due to its nutritional value famous in each age group. Due to a very short shelf life, the marketing and export of this fruit faced severe constraints. Therefore, in the current study, edible coating of chitosan (0, 0.5, 1.0, 1.5, and 2.0%) was evaluated on postharvest shelf life when guava fruits were stored (room temperature and 4 °C temperatures) for 12 days. The chitosan treated coating fruits have shown reduced total sugars and malondialdehyde levels compared to untreated control samples. However, a significant difference (p ≤ 0.05) in total sugar and malondialdehyde levels exists between samples stored in m compared to refrigerated temperature (4 °C). The chitosan-coated samples have shown a greater amount of vitamin C, quercetin, rutin, and total phenolic contents than control samples. However, these nutritional parameters' levels were significantly different (p ≤ 0.05) in samples stored at room than samples stored at refrigerated temperature. However, the levels of crude fiber, potassium, and sodium were found statistically nonsignificant (p ≥0.05) in control versus chitosan treated coating treatments. The findings have documented that the coatings of 1.5 and 2.0% were most effective for extension in shelf life and maintaining the nutritional attributes of guava fruit.

Emerging pollutants (EPs) encompass natural or synthetic substances in the environment that pose potential risks but have only recently been recognized or monitored. EPs consist of various categories including pesticides, pharmaceuticals, hormones, mycotoxins, and endocrine disrupting chemicals (EDCs). Through several pathways, EPs can access food, potentially leading to health impacts when their safe concentrations are exceeded. Milk, being a highly nutritious and a heavily consumed food product by many consumers of different ages, is a crucial food matrix where EPs should be regularly monitored. In literature, large number of studies was dedicated for the determination of different EPs in dairy milk, employing different analytical techniques. Chromatographic based techniques were the most prevalent means for analysis of EPs in milk, which demonstrated significant efficiency, sensitivity and accuracy for this specific purpose. Prior to chromatographic analysis, extraction of EPs from a complex matrix like milk, is essential. This review comprehensively covers relevant research papers on extraction and subsequent detection and determination of EPs in milk by chromatographic methods from 2018 and until 2023.

Irrigation water management components evaluation is mandatory for sustainable irrigated agriculture production in the era of water scarcity. In this research spatio-temporal distribution of irrigation water components were evaluated at canal command area in Indus Basin Irrigation System (IBIS) using remote sensing based geo-informatics approach. Satellite derived MODIS product-based Surface Energy Balance Algorithm for Land (SEBAL) was used for the estimation of the Actual Evapotranspiration (ETa). Satellite derived SEBAL based ETa was calibrated and validated using the ground data-based advection aridity method (AA). Statistical analysis of the SEBAL based ETa and AA shows the mean 87.1 mm and 47.9 mm and, 100 mm and 77 mm, Standard deviation of 27.7 mm and 15.9 mm and, 34.9 mm and 16.1 mm, R of 0.93 and 0.94, NSE of 0.72 and 0.85, PBIASE -12.9 and -4.4, RMSE 34.9 and 5.76 for the Kharif and Rabi season, respectively. Rainfall data was acquired from the Tropical Rainfall Measuring Mission (TRMM). TRMM based rainfall was calibrated with the point observatory data of the Pakistan Metrological Department Stations. Canal water data was collected from the Punjab Irrigation department for the assessment of canal water availability. Water The water balance approach was applied in the unsaturated zone for the quantification of the gross and net Groundwater irrigation. Mmonthly variation of ETa with the minimum average value of 63.3 mm in January and the maximum average value of 110.6 mm in August was found. While, the average annual of four cropping years (2011-12 to 2014-15) ETa was found 899 mm. Average of the sum of Net Canal Water Use (NCWU) and Rainfall during the study period of four years was only 548 mm (36% of ETa) and this resulted the 739.6 mm of groundwater extraction. While the annual based variation in groundwater extraction of 632 mm and 780 mm was found. Seasonal analysis revealed 39% and 61% of groundwater extraction proportion during Rabi and Kharif season, respectively. The variation in four cropping year’s monthly groundwater extraction was found 28.7 mm to 120.3 mm. This variation was high in the 2011-12 to 2012-13 cropping year (0 mm to 148.7 mm), dependent upon the occurrence of rainfall and crop phenology. Net groundwater irrigation, estimated after incorporating the efficiencies was 503 mm year-1 on average for the four cropping years.

