Due to its economic benefits and the ability to reduce carbon emissions on a large scale, the CCUS-EOR project has been widely promoted and implemented globally. By using carbon dioxide flooding, oil water transition zone reservoirs that were once considered worthless may have new potential for development because of its rich geological reserves and high quality carbon sequestration conditions. Unlike water flooded layer, the oil in the TZ is unsaturated rather than residual oil after water flooding, which would lead to special oil-water seepage law of initial oil saturation. It is necessary to clarify special oil-water seepage law of oil-water transition zone to evaluate its production & storage potential. In this paper, we present a series of experiments to characterize the relationship between residual oil saturation and initial oil saturation. Cores in four different permeability and oil in four different viscosity are used to simulate different reservoir conditions, and that CO2 immiscible flooding experiments for each cores permeability and oil viscosity are performed with four different initial oil saturation. A total of 36 sets of CO2 flooding experiment data are used to draw the initial oil saturation & residual oil saturation chart. The results show that the residual oil saturation depends on the initial oil saturation rather than constant under certain conditions of core and oil. Under the condition of low permeability and high oil viscosity, the influence of initial oil saturation on residual oil saturation is relatively strong. The initial oil saturation & residual oil saturation chart can accurately calculate the residual oil saturation, initial water cut and final recovery based on the core permeability, oil viscosity and the initial oil saturation which is the first time to put forward this kind of chart and of the great significance to evaluate the recovery potential of the TZ.

The new regulation was introduced to the franchise market of South Korea in that an applicant who wants to be a franchiser must set up direct retail stores and run them for at least one year before recruiting franchisees. Considering the purpose of the regulation, it is inferred that once franchisers run their own stores, their franchisees would be better off than otherwise. This paper addresses one reason that the Korea Fair Trade Commission has no choice but to introduce the regulation. Along the line, this paper investigates whether franchisees would have the more likelihood to make profit in the case of that franchisers operate their own stores. The result demonstrates that this case could be true since the operation of franchiser owned stores could be helpful in reducing cost of franchisees.

Despite the recommendation to treat depression using the transcranial direct current stimulation (tDCS), novel findings raised doubts over the tDCS efficacy in managing depressive episodes. Neurophysiologic approaches to understand the specificities of brain responses to tDCS in de-pressed patients remains a feature. Objective: to compare the immediate hemodynamic responses to tDCS on left dorsolateral pre-frontal cortex (DLPFC; F3-Fp2 montage) in patients with depres-sive disorder and healthy controls (no additional stimuli). Methods: Sixteen participants were al-located in depression group and 16 in the control group. Both groups received 2mA tDCS for 20 minutes, using the F3-Fp2 montage. The hemodynamic effect over the DLPFC was assessed using near-infrared intracranial spectroscopy (NIRS) positioned on the left supraorbital region (Fp1). Mean, minimal and maximal values of baseline and post-stimulation rates of oxygen saturation (SatO2) were recorded. The oxygenated hemoglobin rates (HbO) were extracted. Results: Be-tween-group differences were detected for mean and minimal baseline rates of SatO2 and HbO levels. The depression group showed lower results compared to the control group. After the pro-tocol, only the depression group showed increased mean and minimal rates of SatO2 and HbO. The post-tDCS rates were equal for both groups. Conclusion: The findings showed immediate anodal tDCS effects over DLPFC hemodynamics. The effects were exclusive for the lowest base-line rates group, not affecting the normal oxygen rates group. The minimal increase of SatO2 and HbO rates after the protocol in the depression group suggests that those with reduced cerebral perfusion may be more affected by tDCS.

The wide-ranging effects of healthful vs. damaging consequences of UV irradiation on key physiologic parameters are reviewed in this paper. The effects are largely dependent on the wavelengths encountered, the absolute intensity and duration of the exposure, the tissues exposed, and whether the UV effects were delivered via in vivo or as an extracorporeal exposure in vitro typically performed with freshly obtained heparinized aliquots of whole blood. While damaging effects of high UV intensity may include irreversible irradiation damage to key cellular and molecular components, controlled low dosages of UV irradiation delivered via a conventional biophotonic apparatus at specific, controlled wavelengths can deliver beneficial effects on blood oxygenation, tissue repair, immune responses, glycemia, and glycated hemoglobin (HbA1c) concentrations. HbA1c is an important diagnostic marker for the effectiveness of diabetes management. Studies reviewed demonstrate increases in blood oxygenation and corresponding decreases in HbA1c concentrations following nominal biophotonic treatment and indicate that the application of this therapy extends beyond its more commonly applied applications in the treatment and control of infectious illnesses.

