The current deformation and stable state of slopes with historical shatter signs is a concern for engineering construction. Suspected landslide scarps were discovered at the rear edge of the slope of the Genie in the Sichuan-Tibet transportation corridor during a field investigation. In order to qualitatively determine the current status of the surface deformation of this slope, this paper uses high-resolution optical remote sensing, airborne LiDAR and InSAR technologies for comprehensive analysis. The interpretation of high-resolution optical and airborne LiDAR data revealed that the rear edge of the slope exhibits three levels of scarps. However, no deformation was detected with the D-InSAR analysis of ALOS-1 radar images from 2007 to 2008 or with the Stacking-InSAR and SBAS-InSAR processing of Sentinel-1A radar images from 2017 to 2020. A geological model of the slope was established in combination with field investigation stipulating that the slope is composed of steep anti-dip layered dolomite limestone and that the scarps at the rear edge of the slope were caused by historical shallow toppling. Further research is recommended to determine the extent of toppling deformation and evaluate the slope stability under the disturbance of tunnel excavation.

Atmospheric propagational phase variations are the dominant source of error for InSAR timeseries analysis, generally exceeding uncertainties from poor SNR or signal correlation. The spatial properties of these errors have been well studied, but their temporal dependence and correction have received much less attention to date. We present here an evaluation of the magnitude of tropospheric artifacts in derived time series after compensation using an algorithm that requires only the InSAR data themselves. The level of artifact reduction equals or exceeds that from many weather model based methods, while avoiding the need to access fine-scale atmosphere parameters globally at all times. Our method consists of identifying all points in an InSAR stack with consistently high correlation, and computing, then removing, a fit of the phase at each of these points with respect to elevation. Comparison with GPS truth yields a reduction of 3, from an rms misfit of 5-6 cm to ~2 cm over time. This algorithm can be readily incorporated into InSAR processing flows without need for outside information.

The holy town of Joshimath, gateway to the India-China border and religious places like Badrinath, Hemkunt Sahab, Valley of flowers in the Uttarakhand state of India experienced cracks in many of the residential and commercial buildings in the month of November-December 2022 which created panic and relocation of people. The reason(s) for the subsidence is still not known but using the InSAR technology and data from Sentinel-1, SAR data for the region was processed using HyP3 and MintPy for January-December 2022 to understand when the phenomenon started and how much uplift/subsidence the area has underwent in the last one year, as no such study is available till today. The entire town can be classified into two zones with respect to the annual subsidence values. Severe subsidence has been observed in the North and East regions whereas most of the southern region experienced moderate to low subsidence. Since the town is built on the debris of an old landslide, the subsidence may be attributed to the change in the course of the underground water channels due to heavy and continuous construction happening in the region and also due to drop in the water table. The results shows that the subsidence in the region was ongoing since June (from January till May, almost negligible vertical movement was recorded) which accelerated after September (when an uplift was recorded which lasted till October), while the subsidence peaked in the month of December with recorded subsidence of as much as 10 cm in some areas located around the Joshimath town, where most of the residential and commercial buildings are located.

Generalized stacking fault energies of palladium alloys were calculated using the density functional theory. The stacking fault energy of palladium alloys is correlated with the valence electron of the transition metal element. The twinning tendency is also modified by the presence of an alloying element in the plane of deformation. The obtained results suggest that Pd –transition metal alloys with elements such as Cr, Mo, W, Mn, Re are expected to exhibit high work hardening rate due to the tendency to emit of the partial dislocations and mechanical twins, which results in increased strength and ductility.

InSAR and associated analytic methods can measure surface deformation from low earth orbit with a claimed accuracy of centimeters to millimeters. The realized accuracy depends on the area being measured and on the choice of analytic method, suggesting one choose a method in response to the area being measured. Here we consider a specific fixed analytic method and compare the results it produces to measurements gathered from other means in a variety of settings. In particular we compare Sentinel-1 InSAR with GPS at the Kilauea volcano around the 2018 eruption, with GPS in the city of Arica, Chile, and with public survey data at a decommissioned tailings mine. In addition, we compare two independent Sentinel-1 InSAR analyses for a railway station in Oslo, Norway. Our goal is estimate the accuracy of a fully automated Sentinel-1 InSAR pipeline in various settings. Our conclusions are that centimeter level accuracy is a reasonable claim in many, but not all settings, and that accuracy is typically not lost by using an automated pipeline, instead of hand-selecting and tuning parameters.

We describe an efficient and cost effective data access mechanism for Sentinel-1 TOPS 1 mode bursts. Our data access mechanism enables burst-based data access and processing, thereby 2 eliminating ESA’s Sentinel-1 SLC data packaging conventions as a bottleneck to large scale processing. 3 Pipeline throughput is now determined by available compute resources and efficiency of the analysis 4 algorithms. For targeted infrastructure monitoring studies, we are able to generate coregistered, 5 geocoded stacks of SLCs for any AOI in the world in a few minutes. In addition, we describe our 6 global scale radar backscatter and interferometric products and associated pipeline design decisions 7 that ensure geolocation consistency across the suite of derived products from Sentinel-1 data. Finally, 8 we discuss the benefits and limitations of working with geocoded SAR SLC data.

The InSAR technique measures the displacement of an indicator using SAR image interference. The technique of interfering two SAR images among InSAR techniques is called Differential InSAR (D-InSAR). In the process of D-InSAR, the filtering technique is used in the Unwrapped Mask, usually using the GoldStein method. However, since the Goldstein method removes the noise on the path, it is difficult to derive the displacement value in the agricultural area where the relative coherence is low. In Korea, more than 50% of the whole country consists of mountainous regions and agricultural regions, so it is difficult to use the Goldstein technique polysynthetically. In this study, we set the test-bed for the urban area and the agricultural area based on Coherence, and introduce Goldstein and Boxcar Filter, one of the Goldstein and LSM techniques. Through this process, we want to draw the conclusion which is displacement values ​​in the agricultural area.

Traditional applications of Interferometric Synthetic Aperture Radar (InSAR) data involved inverting an interferogram stack to determine the average displacement velocity. While this approach has useful applications in continuously deforming regions, much information is lost by simply fitting a line through the time series. Thanks to regular acquisitions across most of the the world by the ESA Sentinel-1 satellite constellation, we are now in a position to explore opportunities for near-real time deformation monitoring. In this paper we present a simple statistical approach for detecting offsets and gradient changes in InSAR time series. Our key assumption is that 5 years of Sentinel-1 data is sufficient to calculate the population standard deviation of the detection variables. Our offset detector identifies statistically significant peaks in the first, second and third difference series. The gradient change detector identifies statistically significant movements in the second derivative series. We exploit the high spatial resolution of Sentinel-1 data and the spatial continuity of geophysical deformation signals to filter out false positive detections that arise due to signal noise. When combined with near-real time processing of InSAR data these detectors, particularly the gradient change, could be used to detect incipient ground deformation associated with geophysical phenomena, for example from landslides or volcanic eruptions.