A total of 779 samples of edible nuts (melon seeds, watermelon seeds, pumpkin seeds, and cantaloupe seeds) from southern cities of Punjab, Pakistan were collected from the summer and the winter seasons. The natural occurrence of aflatoxins (AFs) and vitamin E (tocopherols) levels were investigated using HPLC. The results have shown that 180 (43.4%) samples from the winter season and 122 (33.4%) samples from the summer season were found positive with AFs. The elevated average levels of total AFs (20.9±3.10 µg/kg) were observed in watermelon seeds without shell and the lowest average amount (15.9±3.60 µg/kg) were documented in melon seeds without shell samples from the winter season. The elevated average amount of total AFs 17.3±1.50 µg/kg were found in pumpkin seeds available as without shell. The results have documented a significant difference in total AFs levels in edible seeds available as shells versus without shells (α = 0.05 & 0.01). The highest dietary intake of 6.30 µg/kg/day was found in female individuals from pumpkin seeds (without shell) in the winter season and the value of 3.00 µg/kg/day were found in pumpkin seed without shell in summer season in female individuals. The highest amount of total tocopherol levels of 22.2 ± 7.70 ng/100g in pumpkin seeds samples from winter season and 14.5 ± 5.50 mg/100g were found in melon seeds samples from summer season. The variation of total tocopherol levels in edible seeds among the winter and summer seasons showed significant difference (p ≤ 0.0054), except watermelon seeds samples which shown non-significant difference (p ≥ 0.183).

Deep Neural Network (DNN) inference demands substantial computing power, resulting in significant energy consumption. A large number of negative output activations in convolution layers are rendered zero due to the invocation of the ReLU activation function. This results in a substantial number of unnecessary computations that consume significant amounts of energy. This paper presents ECHO: Energy-efficient Computation Harnessing Onilne Arithmetic - A MSDF-based accelerator for DNN inference, designed for computation pruning, utilizing an unconventional arithmetic paradigm known as online/ most-significant digit first (MSDF) arithmetic which performs computations in a digit-serial manner. The MSDF digital serial computation of online arithmetic enables overlapped computation of successive operations leading to substantial performance improvements. The online arithmetic, coupled with a negative output detection scheme, facilitates early and precise recognition of negative outputs. This, in turn, allows for the timely termination of unnecessary computations, resulting in a reduction of energy consumption. The implemented design has been realized on the Xilinx Virtex-7 VU3P FPGA and subjected to a comprehensive evaluation through a rigorous comparative analysis involving widely used performance metrics. Experimental results demonstrate promising power and throughput improvements compared to contemporary methods. In particular, the proposed design achieved an average improvement in power consumption of up to 81%, 82.9%, and 40.6% for VGG-16, ResNet-18, and ResNet-50 workloads compared to the conventional bit-serial design, respectively. Furthermore, significant average speedups of 2.39×, 2.6×, and 2.42 were observed when comparing the proposed design to conventional bit-serial designs for VGG-16, ResNet-18, and ResNet-50 models respectively.