Fluorescence microscopic images of cells contain a large number of morphological features that are used as an unbiased source of quantitative information about cell status, through which researchers can extract quantitative information about cells and study the biological phenomena of cells through statistical and analytical analysis. As an important research object of phenotypic analysis, images have a great influence on the research results. Saturation artifacts present in the image result in a loss of grayscale information that does not reveal the true value of fluorescence intensity. From the perspective of data post-processing, we propose a two-stage cell image recovery model based on generative adversarial network to solve the problem of phenotypic feature loss caused by saturation artifacts. The model is capable of restoring large areas of missing phenotypic features. In the experiment, we adopt the strategy of progressive restore to improve the robustness of the training effect, and add the contextual attention structure to enhance the stability of the restore effect. We hope to use deep learning methods to mitigate the effects of saturation artifacts to reveal how chemical, genetic, and environmental factors affect cell state, providing an effective tool for studying the field of biological variability and improving image quality in analysis.

The enzymology of the key steps in the archaeal phospholipid biosynthetic pathway has been elucidated in recent years. In contrast, the complete biosynthetic pathways for proposed membrane regulators consisting of polyterpenes such as carotenoids, respiratory quinones and polyprenols remain unknown. Notably, the multiplicity of geranylgeranyl reductases (GGRs) in archaeal genomes has been correlated with the saturation of polyterpenes. Although GGRs, which are responsible for the saturation of the isoprene chains of phospholipids have been identified and studied in detail, there is little information regarding the structure and function of the paralogs. Here, we discuss the diversity of archaeal membrane-associated polyterpenes which is correlated with the genomic loci, structural and sequence-based analyses of GGR paralogs.

Ammonia known as harmful gas that could impact on health and environment. Typically, ammonia gas emitted by fertilizer industry, rubber factory, etc. There are many options for advance industry to control ammonia gas pollution, absorption tower using water scrubber and using activated carbon as adsorption reaction could be an option. But for middle- and lower-class industry, it is common in Indonesia, as seen on many rubber factories, ammonia gas pollution is serious problem to control, actually they have used wet scrubber but eficiency is lower about 47%. This study measure performance for ammonia elimination as gas pollutant using absorption tower and adsorption tower in laboratory scale. Using electrochemical gas sensor, we measure both ammonia concentration for inlet and outlet simultaneously to settle saturation point of these two types of ammonia emission control. In conclusion, Ammonia absorbed in water proportional to saturation time and absorbent volume. Highest absorbed ammonia concentration 1.538 mg/L on 4000 mL absorbent. For Adsorption system, saturation time proportional and correlated to adsorbent weight and Adsorption capacity reverse correlated to adsorbent weight. Optimum adsorption point can be achieved from intersection curve between saturation time and adsorption capacity which is 1200 grams adsorbent

In response to the fairness issue arising from the unequal delay of vehicles in different phases at intersections, considering the actual situation of small and variable delays for vehicles in low-saturation intersection phases, this paper proposes the concept of "sacrificing efficiency for fairness." Firstly, the universality of unfair delay phenomena at intersection phases is explained, especially at low-saturation intersections where the fluctuation in phase delays is 1.87 times higher than at other intersections. Then, a fairness evaluation index is constructed using information entropy, and the feasibility of the proposed approach is demonstrated. Subsequently, a signal optimization model that balances efficiency and fairness is proposed. Finally, the proposed model is validated through case studies, showing that it not only simultaneously considers efficiency and fairness but also has minimal impact on efficiency. Moreover, the changes to timing schemes in the efficiency model are much smaller compared to the model that only considers fairness. Sensitivity analysis reveals that the model performs better under low-saturation intersection conditions.

This paper presents a comprehensive analysis of the SEIRS COVID-19 pandemic model with saturated incidence rate. By modifying the existing model and proposing a new simplified version, we investigate the dynamics of disease transmission, including the impact of saturation terms on disease spread. Through stability analysis at disease-free and endemic equilibria, we aim to enhance understanding of the spread of COVID-19 and inform effective control strategies. Drawing on mathematical models and epidemiological insights, this study contributes to the ongoing efforts to combat the global pandemic.