This study presents an analysis of subsidence rates and their effects on Mexico City. Mexico City is well known for its subsidence as a result of excess water withdrawal for many years. This study focuses on this problem utilizing the integration of Interferometric Synthetic Aperture Radar (InSAR), Continuous Global Positioning Systems (CGPS), and optical remote sensing data. Fifty-two ENVISAT-ASAR, nine GPS stations, and one Landsat ETM+ image from Mexico City area have been analyzed to prepare a better understanding of the subsidence rates and its effects on Mexico City’s commune. This study has utilized InSAR methods. It includes differential interferometry and Persistent Scatter Interferometry (PSI) to monitor the existing subsidence in the Mexico City area. The InSAR data covers the temporal baseline between 2002 until June 2010, and the GPS data include temporal baseline from 1998 until 2012. Maximum of 352 mm annually change in Line Of Sight (LOS) direction is in agreement with the previous geodetic studies. InSAR data have been compared with CGPS data at the same time interval. The finding of this study reveals a high amount of correlation (up to 0.98) between two independent geodetic methods. We also implemented the Support Vector Machine (SVM) analysis method based on Landsat ETM+ image to classify Mexico City’s populated density area. This method performed comparing the subsidence rates with populated area buildings. This integrated study shows that the fastest subsidence zone (i.e., areas greater than 100 mm/yr) in the over mentioned temporal baseline occurs in the high and sparsely populated areas

Laser powder bed fusion can fabricate porous structure through lattices, but it remains a challenge to prepare micropores (

Falls, especially those left unattended, are fatal for the elderly. Several efforts have been made to use the Internet of Things and Machine Learning algorithms to detect falls. All such systems have issues such as (a) sensor placement on the torso and thigh which will be uncomfortable for the elderly. (b) Predictions made on the cloud- the result of the prediction is then sent back to the end device to raise an alert. This is prone to network connectivity and latency issues. We have built an end/device that is wrist-worn and has multiple Inertial Measurement Unit sensors and a heart sensor. We have developed three novel ensemble algorithms (a)Stack(A) (b) Variable weighted Ensemble Voting algorithm-B(VWE(B)), and (c) Variable weighted Ensemble Voting algorithm-C (VWE(C)). Since the ensemble algorithm is run on the end-device built around Qualcomm Snapdragons 820c, we do both feature extraction and selection to reduce data dimensionality. We have used multiple methods such as (a) Identifying features that have maximum impact (b) Principal Component Analysis (PCA) (c) Shapley’s values (d) Cross-Correlation combined with relliefF. We got an accuracy of 97% and specificity of 99%. In this paper, we present the analysis of the system with and without pruning.

Cigar stacking fermentation is a key step in tobacco aroma enhancement and miscellaneous gas reduction, which both have a great influence on increasing cigar flavor and improving industrial availability. To analyze the effect of cigar tobacco leaf (CTLs) microbial community structure on volatiles during cigar stacking fermentation, this study used multi-omics technology to reveal the changes in microbial community structure and volatiles of different cigar varieties during stacking fermentation, in addition to exploring the interaction mechanism of microbiome and volatiles. The results showed that the dominant microbial compositions of different CTL varieties during stacking fermentation were similar, which included Staphylococcus, Corynebacterium 1, Aerococcus, and Aspergillus. These dominant microbes mainly affected the microbial community structure and characteristic microorganisms of CTLs through microbial interactions, thereby influencing the transformation of volatiles. Characteristic microorganisms of different CTLs varieties such as Trichothecium, Trichosporon, Thioalkalicoccus and Jeotgalicoccus, were found to posively correlate with characteristic volatiles like megastigmatrienone 4, pyrazine, tetramethyl-, geranyl acetone, and 2-undecanone, 6,10-dimethyl-, respectively. This in turn affected the aroma and sensory quality of the CTLs. This study provides theoretical support for the analysis of the mechanism of microorganisms on volatiles and aroma, and development of microbial agents during cigar stacking fermentation.

Recently, ice with the stacking disorder structure, consisting of random sequences of cubic ice (Ic) and hexagonal ice (Ih) layers, is reported to be more stable than pure Ih/Ic. While, due to a much lower free energy barrier of heterogeneous nucleation, in practice, the freezing process of water is usually controlled by heterogeneous nucleation which is triggered by an external medium. Herein, molecular dynamic simulations were carried out to explore the polymorph dependence of ice on the lattice structure of substrates. It turns out that, during the nucleation stage, the polymorph of ice nuclei can be severely altered by the graphene substrate, on which the Ih was found to occupy an absolute majority in new-formed ice. This can be attributed to the structure similarity between graphene and basal face of Ih. Besides the nucleation stage, our results suggest that the substrate can not affect the polymorph of ice which is far from the graphene surface. The polymorph selectivity of graphene to Ih will diminish with the growth of ice layer.

In this paper, we study the usage of machine learning models for sales time series forecasting. The effect of machine learning generalization has been considered. A stacking approach for building regression ensemble of single models has been studied. The results show that using stacking technics, we can improve the performance of predictive models for sales time series forecasting.

Influenced by geological, climatic, and natural weathering factors, the Great Wall heritage is sus-ceptible to deformations, posing significant challenges to the comprehensive preservation of the Great Wall sites. To investigate techniques for monitoring deformations in extensive linear cultural heritage sites, such as the Great Wall, this study utilizes the SBAS-InSAR technique for deformation monitoring and analysis. A dataset comprising 161 Sentinel-1A images spanning from March 2017 to January 2022 was chosen for SBAS-InSAR processing, yielding a deformation velocity field. To verify result credibility, a typical mountainous segment spanning approximately 896.53 km within the Great Wall landscape corridor underwent analysis. The findings suggest that around 75.8% of the landscape corridor along the Shanxi section of the Ming Great Wall maintain relative stability, displaying deformation rates varying from -10 to 10 mm/year. The remaining 24.2% of the land-scape corridor experiences notable deformations, including a maximum subsidence rate of 33.1 mm/year and a maximum subsidence of 148.6 mm. This study illustrates the potential utility of the SBAS-InSAR technique for monitoring and evaluating surface deformations in extensive linear cultural heritage sites.

In permafrost regions, ground surface deformations induced by freezing and thawing threaten the integrity of the built environment. Mapping the frost susceptibility of the ground at a high spatial resolution is of practical importance for the construction and planning sectors. We processed Sentinel-1 Interferometric Synthetic Aperture Radar (InSAR) data from thawing seasons 2015 to 2019, acquired over the area of Ilulissat, West Greenland. We used a least-squares inversion scheme to retrieve the average seasonal displacement (S) and long-term deformation rate (R). We secondly investigated two different methods to extrapolate active layer thickness (ALT) measurements, based on their statistical relationship with remotely-sensed surface characteristics. A Generalized Linear Model (GLM) was first implemented, but the model was not able to fit the data and represent the ALT spatial variability over the entire study domain. ALT were alternatively averaged per vegetation class, using a land cover map derived by supervised classification of Sentinel-2 images. We finally estimated the active layer ice content and used it as a proxy to map the frost susceptibility of the ground at the community scale. Fine-grained sedimentary basins in Ilulissat were typically frost susceptible and subject to average seasonal downward displacements of 3 to 8 cm. Areas following a subsiding trend of up to 2.6 cm/yr were likely affected by permafrost degradation and melting of ground ice below the permafrost table. Our approach enabled us to identify frost-susceptible areas subject to severe seasonal deformations, and/or long-term subsidence induced by degrading permafrost. Used in combination with traditional site investigations, InSAR maps provide valuable information for risk management and community planning in the Arctic.