The molecular mechanisms underlying heat stress tolerance in animals to high temperatures remain unclear. This experiment was performed with Sprague-Dawley rats housed at 22 ℃ (control group; CT), and 42 ℃ for 30 min (H30), 60 min (H60), and 120 min (H120). Transcriptomic analysis using RNA-Sequencing (RNA-Seq) from blood (CT and H120), liver (CT, H30, H60, and H120), and adrenal glands (CT, H30, H60, and H120) was performed. The differentially expressed mRNA isoforms (DEIs) were identified and annotated by the CLC Genomics Workbench. Biological process and metabolic pathway analyses were performed using Gene Ontology (GO) and Kyoto Encyclopedia of Genes and Genomes (KEGG) database. A total of 225, 5,764, and 4,988 DEIs in the blood, liver, and adrenal glands were observed. Furthermore, the number of novel differentially expressed transcript lengths with annotated genes and the novel differentially expressed transcript with non-annotated genes were 136 and 8 in blood, 3,549 and 120 in the liver, as well as 3,078 and 220 in adrenal glands, respectively. A total of 35 genes were involved in the heat stress response, out of which Dnaja1, LOC680121, Chordc1, AABR07011951.1, Hsp90aa1, Hspa1b, Cdkn1a, Hmox1, Bag3 and Dnaja4 were commonly identified in the liver and adrenal glands, suggesting that these genes may regulate heat stress response through interactions between liver and adrenal glands. The results suggest that the identified mRNA isoforms could be considered as potential candidates for selecting mammals to improve thermotolerance.

Glaciers in northern Pakistan are a prime source of freshwater, providing headwater in the Indus river system and serving as a lifeline to millions of people in the region. These glaciers undergo continuous changes by melting due to global warming or accumulation due to snowfall/precipitation at higher altitudes. In this study, we used remote sensing data to quantify glacier changes in spatiotemporal variability in the past three decades. Five glaciers in the Gilgit region (near the junction of the Hindukush and Karakoram Mountains) with an extent of less than 5 square kilometers were selected, namely Phakor glacier, Karamber glacier, East Gammu glacier, Bhort glacier, and Bad-e-Swat glacier. The fluctuations in these glaciers were monitored using a digital elevation model (DEM) and a cloud-free continuous series of Landsat satellite pictures from the minimal snow cover season. The annual climatic trends were studied through spatially interpolated gridded climate data WοrldClim version-1 climate database for 1970 – 2000. We used it to study the variations of minimum and maximum temperature, solar radiation, and precipitation through the preparation of sub-sets from the original global grids. Because of its exact delineation in the Gilgit sub-basin, the characterized watersheds were visually compared to optical Landsat 8 OLI data for mountainous ridge matching, revealing that SRTM 30m (radar-based) demonstrated greater accuracy than other DEMs. The temporal assessment of Bhort, Bad-e-Sawat, East Gammu, Karamber, and other rivers was also carried out. It is observed that the glaciers in the Gilgit watershed are rather stable. The little variability of glaciers is due to their geographic condition, altitude, topography, and orientation. Validation of the mapped glacier classes has been performed to check the accuracy assessment through an error matrix method. The kappa coefficient from the error matrix has been calculated to be 84 %. The study makes a critical input to a greater understanding of watershed controlling and hydrological processes in the upper Indus catchment's Gilgit watershed.

The transition from undergraduate dental student to the actual practicing dentist is a crucial phase and ensuring the preparedness of graduates for the complexity and demands of contempo-rary dental practice is a challenging task. This study aimed to evaluate the self-perceived prepar-edness of undergraduate dental students and house officers in the dental colleges of Pakistan. Cross-sectional national study was planned to collect the information from dental students and new graduates in Pakistan. The pre-validated Dental Undergraduates Preparedness Assessment Scale (DU-PAS) was used. Purposive sampling technique was utilized to recruit house officers and undergraduate dental students from 27 dental schools in Pakistan. The data analysis was car-ried out using the R statistical environment for Windows (R Core Team, 2015). The total of 862 responses with 642 females and 219 males were analyzed in the study. Overall, clinical skills score was 30.56+9.08 and score for soft skills was 30.54+10.6. The mean age of the participants was 23.42+1.28. Deficiencies were reported in various soft skills and clinical skills attributes.The results highlighted the strengths and weaknesses of dental students and new graduates in Pakistani den-tal institutions. The findings may be used to further develop and strengthen teaching and training of dental students in Pakistan.