Background: In antibiotic naïve populations, there is a strong association between the use of an antimicrobial and resistance to this antimicrobial. Less evidence is available as to whether this relationship is weakened in populations highly exposed to antimicrobials. Individuals taking HIV PrEP have a high intake of antimicrobials. We previously found that there was no difference in the prevalence of pheno- and genotypic antimicrobial resistance between two groups of PrEP clients who had, and had not, taken antimicrobials in the prior 6-months. Both groups did, however, have a higher prevalence of resistance than a sample of the general population. Methods: In the current study, we used zero-inflated negative binomial regression models to evaluate if there was an individual level association between the consumption of antimicrobials and 1. the minimum inhibitory susceptibilities of oral Neisseria subflava and 2. the abundance of antimicrobial resistance genes in the oropharynges of these individuals. Results: We found no evidence of an association between the consumption of antimicrobials and the minimum inhibitory susceptibilities of oral Neisseria subflava or the abundance of antimicrobial resistance genes in these individuals. Conclusions: We conclude that in high antimicrobial consumption populations, the association between antimicrobial consumption and resistance may be attenuated.

Saturated lights appear brighter than white lights of the same luminance. This phenomenon is known as the Helmholtz-Kohlrausch (H-K) effect and can be estimated by modeling achromatic luminance and saturation to total brightness. These models have been shown to differ between women and men and are more variable in women. The variation in brightness models among women may be due to hormonal changes across the menstrual cycle. To test this, total brightness and achromatic luminance were measured across blue, green, yellow-green, yellow, and red hues. These data were measured along with salivary hormone levels for nine cycling women at points representing the menstrual, peri-ovulation, and luteal phases. These data were also collected for seven oral contraceptive (OC) users. There were no main effects of OC use nor menstrual cycle phase on B/L ratios, but ratios were higher for the red stimulus in cycling women than OC users. Red B/L ratios were also higher for cycling women than OC users during the luteal phase. Estrogen, progesterone, and their interaction predicted 18% of the variation in brightness for cycling women. These models could not be fit for OC users, and estrogen only accounted for 5% of brightness variance with progesterone terms omitted. These findings and potential mechanisms are discussed in the context of previous results.

As development progresses, when the bottom hole flowing pressure or formation pressure is less than the saturation pressure of crude oil in the reservoir, oil and gas two-phase seepage occurs in the reservoir. Due to the characteristics of oil and gas two-phase seepage, after the oil and gas two-phase seepage occurs in the reservoir, the well production will be reduced, or even greatly reduced. Therefore, how to predict the horizontal well capacity better in this case is an important problem that needs to be solved urgently. In this paper, the method and process of establishing the transient calculation model of two-phase flow in horizontal wells are introduced in detail from three aspects: fluid physical properties, reservoir oil-gas two-phase seepage, and the coupling model of Inflow Performance and Flow in Wellbore. The model is more reliable through the verification of production data from five wells in two oilfields.

In the context of the COVID-19 Pandemic, the use of surgical masks has become the new normal. The use of these devices in exercise and medical situations has been advocated with the purpose of reducing contagions, but some concerns exist regarding its safety. We performed maximal treadmill stress tests in 12 healthy young subjects, with and without surgical mask use, and measured exercise capacity, oxygen saturation (rest, peak exercise and post-exercise) and electrocardiographic changes. Exercise capacity and Oxygen saturation levels decreased in peak exercise vs rest in a statistically significant manner when mask was used. ECG changes, although not significant, were present in 3 subjects when mask was used and disappeared when the test was made unmasked. We conclude that masked exercise has the potential to cause decreased exercise load and oxygen saturation and potentially cause diagnostic errors in medical exams.

The seasonally adjusted civilian labor force participation rate, the sum of employed and unemployed persons as a percentage of the civilian non-institutional population, is analysed in the general to specific modelling framework with a saturating set of step indicators from January 1977 through June 2018. The results indicate that, ceteris paribus, the rise in the ratio of women to men in the labor force in addition to positive demographic movements can largely account for the rise in the labor force participation rate up to January 2000. Subsequently, the aging population helps to explain the decline. Recessions play a transitory role.

The paper addresses the challenging issue of trajectory tracking for uncertain quadrotor UAVs, particularly under the constraints of input saturation and external disturbances. It introduces adaptive laws for managing uncertainties in mass and inertia moments without requiring prior knowledge, ensuring effective control even with varying system parameters. To counteract the effects of input saturation, the study incorporates an auxiliary system designed to compensate for these limitations. Additionally, a disturbance observer(DO) is utilized to manage and mitigate the impact of time-varying external disturbances. The proposed control strategy integrates a sliding mode adaptive control approach with an inner-outer loop structure, enhancing robustness and adaptability. Numerical simulations demonstrate the effectiveness of the designed control strategy.