The Apennine sector formed by Sannio and Irpinia is one of the most important seismic districts in Italy, representing a good case of study due to the plenty of recorded earthquakes that have therein occurred from Roman times up to nowadays. We have merged the historical record and the new satellite techniques that allow a precise determination of ground movements, and then derived physical dimensions like strain rate. In this way, we have verified that in Irpinia the hazard of new strong shocks forty years after one of the strongest known seismic events in the district is still high. This aspect must be considered very important from many points of view, particularly for Civil Protection plans, as well as civil engineering and urban planning development.

Two new coordination compounds of Mn(II) and Cu(II) viz. [Mn(bz)2(Hdmpz)2(H2O)] (1) and [Cu(crot)2(Hdmpz)2] (2) (where, bz = benzoate, crot = crotonate, Hdmpz = 3, 5-dimethyl pyrazole) have been synthesized and characterized using single crystal X-ray diffraction technique, FT-IR, electronic spectroscopy, TGA and elemental analyses. Compounds 1 and 2 crystallize as mono-nuclear coordination compounds of Hdmpz based penta-coordinated Mn(II) and hexa-coordinated Cu(II) respectively containing distorted trigonal bipyramidal and distorted octahedral geome-tries. Crystal structure analysis of compound 1 reveals the presence C‒H⋯π and π-stacking in-teractions along with O‒H⋯O, N‒H⋯O and C‒H⋯O H-bonding interactions which stabilizes the layered assembly of the compound. Similarly, the presence of hydrogen bonding along with π-stacking interactions stabilizes the crystal structure of compound 2. We have carried out theo-retical investigations to analyze π⋯π H-bonding and antiparallel CH···π non-covalent interac-tions observed in the compounds. DFT calculations were performed to evaluate strength of these interactions energetically. Moreover, QTAIM and non-covalent interaction (NCI) plot index computational tool were used to characterize them and evaluate the contribution of the H-bonds.

Granular superconductivity at high temperatures in graphite can emerge at certain two-dimensional (2D) stacking faults (SFs) between regions with twisted (around the c-axis) or untwisted crystalline regions with Bernal (ABA...) and/or rhombohedral (ABCABCA...) stacking order. One way to observe experimentally such 2D superconductivity is to measure the frozen magnetic flux produced by a permanent current loop that remains after removing an external magnetic field applied normal to the SFs. Magnetic force microscopy was used to localize and characterize such a permanent current path found in one natural graphite sample out of ∼50 measured graphite samples of different origins. The position of the current path drifts with time and roughly follows a logarithmic time dependence similar to the one for flux creep in type II superconductors. We demonstrate that a ≃10nm deep scratch on the sample surface at the position of the current path causes a change in its location. A further scratch was enough to irreversibly destroy the remanent state of the sample at room temperature. Our studies clarify some of the reasons for the difficulties of finding a trapped flux in remanent state at room temperature in graphite samples with SFs.

Time series ground deformation monitoring and reservoir parameter inversion are crucial for the dynamic assessment of oilfield resources and sustainable exploitation in an oilfield. As one of the regions with the richest oil reserves in China, the oilfield areas in the western Qaidam Basin are selected as a typical study area. Firstly, we used SAR images collected by the Sentinel-1A satellite from January 2021 to December 2022 and applied the Multidimensional Small Baseline Subset (MSBAS) method to obtain vertical and east-west deformation measurements. On this basis, a nonlinear Bayesian inversion method was applied to model the shallow reservoir in a series of complex deformation areas, based on a single-source model and a multi-source model, respectively. As a result, the ground deformation monitoring results obtained by long time series InSAR clearly reflect the uneven ground deformation caused by the oil extraction and water injection operation process. There is slight subsidence in the Huatugou oilfield, while significant uplift deformation occurred in the Ganchaigou oilfield and the Youshashan oilfield, with a maximum uplift rate of 48 mm/year. Further analysis indicates that the introduction of the 2D deformation field helps to improve the robustness of oilfield reservoir parameter inversion. Moreover, the dual-source model is more suitable than the single-source model for inverting complex deformation reservoir parameters. This study not only fills the blank of InSAR deformation monitoring for the oilfields in the western Qaidam Basin but also provides a theoretical reference for model and method selection of reservoir parameter inversion in other oilfields.

We identify the source of the Mw = 5.6 earthquake that hit west-central Epirus on March 21, 2020 00:49:52 UTC. We use synthetic aperture radar interferograms tied to one permanent Global Navigation Satellite System (GNSS) station (GARD). We model the source by inverting the INSAR displacement data. The inversion model suggests a shallow source on a low-angle fault (39°) dipping towards east with a centroid depth of 8.5 km. The seismic moment deduced from our model agrees with those of the published seismic moment tensors. This geometry is compatible with the Margariti thrust fault within the collision zone between Apulia and Eurasia. We also processed new GNSS data and estimate a total convergence rate between Apulia and Eurasia of 8.9 mm yr-1 , of which shortening of the crust between the Epirus coastal GNSS stations and station PAXO in the Ionian Sea is equivalent to ~ 50% of it or 4.6 mm yr−1. A 60-km wide deformation zone takes up nearly most of the convergence between Apulia-Eurasia, trending N318°E. Its central axis runs along the southwest coast of Corfu, along the northeast coast of Paxos, heading toward the northern extremity of the Lefkada island.

Persistent land subsidence or uplift can cause serious latent hazards to urban infrastructure. To thoroughly investigate the causes and impacts of land surface deformation, this study examines the case of Wuxi City, focusing on the land fluctuation patterns in the region following the enforcement of the groundwater abstraction prohibition policy in 2005. This research utilizes the PS-InSAR technique to quantify land surface deformations in the Wuxi region from November 2015 to June 2023 and analyzes 100 SAR images to obtain comprehensive spatiotemporal evolution data of the land surface. Furthermore, this study conducts an in-depth analysis of the effects of various factors, including groundwater, precipitation, and soil geology, on the characteristics of land surface deformation. It pioneers the application of the GARCH (Generalized Autoregressive Conditional Heteroskedasticity) model to analyze the time-series displacement in the study area and innovatively introduces the "amplitude factor" index to assess land surface fluctuations. This study investigates the recent land surface deformation patterns and mechanisms in Wuxi City. By integrating the "amplitude factor", it provides a scientific foundation for future urban development and disaster mitigation strategies in Wuxi City, offering valuable insights for related research.

The rock strata movement deformation generated by the mining process of the mine will inevitably lead to surface subsidence and a series of environmental hazards, so it is particularly important to monitor the rock strata movement deformation and surface subsidence in the goaf area. With the development of surface subsidence monitoring technology, InSAR technology has been widely used in the research of surface subsidence in mining areas with the advantages of high precision and wide monitoring. In this paper, by obtaining the image data of 59 Sentinel-1A scenes in the mining area, the obtained PS points were analyzed and processed by ArcGIS difference analysis by PS-InSAR technology, and the surface deformation cloud map and settlement curve of the mining area in various periods were obtained, and the rock strata movement deformation and surface subsidence law of the goaf before treatment and after different treatment methods were studied by influencing factors such as stope layout and mining depth. The results show that the rock strata movement deformation and surface subsidence degree of the goaf under different treatment methods are different due to different influencing factors, and their positions also change dynamically with time. Applying InSAR technology to study rock strata movement deformation and surface subsidence can provide an important basis for mine safety mining, goaf treatment, rock strata movement deformation and surface subsidence monitoring.