Scientific studies on the impact of wood species on solid fuel production, performance, and sustainability are grossly inadequate. The knowledge of this is imperative as users of solid fuels are increasing rapidly, especially in Africa. On this note, it becomes necessary to explore measures that will improve its efficiency and sustainability as an energy source. This study investigates some properties of selected wood species used as an energy source in Nigeria and their pelleting potential. Nine (9) samples were characterized and assessed for suitability of pelleting following four wood pellet quality standards. The findings revealed Anogeissus leiocarpus as the species with the best rating score in terms of fuel properties while Vitellaria paradoxa as the lowest. However, in terms of conformity with the four wood pellets standards, Khaya senegalensis, Parkia biglobosa and Anogeissus leiocarpus having presented density, calorific value, sulfur, arsenic, cadmium, and lead within the limits of the wood pellet quality standards were considered the best wood species in terms of fuel suitability and pelleting potential. The findings therefore suggest that not all wood species are suitable as fuel. Thus, for species that do not meet the standard wood pellet requirements, alternatives such as the use of biomass blends, additives, or process adjustments can be employed to adapt the quality to the standards or by using the fuels in improved cookstoves.

A total of 744 samples of vegetable seeds and oil (soybean, sunflower, canola, olive, corn, and mustard) were collected for the presence of aflatoxin B1 (AFB1) and total aflatoxins (AFs). The results have shown that 92 (56.7%) samples of branded and 108 (57%) samples of non-branded edible seeds were observed to be contaminated with AFs. The maximum mean of AFB1 and total AFs in non-branded soybean seeds was 21.01 ± 4.70 and 36.37 ± 6.10 µg/kg, respectively. Furthermore, all samples of edible seeds have concentrations of AFB1 greater than the proposed limit of European Union (EU, 2 µg/kg) and 12 (7.40%) samples of branded seeds and 14 (7.40%) samples of non-branded seeds were found in the range ≥ 50 µg/kg. About 78 (43.3%) samples of branded edible oil and 103 (48.3%) sample of non-branded edible oil were observed to be positive with AFs, and the elevated average of AFB1 (14.29 ± 2.51 µg/kg) and total AFs (25.61 ± 7.50) µg/kg were found in non-branded soybean oil samples. Furthermore, 16 (8.88%) and 6 (3.33%) samples of branded vegetable oil have levels of total AFs in a range (21 - 50 µg/kg) and ≥ 50 µg/kg, respectively. The findings have indicated significant difference of AFs levels between branded and non-branded vegetable oil samples (t = 22.274 and p = 0.000) at α = 0.05 and significant difference of AFs levels in vegetable seeds and oil samples ( t = -17.75, p = 0.000) at α =0.05. The highest dietary intake was found in non-branded sunflower oil sample (0.90 µg/kg/day) in female individuals (16-22 age group), followed by the dietary intake of 0.69 µg/kg/day body weight in male individuals (16-22 age group).

Aluminum (Al) and manganese (Mn) toxicity are the top two constraints to crop production in acid soil. Crops have evolved common and specific mechanisms to tolerate the two stresses. In the present study, the responses (toxicity and tolerance) of wheat near-isogenic lines (ET8 and ES8) and their parents (Carazinho and Egret) to Al and Mn were compared by determining physiolog-ical parameters and transcriptome profiling of roots. The results showed that: (1) Carazinho and ET8 exhibited dual tolerance to Al and Mn as compared with Egret and ES8, indicated by higher relative root elongation and SPAD; (2) After entering into roots, Al was mainly distributed in the root and fixed in the cell wall, while Mn was mainly distributed in the cell sap and then trans-ported to leaves. Both Al and Mn stresses decreased the contents of Ca, Mg, and Zn; Mn stress al-so inhibited the accumulation of Fe, while Al showed an opposite effect; (3) Transcriptomic analy-sis identified 5581 differentially expressed genes (DEGs) under Al stress and 4165 DEGs under Mn stress. Among these, 2774 DEGs were regulated by both Al and Mn stresses, while 2280 and 1957 DEGs were exclusively regulated by Al and Mn stress, respectively. GO and KEGG analyses indi-cated that cell wall metabolism responds exclusively to Al, while nicotianamine synthesis exclu-sively responds to Mn. Pathways such as signaling, phenylpropanoid metabolism, and metal ion transport showed commonality and specificity to Al and Mn. TFs, such as MYB, WRKY, and AP2 families, were also regulated by Al and Mn, and WGCNA identified PODP7, VATB2, and ABCC3 as the hub genes for Al tolerance and NAS for Mn tolerance. The identified genes and pathways can be used as targets for pyramiding genes and breeding multi-tolerant varieties.