This paper addresses a mode-dependent state-feedback H∞ control for descriptor hybrid systems, considering both the absence and presence of actuator saturation. Firstly, the necessary and sufficient conditions for the stochastic admissibility criterion with H∞ performance ? of the closed-loop system is proposed. Given the proposed non-convex condition, the author reformulates it into linear matrix inequalities (LMIs). Then, to extend the result to the systems with actuator saturation, the actuator saturated control input is expressed as a linear combination of given state-feedback control input and a virtual control input that remains under the saturation level. To verify this expression, the set invariant condition is also suggested by using the singular mode-dependent Lyapunov function candidate. Therefore, the LMI conditions for the existence of the mode-dependent state-feedback H∞ control and the ellipsoidal shape of invariant set are successfully derived. Two numerical examples demonstrate the effectiveness of the proposed approach in optimizing H∞ performance $\gamma$ and identifying the largest invariant set.

Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

Silicon photonics is emerging as a competitive platform for electronic-photonic integrated circuits (EPICs) at the 2 µm wavelength band where GeSn photodetectors (PDs) have proven to be efficient PDs. Here, we present a comprehensive theoretical study of GeSn vertical p-i-n homojunction waveguide photodetectors (WGPDs) that have a strain-free and defect-free GeSn active layer for 2-µm Si-based EPICs. The use of a narrow-gap GeSn alloy as the active layer can fully cover entire the 2 µm wavelength band. The waveguide structure allows for decoupling the photon-absorbing path and the carrier-collection path, thereby allowing for simultaneous achievement of high-responsivity and high-bandwidth (BW) operation at the 2-µm wavelength band. We present the theoretical models to calculate the carrier saturation velocities, optical absorption coefficient, responsivity, 3-dB bandwidth, zero-bias resistance, and detectivity, and optimize this device structure to achieve highest performance at the 2-µm wavelength band. The results indicate that the performance of the GeSn WGPD has strong dependence on the Sn composition and geometric parameters. The optimally designed GeSn WGPD with 10% Sn concentration can give responsivity of 1.55 A/W, detectivity of 6.12×1010 cmHz½W-1 at 2 µm wavelength, and ~97 GHz BW. Therefore, this optimally designed GeSn WGPD is a potential candidate for silicon photonic EPICs offering high-speed optical communications.

This paper studies the integrated design problems of control and guidance with parameter uncertainties, target disturbances, input constraints and actuator faults. Firstly, based on the integrated design idea of the missile guidance and control, the auxiliary variable is used to establish and transform it into a cascade system with input constraints, actuator faults and disturbances of unknown upper bounds. Secondly, the adaptive anti-saturation dynamic surface fault-tolerant controller is designed by using the back-stepping method, adaptive control, auxiliary system and tracking differentiator. By introducing the tracking differentiator and tangent barrier Lyapunov function, the computational explosion problem in the traditional back-stepping method is avoided and the angle of attack can be guaranteed in prospective range, respectively. Finally, the theoretical proof of the designed control strategy is given to ensure that the states of the closed-loop system are bounded. At the same time, the digital simulation of the maneuvering target of different maneuvering forms is carried out, which further illustrate the effectiveness and robustness of the designed control schemes.

In table tennis competitions the rule violation judgment with the greatest controversy is the height of the ball serve. This is because inaccuracy in the ball height judgment, which results in erroneous judgment, is unavoidable. Thus, we designed an automatic image judgment auxiliary system for table tennis ball height during service in this study. We used a high-speed camera to record the ball toss in the table tennis service. The designed algorithm architecture can automatically search for the ball and the position of the hand action under low light source conditions. The algorithm is mainly divided into hue-saturation-value color space processing and morphology processing using Hough transform to search for the circular ball. Experiment result shows that color segmentation can successfully and accurately determine the ball position under low light conditions. The morphology method can find the position of the hand and help determine the moment when the ball leaves the hand during the service ball toss. Finally, the actual size of the target is used to estimate the actual distance unit represented by the image pixel.

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

This paper presents a concise exploration of several analytical methods for extracting the parameters of the single-diode model (SDM) of a photovoltaic (PV) module under standard test conditions (STC). The paper investigates six methods and presents the detailed mathematical analysis leading to the development of each method. To evaluate the performance of these methods, MATLAB-based software has been developed and deployed to synthesize the results of each method when used to extract the SDM parameters of various PV test modules of different PV technologies. Similar software has also been developed to extract the same parameters using well-established numerical and iterative techniques. A comparison is subsequently made between the synthesized results and those obtained using numerical and iterative methods. The comparison indicates that in spite of the fact that analytical methods may involve fair amount of approximations, their accuracy can be comparable to that of their numerical and iterative counterparts, with the added advantage of significant reduction in computational complexity, and without the initialization and convergence difficulties, which are normally associated with numerical methods.