Since the early 1990s, the European (ESA) and Italian (ASI) space agencies have managed and distributed a huge amount of satellite-recorded SAR data to the research community and private industries. Moreover, the availability of advanced cloud computing services implementing different multi-temporal SAR interferometry techniques allows the generation of deformation time series from massive SAR images. We exploit the information provided by a large PS dataset to determine the temporal trend of ground deformation and the relative deformation rate with millimetric accuracy to analyse the spatial and temporal distribution of land subsidence induced by water pumping from a deep confined aquifer in the Northern Valle Umbra Basin (Central Italy), exploiting 24 years of Permanent Scatterers – Interferometric SAR data archives. The SAR images were acquired between 1992 and 2016 by satellite ERS1/2, ENVISAT and Sentinel 1 ESA missions, and the COSMO-SkyMed ASI mission). We observe ground velocities and deformation geometries between 1992 and 2016, with displacements of more than 70 cm and velocities of up to 55 mm/yr and the results suggest that the shape and position of the surface ground displacement are controlled by the fault activity hidden under the valley deposits.

ITRF input data which are integrated by GNSS, SLR, VLBI, DORIS combination centers are considered to be relatively high-quality and accurate solutions. However, when utilizing these inputs, one still needs to identify outliers, rescale inaccurate covariance matrix and evaluate the precision of the observed datum information. To achieve the above-mentioned objectives, we propose a terrestrial reference frame (TRF) stacking approach to establish the single technical reference frameworks for the ITRF2014 and ITRF2020 datasets of all four technologies. As a result, roughly 0.5% or less of the SLR observations are identified as outliers, while the ratio of DORIS, GNSS, and VLBI observations are below 1%, around 2%, and ranging from 1% to 1.2%, respectively. The post-rescaling covariance scale factors are 25.07, 27.25, 18.84, 6.98 for GNSS, SLR, VLBI, and DORIS in ITRF2014 datasets, and 8.95, 14.9, 16.8, 7.78 in ITRF2020 datasets, respectively. It is shown that the consistency between the SLR scale and ITRF has improved, increasing from around -5mm in ITRF2014 datasets to approximately -1mm in ITRF2020 datasets. The scale velocity derived from fitting the VLBI scale parameter series with all epochs in ITRF2020 datasets differs by approximately 0.21mm/year from the velocity obtained by fitting the data up to 2013.75 because of the scale drift of VLBI at around 2013. The decreasing standard deviations of the Polar motion parameter (XPO, YPO) offsets between Stacking TRFs and 14C04 (20C04) indicating an improvement in the precision of polar motion observations for all of the four techniques. From the perspective of the Weighted Root Mean Square in station coordinates, the measurement precision of GNSS, SLR, and DORIS techniques has improved, while VLBI shows no significant change.

In the present study, piecewise integrated composite (PIC) bumper beam for passenger cars was proposed and design optimisation process for composite bumper beam against IIHS test was carried out with the help of machine learning. Several elements in IIHS bumper FE model have been assigned to be references, in order to collect training data which, allow the machine learning model to study the method of predicting loading types of each finite element. 2-D and 3-D implementations were provided by machine learning models, which determined stacking sequences of each finite element in PIC bumper beam. It was found that the PIC bumper beam, which was designed by machine learning model has direct impact on reducing the possibility of failure as well as increasing bending strength effectively than conventional composite bumper beam. Moreover, 3-D implementation produced better results compared with 2-D implementation since it was preferable to choose loading type information which was achieved from surroundings when the target elements were located either at corner or junction of planes instead of using information came from the same plane of target.

In 2018, the author identified a previously unknown/unreported association between dexrazoxane and poly(ADP-ribose) (PAR). Interestingly, PAR is a close structural analogue of the polyadenine nucleotide polymer, polyadenosine monophosphate (poly(A)). In this report, subsequent in silico modelling of the interaction between dexrazoxane and poly(A) reveals some notable differences from the previously reported interaction between dexrazoxane and PAR. Significantly, the supramolecular self-assembly of dexrazoxane and poly(A) is distinguished by vertically-orientated nonelectrostatic forces comparable to the stabilizing interactions between stacked bases within DNA. Notably, the vertical separation of 3.4 Å between each stack is consistent with solvent entropy as a dominant driving force in stabilising the interaction. Additionally, concomitant conformational analysis by the author reveals the existence of low energy planar conformers of dexrazoxane. This analysis enables an explanation for the considerable discrepancies and conflicts that exist within the reported pharmacokinetic data for dexrazoxane. Exploring the significance of the interaction between dexrazoxane and poly(A), the author illustrates that survival, translation and replication of the severe acute respiratory syndrome virus 2 (SARS-CoV-2) is absolutely dependent upon the mature and unhindered poly(A) tail of the SARS-CoV-2 genome. The proposition herein, that dexrazoxane, as a chameleonic agent sequesters the poly(A) tail of the SARS-CoV-2 genome by the catalysis of a supramolecular hybrid assembly establishes SARS-CoV-2 infected cells as deep compartments for the accumulation of dexrazoxane. Taken together, dexrazoxane or its demethylated analogue, represent a novel treatment to kill the SARS-CoV-2 virus by irreversible destabilization of the SARS-CoV-2 poly(A) tail.

Three low band gap copolymers based on isoindigo acceptor units were designed and successfully synthesized by direct arylation polycondensation method. Two of them were benzodithiophene(BDT)-isoindigo copolymers (PBDTI-OD and PBDTI-DT) with 2-octlydodecyl(OD) and 2-decyltetradecyl (DT) substituted isoindigo units, respectively. Thiophene donor and DT-substituted isoindigo acceptor units were copolymerized to synthesize PTI-DT. The copolymers have broad absorption range that extends to over 760 nm with a band gap ~ .5 eV. The photophysical property studies showed the BDT based copolymers have non-polar ground states. Their emission exhibited the population of intramolecular charge transfer (ICT) state in polar solvents and tightly bound excitonic state in non-polar solvents due to self-aggregation. On the contrary, the emission from the thiophene based copolymers was only from the tightly bound excitonic state. The thermal decomposition temperature of the copolymers was above 380 oC. The X-ray diffraction pattern of the three copolymers showed a halo due pi-pi stacking. A second sharper peak was observed in the BDT-based copolymer with longer side chain on the isoindigo unit (PBDTI-DT) and the thiophene based copolymers with PTI-DT exhibiting a better structural order.