Human displacement is on the rise globally, and the increase in the burden of tuberculosis (TB) is also attributed to migrations worldwide. A significant number of such displacement occur in regions with considerably higher areas of TB burden. Displacements may delay in TB diagnosis and treatment, which possibly will lead to TB transmission among healthy individuals. In this study, we assessed the association of existing determinants after a protracted internal displacement of people with the delay in TB diagnosis and treatment outcomes. A cross-sectional study was conducted on internally displaced TB patients registered at selected health facilities in three urban districts of Pakistan from March 2019 to February 2020. The univariate and multivariate logistic regression model was used to assess the delay in diagnosis and treatment outcomes. IDPs with delay in initiation of treatment beyond 30 days were at high possibility of unsuccessful TB treatment outcomes (adjusted odds ratio AOR,2.60; 95% CI 1.06-6.40). Analysis of factors that affect health seeker behavior and timely treatment showed a significant association (p<0.05) in-between age group 55-65 years (AOR, 2.66; 95% CI 1.00-7.07), female patients (AOR, 2.42; 95% CI 1.21-4.81), visited non-formal health provider (AOR, 8.81; 95% CI 3.99-19.46), self-medication (AOR, 2.72; 95 % CI 1.37-5.37), poor knowledge of TB (AOR, 11.39; 95% CI 3.31-39.1), and perceived stigma (AOR, 8.81; 95% CI 3.99-19.4). Prolong delay in treatment was associated with unfavorable treatment outcomes among IDPs, more specifically. As migrants and IDPs are more likely to experience an interruption in care due to overall exclusion from social and health care services. Therefore, it is imperative to understand the barriers in providing public health care services, particularly in preventing and treating TB.

The outbreak of 2019-novel coronavirus (SARS-CoV-2) that causes severe respiratory infection (COVID-19) has spread in China, and the world health organization declared it pandemic. However, no approved drug or vaccines are available, and treatment is mainly supportive and through a few repurposed drugs. In this urgency situation, development of SARS-CoV-2 based vaccines is immediately required. Immunoinformatic and molecular modelling are generally used time-efficient methods to accelerate the discovery and design of the candidate peptides for vaccine development. In recent years, the use of multiepitope vaccines is proved to be a promising immunization strategy against viruses and pathogens, which induce more comprehensive protective immunity. The current study demonstrated a comprehensive in-silico strategy to design stable multiepitope vaccine construct (MVC) from B-cell and T-cell epitopes of essential SARS-CoV-2 proteins with the help of adjuvants and linkers. The integrated molecular dynamics simulations analysis revealed the stability of MVC and its interaction with human Toll-like receptors (TLRs), which trigger an innate and adaptive immune response. Later, the in-silico cloning in a known pET28a vector system also estimated the possibility of MVC expression in E. Coli. Despite this study lacks validation of this vaccine construct in terms of its efficacy, the current integrated strategy encompasses the initial multiple epitope vaccine design concepts. After validation, this MVC can present to be a better prophylactic solution against COVID-19.

This paper presents a symmetrical topology for the design of solid-state transformer, made up of power switching converters, to replace conventional bulky transformers. The proposed circuitry not only reduces the overall size but also provides power flow control with the ability to be interfaced with renewable energy resources (RESs) to fulfill the future grid requirements at consumer end. Solid state transformer provides bidirectional power flow with variable voltage and frequency operation and has the ability to maintain unity power factor, and current total harmonic distortion (THD) for any type of load within defined limits of IEEE standard. Solid State Transformer offers much smaller size as compared to that of the conventional iron core transformer. MATLAB/Simulink platform is adopted to test the validity of the proposed circuit for different scenarios by providing the simulation results evaluated at 25 kHz switching frequency.