Rainfall is the main driver of hydrological processes in dryland environments and characterising the rainfall variability and processes of runoff generation are critical for understanding ecosystem function of catchments. Using remote sensing and in situ data sets, we assess the spatial and temporal variability of the rainfall, rainfall-runoff response, and effects of antecedent soil moisture and ground cover at different spatial scales on runoff coefficients in the Upper Burdekin catchment, northeast Australia, which is a major contributor of sediment and nutrients to the Great Barrier Reef. The high temporal and spatial variability of rainfall exerts significant controls on runoff generation processes. Rainfall amount and intensity are the primary runoff controls, and runoff coefficients for wet antecedent conditions were higher than for dry conditions. The majority of runoff occurred via surface runoff generation mechanisms, with subsurface runoff likely contributing little runoff due to the intense nature of rainfall events. At annual to seasonal temporal scales and for relatively large catchments, we could not detect a significant effect of ground cover on runoff. We conclude that in the range of moderate to large catchments (193 – 36,260 km²) runoff generation processes are sensitive to both antecedent soil moisture and ground cover. A higher runoff-ground cover correlation in drier months with sparse ground cover highlighted the critical role of cover at the onset of the wet season and how runoff generation is more sensitive to cover in drier months than in wetter months. The monthly water balance analysis indicates that runoff generation in wetter months (January and February) is partially influenced by saturation overland flow, most likely confined to saturated soils in riparian corridors, swales, and areas of shallow soil. By March and continuing through October, the soil ‘bucket’ progressively empties by evapotranspiration, and Hortonian overland flow becomes the dominant, if not exclusive, flow generation process. The results of this study can be used to better understand the rainfall-runoff relationships in dryland environments and subsequent exposure of coral reef ecosystems in Australia and elsewhere to terrestrial runoff.

Counter-current spontaneous imbibition of water is a critical oil-recovery mechanism. In the laboratory, the Amott test is a widely used technique to assess efficacy of brine imbibition into oil-saturated core plugs. The classic Amott-cell methodology was designed to estimate ultimate oil recovery, but not the recovery dynamics that provides essential information about the imbibition mechanisms. Retention of oil droplets at the external core surface and delayed onset of oil production are the two key artifacts of the classic Amott experiment. This retention, referred to here as the ``external-surface oil holdup effect'', often results in stepwise recovery curves that obscure true dynamics of spontaneous imbibition. To address these holdup drawbacks of the classic Amott method, we modified the Amott cell and experimental procedure. For the first time, using water-wet Indiana limestone cores saturated with brine and mineral oil, we showed that our improvements of the Amott method enabled accurate and reproducible measurements of oil-recovery dynamics. We used the Generalized Extreme Value (GEV) statistics to describe oil-production histories from water-wet heterogeneous limestone cores with finite initial water saturations, for the first time. We demonstrated that our four-parameter GEV model accurately described the recovery dynamics, and that optimal GEV parameter values systematically reflected the key characteristics of the oil-rock system, such as oil viscosity and rock permeability. These findings gave us a more fundamental understanding of spontaneous, counter-current imbibition mechanisms and insights into what constitutes a predictive model of counter-current water imbibition into oil-saturated rocks with finite initial water saturation.

This paper addresses the Collatz Conjecture, an open question in mathematics that postulates all positive integers will eventually reach one when a pair of specific operations are repeatedly applied. Despite its apparent simplicity, the conjecture lacks a formal proof. To tackle this enigma, we introduce Algebraic Inverse Trees (AITs), data structures that trace inverse operations of the Collatz sequence. This new approach not only elaborates our unique methodology but also sheds light on the underlying complexities of the Collatz Conjecture.

Archie model is the basis of calculating oil saturation, but there are some limitations when using this model to calculate oil saturation in water-flooded layer. The main reason is that the main parameters, such as rock resistivity and formation water resistivity, are constantly changing dynamic parameters in the underground with the influence of injected water. Considering that water-flooded layers changes with injection waters, influence factors of rock resistivity and formation water resistivity of primary parameters are analyzed. Considering the dynamic data of water cut is the most reactive underground fluid characteristics of real information, combined with dynamic and static, and the “double ratio” model of later development by the same sedimentary layer is established, which realizes the inversion of rock resistivity and formation water resistivity, then modified Archie model relating to water-flooded layers of the same sedimentary explaining formation. The explanation of actual data indicates that the “double ratio” model well considers the dynamic variation of production data, which makes the inversion of the flooded rock resistivity relatively accurate, besides, the modified Archie model can accurately calculate the oil saturation of water-flooded layers with a reasonable result, which offers scientific basis for the predicting of remaining oil distribution rules.