Chemical versatility of organic semiconductors provides nearly unlimited opportunities for tuning their electronic properties. However, despite decades of research, relationship between molecular structure, molecular packing and charge mobility in these materials remains poorly understood. This reduces the search for high-mobility organic semiconductors to the inefficient trial-and-error approach. For clarifying the abovementioned relationship, investigations of the effect of small changes in the chemical structure on OSs properties are particularly important. In this study, we address computationally the impact of substitution of C-H atom pairs by nitrogen atoms (N-substitution) on molecular properties, molecular packing and charge mobility of crystalline oligoacenes. Besides of decreasing frontier molecular orbital levels, N-substitution dramatically alters molecular electrostatic potential yielding pronounced electron-rich and electron-deficient areas. These changes in the molecular electrostatic potential strengthen face-to-face and edge-to-edge interactions in the corresponding crystals and result in the crossover from the herringbone packing motif to π-stacking. When the electron-rich and electron-deficient areas are large, sharply defined and, probably, have certain symmetry, charge mobility increases up to 3-4 cm2V-1s-1. The results obtained highlight the potential of azaacenes for application in organic electronic devices and are expected to facilitate rational design of organic semiconductors for steady improvement of organic electronics.

In today's context of rising sea levels and subsiding land topography, coastal flooding is a major concern for coastal areas, both nationally, regionally, and internationally. A detailed understanding of these two phenomena is a prerequisite for effective coastal flood management. The main objective of the present study is to contribute to the understanding of the impact of subsidence and sea-level rise on coastal flooding in Saint-Louis, and in particular the Langue de Barbarie, by producing a vulnerability map of submerged surfaces. To this end, the Synthetic Aperture Radar (SAR) interferometry technique is used to process a time series of Sentinel-1 images and estimate land subsidence in the Saint-Louis and Langue de Barbarie area. Interferometric SAR (InSAR) measurements are merged with RCP 2.6 sea-level rise scenarios to identify predicted flooded areas and provide a flood vulnerability map. At the Langue de Barbarie, topographic subsidence is estimated at between -6.4 and -0.4mm/year. In this study, we show that local land subsidence may increase vulnerability to flooding caused by sea-level rise based on 2100 projections. This may represent an increase in the flood zone in the study area. Based on the RCP 2.6 scenario and the subsidence rates obtained, a significant part of the St. Louis coastline and city would be subject to coastal and fluvial flooding for the years 2040 and 2100. For these dates, 29 to and 36 Km2 of the studied area would be occupied by water. Given this situation, research in Saint-Louis needs to focus on adaptation scenarios to coastal risks, to protect coastal communities and safeguard the city's historical heritage.

The dust originating from the extinct lake of the Aral Sea poses a considerable threat to the sur-rounding communities and ecosystems. The accurate location of these wind erosion areas is an essential prerequisite for controlling sand and dust activity. However, few relevant indicators re-ported in the current study can accurately describe and measure wind erosion intensity. A novel wind erosion intensity (WEI) of a resolution unit was defined in this paper based on the deformation due to the wind erosion in this resolution unit. We also derived the relationship between WEI and soil InSAR temporal decorrelation (ITD). The ITD is usually caused by the surface change over time, which is very suitable for describing wind erosion. However, within one resolution unit, the ITD signal usually includes soil and vegetation contributions, and few studies are referred to this. Therefore, we proposed an ITD decomposition model (ITDDM) to decompose the ITD signal of a resolution unit. The least-squares method (LSM) based on singular value decomposition (SVD) is used to estimate the ITD of soil (SITD) within a resolution unit. We verified the results qualitatively by the landscape photos, which can reflect the actual conditions of the soil. At last, the WEI of the Aral Sea from June 23, 2020, to July 05, 2020, was mapped. The results confirmed that (1) Based on the ITDDM model, the SITD can be accurately estimated by the LSM method, (2) the Aral Sea is experiencing severe wind erosion, and (3) The middle, northeast, and southeast bare areas of the South Aral Sea are where salt dust storms may occur.

The dual-station Interferometric Synthetic Aperture Radar (InSAR) system can overcome the physical limitations imposed by the baseline of single-station dual-antenna InSAR. It provides greater flexibility and can enhance elevation measurement accuracy through a well-designed baseline configuration.Unmanned aerial vehicles (UAV) equipped with dual-station InSAR, with relatively low cost and high flexibility, are useful for mapping and land resource exploration. However, due to challenges including spatiotemporal synchronization and motion errors, there are limited reports on UAV-borne dual-station InSAR. This paper proposes a comprehensive method for processing data from small UAV-borne dual-station InSAR by integrating two-way synchronization chain signals. The proposed method includes compensation for time and phase synchronization errors, trajectory refinement with synchronized chain and Position and Orientation System (POS) data, high-precision dual-station InSAR imaging and interferometric processing. Height inversion results based on the proposed method is also provided, demonstrating the effectiveness of the proposed method and improving interferometric accuracy at calibration points from 0.66 meters to 0.42 meters.

In order to alleviate the conflict between populations and land-resource, Tianjin has adopted multi-phase reclamation projects to formed large-scale artificial reclamation land. However, the reclamation areas are susceptible to subsidence, which demonstrate a serious threat to infrastructure and people’s lives and property. The SBAS-InSAR was used to acquired surface deformation of Tianjin Binhai New Area from January 2017 year to December 2022 year, analyzed in depth the response relationship between land subsidence and reclamation projects time as well as the land use type. The results show that the Lingang Industrial Zone was the earliest to be reclaimed, with extensive reclamation completed by 2016 year, while Nangang Industrial Zone and Hangu Port started reclamation projects in 2009 year, some areas are still currently under construction. There is a strong correlation between surface deformation and reclamation time, the severe land subsidence occurred over newly reclaimed areas. Surface deformation gradually intensifies from west to east, the maximum surface settlement in Nangang Industrial Zone, Lingang Industrial Zone from the west to the east has changed from -50 mm to -890 mm,45 mm to -580 mm, respectively, reclamation area of Hangu Port with maximum surface deformation is -250 mm. Significant differences deformation among different land use types, which reclamation projects completed in the same time. Subsidence is positively correlated with surface load, in areas with higher surface loads, the surface settlement is also severer,the average surface settlement for the heavy shipyard, 67 grain storage tanks, 27 grain storage tanks, road, and bare land are -201 mm, -166 mm, -107 mm, -64 mm, and -43 mm, respectively. This study reveals significant differences of surface deformation in the reclamation completed at different times and the load is the main driving factor of settlement difference in the reclamation land completed at the same time. Which has important guiding significance for preventing and controlling geological disasters in the reclamation area and later development planning.

Landslide is one of the most common geological disasters in China, which is characterized by suddenness and uncertainty, and it is difficult to realize accurate identification, early warning and forecasting of landslide disaster by conventional means. With the development of high-resolution remote sensing satellites and InSAR surface deformation monitoring technology, the traditional means of landslide monitoring data sources are limited, and there is a lack of effective methods to excavate the characteristics of the spatial distribution of landslide hazards and their triggering factors and other issues. In this paper, the area extending 10 km outside the VII isobar of the Gengma earthquake is taken as the study area, and 13 evaluation factors are screened out by integrating the factors of InSAR surface deformation, topography and geological environment, and the Bayesian Optimized Convolutional Neural Network (BO-CNN) is used for the evaluation of landslide susceptibility, and the BO-RF and PSO-SVM models are selected for the comparative analysis. The model accuracy evaluation was carried out by three indexes: ROC curve, AUC value and FR value, in which the ROC curves of PSO-SVM, BO-RF and BO-CNN were all close to the upper-left corner of the corner, and the AUC values were 0.9388, 0.9529, and 0.9535, respectively, and the FR value of landslide in the high susceptibility area of BO-CNN was as high as 14.9, and was higher than that of PSO-SVM and BO-RF, respectively. SVM and BO-RF model is 4.55 and 3.69 higher, the experimental results show that the BO-CNN model used in this paper has a better effect in landslide susceptibility evaluation, and the research results of the local government's disaster prevention and mitigation measures are of great significance.