In this work, we report the engineering of a sub-70 nm nanocomposite of ZnO/Zn2TiO4 using a low-temperature solution-phase method. Titanium isopropoxide and zinc acetate were used as precursors, and isopropyl alcohol and water were used as solvents. The investigation focused on the growth of nanocomposites by varying the concentrations of precursors and surfactants, as well as their efficiency within different pH ranges. All three ZnO/Zn2TiO4 nanocomposites consist of hexagonal wurtzite ZnO and Zn2TiO4 structures in the three nanocomposites. The crystallite size in three ZnO/Zn2TiO4 nanocomposites, with a hexagonal wurtzite ZnO structure, were measured to be 62.67, 40.34, and 39.50 nm. The crystallite size values in three ZnO/Zn2TiO4 nanocomposites were 26.15 nm, 25.36 nm, and 21.24 nm, respectively, with Zn2TiO4. Morphological observations, conducted using FESEM, reveal the formation of three ZnO/Zn2TiO4 nanocomposites across the entire sample. These nanocomposites resemble dispersed cotton packets, with sizes ranging from 18 to 350 nm. Peaks in the range of 610-1250cm-1 are attributed to Ti-O bond formation and peak located at 1350-1450 cm-1 are attributed to Zn-O bond formation. Also, EDX spectrum reveals peaks for various sample components such as Ti, O and Zn. UV spectrums confirmed the formation of three nanocomposite of ZnO/Zn2TiO4 as showing two peaks for each sample. Photocatalytic investigation carried out by analyzing the UV-Visible absorption spectra of methylene blue dye on the surface of ZnO/Zn2TiO4 nanocomposites, dye degradation at various irradiation time intervals, dye degradation at varied catalyst concentrations and the influence of pH on dye-degradation. Furthermore, the said nanocomposites were used to degrade environmental pollutant (Methylene blue dye). Different sets of experiments were conducted under ambient conditions which show an excellent photo catalytic degradation efficiency.

Antibiotic resistance (ABR) is an emerging global threat to public health. Substantial evidence has indicated that community pharmacists (CPs) can play a critical role in managing the ever-increasing threat of antibiotic resistance. The study aimed to determine the knowledge, attitude, and practices of CPs (n=180) towards antibiotics and antibiotic resistance as well as to improve the rational use of antibiotics. Two phases of mixed methods (quantitative and qualitative) online study were conducted in Pakistan from August 2019 to March 2020 by using validated questionnaires and semi-structured interview data. Different statistical methods were used to tabulate the quantitative data whereas inductive thematic analysis was conducted to categorize themes from the qualitative data and draw conclusions. Approximately 64.4% were male (mean: 29-33 years old). Overall, CPs had good knowledge of and were familiar with superbugs and their roles in ABR (65.6%, Median=1, IQR=1) although they were poor in differentiating some antibiotic groups with their respective ABR patterns (31.1%, Median=1, IQR=1). Most CPs have a positive attitude towards antibiotics with most (90.0%) having identified ABR as a critical issue in public health (Median=1, IQR=0). Overall, CPs' practices towards antibiotics were reasonable where they tend to educate patients about the rational use of antibiotics (52.8%, Median=1, IQR=1). Two main themes (antibiotics and counseling of patients) were related to self-medication with while educational interventions are the sub-theme. ABR is multifactorial where the subthemes related to budget, time constraints incompetent staff, the absence of CPs, the lack of training, enforcement of laws and regulations are the need of the hour in Pakistan. Effective antibiotic stewardship programs, patient education, and awareness campaigns about antibiotics and ABR along with training of the CPs are important factors that have to be addressed in a timely manner.