Photoplethysmography (PPG) based pulse oximetry devices normally use red and infrared illuminations to obtain oxygen saturation (SpO2) readings. In addition, the presence of motion artefacts severely restricts the utility of pulse oximetry physiological measurements. In the current study, a combination of green and orange illuminations from a multi-wavelength optoelectronic patch sensor (mOEPS) was investigated in order to improve robustness to subjects’ movements in the extraction of SpO2 measurement. Two experimental protocols with 31 healthy subjects were designed to determine SpO2 measurement. The datasets for the first protocol were collected from 15 subjects at rest, with the subjects free to move their hands. The datasets for the second protocol with 16 subjects were collected during cycling and running exercises. The results showed good agreements with SpO2 measurements (r = 0.98) in the both protocols. The outcomes promise a robust and cost-effective approach of physiological monitoring with the prospect of providing health monitoring that does not restrict user physical movements.

The most significant assumptions in the subdomain technique (i.e., based on the formal resolution of Maxwell's equations applied in subdomain) is defined by: “The iron parts (i.e., the teeth and the back-iron) are considered to be infinitely permeable so that the saturation effect is neglected”. In this paper, the author presents a new scientific contribution on improving of this method in two-dimensional (2-D) and in Cartesian coordinates by focusing on the consideration of iron. The subdomains connection is carried out in the two directions (i.e., x- and y-edges). For example, the improvement was performed by solving magnetostatic Maxwell's equations for an air- or iron-cored coil supplied by a direct current. To evaluate the efficacy of the proposed technique, the magnetic flux density distributions have been compared with those obtained by the 2-D finite-element analysis (FEA). The semi-analytical results are in quite satisfying agreement with those obtained by the 2-D FEA, considering both amplitude and waveform.

Infiltration based stormwater best management practices bring considerable economic, social and ecological benefits. Controlling stormwater quantity and quality are primarily important to prevent urban flooding and minimizing loads of pollutants to the receiving waters. However, there have been growing concerns about how the traditional design approach contributes to the failure of infiltration based BMP’s that have caused flooding, ponding, prolonged movement of surface water, and frequent clogging, etc. Many of these problems were due to the fact that the current design approaches of stormwater BMP’s only focus on surface hydrology and give little or no attention to the underline subsoil permeability rate and other constraints during the design and sizing process. As a result, we are exhibiting many newly constructed infiltration based BMP’s are failing to function well. This paper presents and demonstrates a new paradigm shift in designing infiltration-based stormwater BMP’s by combining subsurface hydrology and undelaying native soil constraints to establish acceptable criteria for sizing infiltration based BMPs.

In the full load operating range, wind turbines typically use pitch control to maintain rotor speed and output power at their rated values to guarantee the whole system’s safety. Blade pitch actuators are subject to physical limitations and safety requirements, which imposes strict constraints on pitch angle’s amplitude and rate of change. These constraints will bring windup problem to the integral part of the pitch controller. It leads to deterioration of the pitch control system’s performance or even the instability problem, especially for large-scale turbines operating in extreme uncertain wind conditions or suffering from cyber attacks. This paper designs an anti-windup robust pitch angle control strategy to deal with pitch rate constraint issue to enhance the security of control system. First, to facilitate controller design, a filtered tracking error technique is employed to transform the nonaffine form into an affine one. Subsequently, a feedback robust controller based on UDE is developed to handle the model’s uncertainty and external disturbances. To address the issue of integral saturation in the pitch system and guarantee its safety, an elliptical bounded constraint is integrated into the designed UDE strategy. This bounded UDE controller can improve the stability of power generation quality, reduces the mechanical loads on components and enhance the whole system’s safety. Finally, the effectiveness of the proposed scheme is verified on the Wind Turbine Blockset platform in Matlab/Simulink. It can achieve better performance than the traditional method.

To address the trajectory tracking issue for quadrotors working under the influence of external disturbances, a control scheme is designed for position and attitude trajectory tracking. Firstly, the quadrotor dynamic model is derived for control design. Secondly, adaptive integral backstepping control (AIBS) is employed in the position loop in which adaptive estimation is used to estimate the upper bounds of disturbances. Subsequently, a new adaptive backstepping fast nonsingular integral terminal sliding mode control (ABFNITSM) is proposed to follow desired Euler angles. The intro-duction of fast nonsingular terminal sliding mode and integral element is to realize fast convergence and accurate tracking. Dead zone technique is applied to minimize estimation errors. Besides, a saturation function is utilized to eliminate chattering phenomenon. Finally, simulation experiments are conducted under the Simulink environment. The proposed control is verified by comparing it with traditional integral terminal sliding mode control (ITSM) and integral backstepping control (IBS).