InSAR and associated analytic methods enable relative surface deformation measurements from low Earth orbit with a potential accuracy of centimeters to millimeters. However, assessing the actual accuracy can be quite difficult. The analytic methods are complicated enough that naive analytic error propagation is infeasible, and, in many settings, InSAR practitioners lack sufficient ground truth to assess results. Phase noise due to partial decorrelation from changes in the scattering properties of the ground is a prominent source of accuracy loss. In this paper we present a method to assess the loss of precision due to this component of phase noise. The proposed method consists of generating synthetic data stacks whose statistical properties match those of the actual input SAR data stacks, and then using the synthetic data for an ensemble calculation. The spread of the results of the ensemble calculation indicates the loss of precision. We show examples of the ensemble analysis at a mining operation in South Africa, and demonstrate the ability to estimate the precision of two InSAR deformation retrieval methods on a point-by-point and epoch-by-epoch basis.

Since the 1970s, land subsidence has been developing rapidly in the Beijing Plain, the systematic study of its evolution mechanism is of great significance to the sustainable development of the regional economy. First, based on ENVISAT ASAT and RADARSAT2 data, the land subsidence data in Beijing Plain were obtained using permanent interferometer technology. Second, based on the GIS platform and using fishing net tools, vector data of ground settlement with different resolutions were obtained. Through a series of tests, a scale of 960 metres was selected as the research unit, and the subsidence rate of the grid was obtained from 2004 to 2015. Finally, based on the Mann-Kendall mutation test method, a trend analysis of land subsidence changes in various grids was carried out. The results showed that single-year mutation mainly distributed in the middle and lower parts of the Yongding River alluvial fan and the Chaobai River alluvial fan, mainly occurring in 2015, 2005 and 2013, respectively. The upper and middle alluvial fan of the Chaobai River, the vicinity of the emergency water source and the edge velocity of the groundwater funnel have undergone several sudden changes. Combined with hydrogeology, basic geological conditions and the impact of the South-to-North Water transfer project, we analysed the causes of the mutations in the grid. The research results can provide a basis for the study and prevention of land subsidence in this area and help to further explore the trend characteristics of land subsidence in this area.

Accurately distinguishing between indolent and aggressive tumors is a crucial unmet need in the clinical management of prostate cancer (PCa). The traditional Gleason grading system has been utilized for this purpose; however, there is often ambiguity in classifying tumors with a Gleason grade of 7. Clinicians commonly resort to using secondary Gleason grades, such as 3+4 or 4+3, to classify these tumors as indolent or aggressive, respectively. Unfortunately, such classifications are prone to misinterpretation, leading to erroneous diagnoses and prognoses. To address this challenge, we investigated the application of Machine Learning (ML) techniques to classify PCa patients based on gene expression data sourced from The Cancer Genome Atlas. By comparing gene expression levels between indolent and aggressive tumors, we sought to identify distinctive features for developing and validating a range of ML algorithms and stacking techniques. The stacking based model achieved an impressive accuracy of 96% for all samples encompassing primary Gleason grades 6 to 10. Notably, when excluding Gleason grade 7 from the analysis, the accuracy further improved to 97%. This study underscores the effectiveness of the stacked ML algorithm for accurately classifying indolent versus aggressive PCa. Leveraging gene expression data and employing a combination of classifiers, this approach offers a powerful solution to address the unmet need in robustly distinguishing between different types of PCa tumors. Future implementation of this methodology may significantly impact clinical decision-making and patient outcomes in the management of prostate cancer.

Protein phosphorylation and ADP-ribosylation (ADPr), as two types of post-translational modifications (PTM), are the process of adding phosphate group and ADP-ribose moieties to proteins, respectively. Although both PTM types can occur on many amino acid types, serine is the most common. Serine phosphorylation (pS), serine ADPr (SADPr), and their in situ crosstalks (pSADPr) play essential roles in biological processes. Although in silico classifiers have been developed for predicting pS and SADPr sites, the classifier for predicting pSADPr sites is unavailable. In this study, we developed classifiers to predict pSADPr sites. Specifically, we collected 3250 human pSADPr, 7520 SADPr, 151,227 pS and 80,096 unmodified serine sites. Based on them, we investigated the characteristics of pSADPr sites and constructed three classifiers to predict pSADPr sites from the pS dataset, the SADPr dataset and the protein sequences separately. We built and evaluated five deep-learning classifiers in ten-fold cross-validation and independent test datasets. Three of them (e.g. Convolutional Neural Network with the One-Hot encoding, dubbed CNNOH) performed better than the rest two. For instance, CNNOH had the AUC values of 0.700, 0.914 and 0.954 for recognizing pSADPr sites from the SADPr, pS and unmodified serine sites.Therefore, it is challenging to distinguish pSADPr sites from SADPr sites compared to the other two. It is consistent with our observation that pSADPr's characteristics are more similar to those of SADPr than the rest. Furthermore, we used the classifiers as base classifiers to develop a few stacking-based ensemble classifiers to improve performance. However, none of the ensemble classifiers showed better performances, suggesting that the base classifiers have good enough performances. Finally, we developed an online tool for extensively predicting human pSADPr sites based on the CNNOH classifier, dubbed EdeepSADPr. It is freely available through http://edeepsadpr.bioinfogo.org/.

Link prediction is an iconic problem in complex networks because deals with the ability to predict nonobserved existing or future parts of the network structure. The impact of this prediction on real applications can be disruptive: from prediction of covert links between terrorists in their social networks to repositioning of drugs in molecular diseasome networks. Here we compare: (1) an ensemble meta-learning method (Ghasemian et al.), which uses an artificial intelligence (AI) stacking strategy to create a single meta-model from hundreds of other models; (2) a structural predictability method (SPM, Lü et al.), which relies on a theory derived from quantum mechanics and does not assume any model; (3) a modelling rule named Cannistraci-Hebb (CH, Muscoloni et al.), which relies on one brain-bioinspired model adapting to the intrinsic network structure.We conclude that brute-force stacking of algorithms by AI does not perform better than (and is often significantly outperformed by) SPM and one simple brain-bioinspired rule such as CH. This agrees with the Gödel incompleteness: stacking is optimal but incomplete, you cannot squeeze out more than what is already in your features. Hence, we should also pursue AI that resembles human-like physical ‘understanding’ of simple generalized rules associated to complexity. The future might be populated by AI that ‘steals for us the fire from Gods’, towards machine intelligence that creates new rules rather than stacking the ones already known.