This paper analyses the design and implementation of REDD+ in the West African region, an important global biodiversity area. Drawing on in-depth interviews, analysis of policy documents and observation of everyday activities, we sought to understand how REDD+ has been designed and implemented in Nigeria and Ghana. We draw on tools from political ecology to examine how, and why REDD+ takes the form it does in these countries. We focus on three key dimensions that emerged as strong areas of common emphasis in our case studies -- capacity building, carbon visibility, and property rights. First, we show that, while REDD+ design generally foregrounds an ostensible inclusionary politics, its implementation is driven through various forms of exclusion. This contradictory inclusion-exclusion politics, which is partly emblematic of the neoliberal provenance of the REDD+ policy, is also a contingent reality and a strategy for navigating complexities and pursuing certain interests. Second, we show that though the emergent foci of REDD+ implementation in our case studies align with global REDD+ expectations, they yet manifest as historically and geographically contingent processes that reflect negotiated and contested relations among actors that constitute the specific national circumstance of each country. We conclude by reflecting on the wider implications of these findings for understanding REDD+ implementation more broadly.

Conventional plant breeding methods exploit already existing genomic variation in plants to develop a variety in 8 to 10 years, which can decrease the genetic variability of the plant’s genome. The ever-increasing food demand for cereals crops cannot be met by traditional breeding methods. In order to increase food production in less time, there is a dire need to improve breeding methods. Several conventional and molecular breeding methods are being used to improve the crops traits. Molecular researchers have developed new genome editing tools like CRISPR/Cas9, CRISPR/Cpf1, prime editing, base editing, dcas9 epigenetic modification, and several other transgene-free genomes editing approaches. These genome editing tools can improve the desired traits precisely and efficiently. Moreover, a newly developed breeding method “Speed Breeding” has revolutionized the agriculture by shortening the crop cycle. It can produce 5-6 generations of cereals in a year. In this review, we have summarized all these conventional and molecular breeding approaches to improve cereal crops.

A 1-year prospective study was carried out on patients in the ICU unit at a tertiary care hospital, Hail, Kingdom of Saudi Arabia. A total of 163 bacterial isolates were obtained from different clinical specimens with a high proportion of bacteria found associated with ventilator-associated pneumoniae (70, 43%), followed by catheter-associated urinary tract infection (39, 24%), central line-associated bloodstream infection (25, 15%), and surgical site infection (14, 8.6%). Klebsiella pneumoniae was the most common isolate (39, 24%), followed by Acinetobacter baumannii (35, 21.47%), Pseudomonas aeruginosa (25, 15%), and Proteus spp (23, 14%). Among the highly prevalent bacterial isolates, extended-spectrum beta-lactamase was predominant (42, 42.4%). Proper use of antibiotics, continuous monitoring of drug sensitivity patterns, and taking all precautionary measures to prevent beta-lactamases-producing organisms in the clinical settings are crucial and significant factors to fend off life-threatening infections and for a better outcome.

Due to the increase in the emission of greenhouse gases, the hydrologic cycle is being altered on the daily basis. This has affected the variations in relations of intensity, duration, and frequency of rainfall events. Intensity Duration Frequency (IDF) curves describe the relationship between rainfall intensity, rainfall duration and return period. IDF curves are one of the most often applied implements in water resource engineering, in areas such as for operating, planning and designing of water resource projects, or for numerous engineering projects aimed at controlling floods. In particular, IDF curves for precipitation answer problems of improper drainage systems or conditions and extreme characters of precipitation which are the main cause of floods in Nyabugogo catchment. This study aims to establish Rainfall IDF empirical equations, curves and hydrological discharge (predicted peak rate of runoff (Qlogy)) equations for eight Districts that will be used for designing an appropriate and sustainable hydraulic structures for controlling flood to reduce potential loss of human and aquatic life, degradation of water, air and soil quality and property damage and economic lessen caused by flood in Nyabugogo catchment. However Goodness of Fit tests revealed that Gumbel’s Extreme-Value Distribution method appears to have the most appropriate fit compared with Pearson type III distribution for validating the Intensity-Duration-Frequency curves and equations through the use of daily annual for each meteorological station. The findings of the study show that the intensity of rainfall increases with a decrease in rainfall duration. Additionally, a rainfall of every known duration will have a higher intensity if its return period is high, while the predicted peak rate of runoff (Qlogy) increases also with an increase in the intensity of rainfall.