High rates of phosphorus (P) currently being applied to soils for the production of vegetables in the Mekong Delta, Vietnam has led to the concern of its negative effect on the economics and the environment. This research presents a comprehensive study on the determination of P supplying capacity in this region of Vietnam to examine the possibility of reducing P fertilizer input. One hundred twenty (120) soil samples were collected to evaluate total P and Bray 1 available P in the soils. Phosphorus maximum sorption, degree of P saturation, P release, and the effect of P fertilizer on corn (Zea mays L.) yield in greenhouse and fields were also determined. Total P concentrations of 56.7% soil samples evaluated yielded high P concentrations (>560 mg P/kg), while 74.2% of the samples had high Bray 1 available P concentrations (>20 mg P/kg soil). Maximum P sorption ranged from 149 to 555 mg P/kg soil, respectively and has negative correlation to available P (r = - 0.63*), degrees of P saturation ranged from 0.63 to 5.46% correlated to available P (r = 0.98**) and maximum P release ranged from 1.2 to 61.9 mg P/kg soil, respectively correlated to available P (r = 0.96**). Corn grown in soils with available P concentrations >15 mg P/kg did not respond to P fertilizer in greenhouse or field experiments. We conclude that many farmers in this region can reduce P fertilizer input, thus increasing their profits and reducing negative environmental impacts associated with excess soil P for sustainable agriculture.

We presented a fractional order model to capture the transmission dynamics of Anthrax infection with a nonlinear force of infection and its long-term impacts. Analysis by the standard Fabrizio Caputo approach established the model is well-posed and investigation on the stability of the model, Anthrax-free equilibrium as connected to the basic reproduction number R0

A Pediatric Sleep Questionnaire (PSQ) and a recording of the respiratory parameters with a noc-turnal home cardiorespiratory polygraphy (PG) are necessary to diagnose OSAS. Few researchers have studied how obesity could influence the respiratory parameters in OSAS children. The aim of the study was to investigate how obesity can influence sleep respiratory parameters in OSAS children. Methods: The study analyzes 56 Caucasian children and adolescents aged 11 ± 2.79 years with a BMI> 5th percentiles and PSQ value of 0.33. Children were divided into the Obesity Group (OG) with a BMI of  95th and the Control Group (CG) with a 5th<BMI> 95th percentile. All selected children underwent PG. Respiratory parameters were extracted to divide into levels of severity OSAS: snoring, mild, moderate, and severe. Results: The comparison analysis of AHI, SaO2, and Nadir between the OG and CG showed a statistical significance only for ODI (p = 0.02). The comparison analysis of PSQ between the OG and CG and of PSQ and respiratory parameters showed no significant result. A statistically significant correlation between BMI and AHI (r2=0.01), SaO2 (r2=0.09), and Nadir O2 (r2=0.00) was found. Conclusion: There was no strong correlation between Obesity and OSAS, but it was found between BMI increasing and AHI severity

The saturation properties of symmetric and asymmetric nuclear matter have been computed using the finite range simple effective interaction having Yukawa form-factor. The results of higher order derivatives of the energy per particle and the symmetry energy computed at saturation, namely, Q0, Ksym, Kτ, Qsym, are compared with the corresponding range of values extracted from studies involving theory, experiment and astrophysical observations. The ability of the equations of state computed with this simple effective interaction in predicting the threshold mass for prompt collapse in binary neutron star merger and gravitational redshift have been examined in terms of the compactness of the neutron star and the incompressibility at the central density of the maximum mass star. The correlations existing between neutron star properties with the nuclear matter saturation properties have been analyzed and compared with the predictions of other model calculations.