The coseismic surface three-dimensional deformation fields were significant for quantified the geometric and kinematic characteristics of earthquake rupture faults. Traditional geodetic techniques were constrained by their intrinsic limitations, such as InSAR, which could only extract far-field deformation fields due to its incoherence, and GNSS, which could only acquire deformations at discrete points. The recently developing optical pixel correlation technique based on high resolution remote sensing images could acquire the near-field coseismic horizontal deformation. In this study, the vertical displacement field of the 2022 Mw 6.6 Menyuan earthquake was obtained by differencing the pre- and post-earthquake DEMs from GaoFen-7 stereo satellite images. Further, the line-of-sight (LOS) and azimuthal (AZI) directions far-field deformations by InSAR, the horizontal near-field deformation by optical pixel correlation based on pre- and post-earthquake GF-2/7 images, and the vertical deformation by differencing the pre- and post-earthquake DEMs, were incorporated to comprehensively solve the complete three-dimensional deformation fields of the 2022 Mw 6.6 Menyuan earthquake. Firstly, the vertical displacement field by differencing DEMs indicated there were significant vertical displacements about 1 m at the bend region, which was induced by the local compressive stress. In addition, at the epicenter on the middle segment of ruptured Lenglongling fault (LLLF), the maximum lifting occurred on the southern sides of the main and secondary faults exceeded 2 m. Secondly, the three-dimensional deformation fields solved by multiple deformation data demonstrated that the near-field deformation field calculated by optical pixel correlation method could quantify the displacements distributed over the rupture fault zone, which were not available on the InSAR deformation maps. Finally, the surface 2D strain derived from the displacement maps calculated by optical pixel correlation revealed high strain concentration on the rupture fault zone. Our study focused on the complete surface three-dimensional deformation estimation from multiple far- and near-field deformation data, and provided a new perspective for a deeper understanding of the characteristics of coseismic surface deformation and the rupture pattern of the fault.

The current study aims to apply and compare the performance of six machine learning algorithms, including three basic classifiers: random forest (RF), gradient boosting decision tree (GBDT), and extreme gradient boosting (XGB), as well as their hybrid classifiers, using the logistic regression (LR) method (RF+LR, GBDT+LR, and XGB+LR), in order to map the landslide susceptibility of Zhangjiajie City, Hunan Province, China. First, a landslide inventory map was created with 206 historical landslide points and 412 non-landslide points, which was randomly divided into two datasets for model training (80%) and model testing (20%). Second, 15 landslide conditioning factors (i.e., altitude, slope, aspect, plane curvature, profile curvature, relief, roughness, rainfall, topographic wetness index (TWI), normalized difference vegetative index (NDVI), distance to roads, distance to rivers, land use/land cover (LULC), soil texture, and lithology) were initially selected to establish a landslide factor database. Thereafter, the multicollinearity test and information gain ratio (IGR) technique were applied to rank the importance of the factors. Subsequently, we used a series of metrics (e.g., accuracy, precision, recall, f-measure, area under the ROC (receiver operating characteristic) curve (AUC), kappa index, mean absolute error (MAE), and root mean square error (RMSE)) to evaluate the accuracy and performance of the six models. Based on the AUC values derived from the models, the GBDT+LR model with the highest AUC value (0.8168) was identified as the most efficient model for mapping landslide susceptibility, followed by the XGB+LR, XGB, RF+LR, GBDT, and RF models, which achieved AUC values of 0.8124, 0.8118, 0.8060, 0.7927, and 0.7883, respectively. The results from this study suggest that the stacking ensemble machine learning method is promising for use in landslide susceptibility mapping in the Zhangjiajie area and is capable of targeting the areas prone to landslides.

Interferometry Synthetic Aperture Radar (InSAR) is an advanced remote sensing technique for studying the earth's surface topography and deformations. It is used to generate high-quality Digital Elevation Models (DEMs). DEMs are a crucial and primary input to various topographical quantification and modelling applications. The quality of input DEMs can be further improved using fusion methods, which combine multi-sensor or multi-temporal datasets intelligently to retrieve the best information amongst the input data. This research study is based on developing a Neural Network based fusion approach for improving InSAR based DEMs in plain and hilly terrains. The study areas comprise of relatively plain terrain from Ghaziabad and hilly terrain of Dehradun and their surrounding regions. The training dataset consists of DEM elevations and derived topographic attributes like slope, aspect, topographic position index (TPI), terrain ruggedness index (TRI), and vector roughness measure (VRM) in different land use land cover classes of the study areas. The spaceborne altimetry ICESat-2 ATL08 photon data is used as a reference elevation. A Feed Forward Neural Network with backpropagation algorithm is trained based on the prepared training samples. The trained model produces fused DEMs by learning the relationship between the input and target samples. This is used to predict elevations in the test areas. The accuracy of results from the models are assessed with TanDEM-X 90 m DEM. The fused DEMs show significant improvement in terms of RMSE over the input DEMs with improvement factor of 94.65 % in plain area and 82.62 % in hilly area. The study concludes that the ANN with its universal approximation property is able to significantly improve the fused DEM.

For Interferometry Synthetic Aperture Radar (InSAR), the normal baseline is one of the main factors that affect the accuracy of the ground elevation. For Gaofen-3 (GF-3) InSAR processing, the poor accuracy of the real-time orbit determination resulting in a large baseline error, leads to the modulation error in azimuth and the slope error in range for timely Digital Elevation Model (DEM) generation. In order to address this problem, a baseline estimation method based on external DEM is proposed in this paper. Firstly, according to the characteristic of the real-time orbit of GF-3 images, orbit fitting is executed to remove the non-linear error factor. Secondly, the height errors are obtained in slant-range plane between Shuttle Radar Topography Mission (SRTM) DEM and the GF-3 generated DEM after orbit fitting. At the same time, the height errors are used to estimate the baseline error which has a linear variation. In this way, the orbit error can be calibrated by the estimated baseline error. Finally, DEM generation is performed by using the modified baseline and orbit. This procedure is implemented iteratively to achieve a higher accuracy DEM. Based on the results of GF-3 interferometric SAR data for Hebei, the effectiveness of the proposed algorithm is verified and the accuracy of GF-3 real-time DEM products can be improved extensively.

Soil temperature is a fundamental parameter in water resources and engineering. A cost-effective model which can forecast soil temperature accurately is extensively needed. Recently, many studies have applied artificial intelligence (AI) at both surface and underground levels for soil temperature prediction. However, there is no comprehensive and detailed assessment of the performance of different AI approaches in soil temperature estimation, and primarily limited atmospheric variables are used as input data for AI models. In the present study, great varieties of various land and atmospheric variables are applied to evaluate the performance of a wide range of AI methods on soil temperature prediction. Herein, thirteen approaches, from classic regressions to well-established methods of random forest and gradient boosting to advanced AI techniques like multi-layer perceptron and deep learning are taken into account. The results show that AI is a promising approach in climate parameter forecast and deep learning demonstrates the best performance among other models. It has the highest R-squared ranging from 0.957 to 0.980, the lowest NRMSE ranging from 2.237% to 3.287% and the lowest MAE, ranging from 0.510 to 0.743 in predicting soil temperature. The prediction is repeated for different sizes of data, and prediction outcomes confirm the conclusion mentioned above.