The healthcare domain is increasingly adopting IoT and Electronic Health Record (EHR) systems, generating vast volumes of healthcare data. This shift is driven by the growing need of delivering the right information to the right individuals, at the right time. The latter underscores the importance of adopting a comprehensive strategy for efficiently collecting, utilizing, and analyzing health-related data to not only enhance overall healthcare management but also for the provision of timely and personalized prevention strategies. The latter is of highest importance especially in scenarios where lack of effective treatments or poor survival rates (such in pancreatic cancer) renders typical healthcare strategies ineffective. In this article, we introduce an innovative and integrated platform that is specifically designed and developed for accessing, processing, and analyzing data in challenging healthcare scenarios, such as dealing with pancreatic cancer. This platform, called iHelp, combines multidisciplinary technologies and provides healthcare professionals reliable risk modelling, analysis, and prediction techniques so that individuals (at risk of developing pancreatic cancer) can be provided with timely, reliable, and personalized prevention and intervention measures. A key innovation in the iHelp platform is the standardized data management approach called Holistic Health Records (HHRs) that facilitate the capturing of all health determinants in a standardized and well-structured way for processing towards the provision of health risk detection and personalized healthcare decision support. In the development of iHelp platform, the HHRs are evaluated through different real-world healthcare datasets, including datasets coming from hospital systems, data from wearables, questionnaires, and mobile applications.

Pain is a multifaceted multisystem disorder that adversely affects neuro-psychological processes. This study compares the effectiveness of central-stimulation (tDCS) and peripheral-stimulation (TENS) in pain-inhibition during a cognitive-task in healthy volunteers and to observe potential neuro-cognitive improvements. Healthy eighty volunteers went through a complete experimental protocol comprising pain-induction (CPT), administration of tDCS/TENS, EEG-data acquisition, and cognitive assessments. The protocol for this study is categorized into 04-groups: G1(Control), G2(TENS), G3(Anodal-tDCS), and G4(Cathodal-tDCS). Paired t-tests (p

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

Contamination in coastal regions attributed to fluoride and nitrate cannot be disregarded, given the substantial environmental and public health issues they present worldwide. Maintaining water quality is crucial for environmental well-being. This comprehensive study was performed to assess the spatial as well as indexical water quality, identify contamination sources, and evaluate associated health risks pertaining to nitrate and flouride in AlHassa region, KSA. The physiochemical results revealed a pervasive pollution of the overall groundwater. The dominant water type was Na-Cl, indicating saltwater intrusion and reverse ion exchange impact. Spatiotemporal variations in physicochemical properties suggest diverse hydrochemical mechanisms, with geogenic factors primarily influencing groundwater chemistry. The groundwater pollution index varied between 0.8426 and 4.7172, classifying samples as moderately to very highly polluted. Similarly, the synthetic pollution index (in the range of 0.5021-4.0715) revealed that none of the samples had excellent water quality, with various degrees of pollution categories. Nitrate Health Quotient (HQ) values indicated chronic human health risks ranging from low to severe, with newborns being the most vulnerable. Household use of nitrate-rich groundwater for showering and cleaning did not pose significant health risks. Fluoride HQ decreased with age, and children faced the highest risk of fluorosis. The Hazard Index (HI) yielded moderate to high-risk values. Nitrate risks were 1.21 times higher than fluoride risks, as per average HI assessment. All samples fell into the vulnerable category based on the Total Hazard Index (THI), with 88.89% classified as very high risk. This research provides valuable insights into groundwater quality, guiding water authorities, inhabitants, and researchers in identifying safe water sources and vulnerable human populations. The results highlight the need for appropriate treatment techniques and long-term coastal groundwater management plans.