The western Sulige gas field is a new and key reserve area for the rolling development of the Sulige gas field in China. However, due to the complex gas–water relationship and the difficulty in identifying gas and water formation, the scale and benefit deployment of the gas field are seriously restricted. In particular, almost all of the wells in the area produce water and no water measurement has been carried out for any single well, which leads to an unclear understanding of the dynamic characteristics of the production wells, thus affecting the productivity calculations of the gas wells and the overall regional productivity evaluation. Based on the testing data for a gas well, the impacts of the reservoir property parameters on the gas and water production were analyzed by combining the production performance and static geological characteristics. It was determined that the physical parameters K, Kh, and φSg had good positive correlations with gas production but not with water production; thus, effective prediction cannot be obtained for water production in gas well testing. After the analysis of the liquid loading law, the gas wells were classified into three types: continuous liquid carrying production, slight liquid loading, and liquid loading wells. In general, up to 96% of the gas wells were liquid loaded. According to the different production performances exhibited in the different stages of the gas wells, five types of methods for diagnosing water production wells were proposed (gas testing, pilot production, gas–liquid two-phase measurement testing, liquid level detection, and production performance analysis), as well as the diagnostic criteria and corresponding solutions. To obtain real-time water production data for each well and investigate the change of water-gas ratio (WGR) during the whole production process, a water production splitting method for gas wells based on three-dimensional geological modeling and numerical simulation combined with the constraints of the total water production of gas gathering stations was explored and established. The splitting results can be used to evaluate the water and gas productivity of gas wells and determine the best deliquification period. The gas well productivity when water production was considered was about 10% lower than that when water production was not considered. The best deliquification period was determined to be 125 days for wells with small water production, 20 days for wells with moderate water production, and 3 days for wells with serious water production. The results of this study could provide technical support for the scientific evaluation of gas well production indicators, reduction of development costs, and improvement of oil recovery.

Taste signaling is a complex process that is linked to obesity and its associated metabolic syndromes. The sweet taste is mediated through a heterodimeric G protein coupled receptor (GPRC) in a species-specific manner and at multi-tissue specific levels. The sweet receptor recognizes a large number of ligands with structural and functional diversities to modulate different amplitudes of downstream signaling pathway(s). The human sweet-taste receptor has been extremely difficult to study by biophysical methods due to inadequate methods for producing large homogeneous quantities of the taste-receptor protein and a lack of reliable in vitro assays to precisely measure productive ligand binding modes leading to activity upon their interactions with the receptor protein. We report a multimodal high throughput assays to monitor ligand binding, receptor stability and conformational changes to model the molecular interactions between ligand-receptor. We applied saturation transfer difference nuclear magnetic resonance spectroscopy (STD-NMR) complemented by differential scanning calorimetry (DSC), circular dichroism (CD) spectroscopy, and intrinsic fluorescence spectroscopy (IF) to characterize binding interactions. Our method using complementary NMR and biophysical analysis is advantageous to study the mechanism of ligand binding and signaling processes in other GPCRs.

The paper presents the main experimental capabilities of the automatic system for the study of the interaction between porous media and atmosphere. This system is one of the possible variants of patent 2-241-477. The paper shows the result of a drying and wetting study of a tailings sample. The sample is 32 cm in height and 29 cm in diameter. The saturation and drying process was carried out at 26 degrees Celsius at the sample surface, an air velocity of 2 m/s and a relative humidity of 60%. The recharge applied to the column surface was 0.3 cm3/cm2/minute. The results show the effectiveness of the system in controlling the spatial-temporal variation of different physical properties of the porous medium in the vertical and surface profile. The controlled variables include volumetric water content, suction, relative humidity, sample weight variation due to recharge or drying, shrinkage, temperature, etc. The experiment shows how the tailings saturate very quickly but dry very slowly. Tailings consolidation occurs in the drying and wetting processes, being higher in the first one.

Research question/problem: This comprehensive review and comparative analysis aims to investigate the significance of enhancing oxygen provision in the context of COVID-19, focusing on the implications for healthcare policies and services.Background/context: The study addresses the shift in the oxygen dissociation curve of blood in COVID-19 patients, emphasizing the impact on oxygen delivery to tissues and the challenges it poses for clinical management. It also explores the disruption of healthcare systems due to the pandemic and the integration of social determinants of health in clinical environments.Methodology: The research incorporates a thorough literature review, comparative analysis of diverse approaches to oxygen delivery, and examination of successful interventions through case studies and best practices. Data collection techniques include the review of scholarly articles, case studies, and policy documents.Results/Key findings: The study highlights the imperative for augmented oxygen supply and the significance of maintaining appropriate oxygen saturation levels, especially in the context of respiratory illnesses like COVID-19. It also emphasizes the positive correlation between increased oxygen saturation levels and life expectancy, indicating potential health benefits of enhanced oxygen availability.Conclusions/Implications: The findings underscore the need for a structured approach to oxygen therapy and the importance of equitable distribution of oxygen to underserved regions. The implications of the research extend to enhancing healthcare policies and services regarding oxygen provision during the COVID-19 pandemic, especially in rural and remote areas.