The land subsidence occurring in goafs after coal mining is a protracted process. The accurate prediction of long-term land subsidence in goafs relies heavily on the availability of long-term monitoring data. However, the scarcity of continuous long-term land subsidence monitoring data subsequent to the cessation of mining significantly hinders the accurate prediction of long-term land subsidence in goafs. To address this challenge, this study proposes an innovative method based on Interferometric Synthetic Aperture Radar (InSAR) for predicting long-term land subsidence of goafs following coal mining. The proposed method employs a concatenation approach that integrates multiple short-term monitoring data from different coal faces, each with distinct cessation times, into a cohesive and uniform long-term sequence by normalizing the subsidence rates. The method was verified using actual monitoring data from the Yangquan No.2 mine in Shanxi Province, China. Initially, coal faces with same shapes but varying cessation times were selected for analysis. Using InSAR monitoring data collected between June and December of 2016, the average subsidence rate corresponding to the duration after coal mining cessation of each coal face was back-calculated. Subsequently, a function relating subsidence rate to the duration after coal mining cessation was fitted to the data. Finally, the relationship between cumulative subsidence and the duration after coal mining cessation was derived by integrating the function. The results indicated that the relationship between subsidence rate and duration after coal mining cessation followed an exponential function for a given coal face, whereas the relationship between cumulative subsidence and duration after coal mining cessation conformed to the Knothe time function. Notably, after the cessation of coal mining, significant land subsidence persisted in the goaf of the Yangquan No.2 mine for a duration ranging from 5 to 10 years. The cumulative subsidence curve along the long axis of the coal face ultimately exhibited an inclined W-shape. The proposed method enables the quantitative prediction of residual land subsidence in goafs, even in cases where continuous long-term monitoring data are insufficient, thus providing valuable guidance for construction decisions above the goaf.

Current satellite remote sensing methods struggle to detect and map forest degradation, a critical issue as it is likely a major and growing source of carbon emissions and biodiveristy loss. TanDEM-X InSAR phase height (hϕ) is a promising variable for measuring forest disturbances, as it is closely related to mean canopy height, and thus should decrease if canopy trees are removed. However, previous research has focused on relatively flat terrain, despite the fact that much of the worlds’ remaining tropical forests are found in hilly areas, and this inevitably introduces artifacts in sideways imaging systems. In this paper, we find a relationship between hϕ and aboveground biomass change in four selectively logged plots in a hilly region of central Gabon. We show that minimising the level of multilooking in the interferometric processing chain strengthens this relationship, and that degradation estimates across steep slopes in the surrounding region are improved by selecting data from the most appropriate pass directions on a pixel-by-pixel basis. This shows that TanDEM-X InSAR can measure the magnitude of degradation, and that topographic effects can be mitigated if data from multiple SAR viewing geometries are available.

Ho Chi Minh City (HCMC), the most crowded city and economic hub of Viet Nam, has been experiencing land subsidence over the past decades. This effort aims to contribute the spatial distribution of subsidence in HCMC in its horizontal and vertical components using synthetic aperture radar interferometry (InSAR) time series. To this purpose, an advanced Persistent Scatterers and Distributed Scatterers (PSDS) InSAR technique was applied to two European Space Agency (ESA) Sentinel-1 datasets consisting of 96 ascending and 202 descending images, acquired from 2014 to 2020 over the HCMC area. A time series of 33 COSMO-SkyMed ascending images was also used for comparison. The combination of ascending and descending satellite passes is used to decompose the light of sight velocities into horizontal east-west and vertical components. Taking into account the presence of east-west horizontal motion, our findings indicate that the accuracy of the decomposed vertical velocity can be improved by up to 3 mm/year for Sentinel-1 data. The obtained results revealed that subsidence is most pronounced in the areas along the Sai Gon River, in the northwest-southeast axis, and in the southwest of the city, with a maximum value of 80 mm/yr, which is in accordance with the findings of the literature. The amplitude of east-west horizontal velocities is relatively small and large-scale eastward movement can be observed in the west of the city at a rate of 3-5 mm/yr. This confirmed that the displacement in Ho Chi Minh City area is mainly vertical downward. Together, these results reinforced the remarkable suitability of ESA's SAR Sentinel-1 for subsidence applications, even for non-European countries such as Vietnam and Southeast Asia.

Nowadays, according to spectacular improvement in health care and biomedical level, a tremendous amount of data is recorded by hospitals. In addition, the most effective approach to reduce disease mortality is to diagnose it as soon as possible. As a result, data mining by applying machine learning in the field of diseases provides good opportunities to examine the hidden patterns of this collection. An exact forecast of the mortality after heart surgery will cause Successful medical treatment and fewer costs. This research wants to recommend a new stacking predictive model after utilizing the random forest feature importance method to foresee the mortality after heart surgery on a highly unbalanced dataset by using the most practical features. To solve the unbalanced data problem, a combination of the SVM-SMOTE over-sampling algorithm and the Edited-Nearest-Neighbor under-sampling algorithm is used. This research compares the introduced model with some other machine learning classifiers to ensure efficiency through shuffle hold-out and 10-fold cross-validation strategies. In order to validate the performance of the implemented machine learning methods in this research, both shuffle hold-out, and 10-fold cross-validation results indicated that our model had the highest efficiency compared to the other models. Furthermore, the Friedman statistical test is applied to survey the differences between models. The result demonstrates that the introduced stacking model reached the most accurate predicting performance after Logistic Regression.

Slope failures pose a substantial threat to mining activity due to their destructive potential and high probability of occurrence on steep slopes close to limit equilibrium conditions, often found both in open pits and in waste and tailing disposal facilities. The development of slope monitoring and modeling programs usually entails the exploitation of in situ and remote sensing data together with the application of numerical modeling, and it plays an important role in the definition of prevention and mitigation measures aimed at minimizing the impact of slope failures in mining areas. Here we present a new methodology combining satellite radar interferometry and 2D finite element modeling for slope stability analysis at a regional scale, applied within slope unit polygons. We studied a former mining area in southeast Spain, and the method proved useful in detecting and characterizing a considerably large number of unstable slopes. Out of 1,959 slope units used for the spatial analysis of the radar interferometry data, 43 were unstable, with varying values of safety factor and landslide size. Out of the 43 active slope units, 21 exhibited line of sight velocities greater than the maximum error obtained through the validation analysis (2.5 cm/year). Eventually, this work discusses the possibility of using the results of the proposed approach to devise a proxy for landslide hazard. The proposed methodology can help to provide non-expert final users with intelligible, clear and easily comparable information to analyze slope instabilities in different settings, not limited to mining areas.

This paper gives an overview of the large-scale tectonic styles encountered in orogens worldwide. Thin-skinned and thick-skinned tectonics represent two end member styles recognized in mountain ranges. Both styles are encountered in former passive margins of continental plates. Thick-skinned style including the entire crust and possibly the lithospheric mantle are associated with intracontinental contraction. Delamination of subducting continental crust and horizontal protrusion of upper plate crust into the opening gap occurs in the terminal stage of continent-continent collision. Continental crust thinned prior to contraction is likely to develop relatively thin thrust sheets of crystalline basement. A true thin-skinned type requires a detachment layer of sufficient thickness. Thickness of the décollement layer as well as the mechanical contrast between décollement layer and detached cover control the style of folding and thrusting within the detached cover units. In subduction-related orogens, thin- and thick-skinned deformation may occur several hundreds of kilometers from the plate contact zone. Basin inversion resulting from horizontal contraction may lead to the formation of basement uplifts by the combined reactivation of pre-existing normal faults and initiation of new reverse faults. In most orogens thick-skinned and thin-skinned structures both occur and evolve with a pattern where nappe stacking propagates outward and downward